DGS3000-28SC-L2MGMT-MIB

File: DGS3000-28SC-L2MGMT-MIB.mib (106468 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	RFC1155-SMI
DLINK-ID-REC-MIB	SWDGS3000PRIMGMT-MIB	PORT-SECURITY-MIB
IEEE8021-CFM-MIB

Imported symbols

IpAddress	TimeTicks	Integer32
Unsigned32	MODULE-IDENTITY	OBJECT-TYPE
DisplayString	RowStatus	TruthValue
Counter	AgentNotifyLevel	TEXTUAL-CONVENTION
dlink-Dgs3000Proj-DGS3000-28SCax	swPortSecPortIndex	dot1agCfmMdIndex
dot1agCfmMaIndex	dot1agCfmMepIdentifier

Defined Types

MacAddress
OCTET STRING	Size(6)

VlanId
INTEGER	1..4094

PortList
OCTET STRING	Size(0..127)

IANAifMauAutoNegCapBits
This data type is used as the syntax of the swL2PortAutoNegCapabilityBits, swL2PortAutoNegCapAdvertisedBits, and swL2PortAutoNegCapReceivedBits objects in swL2PortAutoNegTable.
TEXTUAL-CONVENTION
	BITS	bOther(0), b10baseT(1), b10baseTFD(2), b100baseT4(3), b100baseTX(4), b100baseTXFD(5), b100baseT2(6), b100baseT2FD(7), bFdxPause(8), bFdxAPause(9), bFdxSPause(10), bFdxBPause(11), b1000baseX(12), b1000baseXFD(13), b1000baseT(14), b1000baseTFD(15)

SwDevModuleInfoEntry
SEQUENCE
	swDevModuleInfoUnitID	INTEGER
	swDevModuleInfoModuleName	DisplayString
	swDevModuleInfoReversion	DisplayString
	swDevModuleInfoSerial	DisplayString
	swDevModuleInfoDescription	DisplayString

SwL2DevCtrlCFMPortEntry
SEQUENCE
	swL2DevCtrlCFMPortIndex	INTEGER
	swL2DevCtrlCFMPortState	INTEGER

SwL2DevCtrlCFMMaEntry
SEQUENCE
	swL2DevCtrlCFMMaMode	INTEGER

SwL2DevCtrlCFMMepEntry
SEQUENCE
	swL2DevCtrlCFMMepMode	INTEGER

SwL2VlanStaticEntry
SEQUENCE
	swL2VlanIndex	VlanId
	swL2VLANAdvertisement	INTEGER

SwL2VlanPortInfoEntry
SEQUENCE
	swL2VlanPortInfoPortIndex	INTEGER
	swL2VlanPortInfoVid	VlanId
	swL2VlanPortInfoPortRole	INTEGER

SwL2SubnetVLANEntry
SEQUENCE
	swL2SubnetVLANIPAddress	IpAddress
	swL2SubnetVLANIPMask	IpAddress
	swL2SubnetVLANID	VlanId
	swL2SubnetVLANPriority	INTEGER
	swL2SubnetVLANRowStatus	RowStatus

SwL2VlanPrecedenceEntry
SEQUENCE
	swL2VlanPrecedencePortIndex	INTEGER
	swL2VlanPrecedenceClassification	INTEGER

SwL2PortInfoEntry
SEQUENCE
	swL2PortInfoPortIndex	INTEGER
	swL2PortInfoMediumType	INTEGER
	swL2PortInfoUnitID	INTEGER
	swL2PortInfoType	INTEGER
	swL2PortInfoLinkStatus	INTEGER
	swL2PortInfoNwayStatus	INTEGER
	swL2PortInfoModuleType	INTEGER
	swL2PortInfoErrorDisabled	INTEGER

SwL2PortCtrlEntry
SEQUENCE
	swL2PortCtrlPortIndex	INTEGER
	swL2PortCtrlMediumType	INTEGER
	swL2PortCtrlUnitIndex	INTEGER
	swL2PortCtrlAdminState	INTEGER
	swL2PortCtrlNwayState	INTEGER
	swL2PortCtrlFlowCtrlState	INTEGER
	swL2PortCtrlLearningState	INTEGER
	swL2PortCtrlMACNotifyState	INTEGER
	swL2PortCtrlMDIXState	INTEGER
	swL2PortCtrlAutoNegRestart	INTEGER
	swL2PortCtrlAutoNegCapAdvertisedBits	IANAifMauAutoNegCapBits

SwL2PortCableDiagnosisEntry
SEQUENCE
	swL2PortCableDiagnosisPortIndex	INTEGER
	swL2PortCableDiagnosisPairIndex	INTEGER
	swL2PortCableDiagnosisCableStatus	INTEGER
	swL2PortCableDiagnosisPairStatus	INTEGER
	swL2PortCableDiagnosisPairLength	INTEGER
	swL2PortCableDiagnosisPairLengthInaccuracy	INTEGER

SwL2PortCounterCtrlEntry
SEQUENCE
	swL2PortCounterCtrlPortIndex	INTEGER
	swL2PortCounterClearCtrl	INTEGER

SwL2PortErrEntry
SEQUENCE
	swL2PortErrPortIndex	INTEGER
	swL2PortErrPortState	INTEGER
	swL2PortErrPortConnStatus	INTEGER
	swL2PortErrPortReason	INTEGER

SwL2PortAutoNegInfoEntry
SEQUENCE
	swL2PortAutoNegInfoPortIndex	INTEGER
	swL2PortAutoNegInfoAdminStatus	INTEGER
	swL2PortAutoNegInfoCapabilityBits	IANAifMauAutoNegCapBits
	swL2PortAutoNegInfoCapAdvertisedBits	IANAifMauAutoNegCapBits
	swL2PortAutoNegInfoCapReceivedBits	IANAifMauAutoNegCapBits

SwL2PortDropCounterEntry
SEQUENCE
	swL2PortDropCounterPortIndex	INTEGER
	swL2PortBufferFullDrops	Counter
	swL2PortACLDrops	Counter
	swL2PortMulticastDrops	Counter
	swL2PortVLANIngressDrops	Counter
	swL2PortIngressBandwidthControlDrops	Counter
	swL2PortInvalidIPv6Drops	Counter
	swL2PortSTPDrops	Counter
	swL2PortStormAndFDBDiscard	Counter
	swL2PortMTUDrops	Counter
	swL2PortInvalidDestinationPort	Counter

SwL2PortJumboFrameCtrlEntry
SEQUENCE
	swL2PortJumboFrameCtrlPortIndex	INTEGER
	swL2PortJumboFrameCtrlState	INTEGER

SwL2PortSfpInfoEntry
SEQUENCE
	swL2PortSfpInfoPortIndex	INTEGER
	swL2PortSfpInfoConnectType	DisplayString
	swL2PortSfpInfoVendorName	DisplayString
	swL2PortSfpInfoVendorPN	DisplayString
	swL2PortSfpInfoVendorSN	DisplayString
	swL2PortSfpInfoVendorOUI	DisplayString
	swL2PortSfpInfoVendorRev	DisplayString
	swL2PortSfpInfoDateCode	DisplayString
	swL2PortSfpInfoFiberType	DisplayString
	swL2PortSfpInfoBaudRate	INTEGER
	swL2PortSfpInfoWavelength	INTEGER

SwL2PortLinkTimeEntry
SEQUENCE
	swL2PortLinkTimeIfIndex	INTEGER
	swL2PortLinkTimer	TimeTicks

SwL2TrunkCtrlEntry
SEQUENCE
	swL2TrunkIndex	INTEGER
	swL2TrunkName	DisplayString
	swL2TrunkMasterPort	INTEGER
	swL2TrunkMember	PortList
	swL2TrunkFloodingPort	INTEGER
	swL2TrunkType	INTEGER
	swL2TrunkState	RowStatus

SwL2TrunkLACPPortEntry
SEQUENCE
	swL2TrunkLACPPortIndex	INTEGER
	swL2TrunkLACPPortState	INTEGER

SwL2TrunkVLANEntry
SEQUENCE
	swL2TrunkVLANPort	INTEGER
	swL2TrunkVLANState	INTEGER

SwL2MirrorGroupEntry
SEQUENCE
	swL2MirrorGroupID	INTEGER
	swL2MirrorGroupRowStatus	RowStatus
	swL2MirrorGroupState	INTEGER
	swL2MirrorGroupTargetPort	INTEGER
	swL2MirrorGroupSourceIngress	PortList
	swL2MirrorGroupSourceEgress	PortList

SwL2IGMPAccessAuthEntry
SEQUENCE
	swL2IGMPAccessAuthPort	INTEGER
	swL2IGMPAccessAuthState	INTEGER

SwL2TrafficCtrlEntry
SEQUENCE
	swL2TrafficCtrlGroupIndex	INTEGER
	swL2TrafficCtrlUnitIndex	INTEGER
	swL2TrafficCtrlBMStromthreshold	INTEGER
	swL2TrafficCtrlBcastStromCtrl	INTEGER
	swL2TrafficCtrlMcastStromCtrl	INTEGER
	swL2TrafficCtrlDlfStromCtrl	INTEGER

SwL2TrafficSegEntry
SEQUENCE
	swL2TrafficSegPort	INTEGER
	swL2TrafficSegForwardPorts	PortList

SwL2MulticastFilterModeVlanEntry
SEQUENCE
	swL2MulticastFilterVid	INTEGER
	swL2MulticastFilterVlanMode	INTEGER

SwL2MulticastFilterModePortEntry
SEQUENCE
	swL2MulticastFilterPortIndex	INTEGER
	swL2MulticastFilterPortMode	INTEGER

SwL2LoopDetectPortEntry
SEQUENCE
	swL2LoopDetectPortIndex	INTEGER
	swL2LoopDetectPortState	INTEGER
	swL2LoopDetectPortLoopVLAN	DisplayString
	swL2LoopDetectPortLoopStatus	INTEGER

Defined Values

swL2MgmtMIB		1.3.6.1.4.1.171.11.133.5.1.2
The Structure of Layer 2 Network Management Information.
MODULE-IDENTITY

swL2DevMgmt		1.3.6.1.4.1.171.11.133.5.1.2.1
OBJECT IDENTIFIER

swL2VLANMgmt		1.3.6.1.4.1.171.11.133.5.1.2.2
OBJECT IDENTIFIER

swL2PortMgmt		1.3.6.1.4.1.171.11.133.5.1.2.3
OBJECT IDENTIFIER

swL2TrunkMgmt		1.3.6.1.4.1.171.11.133.5.1.2.9
OBJECT IDENTIFIER

swL2MirrorMgmt		1.3.6.1.4.1.171.11.133.5.1.2.10
OBJECT IDENTIFIER

swL2IGMPMgmt		1.3.6.1.4.1.171.11.133.5.1.2.11
OBJECT IDENTIFIER

swL2TrafficMgmt		1.3.6.1.4.1.171.11.133.5.1.2.13
OBJECT IDENTIFIER

swL2TrafficSegMgmt		1.3.6.1.4.1.171.11.133.5.1.2.14
OBJECT IDENTIFIER

swL2MulticastFilterMode		1.3.6.1.4.1.171.11.133.5.1.2.17
OBJECT IDENTIFIER

swL2LoopDetectMgmt		1.3.6.1.4.1.171.11.133.5.1.2.18
OBJECT IDENTIFIER

swL2MgmtMIBTraps		1.3.6.1.4.1.171.11.133.5.1.2.100
OBJECT IDENTIFIER

swL2DevInfo		1.3.6.1.4.1.171.11.133.5.1.2.1.1
OBJECT IDENTIFIER

swDevInfoTotalNumOfPort		1.3.6.1.4.1.171.11.133.5.1.2.1.1.1
The number of ports within this switch. This value is the sum of the ports within this switch.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swDevInfoNumOfPortInUse		1.3.6.1.4.1.171.11.133.5.1.2.1.1.2
The number of ports in this switch connected to the segment or the end stations.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swDevModuleInfoTable		1.3.6.1.4.1.171.11.133.5.1.2.1.1.3
This table contains the module information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwDevModuleInfoEntry

swDevModuleInfoEntry		1.3.6.1.4.1.171.11.133.5.1.2.1.1.3.1
A list of management information for each unit in the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwDevModuleInfoEntry

swDevModuleInfoUnitID		1.3.6.1.4.1.171.11.133.5.1.2.1.1.3.1.1
This object indicates the specific unit ID in the stacking/chassis table.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..12

swDevModuleInfoModuleName		1.3.6.1.4.1.171.11.133.5.1.2.1.1.3.1.3
A text string containing the name of the module.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..12)

swDevModuleInfoReversion		1.3.6.1.4.1.171.11.133.5.1.2.1.1.3.1.4
A text string containing the version (name or number) of the module.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..4)

swDevModuleInfoSerial		1.3.6.1.4.1.171.11.133.5.1.2.1.1.3.1.5
A text string containing the serial number or serial name of the module.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..9)

swDevModuleInfoDescription		1.3.6.1.4.1.171.11.133.5.1.2.1.1.3.1.6
A text string containing a description of the module.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..32)

swL2DevCtrl		1.3.6.1.4.1.171.11.133.5.1.2.1.2
OBJECT IDENTIFIER

swL2DevCtrlStpState		1.3.6.1.4.1.171.11.133.5.1.2.1.2.1
This object can enable or disable the spanning tree algorithm during the runtime of the system.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL2DevCtrlIGMPSnooping		1.3.6.1.4.1.171.11.133.5.1.2.1.2.2
This object indicates if the layer 2 Internet Group Management Protocol (IGMP) capture function is enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL2DevCtrlIGMPSnoopingMcstRTOnly		1.3.6.1.4.1.171.11.133.5.1.2.1.2.3
This object controls the IGMP snooping forward multicast routing only state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL2DevCtrlRmonState		1.3.6.1.4.1.171.11.133.5.1.2.1.2.4
This object can enable or disable RMON.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL2DevCtrlSnmpTrapState		1.3.6.1.4.1.171.11.133.5.1.2.1.2.5
This object controls the SNMP trap status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL2DevCtrlCleanAllStatisticCounter		1.3.6.1.4.1.171.11.133.5.1.2.1.2.6
When the object is set to active, all statistical counters will be cleared. If set to normal, no action will occur.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	normal(1), active(2)

swL2DevCtrlVlanIdOfFDBTbl		1.3.6.1.4.1.171.11.133.5.1.2.1.2.7
Indicates the VLAN ID to which the Dot1dTpFdbTable belongs; The default value is the DEFAULT_VLAN_ID of the system.
Status: current	Access: read-write
OBJECT-TYPE
	VlanId

swL2MACNotifyState		1.3.6.1.4.1.171.11.133.5.1.2.1.2.8
This object can enable or disable MAC Notification.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL2MACNotifyHistorySize		1.3.6.1.4.1.171.11.133.5.1.2.1.2.9
This object indicates the history size of MAC addresses in the MAC Address table. The default value is 1.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..500

swL2MACNotifyInterval		1.3.6.1.4.1.171.11.133.5.1.2.1.2.10
This object indicates the time interval, in seconds, that will trigger MAC notification messages.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..2147483647

swL2DevCtrlAsymVlanState		1.3.6.1.4.1.171.11.133.5.1.2.1.2.13
This object enables or disables asymmetric VLANs during the runtime of the system.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL2DevCtrlTelnet		1.3.6.1.4.1.171.11.133.5.1.2.1.2.14
OBJECT IDENTIFIER

swL2DevCtrlTelnetState		1.3.6.1.4.1.171.11.133.5.1.2.1.2.14.1
This object controls the Telnet status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL2DevCtrlTelnetTcpPort		1.3.6.1.4.1.171.11.133.5.1.2.1.2.14.2
This object designates TCP ports. When Telnet is disabled, this object is not accessible.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

swL2DevCtrlManagementVlanId		1.3.6.1.4.1.171.11.133.5.1.2.1.2.16
This object controls which previously created VLANs are included in the System IP Interface.
Status: current	Access: read-write
OBJECT-TYPE
	VlanId

swL2DevCtrlWeb		1.3.6.1.4.1.171.11.133.5.1.2.1.2.17
OBJECT IDENTIFIER

swL2DevCtrlWebState		1.3.6.1.4.1.171.11.133.5.1.2.1.2.17.1
This object controls the Web status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL2DevCtrlWebTcpPort		1.3.6.1.4.1.171.11.133.5.1.2.1.2.17.2
This object designates TCP ports. When Web is disabled, this object is not accessible.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

swL2DevCtrlLLDPState		1.3.6.1.4.1.171.11.133.5.1.2.1.2.18
Specifies the state of the LLDP function. When this function is enabled, the switch can start to transmit LLDP packets and receive and process the LLDP packets. The specific function of each port will depend on the per port LLDP setting. For the advertisement of LLDP packets, the switch announces the information to its neighbor through ports. For receiving LLDP packets, the switch will learn the information from the LLDP packets advertised from the neighbor in the neighbor table.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL2DevCtrlLLDPForwardMessageState		1.3.6.1.4.1.171.11.133.5.1.2.1.2.19
When lldp is disabled and lldp forward_message's are enabled, the LLDP Data Unit packets received by the switch will be forwarded.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL2DevCtrlIpAutoconfig		1.3.6.1.4.1.171.11.133.5.1.2.1.2.20
This object controls the IP auto configuration state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL2DevCtrlCFM		1.3.6.1.4.1.171.11.133.5.1.2.1.2.21
OBJECT IDENTIFIER

swL2DevCtrlCFMState		1.3.6.1.4.1.171.11.133.5.1.2.1.2.21.1
This object indicates the CFM global state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL2DevCtrlCFMPortTable		1.3.6.1.4.1.171.11.133.5.1.2.1.2.21.2
A table containing the CFM state of specified ports.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2DevCtrlCFMPortEntry

swL2DevCtrlCFMPortEntry		1.3.6.1.4.1.171.11.133.5.1.2.1.2.21.2.1
The entry of the CFM state on specified ports.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2DevCtrlCFMPortEntry

swL2DevCtrlCFMPortIndex		1.3.6.1.4.1.171.11.133.5.1.2.1.2.21.2.1.1
This object indicates the port number.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

swL2DevCtrlCFMPortState		1.3.6.1.4.1.171.11.133.5.1.2.1.2.21.2.1.2
This object indicates the CFM state by port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL2DevCtrlCFMMaTable		1.3.6.1.4.1.171.11.133.5.1.2.1.2.21.3
A table containing the CFM mode of specified MAs.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2DevCtrlCFMMaEntry

swL2DevCtrlCFMMaEntry		1.3.6.1.4.1.171.11.133.5.1.2.1.2.21.3.1
The entry of the CFM mode on specified MAs.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2DevCtrlCFMMaEntry

swL2DevCtrlCFMMaMode		1.3.6.1.4.1.171.11.133.5.1.2.1.2.21.3.1.1
This object indicates the CFM mode by MA.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	software(1), hardware(2)

swL2DevCtrlCFMMepTable		1.3.6.1.4.1.171.11.133.5.1.2.1.2.21.4
A table containing the CFM mode of specified MEPs.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2DevCtrlCFMMepEntry

swL2DevCtrlCFMMepEntry		1.3.6.1.4.1.171.11.133.5.1.2.1.2.21.4.1
The entry of the CFM mode on specified MEPs.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2DevCtrlCFMMepEntry

swL2DevCtrlCFMMepMode		1.3.6.1.4.1.171.11.133.5.1.2.1.2.21.4.1.1
This object indicates the CFM mode by MEP.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	software(1), hardware(2)

swL2DevCtrlVLANTrunkState		1.3.6.1.4.1.171.11.133.5.1.2.1.2.22
This indicates the global state of the VLAN trunking feature of the device.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL2DevCtrlIpAutoconfigTimeout		1.3.6.1.4.1.171.11.133.5.1.2.1.2.23
This object indicates the timeout for the auto configuration.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

swL2DevAlarm		1.3.6.1.4.1.171.11.133.5.1.2.1.3
OBJECT IDENTIFIER

swL2DevAlarmNewRoot		1.3.6.1.4.1.171.11.133.5.1.2.1.3.1
When the device has become the new root of the Spanning Tree, this object decides whether to send a new root trap.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL2DevAlarmTopologyChange		1.3.6.1.4.1.171.11.133.5.1.2.1.3.2
This object determines whether or not to send a trap message when the switch topology changes. If the object is enabled (3), the Topology Change trap is sent by the device when any of its configured ports transition from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port transition, the device does not send the trap if this object value is disabled or in another state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL2DevAlarmLinkChange		1.3.6.1.4.1.171.11.133.5.1.2.1.3.3
This object determines whether or not to send a trap message when the link changes. If the object is enabled (3), the Link Change trap is sent by the device when any of its port links change. The device does not send the trap if this object value is disabled or in another state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL2VlanStaticTable		1.3.6.1.4.1.171.11.133.5.1.2.2.1
A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2VlanStaticEntry

swL2VlanStaticEntry		1.3.6.1.4.1.171.11.133.5.1.2.2.1.1
Static information for a VLAN configured into this device by (local or network) management.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2VlanStaticEntry

swL2VlanIndex		1.3.6.1.4.1.171.11.133.5.1.2.2.1.1.1
The VLAN-ID or other identifier referring to this VLAN.
Status: current	Access: not-accessible
OBJECT-TYPE
	VlanId

swL2VLANAdvertisement		1.3.6.1.4.1.171.11.133.5.1.2.2.1.1.2
This object indicates if the advertisement is active or not.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL2PVIDAutoAssignmentState		1.3.6.1.4.1.171.11.133.5.1.2.2.2
This object controls the PVID auto assignment state. If 'Auto-assign PVID' is disabled, the PVID can only be changed by PVID configuration (user changes explicitly). The VLAN configuration will not automatically change the PVID. If 'Auto-assign PVID' is enabled, the PVID will be changed by PVID or VLAN configuration. When a user configures a port to VLAN X's untagged membership, this port's PVID will be updated with VLAN X. Using the VLAN list command, PVID is updated as the last item of the VLAN list. When a user removes a port from the untagged membership of the PVID's VLAN, the port's PVID will be assigned 'default VLAN'.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL2VlanPortInfoTable		1.3.6.1.4.1.171.11.133.5.1.2.2.3
A table containing the VLAN and port role information of each port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2VlanPortInfoEntry

swL2VlanPortInfoEntry		1.3.6.1.4.1.171.11.133.5.1.2.2.3.1
The table entry of VLAN port information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2VlanPortInfoEntry

swL2VlanPortInfoPortIndex		1.3.6.1.4.1.171.11.133.5.1.2.2.3.1.1
The port index.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2VlanPortInfoVid		1.3.6.1.4.1.171.11.133.5.1.2.2.3.1.2
The VLAN ID assigned to a special port
Status: current	Access: read-only
OBJECT-TYPE
	VlanId

swL2VlanPortInfoPortRole		1.3.6.1.4.1.171.11.133.5.1.2.2.3.1.3
The port role of a special port. When the role is 'other', it means this port does not belong to the VLAN.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), untagged(2), tagged(3), dynamic(4), forbidden(5)

swL2SubnetVLANTable		1.3.6.1.4.1.171.11.133.5.1.2.2.4
A table containing the subnet VLAN information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2SubnetVLANEntry

swL2SubnetVLANEntry		1.3.6.1.4.1.171.11.133.5.1.2.2.4.1
The entry of subnet VLAN information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2SubnetVLANEntry

swL2SubnetVLANIPAddress		1.3.6.1.4.1.171.11.133.5.1.2.2.4.1.1
This object indicates the IP address.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

swL2SubnetVLANIPMask		1.3.6.1.4.1.171.11.133.5.1.2.2.4.1.2
This object indicates the IP mask.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

swL2SubnetVLANID		1.3.6.1.4.1.171.11.133.5.1.2.2.4.1.3
This object indicates the VLAN ID.
Status: current	Access: read-create
OBJECT-TYPE
	VlanId

swL2SubnetVLANPriority		1.3.6.1.4.1.171.11.133.5.1.2.2.4.1.4
This object indicates the priority.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..7

swL2SubnetVLANRowStatus		1.3.6.1.4.1.171.11.133.5.1.2.2.4.1.5
This object indicates the status of this entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

swL2VlanPrecedenceTable		1.3.6.1.4.1.171.11.133.5.1.2.2.5
A table containing the VLAN classification precedence information of each port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2VlanPrecedenceEntry

swL2VlanPrecedenceEntry		1.3.6.1.4.1.171.11.133.5.1.2.2.5.1
The entry of VLAN classification precedence information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2VlanPrecedenceEntry

swL2VlanPrecedencePortIndex		1.3.6.1.4.1.171.11.133.5.1.2.2.5.1.1
This object indicates the port index.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2VlanPrecedenceClassification		1.3.6.1.4.1.171.11.133.5.1.2.2.5.1.2
This object indicates the VLAN classification precedence.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	mac-based(1), subnet-based(2)

swL2NniGvrpBpduAddress		1.3.6.1.4.1.171.11.133.5.1.2.2.6
Specifies the GVRP's BPDU MAC address of the NNI port with Q-in-Q status.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	dot1d(1), dot1ad(2)

swL2PortInfoTable		1.3.6.1.4.1.171.11.133.5.1.2.3.1
A table that contains information about every port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2PortInfoEntry

swL2PortInfoEntry		1.3.6.1.4.1.171.11.133.5.1.2.3.1.1
A list of information for each port of the device.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2PortInfoEntry

swL2PortInfoPortIndex		1.3.6.1.4.1.171.11.133.5.1.2.3.1.1.1
This object indicates the module's port number.(1..Max port number in the module)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2PortInfoMediumType		1.3.6.1.4.1.171.11.133.5.1.2.3.1.1.2
Indicates the medium type of the port number.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	copper(1), fiber(2)

swL2PortInfoUnitID		1.3.6.1.4.1.171.11.133.5.1.2.3.1.1.3
Indicates the ID of the unit in the system.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2PortInfoType		1.3.6.1.4.1.171.11.133.5.1.2.3.1.1.4
This object indicates the connector type of this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	portType-100Base-TX(1), portType-100Base-FX(2), portType-100Base-FL(3), portType-1000Base-TX(4), portType-1000Base-SX(5), portType-1000Base-LX(6), portType-1000Base-SX-GBIC(7), portType-1000Base-LX-GBIC(8), portType-1000Base-TX-GBIC(9), portType-1000Base-1394(10), portType-1000Base-TX-GBIC-COMBO(11), portType-1000Base-none-GBIC(12), portType-1000Base-SX-MGBIC(13), portType-1000Base-LX-MGBIC(14), portType-1000Base-TX-MGBIC(15), portType-1000Base-none-MGBIC(16), portType-SIO(17), portType-10G(18), portType-10G-xenpak-1310nm(19), portType-10G-xenpak-850nm(20), portType-10G-xenpak-empty(21), portType-10G-xfp-1310nm(22), portType-10G-xfp-850nm(23), portType-10G-xfp-empty(24), portType-none(25)

swL2PortInfoLinkStatus		1.3.6.1.4.1.171.11.133.5.1.2.3.1.1.5
This object indicates the port link status.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), link-pass(2), link-fail(3)

swL2PortInfoNwayStatus		1.3.6.1.4.1.171.11.133.5.1.2.3.1.1.6
This object indicates the port speed and duplex mode.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	link-down(0), full-10Mbps-8023x(1), full-10Mbps-none(2), half-10Mbps-backp(3), half-10Mbps-none(4), full-100Mbps-8023x(5), full-100Mbps-none(6), half-100Mbps-backp(7), half-100Mbps-none(8), full-1Gigabps-8023x(9), full-1Gigabps-none(10), half-1Gigabps-backp(11), half-1Gigabps-none(12), full-10Gigabps-8023x(13), full-10Gigabps-none(14), half-10Gigabps-8023x(15), half-10Gigabps-none(16), empty(17), err-disabled(18)

swL2PortInfoModuleType		1.3.6.1.4.1.171.11.133.5.1.2.3.1.1.7
This object indicates the module type of this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), moduleType-COMBO(1), moduleType-1394(2), moduleType-1000T(3), moduleType-MGBIC(4), moduleType-1P-SC-SX(5), moduleType-2P-SC-SX(6), moduleType-1P-SC-LX(7), moduleType-2P-SC-LX(8), moduleType-1P-TX(9), moduleType-2P-TX(10), moduleType-1P-MTRJ-SX(11), moduleType-2P-MTRJ-SX(12), moduleType-1P-MTRJ-LX(13), moduleType-2P-MTRJ-LX(14), moduleType-1P-GBIC(15), moduleType-2P-GBIC(16), moduleType-1P-GBIC-1P-TX(17), moduleType-1P-GBIC-1P-STACK(18), moduleType-2P-STACK(19), moduleType-2P-100FX(20), moduleType-1P-100FX(21), moduleType-2P-100FX-NEW(22), moduleType-1P-100FL(23), moduleType-2P-100FL(24), moduleType-2P-100TX(25), moduleType-BaseModule-24PORT(26)

swL2PortInfoErrorDisabled		1.3.6.1.4.1.171.11.133.5.1.2.3.1.1.8
This object indicates the blocking type of this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), storm-control(1), stp-lbd(2), unknow(3), ctp-lbd(4), ddm(5), bpdu-protection(6), power-saving(7), port-security(8), ip-mac-port-binding(9), mac-temperature(10), oam-unidirectional-link(11)

swL2PortCtrlTable		1.3.6.1.4.1.171.11.133.5.1.2.3.2
A table that contains control information about every port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2PortCtrlEntry

swL2PortCtrlEntry		1.3.6.1.4.1.171.11.133.5.1.2.3.2.1
A list of control information for each port on the device.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2PortCtrlEntry

swL2PortCtrlPortIndex		1.3.6.1.4.1.171.11.133.5.1.2.3.2.1.1
This object indicates the module's port number.(1..Max port number in the module)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2PortCtrlMediumType		1.3.6.1.4.1.171.11.133.5.1.2.3.2.1.2
Indicates the medium type of the port number.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	copper(1), fiber(2)

swL2PortCtrlUnitIndex		1.3.6.1.4.1.171.11.133.5.1.2.3.2.1.3
Indicates the ID of the unit in the device
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2PortCtrlAdminState		1.3.6.1.4.1.171.11.133.5.1.2.3.2.1.4
This object decides if the port is enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL2PortCtrlNwayState		1.3.6.1.4.1.171.11.133.5.1.2.3.2.1.5
Chose the port speed, duplex mode, and N-Way function mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), nway-enabled(2), nway-disabled-10Mbps-Half(3), nway-disabled-10Mbps-Full(4), nway-disabled-100Mbps-Half(5), nway-disabled-100Mbps-Full(6), nway-disabled-1Gigabps-Half(7), nway-disabled-1Gigabps-Full(8), nway-disabled-1Gigabps-Full-master(9), nway-disabled-1Gigabps-Full-slave(10)

swL2PortCtrlFlowCtrlState		1.3.6.1.4.1.171.11.133.5.1.2.3.2.1.6
The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, the IEEE 802.3x flow control function sends PAUSE frames and receives PAUSE frames.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL2PortCtrlLearningState		1.3.6.1.4.1.171.11.133.5.1.2.3.2.1.7
This object decides if the port is locked or not.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL2PortCtrlMACNotifyState		1.3.6.1.4.1.171.11.133.5.1.2.3.2.1.8
This object sets each port's MAC notification state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL2PortCtrlMDIXState		1.3.6.1.4.1.171.11.133.5.1.2.3.2.1.10
This object configures the MDIX setting of the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	auto(1), normal(2), cross(3)

swL2PortCtrlAutoNegRestart		1.3.6.1.4.1.171.11.133.5.1.2.3.2.1.11
If the value of this object is set to restart(1) then this will force auto-negotiation to begin link renegotiation. If auto-negotiation signaling is disabled, a write to this object has no effect. Setting the value of this object to norestart(2) has no effect.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	restart(1), norestart(2)

swL2PortCtrlAutoNegCapAdvertisedBits		1.3.6.1.4.1.171.11.133.5.1.2.3.2.1.12
A value that uniquely identifies the set of capabilities advertised by the local auto-negotiation entity. Capabilities in this object that are not available in swL2PortAutoNegInfoCapabilityBits cannot be enabled. Note that the local auto-negotiation entity may advertise some capabilities beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for standard capabilities that are listed in the IANAifMauAutoNegCapBits TC.
Status: current	Access: read-write
OBJECT-TYPE
	IANAifMauAutoNegCapBits

swL2PortCtrlJumboFrame		1.3.6.1.4.1.171.11.133.5.1.2.3.3
This object configures the switch's jumbo frame settings.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL2PortCtrlJumboFrameMaxSize		1.3.6.1.4.1.171.11.133.5.1.2.3.4
This object describes how many bytes the max jumbo frame is.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

swL2PortCableDiagnosisTable		1.3.6.1.4.1.171.11.133.5.1.2.3.5
A table that contains cable diagnostic information about every port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2PortCableDiagnosisEntry

swL2PortCableDiagnosisEntry		1.3.6.1.4.1.171.11.133.5.1.2.3.5.1
A list with cable diagnostic information for each port of the device.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2PortCableDiagnosisEntry

swL2PortCableDiagnosisPortIndex		1.3.6.1.4.1.171.11.133.5.1.2.3.5.1.1
This object indicates the module's port number.(1..Max port number in the module)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2PortCableDiagnosisPairIndex		1.3.6.1.4.1.171.11.133.5.1.2.3.5.1.2
Indicates the pair index of each port. Pair 1 means pin 3 and 6 of the connector. Pair 2 means pin 1 and 2 of the connector. Pair 3 means pin 7 and 8 of the connector. Pair 4 means pin 4 and 5 of the connector.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4

swL2PortCableDiagnosisCableStatus		1.3.6.1.4.1.171.11.133.5.1.2.3.5.1.3
This object indicates the cable status.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ok(0), open(1), short(2), open-short(3), not-support(4), unknown(5)

swL2PortCableDiagnosisPairStatus		1.3.6.1.4.1.171.11.133.5.1.2.3.5.1.4
This object indicates the status of the pair.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	ok(0), open(1), short(2), fail(3), not-supported(4), unknown(5)

swL2PortCableDiagnosisPairLength		1.3.6.1.4.1.171.11.133.5.1.2.3.5.1.5
This object indicates the approx. length or length to failure of the pair. The unit value is in meters.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

swL2PortCableDiagnosisPairLengthInaccuracy		1.3.6.1.4.1.171.11.133.5.1.2.3.5.1.6
This object indicates the inaccuracy of a pair length. The unit value is in meters.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

swL2PortCounterCtrlTable		1.3.6.1.4.1.171.11.133.5.1.2.3.6
A table that is used to clear counter information about every port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2PortCounterCtrlEntry

swL2PortCounterCtrlEntry		1.3.6.1.4.1.171.11.133.5.1.2.3.6.1
A list of entries used to clear the counter information for each port of the device.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2PortCounterCtrlEntry

swL2PortCounterCtrlPortIndex		1.3.6.1.4.1.171.11.133.5.1.2.3.6.1.1
This object indicates the module's port number.(1..Max port number in the module)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2PortCounterClearCtrl		1.3.6.1.4.1.171.11.133.5.1.2.3.6.1.2
This object indicates whether to clear the counters for each port of the device or not.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), start(2)

swL2PortErrTable		1.3.6.1.4.1.171.11.133.5.1.2.3.7
A table that contains error information for each port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2PortErrEntry

swL2PortErrEntry		1.3.6.1.4.1.171.11.133.5.1.2.3.7.1
A list of information regarding port errors on the device.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2PortErrEntry

swL2PortErrPortIndex		1.3.6.1.4.1.171.11.133.5.1.2.3.7.1.1
This object indicates the module's port number.(1..Max port number in the module).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2PortErrPortState		1.3.6.1.4.1.171.11.133.5.1.2.3.7.1.2
This object indicates if the port state is enabled or disabled.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL2PortErrPortConnStatus		1.3.6.1.4.1.171.11.133.5.1.2.3.7.1.3
This object indicates whether the Port Status is err-disabled or not.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	other(1), err-disabled(2)

swL2PortErrPortReason		1.3.6.1.4.1.171.11.133.5.1.2.3.7.1.4
This object describes the reason for the port error.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), stp-lbd(1), storm-control(2), ctp-lbd(4), ddm(5), bpdu-protection(6), power-saving(7), port-security(8), ip-mac-port-binding(9), mac-temperature(10), oam-unidirectional-link(11)

swL2PortAutoNegInfoTable		1.3.6.1.4.1.171.11.133.5.1.2.3.8
A table that contains information about every port's auto negotiation status.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2PortAutoNegInfoEntry

swL2PortAutoNegInfoEntry		1.3.6.1.4.1.171.11.133.5.1.2.3.8.1
A list of information for each port auto negotiation of the device.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2PortAutoNegInfoEntry

swL2PortAutoNegInfoPortIndex		1.3.6.1.4.1.171.11.133.5.1.2.3.8.1.1
This object indicates the module's port number.(1..Max port number in the module)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2PortAutoNegInfoAdminStatus		1.3.6.1.4.1.171.11.133.5.1.2.3.8.1.2
If the value of this object is disabled(2) then the interface will act as it would if it had no auto-negotiation signaling. The status is affect by setting swL2PortCtrlNwayState.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL2PortAutoNegInfoCapabilityBits		1.3.6.1.4.1.171.11.133.5.1.2.3.8.1.3
A value that uniquely identifies the set of capabilities of the local auto-negotiation entity. Note that interfaces that support this MIB may have capabilities that extend beyond the scope of this MIB. Note that the local auto-negotiation entity may support some capabilities beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for standard capabilities that are listed in the IANAifMauAutoNegCapBits TC.
Status: current	Access: read-only
OBJECT-TYPE
	IANAifMauAutoNegCapBits

swL2PortAutoNegInfoCapAdvertisedBits		1.3.6.1.4.1.171.11.133.5.1.2.3.8.1.4
A value that uniquely identifies the set of capabilities advertised by the local auto-negotiation entity. Capabilities in this object that are not available in swL2PortAutoNegCapabilityBits cannot be enabled. Note that the local auto-negotiation entity may advertise some capabilities beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for standard capabilities that are listed in the IANAifMauAutoNegCapBits TC.
Status: current	Access: read-only
OBJECT-TYPE
	IANAifMauAutoNegCapBits

swL2PortAutoNegInfoCapReceivedBits		1.3.6.1.4.1.171.11.133.5.1.2.3.8.1.5
A value that uniquely identifies the set of capabilities received from the remote auto-negotiation entity. Note that interfaces that support this MIB may be attached to remote auto-negotiation entities that have capabilities beyond the scope of this MIB. This is indicated by returning the bit value bOther in addition to any bit values for standard capabilities that are listed in the IANAifMauAutoNegCapBits TC.
Status: current	Access: read-only
OBJECT-TYPE
	IANAifMauAutoNegCapBits

swL2PortDropCounterTable		1.3.6.1.4.1.171.11.133.5.1.2.3.9
A table that contains received error statistic information for each port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2PortDropCounterEntry

swL2PortDropCounterEntry		1.3.6.1.4.1.171.11.133.5.1.2.3.9.1
A list of information for each port received drop counter.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2PortDropCounterEntry

swL2PortDropCounterPortIndex		1.3.6.1.4.1.171.11.133.5.1.2.3.9.1.1
This object indicates the module's port number.(1..Max port number in the module)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2PortBufferFullDrops		1.3.6.1.4.1.171.11.133.5.1.2.3.9.1.2
The total number of packets discarded while input buffer full.
Status: current	Access: read-only
OBJECT-TYPE
	Counter

swL2PortACLDrops		1.3.6.1.4.1.171.11.133.5.1.2.3.9.1.3
The total number of received packets denied by ACLs.
Status: current	Access: read-only
OBJECT-TYPE
	Counter

swL2PortMulticastDrops		1.3.6.1.4.1.171.11.133.5.1.2.3.9.1.4
The total number of received multicast packet that is discarded.
Status: current	Access: read-only
OBJECT-TYPE
	Counter

swL2PortVLANIngressDrops		1.3.6.1.4.1.171.11.133.5.1.2.3.9.1.5
The total number of packets discarded by VLAN ingress checking.
Status: current	Access: read-only
OBJECT-TYPE
	Counter

swL2PortIngressBandwidthControlDrops		1.3.6.1.4.1.171.11.133.5.1.2.3.9.1.6
The total number of packets discarded by port ingress bandwidth control.
Status: current	Access: read-only
OBJECT-TYPE
	Counter

swL2PortInvalidIPv6Drops		1.3.6.1.4.1.171.11.133.5.1.2.3.9.1.7
The total number of packets discarded by IPv6 L3
Status: current	Access: read-only
OBJECT-TYPE
	Counter

swL2PortSTPDrops		1.3.6.1.4.1.171.11.133.5.1.2.3.9.1.8
The total number of packets discarded when ingress port is not in forwarding state.
Status: current	Access: read-only
OBJECT-TYPE
	Counter

swL2PortStormAndFDBDiscard		1.3.6.1.4.1.171.11.133.5.1.2.3.9.1.9
The total number of packets discarded by receiving policy (i.e. DST_DISCARD, SRC_DISCARD,RATE_CONTROL, etc.)
Status: current	Access: read-only
OBJECT-TYPE
	Counter

swL2PortMTUDrops		1.3.6.1.4.1.171.11.133.5.1.2.3.9.1.10
The total number of packets discarded by frames received, which exceeds Maximum Frame in length and contains a valid or invalid FCS.
Status: current	Access: read-only
OBJECT-TYPE
	Counter

swL2PortInvalidDestinationPort		1.3.6.1.4.1.171.11.133.5.1.2.3.9.1.11
The total number of packets dropped due to port bitmap of zero condition.
Status: current	Access: read-only
OBJECT-TYPE
	Counter

swL2PortJumboFrameCtrlTable		1.3.6.1.4.1.171.11.133.5.1.2.3.10
A table that contains information for each port's jumbo frame information.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2PortJumboFrameCtrlEntry

swL2PortJumboFrameCtrlEntry		1.3.6.1.4.1.171.11.133.5.1.2.3.10.1
A list of information for each port's jumbo frame of the device.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2PortJumboFrameCtrlEntry

swL2PortJumboFrameCtrlPortIndex		1.3.6.1.4.1.171.11.133.5.1.2.3.10.1.1
This object indicates the module's port number.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

swL2PortJumboFrameCtrlState		1.3.6.1.4.1.171.11.133.5.1.2.3.10.1.2
This object indicates the jumbo frame state on a specified port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL2PortSfpInfoTable		1.3.6.1.4.1.171.11.133.5.1.2.3.11
A table that contains information for each sfp pluged in port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2PortSfpInfoEntry

swL2PortSfpInfoEntry		1.3.6.1.4.1.171.11.133.5.1.2.3.11.1
A list of information for each sfp pluged in port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2PortSfpInfoEntry

swL2PortSfpInfoPortIndex		1.3.6.1.4.1.171.11.133.5.1.2.3.11.1.1
This object indicates the module's port number.(1..Max port number in the module)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2PortSfpInfoConnectType		1.3.6.1.4.1.171.11.133.5.1.2.3.11.1.2
The ConnectType of sfp informaiton.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..10)

swL2PortSfpInfoVendorName		1.3.6.1.4.1.171.11.133.5.1.2.3.11.1.3
The vendor name of sfp informaiton.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..16)

swL2PortSfpInfoVendorPN		1.3.6.1.4.1.171.11.133.5.1.2.3.11.1.4
The vendor PN of sfp informaiton.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..16)

swL2PortSfpInfoVendorSN		1.3.6.1.4.1.171.11.133.5.1.2.3.11.1.5
The vendor SN of sfp informaiton.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..16)

swL2PortSfpInfoVendorOUI		1.3.6.1.4.1.171.11.133.5.1.2.3.11.1.6
The vendor OUI of sfp information.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..6)

swL2PortSfpInfoVendorRev		1.3.6.1.4.1.171.11.133.5.1.2.3.11.1.7
The vendor Rev of sfp information.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..4)

swL2PortSfpInfoDateCode		1.3.6.1.4.1.171.11.133.5.1.2.3.11.1.8
The date code of sfp information.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..8)

swL2PortSfpInfoFiberType		1.3.6.1.4.1.171.11.133.5.1.2.3.11.1.9
The fiber type of sfp information.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(1..25)

swL2PortSfpInfoBaudRate		1.3.6.1.4.1.171.11.133.5.1.2.3.11.1.10
The baud rate of sfp information.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2PortSfpInfoWavelength		1.3.6.1.4.1.171.11.133.5.1.2.3.11.1.11
The wavelength of sfp information.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2PortLinkTimeTable		1.3.6.1.4.1.171.11.133.5.1.2.3.14
A table of information for the link time of the port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2PortLinkTimeEntry

swL2PortLinkTimeEntry		1.3.6.1.4.1.171.11.133.5.1.2.3.14.1
An entry in swL2PortLinkTimeTable contains the link time of the port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2PortLinkTimeEntry

swL2PortLinkTimeIfIndex		1.3.6.1.4.1.171.11.133.5.1.2.3.14.1.1
This object indicates the module's port number.(1..Max port number in the module)
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2PortLinkTimer		1.3.6.1.4.1.171.11.133.5.1.2.3.14.1.2
The link timer of the port after the port is link up When the value is 0 means the port is link down.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

swL2TrunkMaxSupportedEntries		1.3.6.1.4.1.171.11.133.5.1.2.9.1
Maximum number of entries in the trunk configuration table (swL2TrunkCtrlTable).
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2TrunkCurrentNumEntries		1.3.6.1.4.1.171.11.133.5.1.2.9.2
Current active number of entries in the trunk configuration table.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2TrunkCtrlTable		1.3.6.1.4.1.171.11.133.5.1.2.9.3
This table specifies information about the logical port trunk groups.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2TrunkCtrlEntry

swL2TrunkCtrlEntry		1.3.6.1.4.1.171.11.133.5.1.2.9.3.1
A list of information about each logical port trunk group.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2TrunkCtrlEntry

swL2TrunkIndex		1.3.6.1.4.1.171.11.133.5.1.2.9.3.1.1
The index number of the logical port trunk group. The trunk group number depends on the existence of unit and module.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2TrunkName		1.3.6.1.4.1.171.11.133.5.1.2.9.3.1.2
The name of the logical port trunk group.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString	Size(0..12)

swL2TrunkMasterPort		1.3.6.1.4.1.171.11.133.5.1.2.9.3.1.3
This object indicates the master port number of the port trunk entry. When using Port Trunking, you cannot configure the other ports of the group except the master port. Their configuration must be the same as the master port (e.g. speed, duplex, enabled/disabled, flow control, and so on).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	1..65535

swL2TrunkMember		1.3.6.1.4.1.171.11.133.5.1.2.9.3.1.4
Indicates the number of ports included in this Trunk group. The trunk port number depends on the existence of the module. The maximum number of ports is 8 for one trunk group.
Status: current	Access: read-create
OBJECT-TYPE
	PortList

swL2TrunkFloodingPort		1.3.6.1.4.1.171.11.133.5.1.2.9.3.1.5
The object indicates the flooding port number of the port trunk entry. The first port of the Trunk group is implicitly configured to be the flooding port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

swL2TrunkType		1.3.6.1.4.1.171.11.133.5.1.2.9.3.1.6
This object indicates the type of trunk group. static: is a static trunk group lacp: is a LACP trunk group.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	other(1), static(2), lacp(3)

swL2TrunkState		1.3.6.1.4.1.171.11.133.5.1.2.9.3.1.7
This object indicates the status of this entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

swL2TrunkAlgorithm		1.3.6.1.4.1.171.11.133.5.1.2.9.4
This object configures part of the packet examined by the switch when selecting the egress port for transmitting load-sharing data.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), mac-source(2), mac-destination(3), mac-source-dest(4), ip-source(5), ip-destination(6), ip-source-dest(7), l4-source-port(8), l4-destination-port(9), l4-source-dest-port(10)

swL2TrunkLACPPortTable		1.3.6.1.4.1.171.11.133.5.1.2.9.5
This table specifies which ports are grouped together (this can be up to 8 ports) into a single logical link.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2TrunkLACPPortEntry

swL2TrunkLACPPortEntry		1.3.6.1.4.1.171.11.133.5.1.2.9.5.1
A list of information specifying which ports are grouped together (this can be up to 8 ports) into a single logical link.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2TrunkLACPPortEntry

swL2TrunkLACPPortIndex		1.3.6.1.4.1.171.11.133.5.1.2.9.5.1.1
The index of logical port LACP.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2TrunkLACPPortState		1.3.6.1.4.1.171.11.133.5.1.2.9.5.1.2
The state of a logical port LACP.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), passive(2)

swL2TrunkVLANTable		1.3.6.1.4.1.171.11.133.5.1.2.9.6
This table is used to manage the VLAN trunking feature of the device.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2TrunkVLANEntry

swL2TrunkVLANEntry		1.3.6.1.4.1.171.11.133.5.1.2.9.6.1
This object is used to configure the VLAN trunking settings for each port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2TrunkVLANEntry

swL2TrunkVLANPort		1.3.6.1.4.1.171.11.133.5.1.2.9.6.1.1
This object indicates the port being configured.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2TrunkVLANState		1.3.6.1.4.1.171.11.133.5.1.2.9.6.1.2
The state of the logical port LACP.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL2MirrorLogicTargetPort		1.3.6.1.4.1.171.11.133.5.1.2.10.1
This object indicates which switch port will sniff another port. The port number is the sequential (logical) number, which is also applied to the bridge MIB, etc.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

swL2MirrorPortSourceIngress		1.3.6.1.4.1.171.11.133.5.1.2.10.2
This represents the port where ingress packets will be sniffed.
Status: current	Access: read-write
OBJECT-TYPE
	PortList

swL2MirrorPortSourceEgress		1.3.6.1.4.1.171.11.133.5.1.2.10.3
This represents the port where egress packets will be sniffed.
Status: current	Access: read-write
OBJECT-TYPE
	PortList

swL2MirrorPortState		1.3.6.1.4.1.171.11.133.5.1.2.10.4
This object indicates the port mirroring state. other (1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled (2) - After writing this value to the object, the corresponding entry will be removed from the table. enabled (3) - This entry resides in the table.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL2MirrorGroupTable		1.3.6.1.4.1.171.11.133.5.1.2.10.5
This table specifies information about the mirror group configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2MirrorGroupEntry

swL2MirrorGroupEntry		1.3.6.1.4.1.171.11.133.5.1.2.10.5.1
A list of information about each mirror group configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2MirrorGroupEntry

swL2MirrorGroupID		1.3.6.1.4.1.171.11.133.5.1.2.10.5.1.1
This object indicates the mirror group. The range of this object is (1..N), the value of N is project dependent.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER

swL2MirrorGroupRowStatus		1.3.6.1.4.1.171.11.133.5.1.2.10.5.1.2
This object indicates the status of this entry.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

swL2MirrorGroupState		1.3.6.1.4.1.171.11.133.5.1.2.10.5.1.3
This object indicates the mirror group state.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL2MirrorGroupTargetPort		1.3.6.1.4.1.171.11.133.5.1.2.10.5.1.4
This object indicates the mirror group target port.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	0..65535

swL2MirrorGroupSourceIngress		1.3.6.1.4.1.171.11.133.5.1.2.10.5.1.5
This object indicates the mirror group ingress source ports.
Status: current	Access: read-create
OBJECT-TYPE
	PortList

swL2MirrorGroupSourceEgress		1.3.6.1.4.1.171.11.133.5.1.2.10.5.1.6
This object indicates the mirror group egress source ports.
Status: current	Access: read-create
OBJECT-TYPE
	PortList

swL2IGMPAccessAuthTable		1.3.6.1.4.1.171.11.133.5.1.2.11.13
This table is used to manage the IGMP Access Authentication configurations of the device.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2IGMPAccessAuthEntry

swL2IGMPAccessAuthEntry		1.3.6.1.4.1.171.11.133.5.1.2.11.13.1
A list of manageable entities for IGMP Access Authentication. The configuration is done per port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2IGMPAccessAuthEntry

swL2IGMPAccessAuthPort		1.3.6.1.4.1.171.11.133.5.1.2.11.13.1.1
The index of the swL2IGMPAccessAuthTable. This object corresponds to the port being configured.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

swL2IGMPAccessAuthState		1.3.6.1.4.1.171.11.133.5.1.2.11.13.1.2
This object denotes the status of IGMP Access Authentication of the port. Note: enabled(1): Both the authentication and accounting functions are enabled, after the client is authenticated, the accounting message will be sent to Radius. disabled(2): Both the authentication and accounting functions are disabled. auth-only(3): Only the authentication function is enabled, after the client is authenticated, accounting message will not be sent to Radius. accounting-only(4): Only the accounting function is enabled, authentication is not needed, if the client joins a group, the accounting message will be sent to Radius.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2), auth-only(3), accounting-only(4)

swL2TrafficCtrlTable		1.3.6.1.4.1.171.11.133.5.1.2.13.1
This table specifies the storm traffic control configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2TrafficCtrlEntry

swL2TrafficCtrlEntry		1.3.6.1.4.1.171.11.133.5.1.2.13.1.1
A list of information specific to the storm traffic control configuration.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2TrafficCtrlEntry

swL2TrafficCtrlGroupIndex		1.3.6.1.4.1.171.11.133.5.1.2.13.1.1.1
The index of the logical port trunk. The trunk group number depends on the existence of a unit and module.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2TrafficCtrlUnitIndex		1.3.6.1.4.1.171.11.133.5.1.2.13.1.1.2
Indicates the ID of the unit in the device
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2TrafficCtrlBMStromthreshold		1.3.6.1.4.1.171.11.133.5.1.2.13.1.1.3
This object decides how many thousand broadcast/multicast packets per second (depending on swL2TrafficCtrlBcastStromCtrl, swL2TrafficCtrlMcastStromCtrl or swL2TrafficCtrlDlfStromCtrl objects being enabled) will activate the storm control function. Whenever a port reaches its configured amount of packets in the one second time interval, the device will start dropping that type of packet, until the time interval has expired. Once the time interval has expired, the device will restart forwarding that type of packet.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..255

swL2TrafficCtrlBcastStromCtrl		1.3.6.1.4.1.171.11.133.5.1.2.13.1.1.4
This object indicates if the broadcast storm control function is enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL2TrafficCtrlMcastStromCtrl		1.3.6.1.4.1.171.11.133.5.1.2.13.1.1.5
This object indicates if the multicast storm control function is enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL2TrafficCtrlDlfStromCtrl		1.3.6.1.4.1.171.11.133.5.1.2.13.1.1.6
This object indicates if the destination lookup fail function is enabled or disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), disabled(2), enabled(3)

swL2TrafficSegTable		1.3.6.1.4.1.171.11.133.5.1.2.14.1
This table specifies that the port can just forward traffic to the specific port list.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2TrafficSegEntry

swL2TrafficSegEntry		1.3.6.1.4.1.171.11.133.5.1.2.14.1.1
A list of information which specifies the port with its traffic forwarding list.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2TrafficSegEntry

swL2TrafficSegPort		1.3.6.1.4.1.171.11.133.5.1.2.14.1.1.1
The port number of the logical port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

swL2TrafficSegForwardPorts		1.3.6.1.4.1.171.11.133.5.1.2.14.1.1.2
The port list where a specific port can forward traffic.
Status: current	Access: read-write
OBJECT-TYPE
	PortList

swL2MulticastFilterModeVlanTable		1.3.6.1.4.1.171.11.133.5.1.2.17.1
A table that contains information about the VLAN multicast filter mode.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2MulticastFilterModeVlanEntry

swL2MulticastFilterModeVlanEntry		1.3.6.1.4.1.171.11.133.5.1.2.17.1.1
A list of multicast filter mode information for each VLAN.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2MulticastFilterModeVlanEntry

swL2MulticastFilterVid		1.3.6.1.4.1.171.11.133.5.1.2.17.1.1.1
Indicates the VID for each VLAN.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

swL2MulticastFilterVlanMode		1.3.6.1.4.1.171.11.133.5.1.2.17.1.1.2
Specifies the multicast filter mode for each VLAN.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	forward-all-groups(1), forward-unregistered-groups(2), filter-unregistered-groups(3)

swL2MulticastFilterModePortTable		1.3.6.1.4.1.171.11.133.5.1.2.17.2
A table that contains information about the port multicast filter mode.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2MulticastFilterModePortEntry

swL2MulticastFilterModePortEntry		1.3.6.1.4.1.171.11.133.5.1.2.17.2.1
A list of multicast filter mode information for each port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2MulticastFilterModePortEntry

swL2MulticastFilterPortIndex		1.3.6.1.4.1.171.11.133.5.1.2.17.2.1.1
Specifies the port number.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

swL2MulticastFilterPortMode		1.3.6.1.4.1.171.11.133.5.1.2.17.2.1.2
Specifies multicast filter mode for each port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	forward-all-groups(1), forward-unregistered-groups(2), filter-unregistered-groups(3)

swL2LoopDetectCtrl		1.3.6.1.4.1.171.11.133.5.1.2.18.1
OBJECT IDENTIFIER

swL2LoopDetectAdminState		1.3.6.1.4.1.171.11.133.5.1.2.18.1.1
This object indicates the loopback detection status for the system.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL2LoopDetectInterval		1.3.6.1.4.1.171.11.133.5.1.2.18.1.2
This object indicates the interval value, the range is from 1 to 32767 seconds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..32767

swL2LoopDetectRecoverTime		1.3.6.1.4.1.171.11.133.5.1.2.18.1.3
This object indicates the recover time, the range is from 60 to 1000000. The value of 0 disables the recover function.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..1000000

swL2LoopDetectMode		1.3.6.1.4.1.171.11.133.5.1.2.18.1.4
This object indicates the loopback detection mode for the system.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	vlan-based(1), port-based(2)

swL2LoopDetectTrapMode		1.3.6.1.4.1.171.11.133.5.1.2.18.1.5
This object indicates the loopback detection trap mode for the system.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), loop-detected(2), loop-cleared(3), both(4)

swL2LoopDetectPortMgmt		1.3.6.1.4.1.171.11.133.5.1.2.18.2
OBJECT IDENTIFIER

swL2LoopDetectPortTable		1.3.6.1.4.1.171.11.133.5.1.2.18.2.1
The table specifies the loopback detection function specified by port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SwL2LoopDetectPortEntry

swL2LoopDetectPortEntry		1.3.6.1.4.1.171.11.133.5.1.2.18.2.1.1
The table specifies the loopback detection function specified by port.
Status: current	Access: not-accessible
OBJECT-TYPE
	SwL2LoopDetectPortEntry

swL2LoopDetectPortIndex		1.3.6.1.4.1.171.11.133.5.1.2.18.2.1.1.1
This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

swL2LoopDetectPortState		1.3.6.1.4.1.171.11.133.5.1.2.18.2.1.1.2
This object indicates the loopback detection function state on the port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

swL2LoopDetectPortLoopVLAN		1.3.6.1.4.1.171.11.133.5.1.2.18.2.1.1.3
This object indicates the VLAN list that has detected a loopback.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

swL2LoopDetectPortLoopStatus		1.3.6.1.4.1.171.11.133.5.1.2.18.2.1.1.4
This object indicates the port status.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(1), loop(2), error(3), none(4)

swL2Notify		1.3.6.1.4.1.171.11.133.5.1.2.100.1
OBJECT IDENTIFIER

swL2NotifyMgmt		1.3.6.1.4.1.171.11.133.5.1.2.100.1.1
OBJECT IDENTIFIER

swL2NotifyPrefix		1.3.6.1.4.1.171.11.133.5.1.2.100.1.2
OBJECT IDENTIFIER

swL2NotifFirmware		1.3.6.1.4.1.171.11.133.5.1.2.100.1.2.0
OBJECT IDENTIFIER

swL2macNotificationSeverity		1.3.6.1.4.1.171.11.133.5.1.2.100.1.1.1
Indicates the level of macNotification detection.
Status: current	Access: read-write
OBJECT-TYPE
	AgentNotifyLevel

swL2PortSecurityViolationSeverity		1.3.6.1.4.1.171.11.133.5.1.2.100.1.1.2
Indicates the level of PortSecurityViolation detection.
Status: current	Access: read-write
OBJECT-TYPE
	AgentNotifyLevel

swL2macNotification		1.3.6.1.4.1.171.11.133.5.1.2.100.1.2.0.1
This trap indicates the MAC address variations in the address table .
Status: current	Access: read-write
NOTIFICATION-TYPE

swL2PortSecurityViolationTrap		1.3.6.1.4.1.171.11.133.5.1.2.100.1.2.0.2
When the port-security trap is enabled, new MAC addresses that violate the pre-defined port security configuration will trigger trap messages to be sent out.
Status: current	Access: read-write
NOTIFICATION-TYPE

swL2PortLoopOccurred		1.3.6.1.4.1.171.11.133.5.1.2.100.1.2.0.3
The trap is sent when a Port loop occurs.
Status: current	Access: read-write
NOTIFICATION-TYPE

swL2PortLoopRestart		1.3.6.1.4.1.171.11.133.5.1.2.100.1.2.0.4
The trap is sent when a Port loop restarts after the interval time.
Status: current	Access: read-write
NOTIFICATION-TYPE

swL2VlanLoopOccurred		1.3.6.1.4.1.171.11.133.5.1.2.100.1.2.0.5
The trap is sent when a Port with a VID loop occurs.
Status: current	Access: read-write
NOTIFICATION-TYPE

swL2VlanLoopRestart		1.3.6.1.4.1.171.11.133.5.1.2.100.1.2.0.6
The trap is sent when a Port with a VID loop restarts after the interval time.
Status: current	Access: read-write
NOTIFICATION-TYPE

swl2NotificationBidings		1.3.6.1.4.1.171.11.133.5.1.2.100.1.2.1
OBJECT IDENTIFIER

swL2macNotifyInfo		1.3.6.1.4.1.171.11.133.5.1.2.100.1.2.1.1
This object indicates the information for the device MAC address changes. And the detailed information include: Operation Code + MAC address + Box ID + Port Number + Zero... Operation Code: 1, 2 1 means learned a new MAC address 2 means deleted a old MAC address. Box ID: The switch box ID, for standalone device, it always 1. Port Number: The port number learned or deleted for the box. Zero: Used to separate each message(Operate Code + MAC address + Box ID + Port Number).
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..1024)

swL2PortSecurityViolationMac		1.3.6.1.4.1.171.11.133.5.1.2.100.1.2.1.2
This object indicates the MAC address that violated the port security configuration.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	MacAddress

swL2VlanLoopDetectVID		1.3.6.1.4.1.171.11.133.5.1.2.100.1.2.1.3
This object indicates the VID that detected a loopback.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	INTEGER