BIANCA-BRICK-X25-MIB

File: BIANCA-BRICK-X25-MIB.mib (66078 bytes)

Imported modules

SNMPv2-TC RFC1155-SMI RFC-1212

Imported symbols

DisplayString Counter TimeTicks
OBJECT-TYPE

Defined Types

HexValue  
INTEGER    

Date  
INTEGER    

X25LinkEntry  
SEQUENCE    
  x25LkIfIndex INTEGER
  x25LkAddr STRING
  x25LkMode INTEGER
  x25LkModulo INTEGER
  x25LkLIC INTEGER
  x25LkHIC INTEGER
  x25LkLTC INTEGER
  x25LkHTC INTEGER
  x25LkLOC INTEGER
  x25LkHOC INTEGER
  x25LkDefPktSize INTEGER
  x25LkDefWinSize INTEGER
  x25LkMaxPktSize INTEGER
  x25LkMaxWinSize INTEGER
  x25LkL2WinSize INTEGER
  x25LkL2RetrTimer INTEGER
  x25LkL2RetrCounter INTEGER
  x25LkL2SupervTimer INTEGER
  x25LkL2IdleTimer INTEGER
  x25LkState INTEGER
  x25LkNegotiation INTEGER
  x25LkDiscDelayTimer INTEGER
  x25LkCallDelayTimer INTEGER
  x25LkRestDelayTimer INTEGER

X25LinkPresetEntry  
SEQUENCE    
  x25LkPrIfIndex INTEGER
  x25LkPrAddr STRING
  x25LkPrMode INTEGER
  x25LkPrModulo INTEGER
  x25LkPrLIC INTEGER
  x25LkPrHIC INTEGER
  x25LkPrLTC INTEGER
  x25LkPrHTC INTEGER
  x25LkPrLOC INTEGER
  x25LkPrHOC INTEGER
  x25LkPrDefPktSize INTEGER
  x25LkPrDefWinSize INTEGER
  x25LkPrMaxPktSize INTEGER
  x25LkPrMaxWinSize INTEGER
  x25LkPrL2WinSize INTEGER
  x25LkPrL2RetrTimer INTEGER
  x25LkPrL2RetrCounter INTEGER
  x25LkPrL2SupervTimer INTEGER
  x25LkPrL2IdleTimer INTEGER
  x25LkPrNegotiation INTEGER
  x25LkPrDiscDelayTimer INTEGER
  x25LkPrCallDelayTimer INTEGER
  x25LkPrRestDelayTimer INTEGER

X25CallEntry  
SEQUENCE    
  x25CallSrcIfIndex INTEGER
  x25CallSrcLinkAddr STRING
  x25CallSrcVCNumber INTEGER
  x25CallDstIfIndex INTEGER
  x25CallDstLinkAddr STRING
  x25CallDstVCNumber INTEGER
  x25CallSrcAddr DisplayString
  x25CallDstAddr DisplayString
  x25CallProtocolId INTEGER
  x25CallFacilities STRING
  x25CallUserData DisplayString
  x25CallAge TimeTicks
  x25CallState INTEGER
  x25CallInPktSize INTEGER
  x25CallOutPktSize INTEGER
  x25CallInWinSize INTEGER
  x25CallOutWinSize INTEGER
  x25CallPktsSent Counter
  x25CallBytesSent Counter
  x25CallPktsRecvd Counter
  x25CallBytesRecvd Counter

X25CallHistoryEntry  
SEQUENCE    
  x25CallHistoryTime Date
  x25CallHistoryDuration INTEGER
  x25CallHistorySrcIfIndex INTEGER
  x25CallHistorySrcLinkAddr STRING
  x25CallHistorySrcVCNumber INTEGER
  x25CallHistoryDstIfIndex INTEGER
  x25CallHistoryDstLinkAddr STRING
  x25CallHistoryDstVCNumber INTEGER
  x25CallHistorySrcAddr DisplayString
  x25CallHistoryDstAddr DisplayString
  x25CallHistoryProtocolId INTEGER
  x25CallHistoryFacilities STRING
  x25CallHistoryUserData DisplayString
  x25CallHistoryInPktSize INTEGER
  x25CallHistoryOutPktSize INTEGER
  x25CallHistoryInWinSize INTEGER
  x25CallHistoryOutWinSize INTEGER
  x25CallHistoryPktsSent Counter
  x25CallHistoryBytesSent Counter
  x25CallHistoryPktsRecvd Counter
  x25CallHistoryBytesRecvd Counter
  x25CallHistoryClearCause INTEGER
  x25CallHistoryClearDiag INTEGER

X25RouteEntry  
SEQUENCE    
  x25RtSrcIfIndex INTEGER
  x25RtSrcLinkAddr STRING
  x25RtDstIfIndex INTEGER
  x25RtDstLinkAddr STRING
  x25RtDstAddrMode INTEGER
  x25RtSrcAddr DisplayString
  x25RtSrcNSAP DisplayString
  x25RtDstAddr DisplayString
  x25RtDstNSAP DisplayString
  x25RtProtocolId INTEGER
  x25RtCallUserData STRING
  x25RtRPOA INTEGER
  x25RtNUI DisplayString
  x25RtRewritingRule INTEGER
  x25RtMetric INTEGER
  x25RtCug INTEGER
  x25RtCugOutgoing INTEGER
  x25RtCugBilateral INTEGER

X25RewriteEntry  
SEQUENCE    
  x25RwRewritingRule INTEGER
  x25RwReverseCharging INTEGER
  x25RwRPOA INTEGER
  x25RwNUI DisplayString
  x25RwSrcAddr DisplayString
  x25RwSrcNSAP DisplayString
  x25RwDstAddr DisplayString
  x25RwDstNSAP DisplayString
  x25RwProtocolId INTEGER
  x25RwCallUserData STRING
  x25RwRespSrcAddr DisplayString
  x25RwRespSrcNSAP DisplayString
  x25RwRespDstAddr DisplayString
  x25RwRespDstNSAP DisplayString
  x25RwRespProtocolId INTEGER
  x25RwRespCallUserData STRING
  x25RwCug INTEGER
  x25RwCugOutgoing INTEGER
  x25RwCugBilateral INTEGER
  x25RwDstLinkAddr DisplayString

X25MprEntry  
SEQUENCE    
  x25MprIfIndex INTEGER
  x25MprMtu INTEGER
  x25MprEncapsulation INTEGER
  x25MprNumVC INTEGER
  x25MprMaxVC INTEGER
  x25MprWinSize INTEGER
  x25MprPktSize INTEGER
  x25MprShortHold INTEGER
  x25MprMaxRetries INTEGER
  x25MprBlockTime INTEGER
  x25MprAddr DisplayString

Defined Values

org 1.3
OBJECT IDENTIFIER    

dod 1.3.6
OBJECT IDENTIFIER    

internet 1.3.6.1
OBJECT IDENTIFIER    

private 1.3.6.1.4
OBJECT IDENTIFIER    

enterprises 1.3.6.1.4.1
OBJECT IDENTIFIER    

bintec 1.3.6.1.4.1.272
OBJECT IDENTIFIER    

bibo 1.3.6.1.4.1.272.4
OBJECT IDENTIFIER    

x25 1.3.6.1.4.1.272.4.6
OBJECT IDENTIFIER    

x25LinkTable 1.3.6.1.4.1.272.4.6.1
This table contains an entry for each active link. There may be mutiple active links per interface. For point-to- multipoint interfaces, the field x25LkAddr specifies the (MAC-) address of the partner, the link leads to. There may be also multiple links for a point-to-point interface in a multilink environment without a multilink- protocol joining the multiple links to a singe logical link.
OBJECT-TYPE    
  SEQUENCE OF  
    X25LinkEntry

x25LinkEntry 1.3.6.1.4.1.272.4.6.1.1
The x25LinkEntry is created automatically, when a link becomes active. The entry is also removed automatically, if a link becomes disconnected. It may be removed manually by setting the field x25LinkState to delete, which causes the related link to be disconnected.
OBJECT-TYPE    
  X25LinkEntry  

x25LkIfIndex 1.3.6.1.4.1.272.4.6.1.1.1
The index of the interface the link is running on. See ifTable.
OBJECT-TYPE    
  INTEGER  

x25LkAddr 1.3.6.1.4.1.272.4.6.1.1.2
On point-to-multipoint interfaces, this field contains the (MAC-)address of the partner, the link is leading to. It is empty for point-to-point interfaces, because there is only one partner at the other side.
OBJECT-TYPE    
  STRING  

x25LkMode 1.3.6.1.4.1.272.4.6.1.1.3
This field indicates wheter the Layer 3 on top of the link is operated in DTE or DCE mode. The difference is in the order of VC-assignment, the handling of a call collision and the range of allowed values of the cause field.
OBJECT-TYPE    
  INTEGER dte(1), dce(2)  

x25LkModulo 1.3.6.1.4.1.272.4.6.1.1.4
This field indicates whether the layer 3 on top of the link is in modulo 8 or in modulo 128 mode.
OBJECT-TYPE    
  INTEGER mod8(1), mod128(2)  

x25LkLIC 1.3.6.1.4.1.272.4.6.1.1.5
Lowest Incoming Channel as seen from the DTE. Zero means no incoming channels.
OBJECT-TYPE    
  INTEGER 0..4095  

x25LkHIC 1.3.6.1.4.1.272.4.6.1.1.6
Highest Incoming Channel as seen from the DTE. Zero means no incoming channels.
OBJECT-TYPE    
  INTEGER 0..4095  

x25LkLTC 1.3.6.1.4.1.272.4.6.1.1.7
Lowest Twoway Channel as seen from the DTE. Zero means no twoway channels.
OBJECT-TYPE    
  INTEGER 0..4095  

x25LkHTC 1.3.6.1.4.1.272.4.6.1.1.8
Highest Twoway Channel as seen from the DTE. Zero means no twoway channels.
OBJECT-TYPE    
  INTEGER 0..4095  

x25LkLOC 1.3.6.1.4.1.272.4.6.1.1.9
Lowest Outgoing Channel as seen from the DTE. Zero means no outgoing channels.
OBJECT-TYPE    
  INTEGER 0..4095  

x25LkHOC 1.3.6.1.4.1.272.4.6.1.1.10
Highest Outgoing Channel as seen from the DTE. Zero means no outgoing channels.
OBJECT-TYPE    
  INTEGER 0..4095  

x25LkDefPktSize 1.3.6.1.4.1.272.4.6.1.1.11
The default layer 3 packet size for this link.
OBJECT-TYPE    
  INTEGER p128(7), p256(8), p512(9), p1024(10), p2048(11), p4096(12)  

x25LkDefWinSize 1.3.6.1.4.1.272.4.6.1.1.12
The default window size. This is always less than 8, if the layer 3 is operated in modulo 8 mode.
OBJECT-TYPE    
  INTEGER 1..127  

x25LkMaxPktSize 1.3.6.1.4.1.272.4.6.1.1.13
The maximum allowable packet size for this link during X.25 packet size negotiation. If this field is set to unrestricted, the packet size will only be limited by the Mtu size of the interface, which is always the upper bound for the packet size.
OBJECT-TYPE    
  INTEGER unrestricted(1), p128(7), p256(8), p512(9), p1024(10), p2048(11), p4096(12)  

x25LkMaxWinSize 1.3.6.1.4.1.272.4.6.1.1.14
The maximum allowable window size for this link during window size negotiation.
OBJECT-TYPE    
  INTEGER 0..127  

x25LkL2WinSize 1.3.6.1.4.1.272.4.6.1.1.15
The layer 2 window size for this link.
OBJECT-TYPE    
  INTEGER 1..127  

x25LkL2RetrTimer 1.3.6.1.4.1.272.4.6.1.1.16
The retransmission timeout in milliseconds for the layer 2 of this link. If a frame is not acknowledged within this timeout, it will be retransmitted.
OBJECT-TYPE    
  INTEGER 100..30000  

x25LkL2RetrCounter 1.3.6.1.4.1.272.4.6.1.1.17
The retransmission counter for the layer 2 of this link. If a frame has been retransmitted more often than indicated by this object, the link will be reset or disconnected,
OBJECT-TYPE    
  INTEGER 1..127  

x25LkL2SupervTimer 1.3.6.1.4.1.272.4.6.1.1.18
The link-supervision timeout in milliseconds for the layer 2 of this link. This timer is started, when the link gets idle. An RR poll-sequence will be initiated, when this timeout expires.
OBJECT-TYPE    
  INTEGER 100..30000  

x25LkL2IdleTimer 1.3.6.1.4.1.272.4.6.1.1.19
The idle timer in milliseconds for the layer 2 of this link. If no VCs are established and the the link has been idle for the time specified by this object, the link will be disconnected. The value 0 means, the link should not be disconnected after the last VC has been cleared. A value of -1 means, that the link shall be kept up even if it get disconnected from the partner on the other end.
OBJECT-TYPE    
  INTEGER -1..30000  

x25LkState 1.3.6.1.4.1.272.4.6.1.1.20
This object contains the current state of the link. The link may be manually disconnected by setting this object to the value delete.
OBJECT-TYPE    
  INTEGER restart-pending(1), restart-collision(2), ready(3), disc-pending(4), reset-pending(5), sabm-pending(6), xid-pending(7), sabm-wait(8)  

x25LkNegotiation 1.3.6.1.4.1.272.4.6.1.1.21
This object determines whether packet-size and windows-size parameters are negotiated for outgoing calls. When set to never, outgoing calls are cleared if the call parameters differ from the default-settings. When set to when-necessary, negotiation is only performed if the call parameters differ from the default settings. When set to always, negotiation is always performed.
OBJECT-TYPE    
  INTEGER when-necessary(1), always(2), never(3)  

x25LkDiscDelayTimer 1.3.6.1.4.1.272.4.6.1.1.22
The disc delay timer in milliseconds for the layer 2 of this link (only outgoing links). This timer specifies the time interval between receiving of layer 2 disconnect and actual disconnect of link. If the partner want to disconnect the layer 2 and the time specified by this object expired, the link will be disconnected. The value 0 means, the link will be disconnected immediately after receiving of disconnect.
OBJECT-TYPE    
  INTEGER 0..3000  

x25LkCallDelayTimer 1.3.6.1.4.1.272.4.6.1.1.23
The call delay timer in milliseconds for the layer 3 of this link (only outgoing link). This timer specifies the time interval between restart procedure completion and virtual call setup. If restart procedure is completed and the time specified by this object expired, call packet will be sent. The value 0 means, call packet should be sent immediately after completion of restart procedure.
OBJECT-TYPE    
  INTEGER 0..5000  

x25LkRestDelayTimer 1.3.6.1.4.1.272.4.6.1.1.24
The Restart delay timer in milliseconds for this link. This timer specifies the time interval between establishment of layer 2 and sending of restart packet. If layer 2 is established and the time specified by this object expired, restart packet will be sent. The value 0 means, restart packet should be sent immediately after establishment of layer 2.
OBJECT-TYPE    
  INTEGER 0..15000  

x25LinkPresetTable 1.3.6.1.4.1.272.4.6.2
This table predefines the link-parameters to be used, when a link is created. If no entry is contained in this table for a particular link, it will be setup with the default values. In any case, the parameters finally choosen for a link are displayed in the x25LinkTable. For point-to-multipoint interfaces, the parameters for the link may be set for all connected partners (x25LkPrAddr is empty) of for the specific partners individually (x25LkPrAddr is the MAC-address of the partner).
OBJECT-TYPE    
  SEQUENCE OF  
    X25LinkPresetEntry

x25LinkPresetEntry 1.3.6.1.4.1.272.4.6.2.1
Entries in this table are created by defining a new value for the field x25LkPrIfIndex. Entries may be deleted by setting the field x25LkPrMode to the value delete. Please note, that changing the entries dont have influence on links being already established. To take effekt the according links have to be cleared either manually (see x25LinkTable) or by other means.
OBJECT-TYPE    
  X25LinkPresetEntry  

x25LkPrIfIndex 1.3.6.1.4.1.272.4.6.2.1.1
The interface index of the link to be predefined. This object identifies a row in the ifTable.
OBJECT-TYPE    
  INTEGER  

x25LkPrAddr 1.3.6.1.4.1.272.4.6.2.1.2
On point-to-point links, this field must be empty. On point-to-multipoint links, this field may be empty or set to a partners (MAC-) address. In the first case, the definition is valid for all links on the interface except for those having a specific predefiniton. In the second case the definition defines the link parameters for a specific partner.
OBJECT-TYPE    
  STRING  

x25LkPrMode 1.3.6.1.4.1.272.4.6.2.1.3
This field indicates, whether the link is initially operated in DTE or DCE mode. If a misconfiguration is detected, (DTE<->DTE od DCE<->DCE) the DTE/DCE assignement is done be means of the procedure defined in ISOxxxx.
OBJECT-TYPE    
  INTEGER dte(1), dce(2), delete(3)  

x25LkPrModulo 1.3.6.1.4.1.272.4.6.2.1.4
This object indicates, whether the link should be operated in modulo 8 or modulo 128 mode.
OBJECT-TYPE    
  INTEGER mod8(1), mod128(2)  

x25LkPrLIC 1.3.6.1.4.1.272.4.6.2.1.5
Lowest Incoming Channel as seen from the DTE. Zero means no incoming channels.
OBJECT-TYPE    
  INTEGER 0..4095  

x25LkPrHIC 1.3.6.1.4.1.272.4.6.2.1.6
Highest Incoming Channel as seen from the DTE. Zero means no incoming channels.
OBJECT-TYPE    
  INTEGER 0..4095  

x25LkPrLTC 1.3.6.1.4.1.272.4.6.2.1.7
Lowest Twoway Channel as seen from the DTE. Zero means no twoway channels.
OBJECT-TYPE    
  INTEGER 0..4095  

x25LkPrHTC 1.3.6.1.4.1.272.4.6.2.1.8
Highest Twoway Channel as seen from the DTE. Zero means no twoway channels.
OBJECT-TYPE    
  INTEGER 0..4095  

x25LkPrLOC 1.3.6.1.4.1.272.4.6.2.1.9
Lowest Outgoing Channel as seen from the DTE. Zero means no outgoing channels.
OBJECT-TYPE    
  INTEGER 0..4095  

x25LkPrHOC 1.3.6.1.4.1.272.4.6.2.1.10
Highest Outgoing Channel as seen from the DTE. Zero means no outgoing channels.
OBJECT-TYPE    
  INTEGER 0..4095  

x25LkPrDefPktSize 1.3.6.1.4.1.272.4.6.2.1.11
The Layer 3 packet size for this link.
OBJECT-TYPE    
  INTEGER p128(7), p256(8), p512(9), p1024(10), p2048(11), p4096(12)  

x25LkPrDefWinSize 1.3.6.1.4.1.272.4.6.2.1.12
The default window size. This must be less than 8, if the layer 3 is operated in modulo 8 mode.
OBJECT-TYPE    
  INTEGER 1..127  

x25LkPrMaxPktSize 1.3.6.1.4.1.272.4.6.2.1.13
The maximum allowable packet size for this link during X.25 packet size negotiation. If this field is set to unrestricted, the packet size will only be limited by the Mtu size of the interface, which is always the upper bound for the packet size.
OBJECT-TYPE    
  INTEGER unrestricted(1), p128(7), p256(8), p512(9), p1024(10), p2048(11), p4096(12)  

x25LkPrMaxWinSize 1.3.6.1.4.1.272.4.6.2.1.14
The maximum allowable window size for this link during window size negotiation.
OBJECT-TYPE    
  INTEGER 1..127  

x25LkPrL2WinSize 1.3.6.1.4.1.272.4.6.2.1.15
The layer 2 window size for this link.
OBJECT-TYPE    
  INTEGER 1..127  

x25LkPrL2RetrTimer 1.3.6.1.4.1.272.4.6.2.1.16
The retransmission timeout in milliseconds for the layer 2 of this link. If a frame is not acknowledged within this timeout, it will be retransmitted.
OBJECT-TYPE    
  INTEGER 100..30000  

x25LkPrL2RetrCounter 1.3.6.1.4.1.272.4.6.2.1.17
The retransmission counter for the layer 2 of this link. If a frame has been retransmitted more often than indicated by this object, the link will be reset or disconnected.
OBJECT-TYPE    
  INTEGER 1..127  

x25LkPrL2SupervTimer 1.3.6.1.4.1.272.4.6.2.1.18
The link-supervision timeout in milliseconds for the layer 2 of this link. This timer is started, when the link gets idle. An RR poll-sequence will be initiated, when this timeout expires.
OBJECT-TYPE    
  INTEGER 100..30000  

x25LkPrL2IdleTimer 1.3.6.1.4.1.272.4.6.2.1.19
The idle timer in milliseconds for the layer 2 of this link. If no VCs are established and the the link has been idle for the time specified by this object, the link will be disconnected. The value 0 means, the link should not be disconnected after the last VC has been cleared. A value of -1 means, that the link shall be kept up even if it get disconnected from the partner on the other end.
OBJECT-TYPE    
  INTEGER -1..30000  

x25LkPrNegotiation 1.3.6.1.4.1.272.4.6.2.1.20
This object determines whether packet-size and windows-size parameters are negotiated for outgoing calls. When set to never, outgoing calls are cleared if the call parameters differ from the default-settings. When set to when-necessary, negotiation is only performed if the call parameters differ from the default settings. When set to always, negotiation is always performed.
OBJECT-TYPE    
  INTEGER when-necessary(1), always(2), never(3)  

x25LkPrDiscDelayTimer 1.3.6.1.4.1.272.4.6.2.1.21
The disc delay timer in milliseconds for the layer 2 of this link (only outgoing links). This timer specifies the time interval between receiving of layer 2 disconnect and actual disconnect of link. If the partner want to disconnect the layer 2 and the time specified by this object expired, the link will be disconnected. The value 0 means, the link will be disconnected immediately after receiving of disconnect.
OBJECT-TYPE    
  INTEGER 0..3000  

x25LkPrCallDelayTimer 1.3.6.1.4.1.272.4.6.2.1.22
The call delay timer in milliseconds for the layer 3 of this link (only outgoing link). This timer specifies the time interval between restart procedure completion and virtual call setup. If restart procedure is completed and the time specified by this object expired, call packet will be sent. The value 0 means, call packet should be sent immediately after completion of restart procedure.
OBJECT-TYPE    
  INTEGER 0..5000  

x25LkPrRestDelayTimer 1.3.6.1.4.1.272.4.6.2.1.23
The Restart delay timer in milliseconds for this link. This timer specifies the time interval between establishment of layer 2 and sending of restart packet. If layer 2 is established and the time specified by this object expired, restart packet will be sent. The value 0 means, restart packet should be sent immediately after establishment of layer 2.
OBJECT-TYPE    
  INTEGER 0..15000  

x25CallTable 1.3.6.1.4.1.272.4.6.3
This table contains an entry for each active X25-call. Calls always lead from a source-link to a destination-link. An interface index of 1 denotates a pseudo interfaces corresponding to all locally terminated calls.
OBJECT-TYPE    
  SEQUENCE OF  
    X25CallEntry

x25CallEntry 1.3.6.1.4.1.272.4.6.3.1
The entries are created automatically, as soon as a call gets active. They are removed automatically as soon as a call gets completely cleared. A call may also be cleared manually by setting the x25CallState field of an entry to the value delete, which would also force the call to be cleared. The call data of a cleared call is copied to the x25CallHistoryTable.
OBJECT-TYPE    
  X25CallEntry  

x25CallSrcIfIndex 1.3.6.1.4.1.272.4.6.3.1.1
The interface index of the link, the call comes from. This object contains the value 1, when the call is originated locally.
OBJECT-TYPE    
  INTEGER  

x25CallSrcLinkAddr 1.3.6.1.4.1.272.4.6.3.1.2
The (MAC-)address of the link, the call comes from (if any)
OBJECT-TYPE    
  STRING  

x25CallSrcVCNumber 1.3.6.1.4.1.272.4.6.3.1.3
The virtual curcuit number of the call on the link, the call comes from.
OBJECT-TYPE    
  INTEGER 1..4095  

x25CallDstIfIndex 1.3.6.1.4.1.272.4.6.3.1.4
The interface index of the link, the call leads to. This object contains the value 1, when the link is terminated locally.
OBJECT-TYPE    
  INTEGER  

x25CallDstLinkAddr 1.3.6.1.4.1.272.4.6.3.1.5
The (MAC-)address of the link, the call leads to.
OBJECT-TYPE    
  STRING  

x25CallDstVCNumber 1.3.6.1.4.1.272.4.6.3.1.6
The virtual curcuit number of the call on the target link.
OBJECT-TYPE    
  INTEGER 1..4095  

x25CallSrcAddr 1.3.6.1.4.1.272.4.6.3.1.7
The calling address of the call as received on the source link.
OBJECT-TYPE    
  DisplayString  

x25CallDstAddr 1.3.6.1.4.1.272.4.6.3.1.8
The called address of the call as received on the source link.
OBJECT-TYPE    
  DisplayString  

x25CallProtocolId 1.3.6.1.4.1.272.4.6.3.1.9
The protocol id (the first four byte of the call user data) of the call as received from the source link.
OBJECT-TYPE    
  INTEGER  

x25CallFacilities 1.3.6.1.4.1.272.4.6.3.1.10
The facilities of the call as received from the source link.
OBJECT-TYPE    
  STRING  

x25CallUserData 1.3.6.1.4.1.272.4.6.3.1.11
The user data (whithout the protocol id) of the call as received from the source link.
OBJECT-TYPE    
  DisplayString  

x25CallAge 1.3.6.1.4.1.272.4.6.3.1.12
The age of the call since received from the source link.
OBJECT-TYPE    
  TimeTicks  

x25CallState 1.3.6.1.4.1.272.4.6.3.1.13
The current state of the call. A call may be cleared manually by setting this object to the value delete.
OBJECT-TYPE    
  INTEGER routing(1), call-pending(2), dataxfer(3), out-reset-pending(4), in-reset-pending(5), out-clear-pending(6), in-clear-pending(7)  

x25CallInPktSize 1.3.6.1.4.1.272.4.6.3.1.14
The packet size of packets being received by the caller, as negotiated by the negotiation procedure.
OBJECT-TYPE    
  INTEGER p2(1), p4(2), p8(3), p16(4), p32(5), p64(6), p128(7), p256(8), p512(9), p1024(10), p2048(11), p4096(12), p8192(13), p16384(14), p32768(15)  

x25CallOutPktSize 1.3.6.1.4.1.272.4.6.3.1.15
The packet size of packets being sent by the caller, as negotiated by the negotiation procedure.
OBJECT-TYPE    
  INTEGER p2(1), p4(2), p8(3), p16(4), p32(5), p64(6), p128(7), p256(8), p512(9), p1024(10), p2048(11), p4096(12), p8192(13), p16384(14), p32768(15)  

x25CallInWinSize 1.3.6.1.4.1.272.4.6.3.1.16
The window size of packets being received by the caller, as negotiated by the negotiation procedure.
OBJECT-TYPE    
  INTEGER 1..127  

x25CallOutWinSize 1.3.6.1.4.1.272.4.6.3.1.17
The window size of packets being sent by the caller, as negotiated by the negotiation procedure.
OBJECT-TYPE    
  INTEGER 1..127  

x25CallPktsSent 1.3.6.1.4.1.272.4.6.3.1.18
The number of all layer 3 packets (including RR/RNR/REJ) sent by the caller.
OBJECT-TYPE    
  Counter  

x25CallBytesSent 1.3.6.1.4.1.272.4.6.3.1.19
The number of data bytes sent in DATA and INTERRUPT packets by the caller.
OBJECT-TYPE    
  Counter  

x25CallPktsRecvd 1.3.6.1.4.1.272.4.6.3.1.20
The number of all layer 3 packets (including RR/RNR/REJ) received by the caller.
OBJECT-TYPE    
  Counter  

x25CallBytesRecvd 1.3.6.1.4.1.272.4.6.3.1.21
The number of data bytes received in DATA and INTERRUPT packets by the caller.
OBJECT-TYPE    
  Counter  

x25CallHistoryTable 1.3.6.1.4.1.272.4.6.4
This table provides call information for the last 10 calls after they have been cleared. Active call are not contained in the x25CallHistoryTable.
OBJECT-TYPE    
  SEQUENCE OF  
    X25CallHistoryEntry

x25CallHistoryEntry 1.3.6.1.4.1.272.4.6.4.1
Entries are created automatically, when a call is cleared completely. The first entry is deleted automatcally, if a new entry would be the 11th entry in the table.
OBJECT-TYPE    
  X25CallHistoryEntry  

x25CallHistoryTime 1.3.6.1.4.1.272.4.6.4.1.1
Date and time, when the call was received.
OBJECT-TYPE    
  Date  

x25CallHistoryDuration 1.3.6.1.4.1.272.4.6.4.1.2
Duration of the call in seconds.
OBJECT-TYPE    
  INTEGER  

x25CallHistorySrcIfIndex 1.3.6.1.4.1.272.4.6.4.1.3
Interface index of the link, the call came from.
OBJECT-TYPE    
  INTEGER  

x25CallHistorySrcLinkAddr 1.3.6.1.4.1.272.4.6.4.1.4
(MAC-)address of the link, the call came from.
OBJECT-TYPE    
  STRING  

x25CallHistorySrcVCNumber 1.3.6.1.4.1.272.4.6.4.1.5
Virtual Curcuit Number on the link, the call came from.
OBJECT-TYPE    
  INTEGER 1..4095  

x25CallHistoryDstIfIndex 1.3.6.1.4.1.272.4.6.4.1.6
Interface index of the link, the call leads to.
OBJECT-TYPE    
  INTEGER  

x25CallHistoryDstLinkAddr 1.3.6.1.4.1.272.4.6.4.1.7
(MAC-)address of the link, the call leads to.
OBJECT-TYPE    
  STRING  

x25CallHistoryDstVCNumber 1.3.6.1.4.1.272.4.6.4.1.8
Virtual Curcuit Number on the link, the call leads to.
OBJECT-TYPE    
  INTEGER 1..4095  

x25CallHistorySrcAddr 1.3.6.1.4.1.272.4.6.4.1.9
The calling party number as received from the source link.
OBJECT-TYPE    
  DisplayString  

x25CallHistoryDstAddr 1.3.6.1.4.1.272.4.6.4.1.10
The called party number as received from the source link.
OBJECT-TYPE    
  DisplayString  

x25CallHistoryProtocolId 1.3.6.1.4.1.272.4.6.4.1.11
The Protocol ID of the call (first four bytes of the call user data field) as received from the source link.
OBJECT-TYPE    
  INTEGER  

x25CallHistoryFacilities 1.3.6.1.4.1.272.4.6.4.1.12
The facility field of the call as received from the source link.
OBJECT-TYPE    
  STRING  

x25CallHistoryUserData 1.3.6.1.4.1.272.4.6.4.1.13
The call user data behind the protocol ID as received from the source link
OBJECT-TYPE    
  DisplayString  

x25CallHistoryInPktSize 1.3.6.1.4.1.272.4.6.4.1.14
The packet size of packets being received by the caller, as negotiated by the negotiation procedure.
OBJECT-TYPE    
  INTEGER p2(1), p4(2), p8(3), p16(4), p32(5), p64(6), p128(7), p256(8), p512(9), p1024(10), p2048(11), p4096(12), p8192(13), p16384(14), p32768(15)  

x25CallHistoryOutPktSize 1.3.6.1.4.1.272.4.6.4.1.15
The packet size of packets being sent by the caller, as negotiated by the negotiation procedure.
OBJECT-TYPE    
  INTEGER p2(1), p4(2), p8(3), p16(4), p32(5), p64(6), p128(7), p256(8), p512(9), p1024(10), p2048(11), p4096(12), p8192(13), p16384(14), p32768(15)  

x25CallHistoryInWinSize 1.3.6.1.4.1.272.4.6.4.1.16
The window size of packets being received by the caller, as negotiated by the negotiation procedure.
OBJECT-TYPE    
  INTEGER 1..127  

x25CallHistoryOutWinSize 1.3.6.1.4.1.272.4.6.4.1.17
The window size of packets being sent by the caller, as negotiated by the negotiation procedure.
OBJECT-TYPE    
  INTEGER 1..127  

x25CallHistoryPktsSent 1.3.6.1.4.1.272.4.6.4.1.18
The number of all layer 3 packets (including RR/RNR/REJ) sent by the caller.
OBJECT-TYPE    
  Counter  

x25CallHistoryBytesSent 1.3.6.1.4.1.272.4.6.4.1.19
The number of data bytes sent in DATA and INTERRUPT packets by the caller.
OBJECT-TYPE    
  Counter  

x25CallHistoryPktsRecvd 1.3.6.1.4.1.272.4.6.4.1.20
The number of all layer 3 packets (including RR/RNR/REJ) received by the caller.
OBJECT-TYPE    
  Counter  

x25CallHistoryBytesRecvd 1.3.6.1.4.1.272.4.6.4.1.21
The number of data bytes received in DATA and INTERRUPT packets by the caller.
OBJECT-TYPE    
  Counter  

x25CallHistoryClearCause 1.3.6.1.4.1.272.4.6.4.1.22
The clearing cause of the call as received in the first clear packet. A value of -1 means, no cause was received.
OBJECT-TYPE    
  INTEGER -1..255  

x25CallHistoryClearDiag 1.3.6.1.4.1.272.4.6.4.1.23
The clearing diagnostics of the call as received in the first clear packet. A value of -1 means, no diagnostics was received.
OBJECT-TYPE    
  INTEGER -1..255  

x25RouteTable 1.3.6.1.4.1.272.4.6.5
The X.25 Routing Table specifies the target link for different call parameters. For each incoming call the route table will be searched for a matching entry. If multiple entries match the call parameters, a metric defines which of them to use. A route is only used, if the state of the target interface is up or dormant (see mib2). Also the state of the link is used to determine wether to use the route or not. With this mechanism, a rerouting scheme can be implemented.
OBJECT-TYPE    
  SEQUENCE OF  
    X25RouteEntry

x25RouteEntry 1.3.6.1.4.1.272.4.6.5.1
Entries can only be created and deleted manually.
OBJECT-TYPE    
  X25RouteEntry  

x25RtSrcIfIndex 1.3.6.1.4.1.272.4.6.5.1.1
The originating interface index of the call. If this object is set to zero, the originating interface index will not be checked for the matching process. If this field is set to one, the route is only valid for call originating locally.
OBJECT-TYPE    
  INTEGER  

x25RtSrcLinkAddr 1.3.6.1.4.1.272.4.6.5.1.2
The originating (MAC-)address of the call. If this object is a zero length string, the originating address will not be checked for the matching process.
OBJECT-TYPE    
  STRING  

x25RtDstIfIndex 1.3.6.1.4.1.272.4.6.5.1.3
The interface index the call has to be sent to. If this value is set to one, the call will be used locally. If the value is set to zero, the call will be refused. The routing entry will only be used if the destination interface status is up or dormant. Additionally the target link must be in the state ready, if it is permanently activated, i.e. the x25LkL2IdleTimer is set to -1.
OBJECT-TYPE    
  INTEGER  

x25RtDstLinkAddr 1.3.6.1.4.1.272.4.6.5.1.4
The (MAC-)address of the station, the call has to be sent to. This object is ignored for point-to-point interfaces.
OBJECT-TYPE    
  STRING  

x25RtDstLinkAddrMode 1.3.6.1.4.1.272.4.6.5.1.5
This object specifies the way, the destination link address is generated. Default will use the default method for the target interface. When direct is selected, the destination address is taken from the route entry. Set to rule(4), the the address is generated according the rule defined in the x25RwDstLinkAddr entry of the X25RwTable. Other methods will be developed in the future.
OBJECT-TYPE    
  INTEGER default(1), direct(2), delete(3), rule(4), auto(5)  

x25RtSrcAddr 1.3.6.1.4.1.272.4.6.5.1.6
The source X.121 address in the X25 call packet. If empty, the source address will not be matched. Extended Adresses are indicated by a leading '@'. The wildcards '*', '?', '[', ']', '{', '}' may be used.
OBJECT-TYPE    
  DisplayString  

x25RtSrcNSAP 1.3.6.1.4.1.272.4.6.5.1.7
The source NSAP in the X25 call packet. If empty, the source NSAP will not be matched. The NSAP is preceeded by an 'X' if it is an OSI compatible NSAP or by a 'N' if the NSAP is in a not OSI compatible format. The wildcards '*', '?', '[', ']', '{', '}' may be used.
OBJECT-TYPE    
  DisplayString  

x25RtDstAddr 1.3.6.1.4.1.272.4.6.5.1.8
The target X.121 address in the X25 call packet. If empty, the source address will not be matched. Extended Adresses are indicated by a leading '@'. The wildcards '*', '?', '[', ']', '{', '}' may be used.
OBJECT-TYPE    
  DisplayString  

x25RtDstNSAP 1.3.6.1.4.1.272.4.6.5.1.9
The target NSAP in the X25 call packet. If empty, the source address will not be matched. The NSAP is preceeded by an 'X' if it is an OSI compatible NSAP or by a 'N' if the NSAP is in a not OSI compatible format. The wildcards '*', '?', '[', ']', '{', '}' may be used.
OBJECT-TYPE    
  DisplayString  

x25RtProtocolId 1.3.6.1.4.1.272.4.6.5.1.10
The protocol id of the X25 call packet. The protocol id will not be used for the matching process, when this object is set to -1
OBJECT-TYPE    
  INTEGER  

x25RtCallUserData 1.3.6.1.4.1.272.4.6.5.1.11
The call user data field of the X25 call packet behind the protocol id. If empty, the call user data field will not be used for matching.
OBJECT-TYPE    
  STRING  

x25RtRPOA 1.3.6.1.4.1.272.4.6.5.1.12
This object will be compared to the first value in the list of RPOAs in the X25 call packet, if not set to -1.
OBJECT-TYPE    
  INTEGER -1..9999  

x25RtNUI 1.3.6.1.4.1.272.4.6.5.1.13
This object will be compared to the NUI facility supplied with the call. If this object is an empty string, the NUI facility will not be used for the matching process.
OBJECT-TYPE    
  DisplayString  

x25RtRewritingRule 1.3.6.1.4.1.272.4.6.5.1.14
This Object specifies a rewriting rule in the X25 Rewriting Rule table. The call packed will be processed according to this rewriting rule before the call is being delivered. If this value is set to zero, no rewriting will take place.
OBJECT-TYPE    
  INTEGER 0..999999  

x25RtMetric 1.3.6.1.4.1.272.4.6.5.1.15
This object specifies a metric similar to the metric of an IP routing entry. If a call matches multiple entries in the X25 routing table, the routing entry with the lowest value of Metric will be used to route the call.
OBJECT-TYPE    
  INTEGER 0..255  

x25RtCug 1.3.6.1.4.1.272.4.6.5.1.16
This object will be compared to the CUG facility supplied with the call, if not set to -1.
OBJECT-TYPE    
  INTEGER -1..9999  

x25RtCugOutgoing 1.3.6.1.4.1.272.4.6.5.1.17
This object will be compared to the Outgoing CUG facility supplied with the call, if not set to -1.
OBJECT-TYPE    
  INTEGER -1..9999  

x25RtCugBilateral 1.3.6.1.4.1.272.4.6.5.1.18
This object will be compared to the Bilateral CUG facility supplied with the call, if not set to -1.
OBJECT-TYPE    
  INTEGER -1..9999  

x25RewriteTable 1.3.6.1.4.1.272.4.6.6
This Table contains entries, that describe different rules of rewriting the call parameters before delivering a call. Which entry in this table is used, will be determined by the route table.
OBJECT-TYPE    
  SEQUENCE OF  
    X25RewriteEntry

x25RewriteEntry 1.3.6.1.4.1.272.4.6.6.1
Tok_String
OBJECT-TYPE    
  X25RewriteEntry  

x25RwRewritingRule 1.3.6.1.4.1.272.4.6.6.1.1
The unique number of the rewriting rule.
OBJECT-TYPE    
  INTEGER 1..999999  

x25RwReverseCharging 1.3.6.1.4.1.272.4.6.6.1.2
This object describes what to do with the reverse charging facility.
OBJECT-TYPE    
  INTEGER dont-change(1), set(2), clear(3), delete(4)  

x25RwRPOA 1.3.6.1.4.1.272.4.6.6.1.3
This object describes what to do with the rpoa facility.
OBJECT-TYPE    
  INTEGER dont-change(1), remove-first(2)  

x25RwNUI 1.3.6.1.4.1.272.4.6.6.1.4
This object contains the new value of the NUI facility. If this object is an empty string, the NUI facility will not be changed.
OBJECT-TYPE    
  DisplayString  

x25RwSrcAddr 1.3.6.1.4.1.272.4.6.6.1.5
Specifies how to rewrite the source address. Digits will be set directly to the new address. A '.' will move a digit from the old address to the new address. A '*' will move all remaining digits from the old address to the new address. A '%' will delete a digit from the old address. Please note that the eventually leading '@' (indicating extended adressing) is handled execatly like digits. If this object is empty, the source address will not be changed.
OBJECT-TYPE    
  DisplayString  

x25RwSrcNSAP 1.3.6.1.4.1.272.4.6.6.1.6
Specifies how to rewrite the source NSAP. Digits will be set directly to the new NSAP. A '.' will move a digit from the old NSAP to the new NSAP. A '*' will move all remaining digits from the old NSAP to the new NSAP. A '%' will delete a digit from the old NSAP. Please note that the eventually leading '@' (indicating extended adressing) is handled execatly like digits. If this object is empty, the source NSAP will not be changed.
OBJECT-TYPE    
  DisplayString  

x25RwDstAddr 1.3.6.1.4.1.272.4.6.6.1.7
Specifies how to rewrite the destination address. Digits will be set directly to the new address. A '.' will move a digit from the old address to the new address. A '*' will move all remaining digits from the old address to the new address. A '%' will delete a digit from the old address. Please note that the eventually leading '@' (indicating extended adressing) is handled execatly like digits. If this object is empty, the destination address will not be changed.
OBJECT-TYPE    
  DisplayString  

x25RwDstNSAP 1.3.6.1.4.1.272.4.6.6.1.8
Specifies how to rewrite the destination NSAP. Digits will be set directly to the new NSAP. A '.' will move a digit from the old NSAP to the new NSAP. A '*' will move all remaining digits from the old NSAP to the new NSAP. A '%' will delete a digit from the old NSAP. Please note that the eventually leading '@' (indicating extended adressing) is handled execatly like digits. If this object is empty, the destination NSAP will not be changed.
OBJECT-TYPE    
  DisplayString  

x25RwProtocolId 1.3.6.1.4.1.272.4.6.6.1.9
This object specifies the new value of the protocol id field. The protocol id field will not be changed, if this object is set to -1
OBJECT-TYPE    
  INTEGER  

x25RwCallUserData 1.3.6.1.4.1.272.4.6.6.1.10
The new value of the call user data field. The call user data field will not be changed, if this object is an empty string. A leading '%' will be ignored. This allows to delete the call user data portion of a call packet by setting this object to a single '%'.
OBJECT-TYPE    
  STRING  

x25RwRespSrcAddr 1.3.6.1.4.1.272.4.6.6.1.11
Specifies how to rewrite the source address of the call accepted packet. Digits will be set directly to the new address. A '.' will move a digit from the old address to the new address. A '*' will move all remaining digits from the old address to the new address. A '%' will delete a digit from the old address. Please note that the eventually leading '@' (indicating extended adressing) is handled execatly like digits. If this object is empty, the source address will not be changed.
OBJECT-TYPE    
  DisplayString  

x25RwRespSrcNSAP 1.3.6.1.4.1.272.4.6.6.1.12
Specifies how to rewrite the source NSAP in the call accepted packet. Digits will be set directly to the new NSAP. A '.' will move a digit from the old NSAP to the new NSAP. A '*' will move all remaining digits from the old NSAP to the new NSAP. A '%' will delete a digit from the old NSAP. Please note that the eventually leading '@' (indicating extended adressing) is handled execatly like digits. If this object is empty, the source NSAP will not be changed.
OBJECT-TYPE    
  DisplayString  

x25RwRespDstAddr 1.3.6.1.4.1.272.4.6.6.1.13
Specifies how to rewrite the destination address of the call accepted packet. Digits will be set directly to the new address. A '.' will move a digit from the old address to the new address. A '*' will move all remaining digits from the old address to the new address. A '%' will delete a digit from the old address. Please note that the eventually leading '@' (indicating extended adressing) is handled execatly like digits. If this object is empty, the destination address will not be changed.
OBJECT-TYPE    
  DisplayString  

x25RwRespDstNSAP 1.3.6.1.4.1.272.4.6.6.1.14
Specifies how to rewrite the destination NSAP in the call accepted packet. Digits will be set directly to the new NSAP. A '.' will move a digit from the old NSAP to the new NSAP. A '*' will move all remaining digits from the old NSAP to the new NSAP. A '%' will delete a digit from the old NSAP. Please note that the eventually leading '@' (indicating extended adressing) is handled execatly like digits. If this object is empty, the destination NSAP will not be changed.
OBJECT-TYPE    
  DisplayString  

x25RwRespProtocolId 1.3.6.1.4.1.272.4.6.6.1.15
This object contains the new value of the ProtocolID field of the call accepted packet. The ProtocolID will not be changed, if this object is set to -1.
OBJECT-TYPE    
  INTEGER  

x25RwRespCallUserData 1.3.6.1.4.1.272.4.6.6.1.16
The new value of the call user data field of the call accepted packet. The call user data field will not be changed, if this object is an empty string. A leading '%' will be ignored. This allows to delete the call user data portion of a call accepted packet by setting this object to a single '%'.
OBJECT-TYPE    
  STRING  

x25RwCug 1.3.6.1.4.1.272.4.6.6.1.17
This object contains the new value of the CUG facility. If this object is set to -1, the CUG facility will not be changed. The CUG facility will be removed, if this object is set to -2.
OBJECT-TYPE    
  INTEGER -2..9999  

x25RwCugOutgoing 1.3.6.1.4.1.272.4.6.6.1.18
This object contains the new value of the Outgoing CUG facility. If this object is set to -1, the Outgoing CUG facility will not be changed. The Outgoing CUG facility will be removed, if this object is set to -2.
OBJECT-TYPE    
  INTEGER -2..9999  

x25RwCugBilateral 1.3.6.1.4.1.272.4.6.6.1.19
This object contains the new value of the Bilateral CUG facility. If this object is set to -1, the Bilateral CUG facility will not be changed. The Bilateral CUG facility will be removed, if this object is set to -2.
OBJECT-TYPE    
  INTEGER -2..9999  

x25RwDstLinkAddr 1.3.6.1.4.1.272.4.6.6.1.20
Specifies a rule how to generate a destination link address from destination X.25 address or destination NSAP. Digits will be set directly to the new address. A '.' will move a digit from the old address to the new address. A '*' will move all remaining digits from the old address to the new address. A '%' will delete a digit from the old address. The optional leading digit specifies the protocol to be used for the Layer 1 or the type of destination address to be generated (IP or MAC), this is followed by a mandatory character 'X' (use X.25 address for conversion) or 'N' (use NSAP).
OBJECT-TYPE    
  DisplayString  

x25MprTable 1.3.6.1.4.1.272.4.6.7
This table contains an entry for each partner reachable via X.25 for Multiprotocol over X.25 according to RFC 1356. Entries in this table are created manually and will result to the creation of a multiprotocol routing interface in the ifTable. This interface can than be used by higher level protocols like ip, ipx and bridging. The object x25MprIfIndex shall be set to 0 for creation of new entries. The BRICK will allocate the next free interface index and assign it ti x25MprIfIndex. Rows of this table can be deleted by setting the object x25MprEncapsulation to the value delete.
OBJECT-TYPE    
  SEQUENCE OF  
    X25MprEntry

x25MprEntry 1.3.6.1.4.1.272.4.6.7.1
Tok_String
OBJECT-TYPE    
  X25MprEntry  

x25MprIfIndex 1.3.6.1.4.1.272.4.6.7.1.1
This object contains an interface index and assigns the row to an entry in ifTable. When creating new entries in the table, the value of this object shall be set to 0. The next free ifIndex value is than allocated by the BRICK and assigned to the object. At the same time a new interface is created in the IfTable.
OBJECT-TYPE    
  INTEGER  

x25MprMtu 1.3.6.1.4.1.272.4.6.7.1.2
The Maximum transfer unit to be used with the interface, the row is describing.
OBJECT-TYPE    
  INTEGER 576..8180  

x25MprEncapsulation 1.3.6.1.4.1.272.4.6.7.1.3
This object specifies the encapsulation method to be used. If this object is set to ip_rfc877, the RFC877 compatible encapsulation is selected. The relating interface is only capabable of transferring IP datagrams. All other protocols are not supported. Virtual channels are established only with the CUD field set to CC. If this object is set to ip, the relating interface is also only capable of forwarding IP datagrams. However, the virtual channels are setup with the CUD field set to 80 00 00 00 08 00. The encapsulation ipx allows only forwarding of IPX datagrams. VCs are established using a CUD field of 80 00 00 00 81 37. If this object is set to mpr, the corresponding corresponding interface is capable of IP, IPX and BRIDGING. The different protocols are multiplexed over the same VC. The CUD field is set to 00.
OBJECT-TYPE    
  INTEGER ip-rfc877(1), ip(2), ipx(3), mpr(4), delete(5)  

x25MprNumVC 1.3.6.1.4.1.272.4.6.7.1.4
This object specifies the number of VCs used with the corresponding interface. The BRICK will always try to have that many VCs available for the relating interface.
OBJECT-TYPE    
  INTEGER 0..255  

x25MprMaxVC 1.3.6.1.4.1.272.4.6.7.1.5
This object specifies the maximum number of VCs used with the corresponding interface. It shall be greater or equal to x25MprNumVC.
OBJECT-TYPE    
  INTEGER 0..255  

x25MprWinSize 1.3.6.1.4.1.272.4.6.7.1.6
This object describes the window size to be used for outgoing X.25 virtual calls.
OBJECT-TYPE    
  INTEGER 1..7  

x25MprPktSize 1.3.6.1.4.1.272.4.6.7.1.7
This object describes the packet size, to be used for outgoing X.25 calls. Please note that this parameter is independant of the x25MprMtu parameter.
OBJECT-TYPE    
  INTEGER p128(7), p256(8), p512(9), p1024(10), p2048(11), p4096(12)  

x25MprShortHold 1.3.6.1.4.1.272.4.6.7.1.8
This object specifies the time of inactivity in seconds, after which the VCs are disconnected automatically.
OBJECT-TYPE    
  INTEGER 0..65535  

x25MprMaxRetries 1.3.6.1.4.1.272.4.6.7.1.9
This object specifies the maximum number of tries for X.25 call establishement. If the BRICK has tried to establish the call for this many times, the interface is in the blocked state for a time specified by x25MprBlockTime. During the blocked state, no more tries are made.
OBJECT-TYPE    
  INTEGER 1..255  

x25MprBlockTime 1.3.6.1.4.1.272.4.6.7.1.10
This object describes the amount of time, the corresponding interface remains in the blocked state after too many tries to establish the X.25 call.
OBJECT-TYPE    
  INTEGER 0..65536  

x25MprAddr 1.3.6.1.4.1.272.4.6.7.1.11
The X.25 address to be used with this interface. A leading @ indicates extended adressing.
OBJECT-TYPE    
  DisplayString  

x25LocalPadCall 1.3.6.1.4.1.272.4.6.10
This object specifies wether a PAD Call (PID=1) routed to the local X.25 entity (ifIndex=1) should be accepted to allow for a remote login via X.25. This may be disabled for security reasons by setting this object do dont-accept.
OBJECT-TYPE    
  INTEGER accept(1), dont-accept(2)  

x25LocalAddr 1.3.6.1.4.1.272.4.6.11
The X.25 address to be used as originating address for outgoing X.25 call from this BRICK. A leading @ indicates extended adressing.
OBJECT-TYPE    
  DisplayString  

x25Rerouting 1.3.6.1.4.1.272.4.6.12
This object specifies whether a rerouting request should be accepted to establish connection to another server. This is only relevant for x29 rerouting.
OBJECT-TYPE    
  INTEGER allow(1), disallow(2)  

x25HistoryMaxEntries 1.3.6.1.4.1.272.4.6.13
Maximum number of x25CallHistory entries in memory.
OBJECT-TYPE    
  INTEGER 0..255  

x25AccountingTemplate 1.3.6.1.4.1.272.4.6.14
Specifies the format of accounting messages sent by the syslog protocol. The format can consist of any order of the following variables. Tag Meaning %S Date and Time the connection was established; in DD.MM.YY/HH:MM:SS format. %d The duration of the connection in seconds. %z The X25 source address. %Z The X25 destination address. %y Total number of bytes received over the connection. %Y Total number of bytes sent over the connection. %g Total packets received over the connection. %G Total packets sent over the connection. %c The X25 clear cause. %C The X25 clear diagnostic. %f The source interface. %F The destination interface. %v The source virtual channel number. %V The destination virtual channel number. The default accounting template setting contains the following tags: %S,%d,%z,%Z,%y,%Y,%g,%G,%c,%C.
OBJECT-TYPE    
  DisplayString Size(0..255)