ADVANTECH-EKI-PRONEER-MIB

File: ADVANTECH-EKI-PRONEER-MIB.mib (336765 bytes)

Imported modules

Imported symbols

MODULE-IDENTITY	enterprises	OBJECT-TYPE
Integer32	Counter32	IpAddress
NOTIFICATION-TYPE	TimeTicks	OBJECT-GROUP
DisplayString	DateAndTime

Defined Types

LoggingBufferedEntry
SEQUENCE
	loggingBufferIndex	Integer32
	loggingBufferSeverity	INTEGER
	loggingBufferCategory	DisplayString
	loggingBufferTimeStamp	DisplayString
	loggingBufferMessage	DisplayString

LoggingFileEntry
SEQUENCE
	loggingFileIndex	Integer32
	loggingFileSeverity	INTEGER
	loggingFileCategory	DisplayString
	loggingFileTimeStamp	DisplayString
	loggingFileMessage	DisplayString

PortStatisticEntry
SEQUENCE
	portStatisticIndex	Integer32
	portCounterClear	INTEGER
	ifInOctets	Integer32
	ifInUcastPkts	Integer32
	ifInNUcastPkts	Integer32
	ifInDiscards	Integer32
	ifOutOctets	Integer32
	ifOutUcastPkts	Integer32
	ifOutNUcastPkts	Integer32
	ifOutDiscards	Integer32
	ifInMulticastPkts	Integer32
	ifInBroadcastPkts	Integer32
	ifOutMulticastPkts	Integer32
	ifOutBroadcastPkts	Integer32
	dot3StatsAlignmentErrors	Integer32
	dot3StatsFCSErrors	Integer32
	dot3StatsSingleCollisionFrames	Integer32
	dot3StatsMultipleCollisionFrames	Integer32
	dot3StatsDeferredTransmissions	Integer32
	dot3StatsLateCollisions	Integer32
	dot3StatsExcessiveCollisions	Integer32
	dot3StatsFrameTooLongs	Integer32
	dot3StatsSymbolErrors	Integer32
	dot3ControlInUnknownOpcodes	Integer32
	dot3InPauseFrames	Integer32
	dot3OutPauseFrames	Integer32

LagStatusEntry
SEQUENCE
	lagStatusIndex	Integer32
	lagStatusName	DisplayString
	lagStatusType	INTEGER
	lagStatusLinkState	INTEGER
	lagStatusActiveMember	DisplayString
	lagStatusStandbyMember	DisplayString

LacpInfoEntry
SEQUENCE
	lacpInfoLagIndex	DisplayString
	lacpInfoPortIndex	DisplayString
	lacpInfoPartnerSysId	DisplayString
	lacpInfoPnkey	DisplayString
	lacpInfoAtkey	DisplayString
	lacpInfoSel	DisplayString
	lacpInfoMux	DisplayString
	lacpInfoReceiv	DisplayString
	lacpInfoPrdtx	DisplayString
	lacpInfoAtstat	DisplayString
	lacpInfoPnstat	DisplayString

LLDPPortStatisticsEntry
SEQUENCE
	lldpPortStatIndex	Integer32
	lldpPortStatTotalTxFrame	Integer32
	lldpPortStatTotalRxFrame	Integer32
	lldpPortStatDiscardRxFrame	Integer32
	lldpPortStatErrorRxFrame	Integer32
	lldpPortStatDiscardRxTlv	Integer32
	lldpPortStatUnrecognizedRxTlv	Integer32
	lldpPortStatTotalRxAgeouts	Integer32

InterfaceIpv4Entry
SEQUENCE
	interfaceIpv4Index	Integer32
	interfaceIpv4Vlan	Integer32
	interfaceIpv4Mode	INTEGER
	interfaceIpv4Address	IpAddress
	interfaceIpv4SubnetMask	IpAddress
	interfaceIpv4Gateway	IpAddress
	interCurrIpv4DhcpState	INTEGER
	interCurrIpv4Address	IpAddress
	interCurrIpv4SubnetMask	IpAddress
	interCurrIpv4Gateway	IpAddress

IPv6InUseEntry
SEQUENCE
	ipv6InUseIndex	Integer32
	ipv6InUseAddress	DisplayString
	ipv6InUseSubnetMask	Integer32

SFPSerialInfoEntry
SEQUENCE
	sfpPortIndex	DisplayString
	sfpConnector	DisplayString
	sfpSpeed	DisplayString
	sfpVendorName	DisplayString
	sfpVendorPn	DisplayString
	spfVendorRev	DisplayString
	sfpVendorSn	DisplayString
	sfpDateCode	DisplayString

SFPDMIInfoEntry
SEQUENCE
	sfpDMIPortIndex	DisplayString
	sfpDMITemperature	DisplayString
	sfpDMIVoltage	DisplayString
	sfpDMITxBias	DisplayString
	sfpDMITxPower	DisplayString
	sfpDMIRxPower	DisplayString

SFPDMIAlarmInfoEntry
SEQUENCE
	sfpDMIAlarmPortIndex	DisplayString
	sfpDMITempHighAlarmState	INTEGER
	sfpDMITempHighAlarmValue	DisplayString
	sfpDMITempHighWarnState	INTEGER
	sfpDMITempHighWarnValue	DisplayString
	sfpDMITempLowAlarmState	INTEGER
	sfpDMITempLowAlarmValue	DisplayString
	sfpDMITempLowWarnState	INTEGER
	sfpDMITempLowWarnValue	DisplayString
	sfpDMIVoltageHighAlarmState	INTEGER
	sfpDMIVoltageHighAlarmValue	DisplayString
	sfpDMIVoltageHighWarnState	INTEGER
	sfpDMIVoltageHighWarnValue	DisplayString
	sfpDMIVoltageLowAlarmState	INTEGER
	sfpDMIVoltageLowAlarmValue	DisplayString
	sfpDMIVoltageLowWarnState	INTEGER
	sfpDMIVoltageLowWarnValue	DisplayString
	sfpDMITxBasisHighAlarmState	INTEGER
	sfpDMITxBasisHighAlarmValue	DisplayString
	sfpDMITxBasisHighWarnState	INTEGER
	sfpDMITxBasisHighWarnValue	DisplayString
	sfpDMITxBasisLowAlarmState	INTEGER
	sfpDMITxBasisLowAlarmValue	DisplayString
	sfpDMITxBasisLowWarnState	INTEGER
	sfpDMITxBasisLowWarnValue	DisplayString
	sfpDMITxPowerHighAlarmState	INTEGER
	sfpDMITxPowerHighAlarmValue	DisplayString
	sfpDMITxPowerHighWarnState	INTEGER
	sfpDMITxPowerHighWarnValue	DisplayString
	sfpDMITxPowerLowAlarmState	INTEGER
	sfpDMITxPowerLowAlarmValue	DisplayString
	sfpDMITxPowerLowWarnState	INTEGER
	sfpDMITxPowerLowWarnValue	DisplayString
	sfpDMIRxPowerHighAlarmState	INTEGER
	sfpDMIRxPowerHighAlarmValue	DisplayString
	sfpDMIRxPowerHighWarnState	INTEGER
	sfpDMIRxPowerHighWarnValue	DisplayString
	sfpDMIRxPowerLowAlarmState	INTEGER
	sfpDMIRxPowerLowAlarmValue	DisplayString
	sfpDMIRxPowerLowWarnState	INTEGER
	sfpDMIRxPowerLowWarnValue	DisplayString

PortSettingEntry
SEQUENCE
	portSettingIndex	Integer32
	description	DisplayString
	enableState	INTEGER
	linkStatus	INTEGER
	speed	INTEGER
	duplex	INTEGER
	flowControlConfig	INTEGER
	flowControlStatus	INTEGER

MirrorEntry
SEQUENCE
	sessionId	Integer32
	monitorSessionState	INTEGER
	destinationPort	Integer32
	ingressState	INTEGER
	sourceTxPort	BITS
	sourceRxPort	BITS

LagManagementEntry
SEQUENCE
	lagIndex	Integer32
	lagName	DisplayString
	lagType	INTEGER
	lagPorts	BITS
	lagLinkState	INTEGER
	lagActiveMember	DisplayString
	lagStandbyMember	DisplayString

LagPortEntry
SEQUENCE
	lagPortIndex	Integer32
	lagPortDescription	DisplayString
	lagPortType	DisplayString
	lagPortEnableState	INTEGER
	lagPortLinkStatus	INTEGER
	lagPortSpeed	INTEGER
	lagPortDuplex	INTEGER
	lagPortFlowCtrlConfig	INTEGER
	lagPortFlowCtrlStatus	INTEGER

LacpPortEntry
SEQUENCE
	lacpPortIndex	Integer32
	lacpPriority	Integer32
	lacpTimeout	INTEGER
	lacpPortMode	INTEGER

VlanEntry
SEQUENCE
	vlanIndex	Integer32
	vlanId	Integer32
	vlanNamePrefix	DisplayString
	vlanType	INTEGER
	vlanRowStatus	INTEGER

VlanInterfaceEntry
SEQUENCE
	vlanPortIndex	Integer32
	vlanInterfaceVlanMode	INTEGER
	vlanPvid	Integer32
	vlanAcceptedType	INTEGER
	vlanIngressFiltering	INTEGER

PortToVlanEntry
SEQUENCE
	portToVlanVlanIndex	Integer32
	portToVlanPortIndex	Integer32
	portToVlanVlanId	Integer32
	portToVlanInterfaceVlanMode	INTEGER
	portToVlanMembership	INTEGER
	portToVlanPvid	INTEGER

PortVlanEntry
SEQUENCE
	portVlanPortIndex	Integer32
	portVlanPortMode	INTEGER
	portVlanAdminVlans	DisplayString
	portVlanOperVlans	DisplayString

TelephonyOUIEntry
SEQUENCE
	telephonyOUIIndex	Integer32
	telephonyOUIAddress	DisplayString
	telephonyOUIDescription	DisplayString
	telephonyOUIRowStatus	INTEGER

TelephonyOUIPortEntry
SEQUENCE
	telephonyOUIPortIndex	Integer32
	telephonyOUIState	INTEGER
	telephonyOUICosMode	INTEGER

InterfaceVlanEntry
SEQUENCE
	interfaceVlanIndex	Integer32
	interfaceVlanId	Integer32
	interfaceVlanName	DisplayString
	interfaceVlanRowStatus	INTEGER

EeePortEntry
SEQUENCE
	eeePortIndex	Integer32
	eeeState	INTEGER

IgmpSnoopingEntry
SEQUENCE
	igmpSnoopingIndex	Integer32
	igmpSnoopingVlanId	Integer32
	igmpSnoopStatus	INTEGER
	routerPortsAutoLearn	INTEGER
	queryRobustness	Integer32
	queryInterval	Integer32
	queryMaxResponseInterval	Integer32
	lastMemberQueryCounter	Integer32
	lastMemberQueryInterval	Integer32
	immediateLeave	INTEGER
	operQueryRobustness	Integer32
	operQueryInterval	Integer32
	operQueryMaxResponseInterval	Integer32
	operLastMemberQueryCounter	Integer32
	operLastMemberQueryInterval	Integer32

IgmpQuerierEntry
SEQUENCE
	igmpQuerierVlanId	Integer32
	igmpQuerierState	INTEGER
	igmpQuerierStatus	INTEGER
	igmpQuerierVersion	INTEGER
	igmpQuerierIP	DisplayString

IgmpStaticGroupEntry
SEQUENCE
	igmpStaticGroupIndex	Integer32
	igmpStaticGroupVlanId	Integer32
	igmpStaticGroupIPaddress	IpAddress
	igmpStaticGroupMemberPorts	BITS
	igmpStaticGroupRowStatus	INTEGER

IgmpGroupEntry
SEQUENCE
	igmpGroupVlanId	Integer32
	igmpGroupIPaddress	IpAddress
	igmpGroupMemberPorts	DisplayString
	igmpGroupType	INTEGER
	igmpGroupLife	Integer32

IgmpRouterEntry
SEQUENCE
	igmpRouterVlanId	Integer32
	igmpRouterPort	DisplayString
	igmpRouterExpireTime	Integer32

MLDSnoopingEntry
SEQUENCE
	mldSnoopingIndex	Integer32
	mldSnoopingVlanId	Integer32
	mldSnoopStatus	INTEGER
	mldSnoopRouterPortsAutoLearn	INTEGER
	mldSnoopQueryRobustness	Integer32
	mldSnoopQueryInterval	Integer32
	mldSnoopQueryMaxResponseInterval	Integer32
	mldSnoopLastMemberQueryCounter	Integer32
	mldSnoopLastMemberQueryInterval	Integer32
	mldSnoopImmediateLeave	INTEGER
	operMldSnoopQueryRobustness	Integer32
	operMldSnoopQueryInterval	Integer32
	operMldSnoopQueryMaxResponseInterval	Integer32
	operMldSnoopLastMemberQueryCounter	Integer32
	operMldSnoopLastMemberQueryInterval	Integer32

MLDQuerierEntry
SEQUENCE
	mldQuerierVlanId	Integer32
	mldQuerierState	INTEGER
	mldQuerierStatus	INTEGER
	mldQuerierVersion	INTEGER
	mldQuerierIP	DisplayString

MLDStaticGroupEntry
SEQUENCE
	mldStaticGroupIndex	Integer32
	mldStaticGroupVlanId	Integer32
	mldStaticGroupIPaddress	DisplayString
	mldStaticGroupMemberPorts	BITS
	mldStaticGroupRowStatus	INTEGER

MLDGroupEntry
SEQUENCE
	mldGroupVlanId	Integer32
	mldGroupIPaddress	DisplayString
	mldGroupMemberPorts	DisplayString
	mldGroupType	INTEGER
	mldGroupLife	Integer32

MLDRouterEntry
SEQUENCE
	mldRouterVlanId	Integer32
	mldRouterPort	DisplayString
	mldRouterExpireTime	Integer32

StpPortEntry
SEQUENCE
	stpPortIndex	Integer32
	stpAdminEnable	INTEGER
	stpPathCost	Integer32
	stpEdgePort	INTEGER
	stpP2pMac	INTEGER
	stpMigrate	INTEGER

StpPortStatusEntry
SEQUENCE
	stpPortStatusIndex	Integer32
	stpPortPriority	Integer32
	stpPortPathCost	DisplayString
	stpPortDesignatedRootBridge	DisplayString
	stpPortRootPathCost	Integer32
	stpPortDesignatedBridge	DisplayString
	stpPortEdgrPortConf	DisplayString
	stpPortP2PMacConf	DisplayString
	stpPortRoles	INTEGER
	stpPortStatus	INTEGER

StpStatisticEntry
SEQUENCE
	stpStatisticPortIndex	Integer32
	configurationBPDUsReceived	Integer32
	tcnBPDUsReceived	Integer32
	configurationBPDUsTransmitted	Integer32
	tcnBPDUsTransmitted	Integer32

MSTIIDEntry
SEQUENCE
	mstiIDIndex	Integer32
	mstiVLANList	DisplayString

STPPriorityInfoEntry
SEQUENCE
	stpMstiIDIndex	Integer32
	stpPriorityValue	Integer32
	stpPriorityDefault	INTEGER

MSTStpPortStatusEntry
SEQUENCE
	mstStpPortStatusIndex	Integer32
	mstStpPortPriority	DisplayString
	mstStpPortPathCost	DisplayString
	mstStpPortDesignatedRootBridge	DisplayString
	mstStpPortRootPathCost	DisplayString
	mstStpPortDesignatedBridge	DisplayString
	mstStpPortEdgrPortConf	DisplayString
	mstStpPortP2PMacConf	DisplayString
	mstStpPortRoles	DisplayString
	mstStpPortStatus	DisplayString

QinQPortInfoEntry
SEQUENCE
	qinqPortIndex	INTEGER
	qinqOuterPVID	INTEGER
	qinqOuterMode	INTEGER

XRingEliteRingIDEntry
SEQUENCE
	xRingEliteRingIDIndex	Integer32
	xRingEliteRingID	Integer32
	xRingEliteRule	INTEGER
	xRingElitePort1	Integer32
	xRingElitePort2	Integer32
	xRingEliteRingIDStatus	DisplayString
	xRingElitePort1Status	DisplayString
	xRingElitePort2Status	DisplayString
	xRingEliteRowStatus	INTEGER

LoopbackPortEntry
SEQUENCE
	loopbackPortIndex	Integer32
	loopbackPortEnabled	INTEGER
	loopbackPortLoopStatus	INTEGER

XRingProInfoEntry
SEQUENCE
	xRingProInfoRingID	Integer32
	xRingProInfoMode	DisplayString
	xRingProInfoOperState	DisplayString
	xRingProInfoPort1	DisplayString
	xRingProInfoPort1FwdState	DisplayString
	xRingProInfoPort2	DisplayString
	xRingProInfoPort2FwdState	DisplayString
	xRingProInfoDel	INTEGER
	xRingProInfoRole	INTEGER

GMRPMulticastGroupEntry
SEQUENCE
	gmrpMulticastGroupIndex	Integer32
	gmrpMulticastGroupVlanId	Integer32
	gmrpMulticastGroupMacAddress	DisplayString
	gmrpMulticastGroupType	INTEGER
	gmrpMulticastGroupMemberPorts	DisplayString

ErpsGroupEntry
SEQUENCE
	erpsGroupRingIndex	Integer32
	erpsGroupInstance	Integer32
	erpsGroupRingId	Integer32
	erpsGroupRole	INTEGER
	erpsGroupState	DisplayString
	erpsGroupEastLink	Integer32
	erpsGroupEastLinkRPL	INTEGER
	erpsGroupEastLinkState	DisplayString
	erpsGroupWestLink	Integer32
	erpsGroupWestLinkRPL	INTEGER
	erpsGroupWestLinkState	DisplayString
	erpsGroupMEL	Integer32
	erpsGroupRAPSChannelVlan	Integer32
	erpsGroupTrafficChannel	Integer32
	erpsGroupRevertive	INTEGER
	erpsGroupType	INTEGER
	erpsGroupInterconnected	INTEGER
	erpsGroupChannel	INTEGER
	erpsGroupTcPropagation	INTEGER
	erpsWTRTimer	Integer32
	erpsGuardTimer	Integer32
	erpsHoldOffTimer	Integer32
	erpsGroupRowStatus	INTEGER

StaticMacSettingEntry
SEQUENCE
	staticMacSettingIndex	Integer32
	staticMacSettingMacAddress	DisplayString
	staticMacSettingVlan	Integer32
	staticMacSettingPort	Integer32
	staticMacSettingRowStatus	INTEGER

MacAddressInfoEntry
SEQUENCE
	macAddressInfoIndex	Integer32
	macAddressInfoMAC	DisplayString
	macAddressInfoVlan	Integer32
	macAddressInfoType	INTEGER
	macAddressInfoPort	DisplayString
	addtoStaticMacTable	INTEGER

PortSecSettingEntry
SEQUENCE
	stromControlPortIndex	Integer32
	stromControlPortState	INTEGER
	stromControlPortAction	INTEGER
	enablebroadcast	INTEGER
	broadcastRate	Integer32
	enableunknownMulticast	INTEGER
	unknownMulticastRate	Integer32
	enableunknownUnicast	INTEGER
	unknownUnicastRate	Integer32

ProtectedPortEntry
SEQUENCE
	protectedPortIndex	Integer32
	protectedPortType	INTEGER

DosPortEntry
SEQUENCE
	dosportIndex	Integer32
	dosProtection	INTEGER

PortSecurityEntry
SEQUENCE
	portSecurityPortIndex	Integer32
	portSecurityEnabled	INTEGER
	portSecurityFDBLimit	Integer32
	portSecurityViolationMACNotify	INTEGER

IPSecurityEntry
SEQUENCE
	ipSecurityIndex	Integer32
	ipSecurityIPAddr	IpAddress
	ipSecurityIPMask	IpAddress
	ipSecurityService	BITS
	ipSecurityVlanId	Integer32
	ipSecurityRowStatus	INTEGER

IEEE8021xPortEntry
SEQUENCE
	ieee8021xPortIndex	Integer32
	ieee8021xPortState	INTEGER

MacAclEntry
SEQUENCE
	macAclIndex	Integer32
	destinationMacAddress	DisplayString
	destinationMacMask	DisplayString
	sourceMacAddress	DisplayString
	sourceMacMask	DisplayString
	macAclEtherType	Integer32
	macAclVlanID	Integer32
	macAclPortList	BITS
	macAclAction	INTEGER
	macAclActiveStatus	INTEGER
	macAclRowStatus	INTEGER

IpAclEntry
SEQUENCE
	ipAclIndex	Integer32
	destinationIpAddress	IpAddress
	destinationIpMask	IpAddress
	sourceIpAddress	IpAddress
	sourceIpMask	IpAddress
	ipProtocol	INTEGER
	l4DestinationPort	Integer32
	l4SourcePort	Integer32
	ipAclPortList	BITS
	ipAclAction	INTEGER
	ipAclActiveStatus	INTEGER
	ipAclRowStatus	INTEGER

IpSourceGuardEntry
SEQUENCE
	ipSourceGuardIndex	Integer32
	ipSourceGuardSourceIp	IpAddress
	ipSourceGuardSourceMac	DisplayString
	ipSourceGuardPort	Integer32
	ipSourceGuardRowStatus	INTEGER

DhcpSnoopingEntry
SEQUENCE
	dhcpSnoopingIndex	Integer32
	dhcpSnoopingMac	DisplayString
	dhcpSnoopingIp	IpAddress
	dhcpSnoopingLeaseTime	INTEGER
	dhcpSnoopingVlanId	Integer32
	dhcpSnoopingPort	Integer32

ArpSpoofingEntry
SEQUENCE
	arpSpoofingIndex	Integer32
	arpSpoofingSourceMac	DisplayString
	arpSpoofingSourceIp	IpAddress
	arpSpoofingRowStatus	INTEGER

QosPortSettingEntry
SEQUENCE
	qosPortIndex	Integer32
	qosPortCos	Integer32
	qosPortRemarkCoS	INTEGER
	qosPortRemarkDSCP	INTEGER
	qosPortRemarkIPPrecedence	INTEGER

QueueSettingEntry
SEQUENCE
	queueIndex	Integer32
	queueMethod	INTEGER
	queueWeight	Integer32
	queuePercentOfWRRBandwidth	DisplayString

CostoQueueMapEntry
SEQUENCE
	cosIndex	Integer32
	cosQueue	Integer32

QueueToCosMapEntry
SEQUENCE
	queuetoCosIndex	Integer32
	queueCos	Integer32

DscptoQueueMapEntry
SEQUENCE
	dscpIndex	Integer32
	dscpQueue	Integer32

QueuetoDSCPMapEntry
SEQUENCE
	queuetoDSCPIndex	Integer32
	queuDscp	Integer32

IpPrecedencetoQueueMapEntry
SEQUENCE
	ipPrecedenceIndex	Integer32
	ipPrecedenceQueue	Integer32

QueueToipPrecedenceMapEntry
SEQUENCE
	queueToipPrecedenceIndex	Integer32
	ipPrecedence	Integer32

QosPortEntry
SEQUENCE
	qosBasicPortIndex	Integer32
	qosBasicPortTrust	INTEGER

IngressBandwidthEntry
SEQUENCE
	ingressBandwidthPortIndex	Integer32
	ingressBandwidthState	INTEGER
	ingressBandwidthRate	Integer32

EgressBandwidthEntry
SEQUENCE
	egressBandwidthPortIndex	Integer32
	egressBandwidthState	INTEGER
	egressBandwidthRate	Integer32

EgressqueueBandwidthEntry
SEQUENCE
	egressqueueBandwidthPortIndex	Integer32
	egressqueueBandwidthQueueIndex	Integer32
	egressqueueBandwidthState	INTEGER
	egressqueueBandwidthCir	Integer32

LldpPortConfEntry
SEQUENCE
	lldpPortIndex	Integer32
	lldpPortState	INTEGER
	lldpPortOptionalTLVs	BITS
	lldpPortVlans	DisplayString

LldpLocalPortStatusEntry
SEQUENCE
	lldpLocalPortIndex	Integer32
	lldpLocalPortStatus	INTEGER
	lldpLocalPortChassisIDsubtype	DisplayString
	lldpLocalPortChassisID	DisplayString
	lldpLocalPortSystemname	DisplayString
	lldpLocalPortSystemdescription	DisplayString
	lldpLocalPortSupportedsystemcapabilities	DisplayString
	lldpLocalPortEnablesystemcapabilities	DisplayString
	lldpLocalPortIDsubtype	DisplayString
	lldpLocalPortID	DisplayString
	lldpLocalPortDescription	DisplayString
	lldpLocalPortManagementAddress	DisplayString
	lldpLocalPortAuto-negosupported	DisplayString
	lldpLocalPortAuto-negoenabled	DisplayString
	lldpLocalPortAuto-negoAdvertisedCapabilities	DisplayString
	lldpLocalPortOperationMAUtype	DisplayString
	lldpLocalPortIeee8023MaxFrameSize	DisplayString
	lldpLocalPortAggregationCapability	DisplayString
	lldpLocalPortAggregationStatus	DisplayString
	lldpLocalPortAggregationPortID	DisplayString
	lldpLocalPortPvid	DisplayString
	lldpLocalPortVlanName	DisplayString

LldpremoteDeviceEntry
SEQUENCE
	lldpremoteDeviceIndex	Integer32
	lldpremoteDeviceLocalPort	DisplayString
	lldpremoteDeviceChassisIDsubtype	DisplayString
	lldpremoteDeviceChassisID	DisplayString
	lldpremoteDevicePortIDsubtype	DisplayString
	lldpremoteDevicePortID	DisplayString
	lldpremoteDeviceSystemName	DisplayString
	lldpremoteDeviceTimetolive	DisplayString
	lldpremoteDeviceEntryIndex	DisplayString
	lldpremoteDevicePortDescription	DisplayString
	lldpremoteDeviceSystemdescription	DisplayString
	lldpremoteDeviceSupportedsystemcapabilities	DisplayString
	lldpremoteDeviceEnablesystemcapabilities	DisplayString
	lldpremoteDeviceManagementAddress	DisplayString
	lldpremoteDeviceAuto-negosupported	DisplayString
	lldpremoteDeviceAuto-negoenabled	DisplayString
	lldpremoteDeviceAuto-negoAdvertisedCapabilities	DisplayString
	lldpremoteDeviceOperationMAUtype	DisplayString
	lldpremoteDeviceMdipowersupportportclass	DisplayString
	lldpremoteDevicePsemdipowersupport	DisplayString
	lldpremoteDevicePsemdipowerstatus	DisplayString
	lldpremoteDevicePsepowerpaircontrolability	DisplayString
	lldpremoteDevicePsepowerpair	DisplayString
	lldpremoteDevicePsepowerclass	DisplayString
	lldpremoteDeviceIeee8023MaxFrameSize	DisplayString
	lldpremoteDeviceAggregationCapability	DisplayString
	lldpremoteDeviceAggregationStatus	DisplayString
	lldpremoteDeviceAggregationPortID	DisplayString
	lldpremoteDevicePvid	DisplayString
	lldpremoteDeviceVlanName	DisplayString
	lldpremoteDeviceRowStatus	INTEGER

LLDPOverloadingEntry
SEQUENCE
	lldpOverloadingPortIndex	Integer32
	lldpOverloadingTotal	Integer32
	lldpOverloadingLeftToSend	Integer32
	lldpOverloadingStatus	DisplayString
	lldpOverloadingMandatoryTLVs	DisplayString
	lldpOverloadingIeee8023TLVs	DisplayString
	lldpOverloadingOptionalTLVs	DisplayString
	lldpOverloadingIeee8021TLVs	DisplayString

CommunityEntry
SEQUENCE
	snmpCommunityIndex	Integer32
	snmpCommunityString	DisplayString
	snmpCommunityAccessRight	INTEGER
	snmpCommunityRowStatus	INTEGER

SnmpTrapHostEntry
SEQUENCE
	snmpTrapHostIndex	Integer32
	snmpTrapHostIpaddress	DisplayString
	snmpTrapHostCommunityName	DisplayString
	snmpTrapHostVersion	INTEGER
	snmpTrapHostRowStatus	INTEGER

SNMPv3UserEntry
SEQUENCE
	snmpv3UserIndex	Integer32
	snmpv3UserName	DisplayString
	snmpv3UserAccessRight	INTEGER
	snmpv3UserAuthProtocol	INTEGER
	snmpv3UserAuthPassword	DisplayString
	snmpv3UserPrivProtocol	INTEGER
	snmpv3UserPrivPassword	DisplayString
	snmpv3UserRowStatus	INTEGER

PoEPortSettingEntry
SEQUENCE
	poePortIndex	Integer32
	poePortState	INTEGER
	poePortLegacy	INTEGER
	poePortPowerLimitClass	INTEGER
	poePortPriority	INTEGER
	poePortPowerLimit	Integer32

PoEPortStatusEntry
SEQUENCE
	poePortStatusIndex	Integer32
	poePortCurrent	DisplayString
	poePortVoltage	DisplayString
	poePortPower	DisplayString
	poePortTemp	DisplayString

DHCPServerPortEntry
SEQUENCE
	dhcpServerPortIndex	Integer32
	dhcpServerPortLowIP	IpAddress
	dhcpServerPortHighIP	IpAddress
	dhcpServerPortMask	IpAddress
	dhcpServerPortGW	IpAddress
	dhcpServerPortDNS	IpAddress
	dhcpServerPortStatus	INTEGER
	dhcpServerPortClear	INTEGER

DHCPServerOpt82Entry
SEQUENCE
	dhcpServerOpt82Index	Integer32
	dhcpServerOpt82CircuitIDFormat	INTEGER
	dhcpServerOpt82CircuitID	DisplayString
	dhcpServerOpt82RemoteIDFormat	INTEGER
	dhcpServerOpt82RemoteID	DisplayString
	dhcpServerOpt82LowIP	IpAddress
	dhcpServerOpt82HighIP	IpAddress
	dhcpServerOpt82Mask	IpAddress
	dhcpServerOpt82GW	IpAddress
	dhcpServerOpt82DNS	IpAddress
	dhcpServerOpt82Status	INTEGER
	dhcpServerOpt82Clear	INTEGER

DHCPServerLeaseEntry
SEQUENCE
	dhcpServerLeaseIndex	Integer32
	dhcpServerLeaseIp	DisplayString
	dhcpServerLeaseClientMac	DisplayString
	dhcpServerLeaseStartTime	DisplayString
	dhcpServerLeaseEndTime	DisplayString
	dhcpServerLeaseType	DisplayString

DHCPServerVlanEntry
SEQUENCE
	dhcpServerVlanIndex	Integer32
	dhcpServerVlanId	Integer32
	dhcpServerVlanLowIP	IpAddress
	dhcpServerVlanHighIP	IpAddress
	dhcpServerVlanMask	IpAddress
	dhcpServerVlanGW	IpAddress
	dhcpServerVlanDNS	IpAddress
	dhcpServerVlanStatus	INTEGER
	dhcpServerVlanClear	INTEGER

DhcpServerClientMacEntry
SEQUENCE
	dhcpServerClientMacEntryID	Integer32
	dhcpServerClientMacEntryMac	DisplayString
	dhcpServerClientMacEntryIP	IpAddress
	dhcpServerClientMacEntryMask	IpAddress
	dhcpServerClientMacEntryGW	IpAddress
	dhcpServerClientMacEntryDNS	IpAddress
	dhcpServerClientMacEntryRowStatus	INTEGER

SMTPProfileEntry
SEQUENCE
	smtpProfileIndex	Integer32
	smtpServerIp	DisplayString
	smtpServerPort	Integer32
	smtpSenderMail	DisplayString
	smtpTargetMail1	DisplayString
	smtpTargetMail2	DisplayString
	smtpTargetMail3	DisplayString
	smtpTargetMail4	DisplayString
	smtpTargetMail5	DisplayString
	smtpTargetMail6	DisplayString
	smtpTargetMail7	DisplayString
	smtpTargetMail8	DisplayString

RMONStatisticsEntry
SEQUENCE
	rmonStatisticsIndex	Integer32
	rmonStatisticsPort	Integer32
	rmonStatisticsDropEvents	Counter32
	rmonStatisticsOctets	Counter32
	rmonStatisticsPackets	Counter32
	rmonStatisticsBroadcast	Counter32
	rmonStatisticsMulticast	Counter32
	rmonStatisticsOwner	DisplayString
	rmonStatisticsRowStatus	INTEGER

RMONHistoryEntry
SEQUENCE
	rmonHistoryIndex	Integer32
	rmonHistoryPort	Integer32
	rmonHistoryBucketsRequest	Integer32
	rmonHistoryInterval	Integer32
	rmonHistoryOwner	DisplayString
	rmonHistoryRowStatus	INTEGER

RMONAlarmEntry
SEQUENCE
	rmonAlarmIndex	Integer32
	rmonAlarmInterval	Integer32
	rmonAlarmVariable	DisplayString
	rmonAlarmSampleType	INTEGER
	rmonAlarmRisingThreshold	Integer32
	rmonAlarmFallingThreshold	Integer32
	rmonAlarmRisingEventIndex	Integer32
	rmonAlarmFallingEventIndex	Integer32
	rmonAlarmOwner	DisplayString
	rmonAlarmRowStatus	INTEGER

RMONEventEntry
SEQUENCE
	rmonEventIndex	Integer32
	rmonEventDescription	DisplayString
	rmonEventType	INTEGER
	rmonEventCommunity	DisplayString
	rmonEventOwner	DisplayString
	rmonEventRowStatus	INTEGER

NtpServerEntry
SEQUENCE
	ntpServerIndex	Integer32
	ntpServerIp	IpAddress

LocalLoggingEntry
SEQUENCE
	localLoggingIndex	Integer32
	bufferedtarget	INTEGER
	localLoggingStatus	INTEGER
	localLoggingSeverity	BITS

RemoteloggingEntry
SEQUENCE
	remoteloggingIndex	Integer32
	remoteloggingAddress	IpAddress
	remoteloggingPort	Integer32
	remoteloggingSeverity	BITS
	remoteloggingFacility	INTEGER
	remoteloggingRowStatus	INTEGER

LedEventInfoEntry
SEQUENCE
	ledEventIndex	Integer32
	ledType	DisplayString
	ledEvent	DisplayString
	ledState	DisplayString
	ledErrorTimes	Integer32

ImageInfoEntry
SEQUENCE
	flashPartition	Integer32
	imageName	DisplayString
	imageSize	Integer32
	createdTime	DisplayString
	imageVersion	DisplayString

LocalUserEntry
SEQUENCE
	localUserIndex	Integer32
	localUserName	DisplayString
	localUserPasswordType	INTEGER
	localUserPassword	DisplayString
	localUserPrivilegeType	INTEGER
	localUserRowStatus	INTEGER

Defined Values

advantech		1.3.6.1.4.1.10297
The MIB module is for Advantech switch, e.g. EKI-XXXX, etc. Copyright (C) Advantech iConnectivity Group(2014).
MODULE-IDENTITY

aSwitchMIB		1.3.6.1.4.1.10297.202
OBJECT IDENTIFIER

proneer		1.3.6.1.4.1.10297.202.7000
OBJECT IDENTIFIER

monitoring		1.3.6.1.4.1.10297.202.7000.1
OBJECT IDENTIFIER

system		1.3.6.1.4.1.10297.202.7000.2
OBJECT IDENTIFIER

l2switching		1.3.6.1.4.1.10297.202.7000.3
OBJECT IDENTIFIER

macAddressTable		1.3.6.1.4.1.10297.202.7000.4
OBJECT IDENTIFIER

security		1.3.6.1.4.1.10297.202.7000.5
OBJECT IDENTIFIER

qos		1.3.6.1.4.1.10297.202.7000.6
OBJECT IDENTIFIER

management		1.3.6.1.4.1.10297.202.7000.7
OBJECT IDENTIFIER

diagnostics		1.3.6.1.4.1.10297.202.7000.8
OBJECT IDENTIFIER

maintenance		1.3.6.1.4.1.10297.202.7000.9
OBJECT IDENTIFIER

traps		1.3.6.1.4.1.10297.202.7000.99
OBJECT IDENTIFIER

deviceInfo		1.3.6.1.4.1.10297.202.7000.1.1
OBJECT IDENTIFIER

loggingMessage		1.3.6.1.4.1.10297.202.7000.1.2
OBJECT IDENTIFIER

portMonitoring		1.3.6.1.4.1.10297.202.7000.1.3
OBJECT IDENTIFIER

linkAggregation		1.3.6.1.4.1.10297.202.7000.1.4
OBJECT IDENTIFIER

lldpStatistics		1.3.6.1.4.1.10297.202.7000.1.5
OBJECT IDENTIFIER

igmpStatistics		1.3.6.1.4.1.10297.202.7000.1.6
OBJECT IDENTIFIER

mldStatistics		1.3.6.1.4.1.10297.202.7000.1.7
OBJECT IDENTIFIER

systemName		1.3.6.1.4.1.10297.202.7000.1.1.1
System name of the switch
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..128)

systemLocation		1.3.6.1.4.1.10297.202.7000.1.1.2
System location of the switch.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

systemContact		1.3.6.1.4.1.10297.202.7000.1.1.3
System contact of the switch
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..255)

macAddress		1.3.6.1.4.1.10297.202.7000.1.1.4
MAC address of the switch.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

ipAddress		1.3.6.1.4.1.10297.202.7000.1.1.5
IP address of the switch.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

subnetMask		1.3.6.1.4.1.10297.202.7000.1.1.6
Subnet mask of the switch.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

gateway		1.3.6.1.4.1.10297.202.7000.1.1.7
Default gateway of the switch.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

loaderVersion		1.3.6.1.4.1.10297.202.7000.1.1.8
Boot loader version of the switch.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

loaderDate		1.3.6.1.4.1.10297.202.7000.1.1.9
Boot loader date of the switch.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

firmwareVersion		1.3.6.1.4.1.10297.202.7000.1.1.10
Firmware version of the switch.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

firmwareDate		1.3.6.1.4.1.10297.202.7000.1.1.11
Firmware release date of the switch.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

systemObjectID		1.3.6.1.4.1.10297.202.7000.1.1.12
SNMP system object ID of the switch.
Status: current	Access: read-only
OBJECT-TYPE
	OBJECT IDENTIFIER

systemUpTime		1.3.6.1.4.1.10297.202.7000.1.1.13
The time since the switch was last re-initialized.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

ledStatus		1.3.6.1.4.1.10297.202.7000.1.1.14
OBJECT IDENTIFIER

ledSYSStatus		1.3.6.1.4.1.10297.202.7000.1.1.14.1
The LED status of system operating.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notSupported(0), up(1), down(2)

ledRMStatus		1.3.6.1.4.1.10297.202.7000.1.1.14.2
The LED status of ring master.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notSupported(0), up(1), down(2)

ledPWR1Status		1.3.6.1.4.1.10297.202.7000.1.1.14.3
The LED status of power input 1.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notSupported(0), up(1), down(2)

ledPWR2Status		1.3.6.1.4.1.10297.202.7000.1.1.14.4
The LED status of power input 2.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notSupported(0), up(1), down(2)

ledAlarmStatus		1.3.6.1.4.1.10297.202.7000.1.1.14.5
The LED status of alarm.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notSupported(0), up(1), down(2)

ledPFAILStatus		1.3.6.1.4.1.10297.202.7000.1.1.14.6
The LED status of P-Fail.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notSupported(0), up(1), down(2)

ledRFAILStatus		1.3.6.1.4.1.10297.202.7000.1.1.14.7
The LED status of R-Fail.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notSupported(0), up(1), down(2)

ledLOOPStatus		1.3.6.1.4.1.10297.202.7000.1.1.14.8
The LED status of loop detection.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notSupported(0), up(1), down(2)

ledTempStatus		1.3.6.1.4.1.10297.202.7000.1.1.14.9
The LED status of system temperature.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notSupported(0), up(1), down(2)

buildVersion		1.3.6.1.4.1.10297.202.7000.1.1.15
Build version of the switch.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

loggingBufferTable		1.3.6.1.4.1.10297.202.7000.1.2.1
The table of the logging buffer
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LoggingBufferedEntry

loggingBufferEntry		1.3.6.1.4.1.10297.202.7000.1.2.1.1
The entry of the logging buffer
Status: current	Access: not-accessible
OBJECT-TYPE
	LoggingBufferedEntry

loggingBufferIndex		1.3.6.1.4.1.10297.202.7000.1.2.1.1.1
The index of the logging buffer
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..65535

loggingBufferSeverity		1.3.6.1.4.1.10297.202.7000.1.2.1.1.2
The severity of the logging buffer.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	emerg(0), alert(1), crit(2), error(3), warning(4), notice(5), info(6), debug(7)

loggingBufferCategory		1.3.6.1.4.1.10297.202.7000.1.2.1.1.3
The category of the logging buffer.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

loggingBufferTimeStamp		1.3.6.1.4.1.10297.202.7000.1.2.1.1.4
The time stamp of the logging buffer.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

loggingBufferMessage		1.3.6.1.4.1.10297.202.7000.1.2.1.1.5
The messge of the logging buffer.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

clearBufferedMsg		1.3.6.1.4.1.10297.202.7000.1.2.2
Delete the logging message in buffer.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	clear(1)

loggingFileTable		1.3.6.1.4.1.10297.202.7000.1.2.3
The table of the logging file
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LoggingFileEntry

loggingFileEntry		1.3.6.1.4.1.10297.202.7000.1.2.3.1
The entry of the logging file
Status: current	Access: not-accessible
OBJECT-TYPE
	LoggingFileEntry

loggingFileIndex		1.3.6.1.4.1.10297.202.7000.1.2.3.1.1
The index of the logging file
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	1..65535

loggingFileSeverity		1.3.6.1.4.1.10297.202.7000.1.2.3.1.2
The severity of the logging file
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	emerg(0), alert(1), crit(2), error(3), warning(4), notice(5), info(6), debug(7)

loggingFileCategory		1.3.6.1.4.1.10297.202.7000.1.2.3.1.3
The category of the logging file
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

loggingFileTimeStamp		1.3.6.1.4.1.10297.202.7000.1.2.3.1.4
The time stamp of the logging file
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

loggingFileMessage		1.3.6.1.4.1.10297.202.7000.1.2.3.1.5
The message of the logging file
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

clearFileMsg		1.3.6.1.4.1.10297.202.7000.1.2.4
Delete the logging message in file.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	clear(1)

portStatisticTable		1.3.6.1.4.1.10297.202.7000.1.3.1
The table of the RMON counters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PortStatisticEntry

portStatisticEntry		1.3.6.1.4.1.10297.202.7000.1.3.1.1
The entry of the RMON counters.
Status: current	Access: not-accessible
OBJECT-TYPE
	PortStatisticEntry

portStatisticIndex		1.3.6.1.4.1.10297.202.7000.1.3.1.1.1
The port index of the port counters.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

portCounterClear		1.3.6.1.4.1.10297.202.7000.1.3.1.1.2
Clear the port counter.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nothing(0), clear(1)

ifInOctets		1.3.6.1.4.1.10297.202.7000.1.3.1.1.3
The total number of octets received on the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ifInUcastPkts		1.3.6.1.4.1.10297.202.7000.1.3.1.1.4
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ifInNUcastPkts		1.3.6.1.4.1.10297.202.7000.1.3.1.1.5
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast or broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime. This object is deprecated in favour of ifInMulticastPkts and ifInBroadcastPkts.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ifInDiscards		1.3.6.1.4.1.10297.202.7000.1.3.1.1.6
The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ifOutOctets		1.3.6.1.4.1.10297.202.7000.1.3.1.1.7
The total number of octets transmitted out of the interface, including framing characters. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ifOutUcastPkts		1.3.6.1.4.1.10297.202.7000.1.3.1.1.8
The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ifOutNUcastPkts		1.3.6.1.4.1.10297.202.7000.1.3.1.1.9
The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime. This object is deprecated in favour of ifOutMulticastPkts and ifOutBroadcastPkts.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ifOutDiscards		1.3.6.1.4.1.10297.202.7000.1.3.1.1.10
The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ifInMulticastPkts		1.3.6.1.4.1.10297.202.7000.1.3.1.1.11
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ifInBroadcastPkts		1.3.6.1.4.1.10297.202.7000.1.3.1.1.12
The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ifOutMulticastPkts		1.3.6.1.4.1.10297.202.7000.1.3.1.1.13
The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer protocol, this includes both Group and Functional addresses. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ifOutBroadcastPkts		1.3.6.1.4.1.10297.202.7000.1.3.1.1.14
The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dot3StatsAlignmentErrors		1.3.6.1.4.1.10297.202.7000.1.3.1.1.15
A count of frames received on a particular interface that are not an integral number of octets in length and do not pass the FCS check. The count represented by an instance of this object is incremented when the alignmentError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions pertain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. This counter does not increment for group encoding schemes greater than 4 bits per group. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCStatsAlignmentErrors object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dot3StatsFCSErrors		1.3.6.1.4.1.10297.202.7000.1.3.1.1.16
A count of frames received on a particular interface that are an integral number of octets in length but do not pass the FCS check. This count does not include frames received with frame-too-long or frame-too-short error. The count represented by an instance of this object is incremented when the frameCheckError status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions pertain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. Note: Coding errors detected by the physical layer for speeds above 10 Mb/s will cause the frame to fail the FCS check. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCStatsFCSErrors object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dot3StatsSingleCollisionFrames		1.3.6.1.4.1.10297.202.7000.1.3.1.1.17
A count of frames that are involved in a single collision, and are subsequently transmitted successfully. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsMultipleCollisionFrames object. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dot3StatsMultipleCollisionFrames		1.3.6.1.4.1.10297.202.7000.1.3.1.1.18
A count of frames that are involved in more than one collision and are subsequently transmitted successfully. A frame that is counted by an instance of this object is also counted by the corresponding instance of either the ifOutUcastPkts, ifOutMulticastPkts, or ifOutBroadcastPkts, and is not counted by the corresponding instance of the dot3StatsSingleCollisionFrames object. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dot3StatsDeferredTransmissions		1.3.6.1.4.1.10297.202.7000.1.3.1.1.19
A count of frames for which the first transmission attempt on a particular interface is delayed because the medium is busy. The count represented by an instance of this object does not include frames involved in collisions. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dot3StatsLateCollisions		1.3.6.1.4.1.10297.202.7000.1.3.1.1.20
The number of times that a collision is detected on a particular interface later than one slotTime into the transmission of a packet. A (late) collision included in a count represented by an instance of this object is also considered as a (generic) collision for purposes of other collision-related statistics.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dot3StatsExcessiveCollisions		1.3.6.1.4.1.10297.202.7000.1.3.1.1.21
A count of frames for which transmission on a particular interface fails due to excessive collisions. This counter does not increment when the interface is operating in full-duplex mode. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dot3StatsFrameTooLongs		1.3.6.1.4.1.10297.202.7000.1.3.1.1.22
A count of frames received on a particular interface that exceed the maximum permitted frame size. The count represented by an instance of this object is incremented when the frameTooLong status is returned by the MAC service to the LLC (or other MAC user). Received frames for which multiple error conditions pertain are, according to the conventions of IEEE 802.3 Layer Management, counted exclusively according to the error status presented to the LLC. For interfaces operating at 10 Gb/s, this counter can roll over in less than 80 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCStatsFrameTooLongs object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dot3StatsSymbolErrors		1.3.6.1.4.1.10297.202.7000.1.3.1.1.23
For an interface operating at 100 Mb/s, the number of times there was an invalid data symbol when a valid carrier was present. For an interface operating in half-duplex mode at 1000 Mb/s, the number of times the receiving media is non-idle (a carrier event) for a period of time equal to or greater than slotTime, and during which there was at least one occurrence of an event that causes the PHY to indicate 'Data reception error' or 'carrier extend error' on the GMII. For an interface operating in full-duplex mode at 1000 Mb/s, the number of times the receiving media is non-idle (a carrier event) for a period of time equal to or greater than minFrameSize, and during which there was at least one occurrence of an event that causes the PHY to indicate 'Data reception error' on the GMII. For an interface operating at 10 Gb/s, the number of times the receiving media is non-idle (a carrier event) for a period of time equal to or greater than minFrameSize, and during which there was at least one occurrence of an event that causes the PHY to indicate 'Receive Error' on the XGMII. The count represented by an instance of this object is incremented at most once per carrier event, even if multiple symbol errors occur during the carrier event. This count does not increment if a collision is present. This counter does not increment when the interface is operating at 10 Mb/s. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCStatsSymbolErrors object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dot3ControlInUnknownOpcodes		1.3.6.1.4.1.10297.202.7000.1.3.1.1.24
A count of MAC Control frames received on this interface that contain an opcode that is not supported by this device. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCControlInUnknownOpcodes object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dot3InPauseFrames		1.3.6.1.4.1.10297.202.7000.1.3.1.1.25
A count of MAC Control frames received on this interface with an opcode indicating the PAUSE operation. This counter does not increment when the interface is operating in half-duplex mode. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCInPauseFrames object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

dot3OutPauseFrames		1.3.6.1.4.1.10297.202.7000.1.3.1.1.26
A count of MAC Control frames transmitted on this interface with an opcode indicating the PAUSE operation. This counter does not increment when the interface is operating in half-duplex mode. For interfaces operating at 10 Gb/s, this counter can roll over in less than 5 minutes if it is incrementing at its maximum rate. Since that amount of time could be less than a management station's poll cycle time, in order to avoid a loss of information, a management station is advised to poll the dot3HCOutPauseFrames object for 10 Gb/s or faster interfaces. Discontinuities in the value of this counter can occur at re-initialization of the management system, and at other times as indicated by the value of ifCounterDiscontinuityTime.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

lagStatusTable		1.3.6.1.4.1.10297.202.7000.1.4.1
The table of the link aggregation group
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LagStatusEntry

lagStatusEntry		1.3.6.1.4.1.10297.202.7000.1.4.1.1
The entry of the link aggregation group
Status: current	Access: not-accessible
OBJECT-TYPE
	LagStatusEntry

lagStatusIndex		1.3.6.1.4.1.10297.202.7000.1.4.1.1.1
The name of the link aggregation group
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

lagStatusName		1.3.6.1.4.1.10297.202.7000.1.4.1.1.2
The LAG port description
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lagStatusType		1.3.6.1.4.1.10297.202.7000.1.4.1.1.3
The type of the LAG. Static: The group of ports assigned to a static LAG are always active members. LACP: The group of ports assigned to dynamic LAG are candidate ports. LACP determines which candidate ports are active member ports.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	static(1), lacp(2), none(3)

lagStatusLinkState		1.3.6.1.4.1.10297.202.7000.1.4.1.1.4
LAG port link status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), notPresent(3)

lagStatusActiveMember		1.3.6.1.4.1.10297.202.7000.1.4.1.1.5
Active member ports of the LAG
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lagStatusStandbyMember		1.3.6.1.4.1.10297.202.7000.1.4.1.1.6
Inactive or candudate member ports of the LAG
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lacpInfoTable		1.3.6.1.4.1.10297.202.7000.1.4.2
The table of LACP
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LacpInfoEntry

lacpInfoEntry		1.3.6.1.4.1.10297.202.7000.1.4.2.1
The entry of LACP
Status: current	Access: not-accessible
OBJECT-TYPE
	LacpInfoEntry

lacpInfoLagIndex		1.3.6.1.4.1.10297.202.7000.1.4.2.1.1
The LACP name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lacpInfoPortIndex		1.3.6.1.4.1.10297.202.7000.1.4.2.1.2
Member port name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lacpInfoPartnerSysId		1.3.6.1.4.1.10297.202.7000.1.4.2.1.3
The system ID of link partner.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lacpInfoPnkey		1.3.6.1.4.1.10297.202.7000.1.4.2.1.4
Port key of partner
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lacpInfoAtkey		1.3.6.1.4.1.10297.202.7000.1.4.2.1.5
Port key of actor
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lacpInfoSel		1.3.6.1.4.1.10297.202.7000.1.4.2.1.6
LACP selection logic status of the port
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lacpInfoMux		1.3.6.1.4.1.10297.202.7000.1.4.2.1.7
LACP mux state machine status of the port
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lacpInfoReceiv		1.3.6.1.4.1.10297.202.7000.1.4.2.1.8
LACP receive state machine status of the port
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lacpInfoPrdtx		1.3.6.1.4.1.10297.202.7000.1.4.2.1.9
LACP periodic transmission state machine status of the port.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lacpInfoAtstat		1.3.6.1.4.1.10297.202.7000.1.4.2.1.10
The actor state field of LACP PDU description.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lacpInfoPnstat		1.3.6.1.4.1.10297.202.7000.1.4.2.1.11
The partner state field of LACP PDU description.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpClearStatistics		1.3.6.1.4.1.10297.202.7000.1.5.1
Clear the LLDP statistics
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	clear(1)

inertions		1.3.6.1.4.1.10297.202.7000.1.5.2
The number of times the complete set of infomation advertised by a partcular MAC Service Access Point(MSAP) has been inserted into tables associated with the remote systems
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

deletions		1.3.6.1.4.1.10297.202.7000.1.5.3
The number of times the complete set of infomation advertised by MSAP has been deleted from tables associated with the remote systems
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

drops		1.3.6.1.4.1.10297.202.7000.1.5.4
The number of times the complete set of information advertised by MSAP could not be entered into tables associated with the remote systems because of insufficient resources.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ageouts		1.3.6.1.4.1.10297.202.7000.1.5.5
The number of times the complete set of information advertised by MSAP has been deleted from tables associated with the remote systems because the information timeliness interval has expired.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

lldpPortStatisticsTable		1.3.6.1.4.1.10297.202.7000.1.5.6
The table of LLDP port statistics
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LLDPPortStatisticsEntry

lldpPortStatisticsEntry		1.3.6.1.4.1.10297.202.7000.1.5.6.1
The entry of LLDP port statistics
Status: current	Access: not-accessible
OBJECT-TYPE
	LLDPPortStatisticsEntry

lldpPortStatIndex		1.3.6.1.4.1.10297.202.7000.1.5.6.1.1
Interface or port number.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

lldpPortStatTotalTxFrame		1.3.6.1.4.1.10297.202.7000.1.5.6.1.2
Number of LLDP frames transmitted on the corresponding port.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

lldpPortStatTotalRxFrame		1.3.6.1.4.1.10297.202.7000.1.5.6.1.3
Number of LLDP frames received by this LLDP agent on the corresponding port, while the LLDP agent is enabled
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

lldpPortStatDiscardRxFrame		1.3.6.1.4.1.10297.202.7000.1.5.6.1.4
Number of LLDP frames discard for any reason by this LLDP agent on the corresponding port
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

lldpPortStatErrorRxFrame		1.3.6.1.4.1.10297.202.7000.1.5.6.1.5
Number of invalid LLDP frames received by the LLDP agent on the corresponding port, while the LLDP agent is enabled
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

lldpPortStatDiscardRxTlv		1.3.6.1.4.1.10297.202.7000.1.5.6.1.6
Number of TLVs LLDP frames discard for any reason by this LLDP agent on the corresponding port
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

lldpPortStatUnrecognizedRxTlv		1.3.6.1.4.1.10297.202.7000.1.5.6.1.7
Number of TLVs LLDP frames that are unrecognized while this LLDP agent is enabled
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

lldpPortStatTotalRxAgeouts		1.3.6.1.4.1.10297.202.7000.1.5.6.1.8
Number of age out LLDP frames
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

totalRx		1.3.6.1.4.1.10297.202.7000.1.6.1
IGMP snooping total Rx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

validRx		1.3.6.1.4.1.10297.202.7000.1.6.2
IGMP snooping valid Rx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

invalidRx		1.3.6.1.4.1.10297.202.7000.1.6.3
IGMP snooping invalid Rx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

otherRx		1.3.6.1.4.1.10297.202.7000.1.6.4
IGMP snooping other Rx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

leaveRx		1.3.6.1.4.1.10297.202.7000.1.6.5
IGMP snooping leave Rx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

reportRx		1.3.6.1.4.1.10297.202.7000.1.6.6
IGMP snooping report Rx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

generalQueryRx		1.3.6.1.4.1.10297.202.7000.1.6.7
IGMP snooping general query Rx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

specialGroupQueryRx		1.3.6.1.4.1.10297.202.7000.1.6.8
IGMP snooping special group query Rx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

specialGroupSourceQueryRx		1.3.6.1.4.1.10297.202.7000.1.6.9
IGMP snooping special group source query Rx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

leaveTx		1.3.6.1.4.1.10297.202.7000.1.6.10
IGMP snooping leave Tx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

reportTx		1.3.6.1.4.1.10297.202.7000.1.6.11
IGMP snooping report Tx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

generalQueryTx		1.3.6.1.4.1.10297.202.7000.1.6.12
IGMP snooping general query Tx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

specialGroupQueryTx		1.3.6.1.4.1.10297.202.7000.1.6.13
IGMP snooping special group query Tx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

specialGroupSourceQueryTx		1.3.6.1.4.1.10297.202.7000.1.6.14
IGMP snooping special group source query Tx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

clearigmpStatistics		1.3.6.1.4.1.10297.202.7000.1.6.15
Clear IGMP snooping statistics counter
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	clear(1)

mldtotalRx		1.3.6.1.4.1.10297.202.7000.1.7.1
MLD total Rx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mldvalidRx		1.3.6.1.4.1.10297.202.7000.1.7.2
MLD valid Rx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mldinvalidRx		1.3.6.1.4.1.10297.202.7000.1.7.3
MLD invalid Rx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mldotherRx		1.3.6.1.4.1.10297.202.7000.1.7.4
MLD other Rx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mldleaveRx		1.3.6.1.4.1.10297.202.7000.1.7.5
MLD leave Rx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mldreportRx		1.3.6.1.4.1.10297.202.7000.1.7.6
MLD report Rx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mldgeneralQueryRx		1.3.6.1.4.1.10297.202.7000.1.7.7
MLD general query Rx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mldspecialGroupQueryRx		1.3.6.1.4.1.10297.202.7000.1.7.8
MLD special group query Rx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mldspecialGroupSourceQueryRx		1.3.6.1.4.1.10297.202.7000.1.7.9
MLD special group source query Rx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mldleaveTx		1.3.6.1.4.1.10297.202.7000.1.7.10
MLD leave Tx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mldreportTx		1.3.6.1.4.1.10297.202.7000.1.7.11
MLD report Tx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mldgeneralQueryTx		1.3.6.1.4.1.10297.202.7000.1.7.12
MLD general query Tx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mldspecialGroupQueryTx		1.3.6.1.4.1.10297.202.7000.1.7.13
MLD special group query Tx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mldspecialGroupSourceQueryTx		1.3.6.1.4.1.10297.202.7000.1.7.14
MLD special group source query Tx counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

clearmldStatistics		1.3.6.1.4.1.10297.202.7000.1.7.15
Clear MLD statistics counter
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	clear(1)

ipSettings		1.3.6.1.4.1.10297.202.7000.2.1
OBJECT IDENTIFIER

ipv6Settings		1.3.6.1.4.1.10297.202.7000.2.2
OBJECT IDENTIFIER

managementVlan		1.3.6.1.4.1.10297.202.7000.2.3
This allows the entry of a VLAN from which a management station will be allowed to manage the device using TCP/IP (in-band via web manager or Telnet). Management stations that are on VLANs other than the one seleted here will not be able to manage the Switch. The default management VLAN is VLAN 1.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4094

systemTime		1.3.6.1.4.1.10297.202.7000.2.4
OBJECT IDENTIFIER

sfp		1.3.6.1.4.1.10297.202.7000.2.5
OBJECT IDENTIFIER

dhcpClientOpt82		1.3.6.1.4.1.10297.202.7000.2.6
OBJECT IDENTIFIER

networkPort		1.3.6.1.4.1.10297.202.7000.2.7
OBJECT IDENTIFIER

ipv4Mode		1.3.6.1.4.1.10297.202.7000.2.1.1
the mode of network connection Static: Enable static IP address. DHCP: Enable DHCP to obtain IP information from a DHCP server on the network.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	static(1), dhcp(2)

ipv4Address		1.3.6.1.4.1.10297.202.7000.2.1.2
If static mode is enabled, enter IP address in this field.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

ipv4SubnetMask		1.3.6.1.4.1.10297.202.7000.2.1.3
If static mode is enabled, enter subnet mask in this field.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

ipv4Gateway		1.3.6.1.4.1.10297.202.7000.2.1.4
If static mode is enabled, enter gateway address in this field.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

ipv4DnsServer1		1.3.6.1.4.1.10297.202.7000.2.1.5
If static mode is enabled, enter primary DNS server address in this field
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

ipv4DnsServer2		1.3.6.1.4.1.10297.202.7000.2.1.6
If static mode is enabled, enter secondary DNS server address in this field
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

interfaceIpv4Table		1.3.6.1.4.1.10297.202.7000.2.1.7
The table of interface IP address
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		InterfaceIpv4Entry

interfaceIpv4Entry		1.3.6.1.4.1.10297.202.7000.2.1.7.1
The entry of interface IP address
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceIpv4Entry

interfaceIpv4Index		1.3.6.1.4.1.10297.202.7000.2.1.7.1.1
The index of interface IPv4 table
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..32

interfaceIpv4Vlan		1.3.6.1.4.1.10297.202.7000.2.1.7.1.2
The VLAN ID of interface IPv4 table
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

interfaceIpv4Mode		1.3.6.1.4.1.10297.202.7000.2.1.7.1.3
the mode of network connection Static: Enable static IP address. DHCP: Enable DHCP to obtain IP information from a DHCP server on the network.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	static(1), dhcp(2)

interfaceIpv4Address		1.3.6.1.4.1.10297.202.7000.2.1.7.1.4
If static mode is enabled, enter IP address in this field.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

interfaceIpv4SubnetMask		1.3.6.1.4.1.10297.202.7000.2.1.7.1.5
If static mode is enabled, enter subnet mask in this field.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

interfaceIpv4Gateway		1.3.6.1.4.1.10297.202.7000.2.1.7.1.6
If static mode is enabled, enter gateway address in this field.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

interCurrIpv4DhcpState		1.3.6.1.4.1.10297.202.7000.2.1.7.1.7
The current status of IPv4 DHCP.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

interCurrIpv4Address		1.3.6.1.4.1.10297.202.7000.2.1.7.1.8
The current IPv4 address
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

interCurrIpv4SubnetMask		1.3.6.1.4.1.10297.202.7000.2.1.7.1.9
The current IPv4 subnet mask
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

interCurrIpv4Gateway		1.3.6.1.4.1.10297.202.7000.2.1.7.1.10
The current IPv4 gateway.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

autoConfiguration		1.3.6.1.4.1.10297.202.7000.2.2.1
IPv6 Auto Configuration state.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ipv6Address		1.3.6.1.4.1.10297.202.7000.2.2.2
If auto configuration mode is disabled, enter IPv6 address in this field.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

ipv6SubnetMask		1.3.6.1.4.1.10297.202.7000.2.2.3
If auto configuration mode is disabled, enter IPv6 submask in this field.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..128

ipv6Gateway		1.3.6.1.4.1.10297.202.7000.2.2.4
If auto configuration mode is disabled, enter IPv6 gateway address in this field.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

dhcpv6Client		1.3.6.1.4.1.10297.202.7000.2.2.5
DHCPv6 client state
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ipv6InUseTable		1.3.6.1.4.1.10297.202.7000.2.2.6
The table of in-use IPv6 address
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IPv6InUseEntry

ipv6InUseEntry		1.3.6.1.4.1.10297.202.7000.2.2.6.1
The entry of in-use IPv6 address
Status: current	Access: not-accessible
OBJECT-TYPE
	IPv6InUseEntry

ipv6InUseIndex		1.3.6.1.4.1.10297.202.7000.2.2.6.1.1
The current use IPv6 submask
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..32

ipv6InUseAddress		1.3.6.1.4.1.10297.202.7000.2.2.6.1.2
The current use IPv6 address
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

ipv6InUseSubnetMask		1.3.6.1.4.1.10297.202.7000.2.2.6.1.3
The current use IPv6 submask
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

ipv6InUseRouter		1.3.6.1.4.1.10297.202.7000.2.2.7
The current use IPv6 router address
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

dhcpv6DUID		1.3.6.1.4.1.10297.202.7000.2.2.8
The DHCPv6 DUID
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

dhcpv6IPAddress		1.3.6.1.4.1.10297.202.7000.2.2.9
The DHCPv6 IP address
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

systemTimeSetting		1.3.6.1.4.1.10297.202.7000.2.4.1
OBJECT IDENTIFIER

enableSNTP		1.3.6.1.4.1.10297.202.7000.2.4.1.1
enable or disable using SNTP server.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

manualTime		1.3.6.1.4.1.10297.202.7000.2.4.1.2
OBJECT IDENTIFIER

year		1.3.6.1.4.1.10297.202.7000.2.4.1.2.1
The year of the switch
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	2000..2035

month		1.3.6.1.4.1.10297.202.7000.2.4.1.2.2
The month of the switch
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..12

day		1.3.6.1.4.1.10297.202.7000.2.4.1.2.3
The day of the switch
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..31

hours		1.3.6.1.4.1.10297.202.7000.2.4.1.2.4
The hour of the switch
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..23

minutes		1.3.6.1.4.1.10297.202.7000.2.4.1.2.5
The minutes of the switch
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..59

seconds		1.3.6.1.4.1.10297.202.7000.2.4.1.2.6
The second of the switch
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..59

timeZone		1.3.6.1.4.1.10297.202.7000.2.4.1.3
The UTC Timezone of the switch.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), gmtminus1200-International-Date-Line-West(1), gmtminus1100-MidwayIsland-Samoa(2), gmtminus1000-Hawaii(3), gmtminus0900-Alaska(4), gmtminus0800-Pacific-Time-US-and-Canada(5), gmtminus0800-Tijuana-Baja-California(6), gmtminus0700-Arizona(7), gmtminus0700-Chihuahua-La-Paz-Mazatlan-New(8), gmtminus0700-Chihuahua-La-Paz-Mazatlan-Old(9), gmtminus0700-Mountain-Time-US-and-Canada(10), gmtminus0600-Central-America(11), gmtminus0600-Central-Time-US-and-Canada(12), gmtminus0600-Guadalajara-Mexico-City-Monterrey-New(13), gmtminus0600-Guadalajara-Mexico-City-Monterrey-Old(14), gmtminus0600-Saskatchewan(15), gmtminus0500-Bogota-Lima-Quito-Rio-Branco(16), gmtminus0500-Eastern-Time-US-and-Canada(17), gmtminus0500-Indiana-East(18), gmtminus0430-Caracas(19), gmtminus0400-Atlantic-Time-Canada(20), gmtminus0400-La-Paz(21), gmtminus0400-Manaus(22), gmtminus0400-Santiago(23), gmtminus0330-Newfoundland(24), gmtminus0300-Brasilia(25), gmtminus0300-Buenos-Aires(26), gmtminus0300-Georgetown(27), gmtminus0300-Greenland(28), gmtminus0300-Montevideo(29), gmtminus0200-Mid-Atlantic(30), gmtminus0100-Azores(31), gmtminus0100-Cape-Verde-Is(32), gmt-Casablanca(33), gmt-Greenwich-Mean-Time-Dublin-Edinburgh-Lisbon-London(34), gmt-Monrovia-Reykjavik(35), gmtplus0100-Amsterdam-Berlin-Bern-Rome-Stockholm-Vienna(36), gmtplus0100-Belgrade-Bratislava-Budapest-Ljubljana-Prague(37), gmtplus0100-Brussels-Copenhagen-Madrid-Paris(38), gmtplus0100-Sarajevo-Skopje-Warsaw-Zagreb(39), gmtplus0100-West-Central-Africa(40), gmtplus0200-Amman(41), gmtplus0200-Athens-Bucharest-Istanbul(42), gmtplus0200-Beirut(43), gmtplus0200-Cairo(44), gmtplus0200-Harare-Pretoria(45), gmtplus0200-Helsinki-Kyiv-Riga-Sofia-Tallinn-Vilnius(46), gmtplus0200-Jerusalem(47), gmtplus0200-Minsk(48), gmtplus0200-Windhoek(49), gmtplus0300-Baghdad(50), gmtplus0300-Kuwait-Riyadh(51), gmtplus0300-Moscow-St-Petersburg-Volgograd(52), gmtplus0300-Nairobi(53), gmtplus0300-Tbilisi(54), gmtplus0330-Tehran(55), gmtplus0400-Abu-Dhabi-Muscat(56), gmtplus0400-Baku(57), gmtplus0400-Caucasus-Standard-Time(58), gmtplus0400-Port-Louis(59), gmtplus0400-Yerevan(60), gmtplus0430-Kabul(61), gmtplus0500-Ekaterinburg(62), gmtplus0500-Islamabad-Karachi(63), gmtplus0500-Tashkent(64), gmtplus0530-Chennai-Kolkata-Mumbai-New-Delhi(65), gmtplus0530-Sri-Jayawardenepura(66), gmtplus0545-Kathmandu(67), gmtplus0600-Almaty-Novosibirsk(68), gmtplus0600-Astana-Dhaka(69), gmtplus0630-Yangon-Rangoon(70), gmtplus0700-Bangkok-Hanoi-Jakarta(71), gmtplus0700-Krasnoyarsk(72), gmtplus0800-Beijing-Chongqing-Hong-Kong-Urumqi(73), gmtplus0800-Irkutsk-Ulaan-Bataar(74), gmtplus0800-Kuala-Lumpur-Singapore(75), gmtplus0800-Perth(76), gmtplus0800-Taipei(77), gmtplus0900-Osaka-Sapporo-Tokyo(78), gmtplus0900-Seoul(79), gmtplus0900-Yakutsk(80), gmtplus0930-Adelaide(81), gmtplus0930-Darwin(82), gmtplus1000-Brisbane(83), gmtplus1000-Canberra-Melbourne-Sydney(84), gmtplus1000-Guam-Port-Moresby(85), gmtplus1000-Hobart(86), gmtplus1000-Vladivostok(87), gmtplus1100-Magadan-Solomon-Is-New-Caledonia(88), gmtplus1200-Auckland-Wellington(89), gmtplus1200-Fiji-Kamchatka-Marshall-Is(90), gmtplus1300-Nuku-alofa(91)

daylightSaving		1.3.6.1.4.1.10297.202.7000.2.4.1.4
the mode of daylight saving time. Disable: Disable daylight saving time. Recurring: Using recurring mode of daylight saving time Non-Recurring: Using non-recurring mode of daylight saving time USA: Using daylight saving time in the United States that starts on the second Sunday of March and ends on the first Sunday of November European: daylight saving time in the Europe that starts on the last Sunday of March and ends on the last Sunday of November
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), recurring(2), no-recurring(3), usa(4), european(5)

daylightSavingOffset		1.3.6.1.4.1.10297.202.7000.2.4.1.5
Specify the adjust offset of daylight saving time
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..1440

recurringFrom		1.3.6.1.4.1.10297.202.7000.2.4.1.6
OBJECT IDENTIFIER

recFromDay		1.3.6.1.4.1.10297.202.7000.2.4.1.6.1
The starting day of recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..7

recFromWeek		1.3.6.1.4.1.10297.202.7000.2.4.1.6.2
The starting week of recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..5

recFromMonth		1.3.6.1.4.1.10297.202.7000.2.4.1.6.3
The starting month of recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..12

recFromHours		1.3.6.1.4.1.10297.202.7000.2.4.1.6.4
The starting hour of recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..23

recFromMinutes		1.3.6.1.4.1.10297.202.7000.2.4.1.6.5
The starting minutes of recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..59

recurringTo		1.3.6.1.4.1.10297.202.7000.2.4.1.7
OBJECT IDENTIFIER

recToDay		1.3.6.1.4.1.10297.202.7000.2.4.1.7.1
The ending day of recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..7

recToWeek		1.3.6.1.4.1.10297.202.7000.2.4.1.7.2
The ending week of recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..5

recToMonth		1.3.6.1.4.1.10297.202.7000.2.4.1.7.3
The ending month of recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..12

recToHours		1.3.6.1.4.1.10297.202.7000.2.4.1.7.4
The ending hour of recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..23

recToMinutes		1.3.6.1.4.1.10297.202.7000.2.4.1.7.5
The ending minute of recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..59

nonRecurringFrom		1.3.6.1.4.1.10297.202.7000.2.4.1.8
OBJECT IDENTIFIER

nonRecFromYear		1.3.6.1.4.1.10297.202.7000.2.4.1.8.1
The starting year of non-recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	2000..2037

nonRecFromMonth		1.3.6.1.4.1.10297.202.7000.2.4.1.8.2
The starting month of non-recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..12

nonRecFromDay		1.3.6.1.4.1.10297.202.7000.2.4.1.8.3
The starting day of non-recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..31

nonRecFromHours		1.3.6.1.4.1.10297.202.7000.2.4.1.8.4
The starting hour of non-recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..23

nonRecFromMinutes		1.3.6.1.4.1.10297.202.7000.2.4.1.8.5
The starting minute of non-recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..59

nonRecurringTo		1.3.6.1.4.1.10297.202.7000.2.4.1.9
OBJECT IDENTIFIER

nonRecToYear		1.3.6.1.4.1.10297.202.7000.2.4.1.9.1
The ending year of non-recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	2000..2037

nonRecToMonth		1.3.6.1.4.1.10297.202.7000.2.4.1.9.2
The ending month of non-recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..12

nonRecToDay		1.3.6.1.4.1.10297.202.7000.2.4.1.9.3
The ending day of non-recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..31

nonRecToHours		1.3.6.1.4.1.10297.202.7000.2.4.1.9.4
The ending hour of non-recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..23

nonRecToMinutes		1.3.6.1.4.1.10297.202.7000.2.4.1.9.5
The ending minute of non-recurring daylight saving time.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..59

serverAddress		1.3.6.1.4.1.10297.202.7000.2.4.1.10
IP address or hostname of time server
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

serverPort		1.3.6.1.4.1.10297.202.7000.2.4.1.11
Time server port number
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

systemTimeStatus		1.3.6.1.4.1.10297.202.7000.2.4.1.12
If user set system time with SNMP, the value sould not apply to switch. They need to set active(1) to apply into switch
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), notInService(2)

systemTimeInfo		1.3.6.1.4.1.10297.202.7000.2.4.2
OBJECT IDENTIFIER

currentDateTime		1.3.6.1.4.1.10297.202.7000.2.4.2.1
Current Date and Time on the device.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

currentSNTP		1.3.6.1.4.1.10297.202.7000.2.4.2.2
The status of SNTP server.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

currentSNTPServerAddr		1.3.6.1.4.1.10297.202.7000.2.4.2.3
The IP address or hostname of SNTP server.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

currentSNTPServerPort		1.3.6.1.4.1.10297.202.7000.2.4.2.4
The port number of SNTP server.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

currentTimeZone		1.3.6.1.4.1.10297.202.7000.2.4.2.5
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

currentDaylightSavingStatus		1.3.6.1.4.1.10297.202.7000.2.4.2.6
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

currentDaylightSavingOffset		1.3.6.1.4.1.10297.202.7000.2.4.2.7
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

currentDaylightSavingFrom		1.3.6.1.4.1.10297.202.7000.2.4.2.8
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

currentDaylightSavingTo		1.3.6.1.4.1.10297.202.7000.2.4.2.9
Tok_String
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sfpSerialInfoTable		1.3.6.1.4.1.10297.202.7000.2.5.1
The table of SFP serial info.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SFPSerialInfoEntry

sfpSerialInfoEntry		1.3.6.1.4.1.10297.202.7000.2.5.1.1
The entry of SFP serial info.
Status: current	Access: not-accessible
OBJECT-TYPE
	SFPSerialInfoEntry

sfpPortIndex		1.3.6.1.4.1.10297.202.7000.2.5.1.1.1
The index of SFP serial info.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sfpConnector		1.3.6.1.4.1.10297.202.7000.2.5.1.1.2
The SFP connector
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sfpSpeed		1.3.6.1.4.1.10297.202.7000.2.5.1.1.3
The SFP speed
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sfpVendorName		1.3.6.1.4.1.10297.202.7000.2.5.1.1.4
The SFP vender name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sfpVendorPn		1.3.6.1.4.1.10297.202.7000.2.5.1.1.6
The SFP vendor product number
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

spfVendorRev		1.3.6.1.4.1.10297.202.7000.2.5.1.1.7
The SFP vender revision
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sfpVendorSn		1.3.6.1.4.1.10297.202.7000.2.5.1.1.8
The SFP vendor serial number
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sfpDateCode		1.3.6.1.4.1.10297.202.7000.2.5.1.1.9
The SFP data code
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sfpDMIInfoTable		1.3.6.1.4.1.10297.202.7000.2.5.2
The table of SFP DMI info.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SFPDMIInfoEntry

sfpDMIInfoEntry		1.3.6.1.4.1.10297.202.7000.2.5.2.1
The entry of SFP DMI info.
Status: current	Access: not-accessible
OBJECT-TYPE
	SFPDMIInfoEntry

sfpDMIPortIndex		1.3.6.1.4.1.10297.202.7000.2.5.2.1.1
The index of SFP DMI info.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sfpDMITemperature		1.3.6.1.4.1.10297.202.7000.2.5.2.1.2
The SFP DMI temperature
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sfpDMIVoltage		1.3.6.1.4.1.10297.202.7000.2.5.2.1.3
The SFP DMI voltage
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sfpDMITxBias		1.3.6.1.4.1.10297.202.7000.2.5.2.1.4
The SFP DMI Tx bias
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sfpDMITxPower		1.3.6.1.4.1.10297.202.7000.2.5.2.1.5
The SFP DMI Tx power
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sfpDMIRxPower		1.3.6.1.4.1.10297.202.7000.2.5.2.1.6
The SFP DMI Rx power
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

ddmDiagnosticAlarm		1.3.6.1.4.1.10297.202.7000.2.5.3
The DDM diagnostic alarm setting
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disabled(1), syslog(2), email(3), snmp(4)

sfpDMIAlarmInfoTable		1.3.6.1.4.1.10297.202.7000.2.5.4
The table of SFP DMI alarm info.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SFPDMIAlarmInfoEntry

sfpDMIAlarmInfoEntry		1.3.6.1.4.1.10297.202.7000.2.5.4.1
The entry of SFP DMI alarm info.
Status: current	Access: not-accessible
OBJECT-TYPE
	SFPDMIAlarmInfoEntry

sfpDMIAlarmPortIndex		1.3.6.1.4.1.10297.202.7000.2.5.4.1.1
The index of SFP DMI alarm info.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sfpDMITempHighAlarmState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.2
The state of SFP DMI temperature high alarm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMITempHighAlarmValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.3
The value of SFP DMI temperature high alarm. The value range is 127 Degrees C ~ -127 Degrees C
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sfpDMITempHighWarnState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.4
The state of SFP DMI temperature high warning
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMITempHighWarnValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.5
The value of SFP DMI temperature high warning. The value range is 127 Degrees C ~ -127 Degrees C
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sfpDMITempLowAlarmState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.6
The state of SFP DMI temperature low alarm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMITempLowAlarmValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.7
The value of SFP DMI temperature low alarm. The value range is 127 Degrees C ~ -127 Degrees C
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sfpDMITempLowWarnState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.8
The state of SFP DMI temperature low warning
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMITempLowWarnValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.9
The value of SFP DMI temperature low warning. The value range is 127 Degrees C ~ -127 Degrees C
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sfpDMIVoltageHighAlarmState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.10
The state of SFP DMI voltage high alarm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMIVoltageHighAlarmValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.11
The value of SFP DMI voltage high alarm. The value range is 0.001~6V
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sfpDMIVoltageHighWarnState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.12
The state of SFP DMI voltage high warning
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMIVoltageHighWarnValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.13
The value of SFP DMI voltage high warning. The value range is 0.001~6V
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sfpDMIVoltageLowAlarmState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.14
The state of SFP DMI voltage low alarm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMIVoltageLowAlarmValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.15
The value of SFP DMI voltage low alarm. The value range is 0.001~6V
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sfpDMIVoltageLowWarnState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.16
The state of SFP DMI voltage low warning
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMIVoltageLowWarnValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.17
The value of SFP DMI voltage low warning. The value range is 0.001~6V
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sfpDMITxBasisHighAlarmState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.18
The state of SFP DMI TX Basis high alarm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMITxBasisHighAlarmValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.19
The value of SFP DMI TX Basis high alarm. The value range is 1~131mA
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sfpDMITxBasisHighWarnState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.20
The state of SFP DMI TX Basis high warning
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMITxBasisHighWarnValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.21
The value of SFP DMI TX Basis high warning. The value range is 1~131mA
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sfpDMITxBasisLowAlarmState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.22
The state of SFP DMI TX Basis low alarm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMITxBasisLowAlarmValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.23
The value of SFP DMI TX Basis low alarm. The value range is 1~131mA
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sfpDMITxBasisLowWarnState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.24
The state of SFP DMI TX Basis low warning
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMITxBasisLowWarnValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.25
The value of SFP DMI TX Basis low warning. The value range is 1~131mA
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sfpDMITxPowerHighAlarmState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.26
The state of SFP DMI TX power high alarm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMITxPowerHighAlarmValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.27
The value of SFP DMI TX power high alarm. The value range is 8~-39dbm
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sfpDMITxPowerHighWarnState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.28
The state of SFP DMI TX power high warning
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMITxPowerHighWarnValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.29
The value of SFP DMI TX power high warning. The value range is 8~-39dbm
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sfpDMITxPowerLowAlarmState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.30
The state of SFP DMI TX power low alarm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMITxPowerLowAlarmValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.31
The value of SFP DMI TX power low alarm. The value range is 8~-39dbm
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sfpDMITxPowerLowWarnState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.32
The state of SFP DMI TX power low warning
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMITxPowerLowWarnValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.33
The value of SFP DMI TX power low warning. The value range is 8~-39dbm
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sfpDMIRxPowerHighAlarmState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.34
The state of SFP DMI RX power high alarm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMIRxPowerHighAlarmValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.35
The value of SFP DMI RX power high alarm. The value range is 8~-39dbm
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sfpDMIRxPowerHighWarnState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.36
The state of SFP DMI RX power high warning
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMIRxPowerHighWarnValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.37
The value of SFP DMI RX power high warning. The value range is 8~-39dbm
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sfpDMIRxPowerLowAlarmState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.38
The state of SFP DMI RX power low alarm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMIRxPowerLowAlarmValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.39
The value of SFP DMI RX power low alarm. The value range is 8~-39dbm
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sfpDMIRxPowerLowWarnState		1.3.6.1.4.1.10297.202.7000.2.5.4.1.40
The state of SFP DMI RX power low warning
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

sfpDMIRxPowerLowWarnValue		1.3.6.1.4.1.10297.202.7000.2.5.4.1.41
The value of SFP DMI RX power low warning. The value range is 8~-39dbm
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

dhcpClientOpt82Status		1.3.6.1.4.1.10297.202.7000.2.6.1
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

dhcpClientOpt82CircuitIDFormat		1.3.6.1.4.1.10297.202.7000.2.6.2
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	string(1), hex(2), userDefined(3)

dhcpClientOpt82CircuitIDString		1.3.6.1.4.1.10297.202.7000.2.6.3
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

dhcpClientOpt82CircuitIDHex		1.3.6.1.4.1.10297.202.7000.2.6.4
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

dhcpClientOpt82CircuitIDUserDefine		1.3.6.1.4.1.10297.202.7000.2.6.5
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

dhcpClientOpt82RemoteIDFormat		1.3.6.1.4.1.10297.202.7000.2.6.6
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	string(1), hex(2), userDefined(3)

dhcpClientOpt82RemoteIDString		1.3.6.1.4.1.10297.202.7000.2.6.7
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

dhcpClientOpt82RemoteIDHex		1.3.6.1.4.1.10297.202.7000.2.6.8
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

dhcpClientOpt82RemoteIDUserDefine		1.3.6.1.4.1.10297.202.7000.2.6.9
Tok_String
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

httpNetworkPort		1.3.6.1.4.1.10297.202.7000.2.7.1
The network port of http.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

httpsNetworkPort		1.3.6.1.4.1.10297.202.7000.2.7.2
The network port of https.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

telnetNetworkPort		1.3.6.1.4.1.10297.202.7000.2.7.3
The network port of telnet.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

sshNetworkPort		1.3.6.1.4.1.10297.202.7000.2.7.4
The network port of ssh.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

portSetting		1.3.6.1.4.1.10297.202.7000.3.1
OBJECT IDENTIFIER

mirror		1.3.6.1.4.1.10297.202.7000.3.2
OBJECT IDENTIFIER

lag		1.3.6.1.4.1.10297.202.7000.3.3
OBJECT IDENTIFIER

vlan		1.3.6.1.4.1.10297.202.7000.3.4
OBJECT IDENTIFIER

eee		1.3.6.1.4.1.10297.202.7000.3.5
OBJECT IDENTIFIER

multicast		1.3.6.1.4.1.10297.202.7000.3.6
OBJECT IDENTIFIER

jamboFrame		1.3.6.1.4.1.10297.202.7000.3.7
OBJECT IDENTIFIER

stp		1.3.6.1.4.1.10297.202.7000.3.8
OBJECT IDENTIFIER

qinqVlan		1.3.6.1.4.1.10297.202.7000.3.9
OBJECT IDENTIFIER

garp		1.3.6.1.4.1.10297.202.7000.3.10
OBJECT IDENTIFIER

gvrp		1.3.6.1.4.1.10297.202.7000.3.11
OBJECT IDENTIFIER

xRingElite		1.3.6.1.4.1.10297.202.7000.3.12
OBJECT IDENTIFIER

loopback		1.3.6.1.4.1.10297.202.7000.3.13
OBJECT IDENTIFIER

xRingPro		1.3.6.1.4.1.10297.202.7000.3.14
OBJECT IDENTIFIER

gmrp		1.3.6.1.4.1.10297.202.7000.3.15
OBJECT IDENTIFIER

erps		1.3.6.1.4.1.10297.202.7000.3.16
OBJECT IDENTIFIER

portSettingTable		1.3.6.1.4.1.10297.202.7000.3.1.1
The table of port setting.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PortSettingEntry

portSettingEntry		1.3.6.1.4.1.10297.202.7000.3.1.1.1
The entry of port setting.
Status: current	Access: not-accessible
OBJECT-TYPE
	PortSettingEntry

portSettingIndex		1.3.6.1.4.1.10297.202.7000.3.1.1.1.1
The index of port setting.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

description		1.3.6.1.4.1.10297.202.7000.3.1.1.1.2
Port description
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

enableState		1.3.6.1.4.1.10297.202.7000.3.1.1.1.3
Port admin state
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

linkStatus		1.3.6.1.4.1.10297.202.7000.3.1.1.1.4
Port link status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

speed		1.3.6.1.4.1.10297.202.7000.3.1.1.1.5
Port speed capabilities
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	auto(1), auto-10M(2), auto-100M(3), auto-1000M(4), auto-10M-100M(5), fixed-10M(6), fixed-100M(7), fixed-1000M(8)

duplex		1.3.6.1.4.1.10297.202.7000.3.1.1.1.6
Port duplex capabilities
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	auto(1), half(2), full(3)

flowControlConfig		1.3.6.1.4.1.10297.202.7000.3.1.1.1.7
Port flow control setting
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

flowControlStatus		1.3.6.1.4.1.10297.202.7000.3.1.1.1.8
Port flow control status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mirrorTable		1.3.6.1.4.1.10297.202.7000.3.2.1
The table of mirror funciton
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MirrorEntry

mirrorEntry		1.3.6.1.4.1.10297.202.7000.3.2.1.1
The entry of mirror funciton
Status: current	Access: not-accessible
OBJECT-TYPE
	MirrorEntry

sessionId		1.3.6.1.4.1.10297.202.7000.3.2.1.1.1
Mirror session ID
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4

monitorSessionState		1.3.6.1.4.1.10297.202.7000.3.2.1.1.2
Mirror session state
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	port-based(1), disable(2)

destinationPort		1.3.6.1.4.1.10297.202.7000.3.2.1.1.3
Mirror session destination port
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

ingressState		1.3.6.1.4.1.10297.202.7000.3.2.1.1.4
Destination port ingress state
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

sourceTxPort		1.3.6.1.4.1.10297.202.7000.3.2.1.1.5
Mirror session source tx ports only select portbased-enabled state.
Status: current	Access: read-write
OBJECT-TYPE
	BITS	port1(0), port2(1), port3(2), port4(3), port5(4), port6(5), port7(6), port8(7), port9(8), port10(9), port11(10), port12(11), port13(12), port14(13), port15(14), port16(15), port17(16), port18(17), port19(18), port20(19), port21(20), port22(21), port23(22), port24(23), port25(24), port26(25), port27(26), port28(27), port29(28), port30(29), port31(30), port32(31)

sourceRxPort		1.3.6.1.4.1.10297.202.7000.3.2.1.1.6
Mirror session source rx ports only select portbased-enabled state
Status: current	Access: read-write
OBJECT-TYPE
	BITS	port1(0), port2(1), port3(2), port4(3), port5(4), port6(5), port7(6), port8(7), port9(8), port10(9), port11(10), port12(11), port13(12), port14(13), port15(14), port16(15), port17(16), port18(17), port19(18), port20(19), port21(20), port22(21), port23(22), port24(23), port25(24), port26(25), port27(26), port28(27), port29(28), port30(29), port31(30), port32(31)

loadBalanceAlgorithm		1.3.6.1.4.1.10297.202.7000.3.3.1
LAG load balance distribution algorithm. MAC Address: Based on source and destination MAC address for all packets IP/MAC Address: Based on source and destination IP addresses for IP packet, and source and destination MAC address for non-IP packets. Source Port: Based on Source Port for all packets.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	mac-address(1), ip-mac-address(2), source-port(3)

lagManagementTable		1.3.6.1.4.1.10297.202.7000.3.3.2
The table of LAG management
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LagManagementEntry

lagManagementEntry		1.3.6.1.4.1.10297.202.7000.3.3.2.1
The entry of LAG management
Status: current	Access: not-accessible
OBJECT-TYPE
	LagManagementEntry

lagIndex		1.3.6.1.4.1.10297.202.7000.3.3.2.1.1
The index of LAG management
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

lagName		1.3.6.1.4.1.10297.202.7000.3.3.2.1.2
LAG port name
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

lagType		1.3.6.1.4.1.10297.202.7000.3.3.2.1.3
the type of the LAG Static: The group of ports assigned to a static LAG are always active members. LACP: The group of ports assigned to dynamic LAG are candidate ports. LACP determines which candidate ports are active member ports.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	static(1), lacp(2), none(3)

lagPorts		1.3.6.1.4.1.10297.202.7000.3.3.2.1.4
the trunk member ports in this field
Status: current	Access: read-write
OBJECT-TYPE
	BITS	port1(0), port2(1), port3(2), port4(3), port5(4), port6(5), port7(6), port8(7), port9(8), port10(9), port11(10), port12(11), port13(12), port14(13), port15(14), port16(15), port17(16), port18(17), port19(18), port20(19), port21(20), port22(21), port23(22), port24(23), port25(24), port26(25), port27(26), port28(27), port29(28), port30(29), port31(30), port32(31)

lagLinkState		1.3.6.1.4.1.10297.202.7000.3.3.2.1.5
LAG port link status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), not-present(3)

lagActiveMember		1.3.6.1.4.1.10297.202.7000.3.3.2.1.6
Active member ports of the LAG
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lagStandbyMember		1.3.6.1.4.1.10297.202.7000.3.3.2.1.7
Inactive or candidate member ports of the LAG
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lagPortTable		1.3.6.1.4.1.10297.202.7000.3.3.3
The table of LAG port
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LagPortEntry

lagPortEntry		1.3.6.1.4.1.10297.202.7000.3.3.3.1
The entry of LAG port
Status: current	Access: not-accessible
OBJECT-TYPE
	LagPortEntry

lagPortIndex		1.3.6.1.4.1.10297.202.7000.3.3.3.1.1
The index of LAG port
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

lagPortDescription		1.3.6.1.4.1.10297.202.7000.3.3.3.1.2
The description of the LAG port
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lagPortType		1.3.6.1.4.1.10297.202.7000.3.3.3.1.3
Member port media type
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lagPortEnableState		1.3.6.1.4.1.10297.202.7000.3.3.3.1.4
LAG port admin state
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lagPortLinkStatus		1.3.6.1.4.1.10297.202.7000.3.3.3.1.5
LAG port link status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

lagPortSpeed		1.3.6.1.4.1.10297.202.7000.3.3.3.1.6
Current LAG port speed
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	auto(1), auto-10M(2), auto-100M(3), auto-1000M(4), auto-10M-100M(5), fixed-10M(6), fixed-100M(7), fixed-1000M(8)

lagPortDuplex		1.3.6.1.4.1.10297.202.7000.3.3.3.1.7
Current LAG port duplex
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	auto(1), half(2), full(3)

lagPortFlowCtrlConfig		1.3.6.1.4.1.10297.202.7000.3.3.3.1.8
LAG port flow control configuration
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lagPortFlowCtrlStatus		1.3.6.1.4.1.10297.202.7000.3.3.3.1.9
Current LAG port flow control state
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lacpSystemPriority		1.3.6.1.4.1.10297.202.7000.3.3.4
Configure the system priority of LACP
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

lacpPortTable		1.3.6.1.4.1.10297.202.7000.3.3.5
The table of LACP Port
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LacpPortEntry

lacpPortEntry		1.3.6.1.4.1.10297.202.7000.3.3.5.1
The entry of LACP Port
Status: current	Access: not-accessible
OBJECT-TYPE
	LacpPortEntry

lacpPortIndex		1.3.6.1.4.1.10297.202.7000.3.3.5.1.1
The index of LACP Port
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

lacpPriority		1.3.6.1.4.1.10297.202.7000.3.3.5.1.2
LACP priority of the port
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

lacpTimeout		1.3.6.1.4.1.10297.202.7000.3.3.5.1.3
The periodic transmissions of LACP PDUs Long: Transmit LACP PDU with slow periodic (30s). Short: Transmit LACPP DU with fast periodic (1s).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	long(1), short(2)

lacpPortMode		1.3.6.1.4.1.10297.202.7000.3.3.5.1.4
LACP mode of the port
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), passive(2)

vlanTable		1.3.6.1.4.1.10297.202.7000.3.4.1
The table of VLAN
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		VlanEntry

vlanEntry		1.3.6.1.4.1.10297.202.7000.3.4.1.1
The entry of VLAN
Status: current	Access: not-accessible
OBJECT-TYPE
	VlanEntry

vlanIndex		1.3.6.1.4.1.10297.202.7000.3.4.1.1.1
The index of VLAN
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4094

vlanId		1.3.6.1.4.1.10297.202.7000.3.4.1.1.2
The VLAN ID
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4094

vlanNamePrefix		1.3.6.1.4.1.10297.202.7000.3.4.1.1.3
The prefix string of the VLAN name
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

vlanType		1.3.6.1.4.1.10297.202.7000.3.4.1.1.4
The VLAN type
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	default(1), static(2), dyanmic(3)

vlanRowStatus		1.3.6.1.4.1.10297.202.7000.3.4.1.1.99
User can use createAndWait(5) to create new entry. After setup the value, user use active(1) to set into switch. User can use destory to delete(6) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	active(1), notInService(2), createAndWait(5), destory(6)

vlanInterfaceTable		1.3.6.1.4.1.10297.202.7000.3.4.2
The table of the VLN inetrface
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		VlanInterfaceEntry

vlanInterfaceEntry		1.3.6.1.4.1.10297.202.7000.3.4.2.1
The entry of the VLN inetrface
Status: current	Access: not-accessible
OBJECT-TYPE
	VlanInterfaceEntry

vlanPortIndex		1.3.6.1.4.1.10297.202.7000.3.4.2.1.1
The port index of the VLAN interface
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

vlanInterfaceVlanMode		1.3.6.1.4.1.10297.202.7000.3.4.2.1.2
VLAN mode for the interface. Hybrid: support all functions as defined in IEEE 802.1Q Access: Accepts only untagged frames and join an untagged VLAN Trunk: An ubtagged member of one VLAN at most, and is a tagged member of zero or more VLANs. Tunnel: Port-based Q-in-Q mode
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	hybrid(1), access(2), trunk(3), tunnel(4)

vlanPvid		1.3.6.1.4.1.10297.202.7000.3.4.2.1.3
The port-based VLAN ID, It only available with Hybrid and Trunk mode.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4094

vlanAcceptedType		1.3.6.1.4.1.10297.202.7000.3.4.2.1.4
the acceptable-frame-type of the specified interfaces. It is only available with Hybrid mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	all(1), tag-only(2), untag-only(3)

vlanIngressFiltering		1.3.6.1.4.1.10297.202.7000.3.4.2.1.5
the status of ingress filtering. It is only available with Hybrid mode.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disbale(2)

portToVlanTable		1.3.6.1.4.1.10297.202.7000.3.4.3
The table of Port to VLAN
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PortToVlanEntry

portToVlanEntry		1.3.6.1.4.1.10297.202.7000.3.4.3.1
The entry of Port to VLAN
Status: current	Access: not-accessible
OBJECT-TYPE
	PortToVlanEntry

portToVlanVlanIndex		1.3.6.1.4.1.10297.202.7000.3.4.3.1.1
The index of Port to VLAN
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

portToVlanPortIndex		1.3.6.1.4.1.10297.202.7000.3.4.3.1.2
The port index of Port to VLAN
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

portToVlanVlanId		1.3.6.1.4.1.10297.202.7000.3.4.3.1.3
VLAN ID
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

portToVlanInterfaceVlanMode		1.3.6.1.4.1.10297.202.7000.3.4.3.1.4
Display the interface VLAN mode of this port
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	hybrid(1), access(2), trunk(3), tunnel(4)

portToVlanMembership		1.3.6.1.4.1.10297.202.7000.3.4.3.1.5
the membership for this port with the specified VLAN ID. Forbidden: Specify the port is forbidden in the VLAN. Excluded: Specify the port is excluded in the VLAN. Tagged: Specify the port is tagged in the VLAN. Untagged: Specify the port is untagged in the VLAN.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	forbidden(1), exclued(2), tagged(3), untagged(4)

portToVlanPvid		1.3.6.1.4.1.10297.202.7000.3.4.3.1.6
the VLAN ID to be the port-based VLAN ID for this port.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

portVlanTable		1.3.6.1.4.1.10297.202.7000.3.4.4
The table of port VLAN
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PortVlanEntry

portVlanEntry		1.3.6.1.4.1.10297.202.7000.3.4.4.1
The entry of port VLAN
Status: current	Access: not-accessible
OBJECT-TYPE
	PortVlanEntry

portVlanPortIndex		1.3.6.1.4.1.10297.202.7000.3.4.4.1.1
The port index of port VLAN
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

portVlanPortMode		1.3.6.1.4.1.10297.202.7000.3.4.4.1.2
the interface VLAN mode of this port
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	hybrid(1), access(2), trunk(3), tunnel(4)

portVlanAdminVlans		1.3.6.1.4.1.10297.202.7000.3.4.4.1.3
the administrative VLAN list of this port
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

portVlanOperVlans		1.3.6.1.4.1.10297.202.7000.3.4.4.1.4
The operational VLAN list of this port
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

voiceVlan		1.3.6.1.4.1.10297.202.7000.3.4.5
OBJECT IDENTIFIER

voiceVlanState		1.3.6.1.4.1.10297.202.7000.3.4.5.1
Voice VLAN state
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

voiceVlanId		1.3.6.1.4.1.10297.202.7000.3.4.5.2
Voice VLAN ID
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4094

voiceVlanRemarkCos-8021p		1.3.6.1.4.1.10297.202.7000.3.4.5.3
a value of vpt that will be advertised by LLDP-MED
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..7

voiceVlanRemark1q		1.3.6.1.4.1.10297.202.7000.3.4.5.4
1p remark state
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

voiceVlanAgingTime		1.3.6.1.4.1.10297.202.7000.3.4.5.5
value of aging time
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	30..65535

telephonyOUITable		1.3.6.1.4.1.10297.202.7000.3.4.5.6
The table of OUI
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TelephonyOUIEntry

telephonyOUIEntry		1.3.6.1.4.1.10297.202.7000.3.4.5.6.1
The entry of OUI
Status: current	Access: not-accessible
OBJECT-TYPE
	TelephonyOUIEntry

telephonyOUIIndex		1.3.6.1.4.1.10297.202.7000.3.4.5.6.1.1
The index of OUI
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..16

telephonyOUIAddress		1.3.6.1.4.1.10297.202.7000.3.4.5.6.1.2
oui address
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

telephonyOUIDescription		1.3.6.1.4.1.10297.202.7000.3.4.5.6.1.3
description of the specified MAC address to the voice VLAN OUI table
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

telephonyOUIRowStatus		1.3.6.1.4.1.10297.202.7000.3.4.5.6.1.99
User can use createAndWait(5) to create new entry. After setup the value, user use active(1) to set into switch. User can use destory to delete(6) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	active(1), notInService(2), createAndWait(5), destory(6)

telephonyOUIPortTable		1.3.6.1.4.1.10297.202.7000.3.4.5.7
The table of OUI port
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TelephonyOUIPortEntry

telephonyOUIPortEntry		1.3.6.1.4.1.10297.202.7000.3.4.5.7.1
The entry of OUI port
Status: current	Access: not-accessible
OBJECT-TYPE
	TelephonyOUIPortEntry

telephonyOUIPortIndex		1.3.6.1.4.1.10297.202.7000.3.4.5.7.1.1
The port index of OUI port
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

telephonyOUIState		1.3.6.1.4.1.10297.202.7000.3.4.5.7.1.2
Ingress/Egress type value
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

telephonyOUICosMode		1.3.6.1.4.1.10297.202.7000.3.4.5.7.1.3
port cos mode Src: QoS attributes are applied to packets with OUIs in the source MAC address. All: QoS attributes are applied to packets that are classified to the Voice VLAN
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	all(1), src(2)

interfaceVlanTable		1.3.6.1.4.1.10297.202.7000.3.4.6
The table of interface VLAN
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		InterfaceVlanEntry

interfaceVlanEntry		1.3.6.1.4.1.10297.202.7000.3.4.6.1
The entry of interface VLAN
Status: current	Access: not-accessible
OBJECT-TYPE
	InterfaceVlanEntry

interfaceVlanIndex		1.3.6.1.4.1.10297.202.7000.3.4.6.1.1
The index of interface VLAN
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4094

interfaceVlanId		1.3.6.1.4.1.10297.202.7000.3.4.6.1.2
The interface VLAN ID
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4094

interfaceVlanName		1.3.6.1.4.1.10297.202.7000.3.4.6.1.3
The name of interface VLAN
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

interfaceVlanRowStatus		1.3.6.1.4.1.10297.202.7000.3.4.6.1.99
User can use createAndWait(5) to create new entry. After setup the value, user use active(1) to set into switch. User can use destory to delete(6) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	active(1), notInService(2), createAndWait(5), destory(6)

eeePortTable		1.3.6.1.4.1.10297.202.7000.3.5.1
The table of EEE Port
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EeePortEntry

eeePortEntry		1.3.6.1.4.1.10297.202.7000.3.5.1.1
The entry of EEE Port
Status: current	Access: not-accessible
OBJECT-TYPE
	EeePortEntry

eeePortIndex		1.3.6.1.4.1.10297.202.7000.3.5.1.1.1
The port index of EEE Port
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

eeeState		1.3.6.1.4.1.10297.202.7000.3.5.1.1.2
Port EEE function.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

unknownMulticastAction		1.3.6.1.4.1.10297.202.7000.3.6.1
the unknown multicast action Drop: drop the unknown multicast data. Flood: flood the unknown multicast data. Router port: forward the unknown multicast data to router port.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	drop(1), flood(2), routerPort(3)

forwardMethod		1.3.6.1.4.1.10297.202.7000.3.6.2
the multicast forward method. MAC: forward method dmac+vid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	mac(1)

igmpSnooping		1.3.6.1.4.1.10297.202.7000.3.6.3
OBJECT IDENTIFIER

igmpSnoopingState		1.3.6.1.4.1.10297.202.7000.3.6.3.1
the enabling status of IGMP functionality
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disabled(2)

igmpSnoopingVersion		1.3.6.1.4.1.10297.202.7000.3.6.3.2
the igmp snooping version v2: Only support process igmp v2 packet. v3: Support v3 basic and v2.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	v2(1), v3(2)

igmpSnoopingReportSuppression		1.3.6.1.4.1.10297.202.7000.3.6.3.3
the enabling status of IGMP v2 report suppression
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disabled(2)

igmpSnoopingTable		1.3.6.1.4.1.10297.202.7000.3.6.3.4
The table of IGMP snooping
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IgmpSnoopingEntry

igmpSnoopingEntry		1.3.6.1.4.1.10297.202.7000.3.6.3.4.1
The entry of IGMP snooping
Status: current	Access: not-accessible
OBJECT-TYPE
	IgmpSnoopingEntry

igmpSnoopingIndex		1.3.6.1.4.1.10297.202.7000.3.6.3.4.1.1
The index of IGMP snooping
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

igmpSnoopingVlanId		1.3.6.1.4.1.10297.202.7000.3.6.3.4.1.2
The IGMP entry VLAN ID
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4904

igmpSnoopStatus		1.3.6.1.4.1.10297.202.7000.3.6.3.4.1.3
The enable status of IGMP VLAN functionality
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

routerPortsAutoLearn		1.3.6.1.4.1.10297.202.7000.3.6.3.4.1.4
The enable statue of IGMP router port learning.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

queryRobustness		1.3.6.1.4.1.10297.202.7000.3.6.3.4.1.5
The Robusstness Variable allows tuning for the expected packet loss on a subnet
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..7

queryInterval		1.3.6.1.4.1.10297.202.7000.3.6.3.4.1.6
The interval of querier send general query
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	30..18000

queryMaxResponseInterval		1.3.6.1.4.1.10297.202.7000.3.6.3.4.1.7
In Membership Query Message, it specifies the maximum allowed time before sending a responding report in units of 1/10 second
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	5..20

lastMemberQueryCounter		1.3.6.1.4.1.10297.202.7000.3.6.3.4.1.8
The count that Querier-switch sends Group-Specific Queriers when it receives a Leave Group message for a group
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..7

lastMemberQueryInterval		1.3.6.1.4.1.10297.202.7000.3.6.3.4.1.9
The interval that Querier-switch sends Group-Specific Queriers when it receives a Leave Group Message for a group
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..25

immediateLeave		1.3.6.1.4.1.10297.202.7000.3.6.3.4.1.10
Leave the group when receive IGMP Leave message.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

operQueryRobustness		1.3.6.1.4.1.10297.202.7000.3.6.3.4.1.11
The operation query robustness.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

operQueryInterval		1.3.6.1.4.1.10297.202.7000.3.6.3.4.1.12
The operation query interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

operQueryMaxResponseInterval		1.3.6.1.4.1.10297.202.7000.3.6.3.4.1.13
The operating query max response interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

operLastMemberQueryCounter		1.3.6.1.4.1.10297.202.7000.3.6.3.4.1.14
The operating last member query counter.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

operLastMemberQueryInterval		1.3.6.1.4.1.10297.202.7000.3.6.3.4.1.15
The operation last member query interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

igmpQuerierTable		1.3.6.1.4.1.10297.202.7000.3.6.3.5
The table of IGMP querier
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IgmpQuerierEntry

igmpQuerierEntry		1.3.6.1.4.1.10297.202.7000.3.6.3.5.1
The entry of IGMP querier
Status: current	Access: not-accessible
OBJECT-TYPE
	IgmpQuerierEntry

igmpQuerierVlanId		1.3.6.1.4.1.10297.202.7000.3.6.3.5.1.1
The VLAN ID of IGMP querier
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

igmpQuerierState		1.3.6.1.4.1.10297.202.7000.3.6.3.5.1.2
The enabling status of IGMP Querier Election on the chose VLANs
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

igmpQuerierStatus		1.3.6.1.4.1.10297.202.7000.3.6.3.5.1.3
The enabling status of IGMP Querier Election on the chose VLANs
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	querier(1), nonQuerier(2)

igmpQuerierVersion		1.3.6.1.4.1.10297.202.7000.3.6.3.5.1.4
The query version of IGMP Querier Election on the chose VLANs
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	v2(1), v3(2)

igmpQuerierIP		1.3.6.1.4.1.10297.202.7000.3.6.3.5.1.5
The query IP address of IGMP Querier Election on the chose VLANs
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

igmpStaticGroupTable		1.3.6.1.4.1.10297.202.7000.3.6.3.6
The table of IGMP static group
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IgmpStaticGroupEntry

igmpStaticGroupEntry		1.3.6.1.4.1.10297.202.7000.3.6.3.6.1
The entry of IGMP static group
Status: current	Access: not-accessible
OBJECT-TYPE
	IgmpStaticGroupEntry

igmpStaticGroupIndex		1.3.6.1.4.1.10297.202.7000.3.6.3.6.1.1
The index of IGMP static group
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..256

igmpStaticGroupVlanId		1.3.6.1.4.1.10297.202.7000.3.6.3.6.1.2
The VLAN ID of IGMP static group
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

igmpStaticGroupIPaddress		1.3.6.1.4.1.10297.202.7000.3.6.3.6.1.3
The IP address of this group
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

igmpStaticGroupMemberPorts		1.3.6.1.4.1.10297.202.7000.3.6.3.6.1.4
The member ports of this group
Status: current	Access: read-write
OBJECT-TYPE
	BITS	port1(0), port2(1), port3(2), port4(3), port5(4), port6(5), port7(6), port8(7), port9(8), port10(9), port11(10), port12(11), port13(12), port14(13), port15(14), port16(15), port17(16), port18(17), port19(18), port20(19), port21(20), port22(21), port23(22), port24(23), port25(24), port26(25), port27(26), port28(27), port29(28), port30(29), port31(30), port32(31)

igmpStaticGroupRowStatus		1.3.6.1.4.1.10297.202.7000.3.6.3.6.1.99
User can use createAndWait(5) to create new entry. After setup the value, user use active(1) to set into switch. User can use destory to delete(6) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	active(1), notInService(2), createAndWait(5), destory(6)

igmpGroupTable		1.3.6.1.4.1.10297.202.7000.3.6.3.7
The table of IGMP group
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IgmpGroupEntry

igmpGroupEntry		1.3.6.1.4.1.10297.202.7000.3.6.3.7.1
The entry of IGMP group
Status: current	Access: not-accessible
OBJECT-TYPE
	IgmpGroupEntry

igmpGroupVlanId		1.3.6.1.4.1.10297.202.7000.3.6.3.7.1.1
The VLAN ID of IGMP group
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

igmpGroupIPaddress		1.3.6.1.4.1.10297.202.7000.3.6.3.7.1.2
The group IP address of this group
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

igmpGroupMemberPorts		1.3.6.1.4.1.10297.202.7000.3.6.3.7.1.3
The member ports of this group
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

igmpGroupType		1.3.6.1.4.1.10297.202.7000.3.6.3.7.1.4
The type of this group
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	static(1), dynamic(2)

igmpGroupLife		1.3.6.1.4.1.10297.202.7000.3.6.3.7.1.5
The life time of this group
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

igmpRouterTable		1.3.6.1.4.1.10297.202.7000.3.6.3.8
The table of IGMP router
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IgmpRouterEntry

igmpRouterEntry		1.3.6.1.4.1.10297.202.7000.3.6.3.8.1
The entry of IGMP router
Status: current	Access: not-accessible
OBJECT-TYPE
	IgmpRouterEntry

igmpRouterVlanId		1.3.6.1.4.1.10297.202.7000.3.6.3.8.1.1
The VLAN ID of the IGMP router.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

igmpRouterPort		1.3.6.1.4.1.10297.202.7000.3.6.3.8.1.2
The port of the IGMP router.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

igmpRouterExpireTime		1.3.6.1.4.1.10297.202.7000.3.6.3.8.1.3
The expire time of the IGMP router.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mldSnooping		1.3.6.1.4.1.10297.202.7000.3.6.4
OBJECT IDENTIFIER

mldSnoopingState		1.3.6.1.4.1.10297.202.7000.3.6.4.1
the enabling status of MLD functionality
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disabled(2)

mldSnoopingVersion		1.3.6.1.4.1.10297.202.7000.3.6.4.2
the MLD snooping version
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	v1(1), v2(2)

mldSnoopingReportSuppression		1.3.6.1.4.1.10297.202.7000.3.6.4.3
the enabling status of MLD report suppression
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disabled(2)

mldSnoopingTable		1.3.6.1.4.1.10297.202.7000.3.6.4.4
The table of MLD snooping
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MLDSnoopingEntry

mldSnoopingEntry		1.3.6.1.4.1.10297.202.7000.3.6.4.4.1
The entry of MLD snooping
Status: current	Access: not-accessible
OBJECT-TYPE
	MLDSnoopingEntry

mldSnoopingIndex		1.3.6.1.4.1.10297.202.7000.3.6.4.4.1.1
The index of MLD snooping
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

mldSnoopingVlanId		1.3.6.1.4.1.10297.202.7000.3.6.4.4.1.2
The MLD entry VLAN ID
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4904

mldSnoopStatus		1.3.6.1.4.1.10297.202.7000.3.6.4.4.1.3
The enable status of MLD VLAN functionality
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mldSnoopRouterPortsAutoLearn		1.3.6.1.4.1.10297.202.7000.3.6.4.4.1.4
The enable statue of MLD router port learning.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mldSnoopQueryRobustness		1.3.6.1.4.1.10297.202.7000.3.6.4.4.1.5
The Robusstness Variable allows tuning for the expected packet loss on a subnet
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..7

mldSnoopQueryInterval		1.3.6.1.4.1.10297.202.7000.3.6.4.4.1.6
The interval of querier send general query
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	30..18000

mldSnoopQueryMaxResponseInterval		1.3.6.1.4.1.10297.202.7000.3.6.4.4.1.7
In Membership Query Message, it specifies the maximum allowed time before sending a responding report in units of 1/10 second
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	5..20

mldSnoopLastMemberQueryCounter		1.3.6.1.4.1.10297.202.7000.3.6.4.4.1.8
The count that Querier-switch sends Group-Specific Queriers when it receives a Leave Group message for a group
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..7

mldSnoopLastMemberQueryInterval		1.3.6.1.4.1.10297.202.7000.3.6.4.4.1.9
The interval that Querier-switch sends Group-Specific Queriers when it receives a Leave Group Message for a group
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..25

mldSnoopImmediateLeave		1.3.6.1.4.1.10297.202.7000.3.6.4.4.1.10
Leave the group when receive MLD Leave message.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

operMldSnoopQueryRobustness		1.3.6.1.4.1.10297.202.7000.3.6.4.4.1.11
The operation MLD query robustness.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

operMldSnoopQueryInterval		1.3.6.1.4.1.10297.202.7000.3.6.4.4.1.12
The operation MLD query interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

operMldSnoopQueryMaxResponseInterval		1.3.6.1.4.1.10297.202.7000.3.6.4.4.1.13
The operating MLD query max response interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

operMldSnoopLastMemberQueryCounter		1.3.6.1.4.1.10297.202.7000.3.6.4.4.1.14
The operating MLD last member query counter.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

operMldSnoopLastMemberQueryInterval		1.3.6.1.4.1.10297.202.7000.3.6.4.4.1.15
The operation MLD last member query interval.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mldQuerierTable		1.3.6.1.4.1.10297.202.7000.3.6.4.5
The table of MLD querier
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MLDQuerierEntry

mldQuerierEntry		1.3.6.1.4.1.10297.202.7000.3.6.4.5.1
The entry of MLD querier
Status: current	Access: not-accessible
OBJECT-TYPE
	MLDQuerierEntry

mldQuerierVlanId		1.3.6.1.4.1.10297.202.7000.3.6.4.5.1.1
The VLAN ID of MLD querier
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

mldQuerierState		1.3.6.1.4.1.10297.202.7000.3.6.4.5.1.2
The enabling status of MLD Querier Election on the chose VLANs
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

mldQuerierStatus		1.3.6.1.4.1.10297.202.7000.3.6.4.5.1.3
The querier status of MLD Querier Election on the chose VLANs
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	querier(1), nonQuerier(2)

mldQuerierVersion		1.3.6.1.4.1.10297.202.7000.3.6.4.5.1.4
The query version of MLD Querier Election on the chose VLANs
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	v1(1), v2(2)

mldQuerierIP		1.3.6.1.4.1.10297.202.7000.3.6.4.5.1.5
The query IP address of MLD Querier Election on the chose VLANs
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

mldStaticGroupTable		1.3.6.1.4.1.10297.202.7000.3.6.4.6
The table of MLD static group
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MLDStaticGroupEntry

mldStaticGroupEntry		1.3.6.1.4.1.10297.202.7000.3.6.4.6.1
The entry of MLD static group
Status: current	Access: not-accessible
OBJECT-TYPE
	MLDStaticGroupEntry

mldStaticGroupIndex		1.3.6.1.4.1.10297.202.7000.3.6.4.6.1.1
The index of MLD static group
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..256

mldStaticGroupVlanId		1.3.6.1.4.1.10297.202.7000.3.6.4.6.1.2
The VLAN ID of MLD static group
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4094

mldStaticGroupIPaddress		1.3.6.1.4.1.10297.202.7000.3.6.4.6.1.3
The IP address of this group
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

mldStaticGroupMemberPorts		1.3.6.1.4.1.10297.202.7000.3.6.4.6.1.4
The member ports of this group
Status: current	Access: read-write
OBJECT-TYPE
	BITS	port1(0), port2(1), port3(2), port4(3), port5(4), port6(5), port7(6), port8(7), port9(8), port10(9), port11(10), port12(11), port13(12), port14(13), port15(14), port16(15), port17(16), port18(17), port19(18), port20(19), port21(20), port22(21), port23(22), port24(23), port25(24), port26(25), port27(26), port28(27), port29(28), port30(29), port31(30), port32(31)

mldStaticGroupRowStatus		1.3.6.1.4.1.10297.202.7000.3.6.4.6.1.99
User can use createAndWait(5) to create new entry. After setup the value, user use active(1) to set into switch. User can use destory to delete(6) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	active(1), notInService(2), createAndWait(5), destory(6)

mldGroupTable		1.3.6.1.4.1.10297.202.7000.3.6.4.7
The table of MLD group
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MLDGroupEntry

mldGroupEntry		1.3.6.1.4.1.10297.202.7000.3.6.4.7.1
The entry of MLD group
Status: current	Access: not-accessible
OBJECT-TYPE
	MLDGroupEntry

mldGroupVlanId		1.3.6.1.4.1.10297.202.7000.3.6.4.7.1.1
The VLAN ID of MLD group
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

mldGroupIPaddress		1.3.6.1.4.1.10297.202.7000.3.6.4.7.1.2
The group IP address of this group
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

mldGroupMemberPorts		1.3.6.1.4.1.10297.202.7000.3.6.4.7.1.3
The member ports of this group
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

mldGroupType		1.3.6.1.4.1.10297.202.7000.3.6.4.7.1.4
The type of this group
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	static(1), dynamic(2)

mldGroupLife		1.3.6.1.4.1.10297.202.7000.3.6.4.7.1.5
The life time of this group
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mldRouterTable		1.3.6.1.4.1.10297.202.7000.3.6.4.8
The table of MLD router
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MLDRouterEntry

mldRouterEntry		1.3.6.1.4.1.10297.202.7000.3.6.4.8.1
The entry of MLD router
Status: current	Access: not-accessible
OBJECT-TYPE
	MLDRouterEntry

mldRouterVlanId		1.3.6.1.4.1.10297.202.7000.3.6.4.8.1.1
The VLAN ID of the MLD router.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

mldRouterPort		1.3.6.1.4.1.10297.202.7000.3.6.4.8.1.2
The port of the MLD router.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

mldRouterExpireTime		1.3.6.1.4.1.10297.202.7000.3.6.4.8.1.3
The expire time of the MLD router.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

jamboFramePktSize		1.3.6.1.4.1.10297.202.7000.3.7.1
Jumbo frame size
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1518..9216

stpEnable		1.3.6.1.4.1.10297.202.7000.3.8.1
Specify the STP status to be enable/disable on the switch. Enable STP will block all switch port and SNMP set will timeout.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

bpduForward		1.3.6.1.4.1.10297.202.7000.3.8.2
The BPDU forwarding action when the global STP is disable
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	flooding(1), filtering(2)

pathCostMethod		1.3.6.1.4.1.10297.202.7000.3.8.3
The path cost method of STP
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	short(1), long(2)

forceVersion		1.3.6.1.4.1.10297.202.7000.3.8.4
The operating mode of STP STP-compatible: IEEE 802.1D STP operation RSTP-Operation: IEEE 802.1W operation
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	stp-compatible(1), rstp-operation(2), mstp-operation(3)

stpPortTable		1.3.6.1.4.1.10297.202.7000.3.8.5
The table of STP port
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		StpPortEntry

stpPortEntry		1.3.6.1.4.1.10297.202.7000.3.8.5.1
The entry of STP port
Status: current	Access: not-accessible
OBJECT-TYPE
	StpPortEntry

stpPortIndex		1.3.6.1.4.1.10297.202.7000.3.8.5.1.1
The port index of STP
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

stpAdminEnable		1.3.6.1.4.1.10297.202.7000.3.8.5.1.2
enable/disable the STP port state
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

stpPathCost		1.3.6.1.4.1.10297.202.7000.3.8.5.1.3
the port is contribution, when it is the Root Port, to the Root Path Cost for the Bridge. (0 means 'Auto')
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

stpEdgePort		1.3.6.1.4.1.10297.202.7000.3.8.5.1.4
the edge port configuration: No: Force to false state (as link to a bridge). Yes: Force to true state (as link to a host).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	yes(1), no(2)

stpP2pMac		1.3.6.1.4.1.10297.202.7000.3.8.5.1.5
the Point-to-Point port configuration:
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	yes(1), no(2)

stpMigrate		1.3.6.1.4.1.10297.202.7000.3.8.5.1.6
Force to try to use the new MST/RST BPDUs, and hence to test the hypothesis that all legacy systems that do not understand the new BPDU formats have been removed from the LAN segment on the port(s).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

stpBridgeInfo		1.3.6.1.4.1.10297.202.7000.3.8.6
OBJECT IDENTIFIER

stpBridgePriority		1.3.6.1.4.1.10297.202.7000.3.8.6.1
the Bridge Priority in the CIST instance. Priority support the following value: 0, 4096, 8192, 12288, 16384, 20480, 24576, 28672, 32768, 36864, 40960, 45056, 49152, 53248, 57344, 61440
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

stpBridgeForwardDelay		1.3.6.1.4.1.10297.202.7000.3.8.6.2
the delay time an interface takes to converge from blocking state to forwarding state. Max Age <= 2*(Forward Delay Time - 1)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	4..30

stpBridgeMaxAge		1.3.6.1.4.1.10297.202.7000.3.8.6.3
the time any switch should wait before trying to change the STP topology after unhearing Hello BPUD. Max Age <= 2(Forward Delay Time - 1) Max Age >= 2(Hello Time + 1)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	6..40

stpBridgeTxHoldCount		1.3.6.1.4.1.10297.202.7000.3.8.6.4
the Transmit Hold Count used to limit BPDU transmission rate.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..10

stpBridgeHelloTime		1.3.6.1.4.1.10297.202.7000.3.8.6.5
the interval between periodic transmissions of BPDU by Designated Ports. Max Age >= 2*(Hello Time + 1)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..10

stpBridgeStatus		1.3.6.1.4.1.10297.202.7000.3.8.7
OBJECT IDENTIFIER

bridgeIdentifier		1.3.6.1.4.1.10297.202.7000.3.8.7.1
STP bridge identifier
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

definatedRootBridge		1.3.6.1.4.1.10297.202.7000.3.8.7.2
STP destination root bridge ID
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rootPathCost		1.3.6.1.4.1.10297.202.7000.3.8.7.3
STP root path cost
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

designatedBridge		1.3.6.1.4.1.10297.202.7000.3.8.7.4
STP designated bridge
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

rootPort		1.3.6.1.4.1.10297.202.7000.3.8.7.5
STP root port
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lastTopologyChange		1.3.6.1.4.1.10297.202.7000.3.8.7.6
STP last topology change
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

stpPortStatusTable		1.3.6.1.4.1.10297.202.7000.3.8.8
The table of STP port status
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		StpPortStatusEntry

stpPortStatusEntry		1.3.6.1.4.1.10297.202.7000.3.8.8.1
The entry of STP port status
Status: current	Access: not-accessible
OBJECT-TYPE
	StpPortStatusEntry

stpPortStatusIndex		1.3.6.1.4.1.10297.202.7000.3.8.8.1.1
The index of STP port status
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

stpPortPriority		1.3.6.1.4.1.10297.202.7000.3.8.8.1.2
The Port Priority to the selected ports in the CIST instance. Priority support the following value: 0, 16, 32, 48, 64, 80, 96, 112, 128, 144, 160, 176, 192, 208, 224, 240
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

stpPortPathCost		1.3.6.1.4.1.10297.202.7000.3.8.8.1.3
Path Cost to the selected ports in the CIST instance. (0 means `Auto`)
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

stpPortDesignatedRootBridge		1.3.6.1.4.1.10297.202.7000.3.8.8.1.4
The designated root bridge
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

stpPortRootPathCost		1.3.6.1.4.1.10297.202.7000.3.8.8.1.5
The root path cost
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

stpPortDesignatedBridge		1.3.6.1.4.1.10297.202.7000.3.8.8.1.6
The designated bridge
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

stpPortEdgrPortConf		1.3.6.1.4.1.10297.202.7000.3.8.8.1.7
The edge port configuration
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

stpPortP2PMacConf		1.3.6.1.4.1.10297.202.7000.3.8.8.1.8
The point-to-point MAC configuration
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

stpPortRoles		1.3.6.1.4.1.10297.202.7000.3.8.8.1.9
The port roles
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(0), master(1), root(2), designated(3), alternate(4), backup(5)

stpPortStatus		1.3.6.1.4.1.10297.202.7000.3.8.8.1.10
The port status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disabled(0), discarding(1), learning(2), forwarding(3)

stpStatisticTable		1.3.6.1.4.1.10297.202.7000.3.8.9
The table of STP statistic
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		StpStatisticEntry

stpStatisticEntry		1.3.6.1.4.1.10297.202.7000.3.8.9.1
The entry of STP statistic
Status: current	Access: not-accessible
OBJECT-TYPE
	StpStatisticEntry

stpStatisticPortIndex		1.3.6.1.4.1.10297.202.7000.3.8.9.1.1
The port index of STP statistic
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

configurationBPDUsReceived		1.3.6.1.4.1.10297.202.7000.3.8.9.1.2
The configuration BPDU received
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

tcnBPDUsReceived		1.3.6.1.4.1.10297.202.7000.3.8.9.1.3
The TCN BPDU received
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

configurationBPDUsTransmitted		1.3.6.1.4.1.10297.202.7000.3.8.9.1.4
The configuration BPDU transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

tcnBPDUsTransmitted		1.3.6.1.4.1.10297.202.7000.3.8.9.1.5
The TCN BPDU transmitted
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mstp		1.3.6.1.4.1.10297.202.7000.3.8.10
OBJECT IDENTIFIER

mstConfigIdentification		1.3.6.1.4.1.10297.202.7000.3.8.10.1
OBJECT IDENTIFIER

mstConfigName		1.3.6.1.4.1.10297.202.7000.3.8.10.1.1
The configuration name of MSTP
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

mstRevisionLevel		1.3.6.1.4.1.10297.202.7000.3.8.10.1.2
The revision level of MSTP
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

mstInstanceID		1.3.6.1.4.1.10297.202.7000.3.8.10.2
OBJECT IDENTIFIER

mstiIDSetting		1.3.6.1.4.1.10297.202.7000.3.8.10.2.1
The MSTI ID of MST instance ID
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..15

mstiVlanListSetting		1.3.6.1.4.1.10297.202.7000.3.8.10.2.2
The VLAN list of MST instance ID
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

mstiIDSettingMove		1.3.6.1.4.1.10297.202.7000.3.8.10.2.3
The moving action of MST instance ID
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nothing(1), move(2)

mstiIDInfoTable		1.3.6.1.4.1.10297.202.7000.3.8.10.2.4
The table of MST instance ID info
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MSTIIDEntry

mstiIDInfoEntry		1.3.6.1.4.1.10297.202.7000.3.8.10.2.4.1
The entry of MST instance ID info
Status: current	Access: not-accessible
OBJECT-TYPE
	MSTIIDEntry

mstiIDIndex		1.3.6.1.4.1.10297.202.7000.3.8.10.2.4.1.1
The MSTI ID of MST instance ID info
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..15

mstiVLANList		1.3.6.1.4.1.10297.202.7000.3.8.10.2.4.1.2
The VLAN List of MST instance ID info
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

stpInstance		1.3.6.1.4.1.10297.202.7000.3.8.10.3
OBJECT IDENTIFIER

stpPriorityInfoTable		1.3.6.1.4.1.10297.202.7000.3.8.10.3.1
The table of STP priority info
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		STPPriorityInfoEntry

stpPriorityInfoEntry		1.3.6.1.4.1.10297.202.7000.3.8.10.3.1.1
The entry of STP priority info
Status: current	Access: not-accessible
OBJECT-TYPE
	STPPriorityInfoEntry

stpMstiIDIndex		1.3.6.1.4.1.10297.202.7000.3.8.10.3.1.1.1
The MSTI ID of STP instance info
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..15

stpPriorityValue		1.3.6.1.4.1.10297.202.7000.3.8.10.3.1.1.2
The priority of STP instance info. Priority support the following value: 0, 4096, 8192, 12288, 16384, 20480, 24576, 28672, 32768, 36864, 40960, 45056, 49152, 53248, 57344, 61440
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

stpPriorityDefault		1.3.6.1.4.1.10297.202.7000.3.8.10.3.1.1.3
Set the priority to default value.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nothing(1), default(2)

mstInstanceInfo		1.3.6.1.4.1.10297.202.7000.3.8.10.4
OBJECT IDENTIFIER

mstBridgeIdentifier		1.3.6.1.4.1.10297.202.7000.3.8.10.4.1
STP bridge identifier in MST
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

mstDesignatedRootBridge		1.3.6.1.4.1.10297.202.7000.3.8.10.4.2
STP destination root bridge ID in MST
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

mstRootPathCost		1.3.6.1.4.1.10297.202.7000.3.8.10.4.3
STP root path cost in MST
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

mstDesignatedBridge		1.3.6.1.4.1.10297.202.7000.3.8.10.4.4
STP designated bridge in MST
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

mstRootPort		1.3.6.1.4.1.10297.202.7000.3.8.10.4.5
STP root port in MST
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

mstLastTopologyChange		1.3.6.1.4.1.10297.202.7000.3.8.10.4.6
STP last topology change in MST
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

mstStpPortStatusTable		1.3.6.1.4.1.10297.202.7000.3.8.10.4.7
The table of STP port status in MST
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MSTStpPortStatusEntry

mstStpPortStatusEntry		1.3.6.1.4.1.10297.202.7000.3.8.10.4.7.1
The entry of STP port status in MST
Status: current	Access: not-accessible
OBJECT-TYPE
	MSTStpPortStatusEntry

mstStpPortStatusIndex		1.3.6.1.4.1.10297.202.7000.3.8.10.4.7.1.1
The index of STP port status in MST
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

mstStpPortPriority		1.3.6.1.4.1.10297.202.7000.3.8.10.4.7.1.2
The Port Priority to the selected ports in the CIST instance. Priority support the following value: 0, 16, 32, 48, 64, 80, 96, 112, 128, 144, 160, 176, 192, 208, 224, 240
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

mstStpPortPathCost		1.3.6.1.4.1.10297.202.7000.3.8.10.4.7.1.3
Path Cost to the selected ports in the CIST instance. (0 means `Auto`)
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

mstStpPortDesignatedRootBridge		1.3.6.1.4.1.10297.202.7000.3.8.10.4.7.1.4
The designated root bridge
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

mstStpPortRootPathCost		1.3.6.1.4.1.10297.202.7000.3.8.10.4.7.1.5
The root path cost
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

mstStpPortDesignatedBridge		1.3.6.1.4.1.10297.202.7000.3.8.10.4.7.1.6
The designated bridge
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

mstStpPortEdgrPortConf		1.3.6.1.4.1.10297.202.7000.3.8.10.4.7.1.7
The edge port configuration
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

mstStpPortP2PMacConf		1.3.6.1.4.1.10297.202.7000.3.8.10.4.7.1.8
The point-to-point MAC configuration
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

mstStpPortRoles		1.3.6.1.4.1.10297.202.7000.3.8.10.4.7.1.9
The port roles
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

mstStpPortStatus		1.3.6.1.4.1.10297.202.7000.3.8.10.4.7.1.10
The port status
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

mstInstanceInfoID		1.3.6.1.4.1.10297.202.7000.3.8.10.4.8
MST instance ID
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

outerVlanEthtype		1.3.6.1.4.1.10297.202.7000.3.9.1
Q-in-Q outer VLAN ether type
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

qinqPortInfoTable		1.3.6.1.4.1.10297.202.7000.3.9.2
The table of Q-in-Q port info
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QinQPortInfoEntry

qinqPortInfoEntry		1.3.6.1.4.1.10297.202.7000.3.9.2.1
The entry of Q-in-Q port info
Status: current	Access: not-accessible
OBJECT-TYPE
	QinQPortInfoEntry

qinqPortIndex		1.3.6.1.4.1.10297.202.7000.3.9.2.1.1
The port index of Q-in-Q port info
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

qinqOuterPVID		1.3.6.1.4.1.10297.202.7000.3.9.2.1.2
The Q-in-Q outer PVID
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..4094

qinqOuterMode		1.3.6.1.4.1.10297.202.7000.3.9.2.1.3
The Q-in-Q outer mode
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nni(1), uni(2)

garpJoinTime		1.3.6.1.4.1.10297.202.7000.3.10.1
The GARP join time. Join time * 2 must be below leave time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..600

garpLeaveTime		1.3.6.1.4.1.10297.202.7000.3.10.2
The GARP leave time. The leave time must below leave all time and bigger then Join time * 2
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..3000

garpLeaveAllTime		1.3.6.1.4.1.10297.202.7000.3.10.3
The GARP leave all time. The leave all time must bigger then leave time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	2..12000

gvrpStatus		1.3.6.1.4.1.10297.202.7000.3.11.1
The status of GVRP.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

xRingEliteState		1.3.6.1.4.1.10297.202.7000.3.12.1
The status of X-Ring Elite.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

xRingEliteRingIDTable		1.3.6.1.4.1.10297.202.7000.3.12.2
The table of X-Ring Elite ring ID
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		XRingEliteRingIDEntry

xRingEliteRingIDEntry		1.3.6.1.4.1.10297.202.7000.3.12.2.1
The entry of X-Ring Elite ring ID
Status: current	Access: not-accessible
OBJECT-TYPE
	XRingEliteRingIDEntry

xRingEliteRingIDIndex		1.3.6.1.4.1.10297.202.7000.3.12.2.1.1
The index of X-Ring Elite ring ID
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..512

xRingEliteRingID		1.3.6.1.4.1.10297.202.7000.3.12.2.1.2
The ring ID of X-Ring Elite
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

xRingEliteRule		1.3.6.1.4.1.10297.202.7000.3.12.2.1.3
The rule of the X-Ring Elite
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	basic(1), couple(2), tunnel(3), mrm(4), mrc(5), legacy(6)

xRingElitePort1		1.3.6.1.4.1.10297.202.7000.3.12.2.1.4
The port1 of this X-Ring Elite. For trunk port : Trunk1 is 1000, Trunk2 is 1001, ...
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

xRingElitePort2		1.3.6.1.4.1.10297.202.7000.3.12.2.1.5
The port2 of this X-Ring Elite. For trunk port : Trunk1 is 1000, Trunk2 is 1001, ...
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

xRingEliteRingIDStatus		1.3.6.1.4.1.10297.202.7000.3.12.2.1.6
The status of this X-Ring Elite
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

xRingElitePort1Status		1.3.6.1.4.1.10297.202.7000.3.12.2.1.7
The port1 status of this X-Ring Elite
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

xRingElitePort2Status		1.3.6.1.4.1.10297.202.7000.3.12.2.1.8
The port2 status of this X-Ring Elite
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

xRingEliteRowStatus		1.3.6.1.4.1.10297.202.7000.3.12.2.1.99
User can use createAndWait(5) to create new entry. After setup the value, user use active(1) to set into switch. User can use destory to delete(6) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	active(1), notInService(2), createAndWait(5), destory(6)

loopbackEnabled		1.3.6.1.4.1.10297.202.7000.3.13.1
The status of loopback detection.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

loopbackInterval		1.3.6.1.4.1.10297.202.7000.3.13.2
The interval of loopback detection.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..32767

loopbackRecoverTime		1.3.6.1.4.1.10297.202.7000.3.13.3
The recover time of loopback detection.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	60..1000000

loopbackPortTable		1.3.6.1.4.1.10297.202.7000.3.13.4
The port table of loopback detection
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LoopbackPortEntry

loopbackPortEntry		1.3.6.1.4.1.10297.202.7000.3.13.4.1
The port entry of loopback detection
Status: current	Access: not-accessible
OBJECT-TYPE
	LoopbackPortEntry

loopbackPortIndex		1.3.6.1.4.1.10297.202.7000.3.13.4.1.1
The index of port loopback detection
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

loopbackPortEnabled		1.3.6.1.4.1.10297.202.7000.3.13.4.1.2
The enabled status of port loopback detection
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

loopbackPortLoopStatus		1.3.6.1.4.1.10297.202.7000.3.13.4.1.3
The loop status of port loopback detection
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	normal(1), shutdown(2)

xRingProStatus		1.3.6.1.4.1.10297.202.7000.3.14.1
The status of X-Ring Pro
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

xRingProRingSetting		1.3.6.1.4.1.10297.202.7000.3.14.2
OBJECT IDENTIFIER

xRingProRingID		1.3.6.1.4.1.10297.202.7000.3.14.2.1
The ring ID of X-Ring Pro
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

xRingProRingPort1		1.3.6.1.4.1.10297.202.7000.3.14.2.2
The port1 of X-Ring Pro. For trunk port : Trunk1 is 1000, Trunk2 is 1001, ...
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

xRingProRingPort2		1.3.6.1.4.1.10297.202.7000.3.14.2.3
The port2 of X-Ring Pro. For trunk port : Trunk1 is 1000, Trunk2 is 1001, ...
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

xRingProRingAdd		1.3.6.1.4.1.10297.202.7000.3.14.2.4
The add action of X-Ring Pro
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nothing(0), add(1)

xRingProCoupleSetting		1.3.6.1.4.1.10297.202.7000.3.14.3
OBJECT IDENTIFIER

xRingProCoupleID		1.3.6.1.4.1.10297.202.7000.3.14.3.1
The couple ring ID of X-Ring Pro
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

xRingProCouplePort		1.3.6.1.4.1.10297.202.7000.3.14.3.2
The couple port of X-Ring Pro
Status: current	Access: read-write
OBJECT-TYPE
	BITS	port1(0), port2(1), port3(2), port4(3), port5(4), port6(5), port7(6), port8(7), port9(8), port10(9), port11(10), port12(11), port13(12), port14(13), port15(14), port16(15), port17(16), port18(17), port19(18), port20(19), port21(20), port22(21), port23(22), port24(23), port25(24), port26(25), port27(26), port28(27), port29(28), port30(29), port31(30), port32(31)

xRingProCoupleMasterRingID		1.3.6.1.4.1.10297.202.7000.3.14.3.3
The master ring ID of X-Ring Pro
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

xRingProCoupleAdd		1.3.6.1.4.1.10297.202.7000.3.14.3.4
The add action of X-Ring Pro
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nothing(0), add(1)

xRingProInfoTable		1.3.6.1.4.1.10297.202.7000.3.14.4
The table of X-Ring Pro Infomation
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		XRingProInfoEntry

xRingProInfoEntry		1.3.6.1.4.1.10297.202.7000.3.14.4.1
The entry of X-Ring Pro Infomation
Status: current	Access: not-accessible
OBJECT-TYPE
	XRingProInfoEntry

xRingProInfoRingID		1.3.6.1.4.1.10297.202.7000.3.14.4.1.1
The ring ID of X-Ring Pro Infomation
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

xRingProInfoMode		1.3.6.1.4.1.10297.202.7000.3.14.4.1.2
The mode of X-Ring Pro Infomation
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

xRingProInfoOperState		1.3.6.1.4.1.10297.202.7000.3.14.4.1.3
The operation state of X-Ring Pro Infomation
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

xRingProInfoPort1		1.3.6.1.4.1.10297.202.7000.3.14.4.1.4
The port1 of X-Ring Pro Infomation.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

xRingProInfoPort1FwdState		1.3.6.1.4.1.10297.202.7000.3.14.4.1.5
The port1 forwarding state of X-Ring Pro Infomation
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

xRingProInfoPort2		1.3.6.1.4.1.10297.202.7000.3.14.4.1.6
The port2 of X-Ring Pro Infomation
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

xRingProInfoPort2FwdState		1.3.6.1.4.1.10297.202.7000.3.14.4.1.7
The port2 forwarding state of X-Ring Pro Infomation
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

xRingProInfoDel		1.3.6.1.4.1.10297.202.7000.3.14.4.1.8
The delete action of X-Ring Pro Infomation
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nothing(0), del(1)

xRingProInfoRole		1.3.6.1.4.1.10297.202.7000.3.14.4.1.9
The role of X-Ring Pro Infomation
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	member(0), head(1), tail(2), none(3)

xRingProPairSetting		1.3.6.1.4.1.10297.202.7000.3.14.5
OBJECT IDENTIFIER

xRingProPairID		1.3.6.1.4.1.10297.202.7000.3.14.5.1
The pair ring ID of X-Ring Pro
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

xRingProPairPort		1.3.6.1.4.1.10297.202.7000.3.14.5.2
The pair port of X-Ring Pro
Status: current	Access: read-write
OBJECT-TYPE
	BITS	port1(0), port2(1), port3(2), port4(3), port5(4), port6(5), port7(6), port8(7), port9(8), port10(9), port11(10), port12(11), port13(12), port14(13), port15(14), port16(15), port17(16), port18(17), port19(18), port20(19), port21(20), port22(21), port23(22), port24(23), port25(24), port26(25), port27(26), port28(27), port29(28), port30(29), port31(30), port32(31)

xRingProPairMasterRingID		1.3.6.1.4.1.10297.202.7000.3.14.5.3
The pair master ring ID of X-Ring Pro
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

xRingProPairAdd		1.3.6.1.4.1.10297.202.7000.3.14.5.4
The add action of X-Ring Pro
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nothing(0), add(1)

xRingProRPairSetting		1.3.6.1.4.1.10297.202.7000.3.14.6
OBJECT IDENTIFIER

xRingProRPairID		1.3.6.1.4.1.10297.202.7000.3.14.6.1
The R-pair ring ID of X-Ring Pro
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

xRingProRPairPort		1.3.6.1.4.1.10297.202.7000.3.14.6.2
The R-pair port of X-Ring Pro
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

xRingProRPairMasterRingID		1.3.6.1.4.1.10297.202.7000.3.14.6.3
The R-pair master ring ID of X-Ring Pro
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

xRingProRPairAdd		1.3.6.1.4.1.10297.202.7000.3.14.6.4
The add action of X-Ring Pro
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nothing(0), add(1)

xRingProChainSetting		1.3.6.1.4.1.10297.202.7000.3.14.7
OBJECT IDENTIFIER

xRingProChainID		1.3.6.1.4.1.10297.202.7000.3.14.7.1
The chain ring ID of X-Ring Pro
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

xRingProChainRole		1.3.6.1.4.1.10297.202.7000.3.14.7.2
The role of X-Ring Pro.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	member(0), head(1), tail(2)

xRingProChainHeadPort		1.3.6.1.4.1.10297.202.7000.3.14.7.3
The head port of X-Ring Pro. For trunk port : Trunk1 is 1000, Trunk2 is 1001, ...
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

xRingProChainMemberPort		1.3.6.1.4.1.10297.202.7000.3.14.7.4
The member port of X-Ring Pro. For trunk port : Trunk1 is 1000, Trunk2 is 1001, ...
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

xRingProChainAdd		1.3.6.1.4.1.10297.202.7000.3.14.7.5
The add action of X-Ring Pro
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nothing(0), add(1)

gmrpStatus		1.3.6.1.4.1.10297.202.7000.3.15.1
The status of GMRP.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

gmrpMulticastGroupTable		1.3.6.1.4.1.10297.202.7000.3.15.2
The table of GMRP multicast group
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		GMRPMulticastGroupEntry

gmrpMulticastGroupEntry		1.3.6.1.4.1.10297.202.7000.3.15.2.1
The entry of GMRP multicast group
Status: current	Access: not-accessible
OBJECT-TYPE
	GMRPMulticastGroupEntry

gmrpMulticastGroupIndex		1.3.6.1.4.1.10297.202.7000.3.15.2.1.1
The index of GMRP multicast group
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..10

gmrpMulticastGroupVlanId		1.3.6.1.4.1.10297.202.7000.3.15.2.1.2
The vlan id of GMRP multicast group
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

gmrpMulticastGroupMacAddress		1.3.6.1.4.1.10297.202.7000.3.15.2.1.3
The MAC address of GMRP multicast group
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

gmrpMulticastGroupType		1.3.6.1.4.1.10297.202.7000.3.15.2.1.4
The type of GMRP multicast group
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	static(1), dynamic(2)

gmrpMulticastGroupMemberPorts		1.3.6.1.4.1.10297.202.7000.3.15.2.1.5
The member ports of GMRP multicast group
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

erpsState		1.3.6.1.4.1.10297.202.7000.3.16.1
The status of ERPS
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

erpsGroupTable		1.3.6.1.4.1.10297.202.7000.3.16.2
The table of ERPS group.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ErpsGroupEntry

erpsGroupEntry		1.3.6.1.4.1.10297.202.7000.3.16.2.1
The entry of ERPS group.
Status: current	Access: not-accessible
OBJECT-TYPE
	ErpsGroupEntry

erpsGroupRingIndex		1.3.6.1.4.1.10297.202.7000.3.16.2.1.1
The index of ERPS group.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..255

erpsGroupInstance		1.3.6.1.4.1.10297.202.7000.3.16.2.1.2
The instance of ERPS group.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..8

erpsGroupRingId		1.3.6.1.4.1.10297.202.7000.3.16.2.1.3
The ring ID of ERPS group.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

erpsGroupRole		1.3.6.1.4.1.10297.202.7000.3.16.2.1.4
The role of ERPS group
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	rplowner(0), rplneighbor(1), other(2)

erpsGroupState		1.3.6.1.4.1.10297.202.7000.3.16.2.1.5
The current state of ERPS group.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

erpsGroupEastLink		1.3.6.1.4.1.10297.202.7000.3.16.2.1.6
The east link port of ERPS group. For trunk port : Trunk1 is 1000, Trunk2 is 1001, ...
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

erpsGroupEastLinkRPL		1.3.6.1.4.1.10297.202.7000.3.16.2.1.7
The rpl setting of ERPS group east link.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	rpl(1), n-rpl(2)

erpsGroupEastLinkState		1.3.6.1.4.1.10297.202.7000.3.16.2.1.8
The current state of ERPS group east link.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

erpsGroupWestLink		1.3.6.1.4.1.10297.202.7000.3.16.2.1.9
The west link port of ERPS group. For trunk port : Trunk1 is 1000, Trunk2 is 1001, ...
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..255

erpsGroupWestLinkRPL		1.3.6.1.4.1.10297.202.7000.3.16.2.1.10
The rpl setting of ERPS group west link
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	rpl(1), n-rpl(2)

erpsGroupWestLinkState		1.3.6.1.4.1.10297.202.7000.3.16.2.1.11
The current state of ERPS group west link.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

erpsGroupMEL		1.3.6.1.4.1.10297.202.7000.3.16.2.1.12
The MEL of ERPS group.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..7

erpsGroupRAPSChannelVlan		1.3.6.1.4.1.10297.202.7000.3.16.2.1.13
The r-aps channel vlan of ERPS group.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4094

erpsGroupTrafficChannel		1.3.6.1.4.1.10297.202.7000.3.16.2.1.14
The traffic channel of ERPS group.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..15

erpsGroupRevertive		1.3.6.1.4.1.10297.202.7000.3.16.2.1.15
The revertive setting of ERPS group.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	revertive(1), none-revertive(2)

erpsGroupType		1.3.6.1.4.1.10297.202.7000.3.16.2.1.16
The ring type of ERPS group.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	majorRing(1), subRing(2)

erpsGroupInterconnected		1.3.6.1.4.1.10297.202.7000.3.16.2.1.17
The interconnected setting of ERPS group.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	interconnected(1), none-interconnected(2)

erpsGroupChannel		1.3.6.1.4.1.10297.202.7000.3.16.2.1.18
The virtual channel setting of ERPS group.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	with-virtual-channel(1), without-virtual-channel(2)

erpsGroupTcPropagation		1.3.6.1.4.1.10297.202.7000.3.16.2.1.19
The tc-propagation setting of ERPS group.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tc-propagation(1), none-tc-propagation(2)

erpsWTRTimer		1.3.6.1.4.1.10297.202.7000.3.16.2.1.20
The WTR timer of ERPS group.(1 Unit = 1 minute)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..12

erpsGuardTimer		1.3.6.1.4.1.10297.202.7000.3.16.2.1.21
The guard timer of ERPS group.(1 Unit = 10 ms)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..200

erpsHoldOffTimer		1.3.6.1.4.1.10297.202.7000.3.16.2.1.22
The hold-off timer of ERPS group.(1 Unit = 100 ms)
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..100

erpsGroupRowStatus		1.3.6.1.4.1.10297.202.7000.3.16.2.1.99
User can use createRequest(2) to create new entry. After setup the value, user use valid(1) to set into switch. User can use destory to invalid(4) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	valid(1), createRequest(2), underCreation(3), invalid(4)

staticMacSetting		1.3.6.1.4.1.10297.202.7000.4.1
OBJECT IDENTIFIER

dynamicMacSetting		1.3.6.1.4.1.10297.202.7000.4.2
OBJECT IDENTIFIER

dynamicLearned		1.3.6.1.4.1.10297.202.7000.4.3
OBJECT IDENTIFIER

staticMacSettingTable		1.3.6.1.4.1.10297.202.7000.4.1.1
The table of static MAC setting
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		StaticMacSettingEntry

staticMacSettingEntry		1.3.6.1.4.1.10297.202.7000.4.1.1.1
The entry of static MAC setting
Status: current	Access: not-accessible
OBJECT-TYPE
	StaticMacSettingEntry

staticMacSettingIndex		1.3.6.1.4.1.10297.202.7000.4.1.1.1.1
The index of static MAC setting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..256

staticMacSettingMacAddress		1.3.6.1.4.1.10297.202.7000.4.1.1.1.2
The MAC address to which packets will be statically forwardef. It only supports unicast MAC address
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

staticMacSettingVlan		1.3.6.1.4.1.10297.202.7000.4.1.1.1.3
the VLAN which the static MAC belongs to
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4094

staticMacSettingPort		1.3.6.1.4.1.10297.202.7000.4.1.1.1.4
the port number of the MAC entry. For trunk port : Trunk1 is 1000, Trunk2 is 1001, ...
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

staticMacSettingRowStatus		1.3.6.1.4.1.10297.202.7000.4.1.1.1.99
User can use createAndWait(5) to create new entry. After setup the value, user use active(1) to set into switch. User can use destory to delete(6) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	active(1), notInService(2), createAndWait(5), destory(6)

macAgingTime		1.3.6.1.4.1.10297.202.7000.4.2.1
The dynamic MAC address aging out value
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	10..630

clearMacAddressTable		1.3.6.1.4.1.10297.202.7000.4.3.1
Clear the MAC table
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	clear(1)

macAddressInfoTable		1.3.6.1.4.1.10297.202.7000.4.3.2
The table of MAC address info
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MacAddressInfoEntry

macAddressInfoEntry		1.3.6.1.4.1.10297.202.7000.4.3.2.1
The entry of MAC address info
Status: current	Access: not-accessible
OBJECT-TYPE
	MacAddressInfoEntry

macAddressInfoIndex		1.3.6.1.4.1.10297.202.7000.4.3.2.1.1
The index of MAC address info
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

macAddressInfoMAC		1.3.6.1.4.1.10297.202.7000.4.3.2.1.2
The MAC address to show dynamic MAC entries.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

macAddressInfoVlan		1.3.6.1.4.1.10297.202.7000.4.3.2.1.3
The VLAN to show dynamic MAC entries.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

macAddressInfoType		1.3.6.1.4.1.10297.202.7000.4.3.2.1.4
The type of MAC address info
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	static(1), dynamic(2)

macAddressInfoPort		1.3.6.1.4.1.10297.202.7000.4.3.2.1.5
The port of MAC address info
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

addtoStaticMacTable		1.3.6.1.4.1.10297.202.7000.4.3.2.1.6
Add the entry from dynamic to static.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nothing(0), addtoStaticMac(1)

stormControl		1.3.6.1.4.1.10297.202.7000.5.1
OBJECT IDENTIFIER

protectedPort		1.3.6.1.4.1.10297.202.7000.5.2
OBJECT IDENTIFIER

dos		1.3.6.1.4.1.10297.202.7000.5.3
OBJECT IDENTIFIER

access		1.3.6.1.4.1.10297.202.7000.5.4
OBJECT IDENTIFIER

portSecurity		1.3.6.1.4.1.10297.202.7000.5.5
OBJECT IDENTIFIER

ipSecurity		1.3.6.1.4.1.10297.202.7000.5.6
OBJECT IDENTIFIER

ieee8021x		1.3.6.1.4.1.10297.202.7000.5.7
OBJECT IDENTIFIER

securityLogin		1.3.6.1.4.1.10297.202.7000.5.8
OBJECT IDENTIFIER

acl		1.3.6.1.4.1.10297.202.7000.5.9
OBJECT IDENTIFIER

ipSourceGuard		1.3.6.1.4.1.10297.202.7000.5.10
OBJECT IDENTIFIER

dhcpSnooping		1.3.6.1.4.1.10297.202.7000.5.11
OBJECT IDENTIFIER

arpSpoofing		1.3.6.1.4.1.10297.202.7000.5.12
OBJECT IDENTIFIER

stromControlUnit		1.3.6.1.4.1.10297.202.7000.5.1.1
The mode of stromg control. pps: strom control rate calculates by packet-based bps: strom control rate calculates by octet-based
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	pps(1), bps(2)

stromControlPreamble-IFG		1.3.6.1.4.1.10297.202.7000.5.1.2
the rate calculates w/o preamble & IFG (20 bytes) Excluded: exclude preamble & IFG (20 bytes) when count ingress storm control rate. Included: include preamble & IFG (20 bytes) when count ingress storm control rate.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	excluded(1), included(2)

stromControlPortTable		1.3.6.1.4.1.10297.202.7000.5.1.3
The table of port security setting
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PortSecSettingEntry

stromControlPortEntry		1.3.6.1.4.1.10297.202.7000.5.1.3.1
The entry of port security setting
Status: current	Access: not-accessible
OBJECT-TYPE
	PortSecSettingEntry

stromControlPortIndex		1.3.6.1.4.1.10297.202.7000.5.1.3.1.1
The port index of port security setting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

stromControlPortState		1.3.6.1.4.1.10297.202.7000.5.1.3.1.2
the state of setting
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

stromControlPortAction		1.3.6.1.4.1.10297.202.7000.5.1.3.1.3
the state of setting Drop: Packets exceed storm control rate will be droped. Shutdown: Port exceed storm control rate will be shutdown.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	drop(1), shutdown(2)

enablebroadcast		1.3.6.1.4.1.10297.202.7000.5.1.3.1.4
enable/diable the broadcast packet
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

broadcastRate		1.3.6.1.4.1.10297.202.7000.5.1.3.1.5
Value of storm control rate, Unit: pps (packet per-second) or Kbps (Kbits per-second) depends on global mode setting. The range is from 0 to 1000000.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..1000000

enableunknownMulticast		1.3.6.1.4.1.10297.202.7000.5.1.3.1.6
enable/diable the unknown multicast packet
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

unknownMulticastRate		1.3.6.1.4.1.10297.202.7000.5.1.3.1.7
Value of storm control rate, Unit: pps (packet per-second) or Kbps (Kbits per-second) depends on global mode setting. The range is from 0 to 1000000.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..1000000

enableunknownUnicast		1.3.6.1.4.1.10297.202.7000.5.1.3.1.8
enable/diable the unknown unicast packet
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

unknownUnicastRate		1.3.6.1.4.1.10297.202.7000.5.1.3.1.9
Value of storm control rate, Unit: pps (packet per-second) or Kbps (Kbits per-second) depends on global mode setting. The range is from 0 to 1000000.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..1000000

protectedPortTable		1.3.6.1.4.1.10297.202.7000.5.2.1
The table of protected port
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ProtectedPortEntry

protectedPortEntry		1.3.6.1.4.1.10297.202.7000.5.2.1.1
The entry of protected port
Status: current	Access: not-accessible
OBJECT-TYPE
	ProtectedPortEntry

protectedPortIndex		1.3.6.1.4.1.10297.202.7000.5.2.1.1.1
The port index of protected port
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

protectedPortType		1.3.6.1.4.1.10297.202.7000.5.2.1.1.2
Configure port protect type Unprotected: Unprotected port can communicate with all ports. Protected: Prevent protected ports from communication with each other.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	unprotected(1), porotected(2)

dmacEqualsmac		1.3.6.1.4.1.10297.202.7000.5.3.1
Both the source and the destination MAC addresses are the same
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

land		1.3.6.1.4.1.10297.202.7000.5.3.2
Both the source and the destination IPv4/IPv6 addresses are the same
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

udpBlat		1.3.6.1.4.1.10297.202.7000.5.3.3
Both the source and the destination UDP port are the same
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

tcpBlat		1.3.6.1.4.1.10297.202.7000.5.3.4
Both the source and the destination TCP port are the same
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

pod		1.3.6.1.4.1.10297.202.7000.5.3.5
Ping packets that length are larger than 65535 bytes
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ipv6MinFragment		1.3.6.1.4.1.10297.202.7000.5.3.6
IPv6 fragmented packets (not including the last one) that payload length less than 1240 bytes, and the Min length can be configured if needed.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ipv6MinFragmentValue		1.3.6.1.4.1.10297.202.7000.5.3.7
IPv6 fragmented packets (not including the last one) that payload length less than 1240 bytes, and the Min length can be configured if needed.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

icmpFragment		1.3.6.1.4.1.10297.202.7000.5.3.8
Fragmented ICMP packets.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ipv4PingMaxSize		1.3.6.1.4.1.10297.202.7000.5.3.9
IPv4 PING packet with the length
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ipv6PingMaxSize		1.3.6.1.4.1.10297.202.7000.5.3.10
IPv6 PING packet with the length
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

pingMaxSizeSetting		1.3.6.1.4.1.10297.202.7000.5.3.11
Ping packet Max Size Setting. The default value is 512 Bytes, it can be configured if needed.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..65535

smurfAttack		1.3.6.1.4.1.10297.202.7000.5.3.12
ICMP echo request packet that destination IPv4 address is broadcast address.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

smurfAttackValue		1.3.6.1.4.1.10297.202.7000.5.3.13
The default Netmask length is 0, and it can be configured if needed.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..32

tcpMinHdrSize		1.3.6.1.4.1.10297.202.7000.5.3.14
TCP packet that header length is less than the configured value.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

tcpMinHdrSizeValue		1.3.6.1.4.1.10297.202.7000.5.3.15
The default TCP Min Hdr Size is 20, it can be configured if needed.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..31

tcp-Syn		1.3.6.1.4.1.10297.202.7000.5.3.16
TCP SYN packets with source port less than 1024.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

nullScanAttack		1.3.6.1.4.1.10297.202.7000.5.3.17
TCP sequence number is zero, and all control flags are zeroes.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

xMasScanAttack		1.3.6.1.4.1.10297.202.7000.5.3.18
TCP sequence number is zero, and the FIN/URG/PSH flags are set.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

tcpSYN-FINAttack		1.3.6.1.4.1.10297.202.7000.5.3.19
A TCP packet with the SYN and FIN flags set.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

tcpSYN-RSTAttack		1.3.6.1.4.1.10297.202.7000.5.3.20
A TCP packet with the SYN and RST flags set.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

tcpFragment		1.3.6.1.4.1.10297.202.7000.5.3.21
Fragmented TCP packets.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

dosPortTable		1.3.6.1.4.1.10297.202.7000.5.3.22
The table of DoS port
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DosPortEntry

dosPortEntry		1.3.6.1.4.1.10297.202.7000.5.3.22.1
The entry of DoS port
Status: current	Access: not-accessible
OBJECT-TYPE
	DosPortEntry

dosportIndex		1.3.6.1.4.1.10297.202.7000.5.3.22.1.1
The port index of DoS port
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

dosProtection		1.3.6.1.4.1.10297.202.7000.5.3.22.1.2
Configure port protect state
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

telnetInfo		2.1
OBJECT IDENTIFIER

telnetService		2.1.1
enable/disable the tlent service
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

currentTelnetSessionCount		2.1.2
The current telnet session counter
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

httpSetting		2.2
OBJECT IDENTIFIER

httpService		2.2.1
enable/disable the http service
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

httpSessionTimeout		2.2.2
the HTTP session timeout
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..86400

httpsSetting		2.3
OBJECT IDENTIFIER

httpsService		2.3.1
enable/disable the https service
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

httpsSessionTimeout		2.3.2
the HTTPs session timeout
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..86400

sshInfo		2.4
OBJECT IDENTIFIER

sshService		2.4.1
enable/disable the ssh service
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

portSecurityTable		1.3.6.1.4.1.10297.202.7000.5.5.1
The table of port security
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PortSecurityEntry

portSecurityEntry		1.3.6.1.4.1.10297.202.7000.5.5.1.1
The entry of port security
Status: current	Access: not-accessible
OBJECT-TYPE
	PortSecurityEntry

portSecurityPortIndex		1.3.6.1.4.1.10297.202.7000.5.5.1.1.1
The port index of port security
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

portSecurityEnabled		1.3.6.1.4.1.10297.202.7000.5.5.1.1.2
Enable/Disable port security
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

portSecurityFDBLimit		1.3.6.1.4.1.10297.202.7000.5.5.1.1.3
The number of FDB learning.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..64

portSecurityViolationMACNotify		1.3.6.1.4.1.10297.202.7000.5.5.1.1.4
Enable/Disable Violation MAC Notification
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

ipSecurityStatus		1.3.6.1.4.1.10297.202.7000.5.6.1
Enable/Disable IP security
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

ipSecurityTable		1.3.6.1.4.1.10297.202.7000.5.6.2
The table of IP security
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IPSecurityEntry

ipSecurityEntry		1.3.6.1.4.1.10297.202.7000.5.6.2.1
The entry of IP security
Status: current	Access: not-accessible
OBJECT-TYPE
	IPSecurityEntry

ipSecurityIndex		1.3.6.1.4.1.10297.202.7000.5.6.2.1.1
The index of IP security
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..10

ipSecurityIPAddr		1.3.6.1.4.1.10297.202.7000.5.6.2.1.2
The IP address of IP security
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

ipSecurityIPMask		1.3.6.1.4.1.10297.202.7000.5.6.2.1.3
The IP mask of IP security
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

ipSecurityService		1.3.6.1.4.1.10297.202.7000.5.6.2.1.4
The service of IP security
Status: current	Access: read-write
OBJECT-TYPE
	BITS	ping(0), http(1), telnet(2), ssh(3), snmp(4)

ipSecurityVlanId		1.3.6.1.4.1.10297.202.7000.5.6.2.1.5
The VLAN id of IP security. This value will appear on multiple interface.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4094

ipSecurityRowStatus		1.3.6.1.4.1.10297.202.7000.5.6.2.1.99
User can use createAndWait(5) to create new entry. After setup the value, user use active(1) to set into switch. User can use destory to delete(6) an entry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), notInService(2), createAndWait(5), destory(6)

ieee8021xState		1.3.6.1.4.1.10297.202.7000.5.7.1
Enable/Disable IEEE 802.1x
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

ieee8021xServerIP		1.3.6.1.4.1.10297.202.7000.5.7.2
The server IP address of IEEE 802.1x
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

ieee8021xServerPort		1.3.6.1.4.1.10297.202.7000.5.7.3
The server port of IEEE 802.1x
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

ieee8021xAccountingPort		1.3.6.1.4.1.10297.202.7000.5.7.4
The accounting port of IEEE 802.1x
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

ieee8021xSecurityKey		1.3.6.1.4.1.10297.202.7000.5.7.5
The security key of IEEE 802.1x
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

ieee8021xReauthPeriod		1.3.6.1.4.1.10297.202.7000.5.7.6
The reauth period of IEEE 802.1x
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

ieee8021xPortTable		1.3.6.1.4.1.10297.202.7000.5.7.7
The table of IEEE 802.1x
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IEEE8021xPortEntry

ieee8021xPortEntry		1.3.6.1.4.1.10297.202.7000.5.7.7.1
The entry of IEEE 802.1x
Status: current	Access: not-accessible
OBJECT-TYPE
	IEEE8021xPortEntry

ieee8021xPortIndex		1.3.6.1.4.1.10297.202.7000.5.7.7.1.1
The index of IEEE 802.1x
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

ieee8021xPortState		1.3.6.1.4.1.10297.202.7000.5.7.7.1.2
The port state of IEEE 802.1x
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	authorize(1), disabled(2)

ieee8021xAuthBased		1.3.6.1.4.1.10297.202.7000.5.7.8
The authentication based of IEEE 802.1x
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	port(1), mac(2), mac-auth-bypass(3)

securityLoginState		1.3.6.1.4.1.10297.202.7000.5.8.1
Enable/Disable security login.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

radiusServer		1.3.6.1.4.1.10297.202.7000.5.8.2
OBJECT IDENTIFIER

radiusServerIP		1.3.6.1.4.1.10297.202.7000.5.8.2.1
Radius server IP.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

radiusServerPort		1.3.6.1.4.1.10297.202.7000.5.8.2.2
Radius server port.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

radiusServerSecurityKey		1.3.6.1.4.1.10297.202.7000.5.8.2.3
The security key of radius server.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

tacacsServer		1.3.6.1.4.1.10297.202.7000.5.8.3
OBJECT IDENTIFIER

tacacsServerIP		1.3.6.1.4.1.10297.202.7000.5.8.3.1
TACACS server IP.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

tacacsServerPort		1.3.6.1.4.1.10297.202.7000.5.8.3.2
TACACS server port.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

tacacsServerSecurityKey		1.3.6.1.4.1.10297.202.7000.5.8.3.3
The security key of TACACS server.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

securityLoginType		1.3.6.1.4.1.10297.202.7000.5.8.4
Enable/Disable security login.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(0), radius(1), tacacs(2), radiusAndtacacs(3), radiusAndtacacsAndweb(4)

securityLoginHttpState		1.3.6.1.4.1.10297.202.7000.5.8.5
Enable/Disable HTTP type of security login.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

securityLoginTelnetState		1.3.6.1.4.1.10297.202.7000.5.8.6
Enable/Disable telnet type of security login.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

securityLoginSSHState		1.3.6.1.4.1.10297.202.7000.5.8.7
Enable/Disable SSH type of security login.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

macAclTable		1.3.6.1.4.1.10297.202.7000.5.9.1
The table of mac acl
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		MacAclEntry

macAclEntry		1.3.6.1.4.1.10297.202.7000.5.9.1.1
The entry of mac acl
Status: current	Access: not-accessible
OBJECT-TYPE
	MacAclEntry

macAclIndex		1.3.6.1.4.1.10297.202.7000.5.9.1.1.1
The index of mac ACL entry
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..250

destinationMacAddress		1.3.6.1.4.1.10297.202.7000.5.9.1.1.2
The destination MAC address of mac ACL entry.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

destinationMacMask		1.3.6.1.4.1.10297.202.7000.5.9.1.1.3
The destination MAC mask of mac ACL entry.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sourceMacAddress		1.3.6.1.4.1.10297.202.7000.5.9.1.1.4
The source MAC address of mac ACL entry.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sourceMacMask		1.3.6.1.4.1.10297.202.7000.5.9.1.1.5
The source MAC mask of mac ACL entry.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

macAclEtherType		1.3.6.1.4.1.10297.202.7000.5.9.1.1.6
The ether type of mac ACL entry
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

macAclVlanID		1.3.6.1.4.1.10297.202.7000.5.9.1.1.7
The vlan id of mac ACL entry
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4094

macAclPortList		1.3.6.1.4.1.10297.202.7000.5.9.1.1.8
The port list of mac ACL entry.
Status: current	Access: read-write
OBJECT-TYPE
	BITS	port1(0), port2(1), port3(2), port4(3), port5(4), port6(5), port7(6), port8(7), port9(8), port10(9), port11(10), port12(11), port13(12), port14(13), port15(14), port16(15), port17(16), port18(17), port19(18), port20(19), port21(20), port22(21), port23(22), port24(23), port25(24), port26(25), port27(26), port28(27), port29(28), port30(29), port31(30), port32(31)

macAclAction		1.3.6.1.4.1.10297.202.7000.5.9.1.1.9
The action of mac ACL entry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	permit(1), drop(2)

macAclActiveStatus		1.3.6.1.4.1.10297.202.7000.5.9.1.1.10
The active status of mac ACL entry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), inactive(2)

macAclRowStatus		1.3.6.1.4.1.10297.202.7000.5.9.1.1.99
User can use createRequest(2) to create new entry. After setup the value, user use valid(1) to set into switch. User can use destory to invalid(4) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	valid(1), createRequest(2), underCreation(3), invalid(4)

ipAclTable		1.3.6.1.4.1.10297.202.7000.5.9.2
The table of ip acl
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpAclEntry

ipAclEntry		1.3.6.1.4.1.10297.202.7000.5.9.2.1
The entry of ip acl
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAclEntry

ipAclIndex		1.3.6.1.4.1.10297.202.7000.5.9.2.1.1
The index of ip ACL entry
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..250

destinationIpAddress		1.3.6.1.4.1.10297.202.7000.5.9.2.1.2
The destination ip address of ip ACL entry.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

destinationIpMask		1.3.6.1.4.1.10297.202.7000.5.9.2.1.3
The destination ip mask of ip ACL entry.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

sourceIpAddress		1.3.6.1.4.1.10297.202.7000.5.9.2.1.4
The source ip address of ip ACL entry.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

sourceIpMask		1.3.6.1.4.1.10297.202.7000.5.9.2.1.5
The source ip mask of ip ACL entry.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

ipProtocol		1.3.6.1.4.1.10297.202.7000.5.9.2.1.6
The ip protocol of ip ACL entry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), icmp(2), tcp(3), udp(4)

l4DestinationPort		1.3.6.1.4.1.10297.202.7000.5.9.2.1.7
The L4 destination port of ip ACL entry
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

l4SourcePort		1.3.6.1.4.1.10297.202.7000.5.9.2.1.8
The L4 source port of ip ACL entry
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

ipAclPortList		1.3.6.1.4.1.10297.202.7000.5.9.2.1.9
The port list of ip ACL entry.
Status: current	Access: read-write
OBJECT-TYPE
	BITS	port1(0), port2(1), port3(2), port4(3), port5(4), port6(5), port7(6), port8(7), port9(8), port10(9), port11(10), port12(11), port13(12), port14(13), port15(14), port16(15), port17(16), port18(17), port19(18), port20(19), port21(20), port22(21), port23(22), port24(23), port25(24), port26(25), port27(26), port28(27), port29(28), port30(29), port31(30), port32(31)

ipAclAction		1.3.6.1.4.1.10297.202.7000.5.9.2.1.10
The action of ip ACL entry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	permit(1), drop(2)

ipAclActiveStatus		1.3.6.1.4.1.10297.202.7000.5.9.2.1.11
The active status of ip ACL entry.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), inactive(2)

ipAclRowStatus		1.3.6.1.4.1.10297.202.7000.5.9.2.1.99
User can use createRequest(2) to create new entry. After setup the value, user use valid(1) to set into switch. User can use destory to invalid(4) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	valid(1), createRequest(2), underCreation(3), invalid(4)

ipSourceGuardEnablePorts		1.3.6.1.4.1.10297.202.7000.5.10.1
The enable port list for ip source guard.
Status: current	Access: read-write
OBJECT-TYPE
	BITS	port1(0), port2(1), port3(2), port4(3), port5(4), port6(5), port7(6), port8(7), port9(8), port10(9), port11(10), port12(11), port13(12), port14(13), port15(14), port16(15), port17(16), port18(17), port19(18), port20(19), port21(20), port22(21), port23(22), port24(23), port25(24), port26(25), port27(26), port28(27), port29(28), port30(29), port31(30), port32(31)

ipSourceGuardTable		1.3.6.1.4.1.10297.202.7000.5.10.2
The table of ip source guard
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpSourceGuardEntry

ipSourceGuardEntry		1.3.6.1.4.1.10297.202.7000.5.10.2.1
The entry of ip source guard
Status: current	Access: not-accessible
OBJECT-TYPE
	IpSourceGuardEntry

ipSourceGuardIndex		1.3.6.1.4.1.10297.202.7000.5.10.2.1.1
The index of ip source guard entry
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..64

ipSourceGuardSourceIp		1.3.6.1.4.1.10297.202.7000.5.10.2.1.2
The destination ip address of ip source guard entry.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

ipSourceGuardSourceMac		1.3.6.1.4.1.10297.202.7000.5.10.2.1.3
The destination MAC address of ip source guard entry.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

ipSourceGuardPort		1.3.6.1.4.1.10297.202.7000.5.10.2.1.4
The port of ip source guard entry
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

ipSourceGuardRowStatus		1.3.6.1.4.1.10297.202.7000.5.10.2.1.5
User can use createRequest(2) to create new entry. After setup the value, user use valid(1) to set into switch. User can use destory to invalid(4) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	valid(1), createRequest(2), underCreation(3), invalid(4)

dhcpSnoopingState		1.3.6.1.4.1.10297.202.7000.5.11.1
Enable/Disable DHCP snooping.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

dhcpSnoopingPorts		1.3.6.1.4.1.10297.202.7000.5.11.2
The enable port list for dhcp snooping.
Status: current	Access: read-write
OBJECT-TYPE
	BITS	port1(0), port2(1), port3(2), port4(3), port5(4), port6(5), port7(6), port8(7), port9(8), port10(9), port11(10), port12(11), port13(12), port14(13), port15(14), port16(15), port17(16), port18(17), port19(18), port20(19), port21(20), port22(21), port23(22), port24(23), port25(24), port26(25), port27(26), port28(27), port29(28), port30(29), port31(30), port32(31)

dhcpSnoopingBindingPorts		1.3.6.1.4.1.10297.202.7000.5.11.3
The enable blinding port list for dhcp snooping.
Status: current	Access: read-write
OBJECT-TYPE
	BITS	port1(0), port2(1), port3(2), port4(3), port5(4), port6(5), port7(6), port8(7), port9(8), port10(9), port11(10), port12(11), port13(12), port14(13), port15(14), port16(15), port17(16), port18(17), port19(18), port20(19), port21(20), port22(21), port23(22), port24(23), port25(24), port26(25), port27(26), port28(27), port29(28), port30(29), port31(30), port32(31)

dhcpSnoopingTable		1.3.6.1.4.1.10297.202.7000.5.11.4
The table of dhcp snooping
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DhcpSnoopingEntry

dhcpSnoopingEntry		1.3.6.1.4.1.10297.202.7000.5.11.4.1
The entry of dhcp snooping
Status: current	Access: not-accessible
OBJECT-TYPE
	DhcpSnoopingEntry

dhcpSnoopingIndex		1.3.6.1.4.1.10297.202.7000.5.11.4.1.1
The index of dhcp snooping entry
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..64

dhcpSnoopingMac		1.3.6.1.4.1.10297.202.7000.5.11.4.1.2
The destination MAC address of dhcp snooping entry.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

dhcpSnoopingIp		1.3.6.1.4.1.10297.202.7000.5.11.4.1.3
The destination ip address of dhcp snooping entry.
Status: current	Access: read-only
OBJECT-TYPE
	IpAddress

dhcpSnoopingLeaseTime		1.3.6.1.4.1.10297.202.7000.5.11.4.1.4
The lease time of dhcp snooping entry
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	60..864000

dhcpSnoopingVlanId		1.3.6.1.4.1.10297.202.7000.5.11.4.1.5
The VLAN ID of dhcp snooping entry
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..4094

dhcpSnoopingPort		1.3.6.1.4.1.10297.202.7000.5.11.4.1.6
The port of dhcp snooping entry
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

arpSpoofingTable		1.3.6.1.4.1.10297.202.7000.5.12.1
The table of arp spoofing
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ArpSpoofingEntry

arpSpoofingEntry		1.3.6.1.4.1.10297.202.7000.5.12.1.1
The entry of arp spoofing
Status: current	Access: not-accessible
OBJECT-TYPE
	ArpSpoofingEntry

arpSpoofingIndex		1.3.6.1.4.1.10297.202.7000.5.12.1.1.1
The index of arp spoofing entry
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..64

arpSpoofingSourceMac		1.3.6.1.4.1.10297.202.7000.5.12.1.1.2
The source MAC address of arp spoofing entry.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

arpSpoofingSourceIp		1.3.6.1.4.1.10297.202.7000.5.12.1.1.3
The source ip address of arp spoofing entry.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

arpSpoofingRowStatus		1.3.6.1.4.1.10297.202.7000.5.12.1.1.4
User can use createRequest(2) to create new entry. After setup the value, user use valid(1) to set into switch. User can use destory to invalid(4) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	valid(1), createRequest(2), underCreation(3), invalid(4)

general		1.3.6.1.4.1.10297.202.7000.6.1
OBJECT IDENTIFIER

qosBasicMode		1.3.6.1.4.1.10297.202.7000.6.2
OBJECT IDENTIFIER

rateLimit		1.3.6.1.4.1.10297.202.7000.6.3
OBJECT IDENTIFIER

qosMode		1.3.6.1.4.1.10297.202.7000.6.1.1
The QoS operaion mode
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	basic(1), disable(2)

qosPortSettingTable		1.3.6.1.4.1.10297.202.7000.6.1.2
The table of QoS port setting
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QosPortSettingEntry

qosPortSettingEntry		1.3.6.1.4.1.10297.202.7000.6.1.2.1
The entry of QoS port setting
Status: current	Access: not-accessible
OBJECT-TYPE
	QosPortSettingEntry

qosPortIndex		1.3.6.1.4.1.10297.202.7000.6.1.2.1.1
The port index of QoS port setting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

qosPortCos		1.3.6.1.4.1.10297.202.7000.6.1.2.1.2
The default CoS/802.1p priority value
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..7

qosPortRemarkCoS		1.3.6.1.4.1.10297.202.7000.6.1.2.1.3
enable/disable CoS remark
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

qosPortRemarkDSCP		1.3.6.1.4.1.10297.202.7000.6.1.2.1.4
enable/disable DSCP remark
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

qosPortRemarkIPPrecedence		1.3.6.1.4.1.10297.202.7000.6.1.2.1.5
Enable/Disable IP Precedence remark
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

queueSettingTable		1.3.6.1.4.1.10297.202.7000.6.1.3
The table of queue setting
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QueueSettingEntry

queueSettingEntry		1.3.6.1.4.1.10297.202.7000.6.1.3.1
the entry of queue setting
Status: current	Access: not-accessible
OBJECT-TYPE
	QueueSettingEntry

queueIndex		1.3.6.1.4.1.10297.202.7000.6.1.3.1.1
The index of queue setting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..8

queueMethod		1.3.6.1.4.1.10297.202.7000.6.1.3.1.2
queue to strict priority type or Weight round robin type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	strictPriority(1), wrr(2)

queueWeight		1.3.6.1.4.1.10297.202.7000.6.1.3.1.3
If the queue type is WRR, set the queue weight for the queue.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

queuePercentOfWRRBandwidth		1.3.6.1.4.1.10297.202.7000.6.1.3.1.4
The percentage of the WRR bandwidth
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

costoQueueMapTable		1.3.6.1.4.1.10297.202.7000.6.1.4
The table of CoS to queue
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CostoQueueMapEntry

costoQueueMapEntry		1.3.6.1.4.1.10297.202.7000.6.1.4.1
The entry of CoS to queue
Status: current	Access: not-accessible
OBJECT-TYPE
	CostoQueueMapEntry

cosIndex		1.3.6.1.4.1.10297.202.7000.6.1.4.1.1
The index of CoS to queue
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..8

cosQueue		1.3.6.1.4.1.10297.202.7000.6.1.4.1.2
The queue of CoS to queue
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..8

queuetoCosMapTable		1.3.6.1.4.1.10297.202.7000.6.1.5
The table of queue to CoS
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QueueToCosMapEntry

queuetoCosMapEntry		1.3.6.1.4.1.10297.202.7000.6.1.5.1
The entry of queue to CoS
Status: current	Access: not-accessible
OBJECT-TYPE
	QueueToCosMapEntry

queuetoCosIndex		1.3.6.1.4.1.10297.202.7000.6.1.5.1.1
The queue index of queue to CoS
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..8

queueCos		1.3.6.1.4.1.10297.202.7000.6.1.5.1.2
The cos of queue to CoS
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..7

dscptoQueueMapTable		1.3.6.1.4.1.10297.202.7000.6.1.6
The table of DSCP to queue
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DscptoQueueMapEntry

dscptoQueueMapEntry		1.3.6.1.4.1.10297.202.7000.6.1.6.1
The entry of DSCP to queue
Status: current	Access: not-accessible
OBJECT-TYPE
	DscptoQueueMapEntry

dscpIndex		1.3.6.1.4.1.10297.202.7000.6.1.6.1.1
The DSCP index of DSCP to queue
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..64

dscpQueue		1.3.6.1.4.1.10297.202.7000.6.1.6.1.2
The queue of DSCP to queue
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..8

queuetoDSCPMapTable		1.3.6.1.4.1.10297.202.7000.6.1.7
The table of queue to DSCP
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QueuetoDSCPMapEntry

queuetoDSCPMapEntry		1.3.6.1.4.1.10297.202.7000.6.1.7.1
The entry of queue to DSCP
Status: current	Access: not-accessible
OBJECT-TYPE
	QueuetoDSCPMapEntry

queuetoDSCPIndex		1.3.6.1.4.1.10297.202.7000.6.1.7.1.1
The queue index of queue to DSCP
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..8

queuDscp		1.3.6.1.4.1.10297.202.7000.6.1.7.1.2
The DSCP of queue to DSCP
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..63

ipPrecedencetoQueueMapTable		1.3.6.1.4.1.10297.202.7000.6.1.8
The table of IP precedence to queue
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IpPrecedencetoQueueMapEntry

ipPrecedencetoQueueMapEntry		1.3.6.1.4.1.10297.202.7000.6.1.8.1
The entry of IP precedence to queue
Status: current	Access: not-accessible
OBJECT-TYPE
	IpPrecedencetoQueueMapEntry

ipPrecedenceIndex		1.3.6.1.4.1.10297.202.7000.6.1.8.1.1
The index of IP precedence to queue
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..8

ipPrecedenceQueue		1.3.6.1.4.1.10297.202.7000.6.1.8.1.2
The queue of IP precedence to queue
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..8

queueToipPrecedenceMapTable		1.3.6.1.4.1.10297.202.7000.6.1.9
The table of queue to IP precedence
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QueueToipPrecedenceMapEntry

queueToipPrecedenceMapEntry		1.3.6.1.4.1.10297.202.7000.6.1.9.1
The entry of queue to IP precedence
Status: current	Access: not-accessible
OBJECT-TYPE
	QueueToipPrecedenceMapEntry

queueToipPrecedenceIndex		1.3.6.1.4.1.10297.202.7000.6.1.9.1.1
The index of queue to IP precedence
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..8

ipPrecedence		1.3.6.1.4.1.10297.202.7000.6.1.9.1.2
The IP precedence of queue to IP precedence
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..7

trustMode		1.3.6.1.4.1.10297.202.7000.6.2.1
the QoS operation mode. CoS/802.1p: Traffic is mapped to queues based on the CoS field in the VLAN tag, or based on the per-port default CoS value if there is no VLAN tag on the incoming packet. DSCP: All IP traffic is mapped to queues based on the DSCP field in the IP header. If traffic is not IP traffic, it is mapped to the lowest priority queue. CoS/802.1p-DSCP: All IP traffic is mapped to queues based on the DSCP field in the IP header. If traffic is not IP but has VLAN tag, mapped to queues based on the CoS value in the VLAN tag. IP Precedence: All IP traffic is mapped to queues based on the IP Precedence field in the IP header. If traffic is not IP traffic, it is mapped to the lowest priority queue. None: All traffic is mapped to the lowest priority queue.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	cos-8021p(1), dscp(2), cos8021p-dscp(3), ip-precendence(4), none(5)

qosBasicPortTable		1.3.6.1.4.1.10297.202.7000.6.2.2
The table of QoS port
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		QosPortEntry

qosBasicPortEntry		1.3.6.1.4.1.10297.202.7000.6.2.2.1
The entry of QoS port
Status: current	Access: not-accessible
OBJECT-TYPE
	QosPortEntry

qosBasicPortIndex		1.3.6.1.4.1.10297.202.7000.6.2.2.1.1
The port index of QoS port
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

qosBasicPortTrust		1.3.6.1.4.1.10297.202.7000.6.2.2.1.2
the port trust state Enabled: Traffic from this port will follow the global trust type. Disabled: Traffic will always go to the lowest priority queue.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ingressBandwidthControl		1.3.6.1.4.1.10297.202.7000.6.3.1
OBJECT IDENTIFIER

ingressBandwidthTable		1.3.6.1.4.1.10297.202.7000.6.3.1.1
The table of ingress bandwidth
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		IngressBandwidthEntry

ingressBandwidthEntry		1.3.6.1.4.1.10297.202.7000.6.3.1.1.1
The entry of ingress bandwidth
Status: current	Access: not-accessible
OBJECT-TYPE
	IngressBandwidthEntry

ingressBandwidthPortIndex		1.3.6.1.4.1.10297.202.7000.6.3.1.1.1.1
The port index of ingress bandwidth
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

ingressBandwidthState		1.3.6.1.4.1.10297.202.7000.6.3.1.1.1.2
enable/disable ingress bandwidth control
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ingressBandwidthRate		1.3.6.1.4.1.10297.202.7000.6.3.1.1.1.3
rate value, unit:16Kbps
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	16..1000000

egressBandwidthControl		1.3.6.1.4.1.10297.202.7000.6.3.2
OBJECT IDENTIFIER

egressBandwidthTable		1.3.6.1.4.1.10297.202.7000.6.3.2.1
The table of egress bandwidth
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EgressBandwidthEntry

egressBandwidthEntry		1.3.6.1.4.1.10297.202.7000.6.3.2.1.1
The entry of egress bandwidth
Status: current	Access: not-accessible
OBJECT-TYPE
	EgressBandwidthEntry

egressBandwidthPortIndex		1.3.6.1.4.1.10297.202.7000.6.3.2.1.1.1
The port index of egress bandwidth
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

egressBandwidthState		1.3.6.1.4.1.10297.202.7000.6.3.2.1.1.2
enable/disable egress bandwidth control
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

egressBandwidthRate		1.3.6.1.4.1.10297.202.7000.6.3.2.1.1.3
rate value, unit:16Kbps
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..1000000

egressQueueBandwidthControl		1.3.6.1.4.1.10297.202.7000.6.3.3
OBJECT IDENTIFIER

egressqueueBandwidthTable		1.3.6.1.4.1.10297.202.7000.6.3.3.1
The table of egress queue bandwidth
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EgressqueueBandwidthEntry

egressqueueBandwidthEntry		1.3.6.1.4.1.10297.202.7000.6.3.3.1.1
The entry of egress queue bandwidth
Status: current	Access: not-accessible
OBJECT-TYPE
	EgressqueueBandwidthEntry

egressqueueBandwidthPortIndex		1.3.6.1.4.1.10297.202.7000.6.3.3.1.1.1
The port index of egress queue bandwidth
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

egressqueueBandwidthQueueIndex		1.3.6.1.4.1.10297.202.7000.6.3.3.1.1.2
The queue index of egress queue bandwidth
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..8

egressqueueBandwidthState		1.3.6.1.4.1.10297.202.7000.6.3.3.1.1.3
enable/disable egress bandwidth contro
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

egressqueueBandwidthCir		1.3.6.1.4.1.10297.202.7000.6.3.3.1.1.4
rate value, unit:16Kbps
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	16..1000000

lldp		1.3.6.1.4.1.10297.202.7000.7.1
OBJECT IDENTIFIER

snmp		1.3.6.1.4.1.10297.202.7000.7.2
OBJECT IDENTIFIER

poe		1.3.6.1.4.1.10297.202.7000.7.3
OBJECT IDENTIFIER

tcpModbus		1.3.6.1.4.1.10297.202.7000.7.4
OBJECT IDENTIFIER

dhcpServer		1.3.6.1.4.1.10297.202.7000.7.5
OBJECT IDENTIFIER

smtpClient		1.3.6.1.4.1.10297.202.7000.7.6
OBJECT IDENTIFIER

rmon		1.3.6.1.4.1.10297.202.7000.7.7
OBJECT IDENTIFIER

ntp		1.3.6.1.4.1.10297.202.7000.7.8
OBJECT IDENTIFIER

lldpEnabled		1.3.6.1.4.1.10297.202.7000.7.1.1
Enable/Disable LLDP protocol on this switch
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

lldpPduDisableAction		1.3.6.1.4.1.10297.202.7000.7.1.2
Select LLDP PDU handling action to be filtered, bridging or flooded when LLDP is globally disabled.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	filtering(1), bridging(2), flooding(3)

lldpTransmissionInterval		1.3.6.1.4.1.10297.202.7000.7.1.3
The interval at which frames are transmitted. LLDP transmission interval multiplies holdtme multiplier should be smaller than 65535. LLDP transmission delay should not be larger than LLDP transmission interval * 0.25
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	5..32767

lldpHoldtimeMultiplier		1.3.6.1.4.1.10297.202.7000.7.1.4
The multiplier on the transmit interval to assign to TTL. LLDP transmission interval multiplies holdtme multiplier should be smaller than 65535.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	2..10

lldpReinitializationDelay		1.3.6.1.4.1.10297.202.7000.7.1.5
The delay before a re-initialization
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..10

lldpTransmitDelay		1.3.6.1.4.1.10297.202.7000.7.1.6
The delay after an LLDP frame is sent. LLDP transmission delay should not be larger than LLDP transmission interval * 0.25
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..8191

lldpPortConfTable		1.3.6.1.4.1.10297.202.7000.7.1.7
The table of LLDP port configuration
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LldpPortConfEntry

lldpPortConfEntry		1.3.6.1.4.1.10297.202.7000.7.1.7.1
The entry of LLDP port configuration
Status: current	Access: not-accessible
OBJECT-TYPE
	LldpPortConfEntry

lldpPortIndex		1.3.6.1.4.1.10297.202.7000.7.1.7.1.1
The port index of LLDP port configuration
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

lldpPortState		1.3.6.1.4.1.10297.202.7000.7.1.7.1.2
the transmission state of LLDP port interface. Disable: Disable the transmission of LLDP PDUs. RX Only: Receive LLDP PDUs only. TX Only: Transmit LLDP PDUs only. TX And RX: Transmit and receive LLDP PDUs both.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	disable(1), rx-only(2), tx-only(3), rx-tx(4)

lldpPortOptionalTLVs		1.3.6.1.4.1.10297.202.7000.7.1.7.1.3
The LLDP optional TLVs to be carried
Status: current	Access: read-write
OBJECT-TYPE
	BITS	systemName(0), portDescription(1), systemDescription(2), systemCapability(3), ieee8023MAC-PHY(4), ieee8023LinkAggeration(5), ieee8023MaxFrameSize(6), managementAddress(7), ieee8021PVID(8)

lldpPortVlans		1.3.6.1.4.1.10297.202.7000.7.1.7.1.4
The VLAN name ID to be carried. User can inpu vlan such as: 1-2, 100.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

localDevice		1.3.6.1.4.1.10297.202.7000.7.1.8
OBJECT IDENTIFIER

lldpLocalDeviceChassisidsubtype		1.3.6.1.4.1.10297.202.7000.7.1.8.1
LLDP local device chassis ID subtype
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalDeviceChassisID		1.3.6.1.4.1.10297.202.7000.7.1.8.2
LLDP local device chassis ID
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalDeviceSystemName		1.3.6.1.4.1.10297.202.7000.7.1.8.3
LLDP local device system name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalDeviceSystemDescription		1.3.6.1.4.1.10297.202.7000.7.1.8.4
LLDP local device system description
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalDeviceCapabilitiesSupported		1.3.6.1.4.1.10297.202.7000.7.1.8.5
LLDP local device capabilities supported
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalDeviceCapabilitiesEnabled		1.3.6.1.4.1.10297.202.7000.7.1.8.6
LLDP local device capabilities enabled
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalDevicePortIDsubtype		1.3.6.1.4.1.10297.202.7000.7.1.8.7
LLDP local device port ID subtype
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortStatusTable		1.3.6.1.4.1.10297.202.7000.7.1.8.8
The table of LLFP local port status
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LldpLocalPortStatusEntry

lldpLocalPortStatusEntry		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1
The entry of LLFP local port status
Status: current	Access: not-accessible
OBJECT-TYPE
	LldpLocalPortStatusEntry

lldpLocalPortIndex		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.1
The port index of LLDP local port status
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

lldpLocalPortStatus		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.2
LLDP local port status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	disable(1), rx-only(2), tx-only(3), rx-tx(4)

lldpLocalPortChassisIDsubtype		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.3
LLDP local port chassis ID subtype
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortChassisID		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.4
LLDP local port chassis ID
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortSystemname		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.5
LLDP local port system name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortSystemdescription		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.6
LLDP local port system description
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortSupportedsystemcapabilities		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.7
LLDP local port supported system capabilities
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortEnablesystemcapabilities		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.8
LLDP local port enable system capabilities
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortIDsubtype		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.9
LLDP local port ID subtype
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortID		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.10
LLDP local port ID
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortDescription		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.11
LLDP local port description
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortManagementAddress		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.12
LLDP local port management address
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortAuto-negosupported		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.13
LLDP local port auto-nego supported
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortAuto-negoenabled		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.14
LLDP local port auto-nego enabled
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortAuto-negoAdvertisedCapabilities		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.15
LLDP local port auto-nego advertised capabilities
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortOperationMAUtype		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.16
LLDP local port operation MAU type
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortIeee8023MaxFrameSize		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.17
LLDP local port IEEE 802.3 max frame size
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortAggregationCapability		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.18
LLDP local port aggregation capabilities
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortAggregationStatus		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.19
LLDP local port aggregation status
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortAggregationPortID		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.20
LLDP local port aggregation port ID
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortPvid		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.21
LLDP local port PVID
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpLocalPortVlanName		1.3.6.1.4.1.10297.202.7000.7.1.8.8.1.22
LLDP local port vlan name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

remoteDevice		1.3.6.1.4.1.10297.202.7000.7.1.9
OBJECT IDENTIFIER

lldpremoteDeviceTable		1.3.6.1.4.1.10297.202.7000.7.1.9.1
The table of LLDP remote device
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LldpremoteDeviceEntry

lldpremoteDeviceEntry		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1
The entry of LLDP remote device
Status: current	Access: not-accessible
OBJECT-TYPE
	LldpremoteDeviceEntry

lldpremoteDeviceIndex		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.1
The index of LLDP remote device
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

lldpremoteDeviceLocalPort		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.2
LLDP remote device local port
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceChassisIDsubtype		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.3
LLDP remote device chassis ID subtype
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceChassisID		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.4
LLDP remote device chassis ID
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDevicePortIDsubtype		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.5
LLDP remote device port ID subtype
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDevicePortID		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.6
LLDP remote device port ID
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceSystemName		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.7
LLDP remote device system name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceTimetolive		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.8
LLDP remote device time to live
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceEntryIndex		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.9
LLDP remote device entry index
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDevicePortDescription		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.10
LDP remote device port description
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceSystemdescription		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.11
LLDP remote device system description
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceSupportedsystemcapabilities		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.12
LLDP remote device supported syste, capabilities
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceEnablesystemcapabilities		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.13
LLDP remote device enable system capabilities
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceManagementAddress		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.14
LLDP remote device management address
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceAuto-negosupported		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.15
LLDP remote device auto-nego supported
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceAuto-negoenabled		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.16
LLDP remote device auto-nego enabled
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceAuto-negoAdvertisedCapabilities		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.17
LLDP remote device auto-nego advertised capabilities
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceOperationMAUtype		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.18
LLDP remote device operation MAU type
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceMdipowersupportportclass		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.19
LLDP remote device PSE MDI power support class
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDevicePsemdipowersupport		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.20
LLDP remote device PSE MDI power support
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDevicePsemdipowerstatus		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.21
LLDP remote device PSE MDI power status
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDevicePsepowerpaircontrolability		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.22
LLDP remote device PSE power pair control ability
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDevicePsepowerpair		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.23
LLDP remote device PSE power pair
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDevicePsepowerclass		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.24
LLDP remote device PSE power class
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceIeee8023MaxFrameSize		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.25
LLDP remote device IEEE 802.3 Max frame size
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceAggregationCapability		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.26
LLDP remote device aggregation capabilities
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceAggregationStatus		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.27
LLDP remote device aggregation status
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceAggregationPortID		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.28
LLDP remote device aggregation Port ID
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDevicePvid		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.29
LLDP remote device PVID
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceVlanName		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.30
LLDP remote device VLAN name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpremoteDeviceRowStatus		1.3.6.1.4.1.10297.202.7000.7.1.9.1.1.31
LLDP remote device device rowstatus
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), desroty(6)

lldpOverloadingTable		1.3.6.1.4.1.10297.202.7000.7.1.10
The table of LLDP overlaoding
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LLDPOverloadingEntry

lldpOverloadingEntry		1.3.6.1.4.1.10297.202.7000.7.1.10.1
The entry of LLDP overlaoding
Status: current	Access: not-accessible
OBJECT-TYPE
	LLDPOverloadingEntry

lldpOverloadingPortIndex		1.3.6.1.4.1.10297.202.7000.7.1.10.1.1
The port index of LLDP overlaoding
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

lldpOverloadingTotal		1.3.6.1.4.1.10297.202.7000.7.1.10.1.2
LLDP overloading total
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

lldpOverloadingLeftToSend		1.3.6.1.4.1.10297.202.7000.7.1.10.1.3
LLDP overloading left to send
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

lldpOverloadingStatus		1.3.6.1.4.1.10297.202.7000.7.1.10.1.4
LLDP overloading status
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpOverloadingMandatoryTLVs		1.3.6.1.4.1.10297.202.7000.7.1.10.1.5
LLDP overloading mandatory TLVs
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpOverloadingIeee8023TLVs		1.3.6.1.4.1.10297.202.7000.7.1.10.1.6
LLDP overloading IEEE 802.3 TLVs
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpOverloadingOptionalTLVs		1.3.6.1.4.1.10297.202.7000.7.1.10.1.7
LLDP overloading optional TLVs
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

lldpOverloadingIeee8021TLVs		1.3.6.1.4.1.10297.202.7000.7.1.10.1.8
LLDP overloading IEEE 802.1 TLVs
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

snmpState		4.1
SNMP golbal setting
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

snmpCommunityTable		4.2
The table of SNMP community
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		CommunityEntry

snmpCommunityEntry		4.2.1
The entry of SNMP community
Status: current	Access: not-accessible
OBJECT-TYPE
	CommunityEntry

snmpCommunityIndex		4.2.1.1
The index of SNMP community
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..8

snmpCommunityString		4.2.1.2
The name of SNMP community
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

snmpCommunityAccessRight		4.2.1.3
SNMP access mode
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ro(1), rw(2)

snmpCommunityRowStatus		4.2.1.99
User can use createAndWait(5) to create new entry. After setup the value, user use active(1) to set into switch. User can use destory to delete(6) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	active(1), notInService(2), createAndWait(5), destory(6)

snmpTrapHostTable		4.3
The table of SNMP trap host
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SnmpTrapHostEntry

snmpTrapHostEntry		4.3.1
The entry of SNMP trap host
Status: current	Access: not-accessible
OBJECT-TYPE
	SnmpTrapHostEntry

snmpTrapHostIndex		4.3.1.1
The index of SNMP trap host
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..8

snmpTrapHostIpaddress		4.3.1.2
The ipaddress or hostname of SNMP trap host
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

snmpTrapHostCommunityName		4.3.1.3
The community name of SNMP trap host
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

snmpTrapHostVersion		4.3.1.4
The SNMP version of SNMP trap host
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	v1(1), v2cTrap(2), v2cInform(3), v3Trap(4), v3Inform(5)

snmpTrapHostRowStatus		4.3.1.99
User can use createAndWait(5) to create new entry. After setup the value, user use active(1) to set into switch. User can use destory to delete(6) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	active(1), notInService(2), createAndWait(5), destory(6)

snmpv3UserTable		4.4
The table of SNMPv3 user
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SNMPv3UserEntry

snmpv3UserEntry		4.4.1
The entry of SNMPv3 user
Status: current	Access: not-accessible
OBJECT-TYPE
	SNMPv3UserEntry

snmpv3UserIndex		4.4.1.1
The index of SNMPv3 user
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..8

snmpv3UserName		4.4.1.2
The name of SNMPv3 user. Please input more than 8 characters.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

snmpv3UserAccessRight		4.4.1.3
The access right of SNMPv3 user
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	readonly(1), readwrite(2)

snmpv3UserAuthProtocol		4.4.1.4
The authentication protocol of SNMPv3 user
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), md5(2), sha(3)

snmpv3UserAuthPassword		4.4.1.5
The authentication password of SNMPv3 user.The password must be at least eight characters long.The password can include alphabetic, numeric, and '-', '_', '.'
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

snmpv3UserPrivProtocol		4.4.1.6
The priviledge protocol of SNMPv3 user
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), des(2), aes(3)

snmpv3UserPrivPassword		4.4.1.7
The priviledge password of SNMPv3 user.The password must be at least eight characters long.The password can include alphabetic, numeric, and '-', '_', '.'
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

snmpv3UserRowStatus		4.4.1.99
User can use createAndWait(5) to create new entry. After setup the value, user use active(1) to set into switch. User can use destory to delete(6) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	active(1), notInService(2), createAndWait(5), destory(6)

snmpv3EngineID		4.5
The snmpv3 engine ID
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

poeSystemSetting		1.3.6.1.4.1.10297.202.7000.7.3.1
OBJECT IDENTIFIER

poeFwVersion		1.3.6.1.4.1.10297.202.7000.7.3.1.1
The PoE firmware version
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

poeMaxPowerAvailable		1.3.6.1.4.1.10297.202.7000.7.3.1.2
The maximum power available in PoE. actual maximun power value is different according Switch Model. ex : EKI-7710G maximun poe power value is 120W. EKI-7712G maximun poe power value is 240W.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..720

poeActualPowerConsumption		1.3.6.1.4.1.10297.202.7000.7.3.1.3
The actual power consumption in PoE
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

poeOverLoadDisconnect		1.3.6.1.4.1.10297.202.7000.7.3.1.4
The overload disconnect mode in PoE
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	overload-port-first(1), port-based-priority(2)

poePortSettingTable		1.3.6.1.4.1.10297.202.7000.7.3.2
The table of PoE port setting
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PoEPortSettingEntry

poePortSettingEntry		1.3.6.1.4.1.10297.202.7000.7.3.2.1
The table of PoE port setting
Status: current	Access: not-accessible
OBJECT-TYPE
	PoEPortSettingEntry

poePortIndex		1.3.6.1.4.1.10297.202.7000.7.3.2.1.1
The index of PoE port setting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

poePortState		1.3.6.1.4.1.10297.202.7000.7.3.2.1.2
The state of PoE port
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

poePortLegacy		1.3.6.1.4.1.10297.202.7000.7.3.2.1.3
The legacy of PoE port
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

poePortPowerLimitClass		1.3.6.1.4.1.10297.202.7000.7.3.2.1.4
The power limit form classification of PoE port
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

poePortPriority		1.3.6.1.4.1.10297.202.7000.7.3.2.1.5
The priority of PoE port
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	low(1), medium(2), high(3), critical(4)

poePortPowerLimit		1.3.6.1.4.1.10297.202.7000.7.3.2.1.6
The power limit of PoE port
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..30000

poePortStatusTable		1.3.6.1.4.1.10297.202.7000.7.3.3
The table of PoE port status
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PoEPortStatusEntry

poePortStatusEntry		1.3.6.1.4.1.10297.202.7000.7.3.3.1
The table of PoE port status
Status: current	Access: not-accessible
OBJECT-TYPE
	PoEPortStatusEntry

poePortStatusIndex		1.3.6.1.4.1.10297.202.7000.7.3.3.1.1
The index of PoE port status
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

poePortCurrent		1.3.6.1.4.1.10297.202.7000.7.3.3.1.2
The current of PoE port
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

poePortVoltage		1.3.6.1.4.1.10297.202.7000.7.3.3.1.3
The voltage of PoE port
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

poePortPower		1.3.6.1.4.1.10297.202.7000.7.3.3.1.4
The power of PoE port
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

poePortTemp		1.3.6.1.4.1.10297.202.7000.7.3.3.1.5
The temperature of PoE port
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

tcpModbusState		1.3.6.1.4.1.10297.202.7000.7.4.1
The state of TCP Modbus
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

tcpModbusTimeout		1.3.6.1.4.1.10297.202.7000.7.4.2
The time out of TCP Modbus
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..32767

dhcpServerState		1.3.6.1.4.1.10297.202.7000.7.5.1
The state of DHCP Server
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

dhcpServerGlobalSetting		1.3.6.1.4.1.10297.202.7000.7.5.2
OBJECT IDENTIFIER

dhcpServerLeaseTime		1.3.6.1.4.1.10297.202.7000.7.5.2.1
The lease time of DHCP server
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	60..864000

dhcpServerLowIP		1.3.6.1.4.1.10297.202.7000.7.5.2.2
The low IP address of DHCP server
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerHighIP		1.3.6.1.4.1.10297.202.7000.7.5.2.3
The high IP address of DHCP server
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerSubmask		1.3.6.1.4.1.10297.202.7000.7.5.2.4
The subnet mask of DHCP server
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerGateway		1.3.6.1.4.1.10297.202.7000.7.5.2.5
The gateway of DHCP server
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerDNS		1.3.6.1.4.1.10297.202.7000.7.5.2.6
The DNS of DHCP server
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerStatus		1.3.6.1.4.1.10297.202.7000.7.5.2.7
If user set golbal setting with SNMP, the value would not apply to swith. They need to set active(1) to apply into switch.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), notInService(2)

dhcpServerClearIpPool		1.3.6.1.4.1.10297.202.7000.7.5.2.8
Clear IP pool in DHCP Server
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	clear(1)

dhcpServerPortTable		1.3.6.1.4.1.10297.202.7000.7.5.3
The table of DHCP server port setting
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DHCPServerPortEntry

dhcpServerPortEntry		1.3.6.1.4.1.10297.202.7000.7.5.3.1
The entry of DHCP server port setting
Status: current	Access: not-accessible
OBJECT-TYPE
	DHCPServerPortEntry

dhcpServerPortIndex		1.3.6.1.4.1.10297.202.7000.7.5.3.1.1
The index of DHCP server port setting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..65535

dhcpServerPortLowIP		1.3.6.1.4.1.10297.202.7000.7.5.3.1.2
The low IP address of DHCP server port
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerPortHighIP		1.3.6.1.4.1.10297.202.7000.7.5.3.1.3
The high IP address of DHCP server port
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerPortMask		1.3.6.1.4.1.10297.202.7000.7.5.3.1.4
The subnet mask of DHCP server port
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerPortGW		1.3.6.1.4.1.10297.202.7000.7.5.3.1.5
The gateway of DHCP server port
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerPortDNS		1.3.6.1.4.1.10297.202.7000.7.5.3.1.6
The DNS of DHCP server port
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerPortStatus		1.3.6.1.4.1.10297.202.7000.7.5.3.1.7
If user set port setting with SNMP, the value would not apply to swith. They need to set active(1) to apply into switch.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), notInService(2)

dhcpServerPortClear		1.3.6.1.4.1.10297.202.7000.7.5.3.1.8
Clear IP poll on DHCP server port
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nothing(0), clear(1)

dhcpServerOpt82Table		1.3.6.1.4.1.10297.202.7000.7.5.4
The table of DHCP option 82 setting
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DHCPServerOpt82Entry

dhcpServerOpt82Entry		1.3.6.1.4.1.10297.202.7000.7.5.4.1
The entry of DHCP option 82 setting
Status: current	Access: not-accessible
OBJECT-TYPE
	DHCPServerOpt82Entry

dhcpServerOpt82Index		1.3.6.1.4.1.10297.202.7000.7.5.4.1.1
The index of DHCP server option 82 setting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2

dhcpServerOpt82CircuitIDFormat		1.3.6.1.4.1.10297.202.7000.7.5.4.1.2
The circuit ID format of DHCP option 82
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	string(1), hex(2)

dhcpServerOpt82CircuitID		1.3.6.1.4.1.10297.202.7000.7.5.4.1.3
The circuit ID of DHCP option 82
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

dhcpServerOpt82RemoteIDFormat		1.3.6.1.4.1.10297.202.7000.7.5.4.1.4
The remote ID format of DHCP option 82
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	string(1), hex(2)

dhcpServerOpt82RemoteID		1.3.6.1.4.1.10297.202.7000.7.5.4.1.5
The remote ID of DHCP option 82
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

dhcpServerOpt82LowIP		1.3.6.1.4.1.10297.202.7000.7.5.4.1.6
The low IP address of DHCP option 82
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerOpt82HighIP		1.3.6.1.4.1.10297.202.7000.7.5.4.1.7
The high IP address of DHCP option 82
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerOpt82Mask		1.3.6.1.4.1.10297.202.7000.7.5.4.1.8
The subnet mask of DHCP option 82
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerOpt82GW		1.3.6.1.4.1.10297.202.7000.7.5.4.1.9
The gateway of DHCP option 82
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerOpt82DNS		1.3.6.1.4.1.10297.202.7000.7.5.4.1.10
The DNS of DHCP option 82
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerOpt82Status		1.3.6.1.4.1.10297.202.7000.7.5.4.1.11
If user set option82 setting with SNMP, the value would not apply to swith. They need to set active(1) to apply into switch.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), notInService(2)

dhcpServerOpt82Clear		1.3.6.1.4.1.10297.202.7000.7.5.4.1.12
Clear IP poll on DHCP option 82
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nothing(0), clear(1)

dhcpServerLeaseTable		1.3.6.1.4.1.10297.202.7000.7.5.5
The table of DHCP server lease entry
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DHCPServerLeaseEntry

dhcpServerLeaseEntry		1.3.6.1.4.1.10297.202.7000.7.5.5.1
The entry of DHCP server lease entry
Status: current	Access: not-accessible
OBJECT-TYPE
	DHCPServerLeaseEntry

dhcpServerLeaseIndex		1.3.6.1.4.1.10297.202.7000.7.5.5.1.1
The index of DHCP server lease entry
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..1000

dhcpServerLeaseIp		1.3.6.1.4.1.10297.202.7000.7.5.5.1.2
The IP address of DHCP server lease entry
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

dhcpServerLeaseClientMac		1.3.6.1.4.1.10297.202.7000.7.5.5.1.3
The client MAC of DHCP server lease entry
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

dhcpServerLeaseStartTime		1.3.6.1.4.1.10297.202.7000.7.5.5.1.4
The start time of DHCP server lease entry
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

dhcpServerLeaseEndTime		1.3.6.1.4.1.10297.202.7000.7.5.5.1.5
The end time of DHCP server lease entry
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

dhcpServerLeaseType		1.3.6.1.4.1.10297.202.7000.7.5.5.1.6
The type of DHCP server lease entry
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

dhcpServerRestart		1.3.6.1.4.1.10297.202.7000.7.5.6
Restart DHCP Server
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	restart(1)

dhcpServerVlanTable		1.3.6.1.4.1.10297.202.7000.7.5.7
The table of DHCP VLAN setting
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DHCPServerVlanEntry

dhcpServerVlanEntry		1.3.6.1.4.1.10297.202.7000.7.5.7.1
The entry of DHCP VLAN setting
Status: current	Access: not-accessible
OBJECT-TYPE
	DHCPServerVlanEntry

dhcpServerVlanIndex		1.3.6.1.4.1.10297.202.7000.7.5.7.1.1
The index of DHCP server VLAN setting
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2

dhcpServerVlanId		1.3.6.1.4.1.10297.202.7000.7.5.7.1.2
The VLAN ID of DHCP VLAN setting
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..4094

dhcpServerVlanLowIP		1.3.6.1.4.1.10297.202.7000.7.5.7.1.3
The low IP address of DHCP VLAN
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerVlanHighIP		1.3.6.1.4.1.10297.202.7000.7.5.7.1.4
The high IP address of DHCP VLAN
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerVlanMask		1.3.6.1.4.1.10297.202.7000.7.5.7.1.5
The subnet mask of DHCP VLAN
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerVlanGW		1.3.6.1.4.1.10297.202.7000.7.5.7.1.6
The gateway of DHCP VLAN
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerVlanDNS		1.3.6.1.4.1.10297.202.7000.7.5.7.1.7
The DNS of DHCP VLAN
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerVlanStatus		1.3.6.1.4.1.10297.202.7000.7.5.7.1.8
If user set VLAN setting with SNMP, the value would not apply to swith. They need to set active(1) to apply into switch.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), notInService(2)

dhcpServerVlanClear		1.3.6.1.4.1.10297.202.7000.7.5.7.1.9
Clear IP poll on DHCP VLAN
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	nothing(0), clear(1)

dhcpServerClientMacTable		1.3.6.1.4.1.10297.202.7000.7.5.8
The table of DHCP client mac setting
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		DhcpServerClientMacEntry

dhcpServerClientMacEntry		1.3.6.1.4.1.10297.202.7000.7.5.8.1
The entry of DHCP server client mac setting
Status: current	Access: not-accessible
OBJECT-TYPE
	DhcpServerClientMacEntry

dhcpServerClientMacEntryID		1.3.6.1.4.1.10297.202.7000.7.5.8.1.1
The index of DHCP server client mac entry
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..100

dhcpServerClientMacEntryMac		1.3.6.1.4.1.10297.202.7000.7.5.8.1.2
The MAC address of DHCP server client mac entry.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

dhcpServerClientMacEntryIP		1.3.6.1.4.1.10297.202.7000.7.5.8.1.3
The IP address of DHCP server client mac entry.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerClientMacEntryMask		1.3.6.1.4.1.10297.202.7000.7.5.8.1.4
The subnet mask of DHCP DHCP server client mac entry.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerClientMacEntryGW		1.3.6.1.4.1.10297.202.7000.7.5.8.1.5
The gateway of DHCP DHCP server client mac entry.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerClientMacEntryDNS		1.3.6.1.4.1.10297.202.7000.7.5.8.1.6
The DNS of DHCP DHCP server client mac entry.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dhcpServerClientMacEntryRowStatus		1.3.6.1.4.1.10297.202.7000.7.5.8.1.7
User can use createRequest(2) to create new entry. After setup the value, user use valid(1) to set into switch. User can use destory to invalid(4) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	valid(1), createRequest(2), underCreation(3), invalid(4)

smtpActiveProfile		1.3.6.1.4.1.10297.202.7000.7.6.1
The active profile of SMTP client
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	one(1), two(2), none(3)

smtpProfileTable		1.3.6.1.4.1.10297.202.7000.7.6.2
The table of SMTP client profile
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SMTPProfileEntry

smtpProfileEntry		1.3.6.1.4.1.10297.202.7000.7.6.2.1
The entry of SMTP client profile
Status: current	Access: not-accessible
OBJECT-TYPE
	SMTPProfileEntry

smtpProfileIndex		1.3.6.1.4.1.10297.202.7000.7.6.2.1.1
The index of SMTP client profile
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..2

smtpServerIp		1.3.6.1.4.1.10297.202.7000.7.6.2.1.2
The SMTP server IP
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

smtpServerPort		1.3.6.1.4.1.10297.202.7000.7.6.2.1.3
The SMTP server port
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

smtpSenderMail		1.3.6.1.4.1.10297.202.7000.7.6.2.1.4
The SMTP sender mail
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

smtpTargetMail1		1.3.6.1.4.1.10297.202.7000.7.6.2.1.5
The SMTP target mail 1
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

smtpTargetMail2		1.3.6.1.4.1.10297.202.7000.7.6.2.1.6
The SMTP target mail 2
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

smtpTargetMail3		1.3.6.1.4.1.10297.202.7000.7.6.2.1.7
The SMTP target mail 3
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

smtpTargetMail4		1.3.6.1.4.1.10297.202.7000.7.6.2.1.8
The SMTP target mail 4
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

smtpTargetMail5		1.3.6.1.4.1.10297.202.7000.7.6.2.1.9
The SMTP target mail 5
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

smtpTargetMail6		1.3.6.1.4.1.10297.202.7000.7.6.2.1.10
The SMTP target mail 6
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

smtpTargetMail7		1.3.6.1.4.1.10297.202.7000.7.6.2.1.11
The SMTP target mail 7
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

smtpTargetMail8		1.3.6.1.4.1.10297.202.7000.7.6.2.1.12
The SMTP target mail 8
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rmonStatisticsTable		1.3.6.1.4.1.10297.202.7000.7.7.1
The table of RMON Statistics
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RMONStatisticsEntry

rmonStatisticsEntry		1.3.6.1.4.1.10297.202.7000.7.7.1.1
The entry of RMON Statistics
Status: current	Access: not-accessible
OBJECT-TYPE
	RMONStatisticsEntry

rmonStatisticsIndex		1.3.6.1.4.1.10297.202.7000.7.7.1.1.1
The index of RMON Statistics
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

rmonStatisticsPort		1.3.6.1.4.1.10297.202.7000.7.7.1.1.2
The port number of RMON Statistics
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rmonStatisticsDropEvents		1.3.6.1.4.1.10297.202.7000.7.7.1.1.3
The drop events of RMON Statistics
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rmonStatisticsOctets		1.3.6.1.4.1.10297.202.7000.7.7.1.1.4
The octets of RMON Statistics
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rmonStatisticsPackets		1.3.6.1.4.1.10297.202.7000.7.7.1.1.5
The packets of RMON Statistics
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rmonStatisticsBroadcast		1.3.6.1.4.1.10297.202.7000.7.7.1.1.6
The broadcast of RMON Statistics
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rmonStatisticsMulticast		1.3.6.1.4.1.10297.202.7000.7.7.1.1.7
The multicast of RMON Statistics
Status: current	Access: read-only
OBJECT-TYPE
	Counter32

rmonStatisticsOwner		1.3.6.1.4.1.10297.202.7000.7.7.1.1.8
The owner of RMON Statistics
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rmonStatisticsRowStatus		1.3.6.1.4.1.10297.202.7000.7.7.1.1.9
User can use createRequest(2) to create new entry. After setup the value, user use valid(1) to set into switch. User can use destory to invalid(4) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	valid(1), createRequest(2), underCreation(3), invalid(4)

rmonHistoryTable		1.3.6.1.4.1.10297.202.7000.7.7.2
The table of RMON history
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RMONHistoryEntry

rmonHistoryEntry		1.3.6.1.4.1.10297.202.7000.7.7.2.1
The entry of RMON history
Status: current	Access: not-accessible
OBJECT-TYPE
	RMONHistoryEntry

rmonHistoryIndex		1.3.6.1.4.1.10297.202.7000.7.7.2.1.1
The index of RMON history
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

rmonHistoryPort		1.3.6.1.4.1.10297.202.7000.7.7.2.1.2
The port number of RMON history
Status: current	Access: read-write
OBJECT-TYPE
	Integer32

rmonHistoryBucketsRequest		1.3.6.1.4.1.10297.202.7000.7.7.2.1.3
The buckets requested of RMON history
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..50

rmonHistoryInterval		1.3.6.1.4.1.10297.202.7000.7.7.2.1.5
The index of RMON history
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..3600

rmonHistoryOwner		1.3.6.1.4.1.10297.202.7000.7.7.2.1.6
The port number of RMON history
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rmonHistoryRowStatus		1.3.6.1.4.1.10297.202.7000.7.7.2.1.7
User can use createRequest(2) to create new entry. After setup the value, user use valid(1) to set into switch. User can use destory to invalid(4) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	valid(1), createRequest(2), underCreation(3), invalid(4)

rmonAlarmTable		1.3.6.1.4.1.10297.202.7000.7.7.3
The table of RMON alarm
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RMONAlarmEntry

rmonAlarmEntry		1.3.6.1.4.1.10297.202.7000.7.7.3.1
The entry of RMON alarm
Status: current	Access: not-accessible
OBJECT-TYPE
	RMONAlarmEntry

rmonAlarmIndex		1.3.6.1.4.1.10297.202.7000.7.7.3.1.1
The index of RMON alarm
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

rmonAlarmInterval		1.3.6.1.4.1.10297.202.7000.7.7.3.1.2
The interval of RMON alarm
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..2147483647

rmonAlarmVariable		1.3.6.1.4.1.10297.202.7000.7.7.3.1.3
The variable of RMON alarm
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rmonAlarmSampleType		1.3.6.1.4.1.10297.202.7000.7.7.3.1.4
The sample type of RMON alarm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	absolute(1), delta(2)

rmonAlarmRisingThreshold		1.3.6.1.4.1.10297.202.7000.7.7.3.1.5
The rising threshold of RMON alarm
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..2147483647

rmonAlarmFallingThreshold		1.3.6.1.4.1.10297.202.7000.7.7.3.1.6
The falling threshold of RMON alarm
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..2147483647

rmonAlarmRisingEventIndex		1.3.6.1.4.1.10297.202.7000.7.7.3.1.7
The rising event index of RMON alarm
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

rmonAlarmFallingEventIndex		1.3.6.1.4.1.10297.202.7000.7.7.3.1.8
The falling event indx of RMON alarm
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

rmonAlarmOwner		1.3.6.1.4.1.10297.202.7000.7.7.3.1.9
The owner of RMON alarm
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rmonAlarmRowStatus		1.3.6.1.4.1.10297.202.7000.7.7.3.1.10
User can use createRequest(2) to create new entry. After setup the value, user use valid(1) to set into switch. User can use destory to invalid(4) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	valid(1), createRequest(2), underCreation(3), invalid(4)

rmonEventTable		1.3.6.1.4.1.10297.202.7000.7.7.4
The table of RMON event
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RMONEventEntry

rmonEventEntry		1.3.6.1.4.1.10297.202.7000.7.7.4.1
The entry of RMON event
Status: current	Access: not-accessible
OBJECT-TYPE
	RMONEventEntry

rmonEventIndex		1.3.6.1.4.1.10297.202.7000.7.7.4.1.1
The index of RMON event
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

rmonEventDescription		1.3.6.1.4.1.10297.202.7000.7.7.4.1.2
The description of RMON event
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rmonEventType		1.3.6.1.4.1.10297.202.7000.7.7.4.1.3
The type of RMON event
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	none(1), log(2), trap(3), logTrap(4)

rmonEventCommunity		1.3.6.1.4.1.10297.202.7000.7.7.4.1.4
The community of RMON event
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rmonEventOwner		1.3.6.1.4.1.10297.202.7000.7.7.4.1.5
The owner of RMON event
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

rmonEventRowStatus		1.3.6.1.4.1.10297.202.7000.7.7.4.1.7
User can use createRequest(2) to create new entry. After setup the value, user use valid(1) to set into switch. User can use destory to invalid(4) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	valid(1), createRequest(2), underCreation(3), invalid(4)

ntpServer		1.3.6.1.4.1.10297.202.7000.7.8.1
enable/disable NTP server.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ntpManualTime		1.3.6.1.4.1.10297.202.7000.7.8.2
enable/disable NTP manual time.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ntpServerTable		1.3.6.1.4.1.10297.202.7000.7.8.3
The table of NTP server
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		NtpServerEntry

ntpServerEntry		1.3.6.1.4.1.10297.202.7000.7.8.3.1
The entry of NTP server
Status: current	Access: not-accessible
OBJECT-TYPE
	NtpServerEntry

ntpServerIndex		1.3.6.1.4.1.10297.202.7000.7.8.3.1.1
The index of NTP server
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..10

ntpServerIp		1.3.6.1.4.1.10297.202.7000.7.8.3.1.2
The ip address of NTP server
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

copperTest		1.3.6.1.4.1.10297.202.7000.8.1
OBJECT IDENTIFIER

pingTest		1.3.6.1.4.1.10297.202.7000.8.2
OBJECT IDENTIFIER

ipv6pingTest		1.3.6.1.4.1.10297.202.7000.8.3
OBJECT IDENTIFIER

loggingSetting		1.3.6.1.4.1.10297.202.7000.8.4
OBJECT IDENTIFIER

factoryDefault		1.3.6.1.4.1.10297.202.7000.8.5
OBJECT IDENTIFIER

reboot		1.3.6.1.4.1.10297.202.7000.8.6
OBJECT IDENTIFIER

dhcpAutoProvision		1.3.6.1.4.1.10297.202.7000.8.7
OBJECT IDENTIFIER

ledIndication		1.3.6.1.4.1.10297.202.7000.8.8
OBJECT IDENTIFIER

portNumber		1.3.6.1.4.1.10297.202.7000.8.1.1
The port ID for copper test
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

copperTestAction		1.3.6.1.4.1.10297.202.7000.8.1.2
Copper test action
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	copperTest(1)

copperTestResult		1.3.6.1.4.1.10297.202.7000.8.1.3
OBJECT IDENTIFIER

resultPort		1.3.6.1.4.1.10297.202.7000.8.1.3.1
The copper test port ID
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER

channelA		1.3.6.1.4.1.10297.202.7000.8.1.3.2
The copper test result for channel A
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

cableLengthA		1.3.6.1.4.1.10297.202.7000.8.1.3.3
The copper test result for cable length A
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

channelB		1.3.6.1.4.1.10297.202.7000.8.1.3.4
The copper test result for channel B
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

cableLengthB		1.3.6.1.4.1.10297.202.7000.8.1.3.5
The copper test result forcable length B
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

channelC		1.3.6.1.4.1.10297.202.7000.8.1.3.6
The copper test result for channel C
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

cableLengthC		1.3.6.1.4.1.10297.202.7000.8.1.3.7
The copper test result for cable length C
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

channelD		1.3.6.1.4.1.10297.202.7000.8.1.3.8
The copper test result for channel D
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

cableLengthD		1.3.6.1.4.1.10297.202.7000.8.1.3.9
The copper test result for cable length D
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

channelRx		1.3.6.1.4.1.10297.202.7000.8.1.3.10
The copper test result for channel Rx
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

cableLengthRx		1.3.6.1.4.1.10297.202.7000.8.1.3.11
The copper test result for cable length Rx
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

channelTx		1.3.6.1.4.1.10297.202.7000.8.1.3.12
The copper test result for channel Tx
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

cableLengthTx		1.3.6.1.4.1.10297.202.7000.8.1.3.13
The copper test result for cable length Tx
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

pingIPAddress		1.3.6.1.4.1.10297.202.7000.8.2.1
The IP address or hostname of ping target
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

pingCount		1.3.6.1.4.1.10297.202.7000.8.2.2
How many times to send ping request packets
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..5

pingInterval		1.3.6.1.4.1.10297.202.7000.8.2.3
Time interval between each ping request packets
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..5

pingSize		1.3.6.1.4.1.10297.202.7000.8.2.4
The size of ping packet
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	8..5120

pingAction		1.3.6.1.4.1.10297.202.7000.8.2.5
The ping action
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ping(1)

pingResult		1.3.6.1.4.1.10297.202.7000.8.2.6
After ping finished, results will show in this OID
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

pingIPv6Address		1.3.6.1.4.1.10297.202.7000.8.3.1
The IPv6 address of ping target
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

pingIPv6Count		1.3.6.1.4.1.10297.202.7000.8.3.2
How many times to send ping request packet
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..5

pingIPv6Interval		1.3.6.1.4.1.10297.202.7000.8.3.3
Time interval between each ping request packet
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..5

pingIPv6Size		1.3.6.1.4.1.10297.202.7000.8.3.4
The size of ping packet
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	8..5120

pingIPv6Action		1.3.6.1.4.1.10297.202.7000.8.3.5
The IPv6 ping action
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	ping(1)

pingIPv6Result		1.3.6.1.4.1.10297.202.7000.8.3.6
After ping finished, results will show in this field
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

loggingService		1.3.6.1.4.1.10297.202.7000.8.4.1
Enable/Disable logging system
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

localLoggingTable		1.3.6.1.4.1.10297.202.7000.8.4.2
The table of local logging
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LocalLoggingEntry

localLoggingEntry		1.3.6.1.4.1.10297.202.7000.8.4.2.1
The entry of local logging
Status: current	Access: not-accessible
OBJECT-TYPE
	LocalLoggingEntry

localLoggingIndex		1.3.6.1.4.1.10297.202.7000.8.4.2.1.1
The index of local logging
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..3

bufferedtarget		1.3.6.1.4.1.10297.202.7000.8.4.2.1.2
The target to store log message Buffered: Store log messages in device buffer. File: Store log message in file. Console: Show the log message on console.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	buffered(1), console(2), file(3)

localLoggingStatus		1.3.6.1.4.1.10297.202.7000.8.4.2.1.3
Enable/Disable status the logging system
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

localLoggingSeverity		1.3.6.1.4.1.10297.202.7000.8.4.2.1.4
Severity of log message which will be stored
Status: current	Access: read-write
OBJECT-TYPE
	BITS	emerg(0), alert(1), crit(2), error(3), warning(4), notice(5), info(6), debug(7)

remoteloggingTable		1.3.6.1.4.1.10297.202.7000.8.4.3
The table of remote logging
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		RemoteloggingEntry

remoteloggingEntry		1.3.6.1.4.1.10297.202.7000.8.4.3.1
The entry of remote logging
Status: current	Access: not-accessible
OBJECT-TYPE
	RemoteloggingEntry

remoteloggingIndex		1.3.6.1.4.1.10297.202.7000.8.4.3.1.1
The index of remote logging
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..8

remoteloggingAddress		1.3.6.1.4.1.10297.202.7000.8.4.3.1.2
The IP address of remote log server
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

remoteloggingPort		1.3.6.1.4.1.10297.202.7000.8.4.3.1.3
The port number of remote log server
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..65535

remoteloggingSeverity		1.3.6.1.4.1.10297.202.7000.8.4.3.1.4
The severity of log messages which will be sent
Status: current	Access: read-write
OBJECT-TYPE
	BITS	emerg(0), alert(1), crit(2), error(3), warning(4), notice(5), info(6), debug(7)

remoteloggingFacility		1.3.6.1.4.1.10297.202.7000.8.4.3.1.5
The facility of log messages which will be sent
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	local0(1), local1(2), local2(3), local3(4), local4(5), local5(6), local6(7), local7(8)

remoteloggingRowStatus		1.3.6.1.4.1.10297.202.7000.8.4.3.1.99
User can use createAndWait(5) to create new entry. After setup the value, user use active(1) to set into switch. User can use destory to delete(6) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	active(1), notInService(2), createAndWait(5), destory(6)

factoryDefaultAction		1.3.6.1.4.1.10297.202.7000.8.5.1
user to restore switch to factory default
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	factoryDefault(1)

factoryDefaultKeepFlag		1.3.6.1.4.1.10297.202.7000.8.5.2
Keep setting when switch is restore to factory default.
Status: current	Access: read-write
OBJECT-TYPE
	BITS	vlan(1), ipaddress(2), useraccount(3)

rebootAction		1.3.6.1.4.1.10297.202.7000.8.6.1
user to reboot the switch
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	reboot(1)

dhcpAutoProvisionEnable		1.3.6.1.4.1.10297.202.7000.8.7.1
The status of DHCP auto provision
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ledAlarmState		1.3.6.1.4.1.10297.202.7000.8.8.1
Enable/Disable LED alarm
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ledPowerFailureEvent		1.3.6.1.4.1.10297.202.7000.8.8.2
Enable/Disable LED power failure event
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ledFiberLinkdownEvent		1.3.6.1.4.1.10297.202.7000.8.8.3
Enable/Disable LED fiber port Link down event
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ledPortLinkdownEvent		1.3.6.1.4.1.10297.202.7000.8.8.4
Enable/Disable LED port Link down event
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

ledPortLinkdownEventPort		1.3.6.1.4.1.10297.202.7000.8.8.5
The member ports of LED port Link down event
Status: current	Access: read-write
OBJECT-TYPE
	BITS	port1(0), port2(1), port3(2), port4(3), port5(4), port6(5), port7(6), port8(7), port9(8), port10(9), port11(10), port12(11), port13(12), port14(13), port15(14), port16(15), port17(16), port18(17), port19(18), port20(19), port21(20), port22(21), port23(22), port24(23), port25(24), port26(25), port27(26), port28(27), port29(28), port30(29), port31(30), port32(31)

ledEventInfoTable		1.3.6.1.4.1.10297.202.7000.8.8.6
The table of led event info
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LedEventInfoEntry

ledEventInfoEntry		1.3.6.1.4.1.10297.202.7000.8.8.6.1
The entry of led event info
Status: current	Access: not-accessible
OBJECT-TYPE
	LedEventInfoEntry

ledEventIndex		1.3.6.1.4.1.10297.202.7000.8.8.6.1.1
The index of led event info
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..3

ledType		1.3.6.1.4.1.10297.202.7000.8.8.6.1.2
The type of led event info
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

ledEvent		1.3.6.1.4.1.10297.202.7000.8.8.6.1.3
The event of led event info
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

ledState		1.3.6.1.4.1.10297.202.7000.8.8.6.1.4
The state of led event info
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

ledErrorTimes		1.3.6.1.4.1.10297.202.7000.8.8.6.1.5
The error times of led event info
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..65535

backupManager		1.3.6.1.4.1.10297.202.7000.9.1
OBJECT IDENTIFIER

upgradeManager		1.3.6.1.4.1.10297.202.7000.9.2
OBJECT IDENTIFIER

dualImage		1.3.6.1.4.1.10297.202.7000.9.3
OBJECT IDENTIFIER

configurationManager		1.3.6.1.4.1.10297.202.7000.9.4
OBJECT IDENTIFIER

accountManager		1.3.6.1.4.1.10297.202.7000.9.5
OBJECT IDENTIFIER

nKey		1.3.6.1.4.1.10297.202.7000.9.6
OBJECT IDENTIFIER

backupMethod		1.3.6.1.4.1.10297.202.7000.9.1.1
The method of backup file
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tftp(1)

backupServerIP		1.3.6.1.4.1.10297.202.7000.9.1.2
The IP address of the TFTP server
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

backupType		1.3.6.1.4.1.10297.202.7000.9.1.3
The backup configuration type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	image(1), startupConfig(2), runningConfig(3), flashlog(5), bufferlog(6)

backupImage		1.3.6.1.4.1.10297.202.7000.9.1.4
The backup firmware image
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	partition0(1), partition1(2)

backupAction		1.3.6.1.4.1.10297.202.7000.9.1.5
The backup action
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	backup(1)

upgradeMethod		1.3.6.1.4.1.10297.202.7000.9.2.1
The upgrade file method
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	tftp(1)

upgradeServerIP		1.3.6.1.4.1.10297.202.7000.9.2.2
The server IP address
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

upgradeFileName		1.3.6.1.4.1.10297.202.7000.9.2.3
The upgrade file name
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

upgradeType		1.3.6.1.4.1.10297.202.7000.9.2.4
The upgrade type
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	image(1), startupConfig(2), runningConfig(3)

upgradeImage		1.3.6.1.4.1.10297.202.7000.9.2.5
The uprade firmware image
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	active(1), backup(2)

upgradeAction		1.3.6.1.4.1.10297.202.7000.9.2.6
The upgrade action
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	upgrade(1)

upgradeStatus		1.3.6.1.4.1.10297.202.7000.9.2.7
The upgrade status
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	on-going(1), done(2)

activeImage		1.3.6.1.4.1.10297.202.7000.9.3.1
The active image
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	image1(1), image2(2)

imageInfoTable		1.3.6.1.4.1.10297.202.7000.9.3.2
The table of image info
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ImageInfoEntry

imageInfoEntry		1.3.6.1.4.1.10297.202.7000.9.3.2.1
The entry of image info
Status: current	Access: not-accessible
OBJECT-TYPE
	ImageInfoEntry

flashPartition		1.3.6.1.4.1.10297.202.7000.9.3.2.1.1
The FLASH partition
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..2

imageName		1.3.6.1.4.1.10297.202.7000.9.3.2.1.2
The image name
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

imageSize		1.3.6.1.4.1.10297.202.7000.9.3.2.1.3
The image size
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

createdTime		1.3.6.1.4.1.10297.202.7000.9.3.2.1.4
The FW creation time
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

imageVersion		1.3.6.1.4.1.10297.202.7000.9.3.2.1.5
The image version
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

sourceFile		1.3.6.1.4.1.10297.202.7000.9.4.1
The configuration source file
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	running(1), startup(2)

destinationFile		1.3.6.1.4.1.10297.202.7000.9.4.2
The configuration destination file
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	running(1), startup(2)

saveConfiguration		1.3.6.1.4.1.10297.202.7000.9.4.3
Save the current configuration
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	save(1)

localUserTable		1.3.6.1.4.1.10297.202.7000.9.5.1
The table of local user
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		LocalUserEntry

localUserEntry		1.3.6.1.4.1.10297.202.7000.9.5.1.1
The entry of local user
Status: current	Access: not-accessible
OBJECT-TYPE
	LocalUserEntry

localUserIndex		1.3.6.1.4.1.10297.202.7000.9.5.1.1.1
The index of local user
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	1..32

localUserName		1.3.6.1.4.1.10297.202.7000.9.5.1.1.2
The user name of local user
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

localUserPasswordType		1.3.6.1.4.1.10297.202.7000.9.5.1.1.3
The pasword type of local user
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	cleartext(1), encrypted(2), noPassword(3)

localUserPassword		1.3.6.1.4.1.10297.202.7000.9.5.1.1.4
The password of local user
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

localUserPrivilegeType		1.3.6.1.4.1.10297.202.7000.9.5.1.1.5
The privilege type of local user
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	admin(1), user(2)

localUserRowStatus		1.3.6.1.4.1.10297.202.7000.9.5.1.1.99
User can use createAndWait(5) to create new entry. After setup the value, user use active(1) to set into switch. User can use destory to delete(6) an entry.
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	active(1), notInService(2), createAndWait(5), destory(6)

nKeyAutoMode		1.3.6.1.4.1.10297.202.7000.9.6.1
The auto mode of N-Key.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

nKeyStatus		1.3.6.1.4.1.10297.202.7000.9.6.2
Select N-key is idle or backup the current configurations to N-Key or restore N-Key's configurations to switch. The fourth option is read-only.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	idle(0), backup(1), restore(2), running(3)

trapObject		1.3.6.1.4.1.10297.202.7000.99.1
OBJECT IDENTIFIER

ddmiAlarmDescr		1.3.6.1.4.1.10297.202.7000.99.1.1
The description of DDMI trap
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

xRingMasterStatus		1.3.6.1.4.1.10297.202.7000.99.1.2
The status of XRing Pro Master.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	masterToSlave(1), slaveToMaster(2)

ddmiAlarmWarning		1.3.6.1.4.1.10297.202.7000.99.2
The DDMI trap
Status: current	Access: read-only
NOTIFICATION-TYPE

xRingProMasterChange		1.3.6.1.4.1.10297.202.7000.99.3
This trap is sent if XRing Pro master change
Status: current	Access: read-only
NOTIFICATION-TYPE

stpStateChange		1.3.6.1.4.1.10297.202.7000.99.5
This trap is sent if spanning tree port state change to blocking or forwarding
Status: current	Access: read-only
NOTIFICATION-TYPE