AC-MEDIA-MIB

File: AC-MEDIA-MIB.mib (107033 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC RFC1155-SMI
SNMP-FRAMEWORK-MIB AUDIOCODES-TYPES-MIB

Imported symbols

OBJECT-TYPE MODULE-IDENTITY TAddress
DisplayString DateAndTime TEXTUAL-CONVENTION
IpAddress Unsigned32 Integer32
enterprises RowStatus SnmpAdminString
audioCodes acRegistrations acGeneric
acProducts acBoardMibs

Defined Types

AcMediaDspEntry  
SEQUENCE    
  acMediaDspIndex Unsigned32
  acMediaDspRowStatus RowStatus
  acMediaDspTemplateNumber Unsigned32
  acMediaDspResourcesPercentage Unsigned32

AcAMRFECCodecPoliciesEntry  
SEQUENCE    
  acAMRFECCodecPoliciesIndex Unsigned32
  acAMRFECCodecPoliciesRowStatus RowStatus
  acAMRFECCodecPoliciesRate Unsigned32
  acAMRFECCodecPoliciesRedundancyLevel Unsigned32
  acAMRFECCodecPoliciesThreshold Unsigned32
  acAMRFECCodecPoliciesHysteresis Unsigned32

AcIPLegsEntry  
SEQUENCE    
  acIPLegsLegIndex Unsigned32
  acIPLegsCallIndex Unsigned32
  acIPLegsRTPActive INTEGER
  acIPLegsCoderType INTEGER
  acIPLegsSilenceCompression INTEGER
  acIPLegsDTMFDetection INTEGER
  acIPLegsLocalRTPPort Unsigned32
  acIPLegsRemoteRTPAddress IpAddress
  acIPLegsFaxTransportType INTEGER
  acIPLegsRxPackets Unsigned32
  acIPLegsTxPackets Unsigned32
  acIPLegsRxBytes Unsigned32
  acIPLegsTxBytes Unsigned32
  acIPLegsJitter Unsigned32
  acIPLegsPacketLoss Unsigned32
  acIPLegsSSRCOfSender Unsigned32
  acIPLegsDSPDevice Unsigned32
  acIPLegsLegName SnmpAdminString

AcIPMediaChannelsResourcesEntry  
SEQUENCE    
  acIPMediaChannelsResourcesIndex Unsigned32
  acIPMediaChannelsResourcesRowStatus RowStatus
  acIPMediaChannelsResourcesAction INTEGER
  acIPMediaChannelsResourcesActionRes INTEGER
  acIPMediaChannelsResourcesModuleID Unsigned32
  acIPMediaChannelsResourcesDSPChannelsReserved Unsigned32

Defined Values

acMedia 1.3.6.1.4.1.5003.9.10.4
Tok_String
MODULE-IDENTITY    

acMediaConfiguration 1.3.6.1.4.1.5003.9.10.4.1
OBJECT IDENTIFIER    

acMediaDSPConfig 1.3.6.1.4.1.5003.9.10.4.1.1
OBJECT IDENTIFIER    

acMediaDSPConfigVersionTemplateNumber 1.3.6.1.4.1.5003.9.10.4.1.1.1
Selects the DSP load number. Each load has a different coder list, a different channel capacity and different features supported. Range = 0 to 255. Access: Offline. AC INI-Param: DSPVERSIONTEMPLATENUMBER
OBJECT-TYPE    
  Unsigned32 0..255  

acMediaDspTable 1.3.6.1.4.1.5003.9.10.4.1.1.21
Tok_String
OBJECT-TYPE    
  SEQUENCE OF  
    AcMediaDspEntry

acMediaDspEntry 1.3.6.1.4.1.5003.9.10.4.1.1.21.1
Tok_String
OBJECT-TYPE    
  AcMediaDspEntry  

acMediaDspIndex 1.3.6.1.4.1.5003.9.10.4.1.1.21.1.1
Entry number in the table. AC INI-Param: DspTemplates_Index
OBJECT-TYPE    
  Unsigned32 0..1  

acMediaDspRowStatus 1.3.6.1.4.1.5003.9.10.4.1.1.21.1.2
ROWSTATUS field for line. Internal parameter. AC INI-Param: N/A
OBJECT-TYPE    
  RowStatus  

acMediaDspTemplateNumber 1.3.6.1.4.1.5003.9.10.4.1.1.21.1.3
DSP template number. Access: Offline. AC INI-Param: DspTemplates_DspTemplateNumber
OBJECT-TYPE    
  Unsigned32 0..8  

acMediaDspResourcesPercentage 1.3.6.1.4.1.5003.9.10.4.1.1.21.1.4
Percentage use for the specified template. Access: Offline. AC INI-Param: DspTemplates_DspResourcesPercentage
OBJECT-TYPE    
  Unsigned32 0..100  

acMediaVoiceConfig 1.3.6.1.4.1.5003.9.10.4.1.2
OBJECT IDENTIFIER    

acVoice 1.3.6.1.4.1.5003.9.10.4.1.2.1
OBJECT IDENTIFIER    

acVoicePayloadFormat 1.3.6.1.4.1.5003.9.10.4.1.2.1.1
Sets the voice payload format. Choose either 0 = RTP or 1 = ATM (which enables working with vendors that use G.726 ATM Payload Format over RTP. Uses the enum acTVoicePayloadFormat. 0 = VoicePayloadFormatRTP 1 = VoicePayloadFormatATM 2 = VoicePAyloadFormatIllegal. Access: Online. AC INI-Param: VOICEPAYLOADFORMAT
OBJECT-TYPE    
  INTEGER voicePayloadFormatRTP(0), voicePayloadFormatATM(1)  

acVoiceVolume 1.3.6.1.4.1.5003.9.10.4.1.2.1.2
Defines the voice output gain control. Range: -32 dB to +31 dB in 1 dB steps -32 = mute Default = 0 = No Gain. Access: Online. AC INI-Param: VOICEVOLUME
OBJECT-TYPE    
  Integer32 -32..31  

acVoiceInputGain 1.3.6.1.4.1.5003.9.10.4.1.2.1.3
Defines the PCM input gain. Range = -32 dB to +31 dB in 1 dB steps. Default = No Gain. Access: Online. AC INI-Param: INPUTGAIN
OBJECT-TYPE    
  Integer32 -32..31  

acVoiceTestMode 1.3.6.1.4.1.5003.9.10.4.1.2.1.4
Defines the type of testing mode applied: 0 = Coder Loopback performs an encoder/decoder loopback inside the DSP device 1 = PCM Loopback loops back an incoming PCM to the outgoing PCM. 2 = ToneInjection generates a 1000 Hz tone to the outgoing PCM 3 = NoLoopback sets the channel to work in normal mode. Access: Online. AC INI-Param: TESTMODE
OBJECT-TYPE    
  INTEGER coderLoopback(0), pCMLoopback(1), toneInjection(2), noLoopback(3)  

acVoiceTTYTransportType 1.3.6.1.4.1.5003.9.10.4.1.2.1.5
Defines the transferring method of TTY signals during a call 0 = Disable 1= Bypass 2 = Relay . Access: Online. AC INI-Param: TTYTRANSPORTTYPE
OBJECT-TYPE    
  INTEGER disable(0), inband-Relay(2), bypass(1)  

acVoiceEnableMediaSecurity 1.3.6.1.4.1.5003.9.10.4.1.2.1.6
Enables or disables Media Security protocol (SRTP) . Enabling this parameter might reduce the board channel capacity. 0 = Disable 1 = Enable. Access: Offline. AC INI-Param: ENABLEMEDIASECURITY
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acVoiceCoderRate 1.3.6.1.4.1.5003.9.10.4.1.2.1.20
OBJECT IDENTIFIER    

acVoiceCoderRateEVRC 1.3.6.1.4.1.5003.9.10.4.1.2.1.20.1
This parameter is used to configure the EVRC coder bit rate. 0 = Variable Rate 1 = 1 kbps 2 = 4 kbps 3 = 8 kbps. Access: Online. AC INI-Param: EVRCRate
OBJECT-TYPE    
  INTEGER variableRate(0), ac1kbps(1), ac4kbps(2), ac8kbps(3)  

acVoiceCoderRateQCELP8 1.3.6.1.4.1.5003.9.10.4.1.2.1.20.2
This parameter is used to configure the QCELP8 coder bit rate. 0 = Variable Rate 1 = 1 kbps 2 = 2 kbps 3 = 4 kbps 4 = 8 kbps. Access: Online. AC INI-Param: QCELP8Rate
OBJECT-TYPE    
  INTEGER variableRate(0), ac1kbps(1), ac2kbps(2), ac4kbps(3), ac8kbps(4)  

acVoiceCoderRateQCELP13 1.3.6.1.4.1.5003.9.10.4.1.2.1.20.3
This parameter is used to configure the QCELP13 coder bit rate. 0 = Variable Rate 1 = 1 kbps 2 = 3 kbps 3 = 7 kbps 4 = 13 kbps . Access: Online. AC INI-Param: QCELP13Rate
OBJECT-TYPE    
  INTEGER variableRate(0), ac1kbps(1), ac3kbps(2), ac7kbps(3), ac13kbps(4)  

acVoiceCoderRateG729EVMaxBitRate 1.3.6.1.4.1.5003.9.10.4.1.2.1.20.4
Determines the maximum generation bitrate for all participants in a session using G729EV coder. This parameter is defined per session and is equal for all the parties. The initial generation bit rate is the minimum between the MaxBitRate and the MBS values. Possible values are: 0 = G729EV_RATE_8_KBPS 1 = G729EV_RATE_12_KBPS 2 = G729EV_RATE_14_KBPS 3 = G729EV_RATE_16_KBPS 4 = G729EV_RATE_18_KBPS 5 = G729EV_RATE_20_KBPS 6 = G729EV_RATE_22_KBPS 7 = G729EV_RATE_24_KBPS 8 = G729EV_RATE_26_KBPS 9 = G729EV_RATE_28_KBPS 10 = G729EV_RATE_30_KBPS 11 = G729EV_RATE_32_KBPS 15 = G729EV_RATE_UNDEFINED. Access: Online. AC INI-Param: G729EVMaxBitRate
OBJECT-TYPE    
  INTEGER g729EV-RATE-8-KBPS(0), g729EV-RATE-12-KBPS(1), g729EV-RATE-14-KBPS(2), g729EV-RATE-16-KBPS(3), g729EV-RATE-18-KBPS(4), g729EV-RATE-20-KBPS(5), g729EV-RATE-22-KBPS(6), g729EV-RATE-24-KBPS(7), g729EV-RATE-26-KBPS(8), g729EV-RATE-28-KBPS(9), g729EV-RATE-30-KBPS(10), g729EV-RATE-32-KBPS(11), g729EV-RATE-UNDEFINED(15)  

acVoiceCoderRateG729EVLocalMBS 1.3.6.1.4.1.5003.9.10.4.1.2.1.20.5
Determines the maximal bitrate, which may be used by the G729EV coder at a specific channel. This parameter is defined per channel and may vary between the parties. The initial generation bit rate is the minimum between the MaxBitRate and the MBS values. Possible values are: 0 = G729EV_RATE_8_KBPS 1 = G729EV_RATE_12_KBPS 2 = G729EV_RATE_14_KBPS 3 = G729EV_RATE_16_KBPS 4 = G729EV_RATE_18_KBPS 5 = G729EV_RATE_20_KBPS 6 = G729EV_RATE_22_KBPS 7 = G729EV_RATE_24_KBPS 8 = G729EV_RATE_26_KBPS 9 = G729EV_RATE_28_KBPS 10 = G729EV_RATE_30_KBPS 11 = G729EV_RATE_32_KBPS 15 = G729EV_RATE_UNDEFINED. Access: Online. AC INI-Param: G729EVLocalMBS
OBJECT-TYPE    
  INTEGER g729EV-RATE-8-KBPS(0), g729EV-RATE-12-KBPS(1), g729EV-RATE-14-KBPS(2), g729EV-RATE-16-KBPS(3), g729EV-RATE-18-KBPS(4), g729EV-RATE-20-KBPS(5), g729EV-RATE-22-KBPS(6), g729EV-RATE-24-KBPS(7), g729EV-RATE-26-KBPS(8), g729EV-RATE-28-KBPS(9), g729EV-RATE-30-KBPS(10), g729EV-RATE-32-KBPS(11), g729EV-RATE-UNDEFINED(15)  

acVoiceCoderRateG729EVReceiveMBS 1.3.6.1.4.1.5003.9.10.4.1.2.1.20.6
Determines the value of the MBS field of the G729EV frames to be sent to the other party. This parameter reflects the maximum bit rate, which the local G729EV supports as a receiver. Possible values are: 0 = G729EV_RATE_8_KBPS 1 = G729EV_RATE_12_KBPS 2 = G729EV_RATE_14_KBPS 3 = G729EV_RATE_16_KBPS 4 = G729EV_RATE_18_KBPS 5 = G729EV_RATE_20_KBPS 6 = G729EV_RATE_22_KBPS 7 = G729EV_RATE_24_KBPS 8 = G729EV_RATE_26_KBPS 9 = G729EV_RATE_28_KBPS 10 = G729EV_RATE_30_KBPS 11 = G729EV_RATE_32_KBPS 15 = G729EV_RATE_UNDEFINED. Access: Online. AC INI-Param: G729EVReceiveMBS
OBJECT-TYPE    
  INTEGER g729EV-RATE-8-KBPS(0), g729EV-RATE-12-KBPS(1), g729EV-RATE-14-KBPS(2), g729EV-RATE-16-KBPS(3), g729EV-RATE-18-KBPS(4), g729EV-RATE-20-KBPS(5), g729EV-RATE-22-KBPS(6), g729EV-RATE-24-KBPS(7), g729EV-RATE-26-KBPS(8), g729EV-RATE-28-KBPS(9), g729EV-RATE-30-KBPS(10), g729EV-RATE-32-KBPS(11), g729EV-RATE-UNDEFINED(15)  

acVoiceCoderRateMsRtaForwardErrorCorrectionEnable 1.3.6.1.4.1.5003.9.10.4.1.2.1.20.7
Determines the Microsoft RTA coder forward error correction mode. 0 - Disable. 1 - Enable. Access: Online. AC INI-Param: MSRTAForwardErrorCorrectionEnable
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acVoiceCoderRateMsRtaTxBitRate 1.3.6.1.4.1.5003.9.10.4.1.2.1.20.8
Determines the Microsoft RTA coder TX bit rate. 0 - Automatic. Any value between 8,800 - 29,000. Access: Online. AC INI-Param: MSRTATxBitRate
OBJECT-TYPE    
  Unsigned32 0..29000  

acVoiceAGC 1.3.6.1.4.1.5003.9.10.4.1.2.2
OBJECT IDENTIFIER    

acVoiceAGCEnable 1.3.6.1.4.1.5003.9.10.4.1.2.2.1
Activates the AGC (Automatic Gain Control). 0 = Disable 1 = Enable. Access: Online. AC INI-Param: ENABLEAGC
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acVoiceAGCGainSlope 1.3.6.1.4.1.5003.9.10.4.1.2.2.2
Determines the AGC (Automatic Gain Control) convergence rate. Range = 0 to 31 (according to acTAGCGainSlope) Default = 3 (= 1 db/sec). Access: Online. AC INI-Param: AGCGAINSLOPE
OBJECT-TYPE    
  Unsigned32 0..31  

acVoiceAGCRedirection 1.3.6.1.4.1.5003.9.10.4.1.2.2.3
Determines the AGC (Automatic Gain Control) direction. 0 = AGC works on signals from the TDM side 1 = AGC works on signals coming from the Network side. Access: Online. AC INI-Param: AGCREDIRECTION
OBJECT-TYPE    
  Unsigned32 0..1  

acVoiceAGCTargetEnergy 1.3.6.1.4.1.5003.9.10.4.1.2.2.4
Determines the signal energy value [-dBm] that the AGC (Automatic Gain Control) attempts to attain. Range = 0 to 63. Access: Online. AC INI-Param: AGCTARGETENERGY
OBJECT-TYPE    
  Unsigned32 0..63  

acVoiceAGCMinGain 1.3.6.1.4.1.5003.9.10.4.1.2.2.5
Defines the minimum gain by the AGC when activated [- db]. Range = 0 to -31. Access: Offline. AC INI-Param: AGCMINGAIN
OBJECT-TYPE    
  Unsigned32 0..31  

acVoiceAGCMaxGain 1.3.6.1.4.1.5003.9.10.4.1.2.2.6
Defines the maximum gain by the AGC when activated [db]. Range = 0 to 18. Access: Offline. AC INI-Param: AGCMAXGAIN
OBJECT-TYPE    
  Unsigned32 0..18  

acVoiceAGCDisableFastAdaptation 1.3.6.1.4.1.5003.9.10.4.1.2.2.7
Disables the AGC Fast Adaptation mode. Enable = 1 Disable = 0. Access: Offline. AC INI-Param: AGCDISABLEFASTADAPTATION
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acVoiceEC 1.3.6.1.4.1.5003.9.10.4.1.2.3
OBJECT IDENTIFIER    

acVoiceECEnable 1.3.6.1.4.1.5003.9.10.4.1.2.3.1
Enables or disables the Echo Canceller. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: ENABLEECHOCANCELLER
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acVoiceECMaxLength 1.3.6.1.4.1.5003.9.10.4.1.2.3.2
Defines the maximum board EC (Echo Canceler) length capability. 0 = EC length determined internally to reach maximum channel capacity. 4 = 32 msec 11 = 64 msec 22 = 128 msec TP-1610 only: Using 64 or 128 msec reduces the channel capacity to 200 channels. . Access: Offline. AC INI-Param: MAXECHOCANCELLERLENGTH
OBJECT-TYPE    
  INTEGER eCLengthDefault(0), eCLength15MSec(1), eCLength20MSec(2), eCLength25MSec(3), eCLength32MSec(4), eCLength35MSec(5), eCLength40MSec(6), eCLength45MSec(7), eCLength50MSec(8), eCLength55MSec(9), eCLength60MSec(10), eCLength64MSec(11), eCLength128MSec(22)  

acVoiceECHybridLoss 1.3.6.1.4.1.5003.9.10.4.1.2.3.3
Sets the worst case ratio between the signal level transmitted to the hybrid and the echo level returning from hybrid. Set this per worst hybrid in the system in terms of echo return loss. Refer to the enumeration acTECHybridLoss. 0 = 6 dBm 1 = 9 dBm 2 = 0 dBm 3 = 3 dBm. Access: Online. AC INI-Param: ECHYBRIDLOSS
OBJECT-TYPE    
  INTEGER eCHybridLoss6DBM(0), eCHybridLoss9DBM(1), eCHybridLoss0DBM(2), eCHybridLoss3DBM(3)  

acVoiceECToneDetector 1.3.6.1.4.1.5003.9.10.4.1.2.3.4
Used to configure the Echo Canceler Tone Detector. Detects a 2100 Hz tone at the input signal to the TDM (received signal). Improves Echo Canceler operation accordingly. Detects 2100, 2100 with phase reversals and 2100 with AM. Improves the operation of the Echo Canceler by slowing adaptation when the signal is detected. This data is also used by the fax state machine. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: ECEnableToneDetector
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acVoiceECComfortNoiseGeneration 1.3.6.1.4.1.5003.9.10.4.1.2.3.5
Use this parameter to enable or enable Echo Canceler Comfort Noise Generation, which generates comfort noise when the Non Linear Processor (NLP) is active. When the NLP ascertains that the signal is echo and not doubletalk and decides to clip, instead of transmitting silence it transmits a synthesized signal similar to the background noise. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: ECEnableComfortNoiseGeneration
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acVoiceSC 1.3.6.1.4.1.5003.9.10.4.1.2.4
OBJECT IDENTIFIER    

acVoiceSCMode 1.3.6.1.4.1.5003.9.10.4.1.2.4.1
Enables or disables Silence Suppression Mode. 0 = Disable = SILENCE_COMPRESION_DISABLE 1 = Enable = SILENCE_COMPRESION_ENABLE 2 = Enable without adaptation = SILENCE_COMPRESION_ENABLE_NOISE_ADAPTATION_DISABLE. Access: Online. AC INI-Param: ENABLESILENCECOMPRESSION
OBJECT-TYPE    
  INTEGER sILENCE-COMPRESION-DISABLE(0), sILENCE-COMPRESION-ENABLE(1), sILENCE-COMPRESION-ENABLE-NOISE-ADAPTATION-DISABLE(2)  

acVoiceSCVBRCoderDTXMin 1.3.6.1.4.1.5003.9.10.4.1.2.4.2
Defines the minimum number of frames gap between two SID frames, when using the EVRC voice activity detector. . Access: Online. AC INI-Param: EVRCDTXMin
OBJECT-TYPE    
  Unsigned32 0..20000  

acVoiceSCVBRCoderDTXMax 1.3.6.1.4.1.5003.9.10.4.1.2.4.3
Defines the maximum number of frames gap between two SID frames, when using the EVRC voice activity detector. Access: Online. AC INI-Param: EVRCDTXMax
OBJECT-TYPE    
  Unsigned32 0..20000  

acVoiceSCVBRCoderHangover 1.3.6.1.4.1.5003.9.10.4.1.2.4.4
For indicating the desired number of silence frames at the beginning of each silence period, when using the VBR CODER silence suppression. . Access: Online. AC INI-Param: VBRCoderHangover
OBJECT-TYPE    
  Unsigned32 0..255  

acMediaFaxModemConfig 1.3.6.1.4.1.5003.9.10.4.1.3
OBJECT IDENTIFIER    

acFaxModem 1.3.6.1.4.1.5003.9.10.4.1.3.1
OBJECT IDENTIFIER    

acFMCommon 1.3.6.1.4.1.5003.9.10.4.1.3.1.1
OBJECT IDENTIFIER    

acFMCommonRelayVolume 1.3.6.1.4.1.5003.9.10.4.1.3.1.1.1
Determines the fax gain control. The range -18 to -3 relates to -18.5 dBm to -3.5 dBm in steps of 1 dBm. Access: Online. AC INI-Param: FAXMODEMRELAYVOLUME
OBJECT-TYPE    
  Integer32 -18..-3  

acFMCommonV34Transport 1.3.6.1.4.1.5003.9.10.4.1.3.1.1.2
Sets the V.34 modem transport method. 0 = Transparent 2 = Bypass 3 = Transparent with Events 4 = AnsMute. Access: Online. AC INI-Param: V34MODEMTRANSPORTTYPE
OBJECT-TYPE    
  INTEGER disable(0), relayEnable(1), byPassEnable(2), eventsOnly(3), ansMute(4)  

acFMCommonEnableInbandNetworkDetection 1.3.6.1.4.1.5003.9.10.4.1.3.1.1.3
Enables or disables inband network detection related to fax/modem. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: EnableFaxModemInbandNetworkDetection
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acFMBypass 1.3.6.1.4.1.5003.9.10.4.1.3.1.2
OBJECT IDENTIFIER    

acFMBypassCoderType 1.3.6.1.4.1.5003.9.10.4.1.3.1.2.1
Users can use this parameter to set the fax/modem bypass coder (according to acTCoders). 0 = G.711 A-Law 1 = G.711 Mu-Law. Access: Online. AC INI-Param: FAXMODEMBYPASSCODERTYPE
OBJECT-TYPE    
  INTEGER g711Alaw-64(0), g711Mulaw(1)  

acFMBypassPacketizationPeriod 1.3.6.1.4.1.5003.9.10.4.1.3.1.2.2
Defines the number of basic frames to generate one RTP fax/modem bypass packet. Access: Online. AC INI-Param: FAXMODEMBYPASSM
OBJECT-TYPE    
  Unsigned32 1..12  

acFMBypassBasicPacketInterval 1.3.6.1.4.1.5003.9.10.4.1.3.1.2.3
Sets the basic Fax / Modem Bypass RTP packet rate. 0 = Default (set internally) (PACKET_INTERVAL_DEFAULT) 1 = 5 msec (PACKET_INTERVAL_5_MSEC) 2 = 10 msec (PACKET_INTERVAL_10_MSEC) 3 = 20 msec (PACKET_INTERVAL_20_MSEC). Access: Online. AC INI-Param: FAXMODEMBYPASSBASICRTPPACKETINTERVAL
OBJECT-TYPE    
  INTEGER pACKET-INTERVAL-DEFAULT(0), pACKET-INTERVAL-5-MSEC(1), pACKET-INTERVAL-10-MSEC(2), pACKET-INTERVAL-20-MSEC(3)  

acFMBypassDJBufMinDelay 1.3.6.1.4.1.5003.9.10.4.1.3.1.2.4
Determines the Jitter Buffer constant delay (in milliseconds) during a Fax & Modem Bypass session. (The minimum Jitter Buffer Size). Range = 0 to 150. Access: Online. AC INI-Param: FAXMODEMBYPASDJBUFMINDELAY
OBJECT-TYPE    
  Unsigned32 0..150  

acFMBypassFaxBypassOutputGain 1.3.6.1.4.1.5003.9.10.4.1.3.1.2.5
Defines the fax bypass output gain control. Range: -31 dB to +31 dB in 1 dB steps Default = 0 = No Gain. Access: Online. AC INI-Param: FaxBypassOutputGain
OBJECT-TYPE    
  Integer32 -31..31  

acFMBypassModemBypassOutputGain 1.3.6.1.4.1.5003.9.10.4.1.3.1.2.6
Defines the modem bypass output gain control. Range: -31 dB to +31 dB in 1 dB steps Default = 0 = No Gain. Access: Online. AC INI-Param: ModemBypassOutputGain
OBJECT-TYPE    
  Integer32 -31..31  

acFMNSE 1.3.6.1.4.1.5003.9.10.4.1.3.1.3
OBJECT IDENTIFIER    

acFMNSEPayloadType 1.3.6.1.4.1.5003.9.10.4.1.3.1.3.1
Users can use this parameter to modify the NSE packet's payload type. Range = 96 to 127. Access: Online. AC INI-Param: NSEPAYLOADTYPE
OBJECT-TYPE    
  Unsigned32 96..127  

acFMNSEMode 1.3.6.1.4.1.5003.9.10.4.1.3.1.3.2
Enables or disables Cisco's NSE fax / modem automatic pass-through mode. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: NSEMODE
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acFax 1.3.6.1.4.1.5003.9.10.4.1.3.2
OBJECT IDENTIFIER    

acFaxTransportMode 1.3.6.1.4.1.5003.9.10.4.1.3.2.1
Sets the Fax over IP transport method. 0 = Transparent 1 = Relay 2 = Bypass 3 = Transparent with Events. Access: Online. AC INI-Param: FAXTRANSPORTMODE
OBJECT-TYPE    
  INTEGER disable(0), relayEnable(1), byPassEnable(2), eventsOnly(3)  

acFaxBypassPayloadType 1.3.6.1.4.1.5003.9.10.4.1.3.2.2
Users can use this parameter to modify the Fax Bypass Mode RTP packet's payload type. In the case of congestion (if the selected payload type is already used for other coders/modes), then a TP_SETUP_PARAMETER_INVALID_ERROR is issued and the payload type is set to the default value (102). It is the user's responsibility to avoid congestion with other payload types. Range = 0 to 127. Access: Online. AC INI-Param: FAXBYPASSPAYLOADTYPE
OBJECT-TYPE    
  Unsigned32 0..127  

acFaxRelayECMEnable 1.3.6.1.4.1.5003.9.10.4.1.3.2.3
Enables or disables the using of ECM mode during Fax Relay. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: FAXRELAYECMENABLE
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acFaxRelayMaxRate 1.3.6.1.4.1.5003.9.10.4.1.3.2.4
Limits the maximum rate at which fax messages are transmitted. 0 = 2400 bps 1 = 4800 bps 2 = 7200 bps 3 = 9600 bps 4 = 12000 bps 5 = 14400 bps 6 = 16800 bps 7 =19200 bps 8 = 21600 bps 9 = 24000 bps 10 = 26400 bps 11 = 28800 bps 12 = 31200 bps 13 = 33600bps. Access: Online. AC INI-Param: FAXRELAYMAXRATE
OBJECT-TYPE    
  INTEGER acRate2400bps(0), acRate4800bps(1), acRate7200bps(2), acRate9600bps(3), acRate12000bps(4), acRate14400bps(5), acRate16800bps(6), acRate19200b(7), acRate21600bps(8), acRate24000bps(9), acRate26400bps(10), acRate28800bps(11), acRate31200bps(12), acRate33600bps(13)  

acFaxRelayRedundancyDepth 1.3.6.1.4.1.5003.9.10.4.1.3.2.5
Determines the depth of redundancy for fax packets. This parameter is applicable only to non-V.21 packets. 0 = No redundancy 1 = 1 packet redundancy 2 = 2 packet redundancy. Access: Online. AC INI-Param: FAXRELAYREDUNDANCYDEPTH
OBJECT-TYPE    
  Unsigned32 0..2  

acFaxEnhancedRelayRedundancyDepth 1.3.6.1.4.1.5003.9.10.4.1.3.2.6
Determines the number of repetitions to be applied to control packets when using the T.38 standard. 0 = No redundancy 1 = 1 packet redundancy 2 = 2 packet redundancy 3 = 3 packet redundancy 4 = Maximum redundancy. Access: Online. AC INI-Param: FAXRELAYENHANCEDREDUNDANCYDEPTH
OBJECT-TYPE    
  Unsigned32 0..4  

acFaxCNGDetectorMode 1.3.6.1.4.1.5003.9.10.4.1.3.2.7
Determines the CNG Detector mode. 0 = Disable 1 = Relay 2 = Event Only. Access: Online. AC INI-Param: CNGDETECTORMODE
OBJECT-TYPE    
  INTEGER cNG-DETECTOR-MODE-DISABLE(0), cNG-DETECTOR-MODE-RELAY(1), cNG-DETECTOR-MODE-EVENT-ONLY(2)  

acFaxV34TransportMethod 1.3.6.1.4.1.5003.9.10.4.1.3.2.8
Determines the V.34 fax transport method. One of the following values: 0 = Transparent 1 = Relay 2 = Bypass 3 = Transparent with Events. Access: Online. AC INI-Param: V34FAXTRANSPORTTYPE
OBJECT-TYPE    
  INTEGER disable(0), relayEnable(1), byPassEnable(2), eventsOnly(3)  

acFaxT38Version 1.3.6.1.4.1.5003.9.10.4.1.3.2.9
T38 fax relay version. 0 = T.38 version 0 (from 06/1998) 3 = T.38 version 3 (V.34 over T.38 support) Default = 3. Access: Online. AC INI-Param: T38Version
OBJECT-TYPE    
  INTEGER t38Version0(0), t38Version3(3)  

acModem 1.3.6.1.4.1.5003.9.10.4.1.3.3
OBJECT IDENTIFIER    

acModemV22Transport 1.3.6.1.4.1.5003.9.10.4.1.3.3.1
Sets the V.22 modem transport method. 0 = Transparent 2 = Bypass 3 = Transparent with Events. Access: Online. AC INI-Param: V22MODEMTRANSPORTTYPE
OBJECT-TYPE    
  INTEGER disable(0), relayEnable(1), byPassEnable(2), eventsOnly(3)  

acModemV23Transport 1.3.6.1.4.1.5003.9.10.4.1.3.3.2
Sets the V.23 modem transport method. 0 = Transparent 2 = Bypass 3 = Transparent with Events. Access: Online. AC INI-Param: V23MODEMTRANSPORTTYPE
OBJECT-TYPE    
  INTEGER disable(0), relayEnable(1), byPassEnable(2), eventsOnly(3)  

acModemV32Transport 1.3.6.1.4.1.5003.9.10.4.1.3.3.3
Sets the V.32 modem transport method. 0 = Transparent 2 = Bypass 3 = Transparent with Events 4 = AnsMute. Access: Online. AC INI-Param: V32MODEMTRANSPORTTYPE
OBJECT-TYPE    
  INTEGER disable(0), relayEnable(1), byPassEnable(2), eventsOnly(3), ansMute(4)  

acModemBypassPayloadType 1.3.6.1.4.1.5003.9.10.4.1.3.3.4
Users can use this parameter to modify the Modem Bypass Mode RTP packet's payload type. In the case of congestion (if the selected payload type is already used for other coders/modes), then a TP_SETUP_PARAMETER_INVALID_ERROR is issued and the payload type is set to the default value (103). It is the user's responsibility to avoid congestion with other payload types. Range = 0 to 127. Access: Online. AC INI-Param: MODEMBYPASSPAYLOADTYPE
OBJECT-TYPE    
  Unsigned32 0..127  

acModemBellTransportType 1.3.6.1.4.1.5003.9.10.4.1.3.3.5
Use this parameter to set the Bell modem transport method. 0 = Transparent 2 = Bypass (enum ByPassEnable) 3 = Transparent with Events (enum EventsOnly). Access: Online. AC INI-Param: BellModemTransportType
OBJECT-TYPE    
  INTEGER disable(0), byPassEnable(2), eventsOnly(3)  

acModemV21Transport 1.3.6.1.4.1.5003.9.10.4.1.3.3.6
Sets the V.21 modem transport method (must be set to 0 = Disable). 0 = Transparent 2 = Bypass 3 = Transparent with Events. Access: Online. AC INI-Param: V21ModemTransportType
OBJECT-TYPE    
  INTEGER disable(0), relayEnable(1), byPassEnable(2), eventsOnly(3)  

acModemEnableV150ModemRelaySupport 1.3.6.1.4.1.5003.9.10.4.1.3.3.7
Determines whether to enable V.150.1 modem relay support. Range: 0 - Disable 1 - Enable. Access: Offline. AC INI-Param: EnableV150ModemRelaySupport
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acV150dot1 1.3.6.1.4.1.5003.9.10.4.1.3.4
OBJECT IDENTIFIER    

acV150dot1AllocationProfile 1.3.6.1.4.1.5003.9.10.4.1.3.4.1
Selects the V.150.1 profile, determining how many DSP channels have V.150.1 support. Range = 0 to 3. Access: Offline. AC INI-Param: V1501AllocationProfile
OBJECT-TYPE    
  Unsigned32 0..21  

acV150dot1SSEPayloadTypeRx 1.3.6.1.4.1.5003.9.10.4.1.3.4.2
SSE payload type RX. Access: Online. AC INI-Param: V1501SSEPayloadTypeRx
OBJECT-TYPE    
  Unsigned32 96..127  

acV150dot1SSEPayloadTypeTx 1.3.6.1.4.1.5003.9.10.4.1.3.4.3
SSE payload type TX. Access: Online. AC INI-Param: V1501SSEPayloadTypeTx
OBJECT-TYPE    
  Unsigned32 96..127  

acV150dot1SSERedundancyDepth 1.3.6.1.4.1.5003.9.10.4.1.3.4.4
SSE is a part of V150.1 modem relay protocol and SSE messages are sent over RTP. SSE redundancy refers to the sending of SSE messages several times to increase reliability. This parameter determines the number of times each SSE message is to be resent. Access: Online. AC INI-Param: V1501SSERedundancyDepth
OBJECT-TYPE    
  Unsigned32 1..6  

acV150dot1SPRTPayloadTypeRx 1.3.6.1.4.1.5003.9.10.4.1.3.4.5
SPRT payload type RX. Access: Online. AC INI-Param: V1501SPRTPayloadTypeRx
OBJECT-TYPE    
  Unsigned32 96..127  

acV150dot1SPRTPayloadTypeTx 1.3.6.1.4.1.5003.9.10.4.1.3.4.6
SPRT payload type TX. Access: Online. AC INI-Param: V1501SPRTPayloadTypeTx
OBJECT-TYPE    
  Unsigned32 96..127  

acV150dot1SPRTTransportChannel0MaxPayloadSize 1.3.6.1.4.1.5003.9.10.4.1.3.4.7
SPRT transport channel 0 max payload size. Access: Online. AC INI-Param: V1501SPRTTransportChannel0MaxPayloadSize
OBJECT-TYPE    
  Unsigned32 140..256  

acV150dot1SPRTTransportChannel2MaxPayloadSize 1.3.6.1.4.1.5003.9.10.4.1.3.4.8
SPRT transport channel 2 max payload size. Access: Online. AC INI-Param: V1501SPRTTransportChannel2MaxPayloadSize
OBJECT-TYPE    
  Unsigned32 132..256  

acV150dot1SPRTTransportChannel2MaxWindowSize 1.3.6.1.4.1.5003.9.10.4.1.3.4.9
SPRT transport channel 2 max window size. Access: Online. AC INI-Param: V1501SPRTTransportChannel2MaxWindowSize
OBJECT-TYPE    
  Unsigned32 8..32  

acV150dot1SPRTTransportChannel3MaxPayloadSize 1.3.6.1.4.1.5003.9.10.4.1.3.4.10
SPRT transport channel 3 max payload size. Access: Online. AC INI-Param: V1501SPRTTransportChannel3MaxPayloadSize
OBJECT-TYPE    
  Unsigned32 140..256  

acMediaRtpRtcpConfig 1.3.6.1.4.1.5003.9.10.4.1.4
OBJECT IDENTIFIER    

acRtpRtcp 1.3.6.1.4.1.5003.9.10.4.1.4.1
OBJECT IDENTIFIER    

acRtpRtcpBrokenConnectionEventTimeout 1.3.6.1.4.1.5003.9.10.4.1.4.1.1
Determines for how long the RTP connection should be broken before the Broken Connection event is issued. In units of 100 msec. . Access: Online. AC INI-Param: BROKENCONNECTIONEVENTTIMEOUT
OBJECT-TYPE    
  Unsigned32 3..2684354  

acRtpRtcpBrokenConnectionEventActivationMode 1.3.6.1.4.1.5003.9.10.4.1.4.1.2
Determines if the broken connection mechanism is activated when the RTP stream is activated or when the first RTP packet is received. 0 = After First incoming packet (default) 1 = Upon channel?s RTP activation. . Access: Online. AC INI-Param: BROKENCONNECTIONEVENTACTIVATIONMODE
OBJECT-TYPE    
  INTEGER afterFirstIncomingRTPPacket(0), onRTPStreamActivation(1)  

acRtpRtcpBasicRTPPacketInterval 1.3.6.1.4.1.5003.9.10.4.1.4.1.3
Selects the RTP packet rate for sample based coders (such as G.711, G.726, G.727). Also applicable for G.729, G.729E & G.728. 0 = Default (set internally) 1 = 5 msec 2 = 10 msec 3 = 20 msec. Access: Online. AC INI-Param: BASICRTPPACKETINTERVAL
OBJECT-TYPE    
  INTEGER pACKET-INTERVAL-DEFAULT(0), pACKET-INTERVAL-5-MSEC(1), pACKET-INTERVAL-10-MSEC(2), pACKET-INTERVAL-20-MSEC(3)  

acRtpRtcpConnectionEstablishNotificationMode 1.3.6.1.4.1.5003.9.10.4.1.4.1.4
Determines the notification mode for the RTP connection establishment event acEV_CONNECTION_ESTABLISHED. 0 = Notify only after a broken connection event 1 = Also notify when the first RTP packet is received. Access: Online. AC INI-Param: CONNECTIONESTABLISHEMENTNOTIFICATIONMODE
OBJECT-TYPE    
  INTEGER afterBrokenConnection(0), uponFirstRTPFrameDetection(1)  

acRtpRtcpEnableMediaUDPChecksum 1.3.6.1.4.1.5003.9.10.4.1.4.1.5
Determines whether to enable the UDP checksum calculation for RTP media TX over IPv4. One of the following possible values: 0 = Disable (No checksum: UDP checksum for IPv4 TX = 0) 1 = Enable (UDP checksum will be in the UDP header upon IPv4 TX) . Access: Offline. AC INI-Param: EnableMediaUDPChecksum
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acRtp 1.3.6.1.4.1.5003.9.10.4.1.4.2
OBJECT IDENTIFIER    

acRtpBaseUDPPort 1.3.6.1.4.1.5003.9.10.4.1.4.2.1
Defines the lower boundary of UDP ports to be used by the board. The upper boundary is calculated on the basis of BoardBaseUDPPort + 10 * (Number of Channels). This parameter value must be a multiple of 10. . Access: Offline. AC INI-Param: BASEUDPPORT
OBJECT-TYPE    
  Unsigned32 1024..65535  

acRtpComfortNoiseEnable 1.3.6.1.4.1.5003.9.10.4.1.4.2.2
When set to 1 (Enable), SID packets are sent with the RTP SID type (RFC 3389). 0 = Disable 1 = Enable Determines whether Silence Indicator (SID) packets that are sent and received are according to RFC 3389. 0 = Disabled (default). 1 = Enabled. Note: Applicable only to MP-11x and Mediant 1000. . Access: Online. AC INI-Param: ENABLESTANDARDSIDPAYLOADTYPE
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acRtpEnableRFC2658Interleaving 1.3.6.1.4.1.5003.9.10.4.1.4.2.3
When enabled, RTP packets include an interleaving byte for VBR coders. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: ENABLERFC2658INTERLEAVING
OBJECT-TYPE    
  INTEGER withOut-RFC2658Interleaving-And-TOC(0), including-RFC2658Interleaving-And-TOC(1), including-TOC-Only(2), interleave-Bundling(3)  

acRtpRxTxMode 1.3.6.1.4.1.5003.9.10.4.1.4.2.4
Selects which RTP directions are enabled. Both Tx and Rx sides can be disabled. 0 = RTPTxRx 1 = RTPTxOnly 2 = RTPRxOnly 3 = RTPUnactive 4 = RTPRxRFC2833Tx. Access: Online. AC INI-Param: RTPDIRECTIONCONTROL
OBJECT-TYPE    
  INTEGER rTPTxRx(0), rTPTxOnly(1), rTPRxOnly(2), rTPUnactive(3), rTPRxRFC2833Tx(4)  

acRtpRFC2833TxPayloadType 1.3.6.1.4.1.5003.9.10.4.1.4.2.5
Controls the RFC 2833 Tx Relay RTP Payload type. Range = 96 to 127. Access: Online. AC INI-Param: RFC2833TXPAYLOADTYPE
OBJECT-TYPE    
  Unsigned32 96..127  

acRtpRFC2833RxPayloadType 1.3.6.1.4.1.5003.9.10.4.1.4.2.6
Controls the RFC 2833 Rx Relay RTP Payload type. Range = 96 to 127. Access: Online. AC INI-Param: RFC2833RXPAYLOADTYPE
OBJECT-TYPE    
  Unsigned32 96..127  

acRtpRedundancyPayloadType 1.3.6.1.4.1.5003.9.10.4.1.4.2.7
This parameter sets the RFC 2198 (RTP Redundancy) packet's parameter 'RTP Payload Type'. Range: 96 to 127. Access: Online. AC INI-Param: RFC2198PAYLOADTYPE
OBJECT-TYPE    
  Unsigned32 96..127  

acRtpRedundancyDepth 1.3.6.1.4.1.5003.9.10.4.1.4.2.8
Redundancy depth of RFC 2198 redundancy packets. 0 = No redundancy 1 = Redundacny depth. Access: Online. AC INI-Param: RTPREDUNDANCYDEPTH
OBJECT-TYPE    
  INTEGER noRedundancy(0), redundacnyDepth(1)  

acRtpPacketizationFactor 1.3.6.1.4.1.5003.9.10.4.1.4.2.9
Defines the number of DSP payloads for generating one RTP packet. Range = Hardware dependent. Access: Online. AC INI-Param: RTPPACKINGFACTOR
OBJECT-TYPE    
  Unsigned32 1..12  

acRtpNoOpPayloadType 1.3.6.1.4.1.5003.9.10.4.1.4.2.10
User can modify the Noop packets RTP Payload type by setting this parameter. Range = 96 to 127. Access: Online. AC INI-Param: RTPNOOPPAYLOADTYPE
OBJECT-TYPE    
  Unsigned32 96..127  

acRtpNoOpEnable 1.3.6.1.4.1.5003.9.10.4.1.4.2.11
Enables / disable Noop packets sending mode. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: RTPNOOPENABLE
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acRtpNoOpInterval 1.3.6.1.4.1.5003.9.10.4.1.4.2.12
Used to modify the Noop packets sending interval Parameter value is in milliseconds Default value = 10 sec (10000 msec) Range = 20 to 600000 (20 msec to 10 min - 10 min = 600000). Access: Online. AC INI-Param: RTPNOOPINTERVAL
OBJECT-TYPE    
  Unsigned32 20..600000  

acRtpVBRCoderHeaderFormat 1.3.6.1.4.1.5003.9.10.4.1.4.2.13
0 - payload only (no header, no toc, no m-factor) 1- support RFC 2658 format, 1 byte for interleaving header (always 0) and toc, no m-factor 2 ? payload including toc only, allow m-factor 3- RFC 3358 format . Access: Online. AC INI-Param: VBRCoderHeaderFormat
OBJECT-TYPE    
  INTEGER withOut-RFC2658Interleaving-And-TOC(0), including-RFC2658Interleaving-And-TOC(1), including-TOC-Only(2), interleave-Bundling(3)  

acRtpAMRCoderHeaderFormat 1.3.6.1.4.1.5003.9.10.4.1.4.2.14
AMR_CODER_HEADER_DEFAULT_FORMAT=0 - old m factor, each frame contains CRM byte and toc RFC_3267_BUNDLING=1 - single CRM byte followed by toc tables RFC_3267_INTERLEAVING=2 - supported as receivers only. Access: Online. AC INI-Param: AMRCODERHEADERFORMAT
OBJECT-TYPE    
  INTEGER cE-AMR-DEFAULT-FORMAT(0), cE-AMR-RFC-3267-BUNDLING(1), cE-AMR-RFC-3267-INTERLEAVING(2), cE-AMR-IF2(3)  

acRtpAMRFECRedundancyDepth 1.3.6.1.4.1.5003.9.10.4.1.4.2.15
Sets the AMR / WB-AMR Redundancy depth according to RFC 3267. 0 = No Redundancy 1 = Redundancy depth of a single packet 2 = Redundancy depth of 2 packets 3 = Redundancy depth of 3 packets . Access: Online. AC INI-Param: AMRFECREDUNDANCYDEPTH
OBJECT-TYPE    
  INTEGER cE-AMR-FEC-REDUNDANCY-LEVEL-NONE(0), cE-AMR-FEC-REDUNDANCY-LEVEL-1(1), cE-AMR-FEC-REDUNDANCY-LEVEL-2(2), cE-AMR-FEC-REDUNDANCY-LEVEL-3(3)  

acRtpAMRFECNumOfMngtPolicyEntries 1.3.6.1.4.1.5003.9.10.4.1.4.2.16
Sets the number of entries to be defined at the AMR management policy table. Each entry defines the policy of a different rate. Access: Online. AC INI-Param: AMRFECNUMBEROFCODECMODES
OBJECT-TYPE    
  Unsigned32 0..9  

acRtpAMRFECDelayHysteresis 1.3.6.1.4.1.5003.9.10.4.1.4.2.17
Defines the hysteresis of the Delay Threshold for AMR Hand-out events (in msec). Access: Online. AC INI-Param: AMRFECDELAYHYSTERESIS
OBJECT-TYPE    
  Unsigned32 0..255  

acRtpAMRFECDelayThreshold 1.3.6.1.4.1.5003.9.10.4.1.4.2.18
Defines the one-way delay value (in msec) that may cause the AMR Hand Out report. 0 = 'Hand Out' report is disabled (default). Access: Online. AC INI-Param: AMRFECDELAYTHRESHHOLD
OBJECT-TYPE    
  Unsigned32 0..255  

acRtpQcelpCoderHeaderFormat 1.3.6.1.4.1.5003.9.10.4.1.4.2.19
Determines whether to define a separate header format for the QCELP coder (different to the header format of EVRC coder). One of the following values: -1 - QCELP coder uses the same header format as EVRC coder, according to VBRCoderHeaderFormat parameter. 1 to 2 - QCELP coder uses the value defined by this parameter to define its header format. This parameter is relevant only for Control Protocol users. TPNCP and PCI users should always use -1 value. Access: Instant. AC INI-Param: QcelpCoderHeaderFormat
OBJECT-TYPE    
  INTEGER parameter-Is-Not-Used(-1), including-RFC2658Interleaving-And-TOC(1), including-TOC-Only(2)  

acAMRFECCodecPolicies 1.3.6.1.4.1.5003.9.10.4.1.4.2.21
OBJECT IDENTIFIER    

acAMRFECCodecPoliciesTable 1.3.6.1.4.1.5003.9.10.4.1.4.2.21.1
Tok_String
OBJECT-TYPE    
  SEQUENCE OF  
    AcAMRFECCodecPoliciesEntry

acAMRFECCodecPoliciesEntry 1.3.6.1.4.1.5003.9.10.4.1.4.2.21.1.1
Tok_String
OBJECT-TYPE    
  AcAMRFECCodecPoliciesEntry  

acAMRFECCodecPoliciesIndex 1.3.6.1.4.1.5003.9.10.4.1.4.2.21.1.1.1
AC INI-Param: AMRFECCodecPolicies_Index
OBJECT-TYPE    
  Unsigned32 0..8  

acAMRFECCodecPoliciesRowStatus 1.3.6.1.4.1.5003.9.10.4.1.4.2.21.1.1.2
AC INI-Param: N/A
OBJECT-TYPE    
  RowStatus  

acAMRFECCodecPoliciesRate 1.3.6.1.4.1.5003.9.10.4.1.4.2.21.1.1.3
AMR Rate x of policy x (values 0-8). Access: Offline. AC INI-Param: AMRFECCodecPolicies_Rate
OBJECT-TYPE    
  Unsigned32  

acAMRFECCodecPoliciesRedundancyLevel 1.3.6.1.4.1.5003.9.10.4.1.4.2.21.1.1.4
Redundancy Level for policy x. Same values as ?RFC 3267 Redundancy? field. Access: Offline. AC INI-Param: AMRFECCodecPolicies_RedundancyLevel
OBJECT-TYPE    
  Unsigned32  

acAMRFECCodecPoliciesThreshold 1.3.6.1.4.1.5003.9.10.4.1.4.2.21.1.1.5
FLR (Frame Loss Ratio) threshold of policy 1. Values are taken from 3GPP TS 44.318 (0-63). Access: Offline. AC INI-Param: AMRFECCodecPolicies_Threshold
OBJECT-TYPE    
  Unsigned32  

acAMRFECCodecPoliciesHysteresis 1.3.6.1.4.1.5003.9.10.4.1.4.2.21.1.1.6
Hysteresis of FLR threshold for policy 1. Values are taken from 3GPP TS 44.318. (0-15). Access: Offline. AC INI-Param: AMRFECCodecPolicies_Hysteresis
OBJECT-TYPE    
  Unsigned32  

acRtcp 1.3.6.1.4.1.5003.9.10.4.1.4.3
OBJECT IDENTIFIER    

acRtcpDisableIntervalRandomization 1.3.6.1.4.1.5003.9.10.4.1.4.3.1
Controls whether RTCP report intervals are randomized or whether each report interval accords exactly to the parameter defining RTCP Mean Tx Interval (in milliseconds). 0 = Randomize 1 = Don?t Randomize. Access: Online. AC INI-Param: DISABLERTCPRANDOMIZE
OBJECT-TYPE    
  Unsigned32 0..128  

acRtcpXr 1.3.6.1.4.1.5003.9.10.4.1.4.4
OBJECT IDENTIFIER    

acRtcpXrBurstThreshold 1.3.6.1.4.1.5003.9.10.4.1.4.4.1
voice quality monitoring - excessive burst alert threshold. if set to -1, no alerts will be issued. Access: Online. AC INI-Param: VQMONBURSTHR
OBJECT-TYPE    
  Integer32 -1..12  

acRtcpXrDelayThreshold 1.3.6.1.4.1.5003.9.10.4.1.4.4.2
voice quality monitoring - excessive delay alert threshold. if set to -1, no alerts will be issued. Access: Online. AC INI-Param: VQMONDELAYTHR
OBJECT-TYPE    
  Integer32 -1..12  

acRtcpXrEndOofCallRvalDelayThreshold 1.3.6.1.4.1.5003.9.10.4.1.4.4.3
voice quality monitoring - end of call low quality alert threshold. if set to -1, no alerts will be issued. Access: Online. AC INI-Param: VQMONEOCRVALTHR
OBJECT-TYPE    
  Integer32 -1..12  

acRtcpXrGMin 1.3.6.1.4.1.5003.9.10.4.1.4.4.4
voice quality monitoring - minimum gap size (number of frames). Access: Online. AC INI-Param: VQMONGMIN
OBJECT-TYPE    
  Unsigned32 0..255  

acRtcpXrEnable 1.3.6.1.4.1.5003.9.10.4.1.4.4.5
Enable voice quality monitoring and RTCP xr reports. 0 = Disable 1 = Enable. Access: Offline. AC INI-Param: VQMONENABLE
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acVideoRtpRtcp 1.3.6.1.4.1.5003.9.10.4.1.4.5
OBJECT IDENTIFIER    

acVideoRtpRtcpDisableRtcpIntervalRandomization 1.3.6.1.4.1.5003.9.10.4.1.4.5.1
Determines whether to enable RTCP Interval Randomization. One of the following values: 0 Enable RTCP Interval Randomization 1 Disable RTCP Interval Randomization . Access: Online. AC INI-Param: VideoDisableRtcpIntervalRandomization
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acVideoRtpRtcpMeanTxInterval 1.3.6.1.4.1.5003.9.10.4.1.4.5.2
Defines the mean interval between two transmitted RTCP packets (milliseconds). If the interval is set to 0, no RTCP packets are transmitted at all. Access: Online. AC INI-Param: VideoRtcpMeanTxInterval
OBJECT-TYPE    
  Unsigned32 0..65535  

acVideoRtpRtcpBrokenConnectionActivationMode 1.3.6.1.4.1.5003.9.10.4.1.4.5.3
Broken connection event activation mode. 0 - Activate broken connection after the arrival of the first RTP packet. 1 - Activate broken connection immediately after the Activate RTP command. . Access: Online. AC INI-Param: VideoBrokenConnectionActivationMode
OBJECT-TYPE    
  INTEGER afterFirstIncomingRtpPacket(0), onRtpStreamActivation(1)  

acVideoRtpRtcpBrokenConnectionEventTimeout 1.3.6.1.4.1.5003.9.10.4.1.4.5.4
Timeout that defines when broken connection event occurs. Time resolution is 20msec. Access: Online. AC INI-Param: VideoBrokenConnectionEventTimeout
OBJECT-TYPE    
  Unsigned32 0..65535  

acMediaIBSConfig 1.3.6.1.4.1.5003.9.10.4.1.5
OBJECT IDENTIFIER    

acIBS 1.3.6.1.4.1.5003.9.10.4.1.5.1
OBJECT IDENTIFIER    

acIBSAnalogSignalTransportType 1.3.6.1.4.1.5003.9.10.4.1.5.1.1
Determines the analog signal transport type. 0 = Ignore 1 = Transfer hookflash via RFC 2833. Access: Online. AC INI-Param: ANALOGSIGNALTRANSPORTTYPE
OBJECT-TYPE    
  INTEGER ignore(0), transfer(1)  

acIBSDTMFVolume 1.3.6.1.4.1.5003.9.10.4.1.5.1.2
Defines and controls the DTMF generation volume [-dBm]. Range = -31 to 0. Access: Online. AC INI-Param: DTMFVOLUME
OBJECT-TYPE    
  Integer32 -31..0  

acIBSDTMFTransportType 1.3.6.1.4.1.5003.9.10.4.1.5.1.3
Defines the type of DTMF transport. 0 = Erase DTMFs from voice transport not relayed to remote 2 = DTMFs not erased are not relayed to remote 3 = DTMFs are muted from the voice stream and relayed according to RFC 2833 7 = DTMFs are sent according to RFC 2833 and muted when received. Access: Online. AC INI-Param: DTMFTRANSPORTTYPE
OBJECT-TYPE    
  INTEGER acMuteDTMF(0), acTransparentDTMF(2), acRFC2833RalayDTMF(3), acRFC2833RelayDecoderMute(7)  

acIBSMFTransportType 1.3.6.1.4.1.5003.9.10.4.1.5.1.4
Defines the type of MF transport. 0 = Erase MFs from voice transport not relayed to remote 2 = MFs not erased are not relayed to remote 3 = MFs are muted from the voice stream and relayed according to RFC 2833. Access: Online. AC INI-Param: MFTRANSPORTTYPE
OBJECT-TYPE    
  INTEGER acMuteMF(0), acTransparentMF(2), acRFC2833RalayMF(3)  

acIBSTrunkTestingTonesEnable 1.3.6.1.4.1.5003.9.10.4.1.5.1.5
Enables or disables trunk testing tones. 0 = Disables trunk testing tones 1 = Enables trunk testing tones. Access: Offline. AC INI-Param: ENABLETRUNKTESTINGTONES
OBJECT-TYPE    
  INTEGER disables(0), enables(1)  

acIBSCASRelayTransportMode 1.3.6.1.4.1.5003.9.10.4.1.5.1.6
Controls the ABCD signaling transport type over IP. 0 = No Relay over the network 1 = Enable CAS relay according to RFC 2833. Access: Online. AC INI-Param: CASTRANSPORTTYPE
OBJECT-TYPE    
  INTEGER cASEventsOnly(0), cASRFC2833Relay(1)  

acIBSRxDtmfHangOverTime 1.3.6.1.4.1.5003.9.10.4.1.5.1.7
Used to configure the Voice Silence time (in ms units) after playing DTMF or MF digits to the TDM side that arrived as Relay from the Network side. Range from 0 to 2000, Default 1000. Access: Online. AC INI-Param: RxDtmfHangOverTime
OBJECT-TYPE    
  Unsigned32 0..2000  

acIBSTxDtmfHangOverTime 1.3.6.1.4.1.5003.9.10.4.1.5.1.8
Voice Silence time (in ms units) after detecting the end of DTMF or MF digits at the TDM side when the DTMF Transport Type is either Relay or Mute.This feature allows the user to configure the silence time. . Access: Online. AC INI-Param: TxDtmfHangOverTime
OBJECT-TYPE    
  Unsigned32 0..2000  

acIBSDTMFTwistControl 1.3.6.1.4.1.5003.9.10.4.1.5.1.9
Defines a delta (in dB) between the high and low frequency component in the DTMF signal. dB Positive values cause the higher frequency component to be stronger than the lower one. Negative values cause the opposite effect. For any parameter value, both components change so that their average is constant. Range = -10 to 10. Access: Offline. AC INI-Param: DTMFGenerationTwist
OBJECT-TYPE    
  Integer32 -10..10  

acIBSNTEMaxDuration 1.3.6.1.4.1.5003.9.10.4.1.5.1.10
Maximal time for sending NTEs (Named Telephony Events) to the network, regardless of the time range when the TDM signal is detected. -1= NTE will stop only upon detection of End event (default). Access: Online. AC INI-Param: NTEMaxDuration
OBJECT-TYPE    
  Integer32 -1..200000000  

acIBSDetectors 1.3.6.1.4.1.5003.9.10.4.1.5.2
OBJECT IDENTIFIER    

acIBSDetectorsMFR1Enable 1.3.6.1.4.1.5003.9.10.4.1.5.2.1
Enables or disables detection of MFR1 signaling. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: MFR1DETECTORENABLE
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIBSDetectorsMFR2ForwardEnable 1.3.6.1.4.1.5003.9.10.4.1.5.2.2
Enables or disables detection of MFR2 forward signaling. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: MFR2FORWARDDETECTORENABLE
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIBSDetectorsMFR2BackwardEnable 1.3.6.1.4.1.5003.9.10.4.1.5.2.3
Enables or disables detection of MFR2 backward signaling. Access: Online. AC INI-Param: MFR2BACKWARDDETECTORENABLE
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIBSDetectorsR1LineEnable 1.3.6.1.4.1.5003.9.10.4.1.5.2.4
Enables or disables detection of Line signaling. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: R1LINEDETECTORENABLE
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIBSDetectorsR2LineEnable 1.3.6.1.4.1.5003.9.10.4.1.5.2.5
Enables or disables detection of Line signaling. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: R2LINEDETECTORENABLE
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIBSDetectorsAC15Enable 1.3.6.1.4.1.5003.9.10.4.1.5.2.6
Enables or disables detection of Line signaling. Access: Online. AC INI-Param: AC15DETECTORENABLE
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIBSDetectorsDTMFEnable 1.3.6.1.4.1.5003.9.10.4.1.5.2.7
Enables or disables detection of DTMF signaling. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: DTMFDETECTORENABLE
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIBSDetectorsCallProgressEnable 1.3.6.1.4.1.5003.9.10.4.1.5.2.8
Enables or disables detection of Call Progress Tones. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: CALLPROGRESSDETECTORENABLE
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIBSDetectorsUserDefinedToneEnable 1.3.6.1.4.1.5003.9.10.4.1.5.2.9
Enables or disables detection of User Defined Tones signaling. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: USERDEFINEDTONEDETECTORENABLE
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIBSDetectorsDetectionRedirection 1.3.6.1.4.1.5003.9.10.4.1.5.2.10
Determines the IBS (In-Band Signaling) Detection Direction. 0 = PCM 1 = Network. Access: Online. AC INI-Param: IBSDETECTIONREDIRECTION
OBJECT-TYPE    
  INTEGER pcm(0), network(1)  

acIBSDetectorsSS4Enable 1.3.6.1.4.1.5003.9.10.4.1.5.2.11
Enables or disables detection of Line signaling. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: SS4DETECTORENABLE
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIBSDetectorsMFSS5Enable 1.3.6.1.4.1.5003.9.10.4.1.5.2.12
Enables or disables detection of MF SS5 line signaling. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: MFSS5DETECTORENABLE
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIBSDetectorsSS5Enable 1.3.6.1.4.1.5003.9.10.4.1.5.2.13
Detection of Line signaling. 0 = Disable 1 = Enable. Access: Online. AC INI-Param: SS5DETECTORENABLE
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIBSDetectorsSITEnable 1.3.6.1.4.1.5003.9.10.4.1.5.2.14
Enables or disables SIT (Special Information Tone) detection according to the ITU-T recommendation E.180/Q.35. 0 = Disable 1 = Enable. Access: Offline. AC INI-Param: SITDETECTORENABLE
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIBSDetectorsCOTEnable 1.3.6.1.4.1.5003.9.10.4.1.5.2.15
Enables or disables Continuity Test tone detection and generation according to the ITU-T Q.724 recommendation. 0 = Disable 1 = Enable. Access: Offline. AC INI-Param: ENABLECONTINUITYTONES
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIBSDetectorsR1DetectionStandard 1.3.6.1.4.1.5003.9.10.4.1.5.2.16
This parameter determines which one of the R1 MF protocol flavors will be used for detection. 0 = ITU 1 = R1.5. Access: Offline. AC INI-Param: R1DetectionStandard
OBJECT-TYPE    
  INTEGER mfR1DetectionStandardItu(0), mfR1DetectionStandardR15(1)  

acIBSDetectorsUDTDetectorFrequencyDeviation 1.3.6.1.4.1.5003.9.10.4.1.5.2.17
Defines the deviation allowed for the detection of each signal frequency. Units are in Hertz. Valid values range 1-50. Default value 50 Hz. . Access: Offline. AC INI-Param: UDTDETECTORFREQUENCYDEVIATION
OBJECT-TYPE    
  Unsigned32 1..50  

acIBSDetectorsCPTDetectorFrequencyDeviation 1.3.6.1.4.1.5003.9.10.4.1.5.2.18
Defines the deviation allowed for the detection of each CPT signal frequency. Units are in Hertz. Valid values range 1-30. Default value 10 Hz. . Access: Offline. AC INI-Param: CPTDETECTORFREQUENCYDEVIATION
OBJECT-TYPE    
  Unsigned32 1..30  

acIPMediaConfig 1.3.6.1.4.1.5003.9.10.4.1.6
OBJECT IDENTIFIER    

acIPMedia 1.3.6.1.4.1.5003.9.10.4.1.6.1
OBJECT IDENTIFIER    

acIPMediaDSPDetectorsEnable 1.3.6.1.4.1.5003.9.10.4.1.6.1.1
Enables or disables DSP IP Media Detectors. Enabling this parameter might reduce the board channel capacity. 0 = Disable 1 = Enable. Access: Offline. AC INI-Param: ENABLEDSPIPMDETECTORS
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIPMAnswerDetector 1.3.6.1.4.1.5003.9.10.4.1.6.2
OBJECT IDENTIFIER    

acIPMAnswerDetectorEnable 1.3.6.1.4.1.5003.9.10.4.1.6.2.1
Enables or disables activation of the AD (Answer Detector). 0 = Disable 1 = Enable. Access: Online. AC INI-Param: ENABLEANSWERDETECTOR
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

acIPMAnswerDetectorActivityDelay 1.3.6.1.4.1.5003.9.10.4.1.6.2.2
Controls (in 100 msec resolution) the time between sending Activation command (AnswerDetector = 1) and the time that the detector actually starts to work. Range = 0 to 0x3FF. Access: Online. AC INI-Param: ANSWERDETECTORACTIVITYDELAY
OBJECT-TYPE    
  Unsigned32 0..128  

acIPMAnswerDetectorSilenceTime 1.3.6.1.4.1.5003.9.10.4.1.6.2.3
This parameter controls the silence time period (in 100 msec resolution) from no speech input until the END_OF_SPEECH event is sent. 10 = 1 second Range = 0 to 0x3FF. Access: Online. AC INI-Param: ANSWERDETECTORSILENCETIME
OBJECT-TYPE    
  Unsigned32 0..128  

acIPMAnswerDetectorRedirection 1.3.6.1.4.1.5003.9.10.4.1.6.2.4
Determines the AD (Answer Detector) Redirection. 0 (PCM) = Speech from the PCM side is detected 1 (Network) = Speech from the IP side is detected. Access: Online. AC INI-Param: ANSWERDETECTORREDIRECTION
OBJECT-TYPE    
  INTEGER speechPCMSideDetected(0), speechIPSideDetected(1)  

acIPMAnswerDetectorSensitivity 1.3.6.1.4.1.5003.9.10.4.1.6.2.5
Controls the AD (Answer Detector) sensitivity. The allowed values are different for different boards: DSP Gen2-based products: range 0 - 2, default 0. DSP Gen2-based products: range 0 - 7, default 3. Lowest value matches highest sensitivity and vice versa. Access: Online. AC INI-Param: ANSWERDETECTORSENSITIVITY
OBJECT-TYPE    
  Unsigned32 0..7  

acIPMEnergyDetector 1.3.6.1.4.1.5003.9.10.4.1.6.3
OBJECT IDENTIFIER    

acIPMEnergyDetectorEnable 1.3.6.1.4.1.5003.9.10.4.1.6.3.1
Activates the ED (Energy Detector). 0 = Disable 1 = Enable. Access: Online. AC INI-Param: ENABLEENERGYDETECTOR
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

acIPMEnergyDetectorQualityFactor 1.3.6.1.4.1.5003.9.10.4.1.6.3.2
Determines the ED's (Energy Detector's) sensitivity (0 -10). 0 = Insensitive 10 = Most Sensitive Range = 0 to 10. Access: Online. AC INI-Param: ENERGYDETECTORQUALITYFACTOR
OBJECT-TYPE    
  Unsigned32 0..10  

acIPMEnergyDetectorThreshold 1.3.6.1.4.1.5003.9.10.4.1.6.3.3
Defines the ED's (Energy Detector's) threshold. A signal exceeding the threshold invokes an 'Above' or 'Below' event. ActualThreshold = -44 dBm + (EDThreshold * 6) Default = 3 = -26 dBm Range: 0 to 7. Access: Online. AC INI-Param: ENERGYDETECTORTHRESHOLD
OBJECT-TYPE    
  Unsigned32 0..7  

acIPMEnergyDetectorEnergyRedirection 1.3.6.1.4.1.5003.9.10.4.1.6.3.4
Selects the direction of the energy detection. 0 = Detect from the TDM side 1 = Detect from the network side. Access: Online. AC INI-Param: ENERGYDETECTORREDIRECTION
OBJECT-TYPE    
  INTEGER tDM(0), network(1)  

acIPMediaPatternDetector 1.3.6.1.4.1.5003.9.10.4.1.6.4
OBJECT IDENTIFIER    

acIPMediaPatternDetectorEnable 1.3.6.1.4.1.5003.9.10.4.1.6.4.1
Enables or disables activation of the PD (Pattern Detector). 0 = Disable 1 = Enable. Access: Online. AC INI-Param: ENABLEPATTERNDETECTOR
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

acIPMediaPatternDetectorDetectionThreshold 1.3.6.1.4.1.5003.9.10.4.1.6.4.2
Defines the number of consecutive patterns to trigger the pattern detection event. Range = 0 to 31. Access: Offline. AC INI-Param: PDTHRESHOLD
OBJECT-TYPE    
  Unsigned32 0..31  

acIPMediaAMD 1.3.6.1.4.1.5003.9.10.4.1.6.5
OBJECT IDENTIFIER    

acIPMediaAMDDetectionDirection 1.3.6.1.4.1.5003.9.10.4.1.6.5.1
Determines the AMD (Answer Machine Detector) detection direction. One of the following values: 0 = Detection from the TDM side 1 = Detection from the Network side. Access: Online. AC INI-Param: AMDDETECTIONDIRECTION
OBJECT-TYPE    
  INTEGER acAmdTdmDetection(0), acAmdNetworkDetection(1)  

acIPMediaAMDSensitivity 1.3.6.1.4.1.5003.9.10.4.1.6.5.2
Determines the AMD (Answer Machine Detector) detection sensitivity: 0 = Best detection of an answering machine 7 = Best detection of a live call. Access: Online. AC INI-Param: AMDDetectionSensitivity
OBJECT-TYPE    
  Unsigned32 0..7  

acIPMediaAMDDetectionSensitivityHighResolution 1.3.6.1.4.1.5003.9.10.4.1.6.5.3
Determines the AMD (Answer Machine Detector) high resolution detection sensitivity. The high resolution has 16 levels of sensitivity while the normal resolution (Answer Machine Detector Sensitivity) has 8 levels. 0 = Best detection of an answering machine 15 = Best detection of a live call. Access: Online. AC INI-Param: AMDDetectionSensitivityHighResolution
OBJECT-TYPE    
  Unsigned32 0..15  

acIPMediaAMDSensitivityResolution 1.3.6.1.4.1.5003.9.10.4.1.6.5.4
Determines the AMD (Answer Machine Detector) detection sensitivity resolution: 0 = Normal detection sensitivity resolution (8 sensitivity levels) 1 = High detection sensitivity resolution (16 sensitivity levels). Access: Online. AC INI-Param: AMDSensitivityResolution
OBJECT-TYPE    
  INTEGER normal(0), high(1)  

acIPMediaAMDBeepDetectionTimeout 1.3.6.1.4.1.5003.9.10.4.1.6.5.5
Determines the AMD (Answer Machine Detector) Beep detection timeout. Units of 100 milliseconds, values from 0 to 1638 (163.8 seconds). Access: Online. AC INI-Param: AMDBeepDetectionTimeout
OBJECT-TYPE    
  Unsigned32 0..1638  

acIPMediaAMDBeepDetectionSensitivity 1.3.6.1.4.1.5003.9.10.4.1.6.5.6
Determines the AMD (Answer Machine Detector) Beep detection sensitivity. 0 - Least sensitive. 3 - Most sensitive. Access: Online. AC INI-Param: AMDBeepDetectionSensitivity
OBJECT-TYPE    
  Unsigned32 0..3  

acIPMConference 1.3.6.1.4.1.5003.9.10.4.1.6.6
OBJECT IDENTIFIER    

acIPMConferenceGASNMinInterval 1.3.6.1.4.1.5003.9.10.4.1.6.6.1
Minimum interval between Active Speaker Notification (ASN) events. An ASN event reports on the active speakers in a conference. The event is issued whenever the active speakers change. units = 100 ms Minimum configurable interval between events is 500 ms (5 units). Access: Instant. AC INI-Param: ACTIVESPEAKERSNOTIFICATIONMININTERVAL
OBJECT-TYPE    
  Unsigned32 10..65535  

acIPMConferenceEnergythreshold 1.3.6.1.4.1.5003.9.10.4.1.6.6.2
Conference - Minimum energy level for a user to be included in Active Speaker Notification (ASN) events (units: -dBm). Valid range 0 to (-39) dbm. Access: Instant. AC INI-Param: ActiveSpeakerEnergyThreshold
OBJECT-TYPE    
  Unsigned32 0..39  

acIPMConferenceEnableHDConference 1.3.6.1.4.1.5003.9.10.4.1.6.6.3
Enable\Disable HD Conference. Access: Offline. AC INI-Param: EnableHDConference
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIPMVideoConference 1.3.6.1.4.1.5003.9.10.4.1.6.7
OBJECT IDENTIFIER    

acIPMVideoConferenceSwitchingInterval 1.3.6.1.4.1.5003.9.10.4.1.6.7.1
Determines the video view rotation interval in seconds. Applicable when using timer trigger switching mode. Access: Online. AC INI-Param: VideoConferenceSwitchingInterval
OBJECT-TYPE    
  Unsigned32 0..65535  

acIPMVideoConferenceEnableActiveSpeakerHighlight 1.3.6.1.4.1.5003.9.10.4.1.6.7.2
Highlights the speaker for participants viewing a symmetric layout (2x2 or 3x3) . 0 - Don't highlight active speaker. 1 - Highlight active speaker. Access: Online. AC INI-Param: VideoEnableActiveSpeakerHighlight
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIPMVideoConferenceParticipantType 1.3.6.1.4.1.5003.9.10.4.1.6.7.3
Indicates a participant's capabilities in the conference. Regular (2) ? Regular participant who is able to both send and receive video. . Access: Online. AC INI-Param: VideoConferenceParticipantType
OBJECT-TYPE    
  INTEGER regular(2)  

acIPMVideoConferenceParticipantTriggerMode 1.3.6.1.4.1.5003.9.10.4.1.6.7.4
Participant trigger mode defines the trigger for modifying the participant's view. Voice Activated Video Switch (0) ? A participant?s view will be changed according to the active speakers? detection. Timer (1) ? A participant?s view is rotated every configured time among the different video participants in the conference. Fixed (3) ? A participant?s view is fixed. . Access: Online. AC INI-Param: VideoConferenceParticipantTriggerMode
OBJECT-TYPE    
  INTEGER triggerMode-Speaker(0), triggerMode-Timer(1), triggerMode-Fixed(3)  

acIPMVideoConferenceParticipantLayout 1.3.6.1.4.1.5003.9.10.4.1.6.7.5
Indicates the participant's view layout. 1 user (0). 2*2 users (1). All same size. 3*3 users (2). All same size. . Access: Online. AC INI-Param: VideoConferenceParticipantLayout
OBJECT-TYPE    
  INTEGER layout-1XUSER(0), layout-2x2-USERS(1), layout-3x3-USERS(2)  

acIPMVideoConferenceEnableConferenceParticipantSelfView 1.3.6.1.4.1.5003.9.10.4.1.6.7.6
Self view indication. 0 - The participant cannot view himself 1 - The participant can view himself. Access: Online. AC INI-Param: VideoEnableConferenceParticipantSelfView
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acMediaCallerIDConfig 1.3.6.1.4.1.5003.9.10.4.1.7
OBJECT IDENTIFIER    

acCallerID 1.3.6.1.4.1.5003.9.10.4.1.7.1
OBJECT IDENTIFIER    

acCallerIDTypes 1.3.6.1.4.1.5003.9.10.4.1.7.1.1
Defines the supported Caller ID standard. 0 = Bellcore 1 = ETSI 2 = NTT 4 = British 16 = ETSI_ETS 17 = Denmark 18 = Indian 19 = Brazilian. Access: Online. AC INI-Param: CALLERIDTYPE
OBJECT-TYPE    
  INTEGER bellcore(0), eTSI(1), nTT(2), bT(4), dTMF-Based-ETSI(16), denmark(17), indian(18), brazilian(19)  

acCallerIDTransportType 1.3.6.1.4.1.5003.9.10.4.1.7.1.2
Defines the CallerID Transport type. 0 = Disable 1 = Relay 3 = Mute. Access: Online. AC INI-Param: CallerIDTransportType
OBJECT-TYPE    
  INTEGER callerID-DISABLE(0), callerID-RELAY(1), callerID-MUTE(3)  

acCallerIDDTMFBasedMaxDigits 1.3.6.1.4.1.5003.9.10.4.1.7.1.3
Determines the maximum number of DTMF digits in a DTMF-based Caller ID string. Range = 0 to 26. Access: Online. AC INI-Param: MAXDTMFDIGITSINCIDSTRING
OBJECT-TYPE    
  Unsigned32 0..26  

acCallerIDDTMFBasedMinDigits 1.3.6.1.4.1.5003.9.10.4.1.7.1.4
Determines the mimumum number of DTMF digits in a DTMF-based Caller ID string. Range = 0 to 26. Access: Online. AC INI-Param: MINDTMFDIGITSINCIDSTRING
OBJECT-TYPE    
  Unsigned32 0..26  

acCallerIDNTTDIDSignallingForm 1.3.6.1.4.1.5003.9.10.4.1.7.1.5
Configures the signalling format used when generating an NTT DID. 0 = FSK Siganl 1 = DTMF Based Signal. Access: Online. AC INI-Param: NTTDIDSignallingForm
OBJECT-TYPE    
  INTEGER nttDidFskSignalling(0), nttDidDtmfBasedSignalling(1)  

acMediaNetworkConfig 1.3.6.1.4.1.5003.9.10.4.1.8
OBJECT IDENTIFIER    

acMediaNetwork 1.3.6.1.4.1.5003.9.10.4.1.8.1
OBJECT IDENTIFIER    

acMediaNetworkDisableNAT 1.3.6.1.4.1.5003.9.10.4.1.8.1.1
Enables or disables the NAT feature. 0 = Do not disable NAT 1 = Disable NAT. Access: Online. AC INI-Param: DISABLENAT
OBJECT-TYPE    
  INTEGER no(0), yes(1)  

acMediaNetworkRtpIpTos 1.3.6.1.4.1.5003.9.10.4.1.8.1.2
Sets value of IP Type Of Service field in IP header for all packets generated from this channel. Follow the acTIPTOS enumeration. Access: Instant. AC INI-Param: IPTOS
OBJECT-TYPE    
  Unsigned32 0..15  

acMediaNetworkRtpIpPrecedence 1.3.6.1.4.1.5003.9.10.4.1.8.1.3
Sets value of the IP precedence field in the IP header for all packets generated from this channel. Follow the acTIPPrecedence enumeration. Access: Instant. AC INI-Param: IPPRECEDENCE
OBJECT-TYPE    
  Unsigned32 0..7  

acMediaNetworkIPDiffServ 1.3.6.1.4.1.5003.9.10.4.1.8.1.4
Defines the value of the 'DiffServ' field in the IP header for media (RTP) traffic. Range: 0 to 63. Access: Instant. AC INI-Param: IPDIFFSERV
OBJECT-TYPE    
  Unsigned32 0..63  

acMediaNetworkInboundLatchMode 1.3.6.1.4.1.5003.9.10.4.1.8.1.5
Determines the way of handling incoming media packets from non-expected address/port. Access: Online. AC INI-Param: InboundMediaLatchMode
OBJECT-TYPE    
  INTEGER strict(0), dynamic(1)  

acMediaJBConfig 1.3.6.1.4.1.5003.9.10.4.1.9
OBJECT IDENTIFIER    

acJitterBuffer 1.3.6.1.4.1.5003.9.10.4.1.9.1
OBJECT IDENTIFIER    

acJitterBufferMinDelay 1.3.6.1.4.1.5003.9.10.4.1.9.1.1
Defines the Dynamic Jitter Buffer Minimum Delay (in msec). Recommended value for a regular voice call is 10. Access: Online. AC INI-Param: DJBUFMINDELAY
OBJECT-TYPE    
  Unsigned32 0..150  

acJitterBufferOptFactor 1.3.6.1.4.1.5003.9.10.4.1.9.1.2
Defines the Dynamic Jitter Buffer frame error/delay optimization. Recommended value for a regular voice call is 10. Access: Online. AC INI-Param: DJBUFOPTFACTOR
OBJECT-TYPE    
  Unsigned32 0..13  

acVideoJitterBuffer 1.3.6.1.4.1.5003.9.10.4.1.9.2
OBJECT IDENTIFIER    

acVideoJitterBufferMinDelay 1.3.6.1.4.1.5003.9.10.4.1.9.2.1
Jitter buffer minimum delay in milliseconds. Must be less than JitterBufferMaxDelay. Access: Online. AC INI-Param: VideoJitterBufferMinDelay
OBJECT-TYPE    
  Unsigned32 0..500  

acVideoJitterBufferMaxDelay 1.3.6.1.4.1.5003.9.10.4.1.9.2.2
Jitter buffer maximum delay in milliseconds. Access: Online. AC INI-Param: VideoJitterBufferMaxDelay
OBJECT-TYPE    
  Unsigned32 0..500  

acVideoJitterBufferDJBOptimizationFactor 1.3.6.1.4.1.5003.9.10.4.1.9.2.3
JB Optimization Factor controls the jitter buffer's adaptation rates A High factor means fast adaptation when jitter increases, and a slow adaptation when jitter decrease. Small factor means slow adaptation when jitter increases, and a fast adaptation when jitter decreases. . Access: Online. AC INI-Param: VideoDJBOptimizationFactor
OBJECT-TYPE    
  Unsigned32 0..10  

acMediaStatus 1.3.6.1.4.1.5003.9.10.4.2
OBJECT IDENTIFIER    

acMediaAggregation 1.3.6.1.4.1.5003.9.10.4.1.10
OBJECT IDENTIFIER    

acMediaAggregationRemoteBaseUDPPort 1.3.6.1.4.1.5003.9.10.4.1.10.1
Remote Base UDP Port For Aggrigation. Access: Offline. AC INI-Param: REMOTEBASEUDPPORT
OBJECT-TYPE    
  Unsigned32 0..65535  

acMediaAggregationL1L1ComplexRxUDPPort 1.3.6.1.4.1.5003.9.10.4.1.10.2
The UDP port for the incoming (from the remote side) and the outgoing (destination UDP) packets, for Complex Multiplexed RTP mode. Access: Offline. AC INI-Param: L1L1ComplexRxUDPPort
OBJECT-TYPE    
  Unsigned32 0..65535  

acMediaAggregationL1L1ComplexTxUDPPort 1.3.6.1.4.1.5003.9.10.4.1.10.3
The Source UDP port for the outgoing UDP Multiplexed RTP packets, for Complex-Multiplex RTP mode. Access: Offline. AC INI-Param: L1L1ComplexTxUDPPort
OBJECT-TYPE    
  Unsigned32 0..65535  

acIPLegs 1.3.6.1.4.1.5003.9.10.4.2.1
OBJECT IDENTIFIER    

acIPLegsTable 1.3.6.1.4.1.5003.9.10.4.2.1.1
Tok_String
OBJECT-TYPE    
  SEQUENCE OF  
    AcIPLegsEntry

acIPLegsEntry 1.3.6.1.4.1.5003.9.10.4.2.1.1.1
Tok_String
OBJECT-TYPE    
  AcIPLegsEntry  

acIPLegsLegIndex 1.3.6.1.4.1.5003.9.10.4.2.1.1.1.1
Describes Rtp Endpoint In A Specific Call. AC INI-Param: N/A
OBJECT-TYPE    
  Unsigned32 0..5000  

acIPLegsCallIndex 1.3.6.1.4.1.5003.9.10.4.2.1.1.1.2
Decribes The Call which The Rtp EndPoint Participant In It. AC INI-Param: N/A
OBJECT-TYPE    
  Unsigned32 0..5000  

acIPLegsRTPActive 1.3.6.1.4.1.5003.9.10.4.2.1.1.1.3
Decribes whether the RTP is active or not. AC INI-Param: N/A
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIPLegsCoderType 1.3.6.1.4.1.5003.9.10.4.2.1.1.1.4
describes the coder Type. AC INI-Param: N/A
OBJECT-TYPE    
  INTEGER acG711Alaw-64(0), acG711Mulaw(1), acG726-16(2), acG726-24(3), acG726-32(4), acG726-40(5), acG727-16(6), acG727-24-16(7), acG727-24(8), acG727-32-16(9), acG727-32-24(10), acG727-32(11), acG727-40-16(12), acG727-40-24(13), acG727-40-32(14), acG723Low(15), acG723High(16), acG729(17), acGSM610(18), vacGSM610MS(20), acGSM-EFR(21), acTransparent(22), acG728(23), acNetCoder-4-8(25), acNetCoder-5-6(26), acNetCoder-6-4(27), acNetCoder-7-2(28), acNetCoder-8(29), acNetCoder-8-8(30), acNetCoder-9-(31), acEVRC(32), acEVRC-TFO(33), acQCELP-8(34), acQCELP-8-TFO(35), acQCELP-13(36), acQCELP-13-TFO(37), acEVRC-TTY(38), acNoCoder(40), acModemAnswer(41), acModemCall(42), acVoxADPCM(43), acG711Alaw-5-5(45), acG711Mulaw-5-5(46), acG726-32-5-5(47), acG729E(48), acLinearPCM(49), acAMR-4-7(50), acAMR-5-15(51), acAMR-5-9(52), acAMR-6-7(53), acAMR-7-4(54), acAMR-7-95(55), acAMR-10-2(56), acAMR-12-2(57), acEVRC-B(58), acEVRC-TFOV(60), acQCELP-8-TFOV(61), acQCELP-13-TFOV(62), acILBC-15(63), acILBC-13(64), acBV-16(65), acAMRWB-6-6(66), acAMRWB-8-85(67), acAMRWB-12-65(68), acAMRWB-14-25(69), acAMRWB-15-85(70), acAMRWB-18-25(71), acAMRWB-19-85(72), acAMRWB-23-05(73), acAMRWB-23-85(74), acG722-48K(75), acG722-56K(76), acG722-64K(77), acDPNSSCoder(78), acEG711Alaw-10ms(80), acEG711Alaw-20ms(81), acEG711Alaw-30ms(82), acEG711Mulaw-10ms(83), acEG711Mulaw-20ms(84), acEG711Mulaw-30ms(85)  

acIPLegsSilenceCompression 1.3.6.1.4.1.5003.9.10.4.2.1.1.1.5
Enables or Disables the Silence Compression. AC INI-Param: N/A
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIPLegsDTMFDetection 1.3.6.1.4.1.5003.9.10.4.2.1.1.1.6
Enables or Disables the DTMF Detection. AC INI-Param: N/A
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIPLegsLocalRTPPort 1.3.6.1.4.1.5003.9.10.4.2.1.1.1.7
Describes the RTP port of the Leg. AC INI-Param: N/A
OBJECT-TYPE    
  Unsigned32 0..20000  

acIPLegsRemoteRTPAddress 1.3.6.1.4.1.5003.9.10.4.2.1.1.1.8
Describes the RTP address. AC INI-Param: N/A
OBJECT-TYPE    
  IpAddress  

acIPLegsFaxTransportType 1.3.6.1.4.1.5003.9.10.4.2.1.1.1.9
Describes the Fax transfor Type currently working. AC INI-Param: N/A
OBJECT-TYPE    
  INTEGER transparent(0), relay(1), bypass(2), withevents(3)  

acIPLegsRxPackets 1.3.6.1.4.1.5003.9.10.4.2.1.1.1.10
Describes the received packets on the Leg. AC INI-Param: N/A
OBJECT-TYPE    
  Unsigned32 0..2147483647  

acIPLegsTxPackets 1.3.6.1.4.1.5003.9.10.4.2.1.1.1.11
Describes the Transmitted packets on the Leg. AC INI-Param: N/A
OBJECT-TYPE    
  Unsigned32 0..2147483647  

acIPLegsRxBytes 1.3.6.1.4.1.5003.9.10.4.2.1.1.1.12
Describes the received Bytes on the Leg. AC INI-Param: N/A
OBJECT-TYPE    
  Unsigned32 0..2147483647  

acIPLegsTxBytes 1.3.6.1.4.1.5003.9.10.4.2.1.1.1.13
Describes the Transmitted packets on the Leg. AC INI-Param: N/A
OBJECT-TYPE    
  Unsigned32 0..2147483647  

acIPLegsJitter 1.3.6.1.4.1.5003.9.10.4.2.1.1.1.14
Describes the Jitter on the Leg. AC INI-Param: N/A
OBJECT-TYPE    
  Unsigned32 0..2147483647  

acIPLegsPacketLoss 1.3.6.1.4.1.5003.9.10.4.2.1.1.1.15
Describes the Lost packets on the Leg. AC INI-Param: N/A
OBJECT-TYPE    
  Unsigned32 0..2147483647  

acIPLegsSSRCOfSender 1.3.6.1.4.1.5003.9.10.4.2.1.1.1.16
Describes the SSRC Of the Sender. AC INI-Param: N/A
OBJECT-TYPE    
  Unsigned32 0..2147483647  

acIPLegsDSPDevice 1.3.6.1.4.1.5003.9.10.4.2.1.1.1.17
Describes the DSP Device Of the Leg. AC INI-Param: N/A
OBJECT-TYPE    
  Unsigned32 0..2000  

acIPLegsLegName 1.3.6.1.4.1.5003.9.10.4.2.1.1.1.18
Describes the Leg Name as in the Control Protocol. AC INI-Param: N/A
OBJECT-TYPE    
  SnmpAdminString Size(0..64)  

acStreamingCache 1.3.6.1.4.1.5003.9.10.4.1.11
OBJECT IDENTIFIER    

acStreamingCacheSize 1.3.6.1.4.1.5003.9.10.4.1.11.1
Sets the streaming cache size in MBs. The remaining size (out of 32MBs) is used as VoicePrompt storage. Access: Offline. AC INI-Param: gStreamingCacheSize
OBJECT-TYPE    
  Unsigned32 0..32  

acStreamingCacheRefreshTime 1.3.6.1.4.1.5003.9.10.4.1.11.2
Defines the streaming cache data refresh time in minutes. If -1 is set, refresh is off. Access: Offline. AC INI-Param: gStreamingCacheRefreshTime
OBJECT-TYPE    
  Integer32 -1..65535  

acStreamingCacheClearService 1.3.6.1.4.1.5003.9.10.4.1.11.3
reset the streaming cache. Access: Instant. AC INI-Param: N/A
OBJECT-TYPE    
  Unsigned32 1..2  

acMediaVideoConfig 1.3.6.1.4.1.5003.9.10.4.1.12
OBJECT IDENTIFIER    

acMediaVideoConfigEncoderIntraInterval 1.3.6.1.4.1.5003.9.10.4.1.12.1
Sets the frequency for the number of frames at which the encoder outputs an Intra frame. Access: Online. AC INI-Param: VideoEncoderIntraInterval
OBJECT-TYPE    
  Unsigned32 0..65535  

acMediaVideoConfigMaxPacketSize 1.3.6.1.4.1.5003.9.10.4.1.12.2
Sets the maximum packet size in bytes. Access: Online. AC INI-Param: VideoMaxPacketSize
OBJECT-TYPE    
  Unsigned32 1..1400  

acMediaVideoConfigTargetBitrate 1.3.6.1.4.1.5003.9.10.4.1.12.3
Sets the target output bit rate. Access: Online. AC INI-Param: VideoTargetBitrate
OBJECT-TYPE    
  Unsigned32 1..384  

acMediaVideoConfigQualityParameterForRateControl 1.3.6.1.4.1.5003.9.10.4.1.12.4
This value determines the trade off between video quality and frame rate. A low value indicates a higher quality with a lower frame rate and vice versa. Access: Online. AC INI-Param: VideoQualityParameterForRateControl
OBJECT-TYPE    
  Unsigned32 0..31  

acMediaVideoConfigRateControlType 1.3.6.1.4.1.5003.9.10.4.1.12.5
Sets bitrate output to either a constant or a variable bit rate. CBR (0) ? Constant Bit Rate. VBR (1) ? Variable Bit Rate. Target Bitrate indicates the target average output bit rate. . Access: Online. AC INI-Param: VideoRateControlType
OBJECT-TYPE    
  INTEGER ceVideoConstantBitRate(0), ceVideoVaribleBitRate(1)  

acMediaVideoConfigEnableReSyncHeader 1.3.6.1.4.1.5003.9.10.4.1.12.6
Indicates whether to add a video packet header to every packet in order to increase error resilience. 0 - Disable 1 - Enable. Access: Online. AC INI-Param: VideoEnableReSyncHeader
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acMediaVideoConfigEnableAudioVideoSynchronization 1.3.6.1.4.1.5003.9.10.4.1.12.7
Determines whether to enable audio and video synchronization. 0 - No synchronization between audio and video streams 1 - Synchronization between audio and video streams . Access: Online. AC INI-Param: EnableAudioVideoSynchronization
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIPMediaChannels 1.3.6.1.4.1.5003.9.10.4.1.13
OBJECT IDENTIFIER    

acIPMediaChannelsEnable 1.3.6.1.4.1.5003.9.10.4.1.13.1
Whether to enable DSP channels reservation for IPmedia support. Relevant for Mediant 1000 board only. One of the following possible 0 = Disable 1 - Enable. Access: Offline. AC INI-Param: EnableIPMediaChannels
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

acIPMediaChannelsResourcesTable 1.3.6.1.4.1.5003.9.10.4.1.13.21
IPMedia channels info
OBJECT-TYPE    
  SEQUENCE OF  
    AcIPMediaChannelsResourcesEntry

acIPMediaChannelsResourcesEntry 1.3.6.1.4.1.5003.9.10.4.1.13.21.1
Tok_String
OBJECT-TYPE    
  AcIPMediaChannelsResourcesEntry  

acIPMediaChannelsResourcesIndex 1.3.6.1.4.1.5003.9.10.4.1.13.21.1.1
Index Field for line. Internal parameter. AC INI-Param: IPMediaChannels_Index
OBJECT-TYPE    
  Unsigned32 0..5  

acIPMediaChannelsResourcesRowStatus 1.3.6.1.4.1.5003.9.10.4.1.13.21.1.2
ROWSTATUS field for line. Internal parameter. AC INI-Param: N/A
OBJECT-TYPE    
  RowStatus  

acIPMediaChannelsResourcesAction 1.3.6.1.4.1.5003.9.10.4.1.13.21.1.3
Mangement Field for ACTIONS. Internal parameter. AC INI-Param: N/A
OBJECT-TYPE    
  INTEGER none(0)  

acIPMediaChannelsResourcesActionRes 1.3.6.1.4.1.5003.9.10.4.1.13.21.1.4
Mangement Field for ACTIONS RESULT. Internal parameter. AC INI-Param: N/A
OBJECT-TYPE    
  INTEGER succeeded(0)  

acIPMediaChannelsResourcesModuleID 1.3.6.1.4.1.5003.9.10.4.1.13.21.1.5
Refers to M1K board only, module at which slot. Access: Offline. AC INI-Param: IPMediaChannels_ModuleID
OBJECT-TYPE    
  Unsigned32 0..6  

acIPMediaChannelsResourcesDSPChannelsReserved 1.3.6.1.4.1.5003.9.10.4.1.13.21.1.6
How many DSP channels reserve for IPMedia channels. Access: Offline. AC INI-Param: IPMediaChannels_DSPChannelsReserved
OBJECT-TYPE    
  Unsigned32 0..10000