DGS3426P-L3MGMT-MIB

File: DGS3426P-L3MGMT-MIB.mib (72044 bytes)

Imported modules

Imported symbols

Counter32	MODULE-IDENTITY	OBJECT-TYPE
IpAddress	NOTIFICATION-TYPE	Integer32
Unsigned32	PhysAddress	TruthValue
DisplayString	RowStatus	MacAddress
TimeStamp	dgs3426p

Defined Types

Ipv6Address
This data type is used to model IPv6 addresses. This is a binary string of 16 octets in network byte-order.
TEXTUAL-CONVENTION
	OCTET STRING	Size(16)

SwL3IpCtrlEntry
SEQUENCE
	swL3IpCtrlInterfaceName	DisplayString
	swL3IpCtrlIfIndex	INTEGER
	swL3IpCtrlIpAddr	IpAddress
	swL3IpCtrlIpSubnetMask	IpAddress
	swL3IpCtrlVlanName	DisplayString
	swL3IpCtrlProxyArp	INTEGER
	swL3IpCtrlSecondary	TruthValue
	swL3IpCtrlMode	INTEGER
	swL3IpCtrlAdminState	INTEGER
	swL3IpCtrlIpv6LinkLocalAddress	Ipv6Address
	swL3IpCtrlIpv6LinkLocalPrefixLen	INTEGER
	swL3IpCtrlState	RowStatus
	swL3IpCtrlIpv6LinkLocalAutoState	INTEGER
	swL3IpCtrlLocalProxyArp	INTEGER
	swL3IpCtrlDhcpv6ClientState	INTEGER
	swL3IpCtrlIpDirectedBroadcastState	INTEGER
	swL3IpCtrlIpDhcpOption12State	INTEGER
	swL3IpCtrlIpDhcpOption12HostName	DisplayString
	swL3IpCtrlDhcpv6ClientPDState	INTEGER
	swL3IpCtrlDhcpv6ClientPDPrefixName	DisplayString
	swL3IpCtrlDhcpv6ClientPDPrefix	Ipv6Address
	swL3IpCtrlDhcpv6ClientPDPrefixLen	INTEGER

SwL3Ipv6CtrlEntry
SEQUENCE
	swL3Ipv6CtrlInterfaceName	DisplayString
	swL3Ipv6CtrlMaxReassmblySize	INTEGER
	swL3Ipv6CtrlNsRetransTimer	Unsigned32
	swL3Ipv6CtrlRaState	INTEGER
	swL3Ipv6CtrlRaMinRtrAdvInterval	INTEGER
	swL3Ipv6CtrlRaMaxRtrAdvInterval	INTEGER
	swL3Ipv6CtrlRaLifeTime	INTEGER
	swL3Ipv6CtrlRaReachableTime	INTEGER
	swL3Ipv6CtrlRaRetransTime	Unsigned32
	swL3Ipv6CtrlRaHopLimit	INTEGER
	swL3Ipv6CtrlRaManagedFlag	INTEGER
	swL3Ipv6CtrlRaOtherConfigFlag	INTEGER

SwL3Ipv6AddressCtrlEntry
SEQUENCE
	swL3Ipv6AddressCtrlInterfaceName	DisplayString
	swL3Ipv6Address	Ipv6Address
	swL3Ipv6AddressCtrlPrefixLen	INTEGER
	swL3Ipv6AddressCtrlPreferredLifeTime	Unsigned32
	swL3Ipv6AddressCtrlValidLifeTime	Unsigned32
	swL3Ipv6AddressCtrlOnLinkFlag	INTEGER
	swL3Ipv6AddressCtrlAutonomousFlag	INTEGER
	swL3Ipv6AddressCtrlState	RowStatus
	swL3Ipv6AddressCtrlAddressType	INTEGER

SwL3Ipv6DHCPv6CPDAddrCtrlEntry
SEQUENCE
	swL3Ipv6DHCPv6CPDAddrCtrlInterfaceName	DisplayString
	swL3Ipv6DHCPv6CPDAddrCtrlPrefixName	DisplayString
	swL3Ipv6DHCPv6CPDAddrCtrlIPv6addr	Ipv6Address
	swL3Ipv6DHCPv6CPDAddrCtrlPrefixLen	INTEGER
	swL3Ipv6DHCPv6CPDAddrCtrlState	RowStatus

SwL3IpFdbInfoEntry
SEQUENCE
	swL3IpFdbInfoIpAddr	IpAddress
	swL3IpFdbInfoIpSubnetMask	IpAddress
	swL3IpFdbInfoPort	INTEGER
	swL3IpFdbInfoType	INTEGER

SwL3IpStaticRouteEntry
SEQUENCE
	swL3IpStaticRouteDest	IpAddress
	swL3IpStaticRouteMask	IpAddress
	swL3IpStaticRouteBkupState	INTEGER
	swL3IpStaticRouteNextHop	IpAddress
	swL3IpStaticRouteMetric	INTEGER
	swL3IpStaticRouteStatus	INTEGER

SwL3RelayDhcpCtrlEntry
SEQUENCE
	swL3RelayDhcpCtrlInterfaceName	DisplayString
	swL3RelayDhcpCtrlServer	IpAddress
	swL3RelayDhcpCtrlState	INTEGER

SwL3RelayDnsCtrlEntry
SEQUENCE
	swL3RelayDnsCtrlDomainName	DisplayString
	swL3RelayDnsCtrlIpAddr	IpAddress
	swL3RelayDnsCtrlState	INTEGER

SwL3DHCPRelayOption60DefEntry
SEQUENCE
	swL3DHCPRelayOption60DefRelayIp	IpAddress
	swL3DHCPRelayOption60DefRowStatus	RowStatus

SwL3DHCPRelayOption60Entry
SEQUENCE
	swL3DHCPRelayOption60String	DisplayString
	swL3DHCPRelayOption60RelayIp	IpAddress
	swL3DHCPRelayOption60MatchType	INTEGER
	swL3DHCPRelayOption60RowStatus	RowStatus

SwL3DHCPRelayOption61Entry
SEQUENCE
	swL3DHCPRelayOption61ClientType	INTEGER
	swL3DHCPRelayOption61ClientID	DisplayString
	swL3DHCPRelayOption61Mode	INTEGER
	swL3DHCPRelayOption61RelayIp	IpAddress
	swL3DHCPRelayOption61RowStatus	RowStatus

SwL3RouteRedistriEntry
SEQUENCE
	swL3RouteRedistriSrcProtocol	INTEGER
	swL3RouteRedistriDstProtocol	INTEGER
	swL3RouteRedistriMetric	INTEGER
	swL3RouteRedistriRowStatus	RowStatus

Defined Values

swL3MgmtMIB		1.3.6.1.4.1.171.11.70.7.3
The Structure of Layer 3 Network Management Information for the proprietary enterprise.
MODULE-IDENTITY

swL3DevMgmt		1.3.6.1.4.1.171.11.70.7.3.1
OBJECT IDENTIFIER

swL3IpMgmt		1.3.6.1.4.1.171.11.70.7.3.2
OBJECT IDENTIFIER

swL3RelayMgmt		1.3.6.1.4.1.171.11.70.7.3.3
OBJECT IDENTIFIER

swL3IpCtrlMgmt		1.3.6.1.4.1.171.11.70.7.3.2.1
OBJECT IDENTIFIER

swL3IpFdbMgmt		1.3.6.1.4.1.171.11.70.7.3.2.2
OBJECT IDENTIFIER

swL3RelayDnsMgmt		1.3.6.1.4.1.171.11.70.7.3.3.2
OBJECT IDENTIFIER

swL3DevCtrl		1.3.6.1.4.1.171.11.70.7.3.1.1
OBJECT IDENTIFIER

swL3DevCtrlRIPState		1.3.6.1.4.1.171.11.70.7.3.1.1.1
This object indicates Routing Information Protocol (RIP) version 2 function is enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL3IpCtrlAllIpIfState		1.3.6.1.4.1.171.11.70.7.3.2.1.7
This object indicates all interface function state of the device.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), enabled(2), disabled(3)

swL3IpCtrlTable		1.3.6.1.4.1.171.11.70.7.3.2.1.3
This table contain IP interface information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3IpCtrlEntry

swL3IpCtrlEntry		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1
A list of information about a specific IP interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3IpCtrlEntry

swL3IpCtrlInterfaceName		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.1
This object indicates the name of the IP interface.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..12)

swL3IpCtrlIfIndex		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.2
This object uniquely identifies the IP interface number in the swL3IpCtrlTable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL3IpCtrlIpAddr		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.3
The IP address of the interface. This object only can take the value of the unicast IP address.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

swL3IpCtrlIpSubnetMask		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.4
The IP net mask for this interface.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

swL3IpCtrlVlanName		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.5
This object indicates the IP control entry's VLAN name. The VLAN name in each entry must be unique in the IP Control Table.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

swL3IpCtrlProxyArp		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.6
This object indicates enable/disable of the proxy ARP function for IPv4.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3IpCtrlSecondary		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.7
When this is true(1), the IP address is the secondary IP. When false(2), the IP address is the primary IP.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

swL3IpCtrlMode		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.8
This object indicates the IP operation mode. other(1) - This entry is currently in use but the conditions under which it will remain are determined by each of the following values. bootp(3) - The IP address will be set automatically from a BOOTP server. dhcp(4) - The IP address will be set automatically from a DHCP server.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), bootp(3), dhcp(4)

swL3IpCtrlAdminState		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.9
The state of the IP interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3IpCtrlIpv6LinkLocalAddress		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.14
The IPv6 link local address for this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Ipv6Address

swL3IpCtrlIpv6LinkLocalPrefixLen		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.15
The IPv6 prefix length for this IPv6 link local address.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

swL3IpCtrlState		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.16
This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

swL3IpCtrlIpv6LinkLocalAutoState		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.17
The state of the IPv6 link local auto.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), enabled(2), disabled(3)

swL3IpCtrlLocalProxyArp		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.18
If the state is enabled, the switch will be allowed to respond to the proxy ARP proxy ARP when the source IP and destination IP are on the same interface.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3IpCtrlDhcpv6ClientState		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.20
The state of the Dhcpv6 Client.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3IpCtrlIpDirectedBroadcastState		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.21
The state of the IP Directed Broadcast.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3IpCtrlIpDhcpOption12State		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.22
Enable or disable insertion of option 12 in the DHCPDISCOVER and DHCPREQUEST message.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3IpCtrlIpDhcpOption12HostName		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.23
Specify the host name to be inserted in the DHCPDISCOVER and DHCPREQUEST message. The specified host name must start with a letter, end with a letter or digit, and have only letters, digits, and hyphen as interior characters; the maximal length is 63. By default, the host name is empty. When set an empty host name, means to clear the host name setting and use the default value to encode option 12.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..63)

swL3IpCtrlDhcpv6ClientPDState		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.24
The state of the Dhcpv6 Client PD.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3IpCtrlDhcpv6ClientPDPrefixName		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.25
This object indicates the name for the DHCPv6 Client PD. If the swL3IpCtrlDhcpv6ClientPDState is disabled, this object will be clear and can't write.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..12)

swL3IpCtrlDhcpv6ClientPDPrefix		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.26
The IPv6 prefix obtained form delegation router.
Status: current	Access: read-only
OBJECT-TYPE
	Ipv6Address

swL3IpCtrlDhcpv6ClientPDPrefixLen		1.3.6.1.4.1.171.11.70.7.3.2.1.3.1.27
The IPv6 prefix length for the prefix obtained from delegation router.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

swL3Ipv6CtrlTable		1.3.6.1.4.1.171.11.70.7.3.2.1.4
This table contains IPv6 information of an IP interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3Ipv6CtrlEntry

swL3Ipv6CtrlEntry		1.3.6.1.4.1.171.11.70.7.3.2.1.4.1
A list of IPv6 information about a specific IP interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3Ipv6CtrlEntry

swL3Ipv6CtrlInterfaceName		1.3.6.1.4.1.171.11.70.7.3.2.1.4.1.1
This object indicates the name of the IP interface.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..12)

swL3Ipv6CtrlMaxReassmblySize		1.3.6.1.4.1.171.11.70.7.3.2.1.4.1.2
Maximum Reassembly Size of the IP interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

swL3Ipv6CtrlNsRetransTimer		1.3.6.1.4.1.171.11.70.7.3.2.1.4.1.3
Neighbor solicitation's retransmit timer. The unit is set in milliseconds.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..4294967294

swL3Ipv6CtrlRaState		1.3.6.1.4.1.171.11.70.7.3.2.1.4.1.5
Neighbor solicited state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3Ipv6CtrlRaMinRtrAdvInterval		1.3.6.1.4.1.171.11.70.7.3.2.1.4.1.6
The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds. It must be no less than 3 seconds and no greater than .75 * MaxRtrAdvInterval. Default value: 0.33 * MaxRtrAdvInterval
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	3..1350

swL3Ipv6CtrlRaMaxRtrAdvInterval		1.3.6.1.4.1.171.11.70.7.3.2.1.4.1.7
The maximum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	4..1800

swL3Ipv6CtrlRaLifeTime		1.3.6.1.4.1.171.11.70.7.3.2.1.4.1.8
Indicates the lifetime of the router as the default router.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..9000

swL3Ipv6CtrlRaReachableTime		1.3.6.1.4.1.171.11.70.7.3.2.1.4.1.9
Indicates the amount of time that a node can consider a neighboring node reachable after receiving a reachability confirmation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..3600000

swL3Ipv6CtrlRaRetransTime		1.3.6.1.4.1.171.11.70.7.3.2.1.4.1.10
Indicates the amount of time between retransmissions of neighbor solicited messages. The unit is set in millisecond.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..4294967294

swL3Ipv6CtrlRaHopLimit		1.3.6.1.4.1.171.11.70.7.3.2.1.4.1.11
Indicates the default value of the hop limit field in the IPv6 header for packets sent by hosts that receive this RA message.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

swL3Ipv6CtrlRaManagedFlag		1.3.6.1.4.1.171.11.70.7.3.2.1.4.1.12
When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an address in the addition to the addresses derived from the stateless address configuration.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3Ipv6CtrlRaOtherConfigFlag		1.3.6.1.4.1.171.11.70.7.3.2.1.4.1.13
When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an on-link address configuration information.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3Ipv6AddressCtrlTable		1.3.6.1.4.1.171.11.70.7.3.2.1.5
This table contain IPv6 address information for each IP interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3Ipv6AddressCtrlEntry

swL3Ipv6AddressCtrlEntry		1.3.6.1.4.1.171.11.70.7.3.2.1.5.1
A list of information about a specific IPv6 address.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3Ipv6AddressCtrlEntry

swL3Ipv6AddressCtrlInterfaceName		1.3.6.1.4.1.171.11.70.7.3.2.1.5.1.1
This object indicates the name of the IP interface.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..12)

swL3Ipv6Address		1.3.6.1.4.1.171.11.70.7.3.2.1.5.1.2
Specify the IPv6 address.
Status: current	Access: read-only
OBJECT-TYPE
	Ipv6Address

swL3Ipv6AddressCtrlPrefixLen		1.3.6.1.4.1.171.11.70.7.3.2.1.5.1.3
Indicates the prefix length of this IPv6 address.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

swL3Ipv6AddressCtrlPreferredLifeTime		1.3.6.1.4.1.171.11.70.7.3.2.1.5.1.4
Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains in preferred state. For an infinite valid lifetime, the value can be set to 0xffffffff.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..4294967294

swL3Ipv6AddressCtrlValidLifeTime		1.3.6.1.4.1.171.11.70.7.3.2.1.5.1.5
Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains valid. For an infinite valid lifetime, the value can be set to 0xffffffff.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..4294967294

swL3Ipv6AddressCtrlOnLinkFlag		1.3.6.1.4.1.171.11.70.7.3.2.1.5.1.6
When enabled, the address implied by the specified prefix is available on the link where the RA message is received.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3Ipv6AddressCtrlAutonomousFlag		1.3.6.1.4.1.171.11.70.7.3.2.1.5.1.7
When enabled, the specified prefix will be used to create an autonomous address configuration.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3Ipv6AddressCtrlState		1.3.6.1.4.1.171.11.70.7.3.2.1.5.1.8
This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

swL3Ipv6AddressCtrlAddressType		1.3.6.1.4.1.171.11.70.7.3.2.1.5.1.9
This object indicates the type of the IPv6 address. manual(1): the IPv6 address is configured by user. dhcpv6(2): the IPv6 address is assigned by DHCPv6 server. stateless(3): the IPv6 address is assigned by router advertisement.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	manual(1), dhcpv6(2), stateless(3)

swL3Ipv6DHCPv6CPDAddrCtrlTable		1.3.6.1.4.1.171.11.70.7.3.2.1.6
This table contain the information of the IPv6 address which based on DHCPv6 client PD.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3Ipv6DHCPv6CPDAddrCtrlEntry

swL3Ipv6DHCPv6CPDAddrCtrlEntry		1.3.6.1.4.1.171.11.70.7.3.2.1.6.1
A list of information about a specific DHCPv6 Client PD IPv6 address.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3Ipv6DHCPv6CPDAddrCtrlEntry

swL3Ipv6DHCPv6CPDAddrCtrlInterfaceName		1.3.6.1.4.1.171.11.70.7.3.2.1.6.1.1
This object indicates the name of the IP interface.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..12)

swL3Ipv6DHCPv6CPDAddrCtrlPrefixName		1.3.6.1.4.1.171.11.70.7.3.2.1.6.1.2
This object indicates the name of the prefix based on which the IPv6 address will be generate.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..12)

swL3Ipv6DHCPv6CPDAddrCtrlIPv6addr		1.3.6.1.4.1.171.11.70.7.3.2.1.6.1.3
Specify the suffix of the IPv6 address.
Status: current	Access: read-only
OBJECT-TYPE
	Ipv6Address

swL3Ipv6DHCPv6CPDAddrCtrlPrefixLen		1.3.6.1.4.1.171.11.70.7.3.2.1.6.1.4
Indicates the prefix length of this IPv6 address.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

swL3Ipv6DHCPv6CPDAddrCtrlState		1.3.6.1.4.1.171.11.70.7.3.2.1.6.1.5
This variable displays the status of the entry. The status is used for creating and deleting instances of the objects in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

swL3IpFdbInfoTable		1.3.6.1.4.1.171.11.70.7.3.2.2.1
A table that contains forwarding and/or filtering information. This information is used by the switch in determining how to propagate the received IP packets.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3IpFdbInfoEntry

swL3IpFdbInfoEntry		1.3.6.1.4.1.171.11.70.7.3.2.2.1.1
Information about a specific IP address for which the bridge has some forwarding and/or filtering information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3IpFdbInfoEntry

swL3IpFdbInfoIpAddr		1.3.6.1.4.1.171.11.70.7.3.2.2.1.1.1
A IP address for which switch has forwarding and/or filtering information.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

swL3IpFdbInfoIpSubnetMask		1.3.6.1.4.1.171.11.70.7.3.2.2.1.1.2
A IP net mask for this interface.for which switch has forwarding and/or filtering information.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

swL3IpFdbInfoPort		1.3.6.1.4.1.171.11.70.7.3.2.2.1.1.3
Either the value '0', or the port number of the port on which packet having a IP address equal to the value of the corresponding instance of swL3IpFdbInfoIpAddr has been seen. A value of '0' indicates that the port number has not been learned but that switch does have some forwarding/filtering information about this address.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL3IpFdbInfoType		1.3.6.1.4.1.171.11.70.7.3.2.2.1.1.4
The status of this entry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), static(2), dynamic(3)

swL3IpArpAgingTime		1.3.6.1.4.1.171.11.70.7.3.2.4
The timeout period in minutes for aging out dynamically learned arp information.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

swL3IpStaticRouteTable		1.3.6.1.4.1.171.11.70.7.3.2.5
This entity's IP static Routing table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3IpStaticRouteEntry

swL3IpStaticRouteEntry		1.3.6.1.4.1.171.11.70.7.3.2.5.1
A particular route to a particular destination, under a particular policy. Once an entry be built,it shouldn't be modified.That is,it just support create and delete action.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3IpStaticRouteEntry

swL3IpStaticRouteDest		1.3.6.1.4.1.171.11.70.7.3.2.5.1.1
The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteMask object is not equal to x.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

swL3IpStaticRouteMask		1.3.6.1.4.1.171.11.70.7.3.2.5.1.2
Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the swL3IpStaticRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the swL3IpStaticRouteMask by reference to the IP Address Class. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteDest object is not equal to swL3IpStaticRouteDest.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

swL3IpStaticRouteBkupState		1.3.6.1.4.1.171.11.70.7.3.2.5.1.3
The routing state for this route.The value SHOULD be primary(1) or backup(2).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	primary(1), backup(2)

swL3IpStaticRouteNextHop		1.3.6.1.4.1.171.11.70.7.3.2.5.1.4
On remote routes, the address of the next sys- tem en route; Otherwise, 0.0.0.0.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

swL3IpStaticRouteMetric		1.3.6.1.4.1.171.11.70.7.3.2.5.1.5
The routing metric for this route.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..65535

swL3IpStaticRouteStatus		1.3.6.1.4.1.171.11.70.7.3.2.5.1.6
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry resides in the table. active(4) - the nextHop of this entry exists in the ARP table. inActive(5) - the next hop of this entry does not exist in the ARP table.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	other(1), invalid(2), valid(3), active(4), inActive(5)

swL3RelayDhcpMgmt		1.3.6.1.4.1.171.11.70.7.3.3.1
OBJECT IDENTIFIER

swL3RelayDhcpState		1.3.6.1.4.1.171.11.70.7.3.3.1.1
This object indicates Dhcp Relay function is enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL3RelayDhcpHopCount		1.3.6.1.4.1.171.11.70.7.3.3.1.2
This object indicates the maximum number of router hops that the BOOTP packets can cross.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..16

swL3RelayDhcpTimeThreshold		1.3.6.1.4.1.171.11.70.7.3.3.1.3
This object indicates the minimum time in seconds within which the switch must relay the Dhcp request. If this time is exceeded, the switch will drop the Dhcp packet.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

swL3RelayDhcpCtrlTable		1.3.6.1.4.1.171.11.70.7.3.3.1.4
This table specifys the IP address as a destination to forward (relay) DHCP packets to.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3RelayDhcpCtrlEntry

swL3RelayDhcpCtrlEntry		1.3.6.1.4.1.171.11.70.7.3.3.1.4.1
A list of information specifies the IP address as a destination to forward (relay) DHCP packets to.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3RelayDhcpCtrlEntry

swL3RelayDhcpCtrlInterfaceName		1.3.6.1.4.1.171.11.70.7.3.3.1.4.1.1
The name of the IP interface.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..12)

swL3RelayDhcpCtrlServer		1.3.6.1.4.1.171.11.70.7.3.3.1.4.1.2
The DHCP server IP address.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

swL3RelayDhcpCtrlState		1.3.6.1.4.1.171.11.70.7.3.3.1.4.1.3
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), invalid(2), valid(3)

swL3RelayDhcpOption82State		1.3.6.1.4.1.171.11.70.7.3.3.1.5
This object indicates DHCP Relay Option 82 function is enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

swL3RelayDhcpOption82CheckState		1.3.6.1.4.1.171.11.70.7.3.3.1.6
This object indicates DHCP Relay Option 82 Check function is enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(0), enabled(1)

swL3RelayDhcpOption82Policy		1.3.6.1.4.1.171.11.70.7.3.3.1.7
This object indicates DHCP Relay Option 82 Policy.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	replace(0), drop(1), keep(2)

swL3RelayDnsState		1.3.6.1.4.1.171.11.70.7.3.3.2.1
This object indicates DNS Relay function is enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL3RelayDnsPrimaryServer		1.3.6.1.4.1.171.11.70.7.3.3.2.2
This object indicates the address of the primary DNS server.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

swL3RelayDnsSecondaryServer		1.3.6.1.4.1.171.11.70.7.3.3.2.3
This object indicates the address of the secondary DNS server.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

swL3RelayDnsCacheState		1.3.6.1.4.1.171.11.70.7.3.3.2.4
This object indicates DNS Relay cache is enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL3RelayDnsStaticTableState		1.3.6.1.4.1.171.11.70.7.3.3.2.5
This object indicates DNS Relay static table is enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL3RelayDnsCtrlTable		1.3.6.1.4.1.171.11.70.7.3.3.2.6
This table display the current DNS relay static table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3RelayDnsCtrlEntry

swL3RelayDnsCtrlEntry		1.3.6.1.4.1.171.11.70.7.3.3.2.6.1
A list of information display the current DNS relay static table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3RelayDnsCtrlEntry

swL3RelayDnsCtrlDomainName		1.3.6.1.4.1.171.11.70.7.3.3.2.6.1.1
The domain name of the entry.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..32)

swL3RelayDnsCtrlIpAddr		1.3.6.1.4.1.171.11.70.7.3.3.2.6.1.2
The IP address of the entry.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

swL3RelayDnsCtrlState		1.3.6.1.4.1.171.11.70.7.3.3.2.6.1.3
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), invalid(2), valid(3)

swL3DHCPRelayOption60		1.3.6.1.4.1.171.11.70.7.3.3.1.8
OBJECT IDENTIFIER

swL3DHCPRelayOption60State		1.3.6.1.4.1.171.11.70.7.3.3.1.8.1
This object indicates DHCP relay option 60 function is enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3DHCPRelayOption60DefMode		1.3.6.1.4.1.171.11.70.7.3.3.1.8.2
This object indicates default mode that has no option 60 mathcing rules. relay(1): means to relay the packet to the IP address which is specified by swL3DHCPRelayOption60DefRelayIp. drop(2): means to drop the packet.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	relay(1), drop(2)

swL3DHCPRelayOption60DefTable		1.3.6.1.4.1.171.11.70.7.3.3.1.8.3
This table indicates the default relay servers for the packet that has no option 60 mathcing rules.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3DHCPRelayOption60DefEntry

swL3DHCPRelayOption60DefEntry		1.3.6.1.4.1.171.11.70.7.3.3.1.8.3.1
A list of information indicates the default relay servers for the packet that has no option 60 mathcing rules.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3DHCPRelayOption60DefEntry

swL3DHCPRelayOption60DefRelayIp		1.3.6.1.4.1.171.11.70.7.3.3.1.8.3.1.1
This object indicates the IP address of default relay server.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

swL3DHCPRelayOption60DefRowStatus		1.3.6.1.4.1.171.11.70.7.3.3.1.8.3.1.2
This object indicates the status of this entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

swL3DHCPRelayOption60Table		1.3.6.1.4.1.171.11.70.7.3.3.1.8.4
This table indicates the relay servers for the packet at option 60 rules.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3DHCPRelayOption60Entry

swL3DHCPRelayOption60Entry		1.3.6.1.4.1.171.11.70.7.3.3.1.8.4.1
A list of information indicates the relay servers for the packet at option 60 rules.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3DHCPRelayOption60Entry

swL3DHCPRelayOption60String		1.3.6.1.4.1.171.11.70.7.3.3.1.8.4.1.1
This object indicates string of this entry. Note that it is theoretically possible for a valid string to exceed the allowed length of an SNMP object identifier, and thus be impossible to represent in tables in this MIB that are indexed by string.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

swL3DHCPRelayOption60RelayIp		1.3.6.1.4.1.171.11.70.7.3.3.1.8.4.1.2
This object indicates the IP address of relay server.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

swL3DHCPRelayOption60MatchType		1.3.6.1.4.1.171.11.70.7.3.3.1.8.4.1.3
This object indicates match state of this entry. exact(1): means the option 60 string in the packet must full match with the specified string. partial(2): means the option 60 string in the packet only need partial match with the specified string.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	exact(1), partial(2)

swL3DHCPRelayOption60RowStatus		1.3.6.1.4.1.171.11.70.7.3.3.1.8.4.1.4
This object indicates the status of this entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

swL3DHCPRelayOption61		1.3.6.1.4.1.171.11.70.7.3.3.1.9
OBJECT IDENTIFIER

swL3DHCPRelayOption61State		1.3.6.1.4.1.171.11.70.7.3.3.1.9.1
This object indicates DHCP relay option 61 function is enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3DHCPRelayOption61DefMode		1.3.6.1.4.1.171.11.70.7.3.3.1.9.2
This object indicates default mode that has no option 61 mathcing rules. relay(1): means to relay the packet to the IP address which is specified by swL3DHCPRelayOption61DefRelayIp. drop(2): means to drop the packet.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	relay(1), drop(2)

swL3DHCPRelayOption61DefRelayIp		1.3.6.1.4.1.171.11.70.7.3.3.1.9.3
This object indicates the IP address of default relay server that has no option 61 mathcing rules. Pay attention to when swL3DHCPRelayOption61Mode is: relay(1): this object must be set together. drop(2): this object can not be set, and it always returns '0.0.0.0'.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

swL3DHCPRelayOption61Table		1.3.6.1.4.1.171.11.70.7.3.3.1.9.4
This table indicates the relay servers for the packet at option 61 rules.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3DHCPRelayOption61Entry

swL3DHCPRelayOption61Entry		1.3.6.1.4.1.171.11.70.7.3.3.1.9.4.1
A list of information indicates the relay servers for the packet at option 61 rules.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3DHCPRelayOption61Entry

swL3DHCPRelayOption61ClientType		1.3.6.1.4.1.171.11.70.7.3.3.1.9.4.1.1
This object indicates client type of this entry. mac(1): means the client-ID which is the MAC address of client. string(2): means the client-ID which is specified string by administrator.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	mac(1), string(2)

swL3DHCPRelayOption61ClientID		1.3.6.1.4.1.171.11.70.7.3.3.1.9.4.1.2
This object indicates string of this entry. When swL3DHCPRelayOption61ClientType is mac(1), the format of this object should be XX-XX-XX-XX-XX-XX (MAC address). Note that it is theoretically possible for a valid string to exceed the allowed length of an SNMP object identifier, and thus be impossible to represent in tables in this MIB that are indexed by string.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

swL3DHCPRelayOption61Mode		1.3.6.1.4.1.171.11.70.7.3.3.1.9.4.1.3
This object indicates mode of this entry. relay(1): means to relay the packet to the IP address which is specified by swL3DHCPRelayOption61RelayIp. drop(2): means to drop the packet.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	relay(1), drop(2)

swL3DHCPRelayOption61RelayIp		1.3.6.1.4.1.171.11.70.7.3.3.1.9.4.1.4
This object indicates the IP address of relay server. Pay attention to when swL3DHCPRelayOption61Mode is: relay(1): this object must be set together. drop(2): this object can not be set, and it always returns '0.0.0.0'.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

swL3DHCPRelayOption61RowStatus		1.3.6.1.4.1.171.11.70.7.3.3.1.9.4.1.5
This object indicates the status of this entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

swL3RouteRedistriTable		1.3.6.1.4.1.171.11.70.7.3.5
Route redistribution allows routers on the network that are running different routing protocols to exchange routing information. This is accomplished by comparing the routes stored in the varios routers' routing tables and assigning appropriate metrics. This information is then exchanged among the various routers according to the individual routers current routing protocol.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3RouteRedistriEntry

swL3RouteRedistriEntry		1.3.6.1.4.1.171.11.70.7.3.5.1
A list of information displaying the route redistribution table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3RouteRedistriEntry

swL3RouteRedistriSrcProtocol		1.3.6.1.4.1.171.11.70.7.3.5.1.1
Allows the selection of the protocol of the source device.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), static(4), local(5)

swL3RouteRedistriDstProtocol		1.3.6.1.4.1.171.11.70.7.3.5.1.2
Allows the selection of the protocol of the destination device.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), rip(2)

swL3RouteRedistriMetric		1.3.6.1.4.1.171.11.70.7.3.5.1.4
Allows the entry of an OSPF interface cost. This is analogous to a Hop Count in the RIP routing protocol. The value '0' indicates default value.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..16

swL3RouteRedistriRowStatus		1.3.6.1.4.1.171.11.70.7.3.5.1.5
This object indicates the status of this entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

swL3RoutePreference		1.3.6.1.4.1.171.11.70.7.3.9
OBJECT IDENTIFIER

swL3RoutePreferenceRIP		1.3.6.1.4.1.171.11.70.7.3.9.1
Used to configure the route preference of RIP.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..999

swL3RoutePreferenceStatic		1.3.6.1.4.1.171.11.70.7.3.9.3
Used to configure the route preference of Static.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..999

swL3RoutePreferenceLocal		1.3.6.1.4.1.171.11.70.7.3.9.4
Used to read the route preference of Local.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..999

swL3RoutePreferenceDefault		1.3.6.1.4.1.171.11.70.7.3.9.8
Used to configure the route preference of Default.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..999