DATASMART-MIB

File: DATASMART-MIB.mib (208900 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC-1215

Imported symbols

enterprises Gauge IpAddress
Counter TimeTicks OBJECT-TYPE
TRAP-TYPE

Defined Types

DLCI  
INTEGER 1..1023    

Counter32  
Counter    

DisplayString  
STRING    

DsRpUsrTmCntEntry  
SEQUENCE    
  dsRpUsrTmCntIndex INTEGER
  dsRpUsrTmCntSecs INTEGER
  dsRpUsrTmCnt15Mins INTEGER
  dsRpUsrTmCntDays INTEGER

DsRpUsrCurEntry  
SEQUENCE    
  dsRpUsrCurIndex INTEGER
  dsRpUsrCurEE Gauge
  dsRpUsrCurES Gauge
  dsRpUsrCurBES Gauge
  dsRpUsrCurSES Gauge
  dsRpUsrCurUAS Gauge
  dsRpUsrCurCSS Gauge
  dsRpUsrCurDM Gauge
  dsRpUsrCurStatus DisplayString

DsRpUsrIntvlEntry  
SEQUENCE    
  dsRpUsrIntvlIndex INTEGER
  dsRpUsrIntvlNum INTEGER
  dsRpUsrIntvlEE Gauge
  dsRpUsrIntvlES Gauge
  dsRpUsrIntvlBES Gauge
  dsRpUsrIntvlSES Gauge
  dsRpUsrIntvlUAS Gauge
  dsRpUsrIntvlCSS Gauge
  dsRpUsrIntvlDM Gauge
  dsRpUsrIntvlStatus DisplayString

DsRpUsrTotalEntry  
SEQUENCE    
  dsRpUsrTotalIndex INTEGER
  dsRpUsrTotalEE Gauge
  dsRpUsrTotalES Gauge
  dsRpUsrTotalBES Gauge
  dsRpUsrTotalSES Gauge
  dsRpUsrTotalUAS Gauge
  dsRpUsrTotalCSS Gauge
  dsRpUsrTotalDM Gauge
  dsRpUsrTotalStatus DisplayString

DsRpUsrDayEntry  
SEQUENCE    
  dsRpUsrDayIndex INTEGER
  dsRpUsrDayNum INTEGER
  dsRpUsrDayEE Gauge
  dsRpUsrDayES Gauge
  dsRpUsrDayBES Gauge
  dsRpUsrDaySES Gauge
  dsRpUsrDayUAS Gauge
  dsRpUsrDayCSS Gauge
  dsRpUsrDayDM Gauge
  dsRpUsrDayStatus DisplayString

DsRpCarIntvlEntry  
SEQUENCE    
  dsRpCarIntvlNum INTEGER
  dsRpCarIntvlEE Gauge
  dsRpCarIntvlES Gauge
  dsRpCarIntvlBES Gauge
  dsRpCarIntvlSES Gauge
  dsRpCarIntvlUAS Gauge
  dsRpCarIntvlCSS Gauge
  dsRpCarIntvlLOFC Gauge

DsRpStEntry  
SEQUENCE    
  dsRpStIndex INTEGER
  dsRpStEsfErrors Counter
  dsRpStCrcErrors Counter
  dsRpStOofErrors Counter
  dsRpStFrameBitErrors Counter
  dsRpStBPVs Counter
  dsRpStControlledSlips Counter
  dsRpStYellowEvents Counter
  dsRpStAISEvents Counter
  dsRpStLOFEvents Counter
  dsRpStLOSEvents Counter
  dsRpStFarEndBlkErrors Counter
  dsRpStRemFrameAlmEvts Counter
  dsRpStRemMFrameAlmEvts Counter
  dsRpStLOTS16MFrameEvts Counter
  dsRpStZeroCounters INTEGER

DsRpAhrEntry  
SEQUENCE    
  dsRpAhrIndex INTEGER
  dsRpAhrStr DisplayString

DsRpShrEntry  
SEQUENCE    
  dsRpShrIndex INTEGER
  dsRpShrDateTime DisplayString
  dsRpShrEventType INTEGER
  dsRpShrComments DisplayString

DsRpFrTmCntEntry  
SEQUENCE    
  dsRpFrTmCntDir INTEGER
  dsRpFrTmCntSecs INTEGER
  dsRpFrTmCnt2Hrs INTEGER
  dsRpFrTmCntDays INTEGER

DsRpFrPre15MEntry  
SEQUENCE    
  dsRpFrPre15MDir INTEGER
  dsRpFrPre15MVcIndex INTEGER
  dsRpFrPre15MVc INTEGER
  dsRpFrPre15MFrames Counter
  dsRpFrPre15MOctets Counter
  dsRpFrPre15MKbps Gauge
  dsRpFrPre15MFpMax Counter
  dsRpFrPre15MFpAvg Gauge
  dsRpFrPre15MFpLost Counter
  dsRpFrPre15MFpSent Counter
  dsRpFrPre15MStatus DisplayString

DsRpFrCur15MEntry  
SEQUENCE    
  dsRpFrCur15MDir INTEGER
  dsRpFrCur15MVcIndex INTEGER
  dsRpFrCur15MVc INTEGER
  dsRpFrCur15MFrames Counter
  dsRpFrCur15MOctets Counter
  dsRpFrCur15MKbps Gauge
  dsRpFrCur15MFpMax Counter
  dsRpFrCur15MFpAvg Gauge
  dsRpFrCur15MFpLost Counter
  dsRpFrCur15MFpSent Counter
  dsRpFrCur15MFpRmtIp IpAddress
  dsRpFrCur15MFpRmtVc INTEGER
  dsRpFrCur15MStatus DisplayString

DsRpFrCur2HEntry  
SEQUENCE    
  dsRpFrCur2HDir INTEGER
  dsRpFrCur2HVcIndex INTEGER
  dsRpFrCur2HVc INTEGER
  dsRpFrCur2HFrames Counter
  dsRpFrCur2HOctets Counter
  dsRpFrCur2HKbps Gauge
  dsRpFrCur2HFpMax Counter
  dsRpFrCur2HFpAvg Gauge
  dsRpFrCur2HFpLost Counter
  dsRpFrCur2HFpSent Counter
  dsRpFrCur2HStatus DisplayString

DsRpFrIntvl2HEntry  
SEQUENCE    
  dsRpFrIntvl2HDir INTEGER
  dsRpFrIntvl2HVcIndex INTEGER
  dsRpFrIntvl2HNum INTEGER
  dsRpFrIntvl2HVc INTEGER
  dsRpFrIntvl2HFrames Counter
  dsRpFrIntvl2HOctets Counter
  dsRpFrIntvl2HKbps Gauge
  dsRpFrIntvl2HFpMax Counter
  dsRpFrIntvl2HFpAvg Gauge
  dsRpFrIntvl2HFpLost Counter
  dsRpFrIntvl2HFpSent Counter
  dsRpFrIntvl2HStatus DisplayString

DsRpFrTotalEntry  
SEQUENCE    
  dsRpFrTotalDir INTEGER
  dsRpFrTotalVcIndex INTEGER
  dsRpFrTotalVc INTEGER
  dsRpFrTotalFrames Counter
  dsRpFrTotalOctets Counter
  dsRpFrTotalKbps Gauge
  dsRpFrTotalFpMax Counter
  dsRpFrTotalFpAvg Gauge
  dsRpFrTotalFpLost Counter
  dsRpFrTotalFpSent Counter
  dsRpFrTotalStatus DisplayString

DsRpFrDayEntry  
SEQUENCE    
  dsRpFrDayDir INTEGER
  dsRpFrDayVcIndex INTEGER
  dsRpFrDayNum INTEGER
  dsRpFrDayVc INTEGER
  dsRpFrDayFrames Counter
  dsRpFrDayOctets Counter
  dsRpFrDayKbps Gauge
  dsRpFrDayFpMax Counter
  dsRpFrDayFpAvg Gauge
  dsRpFrDayFpLost Counter
  dsRpFrDayFpSent Counter
  dsRpFrDayStatus DisplayString

DsRpFrUrEntry  
SEQUENCE    
  dsRpFrUrDir INTEGER
  dsRpFrUrVcIndex INTEGER
  dsRpFrUrVc INTEGER
  dsRpFrUrCIRExceeded Counter
  dsRpFrUrCIRExceededOctets Counter
  dsRpFrUrEIRExceeded Counter
  dsRpFrUrEIRExceededOctets Counter

DsRpDdsEntry  
SEQUENCE    
  dsRpDdsIfIndex INTEGER
  dsRpDdsAvailableSecs Counter32
  dsRpDdsTotalSecs Counter32
  dsRpDdsBPVs Counter32

DsDcEntry  
SEQUENCE    
  dsDcIndex INTEGER
  dsDcDataInvert INTEGER
  dsDcInterface INTEGER
  dsDcClockSource INTEGER
  dsDcXmtClkInvert INTEGER
  dsDcRcvClkInvert INTEGER
  dsDcIdleChar INTEGER
  dsDcLOSInput INTEGER

DsFcEntry  
SEQUENCE    
  dsFcTableIndex INTEGER
  dsFcChanIndex INTEGER
  dsFcChanMap INTEGER

DsAmcTrapEntry  
SEQUENCE    
  dsAmcTrapType INTEGER
  dsAmcTrapStatus INTEGER

DsAmcScrnEntry  
SEQUENCE    
  dsAmcScrnIndex INTEGER
  dsAmcScrnIpAddr IpAddress
  dsAmcScrnIpMask IpAddress

DsAmcTrapDestEntry  
SEQUENCE    
  dsAmcTrapDestIndex INTEGER
  dsAmcTrapDestIpAddr IpAddress
  dsAmcTrapDestVc INTEGER
  dsAmcTrapDestPort INTEGER

Defined Values

datasmart 1.3.6.1.4.1.181.2.2
OBJECT IDENTIFIER    

dsSs 1.3.6.1.4.1.181.2.2.1
OBJECT IDENTIFIER    

dsRp 1.3.6.1.4.1.181.2.2.2
OBJECT IDENTIFIER    

dsLm 1.3.6.1.4.1.181.2.2.3
OBJECT IDENTIFIER    

dsRm 1.3.6.1.4.1.181.2.2.4
OBJECT IDENTIFIER    

dsAc 1.3.6.1.4.1.181.2.2.5
OBJECT IDENTIFIER    

dsCc 1.3.6.1.4.1.181.2.2.6
OBJECT IDENTIFIER    

dsDc 1.3.6.1.4.1.181.2.2.7
OBJECT IDENTIFIER    

dsFc 1.3.6.1.4.1.181.2.2.8
OBJECT IDENTIFIER    

dsFmc 1.3.6.1.4.1.181.2.2.9
OBJECT IDENTIFIER    

dsMc 1.3.6.1.4.1.181.2.2.10
OBJECT IDENTIFIER    

dsNc 1.3.6.1.4.1.181.2.2.11
OBJECT IDENTIFIER    

dsSc 1.3.6.1.4.1.181.2.2.12
OBJECT IDENTIFIER    

dsTc 1.3.6.1.4.1.181.2.2.13
OBJECT IDENTIFIER    

dsFp 1.3.6.1.4.1.181.2.2.14
OBJECT IDENTIFIER    

dsSsAlarmSource 1.3.6.1.4.1.181.2.2.1.1
If the alarm is occuring on a port, this object states which port.
OBJECT-TYPE    
  INTEGER ssSourceNone(1), ssSourceNi(2), ssSourceTi(3), ssSourceDp1(4), ssSourceDp2(5), ssSourceSystem(6)  

dsSsAlarmState 1.3.6.1.4.1.181.2.2.1.2
The alarm state the system is currently in.
OBJECT-TYPE    
  INTEGER ssStateNone(1), ssStateEcf(2), ssStateLos(3), ssStateAis(4), ssStateOof(5), ssStateBer(6), ssStateYel(7), ssStateRfa(8), ssStateRma(9), ssStateOmf(10), ssStateEer(11), ssStateDds(12), ssStateOos(13)  

dsSsLoopback 1.3.6.1.4.1.181.2.2.1.3
The loopback the system is currently performing.
OBJECT-TYPE    
  INTEGER ssLbkNone(1), ssLbkRemLlb(2), ssLbkRemPlb(3), ssLbkRemDp1(4), ssLbkRemDp2(5), ssLbkLlb(6), ssLbkLoc(7), ssLbkPlb(8), ssLbkTlb(9), ssLbkDp1(10), ssLbkDp2(11), ssLbkDt1(12), ssLbkDt2(13), ssLbkCsu(14), ssLbkDsu(15), ssLbkDpdt(16)  

dsSsPowerStatus 1.3.6.1.4.1.181.2.2.1.4
The status of the A and B power inputs on the universal shelf. The possible values are: VALUE DESCRIPTION ssBothOff(1) A off, B off ssAOnBOff(2) A on, B off ssAOffBOn(3) A off, B on ssBothOn(4) A on, B on This is only available on models 558 and 538
OBJECT-TYPE    
  INTEGER ssBothOff(1), ssAOnBOff(2), ssAOffBOn(3), ssBothOn(4)  

dsRpUsr 1.3.6.1.4.1.181.2.2.2.1
OBJECT IDENTIFIER    

dsRpCar 1.3.6.1.4.1.181.2.2.2.2
OBJECT IDENTIFIER    

dsRpStat 1.3.6.1.4.1.181.2.2.2.3
OBJECT IDENTIFIER    

dsRpPl 1.3.6.1.4.1.181.2.2.2.4
OBJECT IDENTIFIER    

dsRpFr 1.3.6.1.4.1.181.2.2.2.10
OBJECT IDENTIFIER    

dsRpUsrTmCntTable 1.3.6.1.4.1.181.2.2.2.1.1
The User Time Counts Table. This table contains information about the number of seconds in the current 15-minute interval, the number of complete 15-minute intervals in the Interval tabl, and the number of days in the Day table.
OBJECT-TYPE    
  SEQUENCE OF  
    DsRpUsrTmCntEntry

dsRpUsrTmCntEntry 1.3.6.1.4.1.181.2.2.2.1.1.1
An entry in the User Time Counts Table.
OBJECT-TYPE    
  DsRpUsrTmCntEntry  

dsRpUsrTmCntIndex 1.3.6.1.4.1.181.2.2.2.1.1.1.1
The index to the User Time Counts Table. The valid indices are: VALUE DESCRIPTION 1 Network Interface 2 Terminal Interface 3 Far End Network Interface
OBJECT-TYPE    
  INTEGER 1..3  

dsRpUsrTmCntSecs 1.3.6.1.4.1.181.2.2.2.1.1.1.2
The number of seconds in the current 15-minute interval.
OBJECT-TYPE    
  INTEGER 0..899  

dsRpUsrTmCnt15Mins 1.3.6.1.4.1.181.2.2.2.1.1.1.3
The number of completed 15-minute intervals in the Interval Table.
OBJECT-TYPE    
  INTEGER 0..96  

dsRpUsrTmCntDays 1.3.6.1.4.1.181.2.2.2.1.1.1.4
The number of completed days in the Day Table.
OBJECT-TYPE    
  INTEGER 0..7  

dsRpUsrCurTable 1.3.6.1.4.1.181.2.2.2.1.2
The User Current Table. This table contains performance information from the current 15-minute interval for the Network, Terminal, and Far End Network Interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    DsRpUsrCurEntry

dsRpUsrCurEntry 1.3.6.1.4.1.181.2.2.2.1.2.1
An entry in the User Current Table.
OBJECT-TYPE    
  DsRpUsrCurEntry  

dsRpUsrCurIndex 1.3.6.1.4.1.181.2.2.2.1.2.1.1
The index for the User Current Table. The valid values for this index are: VALUE DESCRIPTION 1 Network Interface 2 Terminal Interface 3 Far End Network Interface
OBJECT-TYPE    
  INTEGER 1..3  

dsRpUsrCurEE 1.3.6.1.4.1.181.2.2.2.1.2.1.2
The number of Event Errors encountered by a DS1/E1 interface in the current 15-minute interval.
OBJECT-TYPE    
  Gauge  

dsRpUsrCurES 1.3.6.1.4.1.181.2.2.2.1.2.1.3
The number of Errored Seconds encountered by a DS1/E1 interface in the current 15-minute interval.
OBJECT-TYPE    
  Gauge  

dsRpUsrCurBES 1.3.6.1.4.1.181.2.2.2.1.2.1.4
The number of Bursty Errored Seconds encountered by a DS1/E1 interface in the current 15-minute interval.
OBJECT-TYPE    
  Gauge  

dsRpUsrCurSES 1.3.6.1.4.1.181.2.2.2.1.2.1.5
The number of Severely Srrored Seconds encountered by a DS1/E1 intervace in the current 15-minute interval.
OBJECT-TYPE    
  Gauge  

dsRpUsrCurUAS 1.3.6.1.4.1.181.2.2.2.1.2.1.6
The number of Unavailable Seconds encountered by a DS1/E1 interface in the current 15-minute interval.
OBJECT-TYPE    
  Gauge  

dsRpUsrCurCSS 1.3.6.1.4.1.181.2.2.2.1.2.1.7
The number of Controlled Slip Seconds encountered by a DS1/E1 interface in the current 15-minute interval.
OBJECT-TYPE    
  Gauge  

dsRpUsrCurDM 1.3.6.1.4.1.181.2.2.2.1.2.1.8
The number of Degraded Minutes encountered by a DS1/E1 interface in the current 15-minute interval.
OBJECT-TYPE    
  Gauge  

dsRpUsrCurStatus 1.3.6.1.4.1.181.2.2.2.1.2.1.9
The error conditions encountered by a DS1/E1 interface in the current 15-minute interval. The error conditions are signified by a single character. The possible values are: VALUE DESCRIPTION C A CRC error has been detected on the received T1/E1 signal B A bipolar (line) violation has occurred on the received T1/E1 signal L A LOS condition (but not necessarily an alarm) has occurred on the received T1/E1 signal O An OOF condition (but not necessarily an alarm) has occurred on the received T1/E1 E An EER condition (but not necessarily an alarm) has occurred on the received T1/E1 signal A An AIS condition (but not necessarily an alarm) has occurred on the received T1/E1 signal Y A Yellow alarm has occurred on the received T1/E1 signal @ There is an active alarm T There is a loop back, code generation, or BERT active N The unit was without power
OBJECT-TYPE    
  DisplayString Size(0..10)  

dsRpUsrIntvlTable 1.3.6.1.4.1.181.2.2.2.1.3
The User Interval Table. This table contains performance information for the past 24 hours, broken down by 15-minute intervals for the Network, Terminal, and Far End Network Interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    DsRpUsrIntvlEntry

dsRpUsrIntvlEntry 1.3.6.1.4.1.181.2.2.2.1.3.1
An entry in the User Interval Table.
OBJECT-TYPE    
  DsRpUsrIntvlEntry  

dsRpUsrIntvlIndex 1.3.6.1.4.1.181.2.2.2.1.3.1.1
The index for the User Interval Table. The valid values for this index are: VALUE DESCRIPTION 1 Network Interface 2 Terminal Interface 3 Far End Network Interface
OBJECT-TYPE    
  INTEGER  

dsRpUsrIntvlNum 1.3.6.1.4.1.181.2.2.2.1.3.1.2
This is the interval number of the User Interval Table. It will be the number of completed 15-minute intervals since the unit has been powered up. After 24 hours, this value remains constant at 96 intervals.
OBJECT-TYPE    
  INTEGER 1..96  

dsRpUsrIntvlEE 1.3.6.1.4.1.181.2.2.2.1.3.1.3
The number of Event Errors encountered by a DS1/E1 interface in one of the previous 96 15-minute intervals.
OBJECT-TYPE    
  Gauge  

dsRpUsrIntvlES 1.3.6.1.4.1.181.2.2.2.1.3.1.4
The number of Errored Seconds encountered by a DS1/E1 interface in one of the previous 96 15-minute intervals.
OBJECT-TYPE    
  Gauge  

dsRpUsrIntvlBES 1.3.6.1.4.1.181.2.2.2.1.3.1.5
The number of Bursty Errored Seconds encountered by a DS1/E1 interface in one of the pervious 96 15-minute intervals.
OBJECT-TYPE    
  Gauge  

dsRpUsrIntvlSES 1.3.6.1.4.1.181.2.2.2.1.3.1.6
The number of Severely Errored Seconds encountered by a DS1/E1 interface in one of the previous 96 15-minute intervals.
OBJECT-TYPE    
  Gauge  

dsRpUsrIntvlUAS 1.3.6.1.4.1.181.2.2.2.1.3.1.7
The number of Unavailable Seconds encountered by a DS1/E1 interface in one of the previous 96 15-minute intervals.
OBJECT-TYPE    
  Gauge  

dsRpUsrIntvlCSS 1.3.6.1.4.1.181.2.2.2.1.3.1.8
The number of Controlled Slip Seconds encountered by a DS1/E1 interface in one of the previous 96 15-minute intervals.
OBJECT-TYPE    
  Gauge  

dsRpUsrIntvlDM 1.3.6.1.4.1.181.2.2.2.1.3.1.9
The number of Degraded Minutes encountered by a DS1/E1 interface in one of the previous 96 15-minute intervals.
OBJECT-TYPE    
  Gauge  

dsRpUsrIntvlStatus 1.3.6.1.4.1.181.2.2.2.1.3.1.10
The error conditions encountered by a DS1/E1 interface in one of the pervious 96 15-minute intervals. The error conditions are signified by a single character. The possible values are: VALUE DESCRIPTION C A CRC error has been detected on the received T1/E1 signal B A bipolar (line) violation has occurred on the received T1/E1 signal L A LOS condition (but not necessarily an alarm) has occurred on the received T1/E1 signal O An OOF condition (but not necessarily an alarm) has occurred on the received T1/E1 E An EER condition (but not necessarily an alarm) has occurred on the received T1/E1 signal A An AIS condition (but not necessarily an alarm) has occurred on the received T1/E1 signal Y A Yellow alarm has occurred on the received T1/E1 signal S A controlled slip has occurred on the received T1/E1 signal @ There is an active alarm T There is a loop back, code generation, or BERT active N The unit was without power
OBJECT-TYPE    
  DisplayString Size(0..10)  

dsRpUsrTotalTable 1.3.6.1.4.1.181.2.2.2.1.4
The User Total Table. This table contains performance information for the past 24-hours, for the Network, Terminal, and Far End Network Interfaces. This is a rolling count. When the current 15-minute interval is up, the last entry in the interval table will be removed and the completed 15-minute interval added. At this point the Total Table will be re-calculated.
OBJECT-TYPE    
  SEQUENCE OF  
    DsRpUsrTotalEntry

dsRpUsrTotalEntry 1.3.6.1.4.1.181.2.2.2.1.4.1
An entry in the User Total Table.
OBJECT-TYPE    
  DsRpUsrTotalEntry  

dsRpUsrTotalIndex 1.3.6.1.4.1.181.2.2.2.1.4.1.1
The index for the User Total Table. The valid indices are: VALUE DESCRIPTION 1 Network Interface 2 Terminal Interface 3 Far End Network Interface
OBJECT-TYPE    
  INTEGER  

dsRpUsrTotalEE 1.3.6.1.4.1.181.2.2.2.1.4.1.2
The number of Event Errors encountered by a DS1/E1 interface in the past 24-hours.
OBJECT-TYPE    
  Gauge  

dsRpUsrTotalES 1.3.6.1.4.1.181.2.2.2.1.4.1.3
The number of Errored Seconds encountered by a DS1/E1 interface in the past 24-hours.
OBJECT-TYPE    
  Gauge  

dsRpUsrTotalBES 1.3.6.1.4.1.181.2.2.2.1.4.1.4
The number of Bursty Errored Seconds encountered by a DS1/E1 interface in the past 24-hours.
OBJECT-TYPE    
  Gauge  

dsRpUsrTotalSES 1.3.6.1.4.1.181.2.2.2.1.4.1.5
The number of Severely Errored Seconds encountered by a DS1/E1 interface in the past 24-hours.
OBJECT-TYPE    
  Gauge  

dsRpUsrTotalUAS 1.3.6.1.4.1.181.2.2.2.1.4.1.6
The number of Unavailable Seconds encountered by a DS1/E1 interface in the past 24-hours.
OBJECT-TYPE    
  Gauge  

dsRpUsrTotalCSS 1.3.6.1.4.1.181.2.2.2.1.4.1.7
The number of Controlled Slip Seconds encountered by a DS1/E1 interface in the past 24-hours.
OBJECT-TYPE    
  Gauge  

dsRpUsrTotalDM 1.3.6.1.4.1.181.2.2.2.1.4.1.8
The number of Degraded Minutes encountered by a DS1/E1 interface in the past 24-hours.
OBJECT-TYPE    
  Gauge  

dsRpUsrTotalStatus 1.3.6.1.4.1.181.2.2.2.1.4.1.9
The error conditions encountered by a DS1/E1 interface in the past 24-hours. The error conditions are signified by a single character. The possible values are: VALUE DESCRIPTION C A CRC error has been detected on the received T1/E1 signal B A bipolar (line) violation has occurred on the received T1/E1 signal L A LOS condition (but not necessarily an alarm) has occurred on the received T1/E1 signal O An OOF condition (but not necessarily an alarm) has occurred on the received T1/E1 E An EER condition (but not necessarily an alarm) has occurred on the received T1/E1 signal A An AIS condition (but not necessarily an alarm) has occurred on the received T1/E1 signal Y A Yellow alarm has occurred on the received T1/E1 signal S A controlled slip has occurred on the received T1/E1 signal @ There is an active alarm T There is a loop back, code generation, or BERT active N The unit was without power
OBJECT-TYPE    
  DisplayString Size(0..10)  

dsRpUsrDayTable 1.3.6.1.4.1.181.2.2.2.1.5
After the unit has been powered up for 24 hours, the values from the User Total Table are moved into the first slot in the User Day Table. There are seven entries in the User Day Table, so an entire week's history is maintained. The previous day is always in slot 1.
OBJECT-TYPE    
  SEQUENCE OF  
    DsRpUsrDayEntry

dsRpUsrDayEntry 1.3.6.1.4.1.181.2.2.2.1.5.1
This is an entry in the User Day Table.
OBJECT-TYPE    
  DsRpUsrDayEntry  

dsRpUsrDayIndex 1.3.6.1.4.1.181.2.2.2.1.5.1.1
The User Day Table interface index. The valid indices are: VALUE DESCRIPTION 1 Network Interface 2 Terminal Interface 3 Far End Network Interface
OBJECT-TYPE    
  INTEGER  

dsRpUsrDayNum 1.3.6.1.4.1.181.2.2.2.1.5.1.2
The User Day Table day index. The valid values are 1 day to 7 days.
OBJECT-TYPE    
  INTEGER 1..7  

dsRpUsrDayEE 1.3.6.1.4.1.181.2.2.2.1.5.1.3
The number of Event Errors encountered by a DS1/E1 interface in one of the previous days.
OBJECT-TYPE    
  Gauge  

dsRpUsrDayES 1.3.6.1.4.1.181.2.2.2.1.5.1.4
The number of Errored Seconds encountered by a DS1/E1 interface in one of the previous days.
OBJECT-TYPE    
  Gauge  

dsRpUsrDayBES 1.3.6.1.4.1.181.2.2.2.1.5.1.5
The number of Bursty Errored Seconds encountered by a DS1/E1 interface in one of the previous days.
OBJECT-TYPE    
  Gauge  

dsRpUsrDaySES 1.3.6.1.4.1.181.2.2.2.1.5.1.6
The number of Severely Errored Seconds encountered by a DS1/E1 interface in one of the previous days.
OBJECT-TYPE    
  Gauge  

dsRpUsrDayUAS 1.3.6.1.4.1.181.2.2.2.1.5.1.7
The number of Unavailable Seconds encountered by a DS1/E1 interface in one of the previous days.
OBJECT-TYPE    
  Gauge  

dsRpUsrDayCSS 1.3.6.1.4.1.181.2.2.2.1.5.1.8
The number of Controlled Slip Seconds encountered by a DS1/E1 interface in one of the previous days.
OBJECT-TYPE    
  Gauge  

dsRpUsrDayDM 1.3.6.1.4.1.181.2.2.2.1.5.1.9
The number of Degraded Minutes encountered by a DS1/E1 interface in one of the previous days.
OBJECT-TYPE    
  Gauge  

dsRpUsrDayStatus 1.3.6.1.4.1.181.2.2.2.1.5.1.10
The error conditions encountered by a DS1/E1 interface in one of the previous days. The error conditions are signified by a single character. The possible values are: VALUE DESCRIPTION C A CRC error has been detected on the received T1/E1 signal B A bipolar (line) violation has occurred on the received T1/E1 signal L A LOS condition (but not necessarily an alarm) has occurred on the received T1/E1 signal O An OOF condition (but not necessarily an alarm) has occurred on the received T1/E1 E An EER condition (but not necessarily an alarm) has occurred on the received T1/E1 signal A An AIS condition (but not necessarily an alarm) has occurred on the received T1/E1 signal Y A Yellow alarm has occurred on the received T1/E1 signal S A controlled slip has occurred on the received T1/E1 signal @ There is an active alarm T There is a loop back, code generation, or BERT active N The unit was without power
OBJECT-TYPE    
  DisplayString Size(0..10)  

dsRpCarCntSecs 1.3.6.1.4.1.181.2.2.2.2.1
The number of seconds that have elapsed in the current interval.
OBJECT-TYPE    
  INTEGER 0..899  

dsRpCarCnt15Mins 1.3.6.1.4.1.181.2.2.2.2.2
The number of 15-minute intervals that have elapsed in the current 24-hours.
OBJECT-TYPE    
  INTEGER 0..96  

dsRpCarCur 1.3.6.1.4.1.181.2.2.2.2.3
OBJECT IDENTIFIER    

dsRpCarCurEE 1.3.6.1.4.1.181.2.2.2.2.3.1
The number of Event Errors encountered by the Network Interface in the current 15-minute interval.
OBJECT-TYPE    
  Gauge  

dsRpCarCurES 1.3.6.1.4.1.181.2.2.2.2.3.2
The number of Errored Seconds encountered by the Network Interface in the current 15-minute interval.
OBJECT-TYPE    
  Gauge  

dsRpCarCurBES 1.3.6.1.4.1.181.2.2.2.2.3.3
The number of Bursty Errored Seconds encountered by the Network Interface in the current 15-minute interval.
OBJECT-TYPE    
  Gauge  

dsRpCarCurSES 1.3.6.1.4.1.181.2.2.2.2.3.4
The number of Severely Errored Seconds encountered by the Network Interface in the current 15-minute interval.
OBJECT-TYPE    
  Gauge  

dsRpCarCurUAS 1.3.6.1.4.1.181.2.2.2.2.3.5
The number of Unavailable Seconds encountered by the Network Interface in the current 15-minute interval.
OBJECT-TYPE    
  Gauge  

dsRpCarCurCSS 1.3.6.1.4.1.181.2.2.2.2.3.6
The number of Controlled Slip Seconds encountered by the Network Interface in the current 15-minute interval.
OBJECT-TYPE    
  Gauge  

dsRpCarCurLOFC 1.3.6.1.4.1.181.2.2.2.2.3.7
The Loss of Frame Count for the Network Interface in the current 15-minute interval.
OBJECT-TYPE    
  Gauge  

dsRpCarIntvlTable 1.3.6.1.4.1.181.2.2.2.2.4
This is the Carrier Interval Table. This table contains performance information about the Network Interface.
OBJECT-TYPE    
  SEQUENCE OF  
    DsRpCarIntvlEntry

dsRpCarIntvlEntry 1.3.6.1.4.1.181.2.2.2.2.4.1
This is an entry in the Carrier Interval Table.
OBJECT-TYPE    
  DsRpCarIntvlEntry  

dsRpCarIntvlNum 1.3.6.1.4.1.181.2.2.2.2.4.1.1
The number of the 15-minute interval (1-96) from the previous 24-hour period. 1 is the most recent.
OBJECT-TYPE    
  INTEGER 1..96  

dsRpCarIntvlEE 1.3.6.1.4.1.181.2.2.2.2.4.1.2
The number of Event Errors encountered by the Network Interface in one of the previous 96 15-minute intervals.
OBJECT-TYPE    
  Gauge  

dsRpCarIntvlES 1.3.6.1.4.1.181.2.2.2.2.4.1.3
The number of Errored Seconds encountered by the Network Interface in one of the previous 96 15-minute intervals.
OBJECT-TYPE    
  Gauge  

dsRpCarIntvlBES 1.3.6.1.4.1.181.2.2.2.2.4.1.4
The number of Bursty Errored Seconds encountered by the Network Interface in one of the previous 96 15-minute intervals.
OBJECT-TYPE    
  Gauge  

dsRpCarIntvlSES 1.3.6.1.4.1.181.2.2.2.2.4.1.5
The number of Severely Errored Seconds encountered by the Network Interface in one of the previous 96 15-minute intervals.
OBJECT-TYPE    
  Gauge  

dsRpCarIntvlUAS 1.3.6.1.4.1.181.2.2.2.2.4.1.6
The number of Unavailable Seconds encountered by the Network Interface in one of the previous 96 15-minute intervals.
OBJECT-TYPE    
  Gauge  

dsRpCarIntvlCSS 1.3.6.1.4.1.181.2.2.2.2.4.1.7
The number of Controlled Slip Seconds encountered by the Network Interface in one of the previous 96 15-minute intervals.
OBJECT-TYPE    
  Gauge  

dsRpCarIntvlLOFC 1.3.6.1.4.1.181.2.2.2.2.4.1.8
The Loss of Frame Count fo the Network Interface for one of the previous 96 15-minute intervals.
OBJECT-TYPE    
  Gauge  

dsRpCarTotal 1.3.6.1.4.1.181.2.2.2.2.5
OBJECT IDENTIFIER    

dsRpCarTotalEE 1.3.6.1.4.1.181.2.2.2.2.5.1
The number of Errored Events encountered by the Network Interface in the past 24-hours.
OBJECT-TYPE    
  Gauge  

dsRpCarTotalES 1.3.6.1.4.1.181.2.2.2.2.5.2
The number of Errored Seconds encountered by the Network Interface in the past 24-hours.
OBJECT-TYPE    
  Gauge  

dsRpCarTotalBES 1.3.6.1.4.1.181.2.2.2.2.5.3
The number of Bursty Errored Seconds encountered by the Network Interface in the past 24-hours.
OBJECT-TYPE    
  Gauge  

dsRpCarTotalSES 1.3.6.1.4.1.181.2.2.2.2.5.4
The number of Severely Errored Seconds encountered by the Network Interface in the past 24-hours.
OBJECT-TYPE    
  Gauge  

dsRpCarTotalUAS 1.3.6.1.4.1.181.2.2.2.2.5.5
The number of Unavailable Seconds encountered by the Network Interface in the past 24-hours.
OBJECT-TYPE    
  Gauge  

dsRpCarTotalCSS 1.3.6.1.4.1.181.2.2.2.2.5.6
The number of Controlled Slip Seconds encountered by the Network Interface in the past 24-hours.
OBJECT-TYPE    
  Gauge  

dsRpCarTotalLOFC 1.3.6.1.4.1.181.2.2.2.2.5.7
The Loss of Frame Count for the Network Interface for one of the previous 96 15-minute intervals.
OBJECT-TYPE    
  Gauge  

dsRpStTable 1.3.6.1.4.1.181.2.2.2.3.1
The Statistics Table. This table consists of statistical error counts of various DS1/E1 line conditions. These counts are maintained between power-cycles.
OBJECT-TYPE    
  SEQUENCE OF  
    DsRpStEntry

dsRpStEntry 1.3.6.1.4.1.181.2.2.2.3.1.1
An entry in the Statistics Table.
OBJECT-TYPE    
  DsRpStEntry  

dsRpStIndex 1.3.6.1.4.1.181.2.2.2.3.1.1.1
The index into the Statistics Table. The valid indices are: VALUE DESCRIPTION 1 Network Interface 2 Terminal Interface 3 Far End Network Interface
OBJECT-TYPE    
  INTEGER 1..3  

dsRpStEsfErrors 1.3.6.1.4.1.181.2.2.2.3.1.1.2
The total number of Error Free Seconds since the counters have last been cleared.
OBJECT-TYPE    
  Counter  

dsRpStCrcErrors 1.3.6.1.4.1.181.2.2.2.3.1.1.3
The total number of CRC errors since the counters have last been cleared.
OBJECT-TYPE    
  Counter  

dsRpStOofErrors 1.3.6.1.4.1.181.2.2.2.3.1.1.4
The total number of Out Of Frame errors since the counters have last been cleared.
OBJECT-TYPE    
  Counter  

dsRpStFrameBitErrors 1.3.6.1.4.1.181.2.2.2.3.1.1.5
The total number of Frame Bit errors since the counters have last been cleared.
OBJECT-TYPE    
  Counter  

dsRpStBPVs 1.3.6.1.4.1.181.2.2.2.3.1.1.6
The total number of Bipolar Violations since the counters have last been cleared.
OBJECT-TYPE    
  Counter  

dsRpStControlledSlips 1.3.6.1.4.1.181.2.2.2.3.1.1.7
The total number of Controlled Slips since the counters have last been cleared.
OBJECT-TYPE    
  Counter  

dsRpStYellowEvents 1.3.6.1.4.1.181.2.2.2.3.1.1.8
The total number of Yellow Events since the counters have last been cleared.
OBJECT-TYPE    
  Counter  

dsRpStAISEvents 1.3.6.1.4.1.181.2.2.2.3.1.1.9
The total number of Alarm Indication Siganl events since the counters have last been cleared.
OBJECT-TYPE    
  Counter  

dsRpStLOFEvents 1.3.6.1.4.1.181.2.2.2.3.1.1.10
The total number of Loss of Frame events since the counters have last been cleared.
OBJECT-TYPE    
  Counter  

dsRpStLOSEvents 1.3.6.1.4.1.181.2.2.2.3.1.1.11
The total number of Loss of Signal events since the counters have last been cleared.
OBJECT-TYPE    
  Counter  

dsRpStFarEndBlkErrors 1.3.6.1.4.1.181.2.2.2.3.1.1.12
The total number of Far End Block Errors since the counters were last cleared.
OBJECT-TYPE    
  Counter  

dsRpStRemFrameAlmEvts 1.3.6.1.4.1.181.2.2.2.3.1.1.13
The total number of Remote Frame Alarm events since the counters were last cleared.
OBJECT-TYPE    
  Counter  

dsRpStRemMFrameAlmEvts 1.3.6.1.4.1.181.2.2.2.3.1.1.14
The total number of Remote MultiFrame Alarm events since the counters were last cleared.
OBJECT-TYPE    
  Counter  

dsRpStLOTS16MFrameEvts 1.3.6.1.4.1.181.2.2.2.3.1.1.15
The total number of Loss of TS16MultiFrame events since the counters have been cleared.
OBJECT-TYPE    
  Counter  

dsRpStZeroCounters 1.3.6.1.4.1.181.2.2.2.3.1.1.16
This object will clear the Statistics Table counters when it is set to rpStZeroCounterStart(2). Once the counters have been cleraed, it will return to its normal state of rpStZeroCountersIdle(1).
OBJECT-TYPE    
  INTEGER rpStZeroCountersIdle(1), rpStZeroCountersStart(2)  

dsPlBreak 1.3.6.1.4.1.181.2.2.2.4.1
This object determines if the user interface uses page breaks or 'more' prompts when displaying information which is longer than the defined page length (e.g., output from UNLR or SCV). A page length of 0 will disable both page breaks and 'more' prompts. VALUE DESCRIPTION rpPlLineFeed(1) Use linefeeds for page breaks rpPlMorePrompt(2) Use 'more' prompts for page breaks
OBJECT-TYPE    
  INTEGER rpPlLineFeed(1), rpPlMorePrompt(2)  

dsPlLen 1.3.6.1.4.1.181.2.2.2.4.2
The length of a 'page' of information. When the set number of lines have been displayed, a 'more' prompt or linefeed will be inserted (defined by dsPlBreak). A page length of 0 causes output to scroll continuously without page breaks or 'more' prompts.
OBJECT-TYPE    
  INTEGER 0..70  

dsRpAhrTable 1.3.6.1.4.1.181.2.2.2.5
This is the Alarm History Table. It contains the text messages of the last 20 alarms.
OBJECT-TYPE    
  SEQUENCE OF  
    DsRpAhrEntry

dsRpAhrEntry 1.3.6.1.4.1.181.2.2.2.5.1
An entry in the Alarm History Table.
OBJECT-TYPE    
  DsRpAhrEntry  

dsRpAhrIndex 1.3.6.1.4.1.181.2.2.2.5.1.1
The Alarm History Table index. Index 1 is the most recent alarm.
OBJECT-TYPE    
  INTEGER 1..20  

dsRpAhrStr 1.3.6.1.4.1.181.2.2.2.5.1.2
The alarm message in USER format.
OBJECT-TYPE    
  DisplayString Size(0..80)  

dsRpShrTable 1.3.6.1.4.1.181.2.2.2.6
This is the Security History Report table. It contains entries for events which are considered important from a security standpoint. Examples of such events are 1) incorrect Telnet password entered and 2) source IP address not on IP Screen List. The entries are placed in chronological order, with most recent event first.
OBJECT-TYPE    
  SEQUENCE OF  
    DsRpShrEntry

dsRpShrEntry 1.3.6.1.4.1.181.2.2.2.6.1
An entry in the Security History Report table.
OBJECT-TYPE    
  DsRpShrEntry  

dsRpShrIndex 1.3.6.1.4.1.181.2.2.2.6.1.1
The Security History Report table index. Events are in chronological order. This number ranges between 1 and the value of dsRpShrNumber. Index 1 is the most recent event.
OBJECT-TYPE    
  INTEGER  

dsRpShrDateTime 1.3.6.1.4.1.181.2.2.2.6.1.2
Display string showing date & time that the security related event occurred.
OBJECT-TYPE    
  DisplayString Size(0..80)  

dsRpShrEventType 1.3.6.1.4.1.181.2.2.2.6.1.3
Shows what type of security related event occurred. VALUE DESCRIPTION rpShrTelnetPassword (1) - Incorrect Telnet password entered rpShrSrcIpAddressScreen (2) - Source IP address not on IP Screen List rpShrReadCommString (3) - Incorrect SNMP Read Community String rpShrWriteCommString (4) - Incorrect SNMP Write Community String
OBJECT-TYPE    
  INTEGER rpShrTelnetPassword(1), rpShrSrcIpAddressScreen(2), rpShrReadCommString(3), rpShrWriteCommString(4)  

dsRpShrComments 1.3.6.1.4.1.181.2.2.2.6.1.4
Display string showing additional information specific to the type of event. For example, for events of type rpShrTelnetPassword, the IP address of the remote host is given.
OBJECT-TYPE    
  DisplayString Size(0..80)  

dsRpBes 1.3.6.1.4.1.181.2.2.2.7
The error threshold for Bursty Errored Seconds.
OBJECT-TYPE    
  INTEGER 2..63999  

dsRpSes 1.3.6.1.4.1.181.2.2.2.8
The threshold for Severely Errored Seconds.
OBJECT-TYPE    
  INTEGER 3..64000  

dsRpDm 1.3.6.1.4.1.181.2.2.2.9
The threshold for Degraded Minutes.
OBJECT-TYPE    
  INTEGER 1..64000  

dsRpFrTmCntTable 1.3.6.1.4.1.181.2.2.2.10.1
The FRIB Time Counts Table. This table contains information for the number of seconds in the current 2-hour interval, the number of complete 2-hour intervals in the Interval table, and the number of days in the Day table.
OBJECT-TYPE    
  SEQUENCE OF  
    DsRpFrTmCntEntry

dsRpFrTmCntEntry 1.3.6.1.4.1.181.2.2.2.10.1.1
An entry in the FRIB Time Counts Table.
OBJECT-TYPE    
  DsRpFrTmCntEntry  

dsRpFrTmCntDir 1.3.6.1.4.1.181.2.2.2.10.1.1.1
The direction index to the FRIB Time Counts Table. The valid indices are: VALUE DESCRIPTION 1 Transmit 2 Receive
OBJECT-TYPE    
  INTEGER 1..2  

dsRpFrTmCntSecs 1.3.6.1.4.1.181.2.2.2.10.1.1.2
The number of seconds in the current 2-hour interval.
OBJECT-TYPE    
  INTEGER 0..7200  

dsRpFrTmCnt2Hrs 1.3.6.1.4.1.181.2.2.2.10.1.1.3
The number of completed 2-hour intervals in the Interval Table.
OBJECT-TYPE    
  INTEGER 0..12  

dsRpFrTmCntDays 1.3.6.1.4.1.181.2.2.2.10.1.1.4
The number of completed days in the Day Table.
OBJECT-TYPE    
  INTEGER 0..7  

dsRpFrPre15MTable 1.3.6.1.4.1.181.2.2.2.10.2
The FRIB Previous 15 Min Table. This table contains performance information from the previous 15-minute interval for both the transmit and receive directions of each VC at the Network Interface.
OBJECT-TYPE    
  SEQUENCE OF  
    DsRpFrPre15MEntry

dsRpFrPre15MEntry 1.3.6.1.4.1.181.2.2.2.10.2.1
An entry in the FRIB Previous 15 Min Table.
OBJECT-TYPE    
  DsRpFrPre15MEntry  

dsRpFrPre15MDir 1.3.6.1.4.1.181.2.2.2.10.2.1.1
The direction index to the FRIB Previous 15 Min Table. VALUE DESCRIPTION 1 Transmit 2 Receive
OBJECT-TYPE    
  INTEGER 1..2  

dsRpFrPre15MVcIndex 1.3.6.1.4.1.181.2.2.2.10.2.1.2
The VC index to the FRIB Previous 15 Min Table. The table has 64 entries for indiviual VCs, a value of 1 through 64, and 1 entry for all other VCs, a value of 65.
OBJECT-TYPE    
  INTEGER 1..65  

dsRpFrPre15MVc 1.3.6.1.4.1.181.2.2.2.10.2.1.3
The VC for this entry in the FRIB Previous 15 Min Table.
OBJECT-TYPE    
  INTEGER 1..8388607  

dsRpFrPre15MFrames 1.3.6.1.4.1.181.2.2.2.10.2.1.4
The number of Frame Relay packets transmitted or received during the previous 15-minute interval.
OBJECT-TYPE    
  Counter  

dsRpFrPre15MOctets 1.3.6.1.4.1.181.2.2.2.10.2.1.5
The number of octets transmitted or received during the previous 15-minute interval.
OBJECT-TYPE    
  Counter  

dsRpFrPre15MKbps 1.3.6.1.4.1.181.2.2.2.10.2.1.6
The Kilobit/sec rate for data transmitted or received during the previous 15-minute interval.
OBJECT-TYPE    
  Gauge  

dsRpFrPre15MFpMax 1.3.6.1.4.1.181.2.2.2.10.2.1.7
The maximum FPING roundtrip time (in msec) of all FPINGs on this VC during the previous 15-minute interval.
OBJECT-TYPE    
  Counter  

dsRpFrPre15MFpAvg 1.3.6.1.4.1.181.2.2.2.10.2.1.8
The average FPING roundtrip time (in msec) of all FPINGs on this VC during the previous 15-minute interval.
OBJECT-TYPE    
  Gauge  

dsRpFrPre15MFpLost 1.3.6.1.4.1.181.2.2.2.10.2.1.9
The number of FPINGs responses that were not returned on this VC during the previous 15-minute interval.
OBJECT-TYPE    
  Counter  

dsRpFrPre15MFpSent 1.3.6.1.4.1.181.2.2.2.10.2.1.10
The number of FPINGs transmitted on this VC during the previous 15-minute interval.
OBJECT-TYPE    
  Counter  

dsRpFrPre15MStatus 1.3.6.1.4.1.181.2.2.2.10.2.1.11
The status summary of this VC during the previous 15-minute interval: VALUE DESCRIPTION U VC link is UP D VC link is DOWN B At least one frame had the BECN bit set F At least one frame had the FECN bit set E At least one frame had the DE bit set P The total pipe threshold for utilization was exceeded V The roundtrip threshold for this VC was exceeded
OBJECT-TYPE    
  DisplayString Size(0..7)  

dsRpFrCur15MTable 1.3.6.1.4.1.181.2.2.2.10.3
The FRIB Current 15 Min Table. This table contains performance information from the current 15-minute interval for both the transmit and receive directions of each VC at the Network Interface.
OBJECT-TYPE    
  SEQUENCE OF  
    DsRpFrCur15MEntry

dsRpFrCur15MEntry 1.3.6.1.4.1.181.2.2.2.10.3.1
An entry in the FRIB Current 15 Min Table.
OBJECT-TYPE    
  DsRpFrCur15MEntry  

dsRpFrCur15MDir 1.3.6.1.4.1.181.2.2.2.10.3.1.1
The direction index to the FRIB Current 15 Min Table. VALUE DESCRIPTION 1 Transmit 2 Receive
OBJECT-TYPE    
  INTEGER 1..2  

dsRpFrCur15MVcIndex 1.3.6.1.4.1.181.2.2.2.10.3.1.2
The VC index to the FRIB Current 15 Min Table. The table has 64 entries for indiviual VCs and the 65th entry for all other VCs including errored frames.
OBJECT-TYPE    
  INTEGER 1..65  

dsRpFrCur15MVc 1.3.6.1.4.1.181.2.2.2.10.3.1.3
The VC for this entry in the FRIB Current 15 Min Table.
OBJECT-TYPE    
  INTEGER 1..8388607  

dsRpFrCur15MFrames 1.3.6.1.4.1.181.2.2.2.10.3.1.4
The number of Frame Relay packets transmitted or received during the current 15-minute interval.
OBJECT-TYPE    
  Counter  

dsRpFrCur15MOctets 1.3.6.1.4.1.181.2.2.2.10.3.1.5
The number of octets transmitted or received during the current 15-minute interval.
OBJECT-TYPE    
  Counter  

dsRpFrCur15MKbps 1.3.6.1.4.1.181.2.2.2.10.3.1.6
The Kilobit/sec rate for data transmitted or received during the current 15-minute interval.
OBJECT-TYPE    
  Gauge  

dsRpFrCur15MFpMax 1.3.6.1.4.1.181.2.2.2.10.3.1.7
The maximum FPING roundtrip time (in msec) of all FPINGs on this VC during the current 15-minute interval.
OBJECT-TYPE    
  Counter  

dsRpFrCur15MFpAvg 1.3.6.1.4.1.181.2.2.2.10.3.1.8
The average FPING roundtrip time (in msec) of all FPINGs on this VC during the current 15-minute interval.
OBJECT-TYPE    
  Gauge  

dsRpFrCur15MFpLost 1.3.6.1.4.1.181.2.2.2.10.3.1.9
The number of FPINGs responses received on this VC during the current 15-minute interval.
OBJECT-TYPE    
  Counter  

dsRpFrCur15MFpSent 1.3.6.1.4.1.181.2.2.2.10.3.1.10
The number of FPINGs transmitted on this VC during the current 15-minute interval.
OBJECT-TYPE    
  Counter  

dsRpFrCur15MFpRmtIp 1.3.6.1.4.1.181.2.2.2.10.3.1.11
The IP Address of the unit at the remote end of the VC.
OBJECT-TYPE    
  IpAddress  

dsRpFrCur15MFpRmtVc 1.3.6.1.4.1.181.2.2.2.10.3.1.12
The VC number at the remote end of the VC.
OBJECT-TYPE    
  INTEGER 0..8388607  

dsRpFrCur15MStatus 1.3.6.1.4.1.181.2.2.2.10.3.1.13
The status summary of this VC during the current 15-minute interval: VALUE DESCRIPTION U VC link is UP D VC link is DOWN B At least one frame had the BECN bit set F At least one frame had the FECN bit set E At least one frame had the DE bit set P The total pipe threshold for utilization was exceeded V The roundtrip threshold for this VC was exceeded
OBJECT-TYPE    
  DisplayString Size(0..7)  

dsRpFrCur2HTable 1.3.6.1.4.1.181.2.2.2.10.4
The FRIB Current 2Hr Table. This table contains performance information from the current 2-hour interval for both the transmit and receive directions of each VC at the Network Interface.
OBJECT-TYPE    
  SEQUENCE OF  
    DsRpFrCur2HEntry

dsRpFrCur2HEntry 1.3.6.1.4.1.181.2.2.2.10.4.1
An entry in the FRIB Current 2Hr Table.
OBJECT-TYPE    
  DsRpFrCur2HEntry  

dsRpFrCur2HDir 1.3.6.1.4.1.181.2.2.2.10.4.1.1
The direction index to the FRIB Current 2Hr Table. VALUE DESCRIPTION 1 Transmit 2 Receive
OBJECT-TYPE    
  INTEGER 1..2  

dsRpFrCur2HVcIndex 1.3.6.1.4.1.181.2.2.2.10.4.1.2
The VC index to the FRIB Current 2Hr Table. The table has 64 entries for indiviual VCs and 1 entry for all other VCs.
OBJECT-TYPE    
  INTEGER 1..65  

dsRpFrCur2HVc 1.3.6.1.4.1.181.2.2.2.10.4.1.3
The VC for this entry in the FRIB Current 2Hr Table.
OBJECT-TYPE    
  INTEGER 1..8388607  

dsRpFrCur2HFrames 1.3.6.1.4.1.181.2.2.2.10.4.1.4
The number of Frame Relay packets transmitted or received during the current 2-hour interval.
OBJECT-TYPE    
  Counter  

dsRpFrCur2HOctets 1.3.6.1.4.1.181.2.2.2.10.4.1.5
The number of octets transmitted or received during the current 2-hour interval.
OBJECT-TYPE    
  Counter  

dsRpFrCur2HKbps 1.3.6.1.4.1.181.2.2.2.10.4.1.6
The Kilobit/sec rate for data transmitted or received during the current 2-hour interval.
OBJECT-TYPE    
  Gauge  

dsRpFrCur2HFpMax 1.3.6.1.4.1.181.2.2.2.10.4.1.7
The maximum FPING roundtrip time (in msec) of all FPINGs on this VC during the current 2-hour interval.
OBJECT-TYPE    
  Counter  

dsRpFrCur2HFpAvg 1.3.6.1.4.1.181.2.2.2.10.4.1.8
The average FPING roundtrip time (in msec) of all FPINGs on this VC during the current 2-hour interval.
OBJECT-TYPE    
  Gauge  

dsRpFrCur2HFpLost 1.3.6.1.4.1.181.2.2.2.10.4.1.9
The number of FPINGs responses received on this VC during the current 2-hour interval.
OBJECT-TYPE    
  Counter  

dsRpFrCur2HFpSent 1.3.6.1.4.1.181.2.2.2.10.4.1.10
The number of FPINGs transmitted on this VC during the current 2-hour interval.
OBJECT-TYPE    
  Counter  

dsRpFrCur2HStatus 1.3.6.1.4.1.181.2.2.2.10.4.1.11
The status summary of this VC during the current 2-hour interval: VALUE DESCRIPTION U VC link is UP D VC link is DOWN B At least one frame had the BECN bit set F At least one frame had the FECN bit set E At least one frame had the DE bit set P The total pipe threshold for utilization was exceeded V The roundtrip threshold for this VC was exceeded
OBJECT-TYPE    
  DisplayString Size(0..7)  

dsRpFrIntvl2HTable 1.3.6.1.4.1.181.2.2.2.10.5
The User 2H Interval Table. This table contains performance information for the past 24 hours, broken down by 2-hour intervals.
OBJECT-TYPE    
  SEQUENCE OF  
    DsRpFrIntvl2HEntry

dsRpFrIntvl2HEntry 1.3.6.1.4.1.181.2.2.2.10.5.1
An entry in the FRIB 2H Interval Table.
OBJECT-TYPE    
  DsRpFrIntvl2HEntry  

dsRpFrIntvl2HDir 1.3.6.1.4.1.181.2.2.2.10.5.1.1
The direction index to the FRIB 2H Interval Table. VALUE DESCRIPTION 1 Transmit 2 Receive
OBJECT-TYPE    
  INTEGER 1..2  

dsRpFrIntvl2HVcIndex 1.3.6.1.4.1.181.2.2.2.10.5.1.2
The VC index to the FRIB 2H Interval Table. The table has 64 entries for indiviual VCs and 1 entry for all other VCs.
OBJECT-TYPE    
  INTEGER 1..65  

dsRpFrIntvl2HNum 1.3.6.1.4.1.181.2.2.2.10.5.1.3
This is the interval number of the FRIB 2H Interval Table. It will be the number of completed 2-hour intervals since the unit has been powered up. After 24 hours, this value remains constant at 12 intervals. 1 is the most recent interval.
OBJECT-TYPE    
  INTEGER 1..12  

dsRpFrIntvl2HVc 1.3.6.1.4.1.181.2.2.2.10.5.1.4
The VC for this entry in the FRIB 2H Interval Table.
OBJECT-TYPE    
  INTEGER 1..8388607  

dsRpFrIntvl2HFrames 1.3.6.1.4.1.181.2.2.2.10.5.1.5
The number of Frame Relay packets transmitted or received during one of the previous 12 2-hour intervals.
OBJECT-TYPE    
  Counter  

dsRpFrIntvl2HOctets 1.3.6.1.4.1.181.2.2.2.10.5.1.6
The number of octets transmitted or received during one of the previous 12 2-hour intervals.
OBJECT-TYPE    
  Counter  

dsRpFrIntvl2HKbps 1.3.6.1.4.1.181.2.2.2.10.5.1.7
The Kilobit/sec rate for data transmitted or received during one of the previous 12 2-hour intervals.
OBJECT-TYPE    
  Gauge  

dsRpFrIntvl2HFpMax 1.3.6.1.4.1.181.2.2.2.10.5.1.8
The maximum FPING roundtrip time (in msec) of all FPINGs on this VC during one of the previous 12 2-hour intervals.
OBJECT-TYPE    
  Counter  

dsRpFrIntvl2HFpAvg 1.3.6.1.4.1.181.2.2.2.10.5.1.9
The average FPING roundtrip time (in msec) of all FPINGs on this VC during one of the previous 12 2-hour intervals.
OBJECT-TYPE    
  Gauge  

dsRpFrIntvl2HFpLost 1.3.6.1.4.1.181.2.2.2.10.5.1.10
The number of FPINGs responses received on this VC during one of the previous 12 2-hour intervals.
OBJECT-TYPE    
  Counter  

dsRpFrIntvl2HFpSent 1.3.6.1.4.1.181.2.2.2.10.5.1.11
The number of FPINGs transmitted on this VC during one of the previous 12 2-hour intervals.
OBJECT-TYPE    
  Counter  

dsRpFrIntvl2HStatus 1.3.6.1.4.1.181.2.2.2.10.5.1.12
The status summary of this VC during the one of the previous 12 2-hour intervals: VALUE DESCRIPTION U VC link is UP D VC link is DOWN B At least one frame had the BECN bit set F At least one frame had the FECN bit set E At least one frame had the DE bit set P The total pipe threshold for utilization was exceeded V The roundtrip threshold for this VC was exceeded
OBJECT-TYPE    
  DisplayString Size(0..7)  

dsRpFrTotalTable 1.3.6.1.4.1.181.2.2.2.10.6
The FRIB Total Table. This table contains performance information for the past 24-hours for Frame Relay data being passed throught the NI Interface. This is a rolling count. When the current 2-hour interval is up, the last entry in the interval table will be removed and the completed 2-hour interval added. At this point the Total Table will be re-calculated.
OBJECT-TYPE    
  SEQUENCE OF  
    DsRpFrTotalEntry

dsRpFrTotalEntry 1.3.6.1.4.1.181.2.2.2.10.6.1
An entry in the FRIB Total Table.
OBJECT-TYPE    
  DsRpFrTotalEntry  

dsRpFrTotalDir 1.3.6.1.4.1.181.2.2.2.10.6.1.1
The direction index to the FRIB Total Table. VALUE DESCRIPTION 1 Transmit 2 Receive
OBJECT-TYPE    
  INTEGER 1..2  

dsRpFrTotalVcIndex 1.3.6.1.4.1.181.2.2.2.10.6.1.2
The VC index to the FRIB Total Table. The table has 64 entries for indiviual VCs and 1 entry for all other VCs.
OBJECT-TYPE    
  INTEGER 1..65  

dsRpFrTotalVc 1.3.6.1.4.1.181.2.2.2.10.6.1.3
The VC for this entry in the FRIB Total Table.
OBJECT-TYPE    
  INTEGER 1..8388607  

dsRpFrTotalFrames 1.3.6.1.4.1.181.2.2.2.10.6.1.4
The number of Frame Relay packets transmitted or received during the past 24 hours.
OBJECT-TYPE    
  Counter  

dsRpFrTotalOctets 1.3.6.1.4.1.181.2.2.2.10.6.1.5
The number of octets transmitted or received during the past 24 hours.
OBJECT-TYPE    
  Counter  

dsRpFrTotalKbps 1.3.6.1.4.1.181.2.2.2.10.6.1.6
The Kilobit/sec rate for data transmitted or received during the past 24 hours.
OBJECT-TYPE    
  Gauge  

dsRpFrTotalFpMax 1.3.6.1.4.1.181.2.2.2.10.6.1.7
The maximum FPING roundtrip time (in msec) of all FPINGs on this VC during the past 24 hours.
OBJECT-TYPE    
  Counter  

dsRpFrTotalFpAvg 1.3.6.1.4.1.181.2.2.2.10.6.1.8
The average FPING roundtrip time (in msec) of all FPINGs on this VC during the past 24 hours.
OBJECT-TYPE    
  Gauge  

dsRpFrTotalFpLost 1.3.6.1.4.1.181.2.2.2.10.6.1.9
The number of FPINGs responses received on this VC during the past 24 hours.
OBJECT-TYPE    
  Counter  

dsRpFrTotalFpSent 1.3.6.1.4.1.181.2.2.2.10.6.1.10
The number of FPINGs transmitted on this VC during the past 24 hours.
OBJECT-TYPE    
  Counter  

dsRpFrTotalStatus 1.3.6.1.4.1.181.2.2.2.10.6.1.11
The status summary of this VC during the past 24 hours: VALUE DESCRIPTION U VC link is UP D VC link is DOWN B At least one frame had the BECN bit set F At least one frame had the FECN bit set E At least one frame had the DE bit set P The total pipe threshold for utilization was exceeded V The roundtrip threshold for this VC was exceeded
OBJECT-TYPE    
  DisplayString Size(0..7)  

dsRpFrDayTable 1.3.6.1.4.1.181.2.2.2.10.7
After the unit has been powered up for 24 hours, the values from the FRIB Total Table are moved into the first slot in the FRIB Day Table. There are seven entries in the FRIB Day Table, so an entire week's history is maintained. The previous day is always in slot 1.
OBJECT-TYPE    
  SEQUENCE OF  
    DsRpFrDayEntry

dsRpFrDayEntry 1.3.6.1.4.1.181.2.2.2.10.7.1
This is an entry in the FRIB Day Table.
OBJECT-TYPE    
  DsRpFrDayEntry  

dsRpFrDayDir 1.3.6.1.4.1.181.2.2.2.10.7.1.1
The direction index to the FRIB Day Table. VALUE DESCRIPTION 1 Transmit 2 Receive
OBJECT-TYPE    
  INTEGER 1..2  

dsRpFrDayVcIndex 1.3.6.1.4.1.181.2.2.2.10.7.1.2
The VC index to the FRIB Day Table. The table has 64 entries for indiviual VCs and 1 entry for all other VCs.
OBJECT-TYPE    
  INTEGER 1..65  

dsRpFrDayNum 1.3.6.1.4.1.181.2.2.2.10.7.1.3
The FRIB Day Table index. The valid values are 1 to 7 days. 1 is the most recent interval.
OBJECT-TYPE    
  INTEGER 1..12  

dsRpFrDayVc 1.3.6.1.4.1.181.2.2.2.10.7.1.4
The VC for this entry in the FRIB Day Table.
OBJECT-TYPE    
  INTEGER 1..8388607  

dsRpFrDayFrames 1.3.6.1.4.1.181.2.2.2.10.7.1.5
The number of Frame Relay packets transmitted or received during one of the previous days.
OBJECT-TYPE    
  Counter  

dsRpFrDayOctets 1.3.6.1.4.1.181.2.2.2.10.7.1.6
The number of octets transmitted or received during one of the previous days.
OBJECT-TYPE    
  Counter  

dsRpFrDayKbps 1.3.6.1.4.1.181.2.2.2.10.7.1.7
The Kilobit/sec rate for data transmitted or received during one of the previous days.
OBJECT-TYPE    
  Gauge  

dsRpFrDayFpMax 1.3.6.1.4.1.181.2.2.2.10.7.1.8
The maximum FPING roundtrip time (in msec) of all FPINGs on this VC during one of the previous days.
OBJECT-TYPE    
  Counter  

dsRpFrDayFpAvg 1.3.6.1.4.1.181.2.2.2.10.7.1.9
The average FPING roundtrip time (in msec) of all FPINGs on this VC during one of the previous days.
OBJECT-TYPE    
  Gauge  

dsRpFrDayFpLost 1.3.6.1.4.1.181.2.2.2.10.7.1.10
The number of FPINGs responses received on this VC during one of the previous days.
OBJECT-TYPE    
  Counter  

dsRpFrDayFpSent 1.3.6.1.4.1.181.2.2.2.10.7.1.11
The number of FPINGs transmitted on this VC during one of the previous days.
OBJECT-TYPE    
  Counter  

dsRpFrDayStatus 1.3.6.1.4.1.181.2.2.2.10.7.1.12
The status summary of this VC during the one of the previous days: VALUE DESCRIPTION U VC link is UP D VC link is DOWN B At least one frame had the BECN bit set F At least one frame had the FECN bit set E At least one frame had the DE bit set P The total pipe threshold for utilization was exceeded V The roundtrip threshold for this VC was exceeded
OBJECT-TYPE    
  DisplayString Size(0..7)  

dsRpFrUrTable 1.3.6.1.4.1.181.2.2.2.10.8
This is a utilization report on non-flag octets that have been transmitted out the network interface for each VC.
OBJECT-TYPE    
  SEQUENCE OF  
    DsRpFrUrEntry

dsRpFrUrEntry 1.3.6.1.4.1.181.2.2.2.10.8.1
This is an entry in the FRIB Ur Table.
OBJECT-TYPE    
  DsRpFrUrEntry  

dsRpFrUrDir 1.3.6.1.4.1.181.2.2.2.10.8.1.1
The direction index to the FRIB Ur Table. Receive is currently not supported and will return a 0 for the Counter values. VALUE DESCRIPTION 1 Transmit 2 Receive
OBJECT-TYPE    
  INTEGER 1..2  

dsRpFrUrVcIndex 1.3.6.1.4.1.181.2.2.2.10.8.1.2
The VC index to the FRIB Ur Table. The table has 64 entries for indiviual VCs
OBJECT-TYPE    
  INTEGER 1..65  

dsRpFrUrVc 1.3.6.1.4.1.181.2.2.2.10.8.1.3
The VC for this entry in the FRIB Ur Table.
OBJECT-TYPE    
  INTEGER 1..8388607  

dsRpFrUrCIRExceeded 1.3.6.1.4.1.181.2.2.2.10.8.1.4
The number of times the CIR threshold was exceeded, but the EIR threshold was not crossed.
OBJECT-TYPE    
  Counter  

dsRpFrUrCIRExceededOctets 1.3.6.1.4.1.181.2.2.2.10.8.1.5
The number of octets that exceeded the CIR threshold, but were less then the EIR threshold.
OBJECT-TYPE    
  Counter  

dsRpFrUrEIRExceeded 1.3.6.1.4.1.181.2.2.2.10.8.1.6
The number of times the EIR threshold was exceeded.
OBJECT-TYPE    
  Counter  

dsRpFrUrEIRExceededOctets 1.3.6.1.4.1.181.2.2.2.10.8.1.7
The number of octets that exceeded the EIR threshold.
OBJECT-TYPE    
  Counter  

dsRpDdsDuration 1.3.6.1.4.1.181.2.2.2.11
.
OBJECT-TYPE    
  TimeTicks  

dsRpDdsTable 1.3.6.1.4.1.181.2.2.2.12
This is the table of DDS statistical data.
OBJECT-TYPE    
  SEQUENCE OF  
    DsRpDdsEntry

dsRpDdsEntry 1.3.6.1.4.1.181.2.2.2.12.1
This is an entry in the DDS Table.
OBJECT-TYPE    
  DsRpDdsEntry  

dsRpDdsIfIndex 1.3.6.1.4.1.181.2.2.2.12.1.1
The index into the table. This is mib-II's ifIndex.
OBJECT-TYPE    
  INTEGER  

dsRpDdsAvailableSecs 1.3.6.1.4.1.181.2.2.2.12.1.2
.
OBJECT-TYPE    
  Counter32  

dsRpDdsTotalSecs 1.3.6.1.4.1.181.2.2.2.12.1.3
.
OBJECT-TYPE    
  Counter32  

dsRpDdsBPVs 1.3.6.1.4.1.181.2.2.2.12.1.4
.
OBJECT-TYPE    
  Counter32  

dsLmLoopback 1.3.6.1.4.1.181.2.2.3.1
This is the type of loopback that is currently active. The values have the following meanings: VALUE DESCRIPTION lmLbkNone(1) No loopback is set lmLbkLine(2) Line loopback is set lmLbkPayload(3) Payload loopback is set lmLbkLocal(4) Local loopback is set lmLbkTiTest(5) TI looback is set lmLbkDp1(6) Data port 1 loopback is set lmLbkDp2(7) Data port 2 loopback is set lmLbkDt1(8) Data terminal loopback on data port 1 is set lmLbkDt2(9) Data terminal loopback on data port 2 is set lmLbkCsu(10) CSU Loopback (DDS) lmLbkDsu(11) DSU Loopback (DDS) lmLbkDpdt(12) Data-Port/Data-Terminal LB
OBJECT-TYPE    
  INTEGER lmLbkNone(1), lmLbkLine(2), lmLbkPayload(3), lmLbkLocal(4), lmLbkTiTest(5), lmLbkDp1(6), lmLbkDp2(7), lmLbkDt1(8), lmLbkDt2(9), lmLbkCsu(10), lmLbkDsu(11), lmLbkDpdt(12)  

dsLmSelfTestState 1.3.6.1.4.1.181.2.2.3.2
This object will start a self test operation when set to lmSelfTestStart(2). At the completion of the test, it will return to its normal state of lmSelfTestIdle(1).
OBJECT-TYPE    
  INTEGER lmSelfTestIdle(1), lmSelfTestStart(2)  

dsLmSelfTestResults 1.3.6.1.4.1.181.2.2.3.3
The results of the last self test operation.
OBJECT-TYPE    
  DisplayString Size(0..255)  

dsRmLbkCode 1.3.6.1.4.1.181.2.2.4.1
The type of remote loopback that is currently set. The possible values are: VALUE DESCRIPTION rmRNone(1) No loopback is set rmRst1(2) A remote loopback reset code is currenlty being sent rmRLine(3) A remote Line loopback is set rmRPayload(4) A remote Payload loopback is set rmRDp1(5) A remote Data Port 1 loopback is set rmRDp2(6) A remote Data Port 2 loopback is set
OBJECT-TYPE    
  INTEGER rmRNone(1), rmRst1(2), rmRLine(3), rmRPayload(4), rmRDp1(5), rmRDp2(6)  

dsRmTestCode 1.3.6.1.4.1.181.2.2.4.2
The type of remote test code that is currently being sent. The possible values are: VALUE DESCRIPTION rmTestNone(1) No test code is being sent rmTestQrs(2) QRS is being sent rmTest324(3) 3-in-24 is being sent rmTestOnes(4) All ones is being sent rmTestZeros(5) All zeros is being sent rmTest511Dp1(6) 511 is being sent out data port 1 rmTest511Dp2(7) 511 is being sent out data port 2 rmTest2047Dp1(8) 2047 is being sent out data port 1 rmTest2047Dp2(9) 2047 is being sent out data port 2 rmTest2toThe23(10) 2 to the 23 is being sent rmTest2toThe15(11) 2 to the 15 is being sent
OBJECT-TYPE    
  INTEGER rmTestNone(1), rmTestQrs(2), rmTest324(3), rmTestOnes(4), rmTestZeros(5), rmTest511Dp1(6), rmTest511Dp2(7), rmTest2047Dp1(8), rmTest2047Dp2(9), rmTest2toThe23(10), rmTest2toThe15(11)  

dsRmBertState 1.3.6.1.4.1.181.2.2.4.3
The current BERT state. The possible values are: VALUE DESCRIPTION rmBertIdle(1) No BERT test is active rmBertOtherStart(2) BERT was started from the control port, front panel, or Telnet rmBertSearching(3) BERT was started from the agent and has not yet detected the code rmBertFound(4) BERT was started from the agent and has detected the code
OBJECT-TYPE    
  INTEGER rmBertIdle(1), rmBertOtherStart(2), rmBertSearching(3), rmBertFound(4)  

dsRmBertCode 1.3.6.1.4.1.181.2.2.4.4
This object controls the activation of BERT tests. The possible values are: VALUE DESCRIPTION rmBertNone(1) No BERT test is active rmBertQrs(2) BERT for QRS rmBert324(3) BERT for 3-in-24 rmBertOnes(4) BERT for all ones rmBertZeros(5) BERT for all zeros rmBert511Dp1(6) BERT for 511 on data port 1 rmBert511Dp2(7) BERT for 511 on data port 2 rmBert2047Dp1(8) BERT for 2047 on data port 1 rmBert2047Dp2(9) BERT for 2047 on data port 2 rmTest2toThe23(10) BERT for 2 to the 23 rmTest2toThe15(11) BERT for 2 to the 15
OBJECT-TYPE    
  INTEGER rmBertNone(1), rmBertQrs(2), rmBert324(3), rmBertOnes(4), rmBertZeros(5), rmBert511Dp1(6), rmBert511Dp2(7), rmBert2047Dp1(8), rmBert2047Dp2(9), rmTest2toThe23(10), rmTest2toThe15(11)  

dsRmBertTestSecs 1.3.6.1.4.1.181.2.2.4.5
The number of seconds the requested test code has been detected since the start of the BERT.
OBJECT-TYPE    
  INTEGER 0..2147483647  

dsRmBertBitErrors 1.3.6.1.4.1.181.2.2.4.6
The number of bit errors detected since the start of the BERT.
OBJECT-TYPE    
  INTEGER 0..2147483647  

dsRmBertErrdSecs 1.3.6.1.4.1.181.2.2.4.7
The number of errored seconds detected since the start of the BERT.
OBJECT-TYPE    
  INTEGER 0..2147483647  

dsRmBertTotalErrors 1.3.6.1.4.1.181.2.2.4.8
The number of total errors detected since the start of the BERT.
OBJECT-TYPE    
  INTEGER 0..2147483647  

dsRmBertReSync 1.3.6.1.4.1.181.2.2.4.9
The number of times BERT has lost and re-aquired the pattern.
OBJECT-TYPE    
  INTEGER 0..2147483647  

dsRmFping 1.3.6.1.4.1.181.2.2.4.10
OBJECT IDENTIFIER    

dsRmFpingAction 1.3.6.1.4.1.181.2.2.4.10.1
The control actions for the FPING test. Possible values are: VALUE DESCRIPTION rmFpingStart(1) Start sending FPINGs rmFpingStop(2) Stop sending FPINGs
OBJECT-TYPE    
  INTEGER rmFpingStart(1), rmFpingStop(2)  

dsRmFpingState 1.3.6.1.4.1.181.2.2.4.10.2
The current state of the FPING tester. Possible values are: VALUE DESCRIPTION rmFpingIdle(1) No FPINGs are being generated rmFpingOtherStart(2) FPINGs are being generated. The test was started via one of the other management interfaces. rmFpingRunning(3) FPINGs are being generated. The test was started via SNMP.
OBJECT-TYPE    
  INTEGER rmFpingIdle(1), rmFpingOtherStart(2), rmFpingRunning(3)  

dsRmFpingVc 1.3.6.1.4.1.181.2.2.4.10.3
The VC that FPINGs will be sent on. VC values range from (0..1023) if the Frame Relay address length is 2 octets and (0..8388607) if the address length is 4 octets. Default is 500.
OBJECT-TYPE    
  INTEGER 0..8388607  

dsRmFpingFreq 1.3.6.1.4.1.181.2.2.4.10.4
The frequency (in seconds) that FPING packets will be transmitted. The range is (5..255). Default is 5.
OBJECT-TYPE    
  INTEGER 5..255  

dsRmFpingLen 1.3.6.1.4.1.181.2.2.4.10.5
The length (in octets) of the payload portion of the FPING packets. The range is (0..1400). Default is 0.
OBJECT-TYPE    
  INTEGER 0..1400  

dsRmFpingCur 1.3.6.1.4.1.181.2.2.4.10.6
The roundtrip time (in msec) of the last FPING sent.
OBJECT-TYPE    
  INTEGER 0..2000  

dsRmFpingMin 1.3.6.1.4.1.181.2.2.4.10.7
The minimum roundtrip time (in msec) of all FPINGs sent during this test.
OBJECT-TYPE    
  INTEGER 0..2000  

dsRmFpingMax 1.3.6.1.4.1.181.2.2.4.10.8
The maximum roundtrip time (in msec) of all FPINGs sent during this test.
OBJECT-TYPE    
  INTEGER 0..2000  

dsRmFpingAvg 1.3.6.1.4.1.181.2.2.4.10.9
The average roundtrip time (in msec) of all FPINGs sent during this test.
OBJECT-TYPE    
  INTEGER 0..2000  

dsRmFpingLost 1.3.6.1.4.1.181.2.2.4.10.10
The number of FPING packets lost during this test.
OBJECT-TYPE    
  INTEGER 0..65535  

dsRmFpingTotal 1.3.6.1.4.1.181.2.2.4.10.11
The total number of FPING packets transmitted during this test.
OBJECT-TYPE    
  INTEGER 0..65535  

dsRmFpingRmtVc 1.3.6.1.4.1.181.2.2.4.10.12
The VC used at the remote end of the circuit.
OBJECT-TYPE    
  DisplayString Size(0..8)  

dsRmFpingRmtIp 1.3.6.1.4.1.181.2.2.4.10.13
The IP address of the unit responding to FPINGs.
OBJECT-TYPE    
  IpAddress  

dsRmInsertBitError 1.3.6.1.4.1.181.2.2.4.11
Possible values are: VALUE DESCRIPTION insertBitError(1) Start sending FPINGs noInsertBitError(2) Stop sending FPINGs
OBJECT-TYPE    
  INTEGER insertBitError(1), noInsertBitError(2)  

dsAcAlmMsg 1.3.6.1.4.1.181.2.2.5.1
This object controls the displaying/sending of alarm messages. Alarm messages will be sent in the format determined by dsAcAlmFormat if dsAcAlmMsg is set to acAlmMsgEnable(1). Alarm messages will not be sent if this object is set to acAlmMsgDisable(2).
OBJECT-TYPE    
  INTEGER acAlmMsgEnable(1), acAlmMsgDisable(2)  

dsAcYelAlm 1.3.6.1.4.1.181.2.2.5.2
This object determines if incoming Yellow Alarm will cause an alarm message to be sent. Setting this object to acYelAlmEnable(1) causes an alarm to be sent when Yellow Alarm is received on the Network or Terminal Interface. Setting this object to acYelAlmDisable(2) will not send an alarm when Yellow Alarm is received.
OBJECT-TYPE    
  INTEGER acYelAlmEnable(1), acYelAlmDisable(2)  

dsAcDeact 1.3.6.1.4.1.181.2.2.5.3
This object controls the number of seconds an alarm condition must remain clear before the unit declares it cleared. The range is from 0 to 15 seconds.
OBJECT-TYPE    
  INTEGER 1..15  

dsAcEst 1.3.6.1.4.1.181.2.2.5.4
This object determines the threshold of errored seconds that triggers an Excessive Error Rate (EER) alarm. Setting this object to zero disables errored seconds causing an EER alarm.
OBJECT-TYPE    
  INTEGER 0..900  

dsAcUst 1.3.6.1.4.1.181.2.2.5.5
This object determines the threshold of uavailable seconds that triggers an Excessive Error Rate (EER) alarm. Setting this object to zero disables unavailable seconds causing an EER alarm.
OBJECT-TYPE    
  INTEGER 0..900  

dsAcSt 1.3.6.1.4.1.181.2.2.5.6
This object determines the window used to calculate whether an Excessive Error Rate (EER) alarm should be generated from errored seconds or unavailable seconds. Setting this object to acSt15(1) establishes a 15-minute sliding window. Setting this object to acSt60(2) establishes a 60-minute sliding window.
OBJECT-TYPE    
  INTEGER acSt15(1), acSt60(2)  

dsAcBerAlm 1.3.6.1.4.1.181.2.2.5.7
This object controls the sending of a Bit Error Rate (BER) alarm. The possible values are: VALUE DESCRIPTION acBerAlmEnable(1) Enable sending BER alarms acBerAlmDisable(2) Disable sending BER alarms
OBJECT-TYPE    
  INTEGER acBerAlmEnable(1), acBerAlmDisable(2)  

dsAcRfaAlm 1.3.6.1.4.1.181.2.2.5.8
This object controls the sending of a Remote Frame Alarm (RFA). The possible values are: VALUE DESCRIPTION acRfaAlmEnable(1) Enable sending RFA alarms acRfaAlmDisable(2) Disable sending RFA alarms
OBJECT-TYPE    
  INTEGER acRfaAlmEnable(1), acRfaAlmDisable(2)  

dsAcAisAlm 1.3.6.1.4.1.181.2.2.5.9
This object controls the sending of Alarm Indication Signal (AIS) alarms. The possible values are: VALUE DESCRIPTION acAisAlmEnable(1) Enable sending AIS alarms acAisAlmDisable(2) Disable sending AIS alarms
OBJECT-TYPE    
  INTEGER acAisAlmEnable(1), acAisAlmDisable(2)  

dsCcEcho 1.3.6.1.4.1.181.2.2.6.1
This object controls character echo on the control port. The possible values are: VALUE DESCRIPTION ccEchoEnable(1) Enable control port echo ccEchoDisable(2) Disable control port echo
OBJECT-TYPE    
  INTEGER ccEchoEnable(1), ccEchoDisable(2)  

dsCcControlPort 1.3.6.1.4.1.181.2.2.6.2
This object determines whether the control port is the DCE or DTE port. The possible values are: VALUE DESCRIPTION ccDce(1) The control port is the DCE port ccDte(2) The control port is the DTE port
OBJECT-TYPE    
  INTEGER ccDce(1), ccDte(2)  

dsCcBaud 1.3.6.1.4.1.181.2.2.6.3
The baud rate of the control port. The possible values are: VALUE DESCRIPTION cc2400(1) 2400 baud cc9600(2) 9600 baud cc19200(3) 19200 baud cc38400(4) 38400 baud
OBJECT-TYPE    
  INTEGER cc2400(1), cc9600(2), cc19200(3), cc38400(4)  

dsCcParity 1.3.6.1.4.1.181.2.2.6.4
The parity of the control port. The possible values are: VALUE DESCRIPTION ccNone(1) No parity ccEven(2) Even parity ccOdd(3) Odd parity
OBJECT-TYPE    
  INTEGER ccNone(1), ccEven(2), ccOdd(3)  

dsCcDataBits 1.3.6.1.4.1.181.2.2.6.5
The number of data bits for the control port. The possible values are: VALUES DESCRIPTION cc7Bit(1) 7 data bits cc8Bit(2) 8 data bits
OBJECT-TYPE    
  INTEGER cc7Bit(1), cc8Bit(2)  

dsCcStopBits 1.3.6.1.4.1.181.2.2.6.6
The number of stop bits for the control port. The possible values are: VALUE DESCRIPTION cc1Bit(1) 1 stop bit cc2Bit(2) 2 stop bits
OBJECT-TYPE    
  INTEGER cc1Bit(1), cc2Bit(2)  

dsCcDceIn 1.3.6.1.4.1.181.2.2.6.7
The input status of the DCE signals RTS and DTR. The possible valuesa re: VALUE DESCRIPTION ccBothOff(1) RTS off, DTR off ccRtsOnDtrOff(2) RTS on, DTR off ccRtsOffDtrOn(3) RTS off, DTR on ccBothOn(4) RTS on, DTR on
OBJECT-TYPE    
  INTEGER ccBothOff(1), ccRtsOnDtrOff(2), ccRtsOffDtrOn(3), ccBothOn(4)  

dsCcDteIn 1.3.6.1.4.1.181.2.2.6.8
The input status of the DTE signals CTS and DCD. The possible values are: VALUE DESCRIPTION ccBothOff(1) CTS off, DCD off ccCtsOnDcdOff(2) CTS on, DCD off ccCTSoffDCDon(3) CTS off, DCD on ccBothOn(4) CTS on, DCD on
OBJECT-TYPE    
  INTEGER ccBothOff(1), ccCtsOnDcdOff(2), ccCtsOffDcdOn(3), ccBothOn(4)  

dsDcTable 1.3.6.1.4.1.181.2.2.7.1
The Data Port Configuration Table. This table contains information on the configuration of each of the unit's data ports.
OBJECT-TYPE    
  SEQUENCE OF  
    DsDcEntry

dsDcEntry 1.3.6.1.4.1.181.2.2.7.1.1
An entry in the Data Port Configuration Table.
OBJECT-TYPE    
  DsDcEntry  

dsDcIndex 1.3.6.1.4.1.181.2.2.7.1.1.1
The index to the Data Port Configuration Table. The possible values are 1 through 2.
OBJECT-TYPE    
  INTEGER 1..2  

dsDcDataInvert 1.3.6.1.4.1.181.2.2.7.1.1.2
The data inversion of the data port. The possible values are: VALUE DESCRIPTION dcDataInvertEnable(1) Invert the data port signal dcDataInvertDisable(2) Don't invert the data port signal
OBJECT-TYPE    
  INTEGER dcDataInvertEnable(1), dcDataInvertDisable(2)  

dsDcInterface 1.3.6.1.4.1.181.2.2.7.1.1.3
The type of electrical interface the data port is using. The possible values are: VALUE DESCRIPTION dcV35Interface(1) V.35 dcEia530Interface(2) EIA-530 dcV35DSInterface (3) V.35 DataSMART Compatible
OBJECT-TYPE    
  INTEGER dcV35Interface(1), dcEia530Interface(2), dcV35DSInterface(3)  

dsDcClockSource 1.3.6.1.4.1.181.2.2.7.1.1.4
The clock source for the data port. The possible values are: VALUE DESCRIPTION dcInternalClock(1) Use the internal clock dcExternalClock(2) Use the external clock
OBJECT-TYPE    
  INTEGER dcInternalClock(1), dcExternalClock(2)  

dsDcXmtClkInvert 1.3.6.1.4.1.181.2.2.7.1.1.5
The inversion status of the transmit clock signal for the data port. The possible values are: VALUE DESCRIPTION dcXClkInvertEnable(1) Invert the transmit clock signal dcXClkInvertDisable(2) Don't invert the transmit clock signal
OBJECT-TYPE    
  INTEGER dcXClkInvertEnable(1), dcXClkInvertDisable(2)  

dsDcRcvClkInvert 1.3.6.1.4.1.181.2.2.7.1.1.6
The inversion status of the received clock signal for the data port. The possible values are: VALUE DESCRIPTION dcRClkInvertEnable(1) Invert the received clock signal dcRClkInvertDisable(2) Don't invert the received clock signal
OBJECT-TYPE    
  INTEGER dcRClkInvertEnable(1), dcRClkInvertDisable(2)  

dsDcIdleChar 1.3.6.1.4.1.181.2.2.7.1.1.7
The idle character to use for the data port. The possible values are: VALUE DESCRIPTION dc7eIdleChar(1) The idle character is hex 7E dc7fIdleChar(1) The idle character is hex 7F dcffIdleChar(3) The idle character is hex FF
OBJECT-TYPE    
  INTEGER dc7eIdleChar(1), dc7fIdleChar(2), dcffIdleChar(3)  

dsDcLOSInput 1.3.6.1.4.1.181.2.2.7.1.1.8
The combination of RTS and DTR that will cause a data port Loss of Signal alarm. The possible values are: VALUE DESCRIPTION dcLosNone(1) Data port LOS is disabled dcLosRts(2) LOS is declared when RTS is lost dcLosDtr(3) LOS is declared when DTR is lost dcLosBoth(4) LOS is declared when both RTS and DTR are lost.
OBJECT-TYPE    
  INTEGER dcLosNone(1), dcLosRTS(2), dcLosDTR(3), dcLosBoth(4)  

dsFcLoadXcute 1.3.6.1.4.1.181.2.2.8.1
The Fractional Table that is active. The possible values are: VALUE DESCRIPTION fcLoadXcuteIdle(1) The normal state fcLoadXcuteStartA(2) Load and execute table A fcLoadXcuteStartB(3) Load and execute table B
OBJECT-TYPE    
  INTEGER fcLoadXcuteIdle(1), fcLoadXcuteStartA(2), fcLoadXcuteStartB(3)  

dsFcTable 1.3.6.1.4.1.181.2.2.8.2
This is the DS1/E1 Fractional Table. This table consists of configuration information about DS1/E1 fractional services.
OBJECT-TYPE    
  SEQUENCE OF  
    DsFcEntry

dsFcEntry 1.3.6.1.4.1.181.2.2.8.2.1
This is an entry in the Fractional Table.
OBJECT-TYPE    
  DsFcEntry  

dsFcTableIndex 1.3.6.1.4.1.181.2.2.8.2.1.1
This is the index into the Fractional Table. The possible values are: VALUE DESCRIPTION 1 Stored configuration A 2 Stored configuration B 3 Currently executing fractional table
OBJECT-TYPE    
  INTEGER 1..3  

dsFcChanIndex 1.3.6.1.4.1.181.2.2.8.2.1.2
This is the index of the fractional channel. DS1 has 24 channels and E1 has 32.
OBJECT-TYPE    
  INTEGER 1..31  

dsFcChanMap 1.3.6.1.4.1.181.2.2.8.2.1.3
The destination and data rate of the channel. The possible values are: VALUE DESCRIPTION fcChanIdle(1) The channel is idle fcChanTiData(2) The channel carries data and is mapped to a TI channel fcChanTiVoice(3) The channel carries voice and is mapped to a TI channel fcChan56Dp1(4) The cahnnel is set for 56K and is mapped to data port 1 fcChan64Dp1(5) The channel is set for 64K and is mapped to data port 1 fcChan56Dp2(6) The channel is set for 56K and is mapped to data port 2 fcChan64Dp2(7) The channel is set for 64K and is mapped to data port 2 fcChanDLNK(8) The channel is idle and set for data link communications fcChanDPDL(9) The channel is active and also set for data link communications fCchanUanv(10) The channel is unavailable
OBJECT-TYPE    
  INTEGER fcChanIdle(1), fcChanTiData(2), fcChanTiVoice(3), fcChan56Dp1(4), fcChan64Dp1(5), fcChan56Dp2(6), fcChan64Dp2(7), fcChanDLNK(8), fcChanDPDL(9), fcChanUnav(10)  

dsFcMap16 1.3.6.1.4.1.181.2.2.8.3
This object determines if channel 16 is available for user payload data. This is only possible if the unit is configured for Common Channel Signalling. The possible values are: VALUE DESCRIPTION fcMap16Used(1) Channel 16 cannot be used for user payload data fcMap16Unused(2) Channel 16 is available for user payload data
OBJECT-TYPE    
  INTEGER fcMap16Used(1), fcMap16Unused(2)  

dsFmcFrameType 1.3.6.1.4.1.181.2.2.9.1
The frame type for packets being transmitted and received for IP connectivity. The possible values are: VALUE DESCRIPTION fmcFrNlpid(1) Frame Relay NLPID encapsulation fmcFrEther(2) Frame Relay Ethertype encapsulation fmcAtmNlpid(3) ATM DXI NLPID encapsulation fmcAtmLlcSnap(4) ATM DXI LLC/SNAP encapsulation fmcAtmVcMux(5) ATM DXI VC-based multiplexing
OBJECT-TYPE    
  INTEGER fmcFrNlpid(1), fmcFrEther(2), fmcAtmNlpid(3), fmcAtmLlcSnap(4), fmcAtmVcMux(5)  

dsFmcAddrOctets 1.3.6.1.4.1.181.2.2.9.2
The length in octets of the Frame Relay address. The possible values are: VALUE DESCRIPTION fmc2Octets(1) The address is 2 octets long fmc4Octets(1) The address is 4 octets long
OBJECT-TYPE    
  INTEGER fmcTwoOctets(1), fmcFourOctets(2)  

dsFmcFcsBits 1.3.6.1.4.1.181.2.2.9.3
The length in bits of the Frame Relay FCS. The possible values are: VALUE DESCRIPTION fmc16Bits(1) The FCS field is 16 bits long fmc32Bits(2) The FCS field is 32 bits long
OBJECT-TYPE    
  INTEGER fmc16Bits(1), fmc32Bits(2)  

dsFmcUpperBW 1.3.6.1.4.1.181.2.2.9.4
The percent of bandwidth utilization threshold. If the threshold is exceeded, an event will be recorded in the performance data and a trap (if configured) will be sent. Valid values are 5-95 in increments of 5.
OBJECT-TYPE    
  INTEGER 5..95  

dsFmcFpingOper 1.3.6.1.4.1.181.2.2.9.5
The enabling and disabling of FPING operation. Valid values are Enable and Disable.
OBJECT-TYPE    
  INTEGER fmcFpoEnable(1), fmcFpoDisable(2)  

dsFmcFpingGen 1.3.6.1.4.1.181.2.2.9.6
The number of distinct VC to be received on the NI before FPINGs are automatically sent out.
OBJECT-TYPE    
  INTEGER 0..64  

dsFmcFpingThres 1.3.6.1.4.1.181.2.2.9.7
The maximum roundtrip time of a FPING packet in milliseconds. If the threshold is exceeded, an event will be recorded in the performance data and a trap (if configured) will be sent. Valid values are 20-2000 in increments of 10.
OBJECT-TYPE    
  INTEGER 20..2000  

dsFmcFpingRst 1.3.6.1.4.1.181.2.2.9.8
Reset the specified VC to an initial state where FPING connectivity is check for. Valid values are 0-1023 for a 2 octet address field and 0-8388607 for a 4 octet address field.
OBJECT-TYPE    
  INTEGER 0..8388607  

dsFmcAddVc 1.3.6.1.4.1.181.2.2.9.9
Add a VC to the list of monitored VCs
OBJECT-TYPE    
  INTEGER 0..8388607  

dsFmcDelVc 1.3.6.1.4.1.181.2.2.9.10
Del a VC from the list of monitored VCs. Any statistics related to this VC will be moved to the 'other' category.
OBJECT-TYPE    
  INTEGER 0..8388607  

dsMcNetif 1.3.6.1.4.1.181.2.2.10.1
The management access port(s) for Telnet and SNMP. The possible values are: VALUE DESCRIPTION mcNetNone(1) No ip interface paths are active mcNetEthernet(2) The ethernet ip interface is active mcNetPppSlip(3) The ppp/slip (control ports) ip interfaces are active mcNetSlip(4) The slip (control ports) ip interface is active mcNetDatalink(5) The data link ip interface is active mcNetES(6) The ethernet and slip (control ports) ip interfaces are active mcNetED(7) The ethernet and data link ip interfaces are active mcNetESD(8) The ethernet, slip (control ports), and data link ip interfaces are active mcNetPSD(9) The ppp/slip (control ports) and data link ip interfaces are active mcNetSD(10) The slip (control ports) and data link ip interfaces are active mcNetInband(11) The inband Frame Relay (NI and Data Port) ip interface is active
OBJECT-TYPE    
  INTEGER mcNetNone(1), mcNetEthernet(2), mcNetPppSlip(3), mcNetSlip(4), mcNetDatalink(5), mcNetES(6), mcNetED(7), mcNetESD(8), mcNetPSD(9), mcNetSD(10), mcNetInband(11)  

dsMcT1DLPath 1.3.6.1.4.1.181.2.2.10.2
The T1 DataLink value. This configuration is used if the NETIF has a DataLink component. The possible values are: VALUE DESCRIPTION mcDLPathFdl(1) The DataLink will use the FDL. mcDLPathTSn-64 The DataLink will use TSn. If TSn is IDLE, the data rate will be set to 64K. If TSn is assigned to a Data Port, the DataLink will use 8K of TSn. mcDLPathTSn-56 The DataLink will use TSn. If TSn is IDLE, the data rate will be set to 56K. If TSn is assigned to a Data Port, the DataLink will use 8K of TSn.
OBJECT-TYPE    
  INTEGER mcDLPathFdl(1), mcDLPathTS1-64(2), mcDLPathTS2-64(3), mcDLPathTS3-64(4), mcDLPathTS4-64(5), mcDLPathTS5-64(6), mcDLPathTS6-64(7), mcDLPathTS7-64(8), mcDLPathTS8-64(9), mcDLPathTS9-64(10), mcDLPathTS10-64(11), mcDLPathTS11-64(12), mcDLPathTS12-64(13), mcDLPathTS13-64(14), mcDLPathTS14-64(15), mcDLPathTS15-64(16), mcDLPathTS16-64(17), mcDLPathTS17-64(18), mcDLPathTS18-64(19), mcDLPathTS19-64(20), mcDLPathTS20-64(21), mcDLPathTS21-64(22), mcDLPathTS22-64(23), mcDLPathTS23-64(24), mcDLPathTS24-64(25), mcDLPathTS1-56(26), mcDLPathTS2-56(27), mcDLPathTS3-56(28), mcDLPathTS4-56(29), mcDLPathTS5-56(30), mcDLPathTS6-56(31), mcDLPathTS7-56(32), mcDLPathTS8-56(33), mcDLPathTS9-56(34), mcDLPathTS10-56(35), mcDLPathTS11-56(36), mcDLPathTS12-56(37), mcDLPathTS13-56(38), mcDLPathTS14-56(39), mcDLPathTS15-56(40), mcDLPathTS16-56(41), mcDLPathTS17-56(42), mcDLPathTS18-56(43), mcDLPathTS19-56(44), mcDLPathTS20-56(45), mcDLPathTS21-56(46), mcDLPathTS22-56(47), mcDLPathTS23-56(48), mcDLPathTS24-56(49)  

dsMcDefRoute 1.3.6.1.4.1.181.2.2.10.3
The unit's default IP router.
OBJECT-TYPE    
  IpAddress  

dsMcCIpAddr 1.3.6.1.4.1.181.2.2.10.4
The IP address for the unit's Control Port.
OBJECT-TYPE    
  IpAddress  

dsMcDIpAddr 1.3.6.1.4.1.181.2.2.10.5
The IP address for the unit's Data Link.
OBJECT-TYPE    
  IpAddress  

dsMcCDIpMask 1.3.6.1.4.1.181.2.2.10.6
The IP subnet mask for the unit's Control Port and Data Link.
OBJECT-TYPE    
  IpAddress  

dsMcEIpAddr 1.3.6.1.4.1.181.2.2.10.7
The IP address for the unit's Ethernet Port.
OBJECT-TYPE    
  IpAddress  

dsMcEIpMask 1.3.6.1.4.1.181.2.2.10.8
The IP subnet mask for the unit's Ethernet Port.
OBJECT-TYPE    
  IpAddress  

dsMcIIpAddr 1.3.6.1.4.1.181.2.2.10.9
The IP address for the unit's In-Band Interface.
OBJECT-TYPE    
  IpAddress  

dsMcIIpMask 1.3.6.1.4.1.181.2.2.10.10
The IP subnet mask for the unit's In-Band Interface.
OBJECT-TYPE    
  IpAddress  

dsAmc 1.3.6.1.4.1.181.2.2.10.11
OBJECT IDENTIFIER    

dsAmcAgent 1.3.6.1.4.1.181.2.2.10.11.1
The operational status of the SMMP agent. The possible values are: VALUE DESCRIPTION. amcEnabled(1) The SNMP agent is enabled amcDisabled(2) The SNMP agent is disabled.
OBJECT-TYPE    
  INTEGER amcEnabled(1), amcDisabled(2)  

dsAmcSourceScreen 1.3.6.1.4.1.181.2.2.10.11.2
The status of the IP source address screening security. The possible values are: VALUE DESCRIPTION mcIpScreen(1) The screening security is enabled mcNoScreen(2) The screening security is disabled
OBJECT-TYPE    
  INTEGER mcIpScreen(1), mcNoScreen(2)  

dsAmcTrapTable 1.3.6.1.4.1.181.2.2.10.11.3
The SNMP Trap Table. This table lists the different types of traps and allows each type to be individually enabled/disabled. Currently, the types of traps are: Start Traps - Cold-Start and Warm-Start Link Traps - Link-Up and Link-Down Traps Authentication Traps - e.g. incorrect Telnet password Enterprise Traps - e.g. NI EER Trap
OBJECT-TYPE    
  SEQUENCE OF  
    DsAmcTrapEntry

dsAmcTrapEntry 1.3.6.1.4.1.181.2.2.10.11.3.1
An entry in the SNMP Trap Table.
OBJECT-TYPE    
  DsAmcTrapEntry  

dsAmcTrapType 1.3.6.1.4.1.181.2.2.10.11.3.1.1
The type of trap. There is one row in dsAmcTrapTable for each type of trap. The possible values are: VALUE DESCRIPTION amcStartTraps(1) Cold-Start and Warm-Start Traps. amcLinkTraps(2) Link-Up and Link-Down Traps. amcAuthenTraps(3) Authentication Traps. Sent for: - Incorrect Telnet password - Source IP address not on IP Screen List - Incorrect SNMP Read Community String - Incorrect SNMP Write Community String amcEnterpriseTraps(4) Enterprise-Specific Traps.
OBJECT-TYPE    
  INTEGER mcStartTraps(1), mcLinkTraps(2), mcAuthenTraps(3), mcEnterpriseTraps(4)  

dsAmcTrapStatus 1.3.6.1.4.1.181.2.2.10.11.3.1.2
Indicates whether the particular type of trap is enabled or disabled. The possible values are: VALUE DESCRIPTION amcEnabled(1) These types of traps are enabled. amcDisabled(2) These types of traps are disabled.
OBJECT-TYPE    
  INTEGER amcEnabled(1), amcDisabled(2)  

dsAmcScrnTable 1.3.6.1.4.1.181.2.2.10.11.4
The Source Address Screening Table. The entries in this table are the IP addresses which are allowed to access this unit.
OBJECT-TYPE    
  SEQUENCE OF  
    DsAmcScrnEntry

dsAmcScrnEntry 1.3.6.1.4.1.181.2.2.10.11.4.1
An entry in the Source Address Screening Table.
OBJECT-TYPE    
  DsAmcScrnEntry  

dsAmcScrnIndex 1.3.6.1.4.1.181.2.2.10.11.4.1.1
The index to the Source Address Screening Table. Ten entries are possible.
OBJECT-TYPE    
  INTEGER 1..10  

dsAmcScrnIpAddr 1.3.6.1.4.1.181.2.2.10.11.4.1.2
An IP Address(es) which will be permitted to access this unit. This object is combined with dsAmcScrnIpMask to allow a single entry to permit access by an entire subnet.
OBJECT-TYPE    
  IpAddress  

dsAmcScrnIpMask 1.3.6.1.4.1.181.2.2.10.11.4.1.3
An IP subnet mask that indicates which portion of dsAmcScrnIpAddr must be matched to permit access. This allows a single entry to provide access by an entire IP subnet. A mask of '255.255.255.0' means that hosts on the subnet of dsAmcScrnIpAddr are permitted access. A mask of '255.255.255.255' means that only the IP address which exactly matches dsAmcScrnIpAddr is permitted access (i.e. only a single host).
OBJECT-TYPE    
  IpAddress  

dsAmcTrapDestTable 1.3.6.1.4.1.181.2.2.10.11.5
The SNMP Trap Destinations Table. This table lists up to 10 addresses to send SNMP traps to when alarm conditions occur.
OBJECT-TYPE    
  SEQUENCE OF  
    DsAmcTrapDestEntry

dsAmcTrapDestEntry 1.3.6.1.4.1.181.2.2.10.11.5.1
An entry in the SNMP Trap Destinations Table.
OBJECT-TYPE    
  DsAmcTrapDestEntry  

dsAmcTrapDestIndex 1.3.6.1.4.1.181.2.2.10.11.5.1.1
The index to the SNMP Trap Destinations Table.
OBJECT-TYPE    
  INTEGER 1..10  

dsAmcTrapDestIpAddr 1.3.6.1.4.1.181.2.2.10.11.5.1.2
The IP address portion of a Trap Destination Entry, used when sending SNMP traps.
OBJECT-TYPE    
  IpAddress  

dsAmcTrapDestVc 1.3.6.1.4.1.181.2.2.10.11.5.1.3
The VC portion of a Trap Destination Entry, used when sending SNMP traps.
OBJECT-TYPE    
  INTEGER 0..8388607  

dsAmcTrapDestPort 1.3.6.1.4.1.181.2.2.10.11.5.1.4
The Port portion of a Trap Destination Entry, used when sending SNMP traps.
OBJECT-TYPE    
  INTEGER amcNIPort(1), amcDPPort(2)  

dsMcIVc 1.3.6.1.4.1.181.2.2.10.12
fill in later.
OBJECT-TYPE    
  DLCI  

dsMcIPort 1.3.6.1.4.1.181.2.2.10.13
fill in later The possible values are: VALUE DESCRIPTION amcNiPort(1) Communicate over NI amcDPPort(2) communicate over DP
OBJECT-TYPE    
  INTEGER amcNiPort(1), amcDPPort(2)  

dsNcFraming 1.3.6.1.4.1.181.2.2.11.1
The type of framing being used on the Network Interface. The possible values are: VALUE DESCRIPTION ncSF(1) SF (D4) framing ncESF(2) ESF framing ncEricsson(3) Ericsson framing
OBJECT-TYPE    
  INTEGER ncSF(1), ncESF(2), ncEricsson(3)  

dsNcCoding 1.3.6.1.4.1.181.2.2.11.2
The type of line coding being used on the Network Interface. The possible values are: VALUE DESCRIPTION ncAmi(1) AMI line coding ncB8zs(2) B8ZS line coding.
OBJECT-TYPE    
  INTEGER ncAmi(1), ncB8zs(2)  

dsNcT1403 1.3.6.1.4.1.181.2.2.11.3
This object enables/disables the sending of T1.403 PRM messages. The possible values are: VALUE DESCRIPTION ncT1403Enable(1) Enable T1.403 messages ncT1403Disable(2) Disabled T1.403 messages
OBJECT-TYPE    
  INTEGER ncT1403Enable(1), ncT1403Disable(2)  

dsNcYellow 1.3.6.1.4.1.181.2.2.11.4
This object enables/disables sending Yellow alarm out the Network Interface upon receipt of an alarm on the Network Interface. The possible values are: VALUE DESCRIPTION ncYelEnable(1) Enable sending Yellow alarm ncYelDisable(1) Disable sending Yellow alarm
OBJECT-TYPE    
  INTEGER ncYelEnable(1), ncYelDisable(2)  

dsNcAddr54 1.3.6.1.4.1.181.2.2.11.5
If 54016 addressing is enabled, this object determines what type of addressing the unit responds to. The possible values are: VALUE DESCRIPTION ncAddrCsu(1) CSU addressing mode ncAddrDsu(2) DSU addressing mode ncAddrBoth(3) Both CSU and DSU addressing modes
OBJECT-TYPE    
  INTEGER ncAddrCsu(1), ncAddrDsu(2), ncAddrBoth(3)  

dsNc54016 1.3.6.1.4.1.181.2.2.11.6
This object determines whether the unit responds to 54016 addressing modes. The possible values are: VALUE DESCRIPTION nc54016Enable(1) Enabled 54016 addressing nc54016Disable(2) Disable 54016 addressing
OBJECT-TYPE    
  INTEGER nc54016Enable(1), nc54016Disable(2)  

dsNcLbo 1.3.6.1.4.1.181.2.2.11.7
The Network Interface Line Build Out setting. The possible values are: VALUE DESCRIPTION ncLbo0(1) 0.0dB line attenuation ncLbo1(2) 7.5dB line attenuation ncLbo2(3) 15.0 dB line attenuation
OBJECT-TYPE    
  INTEGER ncLbo0(1), ncLbo1(2), ncLbo2(3)  

dsNcMF16 1.3.6.1.4.1.181.2.2.11.8
The E1 network interface Time Slot 16 MultiFrame alignment signal setting. The possible values are: VALUE DESCRIPTION ncMF16Enable(1) Enable the Time Slot 16 MultiFrame alignment signal ncMF16Disable(2) Disabled the Time Slot 16 MultiFrame alignment signal
OBJECT-TYPE    
  INTEGER ncMF16Enable(1), ncMF16Disable(2)  

dsNcCRC 1.3.6.1.4.1.181.2.2.11.9
The E1 network interface CRC generation/checking setting. The possible values are: VALUE DESCRIPTION ncCrcEnable(1) Enable CRC generation/checking ncCrcDisable(2) Disable CRC generation/checking
OBJECT-TYPE    
  INTEGER ncCrcEnable(1), ncCrcDisable(2)  

dsNcFasAlign 1.3.6.1.4.1.181.2.2.11.10
The E1 network interface Time Slot 0 NOT-FAS Word setting. The possible values are: VALUE DESCRIPTION ncFasWord(1) Use the NOT-FAS word ncNonFasWord(2) Do not use the NOT-FAS word
OBJECT-TYPE    
  INTEGER ncFasWord(1), ncNonFasWord(2)  

dsNcE1DLPath 1.3.6.1.4.1.181.2.2.11.11
The E1 network interface Sa bit usage. If Sa bits are being used for data link communications, both the near and far end units must agree on which Sa bit to use. Possible value are: VALUE DESCRIPTION ncSaNone(1) No Sa bits are being used for data link communications ncSaBit4(2) Use Sa bit 4 for data link communications ncSaBit5(3) Use Sa bit 5 for data link communications ncSaBit6(4) Use Sa bit 6 for data link communications ncSaBit7(5) Use Sa bit 7 for data link communications ncSaBit8(6) Use Sa bit 8 for data link communications ncTSn Use TimeSlot n for data link communications. These are only available for E1 units with In-Band Link hardware.
OBJECT-TYPE    
  INTEGER ncSaNone(1), ncSaBit4(2), ncSaBit5(3), ncSaBit6(4), ncSaBit7(5), ncSaBit8(6), ncTS1(7), ncTS2(8), ncTS3(9), ncTS4(10), ncTS5(11), ncTS6(12), ncTS7(13), ncTS8(14), ncTS9(15), ncTS10(16), ncTS11(17), ncTS12(18), ncTS13(19), ncTS14(20), ncTS15(21), ncTS16(22), ncTS17(23), ncTS18(24), ncTS19(25), ncTS20(26), ncTS21(27), ncTS22(28), ncTS23(29), ncTS24(30), ncTS25(31), ncTS26(32), ncTS27(33), ncTS28(34), ncTS29(35), ncTS30(36), ncTS31(37)  

dsNcKA 1.3.6.1.4.1.181.2.2.11.12
The status of sending E1 remote Frame Alarm into the NI during alarms. The Possible values are: VALUE DESCRIPTION ncFramedKeepAlive(1) Enable Framed Keep Alive ncUnFramedKeepAlive(2) Disabled Unframed Keep Alive
OBJECT-TYPE    
  INTEGER ncFramedKeepAlive(1), ncUnFramedKeepAlive(2)  

dsNcGenRfa 1.3.6.1.4.1.181.2.2.11.13
The status of sending E1 remote Frame Alarm into the NI during alarms. The Possible values are: VALUE DESCRIPTION ncGenRfaEnable(1) Enable RFA insertion ncGenRfaDisable(2) Disabled RFA insertion
OBJECT-TYPE    
  INTEGER ncGenRfaEnable(1), ncGenRfaDisable(2)  

dsNcPassTiRfa 1.3.6.1.4.1.181.2.2.11.14
The status of sending the RFA received on the network interface out the terminal interface. This function is not possible on a DSU only, it must be an add/drop. This function only works if at least one channel is assigned to the TI. The Possible values are: VALUE DESCRIPTION ncPassTiRfaEnable(1) Enable RFA re-generation ncPassTiRfaDisable(2) Disabled RFA re-generation
OBJECT-TYPE    
  INTEGER ncPassTiRfaEnable(1), ncPassTiRfaDisable(2)  

dsNcIdle 1.3.6.1.4.1.181.2.2.11.15
The idle code to be transmited in the idle NI and TI channels. This code is also sent in all TI channels when the TI is experiencing an OOF.
OBJECT-TYPE    
  INTEGER 0..255  

dsNcDdsType 1.3.6.1.4.1.181.2.2.11.16
The Possible values are: VALUE DESCRIPTION scDds56K(1) Set unit to 56K Operation scDds64K(2) Set unit to 56K Operation
OBJECT-TYPE    
  INTEGER scDds56K(1), scDds64K(2)  

dsScMonth 1.3.6.1.4.1.181.2.2.12.1
The calendar number of the current month. 1 is January.
OBJECT-TYPE    
  INTEGER 1..12  

dsScDay 1.3.6.1.4.1.181.2.2.12.2
The number of the current day.
OBJECT-TYPE    
  INTEGER 1..31  

dsScYear 1.3.6.1.4.1.181.2.2.12.3
The number of the current year. 95 is 1995.
OBJECT-TYPE    
  INTEGER 0..99  

dsScHour 1.3.6.1.4.1.181.2.2.12.4
The number of the current hour. 0 is 12:00am.
OBJECT-TYPE    
  INTEGER 0..23  

dsScMinutes 1.3.6.1.4.1.181.2.2.12.5
The number of the current minute.
OBJECT-TYPE    
  INTEGER 0..59  

dsScName 1.3.6.1.4.1.181.2.2.12.6
The Site Name of the unit.
OBJECT-TYPE    
  DisplayString Size(0..15)  

dsScSlotAddr 1.3.6.1.4.1.181.2.2.12.7
The Kentrox-specific slot address. The 01 in the address 01:02:003.
OBJECT-TYPE    
  INTEGER 0..15  

dsScShelfAddr 1.3.6.1.4.1.181.2.2.12.8
The Kentrox-specific shelf address. The 02 in the address 01:02:003.
OBJECT-TYPE    
  INTEGER 0..15  

dsScGroupAddr 1.3.6.1.4.1.181.2.2.12.9
The Kentrox-specific group address. The 003 in the address 01:02:003.
OBJECT-TYPE    
  INTEGER 0..255  

dsScFrontPanel 1.3.6.1.4.1.181.2.2.12.10
The status of the front panel buttons. The possible values are: VALUE DESCRIPTION scFpEnable(1) Enable the front panel buttons scFpDisable(2) Disable the front panel buttons
OBJECT-TYPE    
  INTEGER scFpEnable(1), scFpDisable(2)  

dsScDSCompatible 1.3.6.1.4.1.181.2.2.12.11
The status of the datasmart compatibility function. This should be set to scDSEnabled(1) when the far end unit is a eariler model datasmart, not a datasmart. The possible values are: VALUE DESCRIPTION scDSEnable(1) Enable the datasmart compatibility function scDSDisable(2) Disable the datasmart compatibility funcation
OBJECT-TYPE    
  INTEGER scDSEnable(1), scDSDisable(2)  

dsScClockSource 1.3.6.1.4.1.181.2.2.12.12
The source of the timing clock. The various options are: VALUE DESCRIPTION scTerminalTiming(1) Use the clock coming in on the Terminal Interface scThroughTiming(2) Use Through timing NI rx to Ti tx and TI rx to NI tx scInternalTiming(3) Use the internal clock scLoopTiming(4) Use the clock from the network scDP1Timing(5) Use the clock coming in on data port 1 scDP2Timing(6) Use the clock coming in on data port 2
OBJECT-TYPE    
  INTEGER scTerminalTiming(1), scThroughTiming(2), scInternalTiming(3), scLoopTiming(4), scDP1Timing(5), scDP2Timing(6)  

dsScAutologout 1.3.6.1.4.1.181.2.2.12.13
The time (in minutes) to wait for a keypress before logging the current user out. If this object is set to 0, autologout is disabled.
OBJECT-TYPE    
  INTEGER 0..60  

dsScZeroPerData 1.3.6.1.4.1.181.2.2.12.14
This object will zero all performance report counters if it is set to scZallStart(2).
OBJECT-TYPE    
  INTEGER scZallIdle(1), scZallStart(2)  

dsScWyv 1.3.6.1.4.1.181.2.2.12.15
The string returned by the user interface command WYV, What's Your Version.
OBJECT-TYPE    
  DisplayString Size(0..255)  

dsScAutoCfg 1.3.6.1.4.1.181.2.2.12.16
This object enables/disables the Auto-Configuration feature, which allows units in a daisy chain to be automatically configured by the Daisy Chain Controller. This feature is only available on the plug-in versions of datasmart.
OBJECT-TYPE    
  INTEGER scAcEnable(1), scAcDisable(2)  

dsScTftpSwdl 1.3.6.1.4.1.181.2.2.12.17
A text string used to initiate or check the status of a TFTP file transfer operation for doing a software download. To initiate a TFTP software download, set this variable to the value `tswdl:,`, where i represents the IP address of the host system, and the f represents the name of the file to be downloaded. Setting this variable to any other value will have no affect. Getting the value of this variable will return the status of the TFTP software download.
OBJECT-TYPE    
  DisplayString Size(0..255)  

dsScBoot 1.3.6.1.4.1.181.2.2.12.18
This variable is used to force a system reboot: scBootIdle Does nothing. scBootActive Reboots from the executing FLASH ROM bank. scBootInactive Reboots from the non-executing FLASH ROM bank.
OBJECT-TYPE    
  INTEGER scBootIdle(1), scBootActive(2), scBootInactive(3)  

dsScOperMode 1.3.6.1.4.1.181.2.2.12.19
fill in later. scTransparentMode Unit doesn't monitor FR traffic scMonitorMode Unit monitors FR traffic
OBJECT-TYPE    
  INTEGER scTransparentMode(1), scMonitorMode(2)  

dsScYearExtention 1.3.6.1.4.1.181.2.2.12.20
.
OBJECT-TYPE    
  INTEGER 1992..2091  

dsScMonthExtention 1.3.6.1.4.1.181.2.2.12.21
.
OBJECT-TYPE    
  INTEGER 1..12  

dsScDayExtention 1.3.6.1.4.1.181.2.2.12.22
.
OBJECT-TYPE    
  INTEGER 1..31  

dsScHourExtention 1.3.6.1.4.1.181.2.2.12.23
.
OBJECT-TYPE    
  INTEGER 0..24  

dsScMinExtention 1.3.6.1.4.1.181.2.2.12.24
.
OBJECT-TYPE    
  INTEGER 0..59  

dsScSecExtention 1.3.6.1.4.1.181.2.2.12.25
.
OBJECT-TYPE    
  INTEGER 0..59  

dsScPinK 1.3.6.1.4.1.181.2.2.12.26
.
OBJECT-TYPE    
  INTEGER pinKEnabled(1), pinKDisabled(2)  

dsTcFraming 1.3.6.1.4.1.181.2.2.13.1
The line framing for the Terminal Interface. The possible values are: VALUE DESCRIPTION tcSF(1) SF (D4) framing tcESF(2) ESF framing tcEricsson(3) Ericsson framing
OBJECT-TYPE    
  INTEGER tcSF(1), tcESF(2), tcEricsson(3)  

dsTcCoding 1.3.6.1.4.1.181.2.2.13.2
The line coding for the Terminal Interface. The possible values are: VALUE DESCRIPTION tcAmi(1) AMI line coding tcB8zs(2) B8ZS line coding
OBJECT-TYPE    
  INTEGER tcAmi(1), tcB8zs(2)  

dsTcIdle 1.3.6.1.4.1.181.2.2.13.3
The code that is sent out the idle DS0 channels of the terminal interface.
OBJECT-TYPE    
  INTEGER 0..255  

dsTcEqual 1.3.6.1.4.1.181.2.2.13.4
The line equalization for the Terminal Interface. The possible values are: VALUE DESCRIPTION tcTe0(1) 0-133 feet tcTe1(2) 133-266 feet tcTe2(3) 266-399 feet tcTe3(4) 399-533 feet tcTe4(5) 533-655 feet
OBJECT-TYPE    
  INTEGER tcTe0(1), tcTe1(2), tcTe2(3), tcTe3(4), tcTe4(5)  

dsTcMF16 1.3.6.1.4.1.181.2.2.13.5
The E1 terminal interface Time Slot 16 MultiFrame alignment signal setting. The possible values are: VALUE DESCRIPTION tcMF16Enable(1) Enable the Time Slot 16 MultiFrame alignment signal tcMF16Disable(2) Disabled the Time Slot 16 MultiFrame alignment signal
OBJECT-TYPE    
  INTEGER tcMF16Enable(1), tcMF16Disable(2)  

dsTcCRC 1.3.6.1.4.1.181.2.2.13.6
The E1 terminal interface CRC generation/checking setting. The possible values are: VALUE DESCRIPTION tcCrcEnable(1) Enable CRC generation/checking tcCrcDisable(2) Disable CRC generation/checking
OBJECT-TYPE    
  INTEGER tcCrcEnable(1), tcCrcDisable(2)  

dsTcFasAlign 1.3.6.1.4.1.181.2.2.13.7
The E1 terminal interface Time Slot 0 NOT-FAS Word setting. The possible values are: VALUE DESCRIPTION tcFasWord(1) Use the NOT-FAS word tcNonFasWord(2) Do not use the NOT-FAS word
OBJECT-TYPE    
  INTEGER tcFasWord(1), tcNonFasWord(2)  

dsTcAis 1.3.6.1.4.1.181.2.2.13.8
This object controls the sending of Alarm Indication Signal (AIS) alarms. The possible values are: VALUE DESCRIPTION tcAisEnable(1) Enable sending AIS alarms tcAisDisable(2) Disable sending AIS alarms
OBJECT-TYPE    
  INTEGER tcAisEnable(1), tcAisDisable(2)  

dsTcGenRfa 1.3.6.1.4.1.181.2.2.13.9
The status of sending E1 remote Frame Alarm into the TI during alarms. The Possible values are: VALUE DESCRIPTION tcGenRfaEnable(1) Enable RFA insertion tcGenRfaDisable(2) Disabled RFA insertion
OBJECT-TYPE    
  INTEGER tcGenRfaEnable(1), tcGenRfaDisable(2)  

dsTcPassTiRfa 1.3.6.1.4.1.181.2.2.13.10
The status of sending the RFA received on the terminal interface out the network interface. This function is not possible on a DSU only, it must be an add/drop. This function only works if at least one channel is assigned to the TI. The Possible values are: VALUE DESCRIPTION tcPassTiRfaEnable(1) Enable RFA re-generation tcPassTiRfaDisable(2) Disabled RFA re-generation
OBJECT-TYPE    
  INTEGER tcPassTiRfaEnable(1), tcPassTiRfaDisable(2)  

dsFpFr56 1.3.6.1.4.1.181.2.2.14.1
OBJECT IDENTIFIER    

dsFpFr56PwrLed 1.3.6.1.4.1.181.2.2.14.1.1
The current state of the FP PWR LED. The Possible values are: VALUE DESCRIPTION fpLedIndeterminate (1) LED is not present on unit fpLedOff (2) LED is OFF fpLedOnGreen (3) LED is ON and green fpLedBlinkGreen (4) LED is blinking green
OBJECT-TYPE    
  INTEGER fpLedIndeterminate(1), fpLedOff(2), fpLedOnGreen(3), fpLedBlinkGreen(4)  

dsFpFr56DnldFailLed 1.3.6.1.4.1.181.2.2.14.1.2
The current state of the FP DNLD/FAIL LED. The Possible values are: VALUE DESCRIPTION fpLedIndeterminate (1) LED is not present on unit fpLedOff (2) LED is OFF fpLedOnRed (3) LED is ON and red fpLedBlinkRed (4) LED is blinking red
OBJECT-TYPE    
  INTEGER fpLedIndeterminate(1), fpLedOff(2), fpLedOnRed(3), fpLedBlinkRed(4)  

dsFpFr56NiAlarmLed 1.3.6.1.4.1.181.2.2.14.1.3
The current state of the FP NI ALARM LED. The Possible values are: VALUE DESCRIPTION fpLedIndeterminate (1) LED is not present on unit fpLedOff (2) LED is OFF fpLedOnRed (3) LED is ON and red
OBJECT-TYPE    
  INTEGER fpLedIndeterminate(1), fpLedOff(2), fpLedOnRed(3)  

dsFpFr56NiDataLed 1.3.6.1.4.1.181.2.2.14.1.4
The current state of the FP NI DATA LED. The Possible values are: VALUE DESCRIPTION fpLedIndeterminate (1) LED is not present on unit fpLedOff (2) LED is OFF fpLedOnGreen (3) LED is ON and green
OBJECT-TYPE    
  INTEGER fpLedIndeterminate(1), fpLedOff(2), fpLedOnGreen(3)  

dsFpFr56TestLed 1.3.6.1.4.1.181.2.2.14.1.5
The current state of the FP TEST LED. The Possible values are: VALUE DESCRIPTION fpLedIndeterminate (1) LED is not present on unit fpLedOff (2) LED is OFF fpLedOnYellow (3) LED is ON and yellow
OBJECT-TYPE    
  INTEGER fpLedIndeterminate(1), fpLedOff(2), fpLedOnYellow(3)  

dsFpFr56DpCtsTxLed 1.3.6.1.4.1.181.2.2.14.1.6
The current state of the FP DP CTS TX LED. The Possible values are: VALUE DESCRIPTION fpLedIndeterminate (1) LED is not present on unit fpLedOff (2) LED is OFF fpLedOnYellow (3) LED is ON and yellow
OBJECT-TYPE    
  INTEGER fpLedIndeterminate(1), fpLedOff(2), fpLedOnYellow(3)  

dsFpFr56DpRtsRxLed 1.3.6.1.4.1.181.2.2.14.1.7
The current state of the FP DP RTS RX LED. The Possible values are: VALUE DESCRIPTION fpLedIndeterminate (1) LED is not present on unit fpLedOff (2) LED is OFF fpLedOnYellow (3) LED is ON and yellow
OBJECT-TYPE    
  INTEGER fpLedIndeterminate(1), fpLedOff(2), fpLedOnYellow(3)  

dsFpFr56FrLinkLed 1.3.6.1.4.1.181.2.2.14.1.8
The current state of the FP FRAME RELAY LINK LED. The Possible values are: VALUE DESCRIPTION fpLedIndeterminate (1) LED is not present on unit fpLedOff (2) LED is OFF fpLedOnGreen (3) LED is ON and green fpLedBlinkGreen (4) LED is blinking green
OBJECT-TYPE    
  INTEGER fpLedIndeterminate(1), fpLedOff(2), fpLedOnGreen(3), fpLedBlinkGreen(4)