BGP-MPLS-LAYER3-VPN-MULTICAST-MIB
File:
BGP-MPLS-LAYER3-VPN-MULTICAST-MIB.mib (75076 bytes)
Imported modules
Imported symbols
Defined Types
| MvpnGenericEntry |
|
| SEQUENCE |
|
|
|
| |
mvpnGenMvrfLastAction |
INTEGER |
|
| |
mvpnGenMvrfLastActionTime |
DateAndTime |
|
| |
mvpnGenMvrfCreationTime |
DateAndTime |
|
| |
mvpnGenCmcastRouteProtocol |
INTEGER |
|
| |
mvpnGenIpmsiInfo |
RowPointer |
|
| |
mvpnGenInterAsPmsiInfo |
RowPointer |
|
| |
mvpnGenUmhSelection |
INTEGER |
|
| |
mvpnGenCustomerSiteType |
INTEGER |
|
| MvpnBgpEntry |
|
| SEQUENCE |
|
|
|
| |
mvpnBgpMode |
INTEGER |
|
| |
mvpnBgpVrfRouteImportExtendedCommunity |
MplsL3VpnRouteDistinguisher |
|
| |
mvpnBgpSrcASExtendedCommunity |
Unsigned32 |
|
| |
mvpnBgpMsgRateLimit |
Unsigned32 |
|
| |
mvpnBgpMaxSpmsiAdRoutes |
Unsigned32 |
|
| |
mvpnBgpMaxSpmsiAdRouteFreq |
Unsigned32 |
|
| |
mvpnBgpMaxSrcActiveAdRoutes |
Unsigned32 |
|
| |
mvpnBgpMaxSrcActiveAdRouteFreq |
Unsigned32 |
|
| MvpnPmsiEntry |
|
| SEQUENCE |
|
|
|
| |
mvpnPmsiTunnelIfIndex |
InterfaceIndex |
|
| |
mvpnPmsiRD |
MplsL3VpnRouteDistinguisher |
|
| |
mvpnPmsiTunnelType |
L2L3VpnMcastProviderTunnelType |
|
| |
mvpnPmsiTunnelAttribute |
RowPointer |
|
| |
mvpnPmsiTunnelPimGroupAddrType |
InetAddressType |
|
| |
mvpnPmsiTunnelPimGroupAddr |
InetAddress |
|
| |
mvpnPmsiEncapsulationType |
INTEGER |
|
| MvpnSpmsiEntry |
|
| SEQUENCE |
|
|
|
| |
mvpnSpmsiCmcastGroupAddrType |
InetAddressType |
|
| |
mvpnSpmsiCmcastGroupAddr |
InetAddress |
|
| |
mvpnSpmsiCmcastGroupPrefixLen |
InetAddressPrefixLength |
|
| |
mvpnSpmsiCmcastSourceAddrType |
InetAddressType |
|
| |
mvpnSpmsiCmcastSourceAddr |
InetAddress |
|
| |
mvpnSpmsiCmcastSourcePrefixLen |
InetAddressPrefixLength |
|
| |
mvpnSpmsiPmsiPointer |
RowPointer |
|
| MvpnAdvtStatsEntry |
|
| SEQUENCE |
|
|
|
| |
mvpnAdvtType |
INTEGER |
|
| |
mvpnAdvtPeerAddrType |
InetAddressType |
|
| |
mvpnAdvtPeerAddr |
InetAddress |
|
| |
mvpnAdvtSent |
Counter32 |
|
| |
mvpnAdvtReceived |
Counter32 |
|
| |
mvpnAdvtReceivedError |
Counter32 |
|
| |
mvpnAdvtReceivedMalformedTunnelType |
Counter32 |
|
| |
mvpnAdvtReceivedMalformedTunnelId |
Counter32 |
|
| |
mvpnAdvtLastSentTime |
DateAndTime |
|
| |
mvpnAdvtLastReceivedTime |
DateAndTime |
|
| |
mvpnAdvtCounterDiscontinuityTime |
TimeStamp |
|
| MvpnMrouteEntry |
|
| SEQUENCE |
|
|
|
| |
mvpnMrouteCmcastGroupAddrType |
InetAddressType |
|
| |
mvpnMrouteCmcastGroupAddr |
InetAddress |
|
| |
mvpnMrouteCmcastGroupPrefixLength |
InetAddressPrefixLength |
|
| |
mvpnMrouteCmcastSourceAddrType |
InetAddressType |
|
| |
mvpnMrouteCmcastSourceAddrs |
InetAddress |
|
| |
mvpnMrouteCmcastSourcePrefixLength |
InetAddressPrefixLength |
|
| |
mvpnMrouteUpstreamNeighborAddrType |
InetAddressType |
|
| |
mvpnMrouteUpstreamNeighborAddr |
InetAddress |
|
| |
mvpnMrouteInIfIndex |
InterfaceIndexOrZero |
|
| |
mvpnMrouteExpiryTime |
TimeTicks |
|
| |
mvpnMrouteProtocol |
IANAipMRouteProtocol |
|
| |
mvpnMrouteRtProtocol |
IANAipRouteProtocol |
|
| |
mvpnMrouteRtAddrType |
InetAddressType |
|
| |
mvpnMrouteRtAddr |
InetAddress |
|
| |
mvpnMrouteRtPrefixLength |
InetAddressPrefixLength |
|
| |
mvpnMrouteRtType |
INTEGER |
|
| |
mvpnMrouteOctets |
Counter64 |
|
| |
mvpnMroutePkts |
Counter64 |
|
| |
mvpnMrouteTtlDroppedOctets |
Counter64 |
|
| |
mvpnMrouteTtlDroppedPackets |
Counter64 |
|
| |
mvpnMrouteDroppedInOctets |
Counter64 |
|
| |
mvpnMrouteDroppedInPackets |
Counter64 |
|
| |
mvpnMroutePmsiPointer |
RowPointer |
|
| |
mvpnMrouteNumberOfLocalReplication |
Unsigned32 |
|
| |
mvpnMrouteNumberOfRemoteReplication |
Unsigned32 |
|
| |
mvpnMrouteCounterDiscontinuityTime |
TimeStamp |
|
| MvpnMrouteNextHopEntry |
|
| SEQUENCE |
|
|
|
| |
mvpnMrouteNextHopGroupAddrType |
InetAddressType |
|
| |
mvpnMrouteNextHopGroupAddr |
InetAddress |
|
| |
mvpnMrouteNextHopGroupPrefixLength |
InetAddressPrefixLength |
|
| |
mvpnMrouteNextHopSourceAddrType |
InetAddressType |
|
| |
mvpnMrouteNextHopSourceAddrs |
InetAddress |
|
| |
mvpnMrouteNextHopSourcePrefixLength |
InetAddressPrefixLength |
|
| |
mvpnMrouteNextHopIfIndex |
InterfaceIndex |
|
| |
mvpnMrouteNextHopAddrType |
InetAddressType |
|
| |
mvpnMrouteNextHopAddr |
InetAddress |
|
| |
mvpnMrouteNextHopState |
INTEGER |
|
| |
mvpnMrouteNextHopExpiryTime |
TimeTicks |
|
| |
mvpnMrouteNextHopClosestMemberHops |
Unsigned32 |
|
| |
mvpnMrouteNextHopProtocol |
IANAipMRouteProtocol |
|
| |
mvpnMrouteNextHopOctets |
Counter64 |
|
| |
mvpnMrouteNextHopPkts |
Counter64 |
|
| |
mvpnMrouteNextHopCounterDiscontinuityTime |
TimeStamp |
|
Defined Values
| mvpnMIB |
1.3.6.1.2.1.243 |
| This MIB module contains managed object definitions to
configure and/or monitor Multicast communication over IP
Virtual Private Networks (VPNs) supported by the
Multiprotocol Label Switching/Border Gateway Protocol
(MPLS/BGP) on a Provider Edge (PE) router.
Copyright (c) 2018 IETF Trust and the persons identified
as authors of the code. All rights reserved.
Redistribution and use in source and binary forms, with or
without modification, is permitted pursuant to, and subject
to the license terms contained in, the Simplified BSD License
set forth in Section 4.c of the IETF Trust's Legal Provisions
Relating to IETF Documents
(http://trustee.ietf.org/license-info).
|
| MODULE-IDENTITY |
|
|
|
| mvpnMvrfs |
1.3.6.1.2.1.243.1.1.1 |
| The total number of Multicast Virtual Routing and
Forwarding (MVRF) tables that are present on
this Provider Edge (PE) router. This includes MVRFs
for IPv4, IPv6, and Multipoint LDP (mLDP) C-multicast.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| mvpnV4Mvrfs |
1.3.6.1.2.1.243.1.1.2 |
| The number of MVRFs for IPv4 C-multicast on this PE.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| mvpnV6Mvrfs |
1.3.6.1.2.1.243.1.1.3 |
| The number of MVRFs for IPv6 C-multicast on this PE.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| mvpnMldpMvrfs |
1.3.6.1.2.1.243.1.1.4 |
| The number of MVRFs on this PE that use BGP for
exchanging mLDP C-multicast routing information.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| mvpnPimV4Mvrfs |
1.3.6.1.2.1.243.1.1.5 |
| The number of MVRFs on this PE that use Provider
Independent Multicast (PIM) for exchanging IPv4
C-multicast routing information.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| mvpnPimV6Mvrfs |
1.3.6.1.2.1.243.1.1.6 |
| The number of MVRFs on this PE that use PIM for
exchanging IPv6 C-multicast routing information.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| mvpnBgpV4Mvrfs |
1.3.6.1.2.1.243.1.1.7 |
| The number of MVRFs on this PE that use BGP for
exchanging IPv4 C-multicast routing information.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| mvpnBgpV6Mvrfs |
1.3.6.1.2.1.243.1.1.8 |
| The number of MVRFs on this PE that use BGP for
exchanging IPv6 C-multicast routing information.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Gauge32 |
|
|
| mvpnSPTunnelLimit |
1.3.6.1.2.1.243.1.1.9 |
| The maximum number of selective provider tunnels that
are allowed for a particular MVPN on this PE.
|
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
1..4294967295 |
|
| mvpnBgpSrcSharedTreeJoinTimer |
1.3.6.1.2.1.243.1.1.11 |
| A configurable timer to control the delay
of Source/Shared Tree Join C-multicast route
advertisements.
|
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| mvpnGenericTable |
1.3.6.1.2.1.243.1.2 |
| A conceptual table containing generic information about
MVPNs on this PE.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
MvpnGenericEntry |
|
| mvpnGenericEntry |
1.3.6.1.2.1.243.1.2.1 |
| A conceptual row that represents an MVPN on this PE.
The MVPN represented by this entry will have one or more
corresponding P-Multicast Service Interfaces (PMSIs)
and a corresponding VRF in MPLS-L3VPN-STD-MIB (RFC 4382).
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
MvpnGenericEntry |
|
|
| mvpnGenMvrfLastAction |
1.3.6.1.2.1.243.1.2.1.2 |
| This object describes the last action pertaining
to the MVPN represented by this entry.
The enumerated action types and the corresponding
descriptions are as follows:
createdMvrf:
MVRF was created for this MVPN on the PE.
deletedMvrf:
MVRF for this MVPN was deleted from the PE.
A conceptual row in this table will never have
mvpnGenMvrfLastAction equal to deletedMvrf,
because in that case, the row itself will not exist
in the table.
This value for mvpnGenMvrfLastAction is defined
solely for use in the mvpnMvrfActionChange
notification.
modifiedMvrfIpmsiConfig:
An I-PMSI for this MVPN was configured, deleted,
or changed.
modifiedMvrfSpmsiConfig:
An S-PMSI for this MVPN was configured, deleted,
or changed.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
createdMvrf(1), deletedMvrf(2), modifiedMvrfIpmsiConfig(3), modifiedMvrfSpmsiConfig(4) |
|
| mvpnGenMvrfLastActionTime |
1.3.6.1.2.1.243.1.2.1.3 |
| The timestamp when the last action, given in
the corresponding mvpnGenMvrfLastAction object,
was carried out.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DateAndTime |
|
|
| mvpnGenMvrfCreationTime |
1.3.6.1.2.1.243.1.2.1.4 |
| The timestamp when the MVRF was created for
the MVPN represented by this entry.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DateAndTime |
|
|
| mvpnGenCmcastRouteProtocol |
1.3.6.1.2.1.243.1.2.1.5 |
| The protocol used to signal C-multicast routing
information across the provider core for the MVPN
represented by this entry.
The enumerated protocols and the corresponding
descriptions are as follows:
pim : PIM (PIM-MVPN)
bgp : BGP (BGP-MVPN)
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
pim(1), bgp(2) |
|
| mvpnGenIpmsiInfo |
1.3.6.1.2.1.243.1.2.1.6 |
| A pointer to a conceptual row representing
the corresponding I-PMSI in mvpnPmsiTable.
If there is no I-PMSI for the MVPN
represented by this entry, the
value of this object will be zeroDotZero.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
RowPointer |
|
|
| mvpnGenInterAsPmsiInfo |
1.3.6.1.2.1.243.1.2.1.7 |
| A pointer to a conceptual row representing
the corresponding segmented Inter-AS I-PMSI in mvpnPmsiTable.
If there is no segmented Inter-AS I-PMSI for the MVPN,
the value of this object will be zeroDotZero.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
RowPointer |
|
|
| mvpnGenUmhSelection |
1.3.6.1.2.1.243.1.2.1.8 |
| The Upstream Multicast Hop (UMH) selection method for the
MVPN represented by this entry.
The enumerated methods and the corresponding
descriptions are as follows:
highestPeAddress : PE with the highest address
(see RFC 6513, Section 5.1.3)
cRootGroupHashing : hashing based on (c-root, c-group)
ucastUmhRoute : per-unicast route towards c-root
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
highestPeAddress(1), cRootGroupHashing(2), ucastUmhRoute(3) |
|
| mvpnGenCustomerSiteType |
1.3.6.1.2.1.243.1.2.1.9 |
| The type of the customer site, connected to
the MVPN represented by this entry.
The enumerated types and the corresponding
descriptions are as follows:
senderReceiver : Site is both sender and receiver
receiverOnly : Site is receiver only
senderOnly : Site is sender only
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
senderReceiver(1), receiverOnly(2), senderOnly(3) |
|
| mvpnBgpTable |
1.3.6.1.2.1.243.1.3 |
| A conceptual table that supplements mvpnGenericTable
with BGP-MVPN-specific information for BGP-MVPNs on this PE.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
MvpnBgpEntry |
|
| mvpnBgpEntry |
1.3.6.1.2.1.243.1.3.1 |
| A conceptual row corresponding to a BGP-MVPN on this PE.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
MvpnBgpEntry |
|
|
| mvpnBgpMode |
1.3.6.1.2.1.243.1.3.1.1 |
| The inter-site C-tree mode used by the BGP-MVPN
represented by this entry.
other : none of the following
rptSpt : inter-site shared tree mode
(Rendezvous Point Tree (RPT) and
source-specific shortest-path tree (SPT))
sptOnly : inter-site source-only tree mode
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
other(0), rptSpt(1), sptOnly(2) |
|
| mvpnBgpMsgRateLimit |
1.3.6.1.2.1.243.1.3.1.4 |
| The configurable upper bound for the rate of the BGP
C-multicast routing information message exchange between
this PE and other PEs in the BGP-MVPN corresponding to
this entry.
|
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..4294967295 |
|
| mvpnBgpMaxSpmsiAdRoutes |
1.3.6.1.2.1.243.1.3.1.5 |
| The configurable upper bound for the number of S-PMSI
auto-discovery (A-D) routes for the BGP-MVPN
corresponding to this entry.
|
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..4294967295 |
|
| mvpnBgpMaxSpmsiAdRouteFreq |
1.3.6.1.2.1.243.1.3.1.6 |
| The configurable upper bound for the frequency of
S-PMSI A-D route generation for the BGP-MVPN
corresponding to this entry.
|
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..4294967295 |
|
| mvpnBgpMaxSrcActiveAdRoutes |
1.3.6.1.2.1.243.1.3.1.7 |
| The configurable upper bound for the number of
Source Active A-D routes for the BGP-MVPN corresponding
to this entry.
|
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..4294967295 |
|
| mvpnBgpMaxSrcActiveAdRouteFreq |
1.3.6.1.2.1.243.1.3.1.8 |
| The configurable upper bound for the frequency of Source
Active A-D route generation for the BGP-MVPN corresponding
to this entry.
|
| Status: current |
Access: read-write |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..4294967295 |
|
| mvpnPmsiTable |
1.3.6.1.2.1.243.1.4 |
| A conceptual table containing information related
to PMSIs on this PE.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
MvpnPmsiEntry |
|
| mvpnPmsiEntry |
1.3.6.1.2.1.243.1.4.1 |
| A conceptual row corresponding to a
PMSI on this PE.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
MvpnPmsiEntry |
|
|
| mvpnPmsiTunnelIfIndex |
1.3.6.1.2.1.243.1.4.1.1 |
| A unique value for this conceptual row. Its value
will be the same as that of the ifIndex object instance
for the corresponding PMSI in ifTable.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InterfaceIndex |
|
|
| mvpnPmsiTunnelAttribute |
1.3.6.1.2.1.243.1.4.1.5 |
| A pointer to a conceptual row representing
the P-tunnel used by the PMSI in
l2L3VpnMcastPmsiTunnelAttributeTable.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
RowPointer |
|
|
| mvpnPmsiTunnelPimGroupAddrType |
1.3.6.1.2.1.243.1.4.1.6 |
| The InetAddressType of the mvpnPmsiTunnelPimGroupAddr object
that follows. When the PMSI corresponding to this entry
does not use the PIM provider tunnel, i.e., the value of
mvpnPmsiTunnelType is not one of pimSsm(3), pimAsm(4), or
pimBidir(5), this object should be unknown(0).
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
InetAddressType |
|
|
| mvpnPmsiTunnelPimGroupAddr |
1.3.6.1.2.1.243.1.4.1.7 |
| The tunnel address that is used by the PMSI
corresponding to this entry. When the PMSI
corresponding to this entry does not use
the PIM provider tunnel, i.e., the value of
mvpnPmsiTunnelType is not one of pimSsm(3),
pimAsm(4), or pimBidir(5), this
object should be a zero-length octet string.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
InetAddress |
|
|
| mvpnPmsiEncapsulationType |
1.3.6.1.2.1.243.1.4.1.8 |
| The encapsulation type used for sending
packets through the PMSI corresponding to this entry.
The enumerated encapsulation types and the corresponding
descriptions are as follows:
greIp : Generic Routing Encapsulation (GRE)
(RFC 2784)
ipIp : IP-in-IP encapsulation (RFC 2003)
mpls : MPLS encapsulation (RFC 3032)
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
greIp(1), ipIp(2), mpls(3) |
|
| mvpnSpmsiTable |
1.3.6.1.2.1.243.1.5 |
| A conceptual table containing information related
to S-PMSIs on this PE.
This table stores only S-PMSI-specific attribute
information. Generic PMSI attribute information of
S-PMSIs is stored in mvpnPmsiTable.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
MvpnSpmsiEntry |
|
| mvpnSpmsiEntry |
1.3.6.1.2.1.243.1.5.1 |
| A conceptual row corresponding to an S-PMSI on this PE.
Implementers need to be aware that if the total number of
octets in mplsL3VpnVrfName, mvpnSpmsiCmcastGroupAddr, and
mvpnSpmsiCmcastSourceAddr exceeds 113, the OIDs of column
instances in this row will have more than 128 sub-identifiers
and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
MvpnSpmsiEntry |
|
|
| mvpnSpmsiCmcastGroupAddr |
1.3.6.1.2.1.243.1.5.1.2 |
| The group address of the C-flow assigned to the
S-PMSI corresponding to this entry.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InetAddress |
|
|
| mvpnSpmsiCmcastSourceAddr |
1.3.6.1.2.1.243.1.5.1.5 |
| The source address of the C-flow assigned to the
S-PMSI corresponding to this entry.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InetAddress |
|
|
| mvpnSpmsiPmsiPointer |
1.3.6.1.2.1.243.1.5.1.7 |
| A pointer to a conceptual row representing
generic information of this S-PMSI in mvpnPmsiTable.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
RowPointer |
|
|
| mvpnAdvtStatsTable |
1.3.6.1.2.1.243.1.6 |
| A conceptual table containing statistics pertaining to
I-PMSI and S-PMSI advertisements sent/received by this PE.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
MvpnAdvtStatsEntry |
|
| mvpnAdvtStatsEntry |
1.3.6.1.2.1.243.1.6.1 |
| A conceptual row corresponding to statistics
pertaining to advertisements sent/received
for a particular MVPN on this PE.
Implementers need to be aware that if the total number of
octets in mplsL3VpnVrfName and mvpnAdvtPeerAddr exceeds 115,
then OIDs of column instances in this row will have more than
128 sub-identifiers and cannot be accessed using SNMPv1,
SNMPv2c, or SNMPv3.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
MvpnAdvtStatsEntry |
|
|
| mvpnAdvtType |
1.3.6.1.2.1.243.1.6.1.1 |
| The PMSI type.
The enumerated PMSI types and corresponding
descriptions are as follows:
intraAsIpmsi : Intra-AS Inclusive PMSI
interAsIpmsi : Inter-AS Inclusive PMSI
sPmsi : Selective PMSI
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
intraAsIpmsi(0), interAsIpmsi(1), sPmsi(2) |
|
| mvpnAdvtPeerAddrType |
1.3.6.1.2.1.243.1.6.1.2 |
| The InternetAddressType of the mvpnAdvtPeerAddr object
that follows.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InetAddressType |
|
|
| mvpnAdvtPeerAddr |
1.3.6.1.2.1.243.1.6.1.3 |
| The address of a peer PE that exchanges advertisement with
this PE.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InetAddress |
|
|
| mvpnAdvtSent |
1.3.6.1.2.1.243.1.6.1.4 |
| The number of advertisements successfully
sent to the peer PE specified by the corresponding
mvpnAdvtPeerAddr.
Discontinuities in the value of this counter can
occur at re-initialization of the management system
and at other times as indicated by the corresponding
mvpnAdvtCounterDiscontinuityTime object.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| mvpnAdvtReceived |
1.3.6.1.2.1.243.1.6.1.5 |
| The number of advertisements received from the peer PE
specified by the corresponding mvpnAdvtPeerAddr object.
This includes advertisements that were discarded.
Discontinuities in the value of this counter can
occur at re-initialization of the management system
and at other times as indicated by the corresponding
mvpnAdvtCounterDiscontinuityTime object.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| mvpnAdvtReceivedError |
1.3.6.1.2.1.243.1.6.1.6 |
| The total number of advertisements received from a peer PE,
specified by the corresponding mvpnAdvtPeerAddr object,
that were rejected due to an error(s) in the advertisement.
The value of this object includes
the error cases counted in the corresponding
mvpnAdvtReceivedMalformedTunnelType and
mvpnAdvtReceivedMalformedTunnelId objects.
Discontinuities in the value of this counter can
occur at re-initialization of the management system
and at other times as indicated by the corresponding
mvpnAdvtCounterDiscontinuityTime object.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter32 |
|
|
| mvpnAdvtLastSentTime |
1.3.6.1.2.1.243.1.6.1.9 |
| The timestamp when the last advertisement
was successfully sent by this PE. If no
advertisement has been sent since the
last re-initialization of this PE, this
object will have a zero-length string.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DateAndTime |
|
|
| mvpnAdvtLastReceivedTime |
1.3.6.1.2.1.243.1.6.1.10 |
| The timestamp when the last advertisement
was successfully received from the peer PE specified
by the corresponding mvpnAdvtPeerAddr object and
processed by this PE.
If no advertisement has been received since the
last re-initialization of this PE, this object
will have a zero-length string.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
DateAndTime |
|
|
| mvpnAdvtCounterDiscontinuityTime |
1.3.6.1.2.1.243.1.6.1.11 |
| The value of sysUpTime on the most recent occasion
at which any one or more of this application's
counters, viz., counters with the OID prefix
'mvpnAdvtSent', 'mvpnAdvtReceived',
'mvpnAdvtReceivedError',
'mvpnAdvtReceivedMalformedTunnelType', or
'mvpnAdvtReceivedMalformedTunnelId', suffered a
discontinuity.
If no such discontinuities have occurred since the
last re-initialization of the local management
subsystem, this object will have a zero value.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TimeStamp |
|
|
| mvpnMrouteTable |
1.3.6.1.2.1.243.1.7 |
| A conceptual table containing multicast routing information
corresponding to the MVRFs present on the PE.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
MvpnMrouteEntry |
|
| mvpnMrouteEntry |
1.3.6.1.2.1.243.1.7.1 |
| A conceptual row corresponding to a route for IP datagrams
from a particular source and addressed to a particular
IP multicast group address.
Implementers need to be aware that if the total number of
octets in mplsL3VpnVrfName, mvpnMrouteCmcastGroupAddr, and
mvpnMrouteCmcastSourceAddrs exceeds 113, the OIDs of column
instances in this row will have more than 128 sub-identifiers
and cannot be accessed using SNMPv1, SNMPv2c, or SNMPv3.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
MvpnMrouteEntry |
|
|
| mvpnMrouteCmcastGroupAddr |
1.3.6.1.2.1.243.1.7.1.2 |
| The IP multicast group address that, along with
the corresponding mvpnMrouteCmcastGroupPrefixLength object,
identifies destinations for which this entry contains
multicast routing information.
This address object is only significant up to
mvpnMrouteCmcastGroupPrefixLength bits. The remaining
address bits MUST be set to zero.
For addresses of type 'ipv4z' or 'ipv6z', the appended zone
index is significant even though it lies beyond the prefix
length. The use of these address types indicates that this
forwarding state applies only within the given zone. Zone
index zero is not valid in this table.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InetAddress |
|
|
| mvpnMrouteCmcastGroupPrefixLength |
1.3.6.1.2.1.243.1.7.1.3 |
| The length in bits of the mask that, along with
the corresponding mvpnMrouteCmcastGroupAddr object,
identifies destinations for which this entry contains
multicast routing information.
If the corresponding InetAddressType is 'ipv4' or 'ipv4z',
this object must be in the range 4..32.
If the corresponding InetAddressType is 'ipv6' or 'ipv6z',
this object must be in the range 8..128.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InetAddressPrefixLength |
|
|
| mvpnMrouteCmcastSourceAddrType |
1.3.6.1.2.1.243.1.7.1.4 |
| The InetAddressType of the mvpnMrouteCmcastSourceAddrs object
that follows.
A value of unknown(0) indicates a non-source-specific entry,
corresponding to all sources in the group. Otherwise, the
value MUST be the same as the value of
mvpnMrouteCmcastGroupAddrType.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InetAddressType |
|
|
| mvpnMrouteCmcastSourceAddrs |
1.3.6.1.2.1.243.1.7.1.5 |
| The network address that, along with the
corresponding mvpnMrouteCmcastSourcePrefixLength object,
identifies the sources for which this entry contains
multicast routing information.
This address object is only significant up to
mvpnMrouteCmcastSourcePrefixLength bits.
The remaining address bits MUST be set to zero.
For addresses of type 'ipv4z' or 'ipv6z', the appended zone
index is significant even though it lies beyond the prefix
length. The use of these address types indicates that this
source address applies only within the given zone. Zone
index zero is not valid in this table.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InetAddress |
|
|
| mvpnMrouteCmcastSourcePrefixLength |
1.3.6.1.2.1.243.1.7.1.6 |
| The length in bits of the mask that, along with
the corresponding mvpnMrouteCmcastSourceAddr object,
identifies the sources for which this entry contains
multicast routing information.
If the corresponding InetAddressType is 'ipv4' or 'ipv4z',
this object must be in the range 4..32.
If the corresponding InetAddressType is 'ipv6' or 'ipv6z',
this object must be in the range 8..128.
If the corresponding InetAddressType is 'unknown',
this object must be zero.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InetAddressPrefixLength |
|
|
| mvpnMrouteUpstreamNeighborAddrType |
1.3.6.1.2.1.243.1.7.1.7 |
| The InetAddressType of the mvpnMrouteUpstreamNeighborAddr
object that follows.
A value of unknown(0) indicates that the upstream
neighbor is unknown, for example, in
Bidirectional PIM (BIDIR-PIM).
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
InetAddressType |
|
|
| mvpnMrouteUpstreamNeighborAddr |
1.3.6.1.2.1.243.1.7.1.8 |
| The address of the upstream neighbor (for example,
the Reverse Path Forwarding (RPF) neighbor) from
which IP datagrams from these sources represented
by this entry to this multicast address are received.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
InetAddress |
|
|
| mvpnMrouteInIfIndex |
1.3.6.1.2.1.243.1.7.1.9 |
| The value of ifIndex for the interface on which IP
datagrams sent by these sources represented by this entry to
this multicast address are received.
A value of zero indicates that datagrams are not
subject to an incoming interface check but may be accepted
on multiple interfaces (for example, in BIDIR-PIM).
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
InterfaceIndexOrZero |
|
|
| mvpnMrouteExpiryTime |
1.3.6.1.2.1.243.1.7.1.10 |
| The minimum amount of time remaining before this entry will
be aged out. The value zero indicates that the entry is not
subject to aging. If the corresponding mvpnMrouteNextHopState
object is pruned(1), this object represents the remaining
time for the prune to expire after which the state will
return to forwarding(2).
If the corresponding mvpnMrouteNextHopState object is
forwarding(2), this object indicates the time after which
this entry will be removed from the table.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TimeTicks |
|
|
| mvpnMrouteProtocol |
1.3.6.1.2.1.243.1.7.1.11 |
| The multicast routing protocol via which this multicast
forwarding entry was learned.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
IANAipMRouteProtocol |
|
|
| mvpnMrouteRtProtocol |
1.3.6.1.2.1.243.1.7.1.12 |
| The routing protocol via which the route used to find the
upstream or parent interface for this multicast forwarding
entry was learned.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
IANAipRouteProtocol |
|
|
| mvpnMrouteRtAddr |
1.3.6.1.2.1.243.1.7.1.14 |
| The address portion of the route used to find the upstream
or parent interface for this multicast forwarding entry.
This address object is only significant up to
mvpnMrouteRtPrefixLength bits. The remaining address bits
MUST be set to zero.
For addresses of type 'ipv4z' or 'ipv6z', the appended zone
index is significant even though it lies beyond the prefix
length. The use of these address types indicates that this
forwarding state applies only within the given zone. Zone
index zero is not valid in this table.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
InetAddress |
|
|
| mvpnMrouteRtPrefixLength |
1.3.6.1.2.1.243.1.7.1.15 |
| The length in bits of the mask associated with the route
used to find the upstream or parent interface for this
multicast forwarding entry.
If the corresponding InetAddressType is 'ipv4' or 'ipv4z',
this object must be in the range 4..32.
If the corresponding InetAddressType is 'ipv6' or 'ipv6z',
this object must be in the range 8..128.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
InetAddressPrefixLength |
|
|
| mvpnMrouteRtType |
1.3.6.1.2.1.243.1.7.1.16 |
| The reason for placing the route in the (logical)
multicast Routing Information Base (RIB).
The enumerated reasons and the corresponding
descriptions are as follows:
unicast:
The route would normally be placed only in
the unicast RIB, but it was placed in the multicast
RIB by local configuration, such as when running
PIM over RIP.
multicast:
The route was explicitly added to the multicast RIB by
the routing protocol, such as the Distance Vector
Multicast Routing Protocol (DVMRP) or Multiprotocol BGP.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
unicast(1), multicast(2) |
|
| mvpnMrouteOctets |
1.3.6.1.2.1.243.1.7.1.17 |
| The number of octets contained in IP datagrams that were
received from sources represented by this entry and
addressed to this multicast group address and that were
forwarded by this router.
Discontinuities in the value of this counter can
occur at re-initialization of the management system
and at other times as indicated by the corresponding
mvpnMrouteCounterDiscontinuityTime object.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter64 |
|
|
| mvpnMroutePkts |
1.3.6.1.2.1.243.1.7.1.18 |
| The number of packets routed using this multicast route
entry.
Discontinuities in the value of this counter can
occur at re-initialization of the management system
and at other times as indicated by the corresponding
mvpnMrouteCounterDiscontinuityTime object.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter64 |
|
|
| mvpnMrouteTtlDroppedOctets |
1.3.6.1.2.1.243.1.7.1.19 |
| The number of octets contained in IP datagrams that this
router has received from sources represented by
this entry and addressed to this multicast group address,
which were dropped due to Time To Live (TTL) issues.
TTL issues occur when the TTL (IPv4) or Hop Limit (IPv6)
of the incoming packet was decremented to zero or to a
value less than ipMcastInterfaceTtl of the corresponding
interface.
The ipMcastInterfaceTtl object is defined in IPMCAST-MIB
(RFC 5132) and represents the datagram TTL
threshold for the interface. Any IP multicast datagrams
with a TTL (IPv4) or Hop Limit (IPv6) less than this
threshold will not be forwarded out of the interface.
The default value of zero means all multicast packets are
forwarded out of the interface. A value of 256 means that
no multicast packets are forwarded out of the interface.
Discontinuities in the value of this counter can
occur at re-initialization of the management system
and at other times as indicated by the corresponding
mvpnMrouteCounterDiscontinuityTime object.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter64 |
|
|
| mvpnMrouteTtlDroppedPackets |
1.3.6.1.2.1.243.1.7.1.20 |
| The number of packets that this router has received from
the sources represented by this entry and addressed to this
multicast group address, which were dropped due to
Time To Live (TTL) issues. TTL issues occur when the
TTL (IPv4) or Hop Limit (IPv6) of the incoming packet was
decremented to zero or to a value less than
ipMcastInterfaceTtl of the corresponding interface.
The ipMcastInterfaceTtl object is defined in IPMCAST-MIB
(RFC 5132) and represents the datagram TTL
threshold for the interface. Any IP multicast datagrams
with a TTL (IPv4) or Hop Limit (IPv6) less than this
threshold will not be forwarded out of the interface.
The default value of zero means all multicast packets are
forwarded out of the interface. A value of 256 means that
no multicast packets are forwarded out of the interface.
Discontinuities in the value of this counter can
occur at re-initialization of the management system
and at other times as indicated by the corresponding
mvpnMrouteCounterDiscontinuityTime object.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter64 |
|
|
| mvpnMrouteDroppedInOctets |
1.3.6.1.2.1.243.1.7.1.21 |
| The number of octets contained in IP datagrams that this
router has received from sources represented by
this entry and addressed to this multicast group address,
which were dropped due to an error(s).
The value of this object includes the octets counted
in the corresponding mvpnMrouteTtlDroppedOctets object.
Discontinuities in the value of this counter can
occur at re-initialization of the management system
and at other times as indicated by the corresponding
mvpnMrouteCounterDiscontinuityTime object.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter64 |
|
|
| mvpnMrouteDroppedInPackets |
1.3.6.1.2.1.243.1.7.1.22 |
| The number of packets that this router has received from
sources represented by this entry and addressed to this
multicast group address, which were dropped due to an
error(s). The value of this object includes the number
of octets counted in the corresponding
mvpnMrouteTtlDroppedPackets object.
Discontinuities in the value of this counter can
occur at re-initialization of the management system
and at other times as indicated by the corresponding
mvpnMrouteCounterDiscontinuityTime object.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter64 |
|
|
| mvpnMroutePmsiPointer |
1.3.6.1.2.1.243.1.7.1.23 |
| A pointer to a conceptual row representing
the corresponding I-PMSI in mvpnPmsiTable or S-PMSI
in mvpnSpmsiTable that this C-multicast route is using.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
RowPointer |
|
|
| mvpnMrouteNumberOfLocalReplication |
1.3.6.1.2.1.243.1.7.1.24 |
| Number of replications for local receivers.
For example, if an ingress PE needs to send traffic out of
N PE-CE interfaces, then mvpnMrouteNumberOfLocalReplication
is N.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| mvpnMrouteNumberOfRemoteReplication |
1.3.6.1.2.1.243.1.7.1.25 |
| Number of local replications for remote PEs. For example,
if the number of remote PEs that need to receive traffic is N,
then mvpnMrouteNumberOfRemoteReplication is N in case of
Ingress Replication, but it may be less than N in case of
RSVP-TE or mLDP Point-to-Multipoint (P2MP) tunnels, depending
on the actual number of replications the PE needs to do.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
|
|
| mvpnMrouteCounterDiscontinuityTime |
1.3.6.1.2.1.243.1.7.1.26 |
| The value of sysUpTime on the most recent occasion
at which any one or more of this application's
counters, viz., counters with the OID prefix
'mvpnMrouteOctets', 'mvpnMroutePkts',
'mvpnMrouteTtlDroppedOctets',
'mvpnMrouteTtlDroppedPackets',
'mvpnMrouteDroppedInOctets', or 'mvpnMrouteDroppedInPackets',
suffered a discontinuity.
If no such discontinuities have occurred since the
last re-initialization of the local management
subsystem, this object will have a zero value.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TimeStamp |
|
|
| mvpnMrouteNextHopTable |
1.3.6.1.2.1.243.1.8 |
| A conceptual table containing information on the
next hops for routing IP multicast datagrams.
Each entry is one of a list of next hops for
a set of sources sending to a multicast group
address.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
SEQUENCE OF |
|
|
| |
|
MvpnMrouteNextHopEntry |
|
| mvpnMrouteNextHopEntry |
1.3.6.1.2.1.243.1.8.1 |
| A conceptual row corresponding to a next hop to which
IP multicast datagrams from a set of sources to
an IP multicast group address are routed.
Implementers need to be aware that if the total number of
octets in mplsL3VpnVrfName, mvpnMrouteNextHopGroupAddr,
mvpnMrouteNextHopSourceAddrs, and mvpnMrouteNextHopAddr
exceeds 111, the OIDs of column instances in this row
will have more than 128 sub-identifiers and cannot be
accessed using SNMPv1, SNMPv2c, or SNMPv3.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
MvpnMrouteNextHopEntry |
|
|
| mvpnMrouteNextHopGroupAddr |
1.3.6.1.2.1.243.1.8.1.2 |
| The IP multicast group address that, along with
the corresponding mvpnMrouteNextHopGroupPrefixLength object,
identifies destinations for which this entry contains
multicast forwarding information.
This address object is only significant up to
mvpnMrouteNextHopGroupPrefixLength bits. The remaining
address bits MUST be set to zero.
For addresses of type 'ipv4z' or 'ipv6z', the appended zone
index is significant even though it lies beyond the prefix
length. The use of these address types indicates that this
forwarding state applies only within the given zone. Zone
index zero is not valid in this table.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InetAddress |
|
|
| mvpnMrouteNextHopGroupPrefixLength |
1.3.6.1.2.1.243.1.8.1.3 |
| The length in bits of the mask that, along with
the corresponding mvpnMrouteGroupAddr object,
identifies destinations for which this entry contains
multicast routing information.
If the corresponding InetAddressType is 'ipv4' or 'ipv4z',
this object must be in the range 4..32.
If the corresponding InetAddressType is 'ipv6' or 'ipv6z',
this object must be in the range 8..128.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InetAddressPrefixLength |
|
|
| mvpnMrouteNextHopSourceAddrType |
1.3.6.1.2.1.243.1.8.1.4 |
| The InetAddressType of the mvpnMrouteNextHopSourceAddrs
object that follows.
A value of unknown(0) indicates a non-source-specific entry,
corresponding to all sources in the group. Otherwise, the
value MUST be the same as the value of
mvpnMrouteNextHopGroupAddrType.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InetAddressType |
|
|
| mvpnMrouteNextHopSourceAddrs |
1.3.6.1.2.1.243.1.8.1.5 |
| The network address that, along with the
corresponding mvpnMrouteNextHopSourcePrefixLength object,
identifies the sources for which this entry specifies
a next hop.
This address object is only significant up to
mvpnMrouteNextHopSourcePrefixLength bits. The remaining
address bits MUST be set to zero.
For addresses of type 'ipv4z' or 'ipv6z', the appended zone
index is significant even though it lies beyond the prefix
length. The use of these address types indicates that this
source address applies only within the given zone. Zone
index zero is not valid in this table.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InetAddress |
|
|
| mvpnMrouteNextHopSourcePrefixLength |
1.3.6.1.2.1.243.1.8.1.6 |
| The length in bits of the mask that, along with
the corresponding mvpnMrouteNextHopSourceAddrs object,
identifies the sources for which this entry specifies
a next hop.
If the corresponding InetAddressType is 'ipv4' or 'ipv4z',
this object must be in the range 4..32.
If the corresponding InetAddressType is 'ipv6' or 'ipv6z',
this object must be in the range 8..128.
If the corresponding InetAddressType is 'unknown',
this object must be zero.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InetAddressPrefixLength |
|
|
| mvpnMrouteNextHopAddr |
1.3.6.1.2.1.243.1.8.1.9 |
| The address of the next hop specific to this entry. For
most interfaces, this is identical to
mvpnMrouteNextHopGroupAddr. Non-Broadcast Multi-Access
(NBMA) interfaces, however, may have multiple next-hop
addresses out of a single outgoing interface.
|
| Status: current |
Access: not-accessible |
| OBJECT-TYPE |
|
|
|
| |
InetAddress |
|
|
| mvpnMrouteNextHopState |
1.3.6.1.2.1.243.1.8.1.10 |
| An indication of whether the outgoing interface and next
hop represented by this entry is currently being used to
forward IP datagrams.
The enumerated states and the corresponding
descriptions are as follows:
pruned : this entry is not currently being used.
forwarding : this entry is currently being used.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
INTEGER |
pruned(1), forwarding(2) |
|
| mvpnMrouteNextHopExpiryTime |
1.3.6.1.2.1.243.1.8.1.11 |
| The minimum amount of time remaining before this entry will
be aged out. If mvpnMrouteNextHopState is pruned(1),
this object represents the remaining time for the prune
to expire after which the state will return to forwarding(2).
If mvpnMrouteNextHopState is forwarding(2),
this object indicates the time after which this
entry will be removed from the table.
The value of zero indicates that the entry is not subject to
aging.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TimeTicks |
|
|
| mvpnMrouteNextHopClosestMemberHops |
1.3.6.1.2.1.243.1.8.1.12 |
| The minimum number of hops between this router and any
member of this IP multicast group reached via this next hop
on the corresponding outgoing interface. Any IP multicast
datagram for the group that has a TTL (IPv4) or a Hop Count
(IPv6) less than mvpnMrouteNextHopClosestMemberHops will
not be forwarded through this interface.
A value of zero means all multicast datagrams are forwarded
out of the interface. A value of 256 means that no multicast
datagrams are forwarded out of the interface.
This is an optimization applied by multicast routing
protocols that explicitly track hop counts to downstream
listeners. Multicast protocols that are not aware of hop
counts to downstream listeners set this object to zero.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Unsigned32 |
0..256 |
|
| mvpnMrouteNextHopOctets |
1.3.6.1.2.1.243.1.8.1.14 |
| The number of octets of multicast packets that have been
forwarded using this route.
Discontinuities in the value of this counter can
occur at re-initialization of the management system
and at other times as indicated by the corresponding
mvpnMrouteNextHopCounterDiscontinuityTime object.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter64 |
|
|
| mvpnMrouteNextHopPkts |
1.3.6.1.2.1.243.1.8.1.15 |
| The number of packets that have been forwarded using this
route.
Discontinuities in the value of this counter can
occur at re-initialization of the management system
and at other times as indicated by the corresponding
mvpnMrouteNextHopCounterDiscontinuityTime object.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
Counter64 |
|
|
| mvpnMrouteNextHopCounterDiscontinuityTime |
1.3.6.1.2.1.243.1.8.1.16 |
| The value of sysUpTime on the most recent occasion
at which any one or more of this application's
counters, viz., counters with the OID prefix
'mvpnMrouteNextHopOctets' or 'mvpnMrouteNextHopPackets',
suffered a discontinuity.
If no such discontinuities have occurred since the
last re-initialization of the local management
subsystem, this object will have a zero value.
|
| Status: current |
Access: read-only |
| OBJECT-TYPE |
|
|
|
| |
TimeStamp |
|
|
| mvpnMvrfActionTaken |
1.3.6.1.2.1.243.0.1 |
| mvpnMvrfActionTaken notifies about a change
in an MVRF on the PE. The change itself will be given by
mvpnGenMvrfLastAction.
|
| Status: current |
Access: read-only |
| NOTIFICATION-TYPE |
|
|
|
| mvpnModuleFullCompliance |
1.3.6.1.2.1.243.2.2.1 |
| Compliance statement for agents that provide full support
for BGP-MPLS-LAYER3-VPN-MULTICAST-MIB.
|
| Status: current |
Access: read-only |
| MODULE-COMPLIANCE |
|
|
|
| mvpnModuleReadOnlyCompliance |
1.3.6.1.2.1.243.2.2.2 |
| Compliance requirement for implementations that
only provide read-only support for
BGP-MPLS-LAYER3-VPN-MULTICAST-MIB. Such devices
can then be monitored but cannot be configured
using this MIB module.
|
| Status: current |
Access: read-only |
| MODULE-COMPLIANCE |
|
|
|
| mvpnModuleAdvtStatsCompliance |
1.3.6.1.2.1.243.2.2.3 |
| Compliance statement for agents that support
the monitoring of the statistics pertaining
to advertisements sent/received by a PE.
|
| Status: current |
Access: read-only |
| MODULE-COMPLIANCE |
|
|
|
| mvpnScalarGroup |
1.3.6.1.2.1.243.2.1.1 |
| These objects are used to monitor/manage
global statistics and parameters.
|
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| mvpnBgpScalarGroup |
1.3.6.1.2.1.243.2.1.2 |
| These objects are used to monitor/manage
BGP-MVPN-specific global parameters.
|
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| mvpnGenericGroup |
1.3.6.1.2.1.243.2.1.3 |
| These objects are used to monitor MVPNs on a PE.
|
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| mvpnBgpGroup |
1.3.6.1.2.1.243.2.1.4 |
| These objects are used to monitor/manage
MVPN-wise BGP-specific parameters.
|
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| mvpnPmsiGroup |
1.3.6.1.2.1.243.2.1.5 |
| These objects are used to monitor
I-PMSI and S-PMSI tunnels on a PE.
|
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| mvpnAdvtStatsGroup |
1.3.6.1.2.1.243.2.1.6 |
| These objects are used to monitor
the statistics pertaining to I-PMSI and S-PMSI
advertisements sent/received by a PE.
|
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| mvpnMrouteGroup |
1.3.6.1.2.1.243.2.1.7 |
| These objects are used to monitor multicast routing
information corresponding to the MVRFs on a PE.
|
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| mvpnMrouteNextHopGroup |
1.3.6.1.2.1.243.2.1.8 |
| These objects are used to monitor the information on
next hops for routing datagrams to MVPNs on a PE.
|
| Status: current |
Access: read-only |
| OBJECT-GROUP |
|
|
|
| mvpnNotificationGroup |
1.3.6.1.2.1.243.2.1.9 |
| Objects required for MVPN notifications. |
| Status: current |
Access: read-only |
| NOTIFICATION-GROUP |
|
|
|