CIE1000-POE-MIB

File: CIE1000-POE-MIB.mib (15932 bytes)

Imported modules

SNMPv2-CONF SNMPv2-SMI SNMPv2-TC
CISCO-IE1000-MIB CIE1000-TC

Imported symbols

NOTIFICATION-GROUP MODULE-COMPLIANCE OBJECT-GROUP
NOTIFICATION-TYPE MODULE-IDENTITY OBJECT-TYPE
TEXTUAL-CONVENTION cie1000SwitchMgmt CIE1000InterfaceIndex
Integer32 Unsigned32 TruthValue

Defined Types

CIE1000poeMgmtModeType  
TEXTUAL-CONVENTION    
  current INTEGER classReservedPower(0), classConsumption(1), allocatedReservedPower(2), allocatedConsumption(3), lldpReservedPower(4), lldpConsumption(5)

CIE1000poeModeType  
TEXTUAL-CONVENTION    
  current INTEGER disable(0), poeDot3af(1), poePlusDot3at(2)

CIE1000poePowerPriorityType  
TEXTUAL-CONVENTION    
  current INTEGER low(0), high(1), critical(2)

CIE1000poeStatusType  
TEXTUAL-CONVENTION    
  current INTEGER notSupported(0), budgetExceeded(1), noPoweredDeviceDetected(2), poweredDeviceOn(3), poweredDeviceOff(4), poweredDeviceOverloaded(5), unknownState(6), disabled(7)

CIE1000PoeCapabilitiesInterfaceEntry  
SEQUENCE    
  cie1000PoeCapabilitiesInterfaceIfIndex CIE1000InterfaceIndex
  cie1000PoeCapabilitiesInterfacePoE TruthValue

CIE1000PoeConfigSwitchParamEntry  
SEQUENCE    
  cie1000PoeConfigSwitchParamSwitchId Unsigned32
  cie1000PoeConfigSwitchParamMaxPower Integer32
  cie1000PoeConfigSwitchParamCapacitorDetection TruthValue

CIE1000PoeConfigInterfaceParamEntry  
SEQUENCE    
  cie1000PoeConfigInterfaceParamIfIndex CIE1000InterfaceIndex
  cie1000PoeConfigInterfaceParamMode CIE1000poeModeType
  cie1000PoeConfigInterfaceParamPriority CIE1000poePowerPriorityType
  cie1000PoeConfigInterfaceParamMaxPower Integer32

CIE1000PoeStatusInterfaceEntry  
SEQUENCE    
  cie1000PoeStatusInterfaceIfIndex CIE1000InterfaceIndex
  cie1000PoeStatusInterfacePDClass Integer32
  cie1000PoeStatusInterfaceCurrentState CIE1000poeStatusType
  cie1000PoeStatusInterfacePowerConsumption Integer32
  cie1000PoeStatusInterfacePowerReserved Integer32
  cie1000PoeStatusInterfaceCurrentConsumption Integer32

Defined Values

cie1000PoeMib 1.3.6.1.4.1.9.9.832.1.43
This is a private version of Power over Ethernet(PoE).
MODULE-IDENTITY    

cie1000PoeMibObjects 1.3.6.1.4.1.9.9.832.1.43.1
OBJECT IDENTIFIER    

cie1000PoeCapabilities 1.3.6.1.4.1.9.9.832.1.43.1.1
OBJECT IDENTIFIER    

cie1000PoeCapabilitiesInterfaceTable 1.3.6.1.4.1.9.9.832.1.43.1.1.1
This is a table to interface capabilities
OBJECT-TYPE    
  SEQUENCE OF  
    CIE1000PoeCapabilitiesInterfaceEntry

cie1000PoeCapabilitiesInterfaceEntry 1.3.6.1.4.1.9.9.832.1.43.1.1.1.1
Each interface has a set of capability parameters
OBJECT-TYPE    
  CIE1000PoeCapabilitiesInterfaceEntry  

cie1000PoeCapabilitiesInterfaceIfIndex 1.3.6.1.4.1.9.9.832.1.43.1.1.1.1.1
Logical interface number.
OBJECT-TYPE    
  CIE1000InterfaceIndex  

cie1000PoeCapabilitiesInterfacePoE 1.3.6.1.4.1.9.9.832.1.43.1.1.1.1.2
Indicates whether interface is PoE capable or not.
OBJECT-TYPE    
  TruthValue  

cie1000PoeConfig 1.3.6.1.4.1.9.9.832.1.43.1.2
OBJECT IDENTIFIER    

cie1000PoeConfigGlobals 1.3.6.1.4.1.9.9.832.1.43.1.2.1
OBJECT IDENTIFIER    

cie1000PoeConfigGlobalsManagementMode 1.3.6.1.4.1.9.9.832.1.43.1.2.1.1
PoE management modes, six PoE management modes are supported. CLASS_RESERVED: Maximum port power determined by class, and power is managed according to power consumption. CLASS_CONSUMP: Maximum port power determined by class, and power is managed according to reserved power. ALLOCATED_RESERVED: Maximum port power determined by allocation, and power is managed according to power consumption. ALLOCATED_CONSUMP: Maximum port power determined by allocation, and power is managed according to reserved power. LLDPMED_RESERVED: Maximum port power determined by LLDP Media protocol, and power is managed according to reserved power. LLDPMED_CONSUMP: Maximum port power determined by LLDP Media protocol, and power is managed according to power consumption.
OBJECT-TYPE    
  CIE1000poeMgmtModeType  

cie1000PoeConfigSwitch 1.3.6.1.4.1.9.9.832.1.43.1.2.2
OBJECT IDENTIFIER    

cie1000PoeConfigSwitchParamTable 1.3.6.1.4.1.9.9.832.1.43.1.2.2.1
This is a table to configure PoE configurations for a switch.
OBJECT-TYPE    
  SEQUENCE OF  
    CIE1000PoeConfigSwitchParamEntry

cie1000PoeConfigSwitchParamEntry 1.3.6.1.4.1.9.9.832.1.43.1.2.2.1.1
Each switch has a set of PoE configurable parameters
OBJECT-TYPE    
  CIE1000PoeConfigSwitchParamEntry  

cie1000PoeConfigSwitchParamSwitchId 1.3.6.1.4.1.9.9.832.1.43.1.2.2.1.1.1
User Switch Id.
OBJECT-TYPE    
  Unsigned32 1..16  

cie1000PoeConfigSwitchParamMaxPower 1.3.6.1.4.1.9.9.832.1.43.1.2.2.1.1.2
The Maximum power(in Watt) that the power sourcing equipment(such as switch) can deliver.
OBJECT-TYPE    
  Integer32 0..180  

cie1000PoeConfigSwitchParamCapacitorDetection 1.3.6.1.4.1.9.9.832.1.43.1.2.2.1.1.3
Indicates whether switch capacitor detection feature is enabled or not.
OBJECT-TYPE    
  TruthValue  

cie1000PoeConfigInterface 1.3.6.1.4.1.9.9.832.1.43.1.2.3
OBJECT IDENTIFIER    

cie1000PoeConfigInterfaceParamTable 1.3.6.1.4.1.9.9.832.1.43.1.2.3.1
This is a table to configure PoE configurations for a specific interface.
OBJECT-TYPE    
  SEQUENCE OF  
    CIE1000PoeConfigInterfaceParamEntry

cie1000PoeConfigInterfaceParamEntry 1.3.6.1.4.1.9.9.832.1.43.1.2.3.1.1
Each interface has a set of PoE configurable parameters
OBJECT-TYPE    
  CIE1000PoeConfigInterfaceParamEntry  

cie1000PoeConfigInterfaceParamIfIndex 1.3.6.1.4.1.9.9.832.1.43.1.2.3.1.1.1
Logical interface number.
OBJECT-TYPE    
  CIE1000InterfaceIndex  

cie1000PoeConfigInterfaceParamMode 1.3.6.1.4.1.9.9.832.1.43.1.2.3.1.1.2
Set PoE mode or disable PoE feature, two PoE modes are supported. POE: Enables PoE based on IEEE 802.3af standard, and provides power up to 15.4W(154 deciwatt) of DC power to powered device. When changing to standard mode the MaxPower is automatically adjust to 15.4 W, if it currently exceeds 15.4 W. POE_PLUS: Enabled PoE based on IEEE 802.3at standard, and provides power up to 30W(300 deciwatt) of DC power to powered device.
OBJECT-TYPE    
  CIE1000poeModeType  

cie1000PoeConfigInterfaceParamPriority 1.3.6.1.4.1.9.9.832.1.43.1.2.3.1.1.3
Set port power priority. Priority determines the order in which the interfaces will receive power. Interfaces with a higher priority will receive power before interfaces with a lower priority. PRIORITY_LOW means lowest priority. PRIORITY_HIGH means medium priority. PRIORITY_CRITICAL means highest priority.
OBJECT-TYPE    
  CIE1000poePowerPriorityType  

cie1000PoeConfigInterfaceParamMaxPower 1.3.6.1.4.1.9.9.832.1.43.1.2.3.1.1.4
Maximum port power(in deciwatt) that can be delivered to remote device. Maximum allowed values from 0 to 154 deciwatt in POE standard mode, and from 0 to 300 deciwatt in POE plus mode.
OBJECT-TYPE    
  Integer32 0..300  

cie1000PoeStatus 1.3.6.1.4.1.9.9.832.1.43.1.3
OBJECT IDENTIFIER    

cie1000PoeStatusInterfaceTable 1.3.6.1.4.1.9.9.832.1.43.1.3.1
This is a table to Power over Ethernet interface status
OBJECT-TYPE    
  SEQUENCE OF  
    CIE1000PoeStatusInterfaceEntry

cie1000PoeStatusInterfaceEntry 1.3.6.1.4.1.9.9.832.1.43.1.3.1.1
Each interface has a set of status parameters
OBJECT-TYPE    
  CIE1000PoeStatusInterfaceEntry  

cie1000PoeStatusInterfaceIfIndex 1.3.6.1.4.1.9.9.832.1.43.1.3.1.1.1
Logical interface number.
OBJECT-TYPE    
  CIE1000InterfaceIndex  

cie1000PoeStatusInterfacePDClass 1.3.6.1.4.1.9.9.832.1.43.1.3.1.1.2
Powered device(PD) negotiates a power class with sourcing equipment(PSE) during the time of initial connection, each class have a maximum supported power. Class assigned to PD is based on PD electrical characteristics. Value -1 means either PD attached to the interface can not advertise its power class or no PD detected or PoE is not supported or PoE feature is disabled or unsupported PD class(classes 0-4 is supported).
OBJECT-TYPE    
  Integer32  

cie1000PoeStatusInterfaceCurrentState 1.3.6.1.4.1.9.9.832.1.43.1.3.1.1.3
Indicate port status. POWER_BUDGET_EXCEEDED: PoE is turned OFF due to power budget exceeded on PSE. NO_PD_DETECTED: No PD detected. PD_ON: PSE supplying power to PD through PoE. PD_OVERLOAD: PD consumes more power than the maximum limit configured on the PSE port.
OBJECT-TYPE    
  CIE1000poeStatusType  

cie1000PoeStatusInterfacePowerConsumption 1.3.6.1.4.1.9.9.832.1.43.1.3.1.1.4
Indicates the power(in deciwatt) that the PD is consuming right now.
OBJECT-TYPE    
  Integer32  

cie1000PoeStatusInterfacePowerReserved 1.3.6.1.4.1.9.9.832.1.43.1.3.1.1.5
Indicates the power(in deciwatt) that the PD has requested/reserved.
OBJECT-TYPE    
  Integer32  

cie1000PoeStatusInterfaceCurrentConsumption 1.3.6.1.4.1.9.9.832.1.43.1.3.1.1.6
Indicates the current(in mA) that the PD is consuming right now.
OBJECT-TYPE    
  Integer32  

cie1000PoeMibConformance 1.3.6.1.4.1.9.9.832.1.43.2
OBJECT IDENTIFIER    

cie1000PoeMibCompliances 1.3.6.1.4.1.9.9.832.1.43.2.1
OBJECT IDENTIFIER    

cie1000PoeMibGroups 1.3.6.1.4.1.9.9.832.1.43.2.2
OBJECT IDENTIFIER    

cie1000PoeCapabilitiesInterfaceInfoGroup 1.3.6.1.4.1.9.9.832.1.43.2.2.1
A collection of objects.
OBJECT-GROUP    

cie1000PoeConfigGlobalsInfoGroup 1.3.6.1.4.1.9.9.832.1.43.2.2.2
A collection of objects.
OBJECT-GROUP    

cie1000PoeConfigSwitchParamTableInfoGroup 1.3.6.1.4.1.9.9.832.1.43.2.2.3
A collection of objects.
OBJECT-GROUP    

cie1000PoeConfigInterfaceParamTableInfoGroup 1.3.6.1.4.1.9.9.832.1.43.2.2.4
A collection of objects.
OBJECT-GROUP    

cie1000PoeStatusInterfaceTableInfoGroup 1.3.6.1.4.1.9.9.832.1.43.2.2.5
A collection of objects.
OBJECT-GROUP    

cie1000PoeMibCompliance 1.3.6.1.4.1.9.9.832.1.43.2.1.1
The compliance statement for the implementation.
MODULE-COMPLIANCE