DESCH-PSC3-BASE-MIB
File:
DESCH-PSC3-BASE-MIB.mib (44578 bytes)
Imported modules
Imported symbols
Defined Types
| DcEventHistoryEntry |
|
| SEQUENCE |
|
|
|
| |
dcEventHistoryIndex |
Integer32 |
|
| |
dcEventHistoryTimestamp |
DisplayString |
|
| |
dcEventHistoryMessage |
DisplayString |
|
| DcAlarmEntry |
|
| SEQUENCE |
|
|
|
| |
dcAlarmIndex |
Integer32 |
|
| |
dcAlarmEventCategory |
INTEGER |
|
| |
dcAlarmEventName |
DisplayString |
|
| |
dcAlarmEventIdentifier |
Gauge32 |
|
| |
dcAlarmEventValue |
INTEGER |
|
| DcRectifierEntry |
|
| SEQUENCE |
|
|
|
| |
dcRectifierIndex |
Integer32 |
|
| |
dcRectifierIdentifier |
DisplayString |
|
| |
dcRectifierStatus |
INTEGER |
|
| DcGenericAlarmEntry |
|
| SEQUENCE |
|
|
|
| |
dcGenericAlarmIndex |
Integer32 |
|
| |
dcGenericAlarmEventName |
DisplayString |
|
| |
dcGenericAlarmEventIdentifier |
Gauge32 |
|
| |
dcGenericAlarmEventValue |
INTEGER |
|
| DcControlEventEntry |
|
| SEQUENCE |
|
|
|
| |
dcControlEventIndex |
Integer32 |
|
| |
dcControlEventName |
DisplayString |
|
| |
dcControlEventIdentifier |
Gauge32 |
|
| |
dcControlEventValue |
INTEGER |
|
| DcTrapDestinationEntry |
|
| SEQUENCE |
|
|
|
| |
dcTrapDestinationIndex |
Integer32 |
|
| |
dcTrapDestinationIp |
IpAddress |
|
| |
dcTrapDestinationPort |
Gauge32 |
|
Defined Values
| deschPsc3BaseMibModule |
1.3.6.1.4.1.20246.2.1.1.2 |
| MIB for managing a DC power system with PSC 3. |
| MODULE-IDENTITY |
|
|
|
| dcSystemInfo |
1.3.6.1.4.1.20246.2.3.1.1.1.2.1 |
| OBJECT IDENTIFIER |
|
|
|
| dcRectifier |
1.3.6.1.4.1.20246.2.3.1.1.1.2.4 |
| OBJECT IDENTIFIER |
|
|
|
| dcBattery |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5 |
| OBJECT IDENTIFIER |
|
|
|
| dcFloatCharge |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.1 |
| OBJECT IDENTIFIER |
|
|
|
| dcBatteryTest |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.2 |
| OBJECT IDENTIFIER |
|
|
|
| dcEqualize |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.4 |
| OBJECT IDENTIFIER |
|
|
|
| dcBoostCharge |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.5 |
| OBJECT IDENTIFIER |
|
|
|
| dcMisc |
1.3.6.1.4.1.20246.2.3.1.1.1.2.7 |
| OBJECT IDENTIFIER |
|
|
|
| dcSiteName |
1.3.6.1.4.1.20246.2.3.1.1.1.2.1.1 |
| An administratively-assigned site name for this
DC-power system. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(1..16) |
|
| dcSystemName |
1.3.6.1.4.1.20246.2.3.1.1.1.2.1.2 |
| An administratively-assigned system name for this
DC-power system. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(1..16) |
|
| dcSystemDateTime |
1.3.6.1.4.1.20246.2.3.1.1.1.2.1.3 |
| ISO 8601 representation of controller's local date/time.
The value is in the format YYYY-MM-DDThh:mm:ss.
An example of a valid string is: '2004-10-04T13:45:00'. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(19) |
|
| dcSoftwareVersion |
1.3.6.1.4.1.20246.2.3.1.1.1.2.1.4 |
| The controller's software version e.g V2.50Build1. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(1..25) |
|
| dcNumberUrgentAlarms |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.3 |
| Number of currently active urgent alarm sources. A zero
value indicates that urgent alarm is not active. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| dcNumberNonUrgentAlarms |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.4 |
| Number of currently active non urgent alarm sources. A zero
value indicates that non urgent alarm is not active. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| dcMainsFailureAlarm |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.5 |
| Mains failure alarm. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
inactive(1), active(2) |
|
| dcUrgentAlarmIdentifier |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.6 |
| Current unique urgent alarm event identifier. A zero value
indicates that urgent alarm is not active. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| dcUrgentAlarmValue |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.7 |
| Current urgent alarm event status that corresponds to the
urgent alarm identifier. If the urgent alarm identifier is zero
then the alarm value is false. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
false(1), indeterminate(2), true(3) |
|
| dcNonUrgentAlarmIdentifier |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.8 |
| Current unique non urgent alarm event identifier. A zero value
indicates that non urgent alarm is not active. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| dcNonUrgentAlarmValue |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.9 |
| Current non urgent alarm event status that corresponds to non urgent
alarm identifier. If the non urgent alarm identifier is zero then
the alarm value is false. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
false(1), indeterminate(2), true(3) |
|
| dcUrgentAlarmName |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.10 |
| Current alarm name for urgent alarm that corresponds to urgent
alarm identifier. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..255) |
|
| dcNonUrgentAlarmName |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.11 |
| Current alarm name for active non urgent alarm that corresponds
to non urgent alarm identifier. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..255) |
|
| dcSystemVoltage |
1.3.6.1.4.1.20246.2.3.1.1.1.2.3.1 |
| The measured system voltage. The max. value 2147483647
is used to indicate an invalid value. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| dcLoadCurrent |
1.3.6.1.4.1.20246.2.3.1.1.1.2.3.2 |
| The measured load current. The max. value 2147483647
is used to indicate an invalid value. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| dcBatteryCurrent |
1.3.6.1.4.1.20246.2.3.1.1.1.2.3.3 |
| The measured battery current. The max. value 2147483647
is used to indicate an invalid value. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| dcBatteryTemperature |
1.3.6.1.4.1.20246.2.3.1.1.1.2.3.4 |
| The measured battery temperature. The max. value 2147483647
is used to indicate an invalid value. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| dcChargeState |
1.3.6.1.4.1.20246.2.3.1.1.1.2.3.5 |
| Battery charge state. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
float(1), discharge(2), equalize(3), boost(4), battTest(5), recharge(6), sepCharge(7), evCtrlCharge(8) |
|
| dcCurrentLimit |
1.3.6.1.4.1.20246.2.3.1.1.1.2.3.6 |
| Battery current limit. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
inactive(1), active(2) |
|
| dcRectifierCurrent |
1.3.6.1.4.1.20246.2.3.1.1.1.2.3.7 |
| Total current of all working rectifier modules.
The maximum value 2147483647 is used to indicate
an invalid value. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| dcSystemPower |
1.3.6.1.4.1.20246.2.3.1.1.1.2.3.8 |
| Calculated system power. The maximum value
4294967295 is used to indicate an invalid value. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| dcNumberRectifiers |
1.3.6.1.4.1.20246.2.3.1.1.1.2.4.1 |
| The configured number of rectifiers plugged into
the system. The maximum number of rectifiers
is 128. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
0..128 |
|
| dcNumberRectifiersFailure |
1.3.6.1.4.1.20246.2.3.1.1.1.2.4.2 |
| Number of rectifiers that are not properly working. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
0..128 |
|
| dcNumberRectifiersOkay |
1.3.6.1.4.1.20246.2.3.1.1.1.2.4.3 |
| Number of rectifiers that are properly working. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
0..128 |
|
| dcUsys20 |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.1.1 |
| Voltage to regulate to at 20oC. If temperature
compensation is used, this voltage will vary. The
maximum value 2147483647 is used to indicate an invalid
value. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| dcTcoeff |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.1.2 |
| Temperature compensation coefficient for system voltage.
The maximum value 2147483647 is used to indicate
an invalid value. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| dcTcLow |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.1.3 |
| Low limit for the area in which the temperature compensation
is active. The maximum value 2147483647 is used to indicate
an invalid value. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| dcTcHigh |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.1.4 |
| High limit for the area in which the temperature compensation
is active. The maximum value 2147483647 is used to indicate
an invalid value. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| dcUsupport |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.2.1.1 |
| Support charge voltage for the battery. The maximum
value 2147483647 is used to indicate an invalid value. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| dcDuration |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.2.1.2 |
| Battery test duration. Zero indicates that this value
is not set. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| dcInterval |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.2.1.3 |
| Minimal time between programmed battery tests. Zero
indicates that this value is not set. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| dcDischargeCurrent |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.2.1.4 |
| Battery discharge current. The maximum value 2147483647
is used to indicate an invalid value. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| dcTestDateTime |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.2.2.1 |
| ISO 8601 representation of the last performed battery test.
The value is in the format YYYY-MM-DDThh:mm:ss. This parameter
is valid only if there is a test result available. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(19) |
|
| dcTestResult |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.2.2.2 |
| Result of last performed battery test. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
none(1), failed(2), aborted(3), loadFailure(4), okay(5) |
|
| dcTestEndVoltage |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.2.2.3 |
| System voltage at the end of the last performed battery test.
The maximum value 2147483647 is used to indicate an invalid
value. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| dcBatteryTestControl |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.2.3 |
| Start/stop of battery test. This special charge mode is used
to check the capacity of a battery.
Please not that a battery test can be started even if the battery
is not fully charged. In this case the test result is ambiguous
and the set failure event will become active. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
start(1), stop(2) |
|
| dcBatteryTestStatus |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.2.4 |
| Current status of battery test. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
inactive(1), starting(2), stopping(3), constantCurrent(4), timeBased(5), energyBased(6), recovery(7), realLoad(8), stop(9) |
|
| dcBatteryTestFailureEvent |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.2.5 |
| Reset battery test failure event. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
reset(1) |
|
| dcTotalBatteryCapacity |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.3.1 |
| Total battery capacity for all available batteries. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| dcEqualizeControl |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.4.1 |
| Start/stop of battery equalize which is a special charge
mode that applies a higher voltage to the batteries than
the float charge. This ensures that the cells are all
equally charged. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
start(1), stop(2) |
|
| dcEqualizeStatus |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.4.2 |
| Current status of battery equalize. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
inactive(1), starting(2), stopping(3), preparing(4), cooking(5), recovering(6) |
|
| dcBoostChargeControl |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.5.1 |
| Start/stop of boost charge which is a special charge mode
that applies a higher voltage to the batteries than the float
charge. This mode is started after a discharge phase to
recharge the batteries faster. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
start(1), stop(2) |
|
| dcBoostChargeStatus |
1.3.6.1.4.1.20246.2.3.1.1.1.2.5.5.2 |
| Current status of boost charge. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
inactive(1), starting(2), stopping(3), cooking(4), recovering(5) |
|
| dcFileProcessingStatus |
1.3.6.1.4.1.20246.2.3.1.1.1.2.7.2 |
| File processing status for software and setup up/downloads. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
idle(1), inProgress(2), successful(3), error(4), unknown(5) |
|
| dcSetupConfiguration |
1.3.6.1.4.1.20246.2.3.1.1.1.2.7.3 |
| Save current setup configuration to non-volatile memory. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
save(1) |
|
| dcEventHistoryTable |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.1 |
| Controller's event history table that shows the content of the
default log file. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
DcEventHistoryEntry |
|
| dcEventHistoryEntry |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.1.1 |
| A particular Event History entry. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
DcEventHistoryEntry |
|
|
| dcEventHistoryIndex |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.1.1.1 |
| Table index. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..10000 |
|
| dcEventHistoryTimestamp |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.1.1.2 |
| ISO8601 timestamp representation of a particular entry
in the form YYYY-MM-DDThh:mm:ss. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(19) |
|
| dcEventHistoryMessage |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.1.1.3 |
| Event message of a particular entry. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..255) |
|
| dcAlarmTable |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.2 |
| Table that shows all currently active alarm sources
causing urgent or non-urgent alarm(s). |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
DcAlarmEntry |
|
| dcAlarmEntry |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.2.1 |
| A particular active alarm source entry. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
DcAlarmEntry |
|
|
| dcAlarmIndex |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.2.1.1 |
| Table index. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..16 |
|
| dcAlarmEventCategory |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.2.1.2 |
| Specifies the type of alarm source. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
unknown(1), urgent(2), nonUrgent(3) |
|
| dcAlarmEventName |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.2.1.3 |
| Name of a particular alarm source entry. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..255) |
|
| dcAlarmEventIdentifier |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.2.1.4 |
| Unique alarm event identifier. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| dcAlarmEventValue |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.2.1.5 |
| Event status that corresponds to alarm event identifier. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
false(1), indeterminate(2), true(3) |
|
| dcRectifierTable |
1.3.6.1.4.1.20246.2.3.1.1.1.2.4.4 |
| Table that shows all currently active rectifier
modules. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
DcRectifierEntry |
|
| dcRectifierEntry |
1.3.6.1.4.1.20246.2.3.1.1.1.2.4.4.1 |
| A particular rectifier entry. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
DcRectifierEntry |
|
|
| dcRectifierIndex |
1.3.6.1.4.1.20246.2.3.1.1.1.2.4.4.1.1 |
| Table index. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
1..128 |
|
| dcRectifierIdentifier |
1.3.6.1.4.1.20246.2.3.1.1.1.2.4.4.1.2 |
| Unique rectifier identifier. If positioning active the
position number scheme is used otherwise the rectifier
instance is used to identify a rectifier. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..50) |
|
| dcRectifierStatus |
1.3.6.1.4.1.20246.2.3.1.1.1.2.4.4.1.3 |
| Specifies status of rectifiers. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
unknown(1), off(2), on(3) |
|
| dcGenericAlarmTable |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.12 |
| Table that shows ten alarm event assignments that can be
configured via WEB interface. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
DcGenericAlarmEntry |
|
| dcGenericAlarmEntry |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.12.1 |
| A particular generic alarm entry. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
DcGenericAlarmEntry |
|
|
| dcGenericAlarmEventName |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.12.1.2 |
| Plain text name of the assigned alarm event. Empty if not
configured. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..255) |
|
| dcGenericAlarmEventIdentifier |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.12.1.3 |
| Unique numeric identifier of the assigned alarm event. Zero
if not configured. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| dcGenericAlarmEventValue |
1.3.6.1.4.1.20246.2.3.1.1.1.2.2.12.1.4 |
| Current value of the assigned alarm event. Value is false if
not configured. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
false(1), true(2) |
|
| dcControlEventTable |
1.3.6.1.4.1.20246.2.3.1.1.1.2.6.1 |
| Table that shows ten output event assignments that can be
configured via WEB interface. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
DcControlEventEntry |
|
| dcControlEventEntry |
1.3.6.1.4.1.20246.2.3.1.1.1.2.6.1.1 |
| A particular generic output entry. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
DcControlEventEntry |
|
|
| dcControlEventName |
1.3.6.1.4.1.20246.2.3.1.1.1.2.6.1.1.2 |
| Plain text name of the assigned control event. Empty if not
configure. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DisplayString |
Size(0..255) |
|
| dcControlEventIdentifier |
1.3.6.1.4.1.20246.2.3.1.1.1.2.6.1.1.3 |
| Unique numeric identifier of the assigned control event. Zero
if not configured. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| dcControlEventValue |
1.3.6.1.4.1.20246.2.3.1.1.1.2.6.1.1.4 |
| Current value of the assigned control event. Value is false if
not configured. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
false(1), true(2) |
|
| dcTrapDestinationEntry |
1.3.6.1.4.1.20246.2.3.1.1.1.2.7.1.1 |
| A particular trap destination entry. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
DcTrapDestinationEntry |
|
|
| dcTrapDestinationIp |
1.3.6.1.4.1.20246.2.3.1.1.1.2.7.1.1.2 |
| IP address of the trap destination. Value is 0.0.0.0 if IP
address is not configured. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
IpAddress |
|
|
| dcTrapDestinationPort |
1.3.6.1.4.1.20246.2.3.1.1.1.2.7.1.1.3 |
| Port number of the trap destination. By default port 162
is used. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| systemNonUrgentAlarm |
1.3.6.1.4.1.20246.2.3.1.1.1.3.1.0.1 |
| The controller reports that one or more elements have changed
into none urgent alarm state. |
| Status: current |
Access: read-write |
| NOTIFICATION-TYPE |
|
|
|
| systemUrgentAlarm |
1.3.6.1.4.1.20246.2.3.1.1.1.3.1.0.2 |
| The controller reports that one or more elements have changed
into urgent alarm state. |
| Status: current |
Access: read-write |
| NOTIFICATION-TYPE |
|
|
|
| deschSystemInfoGroup |
1.3.6.1.4.1.20246.2.3.1.1.1.1.1.1 |
| The collection of system info scalar objects. |
| Status: current |
Access: read-write |
| OBJECT-GROUP |
|
|
|
| deschSystemAlarmGroup |
1.3.6.1.4.1.20246.2.3.1.1.1.1.1.2 |
| The collection of system alarm scalar objects. |
| Status: current |
Access: read-write |
| OBJECT-GROUP |
|
|
|
| deschSystemMonitorGroup |
1.3.6.1.4.1.20246.2.3.1.1.1.1.1.3 |
| The collection of system monitor scalar objects. |
| Status: current |
Access: read-write |
| OBJECT-GROUP |
|
|
|
| deschRectifiersGroup |
1.3.6.1.4.1.20246.2.3.1.1.1.1.1.4 |
| The collection of rectifier scalar objects. |
| Status: current |
Access: read-write |
| OBJECT-GROUP |
|
|
|
| deschEventHistoryTableGroup |
1.3.6.1.4.1.20246.2.3.1.1.1.1.1.5 |
| The collection of event history table objects. |
| Status: current |
Access: read-write |
| OBJECT-GROUP |
|
|
|
| deschAlarmTableGroup |
1.3.6.1.4.1.20246.2.3.1.1.1.1.1.6 |
| The collection of alarm table objects. |
| Status: current |
Access: read-write |
| OBJECT-GROUP |
|
|
|
| deschRectifierTableGroup |
1.3.6.1.4.1.20246.2.3.1.1.1.1.1.7 |
| The collection of rectifier table objects. |
| Status: current |
Access: read-write |
| OBJECT-GROUP |
|
|
|
| deschNotificationsGroup |
1.3.6.1.4.1.20246.2.3.1.1.1.1.1.8 |
| The group of all controller notifications. |
| Status: current |
Access: read-write |
| NOTIFICATION-GROUP |
|
|
|
| deschGenericAlarmTableGroup |
1.3.6.1.4.1.20246.2.3.1.1.1.1.1.9 |
| Assignment of events to alarm table entries. |
| Status: current |
Access: read-write |
| OBJECT-GROUP |
|
|
|
| deschBatteryGroup |
1.3.6.1.4.1.20246.2.3.1.1.1.1.1.10 |
| The collection of battery scalar objects. |
| Status: current |
Access: read-write |
| OBJECT-GROUP |
|
|
|
| deschControlEventTableGroup |
1.3.6.1.4.1.20246.2.3.1.1.1.1.1.11 |
| Assignment of control events to table entries. |
| Status: current |
Access: read-write |
| OBJECT-GROUP |
|
|
|
| deschMiscGroup |
1.3.6.1.4.1.20246.2.3.1.1.1.1.1.13 |
| The collection of miscellaneous objects. |
| Status: current |
Access: read-write |
| OBJECT-GROUP |
|
|
|
| deschControllerBasicCompl |
1.3.6.1.4.1.20246.2.3.1.1.1.1.2.1 |
| The basic implementation requirements for the controller MIB. |
| Status: current |
Access: read-write |
| MODULE-COMPLIANCE |
|
|
|