CCPOWER-MIB

File: CCPOWER-MIB.mib (52584 bytes)

Imported modules

RFC1155-SMI RFC1213-MIB RFC-1212
RFC-1215

Imported symbols

enterprises DisplayString OBJECT-TYPE
TRAP-TYPE

Defined Values

ccpower 1.3.6.1.4.1.18642
OBJECT IDENTIFIER    

dcSystem 1.3.6.1.4.1.18642.1
OBJECT IDENTIFIER    

readWriteObjects 1.3.6.1.4.1.18642.1.1
OBJECT IDENTIFIER    

settings 1.3.6.1.4.1.18642.1.1.1
OBJECT IDENTIFIER    

floatVoltage 1.3.6.1.4.1.18642.1.1.1.1
Rectifier DC Output Voltage. Return value is XXX representing XX.X volts.
OBJECT-TYPE    
  INTEGER  

overloadCurrent 1.3.6.1.4.1.18642.1.1.1.2
Current which when exceeded will cause an alarm. Return value is XXXX representing XXXX amps.
OBJECT-TYPE    
  INTEGER  

highVoltageAlarm 1.3.6.1.4.1.18642.1.1.1.3
Voltage which when exceeded will cause an alarm. Return value is XXX representing XX.X volts.
OBJECT-TYPE    
  INTEGER  

lowVoltageAlarm 1.3.6.1.4.1.18642.1.1.1.4
Voltage which when exceeded will cause an alarm. Return value is XXX representing XX.X volts.
OBJECT-TYPE    
  INTEGER  

disconnect1Voltage 1.3.6.1.4.1.18642.1.1.1.5
Voltage which when exceeded will cause a specific load to disconnect. Return value is XXX representing XX.X volts.
OBJECT-TYPE    
  INTEGER  

disconnect1Temperature 1.3.6.1.4.1.18642.1.1.1.6
Temperature which when exceeded will cause a specific load to disconnect. Return value is XX representing XX C.
OBJECT-TYPE    
  INTEGER  

disconnect1LoadShedSundayOff 1.3.6.1.4.1.18642.1.1.1.7
Time on Sunday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect1LoadShedMondayOff 1.3.6.1.4.1.18642.1.1.1.8
Time on Monday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect1LoadShedTuesdayOff 1.3.6.1.4.1.18642.1.1.1.9
Time on Tuesday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect1LoadShedWednesdayOff 1.3.6.1.4.1.18642.1.1.1.10
Time on Wednesday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect1LoadShedThursdayOff 1.3.6.1.4.1.18642.1.1.1.11
Time on Thursday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect1LoadShedFridayOff 1.3.6.1.4.1.18642.1.1.1.12
Time on Friday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect1LoadShedSaturdayOff 1.3.6.1.4.1.18642.1.1.1.13
Time on Saturday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect2Voltage 1.3.6.1.4.1.18642.1.1.1.14
Voltage which when exceeded will cause a specific load to disconnect. Return value is XXX representing XX.X volts.
OBJECT-TYPE    
  INTEGER  

disconnect2Temperature 1.3.6.1.4.1.18642.1.1.1.15
Temperature which when exceeded will cause a specific load to disconnect. Return value is XX representing XX C.
OBJECT-TYPE    
  INTEGER  

disconnect2LoadShedSundayOff 1.3.6.1.4.1.18642.1.1.1.16
Time on Sunday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect2LoadShedMondayOff 1.3.6.1.4.1.18642.1.1.1.17
Time on Monday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect2LoadShedTuesdayOff 1.3.6.1.4.1.18642.1.1.1.18
Time on Tuesday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect2LoadShedWednesdayOff 1.3.6.1.4.1.18642.1.1.1.19
Time on Wednesday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect2LoadShedThursdayOff 1.3.6.1.4.1.18642.1.1.1.20
Time on Thursday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect2LoadShedFridayOff 1.3.6.1.4.1.18642.1.1.1.21
Time on Friday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect2LoadShedSaturdayOff 1.3.6.1.4.1.18642.1.1.1.22
Time on Saturday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect3Voltage 1.3.6.1.4.1.18642.1.1.1.23
Voltage which when exceeded will cause a specific load to disconnect. Return value is XXX representing XX.X volts.
OBJECT-TYPE    
  INTEGER  

disconnect3Temperature 1.3.6.1.4.1.18642.1.1.1.24
Temperature which when exceeded will cause a specific load to disconnect. Return value is XX representing XX C.
OBJECT-TYPE    
  INTEGER  

disconnect3LoadShedSundayOff 1.3.6.1.4.1.18642.1.1.1.25
Time on Sunday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect3LoadShedMondayOff 1.3.6.1.4.1.18642.1.1.1.26
Time on Monday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect3LoadShedTuesdayOff 1.3.6.1.4.1.18642.1.1.1.27
Time on Tuesday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect3LoadShedWednesdayOff 1.3.6.1.4.1.18642.1.1.1.28
Time on Wednesday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect3LoadShedThursdayOff 1.3.6.1.4.1.18642.1.1.1.29
Time on Thursday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect3LoadShedFridayOff 1.3.6.1.4.1.18642.1.1.1.30
Time on Friday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

disconnect3LoadShedSaturdayOff 1.3.6.1.4.1.18642.1.1.1.31
Time on Saturday which when reached will cause a specific load to disconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect1Voltage 1.3.6.1.4.1.18642.1.1.1.32
Voltage which when reached will cause a specific load to reconnect. Return value is XXX representing XX.X volts.
OBJECT-TYPE    
  INTEGER  

reconnect1LoadShedSundayOn 1.3.6.1.4.1.18642.1.1.1.33
Time which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect1LoadShedMondayOn 1.3.6.1.4.1.18642.1.1.1.34
Time on Monday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect1LoadShedTuesdayOn 1.3.6.1.4.1.18642.1.1.1.35
Time on Tuesday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect1LoadShedWednesdayOn 1.3.6.1.4.1.18642.1.1.1.36
Time on Wednesday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect1LoadShedThursdayOn 1.3.6.1.4.1.18642.1.1.1.37
Time on Thursday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect1LoadShedFridayOn 1.3.6.1.4.1.18642.1.1.1.38
Time on Friday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect1LoadShedSaturdayOn 1.3.6.1.4.1.18642.1.1.1.39
Time on Saturday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect2Voltage 1.3.6.1.4.1.18642.1.1.1.40
Voltage which when reached will cause a specific load to reconnect. Return value is XXX representing XX.X volts.
OBJECT-TYPE    
  INTEGER  

reconnect2LoadShedSundayOn 1.3.6.1.4.1.18642.1.1.1.41
Time on Sunday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect2LoadShedMondayOn 1.3.6.1.4.1.18642.1.1.1.42
Time on Monday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect2LoadShedTuesdayOn 1.3.6.1.4.1.18642.1.1.1.43
Time on Tuesday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect2LoadShedWednesdayOn 1.3.6.1.4.1.18642.1.1.1.44
Time on Wednesday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect2LoadShedThursdayOn 1.3.6.1.4.1.18642.1.1.1.45
Time on Thursday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect2LoadShedFridayOn 1.3.6.1.4.1.18642.1.1.1.46
Time on Friday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect2LoadShedSaturdayOn 1.3.6.1.4.1.18642.1.1.1.47
Time on Saturday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect3Voltage 1.3.6.1.4.1.18642.1.1.1.48
Voltage which when reached will cause a specific load to reconnect. Return value is XXX representing XX.X volts.
OBJECT-TYPE    
  INTEGER  

reconnect3LoadShedSundayOn 1.3.6.1.4.1.18642.1.1.1.49
Time on Sunday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect3LoadShedMondayOn 1.3.6.1.4.1.18642.1.1.1.50
Time on Monday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect3LoadShedTuesdayOn 1.3.6.1.4.1.18642.1.1.1.51
Time on Tuesday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect3LoadShedWednesdayOn 1.3.6.1.4.1.18642.1.1.1.52
Time on Wednesday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect3LoadShedThursdayOn 1.3.6.1.4.1.18642.1.1.1.53
Time on Thursday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect3LoadShedFridayOn 1.3.6.1.4.1.18642.1.1.1.54
Time on Friday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

reconnect3LoadShedSaturdayOn 1.3.6.1.4.1.18642.1.1.1.55
Time on Saturday which when reached will cause a specific load to reconnect. Return value is XX:XX representing HH:MM.
OBJECT-TYPE    
  DisplayString  

equalizeTime 1.3.6.1.4.1.18642.1.1.1.56
Number of hours the equalize voltage is to be applied. Return value is XXX representing XX.X hours.
OBJECT-TYPE    
  INTEGER  

equalizeVoltage 1.3.6.1.4.1.18642.1.1.1.57
Equalize voltage to be applied. Return value is XXX representing XX.X volts.
OBJECT-TYPE    
  INTEGER  

batteryResistancePercentChange 1.3.6.1.4.1.18642.1.1.1.58
Resistance percentange change that when reached will cause an alarm. Return value is XXX representing XXX %.
OBJECT-TYPE    
  INTEGER  

batteryResistanceTestInterval 1.3.6.1.4.1.18642.1.1.1.59
Battery resistance test interval. Return value is XX representing XX weeks.
OBJECT-TYPE    
  INTEGER  

loadShedTimeControl 1.3.6.1.4.1.18642.1.1.1.60
Load shed time control enabled/disabled status. Return value: 1 = time control enabled, 2 = time control disabled.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

batteryFloatCurrent 1.3.6.1.4.1.18642.1.1.1.61
Battery float current. Return value is XXX representing XXX amps.
OBJECT-TYPE    
  INTEGER  

readOnlyObjects 1.3.6.1.4.1.18642.1.2
OBJECT IDENTIFIER    

rectifiers 1.3.6.1.4.1.18642.1.2.1
OBJECT IDENTIFIER    

rectifierFloatVoltage 1.3.6.1.4.1.18642.1.2.1.1
Rectifier float voltage. Return value is XXX representing XX.X volts. Valid ranges are 24.0 to 57.0 volts.
OBJECT-TYPE    
  INTEGER  

rectifierLoadCurrent 1.3.6.1.4.1.18642.1.2.1.2
Rectifier DC load current. Return value is XXXX representing XXXX amps. Valid ranges are 0000 to 5000 amps.
OBJECT-TYPE    
  INTEGER  

batteries 1.3.6.1.4.1.18642.1.2.2
OBJECT IDENTIFIER    

batteryCurrent 1.3.6.1.4.1.18642.1.2.2.1
Battery current. Return value is XXXX representing XXXX amps. Valid ranges are 0000 to 1000 amps.
OBJECT-TYPE    
  INTEGER  

batteryTemperature 1.3.6.1.4.1.18642.1.2.2.2
Battery temperature. Return value is XX representing XX C. Valid ranges are -40 to 99 C.
OBJECT-TYPE    
  INTEGER  

batteryResistanceReference 1.3.6.1.4.1.18642.1.2.2.3
Initial battery resistance. Return value is XXXXX representing X.XXXX ohms. Valid ranges are 0.0000 to 5.0000 ohms.
OBJECT-TYPE    
  INTEGER  

batteryResistanceReading 1.3.6.1.4.1.18642.1.2.2.4
Last battery resistance reading. Return value is XXXXX representing X.XXXX ohms. Valid ranges are 0.0000 to 5.0000 ohms.
OBJECT-TYPE    
  INTEGER  

batteryResistanceChange 1.3.6.1.4.1.18642.1.2.2.5
Percent change from last battery resistance reading. Return value is XXX representing XXX %. Valid ranges are 001 to 999 %.
OBJECT-TYPE    
  INTEGER  

batteryCycles1 1.3.6.1.4.1.18642.1.2.2.6
Number of discharge/recharge cycles less than 1 minute. Return value is XXX representing XXX cycles. Valid ranges are 000 to 255 cycles.
OBJECT-TYPE    
  INTEGER  

batteryCycles1to5 1.3.6.1.4.1.18642.1.2.2.7
Number of discharge/recharge cycles from 1 to 5 minutes. Return value is XXX representing XXX cycles. Valid ranges are 000 to 255 cycles.
OBJECT-TYPE    
  INTEGER  

batteryCycles5to15 1.3.6.1.4.1.18642.1.2.2.8
Number of discharge/recharge cycles from 5 to 15 minutes. Return value is XXX representing XXX cycles. Valid ranges are 000 to 255 cycles.
OBJECT-TYPE    
  INTEGER  

batteryCycles15 1.3.6.1.4.1.18642.1.2.2.9
Number of discharge/recharge cycles greater than 15 minutes. Return value is XXX representing XXX cycles. Valid ranges are 000 to 255 cycles.
OBJECT-TYPE    
  INTEGER  

batteryCycles15LastCycleDate 1.3.6.1.4.1.18642.1.2.2.10
Last cycle date of batteryCycles15. Return value is MM-DD-YY, HH-MM.
OBJECT-TYPE    
  DisplayString  

batteryCycles15LastDuration 1.3.6.1.4.1.18642.1.2.2.11
Duration of batteryCycles15 last cycle. Return value is XXXX representing XXXX minutes.
OBJECT-TYPE    
  INTEGER  

batteryTestFault 1.3.6.1.4.1.18642.1.2.2.12
Battery failure has occured during battery restistance test. Return value: 1 = Abort 1, 2 = Abort 2, 3 = Abort 3, 4 = None.
OBJECT-TYPE    
  INTEGER abort1(1), abort2(2), abort3(3), none(4)  

factorySettings 1.3.6.1.4.1.18642.1.2.3
OBJECT IDENTIFIER    

floatVoltagePresets 1.3.6.1.4.1.18642.1.2.3.1
Float voltage factory setting range. Return value is XX.X volts min, XX.X volts max.
OBJECT-TYPE    
  DisplayString  

highVoltageAlarmPresets 1.3.6.1.4.1.18642.1.2.3.2
High voltage alarm factory setting range. Return value is XX.X volts min, XX.X volts max.
OBJECT-TYPE    
  DisplayString  

lowVoltageAlarmPresets 1.3.6.1.4.1.18642.1.2.3.3
Low voltage alarm factory setting range. Return value is XX.X volts min, XX.X volts max.
OBJECT-TYPE    
  DisplayString  

disconnect1VoltagePresets 1.3.6.1.4.1.18642.1.2.3.4
Disconnect voltage 1 factory setting range. Return value is XX.X volts min, XX.X volts max.
OBJECT-TYPE    
  DisplayString  

disconnect1TemperaturePreset 1.3.6.1.4.1.18642.1.2.3.5
Disconnect temperature 1 factory setting. Return value is XX C.
OBJECT-TYPE    
  DisplayString  

disconnect1LoadShedSundayPresets 1.3.6.1.4.1.18642.1.2.3.6
Disconnect 1 load shed Sunday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

disconnect1LoadShedMondayPresets 1.3.6.1.4.1.18642.1.2.3.7
Disconnect 1 load shed Monday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

disconnect1LoadShedTuesdayPresets 1.3.6.1.4.1.18642.1.2.3.8
Disconnect 1 load shed Tuesday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

disconnect1LoadShedWednesdayPresets 1.3.6.1.4.1.18642.1.2.3.9
Disconnect 1 load shed Wednesday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

disconnect1LoadShedThursdayPresets 1.3.6.1.4.1.18642.1.2.3.10
Disconnect 1 load shed Thursday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

disconnect1LoadShedFridayPresets 1.3.6.1.4.1.18642.1.2.3.11
Disconnect 1 load shed Friday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

disconnect1LoadShedSaturdayPresets 1.3.6.1.4.1.18642.1.2.3.12
Disconnect 1 load shed Saturday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

reconnectVoltage1Presets 1.3.6.1.4.1.18642.1.2.3.13
Reconnect voltage 1 factory setting range. Return value is XX.X volts min, XX.X volts max.
OBJECT-TYPE    
  DisplayString  

disconnect2VoltagePresets 1.3.6.1.4.1.18642.1.2.3.14
Disconnect voltage 2 factory setting range. Return value is XX.X volts min, XX.X volts max.
OBJECT-TYPE    
  DisplayString  

disconnect2TemperaturePreset 1.3.6.1.4.1.18642.1.2.3.15
Disconnect temperature 2 factory setting. Return value is XX C.
OBJECT-TYPE    
  DisplayString  

disconnect2LoadShedSundayPresets 1.3.6.1.4.1.18642.1.2.3.16
Disconnect 2 load shed Sunday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

disconnect2LoadShedMondayPresets 1.3.6.1.4.1.18642.1.2.3.17
Disconnect 2 load shed Monday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

disconnect2LoadShedTuesdayPresets 1.3.6.1.4.1.18642.1.2.3.18
Disconnect 2 load shed Tuesday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

disconnect2LoadShedWednesdayPresets 1.3.6.1.4.1.18642.1.2.3.19
Disconnect 2 load shed Wednesday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

disconnect2LoadShedThursdayPresets 1.3.6.1.4.1.18642.1.2.3.20
Disconnect 2 load shed Thursday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

disconnect2LoadShedFridayPresets 1.3.6.1.4.1.18642.1.2.3.21
Disconnect 2 load shed Friday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

disconnect2LoadShedSaturdayPresets 1.3.6.1.4.1.18642.1.2.3.22
Disconnect 2 load shed Saturday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

reconnect2VoltagePresets 1.3.6.1.4.1.18642.1.2.3.23
Reconnect voltage 2 factory setting range. Return value is XX.X volts min, XX.X volts max.
OBJECT-TYPE    
  DisplayString  

disconnect3VoltagePresets 1.3.6.1.4.1.18642.1.2.3.24
Disconnect voltage 3 factory setting range. Return value is XX.X volts min, XX.X volts max.
OBJECT-TYPE    
  DisplayString  

disconnect3TemperaturePreset 1.3.6.1.4.1.18642.1.2.3.25
Disconnect temperature 3 factory setting. Return value is XX C.
OBJECT-TYPE    
  DisplayString  

disconnect3LoadShedSundayPresets 1.3.6.1.4.1.18642.1.2.3.26
Disconnect 3 load shed Sunday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

disconnect3LoadShedMondayPresets 1.3.6.1.4.1.18642.1.2.3.27
Disconnect 3 load shed Monday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

disconnect3LoadShedTuesdayPresets 1.3.6.1.4.1.18642.1.2.3.28
Disconnect 3 load shed Tuesday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

disconnect3LoadShedWednesdayPresets 1.3.6.1.4.1.18642.1.2.3.29
Disconnect 3 load shed Wednesday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

disconnect3LoadShedThursdayPresets 1.3.6.1.4.1.18642.1.2.3.30
Disconnect 3 load shed Thursday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

disconnect3LoadShedFridayPresets 1.3.6.1.4.1.18642.1.2.3.31
Disconnect 3 load shed Friday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

disconnect3LoadShedSaturdayPresets 1.3.6.1.4.1.18642.1.2.3.32
Disconnect 3 load shed Saturday time settings. Return value is XX:Xx off, XX:XX on.
OBJECT-TYPE    
  DisplayString  

reconnect3VoltagePresets 1.3.6.1.4.1.18642.1.2.3.33
Reconnect voltage 3 factory setting range. Return value is XX.X volts min, XX.X volts max.
OBJECT-TYPE    
  DisplayString  

overloadCurrentPresets 1.3.6.1.4.1.18642.1.2.3.34
Overload current factory setting range. Return value is XXXX amps min, XXXX amps max.
OBJECT-TYPE    
  DisplayString  

maximumCurrentPreset 1.3.6.1.4.1.18642.1.2.3.35
Maximum current factory setting. Return value is XXXX amps.
OBJECT-TYPE    
  DisplayString  

batteryFloatCurrentPresets 1.3.6.1.4.1.18642.1.2.3.36
Battery float current factory settings. Return value is XXX amps min, XXX amps max.
OBJECT-TYPE    
  DisplayString  

equalizeTimePresets 1.3.6.1.4.1.18642.1.2.3.37
Equalize time factory setting range. Return value is 00.0 hours min, XX.X hours max.
OBJECT-TYPE    
  DisplayString  

equalizeVoltagePresets 1.3.6.1.4.1.18642.1.2.3.38
Equalize voltage factory setting range. Return value is XX.X volts min, XX.X volts max.
OBJECT-TYPE    
  DisplayString  

batteryResistancePresets 1.3.6.1.4.1.18642.1.2.3.39
Battery resistance percent change factory setting range. Return value is XXX % min, XXX % max.
OBJECT-TYPE    
  DisplayString  

batteryTestIntervalPresets 1.3.6.1.4.1.18642.1.2.3.40
Battery resistance test interval factory setting range. Return value is XX weeks min, XX weeks max.
OBJECT-TYPE    
  DisplayString  

alarmStatus 1.3.6.1.4.1.18642.1.2.4
OBJECT IDENTIFIER    

highVoltageAlarmStatus 1.3.6.1.4.1.18642.1.2.4.1
High voltage alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

lowVoltageAlarmStatus 1.3.6.1.4.1.18642.1.2.4.2
Low voltage alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

overloadAlarmStatus 1.3.6.1.4.1.18642.1.2.4.3
Overload alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

breakerAlarmStatus 1.3.6.1.4.1.18642.1.2.4.4
Breaker alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

acFailureAlarmStatus 1.3.6.1.4.1.18642.1.2.4.5
AC failure alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

fanFailureAlarmStatus 1.3.6.1.4.1.18642.1.2.4.6
Fan failure alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

rectifierFailureAlarmStatus 1.3.6.1.4.1.18642.1.2.4.7
Rectifier failure alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

majorAlarmStatus 1.3.6.1.4.1.18642.1.2.4.8
Major alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

lowVoltageDisconnect1TemperatureAlarmStatus 1.3.6.1.4.1.18642.1.2.4.9
Low voltage disconnect 1 high temperature alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

lowVoltageDisconnect2TemperatureAlarmStatus 1.3.6.1.4.1.18642.1.2.4.10
Low voltage disconnect 2 high temperature alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

lowVoltageDisconnect3TemperatureAlarmStatus 1.3.6.1.4.1.18642.1.2.4.11
Low voltage disconnect 3 high temperature alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

lowVoltageDisconnect1VoltageAlarmStatus 1.3.6.1.4.1.18642.1.2.4.12
Low voltage disconnect 1 low voltage alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

lowVoltageDisconnect2VoltageAlarmStatus 1.3.6.1.4.1.18642.1.2.4.13
Low voltage disconnect 2 low voltage alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

lowVoltageDisconnect3VoltageAlarmStatus 1.3.6.1.4.1.18642.1.2.4.14
Low voltage disconnect 3 low voltage alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

batteryResistanceAlarmStatus 1.3.6.1.4.1.18642.1.2.4.15
Battery resistance alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

batteryCurrentAlarmStatus 1.3.6.1.4.1.18642.1.2.4.16
Battery resistance alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

batteryTestAbortCondition1AlarmStatus 1.3.6.1.4.1.18642.1.2.4.17
Battery test abort condition 1 alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

batteryTestAbortCondition2AlarmStatus 1.3.6.1.4.1.18642.1.2.4.18
Battery test abort condition 2 alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

batteryTestAbortCondition3AlarmStatus 1.3.6.1.4.1.18642.1.2.4.19
Battery test abort condition 3 alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

batteryDisconnectAlarmStatus 1.3.6.1.4.1.18642.1.2.4.20
Battery disconnect alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

fuseAlarmStatus 1.3.6.1.4.1.18642.1.2.4.21
Fuse alarm status. Return value 1 = alarm inactive, 2 = alarm active.
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

digitalSensorAlarms 1.3.6.1.4.1.18642.1.2.5
OBJECT IDENTIFIER    

systemAlarms 1.3.6.1.4.1.18642.1.2.6
OBJECT IDENTIFIER    

digitalSensorAlarmClears 1.3.6.1.4.1.18642.1.2.7
OBJECT IDENTIFIER    

systemAlarmClears 1.3.6.1.4.1.18642.1.2.8
OBJECT IDENTIFIER