BAY-STACK-EAPOL-EXTENSION-MIB

File: BAY-STACK-EAPOL-EXTENSION-MIB.mib (53327 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC IF-MIB
Q-BRIDGE-MIB SYNOPTICS-ROOT-MIB SNMP-FRAMEWORK-MIB

Imported symbols

OBJECT-TYPE MODULE-IDENTITY Integer32
TimeTicks TruthValue MacAddress
RowStatus InterfaceIndex VlanId
VlanIdOrNone VlanIdOrAny bayStackMibs
SnmpAdminString

Defined Types

BseePortConfigEntry  
SEQUENCE    
  bseePortConfigPortNumber InterfaceIndex
  bseePortConfigGuestVlanId VlanIdOrNone
  bseePortConfigMultiHostEnabled TruthValue
  bseePortConfigMultiHostEapMaxNumMacs Integer32
  bseePortConfigMultiHostAllowNonEapClient TruthValue
  bseePortConfigMultiHostNonEapMacSource INTEGER
  bseePortConfigMultiHostNonEapMaxNumMacs Integer32
  bseePortConfigGuestVlanEnabled TruthValue
  bseePortConfigMultiHostRadiusAuthNonEapClient TruthValue
  bseePortConfigMultiHostSingleAuthEnabled TruthValue
  bseePortConfigMultiHostAllowNonEapPhones TruthValue
  bseePortConfigMultiHostAllowRadiusAssignedVlan TruthValue
  bseePortConfigMultiHostEapPacketMode INTEGER
  bseePortConfigMultiHostEapRadiusTimeoutMode INTEGER
  bseePortConfigMultiHostAllowNonEapRadiusAssignedVlan TruthValue
  bseePortConfigProcessRadiusRequestsServerPackets TruthValue
  bseePortConfigEapProtocolEnabled TruthValue
  bseePortConfigMultiHostUseMostRecentRadiusAssignedVlan TruthValue
  bseePortConfigMultiHostClearNeap MacAddress
  bseePortConfigMultiHostBlockDifferentVlanAuth TruthValue
  bseePortConfigMultiHostAdacNonEapEnabled TruthValue
  bseePortConfigDefaultEapAll TruthValue
  bseePortConfigMultiHostMaxMacs Integer32

BseeMultiHostStatusEntry  
SEQUENCE    
  bseeMultiHostStatusPortNumber InterfaceIndex
  bseeMultiHostStatusClientMACAddr MacAddress
  bseeMultiHostStatusPaeState INTEGER
  bseeMultiHostStatusBackendAuthState INTEGER
  bseeMultiHostStatusReauthenticate INTEGER
  bseeMultiHostStatusVid VlanIdOrAny
  bseeMultiHostStatusPri Integer32

BseeMultiHostSessionStatsEntry  
SEQUENCE    
  bseeMultiHostSessionStatsPortNumber InterfaceIndex
  bseeMultiHostSessionStatsClientMACAddr MacAddress
  bseeMultiHostSessionId SnmpAdminString
  bseeMultiHostSessionAuthenticMethod INTEGER
  bseeMultiHostSessionTime TimeTicks
  bseeMultiHostSessionTerminateCause INTEGER
  bseeMultiHostSessionUserName SnmpAdminString

BseeMultiHostNonEapMacEntry  
SEQUENCE    
  bseeMultiHostNonEapMacPortNumber InterfaceIndex
  bseeMultiHostNonEapMacClientMACAddr MacAddress
  bseeMultiHostNonEapMacRowStatus RowStatus

BseeMultiHostNonEapStatusEntry  
SEQUENCE    
  bseeMultiHostNonEapStatusPortNumber InterfaceIndex
  bseeMultiHostNonEapStatusClientMACAddr MacAddress
  bseeMultiHostNonEapStatusState INTEGER
  bseeMultiHostNonEapStatusReauthenticate INTEGER
  bseeMultiHostNonEapStatusVid VlanIdOrAny
  bseeMultiHostNonEapStatusPri Integer32

BseeSupplicantUserEntry  
SEQUENCE    
  bseeSupplicantPortNumber InterfaceIndex
  bseeSupplicantUserName SnmpAdminString
  bseeSupplicantPassword SnmpAdminString
  bseeSupplicantUserState INTEGER

BseeMultiHostVoipVlanEntry  
SEQUENCE    
  bseeMultiHostVoipVlanIndex Integer32
  bseeMultiHostVoipVlanId VlanId
  bseeMultiHostVoipVlanEnabled TruthValue

BseeMultiHostDhcpAuthPhoneEntry  
SEQUENCE    
  bseeMultiHostDhcpAuthPhonePortNumber InterfaceIndex
  bseeMultiHostDhcpAuthPhoneClientMACAddr MacAddress
  bseeMultiHostDhcpAuthPhoneUserName SnmpAdminString

Defined Values

bayStackEapExtMib 1.3.6.1.4.1.45.5.3
BayStack EAPOL Extension MIB Copyright 2003-2010 Avaya All rights reserved. This Avaya SNMP Management Information Base Specification (Specification) embodies Avaya's confidential and proprietary intellectual property. Avaya retains all title and ownership in the Specification, including any revisions. This Specification is supplied 'AS IS,' and Avaya makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
MODULE-IDENTITY    

bseeNotifications 1.3.6.1.4.1.45.5.3.2
OBJECT IDENTIFIER    

bseeNotifications0 1.3.6.1.4.1.45.5.3.2.0
OBJECT IDENTIFIER    

bseeObjects 1.3.6.1.4.1.45.5.3.1
OBJECT IDENTIFIER    

bseeUserBasedPoliciesEnabled 1.3.6.1.4.1.45.5.3.1.1
This object indicates whether EAPOL User-based policies are enabled or disabled.
OBJECT-TYPE    
  TruthValue  

bseeGuestVlanId 1.3.6.1.4.1.45.5.3.1.2
This object specifies the ID of the global default guest VLAN. This VLAN is used for ports which do not have a configured guest VLAN. Access to the guest VLAN is allowed for MAC addresses before EAP authentication has been performed. However, if the value of bseeGuestVlanEnabled is false(2), then access to the guest VLAN is not allowed for ports that do not have a configured guest VLAN.
OBJECT-TYPE    
  VlanId  

bseeRemediationVlanId 1.3.6.1.4.1.45.5.3.1.3
This object specifies the ID of the remediation VLAN. If EAP authentication fails for a port, MAC addresses on that port are restricted to access only the remediation VLAN. However, if the value of bseeRemediationVlanEnabled is false(2), then access is not allowed at all for a port when EAP authentication fails.
OBJECT-TYPE    
  VlanId  

bseeMaximumEapClientMacs 1.3.6.1.4.1.45.5.3.1.4
This object specifies the global maximum number of EAP authenticated MAC addresses allowed.
OBJECT-TYPE    
  Integer32 1..800  

bseeMaximumNonEapClientMacs 1.3.6.1.4.1.45.5.3.1.5
This object specifies the global maximum number of non-EAP authenticated MAC addresses allowed.
OBJECT-TYPE    
  Integer32 1..800  

bseeGuestVlanEnabled 1.3.6.1.4.1.45.5.3.1.6
This object specifies whether access to the global default guest VLAN is allowed.
OBJECT-TYPE    
  TruthValue  

bseeRemediationVlanEnabled 1.3.6.1.4.1.45.5.3.1.7
This object specifies whether access to the remediation VLAN is allowed.
OBJECT-TYPE    
  TruthValue  

bseeMultiHostAllowNonEapClient 1.3.6.1.4.1.45.5.3.1.8
This object controls whether non-EAP clients (MAC addresses) are allowed. This is the system-wide setting. The associated per-port setting (bseePortConfigMultiHostAllowNonEapClient) must also be true for non-EAP clients to be allowed on a particular port.
OBJECT-TYPE    
  TruthValue  

bseeMultiHostRadiusAuthNonEapClient 1.3.6.1.4.1.45.5.3.1.9
This object controls whether non-EAP clients (MAC addresses) may be authenticated using RADIUS. This is the system-wide setting. The associated per-port setting (bseePortConfigMultiHostRadiusAuthNonEapClient) must also be true for non-EAP clients to be authenticated using RADIUS on a particular port.
OBJECT-TYPE    
  TruthValue  

bseeMultiHostSingleAuthEnabled 1.3.6.1.4.1.45.5.3.1.10
This object controls whether non-EAP clients (MAC addresses) may be automatically authenticated on a port after an EAP client has been authenticated (known as MHSA). This is the system-wide setting. The associated per-port setting must also be true for non-EAP clients to be authenticated in this way.
OBJECT-TYPE    
  TruthValue  

bseeUserBasedPoliciesFilterOnMac 1.3.6.1.4.1.45.5.3.1.11
This object indicates whether the EAPOL User-based policy filters that are installed on ports will be dynamically modified to include the MAC address for which the filters are installed.
OBJECT-TYPE    
  TruthValue  

bseeMultiHostNonEapUserBasedPoliciesEnabled 1.3.6.1.4.1.45.5.3.1.12
This object indicates whether non-EAPOL User-based policies are enabled or disabled.
OBJECT-TYPE    
  TruthValue  

bseeMultiHostNonEapUserBasedPoliciesFilterOnMac 1.3.6.1.4.1.45.5.3.1.13
This object indicates whether the non-EAPOL User-based policy filters that are installed on ports will be dynamically modified to include the MAC address for which the filters are installed.
OBJECT-TYPE    
  TruthValue  

bseeMultihostNonEapRadiusPasswordAttributeFormat 1.3.6.1.4.1.45.5.3.1.14
This object controls the format of the RADIUS password attribute that is included in requests to the RADIUS server for authenticating non-EAP clients (MAC addresses). If the ipAddr(0) bit is set, the password attribute will contain the switch's IP address encoded as a string of four 3-digit 0-padded integers. For example, the encoding for the IP address 47.80.225.1 would be '047080225001'. If the macAddr(1) bit is set, the password attribute will contain the MAC address to be authenticated as a string of six 2-digit hex numbers. For example, the MAC address 00:08:01:0a:33:34 would be encoded as '0008010a3334'. If the portNumber(2) bit is set, the password attribute will contain the port number on which the MAC address was seen, encoded as a string of two 2-digit 0-padded integers. The first integer is the unit/slot number, and the second number is the port number on that unit/slot. For a standalone stackable unit, the unit/slot number will be 0. For example, the encoding for unit/port 1/23 would be '0123', and the encoding for port 7 on a standalone stackable unit would be '0007'. If the key(3) bit is set, the password attribute will contain a custom configured string of up to 32 characters in length. If padding(4) bit is set, the password will contain dots even if fields in the password are blank. For instance, IP and Key will be represented as IP...Key. If the bit is not set, there will be dots only to separate fields. IP and Key will be IP.Key, while IP, Mac, Port or Key alone will be as they are, with no dots. The fields in the password attribute will appear in the order of the bits defined in this object, i.e., IP addr, followed by MAC addr, followed by port number, and finally by the key. Fields are separated by a '.' character. The separators are present regardless of whether a field is present if padding is used. So, for example, if all four fields are present, the password attribute might contain: 047080225001.0008010a3334.0123.ERS4000isGreat If none of the three fields are present, the password attribute will be '...' with padding used, or '' with no padding.
OBJECT-TYPE    
  BITS ipAddr(0), macAddr(1), portNumber(2), key(3), padding(4)  

bseeMultiHostAllowNonEapPhones 1.3.6.1.4.1.45.5.3.1.15
This object indicates whether IP phones will be allowed access based on DHCP.
OBJECT-TYPE    
  TruthValue  

bseeMultiHostAllowRadiusAssignedVlan 1.3.6.1.4.1.45.5.3.1.16
This object indicates whether to allow the use of RADIUS-assigned VLANs in multihost-eap mode.
OBJECT-TYPE    
  TruthValue  

bseeMultiHostEapPacketMode 1.3.6.1.4.1.45.5.3.1.17
This object indicates whether to use unicast or multicast packets for Eap-ReqId packets. Normally, multicast packets are used.
OBJECT-TYPE    
  INTEGER multicast(1), unicast(2)  

bseeMultiHostEapRadiusTimeoutMode 1.3.6.1.4.1.45.5.3.1.18
This object indicates whether or not to fail authentication of EAP users on a RADIUS timeout.
OBJECT-TYPE    
  INTEGER fail(1), doNotFail(2)  

bseeMultiHostAllowNonEapRadiusAssignedVlan 1.3.6.1.4.1.45.5.3.1.19
This object indicates whether to allow the use of RADIUS-assigned VLANs in multihost-eap mode for non-EAP clients.
OBJECT-TYPE    
  TruthValue  

bseeMultiHostEapProtocolEnabled 1.3.6.1.4.1.45.5.3.1.20
This object controls whether processing of EAP protocol packets is enabled.
OBJECT-TYPE    
  TruthValue  

bseeMultiHostUseMostRecentRadiusAssignedVlan 1.3.6.1.4.1.45.5.3.1.21
Controls whether to use most recent RADIUS-assigned VLAN.
OBJECT-TYPE    
  TruthValue  

bseeMultiHostFailOpenVlanId 1.3.6.1.4.1.45.5.3.1.22
This object specifies the ID of the global fail-over Vlan.
OBJECT-TYPE    
  VlanId  

bseeMultiHostFailOpenVlanEnabled 1.3.6.1.4.1.45.5.3.1.23
This object specifies whether to use the fail-over Vlan.
OBJECT-TYPE    
  TruthValue  

bseeMultiHostMultiVlan 1.3.6.1.4.1.45.5.3.1.24
This object specifies whether to use the multi-VLAN functionality with MHMA mode.
OBJECT-TYPE    
  TruthValue  

bseeMultiHostNeapReauthenticationEnabled 1.3.6.1.4.1.45.5.3.1.25
This object specifies whether to use 'NEAP re-authentication' feature
OBJECT-TYPE    
  TruthValue  

bseeMultiHostBlockDifferentVlanAuth 1.3.6.1.4.1.45.5.3.1.26
This object specifies whether to block authentication of clients which have an associated RADIUS assigned VLAN with an invalid value or different from first client authenticated on the same port
OBJECT-TYPE    
  TruthValue  

bseeMultiHostAdacDummyRadiusRequests 1.3.6.1.4.1.45.5.3.1.27
This object specifies whether to send or not dummy RADIUS requests for NEAP users authenticated as ADAC NEAP
OBJECT-TYPE    
  TruthValue  

bseeAllowPortMirroringOnEap 1.3.6.1.4.1.45.5.3.1.28
This object specifies whether EAP enabled ports can be involved in port mirroring
OBJECT-TYPE    
  TruthValue  

bseeMultiHostAdacNonEapEnabled 1.3.6.1.4.1.45.5.3.1.29
This object specifies whether the authentication of Non-EAP phones using ADAC is allowed.
OBJECT-TYPE    
  TruthValue  

bseeMultiHostFailOpenVlanContinuityModeEnabled 1.3.6.1.4.1.45.5.3.1.30
This object specifies whether to use the fail-over Vlan continuity mode.
OBJECT-TYPE    
  TruthValue  

bseeMultiHostNonEapRadiusPasswordFreeformKey 1.3.6.1.4.1.45.5.3.1.31
This command specifies a custom string to be put in the password used to authenticate Non-EAP clients via RADIUS server.
OBJECT-TYPE    
  OCTET STRING Size(0..32)  

bseeMultiHostFailOpenVlanDisableEapMode 1.3.6.1.4.1.45.5.3.1.32
This object specifies whether to use the Fail Open VLAN Disable EAP Mode.
OBJECT-TYPE    
  TruthValue  

bseePaeSystemOperState 1.3.6.1.4.1.45.5.3.1.33
The oper state of EAP when ports are in Fail Open VLAN Disable EAP Mode.
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

bseeDefaultEapAll 1.3.6.1.4.1.45.5.3.1.34
This object specifies whether to default all global EAP settings.
OBJECT-TYPE    
  TruthValue  

bseePortConfigTable 1.3.6.1.4.1.45.5.3.3
This table is used to control the EAP multihost configuration for each port in the system.
OBJECT-TYPE    
  SEQUENCE OF  
    BseePortConfigEntry

bseePortConfigEntry 1.3.6.1.4.1.45.5.3.3.1
The EAP multihost configuration for a port.
OBJECT-TYPE    
  BseePortConfigEntry  

bseePortConfigPortNumber 1.3.6.1.4.1.45.5.3.3.1.1
The Port number associated with this Port.
OBJECT-TYPE    
  InterfaceIndex  

bseePortConfigGuestVlanId 1.3.6.1.4.1.45.5.3.3.1.2
This object specifies the ID of the guest VLAN for this port. Access to the guest VLAN is allowed for MAC addresses before EAP authentication has been performed. If the value of this object is 0, then the global guest VLAN ID is used for this port, as specified in bseeGuestVlanId. However, if the value of the associated instance of bseePortConfigGuestVlanEnabled is false(2), then access to the guest VLAN is not allowed for the port, regardless of the value of bseePortConfigGuestVlanId.
OBJECT-TYPE    
  VlanIdOrNone  

bseePortConfigMultiHostEnabled 1.3.6.1.4.1.45.5.3.3.1.3
This object controls whether EAP multihost is enabled for a port.
OBJECT-TYPE    
  TruthValue  

bseePortConfigMultiHostEapMaxNumMacs 1.3.6.1.4.1.45.5.3.3.1.4
This object specifies the maximum number of EAP-authentication MAC addresses allowed on this port. A value of 0 indicates that there is no port-specific limit.
OBJECT-TYPE    
  Integer32 0..100  

bseePortConfigMultiHostAllowNonEapClient 1.3.6.1.4.1.45.5.3.3.1.5
This object controls whether non-EAP clients (MAC addresses) are allowed on the port.
OBJECT-TYPE    
  TruthValue  

bseePortConfigMultiHostNonEapMacSource 1.3.6.1.4.1.45.5.3.3.1.6
This object controls the source for finding allowed non-EAP MAC addresses.
OBJECT-TYPE    
  INTEGER autoLearn(1), userConfig(2), radius(3)  

bseePortConfigMultiHostNonEapMaxNumMacs 1.3.6.1.4.1.45.5.3.3.1.7
This object specifies the maximum number of non-EAP authenticated MAC addresses allowed on this port.
OBJECT-TYPE    
  Integer32 1..100  

bseePortConfigGuestVlanEnabled 1.3.6.1.4.1.45.5.3.3.1.8
This object controls whether access to the guest VLAN is allowed for a port.
OBJECT-TYPE    
  TruthValue  

bseePortConfigMultiHostRadiusAuthNonEapClient 1.3.6.1.4.1.45.5.3.3.1.9
This object controls whether non-EAP clients (MAC addresses) may authenticated using RADIUS on the port.
OBJECT-TYPE    
  TruthValue  

bseePortConfigMultiHostSingleAuthEnabled 1.3.6.1.4.1.45.5.3.3.1.10
This object controls whether non-EAP clients (MAC addresses) may be automatically authenticated on the port after an EAP client has been authenticated (known as MHSA).
OBJECT-TYPE    
  TruthValue  

bseePortConfigMultiHostAllowNonEapPhones 1.3.6.1.4.1.45.5.3.3.1.11
This object indicates whether IP phones will be allowed access based on DHCP.
OBJECT-TYPE    
  TruthValue  

bseePortConfigMultiHostAllowRadiusAssignedVlan 1.3.6.1.4.1.45.5.3.3.1.12
This object indicates whether to allow the use of RADIUS-assigned VLANs in multihost-eap mode.
OBJECT-TYPE    
  TruthValue  

bseePortConfigMultiHostEapPacketMode 1.3.6.1.4.1.45.5.3.3.1.13
This object indicates whether to use unicast or multicast packets for Eap-ReqId packets. Normally, multicast packets are used.
OBJECT-TYPE    
  INTEGER multicast(1), unicast(2)  

bseePortConfigMultiHostEapRadiusTimeoutMode 1.3.6.1.4.1.45.5.3.3.1.14
This object indicates whether or not to fail authentication of EAP users on a RADIUS timeout.
OBJECT-TYPE    
  INTEGER fail(1), doNotFail(2)  

bseePortConfigMultiHostAllowNonEapRadiusAssignedVlan 1.3.6.1.4.1.45.5.3.3.1.15
This object indicates whether to allow the use of RADIUS-assigned VLANs in multihost-eap mode for non-EAP clients.
OBJECT-TYPE    
  TruthValue  

bseePortConfigProcessRadiusRequestsServerPackets 1.3.6.1.4.1.45.5.3.3.1.16
This object indicates whether to process any RADIUS requests-server packets that are received on this port.
OBJECT-TYPE    
  TruthValue  

bseePortConfigEapProtocolEnabled 1.3.6.1.4.1.45.5.3.3.1.17
This object controls whether EAP protocol packets are processed on this port.
OBJECT-TYPE    
  TruthValue  

bseePortConfigMultiHostUseMostRecentRadiusAssignedVlan 1.3.6.1.4.1.45.5.3.3.1.18
Controls whether to use most recent RADIUS-assigned VLAN.
OBJECT-TYPE    
  TruthValue  

bseePortConfigMultiHostClearNeap 1.3.6.1.4.1.45.5.3.3.1.19
Setting this object will clear NEAP authenticated clients from the authentication list. If the value is set to 00:00:00:00:00:00, all clients will be cleared from this port. Otherwise, only a specific client will be cleared.
OBJECT-TYPE    
  MacAddress  

bseePortConfigMultiHostBlockDifferentVlanAuth 1.3.6.1.4.1.45.5.3.3.1.20
Controls whether to block authentication of clients which have an associated RADIUS assigned VLAN with an invalid value or different from first client authenticated on the same port.
OBJECT-TYPE    
  TruthValue  

bseePortConfigMultiHostAdacNonEapEnabled 1.3.6.1.4.1.45.5.3.3.1.21
This object specifies whether the authentication of Non-EAP phones using ADAC is allowed on this port.
OBJECT-TYPE    
  TruthValue  

bseePortConfigDefaultEapAll 1.3.6.1.4.1.45.5.3.3.1.22
This object specifies whether to default all EAP settings on this port.
OBJECT-TYPE    
  TruthValue  

bseePortConfigMultiHostMaxMacs 1.3.6.1.4.1.45.5.3.3.1.23
This object specifies the maximum number of EAP and NEAP clients allowed on this port.
OBJECT-TYPE    
  Integer32 0..100  

bseeMultiHostStatusTable 1.3.6.1.4.1.45.5.3.4
This table provides the EAP authentication status per-MAC address per-port.
OBJECT-TYPE    
  SEQUENCE OF  
    BseeMultiHostStatusEntry

bseeMultiHostStatusEntry 1.3.6.1.4.1.45.5.3.4.1
The status of EAP authentication of clients for a port.
OBJECT-TYPE    
  BseeMultiHostStatusEntry  

bseeMultiHostStatusPortNumber 1.3.6.1.4.1.45.5.3.4.1.1
The Port number associated with this client.
OBJECT-TYPE    
  InterfaceIndex  

bseeMultiHostStatusClientMACAddr 1.3.6.1.4.1.45.5.3.4.1.2
The MAC address of the client.
OBJECT-TYPE    
  MacAddress  

bseeMultiHostStatusPaeState 1.3.6.1.4.1.45.5.3.4.1.3
The current value of the Authenticator PAE state machine.
OBJECT-TYPE    
  INTEGER initialize(1), disconnected(2), connecting(3), authenticating(4), authenticated(5), aborting(6), held(7), forceAuth(8), forceUnauth(9)  

bseeMultiHostStatusBackendAuthState 1.3.6.1.4.1.45.5.3.4.1.4
The current state of the Backend Authentication state machine.
OBJECT-TYPE    
  INTEGER request(1), response(2), success(3), fail(4), timeout(5), idle(6), initialize(7)  

bseeMultiHostStatusReauthenticate 1.3.6.1.4.1.45.5.3.4.1.5
Setting this object to reauthenticate(2) will force the client to be reauthenticated. When retrieved, the value of this object is always other(1).
OBJECT-TYPE    
  INTEGER other(1), reauthenticate(2)  

bseeMultiHostStatusVid 1.3.6.1.4.1.45.5.3.4.1.6
The Vlan ID associated with this client for MultiVlan capabilities. If MultiVlan is not enabled for this client, the value of this object will be 4095.
OBJECT-TYPE    
  VlanIdOrAny  

bseeMultiHostStatusPri 1.3.6.1.4.1.45.5.3.4.1.7
The Vlan priority value associated with this client for MultiVlan capabilities. If MultiVlan is not enabled for this client, the value of this object will be 8.
OBJECT-TYPE    
  Integer32 0..8  

bseeMultiHostSessionStatsTable 1.3.6.1.4.1.45.5.3.5
A table that contains the session statistics objects for the Authenticator PAE associated with each EAP client on each Port. An entry appears in this table for each client MAC address on each port that may authenticate access to itself.
OBJECT-TYPE    
  SEQUENCE OF  
    BseeMultiHostSessionStatsEntry

bseeMultiHostSessionStatsEntry 1.3.6.1.4.1.45.5.3.5.1
The session statistics information for an Authenticator PAE. This shows the current values being collected for each session that is still in progress, or the final values for the last valid session for each client where there is no session currently active. This is similar to the dot1xAuthSessionStatsTable, except that it provides information per-port-per-MAC, rather than just per-port.
OBJECT-TYPE    
  BseeMultiHostSessionStatsEntry  

bseeMultiHostSessionStatsPortNumber 1.3.6.1.4.1.45.5.3.5.1.1
The Port number associated with this client.
OBJECT-TYPE    
  InterfaceIndex  

bseeMultiHostSessionStatsClientMACAddr 1.3.6.1.4.1.45.5.3.5.1.2
The MAC address of this client.
OBJECT-TYPE    
  MacAddress  

bseeMultiHostSessionId 1.3.6.1.4.1.45.5.3.5.1.3
A unique identifier for the session, in the form of a printable ASCII string of at least three characters.
OBJECT-TYPE    
  SnmpAdminString  

bseeMultiHostSessionAuthenticMethod 1.3.6.1.4.1.45.5.3.5.1.4
The authentication method used to establish the session.
OBJECT-TYPE    
  INTEGER remoteAuthServer(1), localAuthServer(2)  

bseeMultiHostSessionTime 1.3.6.1.4.1.45.5.3.5.1.5
The duration of the session in seconds.
OBJECT-TYPE    
  TimeTicks  

bseeMultiHostSessionTerminateCause 1.3.6.1.4.1.45.5.3.5.1.6
The reason for the session termination.
OBJECT-TYPE    
  INTEGER supplicantLogoff(1), portFailure(2), supplicantRestart(3), reauthFailed(4), authControlForceUnauth(5), portReInit(6), portAdminDisabled(7), notTerminatedYet(999)  

bseeMultiHostSessionUserName 1.3.6.1.4.1.45.5.3.5.1.7
The User-Name representing the identity of the Supplicant PAE.
OBJECT-TYPE    
  SnmpAdminString  

bseeMultiHostNonEapMacTable 1.3.6.1.4.1.45.5.3.6
A table that contains the non-EAP MAC addresses that are allowed access to EAP-enabled interfaces.
OBJECT-TYPE    
  SEQUENCE OF  
    BseeMultiHostNonEapMacEntry

bseeMultiHostNonEapMacEntry 1.3.6.1.4.1.45.5.3.6.1
An allowed non-EAP MAC address.
OBJECT-TYPE    
  BseeMultiHostNonEapMacEntry  

bseeMultiHostNonEapMacPortNumber 1.3.6.1.4.1.45.5.3.6.1.1
The Port number on which the MAC address is allowed.
OBJECT-TYPE    
  InterfaceIndex  

bseeMultiHostNonEapMacClientMACAddr 1.3.6.1.4.1.45.5.3.6.1.2
The MAC address allowed on the port.
OBJECT-TYPE    
  MacAddress  

bseeMultiHostNonEapMacRowStatus 1.3.6.1.4.1.45.5.3.6.1.3
This is used to control creation/deletion of entries in this table.
OBJECT-TYPE    
  RowStatus  

bseeMultiHostNonEapStatusTable 1.3.6.1.4.1.45.5.3.7
This table provides the authentication status of non-EAP clients per-MAC address per-port.
OBJECT-TYPE    
  SEQUENCE OF  
    BseeMultiHostNonEapStatusEntry

bseeMultiHostNonEapStatusEntry 1.3.6.1.4.1.45.5.3.7.1
The status of authentication of a non-EAP client for a port.
OBJECT-TYPE    
  BseeMultiHostNonEapStatusEntry  

bseeMultiHostNonEapStatusPortNumber 1.3.6.1.4.1.45.5.3.7.1.1
The Port number associated with this client.
OBJECT-TYPE    
  InterfaceIndex  

bseeMultiHostNonEapStatusClientMACAddr 1.3.6.1.4.1.45.5.3.7.1.2
The MAC address of the client.
OBJECT-TYPE    
  MacAddress  

bseeMultiHostNonEapStatusState 1.3.6.1.4.1.45.5.3.7.1.3
The authentication status. Values are: rejected(1) - the MAC address could not be authenticated on this port locallyAuthenticated(2) - the MAC address was authenticated using the local table of allowed clients radiusPending(3) - the MAC address is awaiting authentication by a RADIUS server radiusAuthenticated(4) - the MAC address was authenticated by a RADIUS server adacAuthenticated(5) - the MAC address was authenticated using ADAC configuration tables mhsaAuthenticated(6) - the MAC address was auto-authenticated on a port following a successful authentication of an EAP client
OBJECT-TYPE    
  INTEGER rejected(1), locallyAuthenticated(2), radiusPending(3), radiusAuthenticated(4), adacAuthenticated(5), mhsaAuthenticated(6)  

bseeMultiHostNonEapStatusReauthenticate 1.3.6.1.4.1.45.5.3.7.1.4
Setting this object to reauthenticate(2) will force the MAC address to be reauthenticated. When retrieved, the value of this object is always other(1).
OBJECT-TYPE    
  INTEGER other(1), reauthenticate(2)  

bseeMultiHostNonEapStatusVid 1.3.6.1.4.1.45.5.3.7.1.5
The Vlan ID associated with this client for MultiVlan capabilities. If MultiVlan is not enabled for this client, the value of this object will be 4095.
OBJECT-TYPE    
  VlanIdOrAny  

bseeMultiHostNonEapStatusPri 1.3.6.1.4.1.45.5.3.7.1.6
The Vlan priority value associated with this client for MultiVlan capabilities. If MultiVlan is not enabled for this client, the value of this object will be 8.
OBJECT-TYPE    
  Integer32 0..8  

bseeSupplicantObjects 1.3.6.1.4.1.45.5.3.8
OBJECT IDENTIFIER    

bseeSupplicantEnabled 1.3.6.1.4.1.45.5.3.8.1
Indicates whether supplicant functionality is enabled or disabled. A value of true(1) means enabled.
OBJECT-TYPE    
  TruthValue  

bseeSupplicantUserTable 1.3.6.1.4.1.45.5.3.9
A table that contains the user name and password for the Supplicant PAE associated with each port. An entry appears in this table for each port that may authenticate itself when challenged by a remote system.
OBJECT-TYPE    
  SEQUENCE OF  
    BseeSupplicantUserEntry

bseeSupplicantUserEntry 1.3.6.1.4.1.45.5.3.9.1
The configuration information for a Supplicant PAE.
OBJECT-TYPE    
  BseeSupplicantUserEntry  

bseeSupplicantPortNumber 1.3.6.1.4.1.45.5.3.9.1.1
A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
OBJECT-TYPE    
  InterfaceIndex  

bseeSupplicantUserName 1.3.6.1.4.1.45.5.3.9.1.2
The user name currently in use by the Supplicant PAE state machine.
OBJECT-TYPE    
  SnmpAdminString Size(0..15)  

bseeSupplicantPassword 1.3.6.1.4.1.45.5.3.9.1.3
The password currently in use by the Supplicant PAE state machine.
OBJECT-TYPE    
  SnmpAdminString Size(0..15)  

bseeSupplicantUserState 1.3.6.1.4.1.45.5.3.9.1.4
Input the user state to logoff.
OBJECT-TYPE    
  INTEGER inactive(1), active(2), logoff(3)  

bseeMultiHostVoipVlanTable 1.3.6.1.4.1.45.5.3.10
A table that contains EAP VoIP Vlan settings.
OBJECT-TYPE    
  SEQUENCE OF  
    BseeMultiHostVoipVlanEntry

bseeMultiHostVoipVlanEntry 1.3.6.1.4.1.45.5.3.10.1
The configuration information for an EAP VoIP Vlan.
OBJECT-TYPE    
  BseeMultiHostVoipVlanEntry  

bseeMultiHostVoipVlanIndex 1.3.6.1.4.1.45.5.3.10.1.1
A unique identifier for each entry.
OBJECT-TYPE    
  Integer32 1..5  

bseeMultiHostVoipVlanId 1.3.6.1.4.1.45.5.3.10.1.2
This object specifies the Vlan ID of the VoIP Vlan.
OBJECT-TYPE    
  VlanId  

bseeMultiHostVoipVlanEnabled 1.3.6.1.4.1.45.5.3.10.1.3
This object specifies whether to use this VoIP Vlan.
OBJECT-TYPE    
  TruthValue  

bseeMultiHostDhcpAuthPhoneTable 1.3.6.1.4.1.45.5.3.11
This table provides the list of DHCP authenticated IP phones per-MAC address per-port.
OBJECT-TYPE    
  SEQUENCE OF  
    BseeMultiHostDhcpAuthPhoneEntry

bseeMultiHostDhcpAuthPhoneEntry 1.3.6.1.4.1.45.5.3.11.1
The DHCP authenticated IP phone for a port.
OBJECT-TYPE    
  BseeMultiHostDhcpAuthPhoneEntry  

bseeMultiHostDhcpAuthPhonePortNumber 1.3.6.1.4.1.45.5.3.11.1.1
The port number associated with the DHCP authenticated IP phone.
OBJECT-TYPE    
  InterfaceIndex  

bseeMultiHostDhcpAuthPhoneClientMACAddr 1.3.6.1.4.1.45.5.3.11.1.2
The MAC address of the DHCP authenticated IP phone.
OBJECT-TYPE    
  MacAddress  

bseeMultiHostDhcpAuthPhoneUserName 1.3.6.1.4.1.45.5.3.11.1.3
The user name currently in use by the DHCP authenticated IP phone.
OBJECT-TYPE    
  SnmpAdminString Size(0..32)