BAS-ALIAS-DOCS-IF-MIB

File: BAS-ALIAS-DOCS-IF-MIB.mib (28368 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
IF-MIB BAS-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Unsigned32
Integer32 Counter32 TimeTicks
IpAddress transmission TEXTUAL-CONVENTION
MacAddress RowStatus TruthValue
TimeInterval TimeStamp OBJECT-GROUP
MODULE-COMPLIANCE ifIndex basAliasDocsIf
BasChassisId BasSlotId BasInterfaceId
BasLogicalPortId

Defined Types

InterfaceIndexOrZero  
This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits the additional value of zero. the value zero is object-specific and must therefore be defined as part of the description of any object which uses this syntax. Examples of the usage of zero might include situations where interface was unknown, or when none or all interfaces need to be referenced.
TEXTUAL-CONVENTION    
  Integer32 0..2147483647  

TenthdBmV  
This data type represents power levels that are normally expressed in dBmV. Units are in tenths of a dBmV; for example, 5.1 dBmV will be represented as 51.
TEXTUAL-CONVENTION    
  Integer32  

TenthdB  
This data type represents power levels that are normally expressed in dB. Units are in tenths of a dB; for example, 5.1 dB will be represented as 51.
TEXTUAL-CONVENTION    
  Integer32  

BasDocsIfQosProfileEntry  
SEQUENCE    
  basDocsIfQosProfIndex Integer32
  basDocsIfQosProfPriority Integer32
  basDocsIfQosProfMaxUpBandwidth Integer32
  basDocsIfQosProfGuarUpBandwidth Integer32
  basDocsIfQosProfMaxDownBandwidth Integer32
  basDocsIfQosProfMaxTxBurst Integer32
  basDocsIfQosProfBaselinePrivacy TruthValue
  basDocsIfQosProfStatus RowStatus
  basDocsIfQosProfChassis BasChassisId
  basDocsIfQosProfSlot BasSlotId
  basDocsIfQosProfIf BasInterfaceId
  basDocsIfQosProfLPort BasLogicalPortId

BasDocsIfCmtsCmStatusEntry  
SEQUENCE    
  basDocsIfCmtsCmStatusIndex Integer32
  basDocsIfCmtsCmStatusMacAddress MacAddress
  basDocsIfCmtsCmStatusIpAddress IpAddress
  basDocsIfCmtsCmStatusDownChannelIfIndex InterfaceIndexOrZero
  basDocsIfCmtsCmStatusUpChannelIfIndex InterfaceIndexOrZero
  basDocsIfCmtsCmStatusRxPower TenthdBmV
  basDocsIfCmtsCmStatusTimingOffset Unsigned32
  basDocsIfCmtsCmStatusEqualizationData OCTET STRING
  basDocsIfCmtsCmStatusValue INTEGER
  basDocsIfCmtsCmStatusUnerroreds Counter32
  basDocsIfCmtsCmStatusCorrecteds Counter32
  basDocsIfCmtsCmStatusUncorrectables Counter32
  basDocsIfCmtsCmStatusSignalNoise TenthdB
  basDocsIfCmtsCmStatusMicroreflections Integer32
  basDocsIfCmtsCmStatusChassis BasChassisId
  basDocsIfCmtsCmStatusSlot BasSlotId
  basDocsIfCmtsCmStatusIf BasInterfaceId
  basDocsIfCmtsCmStatusLPort BasLogicalPortId

BasDocsIfCmtsQosProfileEntry  
SEQUENCE    
  basDocsIfCmtsQosProfilePermissions BITS
  basDocsIfCmtsQosProfileChassis BasChassisId
  basDocsIfCmtsQosProfileSlot BasSlotId
  basDocsIfCmtsQosProfileIf BasInterfaceId
  basDocsIfCmtsQosProfileLPort BasLogicalPortId

BasDocsIfCmtsMacToCmEntry  
SEQUENCE    
  basDocsIfCmtsCmMac MacAddress
  basDocsIfCmtsCmPtr Integer32
  basDocsIfCmtsCmChassis BasChassisId
  basDocsIfCmtsCmSlot BasSlotId
  basDocsIfCmtsCmIf BasInterfaceId
  basDocsIfCmtsCmLPort BasLogicalPortId

Defined Values

basAliasDocsIfMib 1.3.6.1.4.1.3493.2.7.8.1
This is the MIB Module for MCNS/DOCSIS compliant Radio Frequency (RF) interfaces in Cable Modems (CM) and Cable Modem Termination Systems (CMTS).
MODULE-IDENTITY    

basDocsIfMibObjects 1.3.6.1.4.1.3493.2.7.8.1.1
OBJECT IDENTIFIER    

basDocsIfBaseObjects 1.3.6.1.4.1.3493.2.7.8.1.1.1
OBJECT IDENTIFIER    

basDocsIfCmObjects 1.3.6.1.4.1.3493.2.7.8.1.1.2
OBJECT IDENTIFIER    

basDocsIfCmtsObjects 1.3.6.1.4.1.3493.2.7.8.1.1.3
OBJECT IDENTIFIER    

basDocsIfQosProfileTable 1.3.6.1.4.1.3493.2.7.8.1.1.1.3
Describes the attributes for each class of service.
OBJECT-TYPE    
  SEQUENCE OF  
    BasDocsIfQosProfileEntry

basDocsIfQosProfileEntry 1.3.6.1.4.1.3493.2.7.8.1.1.1.3.1
Describes the attributes for a single class of service. If implemented as read-create in the Cable Modem Termination System, creation of entries in this table is controlled by the value of docsIfCmtsQosProfilePermissions. If implemented as read-only, entries are created based on information in REG-REQ MAC messages received from Cable Modems (Cable Modem Termination System implementation), or based on information extracted from the TFTP option file (Cable Modem implementation). In the Cable Modem Termination system, read-only entries are removed if no longer referenced by docsIfCmtsServiceTable. An entry in this table must not be removed while it is referenced by an entry in docsIfCmServiceTable (Cable Modem) or docsIfCmtsServiceTable (Cable Modem Termination System). An entry in this table should not be changeable while it is referenced by an entry in docsIfCmtsServiceTable. If this table is created automatically, there should only be a single entry for each Class of Service. Multiple entries with the same Class of Service parameters are not recommended.
OBJECT-TYPE    
  BasDocsIfQosProfileEntry  

basDocsIfQosProfIndex 1.3.6.1.4.1.3493.2.7.8.1.1.1.3.1.1
The index value which uniquely identifies an entry in the docsIfQosProfileTable.
OBJECT-TYPE    
  Integer32 1..16383  

basDocsIfQosProfPriority 1.3.6.1.4.1.3493.2.7.8.1.1.1.3.1.2
A relative priority assigned to this service when allocating bandwidth. Zero indicates lowest priority; and seven indicates highest priority. Interpretation of priority is device-specific. MUST NOT be changed while this row is active.
OBJECT-TYPE    
  Integer32 0..7  

basDocsIfQosProfMaxUpBandwidth 1.3.6.1.4.1.3493.2.7.8.1.1.1.3.1.3
The maximum upstream bandwidth, in bits per second, allowed for a service with this service class. Zero if there is no restriction of upstream bandwidth. MUST NOT be changed while this row is active.
OBJECT-TYPE    
  Integer32 0..100000000  

basDocsIfQosProfGuarUpBandwidth 1.3.6.1.4.1.3493.2.7.8.1.1.1.3.1.4
Minimum guaranteed upstream bandwidth, in bits per second, allowed for a service with this service class. MUST NOT be changed while this row is active.
OBJECT-TYPE    
  Integer32 0..100000000  

basDocsIfQosProfMaxDownBandwidth 1.3.6.1.4.1.3493.2.7.8.1.1.1.3.1.5
The maximum downstream bandwidth, in bits per second, allowed for a service with this service class. Zero if there is no restriction of downstream bandwidth. MUST NOT be changed while this row is active.
OBJECT-TYPE    
  Integer32 0..100000000  

basDocsIfQosProfMaxTxBurst 1.3.6.1.4.1.3493.2.7.8.1.1.1.3.1.6
The maximum number of mini-slots that may be requested for a single upstream transmission. A value of zero means there is no limit. MUST NOT be changed while this row is active.
OBJECT-TYPE    
  Integer32 0..255  

basDocsIfQosProfBaselinePrivacy 1.3.6.1.4.1.3493.2.7.8.1.1.1.3.1.7
Indicates whether Baseline Privacy is enabled for this service class. MUST NOT be changed while this row is active.
OBJECT-TYPE    
  TruthValue  

basDocsIfQosProfStatus 1.3.6.1.4.1.3493.2.7.8.1.1.1.3.1.8
This is object is to used to create or delete rows in this table. This object MUST NOT be changed from active while the row is referenced by the any entry in either docsIfCmServiceTable (on the CM), or the docsIfCmtsServiceTable (on the CMTS).
OBJECT-TYPE    
  RowStatus  

basDocsIfQosProfChassis 1.3.6.1.4.1.3493.2.7.8.1.1.1.3.1.9
The BAS Chassis ID of this card.
OBJECT-TYPE    
  BasChassisId  

basDocsIfQosProfSlot 1.3.6.1.4.1.3493.2.7.8.1.1.1.3.1.10
The BAS Slot ID of this card.
OBJECT-TYPE    
  BasSlotId  

basDocsIfQosProfIf 1.3.6.1.4.1.3493.2.7.8.1.1.1.3.1.11
The BAS interface ID of this card.
OBJECT-TYPE    
  BasInterfaceId  

basDocsIfQosProfLPort 1.3.6.1.4.1.3493.2.7.8.1.1.1.3.1.12
The BAS logical port ID of this card.
OBJECT-TYPE    
  BasLogicalPortId  

basDocsIfCmtsCmStatusTable 1.3.6.1.4.1.3493.2.7.8.1.1.3.3
A set of objects in the CMTS, maintained for each Cable Modem connected to this CMTS.
OBJECT-TYPE    
  SEQUENCE OF  
    BasDocsIfCmtsCmStatusEntry

basDocsIfCmtsCmStatusEntry 1.3.6.1.4.1.3493.2.7.8.1.1.3.3.1
Status information for a single Cable Modem. An entry in this table exists for each Cable Modem that is connected to the CMTS implementing this table.
OBJECT-TYPE    
  BasDocsIfCmtsCmStatusEntry  

basDocsIfCmtsCmStatusIndex 1.3.6.1.4.1.3493.2.7.8.1.1.3.3.1.1
Index value to uniquely identify an entry in this table. For an individual Cable Modem, this index value should not change during CMTS uptime.
OBJECT-TYPE    
  Integer32 1..2147483647  

basDocsIfCmtsCmStatusMacAddress 1.3.6.1.4.1.3493.2.7.8.1.1.3.3.1.2
MAC address of this Cable Modem. If the Cable Modem has multiple MAC addresses, this is the MAC address associated with the Cable interface.
OBJECT-TYPE    
  MacAddress  

basDocsIfCmtsCmStatusIpAddress 1.3.6.1.4.1.3493.2.7.8.1.1.3.3.1.3
IP address of this Cable Modem. If the Cable Modem has no IP address assigned, or the IP address is unknown, this object returns a value of 0.0.0.0. If the Cable Modem has multiple IP addresses, this object returns the IP address associated with the Cable interface.
OBJECT-TYPE    
  IpAddress  

basDocsIfCmtsCmStatusDownChannelIfIndex 1.3.6.1.4.1.3493.2.7.8.1.1.3.3.1.4
IfIndex of the downstream channel this CM is connected to. If the downstream channel is unknown, this object returns a value of zero.
OBJECT-TYPE    
  InterfaceIndexOrZero  

basDocsIfCmtsCmStatusUpChannelIfIndex 1.3.6.1.4.1.3493.2.7.8.1.1.3.3.1.5
IfIndex of the upstream channel this CM is connected to. If the upstream channel is unknown, this object returns a value of zero.
OBJECT-TYPE    
  InterfaceIndexOrZero  

basDocsIfCmtsCmStatusRxPower 1.3.6.1.4.1.3493.2.7.8.1.1.3.3.1.6
The receive power as percieved for upstream data from this Cable Modem. If the receive power is unknown, this object returns a value of zero.
OBJECT-TYPE    
  TenthdBmV  

basDocsIfCmtsCmStatusTimingOffset 1.3.6.1.4.1.3493.2.7.8.1.1.3.3.1.7
A measure of the current round trip time for this CM. Used for timing of CM upstream transmissions to ensure synchronized arrivals at the CMTS. Units are in terms of (6.25 microseconds/64). Returns zero if the value is unknown.
OBJECT-TYPE    
  Unsigned32  

basDocsIfCmtsCmStatusEqualizationData 1.3.6.1.4.1.3493.2.7.8.1.1.3.3.1.8
Equalization data for this CM. Returns an empty string if the value is unknown or if there is no equalization data available or defined.
OBJECT-TYPE    
  OCTET STRING  

basDocsIfCmtsCmStatusValue 1.3.6.1.4.1.3493.2.7.8.1.1.3.3.1.9
Current Cable Modem connectivity state, as specified in the RF Interface Specification. Returned status information is the CM status as assumed by the CMTS, and indicates the following events: other(1) Any state other than below. ranging(2) The CMTS has received an Initial Ranging Request message from the CM, and the ranging process is not yet complete. rangingAborted(3) The CMTS has sent a Ranging Abort message to the CM. rangingComplete(4) The CMTS has sent a Ranging Complete message to the CM. ipComplete(5) The CMTS has received a DHCP reply message and forwarded it to the CM. registrationComplete(6) The CMTS has sent a Registration Response mesage to the CM. accessDenied(7) The CMTS has sent a Registration Aborted message to the CM. The CMTS only needs to report states it is able to detect.
OBJECT-TYPE    
  INTEGER other(1), ranging(2), rangingAborted(3), rangingComplete(4), ipComplete(5), registrationComplete(6), accessDenied(7)  

basDocsIfCmtsCmStatusUnerroreds 1.3.6.1.4.1.3493.2.7.8.1.1.3.3.1.10
Codewords received without error from this Cable Modem.
OBJECT-TYPE    
  Counter32  

basDocsIfCmtsCmStatusCorrecteds 1.3.6.1.4.1.3493.2.7.8.1.1.3.3.1.11
Codewords received with correctable errors from this Cable Modem.
OBJECT-TYPE    
  Counter32  

basDocsIfCmtsCmStatusUncorrectables 1.3.6.1.4.1.3493.2.7.8.1.1.3.3.1.12
Codewords received with uncorrectable errors from this Cable Modem.
OBJECT-TYPE    
  Counter32  

basDocsIfCmtsCmStatusSignalNoise 1.3.6.1.4.1.3493.2.7.8.1.1.3.3.1.13
Signal/Noise ratio as perceived for upstream data from this Cable Modem. If the Signal/Noise is unknown, this object returns a value of zero.
OBJECT-TYPE    
  TenthdB  

basDocsIfCmtsCmStatusMicroreflections 1.3.6.1.4.1.3493.2.7.8.1.1.3.3.1.14
Total microreflections including in-channel response as perceived on this interface, measured in dBc below the signal level. This object is not assumed to return an absolutely accurate value, but should give a rough indication of microreflections received on this interface. It is up to the implementor to provide information as accurate as possible.
OBJECT-TYPE    
  Integer32 0..255  

basDocsIfCmtsCmStatusChassis 1.3.6.1.4.1.3493.2.7.8.1.1.3.3.1.15
The BAS Chassis ID of this card.
OBJECT-TYPE    
  BasChassisId  

basDocsIfCmtsCmStatusSlot 1.3.6.1.4.1.3493.2.7.8.1.1.3.3.1.16
The BAS Slot ID of this card.
OBJECT-TYPE    
  BasSlotId  

basDocsIfCmtsCmStatusIf 1.3.6.1.4.1.3493.2.7.8.1.1.3.3.1.17
The BAS interface ID of this card.
OBJECT-TYPE    
  BasInterfaceId  

basDocsIfCmtsCmStatusLPort 1.3.6.1.4.1.3493.2.7.8.1.1.3.3.1.18
The BAS logical port ID of this card.
OBJECT-TYPE    
  BasLogicalPortId  

basDocsIfCmtsQosProfileTable 1.3.6.1.4.1.3493.2.7.8.1.1.3.6
Provides modulation profile information for this CMTS.
OBJECT-TYPE    
  SEQUENCE OF  
    BasDocsIfCmtsQosProfileEntry

basDocsIfCmtsQosProfileEntry 1.3.6.1.4.1.3493.2.7.8.1.1.3.6.1
Tok_String
OBJECT-TYPE    
  BasDocsIfCmtsQosProfileEntry  

basDocsIfCmtsQosProfilePermissions 1.3.6.1.4.1.3493.2.7.8.1.1.3.6.1.6
This object specifies permitted methods of creating entries in docsIfQosProfileTable. CreateByManagement(0) is set if entries can be created using SNMP. UpdateByManagement(1) is set if updating entries using SNMP is permitted. CreateByModems(2) is set if entries can be created based on information in REG-REQ MAC messages received from Cable Modems. Information in this object is only applicable if docsIfQosProfileTable is implemented as read-create. Otherwise, this object is implemented as read-only and returns CreateByModems(2). Either CreateByManagement(0) or CreateByModems(1) must be set when writing to this object.
OBJECT-TYPE    
  BITS createByManagement(0), updateByManagement(1), createByModems(2)  

basDocsIfCmtsQosProfileChassis 1.3.6.1.4.1.3493.2.7.8.1.1.3.6.1.7
The BAS Chassis ID of this card.
OBJECT-TYPE    
  BasChassisId  

basDocsIfCmtsQosProfileSlot 1.3.6.1.4.1.3493.2.7.8.1.1.3.6.1.8
The BAS Slot ID of this card.
OBJECT-TYPE    
  BasSlotId  

basDocsIfCmtsQosProfileIf 1.3.6.1.4.1.3493.2.7.8.1.1.3.6.1.9
The BAS interface ID of this card.
OBJECT-TYPE    
  BasInterfaceId  

basDocsIfCmtsQosProfileLPort 1.3.6.1.4.1.3493.2.7.8.1.1.3.6.1.10
The BAS logical port ID of this card.
OBJECT-TYPE    
  BasLogicalPortId  

basDocsIfCmtsMacToCmTable 1.3.6.1.4.1.3493.2.7.8.1.1.3.7
This is a table to provide a quick access index into the docsIfCmtsCmStatusTable. There is exactly one row in this table for each row in the docsIfCmtsCmStatusTable. In general, the management station should use this table only to get a pointer into the docsIfCmtsCmStatusTable (which corresponds to the CM's RF interface MAC address), and should not iterate (e.g. GetNext through) this table.
OBJECT-TYPE    
  SEQUENCE OF  
    BasDocsIfCmtsMacToCmEntry

basDocsIfCmtsMacToCmEntry 1.3.6.1.4.1.3493.2.7.8.1.1.3.7.1
A row in the docsIfCmtsMacToCmTable. An entry in this table exists for each Cable Modem that is connected to the CMTS implementing this table.
OBJECT-TYPE    
  BasDocsIfCmtsMacToCmEntry  

basDocsIfCmtsCmMac 1.3.6.1.4.1.3493.2.7.8.1.1.3.7.1.1
The RF side MAC address for the referenced CM. (E.g. the interface on the CM that has docsCableMacLayer(127) as its ifType.
OBJECT-TYPE    
  MacAddress  

basDocsIfCmtsCmPtr 1.3.6.1.4.1.3493.2.7.8.1.1.3.7.1.2
An row index into docsIfCmtsCmStatusTable. When queried with the correct instance value (e.g. a CM's MAC address), returns the index in docsIfCmtsCmStatusTable which represents that CM.
OBJECT-TYPE    
  Integer32 1..2147483647  

basDocsIfCmtsCmChassis 1.3.6.1.4.1.3493.2.7.8.1.1.3.7.1.3
The BAS Chassis ID of this card.
OBJECT-TYPE    
  BasChassisId  

basDocsIfCmtsCmSlot 1.3.6.1.4.1.3493.2.7.8.1.1.3.7.1.4
The BAS Slot ID of this card.
OBJECT-TYPE    
  BasSlotId  

basDocsIfCmtsCmIf 1.3.6.1.4.1.3493.2.7.8.1.1.3.7.1.5
The BAS interface ID of this card.
OBJECT-TYPE    
  BasInterfaceId  

basDocsIfCmtsCmLPort 1.3.6.1.4.1.3493.2.7.8.1.1.3.7.1.6
The BAS logical port ID of this card.
OBJECT-TYPE    
  BasLogicalPortId