C-PRODUCT-BASE-MIB

File: C-PRODUCT-BASE-MIB.mib (51363 bytes)

Imported modules

C-PRODUCT-GROUP-MIB RFC1155-SMI RFC1213-MIB
RFC-1212

Imported symbols

sys shelf card
port circuit fault
IpAddress DisplayString PhysAddress
OBJECT-TYPE

Defined Types

TimeAndDate  
STRING Size(6..6)    

CardType  
INTEGER none(1), mcpu(2), ds3(3), ether(4), ctx(5), oc3(6), backplane(7), hssi(8), cbr-dsx-4(9), cbr-e1-4(11), cbr-dsx-8(12), cbr-e1-8(14), unknown(15), v-35-qsim(16), rs-422-qsim(17), hsim(18), e3(19), ima-dsx-8(20), ima-csu-8(21), ima-e1-8(22), ima-dsx-4(23), ima-csu-4(24), ima-e1-4(25), fam-csu-8(26), ctx-plus(27), fam-dsx-8(28), fam-e1-8(29), mojave-backplane(30), ima-4-9300(31), cbr-dsx-3-v35(32), cbr-csu-3-v35(33), cbr-e1-3-v35(34), cbr-dsx-4-9300(35), cbr-csu-4-9300(36), cbr-e1-4-9300(37), ctx-9300(38)    

AdminStatus  
INTEGER out-of-service(1), in-service(2)    

PortOperStatus  
INTEGER out-of-service(1), in-service(2), no-response(3), coming-up(4), coming-down(5), status-failed(6)    

CardOperStatus  
INTEGER out-of-service(1), in-service(2), failed(6)    

CardShelfState  
INTEGER empty(1), missing(2), match(3), mismatch(4), invalid(5), hwrev-mismatch(6)    

VcpPacketDiscard  
INTEGER pkt-no(1), pkt-yes(2)    

AlarmType  
INTEGER los(1), oof(2), ais(3), idle(4), ferf(5), lcd(6), vp-ais(7), vc-ais(8), upload-image-missing(9), card-reconf-ok(10), unknown-db-card-type(11), card-reconf-fail(12), card-mismatch(13), new-card-conf-ok(14), card-conf-fail(15), unknown-card-type(16), card-removed(17), download-fail(18), ps1-missing(19), ps2-missing(20), ps1-fail(21), ps2-fail(22), relay-fuse-fail(23), comm-fail(24), fan1-fail(25), fan2-fail(26), fan3-fail(27), fan4-fail(28), feac-lpbk(29), ntwk-line-lpbk(30), card-lpbk(31), cell-lpbk(32), card-missing(33), card-inited(34), cellbus-parity-fail(35), rx-fifo-overflow(36), tx-fifo-overflow(37), lp-cellbus-congest(38), mp-cellbus-congest(39), hp-cellbus-congest(40), prom-checksum-fail(43), sram-0-fail(44), sram-1-fail(45), sar-sram-fail(46), hdlc-sram-fail(47), mailbox-sram-fail(48), cellbus-xilink-fail(49), prt01-xlnk-fail(50), prt23-xlnk-fail(51), prt45-xlnk-fail(52), prt67-xlnk-fail(53), sar-xlnk-fail(54), port-lpbk-pseudo-fail(55), e1-slot16-ais(56), e1-loss-cas-multifrm(57), fe-e1-loss-cas(58), port-yellow(61), port-ais(62), vc-rdi(64), local-card-lpbk(65), intern-refclk-fail(66), bits-refclk-fail(67), cbr-refclk-fail(68), plcp-refclk-fail(69), loss-of-clock(70), remote-lpbk(71), oc3-refclk-missing(73), power-up(75), loss-cell-del(77), loss-ima-frame(78), loss-diff-sync(79), dup-id(80), bad-ima-id(81), bad-ima-M-value(82), dup-link-id(83), dup-offset(84), test-pattern-fail(85), bad-link-id(86), bad-offset(87), fe-no-links(88), fe-bad-M(89), fe-group-error(90), fe-los-of-signal(91), fe-out-of-frame(92), fe-loss-cell-del(93), fe-loss-of-frame(94), fe-loss-diff-sync(95), fe-misconnected(96), alarm-cleared(102), history-overflow(103), afa-link-removal(104), lmi-link-down(105), link-delay(106), group-no-link(107), group-degraded(108), group-sync-failed(109), sar-init-failure(110)    

VcpLinkType  
INTEGER vc-invalid(1), vc-regular(2), vc-multicast(3), vc-management(4), vc-leaf(5)    

VcFamilyCardType  
INTEGER cardFamNone(1), cardFamMCPU(2), cardFamCTX(3), cardFamOC3(4), cardFamDS3(5), cardFamE3(6), cardFamQSIM(7), cardFamFAM(8), cardFamENET(9), cardFamHSSI(10), cardFamCBR(11), cardFamIMA(12), cardFamBackplane(13)    

SysIpConfigTrapClientEntry  
SEQUENCE    
  sysIpConfigTrapClientIndex INTEGER
  sysIpConfigTrapClientIpAddress IpAddress
  sysIpConfigTrapClientSubnetMask IpAddress
  sysIpConfigTrapClientPortNumber INTEGER

SysRs232Entry  
SEQUENCE    
  sysRs232Port INTEGER
  sysRs232BaudRate INTEGER
  sysRs232Parity INTEGER
  sysRs232DataBits INTEGER
  sysRs232StopBits INTEGER

ShelfPowerSupplyEntry  
SEQUENCE    
  shelfPowerSupplySlot INTEGER
  shelfPowerSupplyAdminStatus AdminStatus
  shelfPowerSupplyOperStatus INTEGER

CardBaseEntry  
SEQUENCE    
  cardSlot INTEGER
  cardTypeDb CardType
  cardTypeHw CardType
  cardAdminStatus AdminStatus
  cardOperStatus CardOperStatus
  cardSerialNumber STRING
  cardRevision STRING
  cardPartNumber DisplayString
  cardReset INTEGER
  cardShelfState CardShelfState

PortBaseEntry  
SEQUENCE    
  portSlot INTEGER
  portNumber INTEGER
  portAdminStatus AdminStatus
  portOperStatus PortOperStatus
  portIfIndex INTEGER

VcpBaseEntry  
SEQUENCE    
  vcpSideAId INTEGER
  vcpSideBId INTEGER
  vcpLinkType VcpLinkType
  vcpDescription DisplayString
  vcpAdminStatus AdminStatus
  vcpRowStatus INTEGER

VcpSideEntry  
SEQUENCE    
  vcpSideId INTEGER
  vcpSideSlot INTEGER
  vcpSidePort INTEGER
  vcpSideTransmitVpi INTEGER
  vcpSideTransmitVci INTEGER
  vcpSideReceiveVpi INTEGER
  vcpSideReceiveVci INTEGER
  vcpSidePriority INTEGER
  vcpSidePacketDiscard VcpPacketDiscard

VcpMappingSideEntry  
SEQUENCE    
  vcpMappingSideSlot INTEGER
  vcpMappingSidePort INTEGER
  vcpMappingSideAId INTEGER
  vcpMappingSideBId INTEGER
  vcpMappingCardType CardType
  vcpMappingFamCardType VcFamilyCardType
  vcpMappingOtherCardType CardType
  vcpMappingOtherFamCardType VcFamilyCardType

FaultCurrentAlarmEntry  
SEQUENCE    
  faultCurrentAlarmTag INTEGER
  faultCurrentAlarmAlarmType AlarmType
  faultCurrentAlarmSeverity INTEGER
  faultCurrentAlarmCardType CardType
  faultCurrentAlarmCardNumber INTEGER
  faultCurrentAlarmPortNumber INTEGER
  faultCurrentAlarmSetTime TimeAndDate
  faultCurrentAlarmDescription DisplayString

FaultHistoryAlarmEntry  
SEQUENCE    
  faultHistoryAlarmTag INTEGER
  faultHistoryAlarmAlarmType AlarmType
  faultHistoryAlarmSeverity INTEGER
  faultHistoryAlarmCardType CardType
  faultHistoryAlarmCardNumber INTEGER
  faultHistoryAlarmPortNumber INTEGER
  faultHistoryAlarmSetTime TimeAndDate
  faultHistoryAlarmDescription DisplayString
  faultHistoryAlarmClearTime TimeAndDate

Defined Values

sysGenInfo 1.3.6.1.4.1.43.1.12.1.1.1.1
OBJECT IDENTIFIER    

sysGenInfoShelfName 1.3.6.1.4.1.43.1.12.1.1.1.1.1
Name of the managed node.
OBJECT-TYPE    
  DisplayString Size(0..16)  

sysGenInfoCustomerName 1.3.6.1.4.1.43.1.12.1.1.1.1.2
Name of the organization that uses the managed node.
OBJECT-TYPE    
  DisplayString Size(0..32)  

sysGenInfoPhoneNumber 1.3.6.1.4.1.43.1.12.1.1.1.1.3
Phone number of the organization that uses the managed node.
OBJECT-TYPE    
  DisplayString Size(0..32)  

sysGenInfoMaintenanceContact 1.3.6.1.4.1.43.1.12.1.1.1.1.4
Maintenance contact of the managed node.
OBJECT-TYPE    
  DisplayString Size(0..32)  

sysGenInfoLocation 1.3.6.1.4.1.43.1.12.1.1.1.1.5
Location of the managed node.
OBJECT-TYPE    
  DisplayString Size(0..32)  

sysGenInfoAutoLogoutTime 1.3.6.1.4.1.43.1.12.1.1.1.1.6
The time a TELNET or VT-100 terminal user can maintain a session with the managed node without any keyboard action. Unit: minute
OBJECT-TYPE    
  INTEGER 1..99  

sysGenInfoPassword 1.3.6.1.4.1.43.1.12.1.1.1.1.7
Password required to access the managed node using VT-100 terminal or TELNET. A get request always returns a NULL string.
OBJECT-TYPE    
  STRING Size(0..16)  

sysGenCurrentCodeRelease 1.3.6.1.4.1.43.1.12.1.1.1.1.8
Firmware revision of the current code running in the managed node.
OBJECT-TYPE    
  DisplayString  

sysTimeAndDate 1.3.6.1.4.1.43.1.12.1.1.1.2
Time and date maintained in the managed node.
OBJECT-TYPE    
  TimeAndDate  

sysIpConfig 1.3.6.1.4.1.43.1.12.1.1.1.3
OBJECT IDENTIFIER    

sysIpConfigLocalHost 1.3.6.1.4.1.43.1.12.1.1.1.3.1
OBJECT IDENTIFIER    

sysIpConfigLocalHostCommunityName 1.3.6.1.4.1.43.1.12.1.1.1.3.1.1
Community name of the managed node. A get request always returns a NULL string.
OBJECT-TYPE    
  DisplayString Size(0..64)  

sysIpConfigLocalHostIpAddress 1.3.6.1.4.1.43.1.12.1.1.1.3.1.2
Local host's Ethernet IP address.
OBJECT-TYPE    
  IpAddress  

sysIpConfigLocalHostSubnetMask 1.3.6.1.4.1.43.1.12.1.1.1.3.1.3
Local host's Ethernet IP subnet mask.
OBJECT-TYPE    
  IpAddress  

sysIpConfigLocalHostMacAddress 1.3.6.1.4.1.43.1.12.1.1.1.3.1.4
Local host's Ethernet MAC-layer address.
OBJECT-TYPE    
  PhysAddress  

sysIpConfigTrapGateway 1.3.6.1.4.1.43.1.12.1.1.1.3.2
OBJECT IDENTIFIER    

sysIpConfigTrapGatewayIpAddress 1.3.6.1.4.1.43.1.12.1.1.1.3.2.1
Trap gateway's IP address.
OBJECT-TYPE    
  IpAddress  

sysIpConfigTrapGatewaySubnetMask 1.3.6.1.4.1.43.1.12.1.1.1.3.2.2
Trap gateway's IP subnet mask.
OBJECT-TYPE    
  IpAddress  

sysIpConfigTrapClientTable 1.3.6.1.4.1.43.1.12.1.1.1.3.3
Trap client table has 4 entries
OBJECT-TYPE    
  SEQUENCE OF  
    SysIpConfigTrapClientEntry

sysIpConfigTrapClientEntry 1.3.6.1.4.1.43.1.12.1.1.1.3.3.1
Each entry contains IP address and port number of an SNMP manager which receives traps from the managed node.
OBJECT-TYPE    
  SysIpConfigTrapClientEntry  

sysIpConfigTrapClientIndex 1.3.6.1.4.1.43.1.12.1.1.1.3.3.1.1
Tok_String
OBJECT-TYPE    
  INTEGER 1..4  

sysIpConfigTrapClientIpAddress 1.3.6.1.4.1.43.1.12.1.1.1.3.3.1.2
Trap client's IP address.
OBJECT-TYPE    
  IpAddress  

sysIpConfigTrapClientSubnetMask 1.3.6.1.4.1.43.1.12.1.1.1.3.3.1.3
Trap client's IP subnet mask.
OBJECT-TYPE    
  IpAddress  

sysIpConfigTrapClientPortNumber 1.3.6.1.4.1.43.1.12.1.1.1.3.3.1.4
Trap client's port number.
OBJECT-TYPE    
  INTEGER  

sysRs232Table 1.3.6.1.4.1.43.1.12.1.1.1.4
This table contains 2 rows. The first row shows the physical configuration of the port connected to a VT100 termianl. The second row is used to configure the port which supports SLIP. Access to the first row is read-only and access to the second row is read-write.
OBJECT-TYPE    
  SEQUENCE OF  
    SysRs232Entry

sysRs232Entry 1.3.6.1.4.1.43.1.12.1.1.1.4.1
Each entry contains the attributes of a serial port.
OBJECT-TYPE    
  SysRs232Entry  

sysRs232Port 1.3.6.1.4.1.43.1.12.1.1.1.4.1.1
The managed node has 2 serial ports: port 1 and port 2.
OBJECT-TYPE    
  INTEGER port-1(1), port-2(2)  

sysRs232BaudRate 1.3.6.1.4.1.43.1.12.1.1.1.4.1.2
Baud rate. The instance of this object in port-1 is read-only.
OBJECT-TYPE    
  INTEGER br-300(1), br-1200(2), br-2400(3), br-4800(4), br-9600(5), br-19200(6), br-38400(7)  

sysRs232Parity 1.3.6.1.4.1.43.1.12.1.1.1.4.1.3
Parity. The instance of this object in port-1 is read-only.
OBJECT-TYPE    
  INTEGER none(1), even(2), odd(3)  

sysRs232DataBits 1.3.6.1.4.1.43.1.12.1.1.1.4.1.4
Number of data bits. The instance of this object in port-1 is read-only.
OBJECT-TYPE    
  INTEGER db-7(1), db-8(2)  

sysRs232StopBits 1.3.6.1.4.1.43.1.12.1.1.1.4.1.5
Number of stop bits. The instance of this object in port-1 is read-only.
OBJECT-TYPE    
  INTEGER sb-1(1), sb-2(2)  

sysRefClock 1.3.6.1.4.1.43.1.12.1.1.1.5
System reference clock maintained in the managed node.
OBJECT-TYPE    
  INTEGER no-clock(1), internal-default(2), internal(3), bits(4), slot-3(5), slot-4(6), slot-5(7), slot-6(8), slot-7(9), slot-8(10), slot-9(11)  

sysProductType 1.3.6.1.4.1.43.1.12.1.1.1.6
System Product Type contain type of product.
OBJECT-TYPE    
  INTEGER no-product(1), ab9600(2), ab9300(3), ab9100(4), mojave(5)  

shelfSerialNumber 1.3.6.1.4.1.43.1.12.1.1.2.1
Serial number of the shelf.
OBJECT-TYPE    
  STRING Size(10..10)  

shelfRevision 1.3.6.1.4.1.43.1.12.1.1.2.2
Hardware revision number of the shelf.
OBJECT-TYPE    
  STRING Size(1..1)  

shelfPowerSupplyTable 1.3.6.1.4.1.43.1.12.1.1.2.3
The power supply table in the shelf.
OBJECT-TYPE    
  SEQUENCE OF  
    ShelfPowerSupplyEntry

shelfPowerSupplyEntry 1.3.6.1.4.1.43.1.12.1.1.2.3.1
Information of the power supply in the shelf.
OBJECT-TYPE    
  ShelfPowerSupplyEntry  

shelfPowerSupplySlot 1.3.6.1.4.1.43.1.12.1.1.2.3.1.1
Slot number of the power supply.
OBJECT-TYPE    
  INTEGER slot-1(1), slot-2(2)  

shelfPowerSupplyAdminStatus 1.3.6.1.4.1.43.1.12.1.1.2.3.1.2
Administrative status.
OBJECT-TYPE    
  AdminStatus  

shelfPowerSupplyOperStatus 1.3.6.1.4.1.43.1.12.1.1.2.3.1.3
Operational status for Power Supply. In AB9300/AB9100, it doesn't support any setting value.
OBJECT-TYPE    
  INTEGER out-of-service(1), in-service(2), missing(3)  

shelfPartNumber 1.3.6.1.4.1.43.1.12.1.1.2.4
Part number of the shelf.
OBJECT-TYPE    
  STRING Size(1..1)  

cardBaseTable 1.3.6.1.4.1.43.1.12.1.1.3.1
A 6 entry card table in the shelf.
OBJECT-TYPE    
  SEQUENCE OF  
    CardBaseEntry

cardBaseEntry 1.3.6.1.4.1.43.1.12.1.1.3.1.1
Each card entry contains objects that refer to the card in that entry.
OBJECT-TYPE    
  CardBaseEntry  

cardSlot 1.3.6.1.4.1.43.1.12.1.1.3.1.1.1
Slot number of the card in the shelf. The assignment of the card slots is as follows: slot 1 : management cpu, slot 2 : ctx card, slot 3 : one of the trunk cards (e.g. ds3/oc3/e3/hssi), slot 4-6: one of the port cards (e.g. ether/cbr/qsim).
OBJECT-TYPE    
  INTEGER 1..6  

cardTypeDb 1.3.6.1.4.1.43.1.12.1.1.3.1.1.2
The configured card type in the slot. It may differ from the actual card type (cardTypeHw) in the corresponding slot. A set request will be accepted only when one of the following is true: 1. the value of cardTypeHw in this slot is none, or 2. the new value of cardTypeDb is the same as the corresponding cardTypeHw.
OBJECT-TYPE    
  CardType  

cardTypeHw 1.3.6.1.4.1.43.1.12.1.1.3.1.1.3
The actual card type in the slot.
OBJECT-TYPE    
  CardType  

cardAdminStatus 1.3.6.1.4.1.43.1.12.1.1.3.1.1.4
Administrative status of the card. An error is returned if this slot has been selected as the system reference clock and an attempt is made to change this object to out-of-service. This object does not apply to management cpu and ctx card.
OBJECT-TYPE    
  AdminStatus  

cardOperStatus 1.3.6.1.4.1.43.1.12.1.1.3.1.1.5
Operational status of the card.
OBJECT-TYPE    
  CardOperStatus  

cardSerialNumber 1.3.6.1.4.1.43.1.12.1.1.3.1.1.6
Serial number of the card.
OBJECT-TYPE    
  STRING Size(10..10)  

cardRevision 1.3.6.1.4.1.43.1.12.1.1.3.1.1.7
Hardware revision number of the card.
OBJECT-TYPE    
  STRING Size(1..1)  

cardPartNumber 1.3.6.1.4.1.43.1.12.1.1.3.1.1.8
Part number of the card.
OBJECT-TYPE    
  DisplayString  

cardReset 1.3.6.1.4.1.43.1.12.1.1.3.1.1.9
This is the command to reset the card at the specified slot number. A read request always returns 0. Warning: Reseting card will temporarily disrupt traffic on the specified slot number.
OBJECT-TYPE    
  INTEGER reset(1)  

cardShelfState 1.3.6.1.4.1.43.1.12.1.1.3.1.1.10
Operational shelf state of the card.
OBJECT-TYPE    
  CardShelfState  

portBaseTable 1.3.6.1.4.1.43.1.12.1.1.4.1
The port information table.
OBJECT-TYPE    
  SEQUENCE OF  
    PortBaseEntry

portBaseEntry 1.3.6.1.4.1.43.1.12.1.1.4.1.1
Each port entry contains objects that refer to the port in that entry.
OBJECT-TYPE    
  PortBaseEntry  

portSlot 1.3.6.1.4.1.43.1.12.1.1.4.1.1.1
Slot Number. This table does not have objects for management cpu (slot #1) and ctx card (slot #2).
OBJECT-TYPE    
  INTEGER 3..6  

portNumber 1.3.6.1.4.1.43.1.12.1.1.4.1.1.2
Port number. The number of ports in each card depends on the type of card in that slot. Following is a list of cards and the port range of that cards: card type port range ----------- ---------- ds3 1..1 ether 1..2 oc3 1..1 hssi 1..1 cbr-dsx-4 1..4 cbr-e1-4 1..4 cbr-dsx-8 1..8 cbr-e1-8 1..8 v-35-qsim 1..4 rs-422-qsim 1..4 hssi-qsim 1..1 e3 1..1
OBJECT-TYPE    
  INTEGER  

portAdminStatus 1.3.6.1.4.1.43.1.12.1.1.4.1.1.3
Administrative status of the port. An error is returned if this port has been selected as the system reference clock and an attempt is made to change this object to out-of-service.
OBJECT-TYPE    
  AdminStatus  

portOperStatus 1.3.6.1.4.1.43.1.12.1.1.4.1.1.4
Operational status of the port.
OBJECT-TYPE    
  PortOperStatus  

portIfIndex 1.3.6.1.4.1.43.1.12.1.1.4.1.1.5
Currently this object applies to the interface ports in port cards ONLY. It is pre-assigned as following: slot range 3 1..8 4 9..16 5 17..24 6 25..32 7 33..40 8 41..48 9 49..57
OBJECT-TYPE    
  INTEGER 1..57  

vcpNextAvailGlobVcSideId 1.3.6.1.4.1.43.1.12.1.1.5.2
This unique value which identified the next available virtual circuit ID. It is allowed NMS manager to get the next available Virtual Circuit Id before created a new row into Virtual circuit Path Table.
OBJECT-TYPE    
  INTEGER 0..2147483647  

vcpBaseTable 1.3.6.1.4.1.43.1.12.1.1.5.3
The base virtual circuit table contains the common information for both sides of circuit.
OBJECT-TYPE    
  SEQUENCE OF  
    VcpBaseEntry

vcpBaseEntry 1.3.6.1.4.1.43.1.12.1.1.5.3.1
Information of the base virtual circuit.
OBJECT-TYPE    
  VcpBaseEntry  

vcpSideAId 1.3.6.1.4.1.43.1.12.1.1.5.3.1.1
A unique value which identifies the SideA of circuit.
OBJECT-TYPE    
  INTEGER 0..2147483647  

vcpSideBId 1.3.6.1.4.1.43.1.12.1.1.5.3.1.2
A unique value which identifies the SideB of circuit.
OBJECT-TYPE    
  INTEGER 0..2147483647  

vcpLinkType 1.3.6.1.4.1.43.1.12.1.1.5.3.1.3
Vc Circuit Type indicated whether this circuit is Regular, Multicast, Management, Unicast, leaf.
OBJECT-TYPE    
  VcpLinkType  

vcpDescription 1.3.6.1.4.1.43.1.12.1.1.5.3.1.4
Vc description of circuits.
OBJECT-TYPE    
  DisplayString Size(0..12)  

vcpAdminStatus 1.3.6.1.4.1.43.1.12.1.1.5.3.1.5
Vc administrative status.
OBJECT-TYPE    
  AdminStatus  

vcpRowStatus 1.3.6.1.4.1.43.1.12.1.1.5.3.1.6
This object indicates the action to be taken by a set request.
OBJECT-TYPE    
  INTEGER create(1), delete(2)  

vcpSideTable 1.3.6.1.4.1.43.1.12.1.1.5.4
The side table contains the Side A or Side B of circuit information.
OBJECT-TYPE    
  SEQUENCE OF  
    VcpSideEntry

vcpSideEntry 1.3.6.1.4.1.43.1.12.1.1.5.4.1
Information of the base virtual circuit.
OBJECT-TYPE    
  VcpSideEntry  

vcpSideId 1.3.6.1.4.1.43.1.12.1.1.5.4.1.1
unique number associated with virtual circuit.
OBJECT-TYPE    
  INTEGER 0..2147483647  

vcpSideSlot 1.3.6.1.4.1.43.1.12.1.1.5.4.1.2
Slot Number. This table does not have objects for ctx card (slot #2) and card (slot #3).
OBJECT-TYPE    
  INTEGER 1..9  

vcpSidePort 1.3.6.1.4.1.43.1.12.1.1.5.4.1.3
Port number. The number of ports in each card depends on the type of card in that slot. Following is a list of cards and the port range of that cards: card type port range ----------- ---------- mcpu 1..1 ds3 1..1 ether 1..2 oc3 1..1 hssi 1..1 cbr-dsx-4 1..4 cbr-csu-4 1..4 cbr-e1-4 1..4 cbr-dsx-8 1..8 cbr-csu-8 1..8 cbr-e1-8 1..8 v-35-qsim 1..4 rs-422-qsim 1..4 hssi-qsim 1..1 e3 1..1
OBJECT-TYPE    
  INTEGER  

vcpSideTransmitVpi 1.3.6.1.4.1.43.1.12.1.1.5.4.1.4
Port card transmit vpi.
OBJECT-TYPE    
  INTEGER 0..255  

vcpSideTransmitVci 1.3.6.1.4.1.43.1.12.1.1.5.4.1.5
Port card transmit vci.
OBJECT-TYPE    
  INTEGER 0..16383  

vcpSideReceiveVpi 1.3.6.1.4.1.43.1.12.1.1.5.4.1.6
Port card receive vpi. The value range 0..255 applies when VPI-only translation is requested. Otherwise, its range is 0..15. If the value of an instance of this object is > 15, the value of the corresponding instance of vcPortReceiveVci MUST be 0 (VPI-only translation).
OBJECT-TYPE    
  INTEGER 0..255  

vcpSideReceiveVci 1.3.6.1.4.1.43.1.12.1.1.5.4.1.7
Port card receive vci. If the value of this object is 0, VPI-only translation is requested.
OBJECT-TYPE    
  INTEGER 0..1023  

vcpSidePriority 1.3.6.1.4.1.43.1.12.1.1.5.4.1.8
Priority queue is to prioritize the circuit. The smallest number is the highest priority. The largest number is lowest priority.
OBJECT-TYPE    
  INTEGER 1..4  

vcpSidePacketDiscard 1.3.6.1.4.1.43.1.12.1.1.5.4.1.9
Packet Discard indicates whether this packet needs to drop off based on the threshold.
OBJECT-TYPE    
  VcpPacketDiscard  

vcpMappingSideTable 1.3.6.1.4.1.43.1.12.1.1.5.5
The Mapping side table contains circuit Side information.
OBJECT-TYPE    
  SEQUENCE OF  
    VcpMappingSideEntry

vcpMappingSideEntry 1.3.6.1.4.1.43.1.12.1.1.5.5.1
Information of the base virtual circuit.
OBJECT-TYPE    
  VcpMappingSideEntry  

vcpMappingSideSlot 1.3.6.1.4.1.43.1.12.1.1.5.5.1.1
Slot Number. This table does not have objects for ctx card (slot #2) and card (slot #3).
OBJECT-TYPE    
  INTEGER 1..9  

vcpMappingSidePort 1.3.6.1.4.1.43.1.12.1.1.5.5.1.2
Port number. The number of ports in each card depends on the type of card in that slot. Following is a list of cards and the port range of that cards: card type port range ----------- ---------- mcpu 1..1 ds3 1..1 ether 1..2 oc3 1..1 hssi 1..1 cbr-dsx-4 1..4 cbr-csu-4 1..4 cbr-e1-4 1..4 cbr-dsx-8 1..8 cbr-csu-8 1..8 cbr-e1-8 1..8 v-35-qsim 1..4 rs-422-qsim 1..4 hssi-qsim 1..1 e3 1..1
OBJECT-TYPE    
  INTEGER  

vcpMappingSideAId 1.3.6.1.4.1.43.1.12.1.1.5.5.1.3
SideA ID is a unique number associated with virtual circuit.
OBJECT-TYPE    
  INTEGER 0..2147483647  

vcpMappingSideBId 1.3.6.1.4.1.43.1.12.1.1.5.5.1.4
SideB ID is a unique number associated with virtual circuit.
OBJECT-TYPE    
  INTEGER 0..2147483647  

vcpMappingCardType 1.3.6.1.4.1.43.1.12.1.1.5.5.1.5
card Type associated with mySide of circuit.
OBJECT-TYPE    
  CardType  

vcpMappingFamCardType 1.3.6.1.4.1.43.1.12.1.1.5.5.1.6
Family Card Type associate with mySide of circuit.
OBJECT-TYPE    
  VcFamilyCardType  

vcpMappingOtherCardType 1.3.6.1.4.1.43.1.12.1.1.5.5.1.7
Other Side of Card Type associate with the circuit.
OBJECT-TYPE    
  CardType  

vcpMappingOtherFamCardType 1.3.6.1.4.1.43.1.12.1.1.5.5.1.8
Other Side of Family Card Type associate with the circuit.
OBJECT-TYPE    
  VcFamilyCardType  

faultClearCurrentAlarms 1.3.6.1.4.1.43.1.12.1.1.6.1
A set request clears all entries in the current alarm table. A get/get-next request returns 0.
OBJECT-TYPE    
  INTEGER  

faultClearHistoryAlarms 1.3.6.1.4.1.43.1.12.1.1.6.2
A set request clears all entries in the history alarm table. A get/get-next request returns 0.
OBJECT-TYPE    
  INTEGER  

faultCurrentAlarmTable 1.3.6.1.4.1.43.1.12.1.1.6.3
Current alarm table.
OBJECT-TYPE    
  SEQUENCE OF  
    FaultCurrentAlarmEntry

faultCurrentAlarmEntry 1.3.6.1.4.1.43.1.12.1.1.6.3.1
Each entry in the table contains the information of a currently active alarm.
OBJECT-TYPE    
  FaultCurrentAlarmEntry  

faultCurrentAlarmTag 1.3.6.1.4.1.43.1.12.1.1.6.3.1.1
The tag of the alarm in the current alarm table.
OBJECT-TYPE    
  INTEGER  

faultCurrentAlarmAlarmType 1.3.6.1.4.1.43.1.12.1.1.6.3.1.2
Alarm type.
OBJECT-TYPE    
  AlarmType  

faultCurrentAlarmSeverity 1.3.6.1.4.1.43.1.12.1.1.6.3.1.3
Alarm severity.
OBJECT-TYPE    
  INTEGER minor(2), major(3)  

faultCurrentAlarmCardType 1.3.6.1.4.1.43.1.12.1.1.6.3.1.4
Card type of the card which caused the alarm.
OBJECT-TYPE    
  CardType  

faultCurrentAlarmCardNumber 1.3.6.1.4.1.43.1.12.1.1.6.3.1.5
Slot number of the card which caused the alarm.
OBJECT-TYPE    
  INTEGER 1..6  

faultCurrentAlarmPortNumber 1.3.6.1.4.1.43.1.12.1.1.6.3.1.6
The port number of the card which caused the alarm.
OBJECT-TYPE    
  INTEGER 1..8  

faultCurrentAlarmSetTime 1.3.6.1.4.1.43.1.12.1.1.6.3.1.7
The time when the alarm was set.
OBJECT-TYPE    
  TimeAndDate  

faultCurrentAlarmDescription 1.3.6.1.4.1.43.1.12.1.1.6.3.1.8
A readable string which describes the alarm.
OBJECT-TYPE    
  DisplayString  

faultHistoryAlarmTable 1.3.6.1.4.1.43.1.12.1.1.6.4
History/Information alarm table.
OBJECT-TYPE    
  SEQUENCE OF  
    FaultHistoryAlarmEntry

faultHistoryAlarmEntry 1.3.6.1.4.1.43.1.12.1.1.6.4.1
Each entry in the history alarm table contains either a cleared alarm or an information alarm.
OBJECT-TYPE    
  FaultHistoryAlarmEntry  

faultHistoryAlarmTag 1.3.6.1.4.1.43.1.12.1.1.6.4.1.1
The tag of the alarm in the history alarm table.
OBJECT-TYPE    
  INTEGER  

faultHistoryAlarmAlarmType 1.3.6.1.4.1.43.1.12.1.1.6.4.1.2
Alarm type.
OBJECT-TYPE    
  AlarmType  

faultHistoryAlarmSeverity 1.3.6.1.4.1.43.1.12.1.1.6.4.1.3
Severity of the alarm.
OBJECT-TYPE    
  INTEGER info(1), minor(2), major(3)  

faultHistoryAlarmCardType 1.3.6.1.4.1.43.1.12.1.1.6.4.1.4
Card type of the card which caused the alarm.
OBJECT-TYPE    
  CardType  

faultHistoryAlarmCardNumber 1.3.6.1.4.1.43.1.12.1.1.6.4.1.5
Slot number of the card which caused the alarm.
OBJECT-TYPE    
  INTEGER 1..6  

faultHistoryAlarmPortNumber 1.3.6.1.4.1.43.1.12.1.1.6.4.1.6
Port number of the card which caused the alarm.
OBJECT-TYPE    
  INTEGER 1..8  

faultHistoryAlarmSetTime 1.3.6.1.4.1.43.1.12.1.1.6.4.1.7
The time when the alarm was set.
OBJECT-TYPE    
  TimeAndDate  

faultHistoryAlarmDescription 1.3.6.1.4.1.43.1.12.1.1.6.4.1.8
A readable string which describes the alarm.
OBJECT-TYPE    
  DisplayString  

faultHistoryAlarmClearTime 1.3.6.1.4.1.43.1.12.1.1.6.4.1.9
The time when the alarm was cleared.
OBJECT-TYPE    
  TimeAndDate