CTRON-DECIV-ROUTER-MIB

File: CTRON-DECIV-ROUTER-MIB.mib (100017 bytes)

Imported modules

RFC-1212 RFC1213-MIB ROUTER-OIDS
RFC1155-SMI

Imported symbols

OBJECT-TYPE DisplayString nwRtrProtoSuites
Counter TimeTicks Gauge

Defined Types

DecIVAddress  
STRING    

NwDecIVFwdIfEntry  
SEQUENCE    
  nwDecIVFwdIfIndex INTEGER
  nwDecIVFwdIfAdminStatus INTEGER
  nwDecIVFwdIfOperStatus INTEGER
  nwDecIVFwdIfOperationalTime TimeTicks
  nwDecIVFwdIfControl INTEGER
  nwDecIVFwdIfMtu INTEGER
  nwDecIVFwdIfForwarding INTEGER
  nwDecIVFwdIfFrameType INTEGER
  nwDecIVFwdIfAclIdentifier INTEGER
  nwDecIVFwdIfAclStatus INTEGER
  nwDecIVFwdIfCacheControl INTEGER
  nwDecIVFwdIfCacheEntries Counter
  nwDecIVFwdIfCacheHits Counter
  nwDecIVFwdIfCacheMisses Counter

NwDecIVFwdIfCtrEntry  
SEQUENCE    
  nwDecIVFwdIfCtrIfIndex INTEGER
  nwDecIVFwdIfCtrAdminStatus INTEGER
  nwDecIVFwdIfCtrReset INTEGER
  nwDecIVFwdIfCtrOperationalTime TimeTicks
  nwDecIVFwdIfCtrInPkts Counter
  nwDecIVFwdIfCtrOutPkts Counter
  nwDecIVFwdIfCtrFwdPkts Counter
  nwDecIVFwdIfCtrFilteredPkts Counter
  nwDecIVFwdIfCtrDiscardPkts Counter
  nwDecIVFwdIfCtrAddrErrPkts Counter
  nwDecIVFwdIfCtrLenErrPkts Counter
  nwDecIVFwdIfCtrHdrErrPkts Counter
  nwDecIVFwdIfCtrInBytes Counter
  nwDecIVFwdIfCtrOutBytes Counter
  nwDecIVFwdIfCtrFwdBytes Counter
  nwDecIVFwdIfCtrFilteredBytes Counter
  nwDecIVFwdIfCtrDiscardBytes Counter
  nwDecIVFwdIfCtrHostInPkts Counter
  nwDecIVFwdIfCtrHostOutPkts Counter
  nwDecIVFwdIfCtrHostDiscardPkts Counter
  nwDecIVFwdIfCtrHostInBytes Counter
  nwDecIVFwdIfCtrHostOutBytes Counter
  nwDecIVFwdIfCtrHostDiscardBytes Counter

NwDecIVProtoIfEntry  
SEQUENCE    
  nwDecIVProtoIfIndex INTEGER
  nwDecIVProtoIfAdminStatus INTEGER
  nwDecIVProtoIfOperStatus INTEGER
  nwDecIVProtoIfOperationalTime TimeTicks
  nwDecIVProtoIfVersion INTEGER
  nwDecIVProtoIfAdvertisement INTEGER
  nwDecIVProtoIfFloodDelay INTEGER
  nwDecIVProtoIfRequestDelay INTEGER
  nwDecIVProtoIfPriority INTEGER
  nwDecIVProtoIfHelloTimer INTEGER
  nwDecIVProtoIfSplitHorizon INTEGER
  nwDecIVProtoIfPoisonReverse INTEGER
  nwDecIVProtoIfSnooping INTEGER
  nwDecIVProtoIfType INTEGER
  nwDecIVProtoIfXmitCost INTEGER
  nwDecIVProtoIfAclIdentifier INTEGER
  nwDecIVProtoIfAclStatus INTEGER

NwDecIVProtoIfCtrEntry  
SEQUENCE    
  nwDecIVProtoIfCtrIfIndex INTEGER
  nwDecIVProtoIfCtrAdminStatus INTEGER
  nwDecIVProtoIfCtrReset INTEGER
  nwDecIVProtoIfCtrOperationalTime TimeTicks
  nwDecIVProtoIfCtrInPkts Counter
  nwDecIVProtoIfCtrOutPkts Counter
  nwDecIVProtoIfCtrFilteredPkts Counter
  nwDecIVProtoIfCtrDiscardPkts Counter
  nwDecIVProtoIfCtrInBytes Counter
  nwDecIVProtoIfCtrOutBytes Counter
  nwDecIVProtoIfCtrFilteredBytes Counter
  nwDecIVProtoIfCtrDiscardBytes Counter

NwDecIVFibEntry  
SEQUENCE    
  nwDecIVFibNodeId DecIVAddress
  nwDecIVFibNextHopNodeId DecIVAddress
  nwDecIVFibNextHopIf INTEGER
  nwDecIVFibRouteType INTEGER

NwDecIVAclEntry  
SEQUENCE    
  nwDecIVAclIdentifier INTEGER
  nwDecIVAclSequence INTEGER
  nwDecIVAclPermission INTEGER
  nwDecIVAclMatches Counter
  nwDecIVAclDestAddress DecIVAddress
  nwDecIVAclSrcAddress DecIVAddress

NwDecIVHostMapEntry  
SEQUENCE    
  nwDecIVHostMapIfIndex INTEGER
  nwDecIVHostMapDecIVAddr DecIVAddress
  nwDecIVHostMapType INTEGER
  nwDecIVHostMapCircuitID INTEGER
  nwDecIVHostMapFraming INTEGER
  nwDecIVHostMapPortNumber INTEGER

NwDecIVEventFilterEntry  
SEQUENCE    
  nwDecIVEventFltrProtocol INTEGER
  nwDecIVEventFltrIfNum INTEGER
  nwDecIVEventFltrControl INTEGER
  nwDecIVEventFltrType INTEGER
  nwDecIVEventFltrSeverity INTEGER
  nwDecIVEventFltrAction INTEGER

NwDecIVEventEntry  
SEQUENCE    
  nwDecIVEventNumber INTEGER
  nwDecIVEventTime TimeTicks
  nwDecIVEventType INTEGER
  nwDecIVEventSeverity INTEGER
  nwDecIVEventProtocol INTEGER
  nwDecIVEventIfNum INTEGER
  nwDecIVEventTextString STRING

Defined Values

nwDecIVRouter 1.3.6.1.4.1.52.4.2.2.2.3.3
OBJECT IDENTIFIER    

nwDecIVMibs 1.3.6.1.4.1.52.4.2.2.2.3.3.1
OBJECT IDENTIFIER    

nwDecIVComponents 1.3.6.1.4.1.52.4.2.2.2.3.3.2
OBJECT IDENTIFIER    

nwDecIVSystem 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1
OBJECT IDENTIFIER    

nwDecIVForwarding 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2
OBJECT IDENTIFIER    

nwDecIVTopology 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4
OBJECT IDENTIFIER    

nwDecIVFib 1.3.6.1.4.1.52.4.2.2.2.3.3.2.5
OBJECT IDENTIFIER    

nwDecIVEndSystems 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6
OBJECT IDENTIFIER    

nwDecIVAccessControl 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7
OBJECT IDENTIFIER    

nwDecIVFilters 1.3.6.1.4.1.52.4.2.2.2.3.3.2.8
OBJECT IDENTIFIER    

nwDecIVRedirector 1.3.6.1.4.1.52.4.2.2.2.3.3.2.9
OBJECT IDENTIFIER    

nwDecIVEvent 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10
OBJECT IDENTIFIER    

nwDecIVWorkGroup 1.3.6.1.4.1.52.4.2.2.2.3.3.2.11
OBJECT IDENTIFIER    

nwDecIVSysConfig 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1
OBJECT IDENTIFIER    

nwDecIVSysAdministration 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2
OBJECT IDENTIFIER    

nwDecIVFwdSystem 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1
OBJECT IDENTIFIER    

nwDecIVFwdInterfaces 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2
OBJECT IDENTIFIER    

nwDecIVFwdCounters 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1
OBJECT IDENTIFIER    

nwDecIVFwdIfConfig 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1
OBJECT IDENTIFIER    

nwDecIVFwdIfCounters 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2
OBJECT IDENTIFIER    

nwDecIVDistanceVector 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1
OBJECT IDENTIFIER    

nwDecIVLinkState 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.2
OBJECT IDENTIFIER    

nwDecIVProto 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1
OBJECT IDENTIFIER    

nwDecIVProtoSystem 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1
OBJECT IDENTIFIER    

nwDecIVProtoInterface 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2
OBJECT IDENTIFIER    

nwDecIVProtoConfig 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1
OBJECT IDENTIFIER    

nwDecIVProtoCounters 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2
OBJECT IDENTIFIER    

nwDecIVProtoIfConfig 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1
OBJECT IDENTIFIER    

nwDecIVProtoIfCounters 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2
OBJECT IDENTIFIER    

nwDecIVHostsSystem 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.1
OBJECT IDENTIFIER    

nwDecIVHostsInterfaces 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.2
OBJECT IDENTIFIER    

nwDecIVHostsToMedia 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3
OBJECT IDENTIFIER    

nwDecIVEventLogConfig 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.1
OBJECT IDENTIFIER    

nwDecIVEventLogFilterTable 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2
OBJECT IDENTIFIER    

nwDecIVEventLogTable 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3
OBJECT IDENTIFIER    

nwDecIVMibRevText 1.3.6.1.4.1.52.4.2.2.2.3.3.1.1
Indicates the current revision level of the DECnet Phase IV MIB in textual format.
OBJECT-TYPE    
  DisplayString  

nwDecIVSysRouterId 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.1
The DECnet Address used to uniquely identify the host (device) running DECnet Phase IV Routing Services. Since DECnet Phase IV uses a single address to identify the host and all of its router ports, rather than using an address per router port, nwDecIVSysRouterID is the DECnet node address for all the router ports on the device.
OBJECT-TYPE    
  DecIVAddress  

nwDecIVNodeType 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.2
Specifies the node type. Setting this value to 2, (routing-iv), establishes the Routing Services-enabled device as a DECnet Level 1, intra-area router. Setting this value to 2, establishes the Routing Services-enabled device as a DECnet Phase IV Level 2, or inter-area router.
OBJECT-TYPE    
  INTEGER other(1), routing-iv(2), area(3)  

nwDecIVMaxNodes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.3
Specifies the maximum number of DECnet nodes allowed within an area.
OBJECT-TYPE    
  INTEGER  

nwDecIVMaxBRA 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.4
Specifies the maximum number of router adjacencies supported by this node.
OBJECT-TYPE    
  INTEGER  

nwDecIVMaxBEA 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.5
Specifies the maximum number of endnode adjacencies supported by this node.
OBJECT-TYPE    
  INTEGER  

nwDecIVMaxHops 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.6
Specifies the maximum number of hops allowed for a valid route within the area. Any intra-area route consisting of a greater number of hops than specified by nwDecIVMaxHops is considered unreachable.
OBJECT-TYPE    
  INTEGER  

nwDecIVMaxCost 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.7
Specifies the maximum cost allowed for a valid route within the area. Any intra-area route with a cost greater than nwDecIVMaxCost is considered unreachable.
OBJECT-TYPE    
  INTEGER  

nwDecIVMaxVisits 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.8
Specifies the maximum number of intra-area hops a packet can be forwarded. A packet is dropped once it has been forwarded nwDecIVMaxVisits.
OBJECT-TYPE    
  INTEGER  

nwDecIVNonBroadcastTimer 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.9
Specifies the periodic interval (in seconds) at which DECnet Routing Services advertises its route table, on any non-broadcast networks attached to any router port configured and enabled for DECnet Phase IV Routing Services.
OBJECT-TYPE    
  TimeTicks  

nwDecIVBroadcastTimer 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.10
Specifies the periodic interval (in seconds) at which DECnet Routing Services advertises its route table on any multi-access broadcast networks attached to any router port configured and enabled for DECnet Phase IV Routing Services.
OBJECT-TYPE    
  TimeTicks  

nwDecIVAreas 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.11
Specifies the maximum number of areas allowed within a Level 2 (inter-area)routing domain.
OBJECT-TYPE    
  INTEGER  

nwDecIVMaxAreaHops 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.12
Specifies the maximum number of areas that can be hopped by a valid inter-area route. Any inter-area route requiring a greater number of areas to be hopped than specified by nwDecIVMaxAreaHops is considered invalid.
OBJECT-TYPE    
  INTEGER  

nwDecIVMaxAreaCost 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.1.13
Specifies the maximum cost allowed for a valid Level 2 (inter-area) route. Any inter-area route with a cost greater than nwDecIVMaxAreaCost is considered unreachable.
OBJECT-TYPE    
  INTEGER  

nwDecIVSysAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.1
Sets the administrative state of DECnet Phase IV Routing Services, system-wide. Enabled (3) causes DECnet Phase IV system-wide Routing Services to become active on all router ports configured and enabled for DECnet Phase IV Routing Services. Disabled (2) causes DECnet Phase IV Routing Services to become inactive system-wide.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwDecIVSysOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.2
Indicates the current operating condition of DECnet Phase IV Routing Services system-wide. The value of nwDecIVSysOperStatus indicates any problem with your DECnet Phase IV Routing Services configuration. A value of 6 indicates that regardless of the value of nwDecIVSysAdminStatus, DECnet Phase IV Routing Services is not operating because of an invalid configuration.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pending-disable(4), pending-enable(5), invalid-config(6)  

nwDecIVSysAdminReset 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.3
Resets DECnet Phase IV Routing Services, system-wide. Reset (2) forces a restart of DECnet Phase IV Routing Services without a graceful shutdown on any active router ports and without affecting any other routing services.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwDecIVSysOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.4
Indicates the elapsed time, in hundredths of a second, that nwDecIVSysOperStatus has been in it's current state.
OBJECT-TYPE    
  TimeTicks  

nwDecIVSysVersion 1.3.6.1.4.1.52.4.2.2.2.3.3.2.1.2.5
Indicates the current revision level of the DECnet Phase IV Routing Services firmware, in textual format.
OBJECT-TYPE    
  DisplayString  

nwDecIVFwdCtrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.1
Sets the administrative state of the aggregate (system-wide) DECnet packet and byte counters. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwDecIVFwdCtrReset 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.2
Resets the aggregate (system-wide) DECnet packet and byte counters. Reset (2) resets the DECnet aggregate counters to 0. nwDecIVFwdCtrOperationalTime is also reset to 0.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwDecIVFwdCtrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.3
Indicates the elapsed time, in hundredths of a second, that DecIVFwdCtrOperStatus has been in the current state.
OBJECT-TYPE    
  TimeTicks  

nwDecIVFwdCtrInPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.4
Indicates the total number of DECnet packets that have been received, system-wide, during nwDecIVFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVFwdCtrOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.5
Indicates the total number of DECnet packets that have been transmitted, system-wide, during nwDecIVFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVFwdCtrFwdPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.6
Indicates the total number of DECnet packets that have been forwarded, system-wide, during nwDecIVFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVFwdCtrFilteredPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.7
Indicates the total number of DECnet packets that have been administratively filtered, system-wide, during nwDecIVFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVFwdCtrDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.8
Indicates the total number of DECnet packets that have been discarded, system-wide, during nwDecIVFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVFwdCtrAddrErrPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.9
Indicates the total number of DECnet packets that have been discarded, system-wide, during nwDecIVFwdCtrOperationalTime, because of addressing errors in the DECnet header.
OBJECT-TYPE    
  Counter  

nwDecIVFwdCtrLenErrPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.10
Indicates the total number of DECnet packets that have been discarded, system-wide, during nwDecIVFwdCtrOperationalTime, because an invalid packet length is contained in the DECnet header.
OBJECT-TYPE    
  Counter  

nwDecIVFwdCtrHdrErrPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.11
Indicates the total number of DECnet packets that have been discarded, system-wide, during nwDecIVFwdCtrOperationalTime, because of an invalid DECnet header.
OBJECT-TYPE    
  Counter  

nwDecIVFwdCtrInBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.12
Indicates the total number of bytes in the DECnet packets that have been received, system-wide, during nwDecIVFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVFwdCtrOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.13
Indicates the total number of bytes in the DECnet packets that have been transmitted, system-wide, during nwDecIVFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVFwdCtrFwdBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.14
Indicates the total number of bytes in the DECnet packets that have been forwarded, system-wide, during nwDecIVFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVFwdCtrFilteredBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.15
Indicates the total number of bytes in the DECnet packets that have been administratively filtered, system-wide, during nwDecIVFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVFwdCtrDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.16
Indicates the total number of bytes in the DECnet packets that have been discarded, system wide, during nwDecIVFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVFwdCtrHostInPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.17
Indicates the total number of DECnet packets that have been successfully delivered to the local host, during nwDecIVFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVFwdCtrHostOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.18
Indicates the total number of DECnet packets that have been transmitted by the local host, during nwDecIVFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVFwdCtrHostDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.19
Indicates the total number of DECnet packets that have been discarded by the local host, during nwDecIVFwdCtrOperationalTime, due to a lack of host resources.
OBJECT-TYPE    
  Counter  

nwDecIVFwdCtrHostInBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.20
Indicates the total number of bytes in the DECnet packets that have been received by the local host, during nwDecIVFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVFwdCtrHostOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.21
Indicates the total number of bytes in the DECnet packets that have been transmitted by the local host, during nwDecIVFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVFwdCtrHostDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.1.1.22
Indicates the total number of bytes in the DECnet packets that have been discarded by the local host, during nwDecIVFwdCtrOperationalTime, due to a lack of host resources.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfTable 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1
This table contains an entry for each router port. This table is indexed by nwDecIVFwdIfIndex, which indicates the value of MIB 2 ifIndex, which identifies the router port for which each entry exists.
OBJECT-TYPE    
  SEQUENCE OF  
    NwDecIVFwdIfEntry

nwDecIVFwdIfEntry 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1
Each entry specifies the DECnet Phase IV Routing Services configuration for the router port for which the entry exists.
OBJECT-TYPE    
  NwDecIVFwdIfEntry  

nwDecIVFwdIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.1
Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwDecIVFwdIfAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.2
Sets the administrative state of DECnet Phase IV Routing Services on the router port for which the entry exists. Enabled (3) causes DECnet Phase IV Routing Services to become active. Disabled (2) causes it to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwDecIVFwdIfOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.3
Indicates the current operating condition of DECnet Phase IV Routing Services on the router port for which the entry exists. The value of nwDecIVFwdIfOperStatus indicates any problem with the configuration of DECnet Phase IV Routing Services on the router port. value of 6 indicates that regardless of the value of nwDecIVFwdIfAdminStatus, DECnet Phase IV Routing Services is not operating because of an invalid port-level configuration.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pending-disable(4), pending-enable(5), invalid-config(6)  

nwDecIVFwdIfOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.4
Indicates the elapsed time, in hundredths of a second, that nwDecIVFwdIfOperStatus has been in its current state.
OBJECT-TYPE    
  TimeTicks  

nwDecIVFwdIfControl 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.5
This object does not apply to this protocol. It is a common object, inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER other(1), add(2), delete(3)  

nwDecIVFwdIfMtu 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.6
Specifies the Maximum Transmission Unit (MTU) for DECnet packets on the router port for which the entry exists. This includes the DECnet header and data, but does not include framing.
OBJECT-TYPE    
  INTEGER  

nwDecIVFwdIfForwarding 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.7
Controls the forwarding of DECnet packets on the router port for which the entry exists. Enabled (3) causes DECnet packets to be forwarded. Disabled (2) prevents DECnet packets from being forwarded.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwDecIVFwdIfFrameType 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.8
Specifies the framing type for DECnet packets forwarded on the router port for which the entry exists. Some frame types are only valid for specific media types. The comments reflect those valid media types.
OBJECT-TYPE    
  INTEGER other(1), ethernet(2), snap(3), nativewan(8), encapenet(9), encapenetsnap(11), encaptrsnap(14), encapfddisnap(16), canonical(17)  

nwDecIVFwdIfAclIdentifier 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.9
Specifies the Access Control ID of the access control list in effect for DECnet packets being routed on the router port for which the entry exists. A value of 0 indicates that no access control list is in effect.
OBJECT-TYPE    
  INTEGER  

nwDecIVFwdIfAclStatus 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.10
Controls the operation of any access control list configured for DECnet traffic on the router port for which the entry exists. Enabled (3) applies the access control list indicated by the value of nwDecIVFwdIfAclIdentifier to all DECnet traffic being routed on the port. Disabled (2) prevents the access control list from being applied.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwDecIVFwdIfCacheControl 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.11
This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER other(1), disable(2), enable(3)  

nwDecIVFwdIfCacheEntries 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.12
This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCacheHits 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.13
This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCacheMisses 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.1.1.1.14
This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCtrTable 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1
This table contains an entry for each router port configured and enabled for DECnet Phase IV Routing Services.
OBJECT-TYPE    
  SEQUENCE OF  
    NwDecIVFwdIfCtrEntry

nwDecIVFwdIfCtrEntry 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1
Each entry indicates the current packet and byte count of DECnet packets on each router port for which the entry exists.
OBJECT-TYPE    
  NwDecIVFwdIfCtrEntry  

nwDecIVFwdIfCtrIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.1
Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwDecIVFwdIfCtrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.2
Sets the administrative state of the per-port DECnet packet and byte counters on the router port for which the entry exists. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwDecIVFwdIfCtrReset 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.3
Resets the per-port DECnet packet and byte counters on the router port for which the entry exists. Reset (2) resets the counters to 0. nwDecIVFwdIfCtrOperationalTime is also reset to 0.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwDecIVFwdIfCtrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.4
Indicates the elapsed time, in hundredths of a second, that the per-port DECnet packet and byte counters have been active on the router port for which the entry exists.
OBJECT-TYPE    
  TimeTicks  

nwDecIVFwdIfCtrInPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.5
Indicates the total number of DECnet packets that have been received, during nwDecIVFwdIfCtrOperationaltime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCtrOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.6
Indicates the total number of DECnet packets that have been transmitted, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCtrFwdPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.7
Indicates the total number of DECnet packets that have been forwarded on the router port for which the entry exists, during nwDecIVFwdCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCtrFilteredPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.8
Indicates the total number of DECnet packets that have been administratively filtered, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCtrDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.9
Indicates the total number of DECnet packets that have been discarded (dropped), during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCtrAddrErrPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.10
Indicates the total number of DECnet packets that have been discarded because of addressing errors in the DECnet header, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCtrLenErrPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.11
Indicates the total number of DECnet packets that have been discarded because an invalid packet length was contained in the DECnet header, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCtrHdrErrPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.12
Indicates the total number of DECnet packets that have been discarded because of an invalid DECnet header, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCtrInBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.13
Indicates the total number of bytes in the DECnet packets that have been received, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCtrOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.14
Indicates the total number of bytes in the DECnet packets that have been transmitted, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCtrFwdBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.15
Indicates the total number of bytes in the DECnet packets that have been forwarded, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCtrFilteredBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.16
Indicates the total number of bytes in the DECnet packets that have been administratively filtered, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCtrDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.17
Indicates the total number of bytes in the DECnet packets that have been discarded, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCtrHostInPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.18
Indicates the total number of DECnet packets that have been delivered to the local host, during nwDecIVFwdIfCtrOperationalTime, that were received on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCtrHostOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.19
Indicates the total number of DECnet packets that have been transmitted by the local host, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCtrHostDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.20
Indicates the total number of DECnet packets that have been discarded by the local host, during nwDecIVFwdIfCtrOperationalTime, that were received on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCtrHostInBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.21
Indicates the total number of bytes in the DECnet packets that have been delivered to the local host, during nwDecIVFwdIfCtrOperationalTime, that were received on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCtrHostOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.22
Indicates the total number of bytes in the DECnet packets that have been transmitted by the local host, during nwDecIVFwdIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVFwdIfCtrHostDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.2.2.2.1.1.23
Indicates the total number of bytes in the DECnet packets that have been discarded by the local host, due to a lack of host resources, that were received on the router port for which the entry exists, during nwDecIVFwdIfCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVProtoAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.1
Sets the administrative state of the DECnet Phase IV distance-vector-based routing protocol system-wide. Enabled (3) causes the routing protocol to become active on all router ports configured and enabled for DECnet Routing Services. Disabled (2) causes the routing protocol to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwDecIVProtoOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.2
Indicates the current operating condition of the DECnet Phase IV distance-vector-based routing protocol system-wide. The value of nwDecIVProtoOperStatus indicates any problem with the DECnet Phase IV distance-vector-based routing protocol configuration. A value of 6 indicates that regardless of the value of nwDecIVProtoAdminStatus, the DECnet Phase IV distance-vector-based routing protocol is not operating because of an invalid configuration.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pending-disable(4), pending-enable(5), invalid-config(6)  

nwDecIVProtoAdminReset 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.3
Resets the DECnet Phase IV distance-vector-based routing protocol. Reset (2) forces a system-wide restart of the protocol without a graceful shut-down on any active router ports.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwDecIVProtoOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.4
Indicates the elapsed time, in hundredths of a second, that nwDecIVProtoOperStatus has been in current state.
OBJECT-TYPE    
  TimeTicks  

nwDecIVProtoVersion 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.5
Indicates the current revision level of the DECnet Phase IV distance-vector-based routing protocol firmware, in textual format.
OBJECT-TYPE    
  DisplayString  

nwDecIVProtoStackSize 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.6
Specifies the stack size of the DECnet Phase IV distance-vector- based routing protocol thread. In order for a change of this value to take effect, the protocol (nwDecIVProtoAdminReset), DECnet Phase IV Routing Services (nwDecIVSysAdminReset), or the device running Routing Services must be reset.
OBJECT-TYPE    
  INTEGER  

nwDecIVProtoThreadPriority 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.7
Specifies the run-time execution priority of the DECnet Phase IV distance-vector-based routing protocol thread. In order for a change of this value to take effect, the protocol (nwDecIVProtoAdminReset), DECnet Phase IV Routing Services (nwDecIVSysAdminReset), or the device running Routing Services must be reset.
OBJECT-TYPE    
  INTEGER  

nwDecIVProtoDatabaseThreshold 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.8
This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER  

nwDecIVProtoAgeOut 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.9
This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER  

nwDecIVProtoHoldDown 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.1.10
This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER  

nwDecIVProtoCtrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.1
Sets the administrative state of the aggregate (system-wide) DECnet Phase IV distance-vector-based routing protocol packet and byte counters. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwDecIVProtoCtrReset 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.2
Resets the aggregate (system-wide) DECnet Phase IV distance-vector-based routing protocol packet and byte counters. Reset (2) resets the DECnet aggregate counters to 0. nwDecIVProtoCtrOperationalTime is also reset to 0.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwDecIVProtoCtrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.3
Indicates the elapsed time, in hundredths of a second, that nwDecIVProtoCtrAdminStatus has been in it's current state.
OBJECT-TYPE    
  TimeTicks  

nwDecIVProtoCtrInPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.4
Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been received, system-wide, during nwDecIVProtoCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVProtoCtrOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.5
Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been transmitted, system-wide, during nwDecIVProtoCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVProtoCtrFilteredPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.6
Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been administratively filtered, system-wide, during nwDecIVProtoCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVProtoCtrDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.7
Indicates the total number of the DECnet Phase IV distance-vector -based routing protocol packets that have been discarded, system-wide, during nwDecIVProtoCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVProtoCtrInBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.8
Indicates the total number of bytes in the DECnet Phase IV distance-vector based routing protocol packets that have been received, system-wide, during nwDecIVProtoCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVProtoCtrOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.9
Indicates the total number of bytes in the DECnet Phase IV distance-vectorbased routing protocol packets that have been transmitted, system-wide, during nwDecIVProtoCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVProtoCtrFilteredBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.10
Indicates the total number of bytes in the DECnet Phase IV distance-vectorbased routing protocol packets that have been administratively filtered, system-wide, during nwDecIVProtoCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVProtoCtrDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.1.2.11
Indicates the total number of bytes in the DECnet Phase IV distance-vectorbased routing protocol packets that have been discarded system-wide, during nwDecIVProtoCtrOperationalTime.
OBJECT-TYPE    
  Counter  

nwDecIVProtoIfTable 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1
This table contains an entry for each router port. Each entry can contain different values, allowing the routing protocol configuration to vary from router port to router port. This table is indexed by nwDecIVProtoIfIndex, which indicates the value of MIB 2 ifIndex, which identifies the router port for which each entry exists.
OBJECT-TYPE    
  SEQUENCE OF  
    NwDecIVProtoIfEntry

nwDecIVProtoIfEntry 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1
Each entry contains the DECnet Phase IV distance-vector-based routing protocol configuration for the router port for which the entry exists.
OBJECT-TYPE    
  NwDecIVProtoIfEntry  

nwDecIVProtoIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.1
Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwDecIVProtoIfAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.2
Sets the administrative state of the DECnet Phase IV distance-vector-based routing protocol on the router port for which the entry exists. Enabled (3) causes the routing protocol to become active on the router port. Disabled (2) causes it to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwDecIVProtoIfOperStatus 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.3
Indicates the current operating condition of the DECnet Phase IV distance-vector-based routing protocol on the router port for which the entry exists. The value of nwDecIVProtoIfOperStatus indicates any problem with your routing protocol configuration on the router port. A value of 6 indicates that regardless of the value of nwDecIVProtoIfAdminStatus, the routing protocol is not operating because of an invalid configuration.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), pending-disable(4), pending-enable(5)  

nwDecIVProtoIfOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.4
Indicates the elapsed time, in hundredths of a second, that nwDecIVProtoIfOperStatus has been in it`s current state.
OBJECT-TYPE    
  TimeTicks  

nwDecIVProtoIfVersion 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.5
Indicates the revision level of the DECnet Phase IV distance-vector-based routing protocol firmware on the router port for which the entry exists, in textual format.
OBJECT-TYPE    
  INTEGER  

nwDecIVProtoIfAdvertisement 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.6
Sets the interval, in seconds, at which the DECnet Phase IV distance-vectorbased routing protocol advertises its route table on the router port for which the entry exists. Change this value to cause the DECnet Phase IV distance-vector-based routing protocol to advertise its route table more or less frequently on the router port.
OBJECT-TYPE    
  INTEGER  

nwDecIVProtoIfFloodDelay 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.7
This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER  

nwDecIVProtoIfRequestDelay 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.8
This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER  

nwDecIVProtoIfPriority 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.9
Sets the priority of the DECnet Phase IV distance-vector-based routing protocol on the router port for which the entry exists. Within an area, the router with the highest value for nwDecIVProtoIfPriority becomes the priority or designated router. The highest possible value for nwDecIVProtocolIfPriority is 127. Set this value high to cause your DECnet Phase IV Routing Services-enabled device to become the designated router. Set this value low to guarantee that it does not become the designated router.
OBJECT-TYPE    
  INTEGER  

nwDecIVProtoIfHelloTimer 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.10
Sets the interval, in seconds, at which DECnet Phase IV distance-vector-based routing protocol sends Hello packets on the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwDecIVProtoIfSplitHorizon 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.11
This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwDecIVProtoIfPoisonReverse 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.12
This object does not apply to this protocol. It is a common object inherited from the MIB framework used to provide a common management interface to all the Cabletron Routing Services protocol-specific MIBs. Setting this object has no effect.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwDecIVProtoIfSnooping 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.13
Controls the operation of DECnet Phase IV distance-vector-based routing protocol snooping on the router port. When snooping is enabled the DECnet Phase IV distance-vector-based routing protocol operates in passive mode, so that it receives route information, builds and maintains a route table, but does not advertise the route table or send updates on the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwDecIVProtoIfType 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.14
Indicates whether the directly connected network segment does or does not support broadcast media access.
OBJECT-TYPE    
  INTEGER other(1), bma(2), nbma(3)  

nwDecIVProtoIfXmitCost 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.15
Sets the cost of transmitting a packet on the network segment connected to the router port for which the entry exists. The DECnet Phase IV distance-vector-based routing protocol picks the route with the least total nwDecIVProtoIfXmitCost as the best route. If nwDecIVProtocolIfXmitCost, also known as path cost, is the same for all possible routes , the best route chosen is the route with the least number of hops is chosen as the best route.
OBJECT-TYPE    
  INTEGER  

nwDecIVProtoIfAclIdentifier 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.16
Specifies the Access Control ID of the access control list in effect for DECnet Phase IV distance-vector-based routing protocol packets on the router port for which the entry exists. A value of 0 indicates that there is no access control list in effect for DECnet Phase IV distance-vector-based routing protocol packets on the router port.
OBJECT-TYPE    
  INTEGER  

nwDecIVProtoIfAclStatus 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.1.1.1.17
Controls the operation of the access control list identified by nwDecIVProtoIfAclIdentifier. Enabled (3) applies the access control list to all DECnet Phase IV distance-vector-based routing protocol packet traffic on the router port for which the entry exists. Disabled (2) prevents the access control list from being applied.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwDecIVProtoIfCtrTable 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1
This table contains an entry for each router port. This table is indexed by nwDecIVProtoIfCtrIfIndex which indicates the value of MIB2 ifindex, which identifies the router port for which the entry exists.
OBJECT-TYPE    
  SEQUENCE OF  
    NwDecIVProtoIfCtrEntry

nwDecIVProtoIfCtrEntry 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1
Each entry indicates the current packet and byte count of DECnet Phase IV distance-vector-based routing protocol packets on the router port for which the entry exists.
OBJECT-TYPE    
  NwDecIVProtoIfCtrEntry  

nwDecIVProtoIfCtrIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.1
Indicates the value of MIB 2 ifindex, which identifies the router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwDecIVProtoIfCtrAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.2
Sets the administrative state of the per-port DECnet Phase IV distance-vectorbased routing protocol packet and byte counters on the router port for which the entry exists. Enabled (3) causes these counters to become active. Disabled (2) causes these counters to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwDecIVProtoIfCtrReset 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.3
Resets the per-port DECnet Phase IV distance-vector-based routing protocol packet and byte counters on the router port for which the entry exists. Reset (2) resets the counters to 0. nwDecIVProtoIfCtrOperationalTime is also reset to 0.
OBJECT-TYPE    
  INTEGER other(1), reset(2)  

nwDecIVProtoIfCtrOperationalTime 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.4
Indicates the elapsed time, in hundredths of a second, that nwDecIVProtoIfCtrAdminStatus has been in the current state.
OBJECT-TYPE    
  TimeTicks  

nwDecIVProtoIfCtrInPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.5
Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been received, during nwDecIVProtoIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVProtoIfCtrOutPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.6
Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been transmitted, during nwDecIVProtoIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVProtoIfCtrFilteredPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.7
Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been administratively filtered, during nwDecIVProtoIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVProtoIfCtrDiscardPkts 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.8
Indicates the total number of DECnet Phase IV distance-vector-based routing protocol packets that have been discarded, during nwDecIVProtoIfCtrOperationalTime, that were received on the router port for which the entry exist.
OBJECT-TYPE    
  Counter  

nwDecIVProtoIfCtrInBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.9
Indicates the total number of bytes in the DECnet Phase IV distance-vector-based routing protocol packets that have been received, during nwDecIVProtoIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVProtoIfCtrOutBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.10
Indicates the total number of bytes in the DECnet Phase IV distance-vector-based routing protocol packets that have been transmitted, during nwDecIVProtoIfCtrOperationalTime, on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVProtoIfCtrFilteredBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.11
Indicates the total number of bytes in the DECnet Phase IV distance-vector-based routing protocol packets that have been administratively filtered, during nwDecIVProtoIfCtrOperationalTime, that were received on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVProtoIfCtrDiscardBytes 1.3.6.1.4.1.52.4.2.2.2.3.3.2.4.1.1.2.2.1.1.12
Indicates the total number of bytes in the DECnet packets that have been discarded, during nwDecIVProtoIfCtrOperationalTime, that were received on the router port for which the entry exists.
OBJECT-TYPE    
  Counter  

nwDecIVFibTable 1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1
This table contains an entry for each route being used to forward DECnet data packets..
OBJECT-TYPE    
  SEQUENCE OF  
    NwDecIVFibEntry

nwDecIVFibEntry 1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1
Each entry in the table describes a route to a particular DECnet destination network and node.
OBJECT-TYPE    
  NwDecIVFibEntry  

nwDecIVFibNodeId 1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.1
Contains the DECnet Address of the destination node of the route for which the entry exists.
OBJECT-TYPE    
  DecIVAddress  

nwDecIVFibNextHopNodeId 1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.2
Contains the DECnet Address of the next hop router for the route for which the entry exists.
OBJECT-TYPE    
  DecIVAddress  

nwDecIVFibNextHopIf 1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.3
Indicates the value of MIB 2 ifindex, which identifies the router port through which the route exists.
OBJECT-TYPE    
  INTEGER  

nwDecIVFibRouteType 1.3.6.1.4.1.52.4.2.2.2.3.3.2.5.1.1.4
Indicates the status of the route. A value of 3 indicates that the destination is on the network segment that is directly connected to the router port identified by nwDecIVFibNextHopIf. A value of 4 indicates that the destination is on an indirectly connected network segment, which is reachable through the next hop router indicated by the value of nwDecIVFibNextHopNodeId. A value of 2 indicates that the route is invalid.
OBJECT-TYPE    
  INTEGER other(1), invalid(2), direct(3), remote(4)  

nwDecIVAclValidEntries 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.1
Indicates the number of valid entries that exist in the access control list table, nwDecIVAclTable.
OBJECT-TYPE    
  Gauge  

nwDecIVAclTable 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2
This table contains the access control list information for DECnet traffic. This table contains entries each of which specifies whether packet forwarding between a particular source destination pair is permitted or denied. Each entry is part of a particular access control list. Each list is identified by a unique Access Control ID. Each list may contain multiple entries ordered by sequence number. When an Access Control List is searched, it is searched in sequence number order and the first match found ends the search. If no match is found, access defaults to permitted.
OBJECT-TYPE    
  SEQUENCE OF  
    NwDecIVAclEntry

nwDecIVAclEntry 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1
Each entry contains DECnet source/destination access information.
OBJECT-TYPE    
  NwDecIVAclEntry  

nwDecIVAclIdentifier 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.1
This is the primary (major) index into the DECnet access control list table. This value identifies each access control list by a unique identifier, a number arbitrarily assigned by the user. All entries that have the same value for nwDecIVAclIdentifier belong to the same access control list.
OBJECT-TYPE    
  INTEGER  

nwDecIVAclSequence 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.2
This is the secondary (minor) index into the DECnet access control list table. This number corresponds to a sequence number used to order multiple entries within the same access control list.
OBJECT-TYPE    
  INTEGER  

nwDecIVAclPermission 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.3
Specifies whether access is allowed or denied between the source and destination address pair. Note that source and destination are interchangeable when bi-directional control is selected. To remove an existing entry set nwDecIVAclPermission to invalid (2). Invalid entries disappear after reboot.
OBJECT-TYPE    
  INTEGER other(1), invalid(2), permit(3), deny(4), permit-bidirectional(5), deny-bidirectional(6)  

nwDecIVAclMatches 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.4
Indicates the number of matches on this entry that have resulted in the permit/deny access restriction being applied as part of the forwarding process.
OBJECT-TYPE    
  Counter  

nwDecIVAclDestAddress 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.5
Specifies the destination DECnet Address used to compare for matches on the access control list. Either the Area ID or Node ID of this address may be set to 0, a wildcard value which matches all areas or all nodes.
OBJECT-TYPE    
  DecIVAddress  

nwDecIVAclSrcAddress 1.3.6.1.4.1.52.4.2.2.2.3.3.2.7.2.1.6
Specifies the source DECnet Address used to compare for matches on the access control list. Either the Area ID or Node ID of this address may be set to a wildcard value which matches all areas or all nodes.
OBJECT-TYPE    
  DecIVAddress  

nwDecIVHostMapTable 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1
The DecIV Address translation table used for mapping a DecIV address to a circuit identifier (if applicable), corresponding port number, and framing type.
OBJECT-TYPE    
  SEQUENCE OF  
    NwDecIVHostMapEntry

nwDecIVHostMapEntry 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1
Each entry contains one DecIVAddress to circuit equivalence. Also provided is the framing required to converse with this host, and the corresponding logical port number.
OBJECT-TYPE    
  NwDecIVHostMapEntry  

nwDecIVHostMapIfIndex 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.1
This is the primary (major) index into the DecIV HostMap table. This number corresponds to the index into the MIB-2 Interfaces Group which describes the DecIV router port for which the entry exists.
OBJECT-TYPE    
  INTEGER  

nwDecIVHostMapDecIVAddr 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.2
The DecIVAddress of the host on the corresponding interface and circuit (if applicable).
OBJECT-TYPE    
  DecIVAddress  

nwDecIVHostMapType 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.3
Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the nwDecIVHostMapTable. That is, it effectively dissasociates the circuitand/or interface identified with said entry from the mapping identified with said entry. It is an implementation- specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper inter- pretation of such entries requires examination of the relevant wDecIVHostMapType object.
OBJECT-TYPE    
  INTEGER other(1), invalid(2), dynamic(3), static(4), inactive(5)  

nwDecIVHostMapCircuitID 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.4
The identifier for the virtual circuit present on the interface. On an interface configured for Frame Relay, this number is the DLCI for the DecIV Address at the end of the circuit. For non-WAN interfaces, the value of this object is zero.
OBJECT-TYPE    
  INTEGER  

nwDecIVHostMapFraming 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.5
Specifies the framing type required to converse with the host for which this entry exists.
OBJECT-TYPE    
  INTEGER other(1), ethernet(2), snap(3), nativewan(8), encapenet(9), encapenetsnap(11), encaptrsnap(14), encapfddisnap(16), canonical(17)  

nwDecIVHostMapPortNumber 1.3.6.1.4.1.52.4.2.2.2.3.3.2.6.3.1.1.6
The unique value for the logical port number. It's value ranges between 1 and a maximum value which is dependent on both the number of configured interfaces in the system and the number of circuits present on those interfaces which are of WAN type.
OBJECT-TYPE    
  INTEGER  

nwDecIVEventAdminStatus 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.1.1
Sets the administrative state of DECnet event logging. Enabled (3) causes the event log to become active. Disabled (2) causes the event log to become inactive.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwDecIVEventMaxEntries 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.1.2
Sets the maximum number of entries allowed in the event log table. When the number of entries reaches the value of nwDecIVEventMaxEntries, the first (oldest) entry is deleted to allow a new entry to be added.
OBJECT-TYPE    
  INTEGER  

nwDecIVEventTraceAll 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.1.3
Enabled (3) allows logging of all event types on all router ports for all protocols and components. Disabled (2) causes the filter table to specify which events to log.
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

nwDecIVEventFilterTable 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1
This table contains and entry for each event filter configured for DECnet Phase IV Routing Services events.
OBJECT-TYPE    
  SEQUENCE OF  
    NwDecIVEventFilterEntry

nwDecIVEventFilterEntry 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1
Each entry describes an event filter which defines a particular type of event to be logged to the event log. The value of nwDecIVEventFltrProtocol indicates the value used either in the nwRtgProtocolTable or the nwComponentTable in the Cabletron Routing Services MIB, which identifies the protocol or component to which the entry applies.
OBJECT-TYPE    
  NwDecIVEventFilterEntry  

nwDecIVEventFltrProtocol 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.1
Indicates the value of the Cabletron Routing Services MIB nwRtgProtocolInstance or nwComponentRtgInstance which identifies the protocol involved in the event for which the event filter exists.
OBJECT-TYPE    
  INTEGER  

nwDecIVEventFltrIfNum 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.2
Specifies the router port involved in the event for which the event filter exists.
OBJECT-TYPE    
  INTEGER  

nwDecIVEventFltrControl 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.3
Set this value to 3 to add the entry to the event filter table. Set this value to 2 to remove the entry from the event filter table.
OBJECT-TYPE    
  INTEGER other(1), delete(2), add(3)  

nwDecIVEventFltrType 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.4
This 6 bit mask specifies the types of events to be logged. By default all 6 bits are set to 1, indicating that all types of events are to be logged. Setting any bit to 0 removes an event type from this field and prevents that type of event from being logged. Setting any bit to 1 adds an event type to this field and enables that type of event to be logged.
OBJECT-TYPE    
  INTEGER misc(1), timer(2), rcv(4), xmit(8), event(16), diags(32), error(64)  

nwDecIVEventFltrSeverity 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.5
Specifies the level of severity an event must meet in order to be logged. Controls the amount of event logging by ignoring events of a lower priority than specified by this filter value. `Highmed' ignores only events of the lowest severity. `Highlow' logs all events highest priority through lowest. `Highest' severity causes all events except those of the highest severity to be ignored. `Highmed' severity is the default setting which causes only events of the lowest severity to be ignored. `Highlow' severity logs all events, regardless of severity.
OBJECT-TYPE    
  INTEGER highest(1), highmed(2), highlow(3)  

nwDecIVEventFltrAction 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.2.1.1.6
Specifies how the events are to be logged. Logging to the `log' stores the events in the event log table (nwDecIVEventLogTable). Logging to'trap' sends events out through the trap mechanism.
OBJECT-TYPE    
  INTEGER log(1), trap(2), log-trap(3)  

nwDecIVEventTable 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1
This table contains an entry for each event that has been logged.
OBJECT-TYPE    
  SEQUENCE OF  
    NwDecIVEventEntry

nwDecIVEventEntry 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1
Each entry contains the information about an event that has been logged to the event table.
OBJECT-TYPE    
  NwDecIVEventEntry  

nwDecIVEventNumber 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.1
An ordinal value assigned to the event for which the log entry exists. nwDecIVEventNumber is assigned so that each event in the event log can be uniquely identified by the value of nwDecIVEventNumber.
OBJECT-TYPE    
  INTEGER  

nwDecIVEventTime 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.2
Indicates the time at which the event was logged to the event log.
OBJECT-TYPE    
  TimeTicks  

nwDecIVEventType 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.3
Indicates the type of event that was logged.
OBJECT-TYPE    
  INTEGER misc(1), timer(2), rcv(4), xmit(8), event(16), error(32)  

nwDecIVEventSeverity 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.4
Indicates the severity that was assigned to the event.
OBJECT-TYPE    
  INTEGER highest(1), highmed(2), highlow(3)  

nwDecIVEventProtocol 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.5
Indicates the value of the Cabletron Routing Services MIB nwRtgProtocolInstance or nwComponentInstance which identifies the protocol or component that was involved in the event.
OBJECT-TYPE    
  INTEGER  

nwDecIVEventIfNum 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.6
Indicates the router port that was involved in the event.
OBJECT-TYPE    
  INTEGER  

nwDecIVEventTextString 1.3.6.1.4.1.52.4.2.2.2.3.3.2.10.3.1.1.7
Contains the actual text string that was logged.
OBJECT-TYPE    
  STRING