DGS3000-28SC-L3MGMT-MIB

File: DGS3000-28SC-L3MGMT-MIB.mib (55305 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	IPV6-TC
SWDGS3000PRIMGMT-MIB	IF-MIB	INET-ADDRESS-MIB

Imported symbols

Counter32	MODULE-IDENTITY	OBJECT-TYPE
IpAddress	NOTIFICATION-TYPE	Integer32
Unsigned32	PhysAddress	TruthValue
DisplayString	RowStatus	MacAddress
TimeStamp	Ipv6Address	dlink-Dgs3000Proj-DGS3000-28SCax
InterfaceIndex	InetAddressType	InetAddress

Defined Types

NodeAddress
OCTET STRING	Size(6)

NetAddress
OCTET STRING	Size(4)

VrId
A number which, along with an interface index (ifIndex), serves to uniquely identify a virtual router on a given VRRP router. A set of one or more associated addresses is assigned to a VRID.
TEXTUAL-CONVENTION
	Integer32	1..255

SwL3IpCtrlEntry
SEQUENCE
	swL3IpCtrlInterfaceName	DisplayString
	swL3IpCtrlIfIndex	INTEGER
	swL3IpCtrlIpAddr	IpAddress
	swL3IpCtrlIpSubnetMask	IpAddress
	swL3IpCtrlVlanName	DisplayString
	swL3IpCtrlProxyArp	INTEGER
	swL3IpCtrlSecondary	TruthValue
	swL3IpCtrlMode	INTEGER
	swL3IpCtrlAdminState	INTEGER
	swL3IpCtrlIpv4AdminState	INTEGER
	swL3IpCtrlIpv6AdminState	INTEGER
	swL3IpCtrlIpv6LinkLocalAddress	Ipv6Address
	swL3IpCtrlIpv6LinkLocalPrefixLen	INTEGER
	swL3IpCtrlState	RowStatus
	swL3IpCtrlIpv6LinkLocalAutoState	INTEGER
	swL3IpCtrlLocalProxyArp	INTEGER
	swL3IpCtrlIpMtu	INTEGER
	swL3IpCtrlDhcpv6ClientState	INTEGER
	swL3IpCtrlIpDirectedBroadcastState	INTEGER
	swL3IpCtrlIpDhcpOption12State	INTEGER
	swL3IpCtrlIpDhcpOption12HostName	DisplayString
	swL3IpCtrlDhcpv6ClientPDState	INTEGER
	swL3IpCtrlDhcpv6ClientPDPrefixName	DisplayString
	swL3IpCtrlDhcpv6ClientPDPrefix	Ipv6Address
	swL3IpCtrlDhcpv6ClientPDPrefixLen	INTEGER
	swL3IpCtrlIpv6AutoConfigState	INTEGER
	swL3IpCtrlIpv6AutoConfigDefault	TruthValue
	swL3IpCtrlDhcpv6ClientRapidCommit	TruthValue
	swL3IpCtrlDhcpv6ClientPDRapidCommit	TruthValue

SwL3Ipv6CtrlEntry
SEQUENCE
	swL3Ipv6CtrlInterfaceName	DisplayString
	swL3Ipv6CtrlMaxReassmblySize	INTEGER
	swL3Ipv6CtrlNsRetransTimer	Unsigned32
	swL3Ipv6CtrlRaState	INTEGER
	swL3Ipv6CtrlRaMinRtrAdvInterval	INTEGER
	swL3Ipv6CtrlRaMaxRtrAdvInterval	INTEGER
	swL3Ipv6CtrlRaLifeTime	INTEGER
	swL3Ipv6CtrlRaReachableTime	INTEGER
	swL3Ipv6CtrlRaRetransTime	Unsigned32
	swL3Ipv6CtrlRaHopLimit	INTEGER
	swL3Ipv6CtrlRaManagedFlag	INTEGER
	swL3Ipv6CtrlRaOtherConfigFlag	INTEGER
	swL3Ipv6CtrlDadRetransNum	INTEGER

SwL3Ipv6AddressCtrlEntry
SEQUENCE
	swL3Ipv6AddressCtrlInterfaceName	DisplayString
	swL3Ipv6Address	Ipv6Address
	swL3Ipv6AddressCtrlPrefixLen	INTEGER
	swL3Ipv6AddressCtrlPreferredLifeTime	Unsigned32
	swL3Ipv6AddressCtrlValidLifeTime	Unsigned32
	swL3Ipv6AddressCtrlOnLinkFlag	INTEGER
	swL3Ipv6AddressCtrlAutonomousFlag	INTEGER
	swL3Ipv6AddressCtrlState	RowStatus
	swL3Ipv6AddressCtrlAddressType	INTEGER

SwL3Ipv6DHCPv6CPDAddrCtrlEntry
SEQUENCE
	swL3Ipv6DHCPv6CPDAddrCtrlInterfaceName	DisplayString
	swL3Ipv6DHCPv6CPDAddrCtrlPrefixName	DisplayString
	swL3Ipv6DHCPv6CPDAddrCtrlIPv6addr	Ipv6Address
	swL3Ipv6DHCPv6CPDAddrCtrlPrefixLen	INTEGER
	swL3Ipv6DHCPv6CPDAddrCtrlState	RowStatus

SwL3LoopBackIpCtrlEntry
SEQUENCE
	swL3LoopBackIpCtrlInterfaceName	DisplayString
	swL3LoopBackIpCtrlIfIndex	INTEGER
	swL3LoopBackIpCtrlIpAddr	IpAddress
	swL3LoopBackIpCtrlIpSubnetMask	IpAddress
	swL3LoopBackIpCtrlAdminState	INTEGER
	swL3LoopBackIpCtrlRowStatus	RowStatus

SwL3IpFdbInfoEntry
SEQUENCE
	swL3IpFdbInfoIpAddr	IpAddress
	swL3IpFdbInfoIpSubnetMask	IpAddress
	swL3IpFdbInfoPort	INTEGER
	swL3IpFdbInfoType	INTEGER

SwL3IpStaticRouteEntry
SEQUENCE
	swL3IpStaticRouteDest	IpAddress
	swL3IpStaticRouteMask	IpAddress
	swL3IpStaticRouteBkupState	INTEGER
	swL3IpStaticRouteNextHop	IpAddress
	swL3IpStaticRouteMetric	INTEGER
	swL3IpStaticRouteStatus	INTEGER
	swL3IpStaticRouteWeight	INTEGER
	swL3IpStaticRouteInterfaceName	DisplayString
	swL3IpStaticRouteCost	INTEGER

SwL3RelayDnsCtrlEntry
SEQUENCE
	swL3RelayDnsCtrlDomainName	DisplayString
	swL3RelayDnsCtrlIpAddr	IpAddress
	swL3RelayDnsCtrlState	INTEGER

Defined Values

swL3MgmtMIB		1.3.6.1.4.1.171.11.133.5.1.3
The Structure of Layer 3 Network Management Information for the proprietary enterprise.
MODULE-IDENTITY

swL3IpMgmt		1.3.6.1.4.1.171.11.133.5.1.3.2
OBJECT IDENTIFIER

swL3RelayMgmt		1.3.6.1.4.1.171.11.133.5.1.3.3
OBJECT IDENTIFIER

swL3IpCtrlMgmt		1.3.6.1.4.1.171.11.133.5.1.3.2.1
OBJECT IDENTIFIER

swL3IpFdbMgmt		1.3.6.1.4.1.171.11.133.5.1.3.2.2
OBJECT IDENTIFIER

swL3RelayDnsMgmt		1.3.6.1.4.1.171.11.133.5.1.3.3.2
OBJECT IDENTIFIER

swL3IpCtrlTable		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3
This table contains IP interface information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3IpCtrlEntry

swL3IpCtrlEntry		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1
A list of information about a specific IP interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3IpCtrlEntry

swL3IpCtrlInterfaceName		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.1
This object indicates the name of the IP interface.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..12)

swL3IpCtrlIfIndex		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.2
This object uniquely identifies the IP interface number in the swL3IpCtrlTable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL3IpCtrlIpAddr		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.3
The IP address of the interface. This object only can take the value of the unicast IP address.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

swL3IpCtrlIpSubnetMask		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.4
The IP net mask for this interface.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

swL3IpCtrlVlanName		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.5
This object indicates the IP control entry's VLAN name. The VLAN name in each entry must be unique in the IP Control Table.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..32)

swL3IpCtrlProxyArp		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.6
This object indicates enable/disable of the proxy ARP function for IPv4.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3IpCtrlSecondary		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.7
When this is true(1), the IP address is the secondary IP. When false(2), the IP address is the primary IP.
Status: current	Access: read-create
OBJECT-TYPE
	TruthValue

swL3IpCtrlMode		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.8
This object indicates the IP operation mode. other(1) - This entry is currently in use but the conditions under which it will remain are determined by each of the following values. bootp(3) - The IP address will be set automatically from a BOOTP server. dhcp(4) - The IP address will be set automatically from a DHCP server.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), bootp(3), dhcp(4)

swL3IpCtrlAdminState		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.9
The state of the IP interface.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3IpCtrlIpv4AdminState		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.10
The IPv4 admin state of the IP interface. The default state is determined by project. This state will only be effective when the swL3IpCtrlAdminState is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3IpCtrlIpv6AdminState		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.12
The IPv6 admin state of the IP interface. The default state is determined by project. This state will only be effective when the swL3IpCtrlAdminState is enabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3IpCtrlIpv6LinkLocalAddress		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.14
The IPv6 link local address for this interface.
Status: current	Access: read-only
OBJECT-TYPE
	Ipv6Address

swL3IpCtrlIpv6LinkLocalPrefixLen		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.15
The IPv6 prefix length for this IPv6 link local address.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

swL3IpCtrlState		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.16
This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

swL3IpCtrlIpv6LinkLocalAutoState		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.17
The state of the IPv6 link local auto.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), enabled(2), disabled(3)

swL3IpCtrlLocalProxyArp		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.18
This object indicates enable/disable of the local proxy ARP function for IPv4.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3IpCtrlIpMtu		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.19
The MTU is the largest size of the IP datagram which may be transferred using a specific data link connection. The MTU value is a design parameter of a LAN and is a mutually agreed value (i.e. both ends of a link agree to use the same specific value) for most WAN links. The MTU range is based on the chip of the current device. The suggested minimum value is 1500 bytes. The suggested maximum value is the size of the jumbo frame minus 36. The suggested default setting is 1500 bytes.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER

swL3IpCtrlDhcpv6ClientState		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.20
The object indicates the state of the DHCPv6 client.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3IpCtrlIpDirectedBroadcastState		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.21
The object indicates the state of the IP Directed Broadcast.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3IpCtrlIpDhcpOption12State		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.22
Enable or disable insertion of option 12 in the DHCPDISCOVER and DHCPREQUEST message.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3IpCtrlIpDhcpOption12HostName		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.23
Specify the host name to be inserted in the DHCPDISCOVER and DHCPREQUEST message. The specified host name must start with a letter, end with a letter or digit, and have only letters, digits, and hyphen as interior characters; the maximal length is 63. By default, the host name is empty. When set an empty host name, means to clear the host name setting and use the default value to encode option 12.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..63)

swL3IpCtrlDhcpv6ClientPDState		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.24
The state of the Dhcpv6 Client PD.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3IpCtrlDhcpv6ClientPDPrefixName		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.25
This object indicates the name for the DHCPv6 Client PD. If the swL3IpCtrlDhcpv6ClientPDState is disabled, this object will be clear and can't write.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..12)

swL3IpCtrlDhcpv6ClientPDPrefix		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.26
The IPv6 prefix obtained form delegation router.
Status: current	Access: read-only
OBJECT-TYPE
	Ipv6Address

swL3IpCtrlDhcpv6ClientPDPrefixLen		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.27
The IPv6 prefix length for the prefix obtained from delegation router.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

swL3IpCtrlIpv6AutoConfigState		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.28
The state of IPv6 stateless adddress autoconfig.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3IpCtrlIpv6AutoConfigDefault		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.29
When this is true(1), a default route will be installed into ipv6 routing table. When false(2), no default route will be installed.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

swL3IpCtrlDhcpv6ClientRapidCommit		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.30
When this is true(1), Allows the two-message exchange method for address assignment.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

swL3IpCtrlDhcpv6ClientPDRapidCommit		1.3.6.1.4.1.171.11.133.5.1.3.2.1.3.1.31
When this is true(1), Allows the two-message exchange method for prefix assignment.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

swL3Ipv6CtrlTable		1.3.6.1.4.1.171.11.133.5.1.3.2.1.4
This table contains IPv6 information of an IP interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3Ipv6CtrlEntry

swL3Ipv6CtrlEntry		1.3.6.1.4.1.171.11.133.5.1.3.2.1.4.1
A list of IPv6 information about a specific IP interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3Ipv6CtrlEntry

swL3Ipv6CtrlInterfaceName		1.3.6.1.4.1.171.11.133.5.1.3.2.1.4.1.1
This object indicates the name of the IP interface.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..12)

swL3Ipv6CtrlMaxReassmblySize		1.3.6.1.4.1.171.11.133.5.1.3.2.1.4.1.2
Maximum Reassembly Size of the IP interface.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

swL3Ipv6CtrlNsRetransTimer		1.3.6.1.4.1.171.11.133.5.1.3.2.1.4.1.3
Neighbor solicitation's retransmit timer. The unit is set in milliseconds.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..4294967295

swL3Ipv6CtrlRaState		1.3.6.1.4.1.171.11.133.5.1.3.2.1.4.1.5
Neighbor solicited state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3Ipv6CtrlRaMinRtrAdvInterval		1.3.6.1.4.1.171.11.133.5.1.3.2.1.4.1.6
The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds. It must be no less than 3 seconds and no greater than .75 * MaxRtrAdvInterval. Default value: 0.33 * MaxRtrAdvInterval
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	3..1350

swL3Ipv6CtrlRaMaxRtrAdvInterval		1.3.6.1.4.1.171.11.133.5.1.3.2.1.4.1.7
The maximum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	4..1800

swL3Ipv6CtrlRaLifeTime		1.3.6.1.4.1.171.11.133.5.1.3.2.1.4.1.8
Indicates the lifetime of the router as the default router.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..9000

swL3Ipv6CtrlRaReachableTime		1.3.6.1.4.1.171.11.133.5.1.3.2.1.4.1.9
Indicates the amount of time that a node can consider a neighboring node reachable after receiving a reachability confirmation.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..3600000

swL3Ipv6CtrlRaRetransTime		1.3.6.1.4.1.171.11.133.5.1.3.2.1.4.1.10
Indicates the amount of time between retransmissions of neighbor solicited messages. The unit is set in millisecond.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..4294967295

swL3Ipv6CtrlRaHopLimit		1.3.6.1.4.1.171.11.133.5.1.3.2.1.4.1.11
Indicates the default value of the hop limit field in the IPv6 header for packets sent by hosts that receive this RA message.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

swL3Ipv6CtrlRaManagedFlag		1.3.6.1.4.1.171.11.133.5.1.3.2.1.4.1.12
When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an address in the addition to the addresses derived from the stateless address configuration.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3Ipv6CtrlRaOtherConfigFlag		1.3.6.1.4.1.171.11.133.5.1.3.2.1.4.1.13
When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an on-link address configuration information.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3Ipv6CtrlDadRetransNum		1.3.6.1.4.1.171.11.133.5.1.3.2.1.4.1.14
Indicates the value of duplicate address detection attempt number
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

swL3Ipv6AddressCtrlTable		1.3.6.1.4.1.171.11.133.5.1.3.2.1.5
This table contains IPv6 address information for each IP interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3Ipv6AddressCtrlEntry

swL3Ipv6AddressCtrlEntry		1.3.6.1.4.1.171.11.133.5.1.3.2.1.5.1
A list of information about a specific IPv6 address.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3Ipv6AddressCtrlEntry

swL3Ipv6AddressCtrlInterfaceName		1.3.6.1.4.1.171.11.133.5.1.3.2.1.5.1.1
This object indicates the name of the IP interface.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..12)

swL3Ipv6Address		1.3.6.1.4.1.171.11.133.5.1.3.2.1.5.1.2
Specify the IPv6 address.
Status: current	Access: read-only
OBJECT-TYPE
	Ipv6Address

swL3Ipv6AddressCtrlPrefixLen		1.3.6.1.4.1.171.11.133.5.1.3.2.1.5.1.3
Indicates the prefix length of this IPv6 address.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

swL3Ipv6AddressCtrlPreferredLifeTime		1.3.6.1.4.1.171.11.133.5.1.3.2.1.5.1.4
Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains in preferred state. For an infinite valid lifetime, the value can be set to 0xffffffff.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..4294967294

swL3Ipv6AddressCtrlValidLifeTime		1.3.6.1.4.1.171.11.133.5.1.3.2.1.5.1.5
Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains valid. For an infinite valid lifetime, the value can be set to 0xffffffff.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..4294967294

swL3Ipv6AddressCtrlOnLinkFlag		1.3.6.1.4.1.171.11.133.5.1.3.2.1.5.1.6
When enabled, the address implied by the specified prefix is available on the link where the RA message is received.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3Ipv6AddressCtrlAutonomousFlag		1.3.6.1.4.1.171.11.133.5.1.3.2.1.5.1.7
When enabled, the specified prefix will be used to create an autonomous address configuration.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3Ipv6AddressCtrlState		1.3.6.1.4.1.171.11.133.5.1.3.2.1.5.1.8
This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

swL3Ipv6AddressCtrlAddressType		1.3.6.1.4.1.171.11.133.5.1.3.2.1.5.1.9
This object indicates the type of the IPv6 address. manual(1): the IPv6 address is configured by user. dhcpv6(2): the IPv6 address is assigned by DHCPv6 server. stateless(3): the IPv6 address is assigned by router advertisement.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	manual(1), dhcpv6(2), stateless(3)

swL3Ipv6DHCPv6CPDAddrCtrlTable		1.3.6.1.4.1.171.11.133.5.1.3.2.1.6
This table contain the information of the IPv6 address which based on DHCPv6 client PD.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3Ipv6DHCPv6CPDAddrCtrlEntry

swL3Ipv6DHCPv6CPDAddrCtrlEntry		1.3.6.1.4.1.171.11.133.5.1.3.2.1.6.1
A list of information about a specific DHCPv6 Client PD IPv6 address.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3Ipv6DHCPv6CPDAddrCtrlEntry

swL3Ipv6DHCPv6CPDAddrCtrlInterfaceName		1.3.6.1.4.1.171.11.133.5.1.3.2.1.6.1.1
This object indicates the name of the IP interface.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..12)

swL3Ipv6DHCPv6CPDAddrCtrlPrefixName		1.3.6.1.4.1.171.11.133.5.1.3.2.1.6.1.2
This object indicates the name of the prefix based on which the IPv6 address will be generate.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..12)

swL3Ipv6DHCPv6CPDAddrCtrlIPv6addr		1.3.6.1.4.1.171.11.133.5.1.3.2.1.6.1.3
Specify the suffix of the IPv6 address.
Status: current	Access: read-only
OBJECT-TYPE
	Ipv6Address

swL3Ipv6DHCPv6CPDAddrCtrlPrefixLen		1.3.6.1.4.1.171.11.133.5.1.3.2.1.6.1.4
Indicates the prefix length of this IPv6 address.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

swL3Ipv6DHCPv6CPDAddrCtrlState		1.3.6.1.4.1.171.11.133.5.1.3.2.1.6.1.5
This variable displays the status of the entry. The status is used for creating and deleting instances of the objects in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

swL3IpCtrlAllIpIfState		1.3.6.1.4.1.171.11.133.5.1.3.2.1.7
This object indicates all interface function state of the device. (except the loopback interface)
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), enabled(2), disabled(3)

swL3LoopBackIpCtrlTable		1.3.6.1.4.1.171.11.133.5.1.3.2.1.8
This table contains loopback IP interface information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3LoopBackIpCtrlEntry

swL3LoopBackIpCtrlEntry		1.3.6.1.4.1.171.11.133.5.1.3.2.1.8.1
A list of information about a specific loopback IP interface.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3LoopBackIpCtrlEntry

swL3LoopBackIpCtrlInterfaceName		1.3.6.1.4.1.171.11.133.5.1.3.2.1.8.1.1
This object indicates the name of the loopback IP interface.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..12)

swL3LoopBackIpCtrlIfIndex		1.3.6.1.4.1.171.11.133.5.1.3.2.1.8.1.2
This object uniquely identifies the loopback IP interface number in the swL3LoopBackIpCtrlTable.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL3LoopBackIpCtrlIpAddr		1.3.6.1.4.1.171.11.133.5.1.3.2.1.8.1.3
The IP address of the loopback interface. This object only can take the value of the unicast IP address.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

swL3LoopBackIpCtrlIpSubnetMask		1.3.6.1.4.1.171.11.133.5.1.3.2.1.8.1.4
The IP net mask for this loopback interface.
Status: current	Access: read-create
OBJECT-TYPE
	IpAddress

swL3LoopBackIpCtrlAdminState		1.3.6.1.4.1.171.11.133.5.1.3.2.1.8.1.5
The state of the loopback IP interface.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL3LoopBackIpCtrlRowStatus		1.3.6.1.4.1.171.11.133.5.1.3.2.1.8.1.6
This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

swL3IpFdbInfoTable		1.3.6.1.4.1.171.11.133.5.1.3.2.2.1
A table that contains forwarding and/or filtering information. This information is used by the switch in determining how to propagate the received IP packets.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3IpFdbInfoEntry

swL3IpFdbInfoEntry		1.3.6.1.4.1.171.11.133.5.1.3.2.2.1.1
Information about a specific IP address for which the bridge has some forwarding and/or filtering information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3IpFdbInfoEntry

swL3IpFdbInfoIpAddr		1.3.6.1.4.1.171.11.133.5.1.3.2.2.1.1.1
A IP address for which switch has forwarding and/or filtering information.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

swL3IpFdbInfoIpSubnetMask		1.3.6.1.4.1.171.11.133.5.1.3.2.2.1.1.2
A IP net mask for this interface for which the switch has forwarding and/or filtering information.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

swL3IpFdbInfoPort		1.3.6.1.4.1.171.11.133.5.1.3.2.2.1.1.3
Either the value '0', or the port number of the port on which packet having a IP address equal to the value of the corresponding instance of swL3IpFdbInfoIpAddr has been seen. A value of '0' indicates that the port number has not been learned but that switch does have some forwarding/filtering information about this address.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL3IpFdbInfoType		1.3.6.1.4.1.171.11.133.5.1.3.2.2.1.1.4
The status of this entry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), static(2), dynamic(3)

swL3IpArpAgingTime		1.3.6.1.4.1.171.11.133.5.1.3.2.4
The timeout period in minutes for aging out dynamically learned ARP information.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

swL3IpStaticRouteTable		1.3.6.1.4.1.171.11.133.5.1.3.2.5
This entity's IP static Routing table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3IpStaticRouteEntry

swL3IpStaticRouteEntry		1.3.6.1.4.1.171.11.133.5.1.3.2.5.1
A particular route to a particular destination, under a particular policy. Once an entry is built,it shouldn't be modified.That is,it just supports create and delete actions.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3IpStaticRouteEntry

swL3IpStaticRouteDest		1.3.6.1.4.1.171.11.133.5.1.3.2.5.1.1
The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteMask object is not equal to x.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

swL3IpStaticRouteMask		1.3.6.1.4.1.171.11.133.5.1.3.2.5.1.2
Indicate the mask to be logical-AND with the destination address before being compared to the value in the swL3IpStaticRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the swL3IpStaticRouteMask by reference to the IP Address Class. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the swL3IpStaticRouteDest object is not equal to swL3IpStaticRouteDest.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

swL3IpStaticRouteBkupState		1.3.6.1.4.1.171.11.133.5.1.3.2.5.1.3
The routing state for this route.The value SHOULD be primary(1), backup(2) or none(3).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	primary(1), backup(2), none(3)

swL3IpStaticRouteNextHop		1.3.6.1.4.1.171.11.133.5.1.3.2.5.1.4
Specifies the IP address for the next hop router. An IP address of 255.255.255.255 denotes a Null interface as the next hop.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

swL3IpStaticRouteMetric		1.3.6.1.4.1.171.11.133.5.1.3.2.5.1.5
Specifies the routing metric for this route.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..65535

swL3IpStaticRouteStatus		1.3.6.1.4.1.171.11.133.5.1.3.2.5.1.6
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry resides in the table. active(4) - the nextHop of this entry exists in the ARP table. inActive(5) - the next hop of this entry does not exist in the ARP table.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	other(1), invalid(2), valid(3), active(4), inActive(5)

swL3IpStaticRouteWeight		1.3.6.1.4.1.171.11.133.5.1.3.2.5.1.7
Specifies the weight value. Used for the weighted multipath.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..4

swL3IpStaticRouteInterfaceName		1.3.6.1.4.1.171.11.133.5.1.3.2.5.1.8
Specifies the name of the IP interface.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

swL3IpStaticRouteCost		1.3.6.1.4.1.171.11.133.5.1.3.2.5.1.9
Specifies the cost of the Route Entry.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

swL3RelayDnsState		1.3.6.1.4.1.171.11.133.5.1.3.3.2.1
This object indicates if the DNS Relay function is enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL3RelayDnsPrimaryServer		1.3.6.1.4.1.171.11.133.5.1.3.3.2.2
This object indicates the address of the primary DNS server.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

swL3RelayDnsSecondaryServer		1.3.6.1.4.1.171.11.133.5.1.3.3.2.3
This object indicates the address of the secondary DNS server.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

swL3RelayDnsCacheState		1.3.6.1.4.1.171.11.133.5.1.3.3.2.4
This object indicates DNS Relay cache is enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL3RelayDnsStaticTableState		1.3.6.1.4.1.171.11.133.5.1.3.3.2.5
This object indicates DNS Relay static table is enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL3RelayDnsCtrlTable		1.3.6.1.4.1.171.11.133.5.1.3.3.2.6
This table displays the current DNS relay static table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL3RelayDnsCtrlEntry

swL3RelayDnsCtrlEntry		1.3.6.1.4.1.171.11.133.5.1.3.3.2.6.1
A list of information display the current DNS relay static table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL3RelayDnsCtrlEntry

swL3RelayDnsCtrlDomainName		1.3.6.1.4.1.171.11.133.5.1.3.3.2.6.1.1
The domain name of the entry.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..32)

swL3RelayDnsCtrlIpAddr		1.3.6.1.4.1.171.11.133.5.1.3.3.2.6.1.2
The IP address of the entry.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

swL3RelayDnsCtrlState		1.3.6.1.4.1.171.11.133.5.1.3.3.2.6.1.3
This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(2) - writing this value to the object, and then the corresponding entry will be removed from the table. valid(3) - this entry is reside in the table.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), invalid(2), valid(3)