DOCS-RPHY-MIB

File: DOCS-RPHY-MIB.mib (248182 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
SNMP-FRAMEWORK-MIB INET-ADDRESS-MIB UUID-TC-MIB
IANA-ENTITY-MIB IANAifType-MIB ENTITY-MIB
ENTITY-SENSOR-MIB IP-MIB IF-MIB
DOCS-IF3-MIB CLAB-DEF-MIB DOCS-IETF-BPI2-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
Gauge32 Counter32 Counter64
Integer32 TimeTicks TruthValue
MacAddress TimeStamp AutonomousType
DateAndTime PhysAddress TEXTUAL-CONVENTION
OBJECT-GROUP MODULE-COMPLIANCE SnmpAdminString
InetAddressType InetAddress InetPortNumber
InetVersion InetAddressPrefixLength UUIDorZero
IANAPhysicalClass IANAifType PhysicalIndex
PhysicalIndexOrZero EntitySensorDataType EntitySensorDataScale
EntitySensorPrecision EntitySensorValue EntitySensorStatus
IpAddressOriginTC IpAddressStatusTC Ipv6AddressIfIdentifierTC
InterfaceIndex ifIndex InterfaceIndexOrZero
IfDirection clabProjDocsis DocsX509ASN1DEREncodedCertificate

Defined Types

RphyChannelType  
This data type indicates the type of RPHY channel.
TEXTUAL-CONVENTION    
  INTEGER other(0), dsScQam(1), dsOfdm(2), ndf(3), scte551Fwd(4), usAtdma(5), usOfdma(6), reserved(7), ndr(8), scte551Ret(9)  

RphyEventSeverityType  
This data type indicates the severity level of an RPD event.
TEXTUAL-CONVENTION    
  INTEGER emergency(0), alert(1), critical(2), error(3), warning(4), notice(5), information(6), debug(7)  

DocsRphyRpdDevInfoEntry  
SEQUENCE    
  docsRphyRpdDevInfoUniqueId MacAddress
  docsRphyRpdDevInfoSysUpTime TimeStamp
  docsRphyRpdDevInfoNumCrashFilesAvail Unsigned32

DocsRphyRpdDevIdentificationEntry  
SEQUENCE    
  docsRphyRpdDevIdVendorName SnmpAdminString
  docsRphyRpdDevIdVendorId Unsigned32
  docsRphyRpdDevIdModelNum SnmpAdminString
  docsRphyRpdDevIdSerialNum SnmpAdminString
  docsRphyRpdDevIdDeviceAlias SnmpAdminString
  docsRphyRpdDevIdDeviceDescr SnmpAdminString
  docsRphyRpdDevIdHwRev SnmpAdminString
  docsRphyRpdDevIdCurrSwVer SnmpAdminString
  docsRphyRpdDevIdBootRomVer SnmpAdminString
  docsRphyRpdDevIdUsBurstRcvrVendorId Unsigned32
  docsRphyRpdDevIdUsBurstRcvrModelNum SnmpAdminString
  docsRphyRpdDevIdUsBurstRcvrDrivVer SnmpAdminString
  docsRphyRpdDevIdUsBurstRcvrSerialNum SnmpAdminString
  docsRphyRpdDevIdRcpProtocolVer SnmpAdminString
  docsRphyRpdDevIdRcpSchemaVer SnmpAdminString

DocsRphyRpdDevLocationEntry  
SEQUENCE    
  docsRphyRpdDevLocationDescr SnmpAdminString
  docsRphyRpdDevLocationLatitude SnmpAdminString
  docsRphyRpdDevLocationLongitude SnmpAdminString

DocsRphyRpdDevCoresConnectedEntry  
SEQUENCE    
  docsRphyRpdDevCoresConnectedCoreId MacAddress
  docsRphyRpdDevCoresConnectedAddressType InetAddressType
  docsRphyRpdDevCoresConnectedAddress InetAddress
  docsRphyRpdDevCoresConnectedIsPrincipal TruthValue
  docsRphyRpdDevCoresConnectedName SnmpAdminString
  docsRphyRpdDevCoresConnectedVendorId Unsigned32

DocsRphyRpdDevCapabilitiesEntry  
SEQUENCE    
  docsRphyRpdDevCapabNumDsPorts Unsigned32
  docsRphyRpdDevCapabNumUsPorts Unsigned32
  docsRphyRpdDevCapabNumTenGeNsPorts Unsigned32
  docsRphyRpdDevCapabNumOneGeNsPorts Unsigned32
  docsRphyRpdDevCapabNumDsScQamChans Unsigned32
  docsRphyRpdDevCapabNumDsOfdmChans Unsigned32
  docsRphyRpdDevCapabNumUsScQamChans Unsigned32
  docsRphyRpdDevCapabNumUsOfdmaChans Unsigned32
  docsRphyRpdDevCapabNumDsOob55d1Chans Unsigned32
  docsRphyRpdDevCapabNumUsOob55d1Chans Unsigned32
  docsRphyRpdDevCapabNumDsOob55d2Modules Unsigned32
  docsRphyRpdDevCapabNumUsOob55d2Demods Unsigned32
  docsRphyRpdDevCapabNumNdfChans Unsigned32
  docsRphyRpdDevCapabNumNdrChans Unsigned32
  docsRphyRpdDevCapabNumDsPspFlowsPerChan Unsigned32
  docsRphyRpdDevCapabNumUsPspFlowsPerChan Unsigned32
  docsRphyRpdDevCapabNumAsynchVideoChans Unsigned32
  docsRphyRpdDevCapabNumCwToneGens Unsigned32
  docsRphyRpdDevCapabLowestCwToneFreq Unsigned32
  docsRphyRpdDevCapabHighestCwToneFreq Unsigned32
  docsRphyRpdDevCapabMaxCwTonePwr Unsigned32
  docsRphyRpdDevCapabQamAsPilot TruthValue
  docsRphyRpdDevCapabSupportsUdpEncap TruthValue
  docsRphyRpdDevCapabSupportsFlowTags TruthValue
  docsRphyRpdDevCapabSupportsFreqTilt TruthValue
  docsRphyRpdDevCapabTiltRange Unsigned32
  docsRphyRpdDevCapabBufferDepthMonAlertSupp BITS
  docsRphyRpdDevCapabBufferDepthCfgSupp BITS
  docsRphyRpdDevCapabRpdUcdProcTime Unsigned32
  docsRphyRpdDevCapabRpdUcdChgNullGrtTime Unsigned32
  docsRphyRpdDevCapabMultiSectionTimingMerRep INTEGER

DocsRphyRpdDevChanReachabilityEntry  
SEQUENCE    
  docsRphyRpdDevChanReachabilityEnetPortIndex Unsigned32
  docsRphyRpdDevChanReachabilityRfPortIndex Unsigned32
  docsRphyRpdDevChanReachabilityChanType RphyChannelType
  docsRphyRpdDevChanReachabilityStartChanIndex Unsigned32
  docsRphyRpdDevChanReachabilityEndChanIndex Unsigned32

DocsRphyRpdDevDsUsRfPortAllocEntry  
SEQUENCE    
  docsRphyRpdDevDsUsRfPortAllocIndex Unsigned32
  docsRphyRpdDevDsUsRfPortAllocDirection IfDirection
  docsRphyRpdDevDsUsRfPortAllocScQamChans Unsigned32
  docsRphyRpdDevDsUsRfPortAllocOfdmChans Unsigned32
  docsRphyRpdDevDsUsRfPortAllocOob551Chans Unsigned32
  docsRphyRpdDevDsUsRfPortAllocNdChans Unsigned32

DocsRphyRpdDevL2tpSessionInfoEntry  
SEQUENCE    
  docsRphyRpdDevL2tpSessionInfoLocalLcceIpAddrType InetAddressType
  docsRphyRpdDevL2tpSessionInfoLocalLcceIpAddr InetAddress
  docsRphyRpdDevL2tpSessionInfoLocalId Unsigned32
  docsRphyRpdDevL2tpSessionInfoRemoteLcceIpAddrType InetAddressType
  docsRphyRpdDevL2tpSessionInfoRemoteLcceIpAddr InetAddress
  docsRphyRpdDevL2tpSessionInfoRemoteId Unsigned32
  docsRphyRpdDevL2tpSessionInfoCoreId MacAddress
  docsRphyRpdDevL2tpSessionInfoConnCtrlID Unsigned32
  docsRphyRpdDevL2tpSessionInfoUdpPort InetPortNumber
  docsRphyRpdDevL2tpSessionInfoDescr SnmpAdminString
  docsRphyRpdDevL2tpSessionInfoSessionType INTEGER
  docsRphyRpdDevL2tpSessionInfoSessionSubType INTEGER
  docsRphyRpdDevL2tpSessionInfoMaxPayload Unsigned32
  docsRphyRpdDevL2tpSessionInfoPathPayload Unsigned32
  docsRphyRpdDevL2tpSessionInfoRpdIfMtu Unsigned32
  docsRphyRpdDevL2tpSessionInfoCoreIfMtu Unsigned32
  docsRphyRpdDevL2tpSessionInfoErrorCode INTEGER
  docsRphyRpdDevL2tpSessionInfoCreationTime TimeStamp
  docsRphyRpdDevL2tpSessionInfoOperStatus INTEGER
  docsRphyRpdDevL2tpSessionInfoLocalStatus BITS
  docsRphyRpdDevL2tpSessionInfoLastChange TimeTicks

DocsRphyRpdDevL2tpSessionStatsEntry  
SEQUENCE    
  docsRphyRpdDevL2tpSessionStatsOutOfSeqPkts Counter32

DocsRphyRpdDevDiagStatusEntry  
SEQUENCE    
  docsRphyRpdDevDiagStatusProbableCause SnmpAdminString
  docsRphyRpdDevDiagStatusAdditionalText SnmpAdminString
  docsRphyRpdDevDiagStatusSeverityLevel RphyEventSeverityType

DocsRphyRpdDevDepiMcastSessionEntry  
SEQUENCE    
  docsRphyRpdDevDepiMcastSessionIpAddrType InetAddressType
  docsRphyRpdDevDepiMcastSessionGrpIpAddr InetAddress
  docsRphyRpdDevDepiMcastSessionSrcIpAddr InetAddress
  docsRphyRpdDevDepiMcastSessionLocalLcceIpAddr InetAddress
  docsRphyRpdDevDepiMcastSessionRemoteLcceIpAddr InetAddress
  docsRphyRpdDevDepiMcastSessionId Unsigned32
  docsRphyRpdDevDepiMcastSessionJoinTime DateAndTime

DocsRphyRpdDevEventLogEntry  
SEQUENCE    
  docsRphyRpdDevEventLogIndex Unsigned32
  docsRphyRpdDevEventLogFirstTime DateAndTime
  docsRphyRpdDevEventLogLastTime DateAndTime
  docsRphyRpdDevEventLogCounts Counter32
  docsRphyRpdDevEventLogLevel RphyEventSeverityType
  docsRphyRpdDevEventLogId Unsigned32
  docsRphyRpdDevEventLogText SnmpAdminString

DocsRphyRpdDevOob551UsChanStatusEntry  
SEQUENCE    
  docsRphyRpdDevOob551UsChanStatusRfPort Unsigned32
  docsRphyRpdDevOob551UsChanStatusChannelId Unsigned32
  docsRphyRpdDevOob551UsChanStatusNcIpAddrType InetAddressType
  docsRphyRpdDevOob551UsChanStatusNcIpAddr InetAddress
  docsRphyRpdDevOob551UsChanStatusArpdSrcIpAddrType InetAddressType
  docsRphyRpdDevOob551UsChanStatusArpdSrcIpAddr InetAddress
  docsRphyRpdDevOob551UsChanStatusPerfectCellsRcvd Counter64
  docsRphyRpdDevOob551UsChanStatusCorrectedCellsRcvd Counter64
  docsRphyRpdDevOob551UsChanStatusUncorrectableCellsRcvd Counter64
  docsRphyRpdDevOob551UsChanStatusTotalCellsRcvd Counter64
  docsRphyRpdDevOob551UsChanStatusPwrLevel Integer32
  docsRphyRpdDevOob551UsChanStatusMaxPwrLevel Integer32
  docsRphyRpdDevOob551UsChanStatusMinPwrLevel Integer32
  docsRphyRpdDevOob551UsChanStatusCounterDiscontinuityTime TimeStamp

DocsRphyRpdDevCrashDataFileStatusEntry  
SEQUENCE    
  docsRphyRpdDevCrashDataFileStatusIndex Unsigned32
  docsRphyRpdDevCrashDataFileStatusFilename SnmpAdminString
  docsRphyRpdDevCrashDataFileStatusFileStatus INTEGER

DocsRphyRpdDevUsSignalQualityEntry  
SEQUENCE    
  docsRphyRpdDevUsSignalQualityRfPort Unsigned32
  docsRphyRpdDevUsSignalQualityChannelIfIndex InterfaceIndex
  docsRphyRpdDevUsSignalQualityRxMer Integer32
  docsRphyRpdDevUsSignalQualityRxMerSamples Unsigned32
  docsRphyRpdDevUsSignalQualityUnerroreds Counter64
  docsRphyRpdDevUsSignalQualityCorrecteds Counter64
  docsRphyRpdDevUsSignalQualityUncorrectables Counter64

DocsRphyRpdIfPhysEntityEntry  
SEQUENCE    
  docsRphyRpdIfPhysEntityIndex PhysicalIndex
  docsRphyRpdIfPhysEntityDescr SnmpAdminString
  docsRphyRpdIfPhysEntityVendorType AutonomousType
  docsRphyRpdIfPhysEntityContainedIn PhysicalIndexOrZero
  docsRphyRpdIfPhysEntityClass IANAPhysicalClass
  docsRphyRpdIfPhysEntityParentRelPos Integer32
  docsRphyRpdIfPhysEntityName SnmpAdminString
  docsRphyRpdIfPhysEntityHardwareRev SnmpAdminString
  docsRphyRpdIfPhysEntityFirmwareRev SnmpAdminString
  docsRphyRpdIfPhysEntitySoftwareRev SnmpAdminString
  docsRphyRpdIfPhysEntitySerialNum SnmpAdminString
  docsRphyRpdIfPhysEntityMfgName SnmpAdminString
  docsRphyRpdIfPhysEntityModelName SnmpAdminString
  docsRphyRpdIfPhysEntityAlias SnmpAdminString
  docsRphyRpdIfPhysEntityAssetID SnmpAdminString
  docsRphyRpdIfPhysEntityIsFRU TruthValue
  docsRphyRpdIfPhysEntityMfgDate DateAndTime
  docsRphyRpdIfPhysEntityUris OCTET STRING
  docsRphyRpdIfPhysEntityUUID UUIDorZero
  docsRphyRpdIfPhysEntityCoreIfIndex InterfaceIndexOrZero

DocsRphyRpdIfPhysEntSensorEntry  
SEQUENCE    
  docsRphyRpdIfPhysEntSensorType EntitySensorDataType
  docsRphyRpdIfPhysEntSensorScale EntitySensorDataScale
  docsRphyRpdIfPhysEntSensorPrecision EntitySensorPrecision
  docsRphyRpdIfPhysEntSensorValue EntitySensorValue
  docsRphyRpdIfPhysEntSensorOperStatus EntitySensorStatus
  docsRphyRpdIfPhysEntSensorUnitsDisplay SnmpAdminString
  docsRphyRpdIfPhysEntSensorValueTimeStamp TimeStamp
  docsRphyRpdIfPhysEntSensorValueUpdateRate Unsigned32

DocsRphyRpdIfEnetEntry  
SEQUENCE    
  docsRphyRpdIfEnetPortIndex Unsigned32
  docsRphyRpdIfEnetDescr SnmpAdminString
  docsRphyRpdIfEnetName SnmpAdminString
  docsRphyRpdIfEnetAlias SnmpAdminString
  docsRphyRpdIfEnetType IANAifType
  docsRphyRpdIfEnetMtu Integer32
  docsRphyRpdIfEnetPhysAddress PhysAddress
  docsRphyRpdIfEnetAdminStatus INTEGER
  docsRphyRpdIfEnetOperStatus INTEGER
  docsRphyRpdIfEnetLastChange TimeTicks
  docsRphyRpdIfEnetLinkUpDownTrapEnable TruthValue
  docsRphyRpdIfEnetHighSpeed Gauge32
  docsRphyRpdIfEnetPromiscuousMode TruthValue
  docsRphyRpdIfEnetConnectorPresent TruthValue

DocsRphyRpdIfEnetStatsEntry  
SEQUENCE    
  docsRphyRpdIfEnetStatsInOctets Counter64
  docsRphyRpdIfEnetStatsOutOctets Counter64
  docsRphyRpdIfEnetStatsInFrames Counter64
  docsRphyRpdIfEnetStatsOutFrames Counter64
  docsRphyRpdIfEnetStatsInUnicastOctets Counter64
  docsRphyRpdIfEnetStatsOutUnicastOctets Counter64
  docsRphyRpdIfEnetStatsInUnicastFrames Counter64
  docsRphyRpdIfEnetStatsOutUnicastFrames Counter64
  docsRphyRpdIfEnetStatsInMulticastOctets Counter64
  docsRphyRpdIfEnetStatsOutMulticastOctets Counter64
  docsRphyRpdIfEnetStatsInMulticastFrames Counter64
  docsRphyRpdIfEnetStatsOutMulticastFrames Counter64
  docsRphyRpdIfEnetStatsInBroadcastOctets Counter64
  docsRphyRpdIfEnetStatsOutBroadcastOctets Counter64
  docsRphyRpdIfEnetStatsInBroadcastFrames Counter64
  docsRphyRpdIfEnetStatsOutBroadcastFrames Counter64
  docsRphyRpdIfEnetStatsInDiscards Counter64
  docsRphyRpdIfEnetStatsOutDiscards Counter64
  docsRphyRpdIfEnetStatsInErrors Counter64
  docsRphyRpdIfEnetStatsOutErrors Counter64
  docsRphyRpdIfEnetStatsInUnknownProtos Counter64
  docsRphyRpdIfEnetStatsCounterDiscontinuityTime TimeStamp

DocsRphyRpdIfRpdEnetToCoreEntityMapEntry  
SEQUENCE    
  docsRphyRpdIfRpdEnetToCoreEntityMapEntityIndex Unsigned32

DocsRphyRpdIfCoreToRpdMapEntry  
SEQUENCE    
  docsRphyRpdIfCoreToRpdMapRpdUniqueId MacAddress
  docsRphyRpdIfCoreToRpdMapRpdRfPortDirection IfDirection
  docsRphyRpdIfCoreToRpdMapRpdRfPortIndex Unsigned32
  docsRphyRpdIfCoreToRpdMapRpdRfChanType RphyChannelType
  docsRphyRpdIfCoreToRpdMapRpdRfChanIndex Unsigned32

DocsRphyRpdIfRpdToCoreMapEntry  
SEQUENCE    
  docsRphyRpdIfRpdToCoreMapRpdRfPortDirection IfDirection
  docsRphyRpdIfRpdToCoreMapRpdRfPortIndex Unsigned32
  docsRphyRpdIfRpdToCoreMapRpdRfChanType RphyChannelType
  docsRphyRpdIfRpdToCoreMapRpdRfChanIndex Unsigned32
  docsRphyRpdIfRpdToCoreMapCoreIfIndex InterfaceIndex

DocsRphyRpdIpv4GrpEntry  
SEQUENCE    
  docsRphyRpdIpv4GrpDefaultTTL Integer32
  docsRphyRpdIpv4GrpInterfaceTableLastChange TimeStamp

DocsRphyRpdIpv6GrpEntry  
SEQUENCE    
  docsRphyRpdIpv6GrpIpDefaultHopLimit Integer32
  docsRphyRpdIpv6GrpInterfaceTableLastChange TimeStamp
  docsRphyRpdIpv6GrpIfStatsTableLastChange TimeStamp

DocsRphyRpdIpv4InterfaceEntry  
SEQUENCE    
  docsRphyRpdIpv4InterfaceEnableStatus INTEGER
  docsRphyRpdIpv4InterfaceRetransmitTime Unsigned32

DocsRphyRpdIpv6InterfaceEntry  
SEQUENCE    
  docsRphyRpdIpv6InterfaceIdentifier Ipv6AddressIfIdentifierTC
  docsRphyRpdIpv6InterfaceEnableStatus INTEGER
  docsRphyRpdIpv6InterfaceReachableTime Unsigned32
  docsRphyRpdIpv6InterfaceRetransmitTime Unsigned32

DocsRphyRpdIpIfStatsEntry  
SEQUENCE    
  docsRphyRpdIpIfStatsIPVersion InetVersion
  docsRphyRpdIpIfStatsInReceives Counter64
  docsRphyRpdIpIfStatsInOctets Counter64
  docsRphyRpdIpIfStatsInHdrErrors Counter64
  docsRphyRpdIpIfStatsInNoRoutes Counter64
  docsRphyRpdIpIfStatsInAddrErrors Counter64
  docsRphyRpdIpIfStatsInUnknownProtos Counter64
  docsRphyRpdIpIfStatsInTruncatedPkts Counter64
  docsRphyRpdIpIfStatsInDiscards Counter64
  docsRphyRpdIpIfStatsInDelivers Counter64
  docsRphyRpdIpIfStatsOutRequests Counter64
  docsRphyRpdIpIfStatsOutDiscards Counter64
  docsRphyRpdIpIfStatsOutTransmits Counter64
  docsRphyRpdIpIfStatsOutOctets Counter64
  docsRphyRpdIpIfStatsInMcastPkts Counter64
  docsRphyRpdIpIfStatsInMcastOctets Counter64
  docsRphyRpdIpIfStatsOutMcastPkts Counter64
  docsRphyRpdIpIfStatsOutMcastOctets Counter64
  docsRphyRpdIpIfStatsDiscontinuityTime TimeStamp
  docsRphyRpdIpIfStatsRefreshRate Unsigned32

DocsRphyRpdIpAddressEntry  
SEQUENCE    
  docsRphyRpdIpAddressAddrType InetAddressType
  docsRphyRpdIpAddressAddr InetAddress
  docsRphyRpdIpAddressEnetPortIndex Unsigned32
  docsRphyRpdIpAddressType INTEGER
  docsRphyRpdIpAddressPrefixLen InetAddressPrefixLength
  docsRphyRpdIpAddressOrigin IpAddressOriginTC
  docsRphyRpdIpAddressStatus IpAddressStatusTC
  docsRphyRpdIpAddressCreated TimeStamp
  docsRphyRpdIpAddressLastChanged TimeStamp

DocsRphyRpdIpNetToPhysicalEntry  
SEQUENCE    
  docsRphyRpdIpNetToPhysicalNetAddressType InetAddressType
  docsRphyRpdIpNetToPhysicalNetAddress InetAddress
  docsRphyRpdIpNetToPhysicalPhysAddress PhysAddress
  docsRphyRpdIpNetToPhysicalLastUpdated TimeStamp
  docsRphyRpdIpNetToPhysicalType INTEGER
  docsRphyRpdIpNetToPhysicalState INTEGER

DocsRphyRpdIpDefaultRouterEntry  
SEQUENCE    
  docsRphyRpdIpDefaultRouterAddressType InetAddressType
  docsRphyRpdIpDefaultRouterAddress InetAddress
  docsRphyRpdIpDefaultRouterLifetime Unsigned32
  docsRphyRpdIpDefaultRouterPreference INTEGER

DocsRphyRpdIpIcmpMsgStatsEntry  
SEQUENCE    
  docsRphyRpdIpIcmpMsgStatsIPVersion InetVersion
  docsRphyRpdIpIcmpMsgStatsType Integer32
  docsRphyRpdIpIcmpMsgStatsInPkts Counter64
  docsRphyRpdIpIcmpMsgStatsOutPkts Counter64

DocsRphyCcapL2tpSessionInfoEntry  
SEQUENCE    
  docsRphyCcapL2tpSessionInfoLocalLcceIpAddrType InetAddressType
  docsRphyCcapL2tpSessionInfoLocalLcceIpAddr InetAddress
  docsRphyCcapL2tpSessionInfoLocalId Unsigned32
  docsRphyCcapL2tpSessionInfoRemoteLcceIpAddrType InetAddressType
  docsRphyCcapL2tpSessionInfoRemoteLcceIpAddr InetAddress
  docsRphyCcapL2tpSessionInfoRemoteId Unsigned32
  docsRphyCcapL2tpSessionInfoCoreId MacAddress
  docsRphyCcapL2tpSessionInfoConnCtrlID Unsigned32
  docsRphyCcapL2tpSessionInfoUdpPort InetPortNumber
  docsRphyCcapL2tpSessionInfoDescr SnmpAdminString
  docsRphyCcapL2tpSessionInfoSessionType INTEGER
  docsRphyCcapL2tpSessionInfoSessionSubType INTEGER
  docsRphyCcapL2tpSessionInfoMaxPayload Unsigned32
  docsRphyCcapL2tpSessionInfoPathPayload Unsigned32
  docsRphyCcapL2tpSessionInfoRpdIfMtu Unsigned32
  docsRphyCcapL2tpSessionInfoCoreIfMtu Unsigned32
  docsRphyCcapL2tpSessionInfoIncludeDOCSISMsgs TruthValue
  docsRphyCcapL2tpSessionInfoErrorCode INTEGER
  docsRphyCcapL2tpSessionInfoCreationTime TimeStamp
  docsRphyCcapL2tpSessionInfoOperStatus INTEGER
  docsRphyCcapL2tpSessionInfoLocalStatus BITS
  docsRphyCcapL2tpSessionInfoLastChange TimeTicks

DocsRphyCcapL2tpSessionFlowEntry  
SEQUENCE    
  docsRphyCcapL2tpSessionFlowPspFlowId Unsigned32

DocsRphyCcapL2tpSessionStatsEntry  
SEQUENCE    
  docsRphyCcapL2tpSessionStatsOutOfSeqPkts Counter32

DocsRphyCcapCinDsLatencyEntry  
SEQUENCE    
  docsRphyCcapCinDsLatencyLastVal Unsigned32
  docsRphyCcapCinDsLatencyLastValTime TimeTicks
  docsRphyCcapCinDsLatencyInterval Unsigned32

DocsRphyCcapSessionCinDsLatencyStatsEntry  
SEQUENCE    
  docsRphyCcapSessionCinDsLatencyStatsIntervalSeq Unsigned32
  docsRphyCcapSessionCinDsLatencyStatsVal Unsigned32
  docsRphyCcapSessionCinDsLatencyStatsValTime TimeTicks

Defined Values

docsRphyMib 1.3.6.1.4.1.4491.2.1.30
This MIB module contains the management objects for the Remote PHY Device (RPD) management. Copyright 2016-2017 Cable Television Laboratories, Inc. All rights reserved.
MODULE-IDENTITY    

docsRphyNotifications 1.3.6.1.4.1.4491.2.1.30.0
OBJECT IDENTIFIER    

docsRphyObjects 1.3.6.1.4.1.4491.2.1.30.1
OBJECT IDENTIFIER    

docsRphyConformance 1.3.6.1.4.1.4491.2.1.30.2
OBJECT IDENTIFIER    

docsRphyRpdDevMibObjects 1.3.6.1.4.1.4491.2.1.30.1.1
OBJECT IDENTIFIER    

docsRphyRpdIfMibObjects 1.3.6.1.4.1.4491.2.1.30.1.2
OBJECT IDENTIFIER    

docsRphyRpdIpMibObjects 1.3.6.1.4.1.4491.2.1.30.1.3
OBJECT IDENTIFIER    

docsRphyCcapMibObjects 1.3.6.1.4.1.4491.2.1.30.1.4
OBJECT IDENTIFIER    

docsRphyCcapSecMibObjects 1.3.6.1.4.1.4491.2.1.30.1.5
OBJECT IDENTIFIER    

docsRphyRpdIpIcmpMibObjects 1.3.6.1.4.1.4491.2.1.30.1.3.9
OBJECT IDENTIFIER    

docsRphyCompliances 1.3.6.1.4.1.4491.2.1.30.2.1
OBJECT IDENTIFIER    

docsRphyGroups 1.3.6.1.4.1.4491.2.1.30.2.2
OBJECT IDENTIFIER    

docsRphyRpdDevInfoTable 1.3.6.1.4.1.4491.2.1.30.1.1.1
This table identifies the RPD for which the details and statistics are being provided.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdDevInfoEntry

docsRphyRpdDevInfoEntry 1.3.6.1.4.1.4491.2.1.30.1.1.1.1
The conceptual row of docsRphyRpdDevInfoTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdDevInfoEntry  

docsRphyRpdDevInfoUniqueId 1.3.6.1.4.1.4491.2.1.30.1.1.1.1.1
This attribute specifies a globally unique 6-byte identifier for the RPD. By convention, an RPD SHOULD use the MAC address of the lowest numbered Ethernet port facing the CIN.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

docsRphyRpdDevInfoSysUpTime 1.3.6.1.4.1.4491.2.1.30.1.1.1.1.2
This attribute is the time (in hundredths of a second) since the RPD was last re-initialized. This value is reported by the RPD.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

docsRphyRpdDevInfoNumCrashFilesAvail 1.3.6.1.4.1.4491.2.1.30.1.1.1.1.3
This attribute provides the number of crash files.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdDevIdentificationTable 1.3.6.1.4.1.4491.2.1.30.1.1.2
This table provides data that uniquely identifies the RPD.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdDevIdentificationEntry

docsRphyRpdDevIdentificationEntry 1.3.6.1.4.1.4491.2.1.30.1.1.2.1
The conceptual row of docsRphyRpdDevIdentificationTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdDevIdentificationEntry  

docsRphyRpdDevIdVendorName 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.1
This attribute identifies the RPD manufacturer. The format is vendor proprietary.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdDevIdVendorId 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.2
This attribute is the IANA-assigned SMI Network Management Private Enterprise Code of the vendor, as specified in RFC 5612.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevIdModelNum 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.3
This attribute is the model name and number used by the vendor to identify the RPD. The format is vendor proprietary.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdDevIdSerialNum 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.4
This attribute is the serial number of the RPD. The format is vendor proprietary.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..16)  

docsRphyRpdDevIdDeviceAlias 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.5
This attribute reports the device name assigned by the operator and represents a 'handle' for the RPD.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdDevIdDeviceDescr 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.6
This attribute is a short text description of the RPD provided by the RPD manufacturer.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdDevIdHwRev 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.7
This attribute is the revision number of the hardware of the RPD. The format is vendor proprietary.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdDevIdCurrSwVer 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.8
This attribute is the version number of the software currently running on the RPD. The format is vendor proprietary.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdDevIdBootRomVer 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.9
This attribute reports the version number of the boot ROM currently installed on the RPD. The format is vendor proprietary.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdDevIdUsBurstRcvrVendorId 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.10
This attribute reports the IANA-assigned SMI Network Management Private Enterprise Code of the RPD's US burst receiver manufacturer, as specified in RFC 5612.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevIdUsBurstRcvrModelNum 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.11
This attribute reports the model number used by the vendor to identify the RPD's US burst receiver. The format is vendor proprietary.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(3..16)  

docsRphyRpdDevIdUsBurstRcvrDrivVer 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.12
This attribute reports the driver version of the RPD's US burst receiver. The format is vendor proprietary.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(3..16)  

docsRphyRpdDevIdUsBurstRcvrSerialNum 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.13
This attribute reports the serial number of the RPD's US burst receiver. The format is vendor proprietary.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(5..16)  

docsRphyRpdDevIdRcpProtocolVer 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.14
This attribute reports the version of the RCP protocol supported by the RPD.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(3..32)  

docsRphyRpdDevIdRcpSchemaVer 1.3.6.1.4.1.4491.2.1.30.1.1.2.1.15
This attribute reports the version of the RCP schema supported by the RPD.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(5..32)  

docsRphyRpdDevLocationTable 1.3.6.1.4.1.4491.2.1.30.1.1.3
This table provides location details for the RPD. The values are populated via a management interface or other automatic mechanisms (e.g. GPS).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdDevLocationEntry

docsRphyRpdDevLocationEntry 1.3.6.1.4.1.4491.2.1.30.1.1.3.1
The conceptual row of docsRphyRpdDevLocationTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdDevLocationEntry  

docsRphyRpdDevLocationDescr 1.3.6.1.4.1.4491.2.1.30.1.1.3.1.1
This attribute is short text description of where the RPD has been installed, such as a street address. The format is specific to the operator.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..255)  

docsRphyRpdDevLocationLatitude 1.3.6.1.4.1.4491.2.1.30.1.1.3.1.2
This attribute is the latitudinal coordinate of the RPD location, expressed as a 6-byte long string as described in ISO 6709-2008 (6 digit degrees, minutes, seconds: +/-DDMMSS.S). For example: -750015.1
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(9)  

docsRphyRpdDevLocationLongitude 1.3.6.1.4.1.4491.2.1.30.1.1.3.1.3
This attribute is the longitudinal coordinate of the RPD location, expressed as a 7-byte long string as described in ISO 6709-2008 (7 digits degrees, minutes, seconds: +/-DDDMMSS.S). For example: -0750015.1
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(10)  

docsRphyRpdDevCoresConnectedTable 1.3.6.1.4.1.4491.2.1.30.1.1.4
This table provides a list of CCAP-Cores to which the RPD is authenticated, including the CCAP-Core on which the MIB is polled. For each CCAP-Core entry, the RPD indicates if that CCAP-Core is the principal Core. These values are provided by the CCAP-Core on initialization.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdDevCoresConnectedEntry

docsRphyRpdDevCoresConnectedEntry 1.3.6.1.4.1.4491.2.1.30.1.1.4.1
The conceptual row of docsRphyRpdDevCoresConnectedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdDevCoresConnectedEntry  

docsRphyRpdDevCoresConnectedCoreId 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.1
This attribute provides the MAC address of the CCAP-Core identified in the row entry and acts as a key.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

docsRphyRpdDevCoresConnectedAddressType 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.2
This attribute specifies the IP address type for docsRphyRpdDevCoresConnectedAddress.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

docsRphyRpdDevCoresConnectedAddress 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.3
This attribute provides the IPv4 or IPv6 address of the CCAP-Core.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

docsRphyRpdDevCoresConnectedIsPrincipal 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.4
This attribute indicates if the CCAP-Core is the principal core. If true, this attribute indicates that this CCAP-Core is the principal core.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

docsRphyRpdDevCoresConnectedName 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.5
This attribute provides the name of the CCAP-Core as conveyed to the RPD.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdDevCoresConnectedVendorId 1.3.6.1.4.1.4491.2.1.30.1.1.4.1.6
This attribute provides the IANA-assigned SMI Network Management Private Enterprise Code of the vendor, as specified in RFC 1700.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevCapabilitiesTable 1.3.6.1.4.1.4491.2.1.30.1.1.5
This table provides information about the principal capabilities and constraints of the RPD.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdDevCapabilitiesEntry

docsRphyRpdDevCapabilitiesEntry 1.3.6.1.4.1.4491.2.1.30.1.1.5.1
The conceptual row of docsRphyRpdDevCapabilitiesTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdDevCapabilitiesEntry  

docsRphyRpdDevCapabNumDsPorts 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.1
This attribute provides the number of downstream unidirectional RF ports available on the RPD.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevCapabNumUsPorts 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.2
This attribute provides the number of upstream unidirectional RF ports available on the RPD.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevCapabNumTenGeNsPorts 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.3
This attribute provides the number of 10 Gigabit Ethernet ports supported by the RPD.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevCapabNumOneGeNsPorts 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.4
This attribute provides the number 1 Gigabit Ethernet ports supported by the RPD.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevCapabNumDsScQamChans 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.5
This attribute provides the number of downstream SC-QAM channels supported per downstream RF port.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevCapabNumDsOfdmChans 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.6
This attribute provides the number of downstream DOCSIS 3.1 channels supported per downstream RF port.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevCapabNumUsScQamChans 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.7
This attribute provides the number of upstream SC-QAM channels supported per upstream RF port.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevCapabNumUsOfdmaChans 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.8
This attribute provides the number of upstream DOCSIS 3.1 channels supported per upstream RF port.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevCapabNumDsOob55d1Chans 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.9
This attribute provides the number of downstream SCTE 55-1 channels supported per downstream RF port.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevCapabNumUsOob55d1Chans 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.10
This attribute provides the number of upstream SCTE 55-1 channels supported per upstream RF port.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevCapabNumDsOob55d2Modules 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.11
This attribute provides the number of SCTE 55-2 modules supported.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevCapabNumUsOob55d2Demods 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.12
This attribute provides the number of upstream demodulators per SCTE 55-2 modules supported.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevCapabNumNdfChans 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.13
This attribute provides the number of narrowband digital forward channels supported per downstream RF port.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevCapabNumNdrChans 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.14
This attribute provides the number of narrowband digital return channels supported per upstream RF port.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevCapabNumDsPspFlowsPerChan 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.15
This attribute provides the number of distinct PSP flows supported by the RPD on downstream data pseudowires.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

docsRphyRpdDevCapabNumUsPspFlowsPerChan 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.16
This attribute provides the number of distinct PSP flows supported by the RPD on upstream data pseudowires.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

docsRphyRpdDevCapabNumAsynchVideoChans 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.17
This attribute provides the number of asynchronous MPEG video channels supported per downstream RF port.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

docsRphyRpdDevCapabNumCwToneGens 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.18
This attribute provides the number of CW tone generators supported per downstream RF port.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

docsRphyRpdDevCapabLowestCwToneFreq 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.19
This attribute provides the lowest frequency supported by the CW tone generators.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdDevCapabHighestCwToneFreq 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.20
This attribute provides the highest frequency supported by the CW tone generators.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdDevCapabMaxCwTonePwr 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.21
This attribute provides the maximum power level supported by the dedicated CW tone generators, expressed in TenthdBmV.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevCapabQamAsPilot 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.22
This attribute indicates if a QAM channel can be configured as a CW tone. A value of true indicates a QAM channel can be configured as a CW tone. A value of false indicates a QAM channel cannot be configured as a CW tone.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

docsRphyRpdDevCapabSupportsUdpEncap 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.23
This attribute reports whether the RPD supports UDP encapsulation on L2TPv3 pseudowires. A value of true indicates the RPD supports UDP encapsulation on L2TPv3 pseudowires. A value of false indicates the RPD does not support UDP encapsulation on L2TPv3 pseudowires.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

docsRphyRpdDevCapabSupportsFlowTags 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.24
This attribute indicates Flow Tags support capability. If the attribute returns a value of true, the RPD supports Flow Tags on OFDMA channels. A Flow Tag is a 32-bit identifier of a MAC hardware resource (typically a Service Flow). The Flow Tag can be assigned to the scheduled SID by the CCAP Core. The RPD provides Flow Tags in UEPI headers for OFDMA channels. If the attribute returns a value of false, the RPD does not support Flow Tags.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

docsRphyRpdDevCapabSupportsFreqTilt 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.25
This attribute indicates Frequency Tilt support capability. If the attribute returns a value of true, the RPD supports Frequency Tilt settings on DS RF Ports. If the attribute returns a value of false, the RPD does not support Frequency Tilt settings.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

docsRphyRpdDevCapabTiltRange 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.26
This attribute indicates the range of tilt settings that the RPD supports.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevCapabBufferDepthMonAlertSupp 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.27
This attribute indicates buffer depth monitoring alert supported by the RPD. For each bit set to 1, the RPD is capable of monitoring buffer depth on the corresponding types of downstream channels.
Status: current Access: read-only
OBJECT-TYPE    
  BITS ofdmChannels(0), scQamDocsisChannels(1), scQamVideoChannels(2), ndfChannels(3), scte551Channels(4), scte552Channels(5)  

docsRphyRpdDevCapabBufferDepthCfgSupp 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.28
This attribute indicates configuration of the output buffer depth supported by the RPD. This capability is only applicable to DOCSIS downstream channels. For each bit set to 1, the RPD is capable of configuring output buffer depth of the corresponding types of downstream channels.
Status: current Access: read-only
OBJECT-TYPE    
  BITS ofdmChannels(0), scQamDocsisChannels(1)  

docsRphyRpdDevCapabRpdUcdProcTime 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.29
This attribute indicates the minimum interval needed by the RPD to process a UCD message received via GCP. This interval is equivalent to CM UCD processing time defined in MULPIv3.1 but its duration can be longer. The maximum value of the RPD UCD Processing time is 50000 usec. The minimum value RPD UCD Processing time is equal to CM UCD processing time (1500 usec for each changed SC-QAM channel or 2000 usec for each changed upstream OFDMA channel) defined in MULPIv3.1.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevCapabRpdUcdChgNullGrtTime 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.30
This attribute indicates the minimum Null grant interval needed by the RPD in the first MAP with incremented UCD change count. The RPD uses the Null grant in the first map to programs registers of its burst receiver during this interval. The maximum value of the RPD UCD Change Null Grant Time is 4000 usec for each changed channel. The minimum value of the RPD UCD Change Null Grant Time is defined in MULPIv3.1.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevCapabMultiSectionTimingMerRep 1.3.6.1.4.1.4491.2.1.30.1.1.5.1.31
This attribute indicates whether the RPD supports Multi-Section Timing and MER reporting as opposed to just reporting a single average Timing and MER. More detail is documented in the UEPI Probe Pseudowire format of R-UEPI. notSupported: The RPD does not support Multi-Section Timing and MER Reporting supportType1: The RPD supports equally spaced non-overlapping sections supportType2: The RPD supports fully flexible sections and spacing of non-overlapping sections.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER notSupported(0), supportType1(1), supportType2(2)  

docsRphyRpdDevChanReachabilityTable 1.3.6.1.4.1.4491.2.1.30.1.1.6
This table provides RPD channel reachability constraints. In some RPD implementations, an Ethernet interface might not have connectivity to all channels on a port of the RPD. This table is only populated if reachability constraints exist on the RPD.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdDevChanReachabilityEntry

docsRphyRpdDevChanReachabilityEntry 1.3.6.1.4.1.4491.2.1.30.1.1.6.1
The conceptual row of docsRphyRpdDevChanReachabilityTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdDevChanReachabilityEntry  

docsRphyRpdDevChanReachabilityEnetPortIndex 1.3.6.1.4.1.4491.2.1.30.1.1.6.1.1
This attribute identifies the Ethernet port on the RPD that has the connectivity constraint.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..255  

docsRphyRpdDevChanReachabilityRfPortIndex 1.3.6.1.4.1.4491.2.1.30.1.1.6.1.2
This attribute identifies the RF port with which the Ethernet port has a connectivity constraint.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..255  

docsRphyRpdDevChanReachabilityChanType 1.3.6.1.4.1.4491.2.1.30.1.1.6.1.3
This attribute identifies the type of channel that is supported within the specified channel index range on this RF port from the specified Ethernet interface. A row entry will be created for each channel type with a constraint. Absence of a row for a channel type means there is no constraint for that channel type.
Status: current Access: not-accessible
OBJECT-TYPE    
  RphyChannelType  

docsRphyRpdDevChanReachabilityStartChanIndex 1.3.6.1.4.1.4491.2.1.30.1.1.6.1.4
This attribute identifies the first channel of the specified channel type in the range of channels that does not have connectivity to the specified Ethernet port.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..255  

docsRphyRpdDevChanReachabilityEndChanIndex 1.3.6.1.4.1.4491.2.1.30.1.1.6.1.5
This attribute identifies the last channel of the specified channel type in the range of channels that does not have connectivity to the specified Ethernet port.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

docsRphyRpdDevDsUsRfPortAllocTable 1.3.6.1.4.1.4491.2.1.30.1.1.7
This table provides the allocation status for the downstream channel resources on the RPD on a per DS RF port basis as well as for the upstream channel resources on a per US RF port basis.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdDevDsUsRfPortAllocEntry

docsRphyRpdDevDsUsRfPortAllocEntry 1.3.6.1.4.1.4491.2.1.30.1.1.7.1
The conceptual row of docsRphyRpdDevDsUsRfPortAllocTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdDevDsUsRfPortAllocEntry  

docsRphyRpdDevDsUsRfPortAllocIndex 1.3.6.1.4.1.4491.2.1.30.1.1.7.1.1
This attribute provides the index of the downstream or upstream RF port for which resource allocation is being reported.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..255  

docsRphyRpdDevDsUsRfPortAllocDirection 1.3.6.1.4.1.4491.2.1.30.1.1.7.1.2
This attribute indicates whether the allocation applies to the upstream or downstream RF Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  IfDirection  

docsRphyRpdDevDsUsRfPortAllocScQamChans 1.3.6.1.4.1.4491.2.1.30.1.1.7.1.3
This attribute provides the number of allocated SC-QAM channels on this RF port.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevDsUsRfPortAllocOfdmChans 1.3.6.1.4.1.4491.2.1.30.1.1.7.1.4
This attribute provides the number of allocated DOCSIS 3.1 channels on this RF port.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevDsUsRfPortAllocOob551Chans 1.3.6.1.4.1.4491.2.1.30.1.1.7.1.5
This attribute provides the number of allocated SCTE 55-1 channels on this RF port.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevDsUsRfPortAllocNdChans 1.3.6.1.4.1.4491.2.1.30.1.1.7.1.6
This attribute provides the number of allocated narrowband digital forward channels (for DS RF Ports) or narrowband digital return channels (for US RF Ports) on this RF port.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdDevL2tpSessionInfoTable 1.3.6.1.4.1.4491.2.1.30.1.1.8
This table provides details about each tunnel session between the RPD and each CCAP Core with which the RPD is associated from the RPD's point of view The attributes in this table are used to create an entry for each L2TPv3 tunnel (session) terminated at an R-PHY entity (RPD).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdDevL2tpSessionInfoEntry

docsRphyRpdDevL2tpSessionInfoEntry 1.3.6.1.4.1.4491.2.1.30.1.1.8.1
The conceptual row of docsRphyRpdDevL2tpSessionInfoTable. A row entry is created for every session the RPD terminates and there may be entries for sessions with different CCAP-Cores if the RPD is connected with one or more auxiliary cores.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdDevL2tpSessionInfoEntry  

docsRphyRpdDevL2tpSessionInfoLocalLcceIpAddrType 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.1
This attribute indicates whether the IP address provide in docsRphyRpdDevL2tpSessionInfoLocalLcceIpAddr is IPv4 or IPv6.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

docsRphyRpdDevL2tpSessionInfoLocalLcceIpAddr 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.2
This attribute provides the local LCCE IP address on the RPD of the session detailed in the row entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

docsRphyRpdDevL2tpSessionInfoLocalId 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.3
This attribute provides the value of the session ID assigned to the session by the RPD.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdDevL2tpSessionInfoRemoteLcceIpAddrType 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.4
This attribute indicates whether the IP address provide in docsRphyRpdDevL2tpSessionInfoRemoteLcceIpAddr is IPv4 or IPv6.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

docsRphyRpdDevL2tpSessionInfoRemoteLcceIpAddr 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.5
This attribute provides the remote-side LCCE IP address of the session detailed in the row entry.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

docsRphyRpdDevL2tpSessionInfoRemoteId 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.6
This attribute provides the value of the session ID assigned to the session by the remote peer (RPD).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdDevL2tpSessionInfoCoreId 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.7
This attribute provides the MAC address of the CCAP Core with which this session terminates. The CCAP Core sends its MAC address to the RPD periodically via the DOCSIS SYNC MAC Message in the Source Address field.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

docsRphyRpdDevL2tpSessionInfoConnCtrlID 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.8
This attribute indicates the control connection identifier (CCID) for this session.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdDevL2tpSessionInfoUdpPort 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.9
This attribute provides the UDP Port reported by the RPD when the DEPI session uses L2TPv3 Header Over UDP. This attribute reports a value of 0 when the session is running with the L2TPv3 Session IP Header. This port number is negotiated between the CCAP Core and the RPD according to the L2TPv3 RFC.
Status: current Access: read-only
OBJECT-TYPE    
  InetPortNumber  

docsRphyRpdDevL2tpSessionInfoDescr 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.10
This attribute provides an ASCII string constructed with the form: RemoteEndId=(pp:mmm:ccc), ... { repeated for multiple endpoints } where pp is the 0-based port num signaled in the RemoteEndId AVP mmm is the channel-type enum value from the RemoteEndId AVP ccc is the channel number from the RemoteEndId AVP.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdDevL2tpSessionInfoSessionType 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.11
This attribute specifies whether the session is an MPT session or PSP session.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER psp(1), mpt(2)  

docsRphyRpdDevL2tpSessionInfoSessionSubType 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.12
This attribute specifies the type of DEPI MPT or DEPI PSP session.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER mptLegacy(1), pspLegacy(2), mcm(3), pspDepiMultichannel(4), pspUepiScQam(5), pspUepiOfdma(6), pspBwReqScQam(7), pspBwReqOfdma(8), pspProbe(9), pspRngReqScQam(10), pspRngReqOfdma(11), pspMapScQam(12), pspMapOfdma(13), pspSpecman(14), pspPnm(15), psp551Fwd(16), psp551Ret(17), psp552Fwd(18), psp552Ret(19), pspNdf(20), pspNdr(21)  

docsRphyRpdDevL2tpSessionInfoMaxPayload 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.13
This attribute indicates the maximum MTU negotiated between the CCAP Core and the RPD during the session establishment process. It considers the header subtractions as indicated in the DEPI specification.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdDevL2tpSessionInfoPathPayload 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.14
This attribute indicates the maximum MTU traversing the CIN from CCAP Core to the RPD. This is calculated by the CCAP Core by procedures such as MTU discovery as described in the DEPI specification.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdDevL2tpSessionInfoRpdIfMtu 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.15
This attribute provides the RPD's CIN interface MTU and is read as the value of the following L2TPV3 AVP transmitted by the RPD during session setup: DEPI Downstream PW UEPI Upstream PW DEPI Remote MTU AVP (ICRP) UEPI Remote MTU AVP (ICRP).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdDevL2tpSessionInfoCoreIfMtu 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.16
This attribute provides the CCAP Core's CIN interface MTU and is read as the value of the following L2TPv3 AVP as received by the device during session setup: DEPI Downstream PW UEPI Upstream PW DEPI Local MTU AVP (ICRQ) UEPI Local MTU AVP (ICRQ).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdDevL2tpSessionInfoErrorCode 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.17
The error code raised when the session is in an error state. 'invalidMACInterfaceValue' Indicates wrong assignment of the CCAP Core MAC interface ifIndex. 'invalidInterfaceValue' Indicates wrong assignment of the CCAP Core Downstream interface ifIndex 'noResourcesForInterfaceIfIndex' Indicates the CCAP Core has no more resources to assign a session to this entry. 'l2tpv3Error' An L2TPv3 StopCCN or CDN message was issued 'ifAdminStatusSetToDown' Indicates the ifAdminStatus was set to down and the session was torn down.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), invalidMACInterfaceValue(2), invalidInterfaceValue(3), noResourcesForInterfaceIndex(4), l2tpv3Error(5), ifAdminStatusSetToDown(6)  

docsRphyRpdDevL2tpSessionInfoCreationTime 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.18
The attribute contains the sysUptime when the entry was turned active.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

docsRphyRpdDevL2tpSessionInfoOperStatus 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.19
This attribute provides the current status of the pseudowire from the point of view of the specific reporting entity (RPD). Values are as follows: 'other' indicates a vendor-specific operational status. 'up' indicates that the pseudowire is ready to pass packets. 'down' indicates that pseudowire signaling is not yet finished, or indications available at the service level indicate that the pseudowire is not passing packets. 'testing' indicates that AdminStatus at the pseudowire level is set to test. 'dormant' indicates that the pseudowire is not in a condition to pass packets but is in a 'pending' state, waiting for some external event. 'notPresent' indicates that some component is missing to accomplish the setup of the pseudowire. It can be a configuration error, incomplete configuration, or a missing H/W component. 'lowerLayerDown' indicates one or more of the lower-layer interfaces responsible for running the underlying PSN is not in OperStatus 'up' state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), up(2), down(3), testing(4), dormant(5), notPresent(6), lowerLayerDown(7)  

docsRphyRpdDevL2tpSessionInfoLocalStatus 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.20
The attribute provides the status of the pseudowire in the local node. If the 'other' bit is set, it indicates that an additional vendor-specific status is reported. If none of the bits are set, it indicates no faults are reported.
Status: current Access: read-only
OBJECT-TYPE    
  BITS other(0), pwNotForwarding(1), servicePwRxFault(2), servicePwTxFault(3), psnPwRxFault(4), psnPwTxFault(5)  

docsRphyRpdDevL2tpSessionInfoLastChange 1.3.6.1.4.1.4491.2.1.30.1.1.8.1.21
The attribute provides the value of sysUpTime when the session entered its current OperStatus state from the point of view of the specific reporting entity (RPD).
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

docsRphyRpdDevL2tpSessionStatsTable 1.3.6.1.4.1.4491.2.1.30.1.1.9
This table provides statistics about each tunnel session between the RPD and each CCAP Core with which the RPD is associated from the RPD's point of view.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdDevL2tpSessionStatsEntry

docsRphyRpdDevL2tpSessionStatsEntry 1.3.6.1.4.1.4491.2.1.30.1.1.9.1
The conceptual row of docsRphyRpdDevL2tpSessionStatsTable. This table is an augmentation of docsRphyL2tpSessionInfoTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdDevL2tpSessionStatsEntry  

docsRphyRpdDevL2tpSessionStatsOutOfSeqPkts 1.3.6.1.4.1.4491.2.1.30.1.1.9.1.1
This attribute indicates the count of session packets that were received out of sequence from the point of view of the reporting entity. It is vendor dependent the re-sequence of packets. Implementations that do not re-sequence packets also increase the value of ifInDiscards for the respective entry.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

docsRphyRpdDevDiagStatusTable 1.3.6.1.4.1.4491.2.1.30.1.1.10
This table reports information about an RPD's diagnostic self test results.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdDevDiagStatusEntry

docsRphyRpdDevDiagStatusEntry 1.3.6.1.4.1.4491.2.1.30.1.1.10.1
The conceptual row of docsRphyRpdDevDiagStatusTable. This table returns at least one row indicating pass or failure for the diagnostic self test.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdDevDiagStatusEntry  

docsRphyRpdDevDiagStatusProbableCause 1.3.6.1.4.1.4491.2.1.30.1.1.10.1.1
This attribute reports the probable cause of the diagnostic test error condition. Probable causes may be related to: - Communications error - Quality of Service error - Processing error - Equipment error - Environmental error The format for values returned are vendor-specific. When the self test result is a pass, this attribute returns 'Self Test Passed'.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdDevDiagStatusAdditionalText 1.3.6.1.4.1.4491.2.1.30.1.1.10.1.2
This attribute reports a free form text description of the diagnostic test error condition. This provides supplemental information for the ProbableCause. When the self test result is a pass, this attribute returns 'No errors found'.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdDevDiagStatusSeverityLevel 1.3.6.1.4.1.4491.2.1.30.1.1.10.1.3
This attribute reports the severity level for the diagnostic test error condition. Severity levels are based on the DOCSIS event priority levels. When the self test result is a pass, this attribute returns 'information'.
Status: current Access: read-only
OBJECT-TYPE    
  RphyEventSeverityType  

docsRphyRpdDevDepiMcastSessionTable 1.3.6.1.4.1.4491.2.1.30.1.1.11
This table reports the DEPI IP multicast sessions currently joined by an RPD.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdDevDepiMcastSessionEntry

docsRphyRpdDevDepiMcastSessionEntry 1.3.6.1.4.1.4491.2.1.30.1.1.11.1
The conceptual row of docsRphyRpdDevDepiMcastSessionTable. A row entry of this table represents one DEPI IP Multicast session replicated to one RPD. The indexing provides the RPD unique identifier and the (S,G) IP address pair that uniquely identifies an IP multicast session. The CCAP Core creates a row entry when it confirms an RPD has joined a DEPI IP multicast session. The CCAP Core deletes the row entry when it confirms an RPD has left the DEPI IP multicast session or disconnects its GCP session with the CCAP Core.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdDevDepiMcastSessionEntry  

docsRphyRpdDevDepiMcastSessionIpAddrType 1.3.6.1.4.1.4491.2.1.30.1.1.11.1.1
This key attribute reports whether the IP addresses provided in GroupIpAddr, SourceIpAddr, LocalLcceIpAddr and RemoteLcceIpAddr are IPv4 or IPv6.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

docsRphyRpdDevDepiMcastSessionGrpIpAddr 1.3.6.1.4.1.4491.2.1.30.1.1.11.1.2
This key attribute reports the group (destination) address of an IP multicast session transmitted via DEPI multicast.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

docsRphyRpdDevDepiMcastSessionSrcIpAddr 1.3.6.1.4.1.4491.2.1.30.1.1.11.1.3
For Source Specific Multicast (SSM), this key attribute reports the source IP address of an IP multicast session transmitted via DEPI multicast. For Any-Source Multicast (ASM) sessions, this attribute reports the all-0s IP address.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

docsRphyRpdDevDepiMcastSessionLocalLcceIpAddr 1.3.6.1.4.1.4491.2.1.30.1.1.11.1.4
This attribute reports the RPD local LCCE IP address of the L2TPv3 DEPI control session that instructed the RPD to join the IP multicast session.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

docsRphyRpdDevDepiMcastSessionRemoteLcceIpAddr 1.3.6.1.4.1.4491.2.1.30.1.1.11.1.5
This attribute reports the RPD remote LCCE IP address (i.e. on the CCAP Core) of the L2TPv3 control session that instructed the RPD to join the IP multicast session.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

docsRphyRpdDevDepiMcastSessionId 1.3.6.1.4.1.4491.2.1.30.1.1.11.1.6
This attribute reports the L2TPv3 Session ID assigned by the CCAP Core to the DEPI IP multicast session. The value is assigned according to the referenced specification in the range 0x80000001 through 0x8000FFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 2147483649..2147549183  

docsRphyRpdDevDepiMcastSessionJoinTime 1.3.6.1.4.1.4491.2.1.30.1.1.11.1.7
This attribute reports the last time the RPD has joined this session.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

docsRphyRpdDevEventLogTable 1.3.6.1.4.1.4491.2.1.30.1.1.12
This table reports event log information for an RPD.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdDevEventLogEntry

docsRphyRpdDevEventLogEntry 1.3.6.1.4.1.4491.2.1.30.1.1.12.1
The conceptual row of docsRphyRpdDevEventLogTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdDevEventLogEntry  

docsRphyRpdDevEventLogIndex 1.3.6.1.4.1.4491.2.1.30.1.1.12.1.1
This key attribute provides relative ordering of the events in the event log. This attribute will always increase except when (a) the log is reset (b) the device reboots and does not implement non-volatile storage for this log, or (c) it reaches the value 2^31. The next entry for all the above cases is 1.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdDevEventLogFirstTime 1.3.6.1.4.1.4491.2.1.30.1.1.12.1.2
This attribute provides the local RPD time when this event was created.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

docsRphyRpdDevEventLogLastTime 1.3.6.1.4.1.4491.2.1.30.1.1.12.1.3
When an event reports only one event occurrence, this attribute will have the same value as the corresponding instance of FirstTime. When an event reports multiple event occurrences, this attribute will record the local RPD time when the most recent occurrence for this event occurred.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

docsRphyRpdDevEventLogCounts 1.3.6.1.4.1.4491.2.1.30.1.1.12.1.4
This attribute provides the number of consecutive event occurrences reported by this event. This starts at 1 with the creation of this event occurrence and increments by 1 for each subsequent duplicate event occurrence.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

docsRphyRpdDevEventLogLevel 1.3.6.1.4.1.4491.2.1.30.1.1.12.1.5
This attribute provides the priority level of this event, as defined by Annex B. These are ordered from most serious (emergency) to least serious (debug).
Status: current Access: read-only
OBJECT-TYPE    
  RphyEventSeverityType  

docsRphyRpdDevEventLogId 1.3.6.1.4.1.4491.2.1.30.1.1.12.1.6
This attribute provides the identifier of this event, as defined by Annex B.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdDevEventLogText 1.3.6.1.4.1.4491.2.1.30.1.1.12.1.7
This attribute provides the message text of this event, as defined by Annex B.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdDevOob551UsChanStatusTable 1.3.6.1.4.1.4491.2.1.30.1.1.13
This table provides per-RPD counts of upstream SCTE 55-1 cells sent to a Network Controller.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdDevOob551UsChanStatusEntry

docsRphyRpdDevOob551UsChanStatusEntry 1.3.6.1.4.1.4491.2.1.30.1.1.13.1
The conceptual row of docsRphyRpdDevOob551UsChanStatusTable. A row entry of this table represents counts that are updated by the CCAP Core, which parses each upstream SCTE 55-1 packet and uses the power level and packet status (which are really cell status) bits in those packets to determine how to update the counters.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdDevOob551UsChanStatusEntry  

docsRphyRpdDevOob551UsChanStatusRfPort 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.1
This key attribute reports the RPD RF port number carrying this SCTE 55-1 US channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdDevOob551UsChanStatusChannelId 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.2
This key attribute reports the demodulator ID (channel number) for this SCTE 55-1 US channel.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdDevOob551UsChanStatusNcIpAddrType 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.3
This attribute indicates whether the IP address provide in docsRphyRpdDevOob551UsChanStatusNcIpAddr is IPv4 or IPv6.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

docsRphyRpdDevOob551UsChanStatusNcIpAddr 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.4
This attribute reports the IP host address of the Network Controller receiving the cells on this SCTE 55-1 US channel.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

docsRphyRpdDevOob551UsChanStatusArpdSrcIpAddrType 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.5
This attribute indicates whether the IP address provide in docsRphyRpdDevOob551UsChanStatusArpdSrcIpAddr is IPv4 or IPv6.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

docsRphyRpdDevOob551UsChanStatusArpdSrcIpAddr 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.6
This attribute reports the virtual ARPD source IP host address used when sending cells to the Network Controller.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

docsRphyRpdDevOob551UsChanStatusPerfectCellsRcvd 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.7
This attribute reports the number of perfect cells received by the demodulator for this SCTE 55-1 US channel. Perfect cells have status 0 in the US SCTE 55-1 OOB packet.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdDevOob551UsChanStatusCorrectedCellsRcvd 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.8
This attribute reports the number of errored cells received by the demodulator for this SCTE 55-1 US channel that were successfully corrected. Corrected cells have status 1 in the US SCTE 55-1 OOB packet.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdDevOob551UsChanStatusUncorrectableCellsRcvd 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.9
This attribute reports the number of errored cells received by the demodulator for this SCTE 55-1 US channel that could not be corrected. Uncorrectable cells have status 3 in the US SCTE 55-1 OOB packet.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdDevOob551UsChanStatusTotalCellsRcvd 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.10
This attribute reports the total of all cells received for this SCTE 55-1 US channel.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdDevOob551UsChanStatusPwrLevel 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.11
This attribute reports the average power level from nominal of all received MAC Cells by the demodulator for this upstream SCTE 55-1 channel in tenths of a dB. The six power level bits 1 in the US SCTE 55-1 OOB packet report the nominal power per cell in units of 0.5 dB.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

docsRphyRpdDevOob551UsChanStatusMaxPwrLevel 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.12
This attribute reports the maximum power level from nominal of all received MAC Cells by the demodulator for this upstream SCTE 55-1 channel in tenths of a dB.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

docsRphyRpdDevOob551UsChanStatusMinPwrLevel 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.13
This attribute reports the minimum power level from nominal of all received MAC Cells by the demodulator for this upstream SCTE 55-1 channel in tenths of a dB.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

docsRphyRpdDevOob551UsChanStatusCounterDiscontinuityTime 1.3.6.1.4.1.4491.2.1.30.1.1.13.1.14
TThis attribute reports the value of sysUpTime on the most recent occasion at which any one or more of this interface's counters suffered a discontinuity. If no such discontinuities have occurred since the last re-initialization of the local management subsystem, then this attribute reports a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

docsRphyRpdDevCrashDataFileStatusTable 1.3.6.1.4.1.4491.2.1.30.1.1.14
This table provides status information for the crash analysis data files.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdDevCrashDataFileStatusEntry

docsRphyRpdDevCrashDataFileStatusEntry 1.3.6.1.4.1.4491.2.1.30.1.1.14.1
The conceptual row of docsRphyRpdDevCrashDataFileStatusTable. A row entry of this table represents a file that is available in the device for upload or for which an upload is in progress.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdDevCrashDataFileStatusEntry  

docsRphyRpdDevCrashDataFileStatusIndex 1.3.6.1.4.1.4491.2.1.30.1.1.14.1.1
This key attribute uniquely identifies a crash analysis file.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdDevCrashDataFileStatusFilename 1.3.6.1.4.1.4491.2.1.30.1.1.14.1.2
This attribute contains the name of the crash analysis file, stored in the device that is available to be uploaded to the server. Filenames are defined by the application that creates them. The RPD SHOULD generate crash analysis files with names which include RPD's unique id and a timestamp. The timestamp indicates the time when the crash has occurred with granularity of one second. The RPD SHOULD format the timestamp in the form 'Unix time', which is defined as the number of seconds that have elapsed since midnight Coordinated Universal Time (UTC), Thursday, 1 January 1970. For example, a crash file name 'RPD_crash_dump_id_00000187ADF_time_1403405123' indicates that the file was generated by RPD with Unique ID of 00.00.00.18.7A.DF on Sunday 22nd June 2014 02:45:23 AM.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(1..255)  

docsRphyRpdDevCrashDataFileStatusFileStatus 1.3.6.1.4.1.4491.2.1.30.1.1.14.1.3
This attribute reflects the status of the crash data file. The possible values are listed below. other(1) - Any condition not covered by the other defined values. availableForUpload(2) - The file is available to be uploaded. uploadInProgress(3) - The file is currently being uploaded. The file is not available for another upload in this state. uploadCompleted(4) - The file was successfully uploaded. The file is available for another upload. uploadPending(5) - The file has been selected for upload but a condition does not allow the upload to take place. The upload will start when the condition blocking uploads has been removed. For example, another upload that is currently in progress could cause this value to be returned. uploadPending status can also indicate a situation where the RPD is waiting to retry the upload after the initial attempt(s) has failed. The file is not available for another upload in this state. uploadCancelled(6) - An upload was cancelled before it completed. The file is available for another upload. error(7) - An error occurred and the file was not successfully uploaded. The file is available for another upload.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), availableForUpload(2), uploadInProgress(3), uploadCompleted(4), uploadPending(5), uploadCancelled(6), error(7)  

docsRphyRpdDevUsSignalQualityTable 1.3.6.1.4.1.4491.2.1.30.1.1.15
This table provide individual upstream signal quality values for RPDs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdDevUsSignalQualityEntry

docsRphyRpdDevUsSignalQualityEntry 1.3.6.1.4.1.4491.2.1.30.1.1.15.1
The conceptual row of docsRphyRpdDevUsSignalQualityTable. A row entry of this table represents the upstream signal quality values of a single RPD
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdDevUsSignalQualityEntry  

docsRphyRpdDevUsSignalQualityRfPort 1.3.6.1.4.1.4491.2.1.30.1.1.15.1.1
This key attribute reports the RPD RF port number carrying this US channel. This corresponds to the attribute RpdUsRfPortNum of the RpdUsRfPortRef object in the configuration Information Model.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdDevUsSignalQualityChannelIfIndex 1.3.6.1.4.1.4491.2.1.30.1.1.15.1.2
This attribute corresponds to the ifIndex of the Upstream Physical Channel of the CCAP Core for this US channel. Note that with upstream virtual combining, this attribute corresponds to the same CCAP Core ifIndex for different RPD unique Ids.
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

docsRphyRpdDevUsSignalQualityRxMer 1.3.6.1.4.1.4491.2.1.30.1.1.15.1.3
This attribute reports an in-channel received average Modulation Error Ratio (MER). An RxMER sample is defined as an estimate, provided by the demodulator, of the ratio: (average constellation energy with equally likely symbols) / (average squared magnitude of error vector) RxMER is measured just prior to FEC (trellis/Reed-Solomon) decoding. RxMER includes the effects of the HFC channel as well as implementation effects of the modulator and demodulator. Error vector estimation may vary among demodulator implementations. The CCAP Core RxMER is averaged over a given number of bursts at the burst receiver, which may correspond to transmissions from multiple users. In the case of S-CDMA mode, RxMER is measured on the de-spread signal. For OFDMA channels, this attribute always reports 0.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -2147483648..2147483647  

docsRphyRpdDevUsSignalQualityRxMerSamples 1.3.6.1.4.1.4491.2.1.30.1.1.15.1.4
This attribute reports RxMerSamples which is a statistically significant number of bursts for the CCAP Core, processed to arrive at the RxMER value. For the CCAP Core, the MER measurement includes only valid bursts that are not in contention regions. For OFDMA channels, this attribute always reports 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdDevUsSignalQualityUnerroreds 1.3.6.1.4.1.4491.2.1.30.1.1.15.1.5
This attribute reports the count of codewords received on this channel without error. This includes all codewords, whether or not they were part of frames destined for this device. Reference: OFDMA FEC Error Reporting section of this specification.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdDevUsSignalQualityCorrecteds 1.3.6.1.4.1.4491.2.1.30.1.1.15.1.6
This attribute reports the count of codewords received on this channel with correctable errors. This includes all codewords, whether or not they were part of frames destined for this device. Reference: OFDMA FEC Error Reporting section of this specification.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdDevUsSignalQualityUncorrectables 1.3.6.1.4.1.4491.2.1.30.1.1.15.1.7
This attribute reports the count of codewords received on this channel with uncorrectable errors. This includes all codewords, whether or not they were part of frames destined for this device. Reference: OFDMA FEC Error Reporting section of this specification.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfPhysEntityTable 1.3.6.1.4.1.4491.2.1.30.1.2.1
This table reports entities that exist within each Remote PHY Node that is communicating with the CCAP Core. Because the entities exist within the Remote PHY Nodes and not the CCAP Core, the RPDs communicate this information to the CCAP core via GCP. This object is based on the entPhysicalTable object specified in the ENTITY-MIB from RFC 4133. See the reference for additional requirements.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdIfPhysEntityEntry

docsRphyRpdIfPhysEntityEntry 1.3.6.1.4.1.4491.2.1.30.1.2.1.1
Information about a particular physical entity. Each entry provides objects (docsRphyRpdIfPhysEntityDescr, docsRphyRpdIfPhysEntityVendorType, and docsRphyRpdIfPhysEntityClass) to help an NMS identify and characterize the entry and objects (docsRphyRpdIfPhysEntityContainedIn and docsRphyRpdIfPhysEntityParentRelPos) to help an NMS relate the particular entry to other entries in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdIfPhysEntityEntry  

docsRphyRpdIfPhysEntityIndex 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.1
This key attribute reports an arbitrary value that uniquely identifies the physical entity. Index values for different physical entities are not necessarily contiguous.
Status: current Access: not-accessible
OBJECT-TYPE    
  PhysicalIndex  

docsRphyRpdIfPhysEntityDescr 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.2
A textual description of physical entity. This object should contain a string that identifies the manufacturer's name for the physical entity and should be set to a distinct value for each version or model of the physical entity.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdIfPhysEntityVendorType 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.3
An indication of the vendor-specific hardware type of the physical entity. Note that this is different from the definition of MIB-II's sysObjectID. An agent should set this object to an enterprise-specific registration identifier value indicating the specific equipment type in detail. The associated instance of docsRphyRpdIfPhysEntityClass is used to indicate the general type of hardware device. If no vendor-specific registration identifier exists for this physical entity, or the value is unknown by this agent, then the value { 0 0 } is returned.
Status: current Access: read-only
OBJECT-TYPE    
  AutonomousType  

docsRphyRpdIfPhysEntityContainedIn 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.4
The value of docsRphyRpdIfPhysEntityIndex for the physical entity that 'contains' this physical entity. A value of zero indicates this physical entity is not contained in any other physical entity. Note that the set of 'containment' relationships define a strict hierarchy; that is, recursion is not allowed. In the event that a physical entity is contained by more than one physical entity (e.g., double-wide modules), this object should identify the containing entity with the lowest value of docsRphyRpdIfPhysEntityIndex.
Status: current Access: read-only
OBJECT-TYPE    
  PhysicalIndexOrZero  

docsRphyRpdIfPhysEntityClass 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.5
An indication of the general hardware type of the physical entity. An agent should set this object to the standard enumeration value that most accurately indicates the general class of the physical entity, or the primary class if there is more than one entity. If no appropriate standard registration identifier exists for this physical entity, then the value 'other(1)' is returned. If the value is unknown by this agent, then the value 'unknown(2)' is returned.
Status: current Access: read-only
OBJECT-TYPE    
  IANAPhysicalClass  

docsRphyRpdIfPhysEntityParentRelPos 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.6
An indication of the relative position of this 'child' component among all its 'sibling' components. Sibling components are defined as docsRphyRpdIfPhysEntityEntries that share the same instance values of each of the docsRphyRpdIfPhysEntityContainedIn and docsRphyRpdIfPhysEntityClass objects. An NMS can use this object to identify the relative ordering for all sibling components of a particular parent (identified by the docsRphyRpdIfPhysEntityContainedIn instance in each sibling entry). If possible, this value should match any external labeling of the physical component. For example, for a container (e.g., card slot) labeled as 'slot #3', docsRphyRpdIfPhysEntityParentRelPos should have the value '3'. Note that the docsRphyRpdIfPhysEntityEntry for the module plugged in slot 3 should have an docsRphyRpdIfPhysEntityParentRelPos value of '1'. If the physical position of this component does not match any external numbering or clearly visible ordering, then user documentation or other external reference material should be used to determine the parent-relative position. If this is not possible, then the agent should assign a consistent (but possibly arbitrary) ordering to a given set of 'sibling' components, perhaps based on internal representation of the components. If the agent cannot determine the parent-relative position for some reason, or if the associated value of docsRphyRpdIfPhysEntityContainedIn is '0', then the value '-1' is returned. Otherwise, a non-negative integer is returned, indicating the parent-relative position of this physical entity. Parent-relative ordering normally starts from '1' and continues to 'N', where 'N' represents the highest positioned child entity. However, if the physical entities (e.g., slots) are labeled from a starting position of zero, then the first sibling should be associated with an docsRphyRpdIfPhysEntityParentRelPos value of '0'. Note that this ordering may be sparse or dense, depending on agent implementation. The actual values returned are not globally meaningful, as each 'parent' component may use different numbering algorithms. The ordering is only meaningful among siblings of the same parent component. The agent should retain parent-relative position values across reboots, either through algorithmic assignment or use of non-volatile storage.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -1..2147483647  

docsRphyRpdIfPhysEntityName 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.7
The textual name of the physical entity. The value of this object should be the name of the component as assigned by the local device and should be suitable for use in commands entered at the device's 'console'. This might be a text name (e.g., 'console') or a simple component number (e.g., port or module number, such as '1'), depending on the physical component naming syntax of the device. If there is no local name, or if this object is otherwise not applicable, then this object contains a zero-length string. Note that the value of docsRphyRpdIfPhysEntityName for two physical entities will be the same in the event that the console interface does not distinguish between them, e.g., slot-1 and the card in slot-1.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdIfPhysEntityHardwareRev 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.8
The vendor-specific hardware revision string for the physical entity. The preferred value is the hardware revision identifier actually printed on the component itself (if present). Note that if revision information is stored internally in a non-printable (e.g., binary) format, then the agent must convert such information to a printable format in an implementation-specific manner. If no specific hardware revision string is associated with the physical component, or if this information is unknown to the agent, then this object will contain a zero-length string.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdIfPhysEntityFirmwareRev 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.9
The vendor-specific firmware revision string for the physical entity. Note that if revision information is stored internally in a non-printable (e.g., binary) format, then the agent must convert such information to a printable format in an implementation-specific manner. If no specific firmware programs are associated with the physical component, or if this information is unknown to the agent, then this object will contain a zero-length string.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdIfPhysEntitySoftwareRev 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.10
The vendor-specific software revision string for the physical entity. Note that if revision information is stored internally in a non-printable (e.g., binary) format, then the agent must convert such information to a printable format in an implementation-specific manner. If no specific software programs are associated with the physical component, or if this information is unknown to the agent, then this object will contain a zero-length string.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdIfPhysEntitySerialNum 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.11
The vendor-specific serial number string for the physical entity. The preferred value is the serial number string actually printed on the component itself (if present). On the first instantiation of a physical entity, the value of docsRphyRpdIfPhysEntitySerialNum associated with that entity is set to the correct vendor-assigned serial number, if this information is available to the agent. If a serial number is unknown or non-existent, the docsRphyRpdIfPhysEntitySerialNum will be set to a zero-length string instead. Note that implementations that can correctly identify the serial numbers of all installed physical entities do not need to provide write access to the docsRphyRpdIfPhysEntitySerialNum object. Agents that cannot provide non-volatile storage for the docsRphyRpdIfPhysEntitySerialNum strings are not required to implement write access for this object. Not every physical component will have a serial number, or even need one. Physical entities for which the associated value of the docsRphyRpdIfPhysEntityIsFRU object is equal to 'false(2)' (e.g., the repeater ports within a repeater module) do not need their own unique serial numbers. An agent does not have to provide write access for such entities and may return a zero-length string.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

docsRphyRpdIfPhysEntityMfgName 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.12
The name of the manufacturer of this physical component. The preferred value is the manufacturer name string actually printed on the component itself (if present). Note that comparisons between instances of the docsRphyRpdIfPhysEntityModelName, docsRphyRpdIfPhysEntityFirmwareRev, docsRphyRpdIfPhysEntitySoftwareRev, and the docsRphyRpdIfPhysEntitySerialNum objects are only meaningful amongst docsRphyRpdIfPhysEntityEntries with the same value of docsRphyRpdIfPhysEntityMfgName. If the manufacturer name string associated with the physical component is unknown to the agent, then this object will contain a zero-length string.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdIfPhysEntityModelName 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.13
The vendor-specific model name identifier string associated with this physical component. The preferred value is the customer-visible part number, which may be printed on the component itself. If the model name string associated with the physical component is unknown to the agent, then this object will contain a zero-length string.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdIfPhysEntityAlias 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.14
This object is an 'alias' name for the physical entity, as specified by a network manager, and provides a non-volatile 'handle' for the physical entity. On the first instantiation of a physical entity, the value of docsRphyRpdIfPhysEntityAlias associated with that entity is set to the zero-length string. However, the agent may set the value to a locally unique default value, instead of a zero-length string.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

docsRphyRpdIfPhysEntityAssetID 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.15
This object is a user-assigned asset tracking identifier (as specified by a network manager) for the physical entity and provides non-volatile storage of this information. On the first instantiation of a physical entity, the value of docsRphyRpdIfPhysEntityAssetID associated with that entity is set to the zero-length string. Not every physical component will have an asset tracking identifier or even need one. Physical entities for which the associated value of the docsRphyRpdIfPhysEntityIsFRU object is equal to 'false(2)' (e.g., the repeater ports within a repeater module) do not need their own unique asset tracking identifier. An agent does not have to provide write access for such entities and may instead return a zero-length string. If no asset tracking information is associated with the physical component, then this object will contain a zero-length string.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

docsRphyRpdIfPhysEntityIsFRU 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.16
This object indicates whether or not this physical entity is considered a 'field replaceable unit' by the vendor. If this object contains the value 'true(1)', then this docsRphyRpdIfPhysEntityEntry identifies a field replaceable unit. For all docsRphyRpdIfPhysEntityEntries that represent components permanently contained within a field replaceable unit, the value 'false(2)' should be returned for this object.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

docsRphyRpdIfPhysEntityMfgDate 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.17
This object contains the date of manufacturing of the managed entity. If the manufacturing date is unknown or not supported, the object is not instantiated. The special value '0000000000000000'H may also be returned in this case.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

docsRphyRpdIfPhysEntityUris 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.18
This object contains identification information about the physical entity. The object contains URIs; therefore, the syntax of this object must conform to RFC 3986, Section 3. Multiple URIs may be present and are separated by white space characters. Leading and trailing white space characters are ignored. If no URI identification information is known about the physical entity, the object is not instantiated. A zero-length octet string may also be returned in this case.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

docsRphyRpdIfPhysEntityUUID 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.19
This object contains identification information about the physical entity. The object contains a Universally Unique Identifier, the syntax of this object must conform to RFC 4122, Section 4.1. A zero-length octet string is returned if no UUID information is known.
Status: current Access: read-only
OBJECT-TYPE    
  UUIDorZero  

docsRphyRpdIfPhysEntityCoreIfIndex 1.3.6.1.4.1.4491.2.1.30.1.2.1.1.20
If the entity represents an ifTable interface on the CCAP Core, this attribute provides the ifIndex assigned by the CCAP Core to that entity. Otherwise, this attribute returns a value of zero.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

docsRphyRpdIfPhysEntSensorTable 1.3.6.1.4.1.4491.2.1.30.1.2.2
This table contains one row per physical sensor represented by an associated row in the docsRphyRpdIfPhysEntityTable. See the reference for additional requirements.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdIfPhysEntSensorEntry

docsRphyRpdIfPhysEntSensorEntry 1.3.6.1.4.1.4491.2.1.30.1.2.2.1
Information about a particular physical sensor. An entry in this table describes the present reading of a sensor, the measurement units and scale, and sensor operational status. Entries are created in this table by the agent. The CCAP Core SHOULD create an entry for each physical sensor at the same time as the associated Entity table instance. The CCAP Core SHOULD delete an entry if the associated Entity table entry is deleted.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdIfPhysEntSensorEntry  

docsRphyRpdIfPhysEntSensorType 1.3.6.1.4.1.4491.2.1.30.1.2.2.1.1
This attribute reports the type of data returned by the associated Value attribute. The CCAP Core SHOULD set the value during instance creation. The CCAP Core SHOULD NOT change the value during operation.
Status: current Access: read-only
OBJECT-TYPE    
  EntitySensorDataType  

docsRphyRpdIfPhysEntSensorScale 1.3.6.1.4.1.4491.2.1.30.1.2.2.1.2
This attribute reports a data scaling factor, represented with an International System of Units (SI) prefix. The actual data units are determined by examining this attribute together with the associated SensorType attribute. This attribute is defined together with SensorType and Precision. Together, these three attributes are used to identify the semantics of the Value attribute.
Status: current Access: read-only
OBJECT-TYPE    
  EntitySensorDataScale  

docsRphyRpdIfPhysEntSensorPrecision 1.3.6.1.4.1.4491.2.1.30.1.2.2.1.3
This attribute reports the number of decimal places of precision in fixed-point sensor values returned by the associated Value attribute. This attribute should be set to '0' when the associated SensorType value is not a fixed-point type: e.g., 'percentRH(9)', 'rpm(10)', 'cmm(11)', or 'truthvalue(12)'.
Status: current Access: read-only
OBJECT-TYPE    
  EntitySensorPrecision  

docsRphyRpdIfPhysEntSensorValue 1.3.6.1.4.1.4491.2.1.30.1.2.2.1.4
This attribute reports the most recent measurement obtained by the RPD for this sensor. To correctly interpret the value of this object, the associated SensorType, SensorScale, and SensorPrecision attributes must also be examined.
Status: current Access: read-only
OBJECT-TYPE    
  EntitySensorValue  

docsRphyRpdIfPhysEntSensorOperStatus 1.3.6.1.4.1.4491.2.1.30.1.2.2.1.5
The operational status of the sensor.
Status: current Access: read-only
OBJECT-TYPE    
  EntitySensorStatus  

docsRphyRpdIfPhysEntSensorUnitsDisplay 1.3.6.1.4.1.4491.2.1.30.1.2.2.1.6
A textual description of the data units that should be used in the display of SensorValue.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdIfPhysEntSensorValueTimeStamp 1.3.6.1.4.1.4491.2.1.30.1.2.2.1.7
This attribute reports the value of RpdSysUpTime at the time the status and/or value of this sensor was last obtained by the RPD.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

docsRphyRpdIfPhysEntSensorValueUpdateRate 1.3.6.1.4.1.4491.2.1.30.1.2.2.1.8
This attribute reports an indication of the frequency that the CCAP Core updates the associated Value object, represented in milliseconds. The value zero indicates: - the sensor value is updated on demand - the sensor value is updated when the sensor value changes (event-driven) - the RPD does not know the update rate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdIfEnetTable 1.3.6.1.4.1.4491.2.1.30.1.2.3
This table provides details about the Ethernet interfaces on the RPD. The attributes of this object are based on the ifTable/ifXTable specified in RFC 2863. The CCAP Core MUST create an instance of this object for every Ethernet interface on the RPD. See the reference for additional requirements.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdIfEnetEntry

docsRphyRpdIfEnetEntry 1.3.6.1.4.1.4491.2.1.30.1.2.3.1
An entry containing management information applicable to a particular interface. The Ethernet IfIndex is chosen by the RPD.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdIfEnetEntry  

docsRphyRpdIfEnetPortIndex 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.1
This key attribute reports a unique index for this Ethernet port interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..255  

docsRphyRpdIfEnetDescr 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.2
A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the interface hardware/software.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..255)  

docsRphyRpdIfEnetName 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.3
This attribute reports a textual string representing a name that describes the interface. The CCAP Core MUST populate this object with the ID that is used in GCP for this port.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyRpdIfEnetAlias 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.4
This attribute reports an Alias for the interface. On the first instantiation of an interface, the value of Alias associated with that interface is the zero-length string. As and when a value is written into an instance of Alias through a network management operation, then the RPD retains the supplied value in the Alias instance associated with the same interface for as long as that interface remains instantiated, including across all re-initializations/reboots of the network management system, including those which result in a change of the interface's EnetPortIndex value.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString Size(0..64)  

docsRphyRpdIfEnetType 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.5
This attribute reports the type of interface. Additional values for Type are assigned by the Internet Assigned Numbers Authority (IANA), through updating the syntax of the IANAifType textual convention. The types are defined in the IANAifType-MIB. The value reported by this attribute is ethernetCsmacd.
Status: current Access: read-only
OBJECT-TYPE    
  IANAifType  

docsRphyRpdIfEnetMtu 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.6
This attribute reports the size of the largest packet which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

docsRphyRpdIfEnetPhysAddress 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.7
This attribute reports the interface's address at its protocol sub-layer. For example, for an 802.x interface, this attribute normally contains a MAC address. The interface's media-specific MIB defines the bit and byte ordering and the format of the value of this attribute. For interfaces which do not have such an address (e.g., a serial line), this attribute reports an octet string of zero length.
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

docsRphyRpdIfEnetAdminStatus 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.8
This attribute reports the state of the interface. The testing(3) state indicates that no operational packets can be passed. When a managed system initializes, all interfaces start with AdminStatus in the down(2) state. As a result of either explicit management action or per configuration information retained by the managed system, AdminStatus is then changed to either the up(1) or testing(3) states (or remains in the down(2) state).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

docsRphyRpdIfEnetOperStatus 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.9
This attribute reports the current operational state of the interface. The testing(3) state indicates that no operational packets can be passed. If AdminStatus is down(2) then ifOperStatus should be down(2). If AdminStatus is changed to up(1), then OperStatus should change to up(1) if the interface is ready to transmit and receive network traffic; it should change to dormant(5) if the interface is waiting for external actions (such as a serial line waiting for an incoming connection); it should remain in the down(2) state if and only if there is a fault that prevents it from going to the up(1) state; it should remain in the notPresent(6) state if the interface has missing (typically, hardware) components.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3), unknown(4), dormant(5), notPresent(6), lowerLayerDown(7)  

docsRphyRpdIfEnetLastChange 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.10
This attribute reports the value of RpdSysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this attribute reports a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

docsRphyRpdIfEnetLinkUpDownTrapEnable 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.11
This attribute reports whether linkup/linkdown traps are generated for this interface. A value of true indicates that traps are enabled. A value of false indicates that traps are disabled.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

docsRphyRpdIfEnetHighSpeed 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.12
This attribute reports an estimate of the interface's current bandwidth in units of 1,000,000 bits per second. If this attribute reports a value of 'n' then the speed of the interface is somewhere in the range of 'n-500,000' to 'n+499,999'. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this attribute reports the nominal bandwidth.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

docsRphyRpdIfEnetPromiscuousMode 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.13
This attribute reports a value of '2' (false) if this interface only accepts packets/frames that are addressed to this interface. This attribute reports a value of '1' (true) when the station accepts all packets/frames transmitted on the media. The value of PromiscuousMode does not affect the reception of broadcast and multicast packets/frames by the interface.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

docsRphyRpdIfEnetConnectorPresent 1.3.6.1.4.1.4491.2.1.30.1.2.3.1.14
This attribute reports the value 'true' if the interface sublayer has a physical connector and the value 'false' otherwise.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

docsRphyRpdIfEnetStatsTable 1.3.6.1.4.1.4491.2.1.30.1.2.4
This table reports statistics for the Ethernet interfaces on the RPD. The attributes of this object are based on the ifTable/ifXTable specified in RFC 2863. The CCAP Core MUST create an instance of this object for every EnetIf object instance. Discontinuities in the value of these counters can occur at reinitialization of the managed system, and at other times as indicated by the value of CounterDiscontinuityTime. See the reference for additional requirements.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdIfEnetStatsEntry

docsRphyRpdIfEnetStatsEntry 1.3.6.1.4.1.4491.2.1.30.1.2.4.1
An entry containing statistical information applicable to a particular RPD ethernet interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdIfEnetStatsEntry  

docsRphyRpdIfEnetStatsInOctets 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.1
The total number of octets received on the interface, including framing characters.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsOutOctets 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.2
The total number of octets transmitted out of the interface, including framing characters.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsInFrames 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.3
The total number of frames received on the interface, including framing characters.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsOutFrames 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.4
The total number of frames transmitted out of the interface, including framing characters.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsInUnicastOctets 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.5
The number of octets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsOutUnicastOctets 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.6
The total number of octets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsInUnicastFrames 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.7
The number of frames, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsOutUnicastFrames 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.8
The total number of frames that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsInMulticastOctets 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.9
The number of octets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsOutMulticastOctets 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.10
The total number of octets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsInMulticastFrames 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.11
The number of frames, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsOutMulticastFrames 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.12
The total number of frames that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsInBroadcastOctets 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.13
The number of octets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsOutBroadcastOctets 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.14
The total number of octets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsInBroadcastFrames 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.15
The number of frames, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsOutBroadcastFrames 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.16
The total number of frames that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsInDiscards 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.17
The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsOutDiscards 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.18
The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsInErrors 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.19
For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character- oriented or fixed-length interfaces, the number of inbound transmission units that contained errors preventing them from being deliverable to a higher-layer protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsOutErrors 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.20
For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not be transmitted because of errors.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsInUnknownProtos 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.21
For packet-oriented interfaces, the number of packets received via the interface which were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protocol multiplexing the number of transmission units received via the interface which were discarded because of an unknown or unsupported protocol. For any interface that does not support protocol multiplexing, this counter will always be 0.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIfEnetStatsCounterDiscontinuityTime 1.3.6.1.4.1.4491.2.1.30.1.2.4.1.22
The value of sysUpTime on the most recent occasion at which any one or more of this interface's counters suffered a discontinuity. The relevant counters are the specific instances associated with this interface of any Counter32 or Counter64 object contained in the docsRphyRpdIfEnetStatsTable. If no such discontinuities have occurred since the last re- initialization of the local management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

docsRphyRpdIfRpdEnetToCoreEntityMapTable 1.3.6.1.4.1.4491.2.1.30.1.2.5
If the RPD implements an Entity for an Ethernet port (which is optional), this table provides the mapping between the RPD's EnetPortIndex as signaled in GCP and the corresponding docsRphyRpdIfPhysEntityIndex assigned by the CCAP Core to report that entity. See the reference for additional requirements.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdIfRpdEnetToCoreEntityMapEntry

docsRphyRpdIfRpdEnetToCoreEntityMapEntry 1.3.6.1.4.1.4491.2.1.30.1.2.5.1
An entry in docsRphyRpdIfRpdEnetToCoreEntityMapTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdIfRpdEnetToCoreEntityMapEntry  

docsRphyRpdIfRpdEnetToCoreEntityMapEntityIndex 1.3.6.1.4.1.4491.2.1.30.1.2.5.1.1
The value of this attribute must match the value of docsRphyRpdIfPhysEntityIndex for the row in docsRphyRpdIfPhysEntityTable that reports the RPD Ethernet port signaled in GCP with EnetPortIndex.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdIfCoreToRpdMapTable 1.3.6.1.4.1.4491.2.1.30.1.2.6
This table maps certain CCAP Core ifTable interfaces identified with an ifIndex to an RPD interface identified in GCP. See the reference for additional requirements.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdIfCoreToRpdMapEntry

docsRphyRpdIfCoreToRpdMapEntry 1.3.6.1.4.1.4491.2.1.30.1.2.6.1
An entry in docsRphyRpdIfCoreToRpdMapTable. An entry exists for each RPD interface directly represented in the CCAP ifTable. The IfIndex corresponds to a CCAP Core ifIndex for one of the following interface types implemented on an RPD: - docsCableDownstream(128) - docsCableUpstreamChannel(205) - docsCableUpstreamRfPort(255) - docsCableDownstreamRfPort(256) - docsCableDownstreamOfdm(277) - docsCableUpstreamOfdma(278) Note that this table does not contain an instance for ifType ethernetCsmacd(6) because the Ethernet ports of the RPD are considered internal to a logical CCAP and are not reported in the CCAP ifTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdIfCoreToRpdMapEntry  

docsRphyRpdIfCoreToRpdMapRpdUniqueId 1.3.6.1.4.1.4491.2.1.30.1.2.6.1.1
This attribute specifies the MAC address associated with the lowest numbered CIN facing Ethernet port. The value of this attribute matches the value of the docsRphyRpdDevInfoUniqueId attribute from the docsRphyRpdDevInfoTable.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

docsRphyRpdIfCoreToRpdMapRpdRfPortDirection 1.3.6.1.4.1.4491.2.1.30.1.2.6.1.2
This attribute reports the direction of an RF port, which together with RpdRfPortIndex uniquely identifies an RF port on the RPD. The RF port direction is signalled in the GCP 'RfPortType' TLV 13.2 for an RF port interface or implied by the value of the GCP 'RfChannelType' TLV 12.2 for an RF channel interface.
Status: current Access: read-only
OBJECT-TYPE    
  IfDirection  

docsRphyRpdIfCoreToRpdMapRpdRfPortIndex 1.3.6.1.4.1.4491.2.1.30.1.2.6.1.3
This attribute reports the Index of an RF port on an RPD, which together with RpdRfPortDirection uniquely identifies an RF port on the RPD. The value matches the value signaled in GCP 'RfPortIndex' TLV 12.1 or the GCP 'RfPortIndex1' TLV 13.1.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

docsRphyRpdIfCoreToRpdMapRpdRfChanType 1.3.6.1.4.1.4491.2.1.30.1.2.6.1.4
For RF channel interfaces, This attribute reports the type of the channel as signaled in the GCP 'RfChannelType' TLV 12.2. For RF port interfaces, this attribute must be set to other(0). Each value of this attribute corresponds to a separate sequence of channel indices.
Status: current Access: read-only
OBJECT-TYPE    
  RphyChannelType  

docsRphyRpdIfCoreToRpdMapRpdRfChanIndex 1.3.6.1.4.1.4491.2.1.30.1.2.6.1.5
For interfaces corresponding to RF channels, this attribute reports the channel of the type specified in RpdRfChannelType, and matches the value signaled in the GCP 'RfChannelIndex' TLV 12.3. For RF port interfaces, this attribute reports 0.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

docsRphyRpdIfRpdToCoreMapTable 1.3.6.1.4.1.4491.2.1.30.1.2.7
This table maps certain RPD interface identified via GCP integers to an ifIndex reported by the CCAP Core. This table instruments the same information as the docsRphyRpdIfCoreToRpdMapTable, but with different indexing than that table. See the reference for additional requirements.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdIfRpdToCoreMapEntry

docsRphyRpdIfRpdToCoreMapEntry 1.3.6.1.4.1.4491.2.1.30.1.2.7.1
An entry in docsRphyRpdIfRpdToCoreMapTable. An entry exists for each RPD interface directly represented in the CCAP ifTable. The index 'CoreIfIndex' corresponds to a CCAP core ifIndex for one of the following interface types implemented on an RPD: - docsCableDownstream(128) - docsCableUpstreamChannel(205) - docsCableUpstreamRfPort(255) - docsCableDownstreamRfPort(256) - docsCableDownstreamOfdm(277) - docsCableUpstreamOfdma(278) Note that this table does not contain an instance for ifType ethernetCsmacd(6) because the Ethernet ports of the RPD are considered internal to a logical CCAP and are not reported in the CCAP ifTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdIfRpdToCoreMapEntry  

docsRphyRpdIfRpdToCoreMapRpdRfPortDirection 1.3.6.1.4.1.4491.2.1.30.1.2.7.1.1
This attribute reports the direction of an RF port, which together with RpdRfPortIndex uniquely identifies an RF port on the RPD. The RF port direction is signalled in the GCP 'RfPortType' TLV 13.2 for an RF port interface or implied by the value of the GCP 'RfChannelType' TLV 12.2 for an RF channel interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  IfDirection  

docsRphyRpdIfRpdToCoreMapRpdRfPortIndex 1.3.6.1.4.1.4491.2.1.30.1.2.7.1.2
This attribute reports the Index of an RF port on an RPD, which together with RpdRfPortDirection uniquely identifies an RF port on the RPD. The value matches the value signaled in GCP 'RfPortIndex' TLV 12.1 or the GCP 'RfPortIndex1' TLV 13.1.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..255  

docsRphyRpdIfRpdToCoreMapRpdRfChanType 1.3.6.1.4.1.4491.2.1.30.1.2.7.1.3
For RF channel interfaces, This attribute reports the type of the channel as signaled in the GCP 'RfChannelType' TLV 12.2. For RF port interfaces, this attribute must be set to other(0). Each value of this attribute corresponds to a separate sequence of channel indices.
Status: current Access: not-accessible
OBJECT-TYPE    
  RphyChannelType  

docsRphyRpdIfRpdToCoreMapRpdRfChanIndex 1.3.6.1.4.1.4491.2.1.30.1.2.7.1.4
For interfaces corresponding to RF channels, this attribute reports the channel of the type specified in RpdRfChannelType, and matches the value signaled in the GCP 'RfChannelIndex' TLV 12.3. For RF port interfaces, this attribute reports 0.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..255  

docsRphyRpdIfRpdToCoreMapCoreIfIndex 1.3.6.1.4.1.4491.2.1.30.1.2.7.1.5
This key attribute reports the CCAP Core IfIndex for the RPD Interface identified in GCP.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

docsRphyRpdIpv4GrpTable 1.3.6.1.4.1.4491.2.1.30.1.3.1
The table containing per-RPD IPv4-specific information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdIpv4GrpEntry

docsRphyRpdIpv4GrpEntry 1.3.6.1.4.1.4491.2.1.30.1.3.1.1
An entry containing IPv4-specific information for a specific RPD.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdIpv4GrpEntry  

docsRphyRpdIpv4GrpDefaultTTL 1.3.6.1.4.1.4491.2.1.30.1.3.1.1.1
The default value inserted into the Time-To-Live field of the IPv4 header of datagrams originated at this entity, whenever a TTL value is not supplied by the transport layer protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..255  

docsRphyRpdIpv4GrpInterfaceTableLastChange 1.3.6.1.4.1.4491.2.1.30.1.3.1.1.2
This attribute reports the value of RpdSysUpTime on the most recent occasion at which an instance of the Ipv4Interface object was added or deleted, or when a ReasmMaxSize or an EnableStatus attribute of the Ipv4Interface object was modified.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

docsRphyRpdIpv6GrpTable 1.3.6.1.4.1.4491.2.1.30.1.3.2
The table containing per-RPD IPv6-specific information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdIpv6GrpEntry

docsRphyRpdIpv6GrpEntry 1.3.6.1.4.1.4491.2.1.30.1.3.2.1
An entry containing IPv6-specific information for a specific RPD.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdIpv6GrpEntry  

docsRphyRpdIpv6GrpIpDefaultHopLimit 1.3.6.1.4.1.4491.2.1.30.1.3.2.1.1
The default value inserted into the Hop Limit field of the IPv6 header of datagrams originated at this entity whenever a Hop Limit value is not supplied by the transport layer protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

docsRphyRpdIpv6GrpInterfaceTableLastChange 1.3.6.1.4.1.4491.2.1.30.1.3.2.1.2
This attribute reports the value of RpdSysUpTime on the most recent occasion at which an instance of the Ipv6Interface object was added or deleted or when a ReasmMaxSize, InterfaceIdentifier, EnableStatus, ReachableTime, RetransmitTime, or Forwarding attribute of the Ipv6Interface object was modified.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

docsRphyRpdIpv6GrpIfStatsTableLastChange 1.3.6.1.4.1.4491.2.1.30.1.3.2.1.3
This attribute reports the value of RpdSysUpTime on the most recent occasion at which an instance of the ipIfStats object was added or deleted.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

docsRphyRpdIpv4InterfaceTable 1.3.6.1.4.1.4491.2.1.30.1.3.3
The table containing per-interface IPv4-specific information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdIpv4InterfaceEntry

docsRphyRpdIpv4InterfaceEntry 1.3.6.1.4.1.4491.2.1.30.1.3.3.1
An entry containing IPv4-specific information for an RPD's ethernet port.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdIpv4InterfaceEntry  

docsRphyRpdIpv4InterfaceEnableStatus 1.3.6.1.4.1.4491.2.1.30.1.3.3.1.1
The indication of whether IPv4 is enabled (up) or disabled (down) on this interface. This object does not affect the state of the interface itself, only its connection to an IPv4 stack. The IF-MIB should be used to control the state of the interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

docsRphyRpdIpv4InterfaceRetransmitTime 1.3.6.1.4.1.4491.2.1.30.1.3.3.1.2
The time between retransmissions of ARP requests to a neighbor when resolving the address or when probing the reachability of a neighbor.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdIpv6InterfaceTable 1.3.6.1.4.1.4491.2.1.30.1.3.4
The table containing per-interface IPv6-specific information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdIpv6InterfaceEntry

docsRphyRpdIpv6InterfaceEntry 1.3.6.1.4.1.4491.2.1.30.1.3.4.1
An entry containing IPv6-specific information for an RPD's ethernet port.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdIpv6InterfaceEntry  

docsRphyRpdIpv6InterfaceIdentifier 1.3.6.1.4.1.4491.2.1.30.1.3.4.1.1
The Interface Identifier for this interface. The Interface Identifier is combined with an address prefix to form an interface address. By default, the Interface Identifier is auto-configured according to the rules of the link type to which this interface is attached. A zero length identifier may be used where appropriate.
Status: current Access: read-only
OBJECT-TYPE    
  Ipv6AddressIfIdentifierTC  

docsRphyRpdIpv6InterfaceEnableStatus 1.3.6.1.4.1.4491.2.1.30.1.3.4.1.2
The indication of whether IPv6 is enabled (up) or disabled (down) on this interface. This object does not affect the state of the interface itself, only its connection to an IPv6 stack. The IF-MIB should be used to control the state of the interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

docsRphyRpdIpv6InterfaceReachableTime 1.3.6.1.4.1.4491.2.1.30.1.3.4.1.3
The time a neighbor is considered reachable after receiving a reachability confirmation.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdIpv6InterfaceRetransmitTime 1.3.6.1.4.1.4491.2.1.30.1.3.4.1.4
The time between retransmissions of Neighbor Solicitation messages to a neighbor when resolving the address or when probing the reachability of a neighbor.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdIpIfStatsTable 1.3.6.1.4.1.4491.2.1.30.1.3.5
This table provides statistics for IP Packets sent or received by an RPD's own IP Address. It is modeled after the IP-MIB IpIfStatsTable described in RFC 4293; however, all counters are 64 bit. Discontinuities in the value of these counters can occur at re-initialization of the management system, and at other times as indicated by the value of the DiscontinuityTime attribute in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdIpIfStatsEntry

docsRphyRpdIpIfStatsEntry 1.3.6.1.4.1.4491.2.1.30.1.3.5.1
An interface statistics entry containing objects for a particular interface and version of IP.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdIpIfStatsEntry  

docsRphyRpdIpIfStatsIPVersion 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.1
This key attribute reports the IP version of this entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetVersion  

docsRphyRpdIpIfStatsInReceives 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.2
The total number of input IP datagrams received, including those received in error.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIpIfStatsInOctets 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.3
The total number of octets received in input IP datagrams, including those received in error.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIpIfStatsInHdrErrors 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.4
The number of input IP datagrams discarded due to errors in their IP headers, including version number mismatch, other format errors, hop count exceeded, errors discovered in processing their IP options, etc.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIpIfStatsInNoRoutes 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.5
The number of input IP datagrams discarded because no route could be found to transmit them to their destination.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIpIfStatsInAddrErrors 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.6
The number of input IP datagrams discarded because the IP address in their IP header's destination field was not a valid address to be received at this entity. This count includes invalid addresses (e.g., ::0). For entities that are not IP routers and therefore do not forward datagrams, this counter includes datagrams discarded because the destination address was not a local address.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIpIfStatsInUnknownProtos 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.7
The number of locally-addressed IP datagrams received successfully but discarded because of an unknown or unsupported protocol. When tracking interface statistics, the counter of the interface to which these datagrams were addressed is incremented. This interface might not be the same as the input interface for some of the datagrams.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIpIfStatsInTruncatedPkts 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.8
The number of input IP datagrams discarded because the datagram frame didn't carry enough data.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIpIfStatsInDiscards 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.9
The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but were discarded (e.g., for lack of buffer space). Note that this counter does not include any datagrams discarded while awaiting re-assembly.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIpIfStatsInDelivers 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.10
The total number of datagrams successfully delivered to IP user-protocols (including ICMP).
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIpIfStatsOutRequests 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.11
The total number of IP datagrams that local IP user- protocols (including ICMP) supplied to IP in requests for transmission.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIpIfStatsOutDiscards 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.12
The number of output IP datagrams for which no problem was encountered to prevent their transmission to their destination, but were discarded (e.g., for lack of buffer space). Note that this counter would include datagrams counted in docsRphyRpdIpIfStatsOutForwDatagrams if any such datagrams met this (discretionary) discard criterion.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIpIfStatsOutTransmits 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.13
The total number of IP datagrams that this entity supplied to the lower layers for transmission.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIpIfStatsOutOctets 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.14
The total number of octets in IP datagrams delivered to the lower layers for transmission.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIpIfStatsInMcastPkts 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.15
The number of IP multicast datagrams received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIpIfStatsInMcastOctets 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.16
The total number of octets received in IP multicast datagrams.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIpIfStatsOutMcastPkts 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.17
The number of IP multicast datagrams transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIpIfStatsOutMcastOctets 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.18
The total number of octets transmitted in IP multicast datagrams.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIpIfStatsDiscontinuityTime 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.19
The value of sysUpTime on the most recent occasion at which any one or more of this entry's counters suffered a discontinuity.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

docsRphyRpdIpIfStatsRefreshRate 1.3.6.1.4.1.4491.2.1.30.1.3.5.1.20
The minimum reasonable polling interval for this entry. This object provides an indication of the minimum amount of time required to update the counters in this entry.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyRpdIpAddressTable 1.3.6.1.4.1.4491.2.1.30.1.3.6
This table contains addressing information relevant to the entity's interfaces. This table does not contain multicast address information. Note well: When including IPv6 link-local addresses in this table, the entry must use an InetAddressType of 'docsRphyRpdIpv6z' in order to differentiate between the possible interfaces.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdIpAddressEntry

docsRphyRpdIpAddressEntry 1.3.6.1.4.1.4491.2.1.30.1.3.6.1
An address mapping for a particular interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdIpAddressEntry  

docsRphyRpdIpAddressAddrType 1.3.6.1.4.1.4491.2.1.30.1.3.6.1.1
The address type of docsRphyRpdIpAddressAddr.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

docsRphyRpdIpAddressAddr 1.3.6.1.4.1.4491.2.1.30.1.3.6.1.2
The IP address to which this entry's addressing information pertains. The address type of this object is specified in AddrType. Implementors need to be aware that if the size of Addr exceeds 116 octets, then OIDS of instances of columns in this row will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

docsRphyRpdIpAddressEnetPortIndex 1.3.6.1.4.1.4491.2.1.30.1.3.6.1.3
This attribute reports a unique index for this Ethernet port interface.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..255  

docsRphyRpdIpAddressType 1.3.6.1.4.1.4491.2.1.30.1.3.6.1.4
The type of address. broadcast(3) is not a valid value for IPv6 addresses (RFC 3513).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unicast(1), anycast(2), broadcast(3)  

docsRphyRpdIpAddressPrefixLen 1.3.6.1.4.1.4491.2.1.30.1.3.6.1.5
This attribute reports the prefix length associated with this address.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressPrefixLength  

docsRphyRpdIpAddressOrigin 1.3.6.1.4.1.4491.2.1.30.1.3.6.1.6
The origin of the address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddressOriginTC  

docsRphyRpdIpAddressStatus 1.3.6.1.4.1.4491.2.1.30.1.3.6.1.7
The status of the address, describing if the address can be used for communication. In the absence of other information, an IPv4 address is always preferred(1).
Status: current Access: read-only
OBJECT-TYPE    
  IpAddressStatusTC  

docsRphyRpdIpAddressCreated 1.3.6.1.4.1.4491.2.1.30.1.3.6.1.8
The value of sysUpTime at the time this entry was created. If this entry was created prior to the last re- initialization of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

docsRphyRpdIpAddressLastChanged 1.3.6.1.4.1.4491.2.1.30.1.3.6.1.9
The value of sysUpTime at the time this entry was last updated. If this entry was updated prior to the last re- initialization of the local network management subsystem, then this object contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

docsRphyRpdIpNetToPhysicalTable 1.3.6.1.4.1.4491.2.1.30.1.3.7
The IP Address Translation table used for mapping from IP addresses to physical addresses. The Address Translation tables contain the IP address to 'physical' address equivalences. Some interfaces do not use translation tables for determining address equivalences (e.g., DDN-X.25 has an algorithmic method); if all interfaces are of this type, then the Address Translation table is empty, i.e., has zero entries. While many protocols may be used to populate this table, ARP and Neighbor Discovery are the most likely options.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdIpNetToPhysicalEntry

docsRphyRpdIpNetToPhysicalEntry 1.3.6.1.4.1.4491.2.1.30.1.3.7.1
Each entry contains one IP address to `physical' address equivalence.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdIpNetToPhysicalEntry  

docsRphyRpdIpNetToPhysicalNetAddressType 1.3.6.1.4.1.4491.2.1.30.1.3.7.1.1
The type of NetAddress.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

docsRphyRpdIpNetToPhysicalNetAddress 1.3.6.1.4.1.4491.2.1.30.1.3.7.1.2
The IP Address corresponding to the media-dependent 'physical' address. The address type of this object is specified in AddressType. Implementors need to be aware that if the size of NetAddress exceeds 115 octets, then OIDS of instances of columns in this row will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

docsRphyRpdIpNetToPhysicalPhysAddress 1.3.6.1.4.1.4491.2.1.30.1.3.7.1.3
The media-dependent 'physical' address.
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress Size(0..65535)  

docsRphyRpdIpNetToPhysicalLastUpdated 1.3.6.1.4.1.4491.2.1.30.1.3.7.1.4
This attribute reports the value of RpdSysUpTime at the time this entry was last updated. If this entry was updated prior to the last re-initialization of the local network management subsystem, then this attribute contains a zero value.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

docsRphyRpdIpNetToPhysicalType 1.3.6.1.4.1.4491.2.1.30.1.3.7.1.5
The type of mapping. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant Type attribute. The 'dynamic(3)' type indicates that the IP address to physical addresses mapping has been dynamically resolved using e.g., IPv4 ARP or the IPv6 Neighbor Discovery protocol. The 'static(4)' type indicates that the mapping has been statically configured. Both of these refer to entries that provide mappings for other entities addresses. The 'local(5)' type indicates that the mapping is provided for an entity's own interface address.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), invalid(2), dynamic(3), static(4), local(5)  

docsRphyRpdIpNetToPhysicalState 1.3.6.1.4.1.4491.2.1.30.1.3.7.1.6
The Neighbor Unreachability Detection state for the interface when the address mapping in this entry is used. If Neighbor Unreachability Detection is not in use (e.g. for IPv4), this object is always unknown(6).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER reachable(1), stale(2), delay(3), probe(4), invalid(5), unknown(6), incomplete(7)  

docsRphyRpdIpDefaultRouterTable 1.3.6.1.4.1.4491.2.1.30.1.3.8
The table used to describe the default routers known to the RPD.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdIpDefaultRouterEntry

docsRphyRpdIpDefaultRouterEntry 1.3.6.1.4.1.4491.2.1.30.1.3.8.1
Each entry contains information about a default router known to the RPD.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdIpDefaultRouterEntry  

docsRphyRpdIpDefaultRouterAddressType 1.3.6.1.4.1.4491.2.1.30.1.3.8.1.1
This key attribute reports the type of IP address in the Address attribute.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

docsRphyRpdIpDefaultRouterAddress 1.3.6.1.4.1.4491.2.1.30.1.3.8.1.2
The IP address of the default router represented by this row. The address type of this object is specified in AddressType. Implementers need to be aware that if the size of Address exceeds 115 octets, then OIDS of instances of columns in this row will have more than 128 sub-identifiers and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

docsRphyRpdIpDefaultRouterLifetime 1.3.6.1.4.1.4491.2.1.30.1.3.8.1.3
The remaining length of time, in seconds, that this router will continue to be useful as a default router. A value of zero indicates that it is no longer useful as a default router. It is left to the implementer of the MIB as to whether a router with a lifetime of zero is removed from the list. For IPv6, this value should be extracted from the router advertisement messages.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

docsRphyRpdIpDefaultRouterPreference 1.3.6.1.4.1.4491.2.1.30.1.3.8.1.4
An indication of preference given to this router as a default router as described in the Default Router Preferences document. Treating the value as a 2 bit signed integer allows for simple arithmetic comparisons. For IPv4 routers or IPv6 routers that are not using the updated router advertisement format, this object is set to medium (0).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER reserved(-2), low(-1), medium(0), high(1)  

docsRphyRpdIpIcmpMsgStatsTable 1.3.6.1.4.1.4491.2.1.30.1.3.9.1
The table of system-wide per-version, per-message type ICMP counters.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyRpdIpIcmpMsgStatsEntry

docsRphyRpdIpIcmpMsgStatsEntry 1.3.6.1.4.1.4491.2.1.30.1.3.9.1.1
A conceptual row in the docsRphyRpdIpIcmpMsgStatsTable. The system should track each ICMP type value, even if that ICMP type is not supported by the system. However, a given row need not be instantiated unless a message of that type has been processed, i.e., the row for Type=X MAY be instantiated before but is required to be instantiated after the first message with Type=X is received or transmitted. After receiving or transmitting any succeeding messages with Type=X, the relevant counter must be incremented.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyRpdIpIcmpMsgStatsEntry  

docsRphyRpdIpIcmpMsgStatsIPVersion 1.3.6.1.4.1.4491.2.1.30.1.3.9.1.1.1
The IP version of the statistics. Statistics are provided for each IP version supported.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetVersion  

docsRphyRpdIpIcmpMsgStatsType 1.3.6.1.4.1.4491.2.1.30.1.3.9.1.1.2
The ICMP type field of the message type being counted by this row. Note that ICMP message types are scoped by the address type in use.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..255  

docsRphyRpdIpIcmpMsgStatsInPkts 1.3.6.1.4.1.4491.2.1.30.1.3.9.1.1.3
The number of input packets for this AF and type.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyRpdIpIcmpMsgStatsOutPkts 1.3.6.1.4.1.4491.2.1.30.1.3.9.1.1.4
The number of output packets for this AF and type.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

docsRphyCcapL2tpSessionInfoTable 1.3.6.1.4.1.4491.2.1.30.1.4.1
This table provides details for every session that terminates at the CCAP Core from the CCAP Core's point of view. There will be multiple sessions for each RPD with which the CCAP Core is associated.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyCcapL2tpSessionInfoEntry

docsRphyCcapL2tpSessionInfoEntry 1.3.6.1.4.1.4491.2.1.30.1.4.1.1
The conceptual row of docsRphyCcapL2tpSessionInfoTable. A row entry is created for every session the CCAP-Core terminates.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyCcapL2tpSessionInfoEntry  

docsRphyCcapL2tpSessionInfoLocalLcceIpAddrType 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.1
This attribute indicates whether the IP address provide in docsRphyCcapL2tpSessionInfoLocalLcceIpAddr is IPv4 or IPv6.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

docsRphyCcapL2tpSessionInfoLocalLcceIpAddr 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.2
This attribute provides the local LCCE IP address on the CCAP Core of the session detailed in the row entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress  

docsRphyCcapL2tpSessionInfoLocalId 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.3
This attribute provides the value of the session ID assigned to the session by the CCAP Core.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

docsRphyCcapL2tpSessionInfoRemoteLcceIpAddrType 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.4
This attribute indicates whether the IP address provide in docsRphyCcapL2tpSessionInfoRemoteLcceIpAddr is IPv4 or IPv6.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

docsRphyCcapL2tpSessionInfoRemoteLcceIpAddr 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.5
This attribute provides the remote-side LCCE IP address of the session detailed in the row entry.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

docsRphyCcapL2tpSessionInfoRemoteId 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.6
This attribute provides the value of the session ID assigned to the session by the remote peer (CCAP Core).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyCcapL2tpSessionInfoCoreId 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.7
This attribute provides the MAC address of the CCAP Core with which this session terminates. The CCAP Core sends its MAC address to the RPD periodically via the DOCSIS SYNC MAC Message in the Source Address field.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

docsRphyCcapL2tpSessionInfoConnCtrlID 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.8
This attribute indicates the control connection identifier (CCID) for this session.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyCcapL2tpSessionInfoUdpPort 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.9
This attribute provides the UDP Port reported by the CCAP Core when the DEPI session uses L2TPv3 Header Over UDP. This attribute reports a value of 0 when the session is running with the L2TPv3 Session IP Header. This port number is negotiated between the CCAP Core and the RPD according to the L2TPv3 RFC.
Status: current Access: read-only
OBJECT-TYPE    
  InetPortNumber  

docsRphyCcapL2tpSessionInfoDescr 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.10
This attribute provides an ASCII string constructed with the form: RemoteEndId=(pp:mmm:ccc), ... { repeated for multiple endpoints } where pp is the 0-based port num signaled in the RemoteEndId AVP mmm is the channel-type enum value from the RemoteEndId AVP ccc is the channel number from the RemoteEndId AVP.
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyCcapL2tpSessionInfoSessionType 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.11
This attribute specifies whether the session is an MPT session or PSP session.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER psp(1), mpt(2)  

docsRphyCcapL2tpSessionInfoSessionSubType 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.12
This attribute specifies the type of DEPI MPT or DEPI PSP session.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER mptLegacy(1), pspLegacy(2), mcm(3), pspDepiMultichannel(4), pspUepiScQam(5), pspUepiOfdma(6), pspBwReqScQam(7), pspBwReqOfdma(8), pspProbe(9), pspRngReqScQam(10), pspRngReqOfdma(11), pspMapScQam(12), pspMapOfdma(13), pspSpecman(14), pspPnm(15), psp551Fwd(16), psp551Ret(17), psp552Fwd(18), psp552Ret(19), pspNdf(20), pspNdr(21)  

docsRphyCcapL2tpSessionInfoMaxPayload 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.13
This attribute indicates the maximum MTU negotiated between the CCAP Core and the RPD during the session establishment process. The MTU is the layer 3 payload of a layer 2 frame.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyCcapL2tpSessionInfoPathPayload 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.14
This attribute indicates the maximum MTU traversing the CIN from CCAP Core to the RPD. This is calculated by the CCAP Core by procedures such as MTU discovery as described in the DEPI specification.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyCcapL2tpSessionInfoRpdIfMtu 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.15
This attribute provides the RPD's CIN interface MTU and is read as the value of the following L2TPV3 AVP transmitted by the RPD during session setup: DEPI Downstream PW UEPI Upstream PW DEPI Remote MTU AVP (ICRP) UEPI Remote MTU AVP (ICRP).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyCcapL2tpSessionInfoCoreIfMtu 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.16
This attribute provides the CCAP Core's CIN interface MTU and is read as the value of the following L2TPv3 AVP as received by the device during session setup: DEPI Downstream PW UEPI Upstream PW DEPI Local MTU AVP (ICRQ) UEPI Local MTU AVP (ICRQ).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyCcapL2tpSessionInfoIncludeDOCSISMsgs 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.17
This attribute returns true if the CCAP Core includes DOCSIS MAP messages and other MAC Management messages in the interface entry associated with this control entry. The CCAP Core determines whether the interface includes DOCSIS messages as part of the payload.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

docsRphyCcapL2tpSessionInfoErrorCode 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.18
The error code raised when the session is in an error state. 'invalidMACInterfaceValue' Indicates wrong assignment of the CCAP Core MAC interface ifIndex. 'invalidInterfaceValue' Indicates wrong assignment of the CCAP Core Downstream interface ifIndex 'noResourcesForInterfaceIfIndex' Indicates the CCAP Core has no more resources to assign a session to this entry. 'l2tpv3Error' An L2TPv3 StopCCN or CDN message was issued 'ifAdminStatusSetToDown' Indicates the ifAdminStatus was set to down and the session was torn down.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), invalidMACInterfaceValue(2), invalidInterfaceValue(3), noResourcesForInterfaceIndex(4), l2tpv3Error(5), ifAdminStatusSetToDown(6)  

docsRphyCcapL2tpSessionInfoCreationTime 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.19
The attribute contains the sysUptime when the entry was turned active.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

docsRphyCcapL2tpSessionInfoOperStatus 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.20
This attribute provides the current status of the pseudowire from the point of view of the specific reporting entity (CCAP-Core). Values are as follows: 'other' indicates a vendor-specific operational status. 'up' indicates that the pseudowire is ready to pass packets. 'down' indicates that pseudowire signaling is not yet finished, or indications available at the service level indicate that the pseudowire is not passing packets. 'testing' indicates that AdminStatus at the pseudowire level is set to test. 'dormant' indicates that the pseudowire is not in a condition to pass packets but is in a 'pending' state, waiting for some external event. 'notPresent' indicates that some component is missing to accomplish the setup of the pseudowire. It can be a configuration error, incomplete configuration, or a missing H/W component. 'lowerLayerDown' indicates one or more of the lower-layer interfaces responsible for running the underlying PSN is not in OperStatus 'up' state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), up(2), down(3), testing(4), dormant(5), notPresent(6), lowerLayerDown(7)  

docsRphyCcapL2tpSessionInfoLocalStatus 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.21
The attribute provides the status of the pseudowire in the local node. If the 'other' bit is set, it indicates that an additional vendor-specific status is reported. If none of the bits are set, it indicates no faults are reported.
Status: current Access: read-only
OBJECT-TYPE    
  BITS other(0), pwNotForwarding(1), servicePwRxFault(2), servicePwTxFault(3), psnPwRxFault(4), psnPwTxFault(5)  

docsRphyCcapL2tpSessionInfoLastChange 1.3.6.1.4.1.4491.2.1.30.1.4.1.1.22
The attribute provides the value of sysUpTime when the session entered its current OperStatus state from the point of view of the specific reporting entity (CCAP-Core).
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

docsRphyCcapL2tpSessionFlowTable 1.3.6.1.4.1.4491.2.1.30.1.4.2
This table represents a PSP Flow of L2TP session or for those sessions, which do not have PSP Flows, represents entire session. In the latter case the PSP Flow Id by convention is zero.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyCcapL2tpSessionFlowEntry

docsRphyCcapL2tpSessionFlowEntry 1.3.6.1.4.1.4491.2.1.30.1.4.2.1
The conceptual row of docsRphyCcapL2tpSessionFlowTable. This is an extension to docsRphyCcapL2tpSessionInfoTable for the CCAP Core.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyCcapL2tpSessionFlowEntry  

docsRphyCcapL2tpSessionFlowPspFlowId 1.3.6.1.4.1.4491.2.1.30.1.4.2.1.1
This attribute identifies a PSP Flow within the session. For sessions which do not have PSP Flows, this attribute is zero.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyCcapL2tpSessionStatsTable 1.3.6.1.4.1.4491.2.1.30.1.4.3
This table provides statistics for every session that terminates at the CCAP-Core from the CCAP Core's point of view. It also provides statistics about each tunnel session between the RPD and each CCAP Core with which the RPD is associated from the RPD's point of view.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyCcapL2tpSessionStatsEntry

docsRphyCcapL2tpSessionStatsEntry 1.3.6.1.4.1.4491.2.1.30.1.4.3.1
The conceptual row of docsRphyCcapL2tpSessionStatsTable. This table is an augmentation of docsRphyCcapL2tpSessionFlowTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyCcapL2tpSessionStatsEntry  

docsRphyCcapL2tpSessionStatsOutOfSeqPkts 1.3.6.1.4.1.4491.2.1.30.1.4.3.1.1
This attribute indicates the count of session packets that were received out of sequence from the point of view of the reporting entity. It is vendor dependent the re-sequence of packets. Implementations that do not re-sequence packets also increase the value of ifInDiscards for the respective entry.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

docsRphyCcapCinDsLatencyTable 1.3.6.1.4.1.4491.2.1.30.1.4.4
This table provides measurements on the latency on the CIN link for the session as measured by the CCAP-Core. These measurements are based on the DEPI latency measurement, specified in the Remote Downstream External PHY Interface Specification.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyCcapCinDsLatencyEntry

docsRphyCcapCinDsLatencyEntry 1.3.6.1.4.1.4491.2.1.30.1.4.4.1
The conceptual row of docsRphyCcapCinLatencyTable. A row entry is created for every session the CCAP Core terminates. This table is an augmentation of docsRphyCcapL2tpSessionFlowTable for the CCAP Core.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyCcapCinDsLatencyEntry  

docsRphyCcapCinDsLatencyLastVal 1.3.6.1.4.1.4491.2.1.30.1.4.4.1.1
This attribute indicates the latest latency measurement on this session.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyCcapCinDsLatencyLastValTime 1.3.6.1.4.1.4491.2.1.30.1.4.4.1.2
This attribute indicates the sysUpTime value of the last time the docsRphyCcapCinLatencyPerfLastVal attribute was updated.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

docsRphyCcapCinDsLatencyInterval 1.3.6.1.4.1.4491.2.1.30.1.4.4.1.3
This attribute provides the time interval used to measure periodically the CIN latency per DEPI session. Active measurement of CIN latency applies to active DEPI sessions only. This attribute is constrained to 420 seconds to prevent Master Clock counter overruns. A value zero indicates no CIN latency measurements are configured to be performed.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyCcapSessionCinDsLatencyStatsTable 1.3.6.1.4.1.4491.2.1.30.1.4.5
This table provides sequence of recent measurements of the CIN latency on the network as measured by the CCAP Core. When the table is full, the oldest measurement is replaced with a new one. This table is based on the docsIfMCmtsDepiSessionCinLatencyPerfTable object defined in the DOCS-IF-M-CMTS-MIB and has been extended for Remote PHY.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DocsRphyCcapSessionCinDsLatencyStatsEntry

docsRphyCcapSessionCinDsLatencyStatsEntry 1.3.6.1.4.1.4491.2.1.30.1.4.5.1
The conceptual row of docsRphyCcapSessionCinDsLatencyStatsTable. A row entry is created for every session the CCAP Core terminates. This is an extension to docsRphyCcapL2tpSessionFlowTable for the CCAP Core.
Status: current Access: not-accessible
OBJECT-TYPE    
  DocsRphyCcapSessionCinDsLatencyStatsEntry  

docsRphyCcapSessionCinDsLatencyStatsIntervalSeq 1.3.6.1.4.1.4491.2.1.30.1.4.5.1.1
This attribute indicates the interval sequence where the CIN latency measurement was taken. It is valid in an implementation that overrides the oldest sequence number entry with the most recent measurement.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

docsRphyCcapSessionCinDsLatencyStatsVal 1.3.6.1.4.1.4491.2.1.30.1.4.5.1.2
This attribute indicates the CIN latency value measured for the session referenced by this entry.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

docsRphyCcapSessionCinDsLatencyStatsValTime 1.3.6.1.4.1.4491.2.1.30.1.4.5.1.3
This attribute provides the sysUpTime value for the last time docsRphyCcapCinLatencyPerfVal was updated.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

docsRphyCcapSecServerCertSubject 1.3.6.1.4.1.4491.2.1.30.1.5.1
This attribute represents the subject name exactly as it is encoded in the X509 certificate. The organizationName portion of the certificate's subject name must be present. All other fields are optional. Any optional field present must be prepended with (carriage return, U+000D) (line feed, U+000A). Ordering of fields present must conform to the following: organizationName countryName stateOrProvinceName localityName organizationalUnitName organizationalUnitName= commonName
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyCcapSecServerCertIssuer 1.3.6.1.4.1.4491.2.1.30.1.5.2
This attribute represents the issuer name exactly as it is encoded in the X509 certificate. The commonName portion of the certificate's issuer name must be present. All other fields are optional. Any optional field present must be prepended with (carriage return, U+000D) (line feed, U+000A). Ordering of fields present must conform to the following: commonName countryName stateOrProvinceName localityName organizationalUnitName organizationalUnitName=
Status: current Access: read-only
OBJECT-TYPE    
  SnmpAdminString  

docsRphyCcapSecServerCertSerialNumber 1.3.6.1.4.1.4491.2.1.30.1.5.3
This attribute represents the certificate's serial number, represented as an octet string.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

docsRphyCcapSecServerCertSource 1.3.6.1.4.1.4491.2.1.30.1.5.4
This attribute indicates how the certificate reached the CCAP Core. Other (4) means that it originated from a source not identified above.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER snmp(1), configurationFile(2), externalDatabase(3), other(4), authentInfo(5), compiledIntoCode(6)  

docsRphyCcapSecServerCertCert 1.3.6.1.4.1.4491.2.1.30.1.5.5
This attribute represents an X509 DER-encoded CCAP Core certificate.
Status: current Access: read-only
OBJECT-TYPE    
  DocsX509ASN1DEREncodedCertificate  

docsRphyCcapSecServerCertCertThumbprint 1.3.6.1.4.1.4491.2.1.30.1.5.6
This attribute represents the SHA-1 hash of the CCAP Core certificate.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(20)  

docsRphyCompliance 1.3.6.1.4.1.4491.2.1.30.2.1.1
The compliance statement for RPD management features.
Status: current Access: read-only
MODULE-COMPLIANCE    

docsRphyRpdGroup 1.3.6.1.4.1.4491.2.1.30.2.2.1
Group of objects implemented in CCAP Cores which represent RPD managed objects derived via the GCP protocol.
Status: current Access: read-only
OBJECT-GROUP    

docsRphyCcapCoreGroup 1.3.6.1.4.1.4491.2.1.30.2.2.2
Group of objects implemented in CCAP Cores.
Status: current Access: read-only
OBJECT-GROUP    

docsRphyCcapSecGroup 1.3.6.1.4.1.4491.2.1.30.2.2.3
Group of objects implemented to support security in CCAP Core.
Status: current Access: read-only
OBJECT-GROUP    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor