CISCO-WAN-CODEC-GEN-PARM-MIB

File: CISCO-WAN-CODEC-GEN-PARM-MIB.mib (12885 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF CISCOWAN-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE MODULE-COMPLIANCE
OBJECT-GROUP ciscoWan

Defined Types

VismCodecGenParmEntry  
SEQUENCE    
  vismCodecIndex INTEGER
  vismCodecJitterDelayMode INTEGER
  vismCodecJitterInitialDelay INTEGER

Defined Values

ciscoWanCodecGenParmMIB 1.3.6.1.4.1.351.150.21
This MIB provides configuration of Jitter buffer mode on a call and initial jitter delay value per Codec based. Prior to this, the configuration are specify on a Card based. The Card level objects vismJitterDelayMode and vismJitterInitialDelay in CISCO-VISM-MODULE-MIB are now deprecated.
MODULE-IDENTITY    

ciscoWanCodecGenParmMIBObjects 1.3.6.1.4.1.351.150.21.1
OBJECT IDENTIFIER    

vismCodecGenParmGrp 1.3.6.1.4.1.351.150.21.1.1
OBJECT IDENTIFIER    

vismCodecGenParmTable 1.3.6.1.4.1.351.150.21.1.1.1
vismCodecGenParmTable contains configuration information about per codec based general parameters regardless of its application.
OBJECT-TYPE    
  SEQUENCE OF  
    VismCodecGenParmEntry

vismCodecGenParmEntry 1.3.6.1.4.1.351.150.21.1.1.1.1
User can modify the parameters at any time. If there are active calls going on, the new settings will not take affect until the next call. The last modified values are retained when VISM card reboots.
OBJECT-TYPE    
  VismCodecGenParmEntry  

vismCodecIndex 1.3.6.1.4.1.351.150.21.1.1.1.1.1
This is the index to this table. 1 represents G.711u 2 represents G.711a 3 represents G.726 at rate 32 kbps 4 represents G.729a 5 represents G.729ab 6 represents clear channel 7 represents G.726 at rate 16 kbps 8 represents G.726 at rate 24 kbps 9 represents G.726 at rate 40 kbps 10 is RESERVED 11 represents G.723.1-H 12 represents G.723.1a-H 13 represents G.723.1-L 14 represents G.723.1a-L 15 represents Lossless
OBJECT-TYPE    
  INTEGER g711u(1), g711a(2), g726r32000(3), g729a(4), g729ab(5), clearChannel(6), g726r16000(7), g726r24000(8), g726r40000(9), g723h(11), g723ah(12), g723l(13), g723al(14), lossless(15)  

vismCodecJitterDelayMode 1.3.6.1.4.1.351.150.21.1.1.1.1.2
This object is used to provision the jitter buffer mode to be apply to a call connection. The possible values are: 'fixed' : means use a constant jitter buffer size, which is defined by the vismJitterInitialDelay (specify in CISCO-VISM-MODULE-MIB MIB) variable. The DSP will be instructed to use fixed with no time-stamps mode. 'adaptive': means let the DSP pick the optimal value for the call connection. 'fixedWithTimeStamp': means use a constant jitter buffer size, which is defined by the vismJitterInitialDelay variable. The DSP will be instructed to use fixed with time-stamps mode. For 'g711u', 'g711a', 'clearChannel', and 'lossless' the default value is fixed. For 'g726r32000', 'g729a', 'g729ab', 'g726r16000', 'g726r24000','g726r40000', 'g723h','g723l', 'g723ah' and 'g723al' the default value is adaptive.
OBJECT-TYPE    
  INTEGER fixed(1), adaptive(2), fixedWithTimeStamp(3)  

vismCodecJitterInitialDelay 1.3.6.1.4.1.351.150.21.1.1.1.1.3
This object defines the jitter buffer size in milliseconds. If the vismCodecJitterDelayMode is set to be 'fixed', the jitter buffer is fixed at this value for the duration of the call, if it is set to 'adaptive', the value of this object is the initial jitter buffer size, and the DSP will adapt to an optimal size dynamically. For G.711u, G.711a, Clear Channel, the default value is 100 ms. For lossless the default value is 16ms. For 'g726r32000', 'g729a', 'g729ab', 'g726r16000', 'g726r24000','g726r40000', 'g723h','g723l', 'g723ah' and 'g723al' the default value is 60 ms. The jitter buffer size of this object differs for each set of codecs supported on VISM card. A set of codecs supported is identified by vismCodecTemplateNum object(defined in CISCO-VISM-CODEC-MIB MIB). For codecs in template number 1, 3, 4, and 5: the jitter buffer size is as follow: 'zero', 'five', 'ten' 'fifteen', 'twenty', 'thirty', 'fourty', 'fifty', 'sixty', 'seventy', 'eighty', 'ninty', 'hundred'. For codecs in template 2, the jitter buffer size is as follow: 'zero', 'five', 'ten', 'fifteen', 'twenty', 'twentyfive', 'thirty', 'thirtyfive', 'fourty', 'fortyfive', 'fifty', 'fiftyfive', 'sixty', 'sixtyfive', 'seventy', 'seventyfive', 'eighty', 'eightyfive', 'ninty', 'ninetyfive', 'hundred'. When the codec template changes, the value of this object will be implicitly set to the default value.
OBJECT-TYPE    
  INTEGER zero(1), two(2), three(3), four(4), five(5), six(6), seven(7), eight(8), nine(9), ten(10), eleven(11), twelve(12), thirteen(13), fourteen(14), fifteen(15), sixteen(16), seventeen(17), eighteen(18), nineteen(19), twenty(20), twentyone(21), twentytwo(22), twentythree(23), twentyfour(24), twentyfive(25), twentysix(26), twentyseven(27), twentyeight(28), twentynine(29), thirty(30), thirtyone(31), thirtytwo(32), thirtythree(33), thirtyfour(34), thirtyfive(35), thirtysix(36), thirtyseven(37), thirtyeight(38), thirtynine(39), fourty(40), fortyone(41), fortytwo(42), fortythree(43), fortyfour(44), fortyfive(45), fortysix(46), fortyseven(47), fortyeight(48), fortynine(49), fifty(50), fiftyfive(55), sixty(60), sixtyfive(65), seventy(70), seventyfive(75), eighty(80), eightyfive(85), ninty(90), ninetyfive(95), hundred(100)  

vismCodecGenParmNotificationPrefix 1.3.6.1.4.1.351.150.21.2
OBJECT IDENTIFIER    

vismCodecGenParmNotifications 1.3.6.1.4.1.351.150.21.2.0
OBJECT IDENTIFIER    

vismCodecGenParmMIBConformance 1.3.6.1.4.1.351.150.21.3
OBJECT IDENTIFIER    

vismCodecGenParmMIBCompliances 1.3.6.1.4.1.351.150.21.3.1
OBJECT IDENTIFIER    

vismCodecGenParmMIBGroups 1.3.6.1.4.1.351.150.21.3.2
OBJECT IDENTIFIER    

vismCodecGenParmMIBCompliance 1.3.6.1.4.1.351.150.21.3.1.1
The complaince statement for VISM codec general parameter group.
MODULE-COMPLIANCE    

vismCodecGenParmGroup 1.3.6.1.4.1.351.150.21.3.2.1
This group contains objects that is per codec based and non application specific.
OBJECT-GROUP