CADANT-CMTS-POLICY-MIB

File: CADANT-CMTS-POLICY-MIB.mib (67942 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMP-FRAMEWORK-MIB
CADANT-PRODUCTS-MIB CADANT-TC IF-MIB
INET-ADDRESS-MIB DC-RTM-MIB

Imported symbols

OBJECT-TYPE MODULE-IDENTITY Integer32
Unsigned32 IpAddress Counter32
Counter64 TruthValue RowStatus
TimeStamp MacAddress TEXTUAL-CONVENTION
SnmpAdminString cadPolicy CadExtAclCondition
CadIfDirection CadIpTos CadIpTosMask
CadTcpFlags CadAclType CadProtocolType
CadAclString InetAddressIPv4or6 InterfaceIndex
InetAddressType InetAddress InfoSourceDest

Defined Types

CadPolicyRateLimitAction  
Enumeration of rate limiting actions
TEXTUAL-CONVENTION    
  INTEGER transmit(1), drop(2), set-prec-transmit(3), set-dscp-transmit(4), set-priority-transmit(5)  

CadPolicyAction  
Action to be taken for Policy Policy Permit(1) Policy Deny (2)
TEXTUAL-CONVENTION    
  Integer32 1..2  

CadPolicyProtocol  
A value that represents a type of the protocol.
TEXTUAL-CONVENTION    
  INTEGER other(1), local(2), netmgmt(3), icmp(4), egp(5), ggp(6), hello(7), rip(8), isIs(9), esIs(10), ciscoIgrp(11), bbnSpfIgp(12), ospf(13), bgp(14), idpr(15), ciscoEigrp(16)  

CadScmAccessEntry  
SEQUENCE    
  cadScmAccIfIndex InterfaceIndex
  cadScmAccListNumber Integer32
  cadScmAccRowStatus RowStatus

CadDistListInEntry  
SEQUENCE    
  cadDistListInProtocol CadPolicyProtocol
  cadDistListInProtocolProcess Integer32
  cadDistListInIfIndex InterfaceIndex
  cadDistListInAccessListNum Integer32
  cadDistListInAccessListName OCTET STRING
  cadDistListInStatus RowStatus

CadPolicyRateLimitEntry  
SEQUENCE    
  cadPolicyRateLimitIfIndex InterfaceIndex
  cadPolicyRateLimitDirection CadIfDirection
  cadPolicyRateLimitIndex INTEGER
  cadPolicyRateLimitStatus RowStatus
  cadPolicyRateLimitAclType CadAclType
  cadPolicyRateLimitAclNum Integer32
  cadPolicyRateLimitBps Integer32
  cadPolicyRateLimitBurstNormal Integer32
  cadPolicyRateLimitBurstMax Integer32
  cadPolicyRateLimitConformAction CadPolicyRateLimitAction
  cadPolicyRateLimitConformValue INTEGER
  cadPolicyRateLimitExceedAction CadPolicyRateLimitAction
  cadPolicyRateLimitExceedValue INTEGER
  cadPolicyRateLimitClearCounts TruthValue

CadPolicyRateLimitStatusEntry  
SEQUENCE    
  cadPolicyRateLimitConformPackets Counter64
  cadPolicyRateLimitConformBytes Counter64
  cadPolicyRateLimitExceedPackets Counter64
  cadPolicyRateLimitExceedBytes Counter64
  cadPolicyRateLimitCurrentBurst Integer32
  cadPolicyRateLimitLastCleared TimeStamp

CadPolicyAclEntry  
SEQUENCE    
  cadAclNumber Integer32
  cadAclIndex Integer32
  cadAclType CadAclType
  cadAclStatus RowStatus
  cadAclPermit TruthValue
  cadAclProtocol CadProtocolType
  cadAclSrcIp InetAddressIPv4or6
  cadAclSrcIpMask InetAddressIPv4or6
  cadAclSrcPortOp CadExtAclCondition
  cadAclSrcPortLo Integer32
  cadAclSrcPortHi Integer32
  cadAclDstIp InetAddressIPv4or6
  cadAclDstIpMask InetAddressIPv4or6
  cadAclDstPortOp CadExtAclCondition
  cadAclDstPortLo Integer32
  cadAclDstPortHi Integer32
  cadAclProtoType Integer32
  cadAclLogging TruthValue
  cadAclProtoCode Integer32
  cadAclIpTos CadIpTos
  cadAclIpTosMask CadIpTosMask
  cadAclTcpFlags CadTcpFlags
  cadAclTcpFlagsMask CadTcpFlags
  cadAclFragments TruthValue
  cadAclRemark CadAclString
  cadAclIpAddrType InetAddressType

CadSnmpCommAccessEntry  
SEQUENCE    
  cadSnmpCommAccessName SnmpAdminString
  cadSnmpCommAccessList Integer32
  cadSnmpCommAccessStatus RowStatus

CadPolicyAccessGroupEntry  
SEQUENCE    
  cadPolicyAccessGroupIfIndex InterfaceIndex
  cadPolicyAccessGroupDirection CadIfDirection
  cadPolicyAccessGroupStatus RowStatus
  cadPolicyAccessGroupIpv4AclNum Integer32
  cadPolicyAccessGroupClearCounts TruthValue
  cadPolicyAccessGroupIpv6AclNum Integer32
  cadPolicyAccessGroupIpv6AclName SnmpAdminString

CadPolicyAccessGroupStatusEntry  
SEQUENCE    
  cadPolicyAccessGroupPermitPackets Counter64
  cadPolicyAccessGroupDenyPackets Counter64
  cadPolicyAccessGroupLastCleared TimeStamp

CadPolicyPfxListEntry  
SEQUENCE    
  cadPolicyPfxListNumber Integer32
  cadPolicyPfxListName OCTET STRING
  cadPolicyPfxListSeqNumber Integer32
  cadPolicyPfxListIpAddress InetAddress
  cadPolicyPfxListIpAddMaskLen Integer32
  cadPolicyPfxListMaskGeValue Integer32
  cadPolicyPfxListMaskLeValue Integer32
  cadPolicyPfxListAction CadPolicyAction
  cadPolicyPfxListStatus RowStatus
  cadPolicyPfxListAfi InetAddressType
  cadPolicyPfxListSafi INTEGER

CadPolicyDistListOutEntry  
SEQUENCE    
  cadPolicyDistListOutSrcProtocol CadPolicyProtocol
  cadPolicyDistListOutSrcProtocolProcess Integer32
  cadPolicyDistListOutRoutingProtocol CadPolicyProtocol
  cadPolicyDistListOutRoutingProcess Integer32
  cadPolicyDistListOutAutonomousSystemNum Integer32
  cadPolicyDistListOutAccessListNum Integer32
  cadPolicyDistListOutAccessListName OCTET STRING
  cadPolicyDistListOutStatus RowStatus
  cadPolicyDistListOutIfIndex InterfaceIndex

CadDistListOutEntry  
SEQUENCE    
  cadDistListOutVrIndex Integer32
  cadDistListOutDestProtocol InfoSourceDest
  cadDistListOutSrcProtocol InfoSourceDest
  cadDistListOutAccessListNum Integer32
  cadDistListOutStatus RowStatus
  cadDistListOutAccessListName SnmpAdminString

CadAclNameEntry  
SEQUENCE    
  cadNameAclName SnmpAdminString
  cadNameAclNumber Integer32
  cadNameAclStatus RowStatus

CadPolicyAclExtEntry  
SEQUENCE    
  cadAclEntryCount Counter64

CadRouteMapTagEntry  
SEQUENCE    
  cadRouteMapTagName SnmpAdminString
  cadRouteMapTagId Integer32
  cadRouteMapTagRowStatus RowStatus

CadRouteMapEntry  
SEQUENCE    
  cadRouteMapId Integer32
  cadRouteMapSeqNum Integer32
  cadRouteMapMatchType INTEGER
  cadRouteMapMatchAcl Integer32
  cadRouteMapSetIpPrec TruthValue
  cadRouteMapIpPrec INTEGER
  cadRouteMapSetIpTos TruthValue
  cadRouteMapIpTos INTEGER
  cadRouteMapSetNextHop TruthValue
  cadRouteMapNextHopAddrType InetAddressType
  cadRouteMapNextHop InetAddress
  cadRouteMapSetBackupNextHop TruthValue
  cadRouteMapBackupNextHop InetAddress
  cadRouteMapSetNullInterface TruthValue
  cadRouteMapRowStatus RowStatus
  cadRouteMapSetIpDscp TruthValue
  cadRouteMapIpDscp INTEGER
  cadRouteMapSetRecursiveNextHop TruthValue
  cadRouteMapRecursiveNextHop InetAddress

CadRouteMapStatsEntry  
SEQUENCE    
  cadRouteMapPktMatched Counter32
  cadRouteMapByteMatched Counter64
  cadRouteMapPktFailed Counter32
  cadRouteMapByteFailed Counter64

Defined Values

cadPolicyMib 6.4.1.4998.1.1.35.1
Arris Cadant C4 CMTS policy parameters and constants
MODULE-IDENTITY    

cadScmAccessTable 6.4.1.4998.1.1.35.1.1
A table contains SCM access control list information. Each physical interface is associated with the access list number defined as hjpolAccListNumber in hjpolAccListTable of NETPLANE-POLICY-MIB. With this information, C4 can permit/deny access usnig access list filtering before the packet reach SCM from the specified physical interface.
OBJECT-TYPE    
  SEQUENCE OF  
    CadScmAccessEntry

cadScmAccessEntry 6.4.1.4998.1.1.35.1.1.1
A conceptual row containing information about SCM access list for each physical interface.
OBJECT-TYPE    
  CadScmAccessEntry  

cadScmAccIfIndex 6.4.1.4998.1.1.35.1.1.1.1
The value of this object identifies a physical layer2 interface, such as a DOCSIS MAC or a Gigabit/TenGigabit NAM, on which SCM access control is applied
OBJECT-TYPE    
  InterfaceIndex  

cadScmAccListNumber 6.4.1.4998.1.1.35.1.1.1.2
The value of this object identifies entry(or entries) in the hjpolAccListTable. The identified entry(or entries) contains SCM access parameters to be used when filtering traffic from individual interface sent to SCM.
OBJECT-TYPE    
  Integer32 1..99  

cadScmAccRowStatus 6.4.1.4998.1.1.35.1.1.1.3
Control Object for row creation and deletion.
OBJECT-TYPE    
  RowStatus  

cadDistListInTable 6.4.1.4998.1.1.35.1.2
Distribute List In Table
OBJECT-TYPE    
  SEQUENCE OF  
    CadDistListInEntry

cadDistListInEntry 6.4.1.4998.1.1.35.1.2.1
A row in Distribute List In table
OBJECT-TYPE    
  CadDistListInEntry  

cadDistListInProtocol 6.4.1.4998.1.1.35.1.2.1.1
Protocol for which distribute list is applied.
OBJECT-TYPE    
  CadPolicyProtocol  

cadDistListInProtocolProcess 6.4.1.4998.1.1.35.1.2.1.2
VRF for which distribute list is applied.
OBJECT-TYPE    
  Integer32 1..2147483647  

cadDistListInIfIndex 6.4.1.4998.1.1.35.1.2.1.3
Interface for which distribute list is applied. The value will be 1 if the distribute list is applied to all interfaces.
OBJECT-TYPE    
  InterfaceIndex  

cadDistListInAccessListNum 6.4.1.4998.1.1.35.1.2.1.4
The configured distribute in list refers to the access list specified.
OBJECT-TYPE    
  Integer32 1..99  

cadDistListInAccessListName 6.4.1.4998.1.1.35.1.2.1.5
Name of the access list referred by distribute in list.
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

cadDistListInStatus 6.4.1.4998.1.1.35.1.2.1.6
The row status variable, used according to row installation and removal conventions. Once access list specified default row status is active.
OBJECT-TYPE    
  RowStatus  

cadPolicyRateLimitTable 6.4.1.4998.1.1.35.1.4
A table of rate limiting policies applied to a physical interface.
OBJECT-TYPE    
  SEQUENCE OF  
    CadPolicyRateLimitEntry

cadPolicyRateLimitEntry 6.4.1.4998.1.1.35.1.4.1
An ordered list of the rate limit polices
OBJECT-TYPE    
  CadPolicyRateLimitEntry  

cadPolicyRateLimitIfIndex 6.4.1.4998.1.1.35.1.4.1.1
The value of this object identifies a physical layer2 interface, such as a DOCSIS MAC or a Gigabit/TenGigabit NAM, on which the rate limit policy is applied
OBJECT-TYPE    
  InterfaceIndex  

cadPolicyRateLimitDirection 6.4.1.4998.1.1.35.1.4.1.2
Direction of traffic on interface to apply the rate limit policy
OBJECT-TYPE    
  CadIfDirection  

cadPolicyRateLimitIndex 6.4.1.4998.1.1.35.1.4.1.3
Index of rate limit policy. Policies are applied in the order specified by this index value
OBJECT-TYPE    
  INTEGER 1..2  

cadPolicyRateLimitStatus 6.4.1.4998.1.1.35.1.4.1.4
Create and delete table row entries.
OBJECT-TYPE    
  RowStatus  

cadPolicyRateLimitAclType 6.4.1.4998.1.1.35.1.4.1.5
Type of ACL associated with rate limit policy
OBJECT-TYPE    
  CadAclType  

cadPolicyRateLimitAclNum 6.4.1.4998.1.1.35.1.4.1.6
ACL number. If the ACL does not exist, then this is treated as if the ACL type is none, i.e. all IP traffic matches the policy.
OBJECT-TYPE    
  Integer32  

cadPolicyRateLimitBps 6.4.1.4998.1.1.35.1.4.1.7
Average rate, in bits per second (bps).
OBJECT-TYPE    
  Integer32  

cadPolicyRateLimitBurstNormal 6.4.1.4998.1.1.35.1.4.1.8
Normal burst size, in bytes. The minimum value is bps divided by 2000.
OBJECT-TYPE    
  Integer32  

cadPolicyRateLimitBurstMax 6.4.1.4998.1.1.35.1.4.1.9
Excess burst size, in bytes. Must be equal to or larger than cadPolicyRateLimitBurstNormal
OBJECT-TYPE    
  Integer32  

cadPolicyRateLimitConformAction 6.4.1.4998.1.1.35.1.4.1.10
Action to take on packets that conform to the specified rate limit.
OBJECT-TYPE    
  CadPolicyRateLimitAction  

cadPolicyRateLimitConformValue 6.4.1.4998.1.1.35.1.4.1.11
Value to set if action is set-prec-transmit, set-dscp-transmit or set-priority-transmit. For set-priority-transmit,the valid value range is 0-7.
OBJECT-TYPE    
  INTEGER 0..255  

cadPolicyRateLimitExceedAction 6.4.1.4998.1.1.35.1.4.1.12
Action to take on packets that exceed to the specified rate limit.
OBJECT-TYPE    
  CadPolicyRateLimitAction  

cadPolicyRateLimitExceedValue 6.4.1.4998.1.1.35.1.4.1.13
Value to set if action is set-prec-transmit, set-dscp-transmit or set-priority-transmit. For set-priority-transmit,the valid value range is 0-7.
OBJECT-TYPE    
  INTEGER 0..255  

cadPolicyRateLimitClearCounts 6.4.1.4998.1.1.35.1.4.1.14
If set to true, clear the counts in the CadPolicyRateLimitStatusEntry. When read, this field always returns false. The correct way to clear the counts is to first read them, then set ClearCounts to true.
OBJECT-TYPE    
  TruthValue  

cadPolicyRateLimitStatusTable 6.4.1.4998.1.1.35.1.5
A table of counts of rate limiting policies applied to a physical interface.
OBJECT-TYPE    
  SEQUENCE OF  
    CadPolicyRateLimitStatusEntry

cadPolicyRateLimitStatusEntry 6.4.1.4998.1.1.35.1.5.1
Dyanmic status associated with a rate limit policy
OBJECT-TYPE    
  CadPolicyRateLimitStatusEntry  

cadPolicyRateLimitConformPackets 6.4.1.4998.1.1.35.1.5.1.1
Number of packets conforming to the policy rate
OBJECT-TYPE    
  Counter64  

cadPolicyRateLimitConformBytes 6.4.1.4998.1.1.35.1.5.1.2
Number of bytes conforming to the policy rate
OBJECT-TYPE    
  Counter64  

cadPolicyRateLimitExceedPackets 6.4.1.4998.1.1.35.1.5.1.3
Number of packets exceeding to the policy rate
OBJECT-TYPE    
  Counter64  

cadPolicyRateLimitExceedBytes 6.4.1.4998.1.1.35.1.5.1.4
Number of bytes exceeding to the policy rate
OBJECT-TYPE    
  Counter64  

cadPolicyRateLimitCurrentBurst 6.4.1.4998.1.1.35.1.5.1.5
The current number of bytes in the burst exceeding the average bps rate
OBJECT-TYPE    
  Integer32  

cadPolicyRateLimitLastCleared 6.4.1.4998.1.1.35.1.5.1.6
The value of SysUptime when the rate limit counters were last cleared.
OBJECT-TYPE    
  TimeStamp  

cadPolicyAclTable 6.4.1.4998.1.1.35.1.6
A table contains access control list (ACL) information. Each row corresponds to an access control entry (ACE), and each ACL may have multiple ACEs that are applied in order to the packet being inspected.
OBJECT-TYPE    
  SEQUENCE OF  
    CadPolicyAclEntry

cadPolicyAclEntry 6.4.1.4998.1.1.35.1.6.1
A conceptual row containing information about SCM access list for each physical interface.
OBJECT-TYPE    
  CadPolicyAclEntry  

cadAclNumber 6.4.1.4998.1.1.35.1.6.1.1
IPv6 ACL number. IPv6 ACLs are in the range 200-399. Extended ACL number. Extended ACLs are in the range 100-199. Standard ACLs are in the range 1-99.
OBJECT-TYPE    
  Integer32 1..399  

cadAclIndex 6.4.1.4998.1.1.35.1.6.1.2
Order in which this ACE is used in the ACL.
OBJECT-TYPE    
  Integer32 1..2147483647  

cadAclType 6.4.1.4998.1.1.35.1.6.1.3
Indicates whether this EACE is used as a standard, extended, or remark ACL. The rate-limiting type is not valid for this table. Remark is the only valid type that can be set, standard and extended are set by the agent when the ACE is created.
OBJECT-TYPE    
  CadAclType  

cadAclStatus 6.4.1.4998.1.1.35.1.6.1.4
RowStatus used to add and remove ACEs. ACEs that contain only remarks should have their status set to notInService and should be created with createAndWait.
OBJECT-TYPE    
  RowStatus  

cadAclPermit 6.4.1.4998.1.1.35.1.6.1.5
Permit or Deny the packet when matched.
OBJECT-TYPE    
  TruthValue  

cadAclProtocol 6.4.1.4998.1.1.35.1.6.1.6
Protocol number to match
OBJECT-TYPE    
  CadProtocolType  

cadAclSrcIp 6.4.1.4998.1.1.35.1.6.1.7
Source IP address to match
OBJECT-TYPE    
  InetAddressIPv4or6  

cadAclSrcIpMask 6.4.1.4998.1.1.35.1.6.1.8
Source IP wildcard mask to match. Default to match anything
OBJECT-TYPE    
  InetAddressIPv4or6  

cadAclSrcPortOp 6.4.1.4998.1.1.35.1.6.1.9
Source port condition (lt,gt,eq,ne) to match.
OBJECT-TYPE    
  CadExtAclCondition  

cadAclSrcPortLo 6.4.1.4998.1.1.35.1.6.1.10
First Source port number to match. -1 indicates that this field is not used.
OBJECT-TYPE    
  Integer32  

cadAclSrcPortHi 6.4.1.4998.1.1.35.1.6.1.11
Second Source port number to match. -1 indicates that this field is not used.
OBJECT-TYPE    
  Integer32  

cadAclDstIp 6.4.1.4998.1.1.35.1.6.1.12
Destination IP address to match
OBJECT-TYPE    
  InetAddressIPv4or6  

cadAclDstIpMask 6.4.1.4998.1.1.35.1.6.1.13
Destination IP wildcard (inverse) mask to match. Default to match anything.
OBJECT-TYPE    
  InetAddressIPv4or6  

cadAclDstPortOp 6.4.1.4998.1.1.35.1.6.1.14
Destination port condition (lt,gt,eq,ne) to match.
OBJECT-TYPE    
  CadExtAclCondition  

cadAclDstPortLo 6.4.1.4998.1.1.35.1.6.1.15
First Destination port number to match. -1 indicates that this field is not used.
OBJECT-TYPE    
  Integer32  

cadAclDstPortHi 6.4.1.4998.1.1.35.1.6.1.16
Second Destination port number to match. -1 indicates that this field is not used
OBJECT-TYPE    
  Integer32  

cadAclLogging 6.4.1.4998.1.1.35.1.6.1.17
Turn on or off the ACE matching log
OBJECT-TYPE    
  TruthValue  

cadAclProtoType 6.4.1.4998.1.1.35.1.6.1.18
Sub-protocol qualifiers. For protocol type ICMP, this value matches the ICMP message type (0 - 255). For IGMP, this value matches the IGMP message type (0-15). A value of -1 means that this field is not used.
OBJECT-TYPE    
  Integer32  

cadAclProtoCode 6.4.1.4998.1.1.35.1.6.1.19
Sub-protocol qualifiers. For protocol type ICMP, this value matches the ICMP message type code (0 - 255). A value of -1 indicates this value is not used.
OBJECT-TYPE    
  Integer32  

cadAclIpTos 6.4.1.4998.1.1.35.1.6.1.20
Matches the TOS field of the IP header.
OBJECT-TYPE    
  CadIpTos  

cadAclIpTosMask 6.4.1.4998.1.1.35.1.6.1.21
Mask to apply to the IpTos object when finding a mactch on the TOS field of the IP header. A value of 0 is used to indicate that the TOS is not used.
OBJECT-TYPE    
  CadIpTosMask  

cadAclTcpFlags 6.4.1.4998.1.1.35.1.6.1.22
Matches the flags field of the TCP header.
OBJECT-TYPE    
  CadTcpFlags  

cadAclTcpFlagsMask 6.4.1.4998.1.1.35.1.6.1.23
Mask to apply to the TcpFlags object when finding a mactch on the flags field of the TCP header.
OBJECT-TYPE    
  CadTcpFlags  

cadAclFragments 6.4.1.4998.1.1.35.1.6.1.24
Indicates whether this EACE applies to noninitial fragments of packets. The default is disabled.
OBJECT-TYPE    
  TruthValue  

cadAclRemark 6.4.1.4998.1.1.35.1.6.1.26
The comment associated with the access control entry. This is only valid for ACEs of type remark.
OBJECT-TYPE    
  CadAclString  

cadAclIpAddrType 6.4.1.4998.1.1.35.1.6.1.27
IP Address type
OBJECT-TYPE    
  InetAddressType  

cadSnmpCommAccessTable 6.4.1.4998.1.1.35.1.7
A table contains the access list information associated with the community string. Each community string defined in snmpCommunithTable can be configured with one access list number. C4 can permit/deny access usnig access list filtering. Filtering will occur in software, after the SNMP traffic passed through the OSE protocol stack and received by the agent. Standard ACLs will be used to enforce the access restrictions
OBJECT-TYPE    
  SEQUENCE OF  
    CadSnmpCommAccessEntry

cadSnmpCommAccessEntry 6.4.1.4998.1.1.35.1.7.1
A conceptual row containing information about access list filtering associated with community string.
OBJECT-TYPE    
  CadSnmpCommAccessEntry  

cadSnmpCommAccessName 6.4.1.4998.1.1.35.1.7.1.1
The index value that uniquely identifies an entry in snmpCommunityTable.
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

cadSnmpCommAccessList 6.4.1.4998.1.1.35.1.7.1.2
The value of this object identifies entry (or entries) in the cadPolicyAclTable. The identified entry (or entries) contains access parameters to be used when filtering traffic sent to SNMP agent.
OBJECT-TYPE    
  Integer32 1..99  

cadSnmpCommAccessStatus 6.4.1.4998.1.1.35.1.7.1.3
Control Object for row creation and deletion.
OBJECT-TYPE    
  RowStatus  

cadPolicyAccessGroupTable 6.4.1.4998.1.1.35.1.8
A table of access group policies applied to a physical interface.
OBJECT-TYPE    
  SEQUENCE OF  
    CadPolicyAccessGroupEntry

cadPolicyAccessGroupEntry 6.4.1.4998.1.1.35.1.8.1
An ordered list of the access group polices
OBJECT-TYPE    
  CadPolicyAccessGroupEntry  

cadPolicyAccessGroupIfIndex 6.4.1.4998.1.1.35.1.8.1.1
The value of this object identifies a physical layer2 interface, such as a DOCSIS MAC or a Gigabit/TenGigabit NAM, on which the access group policy is applied
OBJECT-TYPE    
  InterfaceIndex  

cadPolicyAccessGroupDirection 6.4.1.4998.1.1.35.1.8.1.2
Direction of traffic on interface to apply the access group policy
OBJECT-TYPE    
  CadIfDirection  

cadPolicyAccessGroupStatus 6.4.1.4998.1.1.35.1.8.1.3
This table supports sets of createAndGo(4) and destroy(6)
OBJECT-TYPE    
  RowStatus  

cadPolicyAccessGroupIpv4AclNum 6.4.1.4998.1.1.35.1.8.1.4
ACL number. If the ACL does not exist, then this is treated as if the ACL type is none, i.e. all IPv4 traffic matches the policy.
OBJECT-TYPE    
  Integer32  

cadPolicyAccessGroupClearCounts 6.4.1.4998.1.1.35.1.8.1.5
If set to true, clear the counts in the CadPolicyAccessGroupStatusEntry. When read, this field always returns false. The correct way to clear the counts is to first read them, then set ClearCounts to true.
OBJECT-TYPE    
  TruthValue  

cadPolicyAccessGroupIpv6AclNum 6.4.1.4998.1.1.35.1.8.1.6
ACL number. If the ACL does not exist, then this is treated as if the ACL type is none, i.e. all IPv6 traffic matches the policy.
OBJECT-TYPE    
  Integer32  

cadPolicyAccessGroupIpv6AclName 6.4.1.4998.1.1.35.1.8.1.7
ACL name.
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

cadPolicyAccessGroupStatusTable 6.4.1.4998.1.1.35.1.9
A table of counts of rate limiting policies applied to a physical interface.
OBJECT-TYPE    
  SEQUENCE OF  
    CadPolicyAccessGroupStatusEntry

cadPolicyAccessGroupStatusEntry 6.4.1.4998.1.1.35.1.9.1
Dyanmic status associated with a rate limit policy
OBJECT-TYPE    
  CadPolicyAccessGroupStatusEntry  

cadPolicyAccessGroupPermitPackets 6.4.1.4998.1.1.35.1.9.1.1
Number of packets conforming to the access group policy permit ACL
OBJECT-TYPE    
  Counter64  

cadPolicyAccessGroupDenyPackets 6.4.1.4998.1.1.35.1.9.1.2
Number of packets conforming to the access group policy deny ACL
OBJECT-TYPE    
  Counter64  

cadPolicyAccessGroupLastCleared 6.4.1.4998.1.1.35.1.9.1.3
The value of SysUptime when the access group policy counters were last cleared.
OBJECT-TYPE    
  TimeStamp  

cadPolicyPfxListTable 6.4.1.4998.1.1.35.1.11
Prefix List Table
OBJECT-TYPE    
  SEQUENCE OF  
    CadPolicyPfxListEntry

cadPolicyPfxListEntry 6.4.1.4998.1.1.35.1.11.1
A row in Prefix list table
OBJECT-TYPE    
  CadPolicyPfxListEntry  

cadPolicyPfxListNumber 6.4.1.4998.1.1.35.1.11.1.1
Prefix list is identified by number value of 0 should be passed for this object if prefix list is configured by name
OBJECT-TYPE    
  Integer32 0..2147483647  

cadPolicyPfxListName 6.4.1.4998.1.1.35.1.11.1.2
Name of prefix list.Null value is assigned to this Object if the prefix list is identified by number
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

cadPolicyPfxListSeqNumber 6.4.1.4998.1.1.35.1.11.1.3
A sequence in the prefix list is identified by sequence number. If no sequence is specified defalut sequence of 5 is assumend. IF one more sequence is configured sequence number 10 is assigned (multiples of 5)
OBJECT-TYPE    
  Integer32 5..2147483645  

cadPolicyPfxListIpAddress 6.4.1.4998.1.1.35.1.11.1.4
This is the source ipv4 or ipv6 address on which the filtering needs to be applied
OBJECT-TYPE    
  InetAddress  

cadPolicyPfxListIpAddMaskLen 6.4.1.4998.1.1.35.1.11.1.5
Mask length of the Source IP address
OBJECT-TYPE    
  Integer32 0..32  

cadPolicyPfxListMaskGeValue 6.4.1.4998.1.1.35.1.11.1.6
If the received route matches the source address and the mask length is greater than the value specified, apply the specified action to the route
OBJECT-TYPE    
  Integer32 0..32  

cadPolicyPfxListMaskLeValue 6.4.1.4998.1.1.35.1.11.1.7
This value specifies if the received route mask length is less the value specified here do the action specified (permit/deny)
OBJECT-TYPE    
  Integer32 0..32  

cadPolicyPfxListAction 6.4.1.4998.1.1.35.1.11.1.8
specifies the action to be taken. Possible actions include permit(1) and deny(2)
OBJECT-TYPE    
  CadPolicyAction  

cadPolicyPfxListStatus 6.4.1.4998.1.1.35.1.11.1.9
The row status variable, used according to row installation and removal conventions.
OBJECT-TYPE    
  RowStatus  

cadPolicyPfxListAfi 6.4.1.4998.1.1.35.1.11.1.10
This is the Address Family Identifier (AFI) of the prefix that will follow. Only IPv4 or IPv6 prefix-list will be supported.
OBJECT-TYPE    
  InetAddressType  

cadPolicyPfxListSafi 6.4.1.4998.1.1.35.1.11.1.11
This is the Subsequent Address Family Identifier (SAFI) of the prefix that will follow.
OBJECT-TYPE    
  INTEGER unicast(1), multicast(2), both(3), mplsBgpVpn(128)  

cadPolicyDistListOutTable 6.4.1.4998.1.1.35.1.12
Distribute List Out Table
OBJECT-TYPE    
  SEQUENCE OF  
    CadPolicyDistListOutEntry

cadPolicyDistListOutEntry 6.4.1.4998.1.1.35.1.12.1
A row in Distribute List Out table
OBJECT-TYPE    
  CadPolicyDistListOutEntry  

cadPolicyDistListOutSrcProtocol 6.4.1.4998.1.1.35.1.12.1.1
Source Protocol under which distribute list is configured.
OBJECT-TYPE    
  CadPolicyProtocol  

cadPolicyDistListOutSrcProtocolProcess 6.4.1.4998.1.1.35.1.12.1.2
Source VRF ID under which distribute list is configured.
OBJECT-TYPE    
  Integer32 1..2147483647  

cadPolicyDistListOutRoutingProtocol 6.4.1.4998.1.1.35.1.12.1.3
Destination Protocol to which routes need to be sent.
OBJECT-TYPE    
  CadPolicyProtocol  

cadPolicyDistListOutRoutingProcess 6.4.1.4998.1.1.35.1.12.1.4
Destination VRF ID under which distribute list is configured.
OBJECT-TYPE    
  Integer32 1..2147483647  

cadPolicyDistListOutAutonomousSystemNum 6.4.1.4998.1.1.35.1.12.1.5
Autonomous system number of BGP to which routes need to be redistributed. If destination protocol is BGP appropriate AS number needs to be filled for this object. Otherwise set a value of 1 for this object.
OBJECT-TYPE    
  Integer32 -1..2147483647  

cadPolicyDistListOutAccessListNum 6.4.1.4998.1.1.35.1.12.1.6
The configured distribute out list refers to the access list specified. The access list number must be in the range of 1 - 99
OBJECT-TYPE    
  Integer32 1..99  

cadPolicyDistListOutAccessListName 6.4.1.4998.1.1.35.1.12.1.7
Name of the access list referred by distribute list. The access list name must be less than 32 characters
OBJECT-TYPE    
  OCTET STRING Size(1..32)  

cadPolicyDistListOutStatus 6.4.1.4998.1.1.35.1.12.1.8
The row status variable, used according to row installation and removal conventions. Once access list specified default row status is UP.
OBJECT-TYPE    
  RowStatus  

cadPolicyDistListOutIfIndex 6.4.1.4998.1.1.35.1.12.1.9
Interface for which distribute list is applied. The value will be 1 if the distribute list is applied to all interfaces.
OBJECT-TYPE    
  InterfaceIndex  

cadDistListOutTable 6.4.1.4998.1.1.35.1.13
Distribute List Out Table
OBJECT-TYPE    
  SEQUENCE OF  
    CadDistListOutEntry

cadDistListOutEntry 6.4.1.4998.1.1.35.1.13.1
A row in Distribute List Out table
OBJECT-TYPE    
  CadDistListOutEntry  

cadDistListOutVrIndex 6.4.1.4998.1.1.35.1.13.1.1
virtual router index
OBJECT-TYPE    
  Integer32 1..99  

cadDistListOutDestProtocol 6.4.1.4998.1.1.35.1.13.1.2
Destination protocol for which distribute list is applied.
OBJECT-TYPE    
  InfoSourceDest  

cadDistListOutSrcProtocol 6.4.1.4998.1.1.35.1.13.1.3
Source protocol for which distribute list is applied.
OBJECT-TYPE    
  InfoSourceDest  

cadDistListOutAccessListNum 6.4.1.4998.1.1.35.1.13.1.4
Access List Number
OBJECT-TYPE    
  Integer32 0..999  

cadDistListOutStatus 6.4.1.4998.1.1.35.1.13.1.5
The row status variable, used according to row installation and removal conventions. Once access list specified default row status is active.
OBJECT-TYPE    
  RowStatus  

cadDistListOutAccessListName 6.4.1.4998.1.1.35.1.13.1.6
Access List Name
OBJECT-TYPE    
  SnmpAdminString Size(0..32)  

cadAclNameTable 6.4.1.4998.1.1.35.1.14
This table maps names to ACL entries. Each row associates a name with the indexed ACL.
OBJECT-TYPE    
  SEQUENCE OF  
    CadAclNameEntry

cadAclNameEntry 6.4.1.4998.1.1.35.1.14.1
A conceptual row containing name information about an ACL.
OBJECT-TYPE    
  CadAclNameEntry  

cadNameAclName 6.4.1.4998.1.1.35.1.14.1.1
The name of the access control list.
OBJECT-TYPE    
  SnmpAdminString Size(1..32)  

cadNameAclNumber 6.4.1.4998.1.1.35.1.14.1.2
Extended ACL number. Extended ACLs are in the range 100-199. Standard ACLs are in the range 1-99.
OBJECT-TYPE    
  Integer32 1..399  

cadNameAclStatus 6.4.1.4998.1.1.35.1.14.1.3
RowStatus used to add and remove names for ACLs. When an ACL is removed, the associated name is also removed.
OBJECT-TYPE    
  RowStatus  

cadAclControl 6.4.1.4998.1.1.35.1.15
OBJECT IDENTIFIER    

cadAclOrderAcl 6.4.1.4998.1.1.35.1.15.1
This variable always returns false(2) upon reading. When set to true(1), the ACL identified in cadAclOrderAclIndex is renumbered with interval cadAclOrderAclInterval.
OBJECT-TYPE    
  TruthValue  

cadAclOrderAclIndex 6.4.1.4998.1.1.35.1.15.2
This variable identifies the ACL that should be renumbered.
OBJECT-TYPE    
  INTEGER 1..399  

cadAclOrderAclInterval 6.4.1.4998.1.1.35.1.15.3
This variable specifies the numbering interval used between each ACE when reordering an ACL.
OBJECT-TYPE    
  INTEGER 1..1000  

cadAclOrderAclStart 6.4.1.4998.1.1.35.1.15.4
This variable specifies the index that ACL reordering will use as the base for the first ACE.
OBJECT-TYPE    
  INTEGER 1..1000  

cadAclClearIpv4AclCounts 6.4.1.4998.1.1.35.1.15.5
This variable specifies the access list number for which all IPv4 per-entry counts will be cleared. This number may correspond to an individual access list (1..199). Setting to '0' will cause the per-entry counts to be cleared for ALL IPv4 configured access lists. This variable always returns '0' upon reading
OBJECT-TYPE    
  Integer32 0..199  

cadAclClearIpv6AclCounts 6.4.1.4998.1.1.35.1.15.6
This variable specifies the access list number for which all IPv6 per-entry counts will be cleared. This number may correspond to an individual access list (200..399). Setting to '0' will cause the per-entry counts to be cleared for ALL IPv6 configured access lists. This variable always returns '0' upon reading
OBJECT-TYPE    
  Integer32 0 | 200..399  

cadPolicyAclExtTable 6.4.1.4998.1.1.35.1.16
The cadPolicyAclExtTable augments the cadPolicyAclTable with a count for total number of times the access list entry has been matched by all referencing applications.
OBJECT-TYPE    
  SEQUENCE OF  
    CadPolicyAclExtEntry

cadPolicyAclExtEntry 6.4.1.4998.1.1.35.1.16.1
Information about the policy access list entry.
OBJECT-TYPE    
  CadPolicyAclExtEntry  

cadAclEntryCount 6.4.1.4998.1.1.35.1.16.1.1
Total number of times the access list entry has been matched by all referencing applications.
OBJECT-TYPE    
  Counter64  

cadPolicyRouting 6.4.1.4998.1.1.35.1.30
OBJECT IDENTIFIER    

cadRouteMapTagTable 6.4.1.4998.1.1.35.1.30.1
This table maps policy route map names to route map entries. Each row associates a name with the indexed policy route map.
OBJECT-TYPE    
  SEQUENCE OF  
    CadRouteMapTagEntry

cadRouteMapTagEntry 6.4.1.4998.1.1.35.1.30.1.1
A conceptual row containing name information for a policy route map.
OBJECT-TYPE    
  CadRouteMapTagEntry  

cadRouteMapTagName 6.4.1.4998.1.1.35.1.30.1.1.1
Name to used for this policy route map
OBJECT-TYPE    
  SnmpAdminString Size(1..64)  

cadRouteMapTagId 6.4.1.4998.1.1.35.1.30.1.1.2
Id used to associate entries in the policy route map table to this name.
OBJECT-TYPE    
  Integer32 1..64  

cadRouteMapTagRowStatus 6.4.1.4998.1.1.35.1.30.1.1.3
The row status variable used according to row installation and removal convention. In our case, we have simplified this to the usage of only the following states - active, createAndGo, and destroy. Other three states notInService, notReady and createAndWait are not permitted.
OBJECT-TYPE    
  RowStatus  

cadRouteMapTable 6.4.1.4998.1.1.35.1.30.2
This table contains policy route map data where each row contains information about the ACL being used and what set operations should be applied to the IP packet on a match.
OBJECT-TYPE    
  SEQUENCE OF  
    CadRouteMapEntry

cadRouteMapEntry 6.4.1.4998.1.1.35.1.30.2.1
A conceptual row containing information for a policy route map entry.
OBJECT-TYPE    
  CadRouteMapEntry  

cadRouteMapId 6.4.1.4998.1.1.35.1.30.2.1.1
Id used to associate entries in the policy route map table.
OBJECT-TYPE    
  Integer32 1..64  

cadRouteMapSeqNum 6.4.1.4998.1.1.35.1.30.2.1.2
Sequence number used to order the match statements.
OBJECT-TYPE    
  Integer32 1..2147483647  

cadRouteMapMatchType 6.4.1.4998.1.1.35.1.30.2.1.3
Type of match to used for this entry. Permit matches on the provided ACL and then applies the defined set operations before destination routing. Deny matches on the provided ACL and then directly routes to the destination without applying any of the set critera to the packet.
OBJECT-TYPE    
  INTEGER permit(1), deny(2)  

cadRouteMapMatchAcl 6.4.1.4998.1.1.35.1.30.2.1.4
ACL used to match the incoming packet. Since IPv4 is the only supported address type, the ACL number must be an extended or standard ACL. A value 0 implies that no ACL is used and all packets will match this entry.
OBJECT-TYPE    
  Integer32 0..199  

cadRouteMapSetIpPrec 6.4.1.4998.1.1.35.1.30.2.1.5
Indicates whether the IP Precedence should be changed on the packet if it matches the ACL and this is a permit type of match.
OBJECT-TYPE    
  TruthValue  

cadRouteMapIpPrec 6.4.1.4998.1.1.35.1.30.2.1.6
The IP precedence value that should be used to replace the existing IP precedence of the matching packet.
OBJECT-TYPE    
  INTEGER routine(0), priority(1), immediate(2), flash(3), flash-override(4), critical(5), internet(6), network(7)  

cadRouteMapSetIpTos 6.4.1.4998.1.1.35.1.30.2.1.7
Indicates whether the IP TOS should be changed on the packet if it matches the ACL and this is a permit type of match.
OBJECT-TYPE    
  TruthValue  

cadRouteMapIpTos 6.4.1.4998.1.1.35.1.30.2.1.8
The IP TOS value that should be used to replace the existing IP TOS of the matching packet.
OBJECT-TYPE    
  INTEGER normal(0), min-monetary-cost(1), max-reliability(2), max-throughput(4), min-delay(8)  

cadRouteMapSetNextHop 6.4.1.4998.1.1.35.1.30.2.1.9
Indicates whether the next hop setting should be used to specify the adjacent next hop router when forwarding the matching packet.
OBJECT-TYPE    
  TruthValue  

cadRouteMapNextHopAddrType 6.4.1.4998.1.1.35.1.30.2.1.10
The address type of the next hop and backup next hop addresses. Currently IPv4 is the only supported address type.
OBJECT-TYPE    
  InetAddressType  

cadRouteMapNextHop 6.4.1.4998.1.1.35.1.30.2.1.11
The address of the adjacent next hop router to use in forwading the matching packet. The next hop router address must be the address of an ajacent router, and the routing table (VRF?) is used to verify that the address can be directly reached. Only IPv4 addresses are currently supported.
OBJECT-TYPE    
  InetAddress  

cadRouteMapSetBackupNextHop 6.4.1.4998.1.1.35.1.30.2.1.12
Indicates whether the backup next hop setting should be used to specify the adjacent next hop router when forwarding the matching packet. This only would be done if the primary next hop was not set or was unreachable.
OBJECT-TYPE    
  TruthValue  

cadRouteMapBackupNextHop 6.4.1.4998.1.1.35.1.30.2.1.13
The address type of a second next hop, that can be used only if the primary next hop address can not be reached. Only Ipv4 addresses are currently supported.
OBJECT-TYPE    
  InetAddress  

cadRouteMapSetNullInterface 6.4.1.4998.1.1.35.1.30.2.1.14
If set to true and the packet matches the ACL, it will be dropped.
OBJECT-TYPE    
  TruthValue  

cadRouteMapRowStatus 6.4.1.4998.1.1.35.1.30.2.1.15
The row status variable used according to row installation and removal convention. In our case, we have simplified this to the usage of only the following states - active, createAndGo, and destroy. Other three states notInService, notReady and createAndWait are not permitted.
OBJECT-TYPE    
  RowStatus  

cadRouteMapSetIpDscp 6.4.1.4998.1.1.35.1.30.2.1.16
Indicates whether the IP DSCP should be changed on the packet if it matches the ACL and this is a permit type of match.
OBJECT-TYPE    
  TruthValue  

cadRouteMapIpDscp 6.4.1.4998.1.1.35.1.30.2.1.17
The IP DSCP value that should be used to replace the existing IP DSCP of the matching packet.
OBJECT-TYPE    
  INTEGER 0..63  

cadRouteMapSetRecursiveNextHop 6.4.1.4998.1.1.35.1.30.2.1.18
Indicates whether the recursive next hop setting should be used to specify the next hop for the remote router when forwarding the matching packet.
OBJECT-TYPE    
  TruthValue  

cadRouteMapRecursiveNextHop 6.4.1.4998.1.1.35.1.30.2.1.19
The address type of a remote router next hop, that is used to perform a recursive route lookup. Only Ipv4 addresses are currently supported.
OBJECT-TYPE    
  InetAddress  

cadRouteMapStatsTable 6.4.1.4998.1.1.35.1.30.3
This table contains policy route map counts where each row contains information about the number of packets that match the specified ACL and were successfully changed with the defined set operations, as well as those that matched the ACL but failed the set operations.
OBJECT-TYPE    
  SEQUENCE OF  
    CadRouteMapStatsEntry

cadRouteMapStatsEntry 6.4.1.4998.1.1.35.1.30.3.1
A conceptual row containing counts information for a policy route map entry.
OBJECT-TYPE    
  CadRouteMapStatsEntry  

cadRouteMapPktMatched 6.4.1.4998.1.1.35.1.30.3.1.1
The number of packets that match the ACL defined in the route map entry and where the action was also successful. For matches of type deny, the packet is routed by destination, and for packets of type match, the packet is successfully modified and sent.
OBJECT-TYPE    
  Counter32  

cadRouteMapByteMatched 6.4.1.4998.1.1.35.1.30.3.1.2
The number of bytes that match the ACL defined in the route map entry and where the action was also successful. For matches of type deny, the packet is routed by destination, and for packets of type match, the packet is successfully modified and sent.
OBJECT-TYPE    
  Counter64  

cadRouteMapPktFailed 6.4.1.4998.1.1.35.1.30.3.1.3
The number of packets that match the ACL defined in the route map entry and where the action failed. For route map entries of type match, the set operation failed.
OBJECT-TYPE    
  Counter32  

cadRouteMapByteFailed 6.4.1.4998.1.1.35.1.30.3.1.4
The number of packets that match the ACL defined in the route map entry and where the action failed. For route map entries of type match, the set operation failed.
OBJECT-TYPE    
  Counter64  

cadRouteMapClearStats 6.4.1.4998.1.1.35.1.30.4
Setting this value will reset all the byte and packet counts for a route map. A value of 0 indicates no reset is performed.
OBJECT-TYPE    
  Integer32 0..64  

cadLocalPolicyRouteMap 6.4.1.4998.1.1.35.1.30.5
This value contains the mapId of the policy route map to be used for local policy based routing. A value of 0 indicates no local policy routing is performed.
OBJECT-TYPE    
  Integer32 0..64