CTRON-BRIDGE-MIB

File: CTRON-BRIDGE-MIB.mib (78157 bytes)

Imported modules

RFC-1212 RFC1213-MIB BRIDGE-MIB
CTRON-MIB-NAMES RFC1155-SMI

Imported symbols

OBJECT-TYPE DisplayString BridgeId
ctBridge Counter TimeTicks

Defined Types

CtPvstStpEntry  
SEQUENCE    
  ctPvstStpVlanId INTEGER
  ctPvstStpProtocolSpecification INTEGER
  ctPvstStpPriority INTEGER
  ctPvstStpTimeSinceTopologyChange TimeTicks
  ctPvstStpTopChanges Counter
  ctPvstStpDesignatedRoot BridgeId
  ctPvstStpRootCost INTEGER
  ctPvstStpRootPort INTEGER
  ctPvstStpMaxAge INTEGER
  ctPvstStpHelloTime INTEGER
  ctPvstStpHoldTime INTEGER
  ctPvstStpForwardDelay INTEGER
  ctPvstStpBridgeMaxAge INTEGER
  ctPvstStpBridgeHelloTime INTEGER
  ctPvstStpBridgeForwardDelay INTEGER

CtPvstStpPortEntry  
SEQUENCE    
  ctPvstStpPortVlanId INTEGER
  ctPvstStpPort INTEGER
  ctPvstStpPortPriority INTEGER
  ctPvstStpPortState INTEGER
  ctPvstStpPortEnable INTEGER
  ctPvstStpPortPathCost INTEGER
  ctPvstStpPortDesignatedRoot BridgeId
  ctPvstStpPortDesignatedCost INTEGER
  ctPvstStpPortDesignatedBridge BridgeId
  ctPvstStpPortDesignatedPort OCTET STRING
  ctPvstStpPortForwardTransitions Counter

CtBridgeSrPortPairEntry  
SEQUENCE    
  ctBridgeSrPortPairSrcPort INTEGER
  ctBridgeSrPortPairDestPort INTEGER
  ctBridgeSrPortPairPackets Counter
  ctBridgeSrPortPairState INTEGER

CtBridgeTpPortPairEntry  
SEQUENCE    
  ctBridgeTpPortPairSrcPort INTEGER
  ctBridgeTpPortPairDestPort INTEGER
  ctBridgeTpPortPairPackets Counter
  ctBridgeTpPortPairState INTEGER

CtBridgeSdbEnetEntry  
SEQUENCE    
  ctBridgeSdbEnetFtrNo INTEGER
  ctBridgeSdbEnetState INTEGER
  ctBridgeSdbEnetFtrData DisplayString
  ctBridgeSdbEnetDataOffset INTEGER

CtBridgeSdbEnetIOEntry  
SEQUENCE    
  ctBridgeSdbEnetIOFtrNo INTEGER
  ctBridgeSdbEnetIORcvPort INTEGER
  ctBridgeSdbEnetIOAllowedToGoTo OCTET STRING
  ctBridgeSdbEnetIODelEntry INTEGER

CtBridgeSdbTrEntry  
SEQUENCE    
  ctBridgeSdbTrFtrNo INTEGER
  ctBridgeSdbTrState INTEGER
  ctBridgeSdbTrFtrData DisplayString
  ctBridgeSdbTrDataOffset INTEGER

CtBridgeSdbTrIOEntry  
SEQUENCE    
  ctBridgeSdbTrIOFtrNo INTEGER
  ctBridgeSdbTrIORcvPort INTEGER
  ctBridgeSdbTrIOAllowedToGoTo OCTET STRING
  ctBridgeSdbTrIODelEntry INTEGER

CtBridgeTransTrEnetIBMEntry  
SEQUENCE    
  ctBridgeTransTrEnetIBMIndex INTEGER
  ctBridgeTransTrEnetIBMSap OCTET STRING
  ctBridgeTransTrEnetIBMState INTEGER

CtBridgeTransTrEnetSnapEntry  
SEQUENCE    
  ctBridgeTransTrEnetSnapIndex INTEGER
  ctBridgeTransTrEnetSnapType OCTET STRING
  ctBridgeTransTrEnetSnapState INTEGER

CtBridgeSdbGenericEntry  
SEQUENCE    
  ctBridgeSdbGenericFtrNo INTEGER
  ctBridgeSdbGenericState INTEGER
  ctBridgeSdbGenericFtrData DisplayString
  ctBridgeSdbGenericDataOffset INTEGER
  ctBridgeSdbGenericFilterType INTEGER

CtBridgeSdbGenericIOEntry  
SEQUENCE    
  ctBridgeSdbGenericIOFtrNo INTEGER
  ctBridgeSdbGenericIORcvPort INTEGER
  ctBridgeSdbGenericIOAllowedToGoTo OCTET STRING
  ctBridgeSdbGenericIODelEntry INTEGER

CtBridgeLoadShareInstanceEntry  
SEQUENCE    
  ctBridgeLoadShareInstanceId INTEGER
  ctBridgeLoadShareAdminStatus INTEGER
  ctBridgeLoadShareOperStatus INTEGER

CtBridgeLoadSharePortEntry  
SEQUENCE    
  ctBridgeLoadSharePortNum INTEGER
  ctBridgeLoadSharePortInstanceId INTEGER
  ctBridgeLoadSharePortAdminStatus INTEGER
  ctBridgeLoadSharePortOperStatus INTEGER
  ctBridgeLoadSharePortForwardMask INTEGER
  ctBridgeLoadSharePortForwardInstance INTEGER
  ctBridgeLoadSharePortNumPorts INTEGER

Defined Values

ctBridgeStp 1.3.6.1.4.1.52.4.1.2.3.2
OBJECT IDENTIFIER    

ctBridgeSr 1.3.6.1.4.1.52.4.1.2.3.3
OBJECT IDENTIFIER    

ctBridgeTp 1.3.6.1.4.1.52.4.1.2.3.4
OBJECT IDENTIFIER    

ctBridgeSdbEnet 1.3.6.1.4.1.52.4.1.2.3.5
OBJECT IDENTIFIER    

ctBridgeSdbTr 1.3.6.1.4.1.52.4.1.2.3.6
OBJECT IDENTIFIER    

ctBridgeTransTrEnet 1.3.6.1.4.1.52.4.1.2.3.7
OBJECT IDENTIFIER    

ctBridgeExtendedControl 1.3.6.1.4.1.52.4.1.2.3.8
OBJECT IDENTIFIER    

ctBridgeSdbGeneric 1.3.6.1.4.1.52.4.1.2.3.9
OBJECT IDENTIFIER    

ctBridgeLoadShare 1.3.6.1.4.1.52.4.1.2.3.10
OBJECT IDENTIFIER    

ctBridgeStpProtocolSpecification 1.3.6.1.4.1.52.4.1.2.3.2.1
This object allows the network manager to select which Spanning Tree Protocol will be operational on the bridge. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. The value 'ieee8021d(3)' indicates the IEEE 802.1d Spanning Tree Protocol. The value 'none(1)' indicates no Spanning Tree Protocol is operational.
OBJECT-TYPE    
  INTEGER none(1), decLb100(2), ieee8021d(3)  

ctBridgePvst 1.3.6.1.4.1.52.4.1.2.3.2.2
OBJECT IDENTIFIER    

ctPvstStpMode 1.3.6.1.4.1.52.4.1.2.3.2.2.1
Specifies whether the switch is in 802.1D/Q single spanning tree mode, or PVST mode. If the switch is configured with PVST information for some VLANs, setting this object to dot1qMode(1) will cause it to ignore the PVST settings and move all VLANs into the single 802.1Q spanning tree.
OBJECT-TYPE    
  INTEGER dot1qMode(1), pvstMode(2)  

ctPvstMaxNumStp 1.3.6.1.4.1.52.4.1.2.3.2.2.2
Returns maximum number of spanning trees that this device can implement. This will limit the number of VLANs that can be configured with distinct spanning trees.
OBJECT-TYPE    
  INTEGER 1..4094  

ctPvstNumStps 1.3.6.1.4.1.52.4.1.2.3.2.2.3
When read, this returns the number of PVST spanning trees active in the switch, which should correspond to the number of entries in ctPvstStpTable. When written with 4094, it should create a spanning tree for each currently configured VLAN. If a switch cannot create as many spanning trees as configured VLANs, this write should return an error. Writing any value other than 4094 should return an error.
OBJECT-TYPE    
  INTEGER 1..4094  

ctPvstLastTopologyChange 1.3.6.1.4.1.52.4.1.2.3.2.2.4
This summary object contains the value of sysUpTime when any of the rows in ctPvstStpTable last incremented ctPvstStpTopChanges. Poll this object to determine if any of the STP instances had topology changes.
OBJECT-TYPE    
  TimeTicks  

ctPvstStpTable 1.3.6.1.4.1.52.4.1.2.3.2.2.5
A collection of spanning tree objects per VLAN.
OBJECT-TYPE    
  SEQUENCE OF  
    CtPvstStpEntry

ctPvstStpEntry 1.3.6.1.4.1.52.4.1.2.3.2.2.5.1
An entry related to a specific spanning tree.
OBJECT-TYPE    
  CtPvstStpEntry  

ctPvstStpVlanId 1.3.6.1.4.1.52.4.1.2.3.2.2.5.1.1
The VLAN-ID of the VLAN on which this spanning tree is running. Writing a VLAN-ID will create a separate spanning tree for that VLAN, if it previously was part of the single 802.1Q VLAN.
OBJECT-TYPE    
  INTEGER 1..4094  

ctPvstStpProtocolSpecification 1.3.6.1.4.1.52.4.1.2.3.2.2.5.1.2
An indication of what version of the Spanning Tree Protocol is being run. The value 'decLb100(2)' indicates the DEC LANbridge 100 Spanning Tree protocol. IEEE 802.1d implementations will return 'ieee8021d(3)'. If future versions of the IEEE Spanning Tree Protocol are released that are incompatible with the current version a new value will be defined.
OBJECT-TYPE    
  INTEGER unknown(1), decLb100(2), ieee8021d(3)  

ctPvstStpPriority 1.3.6.1.4.1.52.4.1.2.3.2.2.5.1.3
The value of the write-able portion of the Bridge ID, i.e., the first two octets of the (8 octet long) Bridge ID.
OBJECT-TYPE    
  INTEGER 0..65535  

ctPvstStpTimeSinceTopologyChange 1.3.6.1.4.1.52.4.1.2.3.2.2.5.1.4
The time (in hundredths of a second) since the last time a topology change was detected by the bridge entity.
OBJECT-TYPE    
  TimeTicks  

ctPvstStpTopChanges 1.3.6.1.4.1.52.4.1.2.3.2.2.5.1.5
The total number of topology changes detected by this bridge since the management entity was last reset or initialized.
OBJECT-TYPE    
  Counter  

ctPvstStpDesignatedRoot 1.3.6.1.4.1.52.4.1.2.3.2.2.5.1.6
The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node.
OBJECT-TYPE    
  BridgeId  

ctPvstStpRootCost 1.3.6.1.4.1.52.4.1.2.3.2.2.5.1.7
The cost of the path to the root as seen from this bridge.
OBJECT-TYPE    
  INTEGER  

ctPvstStpRootPort 1.3.6.1.4.1.52.4.1.2.3.2.2.5.1.8
The port number of the port which offers the lowest cost path from this bridge to the root bridge.
OBJECT-TYPE    
  INTEGER  

ctPvstStpMaxAge 1.3.6.1.4.1.52.4.1.2.3.2.2.5.1.9
The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using.
OBJECT-TYPE    
  INTEGER  

ctPvstStpHelloTime 1.3.6.1.4.1.52.4.1.2.3.2.2.5.1.10
The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using.
OBJECT-TYPE    
  INTEGER  

ctPvstStpHoldTime 1.3.6.1.4.1.52.4.1.2.3.2.2.5.1.11
This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.
OBJECT-TYPE    
  INTEGER  

ctPvstStpForwardDelay 1.3.6.1.4.1.52.4.1.2.3.2.2.5.1.12
This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. [Note that this value is the one that this bridge is currently using, in contrast to ctPvstStpBridgeForwardDelay which is the value that this bridge and all others would start using if/when this bridge were to become the root.]
OBJECT-TYPE    
  INTEGER  

ctPvstStpBridgeMaxAge 1.3.6.1.4.1.52.4.1.2.3.2.2.5.1.13
The value that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of ctPvstStpBridgeHelloTime. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
OBJECT-TYPE    
  INTEGER 600..4000  

ctPvstStpBridgeHelloTime 1.3.6.1.4.1.52.4.1.2.3.2.2.5.1.14
The value that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D- 1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
OBJECT-TYPE    
  INTEGER 100..1000  

ctPvstStpBridgeForwardDelay 1.3.6.1.4.1.52.4.1.2.3.2.2.5.1.15
The value that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the value of ctPvstStpBridgeMaxAge. The granularity of this timer is specified by 802.1D-1990 to be 1 second. An agent may return a badValue error if a set is attempted to a value which is not a whole number of seconds.
OBJECT-TYPE    
  INTEGER 400..3000  

ctPvstStpPortTable 1.3.6.1.4.1.52.4.1.2.3.2.2.6
A collection of per-port spanning tree objects per VLAN.
OBJECT-TYPE    
  SEQUENCE OF  
    CtPvstStpPortEntry

ctPvstStpPortEntry 1.3.6.1.4.1.52.4.1.2.3.2.2.6.1
A port entry related to a specific spanning tree. Only ports which are in a VLAN which is running a PVST should be reported for that VLAN.
OBJECT-TYPE    
  CtPvstStpPortEntry  

ctPvstStpPortVlanId 1.3.6.1.4.1.52.4.1.2.3.2.2.6.1.1
The VLAN-ID of the VLAN on which this spanning tree is running.
OBJECT-TYPE    
  INTEGER 1..4094  

ctPvstStpPort 1.3.6.1.4.1.52.4.1.2.3.2.2.6.1.2
The port number of the port for which this entry contains Spanning Tree Protocol management information.
OBJECT-TYPE    
  INTEGER 1..65535  

ctPvstStpPortPriority 1.3.6.1.4.1.52.4.1.2.3.2.2.6.1.3
The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID. The other octet of the Port ID is given by the value of ctPvstStpPort.
OBJECT-TYPE    
  INTEGER 0..255  

ctPvstStpPortState 1.3.6.1.4.1.52.4.1.2.3.2.2.6.1.4
The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame. If the bridge has detected a port that is malfunctioning it will place that port into the broken(6) state. For ports which are disabled (see ctPvstStpPortEnable), this object will have a value of disabled(1).
OBJECT-TYPE    
  INTEGER disabled(1), blocking(2), listening(3), learning(4), forwarding(5), broken(6)  

ctPvstStpPortEnable 1.3.6.1.4.1.52.4.1.2.3.2.2.6.1.5
The enabled/disabled status of the port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctPvstStpPortPathCost 1.3.6.1.4.1.52.4.1.2.3.2.2.6.1.6
The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 802.1D-1990 recommends that the default value of this parameter be in inverse proportion to the speed of the attached LAN.
OBJECT-TYPE    
  INTEGER 1..65535  

ctPvstStpPortDesignatedRoot 1.3.6.1.4.1.52.4.1.2.3.2.2.6.1.7
The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
OBJECT-TYPE    
  BridgeId  

ctPvstStpPortDesignatedCost 1.3.6.1.4.1.52.4.1.2.3.2.2.6.1.8
The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
OBJECT-TYPE    
  INTEGER  

ctPvstStpPortDesignatedBridge 1.3.6.1.4.1.52.4.1.2.3.2.2.6.1.9
The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
OBJECT-TYPE    
  BridgeId  

ctPvstStpPortDesignatedPort 1.3.6.1.4.1.52.4.1.2.3.2.2.6.1.10
The Port Identifier of the port on the Designated Bridge for this port's segment.
OBJECT-TYPE    
  OCTET STRING Size(2)  

ctPvstStpPortForwardTransitions 1.3.6.1.4.1.52.4.1.2.3.2.2.6.1.11
The number of times this port has transitioned from the Learning state to the Forwarding state.
OBJECT-TYPE    
  Counter  

ctBridgeSrPortPairTable 1.3.6.1.4.1.52.4.1.2.3.3.1
A table containing information of source and destination port pairs for source routing.
OBJECT-TYPE    
  SEQUENCE OF  
    CtBridgeSrPortPairEntry

ctBridgeSrPortPairEntry 1.3.6.1.4.1.52.4.1.2.3.3.1.1
An entry consisting of objects specifying information for the source and destination port pairs used for source routing.
OBJECT-TYPE    
  CtBridgeSrPortPairEntry  

ctBridgeSrPortPairSrcPort 1.3.6.1.4.1.52.4.1.2.3.3.1.1.1
The source port (ie the port which received the packets) for which this entry has source routing information.
OBJECT-TYPE    
  INTEGER  

ctBridgeSrPortPairDestPort 1.3.6.1.4.1.52.4.1.2.3.3.1.1.2
The destination port (ie the port which transmitted the packets) for which this entry has source routing information.
OBJECT-TYPE    
  INTEGER  

ctBridgeSrPortPairPackets 1.3.6.1.4.1.52.4.1.2.3.3.1.1.3
The number of packets forward by the source route bridge from the SrcPort to the DestPort.
OBJECT-TYPE    
  Counter  

ctBridgeSrPortPairState 1.3.6.1.4.1.52.4.1.2.3.3.1.1.4
The state of source route bridging on this port pair. This is the desired state of the administrator. The operational state of the port pair is determined by this state along with the states of dot1dStpPortState within the IETF Bridge MIB and ifOperStatus of the IETF MIB II for each port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctBridgeSrConfigPortType 1.3.6.1.4.1.52.4.1.2.3.3.2
This object selects the type of Bridging performed on a given bridge port. It is used by the bridge to determine if conversion from a Source Routing packet to a Transparent packet or vice verse is required.
OBJECT-TYPE    
  INTEGER transparentonly(1), sourcerouteonly(2), srt(3)  

ctBridgeTpPortPairTable 1.3.6.1.4.1.52.4.1.2.3.4.1
A table containing information of source and destination port pairs for transparent MAC briding.
OBJECT-TYPE    
  SEQUENCE OF  
    CtBridgeTpPortPairEntry

ctBridgeTpPortPairEntry 1.3.6.1.4.1.52.4.1.2.3.4.1.1
An entry consisting of objects specifying information for the source and destination port pairs used for transparent bridging.
OBJECT-TYPE    
  CtBridgeTpPortPairEntry  

ctBridgeTpPortPairSrcPort 1.3.6.1.4.1.52.4.1.2.3.4.1.1.1
The source port (ie the port which received the packets) for which this entry has transparent bridge information.
OBJECT-TYPE    
  INTEGER  

ctBridgeTpPortPairDestPort 1.3.6.1.4.1.52.4.1.2.3.4.1.1.2
The destination port (ie the port which the packets were transmitted out) for which this entry has transparent bridge information.
OBJECT-TYPE    
  INTEGER  

ctBridgeTpPortPairPackets 1.3.6.1.4.1.52.4.1.2.3.4.1.1.3
The number of packets transparently forwarded by the bridge from the SrcPort to the DestPort.
OBJECT-TYPE    
  Counter  

ctBridgeTpPortPairState 1.3.6.1.4.1.52.4.1.2.3.4.1.1.4
The state of transparent bridging on this port pair. This is the desired state of the administrator. The operational state of the port pair is determined by this state along with the states of dot1dStpPortState within the IETF Bridge MIB and ifOperStatus of the IETF MIB II for each port.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctBridgeSdbEnetTotFtrs 1.3.6.1.4.1.52.4.1.2.3.5.1
The total number of Ethernet filters in the special database.
OBJECT-TYPE    
  INTEGER  

ctBridgeSdbEnetNoMatch 1.3.6.1.4.1.52.4.1.2.3.5.2
The process to be performed if no match is found in the Ethernet special database. The process of filtering or forwarding is for all ports. searchFDB results in searching the IEEE 802.1D transparent filter database referenced by the IETF Bridge MIB.
OBJECT-TYPE    
  INTEGER filter(1), forward(2), searchFDB(3)  

ctBridgeSdbEnetTable 1.3.6.1.4.1.52.4.1.2.3.5.3
A table containing filtering information configured into the bridge by (local or network) management specifying the specific packet string (destination address, source address, type/length field as well as a window of 64 bytes of packet data beginning at a data offset) to be used for filtering decisions. The filters are to be searched in the order of incrementing filter number.
OBJECT-TYPE    
  SEQUENCE OF  
    CtBridgeSdbEnetEntry

ctBridgeSdbEnetEntry 1.3.6.1.4.1.52.4.1.2.3.5.3.1
Filtering information which extends the filtering capability of IEEE 802.1d.
OBJECT-TYPE    
  CtBridgeSdbEnetEntry  

ctBridgeSdbEnetFtrNo 1.3.6.1.4.1.52.4.1.2.3.5.3.1.1
The Filter number for which this entry contains filtering information.
OBJECT-TYPE    
  INTEGER  

ctBridgeSdbEnetState 1.3.6.1.4.1.52.4.1.2.3.5.3.1.2
The state of the filter for which this entry contains filtering information.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctBridgeSdbEnetFtrData 1.3.6.1.4.1.52.4.1.2.3.5.3.1.3
The specific packet string representing the destination address, source address, type/length field and a window of 64 bytes of packet data beginning at DataOffset to be used for filtering decisions. Each ASCII character of the string represents a nibble of packet data, therefore the packet string should be (14+64) * 2 = 156 characters long. A value of 'x' in the packet string is used to indicate a 'Don't care' and no filtering is to be performed on that nibble. The string may be be of size 0 to 78 bytes. If a size less than 78 bytes is used, the string will still begin at the destination address.
OBJECT-TYPE    
  DisplayString Size(0..78)  

ctBridgeSdbEnetDataOffset 1.3.6.1.4.1.52.4.1.2.3.5.3.1.4
The offset into a packet from which the bridge begins its filtering decisions on the 64 byte data window. The value '0' indicates that the window begins at the first byte after the Ethernet MAC header. The largest value of DataOffset is max_Enet_pkt - MAC header - window - 1 (1514 - 14 - 64 - 1 = 1435).
OBJECT-TYPE    
  INTEGER  

ctBridgeSdbEnetIOTable 1.3.6.1.4.1.52.4.1.2.3.5.4
A table containing the set of ports to which frames received from specific ports and containing the specific packet string (destination address, source address, type/length field as well as a window of 64 bytes of packet data beginning at a data offset) of the corresponding filter number of SdbEnetTable are allowed to be forwarded. The value of '0' in this table as the RcvPort is used to specify all ports which are not already specified in this table for a particular entry.
OBJECT-TYPE    
  SEQUENCE OF  
    CtBridgeSdbEnetIOEntry

ctBridgeSdbEnetIOEntry 1.3.6.1.4.1.52.4.1.2.3.5.4.1
The set of ports to which frames received by the RcvPort and containing the specific packet string of the corresponding filter number of SdbEnetTable are allowed to be forwarded.
OBJECT-TYPE    
  CtBridgeSdbEnetIOEntry  

ctBridgeSdbEnetIOFtrNo 1.3.6.1.4.1.52.4.1.2.3.5.4.1.1
The Filter number for which this entry contains filtering information.
OBJECT-TYPE    
  INTEGER  

ctBridgeSdbEnetIORcvPort 1.3.6.1.4.1.52.4.1.2.3.5.4.1.2
Either the value '0', or the port number of the port from which a frame must be received in order for this entry's filtering information to apply. A value of '0' indicates that this entry applies on all ports of the bridge for which there is no other applicable entry.
OBJECT-TYPE    
  INTEGER  

ctBridgeSdbEnetIOAllowedToGoTo 1.3.6.1.4.1.52.4.1.2.3.5.4.1.3
The set of ports to which frames received from a specific port and containing the specific packet string of the corresponding filter number are allowed to be forwarded. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. (Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant.)
OBJECT-TYPE    
  OCTET STRING  

ctBridgeSdbEnetIODelEntry 1.3.6.1.4.1.52.4.1.2.3.5.4.1.4
Writing a '1' to this object deletes this entry from the Ethernet special database. This object will always return a '1' when read.
OBJECT-TYPE    
  INTEGER deleteEntry(1)  

ctBridgeSdbTrTotFtrs 1.3.6.1.4.1.52.4.1.2.3.6.1
The total number of Token Ring filters in the special database.
OBJECT-TYPE    
  INTEGER  

ctBridgeSdbTrNoMatch 1.3.6.1.4.1.52.4.1.2.3.6.2
The process to be performed if no match is found in the Token Ring special database. The process of filtering or forwarding is for all ports. searchFDB results in searching the IEEE 802.1D transparent filter database referenced by the IETF Bridge MIB.
OBJECT-TYPE    
  INTEGER filter(1), forward(2), searchFDB(3)  

ctBridgeSdbTrTable 1.3.6.1.4.1.52.4.1.2.3.6.3
A table containing filtering information configured into the bridge by (local or network) management specifying the specific packet string (AC, FC, destination address, source address, as well as a window of 64 bytes of packet data beginning at a data offset) to be used for filtering decisions. The filters are to be searched in the order of incrementing filter number.
OBJECT-TYPE    
  SEQUENCE OF  
    CtBridgeSdbTrEntry

ctBridgeSdbTrEntry 1.3.6.1.4.1.52.4.1.2.3.6.3.1
Filtering information which extends the filtering capability of IEEE 802.1d.
OBJECT-TYPE    
  CtBridgeSdbTrEntry  

ctBridgeSdbTrFtrNo 1.3.6.1.4.1.52.4.1.2.3.6.3.1.1
The Filter number for which this entry contains filtering information.
OBJECT-TYPE    
  INTEGER  

ctBridgeSdbTrState 1.3.6.1.4.1.52.4.1.2.3.6.3.1.2
The state of the filter for which this entry contains filtering information.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctBridgeSdbTrFtrData 1.3.6.1.4.1.52.4.1.2.3.6.3.1.3
The specific packet string consisting of the AC, FC, destination address, source address, and a window of 64 bytes of packet data beginning at DataOffset to be used for filtering decisions. Each ASCII character of the string represents a nibble of packet data, therefore the packet string should be (14+64) * 2 = 156 characters long. A value of 'x' in the packet string is used to indicate a 'Don't care' and no filtering is to be performed on that nibble. If a size less than 78 bytes is used, the string will still begin at the AC field.
OBJECT-TYPE    
  DisplayString Size(0..78)  

ctBridgeSdbTrDataOffset 1.3.6.1.4.1.52.4.1.2.3.6.3.1.4
The offset into a packet from which the bridge begins its filtering decisions on the 64 byte data window. The value '0' indicates that the window begins at the first byte after the Token Ring MAC header. The largest value of DataOffset is max_TR_pkt - MAC header - window - 1 (17800 - 14 - 64 - 1 = 17721).
OBJECT-TYPE    
  INTEGER  

ctBridgeSdbTrIOTable 1.3.6.1.4.1.52.4.1.2.3.6.4
A table containing the set of ports to which frames received from specific ports and containing the specific packet string (AC, FC, destination address, source address, as well as a window of 64 bytes of packet data beginning at a data offset) of the corresponding filter number of SdbTrTable are allowed to be forwarded. The value of '0' in this table as the RcvPort is used to specify all ports which are not already specified in this table for a particular entry.
OBJECT-TYPE    
  SEQUENCE OF  
    CtBridgeSdbTrIOEntry

ctBridgeSdbTrIOEntry 1.3.6.1.4.1.52.4.1.2.3.6.4.1
The set of ports to which frames received by the RcvPort and containing the specific packet string of the corresponding filter number of SdbTrTable are allowed to be forwarded.
OBJECT-TYPE    
  CtBridgeSdbTrIOEntry  

ctBridgeSdbTrIOFtrNo 1.3.6.1.4.1.52.4.1.2.3.6.4.1.1
The Filter number for which this entry contains filtering information.
OBJECT-TYPE    
  INTEGER  

ctBridgeSdbTrIORcvPort 1.3.6.1.4.1.52.4.1.2.3.6.4.1.2
Either the value '0', or the port number of the port from which a frame must be received in order for this entry's filtering information to apply. A value of '0' indicates that this entry applies on all ports of the bridge for which there is no other applicable entry.
OBJECT-TYPE    
  INTEGER  

ctBridgeSdbTrIOAllowedToGoTo 1.3.6.1.4.1.52.4.1.2.3.6.4.1.3
The set of ports to which frames received from a specific port and containing the specific packet string of the corresponding filter number are allowed to be forwarded. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. (Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant.)
OBJECT-TYPE    
  OCTET STRING  

ctBridgeSdbTrIODelEntry 1.3.6.1.4.1.52.4.1.2.3.6.4.1.4
Writing a '1' to this object deletes this entry from the Token Ring special database. This object will always return a '1' when read.
OBJECT-TYPE    
  INTEGER deleteEntry(1)  

ctBridgeTransTrEnetAutoMode 1.3.6.1.4.1.52.4.1.2.3.7.1
This object selects whether the auto translation mode is enabled. Auto translation means a bridge learns, from the CSMA/CD ports, which frame format (ie Ethernet or IEEE 802.3 w/snap) a source address is using. Subsequently, the bridge will translate a Token Ring packet, destined to the learned address, with the learned format.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctBridgeTransTrEnetDualMode 1.3.6.1.4.1.52.4.1.2.3.7.2
This object selects whether dual mode is enabled. Dual mode means a bridge translates a Token Ring broadcast or multicast packet to both CSMA/CD frame formats (ie Ethernet and IEEE 802.3 w/snap) when the format has not previously been learned.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctBridgeTransTrEnetNovell 1.3.6.1.4.1.52.4.1.2.3.7.3
This object selects the CSMA/CD frame format (ie Ethernet or IEEE 802.3 w/snap) to which the bridge translates a Novell Token Ring packet. This selection is overidden by the learned format when ctBridgeTransTrEnetAutoMode is enabled and the format has been learned.
OBJECT-TYPE    
  INTEGER ethernet(1), ieee8023snap(2)  

ctBridgeTransTrEnetIP 1.3.6.1.4.1.52.4.1.2.3.7.4
This object selects the CSMA/CD frame format (ie Ethernet or IEEE 802.3 w/snap) to which the bridge translates an IP Token Ring packet including ARP packets. This selection is overidden by the learned format when ctBridgeTransTrEnetAutoMode is enabled and the format has been learned.
OBJECT-TYPE    
  INTEGER ethernet(1), ieee8023snap(2)  

ctBridgeTransTrEnetAARP 1.3.6.1.4.1.52.4.1.2.3.7.5
This object selects the CSMA/CD frame format (ie Ethernet or IEEE 802.3 w/snap) to which the bridge translates an Appletalk ARP Token Ring packet. This selection is overidden by the learned format when ctBridgeTransTrEnetAutoMode is enabled and the format has been learned.
OBJECT-TYPE    
  INTEGER ethernet(1), ieee8023snap(2)  

ctBridgeTransTrEnetNovAdd 1.3.6.1.4.1.52.4.1.2.3.7.6
This object selects the bit ordering of the Hardware Addresses located in the 'data field' of a Token Ring NOVELL packet. The 'data field' includes all bytes of the packet excluding the MAC Header and CRC. The Hardware Addresses in the MAC Header are always MSB for Token Ring packets. The default value is 2.
OBJECT-TYPE    
  INTEGER msb(1), lsb(2)  

ctBridgeTransTrEnetIBMTable 1.3.6.1.4.1.52.4.1.2.3.7.7
A table containing SAP (Service Access Point) values of IBM protocols that the bridge will translate from Token Ring (802.5 w/o snap) to Ethernet.
OBJECT-TYPE    
  SEQUENCE OF  
    CtBridgeTransTrEnetIBMEntry

ctBridgeTransTrEnetIBMEntry 1.3.6.1.4.1.52.4.1.2.3.7.7.1
This entry contains the SAP value of an IBM protocol that is to be translated to Ethernet. The value of the Ethernet type field used in the translation is 80D5. Only SAP values whose entry is enabled will be translated to Ethernet. All other Token Ring packets not having a snap will be translated as an 802.3/802.2 formatted packet.
OBJECT-TYPE    
  CtBridgeTransTrEnetIBMEntry  

ctBridgeTransTrEnetIBMIndex 1.3.6.1.4.1.52.4.1.2.3.7.7.1.1
The index of an entry in the Token Ring to Ethernet Translation table for IBM protocols. The index ranges from 1 to 20.
OBJECT-TYPE    
  INTEGER  

ctBridgeTransTrEnetIBMSap 1.3.6.1.4.1.52.4.1.2.3.7.7.1.2
The SAP value of an IBM protocol. The bridge will translate all Token Ring/802.5 packets without a snap header having this SAP value to Ethernet packets with the Ethernet type field set to 80D5. The SAP value is one octet.
OBJECT-TYPE    
  OCTET STRING  

ctBridgeTransTrEnetIBMState 1.3.6.1.4.1.52.4.1.2.3.7.7.1.3
The state of this entry. A value of 2 indicates that this entry will not be used in the bridge's translation decisions.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctBridgeTransTrEnetSnapFormat 1.3.6.1.4.1.52.4.1.2.3.7.8
This object selects the CSMA/CD frame format (ie Ethernet or IEEE 802.3 w/snap) to which the bridge translates all Token Ring packets with a snap header whose Ethernet type resides in the ctBridgeTransTrEnetSnapTable and is enabled. This selection is overidden by the learned format when ctBridgeTransTrEnetAutoMode is enable and the format has been learned.
OBJECT-TYPE    
  INTEGER ethernet(1), ieee8023snap(2)  

ctBridgeTransTrEnetSnapTable 1.3.6.1.4.1.52.4.1.2.3.7.9
A table containing Ethernet type field entries that the bridge will use to determine how to translate a Token Ring (802.5 w/snap) packet to a CSMA/CD packet. If a received Token Ring packet matches the Ethernet type field of an enabled entry, the bridge will translate the Token Ring packet to the frame format specified by ctBridgeTransTrEnetSnapFormat. Else, it will translate the packet to the opposite frame format.
OBJECT-TYPE    
  SEQUENCE OF  
    CtBridgeTransTrEnetSnapEntry

ctBridgeTransTrEnetSnapEntry 1.3.6.1.4.1.52.4.1.2.3.7.9.1
This entry contains an Ethernet type field value and its associated state.
OBJECT-TYPE    
  CtBridgeTransTrEnetSnapEntry  

ctBridgeTransTrEnetSnapIndex 1.3.6.1.4.1.52.4.1.2.3.7.9.1.1
The index of an entry in the Token Ring to Ethernet Translation table for Ethernet type fields. The index ranges from 1 to 20.
OBJECT-TYPE    
  INTEGER  

ctBridgeTransTrEnetSnapType 1.3.6.1.4.1.52.4.1.2.3.7.9.1.2
The Ethernet type field value which the bridge will translate all Token Ring/802.5 packets with a snap header having this type to the format specified by ctBridgeTransTrEnetSnapFormat. The Ethernet type field value is two octets.
OBJECT-TYPE    
  OCTET STRING  

ctBridgeTransTrEnetSnapState 1.3.6.1.4.1.52.4.1.2.3.7.9.1.3
The state of this entry. A value of 2 indicates that this entry will not be used in the bridge's translation decisions.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctBridgeBaseChassisMgr 1.3.6.1.4.1.52.4.1.2.3.8.1
This object reports the chassis management capability of the bridging device. Chassis management is defined as the ability of the device to report status on MIM boards which the device might be responsible for managing, modifying the state of the MIM boards and the ports residing on the MIM board, and tracking and reporting on the status of the networks being bridged and the stations generating traffic on those networks. Note that this is not a comprehensive list of the activities which comprise chassis management. If chassis management is unsupported by this device, then the value notSupported is returned. If chassis management is supported by this device and the device is, in fact, operating as a chassis manager, then the value managementEnabled is re- turned. If chassis management is supported by this device but the device is not functioning as a chassis manager, the value managementDisabled is returned.
OBJECT-TYPE    
  INTEGER notSupported(1), managementDisabled(2), managementEnabled(3)  

ctBridgeSdbGenericTotFtrs 1.3.6.1.4.1.52.4.1.2.3.9.1
The total number of Generic filters in the special database.
OBJECT-TYPE    
  INTEGER  

ctBridgeSdbGenericNoMatch 1.3.6.1.4.1.52.4.1.2.3.9.2
The process to be performed if no match is found in the Generic special database. The process of filtering or forwarding is for all ports. searchFDB results in searching the IEEE 802.1D transparent filter database referenced by the IETF Bridge MIB.
OBJECT-TYPE    
  INTEGER filter(1), forward(2), searchFDB(3)  

ctBridgeSdbGenericTable 1.3.6.1.4.1.52.4.1.2.3.9.3
A table containing filtering information configured into the bridge by (local or network) management specifying the specific packet string (destination address, source address, type/length field as well as a window of 64 bytes of packet data beginning at a data offset) to be used for filtering decisions. The filters are to be searched in the order of incrementing filter number.
OBJECT-TYPE    
  SEQUENCE OF  
    CtBridgeSdbGenericEntry

ctBridgeSdbGenericEntry 1.3.6.1.4.1.52.4.1.2.3.9.3.1
Filtering information which extends the filtering capability of IEEE 802.1d.
OBJECT-TYPE    
  CtBridgeSdbGenericEntry  

ctBridgeSdbGenericFtrNo 1.3.6.1.4.1.52.4.1.2.3.9.3.1.1
The Filter number for which this entry contains filtering information.
OBJECT-TYPE    
  INTEGER  

ctBridgeSdbGenericState 1.3.6.1.4.1.52.4.1.2.3.9.3.1.2
The state of the filter for which this entry contains filtering information.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctBridgeSdbGenericFtrData 1.3.6.1.4.1.52.4.1.2.3.9.3.1.3
The specific packet string representing the destination address, source address, type/length field and a window of 64 bytes of packet data beginning at DataOffset to be used for filtering decisions. Each ASCII character of the string represents a nibble of packet data, therefore the packet string should be (14+64) * 2 = 156 characters long. A value of 'x' in the packet string is used to indicate a 'Don't care' and no filtering is to be performed on that nibble. The string may be be of size 0 to 78 bytes. If a size less than 78 bytes is used, the string will still begin at the destination address.
OBJECT-TYPE    
  DisplayString Size(0..78)  

ctBridgeSdbGenericDataOffset 1.3.6.1.4.1.52.4.1.2.3.9.3.1.4
The offset into a packet from which the bridge begins its filtering decisions on the 64 byte data window. The value '0' indicates that the window begins at the first byte after the Generic MAC header. The largest value of DataOffset dependent upon the media type.
OBJECT-TYPE    
  INTEGER  

ctBridgeSdbGenericFilterType 1.3.6.1.4.1.52.4.1.2.3.9.3.1.5
This object specifies the type of media for which this special filter entry applies. The value of this object is a bit encoding which allows for multiple medias to share the same filter. The bit numbers are defined as follows, note that bit 0 is considered to be least significant: ethernet - bit 0 Token Ring - bit 1 FDDI - bit 2 There for a filter that was enabled for both FDDI and ethernet would have a value of 5.
OBJECT-TYPE    
  INTEGER  

ctBridgeSdbGenericIOTable 1.3.6.1.4.1.52.4.1.2.3.9.4
A table containing the set of ports to which frames received from specific ports and containing the specific packet string (destination address, source address, type/length field as well as a window of 64 bytes of packet data beginning at a data offset) of the corresponding filter number of SdbGenericTable are allowed to be forwarded. The value of '0' in this table as the RcvPort is used to specify all ports which are not already specified in this table for a particular entry.
OBJECT-TYPE    
  SEQUENCE OF  
    CtBridgeSdbGenericIOEntry

ctBridgeSdbGenericIOEntry 1.3.6.1.4.1.52.4.1.2.3.9.4.1
The set of ports to which frames received by the RcvPort and containing the specific packet string of the corresponding filter number of SdbGenericTable are allowed to be forwarded.
OBJECT-TYPE    
  CtBridgeSdbGenericIOEntry  

ctBridgeSdbGenericIOFtrNo 1.3.6.1.4.1.52.4.1.2.3.9.4.1.1
The Filter number for which this entry contains filtering information.
OBJECT-TYPE    
  INTEGER  

ctBridgeSdbGenericIORcvPort 1.3.6.1.4.1.52.4.1.2.3.9.4.1.2
Either the value '0', or the port number of the port from which a frame must be received in order for this entry's filtering information to apply. A value of '0' indicates that this entry applies on all ports of the bridge for which there is no other applicable entry.
OBJECT-TYPE    
  INTEGER  

ctBridgeSdbGenericIOAllowedToGoTo 1.3.6.1.4.1.52.4.1.2.3.9.4.1.3
The set of ports to which frames received from a specific port and containing the specific packet string of the corresponding filter number are allowed to be forwarded. Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. (Note that the setting of the bit corresponding to the port from which a frame is received is irrelevant.)
OBJECT-TYPE    
  OCTET STRING  

ctBridgeSdbGenericIODelEntry 1.3.6.1.4.1.52.4.1.2.3.9.4.1.4
Writing a '1' to this object deletes this entry from the Generic special database. This object will always return a '1' when read.
OBJECT-TYPE    
  INTEGER deleteEntry(1)  

ctBridgeLoadShareInstanceTable 1.3.6.1.4.1.52.4.1.2.3.10.1
A list of load share instance objects.
OBJECT-TYPE    
  SEQUENCE OF  
    CtBridgeLoadShareInstanceEntry

ctBridgeLoadShareInstanceEntry 1.3.6.1.4.1.52.4.1.2.3.10.1.1
A list of objects for a particular load share instance.
OBJECT-TYPE    
  CtBridgeLoadShareInstanceEntry  

ctBridgeLoadShareInstanceId 1.3.6.1.4.1.52.4.1.2.3.10.1.1.1
Returns the instance for a load share member in the table of load share instances.
OBJECT-TYPE    
  INTEGER  

ctBridgeLoadShareAdminStatus 1.3.6.1.4.1.52.4.1.2.3.10.1.1.2
The administrative state of load sharing for this instance.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctBridgeLoadShareOperStatus 1.3.6.1.4.1.52.4.1.2.3.10.1.1.3
The operational status of load sharing for this instance.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctBridgeLoadSharePortTable 1.3.6.1.4.1.52.4.1.2.3.10.2
A list of load share port objects.
OBJECT-TYPE    
  SEQUENCE OF  
    CtBridgeLoadSharePortEntry

ctBridgeLoadSharePortEntry 1.3.6.1.4.1.52.4.1.2.3.10.2.1
A load share port entry containing objects pertaining to a particular load share port.
OBJECT-TYPE    
  CtBridgeLoadSharePortEntry  

ctBridgeLoadSharePortNum 1.3.6.1.4.1.52.4.1.2.3.10.2.1.1
Returns the port number of a member port belonging to a load share instance.
OBJECT-TYPE    
  INTEGER  

ctBridgeLoadSharePortInstanceId 1.3.6.1.4.1.52.4.1.2.3.10.2.1.2
A unique value indentifying a member instance in the table of load share instances. This value is similar to ctBridgeLoadShareInstanceId.
OBJECT-TYPE    
  INTEGER  

ctBridgeLoadSharePortAdminStatus 1.3.6.1.4.1.52.4.1.2.3.10.2.1.3
The administrative state of the port associated with this instance of load share.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctBridgeLoadSharePortOperStatus 1.3.6.1.4.1.52.4.1.2.3.10.2.1.4
The operational state of the port associated with this instance of load share.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

ctBridgeLoadSharePortForwardMask 1.3.6.1.4.1.52.4.1.2.3.10.2.1.5
The Mask used to foward unknown packets on.
OBJECT-TYPE    
  INTEGER  

ctBridgeLoadSharePortForwardInstance 1.3.6.1.4.1.52.4.1.2.3.10.2.1.6
The instance that the ctLoadSharePortFowardMask is running on for this ctLoadSharePortNumber.
OBJECT-TYPE    
  INTEGER  

ctBridgeLoadSharePortNumPorts 1.3.6.1.4.1.52.4.1.2.3.10.2.1.7
Displays the number of SmartTrunk ports in this redundant path.
OBJECT-TYPE    
  INTEGER