ASCEND-HDSL2-MIB

File: ASCEND-HDSL2-MIB.mib (11749 bytes)

Imported modules

ASCEND-WAN-MIB RFC-1212

Imported symbols

wanTypeHdsl2 OBJECT-TYPE

Defined Types

Hdsl2LineStatusEntry  
SEQUENCE    
  hdsl2StatusIfEntryIndex INTEGER
  hdsl2StatusShelfIndex INTEGER
  hdsl2StatusSlotIndex INTEGER
  hdsl2StatusLineIndex INTEGER
  hdsl2StatusUnitType INTEGER
  hdsl2StatusLineState INTEGER
  hdsl2StatusOpRate INTEGER
  hdsl2StatusVendorId INTEGER
  hdsl2StatusMajorFirmWareVer INTEGER
  hdsl2StatusMinorFirmWareVer INTEGER
  hdsl2StatusHardWareVer INTEGER

Hdsl2LineStatisticEntry  
SEQUENCE    
  hdsl2StatIfEntryIndex INTEGER
  hdsl2StatShelfIndex INTEGER
  hdsl2StatSlotIndex INTEGER
  hdsl2StatLineIndex INTEGER
  hdsl2StatConnUpDays INTEGER
  hdsl2StatConnUpHours INTEGER
  hdsl2StatConnUpMinutes INTEGER
  hdsl2StatRxSignalPresent INTEGER
  hdsl2StatLineQualityDb INTEGER
  hdsl2StatUpDwnCntr INTEGER
  hdsl2StatLineSelfTest INTEGER
  hdsl2StatTxPower INTEGER
  hdsl2StatFramerCrcErrors INTEGER
  hdsl2StatFramerSyncStatus INTEGER
  hdsl2StatFramerLosdCnt INTEGER
  hdsl2StatFramerSegaCnt INTEGER
  hdsl2StatFramerSegdCnt INTEGER
  hdsl2StatFramerRxHecErrors INTEGER
  hdsl2StatBertTimer INTEGER
  hdsl2StatBertEna INTEGER
  hdsl2StatBertState INTEGER
  hdsl2StatBertErrorCounter INTEGER

Defined Values

hdsl2LineStatusTable 1.3.6.1.4.1.529.4.12.1
HDSL2 status parameters.
OBJECT-TYPE    
  SEQUENCE OF  
    Hdsl2LineStatusEntry

hdsl2LineStatusEntry 1.3.6.1.4.1.529.4.12.1.1
A interface status entry containing objects to describe the interface.
OBJECT-TYPE    
  Hdsl2LineStatusEntry  

hdsl2StatusIfEntryIndex 1.3.6.1.4.1.529.4.12.1.1.1
Interface group index assigned to this port.
OBJECT-TYPE    
  INTEGER  

hdsl2StatusShelfIndex 1.3.6.1.4.1.529.4.12.1.1.2
TNT's HDSL2 modules Shelf ID.
OBJECT-TYPE    
  INTEGER  

hdsl2StatusSlotIndex 1.3.6.1.4.1.529.4.12.1.1.3
TNT's HDSL2 modules Slot ID.
OBJECT-TYPE    
  INTEGER  

hdsl2StatusLineIndex 1.3.6.1.4.1.529.4.12.1.1.4
HDSL2 modules line ID.
OBJECT-TYPE    
  INTEGER  

hdsl2StatusUnitType 1.3.6.1.4.1.529.4.12.1.1.5
Unit type defines if the unit is operating either as a Central Office Equipment (COE) or Customer Premiss equipment (CPE).
OBJECT-TYPE    
  INTEGER other(1), coe(2), cpe(3)  

hdsl2StatusLineState 1.3.6.1.4.1.529.4.12.1.1.6
Interface state describes the current ports operating state. States are: Config, Pend Down, Up, Down, Start-up, or N/A.
OBJECT-TYPE    
  INTEGER other(1), configure(2), deactivate(3), deactive-lost(4), start-up(5), pend-port-up(6), up(7), pend-deactivate(8), out-of-service(9), analog-loopback(10), digital-loopback(11)  

hdsl2StatusOpRate 1.3.6.1.4.1.529.4.12.1.1.7
The current symetrical operation rate
OBJECT-TYPE    
  INTEGER m1552000(1552000)  

hdsl2StatusVendorId 1.3.6.1.4.1.529.4.12.1.1.8
Vendor identification.
OBJECT-TYPE    
  INTEGER  

hdsl2StatusMajorFirmWareVer 1.3.6.1.4.1.529.4.12.1.1.9
Major firmware version.
OBJECT-TYPE    
  INTEGER  

hdsl2StatusMinorFirmWareVer 1.3.6.1.4.1.529.4.12.1.1.10
Minor firmware version.
OBJECT-TYPE    
  INTEGER  

hdsl2StatusHardWareVer 1.3.6.1.4.1.529.4.12.1.1.11
Hardware version.
OBJECT-TYPE    
  INTEGER  

hdsl2LineStatisticTable 1.3.6.1.4.1.529.4.12.2
HDSL2 statistical parameters.
OBJECT-TYPE    
  SEQUENCE OF  
    Hdsl2LineStatisticEntry

hdsl2LineStatisticEntry 1.3.6.1.4.1.529.4.12.2.1
A interface statistical entry containing objects to describe the interface.
OBJECT-TYPE    
  Hdsl2LineStatisticEntry  

hdsl2StatIfEntryIndex 1.3.6.1.4.1.529.4.12.2.1.1
The interface groups interface index is used to index into this table.
OBJECT-TYPE    
  INTEGER  

hdsl2StatShelfIndex 1.3.6.1.4.1.529.4.12.2.1.2
HDSL2 modules Shelf ID.
OBJECT-TYPE    
  INTEGER  

hdsl2StatSlotIndex 1.3.6.1.4.1.529.4.12.2.1.3
HDSL2 modules Slot ID.
OBJECT-TYPE    
  INTEGER  

hdsl2StatLineIndex 1.3.6.1.4.1.529.4.12.2.1.4
HDSL2 modules interface ID.
OBJECT-TYPE    
  INTEGER  

hdsl2StatConnUpDays 1.3.6.1.4.1.529.4.12.2.1.5
Connection up day count.
OBJECT-TYPE    
  INTEGER  

hdsl2StatConnUpHours 1.3.6.1.4.1.529.4.12.2.1.6
Connection Up 24 hour count.
OBJECT-TYPE    
  INTEGER  

hdsl2StatConnUpMinutes 1.3.6.1.4.1.529.4.12.2.1.7
Connection up minute count.
OBJECT-TYPE    
  INTEGER  

hdsl2StatRxSignalPresent 1.3.6.1.4.1.529.4.12.2.1.8
Receive signal present detection.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

hdsl2StatLineQualityDb 1.3.6.1.4.1.529.4.12.2.1.9
Lines noise margin. Reliable data will transfer with a reading of ??? or greater.
OBJECT-TYPE    
  INTEGER  

hdsl2StatUpDwnCntr 1.3.6.1.4.1.529.4.12.2.1.10
Line Up Down counter value displays the number of times the interface transitions from a down to up state.
OBJECT-TYPE    
  INTEGER  

hdsl2StatLineSelfTest 1.3.6.1.4.1.529.4.12.2.1.11
Line hardware self test results (Passed or Failed).
OBJECT-TYPE    
  INTEGER other(4), selfTestFailed(1), localLoopBackFailed(2), passed(3)  

hdsl2StatTxPower 1.3.6.1.4.1.529.4.12.2.1.12
Lines transmit power.
OBJECT-TYPE    
  INTEGER 1..7fffffff  

hdsl2StatFramerCrcErrors 1.3.6.1.4.1.529.4.12.2.1.13
Lines framer CRC errors.
OBJECT-TYPE    
  INTEGER 1..7fffffff  

hdsl2StatFramerSyncStatus 1.3.6.1.4.1.529.4.12.2.1.14
Lines framer sync status .
OBJECT-TYPE    
  INTEGER 1..7fffffff  

hdsl2StatFramerLosdCnt 1.3.6.1.4.1.529.4.12.2.1.15
Lines framer ???.
OBJECT-TYPE    
  INTEGER 1..7fffffff  

hdsl2StatFramerSegaCnt 1.3.6.1.4.1.529.4.12.2.1.16
Lines framer ???.
OBJECT-TYPE    
  INTEGER 1..7fffffff  

hdsl2StatFramerSegdCnt 1.3.6.1.4.1.529.4.12.2.1.17
Lines framer ???.
OBJECT-TYPE    
  INTEGER 1..7fffffff  

hdsl2StatFramerRxHecErrors 1.3.6.1.4.1.529.4.12.2.1.18
Lines framer ???.
OBJECT-TYPE    
  INTEGER 1..7fffffff  

hdsl2StatBertTimer 1.3.6.1.4.1.529.4.12.2.1.19
BER test duration configuration. The BER test lasts for the duration of this timer.
OBJECT-TYPE    
  INTEGER one-minute(1), two-minutes(2), three-minutes(3), four-minutes(4), five-minutes(5), ten-minutes(6), fifteen-minutes(7), twenty-minutes(8), thirty-minutes(9)  

hdsl2StatBertEna 1.3.6.1.4.1.529.4.12.2.1.20
Enable/disable of the BER test. If nodes are connected, then the BER test is ran between the units. If this node is not connected to a remote node, then the interface is placed into analog loopback and the BER test is started.
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

hdsl2StatBertState 1.3.6.1.4.1.529.4.12.2.1.21
BER test states. When this node is not connected to another node, the test is disabled. When two nodes are connected then the BER test waits for the other node to start it's BER test and then starts collecting bit errors immediately.
OBJECT-TYPE    
  INTEGER active(1), stopped(2), start-up(3), waiting(4), pend-active(5), bert-los(6)  

hdsl2StatBertErrorCounter 1.3.6.1.4.1.529.4.12.2.1.22
BER test bit error counter.
OBJECT-TYPE    
  INTEGER