ZYXEL-IES5000-MIB

File: ZYXEL-IES5000-MIB.mib (1060140 bytes)

Imported modules

RFC1155-SMI SNMPv2-SMI RFC1213-MIB
SNMPv2-TC Q-BRIDGE-MIB P-BRIDGE-MIB
BRIDGE-MIB VDSL-LINE-MIB IEEE8021-CFM-MIB
INET-ADDRESS-MIB VDSL2-LINE-MIB IF-MIB

Imported symbols

enterprises IpAddress TimeTicks
OBJECT-TYPE Counter64 Counter32
Gauge32 Unsigned32 Integer32
NOTIFICATION-TYPE DisplayString PhysAddress
ifIndex RowStatus TEXTUAL-CONVENTION
VlanIndex PortList dot1qVlanIndex
dot1dTrafficClass EnabledStatus MacAddress
Timeout BridgeId dot1dBasePort
vdslPhysSide vdslChanCurrTxRate vdslLineConfProfileName
vdslLineAlarmConfProfileName dot1agCfmMdIndex dot1agCfmMaIndex
dot1agCfmMepIdentifier dot1agCfmMdMdLevel dot1agCfmVlanPrimaryVid
InetAddressType InetAddress xdsl2PMChHist15MUnit
xdsl2PMChHist15MInterval xdsl2PMLHist1DUnit xdsl2PMLHist1DInterval
xdsl2PMLHist15MUnit xdsl2PMLHist15MInterval xdsl2PMChHist1DUnit
xdsl2PMChHist1DInterval xdsl2PMLCurrUnit xdsl2LConfProfProfileName
xdsl2ChConfProfProfileName xdsl2LineAlarmConfProfileName xdsl2LineBand
xdsl2LConfTempTemplateName xdsl2LAlarmConfTempTemplateName xdsl2ChAlarmConfProfileName
xdsl2SCStatusDirection xdsl2SCStatusBand InterfaceIndex

Defined Types

Xdsl2ConfigRtxMode  
Forbidden(0) - Support for G998.4 is disabled. Preferred(1) - If G998.4 is supported by the far-end, it is enabled. Forced(2) - The line will only train if G998.4 can be enabled. Test(3) - G998.4 is enabled in test mode (refer to G998.4, Clause 10.4).
TEXTUAL-CONVENTION    
  INTEGER forbidden(0), preferred(1), forced(2), test(3)  

Xdsl2StatusActualRaMode  
fixedRateMode(1) - Fixed rate mode raInit(2) - Adaptive rate mode at initialization dynamicRa(3) - Dynamic rate adaptation sosEnabled(4) - SOS enabled
TEXTUAL-CONVENTION    
  INTEGER none(0), fixedRateMode(1), raInit(2), dynamicRa(3), sosEnabled(4)  

Xdsl2StatusRtxMode  
rtxInUse(1) - RTX in use. rtxForbidden(2) - RTX not in use because RTX_MODE = FORBIDDEN. rtxNotSupportedXtuC(3) - RTX not in use because it is not supported by the XTU-C. rtxNotSupportedXtuR(4) - RTX not in use because it is not supported by the XTU-R. rtxNotSupportedBoth(5) - RTX not in use because it is not supported by the XTU-C and XTU-R.
TEXTUAL-CONVENTION    
  INTEGER none(0), rtxInUse(1), rtxForbidden(2), rtxNotSupportedXtuC(3), rtxNotSupportedXtuR(4), rtxNotSupportedBoth(5)  

Unsigned64  
A non-negative 64-bit bit integer, without counter semantics.
TEXTUAL-CONVENTION    
  Counter64  

DhcpRelay82Entry  
SEQUENCE    
  dhcpRelay82PrimaryServer IpAddress
  dhcpRelay82SecondaryServer IpAddress
  dhcpRelay82ActiveServer INTEGER
  dhcpRelay82Enable INTEGER
  dhcpRelay82Info DisplayString
  dhcpRelay82RelayMode INTEGER
  dhcpRelay82RowStatus RowStatus
  dhcpRelay82Suboption2Enable INTEGER
  dhcpRelay82Suboption2Info DisplayString
  dhcpRelay82Option82Mode INTEGER

RadiusServerEntry  
SEQUENCE    
  radiusServerIndex INTEGER
  radiusServerIp IpAddress
  radiusServerPort INTEGER
  radiusServerSecret DisplayString

Dot1xPortEntry  
SEQUENCE    
  dot1xPortEnable INTEGER
  dot1xPortControl INTEGER
  dot1xPortReAuthEnable INTEGER
  dot1xPortReAuthPeriod INTEGER

MacFilterPortEntry  
SEQUENCE    
  macFilterPortEnable INTEGER
  macFilterPortMacCount INTEGER
  macFilterPortFilterMode INTEGER

MacFilterEntry  
SEQUENCE    
  macFilterAddr PhysAddress
  macFilterRowStatus RowStatus

OuiFilterEntry  
SEQUENCE    
  ouiFilterAddr OCTET STRING
  ouiFilterRowStatus RowStatus

MacFilterStatusEntry  
SEQUENCE    
  macFilterStatusId INTEGER
  macFilterStatusAddr PhysAddress

MacFilterPerPVCEntry  
SEQUENCE    
  macFilterPerPVCVpi INTEGER
  macFilterPerPVCVci INTEGER
  macFilterPerPVCEnable INTEGER
  macFilterPerPVCMode INTEGER
  macFilterPerPVCMacCount INTEGER

MacFilterPerPVCMACEntry  
SEQUENCE    
  macFilterPerPVCMACVpi INTEGER
  macFilterPerPVCMACVci INTEGER
  macFilterPerPVCMACAddr PhysAddress
  macFilterPerPVCMACRowStatus RowStatus

PktFilterPortEntry  
SEQUENCE    
  pktFilter INTEGER

PktFilterPerPVCEntry  
SEQUENCE    
  pktFilterPerPVCVpi INTEGER
  pktFilterPerPVCVci INTEGER
  pktFilterPerPVCpktFilter INTEGER

DhcpSnoopPortEntry  
SEQUENCE    
  dhcpSnoopEnable INTEGER

DhcpStaticEntry  
SEQUENCE    
  dhcpStaticIpAddr IpAddress
  dhcpStaticRowStatus RowStatus

DhcpSnoopLan2lanEntry  
SEQUENCE    
  dhcpSnoopLan2lanEnable INTEGER

AclSetEntry  
SEQUENCE    
  aclSetVpi INTEGER
  aclSetVci INTEGER
  aclSetProfileName DisplayString
  aclSetRowStatus RowStatus

AclNoMatchEntry  
SEQUENCE    
  aclNoMatchAction INTEGER

PppoeAgentEntry  
SEQUENCE    
  pppoeAgentEnable INTEGER
  pppoeAgentInfo DisplayString
  pppoeAgentRowStatus RowStatus
  pppoeAgentOptionMode INTEGER

DsBcastEntry  
SEQUENCE    
  dsBcastRowStatus RowStatus

DscpMappingEntry  
SEQUENCE    
  dscpMappingSrcCodePoint INTEGER
  dscpMappingMapPriority INTEGER

DscpPortEntry  
SEQUENCE    
  dscpPortEnable INTEGER

SubnetvlanEntry  
SEQUENCE    
  subnetvlanIp IpAddress
  subnetvlanMask INTEGER
  subnetvlanVid INTEGER
  subnetvlanPriority INTEGER
  subnetvlanName DisplayString
  subnetvlanRowStatus RowStatus

SubnetvlanInetEntry  
SEQUENCE    
  subnetvlanInetAddrType InetAddressType
  subnetvlanInetAddr InetAddress
  subnetvlanInetMask INTEGER
  subnetvlanInetVid INTEGER
  subnetvlanInetPriority INTEGER
  subnetvlanInetName DisplayString
  subnetvlanInetRowStatus RowStatus

LoopguardEntry  
SEQUENCE    
  loopguardStatus INTEGER
  loopguardMode INTEGER
  loopguardRecoverTime INTEGER

UsStormEntry  
SEQUENCE    
  usStormBcastThresh INTEGER
  usStormMcastThresh INTEGER
  usStormUcastThresh INTEGER

ArpInspectionEntry  
SEQUENCE    
  arpInspectionEnable INTEGER

MacFFStaticEntry  
SEQUENCE    
  macFFStaticIndex INTEGER
  macFFStaticSrcIP IpAddress
  macFFStaticMask INTEGER
  macFFStaticArasIP IpAddress
  macFFStaticVid INTEGER
  macFFStaticRowStatus RowStatus

MacFFDynamicEntry  
SEQUENCE    
  macFFDynamicIndex INTEGER
  macFFDynamicSrcIP IpAddress
  macFFDynamicMask INTEGER
  macFFDynamicArasIP IpAddress
  macFFDynamicVid INTEGER

MacFFVlanEntry  
SEQUENCE    
  macFFVlanVid INTEGER
  macFFVlanRowStatus RowStatus

Dhcpv6RelayEntry  
SEQUENCE    
  dhcpv6RelayLdraState INTEGER
  dhcpv6RelayRowStatus RowStatus

Dhcpv6RelayOptionEntry  
SEQUENCE    
  dhcpv6RelayOptionId INTEGER
  dhcpv6RelayOptionState INTEGER
  dhcpv6RelayOptionFormat OCTET STRING

AlarmConfEntry  
SEQUENCE    
  alarmConfId INTEGER
  alarmConfFacility INTEGER
  alarmConfTarget INTEGER
  alarmConfSeverity INTEGER
  alarmConfClearable INTEGER

AlarmCurrEntry  
SEQUENCE    
  alarmCurrIndex INTEGER
  alarmCurrOccurTime TimeTicks
  alarmCurrTrapOid OBJECT IDENTIFIER
  alarmCurrParam1 INTEGER
  alarmCurrParam2 INTEGER
  alarmCurrParam3 INTEGER
  alarmCurrParam4 INTEGER
  alarmCurrParam5 INTEGER
  alarmCurrParam6 INTEGER
  alarmCurrParam7 INTEGER
  alarmCurrParam8 INTEGER
  alarmCurrTimeDescr DisplayString
  alarmCurrSeverity INTEGER
  alarmCurrDescr DisplayString

AlarmSeverityPortEntry  
SEQUENCE    
  severityThresh INTEGER

ExternalAlarmEntry  
SEQUENCE    
  externalAlarmIndex INTEGER
  externalAlarmName DisplayString

AlarmHisEntry  
SEQUENCE    
  alarmHisIndex INTEGER
  alarmHisOccurTime TimeTicks
  alarmHisTrapOid OBJECT IDENTIFIER
  alarmHisParam1 INTEGER
  alarmHisParam2 INTEGER
  alarmHisParam3 INTEGER
  alarmHisParam4 INTEGER
  alarmHisParam5 INTEGER
  alarmHisParam6 INTEGER
  alarmHisParam7 INTEGER
  alarmHisParam8 INTEGER
  alarmHisTimeDescr DisplayString
  alarmHisSeverity INTEGER
  alarmHisDescr DisplayString

MltRelayEntry  
SEQUENCE    
  mltRelaySet INTEGER
  mltRelayTimeout INTEGER
  mltRelayForce INTEGER

Xdsl2ExtSCStatusEntry  
SEQUENCE    
  xdsl2SCStatusActAtp Integer32

Xdsl2ExtSCStatusBandEntry  
SEQUENCE    
  xdsl2SCStatusBandSnrMargin Integer32

StaticRouteEntry  
SEQUENCE    
  staticRouteName DisplayString
  staticRouteDest IpAddress
  staticRouteMask IpAddress
  staticRouteGateway IpAddress
  staticRouteMetric INTEGER
  staticRouteRowStatus RowStatus

ChassisEntry  
SEQUENCE    
  chassisId INTEGER
  chassisFrameNumber INTEGER
  chassisSerialNumber DisplayString
  chassisNumber INTEGER
  chassisStatus INTEGER

SlotEntry  
SEQUENCE    
  slotId INTEGER
  slotModuleType INTEGER
  slotModuleDescr DisplayString
  slotModuleFWVersion DisplayString
  slotModuleDriverVersion DisplayString
  slotModuleModemCodeVersion DisplayString
  slotModuleStatus INTEGER
  slotModuleAlarmStatus INTEGER
  slotModuleSerialNumber DisplayString
  slotModuleHWVersion DisplayString
  slotModuleUpTime INTEGER
  slotModuleMacAddress MacAddress
  slotModuleMacAddress2 MacAddress

MscPortEntry  
SEQUENCE    
  mscPortId INTEGER
  mscPortType INTEGER

IgmpHistoryEntry  
SEQUENCE    
  igmphistoryenable INTEGER

McastGroupEntry  
SEQUENCE    
  mcastGroupIp IpAddress
  mcastGroupFixedPorts PortList
  mcastGroupForbiddenPorts PortList
  mcastGroupRowStatus RowStatus

MacMcastGroupEntry  
SEQUENCE    
  macMcastGroupMac PhysAddress
  macMcastGroupFixedPorts PortList
  macMcastGroupRowStatus RowStatus

McastInetGroupEntry  
SEQUENCE    
  mcastGroupInetAddrType InetAddressType
  mcastGroupInetAddr InetAddress
  mcastGroupInetFixedPorts PortList
  mcastGroupInetForbiddenPorts PortList
  mcastGroupInetRowStatus RowStatus

IgmpFilterEntry  
SEQUENCE    
  igmpFilterName DisplayString
  igmpFilterIndex INTEGER
  igmpFilterStartIp IpAddress
  igmpFilterEndIp IpAddress
  igmpFilterRowStatus RowStatus
  igmpFilterInetAddrType InetAddressType
  igmpFilterInetAddrStart InetAddress
  igmpFilterInetAddrEnd InetAddress

IgmpFilterPortEntry  
SEQUENCE    
  igmpFilterPortFilterName DisplayString

McastBwEntry  
SEQUENCE    
  mcastBwIndex INTEGER
  mcastBwStartIp IpAddress
  mcastBwEndIp IpAddress
  mcastBwBandwidth INTEGER
  mcastBwRowStatus RowStatus

McastBwPortEntry  
SEQUENCE    
  mcastBwPortEnable INTEGER
  mcastBwPortBandwidth INTEGER

McastBwInetEntry  
SEQUENCE    
  mcastBwInetIndex INTEGER
  mcastBwInetAddrType InetAddressType
  mcastBwInetAddrStart InetAddress
  mcastBwInetAddrEnd InetAddress
  mcastBwInetBandwidth INTEGER
  mcastBwInetRowStatus RowStatus

IgmpCountPortEntry  
SEQUENCE    
  igmpCountPortEnable INTEGER
  igmpCountPortLimit INTEGER

IgmpMessageCountPortEntry  
SEQUENCE    
  igmpMessageCountPortEnable INTEGER
  igmpMessageCountPortLimit INTEGER

MvlanEntry  
SEQUENCE    
  mvlanIndex VlanIndex
  mvlanName DisplayString
  mvlanEgressPorts PortList
  mvlanRowStatus RowStatus
  mvlan8021pPriority INTEGER

MvlanTranslateEntry  
SEQUENCE    
  mvlanTranslateIndex INTEGER
  mvlanTranslateStartIp IpAddress
  mvlanTranslateEndIp IpAddress
  mvlanTranslateInetAddrType InetAddressType
  mvlanTranslateInetAddrStart InetAddress
  mvlanTranslateInetAddrEnd InetAddress

MvlanExtEntry  
SEQUENCE    
  mvlanExtReg INTEGER
  mvlanExtCvid INTEGER

QryVidConfEntry  
SEQUENCE    
  qryVid INTEGER
  qryVidRowStatus RowStatus

QryVidStatusEntry  
SEQUENCE    
  qryVidType INTEGER

SubrPortEntry  
SEQUENCE    
  subrPortName DisplayString
  subrPortTel DisplayString
  subrPortMdf DisplayString

AdslLineConfEntry  
SEQUENCE    
  adslLineConfAdslMode INTEGER
  adslLineConfAnnexL INTEGER
  adslLineConfAnnexM INTEGER
  adslLineConfAnnexI INTEGER
  adslLineConfOptionMask INTEGER
  adslLineConfPowerMgmt INTEGER
  adslLineConfPowerMode INTEGER
  adslLineConfAturMaxTxPower INTEGER
  adslLineConfAtucMaxTxPower INTEGER
  adslLineConfMaxRxPower INTEGER
  adslLineConfAturCarrierMask OCTET STRING
  adslLineConfAtucCarrierMask0 OCTET STRING
  adslLineConfAtucCarrierMask1 OCTET STRING
  adslLineConfAturInp INTEGER
  adslLineConfAtucInp INTEGER

BitLoadEntry  
SEQUENCE    
  bitLoadBits OCTET STRING
  bitLoadAtucNumOfCarriers INTEGER
  bitLoadAturNumOfCarriers INTEGER

AdslLineStatusEntry  
SEQUENCE    
  adslLineStatusMode INTEGER
  adslLineStatusUpTime Unsigned32
  adslLineStatusAturInp INTEGER
  adslLineStatusAtucInp INTEGER

PowerMgmtParamEntry  
SEQUENCE    
  powerMgmtL0Time INTEGER
  powerMgmtL2Time INTEGER
  powerMgmtL2Atpr INTEGER
  powerMgmtL2Atprt INTEGER
  powerMgmtL2MinRate INTEGER
  powerMgmtL2MaxRate INTEGER
  powerMgmtL2ThreshRate INTEGER

PowerMgmtPSDEntry  
SEQUENCE    
  powerMgmtAtucMaxPSD INTEGER
  powerMgmtAturMaxPSD INTEGER

ShdslLineConfEntry  
SEQUENCE    
  shdslLineConfShdslMode INTEGER
  shdslLineConfPmms INTEGER
  shdslLineConfPboMode INTEGER
  shdslLineConfPboValue INTEGER
  shdslLineConfModulation INTEGER
  shdslLineConfTCMode INTEGER

ShdslLineStatusEntry  
SEQUENCE    
  shdslLineStatusWirePair INTEGER

PvcEntry  
SEQUENCE    
  pvcVpi INTEGER
  pvcVci INTEGER
  pvcPvid VlanIndex
  pvcEncap INTEGER
  pvcPriority INTEGER
  pvcProfile DisplayString
  pvcRowStatus RowStatus
  pvcMvlanEnable INTEGER
  pvcAcName DisplayString
  pvcServiceName DisplayString
  pvcHelloTime INTEGER

PvcVlanEntry  
SEQUENCE    
  pvcVlanReg INTEGER
  pvcVlanTag INTEGER
  pvcVlanRowStatus RowStatus

PvcUsRateLimitEntry  
SEQUENCE    
  pvcUsRateLimitEnable INTEGER
  pvcUsRateLimit INTEGER

PpvcEntry  
SEQUENCE    
  ppvcVpi INTEGER
  ppvcVci INTEGER
  ppvcPvid VlanIndex
  ppvcEncap INTEGER
  ppvcPriority INTEGER
  ppvcRowStatus RowStatus

PpvcVlanEntry  
SEQUENCE    
  ppvcVlanReg INTEGER
  ppvcVlanTag INTEGER
  ppvcVlanRowStatus RowStatus

PpvcMemberEntry  
SEQUENCE    
  ppvcMemberVpi INTEGER
  ppvcMemberVci INTEGER
  ppvcMemberPriority INTEGER
  ppvcMemberProfile DisplayString
  ppvcMemberRowStatus RowStatus

PvcStatsEntry  
SEQUENCE    
  pvcStatsTxRate Unsigned32
  pvcStatsRxRate Unsigned32
  pvcStatsTxCells Counter64
  pvcStatsRxCells Counter64
  pvcStatsCrcErrors Counter64
  pvcStatsTxPackets Counter64
  pvcStatsRxPackets Counter64
  pvcStatsTxUnicast Counter64
  pvcStatsRxUnicast Counter64
  pvcStatsTxMulticast Counter64
  pvcStatsRxMulticast Counter64
  pvcStatsTxBroadcast Counter64
  pvcStatsRxBroadcast Counter64
  pvcStatsTxDiscard Counter64
  pvcStatsRxDiscard Counter64

PaepvcEntry  
SEQUENCE    
  paepvcVpi INTEGER
  paepvcVci INTEGER
  paepvcPvid VlanIndex
  paepvcEncap INTEGER
  paepvcPriority INTEGER
  paepvcProfile DisplayString
  paepvcAcName DisplayString
  paepvcServiceName DisplayString
  paepvcHelloTime INTEGER
  paepvcRowStatus RowStatus

TlspvcEntry  
SEQUENCE    
  tlspvcVpi INTEGER
  tlspvcVci INTEGER
  tlspvcSvid VlanIndex
  tlspvcEncap INTEGER
  tlspvcSpriority INTEGER
  tlspvcProfile DisplayString
  tlspvcRowStatus RowStatus

VdslLineConfEntry  
SEQUENCE    
  vdslLineConfUpbo INTEGER
  vdslLineConfVdslProfile INTEGER
  vdslLineConfFrequencyPlan INTEGER
  vdslLineConfRfiBand INTEGER
  vdslLineConfIpqosProfile DisplayString
  vdslLineConfVturInp INTEGER
  vdslLineConfVtucInp INTEGER
  vdslLineConfOptionMask INTEGER
  vdslLineConfUpboForceLength INTEGER
  vdslLineConfPsdShape INTEGER
  vdslLineConfDpbo INTEGER
  vdslLineConfDpboParamEsel INTEGER
  vdslLineConfDpboParamEscma INTEGER
  vdslLineConfDpboParamEscmb INTEGER
  vdslLineConfDpboParamEscmc INTEGER
  vdslLineConfDpboParamMus INTEGER
  vdslLineConfDpboParamFmin INTEGER
  vdslLineConfDpboParamFmax INTEGER
  vdslLineConfDpboParamPsdId INTEGER
  vdslLineConfCompatible INTEGER
  vdslLineConfPowerMode INTEGER
  vdslLineConfVturMaxTxPower INTEGER
  vdslLineConfVtucMaxTxPower INTEGER
  vdslLineConfMaxRxPower INTEGER
  vdslLineConfPMask INTEGER
  vdslLineConfAturCarrierMask OCTET STRING
  vdslLineConfAtucCarrierMask0 OCTET STRING
  vdslLineConfAtucCarrierMask1 OCTET STRING
  vdslLineConfSnrModeDs INTEGER
  vdslLineConfSnrModeUs INTEGER
  vdslLineConfTxRefVnDs OCTET STRING
  vdslLineConfTxRefVnUs OCTET STRING
  vdslLineConfTpstcTypeAdsl INTEGER
  vdslLineConfTpstcTypeVdsl INTEGER
  vdslLineConfVturInmEq Unsigned32
  vdslLineConfVtucInmEq Unsigned32
  vdslLineConfInmVturCC Unsigned32
  vdslLineConfInmVtucCC Unsigned32
  vdslLineConfInmVturIATO Unsigned32
  vdslLineConfInmVtucIATO Unsigned32
  vdslLineConfInmVturIATS Unsigned32
  vdslLineConfInmVtucIATS Unsigned32
  vdslLineConfInmVtucISDBUS INTEGER
  vdslLineConfGinpRtxModeDs Xdsl2ConfigRtxMode
  vdslLineConfGinpRtxModeUs Xdsl2ConfigRtxMode
  vdslLineConfGinpEtrMaxDs Unsigned32
  vdslLineConfGinpEtrMaxUs Unsigned32
  vdslLineConfGinpEtrMinDs Unsigned32
  vdslLineConfGinpEtrMinUs Unsigned32
  vdslLineConfGinpNdrMaxDs Unsigned32
  vdslLineConfGinpNdrMaxUs Unsigned32
  vdslLineConfGinpShineRatioDs Unsigned32
  vdslLineConfGinpShineRatioUs Unsigned32
  vdslLineConfGinpLeftrThresholdDs Unsigned32
  vdslLineConfGinpLeftrThresholdUs Unsigned32
  vdslLineConfGinpMaxDelayDs Unsigned32
  vdslLineConfGinpMaxDelayUs Unsigned32
  vdslLineConfGinpMinDelayDs Unsigned32
  vdslLineConfGinpMinDelayUs Unsigned32
  vdslLineConfGinpInpMinDs Unsigned32
  vdslLineConfGinpInpMinUs Unsigned32
  vdslLineConfGinpReinCfgInpDs Unsigned32
  vdslLineConfGinpReinCfgInpUs Unsigned32
  vdslLineConfGinpReinCfgFreqDs Unsigned32
  vdslLineConfGinpReinCfgFreqUs Unsigned32
  vdslLineConfSosMinRateB0Ds Unsigned32
  vdslLineConfSosMinRateB0Us Unsigned32
  vdslLineConfSosTimeDs Unsigned32
  vdslLineConfSosTimeUs Unsigned32
  vdslLineConfSosCrcDs Unsigned32
  vdslLineConfSosCrcUs Unsigned32
  vdslLineConfSosNToneDs Unsigned32
  vdslLineConfSosNToneUs Unsigned32
  vdslLineConfSosMaxDs Unsigned32
  vdslLineConfSosMaxUs Unsigned32
  vdslLineConfSosMultiStepDs BITS
  vdslLineConfSosMultiStepUs BITS
  vdslLineConfRocEnableDs INTEGER
  vdslLineConfRocEnableUs INTEGER
  vdslLineConfRocSnrmDs Unsigned32
  vdslLineConfRocSnrmUs Unsigned32
  vdslLineConfRocMinInpDs Unsigned32
  vdslLineConfRocMinInpUs Unsigned32
  vdslLineConfSosEnableDs INTEGER
  vdslLineConfSosEnableUs INTEGER
  vdslLineConfDynamicDepthDs INTEGER
  vdslLineConfDynamicDepthUs INTEGER
  vdslLineConfDpboParamType INTEGER
  vdslLineConfDpboParamEselMin INTEGER
  vdslLineConfHsTxA43Psd INTEGER
  vdslLineConfHsTxB43Psd INTEGER
  vdslLineConfHsTxA43cB43cPsd INTEGER
  vdslLineConfHsTxV43Carrier257Psd INTEGER
  vdslLineConfHsTxV43Carrier383Psd INTEGER
  vdslLineConfHsTxV43Carrier511Psd INTEGER

VdslPortConfEntry  
SEQUENCE    
  vdslPortConfPvid VlanIndex
  vdslPortConfPriority INTEGER
  vdslPortConfAcceptableFrameType INTEGER
  vdslPortConfTlsEnable INTEGER
  vdslPortConfTlsVid VlanIndex
  vdslPortConfTlsPriority INTEGER
  vdslPortConfDtEnable INTEGER
  vdslPortConfDtSvid VlanIndex
  vdslPortConfDtSpriority INTEGER
  vdslPortConfDtCvid VlanIndex
  vdslPortConfDtCpriority INTEGER
  vdslPortConfTlsPrioCopyEnable INTEGER

VdslPortVlanEntry  
SEQUENCE    
  vdslPortVlanReg INTEGER
  vdslPortVlanTag INTEGER
  vdslPortVlanRowStatus RowStatus

VdslVlanStaticEntry  
SEQUENCE    
  vdslVlanStaticEgressPorts PortList
  vdslVlanStaticUntaggedPorts PortList
  vdslVlanStaticRowStatus RowStatus

VdslPortPvlanEntry  
SEQUENCE    
  vdslPortPvlanEtype Unsigned32
  vdslPortPvlanVid VlanIndex
  vdslPortPvlanPriority INTEGER
  vdslPortPvlanRowStatus RowStatus

VdslRfiCustomEntry  
SEQUENCE    
  vdslRfiCustomIndex INTEGER
  vdslRfiCustomStartFreq INTEGER
  vdslRfiCustomEndFreq INTEGER
  vdslRfiCustomEnable INTEGER
  vdslRfiCustomMode INTEGER

VdslLineConfUpboParamEntry  
SEQUENCE    
  vdslLineConfUpboParamBand INTEGER
  vdslLineConfUpboParamA INTEGER
  vdslLineConfUpboParamB INTEGER

VdslLineConfDpboEntry  
SEQUENCE    
  vdslLineConfDpboIndex INTEGER
  vdslLineConfDpboTone INTEGER
  vdslLineConfDpboPsd INTEGER

IpbpvcDomainEntry  
SEQUENCE    
  ipbpvcDomainName DisplayString
  ipbpvcDomainRowStatus RowStatus

IpbpvcDomainVlanEntry  
SEQUENCE    
  ipbpvcDomainVlanId VlanIndex
  ipbpvcDomainDhcpVlanEnable INTEGER
  ipbpvcDomainVlanRowStatus RowStatus

IpbpvcEdgeRouterEntry  
SEQUENCE    
  ipbpvcEdgeRouterIp IpAddress
  ipbpvcEdgeRouterMask INTEGER
  ipbpvcEdgeRouterVid VlanIndex
  ipbpvcEdgeRouterRowStatus RowStatus

IpbpvcInterfaceEntry  
SEQUENCE    
  ipbpvcInterfaceIp IpAddress
  ipbpvcInterfaceMask INTEGER
  ipbpvcInterfaceVid VlanIndex
  ipbpvcInterfaceIfIndex INTEGER
  ipbpvcInterfaceVpi INTEGER
  ipbpvcInterfaceVci INTEGER
  ipbpvcInterfaceRowStatus RowStatus

IpbpvcRouteEntry  
SEQUENCE    
  ipbpvcRouteIp IpAddress
  ipbpvcRouteMask INTEGER
  ipbpvcRouteNextHop IpAddress
  ipbpvcRouteMetric INTEGER
  ipbpvcRoutePriority INTEGER
  ipbpvcRouteRowStatus RowStatus

IpbpvcEntry  
SEQUENCE    
  ipbpvcVpi INTEGER
  ipbpvcVci INTEGER
  ipbpvcPvid INTEGER
  ipbpvcEncap INTEGER
  ipbpvcPriority INTEGER
  ipbpvcProfile DisplayString
  ipbpvcRowStatus RowStatus

IpbpvcVlanEntry  
SEQUENCE    
  ipbpvcVlanReg INTEGER
  ipbpvcVlanTag INTEGER
  ipbpvcVlanRowStatus RowStatus

VoipSipLineConfEntry  
SEQUENCE    
  voipSipLineConfSipProfile DisplayString
  voipSipLineConfSipCallSvcProfile DisplayString
  voipSipLineConfDspProfile DisplayString
  voipSipLineConfAccount DisplayString
  voipSipLineConfPassword DisplayString
  voipSipLineConfDataProfile DisplayString

VoipH248LineConfEntry  
SEQUENCE    
  voipH248LineConfMgName DisplayString
  voipH248LineConfDspProfile DisplayString
  voipH248LineConfDataProfile DisplayString

VoipH248TerminationEntry  
SEQUENCE    
  voipH248TerminationName DisplayString

VoipPotsImpedanceConfEntry  
SEQUENCE    
  voipPotsImpedance INTEGER

VoipPotsGainConfEntry  
SEQUENCE    
  voipPotsTxGain INTEGER
  voipPotsRxGain INTEGER
  voipPotsDataTxGain INTEGER
  voipPotsDataRxGain INTEGER

VoipOpmodeConfEntry  
SEQUENCE    
  voipOpMode INTEGER

VoipPolarityReverseConfEntry  
SEQUENCE    
  voipPolarityReverse INTEGER

VoipPotsCidConfEntry  
SEQUENCE    
  voipPotsCidASType INTEGER
  voipPotsCidPayloadType INTEGER

VoipPotsLineConfEntry  
SEQUENCE    
  voipPotsLineFlashDefault INTEGER
  voipPotsLineFlashMax INTEGER
  voipPotsLineFlashMin INTEGER
  voipPotsLineLoop INTEGER

EnetLineConfEntry  
SEQUENCE    
  enetLineConfBandWidthIngress INTEGER
  enetLineConfBandWidthEgress INTEGER
  enetLineConfFlowCtrlEnable INTEGER
  enetLineConfSpeed INTEGER

EnetPortConfEntry  
SEQUENCE    
  enetPortConfPriority INTEGER
  enetPortConfPvid VlanIndex
  enetPortConfAcceptableFrameType INTEGER
  enetPortConfTlsEnable INTEGER
  enetPortConfTlsVid VlanIndex
  enetPortConfTlsPriority INTEGER
  enetPortConfRateLimitProfile DisplayString
  enetPortConfQueueRateLimitProfile DisplayString
  enetPortConfDtEnable INTEGER
  enetPortConfDtSvid VlanIndex
  enetPortConfDtSpriority INTEGER
  enetPortConfDtCvid VlanIndex

EnetPortVlanEntry  
SEQUENCE    
  enetPortVlanReg INTEGER
  enetPortVlanTag INTEGER
  enetPortVlanRowStatus RowStatus

ElcDot3adEntry  
SEQUENCE    
  elcDot3adSlotId INTEGER
  elcDot3adGroupId INTEGER
  elcDot3adEnable INTEGER

ElcAggPortEntry  
SEQUENCE    
  elcAggPortJoin INTEGER

EnetQScheduleEntry  
SEQUENCE    
  enetQScheduleType INTEGER

EnetQueueWeightEntry  
SEQUENCE    
  enetQueueWeight INTEGER

EnetPortPvlanEntry  
SEQUENCE    
  enetPortPvlanEtype Unsigned32
  enetPortPvlanVid VlanIndex
  enetPortPvlanPriority INTEGER
  enetPortPvlanRowStatus RowStatus

EnetPortXvlanEntry  
SEQUENCE    
  enetPortXvlanCvid Unsigned32
  enetPortXvlanSvid Unsigned32
  enetPortXvlanRowStatus RowStatus

GbondGroupEntry  
SEQUENCE    
  gbondGroupName DisplayString
  gbondGroupPorts OCTET STRING
  gbondGroupRowStatus RowStatus

DtpvcEntry  
SEQUENCE    
  dtpvcVpi INTEGER
  dtpvcVci INTEGER
  dtpvcSvid VlanIndex
  dtpvcCvid VlanIndex
  dtpvcEncap INTEGER
  dtpvcSPriority INTEGER
  dtpvcCPriority INTEGER
  dtpvcProfile DisplayString
  dtpvcRowStatus RowStatus
  dtpvcMvlanEnable INTEGER

E1PortConfEntry  
SEQUENCE    
  e1PortConfAdminStatus INTEGER
  e1PortConfAlarmProfile DisplayString
  e1PortConfImpedance INTEGER
  e1PortConfTimingSrc INTEGER

XvlanEntry  
SEQUENCE    
  xvlanCvid Unsigned32
  xvlanSvid Unsigned32
  xvlanCvids Unsigned32
  xvlanRowStatus RowStatus

Vdsl2LineConfEntry  
SEQUENCE    
  vdsl2LineConfRateLimitProfile DisplayString
  vdsl2LineConfQueueRateLimitProfile DisplayString

Vdsl2PvcEntry  
SEQUENCE    
  vdsl2PvcVpi INTEGER
  vdsl2PvcVci INTEGER
  vdsl2PvcPvid INTEGER
  vdsl2PvcEncap INTEGER
  vdsl2PvcPriority INTEGER
  vdsl2PvcSuper INTEGER
  vdsl2PvcRowStatus RowStatus

Vdsl2QSchedulePortEntry  
SEQUENCE    
  vdsl2QScheduleType INTEGER

Vdsl2QueueWeightEntry  
SEQUENCE    
  vdsl2QueueWeight INTEGER

PvcAllEntry  
SEQUENCE    
  pvcAllVpi INTEGER
  pvcAllVci INTEGER
  pvcAllEncap INTEGER
  pvcAllType INTEGER

Vdsl2PaepvcEntry  
SEQUENCE    
  vdsl2PaepvcVpi INTEGER
  vdsl2PaepvcVci INTEGER
  vdsl2PaepvcPvid VlanIndex
  vdsl2PaepvcEncap INTEGER
  vdsl2PaepvcPriority INTEGER
  vdsl2PaepvcAcName DisplayString
  vdsl2PaepvcServiceName DisplayString
  vdsl2PaepvcHelloTime INTEGER
  vdsl2PaepvcRowStatus RowStatus

AtmProfileEntry  
SEQUENCE    
  atmProfileName DisplayString
  atmProfileAAL INTEGER
  atmProfileClass INTEGER
  atmProfilePcr Unsigned32
  atmProfileCdvt INTEGER
  atmProfileScrMcr Unsigned32
  atmProfileBt INTEGER
  atmProfileRowStatus RowStatus

ProfsvrClientEntry  
SEQUENCE    
  profsvrClientIp IpAddress
  profsvrClientType INTEGER
  profsvrClientRowStatus RowStatus

AclProfileEntry  
SEQUENCE    
  aclProfileRuleName DisplayString
  aclProfileRuleNumber INTEGER
  aclProfileActionNumber INTEGER
  aclProfileRuleParamMask INTEGER
  aclProfileRuleEtype INTEGER
  aclProfileRuleVid INTEGER
  aclProfileRuleSmac PhysAddress
  aclProfileRuleDmac PhysAddress
  aclProfileRulePriority INTEGER
  aclProfileRuleProtocol INTEGER
  aclProfileRuleSrcIP IpAddress
  aclProfileRuleSrcIPMask INTEGER
  aclProfileRuleDestIP IpAddress
  aclProfileRuleDestIPMask INTEGER
  aclProfileRuleStartTos INTEGER
  aclProfileRuleEndTos INTEGER
  aclProfileRuleSrcStartPort INTEGER
  aclProfileRuleSrcEndPort INTEGER
  aclProfileRuleDestStartPort INTEGER
  aclProfileRuleDestEndPort INTEGER
  aclProfileActionRate INTEGER
  aclProfileActionrvlan INTEGER
  aclProfileActionrpri INTEGER
  aclProfileRowStatus RowStatus
  aclProfileRuleSip IpAddress
  aclProfileRuleDip IpAddress
  aclProfileRuleSport INTEGER
  aclProfileRuleDport INTEGER
  aclProfileRuleSrcIp6 InetAddress
  aclProfileRuleDstIp6 InetAddress
  aclProfileRuleSip6 InetAddress
  aclProfileRuleDip6 InetAddress

VdslLineConfProfileExtendedEntry  
SEQUENCE    
  vdsl2LConfProfRaModeDs INTEGER
  vdsl2LConfProfRaModeUs INTEGER
  vdsl2LConfProfRaUsNrmDs Unsigned32
  vdsl2LConfProfRaUsNrmUs Unsigned32
  vdsl2LConfProfRaDsNrmDs Unsigned32
  vdsl2LConfProfRaDsNrmUs Unsigned32
  vdsl2LConfProfProfileName DisplayString

VdslLineAlarmConfProfileExtendedEntry  
SEQUENCE    
  vdslLAlarmConfProfProfileName DisplayString

SipProfileEntry  
SEQUENCE    
  sipProfileName DisplayString
  sipProfileSipSvr DisplayString
  sipProfileRegSvr DisplayString
  sipProfileProxySvr DisplayString
  sipProfileSipPort INTEGER
  sipProfileRegSvrPort INTEGER
  sipProfileProxySvrPort INTEGER
  sipProfileUriType INTEGER
  sipProfilePbit INTEGER
  sipProfileDscp INTEGER
  sipProfileKeepAlive INTEGER
  sipProfileSe INTEGER
  sipProfilePrack INTEGER
  sipProfileRowStatus RowStatus
  sipProfileReSend INTEGER
  sipProfileNonceCountKeep INTEGER
  sipProfileQopQuote INTEGER
  sipProfileRefertobracket INTEGER
  sipProfileRefertodot INTEGER
  sipProfileRtpStartPort INTEGER
  sipProfileRtpEndPort INTEGER

SipCallSvcProfileEntry  
SEQUENCE    
  sipCallSvcProfileName DisplayString
  sipCallSvcProfilePasswdOn INTEGER
  sipCallSvcProfilePasswd DisplayString
  sipCallSvcProfileNumberPlanOn INTEGER
  sipCallSvcProfileNumberPlanCc DisplayString
  sipCallSvcProfileNumberPlanNdc DisplayString
  sipCallSvcProfileNumberPlanTable DisplayString
  sipCallSvcProfileStateMask INTEGER
  sipCallSvcProfileDtmf INTEGER
  sipCallSvcProfileFax INTEGER
  sipCallSvcProfileRowStatus RowStatus
  sipCallSvcProfileKeypattern DisplayString
  sipCallSvcProfileRegTime INTEGER
  sipCallSvcProfileFlash INTEGER
  sipCallSvcProfileFlashPattern DisplayString
  sipCallSvcProfileReanswerTime INTEGER
  sipCallSvcProfileFirstDigit INTEGER
  sipCallSvcProfileInterdigit INTEGER

SipCallSvcProfileLocalHelpEntry  
SEQUENCE    
  sipCallSvcProfileLocalHelpIndex INTEGER
  sipCallSvcProfileLocalHelpTableName DisplayString
  sipCallSvcProfileLocalHelpTableTel DisplayString

SipDialPlanProfileEntry  
SEQUENCE    
  sipDialPlanProfileName DisplayString
  sipDialPlanProfileIndex INTEGER
  sipDialPlanProfileDialPlanTableName DisplayString
  sipDialPlanProfileRowStatus RowStatus

H248ProfileEntry  
SEQUENCE    
  h248ProfileName DisplayString
  h248ProfileMgc DisplayString
  h248ProfileMgcPort INTEGER
  h248ProfileMgc2On INTEGER
  h248ProfileMgc2 DisplayString
  h248ProfileMgc2Port INTEGER
  h248ProfileTransport INTEGER
  h248ProfileEncode INTEGER
  h248ProfilePbit INTEGER
  h248ProfileDscp INTEGER
  h248ProfileRowStatus RowStatus
  h248ProfileSoftswitch INTEGER
  h248ProfileInactivityTimer INTEGER
  h248ProfilePrefixName DisplayString
  h248ProfileRtpPortStart INTEGER
  h248ProfileRtpPortEnd INTEGER
  h248ProfileInitRetranTime INTEGER
  h248ProfileMinRetranTime INTEGER
  h248ProfileMaxRetranTime INTEGER
  h248ProfileRetranWindow INTEGER
  h248ProfileStartTimeout INTEGER
  h248ProfileShortTimeout INTEGER
  h248ProfileLongTimeout INTEGER
  h248ProfileVBD INTEGER
  h248ProfileSuffixStartNum DisplayString
  h248ProfileSuffixSuffixLen INTEGER
  h248ProfileRFC2833 INTEGER
  h248ProfileRFC2833PT INTEGER
  h248ProfileT38 INTEGER
  h248ProfileForceVersion INTEGER
  h248ProfileLocalcall INTEGER
  h248ProfileCallthrough INTEGER

DspProfileEntry  
SEQUENCE    
  dspProfileName DisplayString
  dspProfileCodec INTEGER
  dspProfilePlayBufferMinDelay INTEGER
  dspProfilePlayBufferMaxDelay INTEGER
  dspProfileEchoTail INTEGER
  dspProfileRowStatus RowStatus
  dspProfileEchocancelOn INTEGER
  dspProfileVadOn INTEGER
  dspProfileg711vpi INTEGER
  dspProfileg723vpi INTEGER
  dspProfileg726vpi INTEGER
  dspProfileg729vpi INTEGER
  dspProfilePbit INTEGER
  dspProfileDscp INTEGER
  dspProfileCodecPriority DisplayString

IpqosProfileEntry  
SEQUENCE    
  ipqosProfileName DisplayString
  ipqosProfileNumOfQueue INTEGER
  ipqosProfileRowStatus RowStatus

IpqosProfileQueueEntry  
SEQUENCE    
  ipqosProfileQueueIndex INTEGER
  ipqosProfileQueuePIR INTEGER
  ipqosProfileQueueCIR INTEGER
  ipqosProfileQueuePBS INTEGER
  ipqosProfileQueueCBS INTEGER
  ipqosProfileQueueLevel INTEGER
  ipqosProfileQueueWeight INTEGER

RateLimitProfileEntry  
SEQUENCE    
  rateLimitProfileName DisplayString
  rateLimitProfileIngressRate INTEGER
  rateLimitProfileEgressRate INTEGER
  rateLimitProfileRowStatus RowStatus

E1AlarmProfileEntry  
SEQUENCE    
  e1AlarmProfileName DisplayString
  e1AlarmProfileQEs INTEGER
  e1AlarmProfileQSes INTEGER
  e1AlarmProfileQUas INTEGER
  e1AlarmProfileDayEs INTEGER
  e1AlarmProfileDaySes INTEGER
  e1AlarmProfileDayUas INTEGER
  e1AlarmProfileRowStatus RowStatus

Vdsl2LineConfProfileExtendedEntry  
SEQUENCE    
  vdsl2LineProfDpboEPsdID INTEGER
  vdsl2LineProfBitSwapDs INTEGER
  vdsl2LineProfBitSwapUs INTEGER
  vdsl2LineProfProfileName DisplayString
  vdsl2LineProfDynamicDepthEnableDs INTEGER
  vdsl2LineProfDynamicDepthEnableUs INTEGER
  vdsl2LineProfSosTimeDs Unsigned32
  vdsl2LineProfSosTimeUs Unsigned32
  vdsl2LineProfSosCrcDs Unsigned32
  vdsl2LineProfSosCrcUs Unsigned32
  vdsl2LineProfSosNToneDs Unsigned32
  vdsl2LineProfSosNToneUs Unsigned32
  vdsl2LineProfSosMaxDs Unsigned32
  vdsl2LineProfSosMaxUs Unsigned32
  vdsl2LineProfSosMultiStepDs BITS
  vdsl2LineProfSosMultiStepUs BITS
  vdsl2LineProfRocEnableDs INTEGER
  vdsl2LineProfRocEnableUs INTEGER
  vdsl2LineProfRocSnrmDs Unsigned32
  vdsl2LineProfRocSnrmUs Unsigned32
  vdsl2LineProfRocMinInpDs Unsigned32
  vdsl2LineProfRocMinInpUs Unsigned32
  vdsl2LineProfDpboType INTEGER
  vdsl2LineProfDpboEselMin INTEGER
  vdsl2LineProfCompatible INTEGER
  vdsl2LineProfTransmissionType BITS

Vdsl2ChanConfProfileExtendedEntry  
SEQUENCE    
  vdsl2ChanConfProfphyRds INTEGER
  vdsl2ChanConfProfphyRus INTEGER
  vdsl2ChanConfProfProfileName DisplayString
  vdsl2ChanConfProfGinpRtxModeDs Xdsl2ConfigRtxMode
  vdsl2ChanConfProfGinpRtxModeUs Xdsl2ConfigRtxMode
  vdsl2ChanConfProfGinpEtrMaxDs Unsigned32
  vdsl2ChanConfProfGinpEtrMaxUs Unsigned32
  vdsl2ChanConfProfGinpEtrMinDs Unsigned32
  vdsl2ChanConfProfGinpEtrMinUs Unsigned32
  vdsl2ChanConfProfGinpNdrMaxDs Unsigned32
  vdsl2ChanConfProfGinpNdrMaxUs Unsigned32
  vdsl2ChanConfProfGinpShineRatioDs Unsigned32
  vdsl2ChanConfProfGinpShineRatioUs Unsigned32
  vdsl2ChanConfProfGinpLeftrThresholdDs Unsigned32
  vdsl2ChanConfProfGinpLeftrThresholdUs Unsigned32
  vdsl2ChanConfProfGinpMaxDelayDs Unsigned32
  vdsl2ChanConfProfGinpMaxDelayUs Unsigned32
  vdsl2ChanConfProfGinpMinDelayDs Unsigned32
  vdsl2ChanConfProfGinpMinDelayUs Unsigned32
  vdsl2ChanConfProfGinpInpMinDs Unsigned32
  vdsl2ChanConfProfGinpInpMinUs Unsigned32
  vdsl2ChanConfProfGinpReinCfgInpDs Unsigned32
  vdsl2ChanConfProfGinpReinCfgInpUs Unsigned32
  vdsl2ChanConfProfGinpReinCfgFreqDs Unsigned32
  vdsl2ChanConfProfGinpReinCfgFreqUs Unsigned32
  vdsl2ChanConfProfSosMinRateB0Ds Unsigned32
  vdsl2ChanConfProfSosMinRateB0Us Unsigned32

Vdsl2LineAlarmConfProfileExtendedEntry  
SEQUENCE    
  xdsl2LineAlarmConfProfileXtucThresh15MinLofs Unsigned32
  xdsl2LineAlarmConfProfileXturThresh15MinLofs Unsigned32
  xdsl2LineAlarmConfProfileThresh15MinLprs Unsigned32
  xdsl2LineAlarmConfProfileProfileName DisplayString
  xdsl2LineAlarmConfProfileXtucThresh15MinLols Unsigned32

Vdsl2LineConfTempExtendedEntry  
SEQUENCE    
  vdsl2LineConfTempTemplateName DisplayString
  vdsl2LineConfTempTemplatePortMap PortList
  vdsl2LineConfTempInmProfile DisplayString

Vdsl2AlarmConfTempExtendedEntry  
SEQUENCE    
  vdsl2AlarmConfTempTemplateName DisplayString

Vdsl2ChanAlarmConfProfileExtendedEntry  
SEQUENCE    
  vdsl2ChanAlarmConfProfProfileName DisplayString

Vdsl2InmConfProfileExtendedEntry  
SEQUENCE    
  xdsl2InmConfProfProfileName DisplayString
  xdsl2InmConfProfVtucInpEq Unsigned32
  xdsl2InmConfProfVturInpEq Unsigned32
  xdsl2InmConfProfVtucCC Unsigned32
  xdsl2InmConfProfVturCC Unsigned32
  xdsl2InmConfProfVtucIATO Unsigned32
  xdsl2InmConfProfVturIATO Unsigned32
  xdsl2InmConfProfVtucIATS Unsigned32
  xdsl2InmConfProfVturIATS Unsigned32
  xdsl2InmConfProfRowStatus RowStatus
  xdsl2InmConfProfVtucISDBUS INTEGER

QueueRateLimitProfileEntry  
SEQUENCE    
  queueRateLimitProfileName DisplayString
  queueRateLimitProfileQueue0CIR INTEGER
  queueRateLimitProfileQueue0PIR INTEGER
  queueRateLimitProfileQueue1CIR INTEGER
  queueRateLimitProfileQueue1PIR INTEGER
  queueRateLimitProfileQueue2CIR INTEGER
  queueRateLimitProfileQueue2PIR INTEGER
  queueRateLimitProfileQueue3CIR INTEGER
  queueRateLimitProfileQueue3PIR INTEGER
  queueRateLimitProfileQueue4CIR INTEGER
  queueRateLimitProfileQueue4PIR INTEGER
  queueRateLimitProfileQueue5CIR INTEGER
  queueRateLimitProfileQueue5PIR INTEGER
  queueRateLimitProfileQueue6CIR INTEGER
  queueRateLimitProfileQueue6PIR INTEGER
  queueRateLimitProfileQueue7CIR INTEGER
  queueRateLimitProfileQueue7PIR INTEGER
  queueRateLimitProfileRowStatus RowStatus

Ipqos2ProfileEntry  
SEQUENCE    
  ipqos2ProfileName DisplayString
  ipqos2ProfileAlgorithm INTEGER
  ipqos2ProfileVcLevel INTEGER
  ipqos2ProfileVcMaxRate INTEGER
  ipqos2ProfileVcDepth INTEGER
  ipqos2ProfileQueue0Weight INTEGER
  ipqos2ProfileQueue0MaxRate INTEGER
  ipqos2ProfileQueue0Depth INTEGER
  ipqos2ProfileQueue1Weight INTEGER
  ipqos2ProfileQueue1MaxRate INTEGER
  ipqos2ProfileQueue1Depth INTEGER
  ipqos2ProfileQueue2Weight INTEGER
  ipqos2ProfileQueue2MaxRate INTEGER
  ipqos2ProfileQueue2Depth INTEGER
  ipqos2ProfileQueue3Weight INTEGER
  ipqos2ProfileQueue3MaxRate INTEGER
  ipqos2ProfileQueue3Depth INTEGER
  ipqos2ProfileQueue4Weight INTEGER
  ipqos2ProfileQueue4MaxRate INTEGER
  ipqos2ProfileQueue4Depth INTEGER
  ipqos2ProfileQueue5Weight INTEGER
  ipqos2ProfileQueue5MaxRate INTEGER
  ipqos2ProfileQueue5Depth INTEGER
  ipqos2ProfileQueue6Weight INTEGER
  ipqos2ProfileQueue6MaxRate INTEGER
  ipqos2ProfileQueue6Depth INTEGER
  ipqos2ProfileQueue7Weight INTEGER
  ipqos2ProfileQueue7MaxRate INTEGER
  ipqos2ProfileQueue7Depth INTEGER
  ipqos2ProfileRowStatus RowStatus

EnetPortEntry  
SEQUENCE    
  enetPortSpeed INTEGER
  enetPortFlowControl INTEGER
  enetPortMode INTEGER
  enetPortVLANTrunkEnable INTEGER
  enetPortDscpEnable INTEGER
  enetPortTpid INTEGER

EnetPortSfpEntry  
SEQUENCE    
  sfpTempLow INTEGER
  sfpTempHigh INTEGER
  sfpVccLow INTEGER
  sfpVccHigh INTEGER
  sfpTxBiasLow INTEGER
  sfpTxBiasHigh INTEGER
  sfpTxPowerLow INTEGER
  sfpTxPowerHigh INTEGER
  sfpRxPowerLow INTEGER
  sfpRxPowerHigh INTEGER

BwPortEntry  
SEQUENCE    
  bwPortEnable INTEGER
  bwPortIngressRate INTEGER
  bwPortEgressRate INTEGER

QschedulePortEntry  
SEQUENCE    
  qschedulePortType INTEGER

QueueWeightEntry  
SEQUENCE    
  queueWeight INTEGER

Dot3adEntry  
SEQUENCE    
  dot3adGroupId INTEGER
  dot3adEnable INTEGER
  dot3adGroupName DisplayString
  dot3adGroupPortList PortList

PortTrunkingEntry  
SEQUENCE    
  portTrunkingGroupId INTEGER
  portTrunkingStatus INTEGER
  portTrunkingPortList PortList

AggPortEntry  
SEQUENCE    
  aggPortJoin INTEGER

ElcPortTrunkingEntry  
SEQUENCE    
  elcPortTrunkingSlot INTEGER
  elcPortTrunkingGroupId INTEGER
  elcPortTrunkingStatus INTEGER
  elcPortTrunkingPortList PortList

BctrlPortEntry  
SEQUENCE    
  bctrlPortBcastEnable INTEGER
  bctrlPortMcastEnable INTEGER
  bctrlPortUcastEnable INTEGER
  bctrlPortBcastThresh INTEGER
  bctrlPortMcastThresh INTEGER
  bctrlPortUcastThresh INTEGER

DscpMappingPortEntry  
SEQUENCE    
  dscpMappingPortSrcCodePoint INTEGER
  dscpMappingPortMapCodePoint INTEGER
  dscpMappingPortMapPriority INTEGER

MstpMapEntry  
SEQUENCE    
  mstpMapIndex INTEGER
  mstpMapVlans1k OCTET STRING
  mstpMapVlans2k OCTET STRING
  mstpMapVlans3k OCTET STRING
  mstpMapVlans4k OCTET STRING

MstpVlanEntry  
SEQUENCE    
  mstpVlanIndex VlanIndex
  mstpVlanMstIndex INTEGER

MstpPortEntry  
SEQUENCE    
  mstpPortAdminEdgePort INTEGER
  mstpPortAdminPointToPoint INTEGER

MstpXstEntry  
SEQUENCE    
  mstpXstId INTEGER
  mstpXstBridgePriority INTEGER

MstpXstPortEntry  
SEQUENCE    
  mstpXstPortXstId INTEGER
  mstpXstPortIndex INTEGER
  mstpXstPortEnable INTEGER
  mstpXstPortPriority INTEGER
  mstpXstPortAdminPathCost INTEGER

VlanIsolationEntry  
SEQUENCE    
  vlanIsolationRowStatus INTEGER

CfmLoopbackPortEntry  
SEQUENCE    
  cfmLoopbackPortState INTEGER

CfmMIPEntry  
SEQUENCE    
  cfmLevel INTEGER
  cfmVlanID INTEGER
  cfmPort INTEGER
  cfmMIPRowStatus RowStatus
  cfmMIPMacAddress MacAddress

CfmLbrEntry  
SEQUENCE    
  cfmLbrSeqNumber Unsigned32
  cfmLbrReceiveOrder Unsigned32
  cfmLbrSrcMac MacAddress

RemoteLoopbackEntry  
SEQUENCE    
  remoteLoopbackEnable INTEGER

VlanpriorityEntry  
SEQUENCE    
  vlanpriorityVid INTEGER
  vlanpriorityPri INTEGER
  vlanpriorityRowStatus RowStatus

MirrorPortEntry  
SEQUENCE    
  mirrorPortDirection INTEGER

FanRpmEntry  
SEQUENCE    
  fanRpmIndex INTEGER
  fanRpmCurValue INTEGER
  fanRpmMaxValue INTEGER
  fanRpmMinValue INTEGER
  fanRpmLowThresh INTEGER
  fanRpmDescr DisplayString
  fanRpmHighThresh INTEGER

VoltageEntry  
SEQUENCE    
  voltageIndex INTEGER
  voltageCurValue INTEGER
  voltageMaxValue INTEGER
  voltageMinValue INTEGER
  voltageNominalValue INTEGER
  voltageLowThresh INTEGER
  voltageDescr DisplayString
  voltageHighThresh INTEGER

TemperatureEntry  
SEQUENCE    
  temperatureIndex INTEGER
  temperatureCurValue INTEGER
  temperatureMaxValue INTEGER
  temperatureMinValue INTEGER
  temperatureHighThresh INTEGER
  temperatureDescr DisplayString
  temperatureLowThresh INTEGER

CpuUtilizationEntry  
SEQUENCE    
  cpuIndex INTEGER
  cpuCurValue INTEGER
  cpuMaxValue INTEGER
  cpuHighThresh INTEGER
  cpuDescr DisplayString

PacketBufferUsageEntry  
SEQUENCE    
  packetBufferIndex INTEGER
  packetBufferCurValue INTEGER
  packetBufferMaxValue INTEGER
  packetBufferHighThresh INTEGER
  packetBufferDescr DisplayString

MemoryUsageEntry  
SEQUENCE    
  memoryIndex INTEGER
  memoryCurValue INTEGER
  memoryMaxValue INTEGER
  memoryHighThresh INTEGER
  memoryDescr DisplayString

AccessCtrlEntry  
SEQUENCE    
  accessCtrlService INTEGER
  accessCtrlEnable INTEGER
  accessCtrlPort INTEGER

SecuredClientEntry  
SEQUENCE    
  securedClientIndex INTEGER
  securedClientStartIp IpAddress
  securedClientEndIp IpAddress
  securedClientService INTEGER
  securedClientEnable INTEGER

SecuredClientInetEntry  
SEQUENCE    
  securedClientInetIndex INTEGER
  securedClientInetAddrType InetAddressType
  securedClientInetAddr InetAddress
  securedClientInetMask INTEGER
  securedClientInetService INTEGER
  securedClientInetEnable INTEGER

SyslogEntry  
SEQUENCE    
  syslogFacility INTEGER
  syslogServer IpAddress
  syslogServerInetAddrType InetAddressType
  syslogServerInetAddr InetAddress

TrapDestEntry  
SEQUENCE    
  trapDestIndex INTEGER
  trapDestIp IpAddress
  trapDestPort INTEGER
  trapDestSnmpVersion INTEGER
  trapDestUserName DisplayString
  trapDestInetAddrType InetAddressType
  trapDestInetAddr InetAddress

SnmpUserEntry  
SEQUENCE    
  snmpUserName DisplayString
  snmpUserSecurityLevel INTEGER
  snmpUserAuthProtocol INTEGER
  snmpUserPrivProtocol INTEGER

UserEntry  
SEQUENCE    
  userName DisplayString
  userPassword DisplayString
  userPriviledge INTEGER
  userRowStatus RowStatus

RadiusAuthServerEntry  
SEQUENCE    
  radiusAuthServerIndex INTEGER
  radiusAuthServerIP IpAddress
  radiusAuthServerPort INTEGER
  radiusAuthServerSecret DisplayString

RadiusAcctServerEntry  
SEQUENCE    
  radiusAcctServerIndex INTEGER
  radiusAcctServerIP IpAddress
  radiusAcctServerPort INTEGER
  radiusAcctServerSecret DisplayString

TacacsplusAuthServerEntry  
SEQUENCE    
  tacscsplusAuthServerIndex INTEGER
  tacscsplusAuthServerIP IpAddress
  tacscsplusAuthServerPort INTEGER
  tacscsplusAuthServerSecret DisplayString

TacacsplusAcctServerEntry  
SEQUENCE    
  tacacsplusAcctServerIndex INTEGER
  tacacsplusAcctServerIP IpAddress
  tacacsplusAcctServerPort INTEGER
  tacacsplusAcctServerSecret DisplayString

TacacsplusAuthorServerEntry  
SEQUENCE    
  tacscsplusAuthorServerIndex INTEGER
  tacscsplusAuthorServerIP IpAddress
  tacscsplusAuthorServerPort INTEGER
  tacscsplusAuthorServerSecret DisplayString

AuthorCmdMethodEntry  
SEQUENCE    
  authorCmdMethod INTEGER

DhcpSnoopIpEntry  
SEQUENCE    
  dhcpSnoopIp IpAddress
  dhcpSnoopMac PhysAddress
  dhcpSnoopVid VlanIndex

DhcpSnoopCounterEntry  
SEQUENCE    
  dhcpDiscovery Counter64
  dhcpOffer Counter64
  dhcpRequest Counter64
  dhcpAck Counter64
  dhcpAckBySnoopFull Counter64
  dhcpv6Solicit Counter64
  dhcpv6Advertise Counter64
  dhcpv6Request Counter64
  dhcpv6Reply Counter64
  dhcpv6Renew Counter64
  dhcpv6Rebind Counter64
  dhcpv6Release Counter64
  dhcpv6RelayFwd Counter64
  dhcpv6RelayReply Counter64

Dhcpv6SnoopIpEntry  
SEQUENCE    
  dhcpv6SnoopInetAddrType InetAddressType
  dhcpv6SnoopInetAddr InetAddress
  dhcpv6SnoopMac PhysAddress
  dhcpv6SnoopVid VlanIndex

IgmpGroupEntry  
SEQUENCE    
  igmpGroupVid VlanIndex
  igmpGroupIp IpAddress
  igmpGroupNumOfMembers INTEGER
  igmpGroupMemberPorts PortList

IgmpGroupPortEntry  
SEQUENCE    
  igmpGroupPortVid VlanIndex
  igmpGroupPortIp IpAddress
  igmpGroupPortSourceIp IpAddress

IgmpPortCtrlPduEntry  
SEQUENCE    
  igmpPortCtrlPduQueryCnt Counter32
  igmpPortCtrlPduReportCnt Counter32
  igmpPortCtrlPduLeaveCnt Counter32
  igmpPortNumOfActiveGroups INTEGER
  igmpPortCtrlPduV2SuccessJoinCnt Counter32
  igmpPortCtrlPduV2UnsuccJoinCnt Counter32
  igmpPortCtrlPduGenQryCnt Counter32
  igmpPortCtrlPduSpecQryCnt Counter32
  igmpPortCtrlPduV3SuccessReportCnt Counter32
  igmpPortCtrlPduV3UnsuccReportCnt Counter32
  igmpPortCtrlPduInvalidCnt Counter32

IgmpVlanStatsEntry  
SEQUENCE    
  igmpVlanStatsVlanIndex VlanIndex
  igmpVlanStatsQueryCnt Counter32
  igmpVlanStatsReportCnt Counter32
  igmpVlanStatsLeaveCnt Counter32
  igmpVlanStatsNumOfActiveGroups INTEGER
  igmpVlanStatsQueryPort INTEGER
  igmpVlanStatsQuerierIp IpAddress
  igmpVlanStatsUnsuccessReportCnt Counter32
  igmpVlanStatsSuccessReportCnt Counter32
  igmpVlanStatsGeneralQueryInCnt Counter32
  igmpVlanStatsGeneralQueryOutCnt Counter32
  igmpVlanStatsSpecificQueryInCnt Counter32
  igmpVlanStatsSpecificQueryOutCnt Counter32

MacEntry  
SEQUENCE    
  macAddress MacAddress
  macPort INTEGER
  macStatus INTEGER

AdslLineStatsEntry  
SEQUENCE    
  adslLineStatsAtucHlog1 OCTET STRING
  adslLineStatsAtucHlog2 OCTET STRING
  adslLineStatsAturHlog OCTET STRING
  adslLineStatsAtucQln1 OCTET STRING
  adslLineStatsAtucQln2 OCTET STRING
  adslLineStatsAturQln OCTET STRING
  adslLineStatsAtucTssi1 OCTET STRING
  adslLineStatsAtucTssi2 OCTET STRING
  adslLineStatsAturTssi OCTET STRING
  adslLineStatsAtucGain1 OCTET STRING
  adslLineStatsAtucGain2 OCTET STRING
  adslLineStatsAturGain OCTET STRING
  adslLineStatsAtucBits1 OCTET STRING
  adslLineStatsAtucBits2 OCTET STRING
  adslLineStatsAturBits OCTET STRING

AdslLinePerfEntry  
SEQUENCE    
  adslLinePerfAtucCrcFast Counter32
  adslLinePerfAturCrcFast Counter32
  adslLinePerfAtucFecFast Counter32
  adslLinePerfAturFecFast Counter32
  adslLinePerfAtucCrcInterleave Counter32
  adslLinePerfAturCrcInterleave Counter32
  adslLinePerfAtucFecInterleave Counter32
  adslLinePerfAturFecInterleave Counter32
  adslLinePerfAtucEs Counter32
  adslLinePerfAturEs Counter32
  adslLinePerfAtucSes Counter32
  adslLinePerfAturSes Counter32
  adslLinePerfAtucUas Counter32
  adslLinePerfAturUas Counter32
  adslLinePerfAtucLofs Counter32
  adslLinePerfAturLofs Counter32
  adslLinePerfAtucLoss Counter32
  adslLinePerfAturLoss Counter32
  adslLinePerfAtucLprs Counter32
  adslLinePerfAturLprs Counter32

ShdslLinePerfEntry  
SEQUENCE    
  shdslLinePerfEs Counter32
  shdslLinePerfSes Counter32
  shdslLinePerfCrc Counter32
  shdslLinePerfLosws Counter32
  shdslLinePerfUas Counter32
  shdslLinePerfSegmentAnomalies Counter32
  shdslLinePerfSegmentDefect Counter32

ShdslPerfCurrEntry  
SEQUENCE    
  shdslPerfCurrSturLPR Counter32

IpInterfaceEntry  
SEQUENCE    
  ipInterface INTEGER
  ipAddress IpAddress
  ipNetmask IpAddress
  ipBroadcast IpAddress
  ipMtu INTEGER
  ipVid VlanIndex
  ipInOctet Counter32
  ipInUnicast Counter32
  ipInMulticast Counter32
  ipInDiscard Counter32
  ipInError Counter32
  ipInUnknown Counter32
  ipOutOctet Counter32
  ipOutUnicast Counter32
  ipOutMulticast Counter32
  ipOutDiscard Counter32
  ipOutError Counter32

MstpPortStatsEntry  
SEQUENCE    
  mstpPortStatsExternalRootId BridgeId
  mstpPortStatsExternalRootCost INTEGER
  mstpPortStatsExternalPortCost INTEGER
  mstpPortStatsOperEdgePort INTEGER
  mstpPortStatsOperPoint2Point INTEGER
  mstpPortStatsMACOperational INTEGER
  mstpPortStatsRecvInternal INTEGER
  mstpPortStatsRxStpCfgBPDU Counter32
  mstpPortStatsRxStpTcnBPDU Counter32
  mstpPortStatsRxRstpBPDU Counter32
  mstpPortStatsRxMstpBPDU Counter32

MstpXstStatsEntry  
SEQUENCE    
  mstpXstStatsBridgeId BridgeId
  mstpXstStatsTimeSinceTopologyChange TimeTicks
  mstpXstStatsTopologyChangesCount Counter32
  mstpXstStatsInternalRootPortId OCTET STRING
  mstpXstStatsInternalRootId BridgeId
  mstpXstStatsInternalRootCost INTEGER

MstpXstPortStatsEntry  
SEQUENCE    
  mstpXstPortStatsUptime TimeTicks
  mstpXstPortStatsPortId OCTET STRING
  mstpXstPortStatsState INTEGER
  mstpXstPortStatsDesignatedBridgeId BridgeId
  mstpXstPortStatsDesignatedPortId OCTET STRING
  mstpXstPortStatsInternalPortCost INTEGER
  mstpXstPortStatsInternalRootId BridgeId

VdslLinePerfEntry  
SEQUENCE    
  vdslLinePerfVtucCrc Counter32
  vdslLinePerfVturCrc Counter32
  vdslLinePerfVtucFec Counter32
  vdslLinePerfVturFec Counter32
  vdslLinePerfVtucLofs Counter32
  vdslLinePerfVturLofs Counter32
  vdslLinePerfVtucLoss Counter32
  vdslLinePerfVturLoss Counter32
  vdslLinePerfVtucLprs Counter32
  vdslLinePerfVturLprs Counter32
  vdslLinePerfVtucLols Counter32
  vdslLinePerfVturLols Counter32
  vdslLinePerfVtucESs Counter32
  vdslLinePerfVturESs Counter32
  vdslLinePerfVtucSESs Counter32
  vdslLinePerfVturSESs Counter32
  vdslLinePerfVtucUASs Counter32
  vdslLinePerfVturUASs Counter32
  vdslLinePerfInmVtucEqInp Counter32
  vdslLinePerfInmVturEqInp Counter32
  vdslLinePerfInmVtucIAT Counter32
  vdslLinePerfInmVturIAT Counter32
  vdslLinePerfInmVtucME Counter32
  vdslLinePerfInmVturME Counter32
  vdslLinePerfVtucRx Unsigned32
  vdslLinePerfVturRx Unsigned32
  vdslLinePerfVtucRxCorrected Unsigned32
  vdslLinePerfVturRxCorrected Unsigned32
  vdslLinePerfVtucRxUncorrected Unsigned32
  vdslLinePerfVturRxUncorrected Unsigned32
  vdslLinePerfVtucLEFTRs Unsigned32
  vdslLinePerfVturLEFTRs Unsigned32
  vdslLinePerfVtucErrFreeBits Unsigned32
  vdslLinePerfVturErrFreeBits Unsigned32
  vdslLinePerfVtucMinEftr Counter32
  vdslLinePerfVturMinEftr Counter32

VdslLineStatsEntry  
SEQUENCE    
  vdslLineStatsVtucBits1 OCTET STRING
  vdslLineStatsVtucBits2 OCTET STRING
  vdslLineStatsVtucBits3 OCTET STRING
  vdslLineStatsVtucBits4 OCTET STRING
  vdslLineStatsVturBits1 OCTET STRING
  vdslLineStatsVturBits2 OCTET STRING
  vdslLineStatsVturBits3 OCTET STRING
  vdslLineStatsVturBits4 OCTET STRING
  vdslLineStatsVtucGain1 OCTET STRING
  vdslLineStatsVtucGain2 OCTET STRING
  vdslLineStatsVtucGain3 OCTET STRING
  vdslLineStatsVtucGain4 OCTET STRING
  vdslLineStatsVtucGain5 OCTET STRING
  vdslLineStatsVtucGain6 OCTET STRING
  vdslLineStatsVtucGain7 OCTET STRING
  vdslLineStatsVtucGain8 OCTET STRING
  vdslLineStatsVturGain1 OCTET STRING
  vdslLineStatsVturGain2 OCTET STRING
  vdslLineStatsVturGain3 OCTET STRING
  vdslLineStatsVturGain4 OCTET STRING
  vdslLineStatsVturGain5 OCTET STRING
  vdslLineStatsVturGain6 OCTET STRING
  vdslLineStatsVturGain7 OCTET STRING
  vdslLineStatsVturGain8 OCTET STRING
  vdslLineStatsVtucHlog OCTET STRING
  vdslLineStatsVturHlog OCTET STRING
  vdslLineStatsVtucQln OCTET STRING
  vdslLineStatsVturQln OCTET STRING
  vdslLineStatsVtucSnr OCTET STRING
  vdslLineStatsVturSnr OCTET STRING
  vdslLineStatsVtucTssi OCTET STRING
  vdslLineStatsVturTssi OCTET STRING
  vdslLineStatsProtocol INTEGER
  vdslLineStatsUsCodingMode INTEGER
  vdslLineStatsDsCodingMode INTEGER
  vdslLineStatsVtucHlogGroupSize INTEGER
  vdslLineStatsVturHlogGroupSize INTEGER
  vdslLineStatsVtucQlnGroupSize INTEGER
  vdslLineStatsVturQlnGroupSize INTEGER
  vdslLineStatsVtucSnrGroupSize INTEGER
  vdslLineStatsVturSnrGroupSize INTEGER
  vdslLineStatsVtucRxPower INTEGER
  vdslLineStatsVturRxPower INTEGER
  vdslLineStatsVtucSnrMargin INTEGER
  vdslLineStatsVturSnrMargin INTEGER
  vdslLineStatsVtucSigAtten INTEGER
  vdslLineStatsVturSigAtten INTEGER
  vdslLineStatsVtucLineAtten INTEGER
  vdslLineStatsVturLineAtten INTEGER

VdslLineUsBandPlanEntry  
SEQUENCE    
  vdslLineUsBandId INTEGER
  vdslLineUsBandStartToneId INTEGER
  vdslLineUsBandStopToneId INTEGER

VdslLineDsBandPlanEntry  
SEQUENCE    
  vdslLineDsBandId INTEGER
  vdslLineDsBandStartToneId INTEGER
  vdslLineDsBandStopToneId INTEGER

VdslLineUsResultMaskEntry  
SEQUENCE    
  vdslLineUsMaskId INTEGER
  vdslLineUsMaskTone INTEGER
  vdslLineUsMaskPsd INTEGER

VdslLineDsResultMaskEntry  
SEQUENCE    
  vdslLineDsMaskId INTEGER
  vdslLineDsMaskTone INTEGER
  vdslLineDsMaskPsd INTEGER

VdslLinePerfCurrEntry  
SEQUENCE    
  vdslLinePerfCurrInmVtucEqInp Counter32
  vdslLinePerfCurrInmVturEqInp Counter32
  vdslLinePerfCurr15MInmVtucEqInp Counter32
  vdslLinePerfCurr15MInmVturEqInp Counter32
  vdslLinePerfCurr1DayInmVtucEqInp Counter32
  vdslLinePerfCurr1DayInmVturEqInp Counter32
  vdslLinePerfCurrInmVtucIAT Counter32
  vdslLinePerfCurrInmVturIAT Counter32
  vdslLinePerfCurr15MInmVtucIAT Counter32
  vdslLinePerfCurr15MInmVturIAT Counter32
  vdslLinePerfCurr1DayInmVtucIAT Counter32
  vdslLinePerfCurr1DayInmVturIAT Counter32
  vdslLinePerfCurrInmVtucME Counter32
  vdslLinePerfCurrInmVturME Counter32
  vdslLinePerfCurr15MInmVtucME Counter32
  vdslLinePerfCurr15MInmVturME Counter32
  vdslLinePerfCurr1DayInmVtucME Counter32
  vdslLinePerfCurr1DayInmVturME Counter32
  vdslLinePerfCurrVtucRx Unsigned32
  vdslLinePerfCurrVturRx Unsigned32
  vdslLinePerfCurr15MVtucRx Unsigned32
  vdslLinePerfCurr15MVturRx Unsigned32
  vdslLinePerfCurr1DayVtucRx Unsigned32
  vdslLinePerfCurr1DayVturRx Unsigned32
  vdslLinePerfCurrVtucRxCorrected Unsigned32
  vdslLinePerfCurrVturRxCorrected Unsigned32
  vdslLinePerfCurr15MVtucRxCorrected Unsigned32
  vdslLinePerfCurr15MVturRxCorrected Unsigned32
  vdslLinePerfCurr1DayVtucRxCorrected Unsigned32
  vdslLinePerfCurr1DayVturRxCorrected Unsigned32
  vdslLinePerfCurrVtucRxUncorrected Unsigned32
  vdslLinePerfCurrVturRxUncorrected Unsigned32
  vdslLinePerfCurr15MVtucRxUncorrected Unsigned32
  vdslLinePerfCurr15MVturRxUncorrected Unsigned32
  vdslLinePerfCurr1DayVtucRxUncorrected Unsigned32
  vdslLinePerfCurr1DayVturRxUncorrected Unsigned32
  vdslLinePerfCurrVtucLEFTRs Unsigned32
  vdslLinePerfCurrVturLEFTRs Unsigned32
  vdslLinePerfCurr15MVtucLEFTRs Unsigned32
  vdslLinePerfCurr15MVturLEFTRs Unsigned32
  vdslLinePerfCurr1DayVtucLEFTRs Unsigned32
  vdslLinePerfCurr1DayVturLEFTRs Unsigned32
  vdslLinePerfCurrVtucErrFreeBits Unsigned32
  vdslLinePerfCurrVturErrFreeBits Unsigned32
  vdslLinePerfCurr15MVtucErrFreeBits Unsigned32
  vdslLinePerfCurr15MVturErrFreeBits Unsigned32
  vdslLinePerfCurr1DayVtucErrFreeBits Unsigned32
  vdslLinePerfCurr1DayVturErrFreeBits Unsigned32
  vdslLinePerfCurrVtucMinEftr Counter32
  vdslLinePerfCurrVturMinEftr Counter32
  vdslLinePerfCurr15MinVtucMinEftr Counter32
  vdslLinePerfCurr15MinVturMinEftr Counter32
  vdslLinePerfCurr1DayVtucMinEftr Counter32
  vdslLinePerfCurr1DayVturMinEftr Counter32

VdslLinePerfHist15MinEntry  
SEQUENCE    
  vdslLinePerfHist15MInmVtucEqInp Counter32
  vdslLinePerfHist15MInmVturEqInp Counter32
  vdslLinePerfHist15MInmVtucIAT Counter32
  vdslLinePerfHist15MInmVturIAT Counter32
  vdslLinePerfHist15MInmVtucME Counter32
  vdslLinePerfHist15MInmVturME Counter32
  vdslLinePerfHist15MVtucRtx Unsigned32
  vdslLinePerfHist15MVturRtx Unsigned32
  vdslLinePerfHist15MVtucRtxCorrected Unsigned32
  vdslLinePerfHist15MVturRtxCorrected Unsigned32
  vdslLinePerfHist15MVtucRtxUncorrected Unsigned32
  vdslLinePerfHist15MVturRtxUncorrected Unsigned32
  vdslLinePerfHist15MVtucLEFTRs Unsigned32
  vdslLinePerfHist15MVturLEFTRs Unsigned32
  vdslLinePerfHist15MVtucErrFreeBits Unsigned32
  vdslLinePerfHist15MVturErrFreeBits Unsigned32
  vdslLinePerfHist15MVtucMinEftr Counter32
  vdslLinePerfHist15MVturMinEftr Counter32

VdslLinePerfHist1DayEntry  
SEQUENCE    
  vdslLinePerfHist1DayInmVtucEqInp Counter32
  vdslLinePerfHist1DayInmVturEqInp Counter32
  vdslLinePerfHist1DayInmVtucIAT Counter32
  vdslLinePerfHist1DayInmVturIAT Counter32
  vdslLinePerfHist1DayInmVtucME Counter32
  vdslLinePerfHist1DayInmVturME Counter32
  vdslLinePerfHist1DayVtucRtx Unsigned32
  vdslLinePerfHist1DayVturRtx Unsigned32
  vdslLinePerfHist1DayVtucRtxCorrected Unsigned32
  vdslLinePerfHist1DayVturRtxCorrected Unsigned32
  vdslLinePerfHist1DayVtucRtxUncorrected Unsigned32
  vdslLinePerfHist1DayVturRtxUncorrected Unsigned32
  vdslLinePerfHist1DayVtucLEFTRs Unsigned32
  vdslLinePerfHist1DayVturLEFTRs Unsigned32
  vdslLinePerfHist1DayVtucErrFreeBits Unsigned32
  vdslLinePerfHist1DayVturErrFreeBits Unsigned32
  vdslLinePerfHist1DayVtucMinEftr Counter32
  vdslLinePerfHist1DayVturMinEftr Counter32

VdslChanStatsEntry  
SEQUENCE    
  vdslChanActualRaMode Xdsl2StatusActualRaMode
  vdslChanRetransmissionMode Xdsl2StatusRtxMode
  vdslChanRetransmissionOverhead Unsigned32

PaepvcSessionEntry  
SEQUENCE    
  paepvcSessionVpi INTEGER
  paepvcSessionVci INTEGER
  paepvcSessionState INTEGER
  paepvcSessionId INTEGER
  paepvcSessionUpTime Unsigned32
  paepvcSessionAcName DisplayString
  paepvcSessionSrvcName DisplayString

PaepvcCountEntry  
SEQUENCE    
  paepvcCountVpi INTEGER
  paepvcCountVci INTEGER
  paepvcCountPppLcpCfgReqRx Unsigned32
  paepvcCountPppLcpEchoReqRx Unsigned32
  paepvcCountPppLcpEchoReplyRx Unsigned32
  paepvcCountPadiTx Unsigned32
  paepvcCountPadoRx Unsigned32
  paepvcCountPadrTx Unsigned32
  paepvcCountPadsRx Unsigned32
  paepvcCountPadtTx Unsigned32
  paepvcCountPadtRx Unsigned32
  paepvcCountSrvcnameErrRx Unsigned32
  paepvcCountAcnameErrRx Unsigned32
  paepvcCountGenericErrTx Unsigned32
  paepvcCountGenericErrRx Unsigned32

VlanMacEntry  
SEQUENCE    
  vlanMacAddress MacAddress
  vlanMacPort INTEGER
  vlanMacStatus INTEGER

ArpproxyEntry  
SEQUENCE    
  arpproxyIp IpAddress
  arpproxyMac MacAddress
  arpproxyIfIndex INTEGER
  arpproxyVpi INTEGER
  arpproxyVci INTEGER
  arpproxyInterfaceIp IpAddress
  arpproxyInterfaceMask INTEGER
  arpproxyInterfaceVid VlanIndex
  arpproxyDhcpIp INTEGER
  arpproxyType INTEGER

IpbpvcIfDynamicEntry  
SEQUENCE    
  ipbpvcIfDynamicIp IpAddress
  ipbpvcIfDynamicMask INTEGER
  ipbpvcIfDynamicIfIndex INTEGER
  ipbpvcIfDynamicVpi INTEGER
  ipbpvcIfDynamicVci INTEGER

IpbpvcRouteDynamicEntry  
SEQUENCE    
  ipbpvcRouteDynamicType INTEGER
  ipbpvcRouteDynamicIp IpAddress
  ipbpvcRouteDynamicMask INTEGER
  ipbpvcRouteDynamicNextHop IpAddress
  ipbpvcRouteDynamicMetric INTEGER
  ipbpvcRouteDynamicPriority INTEGER

VoipLineStatusEntry  
SEQUENCE    
  voipLineStatusFxsStatus INTEGER
  voipLineStatusServiceStatus INTEGER

VoipLineInfoEntry  
SEQUENCE    
  voipLineInfoSipLocalUri DisplayString
  voipLineInfoSipRemoteUri DisplayString
  voipLineInfoRtpTxCodecType DisplayString
  voipLineInfoRtpRxCodecType DisplayString
  voipLineInfoRtpTxPt INTEGER
  voipLineInfoRtpRxPt INTEGER
  voipLineInfoRtpLocalIp IpAddress
  voipLineInfoRtpRemoteIp IpAddress
  voipLineInfoRtpLocalPort INTEGER
  voipLineInfoRtpRemotePort INTEGER
  voipLineInfoLastCidMode INTEGER
  voipLineInfoPlaySignalTel INTEGER
  voipLineInfoPlaySignalNet INTEGER

VoipH248StatEntry  
SEQUENCE    
  voipH248StatSlot INTEGER
  voipH248StatMgName DisplayString
  voipH248StatMgState INTEGER

VoipSipStatEntry  
SEQUENCE    
  voipSipStatSlot INTEGER
  voipSipStatProxyIndex INTEGER
  voipSipStatProxySvr DisplayString
  voipSipStatProxyPort INTEGER
  voipSipStatState INTEGER

VoipH248InterfaceStatEntry  
SEQUENCE    
  voipH248InterfaceStatId INTEGER
  voipH248InterfaceStatMgState INTEGER
  voipH248InterfaceStatPrimarySlot INTEGER
  voipH248InterfaceStatSecondarySlot INTEGER
  voipH248InterfaceStatPrimaryProtectionState INTEGER
  voipH248InterfaceStatSecondaryProtectionState INTEGER
  voipH248InterfaceStatRedundantState INTEGER

VoipH248MediaStatEntry  
SEQUENCE    
  voipH248MediaStatInterfaceId INTEGER
  voipH248MediaStatSlaveId INTEGER
  voipH248MediaStatSlaveIp INTEGER
  voipH248MediaStatMgmtInbandIp INTEGER
  voipH248MediaStatMgmtOutbandIp INTEGER
  voipH248MediaStatSlotId INTEGER
  voipH248MediaStatPortCount INTEGER
  voipH248MediaStatState INTEGER

VoipH248TerminationStatEntry  
SEQUENCE    
  voipH248TerminationStatStateId INTEGER
  voipH248TerminationStatStateMediaId INTEGER
  voipH248TerminationStatStatePortNumber INTEGER
  voipH248TerminationStatName DisplayString
  voipH248TerminationStatPhoneState INTEGER
  voipH248TerminationStatCallServiceState INTEGER

VoipRtpStatEntry  
SEQUENCE    
  voipRtpStatTxRate INTEGER
  voipRtpStatRxRate INTEGER
  voipRtpStatTxPktCnt Counter64
  voipRtpStatRxPktCnt Counter64
  voipRtpStatTxFracLost INTEGER
  voipRtpStatRxFracLost INTEGER
  voipRtpStatTxJitter Counter64
  voipRtpStatRxJitter Counter64
  voipRtpStatTxAvgDelay Counter64
  voipRtpStatRxAvgDelay Counter64

VoipCdrStatResultEntry  
SEQUENCE    
  voipCdrStatResultIndex INTEGER
  voipCdrStatResultSlot INTEGER
  voipCdrStatResultPort INTEGER
  voipCdrStatResultTermName DisplayString
  voipCdrStatResultLineDirection INTEGER
  voipCdrStatResultLocalNumber DisplayString
  voipCdrStatResultRemoteNumber DisplayString
  voipCdrStatResultOffHookDatetime DisplayString
  voipCdrStatResultOnHookDatetime DisplayString
  voipCdrStatResultRingStartDatetime DisplayString
  voipCdrStatResultRingStopDatetime DisplayString
  voipCdrStatResultRtpStartDatetime DisplayString
  voipCdrStatResultRtpStopDatetime DisplayString
  voipCdrStatResultRtpElapsedTime INTEGER
  voipCdrStatResultTxRate INTEGER
  voipCdrStatResultRxRate INTEGER
  voipCdrStatResultTxPktCnt Counter64
  voipCdrStatResultRxPktCnt Counter64
  voipCdrStatResultTxFracLost INTEGER
  voipCdrStatResultRxFracLost INTEGER
  voipCdrStatResultTxJitter Counter64
  voipCdrStatResultRxJitter Counter64
  voipCdrStatResultTxAvgDelay Counter64
  voipCdrStatResultRxAvgDelay Counter64
  voipCdrStatResultCode INTEGER
  voipCdrStatResultErrCode INTEGER
  voipCdrStatResultTerminationCause DisplayString

EnetPortStatusEntry  
SEQUENCE    
  enetPortStatusLinkUpType INTEGER
  enetPortStatusLinkUpTime Unsigned32
  enetPortStatusLinkSpeed Unsigned32
  enetPortStatusLinkDuplex INTEGER
  enetPortStatusDataRateTx Unsigned32
  enetPortStatusDataRateRx Unsigned32
  enetPortStatusDataUtilTx INTEGER
  enetPortStatusDataUtilRx INTEGER

SfpPortStatusEntry  
SEQUENCE    
  sfpId DisplayString
  sfpConnector DisplayString
  sfpTransceiver DisplayString
  sfpEncoding DisplayString
  sfpName DisplayString
  sfpPartNumber DisplayString
  sfpRevision DisplayString
  sfpSerialNumber DisplayString
  sfpTemperature Unsigned32
  sfpSupplyVoltage Unsigned32
  sfpTxBiasCurrent Unsigned32
  sfpTxPower Unsigned32
  sfpRxPower Unsigned32

IfStatusEntry  
SEQUENCE    
  ifInRate Counter32
  ifOutRate Counter32
  ifCurrentStatus INTEGER
  ifUpTime Unsigned32

ImaPvcStatsEntry  
SEQUENCE    
  imaPvcStatsGroupIndex INTEGER
  imaPvcStatsVpi INTEGER
  imaPvcStatsVci INTEGER
  imaPvcStatsTxPackets Counter64
  imaPvcStatsRxPackets Counter64
  imaPvcStatsTxUnicast Counter64
  imaPvcStatsRxUnicast Counter64
  imaPvcStatsTxMulticast Counter64
  imaPvcStatsRxMulticast Counter64
  imaPvcStatsTxBroadcast Counter64
  imaPvcStatsRxBroadcast Counter64
  imaPvcStatsTxDiscard Counter64
  imaPvcStatsRxDiscard Counter64

ImaGroupStatsEntry  
SEQUENCE    
  imaGroupStatsGroupIndex INTEGER
  imaGroupStatsTxCells Counter64
  imaGroupStatsRxCells Counter64
  imaGroupStatsTxRate INTEGER
  imaGroupStatsRxRate INTEGER
  imaGroupStatsCrcErr Counter64

ImaGroupCurrDayEntry  
SEQUENCE    
  imaGroupCurrDayGroupIndex INTEGER
  imaGroupCurrDayUnavailSecs INTEGER
  imaGroupCurrDayNeNumFailures INTEGER
  imaGroupCurrDayFeNumFailures INTEGER

ImaLinkCurrDayEntry  
SEQUENCE    
  imaLinkCurrDayIfindex INTEGER
  imaLinkCurrDayImaViolations INTEGER
  imaLinkCurrDayOifAnomalies INTEGER
  imaLinkCurrDayNeSevErroredSecs INTEGER
  imaLinkCurrDayFeSevErroredSecs INTEGER
  imaLinkCurrDayNeUnavailSecs INTEGER
  imaLinkCurrDayFeUnavailSecs INTEGER
  imaLinkCurrDayNeTxUnusableSecs INTEGER
  imaLinkCurrDayNeRxUnusableSecs INTEGER
  imaLinkCurrDayFeTxUnusableSecs INTEGER
  imaLinkCurrDayFeRxUnusableSecs INTEGER
  imaLinkCurrDayNeTxNumFailures INTEGER
  imaLinkCurrDayNeRxNumFailures INTEGER
  imaLinkCurrDayFeTxNumFailures INTEGER
  imaLinkCurrDayFeRxNumFailures INTEGER
  imaLinkCurrDayTxStuffs INTEGER
  imaLinkCurrDayRxStuffs INTEGER

ImaGroupConfReadyEntry  
SEQUENCE    
  imaGroupConfReadyIndex INTEGER
  imaGroupConfReadyState INTEGER

ImaGroupStatusEntry  
SEQUENCE    
  imaGroupStatusGroupIndex INTEGER
  imaGroupStatusTxPayloadRate INTEGER
  imaGroupStatusRxPayloadRate INTEGER

E1CurrDayEntry  
SEQUENCE    
  e1CurrDayIfindex INTEGER
  e1CurrDayLCVs INTEGER
  e1CurrDayPCVs INTEGER
  e1CurrDayESs INTEGER
  e1CurrDaySESs INTEGER
  e1CurrDayUASs INTEGER

E1StatusEntry  
SEQUENCE    
  e1StatusIfindex INTEGER
  e1StatusTxPayloadRate INTEGER
  e1StatusRxPayloadRate INTEGER
  e1StatusUpTime Unsigned32

LoopguardStatsEntry  
SEQUENCE    
  loopguardStatsPort INTEGER
  loopguardStatsPortStatus INTEGER
  loopguardStatsLoopguardStatus INTEGER
  loopguardStatsTotalTxPackets INTEGER
  loopguardStatsTotalRxPackets INTEGER
  loopguardStatsBadPackets INTEGER
  loopguardStatsShutdownTime DisplayString

StpPortStatsEntry  
SEQUENCE    
  stpPortStatus INTEGER

GbondStatsEntry  
SEQUENCE    
  gbondStatsName DisplayString
  gbondStatsUpRate Unsigned32
  gbondStatsDownRate Unsigned32
  gbondStatsMember OCTET STRING
  gbondStatslinkup OCTET STRING
  gbondStatsTx OCTET STRING
  gbondStatsRx OCTET STRING
  gbondStatslinkdown OCTET STRING
  gbondStatsTCMode INTEGER
  gbondStatsTxRate Unsigned32
  gbondStatsRxRate Unsigned32

VdslChanExtendedEntry  
SEQUENCE    
  vdslChanPrevTxRate Gauge32
  vdslChanActualRaMode Xdsl2StatusActualRaMode
  vdslChanRetransmissionMode Xdsl2StatusRtxMode
  vdslChanRetransmissionOverhead Unsigned32
  vdslChanGinpFramingType Unsigned32
  vdslChanActualInpAgainstREIN Unsigned32
  vdslChanReedSolomonCodeWordPerDtu Unsigned32

VdslPerfDataExtendedEntry  
SEQUENCE    
  vdslPerfDataFECs Unsigned32

VdslChanPerfDataExtendedEntry  
SEQUENCE    
  vdslChanPerfDataCorrectedBlks Counter32
  vdslChanPerfDataUncorrectBlks Counter32
  vdslChanPerfDataCodeViolations Unsigned32

Xdsl2PMLineCurrExtendedEntry  
SEQUENCE    
  xdsl2PMLCurr15MMonitoredTime INTEGER
  xdsl2PMLCurr15MLofs Counter32
  xdsl2PMLCurr15MLols Counter32
  xdsl2PMLCurr15MLol Counter32
  xdsl2PMLCurr15MLprs Counter32
  xdsl2PMLCurr15MLpr Counter32
  xdsl2PMLCurr15MInits Counter32
  xdsl2PMLCurr1DayMonitoredTime INTEGER
  xdsl2PMLCurr1DayLofs Counter32
  xdsl2PMLCurr1DayLols Counter32
  xdsl2PMLCurr1DayLol Counter32
  xdsl2PMLCurr1DayLprs Counter32
  xdsl2PMLCurr1DayLpr Counter32
  xdsl2PMLCurr1DayInits Counter32
  xdsl2PMLSinceLinkInmEqInp OCTET STRING
  xdsl2PMLSinceLinkInmIAT OCTET STRING
  xdsl2PMLSinceLinkInmME Counter32
  xdsl2PMLCurr15MInmEqInp OCTET STRING
  xdsl2PMLCurr15MInmIAT OCTET STRING
  xdsl2PMLCurr15MInmME Counter32
  xdsl2PMLCurr1DayInmEqInp OCTET STRING
  xdsl2PMLCurr1DayInmIAT OCTET STRING
  xdsl2PMLCurr1DayInmME Counter32
  xdsl2PMLSinceInitLofs Counter32
  xdsl2PMLSinceInitLols Counter32
  xdsl2PMLSinceInitLol Counter32
  xdsl2PMLSinceInitLprs Counter32
  xdsl2PMLSinceInitLpr Counter32
  xdsl2PMLSinceInitInits Counter32

Xdsl2PMLineHist15MinExtendedEntry  
SEQUENCE    
  xdsl2PMLHist15MLofs Counter32
  xdsl2PMLHist15MLols Counter32
  xdsl2PMLHist15MLol Counter32
  xdsl2PMLHist15MLprs Counter32
  xdsl2PMLHist15MLpr Counter32
  xdsl2PMLHist15MInits Counter32
  xdsl2PMLHist15MInmEqInp OCTET STRING
  xdsl2PMLHist15MInmIAT OCTET STRING
  xdsl2PMLHist15MInmME Counter32

Xdsl2PMLineHist1DayExtendedEntry  
SEQUENCE    
  xdsl2PMLHist1DLofs Counter32
  xdsl2PMLHist1DLols Counter32
  xdsl2PMLHist1DLol Counter32
  xdsl2PMLHist1DLprs Counter32
  xdsl2PMLHist1DLpr Counter32
  xdsl2PMLHist1DInits Counter32
  xdsl2PMLHist1DInmEqInp OCTET STRING
  xdsl2PMLHist1DInmIAT OCTET STRING
  xdsl2PMLHist1DInmME Counter32

Xdsl2PMChCurrExtendedEntry  
SEQUENCE    
  xdsl2PMChCurr15MUncorrectBlks Counter32
  xdsl2PMChCurr1DayUncorrectBlks Counter32
  xdsl2PMChSinceLinkRtx Unsigned32
  xdsl2PMChCurr15MRtx Unsigned32
  xdsl2PMChCurr1DayRtx Unsigned32
  xdsl2PMChSinceLinkRtxCorrected Unsigned32
  xdsl2PMChCurr15MRtxCorrected Unsigned32
  xdsl2PMChCurr1DayRtxCorrected Unsigned32
  xdsl2PMChSinceLinkRtxUncorrected Unsigned32
  xdsl2PMChCurr15MRtxUncorrected Unsigned32
  xdsl2PMChCurr1DayRtxUncorrected Unsigned32
  xdsl2PMChSinceLinkLEFTRs Unsigned32
  xdsl2PMChCurr15MLEFTRs Unsigned32
  xdsl2PMChCurr1DayLEFTRs Unsigned32
  xdsl2PMChSinceLinkMinEFTR Unsigned32
  xdsl2PMChCurr15MMinEFTR Unsigned32
  xdsl2PMChCurr1DayMinEFTR Unsigned32
  xdsl2PMChSinceLinkErrFreeBits Unsigned32
  xdsl2PMChCurr15MErrFreeBits Unsigned32
  xdsl2PMChCurr1DayErrFreeBits Unsigned32

Xdsl2PMChHist15MinExtendedEntry  
SEQUENCE    
  xdsl2PMChHist15MUncorrectBlks Counter32
  xdsl2PMChHist15MRtx Unsigned32
  xdsl2PMChHist15MRtxCorrected Unsigned32
  xdsl2PMChHist15MRtxUncorrected Unsigned32
  xdsl2PMChHist15MLEFTRs Unsigned32
  xdsl2PMChHist15MMinEFTR Unsigned32
  xdsl2PMChHist15MErrFreeBits Unsigned32

Xdsl2PMChHist1DExtendedEntry  
SEQUENCE    
  xdsl2PMChHist1DUncorrectBlks Counter32
  xdsl2PMChHist1DayRtx Unsigned32
  xdsl2PMChHist1DayRtxCorrected Unsigned32
  xdsl2PMChHist1DayRtxUncorrected Unsigned32
  xdsl2PMChHist1DayLEFTRs Unsigned32
  xdsl2PMChHist1DayMinEFTR Unsigned32
  xdsl2PMChHist1DayErrFreeBits Unsigned32

Xdsl2LineBandExtEntry  
SEQUENCE    
  xdsl2LineBandTxPower INTEGER
  xdsl2LineBandRxPower INTEGER

MldGroupEntry  
SEQUENCE    
  mldGroupVid VlanIndex
  mldGroupIp InetAddress
  mldGroupNumOfMembers INTEGER
  mldGroupMemberPorts PortList
  mldGroupNumOfActiveUsers INTEGER

MldGroupPortEntry  
SEQUENCE    
  mldGroupPortVid VlanIndex
  mldGroupPortIp InetAddress
  mldGroupPortSourceIp InetAddress

MldPortCtrlPduEntry  
SEQUENCE    
  mldPortCtrlPduQueryCnt Counter32
  mldPortCtrlPduReportCnt Counter32
  mldPortCtrlPduLeaveCnt Counter32
  mldPortNumOfActiveGroups INTEGER
  mldPortCtrlPduV1SuccessJoinCnt Counter32
  mldPortCtrlPduV1UnsuccJoinCnt Counter32
  mldPortCtrlPduGenQryCnt Counter32
  mldPortCtrlPduSpecQryCnt Counter32
  mldPortCtrlPduV2SuccessReportCnt Counter32
  mldPortCtrlPduV2UnsuccReportCnt Counter32
  mldPortCtrlPduInvalidCnt Counter32

MldVlanStatsuEntry  
SEQUENCE    
  mldVlanStatsVlanIndex VlanIndex
  mldVlanStatsNumOfActiveGroups INTEGER
  mldVlanStatsQueryPort INTEGER
  mldVlanStatsQuerierIp InetAddress
  mldVlanStatsV1QueryInCnt Counter32
  mldVlanStatsV1ReportInCnt Counter32
  mldVlanStatsV1DoneInCnt Counter32
  mldVlanStatsV1QueryInDropCnt Counter32
  mldVlanStatsV1ReportInDropCnt Counter32
  mldVlanStatsV1DoneInDropCnt Counter32
  mldVlanStatsV1QueryOutCnt Counter32
  mldVlanStatsV1ReportOutCnt Counter32
  mldVlanStatsV1DoneOutCnt Counter32
  mldVlanStatsV2QueryInCnt Counter32
  mldVlanStatsV2ReportInCnt Counter32
  mldVlanStatsV2QueryInDropCnt Counter32
  mldVlanStatsV2ReportInDropCnt Counter32
  mldVlanStatsV2QueryOutCnt Counter32
  mldVlanStatsV2ReportOutCnt Counter32

MacFFArpStatusUplinkEntry  
SEQUENCE    
  macFFArpStatusUplinkIpAddr IpAddress
  macFFArpStatusUplinkMacAddr PhysAddress
  macFFArpStatusUplinkMacVid INTEGER

MacFFArpStatusSlotEntry  
SEQUENCE    
  macFFArpStatusSlotIpAddr IpAddress
  macFFArpStatusSlotMacAddr PhysAddress
  macFFArpStatusSlotMacVid INTEGER
  macFFArpStatusSlotPort INTEGER

MacFFArpCntUplinkEntry  
SEQUENCE    
  macFFArpCntUplinkReqRx Unsigned32
  macFFArpCntUplinkReqTx Unsigned32
  macFFArpCntUplinkReqRxDrop Unsigned32
  macFFArpCntUplinkRpyRx Unsigned32
  macFFArpCntUplinkRpyTx Unsigned32
  macFFArpCntUplinkRpyRxDrop Unsigned32

MacFFArpCntPortEntry  
SEQUENCE    
  macFFArpCntPortReqRx Unsigned32
  macFFArpCntPortReqTx Unsigned32
  macFFArpCntPortReqRxDrop Unsigned32
  macFFArpCntPortRpyRx Unsigned32
  macFFArpCntPortRpyTx Unsigned32
  macFFArpCntPortRpyRxDrop Unsigned32

SysFlashFwInfoEntry  
SEQUENCE    
  sysFlashFwIndex INTEGER
  sysFlashFwVersion DisplayString

ClusterCandidateEntry  
SEQUENCE    
  clusterCandidateMacAddr MacAddress
  clusterCandidateHostName DisplayString
  clusterCandidateModelName DisplayString
  clusterCandidateDeviceType INTEGER

ClusterMemberConfEntry  
SEQUENCE    
  clusterMemberConfId INTEGER
  clusterMemberConfMacAddr MacAddress
  clusterMemberConfPasswd DisplayString

ClusterMemberStatusEntry  
SEQUENCE    
  clusterMemberStatusState INTEGER
  clusterMemberStatusMacAddr MacAddress
  clusterMemberStatusHostName DisplayString
  clusterMemberStatusModelName DisplayString
  clusterMemberStatusDeviceType INTEGER
  clusterMemberStatusFWVersion DisplayString
  clusterMemberStatusUpTime TimeTicks

VoipArpShowEntry  
SEQUENCE    
  voipArpShowIp IpAddress
  voipArpShowMac PhysAddress
  voipArpShowTimer INTEGER

VoipNumberPlanEntry  
SEQUENCE    
  voipNumberPlanName DisplayString
  voipNumberPlanIndex INTEGER
  voipNumberPlanPattern DisplayString
  voipNumberPlanRule DisplayString
  voipNumberPlanRowStatus RowStatus

VoipDialPlanEntry  
SEQUENCE    
  voipDialPlanName DisplayString
  voipDialPlanPattern DisplayString
  voipDialPlanNumOfPrefixCut INTEGER
  voipDialPlanSipServer DisplayString
  voipDialPlanPrefixAddDigits DisplayString
  voipDialPlanNumberOfInterdigit INTEGER
  voipDialPlanInterdigitTimeout INTEGER
  voipDialPlanRowStatus RowStatus

VoipKeyPatternEntry  
SEQUENCE    
  voipKeyPatternName DisplayString
  voipKeyPatternServiceType INTEGER
  voipKeyPatternPattern DisplayString
  voipKeyPatternRowStatus RowStatus

VoipLocalHelpEntry  
SEQUENCE    
  voipLocalHelpName DisplayString
  voipLocalHelpIndex INTEGER
  voipLocalHelpTelNumber DisplayString
  voipLocalHelpRowStatus RowStatus

VoipIpSetEntry  
SEQUENCE    
  voipIpSetIp IpAddress
  voipIpSetVid VlanIndex
  voipIpSetMask INTEGER

VoipDnsEntry  
SEQUENCE    
  voipDnsIp IpAddress

VoipRouteEntry  
SEQUENCE    
  voipRouteSlot INTEGER
  voipRouteIp IpAddress
  voipRouteGateway IpAddress
  voipRouteMask INTEGER
  voipRouteMetric INTEGER
  voipRouteRowStatus RowStatus

VoipH248MgConfEntry  
SEQUENCE    
  voipH248MgConfSlot INTEGER
  voipH248MgConfName DisplayString
  voipH248MgConfEnable INTEGER
  voipH248MgConfH248Profile DisplayString
  voipH248MgConfPort INTEGER
  voipH248MgConfRowStatus RowStatus

VoipH248InterfaceConfEntry  
SEQUENCE    
  voipH248InterfaceConfId INTEGER
  voipH248InterfaceConfMgName DisplayString
  voipH248InterfaceConfMgEnable INTEGER
  voipH248InterfaceConfH248Profile DisplayString
  voipH248InterfaceConfPort INTEGER
  voipH248InterfaceConfIp IpAddress
  voipH248InterfaceConfMasklen INTEGER
  voipH248InterfaceConfVid VlanIndex
  voipH248InterfaceConfPrimary INTEGER
  voipH248InterfaceConfSecondary INTEGER
  voipH248InterfaceConfBhcaPeak INTEGER
  voipH248InterfaceConfBhcaAverage INTEGER

VoipH248SlotConfEntry  
SEQUENCE    
  voipH248SlotConfId INTEGER
  voipH248SlotConfMasterIp1 IpAddress
  voipH248SlotConfMasterIp2 IpAddress
  voipH248SlotConfOpmode INTEGER
  voipH248SlotConf8021pPrio INTEGER
  voipH248SlotConfPriorityDscp INTEGER

VoipH248SlaveConfEntry  
SEQUENCE    
  voipH248SlaveConfInterfaceId INTEGER
  voipH248SlaveConfSlaveId INTEGER
  voipH248SlaveConfSlaveIp IpAddress

VoipPotsRingEntry  
SEQUENCE    
  voipPotsRingConfId INTEGER
  voipPotsRingConfNameDefval INTEGER
  voipPotsRingConfName DisplayString
  voipPotsRingConfPatternDefval INTEGER
  voipPotsRingConfPatternOn1 INTEGER
  voipPotsRingConfPatternOff1 INTEGER
  voipPotsRingConfPatternOn2 INTEGER
  voipPotsRingConfPatternOff2 INTEGER
  voipPotsRingConfPatternOn3 INTEGER
  voipPotsRingConfPatternOff3 INTEGER

VoipInterfaceMapEntry  
SEQUENCE    
  voipIfIndex InterfaceIndex
  ifIndexValue InterfaceIndex

VoipIfEntry  
SEQUENCE    
  voipIfIndexValue InterfaceIndex

VoipExtH248InterfaceRouteEntry  
SEQUENCE    
  voipExtH248InterfaceRouteIp IpAddress
  voipExtH248InterfaceRouteGateway IpAddress
  voipExtH248InterfaceRouteMask INTEGER
  voipExtH248InterfaceRouteMetric INTEGER
  voipExtH248InterfaceRouteRowStatus RowStatus

VoipExtH248MediaStatEntry  
SEQUENCE    
  voipExtH248MediaStatSlotId INTEGER
  voipExtH248MediaStatPortCount INTEGER
  voipExtH248MediaStatState INTEGER

VoipExtH248TerminationStatEntry  
SEQUENCE    
  voipExtH248TerminationStatStateSlotId INTEGER
  voipExtH248TerminationStatStatePortNumber INTEGER
  voipExtH248TerminationStatName DisplayString
  voipExtH248TerminationStatPhoneState INTEGER
  voipExtH248TerminationStatCallServiceState INTEGER

VoipExtSipProfileEntry  
SEQUENCE    
  voipExtSipProfileName DisplayString
  voipExtSipProfileSipSvr DisplayString
  voipExtSipProfileRegSvr DisplayString
  voipExtSipProfileProxySvr DisplayString
  voipExtSipProfileSipPort INTEGER
  voipExtSipProfileRegSvrPort INTEGER
  voipExtSipProfileProxySvrPort INTEGER
  voipExtSipProfilePbit INTEGER
  voipExtSipProfileDscp INTEGER
  voipExtSipProfileKeepAlive INTEGER
  voipExtSipProfilePrack INTEGER
  voipExtSipProfileSe INTEGER
  voipExtSipProfileSwitchType INTEGER
  voipExtSipProfileRtpStartPort INTEGER
  voipExtSipProfileRtpEndPort INTEGER
  voipExtSipProfileRegistrationExpire INTEGER
  voipExtSipProfileRegistrationExpireTime INTEGER
  voipExtSipProfileRegistrationRetryTime INTEGER
  voipExtSipProfileRowStatus RowStatus
  voipExtSipProfilePrefixAddDigits DisplayString

VoipExtSipCallSvcProfileEntry  
SEQUENCE    
  voipExtSipCallSvcProfileName DisplayString
  voipExtSipCallSvcProfileKeypattern DisplayString
  voipExtSipCallSvcProfileDialPlanOn INTEGER
  voipExtSipCallSvcProfileDialPlanCc DisplayString
  voipExtSipCallSvcProfileDialPlanNdc DisplayString
  voipExtSipCallSvcProfileDialPlanTable DisplayString
  voipExtSipCallSvcProfileDndOn INTEGER
  voipExtSipCallSvcProfileDtmf INTEGER
  voipExtSipCallSvcProfileDtmfRfc2833Payload INTEGER
  voipExtSipCallSvcProfileCallWaitOn INTEGER
  voipExtSipCallSvcProfileClipOn INTEGER
  voipExtSipCallSvcProfileClirOn INTEGER
  voipExtSipCallSvcProfileCallTransferOn INTEGER
  voipExtSipCallSvcProfileCallConferenceOn INTEGER
  voipExtSipCallSvcProfileFax INTEGER
  voipExtSipCallSvcProfileFirstDigit INTEGER
  voipExtSipCallSvcProfileInterdigit INTEGER
  voipExtSipCallSvcProfileMatchdigit INTEGER
  voipExtSipCallSvcProfileFlash INTEGER
  voipExtSipCallSvcProfileFlashPattern DisplayString
  voipExtSipCallSvcProfileLocalCallOn INTEGER
  voipExtSipCallSvcProfileMWIOn INTEGER
  voipExtSipCallSvcProfileCentrexOn INTEGER
  voipExtSipCallSvcProfileRowStatus RowStatus

VoipExtSipCallSvcProfileLocalHelpEntry  
SEQUENCE    
  voipExtSipCallSvcProfileLocalHelpIndex INTEGER
  voipExtSipCallSvcProfileLocalHelpTableName DisplayString
  voipExtSipCallSvcProfileLocalHelpTableTel DisplayString

VoipExtDialPlanEntry  
SEQUENCE    
  voipExtDialPlanName DisplayString
  voipExtDialPlanIndex INTEGER
  voipExtDialPlanPattern DisplayString
  voipExtDialPlanRule DisplayString
  voipExtDialPlanRowStatus RowStatus

VoipExtSipRouteEntry  
SEQUENCE    
  voipExtSipRouteIp IpAddress
  voipExtSipRouteGateway IpAddress
  voipExtSipRouteMask INTEGER
  voipExtSipRouteMetric INTEGER
  voipExtSipRouteRowStatus RowStatus

VoipExtSipLineConfEntry  
SEQUENCE    
  voipExtSipLineConfHotlineOn INTEGER
  voipExtSipLineConfHotlineNo DisplayString
  voipExtSipLineConfHotlineTimeout INTEGER
  voipExtSipLineConfTax INTEGER

VoipExtSipLineStatusEntry  
SEQUENCE    
  voipExtSipLineStatusFxsStatus INTEGER
  voipExtSipLineStatusServiceStatus INTEGER
  voipExtSipLineStatusLocalcallStatus INTEGER

ImaGroupEntry  
SEQUENCE    
  imaGroupIndex INTEGER
  imaGroupClkMode INTEGER
  imaGroupVersion INTEGER

ImaGroupChanNumEntry  
SEQUENCE    
  imaGroupChanNumSlot INTEGER
  imaGroupChanNumMaximum INTEGER
  imaGroupChanNumCurrentTotal INTEGER
  imaGroupChanNumCurrentPvc INTEGER
  imaGroupChanNumCurrentDtpvc INTEGER

ImaGroupPvcEntry  
SEQUENCE    
  imaGroupPvcGroupIndex INTEGER
  imaGroupPvcVpi INTEGER
  imaGroupPvcVci INTEGER
  imaGroupPvcPvid VlanIndex
  imaGroupPvcEncap INTEGER
  imaGroupPvcPriority INTEGER
  imaGruopPvcProfile DisplayString
  imaGroupPvcRowStatus RowStatus
  imaGroupPvcEgressTag INTEGER

ImaGroupDtPvcEntry  
SEQUENCE    
  imaGroupDTPvcGroupIndex INTEGER
  imaGroupDtPvcVpi INTEGER
  imaGroupDtPvcVci INTEGER
  imaGroupDtPvcSvid VlanIndex
  imaGroupDtPvcCvid VlanIndex
  imaGroupDtPvcEncap INTEGER
  imaGroupDtPvcSPriority INTEGER
  imaGroupDtPvcCPriority INTEGER
  imaGroupDtPvcProfile DisplayString
  imaGroupDtPvcRowStatus RowStatus

ImaMgmtPvcEntry  
SEQUENCE    
  imaMgmtPvcGroupIndex INTEGER
  imaMgmtPvcVpi INTEGER
  imaMgmtPvcVci INTEGER
  imaMgmtPvcPvid VlanIndex
  imaMgmtPvcEncap INTEGER
  imaMgmtPvcPriority INTEGER
  imaMgmtPvcProfile DisplayString
  imaMgmtPvcRowStatus RowStatus
  imaMgmtPvcManagedIp IpAddress
  imaMgmtPvcGatewayIp IpAddress

Defined Values

zyxel 1.1.890
OBJECT IDENTIFIER    

products 1.1.890.1
OBJECT IDENTIFIER    

accessSwitch 1.1.890.1.5
OBJECT IDENTIFIER    

iesSeries 1.1.890.1.5.13
OBJECT IDENTIFIER    

ies5000 1.1.890.1.5.13.5
ZyXEL Private MIB
MODULE-IDENTITY    

ies5005 1.1.890.1.5.13.7
OBJECT IDENTIFIER    

ies6000 1.1.890.1.5.13.8
OBJECT IDENTIFIER    

acl 1.1.890.1.5.13.5.1
OBJECT IDENTIFIER    

alarmconf 1.1.890.1.5.13.5.2
OBJECT IDENTIFIER    

config 1.1.890.1.5.13.5.3
OBJECT IDENTIFIER    

diagnostic 1.1.890.1.5.13.5.4
OBJECT IDENTIFIER    

ipconf 1.1.890.1.5.13.5.5
OBJECT IDENTIFIER    

lcm 1.1.890.1.5.13.5.6
OBJECT IDENTIFIER    

multicast 1.1.890.1.5.13.5.7
OBJECT IDENTIFIER    

port 1.1.890.1.5.13.5.8
OBJECT IDENTIFIER    

profile 1.1.890.1.5.13.5.9
OBJECT IDENTIFIER    

switch 1.1.890.1.5.13.5.10
OBJECT IDENTIFIER    

sys 1.1.890.1.5.13.5.11
OBJECT IDENTIFIER    

trap 1.1.890.1.5.13.5.12
OBJECT IDENTIFIER    

statistics 1.1.890.1.5.13.5.13
OBJECT IDENTIFIER    

clear 1.1.890.1.5.13.5.14
OBJECT IDENTIFIER    

cluster 1.1.890.1.5.13.5.15
OBJECT IDENTIFIER    

voip 1.1.890.1.5.13.5.16
OBJECT IDENTIFIER    

ima 1.1.890.1.5.13.5.17
OBJECT IDENTIFIER    

dhcp 1.1.890.1.5.13.5.1.1
OBJECT IDENTIFIER    

dot1x 1.1.890.1.5.13.5.1.2
OBJECT IDENTIFIER    

macfilter 1.1.890.1.5.13.5.1.3
OBJECT IDENTIFIER    

pktfilter 1.1.890.1.5.13.5.1.4
OBJECT IDENTIFIER    

dhcpSnoop 1.1.890.1.5.13.5.1.5
OBJECT IDENTIFIER    

aclRule 1.1.890.1.5.13.5.1.6
OBJECT IDENTIFIER    

pppoeAgent 1.1.890.1.5.13.5.1.7
OBJECT IDENTIFIER    

dsBcast 1.1.890.1.5.13.5.1.8
OBJECT IDENTIFIER    

usBcast 1.1.890.1.5.13.5.1.9
OBJECT IDENTIFIER    

dscpMapping 1.1.890.1.5.13.5.1.10
OBJECT IDENTIFIER    

macAntiSpoofEnable 1.1.890.1.5.13.5.1.13
Enable/disable MAC anti-spoof.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

subnetvlan 1.1.890.1.5.13.5.1.14
OBJECT IDENTIFIER    

loopguard 1.1.890.1.5.13.5.1.15
OBJECT IDENTIFIER    

usStorm 1.1.890.1.5.13.5.1.16
OBJECT IDENTIFIER    

arpInspection 1.1.890.1.5.13.5.1.17
OBJECT IDENTIFIER    

macFF 1.1.890.1.5.13.5.1.18
OBJECT IDENTIFIER    

dhcpv6 1.1.890.1.5.13.5.1.19
OBJECT IDENTIFIER    

dhcpRelayEnable 1.1.890.1.5.13.5.1.1.1
Enable/disable DHCP relay Option82 function. Note that this object is obsolete in R1.03 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER auto(1), both(2), disable(3)  

dhcpRelay82Table 1.1.890.1.5.13.5.1.1.2
A table that contains DHCP Relay configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpRelay82Entry

dhcpRelay82Entry 1.1.890.1.5.13.5.1.1.2.1
The entry of DHCP Relay table.
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpRelay82Entry  

dhcpRelay82PrimaryServer 1.1.890.1.5.13.5.1.1.2.1.1
The IP address of the DHCP Relay primary server.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

dhcpRelay82SecondaryServer 1.1.890.1.5.13.5.1.1.2.1.2
The IP address of the DHCP Relay secondary server. This object is supported by R1.02 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

dhcpRelay82ActiveServer 1.1.890.1.5.13.5.1.1.2.1.3
The current active DHCP Relay server. This object is supported by R1.02 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER primary(1), secondary(2)  

dhcpRelay82Enable 1.1.890.1.5.13.5.1.1.2.1.4
Enable/disable DHCP relay and Option82 function. This object is supported by R1.03 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER relayEnable-option82Enable(1), relayDisable-option82Enable(2), disable(3)  

dhcpRelay82Info 1.1.890.1.5.13.5.1.1.2.1.5
User specific Option82 information. This object is supported by R1.03 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..23)  

dhcpRelay82RelayMode 1.1.890.1.5.13.5.1.1.2.1.6
DHCP relay mode. This object is supported by R1.03 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER auto(1), both(2)  

dhcpRelay82RowStatus 1.1.890.1.5.13.5.1.1.2.1.7
Row status of the table entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

dhcpRelay82Suboption2Enable 1.1.890.1.5.13.5.1.1.2.1.8
Enable/disable Option 82 sub-option 2. This object is supported by R3.00 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dhcpRelay82Suboption2Info 1.1.890.1.5.13.5.1.1.2.1.9
User specified information for Option 82 sub-option 2. This object is supported by R3.00 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

dhcpRelay82Option82Mode 1.1.890.1.5.13.5.1.1.2.1.10
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER private(1), tr101(2), tr101PlusVlanInfo(3)  

dhcpRelayInfo 1.1.890.1.5.13.5.1.1.3
User specific Option82 information. Note that this object is obsolete in R1.03 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..23)  

maxNumOfDhcpRelay82Conf 1.1.890.1.5.13.5.1.1.4
The maximum number of rows that can be created in dhcpRelay82Table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dhcpRelay82Delimiter 1.1.890.1.5.13.5.1.1.5
To configure the ASCII value of the delimiter character.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dhcpRelayOption82CheckEnable 1.1.890.1.5.13.5.1.1.6
Enable/disable system to check option82 in DHCP packets from DHCP server.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dot1xEnable 1.1.890.1.5.13.5.1.2.1
Enable/disable the 802.1x function.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

radiusServerTable 1.1.890.1.5.13.5.1.2.2
A table that contains Radius Server information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RadiusServerEntry

radiusServerEntry 1.1.890.1.5.13.5.1.2.2.1
The entry of Radius Server table.
Status: current Access: not-accessible
OBJECT-TYPE    
  RadiusServerEntry  

radiusServerIndex 1.1.890.1.5.13.5.1.2.2.1.1
The identity of the RADIUS server.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

radiusServerIp 1.1.890.1.5.13.5.1.2.2.1.2
The IP address of the Radius Server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

radiusServerPort 1.1.890.1.5.13.5.1.2.2.1.3
The UDP port of the Radius Server.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

radiusServerSecret 1.1.890.1.5.13.5.1.2.2.1.4
The shared secret of the Radius Server.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

dot1xPortTable 1.1.890.1.5.13.5.1.2.3
This table includes 802.1x port configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Dot1xPortEntry

dot1xPortEntry 1.1.890.1.5.13.5.1.2.3.1
An entry in dot1xPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Dot1xPortEntry  

dot1xPortEnable 1.1.890.1.5.13.5.1.2.3.1.1
Enable/disable 802.1x for the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dot1xPortControl 1.1.890.1.5.13.5.1.2.3.1.2
The object defines the 802.1x control type for the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER auto(1), forceAuth(2), forceUnAuth(3)  

dot1xPortReAuthEnable 1.1.890.1.5.13.5.1.2.3.1.3
Enable/disable 802.1x re-authentication for the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dot1xPortReAuthPeriod 1.1.890.1.5.13.5.1.2.3.1.4
The object defines the 802.1x re-authentication period for the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 60..65535  

dot1xBatchSet 1.1.890.1.5.13.5.1.2.4
OBJECT IDENTIFIER    

dot1xTarget 1.1.890.1.5.13.5.1.2.4.1
This managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 Byte 2~4: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8, and the second octet specifying slots 9 through 16, and so on. Byte 5~: each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

dot1xOps 1.1.890.1.5.13.5.1.2.4.2
The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: enable dot1x BIT 2: disable dot1x BIT 3: set dot1x control to be auto BIT 4: set dot1x control to be forceAuth BIT 5: set dot1x control to be forceUnAuth BIT 6: enable dot1x re-authentication BIT 7: disable dot1x re-authentication BIT 8: set dot1x re-authentication period.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dot1xReAuthPeriodForBatchSet 1.1.890.1.5.13.5.1.2.4.3
The object defines the 802.1x re-authentication period for batch setting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 60..65535  

macFilterPortTable 1.1.890.1.5.13.5.1.3.1
This table includes the status of mac filtering for each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFilterPortEntry

macFilterPortEntry 1.1.890.1.5.13.5.1.3.1.1
An entry in macFilterPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFilterPortEntry  

macFilterPortEnable 1.1.890.1.5.13.5.1.3.1.1.1
Enable/disable MAC filtering for the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enableMacFilter(1), enableMacCount(2), enableOuiFilter(3), disable(4)  

macFilterPortMacCount 1.1.890.1.5.13.5.1.3.1.1.2
The total number of MAC addresses allowed for the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

macFilterPortFilterMode 1.1.890.1.5.13.5.1.3.1.1.3
The mac filter mode (accept or deny) for the port. This object is supported by R1.02 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER accept(1), deny(2)  

maxNumOfMacFiltersInSystem 1.1.890.1.5.13.5.1.3.2
The max number of mac filters supported in the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

maxNumOfMacFiltersPerPort 1.1.890.1.5.13.5.1.3.3
The max number of mac filters supported per port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

currNumOfMacFiltersInSystem 1.1.890.1.5.13.5.1.3.4
The current number of mac filters in the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macFilterTable 1.1.890.1.5.13.5.1.3.5
A table that contains the mac filter addresses.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFilterEntry

macFilterEntry 1.1.890.1.5.13.5.1.3.5.1
The entry of macFilterTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFilterEntry  

macFilterAddr 1.1.890.1.5.13.5.1.3.5.1.1
The mac address which can pass through or be rejected from the port.
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

macFilterRowStatus 1.1.890.1.5.13.5.1.3.5.1.2
The row status of the entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

macfilterBatchSet 1.1.890.1.5.13.5.1.3.6
OBJECT IDENTIFIER    

macfilterTarget 1.1.890.1.5.13.5.1.3.6.1
This managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 Byte 2~4: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8, and the second octet specifying slots 9 through 16, and so on. Byte 5~: each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

macfilterOps 1.1.890.1.5.13.5.1.3.6.2
The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: enable mac filter BIT 2: enable mac count filter BIT 3: disable mac filter BIT 4: set mac count.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

macFilterMacCountForBatchSet 1.1.890.1.5.13.5.1.3.6.3
The total number of MAC addresses allowed for a port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..128  

ouiFilterTable 1.1.890.1.5.13.5.1.3.7
A table that contains the OUI filter addresses.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    OuiFilterEntry

ouiFilterEntry 1.1.890.1.5.13.5.1.3.7.1
The entry of ouiFilterTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  OuiFilterEntry  

ouiFilterAddr 1.1.890.1.5.13.5.1.3.7.1.1
The first three bytes of the mac address which can pass through or be rejected from the port.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ouiFilterRowStatus 1.1.890.1.5.13.5.1.3.7.1.2
The row status of the entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

maxNumOfOuiFiltersPerPort 1.1.890.1.5.13.5.1.3.8
The max number of OUI filters supported per port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macFilterStatusTable 1.1.890.1.5.13.5.1.3.9
A table that contains the mac filter addresses.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFilterStatusEntry

macFilterStatusEntry 1.1.890.1.5.13.5.1.3.9.1
The entry of macFilterStatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFilterStatusEntry  

macFilterStatusId 1.1.890.1.5.13.5.1.3.9.1.1
The index of the entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macFilterStatusAddr 1.1.890.1.5.13.5.1.3.9.1.2
The mac address which can pass through or be rejected from the port.
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

macFilterPerPVCTable 1.1.890.1.5.13.5.1.3.10
A table for per-PVC macfilter configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFilterPerPVCEntry

macFilterPerPVCEntry 1.1.890.1.5.13.5.1.3.10.1
The entry of macFilterPerPVCTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFilterPerPVCEntry  

macFilterPerPVCVpi 1.1.890.1.5.13.5.1.3.10.1.1
VPI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

macFilterPerPVCVci 1.1.890.1.5.13.5.1.3.10.1.2
VCI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

macFilterPerPVCEnable 1.1.890.1.5.13.5.1.3.10.1.3
Enable/disable MAC filtering for the port-vpi/vci
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enablePvcMacFilter(1), enablePvcMacCount(2), disable(3)  

macFilterPerPVCMode 1.1.890.1.5.13.5.1.3.10.1.4
The mac filter mode (accept or deny) for the port-vpi/vci.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER accept(1), deny(2)  

macFilterPerPVCMacCount 1.1.890.1.5.13.5.1.3.10.1.5
The total number of MAC addresses allowed for the port-vpi/vci.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

macFilterPerPVCMACTable 1.1.890.1.5.13.5.1.3.11
A table for per-PVC macfilter configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFilterPerPVCMACEntry

macFilterPerPVCMACEntry 1.1.890.1.5.13.5.1.3.11.1
The entry of macFilterPerPVCMACTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFilterPerPVCMACEntry  

macFilterPerPVCMACVpi 1.1.890.1.5.13.5.1.3.11.1.1
VPI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

macFilterPerPVCMACVci 1.1.890.1.5.13.5.1.3.11.1.2
VCI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

macFilterPerPVCMACAddr 1.1.890.1.5.13.5.1.3.11.1.3
The mac address which can pass through or be rejected from the port-vpi/vci
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

macFilterPerPVCMACRowStatus 1.1.890.1.5.13.5.1.3.11.1.4
The row status of the entry.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

pktFilterPortTable 1.1.890.1.5.13.5.1.4.1
This table includes packet filtering for each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PktFilterPortEntry

pktFilterPortEntry 1.1.890.1.5.13.5.1.4.1.1
An entry in pktFilterPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PktFilterPortEntry  

pktFilter 1.1.890.1.5.13.5.1.4.1.1.1
The packet filter. The semantic for each bit is: BIT 1: accept all BIT 2: accept PPPoE only BIT 3: reject ARP BIT 4: reject DHCP BIT 5: reject EAPOL BIT 6: reject PPPoE BIT 7: reject NetBIOS BIT 8: reject IGMP BIT 9: reject IP
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

pktfilterBatchSet 1.1.890.1.5.13.5.1.4.2
OBJECT IDENTIFIER    

pktfilterTarget 1.1.890.1.5.13.5.1.4.2.1
This managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 Byte 2~4: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8, and the second octet specifying slots 9 through 16, and so on. Byte 5~: each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

pktfilterOps 1.1.890.1.5.13.5.1.4.2.2
The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: set packet filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

pktfilterForBatchSet 1.1.890.1.5.13.5.1.4.2.3
The packet filter for batch setting. The semantic for each bit is identical to the object pktFilter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

pktFilterPerPVCTable 1.1.890.1.5.13.5.1.4.3
This table includes per-PVC packet filter configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PktFilterPerPVCEntry

pktFilterPerPVCEntry 1.1.890.1.5.13.5.1.4.3.1
An entry in pktFilterPerPVCTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PktFilterPerPVCEntry  

pktFilterPerPVCVpi 1.1.890.1.5.13.5.1.4.3.1.1
VPI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

pktFilterPerPVCVci 1.1.890.1.5.13.5.1.4.3.1.2
VCI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

pktFilterPerPVCpktFilter 1.1.890.1.5.13.5.1.4.3.1.3
The packet filter. The semantic for each bit is: BIT 1: accept all BIT 2: accept PPPoE only BIT 3: reject ARP BIT 4: reject DHCP BIT 5: reject EAPOL BIT 6: reject PPPoE BIT 7: reject NetBIOS BIT 8: reject IGMP BIT 9: reject IP
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dhcpSnoopPortTable 1.1.890.1.5.13.5.1.5.1
This table includes DHCP snooping enable/disable for each port. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpSnoopPortEntry

dhcpSnoopPortEntry 1.1.890.1.5.13.5.1.5.1.1
An entry of dhcpSnoopPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpSnoopPortEntry  

dhcpSnoopEnable 1.1.890.1.5.13.5.1.5.1.1.1
Enable/disable DHCP snooping for a port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dhcpSnoopTarget 1.1.890.1.5.13.5.1.5.2
This managed object is used for identify the target on which the operation should be performed. The target is encoded as: Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 Byte 2~4: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8, and the second octet specifying slots 9 through 16, and so on. Byte 5~: each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

dhcpSnoopOps 1.1.890.1.5.13.5.1.5.3
The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: DHCP snooping table flush.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dhcpStaticTable 1.1.890.1.5.13.5.1.5.4
This table defines DHCP static IP addresses. This table is supported by R1.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpStaticEntry

dhcpStaticEntry 1.1.890.1.5.13.5.1.5.4.1
An entry of dhcpStaticTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpStaticEntry  

dhcpStaticIpAddr 1.1.890.1.5.13.5.1.5.4.1.1
The IP address which can pass through the port.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpStaticRowStatus 1.1.890.1.5.13.5.1.5.4.1.2
Row status of the table entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

maxNumOfDhcpStaticIp 1.1.890.1.5.13.5.1.5.5
The maximum number of DHCP static IP addresses which can be created for a port. This object is supported by R1.03 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dhcpSnoopLan2lanTable 1.1.890.1.5.13.5.1.5.6
Support DHCP lan2lan to prevent DHCP service hack if customer installed DHCP server in its subscriber network. This table is supported by R5.05 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpSnoopLan2lanEntry

dhcpSnoopLan2lanEntry 1.1.890.1.5.13.5.1.5.6.1
The entry of dhcpSnoopLan2lanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpSnoopLan2lanEntry  

dhcpSnoopLan2lanEnable 1.1.890.1.5.13.5.1.5.6.1.1
Enable/disable DHCP server on subscriber port
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

aclSetTable 1.1.890.1.5.13.5.1.6.1
This table is supported by R1.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AclSetEntry

aclSetEntry 1.1.890.1.5.13.5.1.6.1.1
An entry of aclSetTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AclSetEntry  

aclSetVpi 1.1.890.1.5.13.5.1.6.1.1.1
VPI value.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

aclSetVci 1.1.890.1.5.13.5.1.6.1.1.2
VCI value.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

aclSetProfileName 1.1.890.1.5.13.5.1.6.1.1.3
ACL Profile name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

aclSetRowStatus 1.1.890.1.5.13.5.1.6.1.1.4
RowStatus of aclSetEntry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

aclNoMatchTable 1.1.890.1.5.13.5.1.6.2
This table is supported by R5.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AclNoMatchEntry

aclNoMatchEntry 1.1.890.1.5.13.5.1.6.2.1
An entry of aclNoMatchTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AclNoMatchEntry  

aclNoMatchAction 1.1.890.1.5.13.5.1.6.2.1.1
Pass or drop the packet.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER accept(1), deny(2)  

pppoeAgentTable 1.1.890.1.5.13.5.1.7.1
A table that contains PPPoE DHCP Relay configuration. This table is supported by R1.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PppoeAgentEntry

pppoeAgentEntry 1.1.890.1.5.13.5.1.7.1.1
An entry of pppoeAgentTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PppoeAgentEntry  

pppoeAgentEnable 1.1.890.1.5.13.5.1.7.1.1.1
Enable/disable DHCP relay and Option82 function.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

pppoeAgentInfo 1.1.890.1.5.13.5.1.7.1.1.2
User specific Option82 information.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..23)  

pppoeAgentRowStatus 1.1.890.1.5.13.5.1.7.1.1.3
Row status of the table entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

pppoeAgentOptionMode 1.1.890.1.5.13.5.1.7.1.1.4
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER private(1), tr101(2), tr101PlusVlanInfo(3)  

maxNumOfPppoeDhcpRelay82Conf 1.1.890.1.5.13.5.1.7.2
The maximum number of rows that can be created in pppoeAgentTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

pppoeAgentDelimiter 1.1.890.1.5.13.5.1.7.3
To configure the ASCII value of the delimiter character.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dsBcastTable 1.1.890.1.5.13.5.1.8.1
A table that contains downstream broadcast forbidden configuration. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DsBcastEntry

dsBcastEntry 1.1.890.1.5.13.5.1.8.1.1
An entry of dsBcastTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DsBcastEntry  

dsBcastRowStatus 1.1.890.1.5.13.5.1.8.1.1.1
Row status of the table entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usBcastCtrlEnable 1.1.890.1.5.13.5.1.9.1
Enable/disable upstream broadcast control.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

usBcastCtrlRate 1.1.890.1.5.13.5.1.9.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dscpMappingTable 1.1.890.1.5.13.5.1.10.1
The table contains DSCP mapping configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DscpMappingEntry

dscpMappingEntry 1.1.890.1.5.13.5.1.10.1.1
An entry of dscpMappingTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DscpMappingEntry  

dscpMappingSrcCodePoint 1.1.890.1.5.13.5.1.10.1.1.1
The DSCP source code point used for mapping.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dscpMappingMapPriority 1.1.890.1.5.13.5.1.10.1.1.2
The mapping p bits that will replace the source p bits in the incoming packet.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

dscpPortTable 1.1.890.1.5.13.5.1.10.2
The table contains DSCP port configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DscpPortEntry

dscpPortEntry 1.1.890.1.5.13.5.1.10.2.1
An entry of dscpPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DscpPortEntry  

dscpPortEnable 1.1.890.1.5.13.5.1.10.2.1.1
Enable/disable DSCP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

subnetvlanStatus 1.1.890.1.5.13.5.1.14.1
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

subnetvlanTable 1.1.890.1.5.13.5.1.14.2
A table that contains subnet vlan configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SubnetvlanEntry

subnetvlanEntry 1.1.890.1.5.13.5.1.14.2.1
The entry of subnet vlan table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SubnetvlanEntry  

subnetvlanIp 1.1.890.1.5.13.5.1.14.2.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

subnetvlanMask 1.1.890.1.5.13.5.1.14.2.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

subnetvlanVid 1.1.890.1.5.13.5.1.14.2.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4094  

subnetvlanPriority 1.1.890.1.5.13.5.1.14.2.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..7  

subnetvlanName 1.1.890.1.5.13.5.1.14.2.1.5
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

subnetvlanRowStatus 1.1.890.1.5.13.5.1.14.2.1.6
Row status of the table entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

subnetvlanInetTable 1.1.890.1.5.13.5.1.14.3
A table that contains IPv4/IPv6 subnet vlan configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SubnetvlanInetEntry

subnetvlanInetEntry 1.1.890.1.5.13.5.1.14.3.1
The entry of subnet vlan inet table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SubnetvlanInetEntry  

subnetvlanInetAddrType 1.1.890.1.5.13.5.1.14.3.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

subnetvlanInetAddr 1.1.890.1.5.13.5.1.14.3.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

subnetvlanInetMask 1.1.890.1.5.13.5.1.14.3.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

subnetvlanInetVid 1.1.890.1.5.13.5.1.14.3.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4094  

subnetvlanInetPriority 1.1.890.1.5.13.5.1.14.3.1.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..7  

subnetvlanInetName 1.1.890.1.5.13.5.1.14.3.1.6
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

subnetvlanInetRowStatus 1.1.890.1.5.13.5.1.14.3.1.7
Row status of the table entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

loopguardTable 1.1.890.1.5.13.5.1.15.1
A table that contains Loopguard configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LoopguardEntry

loopguardEntry 1.1.890.1.5.13.5.1.15.1.1
The entry of Loopguard table.
Status: current Access: not-accessible
OBJECT-TYPE    
  LoopguardEntry  

loopguardStatus 1.1.890.1.5.13.5.1.15.1.1.1
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

loopguardMode 1.1.890.1.5.13.5.1.15.1.1.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fix(0), dynamic(1)  

loopguardRecoverTime 1.1.890.1.5.13.5.1.15.1.1.3
seconds
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 60..600  

usStormTable 1.1.890.1.5.13.5.1.16.1
A table that contains UsStorm configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsStormEntry

usStormEntry 1.1.890.1.5.13.5.1.16.1.1
The entry of UsStorm table.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsStormEntry  

usStormBcastThresh 1.1.890.1.5.13.5.1.16.1.1.1
0~1488096 pkt/s, -1 means no limit
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

usStormMcastThresh 1.1.890.1.5.13.5.1.16.1.1.2
0~1488096 pkt/s, -1 means no limit
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

usStormUcastThresh 1.1.890.1.5.13.5.1.16.1.1.3
0~1488096 pkt/s, -1 means no limit
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

arpInspectionTable 1.1.890.1.5.13.5.1.17.1
Support ARP inspection to filter unauthorized ARP packets on the network. This can prevent many kinds of man-in-the-middle attacks. This table is supported by R5.05 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ArpInspectionEntry

arpInspectionEntry 1.1.890.1.5.13.5.1.17.1.1
The entry of arpInspectionTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ArpInspectionEntry  

arpInspectionEnable 1.1.890.1.5.13.5.1.17.1.1.1
Enable/disable arp inspection on the specified subscriber port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

macFFStaticTable 1.1.890.1.5.13.5.1.18.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFFStaticEntry

macFFStaticEntry 1.1.890.1.5.13.5.1.18.1.1
The entry of macFFStaticTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFFStaticEntry  

macFFStaticIndex 1.1.890.1.5.13.5.1.18.1.1.1
The macFF static entry index 1 ~ 24
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macFFStaticSrcIP 1.1.890.1.5.13.5.1.18.1.1.2
Matched range for static subscriber's IP in ARP request
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

macFFStaticMask 1.1.890.1.5.13.5.1.18.1.1.3
Matched range for static subscriber's IP in ARP request
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

macFFStaticArasIP 1.1.890.1.5.13.5.1.18.1.1.4
IP of static macFF Access Router/App Server
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

macFFStaticVid 1.1.890.1.5.13.5.1.18.1.1.5
vlan ID of macFF Access Router/App Server
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

macFFStaticRowStatus 1.1.890.1.5.13.5.1.18.1.1.6
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

macFFDynamicTable 1.1.890.1.5.13.5.1.18.2
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFFDynamicEntry

macFFDynamicEntry 1.1.890.1.5.13.5.1.18.2.1
The entry of macFFDynamicTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFFDynamicEntry  

macFFDynamicIndex 1.1.890.1.5.13.5.1.18.2.1.1
The macFF entry index 1 ~ 24
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macFFDynamicSrcIP 1.1.890.1.5.13.5.1.18.2.1.2
Matched range for dynamic subscriber's IP in ARP request
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

macFFDynamicMask 1.1.890.1.5.13.5.1.18.2.1.3
Matched range for dynamic subscriber's IP in ARP request
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macFFDynamicArasIP 1.1.890.1.5.13.5.1.18.2.1.4
IP of dynamic macFF Access Router/App Server
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

macFFDynamicVid 1.1.890.1.5.13.5.1.18.2.1.5
vlan ID of macFF Access Router/App Server
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4094  

macFFVlanTable 1.1.890.1.5.13.5.1.18.3
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFFVlanEntry

macFFVlanEntry 1.1.890.1.5.13.5.1.18.3.1
The entry of macFFVlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFFVlanEntry  

macFFVlanVid 1.1.890.1.5.13.5.1.18.3.1.1
Vlan ID of macFF Access Router/App Server
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4094  

macFFVlanRowStatus 1.1.890.1.5.13.5.1.18.3.1.2
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

macFFFlush 1.1.890.1.5.13.5.1.18.4
Set the object to n to flush the slot n's macff arp table(not include the MSC slot). macFFArpStatusUplinkTable(1.3.6.1.4.1.890.1.5.13.5.13.23.1) macFFArpStatusSlotTable(1.3.6.1.4.1.890.1.5.13.5.13.23.2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dhcpv6RelayTable 1.1.890.1.5.13.5.1.19.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Dhcpv6RelayEntry

dhcpv6RelayEntry 1.1.890.1.5.13.5.1.19.1.1
The entry of dhcpv6RelayTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Dhcpv6RelayEntry  

dhcpv6RelayLdraState 1.1.890.1.5.13.5.1.19.1.1.1
Enable/disable DHCPv6 LDRA function
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dhcpv6RelayRowStatus 1.1.890.1.5.13.5.1.19.1.1.2
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

dhcpv6RelayOptionTable 1.1.890.1.5.13.5.1.19.2
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Dhcpv6RelayOptionEntry

dhcpv6RelayOptionEntry 1.1.890.1.5.13.5.1.19.2.1
The entry of dhcpv6RelayOptionTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Dhcpv6RelayOptionEntry  

dhcpv6RelayOptionId 1.1.890.1.5.13.5.1.19.2.1.1
DHCPv6 option ID
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER interfaceId(18), remoteId(37)  

dhcpv6RelayOptionState 1.1.890.1.5.13.5.1.19.2.1.2
Enable/disable DHCPv6 option
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dhcpv6RelayOptionFormat 1.1.890.1.5.13.5.1.19.2.1.3
User specific Option format '%' treated as a beginner of predefined runtime variable the rule is below: %%: equals character % %0x00~0xFF: represents byte value %pname: configured port name %ptel: configured port tel %pid: port index %chvpi: channel vpi %chvci: channel vci %slotid: slot index of the logic port %svlan: SVLAN ID which DHCP client runs on %cvlan: CVLAN ID which DHCP client runs on %hname: host device name %cmac: MAC address of client, represents as Byte %phtype: ATM: 'atm' Ethernet 'eth' %blank: blank character
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

alarmOps 1.1.890.1.5.13.5.2.1
The manager sets the corresponding bit value to 1 to start the operation and the agent clears the object to zero when the operation is successfully completed. The various bit positions are: BIT 1: clear BIT 2: cutoff BIT 3: clear alarm history table
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

alarmConfTable 1.1.890.1.5.13.5.2.2
This table includes alarm configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlarmConfEntry

alarmConfEntry 1.1.890.1.5.13.5.2.2.1
An entry in alarmConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AlarmConfEntry  

alarmConfId 1.1.890.1.5.13.5.2.2.1.1
3: dslLineUp 4: dslLineDown 7: dslLineLdmStart 8: dslLineLdmDone 9: dslLinePowerDownL2 10:dslLinePowerDownL0 11:dslLineFailure 14:adslPerfLolThresh 17:adslPerfLofThresh 18:adslPerfLosThresh 19:adslPerfLprThresh 20:adslPerfESThresh 21:adslRateChange 22:adslPerfSESThresh 23:adslPerfUASThresh 24:shdslLoopAttenCrossing 25:shdslSNRMarginCrossing 26:shdslPerfESThresh 27:shdslPerfSESThresh 28:shdslPerfCRCAnomaliesThresh 29:shdslPerfLOSWSThresh 30:shdslPerfUASThresh 31:vdslPerfLolThresh 32:vdslPerfLofThresh 33:vdslPerfLosThresh 34:vdslPerfLprThresh 35:vdslPerfESThresh 36:vdslPerfSESThresh 37:vdslPerfUASThresh 38:dslMacAntiSpoofing 39:vdslPerfCodeViolationThresh 40:vdslVturInfoReady 41:vdslPerfRateChange 42:vdslTCACorrect 43:vdslTCAFailinit 44:vdslTCAFEC 45:vdslStatusChange 46:lineLoopGuard 1001:eqpt48VPowerFailure 1002:eqptVoltageError 1003:eqptTempError 1004:eqptFanError 1005:eqptTempLowFanStop 1009:eqptHWMonitorFailre 1011:eqptColdStart 1012:eqptWarmStart 1019:eqptMgmtPortUp 1020:eqptMgmtPortDown 1021:eqptExternalAlarmInput 1022:eqptTopologyChange 1023:eqptFWUploadOK 1024:eqptFWUploadFailure 1025:eqptLTPlugIn 1026:eqptLTPullOut 1028:eqptLTDslDeviceFailure 1029:eqptLTDslDeviceRedownload 1031:eqptLTActive 1032:eqptLTInactive 1038:eqptLTFWUploadOK 1039:eqptLTFWUploadFailure 1040:eqptLTEnable 1041:eqptLTDisable 1042:eqptLTReset 1043:eqptNTSwitchOK 1044:eqptCpuUtilizationHigh 1045:eqptVopBatteryFailure 1046:eqptVopClockFailure 1047:eqptVopRingerFault 1048:eqptPacketBufferUsageHigh 1049:eqptMemoryUsageHigh 1050:eqptStpNewRoot 1053:eqptStpPortStateChange 1054:eqptStpPortRoleChange 2001:sysReboot 2002:sysConfigChange 2003:sysConfigUploadOK 2004:sysConfigUploadFailure 2005:sysTimeSyncFailure 2006:sysAlarmCutoffEnable 2007:sysAlarmClearEnable 2008:sysLoginFailure 2009:sysLogin 2010:sysAccountAdded 2011:sysAccountDeleted 2012:sysAccountModified 2013:sysSvrSyncProfOk 2014:sysSvrSyncProfFail 2015:sysCliSyncProfOk 2016:sysCliSyncProfFail 2017:sysMacAntiSpoofing 2018:sysClusterMemberActive 2019:sysClusterMemberInactive 2020:sysClusterMemeberAdded 2021:sysClusterMemeberDeleted 2022:pingProbeFailed 2023:pingTestFailed 2024:pingTestCompleted 2025:traceRouteTestFailed 2026:traceRouteTestCompleted 3006:enetUp 3007:enetDown 3008:enetLoopGuard 3009:enetSFPError 3010:enetSFPTxEnable 3011:enetSFPTxDisable 4001:vopTempError 4002:vopDCPowerFailure 4003:vopACPowerFailure 4004:vopRingTimerFailure 4005:vopRingResourceFailure 4006:vopRingOhdFailure 4007:vopNoFreeDSPChannel 4008:vopMCMissing 4009:vopSCMissing 4010:vopTermNameDup 4011:vopNoProtection 4012:vopProtectionSwitch 4013:vopDropCall 4014:vopBatteryFail 4015:vopClockFail 4016:vopRingerFail 4017:vopMgcMissing 4018:vopMgEnable 4019:vopMgDisable 5001:cfmError 5003:lldpRemoteChange 6001: imaAlarmGroupStartupFe 6002: imaAlarmGroupCfgAbort 6003: imaAlarmGroupCfgAbortFe 6004: imaAlarmGroupInsuffLinks 6005: imaAlarmGroupInsuffLinksFe 6006: imaAlarmGroupBlockedFe 6007: imaAlarmGroupTimingSynch 6008: imaAlarmLinkLif 6009: imaAlarmLinkLods 6010: imaAlarmLinkRfi 6011: imaAlarmLinkTxMisConnect 6012: imaAlarmLinkRxMisConnect 6013: imaAlarmLinkTxFault 6014: imaAlarmLinkRxFault 6015: imaAlarmLinkTxUnusableFe 6016: imaAlarmLinkRxUnusableFe 7001: e1AlarmLinkLOS 7002: e1AlarmPathLOF 7003: e1AlarmPathAIS 7004: e1AlarmPathRDI 7005: e1AlarmPathOCASMF 7006: e1AlarmPathOCRCMF 7007: e1AlarmLinkSF 7008: e1AlarmLinkSD 7009: e1AlarmTCAQuarterES 7010: e1AlarmTCAQuarterSES 7011: e1AlarmTCAQuarterUAS 7012: e1AlarmTCADayES 7013: e1AlarmTCADaySES 7014: e1AlarmTCADayUAS
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmConfFacility 1.1.890.1.5.13.5.2.2.1.2
Alarm facility.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER local1(0), local1(1), local2(2), local3(3), local4(4), local5(5), local6(6), local7(7)  

alarmConfTarget 1.1.890.1.5.13.5.2.2.1.3
The destination which alarms are reported to. Set the bit to 1 to enable the target. BIT 1: snmp trap BIT 2: syslog
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

alarmConfSeverity 1.1.890.1.5.13.5.2.2.1.4
Alarm severity
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER critical(1), major(2), minor(3), info(4)  

alarmConfClearable 1.1.890.1.5.13.5.2.2.1.5
Setting the object to one indicates that the alarm is to be cleared when user submits alarm clear.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER clearable(1), unclearable(2)  

alarmCurrTable 1.1.890.1.5.13.5.2.3
This table includes current alarm information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlarmCurrEntry

alarmCurrEntry 1.1.890.1.5.13.5.2.3.1
An entry in alarmCurrTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AlarmCurrEntry  

alarmCurrIndex 1.1.890.1.5.13.5.2.3.1.1
Index of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmCurrOccurTime 1.1.890.1.5.13.5.2.3.1.2
Alarm occurence time (in hundredths of a second) since the system was last re-initialized.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

alarmCurrTrapOid 1.1.890.1.5.13.5.2.3.1.3
Trap OID of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

alarmCurrParam1 1.1.890.1.5.13.5.2.3.1.4
The 1st parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmCurrParam2 1.1.890.1.5.13.5.2.3.1.5
The 2nd parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmCurrParam3 1.1.890.1.5.13.5.2.3.1.6
The 3rd parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmCurrParam4 1.1.890.1.5.13.5.2.3.1.7
The 4th parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmCurrParam5 1.1.890.1.5.13.5.2.3.1.8
The 5th parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmCurrParam6 1.1.890.1.5.13.5.2.3.1.9
The 6th parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmCurrParam7 1.1.890.1.5.13.5.2.3.1.10
The 7th parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmCurrParam8 1.1.890.1.5.13.5.2.3.1.11
The 8th parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmCurrTimeDescr 1.1.890.1.5.13.5.2.3.1.12
The string representation of occurence time (YYYY/MM/DD HH:MM:SS).
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

alarmCurrSeverity 1.1.890.1.5.13.5.2.3.1.13
The severity of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER critical(1), major(2), minor(3), info(4)  

alarmCurrDescr 1.1.890.1.5.13.5.2.3.1.14
The description of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

alarmSeverityPortTable 1.1.890.1.5.13.5.2.4
This table includes the configuration of alarm reporting severity threshold for each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlarmSeverityPortEntry

alarmSeverityPortEntry 1.1.890.1.5.13.5.2.4.1
An entry in alarmSeverityPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AlarmSeverityPortEntry  

severityThresh 1.1.890.1.5.13.5.2.4.1.1
The minimum alarm severity that is reported.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER critical(1), major(2), minor(3), info(4)  

externalAlarmTable 1.1.890.1.5.13.5.2.5
This table includes the configuration of external alarms.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ExternalAlarmEntry

externalAlarmEntry 1.1.890.1.5.13.5.2.5.1
An entry in externalAlarmTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ExternalAlarmEntry  

externalAlarmIndex 1.1.890.1.5.13.5.2.5.1.1
The external alarm index.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

externalAlarmName 1.1.890.1.5.13.5.2.5.1.2
The external alarm name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

alarmTarget 1.1.890.1.5.13.5.2.6
The manager sets the corresponding bit value to 1 to start the operation and the agent clears the object to zero when the operation is successfully completed. The various bit positions are: BIT 1: clear BIT 2: cutoff
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

alarmHisTable 1.1.890.1.5.13.5.2.7
This table that contains alarm history data. This table is supported by R5.05 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AlarmHisEntry

alarmHisEntry 1.1.890.1.5.13.5.2.7.1
An entry in alarmHisTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AlarmHisEntry  

alarmHisIndex 1.1.890.1.5.13.5.2.7.1.1
Index of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmHisOccurTime 1.1.890.1.5.13.5.2.7.1.2
Alarm occurence time (in hundredths of a second) since the system was last re-initialized.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

alarmHisTrapOid 1.1.890.1.5.13.5.2.7.1.3
Trap OID of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

alarmHisParam1 1.1.890.1.5.13.5.2.7.1.4
The 1st parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmHisParam2 1.1.890.1.5.13.5.2.7.1.5
The 2nd parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmHisParam3 1.1.890.1.5.13.5.2.7.1.6
The 3rd parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmHisParam4 1.1.890.1.5.13.5.2.7.1.7
The 4th parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmHisParam5 1.1.890.1.5.13.5.2.7.1.8
The 5th parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmHisParam6 1.1.890.1.5.13.5.2.7.1.9
The 6th parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmHisParam7 1.1.890.1.5.13.5.2.7.1.10
The 7th parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmHisParam8 1.1.890.1.5.13.5.2.7.1.11
The 8th parameter of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

alarmHisTimeDescr 1.1.890.1.5.13.5.2.7.1.12
The string representation of occurence time (YYYY/MM/DD HH:MM:SS).
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

alarmHisSeverity 1.1.890.1.5.13.5.2.7.1.13
The severity of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER critical(1), major(2), minor(3), info(4)  

alarmHisDescr 1.1.890.1.5.13.5.2.7.1.14
The description of the alarm.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

alarmHisFilter 1.1.890.1.5.13.5.2.8
OBJECT IDENTIFIER    

alarmHisFilterByIfIndex 1.1.890.1.5.13.5.2.8.1
ifIndex Filter for alarmHisTable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

configOps 1.1.890.1.5.13.5.3.1
The manager sets the corresponding bit value to 1 to start the operation and the agent clears the object to zero when the operation is successfully completed. The various bit positions are: BIT 1: config save BIT 2: factory default
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

loopback 1.1.890.1.5.13.5.4.1
OBJECT IDENTIFIER    

ldm 1.1.890.1.5.13.5.4.2
OBJECT IDENTIFIER    

selt 1.1.890.1.5.13.5.4.3
OBJECT IDENTIFIER    

mlt 1.1.890.1.5.13.5.4.4
OBJECT IDENTIFIER    

oamloopback 1.1.890.1.5.13.5.4.5
OBJECT IDENTIFIER    

vdslldm 1.1.890.1.5.13.5.4.6
OBJECT IDENTIFIER    

imaOamF5Loopback 1.1.890.1.5.13.5.4.7
OBJECT IDENTIFIER    

xdsl2ExtStatus 1.1.890.1.5.13.5.4.8
OBJECT IDENTIFIER    

loopbackTarget 1.1.890.1.5.13.5.4.1.1
IfIndex of the port which would be performed loopback test.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

loopbackOps 1.1.890.1.5.13.5.4.1.2
The manager sets the corresponding bit value to 1 to start the loopback test and the agent clears the object to zero when loopback test is successfully completed. The various bit positions are: BIT 1: local loopback BIT 2: remote F5 loopback.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

loopbackVpi 1.1.890.1.5.13.5.4.1.3
VPI of the virtual channel which would be performed loopback test.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

loopbackVci 1.1.890.1.5.13.5.4.1.4
VCI of the virtual channel which would be performed loopback test.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

loopbackStatus 1.1.890.1.5.13.5.4.1.5
Loopback test status message.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

ldmTarget 1.1.890.1.5.13.5.4.2.1
IfIndex of the port which would be performed ldm test.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

ldmOps 1.1.890.1.5.13.5.4.2.2
The manager sets the object to 1 to start the ldm test and the agent clears the object to zero when ldm test is successfully completed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

ldmStatus 1.1.890.1.5.13.5.4.2.3
Status description of ldm test result.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

ldmAtucLoopAttenuation 1.1.890.1.5.13.5.4.2.4
Loop Attenuation.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmAtucSignalAttenuation 1.1.890.1.5.13.5.4.2.5
Signal Attenuation.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmAtucSignalMargin 1.1.890.1.5.13.5.4.2.6
Signal Margin.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmAtucAggregateTxPower 1.1.890.1.5.13.5.4.2.7
Actual Aggregate Transmit Power.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmAtucAttainableBitRate 1.1.890.1.5.13.5.4.2.8
Attainable Bit Rate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ldmAturLoopAttenuation 1.1.890.1.5.13.5.4.2.9
Loop Attenuation.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmAturSignalAttenuation 1.1.890.1.5.13.5.4.2.10
Signal Attenuation.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmAturSignalMargin 1.1.890.1.5.13.5.4.2.11
Signal Margin.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmAturAggregateTxPower 1.1.890.1.5.13.5.4.2.12
Actual Aggregate Transmit Power.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmAturAttainableBitRate 1.1.890.1.5.13.5.4.2.13
Attainable Bit Rate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ldmAtucNumOfSubcarriersPerPort 1.1.890.1.5.13.5.4.2.14
The number of subcarriers per port for ATU-C.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmAturNumOfSubcarriersPerPort 1.1.890.1.5.13.5.4.2.15
The number of subcarriers per port for ATU-R.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmAtucHlinScale 1.1.890.1.5.13.5.4.2.16
Scale of Hlin.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmAtucHlinReal1 1.1.890.1.5.13.5.4.2.17
The object provides real part of Hlin for the first 256 subcarriers. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmAtucHlinReal2 1.1.890.1.5.13.5.4.2.18
The object provides real part of Hlin for the last 256 subcarriers. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmAtucHlinImage1 1.1.890.1.5.13.5.4.2.19
The object provides image part of Hlin for the first 256 subcarriers. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmAtucHlinImage2 1.1.890.1.5.13.5.4.2.20
The object provides image part of Hlin for the last 256 subcarriers. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmAtucHlog1 1.1.890.1.5.13.5.4.2.21
The object provides Hlog for the first 256 subcarriers. Each subcarrier takes two octets to store the value. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmAtucHlog2 1.1.890.1.5.13.5.4.2.22
The object provides Hlog for the last 256 subcarriers. Each subcarrier takes two octets to store the value. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmAtucQln1 1.1.890.1.5.13.5.4.2.23
The object provides QLN for the first 256 subcarriers. Each subcarrier takes two octets to store the value. A special value 0 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmAtucQln2 1.1.890.1.5.13.5.4.2.24
The object provides QLN for the last 256 subcarriers. Each subcarrier takes two octets to store the value. A special value 0 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmAtucSnr1 1.1.890.1.5.13.5.4.2.25
The object provides SNR for the first 256 subcarriers. Each subcarrier takes two octets to store the value. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmAtucSnr2 1.1.890.1.5.13.5.4.2.26
The object provides SNR for the last 256 subcarriers. Each subcarrier takes two octets to store the value. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmAturHlinScale 1.1.890.1.5.13.5.4.2.27
Scale of Hlin.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmAturHlinReal 1.1.890.1.5.13.5.4.2.28
Real part of Hlin. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmAturHlinImage 1.1.890.1.5.13.5.4.2.29
Image part of Hlin. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmAturHlog 1.1.890.1.5.13.5.4.2.30
Hlog of subcarrier. Each subcarrier takes two octets to store the value. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmAturQln 1.1.890.1.5.13.5.4.2.31
QLN of subcarrier. Each subcarrier takes two octets to store the value. A special value 0 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmAturSnr 1.1.890.1.5.13.5.4.2.32
SNR of subcarrier. Each subcarrier takes two octets to store the value. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

seltTarget 1.1.890.1.5.13.5.4.3.1
IfIndex of the port which would be performed single end loopback test.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

seltOps 1.1.890.1.5.13.5.4.3.2
The manager sets the object to 1 to start the selt and the agent clears the object to zero when selt is successfully completed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

seltStatus 1.1.890.1.5.13.5.4.3.3
Status description of the selt result.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

seltCableType 1.1.890.1.5.13.5.4.3.4
The cable type that selt result indicates.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER awg24(1), awg26(2)  

seltLoopEstimateLengthFt 1.1.890.1.5.13.5.4.3.5
The estimated loop length that selt result indicates.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

seltLoopEstimateLengthMeter 1.1.890.1.5.13.5.4.3.6
The estimated loop length that selt result indicates.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltTarget 1.1.890.1.5.13.5.4.4.1
IfIndex of the port which would be performed Metallic Link Test.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mltOps 1.1.890.1.5.13.5.4.4.2
The manager sets the object to 1 to start the mlt and the agent clears the object to zero when mlt is successfully completed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mltOption 1.1.890.1.5.13.5.4.4.3
all : test all items vac: test AC voltage vdc: test DC voltage rload: test load resistance riso: test isolation resistance cap: test capacitor ren: test REN value ring: test ring voltage metering: test metering voltage dialtone: test dialtone digit: test digit roh: test roh
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER all(1), vac(2), vdc(3), rload(4), riso(5), cap(6), ren(7), ring(8), metering(9), dialtone(10), digit(11), roh(12)  

mltForce 1.1.890.1.5.13.5.4.4.4
Force test even the port is in use.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER force(1), not-force(2)  

mltResult 1.1.890.1.5.13.5.4.4.5
OBJECT IDENTIFIER    

mltVacTip 1.1.890.1.5.13.5.4.4.5.1
[Special value]: 250000016 : No result. 250000032 : Test failed. 250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set. 250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook. 250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook. 250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service. 250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook. 250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc). 250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltVacRing 1.1.890.1.5.13.5.4.4.5.2
[Special value]: 250000016 : No result. 250000032 : Test failed. 250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set. 250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook. 250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook. 250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service. 250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook. 250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc). 250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltVacDiff 1.1.890.1.5.13.5.4.4.5.3
[Special value]: 250000016 : No result. 250000032 : Test failed. 250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set. 250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook. 250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook. 250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service. 250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook. 250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc). 250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltVdcTip 1.1.890.1.5.13.5.4.4.5.4
[Special value]: 250000016 : No result. 250000032 : Test failed. 250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set. 250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook. 250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook. 250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service. 250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook. 250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc). 250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltVdcRing 1.1.890.1.5.13.5.4.4.5.5
[Special value]: 250000016 : No result. 250000032 : Test failed. 250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set. 250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook. 250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook. 250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service. 250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook. 250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc). 250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltVdcDiff 1.1.890.1.5.13.5.4.4.5.6
[Special value]: 250000016 : No result. 250000032 : Test failed. 250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set. 250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook. 250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook. 250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service. 250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook. 250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc). 250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltRLoop 1.1.890.1.5.13.5.4.4.5.7
[Special value]: 250000016 : No result. 250000032 : Test failed. 250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set. 250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook. 250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook. 250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service. 250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook. 250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc). 250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltRtg 1.1.890.1.5.13.5.4.4.5.8
[Special value]: 250000016 : No result. 250000032 : Test failed. 250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set. 250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook. 250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook. 250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service. 250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook. 250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc). 250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item. 2147483647 : Circuit open. 0 : Circuit short or fault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltRrg 1.1.890.1.5.13.5.4.4.5.9
[Special value]: 250000016 : No result. 250000032 : Test failed. 250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set. 250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook. 250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook. 250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service. 250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook. 250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc). 250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item. 2147483647 : Circuit open. 0 : Circuit short or fault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltRtr 1.1.890.1.5.13.5.4.4.5.10
[Special value]: 250000016 : No result. 250000032 : Test failed. 250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set. 250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook. 250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook. 250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service. 250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook. 250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc). 250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item. 2147483647 : Circuit open. 0 : Circuit short or fault.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltCtg 1.1.890.1.5.13.5.4.4.5.11
[Special value]: 250000016 : No result. 250000032 : Test failed. 250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set. 250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook. 250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook. 250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service. 250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook. 250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc). 250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltCrg 1.1.890.1.5.13.5.4.4.5.12
[Special value]: 250000016 : No result. 250000032 : Test failed. 250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set. 250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook. 250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook. 250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service. 250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook. 250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc). 250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltCtr 1.1.890.1.5.13.5.4.4.5.13
[Special value]: 250000016 : No result. 250000032 : Test failed. 250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set. 250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook. 250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook. 250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service. 250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook. 250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc). 250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltRen 1.1.890.1.5.13.5.4.4.5.14
[Special value]: 250000016 : No result. 250000032 : Test failed. 250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set. 250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook. 250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook. 250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service. 250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook. 250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc). 250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item. 2147483647 : Circuit open.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltVRing 1.1.890.1.5.13.5.4.4.5.15
[Special value]: 250000016 : No result. 250000032 : Test failed. 250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set. 250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook. 250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook. 250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service. 250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook. 250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc). 250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltVMetering 1.1.890.1.5.13.5.4.4.5.16
[Special value]: 250000016 : No result. 250000032 : Test failed. 250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set. 250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook. 250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook. 250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service. 250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook. 250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc). 250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltDialToneDetected 1.1.890.1.5.13.5.4.4.5.17
Value List: 1 : Yes. 2 : No. 3 : Test failed 4 : No result.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2), test-failed(3), no-result(4)  

mltDetectedDtmfCount 1.1.890.1.5.13.5.4.4.5.18
[Special value]: 250000016 : No result. 250000032 : Test failed. 250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set. 250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook. 250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook. 250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service. 250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook. 250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc). 250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltDialToneDelay 1.1.890.1.5.13.5.4.4.5.19
[Special value]: 250000016 : No result. 250000032 : Test failed. 250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set. 250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook. 250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook. 250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service. 250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook. 250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc). 250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mltReceiverState 1.1.890.1.5.13.5.4.4.5.20
[Normal Value]: 1 : On hook. 2 : Off hook. 3 : circuit short or fault. 4 : circuit open. [Special value]: 250000016 : No result. 250000032 : Test failed. 250000048 : 'Not Measured' reason # 1: Can't start the test when port is enabled and force not set. 250000064 : 'Not Measured' reason # 2: Can't start the test when port is off-hook. 250000080 : 'Not Measured' reason # 3: Can't start the test when port is disabled or on-hook. 250000096 : 'Not Measured' reason # 4: can't start the test when port is disabled or off-hook or service state is out-of-service. 250000112 : 'Not Measured' reason # 5: can't start the test when port is disabled or off-hook. 250000128 : 'Not Measured' reason # 6: The test item will be skipped when testing all items and (vTip > 0.5Vac or vRing > 0.5Vac or abs(vTip) > 0.5Vdc or abs(vRing) > 0.5Vdc). 250000144 : 'Not Measured' reason # 7: Hardware driver do not measure this item.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER on-hook(1), off-hook(2), short(3), open(4), not-measured(5)  

mltDetectedDtmfDigit 1.1.890.1.5.13.5.4.4.5.21
The DTMF digit string be detected in MLT test.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..63)  

mltErrorMsg 1.1.890.1.5.13.5.4.4.5.22
The error message when fail to start MLT test.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..128)  

mltRelayTable 1.1.890.1.5.13.5.4.4.6
Perform specified MLT relay function, or turn off MLT relay function in specified subscriber.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MltRelayEntry

mltRelayEntry 1.1.890.1.5.13.5.4.4.6.1
An entry of mltRelayTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MltRelayEntry  

mltRelaySet 1.1.890.1.5.13.5.4.4.6.1.1
By default, relay function is turned off.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER in(1), out(2), both(3), off(4)  

mltRelayTimeout 1.1.890.1.5.13.5.4.4.6.1.2
Relays will be turned off automatically while the specified timer is timeout. This object is supported by R5.01 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

mltRelayForce 1.1.890.1.5.13.5.4.4.6.1.3
Set to 1 to force to set relays even the port is in use. This object is supported by R5.01 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mltType 1.1.890.1.5.13.5.4.4.7
option(All) : all(0), test vac, vdc, riso, cap(1) option(Ring) : normal(0), start to ring(1), stop to ring(2) option(Digit) : normal(0), user input dtmf(1)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mltCount 1.1.890.1.5.13.5.4.4.8
When test mltOption digit(11) and mltType set to user input dtmf(1), set the number of digit for testing.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mltAbort 1.1.890.1.5.13.5.4.4.9
Set the slot id of a VoIP Card to terminate MLT test on it.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

oamloopbackTarget 1.1.890.1.5.13.5.4.5.1
IfIndex of the port which would be performed oamloopback test.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

oamloopbackOps 1.1.890.1.5.13.5.4.5.2
The manager sets the corresponding bit value to 1 to start the oamloopback test and the agent clears the object to zero when oamloopback test is completed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

oamloopbackPacketNumber 1.1.890.1.5.13.5.4.5.3
Number of packets to be sent. 1~100000
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

oamloopbackPacketSize 1.1.890.1.5.13.5.4.5.4
Size of each packet. 64~1518
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

oamloopbackResult 1.1.890.1.5.13.5.4.5.5
OBJECT IDENTIFIER    

oamloopbackRecvCnt 1.1.890.1.5.13.5.4.5.5.1
Number of packets received.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

oamloopbackElapseTime 1.1.890.1.5.13.5.4.5.5.2
oamloopback test elapsed time.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

oamloopbackErrorStatus 1.1.890.1.5.13.5.4.5.5.3
oamloopback test status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER ok(0), alloc-fail(1), loopback-command-timeout(2), receive-packet-timeout(3), receive-packet-error(4), remote-state-error(5), unknown-result(6)  

vdslldmTarget 1.1.890.1.5.13.5.4.6.1
IfIndex of the port which would be performed vdsl ldm test.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

vdslldmOps 1.1.890.1.5.13.5.4.6.2
The manager sets the object to 1 to start the vdsl ldm test and the agent clears the object to zero when ldm test is successfully completed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

vdslldmStatus 1.1.890.1.5.13.5.4.6.3
Status description of vdsl ldm test result.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

ldmVtuNeLoopAttenuationUS0 1.1.890.1.5.13.5.4.6.4
Loop Attenuation at US0 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuNeLoopAttenuationUS1 1.1.890.1.5.13.5.4.6.5
Loop Attenuation at US1 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuNeLoopAttenuationUS2 1.1.890.1.5.13.5.4.6.6
Loop Attenuation at US2 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuNeLoopAttenuationUS3 1.1.890.1.5.13.5.4.6.7
Loop Attenuation at US3 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuNeSignalAttenuationUS0 1.1.890.1.5.13.5.4.6.8
Signal Attenuation at US0 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuNeSignalAttenuationUS1 1.1.890.1.5.13.5.4.6.9
Signal Attenuation at US1 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuNeSignalAttenuationUS2 1.1.890.1.5.13.5.4.6.10
Signal Attenuation at US2 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuNeSignalAttenuationUS3 1.1.890.1.5.13.5.4.6.11
Signal Attenuation at US3 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuNeSignalMarginUS0 1.1.890.1.5.13.5.4.6.12
Signal Margin at US0 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuNeSignalMarginUS1 1.1.890.1.5.13.5.4.6.13
Signal Margin at US1 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuNeSignalMarginUS2 1.1.890.1.5.13.5.4.6.14
Signal Margin at US2 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuNeSignalMarginUS3 1.1.890.1.5.13.5.4.6.15
Signal Margin at US3 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuNeAggregateTxPower 1.1.890.1.5.13.5.4.6.16
Actual Aggregate Transmit Power. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuNeAttainableBitRate 1.1.890.1.5.13.5.4.6.17
Attainable Bit Rate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ldmVtuFeLoopAttenuationDS1 1.1.890.1.5.13.5.4.6.18
Loop Attenuation at DS1 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuFeLoopAttenuationDS2 1.1.890.1.5.13.5.4.6.19
Loop Attenuation at DS2 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuFeLoopAttenuationDS3 1.1.890.1.5.13.5.4.6.20
Loop Attenuation at DS3 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuFeSignalAttenuationDS1 1.1.890.1.5.13.5.4.6.21
Signal Attenuation at DS1 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuFeSignalAttenuationDS2 1.1.890.1.5.13.5.4.6.22
Signal Attenuation at DS2 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuFeSignalAttenuationDS3 1.1.890.1.5.13.5.4.6.23
Signal Attenuation at DS3 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuFeSignalMarginDS1 1.1.890.1.5.13.5.4.6.24
Signal Margin at DS1 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuFeSignalMarginDS2 1.1.890.1.5.13.5.4.6.25
Signal Margin at DS2 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuFeSignalMarginDS3 1.1.890.1.5.13.5.4.6.26
Signal Margin at DS3 band. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuFeAggregateTxPower 1.1.890.1.5.13.5.4.6.27
Actual Aggregate Transmit Power. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuFeAttainableBitRate 1.1.890.1.5.13.5.4.6.28
Attainable Bit Rate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ldmVtuNeHlinScale 1.1.890.1.5.13.5.4.6.29
Scale of Hlin.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuNeHlinReal 1.1.890.1.5.13.5.4.6.30
The object provides real part of Hlin for the subcarriers. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmVtuNeHlinImage 1.1.890.1.5.13.5.4.6.31
The object provides image part of Hlin for the subcarriers. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmVtuNeHlog 1.1.890.1.5.13.5.4.6.32
The object provides Hlog for the subcarriers. Each subcarrier takes two octets to store the value. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmVtuNeQln 1.1.890.1.5.13.5.4.6.33
The object provides QLN for the subcarriers. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmVtuNeSnr 1.1.890.1.5.13.5.4.6.34
The object provides SNR for the subcarriers. Each subcarrier takes two octets to store the value. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmVtuFeHlinScale 1.1.890.1.5.13.5.4.6.35
Scale of Hlin.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuFeHlinReal 1.1.890.1.5.13.5.4.6.36
Real part of Hlin. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmVtuFeHlinImage 1.1.890.1.5.13.5.4.6.37
Image part of Hlin. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmVtuFeHlog 1.1.890.1.5.13.5.4.6.38
Hlog of subcarrier. Each subcarrier takes two octets to store the value. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmVtuFeQln 1.1.890.1.5.13.5.4.6.39
QLN of subcarrier. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmVtuFeSnr 1.1.890.1.5.13.5.4.6.40
SNR of subcarrier. Each subcarrier takes two octets to store the value. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

ldmVtuNeHlinGroupSize 1.1.890.1.5.13.5.4.6.41
Number of sub-carriers per group used to report the H(f) linear representation values for the respective transmission direction. The valid values are 1, 2, 4 and 8. This object is supported by R5.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuFeHlinGroupSize 1.1.890.1.5.13.5.4.6.42
Number of sub-carriers per group used to report the H(f) linear representation values for the respective transmission direction. The valid values are 1, 2, 4 and 8. This object is supported by R5.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuNeHlogGroupSize 1.1.890.1.5.13.5.4.6.43
Number of sub-carriers per group used to report the H(f) linear representation values for the respective transmission direction. The valid values are 1, 2, 4 and 8. This object is supported by R5.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuFeHlogGroupSize 1.1.890.1.5.13.5.4.6.44
Number of sub-carriers per group used to report the H(f) linear representation values for the respective transmission direction. The valid values are 1, 2, 4 and 8. This object is supported by R5.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuNeQlnGroupSize 1.1.890.1.5.13.5.4.6.45
Number of sub-carriers per group used to report the Quiet Line Noise values for the respective transmission direction. The valid values are 1, 2, 4 and 8. This object is supported by R5.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuFeQlnGroupSize 1.1.890.1.5.13.5.4.6.46
Number of sub-carriers per group used to report the Quiet Line Noise values for the respective transmission direction. The valid values are 1, 2, 4 and 8. This object is supported by R5.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuNeSnrGroupSize 1.1.890.1.5.13.5.4.6.47
Number of sub-carriers per group used to report the SNR values on the respective transmission direction. The valid values are 1, 2, 4 and 8. This object is supported by R5.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ldmVtuFeSnrGroupSize 1.1.890.1.5.13.5.4.6.48
Number of sub-carriers per group used to report the SNR values on the respective transmission direction. The valid values are 1, 2, 4 and 8. This object is supported by R5.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaOamF5LoopbackTargetGroupIndex 1.1.890.1.5.13.5.4.7.1
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

imaOamF5LoopbackTargetVpi 1.1.890.1.5.13.5.4.7.2
VPI of the virtual channel which would be performed imaOamF5Loopback test.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

imaOamF5LoopbackTargetVci 1.1.890.1.5.13.5.4.7.3
VCI of the virtual channel which would be performed imaOamF5Loopback test.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

imaOamF5LoopbackType 1.1.890.1.5.13.5.4.7.4
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER end-to-end(1), segment(2)  

imaOamF5LoopbackOps 1.1.890.1.5.13.5.4.7.5
The manager sets the corresponding bit value to 1 to start the imaOamF5Loopback test and the agent clears the object to zero when loopback test is successfully completed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

imaOamF5LoopbackSegmentId 1.1.890.1.5.13.5.4.7.6
16 bytes segment id.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

imaOamF5LoopbackStatus 1.1.890.1.5.13.5.4.7.7
Status description of IMA OAM F5 Loopback test result.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

xdsl2ExtSCStatusTable 1.1.890.1.5.13.5.4.8.1
The table xdsl2ExtSCStatusTable extends xdsl2SCStatusTable for ZyXEL product.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xdsl2ExtSCStatusEntry

xdsl2ExtSCStatusEntry 1.1.890.1.5.13.5.4.8.1.1
The table xdsl2ExtSCStatusTable contains extra subcarrier status parameters besides those in xdsl2LineSegmentTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Xdsl2ExtSCStatusEntry  

xdsl2SCStatusActAtp 1.1.890.1.5.13.5.4.8.1.1.1
Actual Aggregate Transmit Power Downstream. The total amount of transmit power delivered by the xTU-C at the U-C reference point, at the instant of measurement. It ranges from -310 to 310 units of 0.1 dBm (Physical values are -31 to 31 dBm). A value of 0x7FFFFFFF (2147483647) indicates the measurement is out of range to be represented. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -310..310 | 2147483647  

xdsl2ExtSCStatusBandTable 1.1.890.1.5.13.5.4.8.2
The table xdsl2ExtSCStatusBandTable extends xdsl2SCStatusBandTable for ZyXEL product.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xdsl2ExtSCStatusBandEntry

xdsl2ExtSCStatusBandEntry 1.1.890.1.5.13.5.4.8.2.1
The table xdsl2ExtSCStatusBandTable contains extra subcarrier status parameters that are grouped per-band besides those in xdsl2SCStatusBandTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Xdsl2ExtSCStatusBandEntry  

xdsl2SCStatusBandSnrMargin 1.1.890.1.5.13.5.4.8.2.1.1
SNR Margin is the maximum increase in dB of the noise power received at the xTU (xTU-R for a band in the downstream direction and xTU-C for a band in the upstream direction), such that the BER requirements are met for all bearer channels received at the xTU. Values range from -640 to 630 in units of 0.1 dB (Physical values are -64 to 63 dB). A special value of 0x7FFFFFFF (2147483647) indicates the SNR Margin is out of range to be represented. A special value of 0x7FFFFFFE (2147483646) indicates the SNR Margin measurement is currently unavailable. This object reflects the value of the parameter following the most recent DELT performed on the associated line. Once the DELT process is over, the parameter no longer changes until the row is deleted or a new DELT process is initiated.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -640..630 | 2147483646 | 2147483647  

staticRoute 1.1.890.1.5.13.5.5.1
OBJECT IDENTIFIER    

maxNumOfStaticRoutes 1.1.890.1.5.13.5.5.1.1
The maximum number of static routes supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

staticRouteTable 1.1.890.1.5.13.5.5.1.2
A table that contains information about static routes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    StaticRouteEntry

staticRouteEntry 1.1.890.1.5.13.5.5.1.2.1
A list of static route entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  StaticRouteEntry  

staticRouteName 1.1.890.1.5.13.5.5.1.2.1.1
The name of the static route.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

staticRouteDest 1.1.890.1.5.13.5.5.1.2.1.2
The destination IP address of the static route.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

staticRouteMask 1.1.890.1.5.13.5.5.1.2.1.3
The subnet mask of the static route.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

staticRouteGateway 1.1.890.1.5.13.5.5.1.2.1.4
The gateway IP address of the static route.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

staticRouteMetric 1.1.890.1.5.13.5.5.1.2.1.5
The routing metric of the static route.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

staticRouteRowStatus 1.1.890.1.5.13.5.5.1.2.1.6
This object is used to create a new row or modify or delete an existing row in this table. A row is activated by setting this object to `active', , and is deactivated by setting it to 'notInService'.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

staticIp 1.1.890.1.5.13.5.5.2
OBJECT IDENTIFIER    

staticIpInbandIp 1.1.890.1.5.13.5.5.2.1
Inband IP Address. Not immediately apply. Use staticIpOps to apply the object setting on device.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

staticIpInbandMask 1.1.890.1.5.13.5.5.2.2
Inband IP Mask. Not immediately apply. Use staticIpOps to apply the object setting on device.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

staticIpInbandVlan 1.1.890.1.5.13.5.5.2.3
Inband IP Vlan. Not immediately apply. Use staticIpOps to apply the object setting on device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

staticIpOutbandIp 1.1.890.1.5.13.5.5.2.4
Outband IP Address. Not immediately apply. Use staticIpOps to apply the object setting on device.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

staticIpOutbandMask 1.1.890.1.5.13.5.5.2.5
Outband IP Mask. Not immediately apply. Use staticIpOps to apply the object setting on device.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

staticIpGatewayIP 1.1.890.1.5.13.5.5.2.6
Gateway IP Address. Not immediately apply. Use staticIpOps to apply the object setting on device.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

staticIpOps 1.1.890.1.5.13.5.5.2.7
The manager setting will temporary saved but not set into Device. Set value of staticIpOps to 1 to apply the setting of IpTable on device. Set value of staticIpOps to 2 to reload the real setting of IpTable on device now.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER set(1), reload(2)  

numOfChassis 1.1.890.1.5.13.5.6.1
The number of chassis in the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

chassisTable 1.1.890.1.5.13.5.6.2
The table which contains the chassis information in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ChassisEntry

chassisEntry 1.1.890.1.5.13.5.6.2.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  ChassisEntry  

chassisId 1.1.890.1.5.13.5.6.2.1.1
The Chassis ID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

chassisFrameNumber 1.1.890.1.5.13.5.6.2.1.2
The Frame ID.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

chassisSerialNumber 1.1.890.1.5.13.5.6.2.1.3
The Chassis Serial Number.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

chassisNumber 1.1.890.1.5.13.5.6.2.1.4
The Chassis Number which is defined by the system administrator for management purpose.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..64  

chassisStatus 1.1.890.1.5.13.5.6.2.1.5
The current status of the chassis.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER empty(1), up(2), down(3), testing(4)  

slotTable 1.1.890.1.5.13.5.6.3
The table which contains the slot information in a chassis.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlotEntry

slotEntry 1.1.890.1.5.13.5.6.3.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SlotEntry  

slotId 1.1.890.1.5.13.5.6.3.1.1
Identity of the slot.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

slotModuleType 1.1.890.1.5.13.5.6.3.1.2
Card type of the plug-in card.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), msc1000G(101), alc1248G-51(102), alc1248G-53(103), slc1248G-22(104), vlc1224G-41(105), msc1024G(106), alc1272G-51(107), vop1248G-61-SIP(108), msc1000GA(109), vlc1324G-51(110), msc1224G(111), vop1248G-61-H248(112), vlc1348G-51(113), elc1220G-55(114), msc1024GA(115), vlc1324G-53(116), ima1408G-81(117), vlc1424G-56(118), slc1348G-22(119), vlc1348G-53(120), alc1372G-51(121), msc1024GB(122), msc1224GB(123), vop1372G-61-H248(124), msc1024GC(125), glc1320G-55(126), vop1372G-61-SIP(127), alc1348G-51C(128), alc1348G-51C-H248(129)  

slotModuleDescr 1.1.890.1.5.13.5.6.3.1.3
The descriptions of the plug-in card.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

slotModuleFWVersion 1.1.890.1.5.13.5.6.3.1.4
The firmware version of the plug-in card.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

slotModuleDriverVersion 1.1.890.1.5.13.5.6.3.1.5
The DSL driver of the plug-in card.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

slotModuleModemCodeVersion 1.1.890.1.5.13.5.6.3.1.6
The DSL modem code version of the plug-in card.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

slotModuleStatus 1.1.890.1.5.13.5.6.3.1.7
The module state of the plug-in card.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER empty(1), up(2), down(3), testing(4), standby(5)  

slotModuleAlarmStatus 1.1.890.1.5.13.5.6.3.1.8
This variable indicates the alarm status of the module. It is a bit map represented a sum, therefore, it can represent multiple defects simultaneously. The moduleNoDefect should be set if and only if no other flag is set. The various bit positions are: 1 moduleNoDefect 2 moduleOverHeat 3 moduleFanRpmLow 4 moduleVoltageLow 5 moduleThermalSensorFailure 6 modulePullOut 7 powerDC48VAFailure 8 powerDC48VBFailure 9 extAlarmInputTrigger 10 moduleDown 11 mscSwitchOverOK 12 networkTopologyChange 13 macSpoof 14 cpuHigh 15 memoryUsageHigh 16 packetBufferUsageHigh 17 loopguardOccurence
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

slotModuleSerialNumber 1.1.890.1.5.13.5.6.3.1.9
The serial number of the plug-in card.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

slotModuleHWVersion 1.1.890.1.5.13.5.6.3.1.10
The hardware version of the plug-in card.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

slotModuleUpTime 1.1.890.1.5.13.5.6.3.1.11
The time (in seconds) since the plug-in card was last re-initialized.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

slotModuleMacAddress 1.1.890.1.5.13.5.6.3.1.12
The MAC Address of the plug-in card.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

slotModuleMacAddress2 1.1.890.1.5.13.5.6.3.1.13
The MAC Address of the plug-in card.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

mscPortTable 1.1.890.1.5.13.5.6.4
The table contains MSC port status.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MscPortEntry

mscPortEntry 1.1.890.1.5.13.5.6.4.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  MscPortEntry  

mscPortId 1.1.890.1.5.13.5.6.4.1.1
Identity of the MSC port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mscPortType 1.1.890.1.5.13.5.6.4.1.2
Type of the MSC port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), e1000BaseT(2), e1000BaseLX(3), e1000BaseSX(4), e100BaseFX(5), e100BaseTX(6), e1000BaseGBIC(7), e10000BaseGBIC(8)  

staticMulticast 1.1.890.1.5.13.5.7.2
OBJECT IDENTIFIER    

igmpFilter 1.1.890.1.5.13.5.7.3
OBJECT IDENTIFIER    

mcastBandwidth 1.1.890.1.5.13.5.7.4
OBJECT IDENTIFIER    

igmpCount 1.1.890.1.5.13.5.7.5
OBJECT IDENTIFIER    

mvlan 1.1.890.1.5.13.5.7.6
OBJECT IDENTIFIER    

queryVid 1.1.890.1.5.13.5.7.7
OBJECT IDENTIFIER    

igmpEnable 1.1.890.1.5.13.5.7.1
Enable/disable IGMP protocol.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enableProxy(1), enableSnooping(2), disable(3)  

igmpMode 1.1.890.1.5.13.5.7.8
Setting IGMP with aggresive mode will issue an IGMP report from new active port when topology change occurs, while normal mode won't.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER aggresive(1), normal(2)  

igmpVersion 1.1.890.1.5.13.5.7.9
Setting IGMP version. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER v2(1), v3(2), mldv1(3), mldv2(4)  

igmpFastLeaveEnable 1.1.890.1.5.13.5.7.10
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

igmpFastLeaveTimer 1.1.890.1.5.13.5.7.11
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

unknownMulticast 1.1.890.1.5.13.5.7.12
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER drop(1), flood(2)  

ipv6PassThrough 1.1.890.1.5.13.5.7.13
Set IPv6 packet transparent passthrough.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER drop(1), flood(2), disable(3)  

reservedGroup 1.1.890.1.5.13.5.7.14
Set reserved packets transparent passthrougth
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER drop(1), flood(2)  

igmpHistoryTable 1.1.890.1.5.13.5.7.15
This table contains multicast IGMP/MLD history configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpHistoryEntry

igmpHistoryEntry 1.1.890.1.5.13.5.7.15.1
The entry of multicast igmp history table.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpHistoryEntry  

igmphistoryenable 1.1.890.1.5.13.5.7.15.1.1
Enable/disable IGMP/MLD multicast group join/leave history logging.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

maxNumberOfMcastGroups 1.1.890.1.5.13.5.7.2.1
The max number of static multicast groups supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mcastGroupTable 1.1.890.1.5.13.5.7.2.2
A table that contains static multicast group information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McastGroupEntry

mcastGroupEntry 1.1.890.1.5.13.5.7.2.2.1
The entry of multicast group table.
Status: current Access: not-accessible
OBJECT-TYPE    
  McastGroupEntry  

mcastGroupIp 1.1.890.1.5.13.5.7.2.2.1.1
The multicast IP address of the group.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

mcastGroupFixedPorts 1.1.890.1.5.13.5.7.2.2.1.2
The port list which specify the ports joining the multicast group.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

mcastGroupForbiddenPorts 1.1.890.1.5.13.5.7.2.2.1.3
The port list which specify the ports prohibited by the multicast group.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

mcastGroupRowStatus 1.1.890.1.5.13.5.7.2.2.1.4
The row status of the multicast group entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

maxNumberOfMacMcastGroups 1.1.890.1.5.13.5.7.2.3
The maximum number of row entries that user can create in macMcastGroupTable. This object is supported by R5.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macMcastGroupTable 1.1.890.1.5.13.5.7.2.4
This table specify the static multicast group with MAC address. This table is supported by R5.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacMcastGroupEntry

macMcastGroupEntry 1.1.890.1.5.13.5.7.2.4.1
An entry of macMcastGroupTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacMcastGroupEntry  

macMcastGroupMac 1.1.890.1.5.13.5.7.2.4.1.1
The multicast MAC address of the group.
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

macMcastGroupFixedPorts 1.1.890.1.5.13.5.7.2.4.1.2
The port list which specify the ports joining the multicast group.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

macMcastGroupRowStatus 1.1.890.1.5.13.5.7.2.4.1.3
The row status of the MAC multicast group entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

mcastInetGroupTable 1.1.890.1.5.13.5.7.2.5
A table that contains static multicast group information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McastInetGroupEntry

mcastInetGroupEntry 1.1.890.1.5.13.5.7.2.5.1
The entry of multicast group table.
Status: current Access: not-accessible
OBJECT-TYPE    
  McastInetGroupEntry  

mcastGroupInetAddrType 1.1.890.1.5.13.5.7.2.5.1.1
The multicast IP address type of the group.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

mcastGroupInetAddr 1.1.890.1.5.13.5.7.2.5.1.2
The multicast IP address of the group.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

mcastGroupInetFixedPorts 1.1.890.1.5.13.5.7.2.5.1.3
The port list which specify the ports joining the multicast group.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

mcastGroupInetForbiddenPorts 1.1.890.1.5.13.5.7.2.5.1.4
The port list which specify the ports prohibited by the multicast group.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

mcastGroupInetRowStatus 1.1.890.1.5.13.5.7.2.5.1.5
The row status of the multicast group entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

maxNumOfIgmpFilters 1.1.890.1.5.13.5.7.3.1
The max number of IGMP filters supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

igmpFilterTable 1.1.890.1.5.13.5.7.3.2
A table that contains IGMP filters.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpFilterEntry

igmpFilterEntry 1.1.890.1.5.13.5.7.3.2.1
The entry of IGMP filter table.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpFilterEntry  

igmpFilterName 1.1.890.1.5.13.5.7.3.2.1.1
The IGMP filter name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

igmpFilterIndex 1.1.890.1.5.13.5.7.3.2.1.2
The index which specif the filter rule.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

igmpFilterStartIp 1.1.890.1.5.13.5.7.3.2.1.3
The start IP of the filter rule.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

igmpFilterEndIp 1.1.890.1.5.13.5.7.3.2.1.4
The end IP of the filter rule.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

igmpFilterRowStatus 1.1.890.1.5.13.5.7.3.2.1.5
The row status of the IGMP filter entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

igmpFilterInetAddrType 1.1.890.1.5.13.5.7.3.2.1.6
The IP Address type.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

igmpFilterInetAddrStart 1.1.890.1.5.13.5.7.3.2.1.7
The start IP of the filter rule.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

igmpFilterInetAddrEnd 1.1.890.1.5.13.5.7.3.2.1.8
The end IP of the filter rule.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

igmpFilterPortTable 1.1.890.1.5.13.5.7.3.3
This table specif the IGMP filter of the port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpFilterPortEntry

igmpFilterPortEntry 1.1.890.1.5.13.5.7.3.3.1
An entry in igmpFilterPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpFilterPortEntry  

igmpFilterPortFilterName 1.1.890.1.5.13.5.7.3.3.1.1
The IGMP filter name of the port.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

igmpfilterBatchSet 1.1.890.1.5.13.5.7.3.4
OBJECT IDENTIFIER    

igmpfilterTarget 1.1.890.1.5.13.5.7.3.4.1
This managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 Byte 2~4: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8, and the second octet specifying slots 9 through 16, and so on. Byte 5~: each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

igmpfilterOps 1.1.890.1.5.13.5.7.3.4.2
The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: set IGMP filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

igmpfilterForBatchSet 1.1.890.1.5.13.5.7.3.4.3
The IGMP filter name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

mcastDefaultBandwidth 1.1.890.1.5.13.5.7.4.1
Default bandwidth requirement for a multicast channel. This object is supported by R1.02 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..100000  

maxNumOfMcastBw 1.1.890.1.5.13.5.7.4.2
The maximum number of row entries that user can create in mcastBwTable. This object is supported by R1.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mcastBwTable 1.1.890.1.5.13.5.7.4.3
This table defines bandwidth budget for a range of multicast IP channels. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McastBwEntry

mcastBwEntry 1.1.890.1.5.13.5.7.4.3.1
An entry of mcastBwTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  McastBwEntry  

mcastBwIndex 1.1.890.1.5.13.5.7.4.3.1.1
The index which specify the entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mcastBwStartIp 1.1.890.1.5.13.5.7.4.3.1.2
The start multicast IP of the bandwidth control range.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

mcastBwEndIp 1.1.890.1.5.13.5.7.4.3.1.3
The end multicast IP of the bandwidth control range.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

mcastBwBandwidth 1.1.890.1.5.13.5.7.4.3.1.4
The bandwidth budget for the multicast IP channels.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

mcastBwRowStatus 1.1.890.1.5.13.5.7.4.3.1.5
The row status of the entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

mcastBwPortTable 1.1.890.1.5.13.5.7.4.4
This table specify the multicast bandwidth control of the port. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McastBwPortEntry

mcastBwPortEntry 1.1.890.1.5.13.5.7.4.4.1
An entry of mcastBwPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  McastBwPortEntry  

mcastBwPortEnable 1.1.890.1.5.13.5.7.4.4.1.1
Enable/disable multicast bandwidth control for a port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

mcastBwPortBandwidth 1.1.890.1.5.13.5.7.4.4.1.2
Set bandwidth threshold for a port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mcastBwInetTable 1.1.890.1.5.13.5.7.4.5
This table defines bandwidth budget for a range of multicast IP channels for IPv6. This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    McastBwInetEntry

mcastBwInetEntry 1.1.890.1.5.13.5.7.4.5.1
An entry of mcastBwInetTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  McastBwInetEntry  

mcastBwInetIndex 1.1.890.1.5.13.5.7.4.5.1.1
The index which specify the entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mcastBwInetAddrType 1.1.890.1.5.13.5.7.4.5.1.2
The ip address type of multicast IP.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

mcastBwInetAddrStart 1.1.890.1.5.13.5.7.4.5.1.3
The start multicast IP of the bandwidth control range.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

mcastBwInetAddrEnd 1.1.890.1.5.13.5.7.4.5.1.4
The end multicast IP of the bandwidth control range.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

mcastBwInetBandwidth 1.1.890.1.5.13.5.7.4.5.1.5
The bandwidth budget for the multicast IP channels.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

mcastBwInetRowStatus 1.1.890.1.5.13.5.7.4.5.1.6
The row status of the entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

igmpCountPortTable 1.1.890.1.5.13.5.7.5.1
This table specify the IGMP count limiting of the port. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpCountPortEntry

igmpCountPortEntry 1.1.890.1.5.13.5.7.5.1.1
An entry of igmpCountPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpCountPortEntry  

igmpCountPortEnable 1.1.890.1.5.13.5.7.5.1.1.1
Enable/disable IGMP count limiting for a port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

igmpCountPortLimit 1.1.890.1.5.13.5.7.5.1.1.2
The maximum allowed IGMP report count for a port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

igmpMessageCountPortTable 1.1.890.1.5.13.5.7.5.2
This table specify the IGMP message count limiting of the port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpMessageCountPortEntry

igmpMessageCountPortEntry 1.1.890.1.5.13.5.7.5.2.1
An entry of igmpMessageCountPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpMessageCountPortEntry  

igmpMessageCountPortEnable 1.1.890.1.5.13.5.7.5.2.1.1
Enable/disable IGMP message count limiting for a port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

igmpMessageCountPortLimit 1.1.890.1.5.13.5.7.5.2.1.2
The maximum allowed IGMP message count for a port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

maxNumOfMvlan 1.1.890.1.5.13.5.7.6.1
The maximum number of row entries that user can create in mvlanTable.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mvlanTable 1.1.890.1.5.13.5.7.6.2
A table containing static configuration information for each multicast VLAN configured into the device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MvlanEntry

mvlanEntry 1.1.890.1.5.13.5.7.6.2.1
An entry of mvlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MvlanEntry  

mvlanIndex 1.1.890.1.5.13.5.7.6.2.1.1
The VLAN-ID refering to this VLAN.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

mvlanName 1.1.890.1.5.13.5.7.6.2.1.2
An administratively assigned string, which may be used to identify the VLAN.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

mvlanEgressPorts 1.1.890.1.5.13.5.7.6.2.1.3
The set of ports which are permanently assigned to the egress list for this multicast VLAN.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

mvlanRowStatus 1.1.890.1.5.13.5.7.6.2.1.4
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

mvlan8021pPriority 1.1.890.1.5.13.5.7.6.2.1.5
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

mvlanTranslateTable 1.1.890.1.5.13.5.7.6.3
A table that contains multicast to VLAN translation.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MvlanTranslateEntry

mvlanTranslateEntry 1.1.890.1.5.13.5.7.6.3.1
An entry of mvlanTranslateTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MvlanTranslateEntry  

mvlanTranslateIndex 1.1.890.1.5.13.5.7.6.3.1.1
The index which specif the entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mvlanTranslateStartIp 1.1.890.1.5.13.5.7.6.3.1.2
The start IP of the multicast VLAN translation.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

mvlanTranslateEndIp 1.1.890.1.5.13.5.7.6.3.1.3
The end IP of the multicast VLAN translation.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

mvlanTranslateInetAddrType 1.1.890.1.5.13.5.7.6.3.1.4
The IP Address type.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

mvlanTranslateInetAddrStart 1.1.890.1.5.13.5.7.6.3.1.5
The start IP of the multicast VLAN translation.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

mvlanTranslateInetAddrEnd 1.1.890.1.5.13.5.7.6.3.1.6
The end IP of the multicast VLAN translation.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

mvlanExtTable 1.1.890.1.5.13.5.7.6.4
A table that contains MVLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MvlanExtEntry

mvlanExtEntry 1.1.890.1.5.13.5.7.6.4.1
An entry of mvlanExtTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MvlanExtEntry  

mvlanExtReg 1.1.890.1.5.13.5.7.6.4.1.1
Egress or forbid to the Multicast VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fix(1), forbid(2)  

mvlanExtCvid 1.1.890.1.5.13.5.7.6.4.1.2
Customer VLAN
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mvlanNonmemberPort 1.1.890.1.5.13.5.7.6.5
set this object to 'discard' so that the system discards IGMP/MLD reports if the subscriber port is not a member of the MVLAN which the group address belong to. Set to 'pass' so that the system accepts such IGMP/MLD reports and process them with the original VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER discard(1), pass(2)  

maxNumOfQryVid 1.1.890.1.5.13.5.7.7.1
The maximum number of row entries that user can create in qryVidConfTable. This object is supported by R1.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

qryVidConfTable 1.1.890.1.5.13.5.7.7.2
This table defines statically set VLANs used for response IGMP report. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QryVidConfEntry

qryVidConfEntry 1.1.890.1.5.13.5.7.7.2.1
An entry in qryVidConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  QryVidConfEntry  

qryVid 1.1.890.1.5.13.5.7.7.2.1.1
VLAN ID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

qryVidRowStatus 1.1.890.1.5.13.5.7.7.2.1.2
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

qryVidStatusTable 1.1.890.1.5.13.5.7.7.3
This table shows statically set or dynamically learned VLANs used for response IGMP report.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QryVidStatusEntry

qryVidStatusEntry 1.1.890.1.5.13.5.7.7.3.1
An entry in qryVidStatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  QryVidStatusEntry  

qryVidType 1.1.890.1.5.13.5.7.7.3.1.1
VLAN type.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER static(1), dynamic(2)  

adslPort 1.1.890.1.5.13.5.8.2
OBJECT IDENTIFIER    

shdslPort 1.1.890.1.5.13.5.8.3
OBJECT IDENTIFIER    

pvc 1.1.890.1.5.13.5.8.4
OBJECT IDENTIFIER    

ppvc 1.1.890.1.5.13.5.8.5
OBJECT IDENTIFIER    

portOperation 1.1.890.1.5.13.5.8.6
OBJECT IDENTIFIER    

pvcStats 1.1.890.1.5.13.5.8.7
OBJECT IDENTIFIER    

paepvc 1.1.890.1.5.13.5.8.8
OBJECT IDENTIFIER    

tlspvc 1.1.890.1.5.13.5.8.9
OBJECT IDENTIFIER    

vdslPort 1.1.890.1.5.13.5.8.10
OBJECT IDENTIFIER    

ipbpvc 1.1.890.1.5.13.5.8.11
OBJECT IDENTIFIER    

voipPort 1.1.890.1.5.13.5.8.12
OBJECT IDENTIFIER    

enetPort 1.1.890.1.5.13.5.8.13
OBJECT IDENTIFIER    

dtpvc 1.1.890.1.5.13.5.8.15
OBJECT IDENTIFIER    

e1Port 1.1.890.1.5.13.5.8.16
OBJECT IDENTIFIER    

xvlan 1.1.890.1.5.13.5.8.17
OBJECT IDENTIFIER    

vdsl2Port 1.1.890.1.5.13.5.8.18
OBJECT IDENTIFIER    

subrPortTable 1.1.890.1.5.13.5.8.1
This table includes subscriber attributes for the port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SubrPortEntry

subrPortEntry 1.1.890.1.5.13.5.8.1.1
An entry in subrPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SubrPortEntry  

subrPortName 1.1.890.1.5.13.5.8.1.1.1
Name of the subscriber.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..47)  

subrPortTel 1.1.890.1.5.13.5.8.1.1.2
Telephone number of the subscriber.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..31)  

subrPortMdf 1.1.890.1.5.13.5.8.1.1.3
MDF information of this subscriber port
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..47)  

adslLineConfTable 1.1.890.1.5.13.5.8.2.1
This table includes common attributes describing the ADSL line.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdslLineConfEntry

adslLineConfEntry 1.1.890.1.5.13.5.8.2.1.1
An entry in adslLineConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AdslLineConfEntry  

adslLineConfAdslMode 1.1.890.1.5.13.5.8.2.1.1.1
G.lite and T1.413 are only applicable to annex A board. ETSI is only applicable to annex B board.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER gDotLite(1), gDotDmt(2), t1Dot413(3), auto(4), etsi(5), adsl2(6), adsl2Plus(7)  

adslLineConfAnnexL 1.1.890.1.5.13.5.8.2.1.1.2
Enable/disable annex L for the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enableNarrowMode(1), enableWideMode(2), disable(3)  

adslLineConfAnnexM 1.1.890.1.5.13.5.8.2.1.1.3
Enable/disable annex M for the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

adslLineConfAnnexI 1.1.890.1.5.13.5.8.2.1.1.4
Enable/disable annex I for the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

adslLineConfOptionMask 1.1.890.1.5.13.5.8.2.1.1.5
The semantic for each bit is: BIT 1 : Disable Trellis BIT 2 : Disable Reed-Solomon BIT 3 : Disable upstream bitswap BIT 4 : Disable downstream bitswap BIT 5 : Disable 1-bit constellation BIT 6 : Disable transmit windowing BIT 7 : Disable s=0.5 support (ADSL1 only) BIT 8 : Disable G.lite rate limit (ADSL1 only) BIT 9 : Disable Nitro mode
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslLineConfPowerMgmt 1.1.890.1.5.13.5.8.2.1.1.6
Enable/disable power management for the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enableL2(1), enableL2andL3(2), disable(3)  

adslLineConfPowerMode 1.1.890.1.5.13.5.8.2.1.1.7
The power mode of the ADSL line.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fix(1), priorityToPower(2), priorityToRate(3)  

adslLineConfAturMaxTxPower 1.1.890.1.5.13.5.8.2.1.1.8
The maximum allowed transmit power of ATU-R.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -130..200  

adslLineConfAtucMaxTxPower 1.1.890.1.5.13.5.8.2.1.1.9
The maximum allowed transmit power of ATU-C.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -50..200  

adslLineConfMaxRxPower 1.1.890.1.5.13.5.8.2.1.1.10
The maximum aggregate received power.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -255..255  

adslLineConfAturCarrierMask 1.1.890.1.5.13.5.8.2.1.1.11
The upstream carrier mask from bin 0 to 63. Bit set to 1 indicates the bin is masked off.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

adslLineConfAtucCarrierMask0 1.1.890.1.5.13.5.8.2.1.1.12
The downstream carrier mask from bin 32 to 255. Bit set to 1 indicates the bin is masked off.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

adslLineConfAtucCarrierMask1 1.1.890.1.5.13.5.8.2.1.1.13
The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates the bin is masked off.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

adslLineConfAturInp 1.1.890.1.5.13.5.8.2.1.1.14
The upstream Impulse Noise Protection minimum setting in unit of DMT symbol.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER zero(1), zero-point-five(2), one(3), two(4), four(5), eight(6), sixteen(7)  

adslLineConfAtucInp 1.1.890.1.5.13.5.8.2.1.1.15
The downstream Impulse Noise Protection minimum setting in unit of DMT symbol.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER zero(1), zero-point-five(2), one(3), two(4), four(5), eight(6), sixteen(7)  

bitLoad 1.1.890.1.5.13.5.8.2.2
OBJECT IDENTIFIER    

bitLoadTable 1.1.890.1.5.13.5.8.2.2.1
This table provides the number of bits per carrier for each ADSL port.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BitLoadEntry

bitLoadEntry 1.1.890.1.5.13.5.8.2.2.1.1
An entry in bitLoadTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  BitLoadEntry  

bitLoadBits 1.1.890.1.5.13.5.8.2.2.1.1.1
This object provides the number of bits for all carriers in the port. The first octet specify the number of bits for carrier 1, and the second octet specify the number of bits for carrier 2, and so on. The object provides the number of bits for carrier 1 to 512.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

bitLoadAtucNumOfCarriers 1.1.890.1.5.13.5.8.2.2.1.1.2
The number of carriers for ATU-C.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

bitLoadAturNumOfCarriers 1.1.890.1.5.13.5.8.2.2.1.1.3
The number of carriers for ATU-R.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

adslPortBatchSet 1.1.890.1.5.13.5.8.2.3
OBJECT IDENTIFIER    

adslPortTarget 1.1.890.1.5.13.5.8.2.3.1
The managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 Byte 2~4: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8, and the second octet specifying slots 9 through 16, and so on. Byte 5~: each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

adslPortOps 1.1.890.1.5.13.5.8.2.3.2
The managed object is for ADSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: enable port BIT 2: disable port BIT 3: set ADSL mode BIT 4: set line profile BIT 5: set alarm profile BIT 6: enable Annex L to be narrow mode BIT 7: enable Annex L to be wide mode BIT 8: disable Annex L BIT 9: enable Annex M BIT 10: disable Annex M BIT 11: enable Annex I BIT 12: disable Annex I BIT 13: set option mask BIT 14: enable power management mode to be L2 BIT 15: enable power management mode to be L3 BIT 16: disable power management mode BIT 17: set power mode to be fixed BIT 18: set power mode to be priority to power BIT 19: set power mode to be priority to rate BIT 20: set ATU-R max Tx power BIT 21: set ATU-C max Tx power BIT 22: set max Rx power BIT 23: set ATU-R carrier mask BIT 24: set ATU-C carrier mask BIT 25: set ATU-R INP minimum setting BIT 26: set ATU-C INP minimum setting
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslModeForBatchSet 1.1.890.1.5.13.5.8.2.3.3
G.lite and T1.413 are only applicable to annex A board. ETSI is only applicable to annex B board.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER gDotLite(1), gDotDmt(2), t1Dot413(3), auto(4), etsi(5), adsl2(6), adsl2Plus(7)  

adslLineProfileForBatchSet 1.1.890.1.5.13.5.8.2.3.4
The ADSL line profile.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

adslAlarmProfileForBatchSet 1.1.890.1.5.13.5.8.2.3.5
The ADSL alarm profile.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

adslOptionMaskForBatchSet 1.1.890.1.5.13.5.8.2.3.6
The semantic for each bit is identical to the object adslLineConfOptionMask.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslAturMaxTxPowerForBatchSet 1.1.890.1.5.13.5.8.2.3.7
The maximum allowed transmit power of ATU-R.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -130..200  

adslAtucMaxTxPowerForBatchSet 1.1.890.1.5.13.5.8.2.3.8
The maximum allowed transmit power of ATU-C.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -50..200  

adslMaxRxPowerForBatchSet 1.1.890.1.5.13.5.8.2.3.9
The maximum aggregate received power.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -255..255  

adslAturCarrierMaskForBatchSet 1.1.890.1.5.13.5.8.2.3.10
The upstream carrier mask from bin 0 to 63. Bit set to 1 indicates the bin is masked off.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

adslAtucCarrierMask0ForBatchSet 1.1.890.1.5.13.5.8.2.3.11
The downstream carrier mask from bin 32 to 255. Bit set to 1 indicates the bin is masked off.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

adslAtucCarrierMask1ForBatchSet 1.1.890.1.5.13.5.8.2.3.12
The downstream carrier mask from bin 256 to 511. Bit set to 1 indicates the bin is masked off.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

adslAturInpForBatchSet 1.1.890.1.5.13.5.8.2.3.13
The upstream Impulse Noise Protection minimum setting in unit of DMT symbol.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER zero(1), zero-point-five(2), one(3), two(4), four(5), eight(6), sixteen(7)  

adslAtucInpForBatchSet 1.1.890.1.5.13.5.8.2.3.14
The downstream Impulse Noise Protection minimum setting in unit of DMT symbol.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER zero(1), zero-point-five(2), one(3), two(4), four(5), eight(6), sixteen(7)  

adslLineStatusTable 1.1.890.1.5.13.5.8.2.4
This table includes the ADSL line status.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdslLineStatusEntry

adslLineStatusEntry 1.1.890.1.5.13.5.8.2.4.1
An entry in adslLineStatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AdslLineStatusEntry  

adslLineStatusMode 1.1.890.1.5.13.5.8.2.4.1.1
The link up mode of the ADSL line. The following items is added from R5.05 8: adsl2Annexi(8) 9: adsl2Annexl(9) 10: adsl2AnnexlNarrow(10) 11: adsl2Annexm(11) 12: adsl2PlusAnnexi(12) 13: adsl2PlusAnnexm(13)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER gDotLite(1), gDotDmt(2), t1Dot413(3), etsi(4), adsl2(5), adsl2Plus(6), none(7), adsl2Annexi(8), adsl2Annexl(9), adsl2AnnexlNarrow(10), adsl2Annexm(11), adsl2PlusAnnexi(12), adsl2PlusAnnexm(13)  

adslLineStatusUpTime 1.1.890.1.5.13.5.8.2.4.1.2
The time since the ADSL line link up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

adslLineStatusAturInp 1.1.890.1.5.13.5.8.2.4.1.3
The upstream Impulse Noise Protection in unit of 0.1 DMT symbol.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

adslLineStatusAtucInp 1.1.890.1.5.13.5.8.2.4.1.4
The downstream Impulse Noise Protection in unit of 0.1 DMT symbol.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

powerMgmtParamTable 1.1.890.1.5.13.5.8.2.5
This table defines L0 to L2 power transition parameters. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PowerMgmtParamEntry

powerMgmtParamEntry 1.1.890.1.5.13.5.8.2.5.1
An entry in powerMgmtParamTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PowerMgmtParamEntry  

powerMgmtL0Time 1.1.890.1.5.13.5.8.2.5.1.1
The object specifies the minimum time in L0 mode before L2 mode may be entered.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

powerMgmtL2Time 1.1.890.1.5.13.5.8.2.5.1.2
The object specifies the minimum time in L2 mode before trimming and in between power trims.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

powerMgmtL2Atpr 1.1.890.1.5.13.5.8.2.5.1.3
The maximum aggregate transmit power.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

powerMgmtL2Atprt 1.1.890.1.5.13.5.8.2.5.1.4
The maximum total aggregate transmit power.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

powerMgmtL2MinRate 1.1.890.1.5.13.5.8.2.5.1.5
The object specifies the minimum L2 rate.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

powerMgmtL2MaxRate 1.1.890.1.5.13.5.8.2.5.1.6
The object specifies the maximum L2 rate.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

powerMgmtL2ThreshRate 1.1.890.1.5.13.5.8.2.5.1.7
The object specifies the rate threshold that triggers the line entering L0 or L2 mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

powerMgmtPSDTable 1.1.890.1.5.13.5.8.2.6
This table provides the PSD setting for both ATU-C and ATU-R. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PowerMgmtPSDEntry

powerMgmtPSDEntry 1.1.890.1.5.13.5.8.2.6.1
An entry in powerMgmtPSDTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PowerMgmtPSDEntry  

powerMgmtAtucMaxPSD 1.1.890.1.5.13.5.8.2.6.1.1
The object specifies the maximum ATU-C PSD.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

powerMgmtAturMaxPSD 1.1.890.1.5.13.5.8.2.6.1.2
The object specifies the maximum ATU-R PSD.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

shdslLineConfTable 1.1.890.1.5.13.5.8.3.1
This table includes common attributes describing the SHDSL line.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ShdslLineConfEntry

shdslLineConfEntry 1.1.890.1.5.13.5.8.3.1.1
An entry in shdslLineConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ShdslLineConfEntry  

shdslLineConfShdslMode 1.1.890.1.5.13.5.8.3.1.1.1
Mode of the SHDSL port. This MIB object is not supported by R5.03 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER stuc(1), stur(2)  

shdslLineConfPmms 1.1.890.1.5.13.5.8.3.1.1.2
Negotiated noise margin mode of the SHDSL port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), forced(2)  

shdslLineConfPboMode 1.1.890.1.5.13.5.8.3.1.1.3
Power backoff mode of the SHDSL port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal-epl(1), forced-epl(2), forced-no-epl(3)  

shdslLineConfPboValue 1.1.890.1.5.13.5.8.3.1.1.4
Power backoff value of the SHDSL port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..31  

shdslLineConfModulation 1.1.890.1.5.13.5.8.3.1.1.5
Modulation mode of the SHDSL port. This MIB object is supported by R5.03 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER auto(1), pam16(2), pam32(3)  

shdslLineConfTCMode 1.1.890.1.5.13.5.8.3.1.1.6
Transmission Convergence layer. This MIB object is supported by R5.05 and later versions. 1: atm 2: efm
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER atm(1), efm(2)  

shdslPortBatchSet 1.1.890.1.5.13.5.8.3.2
OBJECT IDENTIFIER    

shdslPortTarget 1.1.890.1.5.13.5.8.3.2.1
The managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 Byte 2~4: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8, and the second octet specifying slots 9 through 16, and so on. Byte 5~: each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

shdslPortOps 1.1.890.1.5.13.5.8.3.2.2
The managed object is for SHDSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: enable port BIT 2: disable port BIT 3: set SHDSL mode BIT 4: set line profile BIT 5: set alarm profile BIT 6: set pmms mode to be normal BIT 7: set pmms mode to be forced BIT 8: set pbo mode to be normal-epl BIT 9: set pbo mode to be forced-epl BIT 10: set pbo mode to be forced-no-epl BIT 11: set pbo value
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

shdslModeForBatchSet 1.1.890.1.5.13.5.8.3.2.3
Mode of the SHDSL port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER stuc(1), stur(2)  

shdslLineProfileForBatchSet 1.1.890.1.5.13.5.8.3.2.4
The SHDSL line profile.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

shdslAlarmProfileForBatchSet 1.1.890.1.5.13.5.8.3.2.5
The SHDSL alarm profile.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

shdslPboValueForBatchSet 1.1.890.1.5.13.5.8.3.2.6
Power backoff value of the SHDSL port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..31  

shdslLineStatusTable 1.1.890.1.5.13.5.8.3.3
This table includes the SHDSL line status.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ShdslLineStatusEntry

shdslLineStatusEntry 1.1.890.1.5.13.5.8.3.3.1
An entry in shdslLineStatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ShdslLineStatusEntry  

shdslLineStatusWirePair 1.1.890.1.5.13.5.8.3.3.1.1
The link-up wire pair of the SHDSL line.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER twoWire(1), fourWire(2), mpair4(4)  

maxNumOfPvcs 1.1.890.1.5.13.5.8.4.1
The maximum number of PVCs which could be created on a port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

pvcTable 1.1.890.1.5.13.5.8.4.2
This table includes PVC configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PvcEntry

pvcEntry 1.1.890.1.5.13.5.8.4.2.1
An entry in pvcTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PvcEntry  

pvcVpi 1.1.890.1.5.13.5.8.4.2.1.1
VPI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

pvcVci 1.1.890.1.5.13.5.8.4.2.1.2
VCI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

pvcPvid 1.1.890.1.5.13.5.8.4.2.1.3
Default VID of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

pvcEncap 1.1.890.1.5.13.5.8.4.2.1.4
Encapsulation of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER llc(1), vc(2), auto(3)  

pvcPriority 1.1.890.1.5.13.5.8.4.2.1.5
802.1p default priority of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

pvcProfile 1.1.890.1.5.13.5.8.4.2.1.6
The value of this object identifies the row in the atmProfileTable, which applies for this pvc.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

pvcRowStatus 1.1.890.1.5.13.5.8.4.2.1.7
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

pvcMvlanEnable 1.1.890.1.5.13.5.8.4.2.1.8
Enable/disable multicast VLAN function for the PVC. This object is supported by R1.02 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

pvcAcName 1.1.890.1.5.13.5.8.4.2.1.9
Access concentrator name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

pvcServiceName 1.1.890.1.5.13.5.8.4.2.1.10
Service name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

pvcHelloTime 1.1.890.1.5.13.5.8.4.2.1.11
The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

pvcVlanTable 1.1.890.1.5.13.5.8.4.3
This table includes the VLAN configuration for each PVC.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PvcVlanEntry

pvcVlanEntry 1.1.890.1.5.13.5.8.4.3.1
An entry in pvcVlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PvcVlanEntry  

pvcVlanReg 1.1.890.1.5.13.5.8.4.3.1.1
The PVC is egress or forbidden for this VLAN.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER egress(1), forbidden(2)  

pvcVlanTag 1.1.890.1.5.13.5.8.4.3.1.2
The PVC should transmit egress packets for this VLAN as tagged or untagged.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER tag(1), untag(2)  

pvcVlanRowStatus 1.1.890.1.5.13.5.8.4.3.1.3
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

pvcUsRateLimitTable 1.1.890.1.5.13.5.8.4.4
This table defines the upstream rate limit for each PVC. This table is supported by R1.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PvcUsRateLimitEntry

pvcUsRateLimitEntry 1.1.890.1.5.13.5.8.4.4.1
An entry in pvcUsRateLimitTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PvcUsRateLimitEntry  

pvcUsRateLimitEnable 1.1.890.1.5.13.5.8.4.4.1.1
Enable/disable upstream rate limit for a PVC.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

pvcUsRateLimit 1.1.890.1.5.13.5.8.4.4.1.2
Upstream rate limit in Kbps for a PVC.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

maxNumOfPriorityPvcs 1.1.890.1.5.13.5.8.5.1
The maximum number of priority PVCs which could be created on a port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ppvcTable 1.1.890.1.5.13.5.8.5.2
This table includes priority PVC configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PpvcEntry

ppvcEntry 1.1.890.1.5.13.5.8.5.2.1
An entry in ppvcTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PpvcEntry  

ppvcVpi 1.1.890.1.5.13.5.8.5.2.1.1
VPI of the ppvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

ppvcVci 1.1.890.1.5.13.5.8.5.2.1.2
VCI of the ppvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

ppvcPvid 1.1.890.1.5.13.5.8.5.2.1.3
Default VID of the ppvc.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

ppvcEncap 1.1.890.1.5.13.5.8.5.2.1.4
Encapsulation of the ppvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER llc(1), vc(2)  

ppvcPriority 1.1.890.1.5.13.5.8.5.2.1.5
802.1p default priority of the ppvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

ppvcRowStatus 1.1.890.1.5.13.5.8.5.2.1.6
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ppvcVlanTable 1.1.890.1.5.13.5.8.5.3
This table includes the VLAN configuration for each priority PVC.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PpvcVlanEntry

ppvcVlanEntry 1.1.890.1.5.13.5.8.5.3.1
An entry in ppvcVlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PpvcVlanEntry  

ppvcVlanReg 1.1.890.1.5.13.5.8.5.3.1.1
The PVC is egress or forbidden for this VLAN.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER egress(1), forbidden(2)  

ppvcVlanTag 1.1.890.1.5.13.5.8.5.3.1.2
The PVC should transmit egress packets for this VLAN as tagged or untagged.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER tag(1), untag(2)  

ppvcVlanRowStatus 1.1.890.1.5.13.5.8.5.3.1.3
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ppvcMemberTable 1.1.890.1.5.13.5.8.5.4
This table includes priority PVC member configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PpvcMemberEntry

ppvcMemberEntry 1.1.890.1.5.13.5.8.5.4.1
An entry in ppvcMemberTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PpvcMemberEntry  

ppvcMemberVpi 1.1.890.1.5.13.5.8.5.4.1.1
VPI of the member ppvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

ppvcMemberVci 1.1.890.1.5.13.5.8.5.4.1.2
VCI of the member ppvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

ppvcMemberPriority 1.1.890.1.5.13.5.8.5.4.1.3
802.1p default priority of the member ppvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..7  

ppvcMemberProfile 1.1.890.1.5.13.5.8.5.4.1.4
The profile of the member ppvc.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

ppvcMemberRowStatus 1.1.890.1.5.13.5.8.5.4.1.5
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

portTarget 1.1.890.1.5.13.5.8.6.1
The managed object is used for identify the target on which the port configuration should be performed. The target is encoded as: Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 Byte 2~4: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8, and the second octet specifying slots 9 through 16, and so on. Byte 5~: each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

portOps 1.1.890.1.5.13.5.8.6.2
The managed object is for xDSL line configuration. When the EMS wants to issue the desired operation, the EMS shall send SNMP-SET message to set the corresponding bit value to be 1. The various bit positions are: BIT 1: enable port BIT 2: disable port BIT 3: reserved BIT 4: default port settings
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

pvcStatsTable 1.1.890.1.5.13.5.8.7.1
This table includes PVC statistics.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PvcStatsEntry

pvcStatsEntry 1.1.890.1.5.13.5.8.7.1.1
An entry in pvcStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PvcStatsEntry  

pvcStatsTxRate 1.1.890.1.5.13.5.8.7.1.1.1
Transmission Rate (byte/sec) on the PVC.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

pvcStatsRxRate 1.1.890.1.5.13.5.8.7.1.1.2
Receive rate (byte/sec) on the PVC.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

pvcStatsTxCells 1.1.890.1.5.13.5.8.7.1.1.3
The number of transmitted cells on the PVC since last counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

pvcStatsRxCells 1.1.890.1.5.13.5.8.7.1.1.4
The number of received packets on the PVC since last counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

pvcStatsCrcErrors 1.1.890.1.5.13.5.8.7.1.1.5
The number of detected CRC errors on the PVC since last counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

pvcStatsTxPackets 1.1.890.1.5.13.5.8.7.1.1.6
This object is supported by R1.02 and later versions. The number of transmitted packets on the PVC since last counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

pvcStatsRxPackets 1.1.890.1.5.13.5.8.7.1.1.7
This object is supported by R1.02 and later versions. The number of received packets on the PVC since last counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

pvcStatsTxUnicast 1.1.890.1.5.13.5.8.7.1.1.8
This object is supported by R1.02 and later versions. The number of transmitted unicast packets on the PVC since last counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

pvcStatsRxUnicast 1.1.890.1.5.13.5.8.7.1.1.9
This object is supported by R1.02 and later versions. The number of received unicast packets on the PVC since last counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

pvcStatsTxMulticast 1.1.890.1.5.13.5.8.7.1.1.10
This object is supported by R1.02 and later versions. The number of transmitted multicast packets on the PVC since last counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

pvcStatsRxMulticast 1.1.890.1.5.13.5.8.7.1.1.11
This object is supported by R1.02 and later versions. The number of received multicast packets on the PVC since last counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

pvcStatsTxBroadcast 1.1.890.1.5.13.5.8.7.1.1.12
This object is supported by R1.02 and later versions. The number of transmitted broadcast packets on the PVC since last counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

pvcStatsRxBroadcast 1.1.890.1.5.13.5.8.7.1.1.13
This object is supported by R1.02 and later versions. The number of received broadcast packets on the PVC since last counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

pvcStatsTxDiscard 1.1.890.1.5.13.5.8.7.1.1.14
This object is supported by R1.02 and later versions. The number of discarded packets when transmitted on the PVC since last counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

pvcStatsRxDiscard 1.1.890.1.5.13.5.8.7.1.1.15
This object is supported by R1.02 and later versions. The number of discarded packets when received on the PVC since last counter reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

pvcCounterIfIndex 1.1.890.1.5.13.5.8.7.2
IfIndex of the PVC whose counters would be reset.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

pvcCounterVpi 1.1.890.1.5.13.5.8.7.3
VPI of the PVC whose counters would be reset.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

pvcCounterVci 1.1.890.1.5.13.5.8.7.4
VCI of the PVC whose counters would be reset.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

pvcCounterReset 1.1.890.1.5.13.5.8.7.5
Set the object to 1 to reset PVC counters for the PVC which is identified by pvcCounterIfIndex, pvcCounterVpi, and pvcCounterVci.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

paepvcTable 1.1.890.1.5.13.5.8.8.1
This table includes PPPoAoE PVC configuration. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PaepvcEntry

paepvcEntry 1.1.890.1.5.13.5.8.8.1.1
An entry of paepvcTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PaepvcEntry  

paepvcVpi 1.1.890.1.5.13.5.8.8.1.1.1
VPI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

paepvcVci 1.1.890.1.5.13.5.8.8.1.1.2
VCI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

paepvcPvid 1.1.890.1.5.13.5.8.8.1.1.3
Default VID of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

paepvcEncap 1.1.890.1.5.13.5.8.8.1.1.4
Encapsulation of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER llc(1), vc(2)  

paepvcPriority 1.1.890.1.5.13.5.8.8.1.1.5
802.1p default priority of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

paepvcProfile 1.1.890.1.5.13.5.8.8.1.1.6
The value of this object identifies the row in the atmProfileTable, which applies for this pvc.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

paepvcAcName 1.1.890.1.5.13.5.8.8.1.1.7
Access concentrator name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

paepvcServiceName 1.1.890.1.5.13.5.8.8.1.1.8
Service name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

paepvcHelloTime 1.1.890.1.5.13.5.8.8.1.1.9
The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

paepvcRowStatus 1.1.890.1.5.13.5.8.8.1.1.10
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tlspvcTable 1.1.890.1.5.13.5.8.9.1
This table includes Transparent LAN Service (TLS) PVC configuration. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TlspvcEntry

tlspvcEntry 1.1.890.1.5.13.5.8.9.1.1
An entry of tlspvcTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  TlspvcEntry  

tlspvcVpi 1.1.890.1.5.13.5.8.9.1.1.1
VPI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

tlspvcVci 1.1.890.1.5.13.5.8.9.1.1.2
VCI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

tlspvcSvid 1.1.890.1.5.13.5.8.9.1.1.3
s-tag VLAN ID of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

tlspvcEncap 1.1.890.1.5.13.5.8.9.1.1.4
Encapsulation of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER llc(1), vc(2)  

tlspvcSpriority 1.1.890.1.5.13.5.8.9.1.1.5
s-tag priority of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

tlspvcProfile 1.1.890.1.5.13.5.8.9.1.1.6
The value of this object identifies the row in the atmProfileTable, which applies for this pvc.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

tlspvcRowStatus 1.1.890.1.5.13.5.8.9.1.1.7
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vdslLineConfTable 1.1.890.1.5.13.5.8.10.1
This table includes common attributes describing the VDSL line. This table is supported by R2.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineConfEntry

vdslLineConfEntry 1.1.890.1.5.13.5.8.10.1.1
An entry in vdslLineConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineConfEntry  

vdslLineConfUpbo 1.1.890.1.5.13.5.8.10.1.1.1
Enable/disable upstream power backoff control.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

vdslLineConfVdslProfile 1.1.890.1.5.13.5.8.10.1.1.2
Set VDSL profile.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER vdsl-8a(1), vdsl-8b(2), vdsl-8c(3), vdsl-8d(4), vdsl-12a(5), vdsl-12b(6), vdsl-17a(7), auto(8), adsl2plus(9), vdsl2(10)  

vdslLineConfFrequencyPlan 1.1.890.1.5.13.5.8.10.1.1.3
Set VDSL frequency plan.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER plan997(1), plan998(2)  

vdslLineConfRfiBand 1.1.890.1.5.13.5.8.10.1.1.4
Set VDSL customized RFI configuration. disable: not apply RFI notch to port ansi: use pre-defined ANSI RFI notch etsi: use pre-defined ETSI notch custom: user needs to define customized RFI notch band through vdslRfiCustomTable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), ansi(2), etsi(3), custom(4)  

vdslLineConfIpqosProfile 1.1.890.1.5.13.5.8.10.1.1.5
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

vdslLineConfVturInp 1.1.890.1.5.13.5.8.10.1.1.6
This object is supported by R5.01 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..160  

vdslLineConfVtucInp 1.1.890.1.5.13.5.8.10.1.1.7
This object is supported by R5.01 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..160  

vdslLineConfOptionMask 1.1.890.1.5.13.5.8.10.1.1.8
This object is supported by R5.01 and later versions. Bit1: disable Trellis coding in ADSL mode Bit2: disable Reed-Solomon coding for ADSL Bit3: disable upstream bitswaps Bit4: disable downstream bitwaps Bit5: disable upstream 1-bit constellation support Bit6: disable the transmit windowing in ADSL2+ mode Bit7: disable S=0.5 support in G.dmt Bit8: reserved Bit9: enable nitro Bit12: enable US PTM optimization Bit13: enable DS PTM optimization Bit14: enable US PHYR Bit15: enable DS PHYR
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

vdslLineConfUpboForceLength 1.1.890.1.5.13.5.8.10.1.1.9
-1 means auto electric length. This object is supported by R5.01 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..1270  

vdslLineConfPsdShape 1.1.890.1.5.13.5.8.10.1.1.10
This object is supported by R5.01 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER vdsl2-a-nus0(1), vdsl2-a-eu32(2), vdsl2-a-eu36(3), vdsl2-a-eu40(4), vdsl2-a-eu44(5), vdsl2-a-eu48(6), vdsl2-a-eu52(7), vdsl2-a-eu56(8), vdsl2-a-eu60(9), vdsl2-a-eu64(10), vdsl2-a-eu128(11), vdsl1-fttex-ansi-m1(12), vdsl1-fttex-ansi-m2(13), vdsl1-fttcab-ansi-m1(14), vdsl1-fttcab-ansi-m2(15), vdsl1-fttex-ansi-m1-e(16), vdsl1-fttex-ansi-m2-e(17), vdsl-fttcab-ansi-m1-e(18), vdsl-fttcab-ansi-m2-e(19), vdsl2-a-ct(20), vdsl2-b8-1(21), vdsl2-b8-2(22), vdsl2-b8-3(23), vdsl2-b8-4(24), vdsl2-b8-5(25), vdsl2-b8-6(26), vdsl2-b8-7(27), vdsl2-b8-8(28), vdsl2-b8-9(29), vdsl2-b8-10(30), vdsl2-b8-11(31), vdsl2-b8-12(32), vdsl2-b8-13(33), vdsl2-b8-14(34), vdsl2-b8-15(35), vdsl2-b8-16(36), vdsl2-b7-1(37), vdsl2-b7-2(38), vdsl2-b7-3(39), vdsl2-b7-4(40), vdsl2-b7-5(41), vdsl2-b7-6(42), vdsl2-b7-7(43), vdsl2-b7-8(44), vdsl2-b7-9(45), vdsl2-b7-10(46), vdsl2-bt-anfp(47), vdsl2-c-138-b(48), vdsl2-c-276-b(49), vdsl2-c-138-co(50), vdsl2-c-276-co(51)  

vdslLineConfDpbo 1.1.890.1.5.13.5.8.10.1.1.11
This object is supported by R5.01 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

vdslLineConfDpboParamEsel 1.1.890.1.5.13.5.8.10.1.1.12
This object is supported by R5.01 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..511  

vdslLineConfDpboParamEscma 1.1.890.1.5.13.5.8.10.1.1.13
-1~-1.5 in step of 1/256. This object is supported by R5.01 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..640  

vdslLineConfDpboParamEscmb 1.1.890.1.5.13.5.8.10.1.1.14
-1~-1.5 in step of 1/256. This object is supported by R5.01 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..640  

vdslLineConfDpboParamEscmc 1.1.890.1.5.13.5.8.10.1.1.15
-1~-1.5 in step of 1/256. This object is supported by R5.01 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..640  

vdslLineConfDpboParamMus 1.1.890.1.5.13.5.8.10.1.1.16
This object is supported by R5.01 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

vdslLineConfDpboParamFmin 1.1.890.1.5.13.5.8.10.1.1.17
This object is supported by R5.01 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..2048  

vdslLineConfDpboParamFmax 1.1.890.1.5.13.5.8.10.1.1.18
This object is supported by R5.01 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 32..6956  

vdslLineConfDpboParamPsdId 1.1.890.1.5.13.5.8.10.1.1.19
Always return 0 when read. This object is supported by R5.01 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER psd-co(1), psd-flat(2), psd-cab-ansi(3), psd-cab-etsi(4), psd-exch-etsi(5), psd-exch-ansi(6), psd-default(100)  

vdslLineConfCompatible 1.1.890.1.5.13.5.8.10.1.1.20
Compatible to spectrum usage of adsl2 or adsl2+ line. The object is supported by R5.02 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), adsl2(2), adsl2Plus(3)  

vdslLineConfPowerMode 1.1.890.1.5.13.5.8.10.1.1.21
The power mode of the VDSL line. This MIB object is supported by R5.05 and later versions. 1: fix 2: priorityToPower 3: priorityToRate
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fix(1), priorityToPower(2), priorityToRate(3)  

vdslLineConfVturMaxTxPower 1.1.890.1.5.13.5.8.10.1.1.22
The maximum allowed transmit power of VTU-R. -130~200
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

vdslLineConfVtucMaxTxPower 1.1.890.1.5.13.5.8.10.1.1.23
The maximum allowed transmit power of VTU-C. -50~200
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

vdslLineConfMaxRxPower 1.1.890.1.5.13.5.8.10.1.1.24
The maximum aggregate received power. -255~255
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

vdslLineConfPMask 1.1.890.1.5.13.5.8.10.1.1.25
To configure a bit mask to select preferred protocols : 0x00000001~0xffffffff 0x00000001 G.992.1 A|B 0x00000002 G.992.2 A 0x00000004 G.992.3 A|B 0x00000010 G.992.5 A|B 0x00000020 ANSI T1.413 0x00000040 ETSI TS 101 388 0x00000080 G.993.2 8a 0x00000100 G.993.2 8b 0x00000200 G.993.2 8c 0x00000400 G.993.2 8d 0x00000800 G.993.2 12a 0x00001000 G.993.2 12b 0x00002000 G.993.2 17a 0x00004000 G.992.3 M 0x00008000 G.992.3 J 0x00010000 G.992.3 L 0x00020000 G.992.3 L Narrow PSD 0x00040000 G.992.5 M 0x00080000 G.992.5 J
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

vdslLineConfAturCarrierMask 1.1.890.1.5.13.5.8.10.1.1.26
Sub-carrier masking for ADSL2+ fallback, Upstream sub-carrier mask.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

vdslLineConfAtucCarrierMask0 1.1.890.1.5.13.5.8.10.1.1.27
Sub-carrier masking for ADSL2+ fallback, Downstream sub-carrier mask.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

vdslLineConfAtucCarrierMask1 1.1.890.1.5.13.5.8.10.1.1.28
Sub-carrier masking for ADSL2+ fallback, Downstream sub-carrier mask.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

vdslLineConfSnrModeDs 1.1.890.1.5.13.5.8.10.1.1.29
To enable the transmitter referred virtual noise in the downstream direction. 1: enable(1) 2: disable(2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

vdslLineConfSnrModeUs 1.1.890.1.5.13.5.8.10.1.1.30
To enable the transmitter referred virtual noise in the upstream direction. 1: enable(1) 2: disable(2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

vdslLineConfTxRefVnDs 1.1.890.1.5.13.5.8.10.1.1.31
To configure downstream transmitter referred virtual noise.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

vdslLineConfTxRefVnUs 1.1.890.1.5.13.5.8.10.1.1.32
To configure upstream transmitter referred virtual noise.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

vdslLineConfTpstcTypeAdsl 1.1.890.1.5.13.5.8.10.1.1.33
TPS-TC type for ADSL mode VLC. 1: atm(1) 2: ptm(2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER atm(1), ptm(2)  

vdslLineConfTpstcTypeVdsl 1.1.890.1.5.13.5.8.10.1.1.34
TPS-TC type for VDSL mode VLC. 1: atm(1) 2: ptm(2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER atm(1), ptm(2)  

vdslLineConfVturInmEq 1.1.890.1.5.13.5.8.10.1.1.35
The INM Inmpulse Noise Protection Equivalent Mode. Configuration parameter INM-INPEQ-MODE defines the way of computation of Equivalent INP, as defined in ITU-T G.993.2 Amd2 11.4.2.2.1. This takes a value in the range from 0 to 3.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..3  

vdslLineConfVtucInmEq 1.1.890.1.5.13.5.8.10.1.1.36
The INM Inmpulse Noise Protection Equivalent Mode. Configuration parameter INM-INPEQ-MODE defines the way of computation of Equivalent INP, as defined in ITU-T G.993.2 Amd2 11.4.2.2.1. This takes a value in the range from 0 to 3.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..3  

vdslLineConfInmVturCC 1.1.890.1.5.13.5.8.10.1.1.37
The INM Cluster Continuation. The valid values for INMCC range from 0 from 64 DMT symbols in steps of 1 DMT symbol. Up to and including INMCC nondegraded symbols will be allowed before a cluster is deemed to be complete and the impulse noise event over.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfInmVtucCC 1.1.890.1.5.13.5.8.10.1.1.38
The INM Cluster Continuation. The valid values for INMCC range from 0 from 64 DMT symbols in steps of 1 DMT symbol. Up to and including INMCC nondegraded symbols will be allowed before a cluster is deemed to be complete and the impulse noise event over.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfInmVturIATO 1.1.890.1.5.13.5.8.10.1.1.39
The INM Inter Arrival Time Offset for the IAT anomaly generation. The valid values for INMIATO range from 3 from 511 DMT symbols in steps of 1 DMT symbol.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfInmVtucIATO 1.1.890.1.5.13.5.8.10.1.1.40
The INM Inter Arrival Time Offset for the IAT anomaly generation. The valid values for INMIATO range from 3 from 511 DMT symbols in steps of 1 DMT symbol.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfInmVturIATS 1.1.890.1.5.13.5.8.10.1.1.41
The INM Inter Arrival Time Step for the IAT anomaly generation. The valid values for INMIATS range from 0 from 7 in steps. The range of values of inter-arrival times recorded in a single bin is 2^(INMIATS). All inter-arrival times greater than or equal to INMIATO+6*(2^INMIATS) are recorded in the 7th bin of INMAIAT.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfInmVtucIATS 1.1.890.1.5.13.5.8.10.1.1.42
The INM Inter Arrival Time Step for the IAT anomaly generation. The valid values for INMIATS range from 0 from 7 in steps. The range of values of inter-arrival times recorded in a single bin is 2^(INMIATS). All inter-arrival times greater than or equal to INMIATO+6*(2^INMIATS) are recorded in the 7th bin of INMAIAT.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfInmVtucISDBUS 1.1.890.1.5.13.5.8.10.1.1.43
ISDD sensitivity of VTU-C,-128~127 in unit of 0.1dB.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

vdslLineConfGinpRtxModeDs 1.1.890.1.5.13.5.8.10.1.1.44
G.inp(G.998.4) support setting on downstream direction. The possible values are: Forbidden(0) - Support for G998.4 is disabled. Preferred(1) - If G998.4 is supported by the far-end, it is enabled. Forced(2) - The line will only train if G998.4 can be enabled. Test(3) - G998.4 is enabled in test mode (refer to G998.4, Clause 10.4).
Status: current Access: read-write
OBJECT-TYPE    
  Xdsl2ConfigRtxMode  

vdslLineConfGinpRtxModeUs 1.1.890.1.5.13.5.8.10.1.1.45
G.inp(G.998.4) support setting on upstream direction. The possible values are: Forbidden(0) - Support for G998.4 is disabled. Preferred(1) - If G998.4 is supported by the far-end, it is enabled. Forced(2) - The line will only train if G998.4 can be enabled. Test(3) - G998.4 is enabled in test mode (refer to G998.4, Clause 10.4).
Status: current Access: read-write
OBJECT-TYPE    
  Xdsl2ConfigRtxMode  

vdslLineConfGinpEtrMaxDs 1.1.890.1.5.13.5.8.10.1.1.46
Defines the maximum allowed value for the ETR (Effective Throughput Rate).
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfGinpEtrMaxUs 1.1.890.1.5.13.5.8.10.1.1.47
Defines the maximum allowed value for the ETR (Effective Throughput Rate).
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfGinpEtrMinDs 1.1.890.1.5.13.5.8.10.1.1.48
Defines the minimum value for the ETR (Effective Throughput Rate).
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfGinpEtrMinUs 1.1.890.1.5.13.5.8.10.1.1.49
Defines the minimum value for the ETR (Effective Throughput Rate).
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfGinpNdrMaxDs 1.1.890.1.5.13.5.8.10.1.1.50
Overrules the wanted maximum data rate provided in the SetLineTrafficConfiguration
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfGinpNdrMaxUs 1.1.890.1.5.13.5.8.10.1.1.51
Overrules the wanted maximum data rate provided in the SetLineTrafficConfiguration
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfGinpShineRatioDs 1.1.890.1.5.13.5.8.10.1.1.52
The assumed fraction (0.001 to 0.255) of NDR necessary to correct SHINE noise.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfGinpShineRatioUs 1.1.890.1.5.13.5.8.10.1.1.53
The assumed fraction (0.001 to 0.255) of NDR necessary to correct SHINE noise.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfGinpLeftrThresholdDs 1.1.890.1.5.13.5.8.10.1.1.54
The rate threshold (fraction of NDR) below which the Low Error Free Rate (LEFTR) defect is declared.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfGinpLeftrThresholdUs 1.1.890.1.5.13.5.8.10.1.1.55
The rate threshold (fraction of NDR) below which the Low Error Free Rate (LEFTR) defect is declared.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfGinpMaxDelayDs 1.1.890.1.5.13.5.8.10.1.1.56
G.inp-specific value that overrules the traffic configuration setting.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfGinpMaxDelayUs 1.1.890.1.5.13.5.8.10.1.1.57
G.inp-specific value that overrules the traffic configuration setting.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfGinpMinDelayDs 1.1.890.1.5.13.5.8.10.1.1.58
G.inp-specific value that overrules the traffic configuration setting.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfGinpMinDelayUs 1.1.890.1.5.13.5.8.10.1.1.59
G.inp-specific value that overrules the traffic configuration setting.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfGinpInpMinDs 1.1.890.1.5.13.5.8.10.1.1.60
G.inp-specific value that overrules the traffic configuration setting. Unit is symbol. The possible values are: 0-31
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfGinpInpMinUs 1.1.890.1.5.13.5.8.10.1.1.61
G.inp-specific value that overrules the traffic configuration setting. Unit is symbol. The possible values are: 0-31
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfGinpReinCfgInpDs 1.1.890.1.5.13.5.8.10.1.1.62
G.inp-specific value that overrules the traffic configuration setting. Unit is symbol. The possible values are: 0-7
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfGinpReinCfgInpUs 1.1.890.1.5.13.5.8.10.1.1.63
G.inp-specific value that overrules the traffic configuration setting. Unit is symbol. The possible values are: 0-7
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfGinpReinCfgFreqDs 1.1.890.1.5.13.5.8.10.1.1.64
G.inp-specific value that overrules the traffic configuration setting. Unit is Hz. The possible values are: 100 - 100Hz 120 - 120Hz
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfGinpReinCfgFreqUs 1.1.890.1.5.13.5.8.10.1.1.65
G.inp-specific value that overrules the traffic configuration setting. Unit is Hz. The possible values are: 100 - 100Hz 120 - 120Hz
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfSosMinRateB0Ds 1.1.890.1.5.13.5.8.10.1.1.66
This parameter specifies the minimum net data rate required for a valid SOS request in the downstream direction. The value shall be coded as an unsigned integer representing the data rate as a multiple of 8 kbit/s.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfSosMinRateB0Us 1.1.890.1.5.13.5.8.10.1.1.67
This parameter specifies the minimum net data rate required for a valid SOS request in the upstream direction. The value shall be coded as an unsigned integer representing the data rate as a multiple of 8 kbit/s.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfSosTimeDs 1.1.890.1.5.13.5.8.10.1.1.68
The parameter SOS-TIME-ds is used in the specification of the receiver initiated SOS (see 13.4.3/G.993.2). If the value of this parameter is not zero, the standard SOS triggering criteria are enabled, and the value corresponds with duration of the time window used in the standard SOS triggering criteria in the downstream direction. See G.993.2 for detailed usage rules. The special value zero indicates that the standard SOS triggering criteria are disabled, i.e., vendor-discretionary values may be used instead of the values configured in the MIB for the following parameters: SOS-NTONES-ds, SOS-CRC-ds, SOS-TIME-ds. This parameter applies in the downstream direction. The valid range of non-zero values is from 64 ms to 16320 ms in steps of 64 ms.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfSosTimeUs 1.1.890.1.5.13.5.8.10.1.1.69
The parameter SOS-TIME-ds is used in the specification of the receiver initiated SOS (see 13.4.3/G.993.2). If the value of this parameter is not zero, the standard SOS triggering criteria are enabled, and the value corresponds with duration of the time window used in the standard SOS triggering criteria in the upstream direction. See G.993.2 for detailed usage rules. The special value zero indicates that the standard SOS triggering criteria are disabled, i.e., vendor-discretionary values may be used instead of the values configured in the MIB for the following parameters: SOS-NTONES-ds, SOS-CRC-ds, SOS-TIME-ds. This parameter applies in the upstream direction. The valid range of non-zero values is from 64 ms to 16320 ms in steps of 64 ms.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfSosCrcDs 1.1.890.1.5.13.5.8.10.1.1.70
This parameter is defined as the minimum number of normalized CRC anomalies received in SOS-TIME-ds seconds in order to arm the second sub condition of the standard SOS triggering criteria (see 13.4.3.2/G.993.2) in the downstream direction. See G.993.2 for detailed usage rules. The valid range of SOS-CRC values is 0.02 to ((2^16)-1)*0.02, in steps of 0.02.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfSosCrcUs 1.1.890.1.5.13.5.8.10.1.1.71
This parameter is defined as the minimum number of normalized CRC anomalies received in SOS-TIME-ds seconds in order to arm the second sub condition of the standard SOS triggering criteria (see 13.4.3.2/G.993.2) in the upstream direction. See G.993.2 for detailed usage rules. The valid range of SOS-CRC values is 0.02 to ((2^16)-1)*0.02, in steps of 0.02.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfSosNToneDs 1.1.890.1.5.13.5.8.10.1.1.72
This parameter is defined as the minimum percentage of tones in the downstream MEDLEY SET that must be degraded in order to arm the first sub-condition of the standard SOS triggering criteria (see 13.4.3.2/G.993.2) in the downstream direction. The parameter SOS-NTONES-ds is defined as a percentage of tones. See G.993.2 for detailed usage rules. The valid range of values is from 1 to 100 in steps of 1. Use of the special value 0 is described in 13.4.3.2/G.993.2.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfSosNToneUs 1.1.890.1.5.13.5.8.10.1.1.73
This parameter is defined as the minimum percentage of tones in the upstream MEDLEY SET that must be degraded in order to arm the first sub-condition of the standard SOS triggering criteria (see 13.4.3.2/G.993.2) in the upstream direction. The parameter SOS-NTONES-ds is defined as a percentage of tones. See G.993.2 for detailed usage rules. The valid range of values is from 1 to 100 in steps of 1. Use of the special value 0 is described in 13.4.3.2/G.993.2.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfSosMaxDs 1.1.890.1.5.13.5.8.10.1.1.74
This parameter is used in G.993.2 de-activation (see 12.1.4/G.993.2). If the number of successful SOS procedures in the downstream direction performed within a 120-second interval exceeds MAX-SOS-ds, the modem shall transition to the L3 state. See G.993.2 for detailed usage rules (see 12.1.4/G.993.2). The valid range of values is 1 to 15. Use of the special value 0 is described in 12.1/G.993.2.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfSosMaxUs 1.1.890.1.5.13.5.8.10.1.1.75
This parameter is used in G.993.2 de-activation (see 12.1.4/G.993.2). If the number of successful SOS procedures in the upstream direction performed within a 120-second interval exceeds MAX-SOS-ds, the modem shall transition to the L3 state. See G.993.2 for detailed usage rules (see 12.1.4/G.993.2). The valid range of values is 1 to 15. Use of the special value 0 is described in 12.1/G.993.2.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfSosMultiStepDs 1.1.890.1.5.13.5.8.10.1.1.76
Indicates the capabilities of the VTU-R to execute the SOS request in one step or in multiple steps in the downstream direction. The field is formatted as [gggg 0000]. The first four MSBs [gggg] indicate the maximum number of tones (GSOS) that can be executed in a single step (GSOS)in the downstream direction. The valid values are: - [0000]: No limitation - [0010]: GSOS = 256 tones - [0011]: GSOS = 512 tones - [0100]: GSOS = 1024 tones
Status: current Access: read-write
OBJECT-TYPE    
  BITS  

vdslLineConfSosMultiStepUs 1.1.890.1.5.13.5.8.10.1.1.77
Indicates the capabilities of the VTU-R to execute the SOS request in one step or in multiple steps in the upstream direction. The field is formatted as [gggg 0000]. The first four MSBs [gggg] indicate the maximum number of tones (GSOS) that can be executed in a single step (GSOS)in the upstream direction. The valid values are: - [0000]: No limitation - [0010]: GSOS = 256 tones - [0011]: GSOS = 512 tones - [0100]: GSOS = 1024 tones
Status: current Access: read-write
OBJECT-TYPE    
  BITS  

vdslLineConfRocEnableDs 1.1.890.1.5.13.5.8.10.1.1.78
Enable the robust overhead channel. disable(1), enable(2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

vdslLineConfRocEnableUs 1.1.890.1.5.13.5.8.10.1.1.79
Enable the robust overhead channel. disable(1), enable(2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

vdslLineConfRocSnrmDs 1.1.890.1.5.13.5.8.10.1.1.80
The parameter is defined as the SNR margin offset for the ROC channel in the downstream direction. The parameter is used in the specification of the channel initialization policy (see 12.3.7.1/G.993.2). The valid range of SNR margin offset values is from 0 to 31 dB with 0.1 dB steps.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfRocSnrmUs 1.1.890.1.5.13.5.8.10.1.1.81
The parameter is defined as the SNR margin offset for the ROC channel in the upstream direction. The parameter is used in the specification of the channel initialization policy (see 12.3.7.1/G.993.2). The valid range of SNR margin offset values is from 0 to 31 dB with 0.1 dB steps.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfRocMinInpDs 1.1.890.1.5.13.5.8.10.1.1.82
This parameter contains the minimum impulse noise protection to apply on the ROC in the downstream direction. The minimum impulse noise protection is an integer ranging from 0 to 16.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfRocMinInpUs 1.1.890.1.5.13.5.8.10.1.1.83
This parameter contains the minimum impulse noise protection to apply on the ROC in the upstream direction. The minimum impulse noise protection is an integer ranging from 0 to 16.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdslLineConfSosEnableDs 1.1.890.1.5.13.5.8.10.1.1.84
Enable the emergency rate reduction. disable(1), enable(2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

vdslLineConfSosEnableUs 1.1.890.1.5.13.5.8.10.1.1.85
Enable the emergency rate reduction. disable(1), enable(2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

vdslLineConfDynamicDepthDs 1.1.890.1.5.13.5.8.10.1.1.86
Enable the dynamic change of interleave depth.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

vdslLineConfDynamicDepthUs 1.1.890.1.5.13.5.8.10.1.1.87
Enable the dynamic change of interleave depth.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(1), enable(2)  

vdslLineConfDpboParamType 1.1.890.1.5.13.5.8.10.1.1.88
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER g9971(1), t-com(2)  

vdslLineConfDpboParamEselMin 1.1.890.1.5.13.5.8.10.1.1.89
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..511  

vdslLineConfHsTxA43Psd 1.1.890.1.5.13.5.8.10.1.1.90
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -128..-32  

vdslLineConfHsTxB43Psd 1.1.890.1.5.13.5.8.10.1.1.91
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -128..-32  

vdslLineConfHsTxA43cB43cPsd 1.1.890.1.5.13.5.8.10.1.1.92
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -128..-32  

vdslLineConfHsTxV43Carrier257Psd 1.1.890.1.5.13.5.8.10.1.1.93
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -128..-32  

vdslLineConfHsTxV43Carrier383Psd 1.1.890.1.5.13.5.8.10.1.1.94
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -128..-32  

vdslLineConfHsTxV43Carrier511Psd 1.1.890.1.5.13.5.8.10.1.1.95
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -128..-32  

vdslVlan 1.1.890.1.5.13.5.8.10.2
OBJECT IDENTIFIER    

vdslPortConfTable 1.1.890.1.5.13.5.8.10.2.1
This table includes common attributes describing the VDSL port. This table is supported by R2.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslPortConfEntry

vdslPortConfEntry 1.1.890.1.5.13.5.8.10.2.1.1
An entry in vdslPortConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslPortConfEntry  

vdslPortConfPvid 1.1.890.1.5.13.5.8.10.2.1.1.1
The PVID, the VLAN ID assigned to untagged frames or Priority-Tagged frames received on this port.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

vdslPortConfPriority 1.1.890.1.5.13.5.8.10.2.1.1.2
The default ingress User Priority for this port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

vdslPortConfAcceptableFrameType 1.1.890.1.5.13.5.8.10.2.1.1.3
When this is admitOnlyVlanTagged(2) the device will discard untagged frames or Priority-Tagged frames received on this port. When admitAll(1), untagged frames or Priority-Tagged frames received on this port will be accepted and assigned to the PVID for this port
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER admitAll(1), admitOnlyVlanTagged(2)  

vdslPortConfTlsEnable 1.1.890.1.5.13.5.8.10.2.1.1.4
Enable/disable the transparent LAN service.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

vdslPortConfTlsVid 1.1.890.1.5.13.5.8.10.2.1.1.5
The transparent LAN service s-tag VID.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

vdslPortConfTlsPriority 1.1.890.1.5.13.5.8.10.2.1.1.6
The transparent LAN service s-tag priority.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

vdslPortConfDtEnable 1.1.890.1.5.13.5.8.10.2.1.1.7
Enable/disable double tag service on the specified subscriber port. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

vdslPortConfDtSvid 1.1.890.1.5.13.5.8.10.2.1.1.8
The service provider VLAN ID. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

vdslPortConfDtSpriority 1.1.890.1.5.13.5.8.10.2.1.1.9
The service VLAN priority. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

vdslPortConfDtCvid 1.1.890.1.5.13.5.8.10.2.1.1.10
The system-side customer VID. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

vdslPortConfDtCpriority 1.1.890.1.5.13.5.8.10.2.1.1.11
The customer VLAN priority. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

vdslPortConfTlsPrioCopyEnable 1.1.890.1.5.13.5.8.10.2.1.1.12
Enable/disable the priority copy of TLS.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

vdslPortVlanTable 1.1.890.1.5.13.5.8.10.2.2
This table includes common attributes describing the VDSL port. This table is supported by R2.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslPortVlanEntry

vdslPortVlanEntry 1.1.890.1.5.13.5.8.10.2.2.1
An entry in vdslPortVlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslPortVlanEntry  

vdslPortVlanReg 1.1.890.1.5.13.5.8.10.2.2.1.1
The port is egress or forbidden for this VLAN.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER egress(1), forbidden(2)  

vdslPortVlanTag 1.1.890.1.5.13.5.8.10.2.2.1.2
The port should transmit egress packets for this VLAN as tagged or untagged.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER tag(1), untag(2)  

vdslPortVlanRowStatus 1.1.890.1.5.13.5.8.10.2.2.1.3
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vdslVlanStaticTable 1.1.890.1.5.13.5.8.10.2.3
A table containing static configuration information for each VLAN configured into the device by (local or network) management. All entries are permanent and will be restored after the device is reset. This table is supported by R2.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslVlanStaticEntry

vdslVlanStaticEntry 1.1.890.1.5.13.5.8.10.2.3.1
An entry in vdslVlanStaticTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslVlanStaticEntry  

vdslVlanStaticEgressPorts 1.1.890.1.5.13.5.8.10.2.3.1.1
The set of ports which are permanently assigned to the egress list for this VLAN by management.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

vdslVlanStaticUntaggedPorts 1.1.890.1.5.13.5.8.10.2.3.1.2
The set of ports which should transmit egress packets for this VLAN as untagged.
Status: current Access: read-create
OBJECT-TYPE    
  PortList  

vdslVlanStaticRowStatus 1.1.890.1.5.13.5.8.10.2.3.1.3
This object indicates the status of this entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vdslPortPvlanTable 1.1.890.1.5.13.5.8.10.2.4
This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslPortPvlanEntry

vdslPortPvlanEntry 1.1.890.1.5.13.5.8.10.2.4.1
An entry in vdslPortPvlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslPortPvlanEntry  

vdslPortPvlanEtype 1.1.890.1.5.13.5.8.10.2.4.1.1
0~0xffff.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslPortPvlanVid 1.1.890.1.5.13.5.8.10.2.4.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

vdslPortPvlanPriority 1.1.890.1.5.13.5.8.10.2.4.1.3
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

vdslPortPvlanRowStatus 1.1.890.1.5.13.5.8.10.2.4.1.4
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

vdslRfiCustomTable 1.1.890.1.5.13.5.8.10.3
This table includes VDSL customized RFI configuration. This table is supported by R2.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslRfiCustomEntry

vdslRfiCustomEntry 1.1.890.1.5.13.5.8.10.3.1
An entry in vdslRfiCustomTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslRfiCustomEntry  

vdslRfiCustomIndex 1.1.890.1.5.13.5.8.10.3.1.1
Index of the table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslRfiCustomStartFreq 1.1.890.1.5.13.5.8.10.3.1.2
The start value of the customized frequency range.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

vdslRfiCustomEndFreq 1.1.890.1.5.13.5.8.10.3.1.3
The end value of the customized frequency range.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

vdslRfiCustomEnable 1.1.890.1.5.13.5.8.10.3.1.4
Enable or disable the customized frequency range setting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

vdslRfiCustomMode 1.1.890.1.5.13.5.8.10.3.1.5
Notch : sent at -80 dBm in the specified frequency bands. Gap : cut the power completely in the specified frequency bands. 1: notch(1) 2: gap(2)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER notch(1), gap(2)  

vdslLineConfUpboParamTable 1.1.890.1.5.13.5.8.10.4
This table includes VDSL UPBO configuration. This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineConfUpboParamEntry

vdslLineConfUpboParamEntry 1.1.890.1.5.13.5.8.10.4.1
An entry in vdslLineConfUpboParamTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineConfUpboParamEntry  

vdslLineConfUpboParamBand 1.1.890.1.5.13.5.8.10.4.1.1
Index of the table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineConfUpboParamA 1.1.890.1.5.13.5.8.10.4.1.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 4000..8095  

vdslLineConfUpboParamB 1.1.890.1.5.13.5.8.10.4.1.3
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4095  

vdslLineConfDpboTable 1.1.890.1.5.13.5.8.10.5
This table includes VDSL DPBO configuration. This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineConfDpboEntry

vdslLineConfDpboEntry 1.1.890.1.5.13.5.8.10.5.1
An entry in vdslLineConfDpboTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineConfDpboEntry  

vdslLineConfDpboIndex 1.1.890.1.5.13.5.8.10.5.1.1
Index of the table.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineConfDpboTone 1.1.890.1.5.13.5.8.10.5.1.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..512  

vdslLineConfDpboPsd 1.1.890.1.5.13.5.8.10.5.1.3
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

ipbpvcDomainTable 1.1.890.1.5.13.5.8.11.1
This table includes ipbpvc domain configuration. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpbpvcDomainEntry

ipbpvcDomainEntry 1.1.890.1.5.13.5.8.11.1.1
An entry of ipbpvcDomainTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpbpvcDomainEntry  

ipbpvcDomainName 1.1.890.1.5.13.5.8.11.1.1.1
Name of the domain.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

ipbpvcDomainRowStatus 1.1.890.1.5.13.5.8.11.1.1.2
Row status of the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ipbpvcDomainVlanTable 1.1.890.1.5.13.5.8.11.2
This table includes ipbpvc domain VLAN configuration. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpbpvcDomainVlanEntry

ipbpvcDomainVlanEntry 1.1.890.1.5.13.5.8.11.2.1
An entry of ipbpvcDomainVlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpbpvcDomainVlanEntry  

ipbpvcDomainVlanId 1.1.890.1.5.13.5.8.11.2.1.1
Set VLAN to join or leave the specified domain.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

ipbpvcDomainDhcpVlanEnable 1.1.890.1.5.13.5.8.11.2.1.2
Enable/disable DHCP VLAN in a domain.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

ipbpvcDomainVlanRowStatus 1.1.890.1.5.13.5.8.11.2.1.3
Row status of the table used to create/delete an entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ipbpvcEdgeRouterTable 1.1.890.1.5.13.5.8.11.3
This table includes ipbpvc edge router configuration. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpbpvcEdgeRouterEntry

ipbpvcEdgeRouterEntry 1.1.890.1.5.13.5.8.11.3.1
An entry of ipbpvcEdgeRouterTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpbpvcEdgeRouterEntry  

ipbpvcEdgeRouterIp 1.1.890.1.5.13.5.8.11.3.1.1
IP address of the edge router.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

ipbpvcEdgeRouterVid 1.1.890.1.5.13.5.8.11.3.1.2
VLAN ID of the edge router.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

ipbpvcEdgeRouterMask 1.1.890.1.5.13.5.8.11.3.1.3
Netmask of the edge router.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcEdgeRouterRowStatus 1.1.890.1.5.13.5.8.11.3.1.4
Row status of the table used to create/delete an entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ipbpvcInterfaceTable 1.1.890.1.5.13.5.8.11.4
This table includes ipbpvc interface configuration. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpbpvcInterfaceEntry

ipbpvcInterfaceEntry 1.1.890.1.5.13.5.8.11.4.1
An entry of ipbpvcInterfaceTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpbpvcInterfaceEntry  

ipbpvcInterfaceIp 1.1.890.1.5.13.5.8.11.4.1.1
IP address of the interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

ipbpvcInterfaceMask 1.1.890.1.5.13.5.8.11.4.1.2
Netmask of the interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcInterfaceVid 1.1.890.1.5.13.5.8.11.4.1.3
VLAN ID of the interface.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

ipbpvcInterfaceIfIndex 1.1.890.1.5.13.5.8.11.4.1.4
IfIndex of the interface.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

ipbpvcInterfaceVpi 1.1.890.1.5.13.5.8.11.4.1.5
VPI of the interface.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

ipbpvcInterfaceVci 1.1.890.1.5.13.5.8.11.4.1.6
VCI of the interface.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

ipbpvcInterfaceRowStatus 1.1.890.1.5.13.5.8.11.4.1.7
Row status of the table used to create/delete an entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ipbpvcRouteTable 1.1.890.1.5.13.5.8.11.5
This table includes ipbpvc route configuration. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpbpvcRouteEntry

ipbpvcRouteEntry 1.1.890.1.5.13.5.8.11.5.1
An entry of ipbpvcRouteTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpbpvcRouteEntry  

ipbpvcRouteIp 1.1.890.1.5.13.5.8.11.5.1.1
IP address of the route.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

ipbpvcRouteMask 1.1.890.1.5.13.5.8.11.5.1.2
Netmask of the route.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcRouteNextHop 1.1.890.1.5.13.5.8.11.5.1.3
Next hop IP address of the route.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

ipbpvcRouteMetric 1.1.890.1.5.13.5.8.11.5.1.4
Metric of the route.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..15  

ipbpvcRoutePriority 1.1.890.1.5.13.5.8.11.5.1.5
Priority of the route. Note that the default value of this object is 8, which means we keep the original priority of the packet(frame).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

ipbpvcRouteRowStatus 1.1.890.1.5.13.5.8.11.5.1.6
Row status of the table used to create/delete an entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ipbpvcTable 1.1.890.1.5.13.5.8.11.6
This table includes ipbpvc configuration. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpbpvcEntry

ipbpvcEntry 1.1.890.1.5.13.5.8.11.6.1
An entry of ipbpvcTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpbpvcEntry  

ipbpvcVpi 1.1.890.1.5.13.5.8.11.6.1.1
VPI of the PVC.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcVci 1.1.890.1.5.13.5.8.11.6.1.2
VCI of the PVC.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcPvid 1.1.890.1.5.13.5.8.11.6.1.3
PVID of the PVC.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcEncap 1.1.890.1.5.13.5.8.11.6.1.4
Type of the PVC.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER llc(1), vc(2), llc-r(3), vc-r(4)  

ipbpvcPriority 1.1.890.1.5.13.5.8.11.6.1.5
Priority of the PVC.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

ipbpvcProfile 1.1.890.1.5.13.5.8.11.6.1.6
Profile of the PVC.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

ipbpvcRowStatus 1.1.890.1.5.13.5.8.11.6.1.7
Row status of the table used to create/delete an entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ipbpvcVlanTable 1.1.890.1.5.13.5.8.11.7
This table includes ipbpvc VLAN configuration. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpbpvcVlanEntry

ipbpvcVlanEntry 1.1.890.1.5.13.5.8.11.7.1
An entry of ipbpvcVlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpbpvcVlanEntry  

ipbpvcVlanReg 1.1.890.1.5.13.5.8.11.7.1.1
The PVC is egress or forbidden for this VLAN.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER egress(1), forbidden(2)  

ipbpvcVlanTag 1.1.890.1.5.13.5.8.11.7.1.2
The PVC should transmit egress packets for this VLAN as tagged or untagged.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER tag(1), untag(2)  

ipbpvcVlanRowStatus 1.1.890.1.5.13.5.8.11.7.1.3
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

arpproxy 1.1.890.1.5.13.5.8.11.8
OBJECT IDENTIFIER    

arpproxyAge 1.1.890.1.5.13.5.8.11.8.1
Aging time of the ARP proxy. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 10..10000  

arpproxyFlush 1.1.890.1.5.13.5.8.11.8.2
OBJECT IDENTIFIER    

arpproxyFlushTarget 1.1.890.1.5.13.5.8.11.8.2.1
The target whose ARP table to be flushed. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER all(1), edgerouter(2), interface(3)  

arpproxyFlushOps 1.1.890.1.5.13.5.8.11.8.2.2
Set the object to 1 to start flushing. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

arpproxyFlushEdgeRouterIp 1.1.890.1.5.13.5.8.11.8.2.3
Flush ARP table for the specified edge router. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

arpproxyFlushEdgeRouterVid 1.1.890.1.5.13.5.8.11.8.2.4
Flush ARP table for the specified edge router. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

arpproxyFlushInterfaceIp 1.1.890.1.5.13.5.8.11.8.2.5
Flush ARP table for the specified interface. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

arpproxyFlushInterfaceMask 1.1.890.1.5.13.5.8.11.8.2.6
Flush ARP table for the specified interface. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

arpproxyFlushInterfaceVid 1.1.890.1.5.13.5.8.11.8.2.7
Flush ARP table for the specified interface. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

voipSipLineConfTable 1.1.890.1.5.13.5.8.12.1
This table includes common attributes describing the VoIP line.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipSipLineConfEntry

voipSipLineConfEntry 1.1.890.1.5.13.5.8.12.1.1
An entry in voipSipLineConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipSipLineConfEntry  

voipSipLineConfSipProfile 1.1.890.1.5.13.5.8.12.1.1.1
SIP profile name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipSipLineConfSipCallSvcProfile 1.1.890.1.5.13.5.8.12.1.1.2
SIP call service profile name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipSipLineConfDspProfile 1.1.890.1.5.13.5.8.12.1.1.3
DSP profile name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipSipLineConfAccount 1.1.890.1.5.13.5.8.12.1.1.4
Account for SIP registration. This object is supported by R5.05 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipSipLineConfPassword 1.1.890.1.5.13.5.8.12.1.1.5
Password for SIP registration. This object is supported by R5.05 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipSipLineConfDataProfile 1.1.890.1.5.13.5.8.12.1.1.6
DSP profile name of data mode, up to 31 characters.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipPortH248 1.1.890.1.5.13.5.8.12.2
OBJECT IDENTIFIER    

voipH248LineConfTable 1.1.890.1.5.13.5.8.12.2.1
This table includes common attributes describing the VoIP line. This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipH248LineConfEntry

voipH248LineConfEntry 1.1.890.1.5.13.5.8.12.2.1.1
An entry in voipH248LineConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipH248LineConfEntry  

voipH248LineConfMgName 1.1.890.1.5.13.5.8.12.2.1.1.1
MG name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipH248LineConfDspProfile 1.1.890.1.5.13.5.8.12.2.1.1.2
DSP profile.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipH248LineConfDataProfile 1.1.890.1.5.13.5.8.12.2.1.1.3
DSP profile name of data mode, up to 31 characters. This MIB object is supported by R5.06 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipH248TerminationTable 1.1.890.1.5.13.5.8.12.2.2
This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipH248TerminationEntry

voipH248TerminationEntry 1.1.890.1.5.13.5.8.12.2.2.1
An entry in voipH248TerminationTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipH248TerminationEntry  

voipH248TerminationName 1.1.890.1.5.13.5.8.12.2.2.1.1
Termination name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipPotsImpedanceConfTable 1.1.890.1.5.13.5.8.12.3
This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipPotsImpedanceConfEntry

voipPotsImpedanceConfEntry 1.1.890.1.5.13.5.8.12.3.1
An entry in voipPotsImpedanceConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipPotsImpedanceConfEntry  

voipPotsImpedance 1.1.890.1.5.13.5.8.12.3.1.1
Default impedance is from impedance of country code.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER impedance-600ohm(0), impedance-600ohm-1000nf(1), impedance-220ohm-820ohm-120nf(2), impedance-270ohm-750ohm-150nf(3), impedance-300ohm-1000ohm-220nf(4), impedance-370ohm-620ohm-310nf(5), impedance-220ohm-680ohm-100nf(6), impedance-220ohm-820ohm-115nf(7), impedance-900ohm(8), impedance-200ohm-680ohm-100nf(9), impedance-900ohm-2160nf(10), default(255)  

voipPotsGainConfTable 1.1.890.1.5.13.5.8.12.4
This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipPotsGainConfEntry

voipPotsGainConfEntry 1.1.890.1.5.13.5.8.12.4.1
An entry in voipPotsGainConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipPotsGainConfEntry  

voipPotsTxGain 1.1.890.1.5.13.5.8.12.4.1.1
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -200..200  

voipPotsRxGain 1.1.890.1.5.13.5.8.12.4.1.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -200..200  

voipPotsDataTxGain 1.1.890.1.5.13.5.8.12.4.1.3
This MIB object is supported by R5.06 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -200..200  

voipPotsDataRxGain 1.1.890.1.5.13.5.8.12.4.1.4
This MIB object is supported by R5.06 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -200..200  

voipOpmodeConfTable 1.1.890.1.5.13.5.8.12.5
This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipOpmodeConfEntry

voipOpmodeConfEntry 1.1.890.1.5.13.5.8.12.5.1
An entry in voipOpmodeConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipOpmodeConfEntry  

voipOpMode 1.1.890.1.5.13.5.8.12.5.1.1
Configure operation mode to specified subscribers. Default is normal SIP server and v5sip is V5.2 access gateway.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER default(0), v5sip(1)  

voipPolarityReverseConfTable 1.1.890.1.5.13.5.8.12.6
This table is supported by R5.05 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipPolarityReverseConfEntry

voipPolarityReverseConfEntry 1.1.890.1.5.13.5.8.12.6.1
An entry in voipPolarityReverseConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipPolarityReverseConfEntry  

voipPolarityReverse 1.1.890.1.5.13.5.8.12.6.1.1
Enable/disable polarity reverse function. Polarity reverse is feature to reversed tip and ring after call establish and terminate.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

voipPotsCidConfTable 1.1.890.1.5.13.5.8.12.7
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipPotsCidConfEntry

voipPotsCidConfEntry 1.1.890.1.5.13.5.8.12.7.1
An entry in voipPotsCidConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipPotsCidConfEntry  

voipPotsCidASType 1.1.890.1.5.13.5.8.12.7.1.1
0: DEFVAL (use the setting of country code) 1: CID during ring 2: DTAS CID before ring 3: RPAS CID before ring 4: LR DTAS CID before ring 5: LR CID before ring 6: CID before ring
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER defval(0), cid-during-ring(1), dtas-cid-before-ring(2), rpas-cid-before-ring(3), lr-dtas-cid-before-ring(4), lr-cid-before-ring(5)  

voipPotsCidPayloadType 1.1.890.1.5.13.5.8.12.7.1.2
0: DEFVAL (use the setting of country code) 1: MDMF 2: SDMF 3: ETSI MDMF 4: ETSI SDMF 5: DTMF 6: UK MDMF 7: UK SDMF 8: Japanese MDMF
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER defval(0), mdmf(1), sdmf(2), etsi-mdmf(3), etsi-sdmf(4), dtmf(5), uk-mdmf(6), uk-sdmf(7), japanese-mdmf(8)  

voipPotsLineConfTable 1.1.890.1.5.13.5.8.12.8
per-interface table for pots configuration
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipPotsLineConfEntry

voipPotsLineConfEntry 1.1.890.1.5.13.5.8.12.8.1
An entry in voipPotsLineConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipPotsLineConfEntry  

voipPotsLineFlashDefault 1.1.890.1.5.13.5.8.12.8.1.1
set positive non-zero value to configure default flash timer settings
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipPotsLineFlashMax 1.1.890.1.5.13.5.8.12.8.1.2
minimum flash period in ms
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 20..1500  

voipPotsLineFlashMin 1.1.890.1.5.13.5.8.12.8.1.3
maximum flash period in ms
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipPotsLineLoop 1.1.890.1.5.13.5.8.12.8.1.4
maximum loop resistance value
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ohm-2600(0), ohm-3200(1)  

enetLineConfTable 1.1.890.1.5.13.5.8.13.1
The table contains ethernet line configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnetLineConfEntry

enetLineConfEntry 1.1.890.1.5.13.5.8.13.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  EnetLineConfEntry  

enetLineConfBandWidthIngress 1.1.890.1.5.13.5.8.13.1.1.1
0~99968Kbps in step of 64Kbps, 0 means no limit.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

enetLineConfBandWidthEgress 1.1.890.1.5.13.5.8.13.1.1.2
0~99968Kbps in step of 64Kbps, 0 means no limit.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

enetLineConfFlowCtrlEnable 1.1.890.1.5.13.5.8.13.1.1.3
Enable/disable flow control.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

enetLineConfSpeed 1.1.890.1.5.13.5.8.13.1.1.4
Port spd/dplx configuration.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER auto(1), i100baseFD(2), i1000baseFD(3)  

enetPortConfTable 1.1.890.1.5.13.5.8.13.2
The table contains ethernet line configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnetPortConfEntry

enetPortConfEntry 1.1.890.1.5.13.5.8.13.2.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  EnetPortConfEntry  

enetPortConfPriority 1.1.890.1.5.13.5.8.13.2.1.1
The default ingress User Priority for this port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

enetPortConfPvid 1.1.890.1.5.13.5.8.13.2.1.2
The PVID, the VLAN ID assigned to untagged frames or Priority-Tagged frames received on this port.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

enetPortConfAcceptableFrameType 1.1.890.1.5.13.5.8.13.2.1.3
When this is admitOnlyVlanTagged(2) the device will discard untagged frames or Priority-Tagged frames received on this port. When admitAll(1), untagged frames or Priority-Tagged frames received on this port will be accepted and assigned to the PVID for this port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER admitAll(1), admitOnlyVlanTagged(2)  

enetPortConfTlsEnable 1.1.890.1.5.13.5.8.13.2.1.4
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

enetPortConfTlsVid 1.1.890.1.5.13.5.8.13.2.1.5
The transparent LAN VID.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

enetPortConfTlsPriority 1.1.890.1.5.13.5.8.13.2.1.6
The transparent LAN priority.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

enetPortConfRateLimitProfile 1.1.890.1.5.13.5.8.13.2.1.7
Rate Limit Profile name. This object is supported by R5.02 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

enetPortConfQueueRateLimitProfile 1.1.890.1.5.13.5.8.13.2.1.8
Set queue rate limit profile.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

enetPortConfDtEnable 1.1.890.1.5.13.5.8.13.2.1.9
Enable/disable double tag service on the specified subscriber port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

enetPortConfDtSvid 1.1.890.1.5.13.5.8.13.2.1.10
The service provider VLAN ID.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

enetPortConfDtSpriority 1.1.890.1.5.13.5.8.13.2.1.11
The service VLAN priority.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

enetPortConfDtCvid 1.1.890.1.5.13.5.8.13.2.1.12
The system-side customer VID.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

enetPortVlanTable 1.1.890.1.5.13.5.8.13.3
The table contains ethernet line vlan configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnetPortVlanEntry

enetPortVlanEntry 1.1.890.1.5.13.5.8.13.3.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  EnetPortVlanEntry  

enetPortVlanReg 1.1.890.1.5.13.5.8.13.3.1.1
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER egress(1), forbidden(2)  

enetPortVlanTag 1.1.890.1.5.13.5.8.13.3.1.2
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER tag(1), untag(2)  

enetPortVlanRowStatus 1.1.890.1.5.13.5.8.13.3.1.3
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

elcDot3ad 1.1.890.1.5.13.5.8.13.4
OBJECT IDENTIFIER    

elcDot3adTable 1.1.890.1.5.13.5.8.13.4.1
The table contains dot3ad configuration. This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ElcDot3adEntry

elcDot3adEntry 1.1.890.1.5.13.5.8.13.4.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  ElcDot3adEntry  

elcDot3adSlotId 1.1.890.1.5.13.5.8.13.4.1.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

elcDot3adGroupId 1.1.890.1.5.13.5.8.13.4.1.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..10  

elcDot3adEnable 1.1.890.1.5.13.5.8.13.4.1.1.3
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), enableWithLacp(2), disable(3)  

elcAggPortTable 1.1.890.1.5.13.5.8.13.4.2
The table contains port aggregation configuration. This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ElcAggPortEntry

elcAggPortEntry 1.1.890.1.5.13.5.8.13.4.2.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  ElcAggPortEntry  

elcAggPortJoin 1.1.890.1.5.13.5.8.13.4.2.1.1
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disjoin(0), joinTrunkingGroup1(1), joinTrunkingGroup2(2), joinTrunkingGroup3(3), joinTrunkingGroup4(4), joinTrunkingGroup5(5), joinTrunkingGroup6(6), joinTrunkingGroup7(7), joinTrunkingGroup8(8), joinTrunkingGroup9(9), joinTrunkingGroup10(10)  

enetQoS 1.1.890.1.5.13.5.8.13.5
OBJECT IDENTIFIER    

enetQScheduleTable 1.1.890.1.5.13.5.8.13.5.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnetQScheduleEntry

enetQScheduleEntry 1.1.890.1.5.13.5.8.13.5.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  EnetQScheduleEntry  

enetQScheduleType 1.1.890.1.5.13.5.8.13.5.1.1.1
Queue scheduling type (strictly priority queue or weighted round robin).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

enetQueueWeightTable 1.1.890.1.5.13.5.8.13.5.2
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnetQueueWeightEntry

enetQueueWeightEntry 1.1.890.1.5.13.5.8.13.5.2.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  EnetQueueWeightEntry  

enetQueueWeight 1.1.890.1.5.13.5.8.13.5.2.1.1
Weight for the priority queue, 0 means strict priority
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

enetPortPvlanTable 1.1.890.1.5.13.5.8.13.6
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnetPortPvlanEntry

enetPortPvlanEntry 1.1.890.1.5.13.5.8.13.6.1
An entry in enetPortPvlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  EnetPortPvlanEntry  

enetPortPvlanEtype 1.1.890.1.5.13.5.8.13.6.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

enetPortPvlanVid 1.1.890.1.5.13.5.8.13.6.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

enetPortPvlanPriority 1.1.890.1.5.13.5.8.13.6.1.3
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

enetPortPvlanRowStatus 1.1.890.1.5.13.5.8.13.6.1.4
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

enetPortXvlanTable 1.1.890.1.5.13.5.8.13.7
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnetPortXvlanEntry

enetPortXvlanEntry 1.1.890.1.5.13.5.8.13.7.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  EnetPortXvlanEntry  

enetPortXvlanCvid 1.1.890.1.5.13.5.8.13.7.1.1
the original vlan id in the 8021q tag, 1~4094
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4094  

enetPortXvlanSvid 1.1.890.1.5.13.5.8.13.7.1.2
the result vlan id in the 8021q tag, or in the QinQ S-tag, 1~4094
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4094  

enetPortXvlanRowStatus 1.1.890.1.5.13.5.8.13.7.1.3
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

gbondGroupTable 1.1.890.1.5.13.5.8.14
The table contains bonding group configuration. This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GbondGroupEntry

gbondGroupEntry 1.1.890.1.5.13.5.8.14.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  GbondGroupEntry  

gbondGroupName 1.1.890.1.5.13.5.8.14.1.1
An administratively assigned string, which may be used to identify bonding group.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

gbondGroupPorts 1.1.890.1.5.13.5.8.14.1.2
The set of ports which are currently assigned to the bonding group of specified group name. Each bit in the octet specifies a port from MSB to LSB. For example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING  

gbondGroupRowStatus 1.1.890.1.5.13.5.8.14.1.3
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

dtpvcTable 1.1.890.1.5.13.5.8.15.1
This table includes Double Tagging PVC configuration. This table is supported by R5.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DtpvcEntry

dtpvcEntry 1.1.890.1.5.13.5.8.15.1.1
An entry of dtpvcTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DtpvcEntry  

dtpvcVpi 1.1.890.1.5.13.5.8.15.1.1.1
VPI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

dtpvcVci 1.1.890.1.5.13.5.8.15.1.1.2
VCI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

dtpvcSvid 1.1.890.1.5.13.5.8.15.1.1.3
s-tag of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

dtpvcCvid 1.1.890.1.5.13.5.8.15.1.1.4
c-tag of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

dtpvcEncap 1.1.890.1.5.13.5.8.15.1.1.5
Encapsulation of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER llc(1), vc(2)  

dtpvcSPriority 1.1.890.1.5.13.5.8.15.1.1.6
s-priority of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

dtpvcCPriority 1.1.890.1.5.13.5.8.15.1.1.7
c-priority of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

dtpvcProfile 1.1.890.1.5.13.5.8.15.1.1.8
The value of this object identifies the row in the atmProfileTable, which applies for this pvc.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

dtpvcRowStatus 1.1.890.1.5.13.5.8.15.1.1.9
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

dtpvcMvlanEnable 1.1.890.1.5.13.5.8.15.1.1.10
Enable/disable multicast VLAN function for the DTPVC.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

e1PortConfTable 1.1.890.1.5.13.5.8.16.1
This table is supported by R5.03 and later versions. The table contains E1 line configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    E1PortConfEntry

e1PortConfEntry 1.1.890.1.5.13.5.8.16.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  E1PortConfEntry  

e1PortConfAdminStatus 1.1.890.1.5.13.5.8.16.1.1.1
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

e1PortConfAlarmProfile 1.1.890.1.5.13.5.8.16.1.1.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

e1PortConfImpedance 1.1.890.1.5.13.5.8.16.1.1.3
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER impedance-75ohm(1), impedance-120ohm(2)  

e1PortConfTimingSrc 1.1.890.1.5.13.5.8.16.1.1.4
0: local, 1~8 E1 port: the timing source port id
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

xvlanTable 1.1.890.1.5.13.5.8.17.1
This table is supported by R5.04 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    XvlanEntry

xvlanEntry 1.1.890.1.5.13.5.8.17.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  XvlanEntry  

xvlanCvid 1.1.890.1.5.13.5.8.17.1.1.1
the original vlan id in the 8021q tag, 1~4094
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4094  

xvlanSvid 1.1.890.1.5.13.5.8.17.1.1.2
the result vlan id in the 8021q tag, or in the QinQ S-tag, 1~4094
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4094  

xvlanCvids 1.1.890.1.5.13.5.8.17.1.1.3
the result vlan id in the QinQ C-tag, 0~4094, 0 means single tag
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..4094  

xvlanRowStatus 1.1.890.1.5.13.5.8.17.1.1.4
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

vdsl2LineConfTable 1.1.890.1.5.13.5.8.18.1
This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Vdsl2LineConfEntry

vdsl2LineConfEntry 1.1.890.1.5.13.5.8.18.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  Vdsl2LineConfEntry  

vdsl2LineConfRateLimitProfile 1.1.890.1.5.13.5.8.18.1.1.1
Set rate limit profile
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

vdsl2LineConfQueueRateLimitProfile 1.1.890.1.5.13.5.8.18.1.1.2
Set queue rate limit profile
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

vdsl2Pvc 1.1.890.1.5.13.5.8.18.2
OBJECT IDENTIFIER    

vdsl2PvcTable 1.1.890.1.5.13.5.8.18.2.1
This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Vdsl2PvcEntry

vdsl2PvcEntry 1.1.890.1.5.13.5.8.18.2.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  Vdsl2PvcEntry  

vdsl2PvcVpi 1.1.890.1.5.13.5.8.18.2.1.1.1
VPI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

vdsl2PvcVci 1.1.890.1.5.13.5.8.18.2.1.1.2
VCI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

vdsl2PvcPvid 1.1.890.1.5.13.5.8.18.2.1.1.3
Default VID of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4094  

vdsl2PvcEncap 1.1.890.1.5.13.5.8.18.2.1.1.4
Encapsulation of the pvc.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER llc(1), vc(2)  

vdsl2PvcPriority 1.1.890.1.5.13.5.8.18.2.1.1.5
802.1p default priority of the pvc.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

vdsl2PvcSuper 1.1.890.1.5.13.5.8.18.2.1.1.6
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

vdsl2PvcRowStatus 1.1.890.1.5.13.5.8.18.2.1.1.7
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

vdsl2QSchedule 1.1.890.1.5.13.5.8.18.3
OBJECT IDENTIFIER    

vdsl2QScheduleTable 1.1.890.1.5.13.5.8.18.3.1
The table contains queue schedule configuration for the vdsl2 ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Vdsl2QSchedulePortEntry

vdsl2QScheduleEntry 1.1.890.1.5.13.5.8.18.3.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  Vdsl2QSchedulePortEntry  

vdsl2QScheduleType 1.1.890.1.5.13.5.8.18.3.1.1.1
Queue scheduling type (strictly priority queue or weighted round robin).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER spq(1), wrr(2)  

vdsl2QueueWeightTable 1.1.890.1.5.13.5.8.18.3.2
The table contains weight configuration for the priority queues.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Vdsl2QueueWeightEntry

vdsl2QueueWeightEntry 1.1.890.1.5.13.5.8.18.3.2.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  Vdsl2QueueWeightEntry  

vdsl2QueueWeight 1.1.890.1.5.13.5.8.18.3.2.1.1
Weight for the priority queue, 0 means strict priority
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..15  

pvcAll 1.1.890.1.5.13.5.8.19
OBJECT IDENTIFIER    

pvcAllFilter 1.1.890.1.5.13.5.8.19.1
Ifindex to filter pvc, value 0 indicates to display all.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

pvcAllTable 1.1.890.1.5.13.5.8.19.2
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PvcAllEntry

pvcAllEntry 1.1.890.1.5.13.5.8.19.2.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  PvcAllEntry  

pvcAllVpi 1.1.890.1.5.13.5.8.19.2.1.1
VPI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

pvcAllVci 1.1.890.1.5.13.5.8.19.2.1.2
VCI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

pvcAllEncap 1.1.890.1.5.13.5.8.19.2.1.3
Encapsulation of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER llc(1), vc(2)  

pvcAllType 1.1.890.1.5.13.5.8.19.2.1.4
Type of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER pvc(1), paepvc(2), tlspvc(3), ipbpvc(4), dtpvc(5)  

vdsl2Paepvc 1.1.890.1.5.13.5.8.18.4
OBJECT IDENTIFIER    

vdsl2PaepvcTable 1.1.890.1.5.13.5.8.18.4.1
This table includes PPPoAoE PVC configuration. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Vdsl2PaepvcEntry

vdsl2PaepvcEntry 1.1.890.1.5.13.5.8.18.4.1.1
An entry of vdsl2PaepvcTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Vdsl2PaepvcEntry  

vdsl2PaepvcVpi 1.1.890.1.5.13.5.8.18.4.1.1.1
VPI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

vdsl2PaepvcVci 1.1.890.1.5.13.5.8.18.4.1.1.2
VCI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

vdsl2PaepvcPvid 1.1.890.1.5.13.5.8.18.4.1.1.3
Default VID of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

vdsl2PaepvcEncap 1.1.890.1.5.13.5.8.18.4.1.1.4
Encapsulation of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER llc(1), vc(2)  

vdsl2PaepvcPriority 1.1.890.1.5.13.5.8.18.4.1.1.5
802.1p default priority of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

vdsl2PaepvcAcName 1.1.890.1.5.13.5.8.18.4.1.1.6
Access concentrator name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

vdsl2PaepvcServiceName 1.1.890.1.5.13.5.8.18.4.1.1.7
Service name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

vdsl2PaepvcHelloTime 1.1.890.1.5.13.5.8.18.4.1.1.8
The system will close the PVC if there are not any LCP echo messages passed through during the LCP hello time.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

vdsl2PaepvcRowStatus 1.1.890.1.5.13.5.8.18.4.1.1.9
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

adslProfile 1.1.890.1.5.13.5.9.1
OBJECT IDENTIFIER    

shdslProfile 1.1.890.1.5.13.5.9.2
OBJECT IDENTIFIER    

atmProfile 1.1.890.1.5.13.5.9.3
OBJECT IDENTIFIER    

profsvr 1.1.890.1.5.13.5.9.4
OBJECT IDENTIFIER    

aclProfile 1.1.890.1.5.13.5.9.5
OBJECT IDENTIFIER    

vdslProfile 1.1.890.1.5.13.5.9.6
OBJECT IDENTIFIER    

voipProfile 1.1.890.1.5.13.5.9.7
OBJECT IDENTIFIER    

ipqosProfile 1.1.890.1.5.13.5.9.8
OBJECT IDENTIFIER    

rateLimitProfile 1.1.890.1.5.13.5.9.9
OBJECT IDENTIFIER    

e1AlarmProfile 1.1.890.1.5.13.5.9.10
OBJECT IDENTIFIER    

vdsl2Profile 1.1.890.1.5.13.5.9.11
OBJECT IDENTIFIER    

queueRateLimitProfile 1.1.890.1.5.13.5.9.12
OBJECT IDENTIFIER    

ipqos2Profile 1.1.890.1.5.13.5.9.13
OBJECT IDENTIFIER    

maxNumOfAdslLineProfiles 1.1.890.1.5.13.5.9.1.1
The maximum number of ADSL line profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

maxNumOfAdslAlarmProfiles 1.1.890.1.5.13.5.9.1.2
The maximum number of ADSL alarm profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

maxNumOfShdslLineProfiles 1.1.890.1.5.13.5.9.2.1
The maximum number of SHDSL line profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

maxNumOfShdslAlarmProfiles 1.1.890.1.5.13.5.9.2.2
The maximum number of SHDSL alarm profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

maxNumOfAtmProfiles 1.1.890.1.5.13.5.9.3.1
The maximum number of ATM profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

atmProfileTable 1.1.890.1.5.13.5.9.3.2
This table contains information on the PVC configuration. One entry in this table reflects a profile which can be used to configure the PVC.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AtmProfileEntry

atmProfileEntry 1.1.890.1.5.13.5.9.3.2.1
An entry in atmProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AtmProfileEntry  

atmProfileName 1.1.890.1.5.13.5.9.3.2.1.1
This object is used by the ATM profile table in order to identify a row of this table.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

atmProfileAAL 1.1.890.1.5.13.5.9.3.2.1.2
ATM Adaptation Layer policy.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..5  

atmProfileClass 1.1.890.1.5.13.5.9.3.2.1.3
ATM traffic class, including constant bit rate, real-time variable bit rate, non real-time variable bit rate, unspecified bit rate, and available bit rate.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER cbr(1), rt-vbr(2), nrt-vbr(3), ubr(4), abr(5)  

atmProfilePcr 1.1.890.1.5.13.5.9.3.2.1.4
Peak Cell Rate.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

atmProfileCdvt 1.1.890.1.5.13.5.9.3.2.1.5
Cell Delay Variation Tolerance.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..255  

atmProfileScrMcr 1.1.890.1.5.13.5.9.3.2.1.6
Sustain Cell Rate for vbr or Minimum Cell Rate for abr.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

atmProfileBt 1.1.890.1.5.13.5.9.3.2.1.7
Burst Tolerance for vbr.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..255  

atmProfileRowStatus 1.1.890.1.5.13.5.9.3.2.1.8
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

profileServerMode 1.1.890.1.5.13.5.9.4.1
The object indicates the system is running profile server with server mode or client mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER server(1), client(2)  

profileServerIp 1.1.890.1.5.13.5.9.4.2
IP address of the profile server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

profsvrClientTable 1.1.890.1.5.13.5.9.4.3
This table includes the clients to be provisioned.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ProfsvrClientEntry

profsvrClientEntry 1.1.890.1.5.13.5.9.4.3.1
An entry of profsvrClientTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ProfsvrClientEntry  

profsvrClientIp 1.1.890.1.5.13.5.9.4.3.1.1
IP address of the client to be provisioned.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

profsvrClientType 1.1.890.1.5.13.5.9.4.3.1.2
Provision type to decide whether deleting unmapped profiles in client or not.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER nodelete(1), delete(2)  

profsvrClientRowStatus 1.1.890.1.5.13.5.9.4.3.1.3
The row status is used to create or delete a client.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

profileServerSync 1.1.890.1.5.13.5.9.4.4
The manager sets the object to be one to start profile synchronization. The agent should clear the object to be zero when the operation is completed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

aclProfileTable 1.1.890.1.5.13.5.9.5.1
This table is supported by R1.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AclProfileEntry

aclProfileEntry 1.1.890.1.5.13.5.9.5.1.1
An entry of aclProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AclProfileEntry  

aclProfileRuleName 1.1.890.1.5.13.5.9.5.1.1.1
Profile rule name
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

aclProfileRuleNumber 1.1.890.1.5.13.5.9.5.1.1.2
The managed object is for acl profile rule configuration. etype vlan (1), etype smac (2), etype dmac (3), vlan smac (4), vlan dmac (5), smac dmac (6), vlan priority (7), etype (8), vlan (9), smac (10), dmac (11), priority (12), protocol (13), {srcip /{|dstip /{|tos {|srcport {|dstport }}}}} (14), vlan sip (15), vlan dip (16), vlan sport tcp|udp (17), vlan dport tcp|udp (18), vlan smac sip (19), vlan dmac dip (20), srcip /|dstip |tos |srcport |dstport (21), vlan sip (22), vlan dip (23)
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

aclProfileActionNumber 1.1.890.1.5.13.5.9.5.1.1.3
Profile action number. Bit 1: rate Bit 2: rvlan Bit 3: rpri Bit 4: deny Bit 1, Bit 2 & Bit 3 can multiple selection.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

aclProfileRuleParamMask 1.1.890.1.5.13.5.9.5.1.1.4
Profile rule parameter mask. BIT 1: srcip / BIT 2: dstip / BIT 3: tos BIT 4: srcport BIT 5: dstport
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

aclProfileRuleEtype 1.1.890.1.5.13.5.9.5.1.1.5
Profile rule etype.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..65535  

aclProfileRuleVid 1.1.890.1.5.13.5.9.5.1.1.6
Profile rule vid.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..4094  

aclProfileRuleSmac 1.1.890.1.5.13.5.9.5.1.1.7
Profile rule source MAC.
Status: current Access: read-create
OBJECT-TYPE    
  PhysAddress  

aclProfileRuleDmac 1.1.890.1.5.13.5.9.5.1.1.8
Profile rule destination MAC.
Status: current Access: read-create
OBJECT-TYPE    
  PhysAddress  

aclProfileRulePriority 1.1.890.1.5.13.5.9.5.1.1.9
Profile rule priority.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

aclProfileRuleProtocol 1.1.890.1.5.13.5.9.5.1.1.10
Profile rule protocol. icmp(1),igmp(2),ip(4),tcp(6),udp(17),gre(47),ospf(89), and other protocol types.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..65535  

aclProfileRuleSrcIP 1.1.890.1.5.13.5.9.5.1.1.11
Profile rule source IP
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

aclProfileRuleSrcIPMask 1.1.890.1.5.13.5.9.5.1.1.12
The subnet mask of source IP mask.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..32  

aclProfileRuleDestIP 1.1.890.1.5.13.5.9.5.1.1.13
Profile rule source IP.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

aclProfileRuleDestIPMask 1.1.890.1.5.13.5.9.5.1.1.14
The subnet mask of destination IP mask.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..32  

aclProfileRuleStartTos 1.1.890.1.5.13.5.9.5.1.1.15
Profile rule start type of service.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..255  

aclProfileRuleEndTos 1.1.890.1.5.13.5.9.5.1.1.16
Profile rule end type of service.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..255  

aclProfileRuleSrcStartPort 1.1.890.1.5.13.5.9.5.1.1.17
Profile rule source start port.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..65535  

aclProfileRuleSrcEndPort 1.1.890.1.5.13.5.9.5.1.1.18
Profile rule source end port.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..65535  

aclProfileRuleDestStartPort 1.1.890.1.5.13.5.9.5.1.1.19
Profile rule destination start port.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..65535  

aclProfileRuleDestEndPort 1.1.890.1.5.13.5.9.5.1.1.20
Profile rule destination end port.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..65535  

aclProfileActionRate 1.1.890.1.5.13.5.9.5.1.1.21
Profile action to replace to this rate.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..100032  

aclProfileActionrvlan 1.1.890.1.5.13.5.9.5.1.1.22
Profile action to replace to this vlan.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..4094  

aclProfileActionrpri 1.1.890.1.5.13.5.9.5.1.1.23
Profile action to replace to this priority.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

aclProfileRowStatus 1.1.890.1.5.13.5.9.5.1.1.24
The row status of the entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

aclProfileRuleSip 1.1.890.1.5.13.5.9.5.1.1.25
Source IP.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

aclProfileRuleDip 1.1.890.1.5.13.5.9.5.1.1.26
Destination IP.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

aclProfileRuleSport 1.1.890.1.5.13.5.9.5.1.1.27
Source port.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..65535  

aclProfileRuleDport 1.1.890.1.5.13.5.9.5.1.1.28
Destination port.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..65535  

aclProfileRuleSrcIp6 1.1.890.1.5.13.5.9.5.1.1.29
srcip for RuleNumber (21).
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

aclProfileRuleDstIp6 1.1.890.1.5.13.5.9.5.1.1.30
dstip for RuleNumber (21).
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

aclProfileRuleSip6 1.1.890.1.5.13.5.9.5.1.1.31
sip for RuleNumber (19), (22).
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

aclProfileRuleDip6 1.1.890.1.5.13.5.9.5.1.1.32
dip for RuleNumber (20), (23).
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress  

maxNumOfVdslLineProfiles 1.1.890.1.5.13.5.9.6.1
The maximum number of VDSL line profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

maxNumOfVdslAlarmProfiles 1.1.890.1.5.13.5.9.6.2
The maximum number of VDSL alarm profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineConfProfileExtendedTable 1.1.890.1.5.13.5.9.6.3
This table contains information on the VDSL line profile extension configuration. This table is supported by R5.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineConfProfileExtendedEntry

vdslLineConfProfileExtendedEntry 1.1.890.1.5.13.5.9.6.3.1
An entry in vdslLineConfProfileExtendedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineConfProfileExtendedEntry  

vdsl2LConfProfRaModeDs 1.1.890.1.5.13.5.9.6.3.1.1
(RA-MODEds). The mode of operation of a rate-adaptive xTU-C in the transmit direction. The parameter can take three values: manual(1), raInit(2), dynamicRa(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER manual(1), raInit(2), dynamicRa(3)  

vdsl2LConfProfRaModeUs 1.1.890.1.5.13.5.9.6.3.1.2
(RA-MODEus). The mode of operation of a rate-adaptive xTU-R in the transmit direction. The parameter can take three values: manual(1), raInit(2), dynamicRa(3).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER manual(1), raInit(2), dynamicRa(3)  

vdsl2LConfProfRaUsNrmDs 1.1.890.1.5.13.5.9.6.3.1.3
(RA-USNRMds). The Downstream Up-Shift Noise Margin value, to be used when xdsl2LConfProfRaModeDs is set to dynamicRa. If the downstream noise margin is above this value and stays above it for more than the time specified by the xdsl2LConfProfRaUsTimeDs, the xTU-R shall attempt to increase the downstream net data rate. The Downstream Up-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB).
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..310  

vdsl2LConfProfRaUsNrmUs 1.1.890.1.5.13.5.9.6.3.1.4
(RA-USNRMus). The Upstream Up-Shift Noise Margin value, to be used when xdsl2LConfProfRaModeUs is set to dynamicRa. If the upstream noise margin is above this value and stays above it for more than the time specified by the xdsl2LConfProfRaUsTimeUs, the xTU-C shall attempt to increase the upstream net data rate. The Upstream Up-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB).
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..310  

vdsl2LConfProfRaDsNrmDs 1.1.890.1.5.13.5.9.6.3.1.5
(RA-DSNRMds). The Downstream Down-Shift Noise Margin value, to be used when xdsl2LConfProfRaModeDs is set to dynamicRa. If the downstream noise margin is below this value and stays below that for more than the time specified by the xdsl2LConfProfRaDsTimeDs, the xTU-R shall attempt to decrease the downstream net data rate. The Downstream Down-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB).
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..310  

vdsl2LConfProfRaDsNrmUs 1.1.890.1.5.13.5.9.6.3.1.6
(RA-DSNRMus). The Upstream Downshift Noise Margin value, to be used when xdsl2LConfProfRaModeUs is set to dynamicRa. If the upstream noise margin is below this value and stays below that for more than the time specified by the xdsl2LConfProfRaDsTimeUs, the xTU-C shall attempt to decrease the upstream net data rate. The Upstream Down-shift Noise Margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB).
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..310  

vdsl2LConfProfProfileName 1.1.890.1.5.13.5.9.6.3.1.7
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

vdslLineAlarmConfProfileExtendedTable 1.1.890.1.5.13.5.9.6.4
This table contains information on the VDSL line alarm profile extension configuration. This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineAlarmConfProfileExtendedEntry

vdslLineAlarmConfProfileExtendedEntry 1.1.890.1.5.13.5.9.6.4.1
An entry in vdslLineAlarmConfProfileExtendedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineAlarmConfProfileExtendedEntry  

vdslLAlarmConfProfProfileName 1.1.890.1.5.13.5.9.6.4.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

sipProfile 1.1.890.1.5.13.5.9.7.1
OBJECT IDENTIFIER    

h248Profile 1.1.890.1.5.13.5.9.7.4
OBJECT IDENTIFIER    

maxNumOfSipProfiles 1.1.890.1.5.13.5.9.7.1.1
The maximum number of SIP profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sipProfileTable 1.1.890.1.5.13.5.9.7.1.2
This table includes SIP protocol related configuration. This table is supported by R4.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SipProfileEntry

sipProfileEntry 1.1.890.1.5.13.5.9.7.1.2.1
An entry in sipProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SipProfileEntry  

sipProfileName 1.1.890.1.5.13.5.9.7.1.2.1.1
This object is used by the SIP profile table in order to identify a row of this table.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

sipProfileSipSvr 1.1.890.1.5.13.5.9.7.1.2.1.2
IP used for SIP registration or SIP domain name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

sipProfileRegSvr 1.1.890.1.5.13.5.9.7.1.2.1.3
Registration server IP or registration server domain name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

sipProfileProxySvr 1.1.890.1.5.13.5.9.7.1.2.1.4
Proxy server IP or proxy server doamin name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

sipProfileSipPort 1.1.890.1.5.13.5.9.7.1.2.1.5
SIP UA port number.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1025..65535  

sipProfileRegSvrPort 1.1.890.1.5.13.5.9.7.1.2.1.6
Registration server port number.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1025..65535  

sipProfileProxySvrPort 1.1.890.1.5.13.5.9.7.1.2.1.7
Proxy server port number.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1025..65535  

sipProfileUriType 1.1.890.1.5.13.5.9.7.1.2.1.8
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER use-sip-uri(1), use-tel-uri(2)  

sipProfilePbit 1.1.890.1.5.13.5.9.7.1.2.1.9
802.1p bit for SIP and RTP packet.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

sipProfileDscp 1.1.890.1.5.13.5.9.7.1.2.1.10
DSCP for SIP and RTP packet.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..63  

sipProfileKeepAlive 1.1.890.1.5.13.5.9.7.1.2.1.11
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

sipProfileSe 1.1.890.1.5.13.5.9.7.1.2.1.12
Session expiration time in seconds.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 90..65535  

sipProfilePrack 1.1.890.1.5.13.5.9.7.1.2.1.13
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

sipProfileRowStatus 1.1.890.1.5.13.5.9.7.1.2.1.14
This object is used to create a new row or delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sipProfileReSend 1.1.890.1.5.13.5.9.7.1.2.1.15
resend factor of session expiration time. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

sipProfileNonceCountKeep 1.1.890.1.5.13.5.9.7.1.2.1.16
This MIB object is supported by R5.05 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

sipProfileQopQuote 1.1.890.1.5.13.5.9.7.1.2.1.17
This MIB object is supported by R5.05 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

sipProfileRefertobracket 1.1.890.1.5.13.5.9.7.1.2.1.18
This MIB object is supported by R5.05 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

sipProfileRefertodot 1.1.890.1.5.13.5.9.7.1.2.1.19
This MIB object is supported by R5.05 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER dot(1), hex(2)  

sipProfileRtpStartPort 1.1.890.1.5.13.5.9.7.1.2.1.20
start of RTP port number. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

sipProfileRtpEndPort 1.1.890.1.5.13.5.9.7.1.2.1.21
end of RTP port number. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

maxNumOfSipCallSvcProfiles 1.1.890.1.5.13.5.9.7.1.3
The maximum number of SIP call service profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sipCallSvcProfileTable 1.1.890.1.5.13.5.9.7.1.4
This table includes SIP call service related configuration. This table is supported by R4.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SipCallSvcProfileEntry

sipCallSvcProfileEntry 1.1.890.1.5.13.5.9.7.1.4.1
An entry in sipCallSvcProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SipCallSvcProfileEntry  

sipCallSvcProfileName 1.1.890.1.5.13.5.9.7.1.4.1.1
This object is used by the SIP call service profile table in order to identify a row of this table.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

sipCallSvcProfilePasswdOn 1.1.890.1.5.13.5.9.7.1.4.1.2
Password is necessary or not for SIP registration.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

sipCallSvcProfilePasswd 1.1.890.1.5.13.5.9.7.1.4.1.3
SIP registration password.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

sipCallSvcProfileNumberPlanOn 1.1.890.1.5.13.5.9.7.1.4.1.4
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

sipCallSvcProfileNumberPlanCc 1.1.890.1.5.13.5.9.7.1.4.1.5
Country code, only digit 0..9 are allowed.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..7)  

sipCallSvcProfileNumberPlanNdc 1.1.890.1.5.13.5.9.7.1.4.1.6
National destination code, only digit 0..9 are allowed.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..7)  

sipCallSvcProfileNumberPlanTable 1.1.890.1.5.13.5.9.7.1.4.1.7
Numbering plan table name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

sipCallSvcProfileStateMask 1.1.890.1.5.13.5.9.7.1.4.1.8
Bit 1 reserved : reserved Bit 2 callhold : call hold Bit 3 callwait : call waiting Bit 4 callreturn : call return Bit 5 calltransfer : call transfer Bit 6 clip : caller line identification presentation (Caller ID) Bit 7 clir : caller line identification restriction Bit 8 dnd : do not disturb Bit 9 registration Bit 10 localcall Bit 11 mwi : message waiting indicator Bit 12 cidcw : caller identity with call waiting Bit 13 conference Bit 14 callsvcmode : europe(0) usa(1) Bit 15 on hook transfer Bit 16 conference transfer
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

sipCallSvcProfileDtmf 1.1.890.1.5.13.5.9.7.1.4.1.9
dtmf bypass : bypass DTMF tone dtmf rfc2833 : DTMF tone relay according to RFC2833 dtmf rfc2833like : DTMF tone relay by SIP INFO message, but RFC2833 payload dtmf sipinfo : DTMF tone relay by SIP INFO signal message dtmf plaintext : DTMF tone relay by SIP INFO plain text message
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER bypass(1), rfc2833(2), rfc2833like(3), sipinfo(4), plaintext(5)  

sipCallSvcProfileFax 1.1.890.1.5.13.5.9.7.1.4.1.10
fax g711 : FAX service pass through by ITU-T G.711 fax t38 : FAX service by ITU-T T.38 UDP fax t38rtp : FAX service by ITU-T T.38 RTP
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER g711(1), t38(2), t38rtp(3)  

sipCallSvcProfileRowStatus 1.1.890.1.5.13.5.9.7.1.4.1.11
This object is used to create a new row or delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

sipCallSvcProfileKeypattern 1.1.890.1.5.13.5.9.7.1.4.1.12
Key pattern table name. This object is supported by R5.01 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

sipCallSvcProfileRegTime 1.1.890.1.5.13.5.9.7.1.4.1.13
Registration expiration time in seconds.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 120..65535  

sipCallSvcProfileFlash 1.1.890.1.5.13.5.9.7.1.4.1.14
flash invite : send SIP INVITE message flash rfc2833 : flash relay according to RFC2833 flash rfc2833like : flash relay by SIP INFO message, but RFC2833 payload flash sipinfo1 : flash relay by SIP INFO signal=16 message flash sipinfo2 : flash relay by SIP INFO signal=hf message flash sipinfo3 : flash relay by SIP INFO signal=hook-flash message flash sipinfo4 : flash relay by SIP INFO plain text message flash sipinfo5 : flash relay by multiple SIP INFO signal messages and signal content come from specified pattern string flash sipinfo6 : flash relay by SIP INFO specified information message
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER invite(1), rfc2833(2), rfc2833like(3), sipinfo1(4), sipinfo2(5), sipinfo3(6), sipinfo4(7), sipinfo5(8), sipinfo6(9)  

sipCallSvcProfileFlashPattern 1.1.890.1.5.13.5.9.7.1.4.1.15
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

sipCallSvcProfileReanswerTime 1.1.890.1.5.13.5.9.7.1.4.1.16
Reanswer time. The time period after user hangs up and before call is disconnected.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

sipCallSvcProfileFirstDigit 1.1.890.1.5.13.5.9.7.1.4.1.17
first digit timeout. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

sipCallSvcProfileInterdigit 1.1.890.1.5.13.5.9.7.1.4.1.18
inter digit timeout. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

sipCallSvcProfileLocalHelpTable 1.1.890.1.5.13.5.9.7.1.5
This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SipCallSvcProfileLocalHelpEntry

sipCallSvcProfileLocalHelpEntry 1.1.890.1.5.13.5.9.7.1.5.1
An entry in sipCallSvcProfileLocalHelpTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SipCallSvcProfileLocalHelpEntry  

sipCallSvcProfileLocalHelpIndex 1.1.890.1.5.13.5.9.7.1.5.1.1
Index number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

sipCallSvcProfileLocalHelpTableName 1.1.890.1.5.13.5.9.7.1.5.1.2
Local help table name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

sipCallSvcProfileLocalHelpTableTel 1.1.890.1.5.13.5.9.7.1.5.1.3
Local help telephone number. Only digit characters are allowed. Note that sipCallSvcProfileLocalHelpTableName and sipCallSvcProfileLocalHelpTableTel must be set sequentially.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..15)  

maxNumOfSipDialPlanProfiles 1.1.890.1.5.13.5.9.7.1.6
The maximum number of SIP dial plan profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sipDialPlanProfileTable 1.1.890.1.5.13.5.9.7.1.7
Configure dial plan related configuration of specified profile. This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SipDialPlanProfileEntry

sipDialPlanProfileEntry 1.1.890.1.5.13.5.9.7.1.7.1
An entry in sipDialPlanProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SipDialPlanProfileEntry  

sipDialPlanProfileName 1.1.890.1.5.13.5.9.7.1.7.1.1
Profile name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

sipDialPlanProfileIndex 1.1.890.1.5.13.5.9.7.1.7.1.2
Index number. 1-32 means dialplan pattern, 255 means default SIP server profile name
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

sipDialPlanProfileDialPlanTableName 1.1.890.1.5.13.5.9.7.1.7.1.3
Dial plan table name. 1-32 means dialplan pattern, 255 means default SIP server profile name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

sipDialPlanProfileRowStatus 1.1.890.1.5.13.5.9.7.1.7.1.4
This object is used to create a new row or delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

maxNumOfH248Profiles 1.1.890.1.5.13.5.9.7.4.1
The maximum number of H.248 profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

h248ProfileTable 1.1.890.1.5.13.5.9.7.4.2
This table includes H.248 protocol related configuration. This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    H248ProfileEntry

h248ProfileEntry 1.1.890.1.5.13.5.9.7.4.2.1
An entry in h248ProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  H248ProfileEntry  

h248ProfileName 1.1.890.1.5.13.5.9.7.4.2.1.1
This object is used by the H.248 profile table in order to identify a row of this table.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

h248ProfileMgc 1.1.890.1.5.13.5.9.7.4.2.1.2
MGC IP or domain name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..63)  

h248ProfileMgcPort 1.1.890.1.5.13.5.9.7.4.2.1.3
MGC port number.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1025..65535  

h248ProfileMgc2On 1.1.890.1.5.13.5.9.7.4.2.1.4
Secondary MGC on/off.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

h248ProfileMgc2 1.1.890.1.5.13.5.9.7.4.2.1.5
Secondary MGC IP or domain name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

h248ProfileMgc2Port 1.1.890.1.5.13.5.9.7.4.2.1.6
Secondary MGC port.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1025..65535  

h248ProfileTransport 1.1.890.1.5.13.5.9.7.4.2.1.7
Transport protocol.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER udp(1), tcp(2)  

h248ProfileEncode 1.1.890.1.5.13.5.9.7.4.2.1.8
H.248 coding type.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER long(1), short(2)  

h248ProfilePbit 1.1.890.1.5.13.5.9.7.4.2.1.9
802.1p bit for H.248 and RTP packet.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

h248ProfileDscp 1.1.890.1.5.13.5.9.7.4.2.1.10
DSCP for H.248 and RTP packet.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..63  

h248ProfileRowStatus 1.1.890.1.5.13.5.9.7.4.2.1.11
This object is used to create a new row or delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

h248ProfileSoftswitch 1.1.890.1.5.13.5.9.7.4.2.1.12
This MIB object is supported by R5.06 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER defval(1), zxss10-ss(2), nortel-cs1500(3), nortel-cs2000(4), huawei-soft3000(5), alu-5020(6), nsn(7), iskratel(8), alu-5060(9)  

h248ProfileInactivityTimer 1.1.890.1.5.13.5.9.7.4.2.1.13
This MIB object is supported by R5.06 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..65535  

h248ProfilePrefixName 1.1.890.1.5.13.5.9.7.4.2.1.14
ephemeral termination prefix, up to 31 characters. This MIB object is supported by R5.06 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

h248ProfileRtpPortStart 1.1.890.1.5.13.5.9.7.4.2.1.15
start port of RTP 4000 ~ 64000 This MIB object is supported by R5.06 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

h248ProfileRtpPortEnd 1.1.890.1.5.13.5.9.7.4.2.1.16
end port of RTP 5000 ~ 65000 This MIB object is supported by R5.06 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

h248ProfileInitRetranTime 1.1.890.1.5.13.5.9.7.4.2.1.17
init retransmit time 100 ~ 20000 ms This MIB object is supported by R5.06 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

h248ProfileMinRetranTime 1.1.890.1.5.13.5.9.7.4.2.1.18
min retransmit time 100 ~ 1000 ms This MIB object is supported by R5.06 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

h248ProfileMaxRetranTime 1.1.890.1.5.13.5.9.7.4.2.1.19
max retransmit time 1000 ~ 20000 ms This MIB object is supported by R5.06 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

h248ProfileRetranWindow 1.1.890.1.5.13.5.9.7.4.2.1.20
retransmit window 1000 ~ 60000 ms This MIB object is supported by R5.06 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

h248ProfileStartTimeout 1.1.890.1.5.13.5.9.7.4.2.1.21
start timeout 0 ~ 99 seconds This MIB object is supported by R5.06 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

h248ProfileShortTimeout 1.1.890.1.5.13.5.9.7.4.2.1.22
short timeout 1 ~ 99 seconds This MIB object is supported by R5.06 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

h248ProfileLongTimeout 1.1.890.1.5.13.5.9.7.4.2.1.23
long timeout 1 ~ 99 seconds This MIB object is supported by R5.06 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

h248ProfileVBD 1.1.890.1.5.13.5.9.7.4.2.1.24
VBD mode support enable/disable This MIB object is supported by R5.06 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

h248ProfileSuffixStartNum 1.1.890.1.5.13.5.9.7.4.2.1.25
suffix start number 1 ~ 15. This MIB object is supported by R5.06 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

h248ProfileSuffixSuffixLen 1.1.890.1.5.13.5.9.7.4.2.1.26
suffix length 0 ~ 15 This MIB object is supported by R5.06 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

h248ProfileRFC2833 1.1.890.1.5.13.5.9.7.4.2.1.27
rfc2833 mode support enable/disable This MIB object is supported by R5.06 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

h248ProfileRFC2833PT 1.1.890.1.5.13.5.9.7.4.2.1.28
rfc2833 payload type 96~127 This MIB object is supported by R5.06 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

h248ProfileT38 1.1.890.1.5.13.5.9.7.4.2.1.29
fax t.38 mode support enable/disable This MIB object is supported by R5.06 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

h248ProfileForceVersion 1.1.890.1.5.13.5.9.7.4.2.1.30
force using h.248 version 1 This MIB object is supported by R5.06 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

h248ProfileLocalcall 1.1.890.1.5.13.5.9.7.4.2.1.31
Turn on the localcall utility This MIB object is supported by R5.08 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

h248ProfileCallthrough 1.1.890.1.5.13.5.9.7.4.2.1.32
Turn on the callthrough utility This MIB object is supported by R5.08 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

maxNumOfDspProfiles 1.1.890.1.5.13.5.9.7.2
The maximum number of DSP profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dspProfileTable 1.1.890.1.5.13.5.9.7.3
This table includes DSP related configuration. This table is supported by R4.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DspProfileEntry

dspProfileEntry 1.1.890.1.5.13.5.9.7.3.1
An entry in dspProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DspProfileEntry  

dspProfileName 1.1.890.1.5.13.5.9.7.3.1.1
This object is used by the DSP profile table in order to identify a row of this table.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

dspProfileCodec 1.1.890.1.5.13.5.9.7.3.1.2
Bit 1: g711a Bit 2: g711mu Bit 3: g723 Bit 4: g726-16 Bit 5: g726-24 Bit 6: g726-32 Bit 7: g726-40 Bit 8: g729ab
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

dspProfilePlayBufferMinDelay 1.1.890.1.5.13.5.9.7.3.1.3
Play buffer minimum delay in milliseconds. It should be less than or equal to dspProfilePlayBufferMaxDelay.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 10..500  

dspProfilePlayBufferMaxDelay 1.1.890.1.5.13.5.9.7.3.1.4
Play buffer maximum delay in milliseconds. It should be greater than or equal to dspProfilePlayBufferMinDelay.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 10..500  

dspProfileEchoTail 1.1.890.1.5.13.5.9.7.3.1.5
Echo cancellation echo tail period in milliseconds.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER echotail-8(1), echotail-16(2), echotail-32(3), echotail-128(4)  

dspProfileRowStatus 1.1.890.1.5.13.5.9.7.3.1.6
This object is used to create a new row or delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

dspProfileEchocancelOn 1.1.890.1.5.13.5.9.7.3.1.7
Echo cancellation.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

dspProfileVadOn 1.1.890.1.5.13.5.9.7.3.1.8
voice activity detection.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

dspProfileg711vpi 1.1.890.1.5.13.5.9.7.3.1.9
G.711 voice packet interval time in milliseconds.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER interval-10ms(1), interval-20ms(2), interval-30ms(3), interval-40ms(4)  

dspProfileg723vpi 1.1.890.1.5.13.5.9.7.3.1.10
G.723 voice packet interval time in milliseconds.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER interval-30ms(1), interval-60ms(2)  

dspProfileg726vpi 1.1.890.1.5.13.5.9.7.3.1.11
G.726 voice packet interval time in milliseconds.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER interval-10ms(1), interval-20ms(2), interval-30ms(3), interval-40ms(4)  

dspProfileg729vpi 1.1.890.1.5.13.5.9.7.3.1.12
G.729 voice packet interval time in milliseconds.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER interval-10ms(1), interval-20ms(2), interval-30ms(3), interval-40ms(4), interval-50ms(5), interval-60ms(6)  

dspProfilePbit 1.1.890.1.5.13.5.9.7.3.1.13
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

dspProfileDscp 1.1.890.1.5.13.5.9.7.3.1.14
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..63  

dspProfileCodecPriority 1.1.890.1.5.13.5.9.7.3.1.15
every octet mean a codec, the order of octets means codec priority. 0x1: g711a 0x2: g711mu 0x3: g723 0x4: g726-16 0x5: g726-24 0x6: g726-32 0x7: g726-40 0x8: g729ab
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

maxNumOfIpqosProfiles 1.1.890.1.5.13.5.9.8.1
The maximum number of IPQOS profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipqosProfileTable 1.1.890.1.5.13.5.9.8.2
This table includes IPQOS related configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpqosProfileEntry

ipqosProfileEntry 1.1.890.1.5.13.5.9.8.2.1
An entry in ipqosProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpqosProfileEntry  

ipqosProfileName 1.1.890.1.5.13.5.9.8.2.1.1
This object is used by the IPQOS profile table in order to identify a row of this table.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

ipqosProfileNumOfQueue 1.1.890.1.5.13.5.9.8.2.1.2
The number of IPQOS queues.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

ipqosProfileRowStatus 1.1.890.1.5.13.5.9.8.2.1.3
This object is used to create a new row or delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

ipqosProfileQueueTable 1.1.890.1.5.13.5.9.8.3
This table includes IPQOS queue related configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpqosProfileQueueEntry

ipqosProfileQueueEntry 1.1.890.1.5.13.5.9.8.3.1
An entry in ipqosProfileQueueTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpqosProfileQueueEntry  

ipqosProfileQueueIndex 1.1.890.1.5.13.5.9.8.3.1.1
IPQOS queue index.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipqosProfileQueuePIR 1.1.890.1.5.13.5.9.8.3.1.2
Peak rate.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

ipqosProfileQueueCIR 1.1.890.1.5.13.5.9.8.3.1.3
Commited rate.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

ipqosProfileQueuePBS 1.1.890.1.5.13.5.9.8.3.1.4
Peak burst size.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

ipqosProfileQueueCBS 1.1.890.1.5.13.5.9.8.3.1.5
Commited burst size.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

ipqosProfileQueueLevel 1.1.890.1.5.13.5.9.8.3.1.6
Queue level.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

ipqosProfileQueueWeight 1.1.890.1.5.13.5.9.8.3.1.7
Queue weight.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..127  

maxNumOfRateLimitProfiles 1.1.890.1.5.13.5.9.9.1
The maximum number of Rate Limit profiles supported by the system. This object is supported by R5.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

rateLimitProfileTable 1.1.890.1.5.13.5.9.9.2
This table includes Rate Limit related configuration. This table is supported by R5.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RateLimitProfileEntry

rateLimitProfileEntry 1.1.890.1.5.13.5.9.9.2.1
An entry in rateLimitProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  RateLimitProfileEntry  

rateLimitProfileName 1.1.890.1.5.13.5.9.9.2.1.1
This object is used by the Rate Limit profile table in order to identify a row of this table.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

rateLimitProfileIngressRate 1.1.890.1.5.13.5.9.9.2.1.2
Ingress rate between 0~100032 in kbps in step of 64, oo0oo means no limiting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100032  

rateLimitProfileEgressRate 1.1.890.1.5.13.5.9.9.2.1.3
Egress rate between 0~100032 in kbps in step of 64, oo0oo means no limiting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..100032  

rateLimitProfileRowStatus 1.1.890.1.5.13.5.9.9.2.1.4
This object is used to create a new row or delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

maxNumOfE1AlarmProfile 1.1.890.1.5.13.5.9.10.1
The maximum number of E1 Alarm profiles supported by the system. This object is supported by R5.03 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e1AlarmProfileTable 1.1.890.1.5.13.5.9.10.2
This table includes Rate Limit related configuration. This table is supported by R5.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    E1AlarmProfileEntry

e1AlarmProfileEntry 1.1.890.1.5.13.5.9.10.2.1
An entry in e1AlarmProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  E1AlarmProfileEntry  

e1AlarmProfileName 1.1.890.1.5.13.5.9.10.2.1.1
This object is used by the E1 Alarm profile table in order to identify a row of this table.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

e1AlarmProfileQEs 1.1.890.1.5.13.5.9.10.2.1.2
15Min error second
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..900  

e1AlarmProfileQSes 1.1.890.1.5.13.5.9.10.2.1.3
15Min severe error second
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..900  

e1AlarmProfileQUas 1.1.890.1.5.13.5.9.10.2.1.4
15Min un-available second
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..900  

e1AlarmProfileDayEs 1.1.890.1.5.13.5.9.10.2.1.5
1Day error second
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..900  

e1AlarmProfileDaySes 1.1.890.1.5.13.5.9.10.2.1.6
1Day severe error second
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..900  

e1AlarmProfileDayUas 1.1.890.1.5.13.5.9.10.2.1.7
1Day un-available second
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..900  

e1AlarmProfileRowStatus 1.1.890.1.5.13.5.9.10.2.1.8
This object is used to create a new row or delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

maxNumOfVdsl2TemplateProfiles 1.1.890.1.5.13.5.9.11.1
The maximum number of VDSL2 template profiles supported by the system. This MIB object is supported by R5.06 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

maxNumOfVdsl2LineProfiles 1.1.890.1.5.13.5.9.11.2
The maximum number of VDSL2 line profiles supported by the system. This MIB object is supported by R5.06 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

maxNumOfVdsl2ChanProfiles 1.1.890.1.5.13.5.9.11.3
The maximum number of VDSL2 chan profiles supported by the system. This MIB object is supported by R5.06 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

maxNumOfVdsl2AlarmTemplateProfiles 1.1.890.1.5.13.5.9.11.4
The maximum number of VDSL2 alarm template profiles supported by the system. This MIB object is supported by R5.06 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

maxNumOfVdsl2AlarmLineProfiles 1.1.890.1.5.13.5.9.11.5
The maximum number of VDSL2 alarm line profiles supported by the system. This MIB object is supported by R5.06 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

maxNumOfVdsl2AlarmChanProfiles 1.1.890.1.5.13.5.9.11.6
The maximum number of VDSL2 alarm chan profiles supported by the system. This MIB object is supported by R5.06 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdsl2LineConfProfileExtendedTable 1.1.890.1.5.13.5.9.11.7
This table contains information on the VDSL2 line profile extension configuration. This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Vdsl2LineConfProfileExtendedEntry

vdsl2LineConfProfileExtendedEntry 1.1.890.1.5.13.5.9.11.7.1
An entry in vdsl2LineProfileExtendedEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Vdsl2LineConfProfileExtendedEntry  

vdsl2LineProfDpboEPsdID 1.1.890.1.5.13.5.9.11.7.1.1
standard psd shape id for psd toolbox
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER psd-co(1), psd-flat(2), psd-cab-ansi(3), psd-cab-etsi(4), psd-exch-etsi(5), psd-exch-ansi(6)  

vdsl2LineProfBitSwapDs 1.1.890.1.5.13.5.9.11.7.1.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

vdsl2LineProfBitSwapUs 1.1.890.1.5.13.5.9.11.7.1.3
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

vdsl2LineProfProfileName 1.1.890.1.5.13.5.9.11.7.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

vdsl2LineProfDynamicDepthEnableDs 1.1.890.1.5.13.5.9.11.7.1.5
Enable the dynamic change of interleave depth.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

vdsl2LineProfDynamicDepthEnableUs 1.1.890.1.5.13.5.9.11.7.1.6
Enable the dynamic change of interleave depth.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

vdsl2LineProfSosTimeDs 1.1.890.1.5.13.5.9.11.7.1.7
The parameter SOS-TIME-ds is used in the specification of the receiver initiated SOS (see 13.4.3/G.993.2). If the value of this parameter is not zero, the standard SOS triggering criteria are enabled, and the value corresponds with duration of the time window used in the standard SOS triggering criteria in the downstream direction. See G.993.2 for detailed usage rules. The special value zero indicates that the standard SOS triggering criteria are disabled, i.e., vendor-discretionary values may be used instead of the values configured in the MIB for the following parameters: SOS-NTONES-ds, SOS-CRC-ds, SOS-TIME-ds. This parameter applies in the downstream direction. The valid range of non-zero values is from 64 ms to 16320 ms in steps of 64 ms.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdsl2LineProfSosTimeUs 1.1.890.1.5.13.5.9.11.7.1.8
The parameter SOS-TIME-u s is used in the specification of the receiver initiated SOS (see 13.4.3/G.993.2). If the value of this parameter is not zero, the standard SOS triggering criteria are enabled, and the value corresponds with duration of the time window used in the standard SOS triggering criteria in the downstream direction. See G.993.2 for detailed usage rules. The special value zero indicates that the standard SOS triggering criteria are disabled, i.e., vendor-discretionary values may be used instead of the values configured in the MIB for the following parameters: SOS-NTONES-ds, SOS-CRC-ds, SOS-TIME-ds. This parameter applies in the downstream direction. The valid range of non-zero values is from 64 ms to 16320 ms in steps of 64 ms.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdsl2LineProfSosCrcDs 1.1.890.1.5.13.5.9.11.7.1.9
This parameter is defined as the minimum number of normalized CRC anomalies received in SOS-TIME-ds seconds in order to arm the second sub condition of the standard SOS triggering criteria (see 13.4.3.2/G.993.2) in the downstream direction. See G.993.2 for detailed usage rules. The valid range of SOS-CRC values is 0.02 to ((2^16)-1)*0.02, in steps of 0.02.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdsl2LineProfSosCrcUs 1.1.890.1.5.13.5.9.11.7.1.10
This parameter is defined as the minimum number of normalized CRC anomalies received in SOS-TIME-ds seconds in order to arm the second sub condition of the standard SOS triggering criteria (see 13.4.3.2/G.993.2) in the downstream direction. See G.993.2 for detailed usage rules. The valid range of SOS-CRC values is 0.02 to ((2^16)-1)*0.02, in steps of 0.02.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdsl2LineProfSosNToneDs 1.1.890.1.5.13.5.9.11.7.1.11
This parameter is defined as the minimum percentage of tones in the downstream MEDLEY SET that must be degraded in order to arm the first sub-condition of the standard SOS triggering criteria (see 13.4.3.2/G.993.2) in the downstream direction. The parameter SOS-NTONES-ds is defined as a percentage of tones. See G.993.2 for detailed usage rules. The valid range of values is from 1 to 100 in steps of 1. Use of the special value 0 is described in 13.4.3.2/G.993.2.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdsl2LineProfSosNToneUs 1.1.890.1.5.13.5.9.11.7.1.12
This parameter is defined as the minimum percentage of tones in the downstream MEDLEY SET that must be degraded in order to arm the first sub-condition of the standard SOS triggering criteria (see 13.4.3.2/G.993.2) in the downstream direction. The parameter SOS-NTONES-ds is defined as a percentage of tones. See G.993.2 for detailed usage rules. The valid range of values is from 1 to 100 in steps of 1. Use of the special value 0 is described in 13.4.3.2/G.993.2.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdsl2LineProfSosMaxDs 1.1.890.1.5.13.5.9.11.7.1.13
This parameter is used in G.993.2 de-activation (see 12.1.4/G.993.2). If the number of successful SOS procedures in the downstream direction performed within a 120-second interval exceeds MAX-SOS-ds, the modem shall transition to the L3 state. See G.993.2 for detailed usage rules (see 12.1.4/G.993.2). The valid range of values is 1 to 15. Use of the special value 0 is described in 12.1/G.993.2.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdsl2LineProfSosMaxUs 1.1.890.1.5.13.5.9.11.7.1.14
This parameter is used in G.993.2 de-activation (see 12.1.4/G.993.2). If the number of successful SOS procedures in the downstream direction performed within a 120-second interval exceeds MAX-SOS-ds, the modem shall transition to the L3 state. See G.993.2 for detailed usage rules (see 12.1.4/G.993.2). The valid range of values is 1 to 15. Use of the special value 0 is described in 12.1/G.993.2.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdsl2LineProfSosMultiStepDs 1.1.890.1.5.13.5.9.11.7.1.15
Indicates the capabilities of the VTU-R to execute the SOS request in one step or in multiple steps in the downstream direction. The field is formatted as [gggg 0000]. The first four MSBs [gggg] indicate the maximum number of tones (GSOS) that can be executed in a single step (GSOS)in the downstream direction. The valid values are: - [0000]: No limitation - [0010]: GSOS = 256 tones - [0011]: GSOS = 512 tones - [0100]: GSOS = 1024 tones
Status: current Access: read-write
OBJECT-TYPE    
  BITS  

vdsl2LineProfSosMultiStepUs 1.1.890.1.5.13.5.9.11.7.1.16
Indicates the capabilities of the VTU-R to execute the SOS request in one step or in multiple steps in the downstream direction. The field is formatted as [gggg 0000]. The first four MSBs [gggg] indicate the maximum number of tones (GSOS) that can be executed in a single step (GSOS)in the downstream direction. The valid values are: - [0000]: No limitation - [0010]: GSOS = 256 tones - [0011]: GSOS = 512 tones - [0100]: GSOS = 1024 tones
Status: current Access: read-write
OBJECT-TYPE    
  BITS  

vdsl2LineProfRocEnableDs 1.1.890.1.5.13.5.9.11.7.1.17
Enable the robust overhead channel.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

vdsl2LineProfRocEnableUs 1.1.890.1.5.13.5.9.11.7.1.18
Enable the robust overhead channel.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

vdsl2LineProfRocSnrmDs 1.1.890.1.5.13.5.9.11.7.1.19
The parameter is defined as the SNR margin offset for the ROC channel in the downstream direction. The parameter is used in the specification of the channel initialization policy (see 12.3.7.1/G.993.2). The valid range of SNR margin offset values is from 0 to 31 dB with 0.1 dB steps.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdsl2LineProfRocSnrmUs 1.1.890.1.5.13.5.9.11.7.1.20
The parameter is defined as the SNR margin offset for the ROC channel in the downstream direction. The parameter is used in the specification of the channel initialization policy (see 12.3.7.1/G.993.2). The valid range of SNR margin offset values is from 0 to 31 dB with 0.1 dB steps.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdsl2LineProfRocMinInpDs 1.1.890.1.5.13.5.9.11.7.1.21
This parameter contains the minimum impulse noise protection to apply on the ROC in the downstream direction. The minimum impulse noise protection is an integer ranging from 0 to 16.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdsl2LineProfRocMinInpUs 1.1.890.1.5.13.5.9.11.7.1.22
This parameter contains the minimum impulse noise protection to apply on the ROC in the downstream direction. The minimum impulse noise protection is an integer ranging from 0 to 16.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdsl2LineProfDpboType 1.1.890.1.5.13.5.9.11.7.1.23
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER g9971(1), t-com(2)  

vdsl2LineProfDpboEselMin 1.1.890.1.5.13.5.9.11.7.1.24
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..511  

vdsl2LineProfCompatible 1.1.890.1.5.13.5.9.11.7.1.25
Compatible to spectrum usage of adsl2 or adsl2+ line.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), adsl2(2), adsl2Plus(3)  

vdsl2LineProfTransmissionType 1.1.890.1.5.13.5.9.11.7.1.26
Configure the desired transmission types. They are: vdsl2(0) adsl2+(1) adsl2(2) gdmt(3) t1413(4) glite(5) annex-m(6) annex-l(7)
Status: current Access: read-write
OBJECT-TYPE    
  BITS  

vdsl2ChanConfProfileExtendedTable 1.1.890.1.5.13.5.9.11.8
This table contains information on the VDSL2 channel profile extension configuration. This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Vdsl2ChanConfProfileExtendedEntry

vdsl2ChanConfProfileExtendedEntry 1.1.890.1.5.13.5.9.11.8.1
An entry in vdsl2ChanConfProfileExtendedEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Vdsl2ChanConfProfileExtendedEntry  

vdsl2ChanConfProfphyRds 1.1.890.1.5.13.5.9.11.8.1.1
retransmission mode
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), auto(3)  

vdsl2ChanConfProfphyRus 1.1.890.1.5.13.5.9.11.8.1.2
retransmission mode
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2), auto(3)  

vdsl2ChanConfProfProfileName 1.1.890.1.5.13.5.9.11.8.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

vdsl2ChanConfProfGinpRtxModeDs 1.1.890.1.5.13.5.9.11.8.1.4
G.inp(G.998.4) support setting on downstream direction. The possible values are: Forbidden(0) - Support for G998.4 is disabled. Preferred(1) - If G998.4 is supported by the far-end, it is enabled. Forced(2) - The line will only train if G998.4 can be enabled. Test(3) - G998.4 is enabled in test mode (refer to G998.4, Clause 10.4).
Status: current Access: read-create
OBJECT-TYPE    
  Xdsl2ConfigRtxMode  

vdsl2ChanConfProfGinpRtxModeUs 1.1.890.1.5.13.5.9.11.8.1.5
G.inp(G.998.4) support setting on upstream direction. The possible values are: Forbidden(0) - Support for G998.4 is disabled. Preferred(1) - If G998.4 is supported by the far-end, it is enabled. Forced(2) - The line will only train if G998.4 can be enabled. Test(3) - G998.4 is enabled in test mode (refer to G998.4, Clause 10.4).
Status: current Access: read-create
OBJECT-TYPE    
  Xdsl2ConfigRtxMode  

vdsl2ChanConfProfGinpEtrMaxDs 1.1.890.1.5.13.5.9.11.8.1.6
Defines the maximum allowed value for the ETR (Effective Throughput Rate).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfGinpEtrMaxUs 1.1.890.1.5.13.5.9.11.8.1.7
Defines the maximum allowed value for the ETR (Effective Throughput Rate).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfGinpEtrMinDs 1.1.890.1.5.13.5.9.11.8.1.8
Defines the minimum value for the ETR (Effective Throughput Rate).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfGinpEtrMinUs 1.1.890.1.5.13.5.9.11.8.1.9
Defines the minimum value for the ETR (Effective Throughput Rate).
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfGinpNdrMaxDs 1.1.890.1.5.13.5.9.11.8.1.10
Overrules the wanted maximum data rate provided in the SetLineTrafficConfiguration
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfGinpNdrMaxUs 1.1.890.1.5.13.5.9.11.8.1.11
Overrules the wanted maximum data rate provided in the SetLineTrafficConfiguration
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfGinpShineRatioDs 1.1.890.1.5.13.5.9.11.8.1.12
The assumed fraction (0.001 to 0.255) of NDR necessary to correct SHINE noise.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfGinpShineRatioUs 1.1.890.1.5.13.5.9.11.8.1.13
The assumed fraction (0.001 to 0.255) of NDR necessary to correct SHINE noise.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfGinpLeftrThresholdDs 1.1.890.1.5.13.5.9.11.8.1.14
The rate threshold (fraction of NDR) below which the Low Error Free Rate (LEFTR) defect is declared.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfGinpLeftrThresholdUs 1.1.890.1.5.13.5.9.11.8.1.15
The rate threshold (fraction of NDR) below which the Low Error Free Rate (LEFTR) defect is declared.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfGinpMaxDelayDs 1.1.890.1.5.13.5.9.11.8.1.16
G.inp-specific value that overrules the traffic configuration setting.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfGinpMaxDelayUs 1.1.890.1.5.13.5.9.11.8.1.17
G.inp-specific value that overrules the traffic configuration setting.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfGinpMinDelayDs 1.1.890.1.5.13.5.9.11.8.1.18
G.inp-specific value that overrules the traffic configuration setting.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfGinpMinDelayUs 1.1.890.1.5.13.5.9.11.8.1.19
G.inp-specific value that overrules the traffic configuration setting.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfGinpInpMinDs 1.1.890.1.5.13.5.9.11.8.1.20
G.inp-specific value that overrules the traffic configuration setting. Unit is symbol. The possible values are: 0-31
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfGinpInpMinUs 1.1.890.1.5.13.5.9.11.8.1.21
G.inp-specific value that overrules the traffic configuration setting. Unit is symbol. The possible values are: 0-31
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfGinpReinCfgInpDs 1.1.890.1.5.13.5.9.11.8.1.22
G.inp-specific value that overrules the traffic configuration setting. Unit is symbol. The possible values are: 0-7
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfGinpReinCfgInpUs 1.1.890.1.5.13.5.9.11.8.1.23
G.inp-specific value that overrules the traffic configuration setting. Unit is symbol. The possible values are: 0-7
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfGinpReinCfgFreqDs 1.1.890.1.5.13.5.9.11.8.1.24
G.inp-specific value that overrules the traffic configuration setting. Unit is Hz. The possible values are: 100 - 100Hz 120 - 120Hz
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfGinpReinCfgFreqUs 1.1.890.1.5.13.5.9.11.8.1.25
G.inp-specific value that overrules the traffic configuration setting. Unit is Hz. The possible values are: 100 - 100Hz 120 - 120Hz
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfSosMinRateB0Ds 1.1.890.1.5.13.5.9.11.8.1.26
This parameter specifies the minimum net data rate required for a valid SOS request in the downstream direction. The value shall be coded as an unsigned integer representing the data rate as a multiple of 8 kbit/s.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2ChanConfProfSosMinRateB0Us 1.1.890.1.5.13.5.9.11.8.1.27
This parameter specifies the minimum net data rate required for a valid SOS request in the downstream direction. The value shall be coded as an unsigned integer representing the data rate as a multiple of 8 kbit/s.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32  

vdsl2LineAlarmConfProfileExtendedTable 1.1.890.1.5.13.5.9.11.9
This table contains information on the VDSL2 line alarm profile extension configuration. This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Vdsl2LineAlarmConfProfileExtendedEntry

vdsl2LineAlarmConfProfileExtendedEntry 1.1.890.1.5.13.5.9.11.9.1
An entry in vdsl2LineAlarmConfProfileExtendedEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Vdsl2LineAlarmConfProfileExtendedEntry  

xdsl2LineAlarmConfProfileXtucThresh15MinLofs 1.1.890.1.5.13.5.9.11.9.1.1
A threshold for the xdsl2PMLCurr15MLofs counter, when xdsl2PMLCurrUnit is xtuc 1. The value 0 means that no threshold is specified for the associated counter. Units:seconds
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

xdsl2LineAlarmConfProfileXturThresh15MinLofs 1.1.890.1.5.13.5.9.11.9.1.2
A threshold for the xdsl2PMLCurr15MLofs counter, when xdsl2PMLCurrUnit is xtur 2. The value 0 means that no threshold is specified for the associated counter. Units:seconds
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

xdsl2LineAlarmConfProfileThresh15MinLprs 1.1.890.1.5.13.5.9.11.9.1.3
A threshold for the xdsl2PMLCurr15MLprs counter. The value 0 means that no threshold is specified for the associated counter. Units:seconds
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

xdsl2LineAlarmConfProfileProfileName 1.1.890.1.5.13.5.9.11.9.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

xdsl2LineAlarmConfProfileXtucThresh15MinLols 1.1.890.1.5.13.5.9.11.9.1.5
A threshold for the xdsl2PMLCurr15MLols counter, when xdsl2PMLCurrUnit is xtuc. The value 0 means that no threshold is specified for the associated counter. Units:seconds
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

vdsl2LineConfTempExtendedTable 1.1.890.1.5.13.5.9.11.10
This table contains information on the VDSL2 line template profile extension configuration. This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Vdsl2LineConfTempExtendedEntry

vdsl2LineConfTempExtendedEntry 1.1.890.1.5.13.5.9.11.10.1
An entry in vdsl2LineConfTempExtendedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Vdsl2LineConfTempExtendedEntry  

vdsl2LineConfTempTemplateName 1.1.890.1.5.13.5.9.11.10.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

vdsl2LineConfTempTemplatePortMap 1.1.890.1.5.13.5.9.11.10.1.2
Profile mapping port list
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

vdsl2LineConfTempInmProfile 1.1.890.1.5.13.5.9.11.10.1.3
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

vdsl2AlarmConfTempExtendedTable 1.1.890.1.5.13.5.9.11.11
This table contains information on the VDSL2 line alarm template profile extension configuration. This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Vdsl2AlarmConfTempExtendedEntry

vdsl2AlarmConfTempExtendedEntry 1.1.890.1.5.13.5.9.11.11.1
An entry in vdsl2AlarmConfTempExtendedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Vdsl2AlarmConfTempExtendedEntry  

vdsl2AlarmConfTempTemplateName 1.1.890.1.5.13.5.9.11.11.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

vdsl2ChanAlarmConfProfileExtendedTable 1.1.890.1.5.13.5.9.11.12
This table contains information on the VDSL2 channel alarm profile extension configuration. This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Vdsl2ChanAlarmConfProfileExtendedEntry

vdsl2ChanAlarmConfProfileExtendedEntry 1.1.890.1.5.13.5.9.11.12.1
An entry in vdsl2ChanAlarmConfProfileExtendedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Vdsl2ChanAlarmConfProfileExtendedEntry  

vdsl2ChanAlarmConfProfProfileName 1.1.890.1.5.13.5.9.11.12.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

maxNumOfVdsl2InmProfiles 1.1.890.1.5.13.5.9.11.13
The maximum number of VDSL2 Inm profiles supported by the system. This MIB object is supported by R5.06 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdsl2InmConfProfileExtendedTable 1.1.890.1.5.13.5.9.11.14
vdsl2InmConfProfileExtendedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Vdsl2InmConfProfileExtendedEntry

vdsl2InmConfProfileExtendedEntry 1.1.890.1.5.13.5.9.11.14.1
vdsl2InmConfProfileExtendedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Vdsl2InmConfProfileExtendedEntry  

xdsl2InmConfProfProfileName 1.1.890.1.5.13.5.9.11.14.1.1
This object identifies a row in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..32)  

xdsl2InmConfProfVtucInpEq 1.1.890.1.5.13.5.9.11.14.1.2
The INM Inmpulse Noise Protection Equivalent Mode. Configuration parameter INM-INPEQ-MODE defines the way of computation of Equivalent INP, as defined in ITU-T G.993.2 Amd2 11.4.2.2.1 This takes a value in the range from 0 to 3.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..3  

xdsl2InmConfProfVturInpEq 1.1.890.1.5.13.5.9.11.14.1.3
The INM Inmpulse Noise Protection Equivalent Mode. Configuration parameter INM-INPEQ-MODE defines the way of computation of Equivalent INP, as defined in ITU-T G.993.2 Amd2 11.4.2.2.1 This takes a value in the range from 0 to 3.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..3  

xdsl2InmConfProfVtucCC 1.1.890.1.5.13.5.9.11.14.1.4
The INM Cluster Continuation. The valid values for INMCC range from 0 from 64 DMT symbols in steps of 1 DMT symbol. Up to and including INMCC nondegraded symbols will be allowed before a cluster is deemed to be complete and the impulse noise event over.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

xdsl2InmConfProfVturCC 1.1.890.1.5.13.5.9.11.14.1.5
The INM Cluster Continuation. The valid values for INMCC range from 0 from 64 DMT symbols in steps of 1 DMT symbol. Up to and including INMCC nondegraded symbols will be allowed before a cluster is deemed to be complete and the impulse noise event over.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

xdsl2InmConfProfVtucIATO 1.1.890.1.5.13.5.9.11.14.1.6
The INM Inter Arrival Time Offset for the IAT anomaly generation. The valid values for INMIATO range from 3 from 511 DMT symbols in steps of 1 DMT symbol.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

xdsl2InmConfProfVturIATO 1.1.890.1.5.13.5.9.11.14.1.7
The INM Inter Arrival Time Offset for the IAT anomaly generation. The valid values for INMIATO range from 3 from 511 DMT symbols in steps of 1 DMT symbol.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

xdsl2InmConfProfVtucIATS 1.1.890.1.5.13.5.9.11.14.1.8
The INM Inter Arrival Time Step for the IAT anomaly generation. The valid values for INMIATS range from 0 from 7 in steps. The range of values of inter-arrival times recorded in a single bin is 2^(INMIATS). All inter-arrival times greater than or equal to INMIATO+6*(2^INMIATS) are recorded in the 7th bin of INMAIAT.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

xdsl2InmConfProfVturIATS 1.1.890.1.5.13.5.9.11.14.1.9
The INM Inter Arrival Time Step for the IAT anomaly generation. The valid values for INMIATS range from 0 from 7 in steps. The range of values of inter-arrival times recorded in a single bin is 2^(INMIATS). All inter-arrival times greater than or equal to INMIATO+6*(2^INMIATS) are recorded in the 7th bin of INMAIAT.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

xdsl2InmConfProfRowStatus 1.1.890.1.5.13.5.9.11.14.1.10
This object is used to create a new row or to modify or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

xdsl2InmConfProfVtucISDBUS 1.1.890.1.5.13.5.9.11.14.1.11
ISDD sensitivity of VTU-C, -128~127 in unit of 0.1dB.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

maxNumOfQueueRateLimitProfiles 1.1.890.1.5.13.5.9.12.1
The maximum number of Queue Rate Limit profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

queueRateLimitProfileTable 1.1.890.1.5.13.5.9.12.2
This table includes Queue Rate Limit related configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QueueRateLimitProfileEntry

queueRateLimitProfileEntry 1.1.890.1.5.13.5.9.12.2.1
An entry in queueRateLimitProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  QueueRateLimitProfileEntry  

queueRateLimitProfileName 1.1.890.1.5.13.5.9.12.2.1.1
This object is used by the Queue Rate Limit profile table and Queue Rate Limit Profile Queue table in order to identify a row of these table.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

queueRateLimitProfileQueue0CIR 1.1.890.1.5.13.5.9.12.2.1.2
CIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..99968  

queueRateLimitProfileQueue0PIR 1.1.890.1.5.13.5.9.12.2.1.3
PIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..99968  

queueRateLimitProfileQueue1CIR 1.1.890.1.5.13.5.9.12.2.1.4
CIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..99968  

queueRateLimitProfileQueue1PIR 1.1.890.1.5.13.5.9.12.2.1.5
PIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..99968  

queueRateLimitProfileQueue2CIR 1.1.890.1.5.13.5.9.12.2.1.6
CIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..99968  

queueRateLimitProfileQueue2PIR 1.1.890.1.5.13.5.9.12.2.1.7
PIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..99968  

queueRateLimitProfileQueue3CIR 1.1.890.1.5.13.5.9.12.2.1.8
CIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..99968  

queueRateLimitProfileQueue3PIR 1.1.890.1.5.13.5.9.12.2.1.9
PIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..99968  

queueRateLimitProfileQueue4CIR 1.1.890.1.5.13.5.9.12.2.1.10
CIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..99968  

queueRateLimitProfileQueue4PIR 1.1.890.1.5.13.5.9.12.2.1.11
PIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..99968  

queueRateLimitProfileQueue5CIR 1.1.890.1.5.13.5.9.12.2.1.12
CIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..99968  

queueRateLimitProfileQueue5PIR 1.1.890.1.5.13.5.9.12.2.1.13
PIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..99968  

queueRateLimitProfileQueue6CIR 1.1.890.1.5.13.5.9.12.2.1.14
CIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..99968  

queueRateLimitProfileQueue6PIR 1.1.890.1.5.13.5.9.12.2.1.15
PIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..99968  

queueRateLimitProfileQueue7CIR 1.1.890.1.5.13.5.9.12.2.1.16
CIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..99968  

queueRateLimitProfileQueue7PIR 1.1.890.1.5.13.5.9.12.2.1.17
PIR of a queue between 0~99968 in kbps in step of 64,'0' means no limiting.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..99968  

queueRateLimitProfileRowStatus 1.1.890.1.5.13.5.9.12.2.1.18
This object is used to create a new row or delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

maxNumOfIpqos2Profiles 1.1.890.1.5.13.5.9.13.1
The maximum number of IPQoS2 profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipqos2ProfileTable 1.1.890.1.5.13.5.9.13.2
This table includes IPQoS2 profiles.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Ipqos2ProfileEntry

ipqos2ProfileEntry 1.1.890.1.5.13.5.9.13.2.1
An entry in ipqos2ProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Ipqos2ProfileEntry  

ipqos2ProfileName 1.1.890.1.5.13.5.9.13.2.1.1
profile name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

ipqos2ProfileAlgorithm 1.1.890.1.5.13.5.9.13.2.1.2
1:sp, 2:wfq, 3-sp+wfq, 4:shaping, 5:vc-shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..5  

ipqos2ProfileVcLevel 1.1.890.1.5.13.5.9.13.2.1.3
level of the PVC. For vc-shaping only. Displayed as -1 when ipqos2ProfileAlgorithm is not vc-shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

ipqos2ProfileVcMaxRate 1.1.890.1.5.13.5.9.13.2.1.4
max rate of the queues of PVCs. For vc-shaping only. Displayed as -1 when ipqos2ProfileAlgorithm is not vc-shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 32..32000  

ipqos2ProfileVcDepth 1.1.890.1.5.13.5.9.13.2.1.5
depth of queues of PVCs. For vc-shaping only. Displayed as -1 when ipqos2ProfileAlgorithm is not vc-shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 30..255  

ipqos2ProfileQueue0Weight 1.1.890.1.5.13.5.9.13.2.1.6
weight of queue 0 of PVCs. For wfq, sp+wfq only. Displayed as -1 when ipqos2ProfileAlgorithm is not wfq, sp+wfq.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..50  

ipqos2ProfileQueue0MaxRate 1.1.890.1.5.13.5.9.13.2.1.7
max rate of queue 0 of PVCs. For shaping only. Displayed as -1 when ipqos2ProfileAlgorithm is not shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 32..32000  

ipqos2ProfileQueue0Depth 1.1.890.1.5.13.5.9.13.2.1.8
depth of queue 0 of PVCs. For wfq, sp+wfq, shaping. Displayed as -1 when ipqos2ProfileAlgorithm is not wfq, sp+wfq, shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 30..255  

ipqos2ProfileQueue1Weight 1.1.890.1.5.13.5.9.13.2.1.9
weight of queue 1 of PVCs. For wfq, sp+wfq only. Displayed as -1 when ipqos2ProfileAlgorithm is not wfq, sp+wfq.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..50  

ipqos2ProfileQueue1MaxRate 1.1.890.1.5.13.5.9.13.2.1.10
max rate of queue 1 of PVCs. For shaping only. Displayed as -1 when ipqos2ProfileAlgorithm is not shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 32..32000  

ipqos2ProfileQueue1Depth 1.1.890.1.5.13.5.9.13.2.1.11
depth of queue 1 of PVCs. For wfq, sp+wfq, shaping. Displayed as -1 when ipqos2ProfileAlgorithm is not wfq, sp+wfq, shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 30..255  

ipqos2ProfileQueue2Weight 1.1.890.1.5.13.5.9.13.2.1.12
weight of queue 2 of PVCs. For wfq, sp+wfq only. Displayed as -1 when ipqos2ProfileAlgorithm is not wfq, sp+wfq.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..50  

ipqos2ProfileQueue2MaxRate 1.1.890.1.5.13.5.9.13.2.1.13
max rate of queue 2 of PVCs. For shaping only. Displayed as -1 when ipqos2ProfileAlgorithm is not shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 32..32000  

ipqos2ProfileQueue2Depth 1.1.890.1.5.13.5.9.13.2.1.14
depth of queue 2 of PVCs. For wfq, sp+wfq, shaping. Displayed as -1 when ipqos2ProfileAlgorithm is not wfq, sp+wfq, shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 30..255  

ipqos2ProfileQueue3Weight 1.1.890.1.5.13.5.9.13.2.1.15
weight of queue 3 of PVCs. For wfq, sp+wfq only. Displayed as -1 when ipqos2ProfileAlgorithm is not wfq, sp+wfq.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..50  

ipqos2ProfileQueue3MaxRate 1.1.890.1.5.13.5.9.13.2.1.16
max rate of queue 3 of PVCs. For shaping only. Displayed as -1 when ipqos2ProfileAlgorithm is not shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 32..32000  

ipqos2ProfileQueue3Depth 1.1.890.1.5.13.5.9.13.2.1.17
depth of queue 3 of PVCs. For wfq, sp+wfq, shaping. Displayed as -1 when ipqos2ProfileAlgorithm is not wfq, sp+wfq, shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 30..255  

ipqos2ProfileQueue4Weight 1.1.890.1.5.13.5.9.13.2.1.18
weight of queue 4 of PVCs. For wfq, sp+wfq only. Displayed as -1 when ipqos2ProfileAlgorithm is not wfq, sp+wfq.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..50  

ipqos2ProfileQueue4MaxRate 1.1.890.1.5.13.5.9.13.2.1.19
max rate of queue 4 of PVCs. For shaping only. Displayed as -1 when ipqos2ProfileAlgorithm is not shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 32..32000  

ipqos2ProfileQueue4Depth 1.1.890.1.5.13.5.9.13.2.1.20
depth of queue 4 of PVCs. For wfq, sp+wfq, shaping. Displayed as -1 when ipqos2ProfileAlgorithm is not wfq, sp+wfq, shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 30..255  

ipqos2ProfileQueue5Weight 1.1.890.1.5.13.5.9.13.2.1.21
weight of queue 5 of PVCs. For wfq, sp+wfq only. Displayed as -1 when ipqos2ProfileAlgorithm is not wfq, sp+wfq, shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..50  

ipqos2ProfileQueue5MaxRate 1.1.890.1.5.13.5.9.13.2.1.22
max rate of queue 5 of PVCs. For shaping only. Displayed as -1 when ipqos2ProfileAlgorithm is not shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 32..32000  

ipqos2ProfileQueue5Depth 1.1.890.1.5.13.5.9.13.2.1.23
depth of queue 5 of PVCs. For wfq, sp+wfq, shaping. Displayed as -1 when ipqos2ProfileAlgorithm is not wfq, sp+wfq, shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 30..255  

ipqos2ProfileQueue6Weight 1.1.890.1.5.13.5.9.13.2.1.24
weight of queue 6 of PVCs. For wfq, sp+wfq only. Displayed as -1 when ipqos2ProfileAlgorithm is not wfq, sp+wfq.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..50  

ipqos2ProfileQueue6MaxRate 1.1.890.1.5.13.5.9.13.2.1.25
max rate of queue 6 of PVCs. For shaping only. Displayed as -1 when ipqos2ProfileAlgorithm is not shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 32..32000  

ipqos2ProfileQueue6Depth 1.1.890.1.5.13.5.9.13.2.1.26
depth of queue 6 of PVCs. For wfq, sp+wfq, shaping. Displayed as -1 when ipqos2ProfileAlgorithm is not wfq, sp+wfq, shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 30..255  

ipqos2ProfileQueue7Weight 1.1.890.1.5.13.5.9.13.2.1.27
weight of queue 7 of PVCs. For wfq, sp+wfq only. Displayed as -1 when ipqos2ProfileAlgorithm is not wfq, sp+wfq.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..50  

ipqos2ProfileQueue7MaxRate 1.1.890.1.5.13.5.9.13.2.1.28
max rate of queue 7 of PVCs. For shaping only. Displayed as -1 when ipqos2ProfileAlgorithm is not shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 32..32000  

ipqos2ProfileQueue7Depth 1.1.890.1.5.13.5.9.13.2.1.29
depth of queue 7 of PVCs. For wfq, sp+wfq, shaping. Displayed as -1 when ipqos2ProfileAlgorithm is not wfq, sp+wfq, shaping.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 30..255  

ipqos2ProfileRowStatus 1.1.890.1.5.13.5.9.13.2.1.30
This object is used to create a new row or delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

enetport 1.1.890.1.5.13.5.10.3
OBJECT IDENTIFIER    

bandwidth 1.1.890.1.5.13.5.10.4
OBJECT IDENTIFIER    

qschedule 1.1.890.1.5.13.5.10.5
OBJECT IDENTIFIER    

dot3ad 1.1.890.1.5.13.5.10.6
OBJECT IDENTIFIER    

stp 1.1.890.1.5.13.5.10.7
OBJECT IDENTIFIER    

bcastCtrl 1.1.890.1.5.13.5.10.8
OBJECT IDENTIFIER    

portIsolation 1.1.890.1.5.13.5.10.9
OBJECT IDENTIFIER    

dscp 1.1.890.1.5.13.5.10.10
OBJECT IDENTIFIER    

mstp 1.1.890.1.5.13.5.10.11
OBJECT IDENTIFIER    

vlanIsolation 1.1.890.1.5.13.5.10.12
OBJECT IDENTIFIER    

mac 1.1.890.1.5.13.5.10.13
OBJECT IDENTIFIER    

cfm 1.1.890.1.5.13.5.10.14
OBJECT IDENTIFIER    

oam 1.1.890.1.5.13.5.10.15
OBJECT IDENTIFIER    

vlanpriority 1.1.890.1.5.13.5.10.16
OBJECT IDENTIFIER    

mirror 1.1.890.1.5.13.5.10.17
OBJECT IDENTIFIER    

lldp 1.1.890.1.5.13.5.10.18
OBJECT IDENTIFIER    

managementVLANId 1.1.890.1.5.13.5.10.1
The VLAN ID for management.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

maxNumOfStaticVlans 1.1.890.1.5.13.5.10.2
The maximum number of VLANs supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

enetPortTable 1.1.890.1.5.13.5.10.3.1
The table contains ethernet port information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnetPortEntry

enetPortEntry 1.1.890.1.5.13.5.10.3.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  EnetPortEntry  

enetPortSpeed 1.1.890.1.5.13.5.10.3.1.1.1
Speed configuration of the ethernet port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER auto(1), e1000M-fullduplex(2), e100M-fullduplex(3), e100M-halfduplex(4), e10M-fullduplex(5), e10M-halfduplex(6), e10G-fullduplex(7)  

enetPortFlowControl 1.1.890.1.5.13.5.10.3.1.1.2
Enable/disable flow control for the ethernet port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

enetPortMode 1.1.890.1.5.13.5.10.3.1.1.3
The operational mode for uplink and subtending ports.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER uplink(1), subtending(2)  

enetPortVLANTrunkEnable 1.1.890.1.5.13.5.10.3.1.1.4
Enable/disable VLAN trunking for the ethernet port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

enetPortDscpEnable 1.1.890.1.5.13.5.10.3.1.1.5
Enable/disable DSCP mapping for the ethernet port. This object is supported by R1.02 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

enetPortTpid 1.1.890.1.5.13.5.10.3.1.1.6
Set TPID value for the ethernet port, 0x0000 ~ 0xffff.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

enetPortSfpTable 1.1.890.1.5.13.5.10.3.2
The table contains ethernet SFP port information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnetPortSfpEntry

enetPortSfpEntry 1.1.890.1.5.13.5.10.3.2.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  EnetPortSfpEntry  

sfpTempLow 1.1.890.1.5.13.5.10.3.2.1.1
temperature low threshold in 0.001 degree.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

sfpTempHigh 1.1.890.1.5.13.5.10.3.2.1.2
temperature high threshold in 0.001 degree.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

sfpVccLow 1.1.890.1.5.13.5.10.3.2.1.3
voltage low threshold in mV.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

sfpVccHigh 1.1.890.1.5.13.5.10.3.2.1.4
voltage high threshold in mV.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

sfpTxBiasLow 1.1.890.1.5.13.5.10.3.2.1.5
bias current low threshold in uA.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

sfpTxBiasHigh 1.1.890.1.5.13.5.10.3.2.1.6
bias current high threshold in uA.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

sfpTxPowerLow 1.1.890.1.5.13.5.10.3.2.1.7
tx power low threshold in 0.001 uW.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

sfpTxPowerHigh 1.1.890.1.5.13.5.10.3.2.1.8
tx power high threshold in 0.001 uW.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

sfpRxPowerLow 1.1.890.1.5.13.5.10.3.2.1.9
tx power low threshold in 0.001 uW.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

sfpRxPowerHigh 1.1.890.1.5.13.5.10.3.2.1.10
tx power high threshold in 0.001 uW.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

bwPortTable 1.1.890.1.5.13.5.10.4.1
The table contains bandwidth configuration for the ethernet ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BwPortEntry

bwPortEntry 1.1.890.1.5.13.5.10.4.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  BwPortEntry  

bwPortEnable 1.1.890.1.5.13.5.10.4.1.1.1
Enable/disable bandwidth control for the ethernet port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

bwPortIngressRate 1.1.890.1.5.13.5.10.4.1.1.2
The ingress rate for the ethernet port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..1000  

bwPortEgressRate 1.1.890.1.5.13.5.10.4.1.1.3
The egress rate for the ethernet port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..1000  

qschedulePortTable 1.1.890.1.5.13.5.10.5.1
The table contains queue schedule configuration for the ethernet ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QschedulePortEntry

qschedulePortEntry 1.1.890.1.5.13.5.10.5.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  QschedulePortEntry  

qschedulePortType 1.1.890.1.5.13.5.10.5.1.1.1
Queue scheduling type (strictly priority queue or weighted round robin).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER spq(1), wrr(2)  

queueWeightTable 1.1.890.1.5.13.5.10.5.2
The table contains weight configuration for the priority queues.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    QueueWeightEntry

queueWeightEntry 1.1.890.1.5.13.5.10.5.2.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  QueueWeightEntry  

queueWeight 1.1.890.1.5.13.5.10.5.2.1.1
Weight for the priority queue.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

dot3adTable 1.1.890.1.5.13.5.10.6.1
The table contains 802.3ad configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Dot3adEntry

dot3adEntry 1.1.890.1.5.13.5.10.6.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  Dot3adEntry  

dot3adGroupId 1.1.890.1.5.13.5.10.6.1.1.1
Group ID 1 for subtending group and 2 for uplink group in IES-5000/5005. Group ID 1~4 in IES-6000.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dot3adEnable 1.1.890.1.5.13.5.10.6.1.1.2
Enable/disable 802.3ad function.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), enableWithLacp(2), disable(3)  

dot3adGroupName 1.1.890.1.5.13.5.10.6.1.1.3
The trunking group name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

dot3adGroupPortList 1.1.890.1.5.13.5.10.6.1.1.4
The port list which joins the trunking group.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

lacpPriority 1.1.890.1.5.13.5.10.6.2
LACP system priority.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

lacpTimeout 1.1.890.1.5.13.5.10.6.3
The time interval to exchange LACP packets in order to check that the peer port in the trunk group is still up.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER shorttimeout(1), longtimeout(2)  

portTrunkingTable 1.1.890.1.5.13.5.10.6.4
The table contains current status of port trunking.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PortTrunkingEntry

portTrunkingEntry 1.1.890.1.5.13.5.10.6.4.1
An entry of portTrunkingTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PortTrunkingEntry  

portTrunkingGroupId 1.1.890.1.5.13.5.10.6.4.1.1
Group ID 1 for subtending group and 2 for uplink group in IES-5000/5005. Group ID 1~4 in IES-6000.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

portTrunkingStatus 1.1.890.1.5.13.5.10.6.4.1.2
Port trunking status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

portTrunkingPortList 1.1.890.1.5.13.5.10.6.4.1.3
The port list which actually joins the trunking group.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

aggPortTable 1.1.890.1.5.13.5.10.6.5
The table specifies the setting of port trunking.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AggPortEntry

aggPortEntry 1.1.890.1.5.13.5.10.6.5.1
An entry of aggPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AggPortEntry  

aggPortJoin 1.1.890.1.5.13.5.10.6.5.1.1
Join/disjoin the trunking group.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disjoin(0), joinTrunkingGroup1(1), joinTrunkingGroup2(2), joinTrunkingGroup3(3), joinTrunkingGroup4(4)  

elcPortTrunkingTable 1.1.890.1.5.13.5.10.6.6
The table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ElcPortTrunkingEntry

elcPortTrunkingEntry 1.1.890.1.5.13.5.10.6.6.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  ElcPortTrunkingEntry  

elcPortTrunkingSlot 1.1.890.1.5.13.5.10.6.6.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

elcPortTrunkingGroupId 1.1.890.1.5.13.5.10.6.6.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

elcPortTrunkingStatus 1.1.890.1.5.13.5.10.6.6.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

elcPortTrunkingPortList 1.1.890.1.5.13.5.10.6.6.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

rstpEnable 1.1.890.1.5.13.5.10.7.1
Enable/disable RSTP protocol.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

bctrlPortTable 1.1.890.1.5.13.5.10.8.1
The table contains broadcast storm control configuration for the ethernet ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BctrlPortEntry

bctrlPortEntry 1.1.890.1.5.13.5.10.8.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  BctrlPortEntry  

bctrlPortBcastEnable 1.1.890.1.5.13.5.10.8.1.1.1
Enable/disable storm control for broadcast packets.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

bctrlPortMcastEnable 1.1.890.1.5.13.5.10.8.1.1.2
Enable/disable storm control for multicast packets.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

bctrlPortUcastEnable 1.1.890.1.5.13.5.10.8.1.1.3
Enable/disable storm control for unicast packets.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

bctrlPortBcastThresh 1.1.890.1.5.13.5.10.8.1.1.4
The threshold of broadcast storm control.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..262143  

bctrlPortMcastThresh 1.1.890.1.5.13.5.10.8.1.1.5
The threshold of multicast storm control.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..262143  

bctrlPortUcastThresh 1.1.890.1.5.13.5.10.8.1.1.6
The threshold of unicast storm control.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..262143  

portIsolationEnable 1.1.890.1.5.13.5.10.9.1
Enable/disable port isolation.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dscpMappingPortTable 1.1.890.1.5.13.5.10.10.1
The table contains DSCP mapping configuration for the ethernet ports. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DscpMappingPortEntry

dscpMappingPortEntry 1.1.890.1.5.13.5.10.10.1.1
An entry of dscpMappingPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DscpMappingPortEntry  

dscpMappingPortSrcCodePoint 1.1.890.1.5.13.5.10.10.1.1.1
The DSCP source code point used for mapping.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dscpMappingPortMapCodePoint 1.1.890.1.5.13.5.10.10.1.1.2
The mapping code point that will replace the source code point in the incoming packet.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..63  

dscpMappingPortMapPriority 1.1.890.1.5.13.5.10.10.1.1.3
The mapping p bits that will replace the source p bits in the incoming packet.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

mstpEnable 1.1.890.1.5.13.5.10.11.1
Enable/disable MSTP protocol. This object is supported by R1.02 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

mstpProtocolVersion 1.1.890.1.5.13.5.10.11.2
The MSTP protocol version. This object is supported by R1.02 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER forceDot1w(2), autoDot1s(3)  

mstpBridgeMaxAge 1.1.890.1.5.13.5.10.11.3
The value that all bridges use for MaxAge when this bridge is acting as the root. This object is supported by R1.02 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  Timeout 600..4000  

mstpBridgeHelloTime 1.1.890.1.5.13.5.10.11.4
The value that all bridges use for HelloTime when this bridge is acting as the root. This object is supported by R1.02 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  Timeout 100..1000  

mstpBridgeForwardDelay 1.1.890.1.5.13.5.10.11.5
The value that all bridges use for ForwardDelay when this bridge is acting as the root. This object is supported by R1.02 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  Timeout 400..3000  

mstpMaxHops 1.1.890.1.5.13.5.10.11.6
The maximum hops that is allowed. This object is supported by R1.02 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

mstpCfgName 1.1.890.1.5.13.5.10.11.7
The configuration name that identifies the MST region and is used as one of the inputs in the computation of the MST Configuration Identifier. This object is supported by R1.02 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

mstpCfgRevLevel 1.1.890.1.5.13.5.10.11.8
This object identifies the MST revision that identifies the MST region and is used as one of the inputs in the computation of the MST configuration Identifier. This object is supported by R1.02 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

mstpCfgDigest 1.1.890.1.5.13.5.10.11.9
Configuration Digest. This object is supported by R1.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(16)  

mstpMapTable 1.1.890.1.5.13.5.10.11.10
This table contains one entry for each instance of MSTP. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MstpMapEntry

mstpMapEntry 1.1.890.1.5.13.5.10.11.10.1
A conceptual row containing the status of the MSTP instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  MstpMapEntry  

mstpMapIndex 1.1.890.1.5.13.5.10.11.10.1.1
Uniquely identifies an instance.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mstpMapVlans1k 1.1.890.1.5.13.5.10.11.10.1.2
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 0 through 1023. The first octet corresponds to VLANs with VlanIndex values 0 through 7; the second octet to VLANs 8 through 15 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstpMapVlans2k 1.1.890.1.5.13.5.10.11.10.1.3
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 1024 through 2047. The first octet corresponds to VLANs with VlanIndex values 1024 through 1031; the second octet to VLANs 1032 through 1039 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstpMapVlans3k 1.1.890.1.5.13.5.10.11.10.1.4
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 2048 through 3071. The first octet corresponds to VLANs with VlanIndex values 2048 through 2055; the second octet to VLANs 2056 through 2063 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstpMapVlans4k 1.1.890.1.5.13.5.10.11.10.1.5
A string of octets containing one bit per VLAN for VLANS with VlanIndex values 3072 through 4095. The first octet corresponds to VLANs with VlanIndex values 3072 through 3079; the second octet to VLANs 3080 through 3087 etc. The most significant bit of each octet corresponds to the lowest VlanIndex value in that octet. For each VLAN that is mapped to this MSTP instance, the bit corresponding to that VLAN is set to '1'.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..128)  

mstpVlanTable 1.1.890.1.5.13.5.10.11.11
This table contains one entry for each VlanId. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MstpVlanEntry

mstpVlanEntry 1.1.890.1.5.13.5.10.11.11.1
Information regarding the instance to which each Vlan is mapped.
Status: current Access: not-accessible
OBJECT-TYPE    
  MstpVlanEntry  

mstpVlanIndex 1.1.890.1.5.13.5.10.11.11.1.1
The VlanId for which this entry contains the instance mapped.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

mstpVlanMstIndex 1.1.890.1.5.13.5.10.11.11.1.2
An integer with values ranging from 0 to 64 that identify a the CIST/MSTI instance to which this VLAN is mapped
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mstpPortTable 1.1.890.1.5.13.5.10.11.12
A table that contains port-specific MSTP information. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MstpPortEntry

mstpPortEntry 1.1.890.1.5.13.5.10.11.12.1
A list of MSTP information maintained by each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  MstpPortEntry  

mstpPortAdminEdgePort 1.1.890.1.5.13.5.10.11.12.1.1
The administrative value of the Edge Port parameter. A value of true(1) indicates that this port should be assumed as an edge-port and a value of false(2) indicates that this port should be assumed as a non-edge-port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

mstpPortAdminPointToPoint 1.1.890.1.5.13.5.10.11.12.1.2
The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of forceFalse(1) indicates that this port should be treated as having a shared media connection. A value of auto(2) indicates that this port is considered to have a point-to-point link if it is an Aggregator and all of its members are aggregatable, or if the MAC entity is configured for full duplex operation, either through auto-negotiation or by management means.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER auto(1), forceTrue(2), forceFalse(3)  

mstpXstTable 1.1.890.1.5.13.5.10.11.13
Bridge priority configuration for multiple spanning trees. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MstpXstEntry

mstpXstEntry 1.1.890.1.5.13.5.10.11.13.1
An entry of mstpXstTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MstpXstEntry  

mstpXstId 1.1.890.1.5.13.5.10.11.13.1.1
Identifies a spanning tree.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mstpXstBridgePriority 1.1.890.1.5.13.5.10.11.13.1.2
Bridge priority, in steps of 4096.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..61440  

mstpXstPortTable 1.1.890.1.5.13.5.10.11.14
Port configuration for multiple spanning trees. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MstpXstPortEntry

mstpXstPortEntry 1.1.890.1.5.13.5.10.11.14.1
An entry of mstpXstPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MstpXstPortEntry  

mstpXstPortXstId 1.1.890.1.5.13.5.10.11.14.1.1
Identifies a spanning tree.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mstpXstPortIndex 1.1.890.1.5.13.5.10.11.14.1.2
The port number of the port for which this entry contains MSTP management information.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mstpXstPortEnable 1.1.890.1.5.13.5.10.11.14.1.3
The enabled/disabled status of the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

mstpXstPortPriority 1.1.890.1.5.13.5.10.11.14.1.4
The value of the priority field which is contained in the first (in network byte order) octet of the (2 octet long) Port ID.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

mstpXstPortAdminPathCost 1.1.890.1.5.13.5.10.11.14.1.5
The contribution of this port to the path cost of paths towards the spanning tree root which include this port. 0 menas it is determined by link speed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..200000000  

vlanIsolationTable 1.1.890.1.5.13.5.10.12.1
A table contains configuration of isolated VLAN. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VlanIsolationEntry

vlanIsolationEntry 1.1.890.1.5.13.5.10.12.1.1
An entry of vlanIsolationTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VlanIsolationEntry  

vlanIsolationRowStatus 1.1.890.1.5.13.5.10.12.1.1.1
Row status of the table used to create/delete an entry.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

macAgingTime 1.1.890.1.5.13.5.10.13.1
The mac aging time in seconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

cfmLoopbackPortTable 1.1.890.1.5.13.5.10.14.1
A table that contains CFM information. This table is supported by R5.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CfmLoopbackPortEntry

cfmLoopbackPortEntry 1.1.890.1.5.13.5.10.14.1.1
An entry in cfmLoopbackPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CfmLoopbackPortEntry  

cfmLoopbackPortState 1.1.890.1.5.13.5.10.14.1.1.1
CFM loopback enable/disable on the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

cfmMIPTable 1.1.890.1.5.13.5.10.14.2
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CfmMIPEntry

cfmMIPEntry 1.1.890.1.5.13.5.10.14.2.1
An entry in cfmMIPTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CfmMIPEntry  

cfmLevel 1.1.890.1.5.13.5.10.14.2.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

cfmVlanID 1.1.890.1.5.13.5.10.14.2.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

cfmPort 1.1.890.1.5.13.5.10.14.2.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

cfmMIPRowStatus 1.1.890.1.5.13.5.10.14.2.1.4
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

cfmMIPMacAddress 1.1.890.1.5.13.5.10.14.2.1.5
MAC address of maintenance domain intermediate point
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

cfmActionEnableStatus 1.1.890.1.5.13.5.10.14.3
CFM Action enable status for the CO device
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

cfmMode 1.1.890.1.5.13.5.10.14.4
The compliant CFM standard
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dot1ag(1), y1731(2)  

cfmMIPRespondMcastLbm 1.1.890.1.5.13.5.10.14.5
The status indicate whether a MIP respond to mulcast lbms or not.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

cfmLoopbackTimeout 1.1.890.1.5.13.5.10.14.6
CFM loopback timeout value.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..86400  

cfmLbrTable 1.1.890.1.5.13.5.10.14.7
This table contains a list of Loopback replies received by a specific MEP in response to a loopback message.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CfmLbrEntry

cfmLbrEntry 1.1.890.1.5.13.5.10.14.7.1
The Loopback Reply table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  CfmLbrEntry  

cfmLbrSeqNumber 1.1.890.1.5.13.5.10.14.7.1.1
Transaction identifier/Sequence number returned by a previous transmit loopback message command, indicating which LBM's response is going to be returned.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..4294967295  

cfmLbrReceiveOrder 1.1.890.1.5.13.5.10.14.7.1.2
An index to distinguish among multiple LBRs with the same LBR Transaction Identifier field value. cfmLbrReceiveOrder are assigned sequentially from 1, in the order that the Loopback Initiator received the LBRs.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..4294967295  

cfmLbrSrcMac 1.1.890.1.5.13.5.10.14.7.1.3
Source MAC address returned in the LBR.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

remoteLoopbackTable 1.1.890.1.5.13.5.10.15.1
A table that contains OAM information. This table is supported by R5.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RemoteLoopbackEntry

remoteLoopbackEntry 1.1.890.1.5.13.5.10.15.1.1
An entry in remoteLoopbackTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  RemoteLoopbackEntry  

remoteLoopbackEnable 1.1.890.1.5.13.5.10.15.1.1.1
OAM remote loopback enable/disable on the port.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

vlanpriorityEnable 1.1.890.1.5.13.5.10.16.1
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

vlanpriorityTable 1.1.890.1.5.13.5.10.16.2
A table that contains VLAN Priority information. This table is supported by R5.04 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VlanpriorityEntry

vlanpriorityEntry 1.1.890.1.5.13.5.10.16.2.1
An entry in vlanpriorityTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VlanpriorityEntry  

vlanpriorityVid 1.1.890.1.5.13.5.10.16.2.1.1
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..4094  

vlanpriorityPri 1.1.890.1.5.13.5.10.16.2.1.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

vlanpriorityRowStatus 1.1.890.1.5.13.5.10.16.2.1.3
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

mirrorEnable 1.1.890.1.5.13.5.10.17.1
set to 'enable' to enable mirroring
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

mirrorMonitorPort 1.1.890.1.5.13.5.10.17.2
monitor port
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

mirrorPortTable 1.1.890.1.5.13.5.10.17.3
This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MirrorPortEntry

mirrorPortEntry 1.1.890.1.5.13.5.10.17.3.1
An entry in mirrorPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MirrorPortEntry  

mirrorPortDirection 1.1.890.1.5.13.5.10.17.3.1.1
Set to 'ingress' to mirror ingress traffic, 'egress' to mirror egress traffic, 'both' to mirror bi-directional traffic, 'none' to disable mirroring in this port
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ingress(1), egress(2), both(3), none(4)  

lldpEnable 1.1.890.1.5.13.5.10.18.1
set to 'enable' to enable lldp
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

sysState 1.1.890.1.5.13.5.11.1
OBJECT IDENTIFIER    

sysOperation 1.1.890.1.5.13.5.11.2
OBJECT IDENTIFIER    

hwMonitor 1.1.890.1.5.13.5.11.3
OBJECT IDENTIFIER    

timeSetup 1.1.890.1.5.13.5.11.4
OBJECT IDENTIFIER    

accessCtrl 1.1.890.1.5.13.5.11.5
OBJECT IDENTIFIER    

syslog 1.1.890.1.5.13.5.11.6
OBJECT IDENTIFIER    

snmp 1.1.890.1.5.13.5.11.7
OBJECT IDENTIFIER    

user 1.1.890.1.5.13.5.11.8
OBJECT IDENTIFIER    

aaa 1.1.890.1.5.13.5.11.9
OBJECT IDENTIFIER    

session 1.1.890.1.5.13.5.11.10
OBJECT IDENTIFIER    

bootimage 1.1.890.1.5.13.5.11.11
OBJECT IDENTIFIER    

systemStatus 1.1.890.1.5.13.5.11.1.1
This variable indicates the alarm status of the module. It is a bit map represented a sum, therefore, it can represent multiple defects simultaneously. The moduleNoDefect should be set if and only if no other flag is set. The various bit positions are: 1 moduleNoDefect 2 moduleOverHeat 3 moduleFanRpmLow 4 moduleVoltageLow 5 moduleThermalSensorFailure 6 modulePullOut 7 powerDC48VAFailure 8 powerDC48VBFailure 9 extAlarmInputTrigger 10 moduleDown 11 mscSwitchOverOK 12 networkTopologyChange 13 macSpoof 14 cpuHigh 15 memoryUsageHigh 16 packetBufferUsageHigh 17 loopguardOccurence
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ledStatus 1.1.890.1.5.13.5.11.1.2
OBJECT IDENTIFIER    

ledAlarmStatus 1.1.890.1.5.13.5.11.1.2.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

chassisStats 1.1.890.1.5.13.5.11.1.3
OBJECT IDENTIFIER    

dcPowerStatus 1.1.890.1.5.13.5.11.1.3.1
This variable indicates the status of DC Power Status. The dcPowerStatus is a bit map represented as a sum, therefore, it can represent multiple defects simultaneously. The various bit positions are: BIT0: POWER Input A BIT1: POWER Input B
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

extAlarmStatus 1.1.890.1.5.13.5.11.1.4
This variable indicates the status of the external alarm. Every bit record one kind of external alarm, and there are totally 4 kind of them. Every bit of the variable will be 0 or 1 only, indicate the alarm is clear or set now.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sysTarget 1.1.890.1.5.13.5.11.2.1
IfIndex of the operation target.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

sysOps 1.1.890.1.5.13.5.11.2.2
The manager sets the corresponding bit value to 1 to start the operation and the agent clears the object to zero when the operation is successfully completed. The various bit positions are: BIT 1: reset
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

sysRebootTime 1.1.890.1.5.13.5.11.2.3
Write a non-zero value to schedule a reboot. Write oo0oo to cancel it. When read, it returns the remaining time to the schedule reboot.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..2147483647  

fanRpmTable 1.1.890.1.5.13.5.11.3.1
A table that contains rpm information about the fans.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FanRpmEntry

fanRpmEntry 1.1.890.1.5.13.5.11.3.1.1
A list of rpm information for each fan.
Status: current Access: not-accessible
OBJECT-TYPE    
  FanRpmEntry  

fanRpmIndex 1.1.890.1.5.13.5.11.3.1.1.1
The identity of the fan.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fanRpmCurValue 1.1.890.1.5.13.5.11.3.1.1.2
The current rpm of the fan.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fanRpmMaxValue 1.1.890.1.5.13.5.11.3.1.1.3
The maximum rpm ever performed by the fan.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fanRpmMinValue 1.1.890.1.5.13.5.11.3.1.1.4
The minimum rpm ever performed by the fan.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

fanRpmLowThresh 1.1.890.1.5.13.5.11.3.1.1.5
The low threshold of the rpm of the fan.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

fanRpmDescr 1.1.890.1.5.13.5.11.3.1.1.6
The description of the fan (e.g. location, function, etc.).
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

fanRpmHighThresh 1.1.890.1.5.13.5.11.3.1.1.7
The high threshold of the rpm of the fan.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voltageTable 1.1.890.1.5.13.5.11.3.2
A table that contains voltage information about the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoltageEntry

voltageEntry 1.1.890.1.5.13.5.11.3.2.1
A list of voltage information for each sensor.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoltageEntry  

voltageIndex 1.1.890.1.5.13.5.11.3.2.1.1
The identity of the sensor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voltageCurValue 1.1.890.1.5.13.5.11.3.2.1.2
The current voltage detected by the sensor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voltageMaxValue 1.1.890.1.5.13.5.11.3.2.1.3
The maximum voltage ever detected by the sensor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voltageMinValue 1.1.890.1.5.13.5.11.3.2.1.4
The minimum voltage ever detected by the sensor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voltageNominalValue 1.1.890.1.5.13.5.11.3.2.1.5
The nominal voltage which the power should supply.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voltageLowThresh 1.1.890.1.5.13.5.11.3.2.1.6
The low threshold of the voltage.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voltageDescr 1.1.890.1.5.13.5.11.3.2.1.7
The description of the voltage (e.g. location, nominal value, etc.).
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voltageHighThresh 1.1.890.1.5.13.5.11.3.2.1.8
The high threshold of the voltage.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

temperatureTable 1.1.890.1.5.13.5.11.3.3
A table that contains temperature information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TemperatureEntry

temperatureEntry 1.1.890.1.5.13.5.11.3.3.1
A list of temperature information for each sensor.
Status: current Access: not-accessible
OBJECT-TYPE    
  TemperatureEntry  

temperatureIndex 1.1.890.1.5.13.5.11.3.3.1.1
The identity of the sensor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

temperatureCurValue 1.1.890.1.5.13.5.11.3.3.1.2
The current temperature detected by the sensor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

temperatureMaxValue 1.1.890.1.5.13.5.11.3.3.1.3
The maximum temperature ever detected by the sensor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

temperatureMinValue 1.1.890.1.5.13.5.11.3.3.1.4
The minimum temperature ever detected by the sensor.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

temperatureHighThresh 1.1.890.1.5.13.5.11.3.3.1.5
The high threshold of the temperature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

temperatureDescr 1.1.890.1.5.13.5.11.3.3.1.6
The description of the temperature sensor (e.g. location, function, etc.).
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

temperatureLowThresh 1.1.890.1.5.13.5.11.3.3.1.7
The low threshold of the temperature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

cpuUtilizationTable 1.1.890.1.5.13.5.11.3.4
A table that contains CPU utilization information. This table is supported by R1.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CpuUtilizationEntry

cpuUtilizationEntry 1.1.890.1.5.13.5.11.3.4.1
An entry of cpuUtilizationTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  CpuUtilizationEntry  

cpuIndex 1.1.890.1.5.13.5.11.3.4.1.1
The identity of the CPU.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

cpuCurValue 1.1.890.1.5.13.5.11.3.4.1.2
The CPU utilization in the past 60 seconds.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

cpuMaxValue 1.1.890.1.5.13.5.11.3.4.1.3
The maximum CPU utilization ever detected.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

cpuHighThresh 1.1.890.1.5.13.5.11.3.4.1.4
The high threshold of CPU usage. If cpuCurValue is larger than the threshold, the device will initiate the eqptCpuHigh trap. This trap is supported by R1.03 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

cpuDescr 1.1.890.1.5.13.5.11.3.4.1.5
The description of the CPU. This trap is supported by R1.03 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

packetBufferUsageTable 1.1.890.1.5.13.5.11.3.5
A table that contains packet buffer usage information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PacketBufferUsageEntry

packetBufferUsageEntry 1.1.890.1.5.13.5.11.3.5.1
An entry of packetBufferUsageTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PacketBufferUsageEntry  

packetBufferIndex 1.1.890.1.5.13.5.11.3.5.1.1
The identity of the packet buffer.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

packetBufferCurValue 1.1.890.1.5.13.5.11.3.5.1.2
The packet buffer usage in the past 60 seconds.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

packetBufferMaxValue 1.1.890.1.5.13.5.11.3.5.1.3
The maximum packet buffer usage ever detected.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

packetBufferHighThresh 1.1.890.1.5.13.5.11.3.5.1.4
The high threshold of packet buffer usage. If packetBufferCurValue is larger than the threshold, the device will initiate the eqptPacketBufferUsageHigh trap.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

packetBufferDescr 1.1.890.1.5.13.5.11.3.5.1.5
The description of the packet buffer.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

memoryUsageTable 1.1.890.1.5.13.5.11.3.6
A table that contains memory usage information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MemoryUsageEntry

memoryUsageEntry 1.1.890.1.5.13.5.11.3.6.1
An entry of memoryUsageTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MemoryUsageEntry  

memoryIndex 1.1.890.1.5.13.5.11.3.6.1.1
The identity of the memory.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

memoryCurValue 1.1.890.1.5.13.5.11.3.6.1.2
The memory usage in the past 60 seconds.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

memoryMaxValue 1.1.890.1.5.13.5.11.3.6.1.3
The maximum memory usage ever detected.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

memoryHighThresh 1.1.890.1.5.13.5.11.3.6.1.4
The high threshold of memory usage. If memoryCurValue is larger than the threshold, the device will initiate the eqptMemoryUsageHigh trap.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

memoryDescr 1.1.890.1.5.13.5.11.3.6.1.5
The description of the memory.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

timeServerMode 1.1.890.1.5.13.5.11.4.1
The mechanism of Time Server when the system boots up.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), daytime(2), time(3), ntp(4)  

timeServerIP 1.1.890.1.5.13.5.11.4.2
The IP Address of Time Server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

systemTime 1.1.890.1.5.13.5.11.4.3
The system time in the format 'HH:MM:SS'.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

systemDate 1.1.890.1.5.13.5.11.4.4
The system date in the format 'YYYY-MM-DD'
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

systemTimeZone 1.1.890.1.5.13.5.11.4.5
The system time zone.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER utc-minus-1200(1), utc-minus-1100(2), utc-minus-1000(3), utc-minus-0900(4), utc-minus-0800(5), utc-minus-0700(6), utc-minus-0600(7), utc-minus-0500(8), utc-minus-0400(9), utc-minus-0300(10), utc-minus-0200(11), utc-minus-0100(12), utc(13), utc-plus-0100(14), utc-plus-0200(15), utc-plus-0300(16), utc-plus-0400(17), utc-plus-0500(18), utc-plus-0600(19), utc-plus-0700(20), utc-plus-0800(21), utc-plus-0900(22), utc-plus-1000(23), utc-plus-1100(24), utc-plus-1200(25), utc-minus-0330(26), utc-plus-0330(27), utc-plus-0430(28), utc-plus-0530(29), utc-plus-0545(30), utc-plus-0630(31), utc-plus-0930(32), utc-plus-1300(33)  

timeServerSync 1.1.890.1.5.13.5.11.4.6
Set the object to 1 to synchronize with the time server.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dayLightSaving 1.1.890.1.5.13.5.11.4.7
OBJECT IDENTIFIER    

dayLightSavingAdminStatus 1.1.890.1.5.13.5.11.4.7.1
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

dayLightSavingStartTime 1.1.890.1.5.13.5.11.4.7.2
OBJECT IDENTIFIER    

dayLightSavingStartMonth 1.1.890.1.5.13.5.11.4.7.2.1
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER jan(1), feb(2), mar(3), apr(4), may(5), jun(6), jul(7), aug(8), sep(9), oct(10), nov(11), dec(12)  

dayLightSavingStartWeek 1.1.890.1.5.13.5.11.4.7.2.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER first(1), second(2), third(3), fourth(4), last(5)  

dayLightSavingStartWday 1.1.890.1.5.13.5.11.4.7.2.3
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER sun(1), mon(2), tus(3), wed(4), thu(5), fri(6), sat(7)  

dayLightSavingStartHour 1.1.890.1.5.13.5.11.4.7.2.4
1: 01:00, 2: 02:00 3: 03:00 4: 04:00 5: 05:00 6: 06:00 7: 07:00 8: 08:00 9: 09:00 10: 10:00 11: 11:00 12: 12:00 13: 13:00 14: 14:00 15: 15:00 16: 16:00 17: 17:00 18: 18:00 19: 19:00 20: 20:00 21: 21:00 22: 22:00 23: 23:00 24: 00:00
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..24  

dayLightSavingEndTime 1.1.890.1.5.13.5.11.4.7.3
OBJECT IDENTIFIER    

dayLightSavingEndMonth 1.1.890.1.5.13.5.11.4.7.3.1
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER jan(1), feb(2), mar(3), apr(4), may(5), jun(6), jul(7), aug(8), sep(9), oct(10), nov(11), dec(12)  

dayLightSavingEndWeek 1.1.890.1.5.13.5.11.4.7.3.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER first(1), second(2), third(3), fourth(4), last(5)  

dayLightSavingEndWday 1.1.890.1.5.13.5.11.4.7.3.3
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER sun(1), mon(2), tus(3), wed(4), thu(5), fri(6), sat(7)  

dayLightSavingEndHour 1.1.890.1.5.13.5.11.4.7.3.4
1: 01:00, 2: 02:00 3: 03:00 4: 04:00 5: 05:00 6: 06:00 7: 07:00 8: 08:00 9: 09:00 10: 10:00 11: 11:00 12: 12:00 13: 13:00 14: 14:00 15: 15:00 16: 16:00 17: 17:00 18: 18:00 19: 19:00 20: 20:00 21: 21:00 22: 22:00 23: 23:00 24: 00:00
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..24  

timeServerInetAddrType 1.1.890.1.5.13.5.11.4.8
The IP Address type.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

timeServerInetAddr 1.1.890.1.5.13.5.11.4.9
The IP Address of Time Server.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

accessCtrlTable 1.1.890.1.5.13.5.11.5.1
A table that contains information about service access control.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AccessCtrlEntry

accessCtrlEntry 1.1.890.1.5.13.5.11.5.1.1
A list of access control entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  AccessCtrlEntry  

accessCtrlService 1.1.890.1.5.13.5.11.5.1.1.1
The service type of the access control entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER telnet(1), ftp(2), web(3), icmp(4), ssh(5), snmp(6), https(7)  

accessCtrlEnable 1.1.890.1.5.13.5.11.5.1.1.2
Enable/disable the service.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

accessCtrlPort 1.1.890.1.5.13.5.11.5.1.1.3
The port number which the service uses.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

securedClientTable 1.1.890.1.5.13.5.11.5.2
A table that contains information about secured clients.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SecuredClientEntry

securedClientEntry 1.1.890.1.5.13.5.11.5.2.1
A list of secured client entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SecuredClientEntry  

securedClientIndex 1.1.890.1.5.13.5.11.5.2.1.1
The index of the entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

securedClientStartIp 1.1.890.1.5.13.5.11.5.2.1.2
The starting IP address of the secured client set.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

securedClientEndIp 1.1.890.1.5.13.5.11.5.2.1.3
The ending IP address of the secured client set.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

securedClientService 1.1.890.1.5.13.5.11.5.2.1.4
Each bit corresponds to a service. The bit is set to 1 if the service is enabled, and set to 0 if the service is disabled. The various bit positions are: BIT 1: telnet BIT 2: ftp BIT 3: web BIT 4: icmp BIT 5: ssh BIT 6: snmp BIT 7: https.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

securedClientEnable 1.1.890.1.5.13.5.11.5.2.1.5
Enable/disable the entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

securedClientInetTable 1.1.890.1.5.13.5.11.5.3
A table that contains information about secured clients.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SecuredClientInetEntry

securedClientInetEntry 1.1.890.1.5.13.5.11.5.3.1
A list of secured client inet entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SecuredClientInetEntry  

securedClientInetIndex 1.1.890.1.5.13.5.11.5.3.1.1
The index of the entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

securedClientInetAddrType 1.1.890.1.5.13.5.11.5.3.1.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

securedClientInetAddr 1.1.890.1.5.13.5.11.5.3.1.3
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

securedClientInetMask 1.1.890.1.5.13.5.11.5.3.1.4
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

securedClientInetService 1.1.890.1.5.13.5.11.5.3.1.5
Each bit corresponds to a service. The bit is set to 1 if the service is enabled, and set to 0 if the service is disabled. The various bit positions are: BIT 1: telnet BIT 2: ftp BIT 3: web BIT 4: icmp BIT 5: ssh BIT 6: snmp BIT 7: https.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

securedClientInetEnable 1.1.890.1.5.13.5.11.5.3.1.6
Enable/disable the entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

syslogEnable 1.1.890.1.5.13.5.11.6.1
Enable/disable syslog function.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

syslogTable 1.1.890.1.5.13.5.11.6.2
A table that contains syslog configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SyslogEntry

syslogEntry 1.1.890.1.5.13.5.11.6.2.1
A list of syslog entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  SyslogEntry  

syslogFacility 1.1.890.1.5.13.5.11.6.2.1.1
Log facility.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER local0(0), local1(1), local2(2), local3(3), local4(4), local5(5), local6(6), local7(7)  

syslogServer 1.1.890.1.5.13.5.11.6.2.1.2
IP address of the syslog server.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

syslogServerInetAddrType 1.1.890.1.5.13.5.11.6.2.1.3
The IP Address type.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

syslogServerInetAddr 1.1.890.1.5.13.5.11.6.2.1.4
IP address of the syslog server.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

trapDestTable 1.1.890.1.5.13.5.11.7.1
A table that contains SNMP trap destination information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TrapDestEntry

trapDestEntry 1.1.890.1.5.13.5.11.7.1.1
The entry of SNMP trap destination table.
Status: current Access: not-accessible
OBJECT-TYPE    
  TrapDestEntry  

trapDestIndex 1.1.890.1.5.13.5.11.7.1.1.1
The index of the entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

trapDestIp 1.1.890.1.5.13.5.11.7.1.1.2
The IP address of the trap destination.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

trapDestPort 1.1.890.1.5.13.5.11.7.1.1.3
The UDP port of the trap destination.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

trapDestSnmpVersion 1.1.890.1.5.13.5.11.7.1.1.4
The SNMP protocol version to send traps.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER v1(1), v2c(2), v3(3)  

trapDestUserName 1.1.890.1.5.13.5.11.7.1.1.5
The user name for sending SNMPv3 traps.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

trapDestInetAddrType 1.1.890.1.5.13.5.11.7.1.1.6
The IP Address type.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

trapDestInetAddr 1.1.890.1.5.13.5.11.7.1.1.7
The IP address of the trap destination.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress  

snmpGetCommunity 1.1.890.1.5.13.5.11.7.2
The SNMP get community.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

snmpSetCommunity 1.1.890.1.5.13.5.11.7.3
The SNMP set community.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

snmpTrapCommunity 1.1.890.1.5.13.5.11.7.4
The SNMP trap community.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

snmpUserTable 1.1.890.1.5.13.5.11.7.5
A table that contains SNMPv3 user information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SnmpUserEntry

snmpUserEntry 1.1.890.1.5.13.5.11.7.5.1
An entry of snmpUserTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SnmpUserEntry  

snmpUserName 1.1.890.1.5.13.5.11.7.5.1.1
The user name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

snmpUserSecurityLevel 1.1.890.1.5.13.5.11.7.5.1.2
The level of security at which SNMP messages can be sent or with which operations are being processed.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noAuthNoPriv(1), authNoPriv(2), authPriv(3)  

snmpUserAuthProtocol 1.1.890.1.5.13.5.11.7.5.1.3
The type of authentication protocol to be used.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER md5(1), sha(2)  

snmpUserPrivProtocol 1.1.890.1.5.13.5.11.7.5.1.4
The type of privacy protocol to be used.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER des(1), aes(2)  

snmpVersion 1.1.890.1.5.13.5.11.7.6
The SNMP version to be used. v3v2c means that the manager can get/set by SNMPv3 and can get by SNMPv2c.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER v2c(1), v3(2), v3v2c(3)  

userTable 1.1.890.1.5.13.5.11.8.5
A table that contains user information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UserEntry

userEntry 1.1.890.1.5.13.5.11.8.5.1
An entry of userTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  UserEntry  

userName 1.1.890.1.5.13.5.11.8.5.1.1
The user name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

userPassword 1.1.890.1.5.13.5.11.8.5.1.2
The user password.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

userPriviledge 1.1.890.1.5.13.5.11.8.5.1.3
The user privilege to decide what operation the user can and cannot do.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..14  

userRowStatus 1.1.890.1.5.13.5.11.8.5.1.4
The row status used to create or delete a user.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

auth 1.1.890.1.5.13.5.11.9.1
OBJECT IDENTIFIER    

acct 1.1.890.1.5.13.5.11.9.2
OBJECT IDENTIFIER    

radius 1.1.890.1.5.13.5.11.9.3
OBJECT IDENTIFIER    

tacacsplus 1.1.890.1.5.13.5.11.9.4
OBJECT IDENTIFIER    

author 1.1.890.1.5.13.5.11.9.5
OBJECT IDENTIFIER    

loginMethod1 1.1.890.1.5.13.5.11.9.1.1
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER local(1), radius(2), tacacsplus(3)  

loginMethod2 1.1.890.1.5.13.5.11.9.1.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), local(1), radius(2), tacacsplus(3)  

loginMethod3 1.1.890.1.5.13.5.11.9.1.3
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), local(1), radius(2), tacacsplus(3)  

enableMethod1 1.1.890.1.5.13.5.11.9.1.4
The first method of enable authentication. This MIB object is supported by R5.06 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), tacacsplus(2)  

enableMethod2 1.1.890.1.5.13.5.11.9.1.5
The second method of enable authentication. This MIB object is supported by R5.06 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), enable(1), tacacsplus(2)  

loginTryCont 1.1.890.1.5.13.5.11.9.1.6
Set to '1' so that the system try next login method only when previous method is not available. Set to '2' so that the system will try next login method when previous method does not authenticate the user.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER off(1), on(2)  

systemActive 1.1.890.1.5.13.5.11.9.2.1
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

systemMethod 1.1.890.1.5.13.5.11.9.2.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER radius(1), tacacsplus(2)  

systemBroadcast 1.1.890.1.5.13.5.11.9.2.3
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

execActive 1.1.890.1.5.13.5.11.9.2.4
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

execMethod 1.1.890.1.5.13.5.11.9.2.5
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER radius(1), tacacsplus(2)  

execMode 1.1.890.1.5.13.5.11.9.2.6
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER start-stop(1), stop-only(2)  

execBroadcast 1.1.890.1.5.13.5.11.9.2.7
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

commandsActive 1.1.890.1.5.13.5.11.9.2.8
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

commandsPrivilege 1.1.890.1.5.13.5.11.9.2.9
1~14
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..14  

commandsBroadcast 1.1.890.1.5.13.5.11.9.2.10
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

updatePeriod 1.1.890.1.5.13.5.11.9.2.11
1~2147483647 minutes
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..2147483647  

radiusAuth 1.1.890.1.5.13.5.11.9.3.1
OBJECT IDENTIFIER    

radiusAcct 1.1.890.1.5.13.5.11.9.3.2
OBJECT IDENTIFIER    

radiusAuthRedundantMode 1.1.890.1.5.13.5.11.9.3.1.1
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER index-priority(1), round-robin(2)  

radiusAuthTimeoutPeriod 1.1.890.1.5.13.5.11.9.3.1.2
1~1000 seconds
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..1000  

radiusAuthServerTable 1.1.890.1.5.13.5.11.9.3.1.3
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RadiusAuthServerEntry

radiusAuthServerEntry 1.1.890.1.5.13.5.11.9.3.1.3.1
An entry of radiusAuthServerTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  RadiusAuthServerEntry  

radiusAuthServerIndex 1.1.890.1.5.13.5.11.9.3.1.3.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

radiusAuthServerIP 1.1.890.1.5.13.5.11.9.3.1.3.1.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

radiusAuthServerPort 1.1.890.1.5.13.5.11.9.3.1.3.1.3
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

radiusAuthServerSecret 1.1.890.1.5.13.5.11.9.3.1.3.1.4
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

radiusAcctTimeoutPeriod 1.1.890.1.5.13.5.11.9.3.2.1
1~1000 seconds
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..1000  

radiusAcctServerTable 1.1.890.1.5.13.5.11.9.3.2.2
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RadiusAcctServerEntry

radiusAcctServerEntry 1.1.890.1.5.13.5.11.9.3.2.2.1
An entry of radiusAcctServerTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  RadiusAcctServerEntry  

radiusAcctServerIndex 1.1.890.1.5.13.5.11.9.3.2.2.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

radiusAcctServerIP 1.1.890.1.5.13.5.11.9.3.2.2.1.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

radiusAcctServerPort 1.1.890.1.5.13.5.11.9.3.2.2.1.3
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

radiusAcctServerSecret 1.1.890.1.5.13.5.11.9.3.2.2.1.4
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

radiusAcctRedundantMode 1.1.890.1.5.13.5.11.9.3.2.3
Redundant mode of accounting via RADIUS. This MIB object is supported by R5.06 and later versions
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER index-priority(1), round-robin(2)  

tacacsplusAuth 1.1.890.1.5.13.5.11.9.4.1
OBJECT IDENTIFIER    

tacacsplusAcct 1.1.890.1.5.13.5.11.9.4.2
OBJECT IDENTIFIER    

tacacsplusAuthor 1.1.890.1.5.13.5.11.9.4.3
OBJECT IDENTIFIER    

tacacsplusAuthRedundantMode 1.1.890.1.5.13.5.11.9.4.1.1
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER index-priority(1), round-robin(2)  

tacacsplusAuthTimeoutPeriod 1.1.890.1.5.13.5.11.9.4.1.2
1~1000 seconds
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..1000  

tacacsplusAuthServerTable 1.1.890.1.5.13.5.11.9.4.1.3
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TacacsplusAuthServerEntry

tacacsplusAuthServerEntry 1.1.890.1.5.13.5.11.9.4.1.3.1
An entry of tacacsplusAuthServerTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  TacacsplusAuthServerEntry  

tacscsplusAuthServerIndex 1.1.890.1.5.13.5.11.9.4.1.3.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

tacscsplusAuthServerIP 1.1.890.1.5.13.5.11.9.4.1.3.1.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

tacscsplusAuthServerPort 1.1.890.1.5.13.5.11.9.4.1.3.1.3
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tacscsplusAuthServerSecret 1.1.890.1.5.13.5.11.9.4.1.3.1.4
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

tacacsplusAcctTimeoutPeriod 1.1.890.1.5.13.5.11.9.4.2.1
1~1000 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..1000  

tacacsplusAcctServerTable 1.1.890.1.5.13.5.11.9.4.2.2
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TacacsplusAcctServerEntry

tacacsplusAcctServerEntry 1.1.890.1.5.13.5.11.9.4.2.2.1
An entry of tacacsplusAcctServerTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  TacacsplusAcctServerEntry  

tacacsplusAcctServerIndex 1.1.890.1.5.13.5.11.9.4.2.2.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

tacacsplusAcctServerIP 1.1.890.1.5.13.5.11.9.4.2.2.1.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

tacacsplusAcctServerPort 1.1.890.1.5.13.5.11.9.4.2.2.1.3
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tacacsplusAcctServerSecret 1.1.890.1.5.13.5.11.9.4.2.2.1.4
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

tacacsplusAcctRedundantMode 1.1.890.1.5.13.5.11.9.4.2.3
Redundant mode of accounting via TACACS+. This MIB object is supported by R5.06 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER index-priority(1), round-robin(2)  

tacacsplusAuthorRedundantMode 1.1.890.1.5.13.5.11.9.4.3.1
Redundant mode of command authorization via TACACS+ This MIB Object is supported by R5.06 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER index-priority(1), round-robin(2)  

tacacsplusAuthorTimeoutPeriod 1.1.890.1.5.13.5.11.9.4.3.2
Timeout period (second) of command authorization via TACACS+. 1~1000 seconds This MIB Object is supported by R5.06 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..1000  

tacacsplusAuthorServerTable 1.1.890.1.5.13.5.11.9.4.3.3
This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TacacsplusAuthorServerEntry

tacacsplusAuthorServerEntry 1.1.890.1.5.13.5.11.9.4.3.3.1
An entry of tacacsplusAuthorServerEntry. This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  TacacsplusAuthorServerEntry  

tacscsplusAuthorServerIndex 1.1.890.1.5.13.5.11.9.4.3.3.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

tacscsplusAuthorServerIP 1.1.890.1.5.13.5.11.9.4.3.3.1.2
TACACS+ server IP for command authorization.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

tacscsplusAuthorServerPort 1.1.890.1.5.13.5.11.9.4.3.3.1.3
TACACS+ server port for command authorization.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

tacscsplusAuthorServerSecret 1.1.890.1.5.13.5.11.9.4.3.3.1.4
TACACS+ server secret key for command authorization.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

authorCmdMethodTable 1.1.890.1.5.13.5.11.9.5.1
This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AuthorCmdMethodEntry

authorCmdMethodEntry 1.1.890.1.5.13.5.11.9.5.1.1
An entry of authorCmdMethodEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  AuthorCmdMethodEntry  

authorCmdMethod 1.1.890.1.5.13.5.11.9.5.1.1.1
Method mode of command authorization in each privilege level.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(1), local(2), tacacsPlus(3), tacacsPlus-then-none(4), tacacsPlus-then-local(5)  

authorExec 1.1.890.1.5.13.5.11.9.5.2
enable: 1. User login via Web GUI: 1.1. Tacacs+ account with privilege 14, get the privilege as 14. 1.2. Tacacs+ account with privilege lower than 14, get the privilege as 1. 2. User login via SSH, telnet or console: 1.1. Whether Tacacs+ account privilege is (1-14), get the same privilege as Tacacs+ server. disable: 1. Whether user login via SSH, telnet, web GUI or console, get the privilege as 1. (no matter what the Tacacs+ account privilege is)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sessionTimeOut 1.1.890.1.5.13.5.11.10.1
Configurable Web, telnet and SSH session timeout.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

sessionLoginMessage 1.1.890.1.5.13.5.11.10.2
Login message in 128 characters.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

sysBootImage 1.1.890.1.5.13.5.11.11.1
Boot from the first image or the second image.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER image1(1), image2(2)  

dhcpStats 1.1.890.1.5.13.5.13.1
OBJECT IDENTIFIER    

igmpStats 1.1.890.1.5.13.5.13.2
OBJECT IDENTIFIER    

macStats 1.1.890.1.5.13.5.13.3
OBJECT IDENTIFIER    

adslStats 1.1.890.1.5.13.5.13.4
OBJECT IDENTIFIER    

shdslStats 1.1.890.1.5.13.5.13.5
OBJECT IDENTIFIER    

ipStats 1.1.890.1.5.13.5.13.6
OBJECT IDENTIFIER    

mstpStats 1.1.890.1.5.13.5.13.7
OBJECT IDENTIFIER    

vdslStats 1.1.890.1.5.13.5.13.8
OBJECT IDENTIFIER    

paepvcStats 1.1.890.1.5.13.5.13.9
OBJECT IDENTIFIER    

vlanMacStats 1.1.890.1.5.13.5.13.10
OBJECT IDENTIFIER    

ipbpvcStats 1.1.890.1.5.13.5.13.11
OBJECT IDENTIFIER    

voipStats 1.1.890.1.5.13.5.13.12
OBJECT IDENTIFIER    

enetStats 1.1.890.1.5.13.5.13.13
OBJECT IDENTIFIER    

ifStats 1.1.890.1.5.13.5.13.14
OBJECT IDENTIFIER    

imaStats 1.1.890.1.5.13.5.13.15
OBJECT IDENTIFIER    

e1Stats 1.1.890.1.5.13.5.13.16
OBJECT IDENTIFIER    

loopguardStats 1.1.890.1.5.13.5.13.18
OBJECT IDENTIFIER    

stpStats 1.1.890.1.5.13.5.13.19
OBJECT IDENTIFIER    

gbondStats 1.1.890.1.5.13.5.13.20
OBJECT IDENTIFIER    

vdsl2Stats 1.1.890.1.5.13.5.13.21
OBJECT IDENTIFIER    

mldStats 1.1.890.1.5.13.5.13.22
OBJECT IDENTIFIER    

macFFStats 1.1.890.1.5.13.5.13.23
OBJECT IDENTIFIER    

imageStats 1.1.890.1.5.13.5.13.24
OBJECT IDENTIFIER    

dhcpSnoopIpTable 1.1.890.1.5.13.5.13.1.1
This table shows the IP addresses and netmasks offered by the DHCP server. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpSnoopIpEntry

dhcpSnoopIpEntry 1.1.890.1.5.13.5.13.1.1.1
An entry of dhcpSnoopIpTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpSnoopIpEntry  

dhcpSnoopIp 1.1.890.1.5.13.5.13.1.1.1.1
The snooped IP address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

dhcpSnoopMac 1.1.890.1.5.13.5.13.1.1.1.2
The snooped MAC address.
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

dhcpSnoopVid 1.1.890.1.5.13.5.13.1.1.1.3
The snooped VLAN ID.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

dhcpSnoopCounterTable 1.1.890.1.5.13.5.13.1.2
This table shows the DHCP statistics. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DhcpSnoopCounterEntry

dhcpSnoopCounterEntry 1.1.890.1.5.13.5.13.1.2.1
An entry of dhcpSnoopCounterTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  DhcpSnoopCounterEntry  

dhcpDiscovery 1.1.890.1.5.13.5.13.1.2.1.1
The total number of received DHCP server discovery packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dhcpOffer 1.1.890.1.5.13.5.13.1.2.1.2
The total number of received DHCP server offer packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dhcpRequest 1.1.890.1.5.13.5.13.1.2.1.3
The total number of received DHCP IP request packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dhcpAck 1.1.890.1.5.13.5.13.1.2.1.4
The total number of received DHCP IP acknowledge packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dhcpAckBySnoopFull 1.1.890.1.5.13.5.13.1.2.1.5
The total number of received DHCP IP acknowledge packets that replace the oldest snooping entry in snooping table due to table full.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dhcpv6Solicit 1.1.890.1.5.13.5.13.1.2.1.6
The total number of received DHCPv6 solicit packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dhcpv6Advertise 1.1.890.1.5.13.5.13.1.2.1.7
The total number of received DHCPv6 advertise packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dhcpv6Request 1.1.890.1.5.13.5.13.1.2.1.8
The total number of received DHCPv6 request packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dhcpv6Reply 1.1.890.1.5.13.5.13.1.2.1.9
The total number of received DHCPv6 reply packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dhcpv6Renew 1.1.890.1.5.13.5.13.1.2.1.10
The total number of received DHCPv6 renew packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dhcpv6Rebind 1.1.890.1.5.13.5.13.1.2.1.11
The total number of received DHCPv6 rebind packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dhcpv6Release 1.1.890.1.5.13.5.13.1.2.1.12
The total number of received DHCPv6 release packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dhcpv6RelayFwd 1.1.890.1.5.13.5.13.1.2.1.13
The total number of received DHCPv6 relay-forward packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dhcpv6RelayReply 1.1.890.1.5.13.5.13.1.2.1.14
The total number of received DHCPv6 relay-reply packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

dhcpv6SnoopIpTable 1.1.890.1.5.13.5.13.1.3
This table shows LDRA statistics.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Dhcpv6SnoopIpEntry

dhcpv6SnoopIpEntry 1.1.890.1.5.13.5.13.1.3.1
An entry of dhcpv6SnoopIpTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Dhcpv6SnoopIpEntry  

dhcpv6SnoopInetAddrType 1.1.890.1.5.13.5.13.1.3.1.1
The snooped IP address type.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

dhcpv6SnoopInetAddr 1.1.890.1.5.13.5.13.1.3.1.2
The snooped IP address.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

dhcpv6SnoopMac 1.1.890.1.5.13.5.13.1.3.1.3
The snooped MAC address.
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

dhcpv6SnoopVid 1.1.890.1.5.13.5.13.1.3.1.4
The snooped VLAN ID.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

igmpQueryCntTotal 1.1.890.1.5.13.5.13.2.1
The total number of IGMP query messages received. This object is supported by R1.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpReportCntTotal 1.1.890.1.5.13.5.13.2.2
The total number of IGMP report messages received. This object is supported by R1.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpLeaveCntTotal 1.1.890.1.5.13.5.13.2.3
The total number of IGMP leave messages received. This object is supported by R1.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpNumOfActiveGroups 1.1.890.1.5.13.5.13.2.4
The total number of IGMP learned groups. This object is supported by R1.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

igmpGroupTable 1.1.890.1.5.13.5.13.2.5
A table that displays IGMP learned group member information. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpGroupEntry

igmpGroupEntry 1.1.890.1.5.13.5.13.2.5.1
An entry of igmpGroupTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpGroupEntry  

igmpGroupVid 1.1.890.1.5.13.5.13.2.5.1.1
The IGMP group VLAN ID.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

igmpGroupIp 1.1.890.1.5.13.5.13.2.5.1.2
The multicast IP address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

igmpGroupNumOfMembers 1.1.890.1.5.13.5.13.2.5.1.3
The number of member ports in the group.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

igmpGroupMemberPorts 1.1.890.1.5.13.5.13.2.5.1.4
The member port list of the group.
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

igmpGroupPortTable 1.1.890.1.5.13.5.13.2.6
A table that displays IGMP joined groups in this port. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpGroupPortEntry

igmpGroupPortEntry 1.1.890.1.5.13.5.13.2.6.1
An entry of igmpGroupPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpGroupPortEntry  

igmpGroupPortVid 1.1.890.1.5.13.5.13.2.6.1.1
The IGMP group VLAN ID.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

igmpGroupPortIp 1.1.890.1.5.13.5.13.2.6.1.2
The multicast IP address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

igmpGroupPortSourceIp 1.1.890.1.5.13.5.13.2.6.1.3
The source IP address that joins the IGMP group.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

igmpPortCtrlPduTable 1.1.890.1.5.13.5.13.2.7
A table that displays IGMP related counter values in this port. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpPortCtrlPduEntry

igmpPortCtrlPduEntry 1.1.890.1.5.13.5.13.2.7.1
An entry of igmpPortCtrlPduTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpPortCtrlPduEntry  

igmpPortCtrlPduQueryCnt 1.1.890.1.5.13.5.13.2.7.1.1
The total number of IGMP query messages received in this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpPortCtrlPduReportCnt 1.1.890.1.5.13.5.13.2.7.1.2
The total number of IGMP report messages received in this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpPortCtrlPduLeaveCnt 1.1.890.1.5.13.5.13.2.7.1.3
The total number of IGMP leave messages received in this port.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpPortNumOfActiveGroups 1.1.890.1.5.13.5.13.2.7.1.4
The total number of active IGMP groups in this port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

igmpPortCtrlPduV2SuccessJoinCnt 1.1.890.1.5.13.5.13.2.7.1.5
The total number of IGMP V2 success joins in this port. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpPortCtrlPduV2UnsuccJoinCnt 1.1.890.1.5.13.5.13.2.7.1.6
The total number of IGMP V2 unsuccess joins in this port. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpPortCtrlPduGenQryCnt 1.1.890.1.5.13.5.13.2.7.1.7
The total number of IGMP general queries in this port. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpPortCtrlPduSpecQryCnt 1.1.890.1.5.13.5.13.2.7.1.8
The total number of IGMP specific queries in this port. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpPortCtrlPduV3SuccessReportCnt 1.1.890.1.5.13.5.13.2.7.1.9
The total number of IGMP V3 success joins in this port. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpPortCtrlPduV3UnsuccReportCnt 1.1.890.1.5.13.5.13.2.7.1.10
The total number of IGMP V3 unsuccess joins in this port. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpPortCtrlPduInvalidCnt 1.1.890.1.5.13.5.13.2.7.1.11
The total number of IGMP invalid in this port. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpVlanStatsTable 1.1.890.1.5.13.5.13.2.8
A table that displays IGMP related counter values per VLAN.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IgmpVlanStatsEntry

igmpVlanStatsEntry 1.1.890.1.5.13.5.13.2.8.1
An entry of igmpVlanStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IgmpVlanStatsEntry  

igmpVlanStatsVlanIndex 1.1.890.1.5.13.5.13.2.8.1.1
VLAN ID.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

igmpVlanStatsQueryCnt 1.1.890.1.5.13.5.13.2.8.1.2
The total number of IGMP query messages received in this VLAN.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpVlanStatsReportCnt 1.1.890.1.5.13.5.13.2.8.1.3
The total number of IGMP report messages received in this VLAN.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpVlanStatsLeaveCnt 1.1.890.1.5.13.5.13.2.8.1.4
The total number of IGMP leave messages received in this VLAN.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpVlanStatsNumOfActiveGroups 1.1.890.1.5.13.5.13.2.8.1.5
The total number of active IGMP groups in this VLAN.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

igmpVlanStatsQueryPort 1.1.890.1.5.13.5.13.2.8.1.6
The received Port of IGMP Router
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

igmpVlanStatsQuerierIp 1.1.890.1.5.13.5.13.2.8.1.7
The IP address of IGMP Router
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

igmpVlanStatsUnsuccessReportCnt 1.1.890.1.5.13.5.13.2.8.1.8
Total number of successful joins from users. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpVlanStatsSuccessReportCnt 1.1.890.1.5.13.5.13.2.8.1.9
Total number of unsuccessful joins from users. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpVlanStatsGeneralQueryInCnt 1.1.890.1.5.13.5.13.2.8.1.10
Total number of general queries sent to users. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpVlanStatsGeneralQueryOutCnt 1.1.890.1.5.13.5.13.2.8.1.11
Total number of general queries received from network. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpVlanStatsSpecificQueryInCnt 1.1.890.1.5.13.5.13.2.8.1.12
Total number of specific queries sent to users. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpVlanStatsSpecificQueryOutCnt 1.1.890.1.5.13.5.13.2.8.1.13
Total number of specific queries received from network. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpQueryOutCnt 1.1.890.1.5.13.5.13.2.9
The total number of IGMP query messages transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpReportOutCnt 1.1.890.1.5.13.5.13.2.10
The total number of IGMP report messages transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpLeaveOutCnt 1.1.890.1.5.13.5.13.2.11
The total number of IGMP leave messages transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpQueryDropCnt 1.1.890.1.5.13.5.13.2.12
The total number of IGMP query messages dropped.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpReportDropCnt 1.1.890.1.5.13.5.13.2.13
The total number of IGMP report messages dropped.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

igmpLeaveDropCnt 1.1.890.1.5.13.5.13.2.14
The total number of IGMP leave messages dropped.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

macDisplayTarget 1.1.890.1.5.13.5.13.3.1
This managed object is a filter used for identify the target from which the MAC addresses are learned in macTable. Ifindex is used to specify a specific interface of which the MAC addresses are displayed. Some values are reserved for special purpose, they are: 0: All interfaces 50: All uplink ports
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

macTable 1.1.890.1.5.13.5.13.3.2
A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacEntry

macEntry 1.1.890.1.5.13.5.13.3.2.1
An entry of macTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacEntry  

macAddress 1.1.890.1.5.13.5.13.3.2.1.1
A unicast MAC address for which the bridge has forwarding and/or filtering information.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

macPort 1.1.890.1.5.13.5.13.3.2.1.2
The port from which the mac address has been learned.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macStatus 1.1.890.1.5.13.5.13.3.2.1.3
The status of this entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), invalid(2), learned(3), self(4), mgmt(5)  

macFlush 1.1.890.1.5.13.5.13.3.3
Set the object to 1 to flush mac table.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

adslLineStatsAtucNumOfSubcarriersPerPort 1.1.890.1.5.13.5.13.4.1
The number of subcarriers per port for ATU-C.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

adslLineStatsAturNumOfSubcarriersPerPort 1.1.890.1.5.13.5.13.4.2
The number of subcarriers per port for ATU-R.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

adslLineStatsTable 1.1.890.1.5.13.5.13.4.3
The table displays ADSL line subcarrier status. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdslLineStatsEntry

adslLineStatsEntry 1.1.890.1.5.13.5.13.4.3.1
An entry of adslLineStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AdslLineStatsEntry  

adslLineStatsAtucHlog1 1.1.890.1.5.13.5.13.4.3.1.1
The object provides Hlog for the ATU-C first 256 subcarriers. Each subcarrier takes two octets to store the value. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslLineStatsAtucHlog2 1.1.890.1.5.13.5.13.4.3.1.2
The object provides Hlog for the ATU-C last 256 subcarriers. Each subcarrier takes two octets to store the value. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslLineStatsAturHlog 1.1.890.1.5.13.5.13.4.3.1.3
The object provides Hlog for the ATU-R subcarriers. Each subcarrier takes two octets to store the value. A special value -32768 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslLineStatsAtucQln1 1.1.890.1.5.13.5.13.4.3.1.4
The object provides QLN for the ATU-C first 256 subcarriers. Each subcarrier takes two octets to store the value. A special value 0 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslLineStatsAtucQln2 1.1.890.1.5.13.5.13.4.3.1.5
The object provides QLN for the ATU-C last 256 subcarriers. Each subcarrier takes two octets to store the value. A special value 0 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslLineStatsAturQln 1.1.890.1.5.13.5.13.4.3.1.6
The object provides QLN for the ATU-R subcarriers. Each subcarrier takes two octets to store the value. A special value 0 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslLineStatsAtucTssi1 1.1.890.1.5.13.5.13.4.3.1.7
The object provides TSSI for the ATU-C first 256 subcarriers. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslLineStatsAtucTssi2 1.1.890.1.5.13.5.13.4.3.1.8
The object provides TSSI for the ATU-C last 256 subcarriers. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslLineStatsAturTssi 1.1.890.1.5.13.5.13.4.3.1.9
The object provides TSSI for the ATU-R subcarriers. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslLineStatsAtucGain1 1.1.890.1.5.13.5.13.4.3.1.10
The object provides GAIN for the ATU-C first 256 subcarriers. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslLineStatsAtucGain2 1.1.890.1.5.13.5.13.4.3.1.11
The object provides GAIN for the ATU-C last 256 subcarriers. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslLineStatsAturGain 1.1.890.1.5.13.5.13.4.3.1.12
The object provides GAIN for the ATU-R subcarriers. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslLineStatsAtucBits1 1.1.890.1.5.13.5.13.4.3.1.13
The object provides BITS for the ATU-C first 256 subcarriers. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslLineStatsAtucBits2 1.1.890.1.5.13.5.13.4.3.1.14
The object provides BITS for the ATU-C last 256 subcarriers. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslLineStatsAturBits 1.1.890.1.5.13.5.13.4.3.1.15
The object provides BITS for the ATU-R subcarriers. Each subcarrier takes two octets to store the value.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

adslLinePerfTable 1.1.890.1.5.13.5.13.4.4
The table displays ADSL line performance.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    AdslLinePerfEntry

adslLinePerfEntry 1.1.890.1.5.13.5.13.4.4.1
An entry of adslLinePerfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  AdslLinePerfEntry  

adslLinePerfAtucCrcFast 1.1.890.1.5.13.5.13.4.4.1.1
The total number of CRC errors in fast mode.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslLinePerfAturCrcFast 1.1.890.1.5.13.5.13.4.4.1.2
The total number of CRC errors in fast mode.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslLinePerfAtucFecFast 1.1.890.1.5.13.5.13.4.4.1.3
The total number of FEC errors in fast mode.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslLinePerfAturFecFast 1.1.890.1.5.13.5.13.4.4.1.4
The total number of FEC errors in fast mode.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslLinePerfAtucCrcInterleave 1.1.890.1.5.13.5.13.4.4.1.5
The total number of CRC errors in interleave mode.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslLinePerfAturCrcInterleave 1.1.890.1.5.13.5.13.4.4.1.6
The total number of CRC errors in interleave mode.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslLinePerfAtucFecInterleave 1.1.890.1.5.13.5.13.4.4.1.7
The total number of FEC errors in interleave mode.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslLinePerfAturFecInterleave 1.1.890.1.5.13.5.13.4.4.1.8
The total number of FEC errors in interleave mode.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslLinePerfAtucEs 1.1.890.1.5.13.5.13.4.4.1.9
Count of the number of Errored Seconds since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslLinePerfAturEs 1.1.890.1.5.13.5.13.4.4.1.10
Count of the number of Errored Seconds since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslLinePerfAtucSes 1.1.890.1.5.13.5.13.4.4.1.11
Count of the number of Severely Errored Seconds since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslLinePerfAturSes 1.1.890.1.5.13.5.13.4.4.1.12
Count of the number of Severely Errored Seconds since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslLinePerfAtucUas 1.1.890.1.5.13.5.13.4.4.1.13
Count of the number of Unavailable Seconds since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslLinePerfAturUas 1.1.890.1.5.13.5.13.4.4.1.14
Count of the number of Unavailable Seconds since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslLinePerfAtucLofs 1.1.890.1.5.13.5.13.4.4.1.15
Count of the number of Loss of Framing failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslLinePerfAturLofs 1.1.890.1.5.13.5.13.4.4.1.16
Count of the number of Loss of Framing failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslLinePerfAtucLoss 1.1.890.1.5.13.5.13.4.4.1.17
Count of the number of Loss of Signal failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslLinePerfAturLoss 1.1.890.1.5.13.5.13.4.4.1.18
Count of the number of Loss of Signal failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslLinePerfAtucLprs 1.1.890.1.5.13.5.13.4.4.1.19
Count of the number of Loss of Power failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

adslLinePerfAturLprs 1.1.890.1.5.13.5.13.4.4.1.20
Count of the number of Loss of Power failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

shdslLinePerfTable 1.1.890.1.5.13.5.13.5.1
The table displays SHDSL line performance.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ShdslLinePerfEntry

shdslLinePerfEntry 1.1.890.1.5.13.5.13.5.1.1
An entry of shdslLinePerfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ShdslLinePerfEntry  

shdslLinePerfEs 1.1.890.1.5.13.5.13.5.1.1.1
Count of Errored Seconds (ES) on this endpoint since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

shdslLinePerfSes 1.1.890.1.5.13.5.13.5.1.1.2
Count of Severely Errored Seconds (SES) on this endpoint since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

shdslLinePerfCrc 1.1.890.1.5.13.5.13.5.1.1.3
Count of CRC anomalies on this endpoint since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

shdslLinePerfLosws 1.1.890.1.5.13.5.13.5.1.1.4
Count of Loss of Sync Word (LOSW) Seconds on this endpoint since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

shdslLinePerfUas 1.1.890.1.5.13.5.13.5.1.1.5
Count of Unavailable Seconds (UAS) on this endpoint since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

shdslLinePerfSegmentAnomalies 1.1.890.1.5.13.5.13.5.1.1.6
Count of Segment Anomalies on this endpoint since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

shdslLinePerfSegmentDefect 1.1.890.1.5.13.5.13.5.1.1.7
Count of Segment Defects on this endpoint since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

shdslPerfCurrTable 1.1.890.1.5.13.5.13.5.2
The table displays SHDSL current performance. This table is supported by R5.05 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ShdslPerfCurrEntry

shdslPerfCurrEntry 1.1.890.1.5.13.5.13.5.2.1
An entry of shdslPerfCurrTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ShdslPerfCurrEntry  

shdslPerfCurrSturLPR 1.1.890.1.5.13.5.13.5.2.1.1
Count of the number of Loss of Power failures since agent reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ipInterfaceTable 1.1.890.1.5.13.5.13.6.1
The table displays IP interface statistics.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpInterfaceEntry

ipInterfaceEntry 1.1.890.1.5.13.5.13.6.1.1
An entry of ipInterfaceTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpInterfaceEntry  

ipInterface 1.1.890.1.5.13.5.13.6.1.1.1
The IP inband/outband interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipAddress 1.1.890.1.5.13.5.13.6.1.1.2
IP address of the interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

ipNetmask 1.1.890.1.5.13.5.13.6.1.1.3
Netmask of the interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

ipBroadcast 1.1.890.1.5.13.5.13.6.1.1.4
Broadcast address of the interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

ipMtu 1.1.890.1.5.13.5.13.6.1.1.5
The size of the largest datagram which can be sent/received on the interface, specified in octets.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipVid 1.1.890.1.5.13.5.13.6.1.1.6
Management VLAN ID of the interface.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

ipInOctet 1.1.890.1.5.13.5.13.6.1.1.7
The total number of octets received on the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ipInUnicast 1.1.890.1.5.13.5.13.6.1.1.8
The number of subnetwork-unicast packets delivered to a higher-layer protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ipInMulticast 1.1.890.1.5.13.5.13.6.1.1.9
The number of subnetwork-multicast packets delivered to a higher-layer protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ipInDiscard 1.1.890.1.5.13.5.13.6.1.1.10
The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ipInError 1.1.890.1.5.13.5.13.6.1.1.11
The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ipInUnknown 1.1.890.1.5.13.5.13.6.1.1.12
The number of packets received via the interface which were discarded because of an unknown or unsupported protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ipOutOctet 1.1.890.1.5.13.5.13.6.1.1.13
The total number of octets transmitted out of the interface.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ipOutUnicast 1.1.890.1.5.13.5.13.6.1.1.14
The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ipOutMulticast 1.1.890.1.5.13.5.13.6.1.1.15
The total number of packets that higher-level protocols requested be transmitted to a subnetwork-multicast address, including those that were discarded or not sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ipOutDiscard 1.1.890.1.5.13.5.13.6.1.1.16
The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ipOutError 1.1.890.1.5.13.5.13.6.1.1.17
The number of outbound packets that could not be transmitted because of errors.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mstpExternalRootId 1.1.890.1.5.13.5.13.7.1
The bridge identifier of the root of the spanning tree as determined by the Spanning Tree Protocol as executed by this node. This value is used as the Root Identifier parameter in all Configuration Bridge PDUs originated by this node. This object is supported by R1.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

mstpExternalRootCost 1.1.890.1.5.13.5.13.7.2
The cost of the path to the root as seen from this bridge. This object is supported by R1.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mstpExternalRootPortId 1.1.890.1.5.13.5.13.7.3
The port number of the port which offers the lowest cost path from this bridge to the root bridge. This object is supported by R1.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

mstpExternalRootMaxAge 1.1.890.1.5.13.5.13.7.4
The maximum age of Spanning Tree Protocol information learned from the network on any port before it is discarded, in units of hundredths of a second. This is the actual value that this bridge is currently using. This object is supported by R1.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  Timeout  

mstpExternalRootHelloTime 1.1.890.1.5.13.5.13.7.5
The amount of time between the transmission of Configuration bridge PDUs by this node on any port when it is the root of the spanning tree or trying to become so, in units of hundredths of a second. This is the actual value that this bridge is currently using. This object is supported by R1.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  Timeout  

mstpExternalRootForwardDelay 1.1.890.1.5.13.5.13.7.6
This time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the Forwarding state. The value determines how long the port stays in each of the Listening and Learning states, which precede the Forwarding state. This value is also used, when a topology change has been detected and is underway, to age all dynamic entries in the Forwarding Database. This object is supported by R1.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  Timeout  

mstpPortStatsTable 1.1.890.1.5.13.5.13.7.7
A table that contains port-specific MSTP statistics. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MstpPortStatsEntry

mstpPortStatsEntry 1.1.890.1.5.13.5.13.7.7.1
A list of MSTP statistics maintained by each port.
Status: current Access: not-accessible
OBJECT-TYPE    
  MstpPortStatsEntry  

mstpPortStatsExternalRootId 1.1.890.1.5.13.5.13.7.7.1.1
The unique Bridge Identifier of the Bridge recorded as the Root in the Configuration BPDUs transmitted by the Designated Bridge for the segment to which the port is attached.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

mstpPortStatsExternalRootCost 1.1.890.1.5.13.5.13.7.7.1.2
The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mstpPortStatsExternalPortCost 1.1.890.1.5.13.5.13.7.7.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mstpPortStatsOperEdgePort 1.1.890.1.5.13.5.13.7.7.1.4
The operational value of the Edge Port parameter.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

mstpPortStatsOperPoint2Point 1.1.890.1.5.13.5.13.7.7.1.5
The operational point-to-point status of the LAN segment attached to this port. It indicates whether a port is considered to have a point-to-point connection or not.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

mstpPortStatsMACOperational 1.1.890.1.5.13.5.13.7.7.1.6
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

mstpPortStatsRecvInternal 1.1.890.1.5.13.5.13.7.7.1.7
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

mstpPortStatsRxStpCfgBPDU 1.1.890.1.5.13.5.13.7.7.1.8
The total number of received Configuration BPDUs.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mstpPortStatsRxStpTcnBPDU 1.1.890.1.5.13.5.13.7.7.1.9
The total number of received Topology Change Notification (TCN) Messages.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mstpPortStatsRxRstpBPDU 1.1.890.1.5.13.5.13.7.7.1.10
The total number of received RST BPDUs.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mstpPortStatsRxMstpBPDU 1.1.890.1.5.13.5.13.7.7.1.11
The total number of received MST BPDUs.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mstpXstStatsTable 1.1.890.1.5.13.5.13.7.8
A table that contains MSTP statistics for multiple spanning trees. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MstpXstStatsEntry

mstpXstStatsEntry 1.1.890.1.5.13.5.13.7.8.1
An entry of mstpXstStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MstpXstStatsEntry  

mstpXstStatsBridgeId 1.1.890.1.5.13.5.13.7.8.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

mstpXstStatsTimeSinceTopologyChange 1.1.890.1.5.13.5.13.7.8.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

mstpXstStatsTopologyChangesCount 1.1.890.1.5.13.5.13.7.8.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mstpXstStatsInternalRootPortId 1.1.890.1.5.13.5.13.7.8.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

mstpXstStatsInternalRootId 1.1.890.1.5.13.5.13.7.8.1.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

mstpXstStatsInternalRootCost 1.1.890.1.5.13.5.13.7.8.1.6
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mstpXstPortStatsTable 1.1.890.1.5.13.5.13.7.9
A table that contains MSTP port statistics for multiple spanning trees. This table is supported by R1.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MstpXstPortStatsEntry

mstpXstPortStatsEntry 1.1.890.1.5.13.5.13.7.9.1
An entry of mstpXstPortStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MstpXstPortStatsEntry  

mstpXstPortStatsUptime 1.1.890.1.5.13.5.13.7.9.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

mstpXstPortStatsPortId 1.1.890.1.5.13.5.13.7.9.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

mstpXstPortStatsState 1.1.890.1.5.13.5.13.7.9.1.3
The port's current state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), discarding(2), learning(3), forwarding(4), unknown(5)  

mstpXstPortStatsDesignatedBridgeId 1.1.890.1.5.13.5.13.7.9.1.4
The Bridge Identifier of the bridge which this port considers to be the Designated Bridge for this port's segment.
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

mstpXstPortStatsDesignatedPortId 1.1.890.1.5.13.5.13.7.9.1.5
The Port Identifier of the port on the Designated Bridge for this port's segment.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

mstpXstPortStatsInternalPortCost 1.1.890.1.5.13.5.13.7.9.1.6
The path cost of the Designated Port of the segment connected to this port. This value is compared to the Root Path Cost field in received bridge PDUs.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mstpXstPortStatsInternalRootId 1.1.890.1.5.13.5.13.7.9.1.7
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  BridgeId  

vdslLinePerfTable 1.1.890.1.5.13.5.13.8.1
The table displays VDSL line performance. This table is supported by R2.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLinePerfEntry

vdslLinePerfEntry 1.1.890.1.5.13.5.13.8.1.1
An entry of vdslLinePerfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLinePerfEntry  

vdslLinePerfVtucCrc 1.1.890.1.5.13.5.13.8.1.1.1
The number of CRC errors since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfVturCrc 1.1.890.1.5.13.5.13.8.1.1.2
The number of CRC errors since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfVtucFec 1.1.890.1.5.13.5.13.8.1.1.3
The number of FEC errors since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfVturFec 1.1.890.1.5.13.5.13.8.1.1.4
The number of FEC errors since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfVtucLofs 1.1.890.1.5.13.5.13.8.1.1.5
Count of the number of Loss of Framing failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfVturLofs 1.1.890.1.5.13.5.13.8.1.1.6
Count of the number of Loss of Framing failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfVtucLoss 1.1.890.1.5.13.5.13.8.1.1.7
Count of the number of Loss of Signal failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfVturLoss 1.1.890.1.5.13.5.13.8.1.1.8
Count of the number of Loss of Signal failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfVtucLprs 1.1.890.1.5.13.5.13.8.1.1.9
Count of the number of Loss of Power failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfVturLprs 1.1.890.1.5.13.5.13.8.1.1.10
Count of the number of Loss of Power failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfVtucLols 1.1.890.1.5.13.5.13.8.1.1.11
Count of the number of Loss of Link failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfVturLols 1.1.890.1.5.13.5.13.8.1.1.12
Count of the number of Loss of Link failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfVtucESs 1.1.890.1.5.13.5.13.8.1.1.13
Count of the number of Errored Seconds since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfVturESs 1.1.890.1.5.13.5.13.8.1.1.14
Count of the number of Errored Seconds since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfVtucSESs 1.1.890.1.5.13.5.13.8.1.1.15
Count of the number of Severely Errored Seconds since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfVturSESs 1.1.890.1.5.13.5.13.8.1.1.16
Count of the number of Severely Errored Seconds since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfVtucUASs 1.1.890.1.5.13.5.13.8.1.1.17
Count of the number of Unavailable Seconds since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfVturUASs 1.1.890.1.5.13.5.13.8.1.1.18
Count of the number of Unavailable Seconds since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfInmVtucEqInp 1.1.890.1.5.13.5.13.8.1.1.19
The INM Equivalent Inp histogram since last link up. An array of 68 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17 bins of the histogram. The particular index of the bin incremented by an impulse noise event is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfInmVturEqInp 1.1.890.1.5.13.5.13.8.1.1.20
The INM Equivalent Inp histogram since last link up. An array of 68 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17 bins of the histogram. The particular index of the bin incremented by an impulse noise event is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfInmVtucIAT 1.1.890.1.5.13.5.13.8.1.1.21
The INM Inter Arrival Time histogram since last link up. An array of 32 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram. The index of the particular bin incremented by an complete impulse noise event is determained from the following INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfInmVturIAT 1.1.890.1.5.13.5.13.8.1.1.22
The INM Inter Arrival Time histogram since last link up. An array of 32 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram. The index of the particular bin incremented by an complete impulse noise event is determained from the following INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfInmVtucME 1.1.890.1.5.13.5.13.8.1.1.23
The INM total measurement since last link up. This indication occurs every time a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfInmVturME 1.1.890.1.5.13.5.13.8.1.1.24
The INM total measurement since last link up. This indication occurs every time a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfVtucRx 1.1.890.1.5.13.5.13.8.1.1.25
Number of codewords retransmitted since last link up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfVturRx 1.1.890.1.5.13.5.13.8.1.1.26
Number of codewords retransmitted since last link up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfVtucRxCorrected 1.1.890.1.5.13.5.13.8.1.1.27
Number of codewords corrected through retransmission since last link up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfVturRxCorrected 1.1.890.1.5.13.5.13.8.1.1.28
Number of codewords corrected through retransmission since last link up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfVtucRxUncorrected 1.1.890.1.5.13.5.13.8.1.1.29
Number of codewords left uncorrected after retransmission since last link up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfVturRxUncorrected 1.1.890.1.5.13.5.13.8.1.1.30
Number of codewords left uncorrected after retransmission since last link up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfVtucLEFTRs 1.1.890.1.5.13.5.13.8.1.1.31
Low Error-Free Throughput Rate Seconds since last link up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfVturLEFTRs 1.1.890.1.5.13.5.13.8.1.1.32
Low Error-Free Throughput Rate Seconds since last link up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfVtucErrFreeBits 1.1.890.1.5.13.5.13.8.1.1.33
The number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) since last link up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfVturErrFreeBits 1.1.890.1.5.13.5.13.8.1.1.34
The number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) since last link up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfVtucMinEftr 1.1.890.1.5.13.5.13.8.1.1.35
Lowest EFTR of VTU-C observed since last link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfVturMinEftr 1.1.890.1.5.13.5.13.8.1.1.36
Lowest EFTR of VTU-R observed since last link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLineStatsTable 1.1.890.1.5.13.5.13.8.2
The table displays VDSL line statistics. This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineStatsEntry

vdslLineStatsEntry 1.1.890.1.5.13.5.13.8.2.1
An entry of vdslLineStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineStatsEntry  

vdslLineStatsVtucBits1 1.1.890.1.5.13.5.13.8.2.1.1
The object provides Bits for the VTU-C 1024 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 15.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVtucBits2 1.1.890.1.5.13.5.13.8.2.1.2
The object provides Bits for the VTU-C 1024 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 15.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVtucBits3 1.1.890.1.5.13.5.13.8.2.1.3
The object provides Bits for the VTU-C 1024 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 15.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVtucBits4 1.1.890.1.5.13.5.13.8.2.1.4
The object provides Bits for the VTU-C 1024 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 15.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVturBits1 1.1.890.1.5.13.5.13.8.2.1.5
The object provides Bits for the VTU-R 1024 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 15.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVturBits2 1.1.890.1.5.13.5.13.8.2.1.6
The object provides Bits for the VTU-R 1024 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 15.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVturBits3 1.1.890.1.5.13.5.13.8.2.1.7
The object provides Bits for the VTU-R 1024 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 15.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVturBits4 1.1.890.1.5.13.5.13.8.2.1.8
The object provides Bits for the VTU-R 1024 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 15.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVtucGain1 1.1.890.1.5.13.5.13.8.2.1.9
The object provides Gain for the VTU-C 512 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 4093. Each value in this array is 16 bits wide. The gain value is represented as a multiple of 1/512 on linear scale.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVtucGain2 1.1.890.1.5.13.5.13.8.2.1.10
The object provides Gain for the VTU-C 512 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 4093. Each value in this array is 16 bits wide. The gain value is represented as a multiple of 1/512 on linear scale.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVtucGain3 1.1.890.1.5.13.5.13.8.2.1.11
The object provides Gain for the VTU-C 512 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 4093. Each value in this array is 16 bits wide. The gain value is represented as a multiple of 1/512 on linear scale.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVtucGain4 1.1.890.1.5.13.5.13.8.2.1.12
The object provides Gain for the VTU-C 512 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 4093. Each value in this array is 16 bits wide. The gain value is represented as a multiple of 1/512 on linear scale.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVtucGain5 1.1.890.1.5.13.5.13.8.2.1.13
The object provides Gain for the VTU-C 512 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 4093. Each value in this array is 16 bits wide. The gain value is represented as a multiple of 1/512 on linear scale.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVtucGain6 1.1.890.1.5.13.5.13.8.2.1.14
The object provides Gain for the VTU-C 512 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 4093. Each value in this array is 16 bits wide. The gain value is represented as a multiple of 1/512 on linear scale.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVtucGain7 1.1.890.1.5.13.5.13.8.2.1.15
The object provides Gain for the VTU-C 512 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 4093. Each value in this array is 16 bits wide. The gain value is represented as a multiple of 1/512 on linear scale.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVtucGain8 1.1.890.1.5.13.5.13.8.2.1.16
The object provides Gain for the VTU-C 512 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 4093. Each value in this array is 16 bits wide. The gain value is represented as a multiple of 1/512 on linear scale.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVturGain1 1.1.890.1.5.13.5.13.8.2.1.17
The object provides Gain for the VTU-R 512 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 4093. Each value in this array is 16 bits wide. The gain value is represented as a multiple of 1/512 on linear scale.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVturGain2 1.1.890.1.5.13.5.13.8.2.1.18
The object provides Gain for the VTU-R 512 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 4093. Each value in this array is 16 bits wide. The gain value is represented as a multiple of 1/512 on linear scale.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVturGain3 1.1.890.1.5.13.5.13.8.2.1.19
The object provides Gain for the VTU-R 512 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 4093. Each value in this array is 16 bits wide. The gain value is represented as a multiple of 1/512 on linear scale.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVturGain4 1.1.890.1.5.13.5.13.8.2.1.20
The object provides Gain for the VTU-R 512 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 4093. Each value in this array is 16 bits wide. The gain value is represented as a multiple of 1/512 on linear scale.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVturGain5 1.1.890.1.5.13.5.13.8.2.1.21
The object provides Gain for the VTU-R 512 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 4093. Each value in this array is 16 bits wide. The gain value is represented as a multiple of 1/512 on linear scale.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVturGain6 1.1.890.1.5.13.5.13.8.2.1.22
The object provides Gain for the VTU-R 512 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 4093. Each value in this array is 16 bits wide. The gain value is represented as a multiple of 1/512 on linear scale.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVturGain7 1.1.890.1.5.13.5.13.8.2.1.23
The object provides Gain for the VTU-R 512 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 4093. Each value in this array is 16 bits wide. The gain value is represented as a multiple of 1/512 on linear scale.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVturGain8 1.1.890.1.5.13.5.13.8.2.1.24
The object provides Gain for the VTU-R 512 subcarriers. Each subcarrier takes two octets to store the value. The value is in the range 0 to 4093. Each value in this array is 16 bits wide. The gain value is represented as a multiple of 1/512 on linear scale.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVtucHlog 1.1.890.1.5.13.5.13.8.2.1.25
The object provides Hlog for the VTU-C 512 subcarriers. Each subcarrier takes two octets to store the value. The real Hlog(f) value is represented as (6-m(i)/10), with m(i) in the range 0 to 1022. A special value m=1023 indicates that no measurement could be done for the sub-carrier group becauseit is out of the passband or that the attenuation is out of range to be represented. Each value in this array is 16 bits wide.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVturHlog 1.1.890.1.5.13.5.13.8.2.1.26
The object provides Hlog for the VTU-R 512 subcarriers. Each subcarrier takes two octets to store the value. The real Hlog(f) value is represented as (6-m(i)/10), with m(i) in the range 0 to 1022. A special value m=1023 indicates that no measurement could be done for the sub-carrier group because it is out of the passband or that the attenuation is out ofrange to be represented. Each value in this array is 16 bits wide.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVtucQln 1.1.890.1.5.13.5.13.8.2.1.27
The object provides Qln for the VTU-C 512 subcarriers. Each subcarrier takes two octets to store the value. The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the range 0 to 254. A special value n(i)=255 indicates that no measurement could be done for the sub-carrier group. Each value in this array is 8 bits wide.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVturQln 1.1.890.1.5.13.5.13.8.2.1.28
The object provides Qln for the VTU-R 512 subcarriers. Each subcarrier takes two octets to store the value. The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the range 0 to 254. A special value n(i)=255 indicates that no measurement could be done for the sub-carrier group. Each value in this array is 8 bits wide.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVtucSnr 1.1.890.1.5.13.5.13.8.2.1.29
The object provides Snr for the VTU-C 512 subcarriers. Each subcarrier takes one octets to store the value. Octet i is set to a value in the range 0 to 254 (-32 + vdslLineStatsVtucSnr (i)/2) in dB (i.e., -32 to 95dB). Each value in this array is 8 bits wide. A special value 255 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVturSnr 1.1.890.1.5.13.5.13.8.2.1.30
The object provides Snr for the VTU-R 512 subcarriers. Each subcarrier takes one octets to store the value. Octet i is set to a value in the range 0 to 254 (-32 + vdslLineStatsVturSnr (i)/2) in dB (i.e., -32 to 95dB). Each value in this array is 8 bits wide. A special value 255 indicates that no measurement could be done for the sub-carrier group.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVtucTssi 1.1.890.1.5.13.5.13.8.2.1.31
The object provides Tssi for the VTU-C 512 subcarriers. Each subcarrier takes two octets to store the value. Each value in this array is 16 bits wide. The tssi value is represented as a multiple of 1/32768 on linear scale.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsVturTssi 1.1.890.1.5.13.5.13.8.2.1.32
The object provides Tssi for the VTU-R 512 subcarriers. Each subcarrier takes two octets to store the value. Each value in this array is 16 bits wide. The tssi value is represented as a multiple of 1/32768 on linear scale.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

vdslLineStatsProtocol 1.1.890.1.5.13.5.13.8.2.1.33
The actual line protocol.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), vdsl-8a(2), vdsl-8b(3), vdsl-8c(4), vdsl-8d(5), vdsl-12a(6), vdsl-12b(7), vdsl-17a(8), vdsl-30a(9), adsl2plus(10)  

vdslLineStatsUsCodingMode 1.1.890.1.5.13.5.13.8.2.1.34
The upstream coding mode of the line. This object is supported by R5.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), trellis(2), reedSolomon(3), trellisAndReedSolomon(4)  

vdslLineStatsDsCodingMode 1.1.890.1.5.13.5.13.8.2.1.35
The downstream coding mode of the line. This object is supported by R5.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(1), trellis(2), reedSolomon(3), trellisAndReedSolomon(4)  

vdslLineStatsVtucHlogGroupSize 1.1.890.1.5.13.5.13.8.2.1.36
Number of sub-carriers per group used to report the H(f) linear representation values for the respective transmission direction. The valid values are 1, 2, 4 and 8. This object is supported by R5.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineStatsVturHlogGroupSize 1.1.890.1.5.13.5.13.8.2.1.37
Number of sub-carriers per group used to report the H(f) linear representation values for the respective transmission direction. The valid values are 1, 2, 4 and 8. This object is supported by R5.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineStatsVtucQlnGroupSize 1.1.890.1.5.13.5.13.8.2.1.38
Number of sub-carriers per group used to report the Quiet Line Noise values for the respective transmission direction. The valid values are 1, 2, 4 and 8. This object is supported by R5.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineStatsVturQlnGroupSize 1.1.890.1.5.13.5.13.8.2.1.39
Number of sub-carriers per group used to report the Quiet Line Noise values for the respective transmission direction. The valid values are 1, 2, 4 and 8. This object is supported by R5.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineStatsVtucSnrGroupSize 1.1.890.1.5.13.5.13.8.2.1.40
Number of sub-carriers per group used to report the SNR values on the respective transmission direction. The valid values are 1, 2, 4 and 8. This object is supported by R5.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineStatsVturSnrGroupSize 1.1.890.1.5.13.5.13.8.2.1.41
Number of sub-carriers per group used to report the SNR values on the respective transmission direction. The valid values are 1, 2, 4 and 8. This object is supported by R5.02 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineStatsVtucRxPower 1.1.890.1.5.13.5.13.8.2.1.42
Receive power of vtuc (in unit of 0.1 dBm).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineStatsVturRxPower 1.1.890.1.5.13.5.13.8.2.1.43
Receive power of vtur (in unit of 0.1 dBm).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineStatsVtucSnrMargin 1.1.890.1.5.13.5.13.8.2.1.44
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineStatsVturSnrMargin 1.1.890.1.5.13.5.13.8.2.1.45
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineStatsVtucSigAtten 1.1.890.1.5.13.5.13.8.2.1.46
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineStatsVturSigAtten 1.1.890.1.5.13.5.13.8.2.1.47
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineStatsVtucLineAtten 1.1.890.1.5.13.5.13.8.2.1.48
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineStatsVturLineAtten 1.1.890.1.5.13.5.13.8.2.1.49
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineUsBandPlanTable 1.1.890.1.5.13.5.13.8.3
The table displays VDSL line actual band plan. This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineUsBandPlanEntry

vdslLineUsBandPlanEntry 1.1.890.1.5.13.5.13.8.3.1
An entry of vdslLineUsBandPlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineUsBandPlanEntry  

vdslLineUsBandId 1.1.890.1.5.13.5.13.8.3.1.1
Ihe id of the upstream pass band, starting from 1.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineUsBandStartToneId 1.1.890.1.5.13.5.13.8.3.1.2
The starting tone of the band.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineUsBandStopToneId 1.1.890.1.5.13.5.13.8.3.1.3
The stopping tone of the band.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineDsBandPlanTable 1.1.890.1.5.13.5.13.8.4
The table displays VDSL line actual band plan. This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineDsBandPlanEntry

vdslLineDsBandPlanEntry 1.1.890.1.5.13.5.13.8.4.1
An entry of vdslLineDsBandPlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineDsBandPlanEntry  

vdslLineDsBandId 1.1.890.1.5.13.5.13.8.4.1.1
Ihe id of the downstream pass band, starting from 1.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineDsBandStartToneId 1.1.890.1.5.13.5.13.8.4.1.2
The starting tone of the band.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineDsBandStopToneId 1.1.890.1.5.13.5.13.8.4.1.3
The stopping tone of the band.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineUsResultMaskTable 1.1.890.1.5.13.5.13.8.5
The table displays VDSL line actual PSD mask. This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineUsResultMaskEntry

vdslLineUsResultMaskEntry 1.1.890.1.5.13.5.13.8.5.1
An entry of vdslLineUsResultMaskTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineUsResultMaskEntry  

vdslLineUsMaskId 1.1.890.1.5.13.5.13.8.5.1.1
The id of the turning point of the mask, starting from 1.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineUsMaskTone 1.1.890.1.5.13.5.13.8.5.1.2
The tone id.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineUsMaskPsd 1.1.890.1.5.13.5.13.8.5.1.3
The psd, in 0.1 dBm/Hz.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineDsResultMaskTable 1.1.890.1.5.13.5.13.8.6
The table displays VDSL line actual PSD mask. This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLineDsResultMaskEntry

vdslLineDsResultMaskEntry 1.1.890.1.5.13.5.13.8.6.1
An entry of vdslLineDsResultMaskTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLineDsResultMaskEntry  

vdslLineDsMaskId 1.1.890.1.5.13.5.13.8.6.1.1
The id of the turning point of the mask, starting from 1.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineDsMaskTone 1.1.890.1.5.13.5.13.8.6.1.2
The tone id.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLineDsMaskPsd 1.1.890.1.5.13.5.13.8.6.1.3
The psd, in 0.1 dBm/Hz.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vdslLinePerfCurrTable 1.1.890.1.5.13.5.13.8.7
The table displays VDSL line current GINP/SOS/INM performance statistics.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLinePerfCurrEntry

vdslLinePerfCurrEntry 1.1.890.1.5.13.5.13.8.7.1
An entry of vdslLinePerfCurrTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLinePerfCurrEntry  

vdslLinePerfCurrInmVtucEqInp 1.1.890.1.5.13.5.13.8.7.1.1
The INM Equivalent Inp histogram since system boot up. An array of 68 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17 bins of the histogram. The particular index of the bin incremented by an impulse noise event is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurrInmVturEqInp 1.1.890.1.5.13.5.13.8.7.1.2
The INM Equivalent Inp histogram since system boot up. An array of 68 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17 bins of the histogram. The particular index of the bin incremented by an impulse noise event is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurr15MInmVtucEqInp 1.1.890.1.5.13.5.13.8.7.1.3
The INM Equivalent Inp histogram during this 15 minutes interval. An array of 68 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17 bins of the histogram. The particular index of the bin incremented by an impulse noise event is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurr15MInmVturEqInp 1.1.890.1.5.13.5.13.8.7.1.4
The INM Equivalent Inp histogram during this 15 minutes interval. An array of 68 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17 bins of the histogram. The particular index of the bin incremented by an impulse noise event is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurr1DayInmVtucEqInp 1.1.890.1.5.13.5.13.8.7.1.5
The INM Equivalent Inp histogram during this 1 day interval. An array of 68 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17 bins of the histogram. The particular index of the bin incremented by an impulse noise event is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurr1DayInmVturEqInp 1.1.890.1.5.13.5.13.8.7.1.6
The INM Equivalent Inp histogram during this 1 day interval. An array of 68 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17 bins of the histogram. The particular index of the bin incremented by an impulse noise event is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurrInmVtucIAT 1.1.890.1.5.13.5.13.8.7.1.7
The INM Inter Arrival Time histogram since system boot up. An array of 32 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram. The index of the particular bin incremented by an complete impulse noise event is determained from the following INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurrInmVturIAT 1.1.890.1.5.13.5.13.8.7.1.8
The INM Inter Arrival Time histogram since system boot up. An array of 32 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram. The index of the particular bin incremented by an complete impulse noise event is determained from the following INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurr15MInmVtucIAT 1.1.890.1.5.13.5.13.8.7.1.9
The INM Inter Arrival Time histogram during this 15 minutes interval. An array of 32 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram. The index of the particular bin incremented by an complete impulse noise event is determained from the following INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurr15MInmVturIAT 1.1.890.1.5.13.5.13.8.7.1.10
The INM Inter Arrival Time histogram during this 15 minutes interval. An array of 32 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram. The index of the particular bin incremented by an complete impulse noise event is determained from the following INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurr1DayInmVtucIAT 1.1.890.1.5.13.5.13.8.7.1.11
The INM Inter Arrival Time histogram during this 1 day interval. An array of 32 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram. The index of the particular bin incremented by an complete impulse noise event is determained from the following INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurr1DayInmVturIAT 1.1.890.1.5.13.5.13.8.7.1.12
The INM Inter Arrival Time histogram during this 1 day interval. An array of 32 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram. The index of the particular bin incremented by an complete impulse noise event is determained from the following INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurrInmVtucME 1.1.890.1.5.13.5.13.8.7.1.13
The INM total measurement since system boot up. This indication occurs every time a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurrInmVturME 1.1.890.1.5.13.5.13.8.7.1.14
The INM total measurement since system boot up. This indication occurs every time a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurr15MInmVtucME 1.1.890.1.5.13.5.13.8.7.1.15
The INM total measurement during this 15 minutes interval. This indication occurs every time a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurr15MInmVturME 1.1.890.1.5.13.5.13.8.7.1.16
The INM total measurement during this 15 minutes interval. This indication occurs every time a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurr1DayInmVtucME 1.1.890.1.5.13.5.13.8.7.1.17
The INM total measurement during this 1 day interval. This indication occurs every time a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurr1DayInmVturME 1.1.890.1.5.13.5.13.8.7.1.18
The INM total measurement during this 1 day interval. This indication occurs every time a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurrVtucRx 1.1.890.1.5.13.5.13.8.7.1.19
Number of codewords retransmitted since system boot up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurrVturRx 1.1.890.1.5.13.5.13.8.7.1.20
Number of codewords retransmitted since system boot up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr15MVtucRx 1.1.890.1.5.13.5.13.8.7.1.21
Number of codewords retransmitted during this 15 minutes interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr15MVturRx 1.1.890.1.5.13.5.13.8.7.1.22
Number of codewords retransmitted during this 15 minutes interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr1DayVtucRx 1.1.890.1.5.13.5.13.8.7.1.23
Number of codewords retransmitted during this 1 day interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr1DayVturRx 1.1.890.1.5.13.5.13.8.7.1.24
Number of codewords retransmitted during this 1 day interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurrVtucRxCorrected 1.1.890.1.5.13.5.13.8.7.1.25
Number of codewords corrected through retransmission since system boot up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurrVturRxCorrected 1.1.890.1.5.13.5.13.8.7.1.26
Number of codewords corrected through retransmission since system boot up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr15MVtucRxCorrected 1.1.890.1.5.13.5.13.8.7.1.27
Number of codewords corrected through retransmission during this 15 minutes interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr15MVturRxCorrected 1.1.890.1.5.13.5.13.8.7.1.28
Number of codewords corrected through retransmission during this 15 minutes interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr1DayVtucRxCorrected 1.1.890.1.5.13.5.13.8.7.1.29
Number of codewords corrected through retransmission during this 1 day interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr1DayVturRxCorrected 1.1.890.1.5.13.5.13.8.7.1.30
Number of codewords corrected through retransmission during this 1 day interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurrVtucRxUncorrected 1.1.890.1.5.13.5.13.8.7.1.31
Number of codewords left uncorrected after retransmission since system boot up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurrVturRxUncorrected 1.1.890.1.5.13.5.13.8.7.1.32
Number of codewords left uncorrected after retransmission since system boot up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr15MVtucRxUncorrected 1.1.890.1.5.13.5.13.8.7.1.33
Number of codewords left uncorrected after retransmission during this 15 minutes interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr15MVturRxUncorrected 1.1.890.1.5.13.5.13.8.7.1.34
Number of codewords left uncorrected after retransmission during this 15 minutes interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr1DayVtucRxUncorrected 1.1.890.1.5.13.5.13.8.7.1.35
Number of codewords left uncorrected after retransmission during this 1 day interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr1DayVturRxUncorrected 1.1.890.1.5.13.5.13.8.7.1.36
Number of codewords left uncorrected after retransmission during this 1 day interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurrVtucLEFTRs 1.1.890.1.5.13.5.13.8.7.1.37
Low Error-Free Throughput Rate Seconds since system boot up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurrVturLEFTRs 1.1.890.1.5.13.5.13.8.7.1.38
Low Error-Free Throughput Rate Seconds since system boot up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr15MVtucLEFTRs 1.1.890.1.5.13.5.13.8.7.1.39
Low Error-Free Throughput Rate Seconds during this 15 minutes interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr15MVturLEFTRs 1.1.890.1.5.13.5.13.8.7.1.40
Low Error-Free Throughput Rate Seconds during this 15 minutes interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr1DayVtucLEFTRs 1.1.890.1.5.13.5.13.8.7.1.41
Low Error-Free Throughput Rate Seconds during this 1 day interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr1DayVturLEFTRs 1.1.890.1.5.13.5.13.8.7.1.42
Low Error-Free Throughput Rate Seconds during this 1 day interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurrVtucErrFreeBits 1.1.890.1.5.13.5.13.8.7.1.43
The number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) since system boot up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurrVturErrFreeBits 1.1.890.1.5.13.5.13.8.7.1.44
The number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) since system boot up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr15MVtucErrFreeBits 1.1.890.1.5.13.5.13.8.7.1.45
The number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) during this 15 minutes interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr15MVturErrFreeBits 1.1.890.1.5.13.5.13.8.7.1.46
The number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) during this 15 minutes interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr1DayVtucErrFreeBits 1.1.890.1.5.13.5.13.8.7.1.47
The number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) this 1 day interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurr1DayVturErrFreeBits 1.1.890.1.5.13.5.13.8.7.1.48
The number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) this 1 day interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfCurrVtucMinEftr 1.1.890.1.5.13.5.13.8.7.1.49
Lowest EFTR of VTU-C observed in the current interval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurrVturMinEftr 1.1.890.1.5.13.5.13.8.7.1.50
Lowest EFTR of VTU-R observed in the current interval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurr15MinVtucMinEftr 1.1.890.1.5.13.5.13.8.7.1.51
Lowest EFTR of VTU-C observed in the current 15 minutes interval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurr15MinVturMinEftr 1.1.890.1.5.13.5.13.8.7.1.52
Lowest EFTR of VTU-R observed in the current 15 minutes interval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurr1DayVtucMinEftr 1.1.890.1.5.13.5.13.8.7.1.53
Lowest EFTR of VTU-C observed in the current 1 day interval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfCurr1DayVturMinEftr 1.1.890.1.5.13.5.13.8.7.1.54
Lowest EFTR of VTU-R observed in the current 1 day interval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfHist15MinTable 1.1.890.1.5.13.5.13.8.8
The table displays VDSL line 15-Min SOS/GINP/INM performance stats.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLinePerfHist15MinEntry

vdslLinePerfHist15MinEntry 1.1.890.1.5.13.5.13.8.8.1
An entry of vdslLinePerfCurrTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLinePerfHist15MinEntry  

vdslLinePerfHist15MInmVtucEqInp 1.1.890.1.5.13.5.13.8.8.1.1
The INM Equivalent Inp histogram during 15min interval. An array of 68 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17 bins of the histogram. The particular index of the bin incremented by an impulse noise event is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfHist15MInmVturEqInp 1.1.890.1.5.13.5.13.8.8.1.2
The INM Equivalent Inp histogram during 15min interval. An array of 68 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17 bins of the histogram. The particular index of the bin incremented by an impulse noise event is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfHist15MInmVtucIAT 1.1.890.1.5.13.5.13.8.8.1.3
The INM Inter Arrival Time histogram during 15min interval. An array of 32 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram. The index of the particular bin incremented by an complete impulse noise event is determained from the following INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfHist15MInmVturIAT 1.1.890.1.5.13.5.13.8.8.1.4
The INM Inter Arrival Time histogram during 15min interval. An array of 32 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram. The index of the particular bin incremented by an complete impulse noise event is determained from the following INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfHist15MInmVtucME 1.1.890.1.5.13.5.13.8.8.1.5
The INM total measurement during 15min interval.This indication occurs every time a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfHist15MInmVturME 1.1.890.1.5.13.5.13.8.8.1.6
The INM total measurement during 15min interval.This indication occurs every time a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfHist15MVtucRtx 1.1.890.1.5.13.5.13.8.8.1.7
Number of codewords retransmitted during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist15MVturRtx 1.1.890.1.5.13.5.13.8.8.1.8
Number of codewords retransmitted during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist15MVtucRtxCorrected 1.1.890.1.5.13.5.13.8.8.1.9
Number of codewords corrected through retransmission during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist15MVturRtxCorrected 1.1.890.1.5.13.5.13.8.8.1.10
Number of codewords corrected through retransmission during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist15MVtucRtxUncorrected 1.1.890.1.5.13.5.13.8.8.1.11
Number of codewords left uncorrected after retransmission during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist15MVturRtxUncorrected 1.1.890.1.5.13.5.13.8.8.1.12
Number of codewords left uncorrected after retransmission during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist15MVtucLEFTRs 1.1.890.1.5.13.5.13.8.8.1.13
Low Error-Free Throughput Rate Seconds during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist15MVturLEFTRs 1.1.890.1.5.13.5.13.8.8.1.14
Low Error-Free Throughput Rate Seconds during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist15MVtucErrFreeBits 1.1.890.1.5.13.5.13.8.8.1.15
The number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist15MVturErrFreeBits 1.1.890.1.5.13.5.13.8.8.1.16
The number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist15MVtucMinEftr 1.1.890.1.5.13.5.13.8.8.1.17
Lowest EFTR of VTU-C observed during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfHist15MVturMinEftr 1.1.890.1.5.13.5.13.8.8.1.18
Lowest EFTR of VTU-R observed during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfHist1DayTable 1.1.890.1.5.13.5.13.8.9
The table displays VDSL line 1-Day SOS/GINP/INM performance stats.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslLinePerfHist1DayEntry

vdslLinePerfHist1DayEntry 1.1.890.1.5.13.5.13.8.9.1
An entry of vdslLinePerfHist1DayTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslLinePerfHist1DayEntry  

vdslLinePerfHist1DayInmVtucEqInp 1.1.890.1.5.13.5.13.8.9.1.1
The INM Equivalent Inp histogram during 1 day interval. An array of 68 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17 bins of the histogram. The particular index of the bin incremented by an impulse noise event is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfHist1DayInmVturEqInp 1.1.890.1.5.13.5.13.8.9.1.2
The INM Equivalent Inp histogram during 1 day interval. An array of 68 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17 bins of the histogram. The particular index of the bin incremented by an impulse noise event is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfHist1DayInmVtucIAT 1.1.890.1.5.13.5.13.8.9.1.3
The INM Inter Arrival Time histogram during 1 day interval. An array of 32 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram. The index of the particular bin incremented by an complete impulse noise event is determained from the following INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfHist1DayInmVturIAT 1.1.890.1.5.13.5.13.8.9.1.4
The INM Inter Arrival Time histogram during 1 day interval. An array of 32 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram. The index of the particular bin incremented by an complete impulse noise event is determained from the following INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfHist1DayInmVtucME 1.1.890.1.5.13.5.13.8.9.1.5
The INM total measurement during 1 day interval.This indication occurs every time a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfHist1DayInmVturME 1.1.890.1.5.13.5.13.8.9.1.6
The INM total measurement during 1 day interval.This indication occurs every time a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfHist1DayVtucRtx 1.1.890.1.5.13.5.13.8.9.1.7
Number of codewords retransmitted during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist1DayVturRtx 1.1.890.1.5.13.5.13.8.9.1.8
Number of codewords retransmitted during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist1DayVtucRtxCorrected 1.1.890.1.5.13.5.13.8.9.1.9
Number of codewords corrected through retransmission during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist1DayVturRtxCorrected 1.1.890.1.5.13.5.13.8.9.1.10
Number of codewords corrected through retransmission during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist1DayVtucRtxUncorrected 1.1.890.1.5.13.5.13.8.9.1.11
Number of codewords left uncorrected after retransmission during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist1DayVturRtxUncorrected 1.1.890.1.5.13.5.13.8.9.1.12
Number of codewords left uncorrected after retransmission during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist1DayVtucLEFTRs 1.1.890.1.5.13.5.13.8.9.1.13
Low Error-Free Throughput Rate Seconds during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist1DayVturLEFTRs 1.1.890.1.5.13.5.13.8.9.1.14
Low Error-Free Throughput Rate Seconds during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist1DayVtucErrFreeBits 1.1.890.1.5.13.5.13.8.9.1.15
The number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist1DayVturErrFreeBits 1.1.890.1.5.13.5.13.8.9.1.16
The number of bits belonging to correct DTUs leaving the Rx PMS-TC x 2(-16) during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslLinePerfHist1DayVtucMinEftr 1.1.890.1.5.13.5.13.8.9.1.17
Lowest EFTR of VTU-C observed during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslLinePerfHist1DayVturMinEftr 1.1.890.1.5.13.5.13.8.9.1.18
Lowest EFTR of VTU-R observed during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslChanStatsTable 1.1.890.1.5.13.5.13.8.10
The table displays VDSL channel Status.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslChanStatsEntry

vdslChanStatsEntry 1.1.890.1.5.13.5.13.8.10.1
An entry of vdslChanStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslChanStatsEntry  

vdslChanActualRaMode 1.1.890.1.5.13.5.13.8.10.1.2
The actual RA mode. The possible values are: fixedRateMode(1) - Fixed rate mode raInit(2) - Adaptive rate mode at initialization dynamicRa(3) - Dynamic rate adaptation sosEnabled(4) - SOS enabled
Status: current Access: read-only
OBJECT-TYPE    
  Xdsl2StatusActualRaMode  

vdslChanRetransmissionMode 1.1.890.1.5.13.5.13.8.10.1.3
RTX-USED operational data parameter. The possible values are: rtxInUse(1) - RTX in use. rtxForbidden(2) - RTX not in use because RTX-MODE = FORBIDDEN. rtxNotSupportedXtuC(3) - RTX not in use because it is not supported by the XTU-C. rtxNotSupportedXtuR(4) - RTX not in use because it is not supported by the XTU-R. rtxNotSupportedBoth(5) - RTX not in use because it is not supported by the XTU-C and XTU-R.
Status: current Access: read-only
OBJECT-TYPE    
  Xdsl2StatusRtxMode  

vdslChanRetransmissionOverhead 1.1.890.1.5.13.5.13.8.10.1.4
Expected retransmission overhead in G.inp due to REIN and SHINE noise. Unit is kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcSessionTable 1.1.890.1.5.13.5.13.9.1
This table shows the paepvc session statistics. This table is supported by R1.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PaepvcSessionEntry

paepvcSessionEntry 1.1.890.1.5.13.5.13.9.1.1
An entry of paepvcSessionTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PaepvcSessionEntry  

paepvcSessionVpi 1.1.890.1.5.13.5.13.9.1.1.1
The PAEPVC VPI.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

paepvcSessionVci 1.1.890.1.5.13.5.13.9.1.1.2
The PAEPVC VCI.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

paepvcSessionState 1.1.890.1.5.13.5.13.9.1.1.3
The PAEPVC status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(1), pppoe(2), ppp(3), up(4)  

paepvcSessionId 1.1.890.1.5.13.5.13.9.1.1.4
The PAEPVC session ID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

paepvcSessionUpTime 1.1.890.1.5.13.5.13.9.1.1.5
The PAEPVC session uptime.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcSessionAcName 1.1.890.1.5.13.5.13.9.1.1.6
Access concentrator name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

paepvcSessionSrvcName 1.1.890.1.5.13.5.13.9.1.1.7
Service name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

paepvcCountTable 1.1.890.1.5.13.5.13.9.2
This table shows the paepvc counters. This table is supported by R1.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PaepvcCountEntry

paepvcCountEntry 1.1.890.1.5.13.5.13.9.2.1
An entry of paepvcCountTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  PaepvcCountEntry  

paepvcCountVpi 1.1.890.1.5.13.5.13.9.2.1.1
The PAEPVC VPI.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

paepvcCountVci 1.1.890.1.5.13.5.13.9.2.1.2
The PAEPVC VCI.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

paepvcCountPppLcpCfgReqRx 1.1.890.1.5.13.5.13.9.2.1.3
The number of ppp lcp config-request received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountPppLcpEchoReqRx 1.1.890.1.5.13.5.13.9.2.1.4
The number of ppp lcp echo-request received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountPppLcpEchoReplyRx 1.1.890.1.5.13.5.13.9.2.1.5
The number of ppp lcp echo-reply received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountPadiTx 1.1.890.1.5.13.5.13.9.2.1.6
The number of pppoe padi transfered.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountPadoRx 1.1.890.1.5.13.5.13.9.2.1.7
The number of pppoe pado received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountPadrTx 1.1.890.1.5.13.5.13.9.2.1.8
The number of pppoe padr received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountPadsRx 1.1.890.1.5.13.5.13.9.2.1.9
The number of pppoe pads received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountPadtTx 1.1.890.1.5.13.5.13.9.2.1.10
The number of pppoe padt transfered.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountPadtRx 1.1.890.1.5.13.5.13.9.2.1.11
The number of pppoe padt received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountSrvcnameErrRx 1.1.890.1.5.13.5.13.9.2.1.12
The number of pppoe service name error received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountAcnameErrRx 1.1.890.1.5.13.5.13.9.2.1.13
The number of pppoe access concentrator name error received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountGenericErrTx 1.1.890.1.5.13.5.13.9.2.1.14
The number of pppoe generic error transfered.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

paepvcCountGenericErrRx 1.1.890.1.5.13.5.13.9.2.1.15
The number of pppoe generic error received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vlanMacDisplayTarget 1.1.890.1.5.13.5.13.10.1
This managed object is a filter used for identify the target from which the MAC addresses are learned in macTable. Ifindex is used to specify a specific interface of which the MAC addresses are displayed. Some values are reserved for special purpose, they are: 0: All interfaces 50: All uplink ports
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

vlanMacDisplayVid 1.1.890.1.5.13.5.13.10.2
This object is supported by R1.03 and later versions. This managed object is a filter used for identifying the target from which the MAC addresses are learned in vlanMacTable. The value of zero means no filtering.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

vlanMacTable 1.1.890.1.5.13.5.13.10.3
This table is supported by R1.03 and later versions. A table that contains information about unicast entries for which the bridge has forwarding and/or filtering information. This information is used by the transparent bridging function in determining how to propagate a received frame.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VlanMacEntry

vlanMacEntry 1.1.890.1.5.13.5.13.10.3.1
An entry of vlanMacTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VlanMacEntry  

vlanMacAddress 1.1.890.1.5.13.5.13.10.3.1.1
A unicast MAC address for which the bridge has forwarding and/or filtering information.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

vlanMacPort 1.1.890.1.5.13.5.13.10.3.1.2
The port from which the mac address has been learned.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vlanMacStatus 1.1.890.1.5.13.5.13.10.3.1.3
The status of this entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), invalid(2), learned(3), self(4), mgmt(5)  

arpproxyTable 1.1.890.1.5.13.5.13.11.1
Display ARP table. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ArpproxyEntry

arpproxyEntry 1.1.890.1.5.13.5.13.11.1.1
An entry of arpproxyTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ArpproxyEntry  

arpproxyIp 1.1.890.1.5.13.5.13.11.1.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

arpproxyMac 1.1.890.1.5.13.5.13.11.1.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

arpproxyIfIndex 1.1.890.1.5.13.5.13.11.1.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

arpproxyVpi 1.1.890.1.5.13.5.13.11.1.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

arpproxyVci 1.1.890.1.5.13.5.13.11.1.1.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

arpproxyInterfaceIp 1.1.890.1.5.13.5.13.11.1.1.6
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

arpproxyInterfaceMask 1.1.890.1.5.13.5.13.11.1.1.7
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

arpproxyInterfaceVid 1.1.890.1.5.13.5.13.11.1.1.8
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

arpproxyDhcpIp 1.1.890.1.5.13.5.13.11.1.1.9
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

arpproxyType 1.1.890.1.5.13.5.13.11.1.1.10
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER upstream(1), downstream(2)  

ipbpvcIfDynamicTable 1.1.890.1.5.13.5.13.11.2
Display runtime interfaces. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpbpvcIfDynamicEntry

ipbpvcIfDynamicEntry 1.1.890.1.5.13.5.13.11.2.1
An entry of ipbpvcIfDynamicTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpbpvcIfDynamicEntry  

ipbpvcIfDynamicIp 1.1.890.1.5.13.5.13.11.2.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

ipbpvcIfDynamicMask 1.1.890.1.5.13.5.13.11.2.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcIfDynamicIfIndex 1.1.890.1.5.13.5.13.11.2.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcIfDynamicVpi 1.1.890.1.5.13.5.13.11.2.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcIfDynamicVci 1.1.890.1.5.13.5.13.11.2.1.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcRouteDynamicTable 1.1.890.1.5.13.5.13.11.3
Display runtime routing table. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IpbpvcRouteDynamicEntry

ipbpvcRouteDynamicEntry 1.1.890.1.5.13.5.13.11.3.1
An entry of ipbpvcRouteDynamicTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IpbpvcRouteDynamicEntry  

ipbpvcRouteDynamicType 1.1.890.1.5.13.5.13.11.3.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER upstream(1), downstream(2)  

ipbpvcRouteDynamicIp 1.1.890.1.5.13.5.13.11.3.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

ipbpvcRouteDynamicMask 1.1.890.1.5.13.5.13.11.3.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcRouteDynamicNextHop 1.1.890.1.5.13.5.13.11.3.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

ipbpvcRouteDynamicMetric 1.1.890.1.5.13.5.13.11.3.1.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ipbpvcRouteDynamicPriority 1.1.890.1.5.13.5.13.11.3.1.6
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipLineStatusTable 1.1.890.1.5.13.5.13.12.1
The table displays VoIP line status. This table is supported by R4.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipLineStatusEntry

voipLineStatusEntry 1.1.890.1.5.13.5.13.12.1.1
An entry of voipLineStatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipLineStatusEntry  

voipLineStatusFxsStatus 1.1.890.1.5.13.5.13.12.1.1.1
FXS status of the line.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), on-hook(2), off-hook(3), ringing(4), power-cut-down(5), testing(6), fault(7), bad(8), uninitialized(9)  

voipLineStatusServiceStatus 1.1.890.1.5.13.5.13.12.1.1.2
Service status of the line.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), out-of-service(2), idle(3), waiting-for-dialing(4), dialing-out(5), ringing(6), conversation-caller(7), conversation-callee(8), fax-caller(9), fax-callee(10), modem-caller(11), modem-callee(12), waiting-for-on-hook(13), dialing-timeout(14), alerting-off-hook(15), power-cut-down(16)  

voipLineInfoTable 1.1.890.1.5.13.5.13.12.2
The table displays VoIP line information. This table is supported by R4.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipLineInfoEntry

voipLineInfoEntry 1.1.890.1.5.13.5.13.12.2.1
An entry of voipLineInfoTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipLineInfoEntry  

voipLineInfoSipLocalUri 1.1.890.1.5.13.5.13.12.2.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipLineInfoSipRemoteUri 1.1.890.1.5.13.5.13.12.2.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipLineInfoRtpTxCodecType 1.1.890.1.5.13.5.13.12.2.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipLineInfoRtpRxCodecType 1.1.890.1.5.13.5.13.12.2.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipLineInfoRtpTxPt 1.1.890.1.5.13.5.13.12.2.1.5
1: g711mu(0) 2: g711a(8) 3: g723(4) 4: g729(18) 5: g726-16(96) 6: g726-24(97) 7: g728-32(98) 8: g728-40(99)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipLineInfoRtpRxPt 1.1.890.1.5.13.5.13.12.2.1.6
1: g711mu(0) 2: g711a(8) 3: g723(4) 4: g729(18) 5: g726-16(96) 6: g726-24(97) 7: g728-32(98) 8: g728-40(99)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipLineInfoRtpLocalIp 1.1.890.1.5.13.5.13.12.2.1.7
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipLineInfoRtpRemoteIp 1.1.890.1.5.13.5.13.12.2.1.8
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipLineInfoRtpLocalPort 1.1.890.1.5.13.5.13.12.2.1.9
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipLineInfoRtpRemotePort 1.1.890.1.5.13.5.13.12.2.1.10
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipLineInfoLastCidMode 1.1.890.1.5.13.5.13.12.2.1.11
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), fsk(1), dtmf(2)  

voipLineInfoPlaySignalTel 1.1.890.1.5.13.5.13.12.2.1.12
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), dial-tone(1), ringback-tone(2), busy-tone(3), congestion-tone(4), special-dial-tone(5), warning-tone(6), beep-tone(7), call-waiting-tone1(8), howler-tone(9), confirmation-tone(10), holding-tone(11), mwi-tone(12), enable-dtmf-detect(13), disable-dtmf-detect(14), mute(15), call-waiting-tone2(16), dtmf-tone(17), recall-dial-tone(18), stop-ring(19), ring(20)  

voipLineInfoPlaySignalNet 1.1.890.1.5.13.5.13.12.2.1.13
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), dial-tone(1), ringback-tone(2), busy-tone(3), congestion-tone(4), special-dial-tone(5), warning-tone(6), beep-tone(7), call-waiting-tone1(8), howler-tone(9), confirmation-tone(10), holding-tone(11), mwi-tone(12), enable-dtmf-detect(13), disable-dtmf-detect(14), mute(15), call-waiting-tone2(16), dtmf-tone(17), recall-dial-tone(18), stop-ring(19), ring(20)  

voipH248StatTable 1.1.890.1.5.13.5.13.12.3
The table displays registration status of media gateway. This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipH248StatEntry

voipH248StatEntry 1.1.890.1.5.13.5.13.12.3.1
An entry of voipH248StatTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipH248StatEntry  

voipH248StatSlot 1.1.890.1.5.13.5.13.12.3.1.1
Line card slot number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248StatMgName 1.1.890.1.5.13.5.13.12.3.1.2
MG name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipH248StatMgState 1.1.890.1.5.13.5.13.12.3.1.3
MG state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), registering(2), registered(3), unregistering(4), unregistered(5), inactivity-timeout(6), activity-back(7), disconnected(8), disabled-by-mgc(9), unknown(10)  

voipSipStatTable 1.1.890.1.5.13.5.13.12.4
The table displays the status of SIP proxy server while oolocal calloo feature is enabled. This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipSipStatEntry

voipSipStatEntry 1.1.890.1.5.13.5.13.12.4.1
An entry of voipSipStatTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipSipStatEntry  

voipSipStatSlot 1.1.890.1.5.13.5.13.12.4.1.1
Line card slot number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipSipStatProxyIndex 1.1.890.1.5.13.5.13.12.4.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipSipStatProxySvr 1.1.890.1.5.13.5.13.12.4.1.3
Proxy server IP or proxy server doamin name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipSipStatProxyPort 1.1.890.1.5.13.5.13.12.4.1.4
Proxy server port.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipSipStatState 1.1.890.1.5.13.5.13.12.4.1.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER lost(1), alive(2), unknown(3)  

voipH248InterfaceStatTable 1.1.890.1.5.13.5.13.12.5
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipH248InterfaceStatEntry

voipH248InterfaceStatEntry 1.1.890.1.5.13.5.13.12.5.1
An entry of voipH248InterfaceStatTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipH248InterfaceStatEntry  

voipH248InterfaceStatId 1.1.890.1.5.13.5.13.12.5.1.1
Line card slot number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248InterfaceStatMgState 1.1.890.1.5.13.5.13.12.5.1.2
Mg State
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(1), registering(2), registered(3), unregistering(4), unregistered(5), inactivity-timeout(6), activity-back(7), disconnected(8), disabled-by-MGC(9)  

voipH248InterfaceStatPrimarySlot 1.1.890.1.5.13.5.13.12.5.1.3
Primary Slot
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248InterfaceStatSecondarySlot 1.1.890.1.5.13.5.13.12.5.1.4
Secondary Slot
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248InterfaceStatPrimaryProtectionState 1.1.890.1.5.13.5.13.12.5.1.5
Primary Protection State
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER invalid(1), active(2), standby(3)  

voipH248InterfaceStatSecondaryProtectionState 1.1.890.1.5.13.5.13.12.5.1.6
Secondary Protection State
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER invalid(1), active(2), standby(3)  

voipH248InterfaceStatRedundantState 1.1.890.1.5.13.5.13.12.5.1.7
Redundant State
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER out-of-sync(1), authorization(2), synchronizing(3), in-service(4)  

voipH248MediaStatTable 1.1.890.1.5.13.5.13.12.6
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipH248MediaStatEntry

voipH248MediaStatEntry 1.1.890.1.5.13.5.13.12.6.1
An entry of voipH248MediaStatTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipH248MediaStatEntry  

voipH248MediaStatInterfaceId 1.1.890.1.5.13.5.13.12.6.1.1
Interface ID.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248MediaStatSlaveId 1.1.890.1.5.13.5.13.12.6.1.2
Media ID
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248MediaStatSlaveIp 1.1.890.1.5.13.5.13.12.6.1.3
Media Ip
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248MediaStatMgmtInbandIp 1.1.890.1.5.13.5.13.12.6.1.4
Management Inband Ip
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248MediaStatMgmtOutbandIp 1.1.890.1.5.13.5.13.12.6.1.5
Management Onband Ip
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248MediaStatSlotId 1.1.890.1.5.13.5.13.12.6.1.6
slot id
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248MediaStatPortCount 1.1.890.1.5.13.5.13.12.6.1.7
port count
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248MediaStatState 1.1.890.1.5.13.5.13.12.6.1.8
state
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unregistered(1), registered(2), invalid(3), unknown(4)  

voipH248TerminationStatTable 1.1.890.1.5.13.5.13.12.7
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipH248TerminationStatEntry

voipH248TerminationStatEntry 1.1.890.1.5.13.5.13.12.7.1
An entry of voipH248TerminationStatStateTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipH248TerminationStatEntry  

voipH248TerminationStatStateId 1.1.890.1.5.13.5.13.12.7.1.1
Interface Id of the termination.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248TerminationStatStateMediaId 1.1.890.1.5.13.5.13.12.7.1.2
Media Card Id of the termination.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248TerminationStatStatePortNumber 1.1.890.1.5.13.5.13.12.7.1.3
Port number the termination.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248TerminationStatName 1.1.890.1.5.13.5.13.12.7.1.4
Termination Name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipH248TerminationStatPhoneState 1.1.890.1.5.13.5.13.12.7.1.5
Phone State
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), on-hook(2), off-hook(3), ringing(4), testing(5), power-cut-down(6), fault(7), bad(8), uninitialized(9), unknown(10)  

voipH248TerminationStatCallServiceState 1.1.890.1.5.13.5.13.12.7.1.6
Call Service State
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), out-of-service(2), idle(3), waiting-for-dialing(4), dialing-out(5), ringing(6), conversation-caller(7), conversation-callee(8), fax-modem-caller(9), fax-modem-callee(10), waiting-for-on-hook(13), dialing-timeout(14), alerting-off-hook(15), power-cut-down(16), unknown(17)  

voipH248TerminationStatQuery 1.1.890.1.5.13.5.13.12.8
OBJECT IDENTIFIER    

voipH248TerminationStatQueryInterfaceId 1.1.890.1.5.13.5.13.12.8.1
Interface Id
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipH248TerminationStatQueryTerminationName 1.1.890.1.5.13.5.13.12.8.2
Termination Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipH248TerminationStatQuerySlaveId 1.1.890.1.5.13.5.13.12.8.3
Slave Id
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248TerminationStatQuerySlaveIp 1.1.890.1.5.13.5.13.12.8.4
Slave Ip
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipH248TerminationStatQueryMgmtInbandIp 1.1.890.1.5.13.5.13.12.8.5
Management Inband Ip
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipH248TerminationStatQueryMgmtOutbandIp 1.1.890.1.5.13.5.13.12.8.6
Management Outband Ip
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipH248TerminationStatQuerySlotId 1.1.890.1.5.13.5.13.12.8.7
Slot Id
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248TerminationStatQueryPortCount 1.1.890.1.5.13.5.13.12.8.8
Port Count
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248TerminationStatQueryState 1.1.890.1.5.13.5.13.12.8.9
State
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unregistered(1), registered(2), invalid(3), unknown(4)  

voipH248TerminationStatQueryPortNumber 1.1.890.1.5.13.5.13.12.8.10
Port Number
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248TerminationStatQueryPhoneState 1.1.890.1.5.13.5.13.12.8.11
Phone State
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), on-hook(2), off-hook(3), ringing(4), testing(5), power-cut-down(6), fault(7), bad(8), uninitialized(9), unknown(10)  

voipH248TerminationStatQueryCallServiceState 1.1.890.1.5.13.5.13.12.8.12
CallService State
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), out-of-service(2), idle(3), waiting-for-dialing(4), ringing(5), conversation-caller(6), conversation-callee(7), fax-modem-caller(8), fax-modem-callee(9), waiting-for-on-hook(12), dialing-timeout(13), alerting-off-hook(14), power-cut-down(15)  

voipRtpStatTable 1.1.890.1.5.13.5.13.12.9
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipRtpStatEntry

voipRtpStatEntry 1.1.890.1.5.13.5.13.12.9.1
An entry of voipRtpStatTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipRtpStatEntry  

voipRtpStatTxRate 1.1.890.1.5.13.5.13.12.9.1.1
real-time RTP tx packet rate in bps.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipRtpStatRxRate 1.1.890.1.5.13.5.13.12.9.1.2
real-time RTP rx packet rate in bps.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipRtpStatTxPktCnt 1.1.890.1.5.13.5.13.12.9.1.3
total RTP tx packet counter for current/last call.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

voipRtpStatRxPktCnt 1.1.890.1.5.13.5.13.12.9.1.4
total RTP rx packet counter for current/last call.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

voipRtpStatTxFracLost 1.1.890.1.5.13.5.13.12.9.1.5
RTP Tx packet lost in percentage
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipRtpStatRxFracLost 1.1.890.1.5.13.5.13.12.9.1.6
RTP Rx packet lost in percentage
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipRtpStatTxJitter 1.1.890.1.5.13.5.13.12.9.1.7
TX jitter in micro-second
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

voipRtpStatRxJitter 1.1.890.1.5.13.5.13.12.9.1.8
Rx jitter in micro-second
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

voipRtpStatTxAvgDelay 1.1.890.1.5.13.5.13.12.9.1.9
Average Tx delay in ms
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

voipRtpStatRxAvgDelay 1.1.890.1.5.13.5.13.12.9.1.10
Average Rx delay in ms
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

voipCdrStat 1.1.890.1.5.13.5.13.12.10
OBJECT IDENTIFIER    

voipCdrStatFilter 1.1.890.1.5.13.5.13.12.10.1
OBJECT IDENTIFIER    

voipCdrStatFilterInterface 1.1.890.1.5.13.5.13.12.10.1.1
Interface id.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipCdrStatFilterIndexEnable 1.1.890.1.5.13.5.13.12.10.1.2
Set 0 to clear voipCdrStatFilterIndex. It will show 1 if voipCdrStatFilterIndex had been set before.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipCdrStatFilterIndex 1.1.890.1.5.13.5.13.12.10.1.3
Index filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipCdrStatFilterSlotPortEnable 1.1.890.1.5.13.5.13.12.10.1.4
Set 0 to clear voipCdrStatFilterSlot and voipCdrStatFilterPort. It will show 1 if voipCdrStatFilterSlot and voipCdrStatFilterPort had been set before.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipCdrStatFilterSlot 1.1.890.1.5.13.5.13.12.10.1.5
Slot filter.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipCdrStatFilterPort 1.1.890.1.5.13.5.13.12.10.1.6
Port filter, 0 mean select all port
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipCdrStatFilterRtpElpasedTimeEnable 1.1.890.1.5.13.5.13.12.10.1.7
Set 0 to clear voipCdrStatFilterRtpElpasedTimeMin and voipCdrStatFilterRtpElpasedTimeMax. It will show 1 if any of them had been set before.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipCdrStatFilterRtpElpasedTimeMin 1.1.890.1.5.13.5.13.12.10.1.8
in unit of second
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipCdrStatFilterRtpElpasedTimeMax 1.1.890.1.5.13.5.13.12.10.1.9
in unit of second
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipCdrStatFilterTelEnable 1.1.890.1.5.13.5.13.12.10.1.10
Set 0 to clear voipCdrStatFilterTel. It will show 1 if voipCdrStatFilterTel had been set before.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipCdrStatFilterTel 1.1.890.1.5.13.5.13.12.10.1.11
Telephone number filter, max length is 24.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

voipCdrStatFilterOffhookEnable 1.1.890.1.5.13.5.13.12.10.1.12
Set 0 to clear voipCdrStatFilterOffhookDateMin, voipCdrStatFilterOffhookTimeMin, voipCdrStatFilterOffhookDateMax, and voipCdrStatFilterOffhookDateMax . It will show 1 if any of them had been set before.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipCdrStatFilterOffhookDateMin 1.1.890.1.5.13.5.13.12.10.1.13
Minimum offhook date filter, format example:20120101
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipCdrStatFilterOffhookTimeMin 1.1.890.1.5.13.5.13.12.10.1.14
Minimum offhook time filter, format example:235959
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipCdrStatFilterOffhookDateMax 1.1.890.1.5.13.5.13.12.10.1.15
Maximum offhook date filter, format example:20120101
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipCdrStatFilterOffhookTimeMax 1.1.890.1.5.13.5.13.12.10.1.16
Maximum offhook time filter, format example:235959
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipCdrStatFilterCodeEnable 1.1.890.1.5.13.5.13.12.10.1.17
Set 0 to clear voipCdrStatFilterCode. It will show 1 if voipCdrStatFilterCode had been set before.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipCdrStatFilterCode 1.1.890.1.5.13.5.13.12.10.1.18
Code filter. It is a bit map of the call state record. bit 6(0x20): offhook bit 5(0x10): remote ringback tone bit 4(0x08): local ringback tone bit 3(0x04): dial tone bit 2(0x02): ring bit 1(0x01): rtp
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipCdrStatFilterErrCodeEnable 1.1.890.1.5.13.5.13.12.10.1.19
Set 1 to ebable H.248 errcode filter. Set 0 to disable it.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipCdrStatResultTable 1.1.890.1.5.13.5.13.12.10.2
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipCdrStatResultEntry

voipCdrStatResultEntry 1.1.890.1.5.13.5.13.12.10.2.1
An entry of voipCdrStatResultTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipCdrStatResultEntry  

voipCdrStatResultIndex 1.1.890.1.5.13.5.13.12.10.2.1.1
Index of record. Index of the newest record will show first.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipCdrStatResultSlot 1.1.890.1.5.13.5.13.12.10.2.1.2
Record Slot
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipCdrStatResultPort 1.1.890.1.5.13.5.13.12.10.2.1.3
Record port
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipCdrStatResultTermName 1.1.890.1.5.13.5.13.12.10.2.1.4
The termination name used for this record.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipCdrStatResultLineDirection 1.1.890.1.5.13.5.13.12.10.2.1.5
1: Call in 2: Dial out
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipCdrStatResultLocalNumber 1.1.890.1.5.13.5.13.12.10.2.1.6
The local phone number set by manager and use for localcall
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipCdrStatResultRemoteNumber 1.1.890.1.5.13.5.13.12.10.2.1.7
The remote phone number which assigned by mgc
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipCdrStatResultOffHookDatetime 1.1.890.1.5.13.5.13.12.10.2.1.8
In format YYYYMMDDhhmmss
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipCdrStatResultOnHookDatetime 1.1.890.1.5.13.5.13.12.10.2.1.9
In format YYYYMMDDhhmmss
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipCdrStatResultRingStartDatetime 1.1.890.1.5.13.5.13.12.10.2.1.10
In format YYYYMMDDhhmmss
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipCdrStatResultRingStopDatetime 1.1.890.1.5.13.5.13.12.10.2.1.11
In format YYYYMMDDhhmmss
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipCdrStatResultRtpStartDatetime 1.1.890.1.5.13.5.13.12.10.2.1.12
In format YYYYMMDDhhmmss
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipCdrStatResultRtpStopDatetime 1.1.890.1.5.13.5.13.12.10.2.1.13
In format YYYYMMDDhhmmss
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipCdrStatResultRtpElapsedTime 1.1.890.1.5.13.5.13.12.10.2.1.14
In unit of second
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipCdrStatResultTxRate 1.1.890.1.5.13.5.13.12.10.2.1.15
real-time RTP tx packet rate in bps
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipCdrStatResultRxRate 1.1.890.1.5.13.5.13.12.10.2.1.16
real-time RTP rx packet rate in bps
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipCdrStatResultTxPktCnt 1.1.890.1.5.13.5.13.12.10.2.1.17
total RTP tx packet counter
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

voipCdrStatResultRxPktCnt 1.1.890.1.5.13.5.13.12.10.2.1.18
total RTP rx packet counter
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

voipCdrStatResultTxFracLost 1.1.890.1.5.13.5.13.12.10.2.1.19
RTP tx packet lost in percentage
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipCdrStatResultRxFracLost 1.1.890.1.5.13.5.13.12.10.2.1.20
RTP rx packet lost in percentage
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipCdrStatResultTxJitter 1.1.890.1.5.13.5.13.12.10.2.1.21
Tx Jitter in micro-second
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

voipCdrStatResultRxJitter 1.1.890.1.5.13.5.13.12.10.2.1.22
Rx Jitter in micro-second
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

voipCdrStatResultTxAvgDelay 1.1.890.1.5.13.5.13.12.10.2.1.23
Average tx delay in ms
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

voipCdrStatResultRxAvgDelay 1.1.890.1.5.13.5.13.12.10.2.1.24
Average rx delay in ms
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

voipCdrStatResultCode 1.1.890.1.5.13.5.13.12.10.2.1.25
Bit map of the call state record. bit 6(0x20): offhook bit 5(0x10): remote ringback tone bit 4(0x08): local ringback tone bit 3(0x04): dial tone bit 2(0x02): ring bit 1(0x01): rtp
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipCdrStatResultErrCode 1.1.890.1.5.13.5.13.12.10.2.1.26
Errcode of H.248 protocol. 0 mean no error.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipCdrStatResultTerminationCause 1.1.890.1.5.13.5.13.12.10.2.1.27
Termination Cause
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipH248Statistics 1.1.890.1.5.13.5.13.12.11
OBJECT IDENTIFIER    

voipH248StatisticsInterface 1.1.890.1.5.13.5.13.12.11.1
Interface id.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipH248StatisticsMsgSent 1.1.890.1.5.13.5.13.12.11.2
Number of sent protocol message, include reset and error.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned64  

voipH248StatisticsMsgRecv 1.1.890.1.5.13.5.13.12.11.3
Number of received message.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned64  

voipH248StatisticsMsgLost 1.1.890.1.5.13.5.13.12.11.4
Number of message without reply.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

voipH248StatisticsMsgResent 1.1.890.1.5.13.5.13.12.11.5
Number of resent message.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

voipH248StatisticsErrorMsg 1.1.890.1.5.13.5.13.12.11.6
Number of error message sent.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

voipH248StatisticsUnIdentifiedMsg 1.1.890.1.5.13.5.13.12.11.7
Number of parse fail message.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

enetPortStatusTable 1.1.890.1.5.13.5.13.13.1
The table displays ethernet port status.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnetPortStatusEntry

enetPortStatusEntry 1.1.890.1.5.13.5.13.13.1.1
An entry of enetPortStatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  EnetPortStatusEntry  

enetPortStatusLinkUpType 1.1.890.1.5.13.5.13.13.1.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(0), copper(1), fiber(2)  

enetPortStatusLinkUpTime 1.1.890.1.5.13.5.13.13.1.1.2
The time since the enet port up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

enetPortStatusLinkSpeed 1.1.890.1.5.13.5.13.13.1.1.3
Link speed in Mbps.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

enetPortStatusLinkDuplex 1.1.890.1.5.13.5.13.13.1.1.4
Link full/half duplex.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER full(1), half(2)  

enetPortStatusDataRateTx 1.1.890.1.5.13.5.13.13.1.1.5
TX data rate in kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

enetPortStatusDataRateRx 1.1.890.1.5.13.5.13.13.1.1.6
RX data rate in kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

enetPortStatusDataUtilTx 1.1.890.1.5.13.5.13.13.1.1.7
TX throughput utilization in percentage.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

enetPortStatusDataUtilRx 1.1.890.1.5.13.5.13.13.1.1.8
RX throughput utilization in percentage.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

sfpPortStatusTable 1.1.890.1.5.13.5.13.13.2
The table displays SFP ethernet port status. This table is supported by R5.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SfpPortStatusEntry

sfpPortStatusEntry 1.1.890.1.5.13.5.13.13.2.1
An entry of sfpPortStatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SfpPortStatusEntry  

sfpId 1.1.890.1.5.13.5.13.13.2.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

sfpConnector 1.1.890.1.5.13.5.13.13.2.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

sfpTransceiver 1.1.890.1.5.13.5.13.13.2.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

sfpEncoding 1.1.890.1.5.13.5.13.13.2.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

sfpName 1.1.890.1.5.13.5.13.13.2.1.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

sfpPartNumber 1.1.890.1.5.13.5.13.13.2.1.6
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

sfpRevision 1.1.890.1.5.13.5.13.13.2.1.7
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

sfpSerialNumber 1.1.890.1.5.13.5.13.13.2.1.8
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

sfpTemperature 1.1.890.1.5.13.5.13.13.2.1.9
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sfpSupplyVoltage 1.1.890.1.5.13.5.13.13.2.1.10
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sfpTxBiasCurrent 1.1.890.1.5.13.5.13.13.2.1.11
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sfpTxPower 1.1.890.1.5.13.5.13.13.2.1.12
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sfpRxPower 1.1.890.1.5.13.5.13.13.2.1.13
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

ifStatusTable 1.1.890.1.5.13.5.13.14.1
The table displays port interface status. This table is supported by R5.02 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    IfStatusEntry

ifStatusEntry 1.1.890.1.5.13.5.13.14.1.1
An entry of ifStatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  IfStatusEntry  

ifInRate 1.1.890.1.5.13.5.13.14.1.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ifOutRate 1.1.890.1.5.13.5.13.14.1.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ifCurrentStatus 1.1.890.1.5.13.5.13.14.1.1.3
Current status of an interface
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3), unknown(4), blocked(5)  

ifUpTime 1.1.890.1.5.13.5.13.14.1.1.4
The time since the line link up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

imaPvcStatsTable 1.1.890.1.5.13.5.13.15.1
The table displays IMA Group PVC status. This table is supported by R5.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ImaPvcStatsEntry

imaPvcStatsEntry 1.1.890.1.5.13.5.13.15.1.1
An entry of imaPvcStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ImaPvcStatsEntry  

imaPvcStatsGroupIndex 1.1.890.1.5.13.5.13.15.1.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaPvcStatsVpi 1.1.890.1.5.13.5.13.15.1.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaPvcStatsVci 1.1.890.1.5.13.5.13.15.1.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaPvcStatsTxPackets 1.1.890.1.5.13.5.13.15.1.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

imaPvcStatsRxPackets 1.1.890.1.5.13.5.13.15.1.1.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

imaPvcStatsTxUnicast 1.1.890.1.5.13.5.13.15.1.1.6
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

imaPvcStatsRxUnicast 1.1.890.1.5.13.5.13.15.1.1.7
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

imaPvcStatsTxMulticast 1.1.890.1.5.13.5.13.15.1.1.8
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

imaPvcStatsRxMulticast 1.1.890.1.5.13.5.13.15.1.1.9
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

imaPvcStatsTxBroadcast 1.1.890.1.5.13.5.13.15.1.1.10
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

imaPvcStatsRxBroadcast 1.1.890.1.5.13.5.13.15.1.1.11
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

imaPvcStatsTxDiscard 1.1.890.1.5.13.5.13.15.1.1.12
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

imaPvcStatsRxDiscard 1.1.890.1.5.13.5.13.15.1.1.13
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

imaGroupStatsTable 1.1.890.1.5.13.5.13.15.2
The table displays IMA Group status. This table is supported by R5.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ImaGroupStatsEntry

imaGroupStatsEntry 1.1.890.1.5.13.5.13.15.2.1
An entry of imaGroupStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ImaGroupStatsEntry  

imaGroupStatsGroupIndex 1.1.890.1.5.13.5.13.15.2.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaGroupStatsTxCells 1.1.890.1.5.13.5.13.15.2.1.2
Tx Cells since reset
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

imaGroupStatsRxCells 1.1.890.1.5.13.5.13.15.2.1.3
Rx Cells since reset
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

imaGroupStatsTxRate 1.1.890.1.5.13.5.13.15.2.1.4
Tx data rate in Bytes/s
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaGroupStatsRxRate 1.1.890.1.5.13.5.13.15.2.1.5
Rx data rate in Bytes/s
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaGroupStatsCrcErr 1.1.890.1.5.13.5.13.15.2.1.6
CRC errors since reset
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

imaGroupCurrDayTable 1.1.890.1.5.13.5.13.15.3
The table displays IMA Group Current Day Counters. This table is supported by R5.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ImaGroupCurrDayEntry

imaGroupCurrDayEntry 1.1.890.1.5.13.5.13.15.3.1
An entry of imaGroupCurrDayTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ImaGroupCurrDayEntry  

imaGroupCurrDayGroupIndex 1.1.890.1.5.13.5.13.15.3.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaGroupCurrDayUnavailSecs 1.1.890.1.5.13.5.13.15.3.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaGroupCurrDayNeNumFailures 1.1.890.1.5.13.5.13.15.3.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaGroupCurrDayFeNumFailures 1.1.890.1.5.13.5.13.15.3.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaLinkCurrDayTable 1.1.890.1.5.13.5.13.15.4
The table displays IMA Link Current Day Counters. This table is supported by R5.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ImaLinkCurrDayEntry

imaLinkCurrDayEntry 1.1.890.1.5.13.5.13.15.4.1
An entry of imaLinkCurrDayTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ImaLinkCurrDayEntry  

imaLinkCurrDayIfindex 1.1.890.1.5.13.5.13.15.4.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaLinkCurrDayImaViolations 1.1.890.1.5.13.5.13.15.4.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaLinkCurrDayOifAnomalies 1.1.890.1.5.13.5.13.15.4.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaLinkCurrDayNeSevErroredSecs 1.1.890.1.5.13.5.13.15.4.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaLinkCurrDayFeSevErroredSecs 1.1.890.1.5.13.5.13.15.4.1.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaLinkCurrDayNeUnavailSecs 1.1.890.1.5.13.5.13.15.4.1.6
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaLinkCurrDayFeUnavailSecs 1.1.890.1.5.13.5.13.15.4.1.7
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaLinkCurrDayNeTxUnusableSecs 1.1.890.1.5.13.5.13.15.4.1.8
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaLinkCurrDayNeRxUnusableSecs 1.1.890.1.5.13.5.13.15.4.1.9
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaLinkCurrDayFeTxUnusableSecs 1.1.890.1.5.13.5.13.15.4.1.10
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaLinkCurrDayFeRxUnusableSecs 1.1.890.1.5.13.5.13.15.4.1.11
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaLinkCurrDayNeTxNumFailures 1.1.890.1.5.13.5.13.15.4.1.12
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaLinkCurrDayNeRxNumFailures 1.1.890.1.5.13.5.13.15.4.1.13
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaLinkCurrDayFeTxNumFailures 1.1.890.1.5.13.5.13.15.4.1.14
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaLinkCurrDayFeRxNumFailures 1.1.890.1.5.13.5.13.15.4.1.15
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaLinkCurrDayTxStuffs 1.1.890.1.5.13.5.13.15.4.1.16
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaLinkCurrDayRxStuffs 1.1.890.1.5.13.5.13.15.4.1.17
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaGroupConfReadyTable 1.1.890.1.5.13.5.13.15.5
The table displays IMA Group Configuration Ready status. This table is supported by R5.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ImaGroupConfReadyEntry

imaGroupConfReadyEntry 1.1.890.1.5.13.5.13.15.5.1
An entry of imaGroupConfReadyTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ImaGroupConfReadyEntry  

imaGroupConfReadyIndex 1.1.890.1.5.13.5.13.15.5.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaGroupConfReadyState 1.1.890.1.5.13.5.13.15.5.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER conf-ready(1), conf-forbidden(2)  

imaGroupStatusTable 1.1.890.1.5.13.5.13.15.6
The table displays IMA Group status. This table is supported by R5.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ImaGroupStatusEntry

imaGroupStatusEntry 1.1.890.1.5.13.5.13.15.6.1
An entry of imaGroupConfReadyTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ImaGroupStatusEntry  

imaGroupStatusGroupIndex 1.1.890.1.5.13.5.13.15.6.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaGroupStatusTxPayloadRate 1.1.890.1.5.13.5.13.15.6.1.2
Maximum tx data rate in kbps
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaGroupStatusRxPayloadRate 1.1.890.1.5.13.5.13.15.6.1.3
Maximum rx data rate in kbps
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e1CurrDayTable 1.1.890.1.5.13.5.13.16.1
The table displays E1 Port Current Day Counters. This table is supported by R5.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    E1CurrDayEntry

e1CurrDayEntry 1.1.890.1.5.13.5.13.16.1.1
An entry of e1CurrDayTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  E1CurrDayEntry  

e1CurrDayIfindex 1.1.890.1.5.13.5.13.16.1.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e1CurrDayLCVs 1.1.890.1.5.13.5.13.16.1.1.2
Line Coding Violation
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e1CurrDayPCVs 1.1.890.1.5.13.5.13.16.1.1.3
Path Coding Violation, a.k.a. Error Blocks
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e1CurrDayESs 1.1.890.1.5.13.5.13.16.1.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e1CurrDaySESs 1.1.890.1.5.13.5.13.16.1.1.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e1CurrDayUASs 1.1.890.1.5.13.5.13.16.1.1.6
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e1StatusTable 1.1.890.1.5.13.5.13.16.2
The table displays E1 Port Status. This table is supported by R5.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    E1StatusEntry

e1StatusEntry 1.1.890.1.5.13.5.13.16.2.1
An entry of e1StatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  E1StatusEntry  

e1StatusIfindex 1.1.890.1.5.13.5.13.16.2.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e1StatusTxPayloadRate 1.1.890.1.5.13.5.13.16.2.1.2
Maximum tx data rate in kbps
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e1StatusRxPayloadRate 1.1.890.1.5.13.5.13.16.2.1.3
Maximum rx data rate in kbps
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e1StatusUpTime 1.1.890.1.5.13.5.13.16.2.1.4
The uplink time.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

loopguardStatsTable 1.1.890.1.5.13.5.13.18.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LoopguardStatsEntry

loopguardStatsEntry 1.1.890.1.5.13.5.13.18.1.1
An entry of loopguardStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  LoopguardStatsEntry  

loopguardStatsPort 1.1.890.1.5.13.5.13.18.1.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

loopguardStatsPortStatus 1.1.890.1.5.13.5.13.18.1.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER link-down(0), link-up(1), blocked-by-loopguard(2)  

loopguardStatsLoopguardStatus 1.1.890.1.5.13.5.13.18.1.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

loopguardStatsTotalTxPackets 1.1.890.1.5.13.5.13.18.1.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

loopguardStatsTotalRxPackets 1.1.890.1.5.13.5.13.18.1.1.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

loopguardStatsBadPackets 1.1.890.1.5.13.5.13.18.1.1.6
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

loopguardStatsShutdownTime 1.1.890.1.5.13.5.13.18.1.1.7
seconds
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

stpPortStatsTable 1.1.890.1.5.13.5.13.19.1
The table displays STP Port Status. This table is supported by R5.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    StpPortStatsEntry

stpPortStatsEntry 1.1.890.1.5.13.5.13.19.1.1
An entry of stpPortStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  StpPortStatsEntry  

stpPortStatus 1.1.890.1.5.13.5.13.19.1.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER discarding(1), learning(2), forwarding(3), down(4)  

stpStatsPortNum 1.1.890.1.5.13.5.13.19.2
OBJECT IDENTIFIER    

stpStatsPortNumForwarding 1.1.890.1.5.13.5.13.19.2.1
the number of forwarding ports. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

stpStatsPortNumLearning 1.1.890.1.5.13.5.13.19.2.2
the number of learning ports. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

stpStatsPortNumDiscarding 1.1.890.1.5.13.5.13.19.2.3
the number of discarding ports. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

stpStatsPortNumDown 1.1.890.1.5.13.5.13.19.2.4
the number of link-down ports. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

gbondStatsTable 1.1.890.1.5.13.5.13.20.1
The table displays G.Bond Status. This table is supported by R5.05 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    GbondStatsEntry

gbondStatsEntry 1.1.890.1.5.13.5.13.20.1.1
An entry of gbondStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  GbondStatsEntry  

gbondStatsName 1.1.890.1.5.13.5.13.20.1.1.1
An administratively assigned string, which identifies the bonding group.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

gbondStatsUpRate 1.1.890.1.5.13.5.13.20.1.1.2
The current up stream rate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

gbondStatsDownRate 1.1.890.1.5.13.5.13.20.1.1.3
The current down stream rate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

gbondStatsMember 1.1.890.1.5.13.5.13.20.1.1.4
Indicate if the port is a member port of the bonding group. Each bit in the octet specifies a port from MSB to LSB. for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

gbondStatslinkup 1.1.890.1.5.13.5.13.20.1.1.5
Indicate if the link status of port is bidirectional. Each bit in the octet specifies a port from MSB to LSB. for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

gbondStatsTx 1.1.890.1.5.13.5.13.20.1.1.6
Indicate if the link status of port is Tx only. Each bit in the octet specifies a port from MSB to LSB. for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

gbondStatsRx 1.1.890.1.5.13.5.13.20.1.1.7
Indicate if the link status of port is Rx only. Each bit in the octet specifies a port from MSB to LSB. for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

gbondStatslinkdown 1.1.890.1.5.13.5.13.20.1.1.8
Indicate if the link status of the port is down. Each bit in the octet specifies a port from MSB to LSB. for example: 32(hex) = 50(dec) = 00110010(bin) means the port 3, 4 and 7.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

gbondStatsTCMode 1.1.890.1.5.13.5.13.20.1.1.9
Transmission Convergence layer.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER atm(1), efm(2)  

gbondStatsTxRate 1.1.890.1.5.13.5.13.20.1.1.10
The tx packet rate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

gbondStatsRxRate 1.1.890.1.5.13.5.13.20.1.1.11
The rx packet rate.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslChanExtendedTable 1.1.890.1.5.13.5.13.21.1
The table displays VDSL2 channel Status. This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslChanExtendedEntry

vdslChanExtendedEntry 1.1.890.1.5.13.5.13.21.1.1
An entry of vdslChanExtendedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslChanExtendedEntry  

vdslChanPrevTxRate 1.1.890.1.5.13.5.13.21.1.1.1
Units: kbps
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

vdslChanActualRaMode 1.1.890.1.5.13.5.13.21.1.1.2
The actual RA mode. The possible values are: fixedRateMode(1) - Fixed rate mode raInit(2) - Adaptive rate mode at initialization dynamicRa(3) - Dynamic rate adaptation sosEnabled(4) - SOS enabled
Status: current Access: read-only
OBJECT-TYPE    
  Xdsl2StatusActualRaMode  

vdslChanRetransmissionMode 1.1.890.1.5.13.5.13.21.1.1.3
RTX-USED operational data parameter. The possible values are: rtxInUse(1) - RTX in use. rtxForbidden(2) - RTX not in use because RTX-MODE = FORBIDDEN. rtxNotSupportedXtuC(3) - RTX not in use because it is not supported by the XTU-C. rtxNotSupportedXtuR(4) - RTX not in use because it is not supported by the XTU-R. rtxNotSupportedBoth(5) - RTX not in use because it is not supported by the XTU-C and XTU-R.
Status: current Access: read-only
OBJECT-TYPE    
  Xdsl2StatusRtxMode  

vdslChanRetransmissionOverhead 1.1.890.1.5.13.5.13.21.1.1.4
Expected retransmission overhead in G.inp due to REIN and SHINE noise. Unit is kbps.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslChanGinpFramingType 1.1.890.1.5.13.5.13.21.1.1.5
This parameter is equal to zero if G.inp is not enabled. If G.inp is enabled, it reports the framing type in use (1, 2, 3, or 4).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslChanActualInpAgainstREIN 1.1.890.1.5.13.5.13.21.1.1.6
This parameter reports the actual INP against REIN noise. Unit is 1/2 symbol.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslChanReedSolomonCodeWordPerDtu 1.1.890.1.5.13.5.13.21.1.1.7
This parameter reports the number of RS codewords per DTU. It is equal to D when PhyR is enabled.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslPerfDataExtendedTable 1.1.890.1.5.13.5.13.21.2
The table displays VDSL2 Performance Data. This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslPerfDataExtendedEntry

vdslPerfDataExtendedEntry 1.1.890.1.5.13.5.13.21.2.1
An entry of vdslPerfDataExtendedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslPerfDataExtendedEntry  

vdslPerfDataFECs 1.1.890.1.5.13.5.13.21.2.1.1
Units: kbps
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

vdslChanPerfDataExtendedTable 1.1.890.1.5.13.5.13.21.3
The table displays VDSL2 Channel Performance Data. This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VdslChanPerfDataExtendedEntry

vdslChanPerfDataExtendedEntry 1.1.890.1.5.13.5.13.21.3.1
An entry of vdslPerfDataExtendedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VdslChanPerfDataExtendedEntry  

vdslChanPerfDataCorrectedBlks 1.1.890.1.5.13.5.13.21.3.1.1
Count of all blocks received with errors that were corrected since agent reset. These blocks are passed on as good data. Units: blocks
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslChanPerfDataUncorrectBlks 1.1.890.1.5.13.5.13.21.3.1.2
Count of all blocks received with uncorrectable errors since agent reset. Units: blocks
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vdslChanPerfDataCodeViolations 1.1.890.1.5.13.5.13.21.3.1.3
Count of CRC-8 (FEBE for xTU-R) anomalies occurring in the channel during the interval. This parameter is inhibited during UAS or SES. If the CRC is applied over multiple channels, then each related CRC-8 (or FEBE) anomaly SHOULD increment each of the counters related to the individual channels.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMEx 1.1.890.1.5.13.5.13.21.4
OBJECT IDENTIFIER    

xdsl2PMLineEx 1.1.890.1.5.13.5.13.21.4.1
OBJECT IDENTIFIER    

xdsl2PMLineChannelEx 1.1.890.1.5.13.5.13.21.4.2
OBJECT IDENTIFIER    

xdsl2PMChannelEx 1.1.890.1.5.13.5.13.21.4.3
OBJECT IDENTIFIER    

xdsl2PMLineCurrExtendedTable 1.1.890.1.5.13.5.13.21.4.1.1
The table displays VDSL2 Line Current Performance Data. This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xdsl2PMLineCurrExtendedEntry

xdsl2PMLineCurrExtendedEntry 1.1.890.1.5.13.5.13.21.4.1.1.1
An entry of xdsl2PMLineCurrExtendedEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Xdsl2PMLineCurrExtendedEntry  

xdsl2PMLCurr15MMonitoredTime 1.1.890.1.5.13.5.13.21.4.1.1.1.1
Units: seconds
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

xdsl2PMLCurr15MLofs 1.1.890.1.5.13.5.13.21.4.1.1.1.2
Count of the number of Loss of Framing failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLCurr15MLols 1.1.890.1.5.13.5.13.21.4.1.1.1.3
Count of the number of Loss of Link failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLCurr15MLol 1.1.890.1.5.13.5.13.21.4.1.1.1.4
Count of the number of Loss of Link failures.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLCurr15MLprs 1.1.890.1.5.13.5.13.21.4.1.1.1.5
Count of the number of Loss of Power failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLCurr15MLpr 1.1.890.1.5.13.5.13.21.4.1.1.1.6
Count of the number of Loss of Power failures.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLCurr15MInits 1.1.890.1.5.13.5.13.21.4.1.1.1.7
Count of the line initialization attempts since link up. Includes both successful and failed attempts.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLCurr1DayMonitoredTime 1.1.890.1.5.13.5.13.21.4.1.1.1.8
Units: seconds
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

xdsl2PMLCurr1DayLofs 1.1.890.1.5.13.5.13.21.4.1.1.1.9
Count of the number of Loss of Framing failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLCurr1DayLols 1.1.890.1.5.13.5.13.21.4.1.1.1.10
Count of the number of Loss of Link failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLCurr1DayLol 1.1.890.1.5.13.5.13.21.4.1.1.1.11
Count of the number of Loss of Link failures.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLCurr1DayLprs 1.1.890.1.5.13.5.13.21.4.1.1.1.12
Count of the number of Loss of Power failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLCurr1DayLpr 1.1.890.1.5.13.5.13.21.4.1.1.1.13
Count of the number of Loss of Power failures.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLCurr1DayInits 1.1.890.1.5.13.5.13.21.4.1.1.1.14
Count of the line initialization attempts since link up. Includes both successful and failed attempts.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLSinceLinkInmEqInp 1.1.890.1.5.13.5.13.21.4.1.1.1.15
The INM Equivalent Inp histogram since last link up. An array of 68 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17 bins of the histogram. The particular index of the bin incremented by an impulse noise event is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

xdsl2PMLSinceLinkInmIAT 1.1.890.1.5.13.5.13.21.4.1.1.1.16
The INM Inter Arrival Time histogram since last link up. An array of 32 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram. The index of the particular bin incremented by an complete impulse noise event is determained from the following INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

xdsl2PMLSinceLinkInmME 1.1.890.1.5.13.5.13.21.4.1.1.1.17
The INM total measurement since last link up. This indication occurs every time a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLCurr15MInmEqInp 1.1.890.1.5.13.5.13.21.4.1.1.1.18
The INM Equivalent Inp histogram during this 15min interval. An array of 68 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17 bins of the histogram. The particular index of the bin incremented by an impulse noise event is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

xdsl2PMLCurr15MInmIAT 1.1.890.1.5.13.5.13.21.4.1.1.1.19
The INM Inter Arrival Time histogram during this 15min interval. An array of 32 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram. The index of the particular bin incremented by an complete impulse noise event is determained from the following INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

xdsl2PMLCurr15MInmME 1.1.890.1.5.13.5.13.21.4.1.1.1.20
The INM total measurement during this 15min interval. This indication occurs every time a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLCurr1DayInmEqInp 1.1.890.1.5.13.5.13.21.4.1.1.1.21
The INM Equivalent Inp histogram during this 1Day interval. An array of 68 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17 bins of the histogram. The particular index of the bin incremented by an impulse noise event is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

xdsl2PMLCurr1DayInmIAT 1.1.890.1.5.13.5.13.21.4.1.1.1.22
The INM Inter Arrival Time histogram during this 1Day interval. An array of 32 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram. The index of the particular bin incremented by an complete impulse noise event is determained from the following INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

xdsl2PMLCurr1DayInmME 1.1.890.1.5.13.5.13.21.4.1.1.1.23
The INM total measurement during this 1Day interval. This indication occurs every time a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLSinceInitLofs 1.1.890.1.5.13.5.13.21.4.1.1.1.24
Count of seconds of Loss of Framing failures since initialized.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLSinceInitLols 1.1.890.1.5.13.5.13.21.4.1.1.1.25
Count of seconds of Loss of Link failures since initialized.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLSinceInitLol 1.1.890.1.5.13.5.13.21.4.1.1.1.26
Count of the number of Loss of Link failures since initialized.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLSinceInitLprs 1.1.890.1.5.13.5.13.21.4.1.1.1.27
Count of seconds of Loss of Power failures since initialized.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLSinceInitLpr 1.1.890.1.5.13.5.13.21.4.1.1.1.28
Count of the number of Loss of Power failures since initialized.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLSinceInitInits 1.1.890.1.5.13.5.13.21.4.1.1.1.29
Count of the line initialization attempts since initialized. Includes both successful and failed attempts.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLineHist15MinExtendedTable 1.1.890.1.5.13.5.13.21.4.1.2
The table displays VDSL2 Line History 15 minute Performance Data. This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xdsl2PMLineHist15MinExtendedEntry

xdsl2PMLineHist15MinExtendedEntry 1.1.890.1.5.13.5.13.21.4.1.2.1
An entry of xdsl2PMLineHist15MinExtendedEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Xdsl2PMLineHist15MinExtendedEntry  

xdsl2PMLHist15MLofs 1.1.890.1.5.13.5.13.21.4.1.2.1.1
Count of the number of Loss of Framing failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLHist15MLols 1.1.890.1.5.13.5.13.21.4.1.2.1.2
Count of the number of Loss of Link failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLHist15MLol 1.1.890.1.5.13.5.13.21.4.1.2.1.3
Count of the number of Loss of Link failures.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLHist15MLprs 1.1.890.1.5.13.5.13.21.4.1.2.1.4
Count of the number of Loss of Power failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLHist15MLpr 1.1.890.1.5.13.5.13.21.4.1.2.1.5
Count of the number of Loss of Power failures.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLHist15MInits 1.1.890.1.5.13.5.13.21.4.1.2.1.6
Count of the line initialization attempts since link up. Includes both successful and failed attempts.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLHist15MInmEqInp 1.1.890.1.5.13.5.13.21.4.1.2.1.7
The INM Equivalent Inp histogram during 15min interval. An array of 68 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17 bins of the histogram. The particular index of the bin incremented by an impulse noise event is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

xdsl2PMLHist15MInmIAT 1.1.890.1.5.13.5.13.21.4.1.2.1.8
The INM Inter Arrival Time histogram during 15min interval. An array of 32 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram. The index of the particular bin incremented by an complete impulse noise event is determained from the following INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

xdsl2PMLHist15MInmME 1.1.890.1.5.13.5.13.21.4.1.2.1.9
The INM total measurement during 15min interval. This indication occurs every time a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLineHist1DayExtendedTable 1.1.890.1.5.13.5.13.21.4.1.3
The table displays VDSL2 Line History 1 day Performance Data. This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xdsl2PMLineHist1DayExtendedEntry

xdsl2PMLineHist1DayExtendedEntry 1.1.890.1.5.13.5.13.21.4.1.3.1
An entry of xdsl2PMLineHist1DayExtendedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Xdsl2PMLineHist1DayExtendedEntry  

xdsl2PMLHist1DLofs 1.1.890.1.5.13.5.13.21.4.1.3.1.1
Count of the number of Loss of Framing failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLHist1DLols 1.1.890.1.5.13.5.13.21.4.1.3.1.2
Count of the number of Loss of Link failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLHist1DLol 1.1.890.1.5.13.5.13.21.4.1.3.1.3
Count of the number of Loss of Link failures.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLHist1DLprs 1.1.890.1.5.13.5.13.21.4.1.3.1.4
Count of the number of Loss of Power failures since link up.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLHist1DLpr 1.1.890.1.5.13.5.13.21.4.1.3.1.5
Count of the number of Loss of Power failures.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLHist1DInits 1.1.890.1.5.13.5.13.21.4.1.3.1.6
Count of the line initialization attempts since link up. Includes both successful and failed attempts.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMLHist1DInmEqInp 1.1.890.1.5.13.5.13.21.4.1.3.1.7
The INM Equivalent Inp histogram during 1Day interval. An array of 68 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 1 to 17 bins of the histogram. The particular index of the bin incremented by an impulse noise event is equal to the computed value of equivalent INP, except the 17th of anomaly INPEQ, which logs all equivalent INPs greater than 16. Each bin has a value in the range 0x0 to 0xFFFFFFFF
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

xdsl2PMLHist1DInmIAT 1.1.890.1.5.13.5.13.21.4.1.3.1.8
The INM Inter Arrival Time histogram during 1Day interval. An array of 32 octets (each 4 octets means amount of a bin of histogram), designed for supporting from 0 to 7 bins of the histogram. The index of the particular bin incremented by an complete impulse noise event is determained from the following INMControl parameters. Each bin has a value in the range 0x0 to 0xFFFFFFFF
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

xdsl2PMLHist1DInmME 1.1.890.1.5.13.5.13.21.4.1.3.1.9
The INM total measurement during this 1Day interval. This indication occurs every time a data symbol is processed by the Impulse Noise Sensor. The range of the value is from 0x0 to 0xFFFFFFFF
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMChCurrExtendedTable 1.1.890.1.5.13.5.13.21.4.2.1
The table displays VDSL2 Channel Current Performance Data. This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xdsl2PMChCurrExtendedEntry

xdsl2PMChCurrExtendedEntry 1.1.890.1.5.13.5.13.21.4.2.1.1
An entry of xdsl2PMChHist15MinExtendedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Xdsl2PMChCurrExtendedEntry  

xdsl2PMChCurr15MUncorrectBlks 1.1.890.1.5.13.5.13.21.4.2.1.1.1
Count of all blocks received with uncorrectable errors on this channel within the current 15 minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMChCurr1DayUncorrectBlks 1.1.890.1.5.13.5.13.21.4.2.1.1.2
Count of all blocks received with uncorrectable errors on this channel within the current 7 day interval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMChSinceLinkRtx 1.1.890.1.5.13.5.13.21.4.2.1.1.3
Number of codewords retransmitted since last link up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChCurr15MRtx 1.1.890.1.5.13.5.13.21.4.2.1.1.4
Number of codewords retransmitted during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChCurr1DayRtx 1.1.890.1.5.13.5.13.21.4.2.1.1.5
Number of codewords retransmitted during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChSinceLinkRtxCorrected 1.1.890.1.5.13.5.13.21.4.2.1.1.6
Number of codewords corrected through retransmission since last link up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChCurr15MRtxCorrected 1.1.890.1.5.13.5.13.21.4.2.1.1.7
Number of codewords corrected through retransmission during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChCurr1DayRtxCorrected 1.1.890.1.5.13.5.13.21.4.2.1.1.8
Number of codewords corrected through retransmission during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChSinceLinkRtxUncorrected 1.1.890.1.5.13.5.13.21.4.2.1.1.9
Number of codewords left uncorrected after retransmission since last link up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChCurr15MRtxUncorrected 1.1.890.1.5.13.5.13.21.4.2.1.1.10
Number of codewords left uncorrected after retransmission during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChCurr1DayRtxUncorrected 1.1.890.1.5.13.5.13.21.4.2.1.1.11
Number of codewords left uncorrected after retransmission during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChSinceLinkLEFTRs 1.1.890.1.5.13.5.13.21.4.2.1.1.12
Low Error-Free Throughput Rate Seconds since last link up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChCurr15MLEFTRs 1.1.890.1.5.13.5.13.21.4.2.1.1.13
Low Error-Free Throughput Rate Seconds during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChCurr1DayLEFTRs 1.1.890.1.5.13.5.13.21.4.2.1.1.14
Low Error-Free Throughput Rate Seconds during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChSinceLinkMinEFTR 1.1.890.1.5.13.5.13.21.4.2.1.1.15
Lowest EFTR observed since last link up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChCurr15MMinEFTR 1.1.890.1.5.13.5.13.21.4.2.1.1.16
Lowest EFTR observed in the current interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChCurr1DayMinEFTR 1.1.890.1.5.13.5.13.21.4.2.1.1.17
Lowest EFTR observed in the current interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChSinceLinkErrFreeBits 1.1.890.1.5.13.5.13.21.4.2.1.1.18
The number of bits belonging to correct DTUs leaving the Rx PMS-TC oo 2(oV16) since last link up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChCurr15MErrFreeBits 1.1.890.1.5.13.5.13.21.4.2.1.1.19
The number of bits belonging to correct DTUs leaving the Rx PMS-TC oo 2(oV16) during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChCurr1DayErrFreeBits 1.1.890.1.5.13.5.13.21.4.2.1.1.20
The number of bits belonging to correct DTUs leaving the Rx PMS-TC oo 2(oV16) during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChHist15MinExtendedTable 1.1.890.1.5.13.5.13.21.4.3.1
The table displays VDSL2 Channel History 15 minute Performance Data. This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xdsl2PMChHist15MinExtendedEntry

xdsl2PMChHist15MinExtendedEntry 1.1.890.1.5.13.5.13.21.4.3.1.1
An entry of xdsl2PMChHist15MinExtendedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Xdsl2PMChHist15MinExtendedEntry  

xdsl2PMChHist15MUncorrectBlks 1.1.890.1.5.13.5.13.21.4.3.1.1.1
Count of all blocks received with uncorrectable errors on this channel within the history 15 minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMChHist15MRtx 1.1.890.1.5.13.5.13.21.4.3.1.1.2
Number of codewords retransmitted during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChHist15MRtxCorrected 1.1.890.1.5.13.5.13.21.4.3.1.1.3
Number of codewords corrected through retransmission during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChHist15MRtxUncorrected 1.1.890.1.5.13.5.13.21.4.3.1.1.4
Number of codewords left uncorrected after retransmission during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChHist15MLEFTRs 1.1.890.1.5.13.5.13.21.4.3.1.1.5
Low Error-Free Throughput Rate Seconds during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChHist15MMinEFTR 1.1.890.1.5.13.5.13.21.4.3.1.1.6
Lowest EFTR observed in the current interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChHist15MErrFreeBits 1.1.890.1.5.13.5.13.21.4.3.1.1.7
The number of bits belonging to correct DTUs leaving the Rx PMS-TC oo 2(oV16) during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChHist1DExtendedTable 1.1.890.1.5.13.5.13.21.4.3.2
The table displays VDSL2 Channel History 1 day Performance Data. This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xdsl2PMChHist1DExtendedEntry

xdsl2PMChHist1DExtendedEntry 1.1.890.1.5.13.5.13.21.4.3.2.1
An entry of xdsl2PMChHist1DExtendedTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Xdsl2PMChHist1DExtendedEntry  

xdsl2PMChHist1DUncorrectBlks 1.1.890.1.5.13.5.13.21.4.3.2.1.1
Count of all blocks received with uncorrectable errors on this channel within the history 1 day interval.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

xdsl2PMChHist1DayRtx 1.1.890.1.5.13.5.13.21.4.3.2.1.2
Number of codewords retransmitted during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChHist1DayRtxCorrected 1.1.890.1.5.13.5.13.21.4.3.2.1.3
Number of codewords corrected through retransmission during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChHist1DayRtxUncorrected 1.1.890.1.5.13.5.13.21.4.3.2.1.4
Number of codewords left uncorrected after retransmission during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChHist1DayLEFTRs 1.1.890.1.5.13.5.13.21.4.3.2.1.5
Low Error-Free Throughput Rate Seconds during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChHist1DayMinEFTR 1.1.890.1.5.13.5.13.21.4.3.2.1.6
Lowest EFTR observed in the current interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2PMChHist1DayErrFreeBits 1.1.890.1.5.13.5.13.21.4.3.2.1.7
The number of bits belonging to correct DTUs leaving the Rx PMS-TC oo 2(oV16) during this interval.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

xdsl2LineBandExtTable 1.1.890.1.5.13.5.13.21.5
This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    Xdsl2LineBandExtEntry

xdsl2LineBandExtEntry 1.1.890.1.5.13.5.13.21.5.1
An entry of xdsl2LineBandExtTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  Xdsl2LineBandExtEntry  

xdsl2LineBandTxPower 1.1.890.1.5.13.5.13.21.5.1.1
Xdsl line band Tx power (in unit of 0.1 Dbm, -1280 indicates that power is empty)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

xdsl2LineBandRxPower 1.1.890.1.5.13.5.13.21.5.1.2
Xdsl line band Rx power (in unit of 0.1 Dbm, -1280 indicates that power is empty)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mldStatsV1QueryInCnt 1.1.890.1.5.13.5.13.22.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldStatsV1ReportInCnt 1.1.890.1.5.13.5.13.22.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldStatsV1DoneInCnt 1.1.890.1.5.13.5.13.22.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldStatsV1QueryInDropCnt 1.1.890.1.5.13.5.13.22.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldStatsV1ReportInDropCnt 1.1.890.1.5.13.5.13.22.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldStatsV1DoneInDropCnt 1.1.890.1.5.13.5.13.22.6
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldStatsV1QueryOutCnt 1.1.890.1.5.13.5.13.22.7
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldStatsV1ReportOutCnt 1.1.890.1.5.13.5.13.22.8
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldStatsV1DoneOutCnt 1.1.890.1.5.13.5.13.22.9
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldStatsV2QueryInCnt 1.1.890.1.5.13.5.13.22.10
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldStatsV2ReportInCnt 1.1.890.1.5.13.5.13.22.11
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldStatsV2QueryInDropCnt 1.1.890.1.5.13.5.13.22.12
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldStatsV2ReportInDropCnt 1.1.890.1.5.13.5.13.22.13
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldStatsV2QueryOutCnt 1.1.890.1.5.13.5.13.22.14
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldStatsV2ReportOutCnt 1.1.890.1.5.13.5.13.22.15
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldNumOfActiveGroups 1.1.890.1.5.13.5.13.22.16
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mldGroupTable 1.1.890.1.5.13.5.13.22.17
This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MldGroupEntry

mldGroupEntry 1.1.890.1.5.13.5.13.22.17.1
An entry of mldGroupTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MldGroupEntry  

mldGroupVid 1.1.890.1.5.13.5.13.22.17.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

mldGroupIp 1.1.890.1.5.13.5.13.22.17.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

mldGroupNumOfMembers 1.1.890.1.5.13.5.13.22.17.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mldGroupMemberPorts 1.1.890.1.5.13.5.13.22.17.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  PortList  

mldGroupNumOfActiveUsers 1.1.890.1.5.13.5.13.22.17.1.5
Number of active users.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mldGroupPortTable 1.1.890.1.5.13.5.13.22.18
This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MldGroupPortEntry

mldGroupPortEntry 1.1.890.1.5.13.5.13.22.18.1
An entry of mldGroupPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MldGroupPortEntry  

mldGroupPortVid 1.1.890.1.5.13.5.13.22.18.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

mldGroupPortIp 1.1.890.1.5.13.5.13.22.18.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

mldGroupPortSourceIp 1.1.890.1.5.13.5.13.22.18.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

mldPortCtrlPduTable 1.1.890.1.5.13.5.13.22.19
This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MldPortCtrlPduEntry

mldPortCtrlPduEntry 1.1.890.1.5.13.5.13.22.19.1
An entry of mldPortCtrlPduTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MldPortCtrlPduEntry  

mldPortCtrlPduQueryCnt 1.1.890.1.5.13.5.13.22.19.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldPortCtrlPduReportCnt 1.1.890.1.5.13.5.13.22.19.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldPortCtrlPduLeaveCnt 1.1.890.1.5.13.5.13.22.19.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldPortNumOfActiveGroups 1.1.890.1.5.13.5.13.22.19.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mldPortCtrlPduV1SuccessJoinCnt 1.1.890.1.5.13.5.13.22.19.1.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldPortCtrlPduV1UnsuccJoinCnt 1.1.890.1.5.13.5.13.22.19.1.6
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldPortCtrlPduGenQryCnt 1.1.890.1.5.13.5.13.22.19.1.7
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldPortCtrlPduSpecQryCnt 1.1.890.1.5.13.5.13.22.19.1.8
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldPortCtrlPduV2SuccessReportCnt 1.1.890.1.5.13.5.13.22.19.1.9
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldPortCtrlPduV2UnsuccReportCnt 1.1.890.1.5.13.5.13.22.19.1.10
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldPortCtrlPduInvalidCnt 1.1.890.1.5.13.5.13.22.19.1.11
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldVlanStatsTable 1.1.890.1.5.13.5.13.22.20
This table is supported by R5.06 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MldVlanStatsuEntry

mldVlanStatsuEntry 1.1.890.1.5.13.5.13.22.20.1
An entry of mldVlanStatsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MldVlanStatsuEntry  

mldVlanStatsVlanIndex 1.1.890.1.5.13.5.13.22.20.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

mldVlanStatsNumOfActiveGroups 1.1.890.1.5.13.5.13.22.20.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mldVlanStatsQueryPort 1.1.890.1.5.13.5.13.22.20.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mldVlanStatsQuerierIp 1.1.890.1.5.13.5.13.22.20.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

mldVlanStatsV1QueryInCnt 1.1.890.1.5.13.5.13.22.20.1.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldVlanStatsV1ReportInCnt 1.1.890.1.5.13.5.13.22.20.1.6
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldVlanStatsV1DoneInCnt 1.1.890.1.5.13.5.13.22.20.1.7
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldVlanStatsV1QueryInDropCnt 1.1.890.1.5.13.5.13.22.20.1.8
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldVlanStatsV1ReportInDropCnt 1.1.890.1.5.13.5.13.22.20.1.9
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldVlanStatsV1DoneInDropCnt 1.1.890.1.5.13.5.13.22.20.1.10
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldVlanStatsV1QueryOutCnt 1.1.890.1.5.13.5.13.22.20.1.11
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldVlanStatsV1ReportOutCnt 1.1.890.1.5.13.5.13.22.20.1.12
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldVlanStatsV1DoneOutCnt 1.1.890.1.5.13.5.13.22.20.1.13
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldVlanStatsV2QueryInCnt 1.1.890.1.5.13.5.13.22.20.1.14
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldVlanStatsV2ReportInCnt 1.1.890.1.5.13.5.13.22.20.1.15
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldVlanStatsV2QueryInDropCnt 1.1.890.1.5.13.5.13.22.20.1.16
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldVlanStatsV2ReportInDropCnt 1.1.890.1.5.13.5.13.22.20.1.17
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldVlanStatsV2QueryOutCnt 1.1.890.1.5.13.5.13.22.20.1.18
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

mldVlanStatsV2ReportOutCnt 1.1.890.1.5.13.5.13.22.20.1.19
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

macFFArpStatusUplinkTable 1.1.890.1.5.13.5.13.23.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFFArpStatusUplinkEntry

macFFArpStatusUplinkEntry 1.1.890.1.5.13.5.13.23.1.1
The entry of macFFArpStatusUplinkTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFFArpStatusUplinkEntry  

macFFArpStatusUplinkIpAddr 1.1.890.1.5.13.5.13.23.1.1.1
macFF arp ip address from uplink
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

macFFArpStatusUplinkMacAddr 1.1.890.1.5.13.5.13.23.1.1.2
macFF arp mac address from uplink
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

macFFArpStatusUplinkMacVid 1.1.890.1.5.13.5.13.23.1.1.3
macFF arp vid from uplink
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4094  

macFFArpStatusSlotTable 1.1.890.1.5.13.5.13.23.2
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFFArpStatusSlotEntry

macFFArpStatusSlotEntry 1.1.890.1.5.13.5.13.23.2.1
The entry of macFFArpStatusSlotTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFFArpStatusSlotEntry  

macFFArpStatusSlotIpAddr 1.1.890.1.5.13.5.13.23.2.1.1
macFF arp ip address from subscrib port
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

macFFArpStatusSlotMacAddr 1.1.890.1.5.13.5.13.23.2.1.2
macFF arp mac address from subscrib port
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

macFFArpStatusSlotMacVid 1.1.890.1.5.13.5.13.23.2.1.3
macFF arp vid from subscrib port
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..4094  

macFFArpStatusSlotPort 1.1.890.1.5.13.5.13.23.2.1.4
macFF arp learnt subscrib port
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

macFFArpCntUplinkTable 1.1.890.1.5.13.5.13.23.3
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFFArpCntUplinkEntry

macFFArpCntUplinkEntry 1.1.890.1.5.13.5.13.23.3.1
The entry of macFFArpCntUplinkTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFFArpCntUplinkEntry  

macFFArpCntUplinkReqRx 1.1.890.1.5.13.5.13.23.3.1.1
macFF arp request rx counter from uplink
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

macFFArpCntUplinkReqTx 1.1.890.1.5.13.5.13.23.3.1.2
macFF arp request tx counter from uplink
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

macFFArpCntUplinkReqRxDrop 1.1.890.1.5.13.5.13.23.3.1.3
macFF arp request rx drop counter from uplink
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

macFFArpCntUplinkRpyRx 1.1.890.1.5.13.5.13.23.3.1.4
macFF arp reply rx counter from uplink
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

macFFArpCntUplinkRpyTx 1.1.890.1.5.13.5.13.23.3.1.5
macFF arp reply tx counter from uplink
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

macFFArpCntUplinkRpyRxDrop 1.1.890.1.5.13.5.13.23.3.1.6
macFF arp reply rx drop counter from uplink
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

macFFArpCntPortTable 1.1.890.1.5.13.5.13.23.4
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MacFFArpCntPortEntry

macFFArpCntPortEntry 1.1.890.1.5.13.5.13.23.4.1
The entry of macFFArpCntPortTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacFFArpCntPortEntry  

macFFArpCntPortReqRx 1.1.890.1.5.13.5.13.23.4.1.1
macFF arp request rx counter from subscrib port
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

macFFArpCntPortReqTx 1.1.890.1.5.13.5.13.23.4.1.2
macFF arp request tx counter from subscrib port
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

macFFArpCntPortReqRxDrop 1.1.890.1.5.13.5.13.23.4.1.3
macFF arp request rx drop counter from subscrib port
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

macFFArpCntPortRpyRx 1.1.890.1.5.13.5.13.23.4.1.4
macFF arp reply rx counter from subscrib port
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

macFFArpCntPortRpyTx 1.1.890.1.5.13.5.13.23.4.1.5
macFF arp reply tx counter from subscrib port
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

macFFArpCntPortRpyRxDrop 1.1.890.1.5.13.5.13.23.4.1.6
macFF reply rx drop counter from subscrib port
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

sysBootUpFwIndex 1.1.890.1.5.13.5.13.24.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sysBootUpFwVersion 1.1.890.1.5.13.5.13.24.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

sysFlashFwInfoTable 1.1.890.1.5.13.5.13.24.3
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SysFlashFwInfoEntry

sysFlashFwInfoEntry 1.1.890.1.5.13.5.13.24.3.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SysFlashFwInfoEntry  

sysFlashFwIndex 1.1.890.1.5.13.5.13.24.3.1.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..2  

sysFlashFwVersion 1.1.890.1.5.13.5.13.24.3.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

imaClear 1.1.890.1.5.13.5.14.5
OBJECT IDENTIFIER    

voipClear 1.1.890.1.5.13.5.14.6
OBJECT IDENTIFIER    

counterClearTarget 1.1.890.1.5.13.5.14.1
This object is supported by R1.02 and later versions. This managed object is used for identify the target on which the counter would be cleared. The target is encoded as: Byte 1: the octet specifies a set of eight chassis, chassis 0 through 7 Byte 2~4: each octet specifies a set of eight slots, with the first octet specifying slots 1 through 8, and the second octet specifying slots 9 through 16, and so on. Byte 5~: each octet specifies a set of eight ports, with the first octet specifying ports 1 through 8, etc.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

counterClearOps 1.1.890.1.5.13.5.14.2
This object is supported by R1.02 and later versions. The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 1: clear interface counters BIT 2: clear pvc packet counters BIT 3: clear port ATM counters BIT 4: clear pvc ATM counters BIT 5: clear DHCP counters BIT 6: clear IGMP counters BIT 7: clear IGMP port counters BIT 8: clear inband IP interface counters BIT 9: clear outband IP interface counters BIT10: clear line performance counters BIT11: clear performance current counters BIT12: clear performance current 15min counters BIT13: clear performance current 1day counters BIT14: clear macFF arp counters
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

counterClearVpi 1.1.890.1.5.13.5.14.3
This object is supported by R1.02 and later versions. VPI of the pvc whose counters would be cleared.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

counterClearVci 1.1.890.1.5.13.5.14.4
This object is supported by R1.02 and later versions. VCI of the pvc whose counters would be cleared.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

imaClearOps 1.1.890.1.5.13.5.14.5.1
This object is supported by R5.03 and later versions. The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 0: clear pvc pkt counters BIT 1: clear group cell counters BIT 2: clear ima group performance current 15min counters BIT 3: clear ima group performance current 1day counters BIT 4: clear ima link performance current 15min counters BIT 5: clear ima link performance current 1day counters BIT 6: clear e1 performance current 15min counters BIT 7: clear e1 performance current 1day counters
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

imaClearTargetGroupIndex 1.1.890.1.5.13.5.14.5.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

imaClearTargetLinkIndex 1.1.890.1.5.13.5.14.5.3
1~8, link index in the group
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

imaClearTargetVpi 1.1.890.1.5.13.5.14.5.4
This object is supported by R5.03 and later versions. VPI of the pvc whose counters would be cleared.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

imaClearTargetVci 1.1.890.1.5.13.5.14.5.5
This object is supported by R5.03 and later versions. VCI of the pvc whose counters would be cleared.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

imaClearTargetIfindex 1.1.890.1.5.13.5.14.5.6
This object is supported by R5.03 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipClearOps 1.1.890.1.5.13.5.14.6.1
The corresponding bit is set to 1 to start the operation. The various bit positions are: BIT 0: clear call detail records BIT 1: clear H248 statistics
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipClearH248TargetInterface 1.1.890.1.5.13.5.14.6.2
Interface Id
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

clusterEnable 1.1.890.1.5.13.5.15.1
Enable/disable clustering. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enableManager(1), enableMember(2), disable(3)  

clusterName 1.1.890.1.5.13.5.15.2
Name of the cluster. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

clusterMemberPassword 1.1.890.1.5.13.5.15.3
Password of the member. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

clusterVlan 1.1.890.1.5.13.5.15.4
Setting cluster VLAN ID. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

clusterCandidate 1.1.890.1.5.13.5.15.5
OBJECT IDENTIFIER    

clusterCandidateFlush 1.1.890.1.5.13.5.15.5.1
Setting the object to be 1 to flush the candidate table and re-discover candidates. This object is supported by R3.00 and later versions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

clusterCandidateTable 1.1.890.1.5.13.5.15.5.2
A table that contains information about cluster candidates. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClusterCandidateEntry

clusterCandidateEntry 1.1.890.1.5.13.5.15.5.2.1
An entry of clusterCandidateTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClusterCandidateEntry  

clusterCandidateMacAddr 1.1.890.1.5.13.5.15.5.2.1.1
The MAC address of the candidate.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

clusterCandidateHostName 1.1.890.1.5.13.5.15.5.2.1.2
The host name of the candidate.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

clusterCandidateModelName 1.1.890.1.5.13.5.15.5.2.1.3
The model name of the candidate.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

clusterCandidateDeviceType 1.1.890.1.5.13.5.15.5.2.1.4
The device type of the candidate.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), ies5000(2), ies5005(3), ies6000(4), ies1248-71(101), ies1248-73(102), ies1248-51(103), ies1248-53(104)  

clusterMemberConfTable 1.1.890.1.5.13.5.15.6
A table that contains configuration about cluster members. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClusterMemberConfEntry

clusterMemberConfEntry 1.1.890.1.5.13.5.15.6.1
An entry of clusterMemberConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClusterMemberConfEntry  

clusterMemberConfId 1.1.890.1.5.13.5.15.6.1.1
The identity of the entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

clusterMemberConfMacAddr 1.1.890.1.5.13.5.15.6.1.2
The MAC address of the member which will join the cluster.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

clusterMemberConfPasswd 1.1.890.1.5.13.5.15.6.1.3
The password of the member which will join the cluster.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

clusterMemberStatusTable 1.1.890.1.5.13.5.15.7
A table that contains information about cluster members. This table is supported by R3.00 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ClusterMemberStatusEntry

clusterMemberStatusEntry 1.1.890.1.5.13.5.15.7.1
An entry of clusterMemberStatusTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ClusterMemberStatusEntry  

clusterMemberStatusState 1.1.890.1.5.13.5.15.7.1.1
The state of the member.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER waiting(1), inactive(2), active(3), empty(4), error(5)  

clusterMemberStatusMacAddr 1.1.890.1.5.13.5.15.7.1.2
The MAC address of the member.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

clusterMemberStatusHostName 1.1.890.1.5.13.5.15.7.1.3
The host name of the member.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

clusterMemberStatusModelName 1.1.890.1.5.13.5.15.7.1.4
The model name of the member.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

clusterMemberStatusDeviceType 1.1.890.1.5.13.5.15.7.1.5
The device type of the member.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), ies5000(2), ies5005(3), ies6000(4), ies1248-71(101), ies1248-73(102), ies1248-51(103), ies1248-53(104)  

clusterMemberStatusFWVersion 1.1.890.1.5.13.5.15.7.1.6
The F/W version of the member.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

clusterMemberStatusUpTime 1.1.890.1.5.13.5.15.7.1.7
The time since the member joined the cluster.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

voipArp 1.1.890.1.5.13.5.16.1
OBJECT IDENTIFIER    

voipSip 1.1.890.1.5.13.5.16.2
OBJECT IDENTIFIER    

voipH248 1.1.890.1.5.13.5.16.10
OBJECT IDENTIFIER    

voipArpFlushTarget 1.1.890.1.5.13.5.16.1.1
Flush arp entries in the specified slot.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipArpFlushOps 1.1.890.1.5.13.5.16.1.2
Set the object to 1 to start flushing.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipArpShowTable 1.1.890.1.5.13.5.16.1.3
Display ARP entries learnt in specified slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipArpShowEntry

voipArpShowEntry 1.1.890.1.5.13.5.16.1.3.1
An entry of voipArpShowTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipArpShowEntry  

voipArpShowIp 1.1.890.1.5.13.5.16.1.3.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipArpShowMac 1.1.890.1.5.13.5.16.1.3.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

voipArpShowTimer 1.1.890.1.5.13.5.16.1.3.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

maxNumOfVoipNumberPlan 1.1.890.1.5.13.5.16.2.1
The maximum number of VoIP number plan supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipNumberPlanTable 1.1.890.1.5.13.5.16.2.2
Configure numbering plan entry of specified index in specified payphone charging table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipNumberPlanEntry

voipNumberPlanEntry 1.1.890.1.5.13.5.16.2.2.1
An entry of voipNumberPlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipNumberPlanEntry  

voipNumberPlanName 1.1.890.1.5.13.5.16.2.2.1.1
Numbering plan table name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipNumberPlanIndex 1.1.890.1.5.13.5.16.2.2.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

voipNumberPlanPattern 1.1.890.1.5.13.5.16.2.2.1.3
up to 47 characters, allow digit, '*', and '#' characters and meaning characters that include 'x', '.', '|' and range format characters that include '~', ',' and parenthesis '(', ')' and brackets '[', ']' and at most one parenthesis pair and 'T' for terminate are allowed and two quotation marks means a null pattern for hot dial, examples: '002(x.)', '0(x.)', and '(x.)'
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..47)  

voipNumberPlanRule 1.1.890.1.5.13.5.16.2.2.1.4
Allowed characters are 0~9, and '\c' stand for country code, '\d' stand for national destination code, '' stand for matched string enclosed by the parenthesis pair, and 'deny' stand for the pattern specified is not allowed and accept 1-15 digits includes '+', '*' and '#' for hot or speed dial application. Examples: '', '\c', and '\c\d'.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..15)  

voipNumberPlanRowStatus 1.1.890.1.5.13.5.16.2.2.1.5
This object is used to create a new entry or delete an existing entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

maxNumOfVoipDialPlan 1.1.890.1.5.13.5.16.2.3
The maximum number of VoIP dial plan supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipDialPlanTable 1.1.890.1.5.13.5.16.2.4
Configure dial plan related configuration. This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipDialPlanEntry

voipDialPlanEntry 1.1.890.1.5.13.5.16.2.4.1
An entry of voipDialPlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipDialPlanEntry  

voipDialPlanName 1.1.890.1.5.13.5.16.2.4.1.1
Dial plan table name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipDialPlanPattern 1.1.890.1.5.13.5.16.2.4.1.2
only 63 DTMF characters that include digits, '*', '#' and meaning characters that include 'x', '.', '|' and characters of range format that include '~', ',' and brackets ('[', ']') are allowed. Note: 'x' represents any digit character '.' represents one or more repetitions of character or range that precedes it, can't use in brackets '!' represents the user-dialed number can be rejected by placing '!' at the end of the pattern '|' to connect next sub-pattern '[' and ']' must pair and nest brackets is illegal '~' and ',' only show in brackets '~' connected characters must be digit User should make sure to create unique pattern for each SIP proxy server. The VOP1248G-61 is not able to distinguish between dial plan tables if they have the same pattern.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..63)  

voipDialPlanNumOfPrefixCut 1.1.890.1.5.13.5.16.2.4.1.3
The number of digits at the beginning of the dialed number that will be removed.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..8  

voipDialPlanSipServer 1.1.890.1.5.13.5.16.2.4.1.4
SIP profile name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..31)  

voipDialPlanPrefixAddDigits 1.1.890.1.5.13.5.16.2.4.1.5
Only digit characters are allowed or use two quotation mark to indicate no prefix added digits.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..15)  

voipDialPlanNumberOfInterdigit 1.1.890.1.5.13.5.16.2.4.1.6
The number of dialing digits.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..15  

voipDialPlanInterdigitTimeout 1.1.890.1.5.13.5.16.2.4.1.7
Inter-digit timeout in seconds.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..10  

voipDialPlanRowStatus 1.1.890.1.5.13.5.16.2.4.1.8
This object is used to create a new entry or delete an existing entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

maxNumOfVoipKeyPattern 1.1.890.1.5.13.5.16.2.5
The maximum number of VoIP key patterns supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipKeyPatternTable 1.1.890.1.5.13.5.16.2.6
Configure key pattern related configuration. This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipKeyPatternEntry

voipKeyPatternEntry 1.1.890.1.5.13.5.16.2.6.1
An entry of voipKeyPatternTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipKeyPatternEntry  

voipKeyPatternName 1.1.890.1.5.13.5.16.2.6.1.1
Key pattern table name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipKeyPatternServiceType 1.1.890.1.5.13.5.16.2.6.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER callreturn(1), calltransfer(2), callwaitdisconn(3), callwaitoff(4), callwaiton(5), callwaitonhold(6), callwaitreject(7), clir(8), dndoff(9), dndon(10), callin(11)  

voipKeyPatternPattern 1.1.890.1.5.13.5.16.2.6.1.3
Allowed characters are 0~9, *, and #.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..7)  

voipKeyPatternRowStatus 1.1.890.1.5.13.5.16.2.6.1.4
This object is used to create a new entry or delete an existing entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

voipLocalCall 1.1.890.1.5.13.5.16.2.7
OBJECT IDENTIFIER    

voipLocalCallSync 1.1.890.1.5.13.5.16.2.7.1
Set the object to 1 to synchronize msc local call file with SIP linecard.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipLocalCallEnterTime 1.1.890.1.5.13.5.16.2.7.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..60  

voipLocalCallExitTime 1.1.890.1.5.13.5.16.2.7.3
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..60  

maxNumOfVoipLocalHelp 1.1.890.1.5.13.5.16.2.8
The maximum number of VoIP local help entries supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipLocalHelpTable 1.1.890.1.5.13.5.16.2.9
Configure telephone number of specified index in specified local help table. This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipLocalHelpEntry

voipLocalHelpEntry 1.1.890.1.5.13.5.16.2.9.1
An entry of voipLocalHelpTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipLocalHelpEntry  

voipLocalHelpName 1.1.890.1.5.13.5.16.2.9.1.1
Local help table name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipLocalHelpIndex 1.1.890.1.5.13.5.16.2.9.1.2
Index number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

voipLocalHelpTelNumber 1.1.890.1.5.13.5.16.2.9.1.3
Only digits are allowed.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..15)  

voipLocalHelpRowStatus 1.1.890.1.5.13.5.16.2.9.1.4
This object is used to create a new entry or delete an existing entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

voipIpSetTable 1.1.890.1.5.13.5.16.3
Configure IP address and VLAN ID of specified slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipIpSetEntry

voipIpSetEntry 1.1.890.1.5.13.5.16.3.1
An entry of voipIpSetTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipIpSetEntry  

voipIpSetIp 1.1.890.1.5.13.5.16.3.1.1
IP address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

voipIpSetVid 1.1.890.1.5.13.5.16.3.1.2
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

voipIpSetMask 1.1.890.1.5.13.5.16.3.1.3
Network mask.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..32  

voipDnsTable 1.1.890.1.5.13.5.16.4
Configure DNS server IP of specified slot.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipDnsEntry

voipDnsEntry 1.1.890.1.5.13.5.16.4.1
An entry of voipDnsTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipDnsEntry  

voipDnsIp 1.1.890.1.5.13.5.16.4.1.1
IP address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

maxNumOfVoipRoute 1.1.890.1.5.13.5.16.7
The maximum number of VoIP routing entries in a slot.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipRouteTable 1.1.890.1.5.13.5.16.8
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipRouteEntry

voipRouteEntry 1.1.890.1.5.13.5.16.8.1
An entry of voipRouteTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipRouteEntry  

voipRouteSlot 1.1.890.1.5.13.5.16.8.1.1
Specified slot number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipRouteIp 1.1.890.1.5.13.5.16.8.1.2
IP address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipRouteGateway 1.1.890.1.5.13.5.16.8.1.3
Gateway IP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipRouteMask 1.1.890.1.5.13.5.16.8.1.4
Network mask.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..32  

voipRouteMetric 1.1.890.1.5.13.5.16.8.1.5
Metric number of the route.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..15  

voipRouteRowStatus 1.1.890.1.5.13.5.16.8.1.6
This object is used to create a new entry or delete an existing entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

voipCountryCode 1.1.890.1.5.13.5.16.9
Configure country code (information) for VoIP services.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER usa(1), taiwan(2), austria(3), belgium(4), denmark(5), finland(6), netherland(7), norway(8), spain(9), sweden(10), switzerland(11), uk(12), germany(13), australia(14), ireland(15), czech(16), italy(17), japan(18), new-zealand(19), russia(20), china(21), vietnam(22), brazil(23), bulgaria(24), france(25), hungary(26), iceland(27), luxembourg(28), poland(29), portugal(30), slovakia(31), greece(32), hongkong(33), singapore(34), morocco(35), malaysia(36), thailand(37), israle(38), uae(39), ukraine(40), south-africa(41), south-korea(42), philippines(43), india(44), turkey(45), iran(46)  

voipH248MgConfTable 1.1.890.1.5.13.5.16.10.1
This table is used to create MG instance at specified slot with specified MGC profile. This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipH248MgConfEntry

voipH248MgConfEntry 1.1.890.1.5.13.5.16.10.1.1
An entry in voipH248MgConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipH248MgConfEntry  

voipH248MgConfSlot 1.1.890.1.5.13.5.16.10.1.1.1
Line card slot number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248MgConfName 1.1.890.1.5.13.5.16.10.1.1.2
MG name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipH248MgConfEnable 1.1.890.1.5.13.5.16.10.1.1.3
Enable/disable MG.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

voipH248MgConfH248Profile 1.1.890.1.5.13.5.16.10.1.1.4
H.248 profile name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipH248MgConfPort 1.1.890.1.5.13.5.16.10.1.1.5
MG port number.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1025..65535  

voipH248MgConfRowStatus 1.1.890.1.5.13.5.16.10.1.1.6
This object is used to create a new row or delete an existing row in this table..
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

voipH248InterfaceConfTable 1.1.890.1.5.13.5.16.10.2
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipH248InterfaceConfEntry

voipH248InterfaceConfEntry 1.1.890.1.5.13.5.16.10.2.1
An entry in voipH248InterfaceConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipH248InterfaceConfEntry  

voipH248InterfaceConfId 1.1.890.1.5.13.5.16.10.2.1.1
Line card slot number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248InterfaceConfMgName 1.1.890.1.5.13.5.16.10.2.1.2
MG name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipH248InterfaceConfMgEnable 1.1.890.1.5.13.5.16.10.2.1.3
Enable/disable MG.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

voipH248InterfaceConfH248Profile 1.1.890.1.5.13.5.16.10.2.1.4
H.248 profile name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipH248InterfaceConfPort 1.1.890.1.5.13.5.16.10.2.1.5
MG port number.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1025..65535  

voipH248InterfaceConfIp 1.1.890.1.5.13.5.16.10.2.1.6
Interface Ip
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

voipH248InterfaceConfMasklen 1.1.890.1.5.13.5.16.10.2.1.7
network mask, 0~32
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipH248InterfaceConfVid 1.1.890.1.5.13.5.16.10.2.1.8
1~4094
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

voipH248InterfaceConfPrimary 1.1.890.1.5.13.5.16.10.2.1.9
slot id
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipH248InterfaceConfSecondary 1.1.890.1.5.13.5.16.10.2.1.10
slot id
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipH248InterfaceConfBhcaPeak 1.1.890.1.5.13.5.16.10.2.1.11
peak call attempt allowance in one second , 0~30
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipH248InterfaceConfBhcaAverage 1.1.890.1.5.13.5.16.10.2.1.12
average call attempt allowance in one hour, 0~60000
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipH248SlotConfTable 1.1.890.1.5.13.5.16.10.3
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipH248SlotConfEntry

voipH248SlotConfEntry 1.1.890.1.5.13.5.16.10.3.1
An entry in voipH248ConfSlotTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipH248SlotConfEntry  

voipH248SlotConfId 1.1.890.1.5.13.5.16.10.3.1.1
Line card slot number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248SlotConfMasterIp1 1.1.890.1.5.13.5.16.10.3.1.2
Master Ip
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

voipH248SlotConfMasterIp2 1.1.890.1.5.13.5.16.10.3.1.3
Master Ip
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

voipH248SlotConfOpmode 1.1.890.1.5.13.5.16.10.3.1.4
Opmode
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER mc(1), sc(2)  

voipH248SlotConf8021pPrio 1.1.890.1.5.13.5.16.10.3.1.5
802.1p bit for H.248 internal message packet, 0 ~ 7
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipH248SlotConfPriorityDscp 1.1.890.1.5.13.5.16.10.3.1.6
DSCP for H.248 internal message packet, 0 ~ 63
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipH248SlaveConfTable 1.1.890.1.5.13.5.16.10.4
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipH248SlaveConfEntry

voipH248SlaveConfEntry 1.1.890.1.5.13.5.16.10.4.1
An entry in voipH248InterfaceSlaveTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipH248SlaveConfEntry  

voipH248SlaveConfInterfaceId 1.1.890.1.5.13.5.16.10.4.1.1
Line card slot number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipH248SlaveConfSlaveId 1.1.890.1.5.13.5.16.10.4.1.2
Slave Member
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipH248SlaveConfSlaveIp 1.1.890.1.5.13.5.16.10.4.1.3
Slave Ip
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

voipH248Localcall 1.1.890.1.5.13.5.16.10.5
OBJECT IDENTIFIER    

voipH248LocalcallEnterTime 1.1.890.1.5.13.5.16.10.5.1
The time to enter localcall utility after MGC missing. 1~60, in unit of minutes
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..60  

voipH248LocalcallExistTime 1.1.890.1.5.13.5.16.10.5.2
The time to exist localcall utility after MGC reconnected. 1~60, in unit of minutes
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..60  

voipCountryCodeParam 1.1.890.1.5.13.5.16.11
OBJECT IDENTIFIER    

law 1.1.890.1.5.13.5.16.11.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER alaw(0), ulaw(1)  

impedance 1.1.890.1.5.13.5.16.11.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

loopCurrent 1.1.890.1.5.13.5.16.11.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

taxType 1.1.890.1.5.13.5.16.11.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

ringFrequency 1.1.890.1.5.13.5.16.11.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ringAmplitude 1.1.890.1.5.13.5.16.11.6
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ringOnTime1 1.1.890.1.5.13.5.16.11.7
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ringOffTime1 1.1.890.1.5.13.5.16.11.8
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ringOnTime2 1.1.890.1.5.13.5.16.11.9
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ringOffTime2 1.1.890.1.5.13.5.16.11.10
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

flashMin 1.1.890.1.5.13.5.16.11.11
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

flashMax 1.1.890.1.5.13.5.16.11.12
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

breakMin 1.1.890.1.5.13.5.16.11.13
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

breakMax 1.1.890.1.5.13.5.16.11.14
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

makeMin 1.1.890.1.5.13.5.16.11.15
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

makeMax 1.1.890.1.5.13.5.16.11.16
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

interDigitMin 1.1.890.1.5.13.5.16.11.17
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

meterFrequency 1.1.890.1.5.13.5.16.11.18
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

meterOnTime 1.1.890.1.5.13.5.16.11.19
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

meterOffTime 1.1.890.1.5.13.5.16.11.20
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

cidType 1.1.890.1.5.13.5.16.11.21
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER during-ring(0), prior-ring(1)  

payloadType 1.1.890.1.5.13.5.16.11.22
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

firstTASType 1.1.890.1.5.13.5.16.11.23
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

secondTASType 1.1.890.1.5.13.5.16.11.24
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

firstTASInterval 1.1.890.1.5.13.5.16.11.25
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

secondTASInterval 1.1.890.1.5.13.5.16.11.26
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

startToRing 1.1.890.1.5.13.5.16.11.27
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dialTone 1.1.890.1.5.13.5.16.11.28
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

ringBackTone 1.1.890.1.5.13.5.16.11.29
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

busyTone 1.1.890.1.5.13.5.16.11.30
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

congestionTone 1.1.890.1.5.13.5.16.11.31
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

callWaitingTone1 1.1.890.1.5.13.5.16.11.32
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

callWaitingTone2 1.1.890.1.5.13.5.16.11.33
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

specialDialTone 1.1.890.1.5.13.5.16.11.34
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

howlerTone 1.1.890.1.5.13.5.16.11.35
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

warningTone 1.1.890.1.5.13.5.16.11.36
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

confirmationTone 1.1.890.1.5.13.5.16.11.37
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

holdingTone 1.1.890.1.5.13.5.16.11.38
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

numberUnobtainableTone 1.1.890.1.5.13.5.16.11.39
This object is supported by R5.05 and later versions.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

recallDialTone 1.1.890.1.5.13.5.16.11.40
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

specialInformationTone 1.1.890.1.5.13.5.16.11.41
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipPots 1.1.890.1.5.13.5.16.12
OBJECT IDENTIFIER    

voipPotsFlash 1.1.890.1.5.13.5.16.12.2
OBJECT IDENTIFIER    

voipPotsRingTable 1.1.890.1.5.13.5.16.12.1
This table is supported by R5.05 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipPotsRingEntry

voipPotsRingEntry 1.1.890.1.5.13.5.16.12.1.1
An entry in voipPotsRingEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipPotsRingEntry  

voipPotsRingConfId 1.1.890.1.5.13.5.16.12.1.1.1
index
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipPotsRingConfNameDefval 1.1.890.1.5.13.5.16.12.1.1.2
Configure pots ring name to use default value. 1 : enable 2 : disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

voipPotsRingConfName 1.1.890.1.5.13.5.16.12.1.1.3
name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

voipPotsRingConfPatternDefval 1.1.890.1.5.13.5.16.12.1.1.4
Configure pots ring pattern to use default value. 1 : enable 2 : disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

voipPotsRingConfPatternOn1 1.1.890.1.5.13.5.16.12.1.1.5
first on time
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipPotsRingConfPatternOff1 1.1.890.1.5.13.5.16.12.1.1.6
first off time
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipPotsRingConfPatternOn2 1.1.890.1.5.13.5.16.12.1.1.7
second on time
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipPotsRingConfPatternOff2 1.1.890.1.5.13.5.16.12.1.1.8
second off time
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipPotsRingConfPatternOn3 1.1.890.1.5.13.5.16.12.1.1.9
third on time
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipPotsRingConfPatternOff3 1.1.890.1.5.13.5.16.12.1.1.10
third off time
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipPotsFlashDefval 1.1.890.1.5.13.5.16.12.2.1
Configure pots flash to use default setting. 1 : enable 2 : disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

voipPotsFlashMinTime 1.1.890.1.5.13.5.16.12.2.2
Minimum time of hook-flash detection period.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipPotsFlashMaxTime 1.1.890.1.5.13.5.16.12.2.3
Maximum time of hook-flash detection period.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipPotsRingVoltage 1.1.890.1.5.13.5.16.12.3
The ring output voltage of pots 25~90, in unit of Vrms. 0 means set to default value.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 25..90  

voipIfindexMap 1.1.890.1.5.13.5.16.13
OBJECT IDENTIFIER    

voipInterfaceMapTable 1.1.890.1.5.13.5.16.13.1
A list of interface entries map voip interface indexes to interface indexes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipInterfaceMapEntry

voipInterfaceMapEntry 1.1.890.1.5.13.5.16.13.1.1
An entry in voipInterfaceMapTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipInterfaceMapEntry  

voipIfIndex 1.1.890.1.5.13.5.16.13.1.1.1
voip index interface
Status: current Access: not-accessible
OBJECT-TYPE    
  InterfaceIndex  

ifIndexValue 1.1.890.1.5.13.5.16.13.1.1.2
Mapped interface index value for a voip interface index.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

voipIfTable 1.1.890.1.5.13.5.16.13.2
A list of interface entries map interface indexes to voip interface indexes.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipIfEntry

voipIfEntry 1.1.890.1.5.13.5.16.13.2.1
An entry in voipData2PotsIndexMapEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipIfEntry  

voipIfIndexValue 1.1.890.1.5.13.5.16.13.2.1.1
Mapped voip interface index value for a interface index.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

voipSingleIp 1.1.890.1.5.13.5.16.14
OBJECT IDENTIFIER    

voipExtH248 1.1.890.1.5.13.5.16.14.1
OBJECT IDENTIFIER    

voipExtStats 1.1.890.1.5.13.5.16.14.2
OBJECT IDENTIFIER    

voipExtSipProfile 1.1.890.1.5.13.5.16.14.3
OBJECT IDENTIFIER    

voipExtSip 1.1.890.1.5.13.5.16.14.6
OBJECT IDENTIFIER    

voipExtH248InterfaceConf 1.1.890.1.5.13.5.16.14.1.1
OBJECT IDENTIFIER    

voipExtH248InterfaceConfMgName 1.1.890.1.5.13.5.16.14.1.1.1
MG name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipExtH248InterfaceConfMgEnable 1.1.890.1.5.13.5.16.14.1.1.2
Enable/disable MG.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

voipExtH248InterfaceConfH248Profile 1.1.890.1.5.13.5.16.14.1.1.3
H.248 profile name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipExtH248InterfaceConfPort 1.1.890.1.5.13.5.16.14.1.1.4
MG port number.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1025..65535  

voipExtH248InterfaceConfSignalIp 1.1.890.1.5.13.5.16.14.1.1.5
Signaling Ip
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

voipExtH248InterfaceConfSignalMasklen 1.1.890.1.5.13.5.16.14.1.1.6
Signaling network mask, 0~32
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipExtH248InterfaceConfSignalVid 1.1.890.1.5.13.5.16.14.1.1.7
1~4094
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

voipExtH248InterfaceConfMediaIp 1.1.890.1.5.13.5.16.14.1.1.8
Media Ip
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

voipExtH248InterfaceConfMediaMasklen 1.1.890.1.5.13.5.16.14.1.1.9
Media network mask, 0~32
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipExtH248InterfaceConfMediaVid 1.1.890.1.5.13.5.16.14.1.1.10
1~4094
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

voipExtH248InterfaceConfDnsIp 1.1.890.1.5.13.5.16.14.1.1.11
DNS Ip
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

voipExtH248InterfaceConfRegisterRetry 1.1.890.1.5.13.5.16.14.1.1.12
Register retry time interval, in unit of minute. range is 1 to 1440.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..1440  

voipExtH248InterfaceMaxNumOfVoipRoute 1.1.890.1.5.13.5.16.14.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipExtH248InterfaceRouteTable 1.1.890.1.5.13.5.16.14.1.3
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipExtH248InterfaceRouteEntry

voipExtH248InterfaceRouteEntry 1.1.890.1.5.13.5.16.14.1.3.1
An entry of voipExtH248InterfaceRouteTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipExtH248InterfaceRouteEntry  

voipExtH248InterfaceRouteIp 1.1.890.1.5.13.5.16.14.1.3.1.1
IP address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipExtH248InterfaceRouteGateway 1.1.890.1.5.13.5.16.14.1.3.1.2
Gateway IP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipExtH248InterfaceRouteMask 1.1.890.1.5.13.5.16.14.1.3.1.3
Network mask.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..32  

voipExtH248InterfaceRouteMetric 1.1.890.1.5.13.5.16.14.1.3.1.4
Metric number of the route.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..15  

voipExtH248InterfaceRouteRowStatus 1.1.890.1.5.13.5.16.14.1.3.1.5
This object is used to create a new entry or delete an existing entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

voipExtH248InterfaceStat 1.1.890.1.5.13.5.16.14.2.1
OBJECT IDENTIFIER    

voipExtH248InterfaceStatMgState 1.1.890.1.5.13.5.16.14.2.1.1
Mg State
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(1), registering(2), registered(3), unregistering(4), unregistered(5), inactivity-timeout(6), activity-back(7), disconnected(8), disabled-by-MGC(9)  

voipExtH248InterfaceStatPrimaryProtectionState 1.1.890.1.5.13.5.16.14.2.1.2
Primary Protection State
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER invalid(1), active(2), standby(3)  

voipExtH248InterfaceStatSecondaryProtectionState 1.1.890.1.5.13.5.16.14.2.1.3
Secondary Protection State
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER invalid(1), active(2), standby(3)  

voipExtH248InterfaceStatRedundantState 1.1.890.1.5.13.5.16.14.2.1.4
Redundant State
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER out-of-sync(1), authorization(2), synchronizing(3), in-service(4)  

voipExtH248InterfaceStatMgcIp 1.1.890.1.5.13.5.16.14.2.1.5
MGC IP address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipExtH248InterfaceStatMgH248Mac 1.1.890.1.5.13.5.16.14.2.1.6
The MAC used by megaco packets.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipExtH248InterfaceStatLocalcallStat 1.1.890.1.5.13.5.16.14.2.1.7
Local call state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inactive(1), active(2)  

voipExtH248MediaStatTable 1.1.890.1.5.13.5.16.14.2.2
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipExtH248MediaStatEntry

voipExtH248MediaStatEntry 1.1.890.1.5.13.5.16.14.2.2.1
An entry of voipExtH248MediaStatTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipExtH248MediaStatEntry  

voipExtH248MediaStatSlotId 1.1.890.1.5.13.5.16.14.2.2.1.1
Slot ID
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipExtH248MediaStatPortCount 1.1.890.1.5.13.5.16.14.2.2.1.2
port count
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipExtH248MediaStatState 1.1.890.1.5.13.5.16.14.2.2.1.3
state
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unregistered(1), registered(2), invalid(3), unknown(4)  

voipExtH248TerminationStatTable 1.1.890.1.5.13.5.16.14.2.3
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipExtH248TerminationStatEntry

voipExtH248TerminationStatEntry 1.1.890.1.5.13.5.16.14.2.3.1
An entry of voipExtH248TerminationStatStateTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipExtH248TerminationStatEntry  

voipExtH248TerminationStatStateSlotId 1.1.890.1.5.13.5.16.14.2.3.1.1
Media Card Id of the termination.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipExtH248TerminationStatStatePortNumber 1.1.890.1.5.13.5.16.14.2.3.1.2
Port number the termination.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipExtH248TerminationStatName 1.1.890.1.5.13.5.16.14.2.3.1.3
Termination Name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

voipExtH248TerminationStatPhoneState 1.1.890.1.5.13.5.16.14.2.3.1.4
Phone State
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), on-hook(2), off-hook(3), ringing(4), testing(5), power-cut-down(6), fault(7), bad(8), uninitialized(9), unknown(10)  

voipExtH248TerminationStatCallServiceState 1.1.890.1.5.13.5.16.14.2.3.1.5
Call Service State
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), out-of-service(2), idle(3), waiting-for-dialing(4), dialing-out(5), ringing(6), conversation-caller(7), conversation-callee(8), fax-modem-caller(9), fax-modem-callee(10), waiting-for-on-hook(13), dialing-timeout(14), alerting-off-hook(15), power-cut-down(16), unknown(17)  

voipExtH248TerminationStatQuery 1.1.890.1.5.13.5.16.14.2.4
OBJECT IDENTIFIER    

voipExtH248TerminationStatQueryTerminationName 1.1.890.1.5.13.5.16.14.2.4.1
Termination Name
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipExtH248TerminationStatQuerySlotId 1.1.890.1.5.13.5.16.14.2.4.2
Slot Id
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipExtH248TerminationStatQueryPortNumber 1.1.890.1.5.13.5.16.14.2.4.3
Port Number
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipExtH248TerminationStatQueryPhoneState 1.1.890.1.5.13.5.16.14.2.4.4
Phone State
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), on-hook(2), off-hook(3), ringing(4), testing(5), power-cut-down(6), fault(7), bad(8), uninitialized(9), unknown(10)  

voipExtH248TerminationStatQueryCallServiceState 1.1.890.1.5.13.5.16.14.2.4.5
CallService State
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), out-of-service(2), idle(3), waiting-for-dialing(4), ringing(5), conversation-caller(6), conversation-callee(7), fax-modem-caller(8), fax-modem-callee(9), waiting-for-on-hook(12), dialing-timeout(13), alerting-off-hook(14), power-cut-down(15)  

voipExtMaxNumOfSipProfiles 1.1.890.1.5.13.5.16.14.3.1
The maximum number of SIP profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipExtSipProfileTable 1.1.890.1.5.13.5.16.14.3.2
This table includes SIP protocol related configuration. This table is supported by R4.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipExtSipProfileEntry

voipExtSipProfileEntry 1.1.890.1.5.13.5.16.14.3.2.1
An entry in voipExtSipProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipExtSipProfileEntry  

voipExtSipProfileName 1.1.890.1.5.13.5.16.14.3.2.1.1
This object is used by the SIP profile table in order to identify a row of this table.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipExtSipProfileSipSvr 1.1.890.1.5.13.5.16.14.3.2.1.2
IP used for SIP registration or SIP domain name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

voipExtSipProfileRegSvr 1.1.890.1.5.13.5.16.14.3.2.1.3
Registration server IP or registration server domain name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

voipExtSipProfileProxySvr 1.1.890.1.5.13.5.16.14.3.2.1.4
Proxy server IP or proxy server doamin name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

voipExtSipProfileSipPort 1.1.890.1.5.13.5.16.14.3.2.1.5
SIP UA port number.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1025..65535  

voipExtSipProfileRegSvrPort 1.1.890.1.5.13.5.16.14.3.2.1.6
Registration server port number.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1025..65535  

voipExtSipProfileProxySvrPort 1.1.890.1.5.13.5.16.14.3.2.1.7
Proxy server port number.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1025..65535  

voipExtSipProfilePbit 1.1.890.1.5.13.5.16.14.3.2.1.8
802.1p bit for SIP and RTP packet.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

voipExtSipProfileDscp 1.1.890.1.5.13.5.16.14.3.2.1.9
DSCP for SIP and RTP packet.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..63  

voipExtSipProfileKeepAlive 1.1.890.1.5.13.5.16.14.3.2.1.10
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

voipExtSipProfilePrack 1.1.890.1.5.13.5.16.14.3.2.1.11
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

voipExtSipProfileSe 1.1.890.1.5.13.5.16.14.3.2.1.12
Session expiration time in seconds.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 90..65535  

voipExtSipProfileSwitchType 1.1.890.1.5.13.5.16.14.3.2.1.13
Switch type
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER default(0), nsn(1), alu(2)  

voipExtSipProfileRtpStartPort 1.1.890.1.5.13.5.16.14.3.2.1.14
start of RTP port number. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

voipExtSipProfileRtpEndPort 1.1.890.1.5.13.5.16.14.3.2.1.15
end of RTP port number. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

voipExtSipProfileRegistrationExpire 1.1.890.1.5.13.5.16.14.3.2.1.16
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

voipExtSipProfileRegistrationExpireTime 1.1.890.1.5.13.5.16.14.3.2.1.17
registration expiration time under registered state, 120~65535 seconds
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

voipExtSipProfileRegistrationRetryTime 1.1.890.1.5.13.5.16.14.3.2.1.18
registration retry time under un-registered state, 120~900 seconds
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

voipExtSipProfileRowStatus 1.1.890.1.5.13.5.16.14.3.2.1.19
This object is used to create a new row or delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

voipExtSipProfilePrefixAddDigits 1.1.890.1.5.13.5.16.14.3.2.1.20
The prefix digits add before tel number
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipExtMaxNumOfSipCallSvcProfiles 1.1.890.1.5.13.5.16.14.3.3
The maximum number of SIP call service profiles supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipExtSipCallSvcProfileTable 1.1.890.1.5.13.5.16.14.3.4
This table includes SIP call service related configuration. This table is supported by R4.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipExtSipCallSvcProfileEntry

voipExtSipCallSvcProfileEntry 1.1.890.1.5.13.5.16.14.3.4.1
An entry in sipCallSvcProfileTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipExtSipCallSvcProfileEntry  

voipExtSipCallSvcProfileName 1.1.890.1.5.13.5.16.14.3.4.1.1
This object is used by the SIP call service profile table in order to identify a row of this table.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipExtSipCallSvcProfileKeypattern 1.1.890.1.5.13.5.16.14.3.4.1.2
Key pattern table name. This object is supported by R5.01 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipExtSipCallSvcProfileDialPlanOn 1.1.890.1.5.13.5.16.14.3.4.1.3
Please set CC, NDC, and dialplan table first.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

voipExtSipCallSvcProfileDialPlanCc 1.1.890.1.5.13.5.16.14.3.4.1.4
Country code, only digit 0..9 are allowed.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..7)  

voipExtSipCallSvcProfileDialPlanNdc 1.1.890.1.5.13.5.16.14.3.4.1.5
National destination code, only digit 0..9 are allowed.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..7)  

voipExtSipCallSvcProfileDialPlanTable 1.1.890.1.5.13.5.16.14.3.4.1.6
Numbering plan table name.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipExtSipCallSvcProfileDndOn 1.1.890.1.5.13.5.16.14.3.4.1.7
Do not Distrurb.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

voipExtSipCallSvcProfileDtmf 1.1.890.1.5.13.5.16.14.3.4.1.8
dtmf bypass : bypass DTMF tone dtmf rfc2833 : DTMF tone relay according to RFC2833 dtmf rfc2833like : DTMF tone relay by SIP INFO message, but RFC2833 payload dtmf sipinfo : DTMF tone relay by SIP INFO signal message dtmf plaintext : DTMF tone relay by SIP INFO plain text message
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER bypass(1), rfc2833(2), rfc2833like(3), sipinfo(4), plaintext(5)  

voipExtSipCallSvcProfileDtmfRfc2833Payload 1.1.890.1.5.13.5.16.14.3.4.1.9
dtmf rfc2833 payload type, 96~100
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

voipExtSipCallSvcProfileCallWaitOn 1.1.890.1.5.13.5.16.14.3.4.1.11
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

voipExtSipCallSvcProfileClipOn 1.1.890.1.5.13.5.16.14.3.4.1.12
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

voipExtSipCallSvcProfileClirOn 1.1.890.1.5.13.5.16.14.3.4.1.13
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

voipExtSipCallSvcProfileCallTransferOn 1.1.890.1.5.13.5.16.14.3.4.1.14
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

voipExtSipCallSvcProfileCallConferenceOn 1.1.890.1.5.13.5.16.14.3.4.1.15
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

voipExtSipCallSvcProfileFax 1.1.890.1.5.13.5.16.14.3.4.1.16
fax g711 : FAX service pass through by ITU-T G.711 fax t38 : FAX service by ITU-T T.38 UDP
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER g711(1), t38(2)  

voipExtSipCallSvcProfileFirstDigit 1.1.890.1.5.13.5.16.14.3.4.1.17
first digit timeout. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

voipExtSipCallSvcProfileInterdigit 1.1.890.1.5.13.5.16.14.3.4.1.18
inter digit timeout. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

voipExtSipCallSvcProfileMatchdigit 1.1.890.1.5.13.5.16.14.3.4.1.19
match digit timeout. This MIB object is supported by R5.05 and later versions.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER  

voipExtSipCallSvcProfileFlash 1.1.890.1.5.13.5.16.14.3.4.1.20
flash invite : send SIP INVITE message flash rfc2833 : flash relay according to RFC2833 flash rfc2833like : flash relay by SIP INFO message, but RFC2833 payload flash sipinfo1 : flash relay by SIP INFO signal=16 message flash sipinfo2 : flash relay by SIP INFO signal=hf message flash sipinfo3 : flash relay by SIP INFO signal=hook-flash message flash sipinfo4 : flash relay by SIP INFO plain text message flash sipinfo5 : flash relay by multiple SIP INFO signal messages and signal content come from specified pattern string flash sipinfo6 : flash relay by SIP INFO specified information message skip : no flash event, only onhook and offhook
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER invite(1), rfc2833(2), rfc2833like(3), sipinfo1(4), sipinfo2(5), sipinfo3(6), sipinfo4(7), sipinfo5(8), sipinfo6(9), skip(10)  

voipExtSipCallSvcProfileFlashPattern 1.1.890.1.5.13.5.16.14.3.4.1.21
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

voipExtSipCallSvcProfileLocalCallOn 1.1.890.1.5.13.5.16.14.3.4.1.22
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

voipExtSipCallSvcProfileMWIOn 1.1.890.1.5.13.5.16.14.3.4.1.23
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

voipExtSipCallSvcProfileCentrexOn 1.1.890.1.5.13.5.16.14.3.4.1.24
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER on(1), off(2)  

voipExtSipCallSvcProfileRowStatus 1.1.890.1.5.13.5.16.14.3.4.1.25
This object is used to create a new row or delete an existing row in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

voipExtSipCallSvcProfileLocalHelpTable 1.1.890.1.5.13.5.16.14.3.5
This table is supported by R5.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipExtSipCallSvcProfileLocalHelpEntry

voipExtSipCallSvcProfileLocalHelpEntry 1.1.890.1.5.13.5.16.14.3.5.1
An entry in sipCallSvcProfileLocalHelpTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipExtSipCallSvcProfileLocalHelpEntry  

voipExtSipCallSvcProfileLocalHelpIndex 1.1.890.1.5.13.5.16.14.3.5.1.1
Index number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

voipExtSipCallSvcProfileLocalHelpTableName 1.1.890.1.5.13.5.16.14.3.5.1.2
Local help table name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipExtSipCallSvcProfileLocalHelpTableTel 1.1.890.1.5.13.5.16.14.3.5.1.3
Local help telephone number. Only digit characters are allowed. Note that sipCallSvcProfileLocalHelpTableName and sipCallSvcProfileLocalHelpTableTel must be set sequentially.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..15)  

voipExtMaxNumOfVoipDialPlan 1.1.890.1.5.13.5.16.14.4
The maximum number of VoIP dial plan supported by the system.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipExtDialPlanTable 1.1.890.1.5.13.5.16.14.5
Configure dialing plan entry of specified index in specified payphone charging table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipExtDialPlanEntry

voipExtDialPlanEntry 1.1.890.1.5.13.5.16.14.5.1
An entry of voipExtDialPlanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipExtDialPlanEntry  

voipExtDialPlanName 1.1.890.1.5.13.5.16.14.5.1.1
Dialing plan table name.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipExtDialPlanIndex 1.1.890.1.5.13.5.16.14.5.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

voipExtDialPlanPattern 1.1.890.1.5.13.5.16.14.5.1.3
up to 47 characters, allow digit, '*', and '#' characters and meaning characters that include 'x', '.', '|' and range format characters that include '~', ',' and parenthesis '(', ')' and brackets '[', ']' and at most one parenthesis pair, examples: '002(x.)', '0(x.)', and '(x.)'
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..47)  

voipExtDialPlanRule 1.1.890.1.5.13.5.16.14.5.1.4
Allowed characters are 0~9, and '\c' stand for country code, '\d' stand for national destination code, '' stand for matched string enclosed by the parenthesis pair, and 'deny' stand for the pattern specified is not allowed. Examples: '', '\c', and '\c\d'.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..15)  

voipExtDialPlanRowStatus 1.1.890.1.5.13.5.16.14.5.1.5
This object is used to create a new entry or delete an existing entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

voipExtSipIp 1.1.890.1.5.13.5.16.14.6.1
OBJECT IDENTIFIER    

voipExtSipSignalIp 1.1.890.1.5.13.5.16.14.6.1.1
Signaling Ip
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

voipExtSipSignalMask 1.1.890.1.5.13.5.16.14.6.1.2
Signaling network mask, 0~32
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipExtSipSignalVid 1.1.890.1.5.13.5.16.14.6.1.3
1~4094
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

voipExtSipMediaIp 1.1.890.1.5.13.5.16.14.6.1.4
RTP IP
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

voipExtSipMediaMask 1.1.890.1.5.13.5.16.14.6.1.5
RTP network mask, 0~32
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipExtSipMediaVid 1.1.890.1.5.13.5.16.14.6.1.6
1~4094
Status: current Access: read-write
OBJECT-TYPE    
  VlanIndex  

voipExtSipDnsIp 1.1.890.1.5.13.5.16.14.6.1.7
Primary DNS IP. Set to '0.0.0.0' will clear both voipExtSipDnsIp and voipExtSipDnsIp2
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

voipExtSipDnsIp2 1.1.890.1.5.13.5.16.14.6.1.8
Secondary DNS IP. could not be set when voipExtSipDnsIp is '0.0.0.0', set voipExtSipDnsIp or voipExtSipDnsIp2 with '0.0.0.0' to clear.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

voipExtSipMaxNumOfVoipRoute 1.1.890.1.5.13.5.16.14.6.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

voipExtSipRouteTable 1.1.890.1.5.13.5.16.14.6.3
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipExtSipRouteEntry

voipExtSipRouteEntry 1.1.890.1.5.13.5.16.14.6.3.1
An entry of voipExtSipRouteTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipExtSipRouteEntry  

voipExtSipRouteIp 1.1.890.1.5.13.5.16.14.6.3.1.1
IP address.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipExtSipRouteGateway 1.1.890.1.5.13.5.16.14.6.3.1.2
Gateway IP.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

voipExtSipRouteMask 1.1.890.1.5.13.5.16.14.6.3.1.3
Network mask.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..32  

voipExtSipRouteMetric 1.1.890.1.5.13.5.16.14.6.3.1.4
Metric number of the route.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..15  

voipExtSipRouteRowStatus 1.1.890.1.5.13.5.16.14.6.3.1.5
This object is used to create a new entry or delete an existing entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

voipExtSipRegcount 1.1.890.1.5.13.5.16.14.6.4
register times per second, 1~255. 0 means off.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

voipExtSipCptReorder 1.1.890.1.5.13.5.16.14.6.5
Timeout of re-order tone, 5~300
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 5..300  

voipExtSipCptHowler 1.1.890.1.5.13.5.16.14.6.6
Timeout of re-order tone, 5~300
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 5..300  

voipExtSipCptAlerting 1.1.890.1.5.13.5.16.14.6.7
Timeout of re-order tone, 60~1200
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 60..1200  

voipExtSipPktLog 1.1.890.1.5.13.5.16.14.6.8
SIP packet log on/off
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

voipExtSipPktLogClear 1.1.890.1.5.13.5.16.14.6.9
Set 1 to clear SIP packet log
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipExtSipLineConfTable 1.1.890.1.5.13.5.16.14.7
This table includes common attributes describing the VoIP line.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipExtSipLineConfEntry

voipExtSipLineConfEntry 1.1.890.1.5.13.5.16.14.7.1
An entry in voipExtSipLineConfTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipExtSipLineConfEntry  

voipExtSipLineConfHotlineOn 1.1.890.1.5.13.5.16.14.7.1.1
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

voipExtSipLineConfHotlineNo 1.1.890.1.5.13.5.16.14.7.1.2
only alphanumeric characters and '+' are allowed, or use two quotation marks () to clear the field. Note: '+' only is allowed at the first character
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

voipExtSipLineConfHotlineTimeout 1.1.890.1.5.13.5.16.14.7.1.3
0~255 seconds, 0 means dialling immediately.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

voipExtSipLineConfTax 1.1.890.1.5.13.5.16.14.7.1.4
metering mode
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER mode-disable(0), mode-12K(1), mode-16K(2), mode-reversal-12K(3), mode-reversal-16K(4), mode-reversal-steady(5), mode-reversal-pulse(6)  

voipExtSipLineStatusTable 1.1.890.1.5.13.5.16.14.8
The table displays VoIP line status. This table is supported by R4.01 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    VoipExtSipLineStatusEntry

voipExtSipLineStatusEntry 1.1.890.1.5.13.5.16.14.8.1
An entry of voipExtSipLineStatTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  VoipExtSipLineStatusEntry  

voipExtSipLineStatusFxsStatus 1.1.890.1.5.13.5.16.14.8.1.1
FXS status of the line.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), on-hook(2), off-hook(3), ringing(4), power-cut-down(5), testing(6), fault(7), bad(8), uninitialized(9)  

voipExtSipLineStatusServiceStatus 1.1.890.1.5.13.5.16.14.8.1.2
Service status of the line.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), out-of-service(2), idle(3), waiting-for-dialing(4), dialing-out(5), ringing(6), conversation-caller(7), conversation-callee(8), fax-modem-caller(9), fax-modem-callee(10), fax-modem-caller(11), fax-modem-callee(12), waiting-for-on-hook(13), dialing-timeout(14), alerting-off-hook(15), power-cut-down(16)  

voipExtSipLineStatusLocalcallStatus 1.1.890.1.5.13.5.16.14.8.1.3
Localcall status of the line.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER on(1), off(2)  

imaGroupChan 1.1.890.1.5.13.5.17.2
OBJECT IDENTIFIER    

imaGroupTable 1.1.890.1.5.13.5.17.1
This table is supported by R5.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ImaGroupEntry

imaGroupEntry 1.1.890.1.5.13.5.17.1.1
An entry of imaGroupTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ImaGroupEntry  

imaGroupIndex 1.1.890.1.5.13.5.17.1.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaGroupClkMode 1.1.890.1.5.13.5.17.1.1.2
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ctc-loop(1), ctc-local(2), itc(3)  

imaGroupVersion 1.1.890.1.5.13.5.17.1.1.3
Tok_String
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER version-1-0(1), version-1-1(2)  

imaGroupChanNumTable 1.1.890.1.5.13.5.17.2.1
This table is supported by R5.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ImaGroupChanNumEntry

imaGroupChanNumEntry 1.1.890.1.5.13.5.17.2.1.1
An entry of ImaGroupChanNumTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ImaGroupChanNumEntry  

imaGroupChanNumSlot 1.1.890.1.5.13.5.17.2.1.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaGroupChanNumMaximum 1.1.890.1.5.13.5.17.2.1.1.2
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaGroupChanNumCurrentTotal 1.1.890.1.5.13.5.17.2.1.1.3
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaGroupChanNumCurrentPvc 1.1.890.1.5.13.5.17.2.1.1.4
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaGroupChanNumCurrentDtpvc 1.1.890.1.5.13.5.17.2.1.1.5
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaGroupPvcTable 1.1.890.1.5.13.5.17.2.2
This table includes IMA Group PVC configuration. This table is supported by R5.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ImaGroupPvcEntry

imaGroupPvcEntry 1.1.890.1.5.13.5.17.2.2.1
An entry of imaGroupPvcTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ImaGroupPvcEntry  

imaGroupPvcGroupIndex 1.1.890.1.5.13.5.17.2.2.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaGroupPvcVpi 1.1.890.1.5.13.5.17.2.2.1.2
VPI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

imaGroupPvcVci 1.1.890.1.5.13.5.17.2.2.1.3
VCI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

imaGroupPvcPvid 1.1.890.1.5.13.5.17.2.2.1.4
PVID of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

imaGroupPvcEncap 1.1.890.1.5.13.5.17.2.2.1.5
Encapsulation of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER llc(1), vc(2)  

imaGroupPvcPriority 1.1.890.1.5.13.5.17.2.2.1.6
priority of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

imaGruopPvcProfile 1.1.890.1.5.13.5.17.2.2.1.7
The value of this object identifies the row in the atmProfileTable, which applies for this pvc.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

imaGroupPvcRowStatus 1.1.890.1.5.13.5.17.2.2.1.8
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

imaGroupPvcEgressTag 1.1.890.1.5.13.5.17.2.2.1.9
Encapsulation of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER tag(1), untag(2)  

imaGroupDtPvcTable 1.1.890.1.5.13.5.17.2.3
This table includes IMA Group Double Tagging PVC configuration. This table is supported by R5.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ImaGroupDtPvcEntry

imaGroupDtPvcEntry 1.1.890.1.5.13.5.17.2.3.1
An entry of imaGroupDtPvcTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ImaGroupDtPvcEntry  

imaGroupDTPvcGroupIndex 1.1.890.1.5.13.5.17.2.3.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaGroupDtPvcVpi 1.1.890.1.5.13.5.17.2.3.1.2
VPI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

imaGroupDtPvcVci 1.1.890.1.5.13.5.17.2.3.1.3
VCI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

imaGroupDtPvcSvid 1.1.890.1.5.13.5.17.2.3.1.4
s-tag of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

imaGroupDtPvcCvid 1.1.890.1.5.13.5.17.2.3.1.5
c-tag of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

imaGroupDtPvcEncap 1.1.890.1.5.13.5.17.2.3.1.6
Encapsulation of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER llc(1), vc(2)  

imaGroupDtPvcSPriority 1.1.890.1.5.13.5.17.2.3.1.7
s-priority of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

imaGroupDtPvcCPriority 1.1.890.1.5.13.5.17.2.3.1.8
c-priority of the pvc.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..7  

imaGroupDtPvcProfile 1.1.890.1.5.13.5.17.2.3.1.9
The value of this object identifies the row in the atmProfileTable, which applies for this pvc.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..31)  

imaGroupDtPvcRowStatus 1.1.890.1.5.13.5.17.2.3.1.10
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

imaMgmtPvcTable 1.1.890.1.5.13.5.17.3
This table includes IMA Management PVC configuration. This table is supported by R5.03 and later versions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ImaMgmtPvcEntry

imaMgmtPvcEntry 1.1.890.1.5.13.5.17.3.1
An entry of imaMgmtPvcTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ImaMgmtPvcEntry  

imaMgmtPvcGroupIndex 1.1.890.1.5.13.5.17.3.1.1
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

imaMgmtPvcVpi 1.1.890.1.5.13.5.17.3.1.2
VPI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

imaMgmtPvcVci 1.1.890.1.5.13.5.17.3.1.3
VCI of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

imaMgmtPvcPvid 1.1.890.1.5.13.5.17.3.1.4
PVID of the pvc.
Status: current Access: read-only
OBJECT-TYPE    
  VlanIndex  

imaMgmtPvcEncap 1.1.890.1.5.13.5.17.3.1.5
Encapsulation of the pvc.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER llc(1), vc(2)  

imaMgmtPvcPriority 1.1.890.1.5.13.5.17.3.1.6
priority of the pvc.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..7  

imaMgmtPvcProfile 1.1.890.1.5.13.5.17.3.1.7
The value of this object identifies the row in the atmProfileTable, which applies for this pvc.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..31)  

imaMgmtPvcRowStatus 1.1.890.1.5.13.5.17.3.1.8
This object is used to create a new row or delete an existing row in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

imaMgmtPvcManagedIp 1.1.890.1.5.13.5.17.3.1.9
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

imaMgmtPvcGatewayIp 1.1.890.1.5.13.5.17.3.1.10
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

object 1.1.890.1.5.13.5.12.1
OBJECT IDENTIFIER    

dsl 1.1.890.1.5.13.5.12.2
OBJECT IDENTIFIER    

equipment 1.1.890.1.5.13.5.12.3
OBJECT IDENTIFIER    

systrap 1.1.890.1.5.13.5.12.4
OBJECT IDENTIFIER    

enet 1.1.890.1.5.13.5.12.5
OBJECT IDENTIFIER    

interface 1.1.890.1.5.13.5.12.6
OBJECT IDENTIFIER    

tdm 1.1.890.1.5.13.5.12.7
OBJECT IDENTIFIER    

voiptrap 1.1.890.1.5.13.5.12.8
OBJECT IDENTIFIER    

eqpt48VPowerIndex 1.1.890.1.5.13.5.12.1.1
The index of DC 48V power supply.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

eqptAlarmInputIndex 1.1.890.1.5.13.5.12.1.2
The index of alarm input.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

eqptDslDeviceIndex 1.1.890.1.5.13.5.12.1.3
The index of DSL device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

eqptShdslSubDeviceIndex 1.1.890.1.5.13.5.12.1.4
The sub-device index of SHDSL device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sysUser 1.1.890.1.5.13.5.12.1.5
The user capable of administering this NE with different priority level.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

sysAccessPoint 1.1.890.1.5.13.5.12.1.6
The access point to this NE.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER console(1), telnet(2), ftp(3), web(4), ssh(5)  

sysAccessPointIndex 1.1.890.1.5.13.5.12.1.7
The access point index to this NE.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sysUserLoginIp 1.1.890.1.5.13.5.12.1.8
The IP address from which the user login.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

eqptLTResetSource 1.1.890.1.5.13.5.12.1.9
The source that triggers LT reset.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER user(1), nt(2)  

sysProfSyncIpAddress 1.1.890.1.5.13.5.12.1.10
The server IP address to be synchronized or the client IP address to synchronize.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

sysMacAntiSpoofOrig 1.1.890.1.5.13.5.12.1.11
The original port of Mac-AntiSpoofing.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sysMacAntiSpoofNew 1.1.890.1.5.13.5.12.1.12
The new port of Mac-AntiSpoofing.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sysMacAntiSpoofMac 1.1.890.1.5.13.5.12.1.13
The mac address of Mac-AntiSpoofing.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

intfCfmCcmErrorCause 1.1.890.1.5.13.5.12.1.14
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noDefect(1), rdiReceived(2), macDownReceivedFromDownMEP(3), lostConnectionToRemoteMEP(4), configurationError(5), maintenanceDomainCrossConnect(6)  

e1AlarmStatus 1.1.890.1.5.13.5.12.1.15
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER set(1), clear(2)  

e1AlarmCurrentValue 1.1.890.1.5.13.5.12.1.16
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

e1AlarmThreshold 1.1.890.1.5.13.5.12.1.17
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dslMacAntiSpoofOrig 1.1.890.1.5.13.5.12.1.18
The original port of xDSL Mac-AntiSpoofing.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dslMacAntiSpoofMac 1.1.890.1.5.13.5.12.1.19
The mac address of xDSL Mac-AntiSpoofing.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

vopTermPhoneState 1.1.890.1.5.13.5.12.1.20
Phone Status
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), on-hook(1), off-hook(2), ringing(3), testing(4), power-cut-down(5), fault(6), bad(7), uninitialized(8), unknown(9)  

vopRingTimerSegment 1.1.890.1.5.13.5.12.1.21
Ring Timer Segment ID
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vopRingTimerId 1.1.890.1.5.13.5.12.1.22
Ring Timer ID
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vopDscCodecType 1.1.890.1.5.13.5.12.1.23
Codec Type
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER g711a(0), g711mu(1), g723(2), g726-16(3), g726-24(4), g726-32(5), g726-40(6), g729ab(7), unused(255)  

vopMcMediaId 1.1.890.1.5.13.5.12.1.24
Media Card ID
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vopMcPort 1.1.890.1.5.13.5.12.1.25
port number
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vopDropCallType 1.1.890.1.5.13.5.12.1.26
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER long-term(0), short-term(1)  

sysUserLoginInetAddrType 1.1.890.1.5.13.5.12.1.27
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

sysUserLoginInetAddr 1.1.890.1.5.13.5.12.1.28
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress  

vopDeviceId 1.1.890.1.5.13.5.12.1.29
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vopBatteryNum 1.1.890.1.5.13.5.12.1.30
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vopRingerShortCount 1.1.890.1.5.13.5.12.1.31
Tok_String
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

vopMgcIP 1.1.890.1.5.13.5.12.1.32
The IP address of Mgc.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

eqptSptMstiInstanceId 1.1.890.1.5.13.5.12.1.33
spanning tree msti instance number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

eqptSptPortStateOrig 1.1.890.1.5.13.5.12.1.34
The original port state of spanning tree .
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER discarding(0), learning(1), forwarding(2)  

eqptSptPortStateNew 1.1.890.1.5.13.5.12.1.35
The new port state of spanning tree.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER discarding(0), learning(1), forwarding(2)  

eqptSptPortRoleOrig 1.1.890.1.5.13.5.12.1.36
The original port role of spanning tree.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), alternated(1), backup(2), root(3), designated(4), master(5), nonStp(6)  

eqptSptPortRoleNew 1.1.890.1.5.13.5.12.1.37
The new port role of spanning tree.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), alternated(1), backup(2), root(3), designated(4), master(5), nonStp(6)  

dslLineEnable 1.1.890.1.5.13.5.12.2.1
The line is enabled by administrator.
Status: current Access: read-only
NOTIFICATION-TYPE    

dslLineDisable 1.1.890.1.5.13.5.12.2.2
The line is disabled by administrator.
Status: current Access: read-only
NOTIFICATION-TYPE    

dslLineBelowPlannedRate 1.1.890.1.5.13.5.12.2.3
The payload rate is below planned rate.
Status: current Access: read-only
NOTIFICATION-TYPE    

dslLineLdmStart 1.1.890.1.5.13.5.12.2.4
The line enters loop diagnosis mode.
Status: current Access: read-only
NOTIFICATION-TYPE    

dslLineLdmDone 1.1.890.1.5.13.5.12.2.5
The line exits loop diagnosis mode.
Status: current Access: read-only
NOTIFICATION-TYPE    

dslLinePowerDownL2 1.1.890.1.5.13.5.12.2.6
The line enters power down L2 mode.
Status: current Access: read-only
NOTIFICATION-TYPE    

dslLinePowerDownL0 1.1.890.1.5.13.5.12.2.7
The line enters power down L0 mode.
Status: current Access: read-only
NOTIFICATION-TYPE    

dslLineFailure 1.1.890.1.5.13.5.12.2.8
The line is failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

dslLineEnterTest 1.1.890.1.5.13.5.12.2.9
The line enters testing mode.
Status: current Access: read-only
NOTIFICATION-TYPE    

dslLineExitTest 1.1.890.1.5.13.5.12.2.10
The line exits testing mode.
Status: current Access: read-only
NOTIFICATION-TYPE    

dslLineVdslRateChange 1.1.890.1.5.13.5.12.2.12
This notification indicates VDSL link rate change.
Status: current Access: read-only
NOTIFICATION-TYPE    

dslLoopGuard 1.1.890.1.5.13.5.12.2.13
Loop guard is traggered.
Status: current Access: read-only
NOTIFICATION-TYPE    

dslMacAntiSpoof 1.1.890.1.5.13.5.12.2.14
xDsl MAC spoofing is traggered.
Status: current Access: read-only
NOTIFICATION-TYPE    

dslLineVturInfoReady 1.1.890.1.5.13.5.12.2.15
The vtur info is ready.
Status: current Access: read-only
NOTIFICATION-TYPE    

dslLineVturLpr 1.1.890.1.5.13.5.12.2.16
CPE is down.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqpt48VPowerFailure 1.1.890.1.5.13.5.12.3.1
The power supply of DC 48V is failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqpt48VPowerNormal 1.1.890.1.5.13.5.12.3.2
The power supply of DC 48V is normal.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptVoltageError 1.1.890.1.5.13.5.12.3.3
The voltage is abnormal.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptVoltageNormal 1.1.890.1.5.13.5.12.3.4
The voltage is normal.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptTempError 1.1.890.1.5.13.5.12.3.5
The temperature is abnormal.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptTempNormal 1.1.890.1.5.13.5.12.3.6
The temperature is normal.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptFanError 1.1.890.1.5.13.5.12.3.7
The fan RPM is abnormal.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptFanNormal 1.1.890.1.5.13.5.12.3.8
The fan RPM is normal.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptTempLowFanStop 1.1.890.1.5.13.5.12.3.9
The fan is stopped due to low temperature.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptHWMonitorFailure 1.1.890.1.5.13.5.12.3.10
Hardware monitor diagnosis is failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptExternalAlarmInput 1.1.890.1.5.13.5.12.3.11
External alarm input.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptTopologyChange 1.1.890.1.5.13.5.12.3.12
The change of spanning tree topology is detected.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptFWUploadOK 1.1.890.1.5.13.5.12.3.13
Uploading firmware is completed.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptFWUploadFailure 1.1.890.1.5.13.5.12.3.14
Uploading firmware is failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptLTPlugIn 1.1.890.1.5.13.5.12.3.15
LT is plugged in.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptLTPullOut 1.1.890.1.5.13.5.12.3.16
LT is pulled out.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptLTActive 1.1.890.1.5.13.5.12.3.17
LT is active.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptLTInactive 1.1.890.1.5.13.5.12.3.18
LT is inactive.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptLTFWUploadOK 1.1.890.1.5.13.5.12.3.19
Uploading firmware to LT is completed.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptLTFWUploadFailure 1.1.890.1.5.13.5.12.3.20
Uploading firmware to LT is failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptLTDslDeviceFailure 1.1.890.1.5.13.5.12.3.21
LT DSL device is failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptLTDslDeviceRedownload 1.1.890.1.5.13.5.12.3.22
The firmware of LT DSL device is re-downloaded.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptLTShdslDeviceRedownload 1.1.890.1.5.13.5.12.3.23
The firmware of LT DSL device is re-downloaded.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptLTEnable 1.1.890.1.5.13.5.12.3.24
LT is enabled.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptLTDisable 1.1.890.1.5.13.5.12.3.25
LT is disabled.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptLTReset 1.1.890.1.5.13.5.12.3.26
LT is reset.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptExternalAlarmInputRelease 1.1.890.1.5.13.5.12.3.27
External alarm input is released.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptNTSwitchOK 1.1.890.1.5.13.5.12.3.28
The trap signifies that MSC card is switched over successfully. The value of slotId is the slot ID of the current working MSC.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptCpuUtilizationHigh 1.1.890.1.5.13.5.12.3.29
The CPU utilization is over its high threshold.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptCpuUtilizationNormal 1.1.890.1.5.13.5.12.3.30
The CPU utilization is normal.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptPacketBufferUsageHigh 1.1.890.1.5.13.5.12.3.31
The packet buffer usage is over its high threshold.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptPacketBufferUsageNormal 1.1.890.1.5.13.5.12.3.32
The packet buffer usage is normal.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptMemoryUsageHigh 1.1.890.1.5.13.5.12.3.33
The memory usage is over its high threshold.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptMemoryUsageNormal 1.1.890.1.5.13.5.12.3.34
The memory usage is normal.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptDbInactive 1.1.890.1.5.13.5.12.3.35
The control card daughter board is inactive.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptDbNormal 1.1.890.1.5.13.5.12.3.36
The control card daughter board is normal.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptDbReset 1.1.890.1.5.13.5.12.3.37
The control card daughter board is reset.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptSptPortStateChange 1.1.890.1.5.13.5.12.3.38
The spanning tree msti port state change.
Status: current Access: read-only
NOTIFICATION-TYPE    

eqptSptPortRoleChange 1.1.890.1.5.13.5.12.3.39
The spanning tree msti port role change.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysReboot 1.1.890.1.5.13.5.12.4.1
System reboot.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysConfigChange 1.1.890.1.5.13.5.12.4.2
System configuration is changed.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysConfigUploadOK 1.1.890.1.5.13.5.12.4.3
Uploading system configuration is completed.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysConfigUploadFailure 1.1.890.1.5.13.5.12.4.4
Uploading system configuration is failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysTimeSyncFailure 1.1.890.1.5.13.5.12.4.5
Synchronizing time with the time server is failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysAlarmCutoffEnable 1.1.890.1.5.13.5.12.4.6
Alarm cutoff is activated.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysAlarmClearEnable 1.1.890.1.5.13.5.12.4.7
Alarm clear is activated.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysLoginFailure 1.1.890.1.5.13.5.12.4.8
User login is failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysLogin 1.1.890.1.5.13.5.12.4.9
User logins.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysUserAdded 1.1.890.1.5.13.5.12.4.10
User added.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysUserDeleted 1.1.890.1.5.13.5.12.4.11
User deleted.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysUserModified 1.1.890.1.5.13.5.12.4.12
User modified.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysSvrSyncProfOK 1.1.890.1.5.13.5.12.4.13
Server synchronize profiles successfully.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysSvrSyncProfFail 1.1.890.1.5.13.5.12.4.14
Server failed to synchronize profiles to a client.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysCliSyncProfOK 1.1.890.1.5.13.5.12.4.15
Client synchronize profiles from server successfully.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysCliSyncProfFail 1.1.890.1.5.13.5.12.4.16
Client failed to synchronize profiles from server.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysMacAntiSpoofing 1.1.890.1.5.13.5.12.4.17
MAC Anti-spoofing.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysClusterMemberAdd 1.1.890.1.5.13.5.12.4.18
Cluster member is added.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysClusterMemberDelete 1.1.890.1.5.13.5.12.4.19
Cluster member is deleted.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysClusterMemberActive 1.1.890.1.5.13.5.12.4.20
Cluster member is active.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysClusterMemberInactive 1.1.890.1.5.13.5.12.4.21
Cluster member is inactive.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysLoginInet 1.1.890.1.5.13.5.12.4.22
User logins.
Status: current Access: read-only
NOTIFICATION-TYPE    

sysLoginFailureInet 1.1.890.1.5.13.5.12.4.23
User login is failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

enetEnable 1.1.890.1.5.13.5.12.5.1
Gigabit Ethernet interface is enabled.
Status: current Access: read-only
NOTIFICATION-TYPE    

enetDisable 1.1.890.1.5.13.5.12.5.2
Gigabit Ethernet interface is disabled.
Status: current Access: read-only
NOTIFICATION-TYPE    

enetLoopGuard 1.1.890.1.5.13.5.12.5.3
Loop guard is traggered.
Status: current Access: read-only
NOTIFICATION-TYPE    

enetSfpError 1.1.890.1.5.13.5.12.5.4
SFP DDMI parameters out of range.
Status: current Access: read-only
NOTIFICATION-TYPE    

enetSfpNormal 1.1.890.1.5.13.5.12.5.5
SFP DDMI parameters back to range.
Status: current Access: read-only
NOTIFICATION-TYPE    

enetSfpTxEnable 1.1.890.1.5.13.5.12.5.6
SFP TX power is enabled.
Status: current Access: read-only
NOTIFICATION-TYPE    

enetSfpTxDisable 1.1.890.1.5.13.5.12.5.7
SFP TX power is disabled.
Status: current Access: read-only
NOTIFICATION-TYPE    

cfmCcmError 3.1
Tok_String
Status: current Access: read-only
NOTIFICATION-TYPE    

e1AlarmLinkLOS 1.1.890.1.5.13.5.12.7.1
Tok_String
Status: current Access: read-only
NOTIFICATION-TYPE    

e1AlarmPathLOF 1.1.890.1.5.13.5.12.7.2
Tok_String
Status: current Access: read-only
NOTIFICATION-TYPE    

e1AlarmPathAIS 1.1.890.1.5.13.5.12.7.3
Tok_String
Status: current Access: read-only
NOTIFICATION-TYPE    

e1AlarmPathRDI 1.1.890.1.5.13.5.12.7.4
Tok_String
Status: current Access: read-only
NOTIFICATION-TYPE    

e1AlarmPathOCASMF 1.1.890.1.5.13.5.12.7.5
Tok_String
Status: current Access: read-only
NOTIFICATION-TYPE    

e1AlarmPathOCRCMF 1.1.890.1.5.13.5.12.7.6
Tok_String
Status: current Access: read-only
NOTIFICATION-TYPE    

e1AlarmLinkSF 1.1.890.1.5.13.5.12.7.7
Tok_String
Status: current Access: read-only
NOTIFICATION-TYPE    

e1AlarmLinkSD 1.1.890.1.5.13.5.12.7.8
Tok_String
Status: current Access: read-only
NOTIFICATION-TYPE    

e1AlarmTCAQuarterES 1.1.890.1.5.13.5.12.7.9
Tok_String
Status: current Access: read-only
NOTIFICATION-TYPE    

e1AlarmTCAQuarterSES 1.1.890.1.5.13.5.12.7.10
Tok_String
Status: current Access: read-only
NOTIFICATION-TYPE    

e1AlarmTCAQuarterUAS 1.1.890.1.5.13.5.12.7.11
Tok_String
Status: current Access: read-only
NOTIFICATION-TYPE    

e1AlarmTCADayES 1.1.890.1.5.13.5.12.7.12
Tok_String
Status: current Access: read-only
NOTIFICATION-TYPE    

e1AlarmTCADaySES 1.1.890.1.5.13.5.12.7.13
Tok_String
Status: current Access: read-only
NOTIFICATION-TYPE    

e1AlarmTCADayUAS 1.1.890.1.5.13.5.12.7.14
Tok_String
Status: current Access: read-only
NOTIFICATION-TYPE    

vopTempError 1.1.890.1.5.13.5.12.8.1
temperature out of low or high threshold
Status: current Access: read-only
NOTIFICATION-TYPE    

vopTempNormal 1.1.890.1.5.13.5.12.8.2
temperature normal
Status: current Access: read-only
NOTIFICATION-TYPE    

vopDCFail 1.1.890.1.5.13.5.12.8.3
DC power feed got problem
Status: current Access: read-only
NOTIFICATION-TYPE    

vopDCNormal 1.1.890.1.5.13.5.12.8.4
DC power feed normal
Status: current Access: read-only
NOTIFICATION-TYPE    

vopACFail 1.1.890.1.5.13.5.12.8.5
AC power feed got problem
Status: current Access: read-only
NOTIFICATION-TYPE    

vopACNormal 1.1.890.1.5.13.5.12.8.6
AC power feed normal
Status: current Access: read-only
NOTIFICATION-TYPE    

vopRingTimer 1.1.890.1.5.13.5.12.8.7
Ringer timer got problem
Status: current Access: read-only
NOTIFICATION-TYPE    

vopRingResource 1.1.890.1.5.13.5.12.8.8
Ringer electrical load exceed REN (Ring Equivalent number)
Status: current Access: read-only
NOTIFICATION-TYPE    

vopRingOverHead 1.1.890.1.5.13.5.12.8.9
High load indication of RI (Ring Indicator, control signal from modem to computer, indicate phone line is ringing)
Status: current Access: read-only
NOTIFICATION-TYPE    

vopNoFreeDSPChannel 1.1.890.1.5.13.5.12.8.10
DSP resource is not enough for voice processing
Status: current Access: read-only
NOTIFICATION-TYPE    

vopMCMissing 1.1.890.1.5.13.5.12.8.11
Signal Card detects Media Card missing
Status: current Access: read-only
NOTIFICATION-TYPE    

vopSCMissing 1.1.890.1.5.13.5.12.8.12
Media Card detects Signaling Card missing
Status: current Access: read-only
NOTIFICATION-TYPE    

vopTermNameDup 1.1.890.1.5.13.5.12.8.13
Duplicate termination name used
Status: current Access: read-only
NOTIFICATION-TYPE    

vopNoProtection 1.1.890.1.5.13.5.12.8.14
Can not find protection card on specified slot
Status: current Access: read-only
NOTIFICATION-TYPE    

vopProtectionSwitch 1.1.890.1.5.13.5.12.8.15
Signal Card protection switch happened
Status: current Access: read-only
NOTIFICATION-TYPE    

vopDropCall 1.1.890.1.5.13.5.12.8.16
Phone call exceed short / long term limit
Status: current Access: read-only
NOTIFICATION-TYPE    

vopBatteryFail 1.1.890.1.5.13.5.12.8.17
CODEC/SLIC module report Battery power failed
Status: current Access: read-only
NOTIFICATION-TYPE    

vopBatteryNormal 1.1.890.1.5.13.5.12.8.18
CODEC/SLIC module report Battery power normal
Status: current Access: read-only
NOTIFICATION-TYPE    

vopClockFail 1.1.890.1.5.13.5.12.8.19
VCP chip CLOCK failed or missing
Status: current Access: read-only
NOTIFICATION-TYPE    

vopClockNormal 1.1.890.1.5.13.5.12.8.20
VCP chip CLOCK normal
Status: current Access: read-only
NOTIFICATION-TYPE    

vopRingerFail 1.1.890.1.5.13.5.12.8.21
CODEC/SLIC module external ringer does not work
Status: current Access: read-only
NOTIFICATION-TYPE    

vopRingerNormal 1.1.890.1.5.13.5.12.8.22
CODEC/SLIC module external ringer work normal
Status: current Access: read-only
NOTIFICATION-TYPE    

vopMgcMissing 1.1.890.1.5.13.5.12.8.23
Indicate the state of mgc. Missing trap will be issue when mg had registered to mgc, and disconnected happened.
Status: current Access: read-only
NOTIFICATION-TYPE    

vopMgcNormal 1.1.890.1.5.13.5.12.8.24
Indicate the state of mgc. Normal trap will be issue when missing trap is not clear and mg registered to mgc again.
Status: current Access: read-only
NOTIFICATION-TYPE    

vopMgEnable 1.1.890.1.5.13.5.12.8.25
Indicate the state of mg. Mg enable trap will be issued when user enable the mg in manual.
Status: current Access: read-only
NOTIFICATION-TYPE    

vopMgDisable 1.1.890.1.5.13.5.12.8.26
Indicate the state of mg. Mg disable trap will be issued when user disable the mg in manual.
Status: current Access: read-only
NOTIFICATION-TYPE    

vopPortMissing 1.1.890.1.5.13.5.12.8.27
none.
Status: current Access: read-only
NOTIFICATION-TYPE    

vopPortNormal 1.1.890.1.5.13.5.12.8.28
none.
Status: current Access: read-only
NOTIFICATION-TYPE    

vopMcNormal 1.1.890.1.5.13.5.12.8.29
MC is normal.
Status: current Access: read-only
NOTIFICATION-TYPE    

vopScNormal 1.1.890.1.5.13.5.12.8.30
SC is normal.
Status: current Access: read-only
NOTIFICATION-TYPE    

vopScBulkSyncReady 1.1.890.1.5.13.5.12.8.31
SC bulk sync completed.
Status: current Access: read-only
NOTIFICATION-TYPE    

vopProtectionReady 1.1.890.1.5.13.5.12.8.32
SC redundancy is ready.
Status: current Access: read-only
NOTIFICATION-TYPE