DELL-NETWORKING-DCB-MIB
File:
DELL-NETWORKING-DCB-MIB.mib (60259 bytes)
Imported modules
Imported symbols
Defined Types
| EnabledStatus |
|
| A simple status value for the object. |
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
enabled(1), disabled(2) |
|
| DcbAdminMode |
|
| 'on(1)', In this mode, the configurations,
either from this system or the remote system will take
effect based on DCBX negotiations.
'off(2)', In this mode, all the operational(local) parameters
for the feature will be same as Admin Configuration Parameters.
But Operational(local) parameters do not have any impact in the system. |
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
on(1), off(2) |
|
| DcbState |
|
| The state of the DCBX state machine.
off '(0)', In this state all Operational(local) parameters
for the feature will be same as Admin Configuration parameters
but will not be operational in the system(hardware).
init '(1)', In this state all Operational(local) parameters
for the feature will be same as Admin Configuration Parameters.
rxrecommended '(2)', In this state all the Operational(local)
parameters for the feature will be same as particular
feature Remote Parameters.
internallypropagated '(3)', In this state all the Operational(local)
parameters for the feature will be same as the internal propagated
information from the config source. |
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
off(0), init(1), rxrecommended(2), internallypropagated(3) |
|
| DcbStateMachineType |
|
| asymmetric'(1)',By using this state machine the operational parameters
for the DCB feature can be same as peer or not.
symmetric '(2)',By using this state machine the operational parameters
for the DCB feature will be same as peer.
feature '(3)' Feature State machine as used by legacy DCBX - CIN/CEE
versions. |
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
asymmetric(1), symmetric(2), feature(3) |
|
| DcbxPortRole |
|
| . |
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
manual(1), autoup(2), autodown(3), configSource(4) |
|
| DcbxVersion |
|
| . |
| TEXTUAL-CONVENTION |
|
|
|
| |
INTEGER |
auto(1), ieee(2), cin(3), cee(4) |
|
| DellNetDcbPortEntry |
|
| SEQUENCE |
|
|
|
| |
dellNetDcbPortNumber |
InterfaceIndex |
|
| |
dellNetDcbETSAdminStatus |
EnabledStatus |
|
| |
dellNetDcbPFCAdminStatus |
EnabledStatus |
|
| DellNetDCBXPortEntry |
|
| SEQUENCE |
|
|
|
| |
dellNetDCBXPortNumber |
InterfaceIndex |
|
| |
dellNetDCBXAdminStatus |
EnabledStatus |
|
| |
dellNetDCBXAutoCfgPortRole |
DcbxPortRole |
|
| |
dellNetDCBXPortVersion |
DcbxVersion |
|
| |
dellNetDCBXPortSupportedTLVs |
BITS |
|
| |
dellNetDCBXPortConfigTLVsTxEnable |
BITS |
|
| DellNetDCBXPortStatusEntry |
|
| SEQUENCE |
|
|
|
| |
dellNetDCBXPortOperVersion |
DcbxVersion |
|
| |
dellNetDCBXPortPeerMACaddress |
MacAddress |
|
| |
dellNetDCBXPortCfgSource |
INTEGER |
|
| |
dellNetDCBXOperStatus |
EnabledStatus |
|
| |
dellNetDCBXPortMultiplePeerCount |
Counter32 |
|
| |
dellNetDCBXPortPeerRemovedCount |
Counter32 |
|
| |
dellNetDCBXPortPeerOperVersionNum |
Unsigned32 |
|
| |
dellNetDCBXPortPeerMaxVersion |
Unsigned32 |
|
| |
dellNetDCBXPortSeqNum |
Unsigned32 |
|
| |
dellNetDCBXPortAckNum |
Unsigned32 |
|
| |
dellNetDCBXPortPeerRcvdAckNum |
Unsigned32 |
|
| |
dellNetDCBXPortTxCount |
Counter32 |
|
| |
dellNetDCBXPortRxCount |
Counter32 |
|
| |
dellNetDCBXPortErrorFramesCount |
Counter32 |
|
| DellNetETSPortEntry |
|
| SEQUENCE |
|
|
|
| |
dellNetETSPortNumber |
InterfaceIndex |
|
| |
dellNetETSAdminMode |
DcbAdminMode |
|
| |
dellNetETSDcbxOperState |
DcbState |
|
| |
dellNetETSDcbxStateMachine |
DcbStateMachineType |
|
| |
dellNetETSOperStatus |
EnabledStatus |
|
| |
dellNetETSClearTLVCounters |
TruthValue |
|
| |
dellNetETSConfTxTLVCounter |
Counter32 |
|
| |
dellNetETSConfRxTLVCounter |
Counter32 |
|
| |
dellNetETSConfRxTLVErrors |
Counter32 |
|
| |
dellNetETSRecoTxTLVCounter |
Counter32 |
|
| |
dellNetETSRecoRxTLVCounter |
Counter32 |
|
| |
dellNetETSRecoRxTLVErrors |
Counter32 |
|
| DellNetPFCPortEntry |
|
| SEQUENCE |
|
|
|
| |
dellNetPFCPortNumber |
InterfaceIndex |
|
| |
dellNetPFCAdminMode |
DcbAdminMode |
|
| |
dellNetPFCDcbxOperState |
DcbState |
|
| |
dellNetPFCDcbxStateMachine |
DcbStateMachineType |
|
| |
dellNetPFCOperStatus |
EnabledStatus |
|
| |
dellNetPFCClearTLVCounters |
TruthValue |
|
| |
dellNetPFCTxTLVCounter |
Counter32 |
|
| |
dellNetPFCRxTLVCounter |
Counter32 |
|
| |
dellNetPFCRxTLVErrors |
Counter32 |
|
Defined Values
| dellNetDcb |
1.3.6.1.4.1.6027.3.15 |
| The proprietary extension MIB module for Dell Networking OS DCB and DCBX. |
| MODULE-IDENTITY |
|
|
|
| dellNetDcbPfcMinThreshold |
1.3.6.1.4.1.6027.3.15.1.1 |
| The minimum PFC(Priority Based Flow Control) threshold for the switch.
This Object indicates the minimum Receive queue buffer count.
The minimum and maximum values for this object may vary based on the
underlying hardware's capacity. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
1..65535 |
|
| dellNetDcbPfcMaxThreshold |
1.3.6.1.4.1.6027.3.15.1.2 |
| The maximum PFC(Priority Based Flow Control)threshold for the switch.
This Object indicates the maximum Receive queue buffer count.
The minimum and maximum values for this object may vary based
on the underlying hardware's capacity. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
1..65535 |
|
| dellNetDcbMaxPfcProfiles |
1.3.6.1.4.1.6027.3.15.1.3 |
| The maximum number of PFC(Priority Based Flow Control)profiles supported
by the device.
A PFC profile is a bitmap, containing the status of PFC for all the
priorities.
If Bit 0 is set, then it means PFC is enabled for priority 0, otherwise
PFC is disabled for priority 0.
If Bit 1 is set, then it means PFC is enabled for priority 1, otherwise
PFC is disabled for priority 1, and so on.
If this object value is zero, it means all the bits are set to zero and
PFC is disabled for all priorities.
If this object's value is 3, it means the bits 0 and 1 are set and
PFC is enabled for priorities 0 and 1 and disabled for all other priorities.
Device supporting 256 PFC profiles, means all possible combination of
PFC status on 8 priorities are supported. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
1..256 |
|
| dellNetDcbPortTable |
1.3.6.1.4.1.6027.3.15.2.1 |
| Port table contains the DCB features
(Enhanced Transmission Selection/Priortiy Based Flow Control)
status (enabled or disabled). |
| Status: obsolete |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
DellNetDcbPortEntry |
|
| dellNetDcbPortEntry |
1.3.6.1.4.1.6027.3.15.2.1.1 |
| An entry containing DCB control parameters for a particular port. |
| Status: obsolete |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
DellNetDcbPortEntry |
|
|
| dellNetDcbPortNumber |
1.3.6.1.4.1.6027.3.15.2.1.1.1 |
| This indicates the interface identifier for which the Dcb
configuration is applied. |
| Status: obsolete |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InterfaceIndex |
|
|
| dellNetDcbETSAdminStatus |
1.3.6.1.4.1.6027.3.15.2.1.1.2 |
| This object is used to display if ETS feature is
enabled or disabled on the given port. |
| Status: obsolete |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| dellNetDcbPFCAdminStatus |
1.3.6.1.4.1.6027.3.15.2.1.1.3 |
| This object is used to display if PFC feature is
enabled or disabled on the given port. |
| Status: obsolete |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| dellNetDcbxGlobalTraceLevel |
1.3.6.1.4.1.6027.3.15.3.1.1.1 |
| This object is used to enable Trace Statements in DCBX Module.
A FOUR BYTE integer is used for enabling the level of tracing.
Each BIT in the four byte integer represents a particular
level of Trace.
The mapping between the bit positions & the level of trace is
as follows:
1 - Management Traces
2 - DCBX State Machine Traces
3 - TLV Traces
4 - System Resource Traces
5 - Failure Traces
6 - Configuration Exchange Traces
7 - Auto Detection Traces
The remaining bits are unused.
The user has to enter the corresponding INTEGER VALUE for the
trace to be set. Only one trace can be enabled at a time.
To enable all the traces, sum of all individual
traces must be provided. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| dellNetDCBXGlobalVersion |
1.3.6.1.4.1.6027.3.15.3.1.1.2 |
| CIN is Cisco Intel Nuova DCBX (version 1.0).
CEE is converged enhanced ethernet DCBX (version 1.06).
IEEE is 802-1 az version.
The default value is auto.
DCBX supports the legacy implementations v1.0 (CIN) and
v1.06 (CEE) in addition to standard IEEE version 2.4 DCBX.
1.DCBX starts in standard IEEE mode by sending an IEEE
standard version 2.4 DCBX frame. If the peer responds,
then IEEE standard version 2.4 DCBX is used,Starts means
after a link up, a DCBX timeout (or multiple peer
condition) or when commanded by the network operator.
If DCBX receives a DCBX frame with an OUI indicating a
legacy version, it immediately switches into legacy mode
for the detected version and does not wait for the
3x LLDP fast timeout.
2.If no IEEE DCBX response is received within 3 times the
LLDP fast transmit timeout period, DCBX immediately
transmits a version 1.06 DCBX frame with the
appropriate version number. If DCBX receives a DCBX
frame with an OUI indicating IEEE standard support,
it immediately switches into IEEE standard mode and
does not wait for the timer. If DCBX receives a DCBX
frame with an OUI indicating legacy mode and a version
number indicating version 1.0 support, it immediately
switches into legacy 1.0 mode and does not wait for the
timer.
3.If no version 1.06 response is received within 3 times
the DCBX fast transmit timeout period, DCBX falls back
to version 1.0 and immediately transmits a version 1.0
frame. If no response is received within 3 times the
DCBX fast transmit period, DCBX waits the standard LLDP
timeout period, and then begins again with step 1. If
DCBX receives a DCBX frame with an OUI indicating IEEE
standard mode, it immediately switches into IEEE
standard mode. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DcbxVersion |
|
|
| dellNetDCBXPortEntry |
1.3.6.1.4.1.6027.3.15.3.1.2.1 |
| An entry containing DCBX control parameters for a particular port. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
DellNetDCBXPortEntry |
|
|
| dellNetDCBXPortNumber |
1.3.6.1.4.1.6027.3.15.3.1.2.1.1 |
| This indicates the interface identifier for which the DCBX
configuration is applied. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InterfaceIndex |
|
|
| dellNetDCBXAdminStatus |
1.3.6.1.4.1.6027.3.15.3.1.2.1.2 |
| This object is used to display if DCBX feature is
enabled(1) or disabled(2) on the given port. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| dellNetDCBXAutoCfgPortRole |
1.3.6.1.4.1.6027.3.15.3.1.2.1.3 |
| Ports operating in the manual role do not have their
configuration affected by peer devices or by internal
propagation of configuration. These ports will advertise
their configuration to their peer if DCBX is enabled
on that port.
Auto-up: Advertises a configuration, but is also willing
to accept a configuration from the link-partner and
propagate it internally to the auto-downstream ports
as well as receive configuration propagated internally
by other auto-upstream ports.
Auto-down: Advertises a configuration but is not willing
to accept one from the link partner. However, the port
will accept a configuration propagated internally by the
configuration source.
Configuration Source:In this role, the port has been
manually selected to be the configuration source.
Configuration received over this port is propagated
to the other auto-configuration ports. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DcbxPortRole |
|
|
| dellNetDCBXPortVersion |
1.3.6.1.4.1.6027.3.15.3.1.2.1.4 |
| CIN is Cisco Intel Nuova DCBX (version 1.0).
CEE is converged enhanced ethernet DCBX (version 1.06).
IEEE is 802-1 az version.
The default value is auto.
DCBX supports the legacy implementations v1.0 (CIN) and
v1.06 (CEE) in addition to standard IEEE version 2.4 DCBX.
1.DCBX starts in standard IEEE mode by sending an IEEE
standard version 2.4 DCBX frame. If the peer responds,
then IEEE standard version 2.4 DCBX is used,Starts means
after a link up, a DCBX timeout (or multiple peer
condition) or when commanded by the network operator.
If DCBX receives a DCBX frame with an OUI indicating a
legacy version, it immediately switches into legacy mode
for the detected version and does not wait for the
3x LLDP fast timeout.
2.If no IEEE DCBX response is received within 3 times the
LLDP fast transmit timeout period, DCBX immediately
transmits a version 1.06 DCBX frame with the
appropriate version number. If DCBX receives a DCBX
frame with an OUI indicating IEEE standard support,
it immediately switches into IEEE standard mode and
does not wait for the timer. If DCBX receives a DCBX
frame with an OUI indicating legacy mode and a version
number indicating version 1.0 support, it immediately
switches into legacy 1.0 mode and does not wait for the
timer.
3.If no version 1.06 response is received within 3 times
the DCBX fast transmit timeout period, DCBX falls back
to version 1.0 and immediately transmits a version 1.0
frame. If no response is received within 3 times the
DCBX fast transmit period, DCBX waits the standard LLDP
timeout period, and then begins again with step 1. If
DCBX receives a DCBX frame with an OUI indicating IEEE
standard mode, it immediately switches into IEEE
standard mode. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
DcbxVersion |
|
|
| dellNetDCBXPortSupportedTLVs |
1.3.6.1.4.1.6027.3.15.3.1.2.1.5 |
| Bitmap that includes the supported set of DCBX LLDP
TLVs the device is capable of and whose transmission is allowed on
the local LLDP agent by network management.
Having the bit 'pfc(0)' set indicates that the LLDP
transmit PFC TLV as part of DCBX TLVs.
Having the bit 'etcConfig(1)' set indicates that the LLDP
transmit ETS configuration TLV as part of DCBX TLVs.
Having the bit 'etsRecom(2)' set indicates that
transmit ETS Recommendation TLV as part of DCBX TLVs.
Having the bit 'applicationPriorityFCOE(3)' set indicates that
the LLDP transmit applicationPriority TLV for FCOE as part of
DCBX TLVs.
Having the bit 'applicationPriorityISCSI(4)' set indicates that
the LLDP transmit applicationPriority TLV for ISCSI as part of
DCBX TLVs. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
BITS |
pfc(0), etsConfig(1), etsRecom(2), applicationPriorityFCOE(3), applicationPriorityISCSI(4) |
|
| dellNetDCBXPortConfigTLVsTxEnable |
1.3.6.1.4.1.6027.3.15.3.1.2.1.6 |
| Bitmap that includes the DCBX defined set of LLDP
TLVs whose transmission is enabled on the local LLDP agent by
network management.
Having the bit 'pfc(0)' set indicates that the LLDP
transmit PFC TLV as part of DCBX TLVs.
Having the bit 'etsConfig(1)' set indicates that the LLDP
transmit ETS configuration TLV as part of DCBX TLVs.
Having the bit 'etsRecom(2)' set indicates that
transmit ETS Recommendation TLV as part of DCBX TLVs.
Having the bit 'applicationPriorityFCOE(3)' set indicates that
the LLDP transmit applicationPriority TLV for FCOE as part of
DCBX TLVs.
Having the bit 'applicationPriorityISCSI(4)' set indicates that
the LLDP transmit applicationPriority TLV for ISCSI as part of
DCBX TLVs. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
BITS |
pfc(0), etsConfig(1), etsRecom(2), applicationPriorityFCOE(3), applicationPriorityISCSI(4) |
|
| dellNetDCBXPortStatusEntry |
1.3.6.1.4.1.6027.3.15.3.1.3.1 |
| . |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
DellNetDCBXPortStatusEntry |
|
|
| dellNetDCBXPortOperVersion |
1.3.6.1.4.1.6027.3.15.3.1.3.1.2 |
| Specifies the DCBX mode in which the interface is
currently operating. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DcbxVersion |
|
|
| dellNetDCBXPortCfgSource |
1.3.6.1.4.1.6027.3.15.3.1.3.1.4 |
| Indicates if this port is the source of configuration
information for auto-* ports. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
false(0), true(1) |
|
| dellNetDCBXOperStatus |
1.3.6.1.4.1.6027.3.15.3.1.3.1.5 |
| This object gives information on the operational status of
DCBX on the given port.
Enabled(1) indicates DCBX on the port is in sync with the
remote and is operationally up.
Disabled(2) indicates DCBX on the port is operationally
disabled. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| dellNetDCBXPortMultiplePeerCount |
1.3.6.1.4.1.6027.3.15.3.1.3.1.6 |
| Indicates number of times multiple peers were detected.
A duplicate peer is when more than one DCBX peer is
detected on a port. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| dellNetDCBXPortPeerOperVersionNum |
1.3.6.1.4.1.6027.3.15.3.1.3.1.8 |
| Specifies the operational version of the peer DCBX device.
Valid only when peer device is a CEE/CIN DCBX device. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| dellNetDCBXPortPeerMaxVersion |
1.3.6.1.4.1.6027.3.15.3.1.3.1.9 |
| Specifies the max version of the peer DCBX device.
Valid only when peer device is CEE/CIN DCBX device. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| dellNetDCBXPortSeqNum |
1.3.6.1.4.1.6027.3.15.3.1.3.1.10 |
| Specifies the current sequence number that is sent
in DCBX control TLVs in CEE/CIN Mode. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| dellNetDCBXPortAckNum |
1.3.6.1.4.1.6027.3.15.3.1.3.1.11 |
| Specifies the current ACK number that is to be sent
to peer in DCBX control TLVs in CEE/CIN Mode. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| dellNetDCBXPortPeerRcvdAckNum |
1.3.6.1.4.1.6027.3.15.3.1.3.1.12 |
| Specifies the current ACK number that is sent by peer
in DCBX control TLV in CEE/CIN Mode. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| dellNetDCBXPortTxCount |
1.3.6.1.4.1.6027.3.15.3.1.3.1.13 |
| The number of DCBX frames transmitted per interface. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| dellNetDCBXPortRxCount |
1.3.6.1.4.1.6027.3.15.3.1.3.1.14 |
| The number of DCBX frames received per interface. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| dellNetETSSystemControl |
1.3.6.1.4.1.6027.3.15.3.2.1.1 |
| The ETS(Enhanced Transmission selection) system control status
for the switch.
It indicates whether ETS Module in the system is
running or shutdown. When this object returns 'running',
resources required by ETS module are allocated and
the module is running. When this object returns 'shutdown',
all the pools used by ETS module are released to the system. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
running(1), shutdown(2) |
|
| dellNetETSModuleStatus |
1.3.6.1.4.1.6027.3.15.3.2.1.2 |
| The ETS(Enhanced Transmission Selection) Module status for the switch.
If this object returns with 'disabled', then all the ports
have the ETS feature disabled in the system(hardware)
and the DCBX state machine has stopped on the ports.
If this object returns with 'enabled', then all the ports
have the ETS feature enabled in the system(hardware)
and the DCBX state machine is running on the ports. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| dellNetETSClearCounters |
1.3.6.1.4.1.6027.3.15.3.2.1.3 |
| This object when set to TRUE, clears the following counters
for the ETS Module:
dellNetETSConfTxTLVCounter,
dellNetETSConfRxTLVCounter,
dellNetETSConfRxTLVErrors,
dellNetETSRecoTxTLVCounter,
dellNetETSRecoRxTLVCounter,
dellNetETSRecoRxTLVErrors.
Setting this object to FALSE has no effect.
This object always returns FALSE when read. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| dellNetETSGlobalEnableTrap |
1.3.6.1.4.1.6027.3.15.3.2.1.4 |
| This object indicates whether the transmission of TRAP
notification messages for ETS feature is enabled or disabled. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| dellNetETSPortTable |
1.3.6.1.4.1.6027.3.15.3.2.2 |
| ETS Port table contains the ETS (Enhanced Transmission Selection) features
information specific to this port.
An entry created in this table in the following tables in the standard
DCBX Mib for this port.
lldpXdot1dcbxConfigTCSupportedTable,
lldpXdot1dcbxConfigETSConfigurationTable,
lldpXdot1dcbxConfigETSRecommendationTable,
lldpXdot1dcbxLocTCSupportedTable,
lldpXdot1dcbxLocETSBasicConfigurationTable,
lldpXdot1dcbxLocETSConPriorityAssignmentTable,
lldpXdot1dcbxLocETSRecommendationTable,
lldpXdot1dcbxAdminTCSupportedTable,
lldpXdot1dcbxAdminETSBasicConfigurationTable,
lldpXdot1dcbxAdminETSConPriorityAssignmentTable,
lldpXdot1dcbxAdminETSRecommendationTable.
Deletion of entry in this table deletes all the entries in the above tables
in the standatd DCBX mib for this port. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
DellNetETSPortEntry |
|
| dellNetETSPortEntry |
1.3.6.1.4.1.6027.3.15.3.2.2.1 |
| An entry containing ETS control parameters and ETS information
for a particular port. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
DellNetETSPortEntry |
|
|
| dellNetETSPortNumber |
1.3.6.1.4.1.6027.3.15.3.2.2.1.1 |
| This indicates the interface identifier for which the ETS
configuration is applied. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InterfaceIndex |
|
|
| dellNetETSAdminMode |
1.3.6.1.4.1.6027.3.15.3.2.2.1.2 |
| This object is used to display the Admin mode for ETS feature on
the given port.
If the mode is 'on(1)',ETS feature is enabled on this port.
ETS configurations, either from this system or
the remote system will take effect based on DCBX negotiations.
If the mode is 'off(2)', ETS feature is disabled on this port.
Operational(local) parameters is same as Admin Configuration
Parameters. But Operational(local) parameters do not have any impact
in the system and dellNetETSOperState is in 'Off' state.
dellNetETSDcbxOperState becomes oper up if remote is also disabled.
The Operational(local) parameters do not have any impact in
the system if this object value is 'on(1)' and
dellNetETSModuleStatus is disabled. dellNetETSDcbxOperState will
be in 'Off' State. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DcbAdminMode |
|
|
| dellNetETSDcbxOperState |
1.3.6.1.4.1.6027.3.15.3.2.2.1.3 |
| This object is used to display the current state of the
DCBX state machine for the ETS feature on the given port.
If state is Off '(0)', then ETS Operational(local) parameters
will be same as ETS Admin Configuration Parameters and will
not have any impact in the system(hardware).
If state is init '(1)', then ETS Operational(local) parameters
will be same as ETS Admin Configuration Parameters.
If state is rxrecommended '(2)', then ETS Operational(local) parameters
will be same as ETS Remote Parameters.
internallypropagated '(3)', In this state all the Operational(local)
parameters for the feature will be same as the internal propagated
information from the config source. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DcbState |
|
|
| dellNetETSDcbxStateMachine |
1.3.6.1.4.1.6027.3.15.3.2.2.1.4 |
| This object is used to display the DCBX state machine
type that is used by the ETS feature on the given port. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DcbStateMachineType |
|
|
| dellNetETSOperStatus |
1.3.6.1.4.1.6027.3.15.3.2.2.1.5 |
| This object gives information on the operational status of ETS
on the given port.
Enabled(1) indicates ETS on the port is in sync with the remote
and is operationally up.
Disabled(2) indicates ETS on the port is operationally disabled. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| dellNetETSClearTLVCounters |
1.3.6.1.4.1.6027.3.15.3.2.2.1.6 |
| This object when set to TRUE, clears the following counters
associated with a Port:
dellNetETSConfTxTLVCounter,
dellNetETSConfRxTLVCounter,
dellNetETSConfRxTLVErrors,
dellNetETSRecoTxTLVCounter,
dellNetETSRecoRxTLVCounter,
dellNetETSRecoRxTLVErrors.
Setting this object to FALSE has no effect.
This object always returns FALSE when read. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| dellNetETSConfTxTLVCounter |
1.3.6.1.4.1.6027.3.15.3.2.2.1.7 |
| This object is used to keep track of the number of ETS
configuration TLV that are transmitted from this port.
This counter will be incremented every time when there
is ETS Configuration TLV is generated and transmitted
to the LLDP. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| dellNetETSConfRxTLVCounter |
1.3.6.1.4.1.6027.3.15.3.2.2.1.8 |
| This object is used to keep track of the number of ETS
ConfigurationTLV that are received in this port. This
counter will be incremented every time when there is ETS
Configuration TLV is received from the LLDP. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| dellNetETSConfRxTLVErrors |
1.3.6.1.4.1.6027.3.15.3.2.2.1.9 |
| This object is used to keep track of number of malformed
ETS Conf TLVs received by ETS. This counter will be
incremented every time a ETS Conf TLV is dropped by ETS. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| dellNetETSRecoTxTLVCounter |
1.3.6.1.4.1.6027.3.15.3.2.2.1.10 |
| This object is used to keep track of the number of ETS
Recommendation TLV that are transmitted from this port.
This counter will be incremented every time when there
is ETS Recommendation TLV is generated and transmitted
to the LLDP. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| dellNetETSRecoRxTLVCounter |
1.3.6.1.4.1.6027.3.15.3.2.2.1.11 |
| This object is used to keep track of the number of ETS
Recommendation TLV that are received in this port. This
counter will be incremented every time when there is ETS
Recommendation TLV is received from the LLDP. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| dellNetETSRecoRxTLVErrors |
1.3.6.1.4.1.6027.3.15.3.2.2.1.12 |
| This object is used to keep track of number of malformed
ETS Reco TLVs received by ETS. This counter will be
incremented every time a ETS Reco TLV is dropped by ETS. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| dellNetPFCSystemControl |
1.3.6.1.4.1.6027.3.15.3.3.1.1 |
| The PFC(Priority Based Flow Control) system control status for the switch.
It indicates whether PFC Module in the system is
running or shutdown. When this object returns 'running',
resources required by PFC module are allocated and
the module is running. When this object returns 'shutdown',
all the pools used by PFC module are released to the system. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
running(1), shutdown(2) |
|
| dellNetPFCModuleStatus |
1.3.6.1.4.1.6027.3.15.3.3.1.2 |
| The PFC(Priority Based Flow Control) Module status for the switch.
If this object returns with 'disabled', then all the ports
have the PFC feature disabled in the system(hardware)
and the DCBX state machine has stopped on the ports.
If this object returns with 'enabled', then all the ports
have the PFC feature enabled in the system(hardware)
and the DCBX state machine is running on the ports. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| dellNetPFCClearCounters |
1.3.6.1.4.1.6027.3.15.3.3.1.3 |
| This object when set to TRUE, clears the following counters
for the PFC Module:
dellNetPFCTxTLVCounter,
dellNetPFCRxTLVCounter,
dellNetPFCRxTLVErrors.
Setting this object to FALSE has no effect.
This object always returns FALSE when read. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| dellNetPFCGlobalEnableTrap |
1.3.6.1.4.1.6027.3.15.3.3.1.4 |
| This object indicates whether the transmission of TRAP
notification messages for PFC feature is enabled or disabled. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Integer32 |
|
|
| dellNetPFCPortTable |
1.3.6.1.4.1.6027.3.15.3.3.2 |
| PFC Port table contains the PFC (Priortiy Based Flow Control) features
information specific to this port.
An entry created in the port table populates the entry in this table and
in the following tables in the standard DCBX Mib for this port.
lldpXdot1dcbxConfigPFCTable,
lldpXdot1dcbxLocPFCBasicTable,
lldpXdot1dcbxLocPFCEnableTable,
lldpXdot1dcbxAdminPFCBasicTable,
lldpXdot1dcbxAdminPFCEnableTable.
Deletion of entry in the port table deletes the entry in this table and
all the entries in the above tables in the standatd DCBX mib for this port. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
DellNetPFCPortEntry |
|
| dellNetPFCPortEntry |
1.3.6.1.4.1.6027.3.15.3.3.2.1 |
| An entry containing PFC control parameters and PFC information
for a particular port. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
DellNetPFCPortEntry |
|
|
| dellNetPFCPortNumber |
1.3.6.1.4.1.6027.3.15.3.3.2.1.1 |
| This indicates the interface identifier for which the PFC
configuration is applied. |
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InterfaceIndex |
|
|
| dellNetPFCAdminMode |
1.3.6.1.4.1.6027.3.15.3.3.2.1.2 |
| This object is used to display Admin mode for PFC feature on
the given port.
If mode is 'on(1)',PFC feature is enabled on this port.
PFC configurations, either from this system or
the remote system will take effect based on DCBX negotiations.
If mode is 'off(2)',PFC feature is disabled on this port.
Operational(local) parameters is same as Admin Configuration
Parameters. But Operational(local) parameters do not have any impact
in the system.dellNetPFCDcbxOperState becomes up if remote is also disabled
The Operational(local) parameters do not have any impact in
the system if this object value is 'on(1)'
and dellNetPFCModuleStatus is disabled. dellNetPFCDcbxOperState
will be in 'Off' State. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DcbAdminMode |
|
|
| dellNetPFCDcbxOperState |
1.3.6.1.4.1.6027.3.15.3.3.2.1.3 |
| This object is used to display the current state of the
DCBX state machine for the PFC feature on the given port.
If state is Off '(0)', then PFC Operational(local) parameters
will be same as PFC Admin Configuration Parameters and will
not have any impact in the system(hardware).
If state is init '(1)', then PFC Operational(local) parameters
will be same as PFC Admin Configuration Parameters.
If state is rxrecommended '(2)',then PFC Operational(local) parameters
will be same as PFC Remote Parameters.
internallypropagated '(3)', In this state all the Operational(local)
parameters for the feature will be same as the internal propagated
information from the config source. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DcbState |
|
|
| dellNetPFCDcbxStateMachine |
1.3.6.1.4.1.6027.3.15.3.3.2.1.4 |
| This object is used to display the DCBX state machine
type that is used by the PFC feature on the given port. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DcbStateMachineType |
|
|
| dellNetPFCOperStatus |
1.3.6.1.4.1.6027.3.15.3.3.2.1.5 |
| This object gives information on the operational status of PFC
on the given port.
Enabled(1) indicates PFC on the port is in sync with the remote
and is operationally up.
Disabled(2) indicates PFC on the port is operationally disabled. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
EnabledStatus |
|
|
| dellNetPFCClearTLVCounters |
1.3.6.1.4.1.6027.3.15.3.3.2.1.6 |
| This object when set to TRUE, clears the following counters
associated with a Port:
dellNetPFCTxTLVCounter,
dellNetPFCRxTLVCounter,
dellNetPFCRxTLVErrors.
Setting this object to FALSE has no effect.
This object always returns FALSE when read. |
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| dellNetPFCTxTLVCounter |
1.3.6.1.4.1.6027.3.15.3.3.2.1.7 |
| This object is used to keep track of the number of PFC TLV
that are transmitted from this port. This counter will be
incremented every time when there is PFC TLV is generated
and transmitted to the LLDP. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| dellNetPFCRxTLVCounter |
1.3.6.1.4.1.6027.3.15.3.3.2.1.8 |
| This object is used to keep track of the number of PFC TLV
that are received in this port. This counter will be
incremented every time when there is PFC TLV is received
from the LLDP. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| dellNetPFCRxTLVErrors |
1.3.6.1.4.1.6027.3.15.3.3.2.1.9 |
| This object is used to keep track of number of malformed TLVs received by PFC.
This counter will be incremented every time a PFC-TLV is dropped by PFC. |
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| dellNetDcbTrapPortNumber |
1.3.6.1.4.1.6027.3.15.4.1.1 |
| This object refers to the Port number for which the DCBX feature
is enabled. And will be used in sending the feature port specific Traps. |
| Status: current |
Access: accessible-for-notify |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| dellNetDcbPeerUpStatus |
1.3.6.1.4.1.6027.3.15.4.1.2 |
| This object refers to the DCBX Peer Up or Peer down status
on the port.
If the value is 'true', then the DCBX Peer will be present
and UP.
If the value is 'false', then the DCBX Peer will be absent
and DOWN. |
| Status: current |
Access: accessible-for-notify |
| OBJECT-TYPE |
|
|
|
| |
TruthValue |
|
|
| dellNetETSModuleStatusTrap |
1.3.6.1.4.1.6027.3.15.4.0.1 |
| This trap is generated when there is a change in the ETS Module
status. This trap is generated only if dellNetETSGlobalEnableTrap
is enabled to send the trap. |
| Status: current |
Access: accessible-for-notify |
| NOTIFICATION-TYPE |
|
|
|
| dellNetETSPortAdminStatusTrap |
1.3.6.1.4.1.6027.3.15.4.0.2 |
| This trap is generated in the following conditions.
Whenever there is a change in the ETS Admin status and the
dellNetETSGlobalEnableTrap is enabled to send the trap
for ETS Admin mode change. |
| Status: current |
Access: accessible-for-notify |
| NOTIFICATION-TYPE |
|
|
|
| dellNetETSPortPeerStatusTrap |
1.3.6.1.4.1.6027.3.15.4.0.3 |
| This trap is generated in the following conditions.
Whenever there is a change in the DCBX Peer Status and the
dellNetETSGlobalEnableTrap is enabled
to send the trap for Peer Up or Peer Down. |
| Status: current |
Access: accessible-for-notify |
| NOTIFICATION-TYPE |
|
|
|
| dellNetETSPortDcbxOperStateTrap |
1.3.6.1.4.1.6027.3.15.4.0.4 |
| This trap is generated in the following conditions.
Whenever there is a change in the ETS Operational State and the
dellNetETSGlobalEnableTrap is enabled
to send the trap for ETS state machine state change. |
| Status: current |
Access: accessible-for-notify |
| NOTIFICATION-TYPE |
|
|
|
| dellNetPFCModuleStatusTrap |
1.3.6.1.4.1.6027.3.15.4.0.5 |
| This trap is generated when there is a change in the PFC Module
status is enabled. This trap is generated only if
dellNetPFCGlobalEnableTrap is enabled to send the trap. |
| Status: current |
Access: accessible-for-notify |
| NOTIFICATION-TYPE |
|
|
|
| dellNetPFCPortAdminStatusTrap |
1.3.6.1.4.1.6027.3.15.4.0.6 |
| This trap is generated in the following conditions.
Whenever there is a change in the PFC Admin Status and the
dellNetPFCGlobalEnableTrap is enabled
to send the trap for PFC Admin Status change. |
| Status: current |
Access: accessible-for-notify |
| NOTIFICATION-TYPE |
|
|
|
| dellNetPFCPortPeerStatusTrap |
1.3.6.1.4.1.6027.3.15.4.0.7 |
| This trap is generated in the following conditions.
Whenever there is a change in the DCBX Peer Status and the
dellNetPFCGlobalEnableTrap is enabled
to send the trap for Peer Up or Peer Down. |
| Status: current |
Access: accessible-for-notify |
| NOTIFICATION-TYPE |
|
|
|
| dellNetPFCPortDcbxOperStateTrap |
1.3.6.1.4.1.6027.3.15.4.0.8 |
| This trap is generated in the following conditions.
Whenever there is a change in the PFC Operational State and the
dellNetPFCGlobalEnableTrap is enabled
to send the trap for PFC state machine state change. |
| Status: current |
Access: accessible-for-notify |
| NOTIFICATION-TYPE |
|
|
|
| dellNetDCBMibComplianceRev1 |
1.3.6.1.4.1.6027.3.15.5.1.1 |
| The compliance statement for Dell Networking OS product which implement the
Dell Networking OS dcbx MIB. |
| Status: current |
Access: accessible-for-notify |
| MODULE-COMPLIANCE |
|
|
|
| dellNetDCBMibCompliance |
1.3.6.1.4.1.6027.3.15.5.1.2 |
| The compliance statement for Dell Networking OS product which implement the
Dell Networking OS dcb MIB. This module consists of the obsolete MIB objects. |
| Status: obsolete |
Access: accessible-for-notify |
| MODULE-COMPLIANCE |
|
|
|
| dellNetDcbSystemObjectGroup |
1.3.6.1.4.1.6027.3.15.5.2.1 |
| This group represents a collection of objects providing the
DCB system information. |
| Status: current |
Access: accessible-for-notify |
| OBJECT-GROUP |
|
|
|
| dellNetDcbObjectGroup |
1.3.6.1.4.1.6027.3.15.5.2.2 |
| This group represents a collection of objects providing the
information on the DCB control parameters for a particular port. |
| Status: obsolete |
Access: accessible-for-notify |
| OBJECT-GROUP |
|
|
|
| dellNetDcbxScalarsGroup |
1.3.6.1.4.1.6027.3.15.5.2.3 |
| This group represents the DCBX scalars in the DellNet DCB mib. |
| Status: current |
Access: accessible-for-notify |
| OBJECT-GROUP |
|
|
|
| dellNetDCBXPortTableGroup |
1.3.6.1.4.1.6027.3.15.5.2.4 |
| This group contains the collection of objects describing the
DCBX specific information on the particular port. |
| Status: current |
Access: accessible-for-notify |
| OBJECT-GROUP |
|
|
|
| dellNetETSScalarsGroup |
1.3.6.1.4.1.6027.3.15.5.2.5 |
| This object represents the collection of objects providing the ETS
Information on the system. |
| Status: current |
Access: accessible-for-notify |
| OBJECT-GROUP |
|
|
|
| dellNetETSPortTableGroup |
1.3.6.1.4.1.6027.3.15.5.2.6 |
| This object group represents the collection of objects providing
ETS specific status information on a specific port. |
| Status: current |
Access: accessible-for-notify |
| OBJECT-GROUP |
|
|
|
| dellNetPFCScalarsGroup |
1.3.6.1.4.1.6027.3.15.5.2.7 |
| This group represents a collection of objects providing the system
information related to PFC. |
| Status: current |
Access: accessible-for-notify |
| OBJECT-GROUP |
|
|
|
| dellNetPFCPortTableGroup |
1.3.6.1.4.1.6027.3.15.5.2.8 |
| This group represents a collection of objects providing the
PFC specific status information per port. |
| Status: current |
Access: accessible-for-notify |
| OBJECT-GROUP |
|
|
|
| dellNetDCBNotificationObjectsGroup |
1.3.6.1.4.1.6027.3.15.5.2.9 |
| This object group represents the collection of objects used by the
notification group dellNetDCBNotificationsGroup. |
| Status: current |
Access: accessible-for-notify |
| OBJECT-GROUP |
|
|
|
| dellNetDCBNotificationsGroup |
1.3.6.1.4.1.6027.3.15.5.2.10 |
| A collection on notification objects in the DellNet-DCB mib |
| Status: current |
Access: accessible-for-notify |
| NOTIFICATION-GROUP |
|
|
|