CPE-DSL-MIB

File: CPE-DSL-MIB.mib (25458 bytes)

Imported modules

ATM-MIB IF-MIB SNMPv2-SMI
SNMPv2-TC

Imported symbols

atmVclVpi atmVclVci ifIndex
enterprises IpAddress Integer32
Unsigned32 OBJECT-TYPE MODULE-IDENTITY
NOTIFICATION-TYPE DisplayString RowStatus
DateAndTime TEXTUAL-CONVENTION

Defined Types

EnableAdmin  
Enable operation switch
TEXTUAL-CONVENTION    
  INTEGER enable(1), disable(2)  

PvcIfIndexRange  
ifIndex range of PVC AAL5
TEXTUAL-CONVENTION    
  Integer32 150000..159999  

PppIfIndexRange  
ifIndex range of PPP.
TEXTUAL-CONVENTION    
  Integer32 210000..219999  

EthernetIfIndexRange  
ifIndex range of Ethernet interface.
TEXTUAL-CONVENTION    
  Integer32 10000..19999  

UsbIfIndexRange  
ifIndex range of usb interface.
TEXTUAL-CONVENTION    
  Integer32 20000..29999  

Ieee8022Dot1xIfIndexRange  
ifIndex range of 802.1X interface.
TEXTUAL-CONVENTION    
  Integer32 30000..39999  

AdslIfIndexRange  
ifIndex range of ADSL interface.
TEXTUAL-CONVENTION    
  Integer32 40000..49999  

ModemIfIndexRange  
ifIndex range of Modem interface.
TEXTUAL-CONVENTION    
  Integer32 50000..59999  

Rs232IfIndexRange  
ifIndex range of RS232 interface.
TEXTUAL-CONVENTION    
  Integer32 60000..69999  

BridgeIfIndexRange  
ifIndex range of bridge interface.
TEXTUAL-CONVENTION    
  Integer32 110000..119999  

AdslInterLeaveIfIndexRange  
ifIndex range of ADSL interleave mode interface.
TEXTUAL-CONVENTION    
  Integer32 120000..129999  

AdslFastIfIndexRange  
ifIndex range of ADSL fast mode interface.
TEXTUAL-CONVENTION    
  Integer32 130000..139999  

AdslAtmIfIndexRange  
ifIndex range of ATM interface.
TEXTUAL-CONVENTION    
  Integer32 140000..149999  

CpePvcEntry  
SEQUENCE    
  cpePvcId Integer32
  cpePvcIfIndex PvcIfIndexRange
  cpePvcUpperEncapsulation INTEGER
  cpePvcAdminStatus INTEGER
  cpePvcOperStatus INTEGER
  cpePvcBridgeMode EnableAdmin
  cpePvcMacLearnMode EnableAdmin
  cpePvcIgmpMode EnableAdmin
  cpePvcDhcpClientMode EnableAdmin
  cpePvcNatMode EnableAdmin

CpePppEntry  
SEQUENCE    
  cpePppIfIndex PppIfIndexRange
  cpePppPvcIfIndex PvcIfIndexRange
  cpePppServiceName DisplayString
  cpePppDisconnectTimeout INTEGER
  cpePppMSS INTEGER
  cpePppRowStatus RowStatus
  cpePppAdminStatus INTEGER
  cpePppOperStatus INTEGER
  cpePppTestResult INTEGER

CpeIpEntry  
SEQUENCE    
  cpeIpIndex Unsigned32
  cpeIpLowerIfIndex Integer32
  cpeIpAddress IpAddress
  cpeIpNetmask IpAddress
  cpeIpGateway IpAddress
  cpeIpRowStatus RowStatus

CpeSysLogEntry  
SEQUENCE    
  cpeSysLogIndex Unsigned32
  cpeSysLogContent DisplayString

Defined Values

cpeDSL 1.1.16972
xDSL CPE MIB.
MODULE-IDENTITY    

cpeSysInfo 1.1.16972.1
OBJECT IDENTIFIER    

cpeSysInfoUptime 1.1.16972.1.1
It is the working time since CPE rebooted.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cpeSysInfoConfigId 1.1.16972.1.2
for synchronizing configuration by network manager
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..4)  

cpeSysInfoFirmwareVersion 1.1.16972.1.3
Chipset version information.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

cpeSysInfoProductId 1.1.16972.1.4
CPE product module,For example, the 'MT800' is the product id.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

cpeSysInfoVendorId 1.1.16972.1.5
the name of CPE vendor.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

cpeSysInfoSystemVersion 1.1.16972.1.6
CPE system version
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

cpeSysInfoWorkMode 1.1.16972.1.7
CPE s work mode.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER bridge(1), router(2)  

cpeSysInfoMibVersion 1.1.16972.1.8
The MIB's version,now the vaersion is V1.00
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..8)  

cpeSysInfoSerialNumber 1.1.16972.1.9
The CPE's BAR CODE including serial number to identify itself to each other it is embedded by equipment provider while manufacturing .
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

cpeSysInfoManufacturerOui 1.1.16972.1.10
the OUI (Organizationally Unique Identifier) of IEEE standard organization provided. For example, this huawei CPE ADSL is 00E0FC
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..6)  

cpeConfig 1.1.16972.2
OBJECT IDENTIFIER    

cpeSystem 1.1.16972.2.1
OBJECT IDENTIFIER    

cpeSystemReboot 1.1.16972.2.1.1
Rebooting CPE s operation
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reboot(1)  

cpeSystemSave 1.1.16972.2.1.2
saving the CPE s configuration to NVRAM
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER save(1)  

cpeSystemRestore 1.1.16972.2.1.3
Restore CPE s configuration restoreToNull(1), clear all of the configuration restoreToDefault(2) restore to default configuration
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER restoreToNull(1), restoreToDefault(2)  

cpeSystemTrapEnable 1.1.16972.2.1.4
trap notification switch, if set to Disable CPE will not send trap notification untill it is set to enable
Status: current Access: read-write
OBJECT-TYPE    
  EnableAdmin  

cpeBootTrapResponse 1.1.16972.2.1.5
It is the boottrap response identity Every time,when CPE is rebooted, it is set to 'noResponse'
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noResponse(1), responseCfgReady(2), responseReCfg(3)  

cpeReservedString 1.1.16972.2.1.6
It is the reserved string
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..255)  

cpeConfigAdslLine 1.1.16972.2.2
OBJECT IDENTIFIER    

cpeConfigAdslLineTrellis 1.1.16972.2.2.1
trellis encoding configuration.
Status: current Access: read-write
OBJECT-TYPE    
  EnableAdmin  

cpeConfigAdslLineHandshake 1.1.16972.2.2.2
link handshake negotiation mode configuration
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER autosenseGdmtFirst(1), autosenseT1413First(2), gdmtOrLite(3), t1413(4), gdmt(5), glite(6), autosense(7)  

cpeConfigAdslLineBitSwapping 1.1.16972.2.2.3
BITSWAP encoding configuration
Status: current Access: read-write
OBJECT-TYPE    
  EnableAdmin  

cpePvcTable 1.1.16972.2.3
PVC VCL configuration table It is RFC2515 ATM-MIB atmVclTable s extended table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CpePvcEntry

cpePvcEntry 1.1.16972.2.3.1
PVC VCL configuration entry
Status: current Access: not-accessible
OBJECT-TYPE    
  CpePvcEntry  

cpePvcId 1.1.16972.2.3.1.1
PVC number It is used for identify PVC in CPE
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cpePvcIfIndex 1.1.16972.2.3.1.3
this parameter is used for bonding upper layer service s index
Status: current Access: read-only
OBJECT-TYPE    
  PvcIfIndexRange  

cpePvcUpperEncapsulation 1.1.16972.2.3.1.4
PVC service encapsulation type
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER pppoA(1), pppoE(2), router2684(3), pureBridge2684(4), bridge2684PlusIp(5), ilmi(7)  

cpePvcAdminStatus 1.1.16972.2.3.1.5
PVC active and deactive operation, We suggest to use the atmVclAdminStatus in the vclTableof ATM-MIB instead ofcpePvcAdminStatus
Status: deprecated Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2)  

cpePvcOperStatus 1.1.16972.2.3.1.6
PVC active and deactive status. We suggest to use the atmVclOperStatus in the vclTableof ATM-MIB instead of cpePvcOperStatus
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

cpePvcBridgeMode 1.1.16972.2.3.1.7
bridge mode configuration only when cpePvcUpperEncapsulation is set to 'bridge2684' this configuration is available
Status: current Access: read-create
OBJECT-TYPE    
  EnableAdmin  

cpePvcMacLearnMode 1.1.16972.2.3.1.8
MAC address learn mode configuration, it's no use.
Status: deprecated Access: read-create
OBJECT-TYPE    
  EnableAdmin  

cpePvcIgmpMode 1.1.16972.2.3.1.9
if IGMP traffic and internet traffic service is beared by different PVC It can be configured by this parameter
Status: current Access: read-create
OBJECT-TYPE    
  EnableAdmin  

cpePvcDhcpClientMode 1.1.16972.2.3.1.10
DHCP client mode configuration
Status: current Access: read-create
OBJECT-TYPE    
  EnableAdmin  

cpePvcNatMode 1.1.16972.2.3.1.11
NAT mode configuration
Status: current Access: read-create
OBJECT-TYPE    
  EnableAdmin  

cpePppTable 1.1.16972.2.4
PPP configuration table,it is pppSecuritySecretsTable s extended table pppSecuritySecretsLink is set to 0 cpePppIfIndex pppSecuritySecretsIdIndex
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CpePppEntry

cpePppEntry 1.1.16972.2.4.1
PPP configuration entry
Status: current Access: not-accessible
OBJECT-TYPE    
  CpePppEntry  

cpePppIfIndex 1.1.16972.2.4.1.1
ppp s index
Status: current Access: read-only
OBJECT-TYPE    
  PppIfIndexRange  

cpePppPvcIfIndex 1.1.16972.2.4.1.2
the lower layer logic interface index for ppp,also the ATM layer logic interface index for ppp,the value is the same as cpePvcIfindex
Status: current Access: read-create
OBJECT-TYPE    
  PvcIfIndexRange  

cpePppServiceName 1.1.16972.2.4.1.3
PPP service name
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

cpePppDisconnectTimeout 1.1.16972.2.4.1.4
PPP idle disconnect timeout parameter, if it is set to zero, the PPP connection will not Be disconnected. If it not set to zero, the PPP will be disconnected if there is no traffic on the PPP for the specified period.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..32767  

cpePppMSS 1.1.16972.2.4.1.5
PPP s max segment size
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..32767  

cpePppRowStatus 1.1.16972.2.4.1.6
PPP table s row status
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cpePppAdminStatus 1.1.16972.2.4.1.7
Ppp link operation up(1), activate operation down(2), deactivate operation test(3), PPP test,test operating should generated an trap after it is done. cannel(4),stop the PPP testing
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER up(1), down(2), test(3), cancel(4)  

cpePppOperStatus 1.1.16972.2.4.1.8
ppp link status up(1): active status down(2):deactive status
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

cpePppTestResult 1.1.16972.2.4.1.9
ppp test result success(1), testing(2) authFail(3), failure(4)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER success(1), testing(2), authFail(3), failure(4)  

cpeIpTable 1.1.16972.2.5
IP address table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CpeIpEntry

cpeIpEntry 1.1.16972.2.5.1
Interface s IP address entry
Status: current Access: not-accessible
OBJECT-TYPE    
  CpeIpEntry  

cpeIpIndex 1.1.16972.2.5.1.1
IP address table s index
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cpeIpLowerIfIndex 1.1.16972.2.5.1.2
lower layer s logic index
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

cpeIpAddress 1.1.16972.2.5.1.3
IP address
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

cpeIpNetmask 1.1.16972.2.5.1.4
IP address netmask
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

cpeIpGateway 1.1.16972.2.5.1.5
the gateway address, NMS could config it only when the IP is gained by static mode, otherwise ,it can be read-ony mode.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

cpeIpRowStatus 1.1.16972.2.5.1.6
the row status of IP address table
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cpeLanDhcp 1.1.16972.2.6
OBJECT IDENTIFIER    

cpeLanDhcpAdminStatus 1.1.16972.2.6.1
dhcp mode configuration noSupport(1), no support dhcp dhcpServer(2),support dhcp server
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noSupport(1), dhcpServer(2)  

cpeWanDns 1.1.16972.2.7
OBJECT IDENTIFIER    

cpeDnsPrimaryAddress 1.1.16972.2.7.1
the primary DNS IP address
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

cpeDnsSecondAddress 1.1.16972.2.7.2
the secondary DNS IP address
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

cpeSysLog 1.1.16972.3
OBJECT IDENTIFIER    

cpeSysLogBeginTime 1.1.16972.3.1
syslog requery s begin time
Status: current Access: read-write
OBJECT-TYPE    
  DateAndTime  

cpeSysLogEndTime 1.1.16972.3.2
syslog requery s end time
Status: current Access: read-write
OBJECT-TYPE    
  DateAndTime  

cpeSysLogAdminStatus 1.1.16972.3.3
requery syslog operation start(1), start requery syslog clear(2), clear CPE s syslog record
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER start(1), clear(2)  

cpeSysLogTable 1.1.16972.3.4
syslog record s table
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CpeSysLogEntry

cpeSysLogEntry 1.1.16972.3.4.1
syslog record s entry
Status: current Access: not-accessible
OBJECT-TYPE    
  CpeSysLogEntry  

cpeSysLogIndex 1.1.16972.3.4.1.1
the syslog record s index
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

cpeSysLogContent 1.1.16972.3.4.1.2
the syslog s detail description
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

cpeFtp 1.1.16972.4
OBJECT IDENTIFIER    

cpeFtpIP 1.1.16972.4.1
the FTP Server s IP address
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

cpeFtpUser 1.1.16972.4.2
the user name for FTP
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..127)  

cpeFtpPasswd 1.1.16972.4.3
the access password for FTP
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..127)  

cpeFtpFileName 1.1.16972.4.4
the file name for ftp download which is saved in FTP server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(4..255)  

cpeFtpAdminStatus 1.1.16972.4.5
FTP administration operation
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER stop(1), upgrade(2), ftpTest(3)  

cpeFtpOperStatus 1.1.16972.4.6
FTP administration status
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), connectSuccess(2), connectFailure(3), downloading(4), downloadSuccess(5), downloadFailure(6), saving(7), saveFailure(8), upgradeSuccess(9), upgradeFailure(10)  

cpeFtpTotalSize 1.1.16972.4.8
the file s total size for download unit is Kbyte
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cpeFtpDoneSize 1.1.16972.4.9
the file s size which is already download unit is Kbyte
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cpeFtpElapseTime 1.1.16972.4.10
the elapse time for FTP download
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

cpeDiagnose 1.1.16972.5
OBJECT IDENTIFIER    

cpePing 1.1.16972.5.1
OBJECT IDENTIFIER    

cpePingAddr 1.1.16972.5.1.1
the destination IP address for ping test either IP or Domain name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(4..255)  

cpePingPkgSize 1.1.16972.5.1.2
the packet size for ping test
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 32..4096  

cpePingCount 1.1.16972.5.1.3
the count of sending packets for ping test
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..32767  

cpePingAdminStatus 1.1.16972.5.1.4
ping test operation stop(1), start ping test start(2) stop ping test
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER stop(1), start(2)  

cpePingOperStatus 1.1.16972.5.1.5
ping test operation status
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), pinging(2), success(3), failure(4)  

cpePingResult 1.1.16972.5.1.6
ping test result IP 10.1.1.100 Sent = xx Received = xx Lost = xx Min = xx ms Max = xx ms Average = xx ms
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

cpeTrap 1.1.16972.6
OBJECT IDENTIFIER    

cpeTraps 1.1.16972.6.0
OBJECT IDENTIFIER    

cpeBootTrap 1.1.16972.6.0.1
trap notification when CPE is rebooted. CPE is needed to send all parameters in one trap packet.
Status: current Access: read-only
NOTIFICATION-TYPE    

cpeFtpDone 1.1.16972.6.0.2
trap notification when ftp download is finished
Status: current Access: read-only
NOTIFICATION-TYPE    

cpePingDone 1.1.16972.6.0.3
trap notification when PING test is finished
Status: current Access: read-only
NOTIFICATION-TYPE    

cpePppTestDone 1.1.16972.6.0.4
trap notification when PPP test is finished
Status: current Access: read-only
NOTIFICATION-TYPE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor