ZTE-AN-ENVMON-MIB

File: ZTE-AN-ENVMON-MIB.mib (102520 bytes)

Imported modules

SNMPv2-TC SNMPv2-SMI ZTE-AN-SMI
SNMPv2-CONF HC-PerfHist-TC-MIB

Imported symbols

RowStatus DisplayString TruthValue
DateAndTime MODULE-IDENTITY OBJECT-TYPE
Integer32 IpAddress Counter64
Unsigned32 NOTIFICATION-TYPE zxAccessNode
zxAnEquipment MODULE-COMPLIANCE OBJECT-GROUP
NOTIFICATION-GROUP TEXTUAL-CONVENTION HCPerfCurrentCount

Defined Types

ZxAnEnvShutdownServiceType  
A set of service type defined in environment monitor module that may be shut down in protection action, each bit refers to a type: Bit 00 : xPON service. Bit 01 : xDSL service. Bit 02 : P2P service. Bit 03 : narrowband service.
TEXTUAL-CONVENTION    
  BITS xpon(0), xdsl(1), p2p(2), narrowband(3)  

ZxAnEnvParamEntry  
SEQUENCE    
  zxAnEnvRack Integer32
  zxAnEnvShelf Integer32
  zxAnEnvTemp Integer32
  zxAnEnvTempHighAlmThreshold Integer32
  zxAnEnvTempCriticalAlmThreshold Integer32
  zxAnEnvTempLowAlmThreshold Integer32
  zxAnEnvShelfPowerConsumption Integer32
  zxAnEnvShelfVoltage Integer32
  zxAnEnvShelfCurrent Integer32

ZxAnCardEnvParamEntry  
SEQUENCE    
  zxAnEnvSlot Integer32
  zxAnCardTemp Integer32
  zxAnCardPowerConsumption Integer32
  zxAnCardVoltage Integer32
  zxAnCardCurrent Integer32
  zxAnCardCriticalTempAlmThreshold Integer32
  zxAnCardOptHighestTemp Integer32
  zxAnCardOptCriticalTempAlmThresh Integer32
  zxAnCardOptHighestTempPortNo Integer32
  zxAnCardHeatRadiationAlmThresh Integer32
  zxAnCardTempHighAccuracy Integer32

ZxAnCardEnvHis15MinPerfEntry  
SEQUENCE    
  zxAnCardEnvHis15MinIntervalNo Integer32
  zxAnCardEnvHis15MinDateTime DateAndTime
  zxAnCardEnvHis15MinTemp Counter64

ZxAnCardEnvHis1DayPerfEntry  
SEQUENCE    
  zxAnCardEnvHis1DayIntervalNo Integer32
  zxAnCardEnvHis1DayDateTime DateAndTime
  zxAnCardEnvHis1DayTemp Counter64

ZxAnCardEnvAlmProfileConfEntry  
SEQUENCE    
  zxAnCardEnvAlmProfileName DisplayString
  zxAnCardEnvPerfVariable OBJECT IDENTIFIER
  zxAnCardEnvRiseAlmThresh HCPerfCurrentCount
  zxAnCardEnvClrRiseAlmThresh HCPerfCurrentCount
  zxAnCardEnvRiseWarnThresh HCPerfCurrentCount
  zxAnCardEnvClrRiseWarnThresh HCPerfCurrentCount
  zxAnCardEnvFallWarnThresh HCPerfCurrentCount
  zxAnCardEnvClrFallWarnThresh HCPerfCurrentCount
  zxAnCardEnvFallAlmThresh HCPerfCurrentCount
  zxAnCardEnvClrFallAlmThresh HCPerfCurrentCount
  zxAnCardEnvAlmPrfConfRowStatus RowStatus

ZxAnCardEnvAlmProfileApplyEntry  
SEQUENCE    
  zxAnCardEnvAlmPrf DisplayString
  zxAnCardEnvAlmPrfApplyRowStatus RowStatus

ZxAnCardEnvAlmProfileEntry  
SEQUENCE    
  zxAnCardEnvAlmPrfRowStatus RowStatus

ZxAnEnvOverheatProtectEntry  
SEQUENCE    
  zxAnEnvOverheatProtectEnable INTEGER
  zxAnEnvOverheatProtectDelay Integer32
  zxAnEnvOverheatProtectFirstStep ZxAnEnvShutdownServiceType
  zxAnEnvOverheatProtectSecondStep ZxAnEnvShutdownServiceType

ZxAnEnvCardOverheatProtectEntry  
SEQUENCE    
  zxAnEnvCardCriticalTempProtectEn INTEGER

ZxAnCardEnvHisMinPerfEntry  
SEQUENCE    
  zxAnCardEnvHMinIntervalNo Integer32
  zxAnCardEnvHMinIntervalValidData INTEGER
  zxAnCardEnvHMinDateTime DateAndTime
  zxAnCardEnvHMinTemperature Integer32
  zxAnCardEnvHMinVoltage Integer32
  zxAnCardEnvHMinPowerConsumption Integer32

ZxAnEnvMonInterfaceEntry  
SEQUENCE    
  zxAnEnvMonInterfaceUsage INTEGER
  zxAnEnvEpmConnectPort INTEGER
  zxAnEnvBackplaneInterfaceUsage INTEGER

ZxAnPowerSupplyCapabilityEntry  
SEQUENCE    
  zxAnPowerSupplyMaxPowerNum Integer32

ZxAnPowerSupplyEntry  
SEQUENCE    
  zxAnPowerSupplyOperStatus INTEGER
  zxAnPowerSupplyInVoltage Integer32
  zxAnPowerSupplyInVoltageStatus INTEGER
  zxAnPowerInVoltageUpperThresh Integer32
  zxAnPowerInVoltageLowerThresh Integer32
  zxAnPowerSupplyInCurrent Integer32
  zxAnPowerInCurrentThresh Integer32

ZxAnEnvEnergySavingEntry  
SEQUENCE    
  zxAnEnvEnergySavingRack Integer32
  zxAnEnvEnergySavingShelf Integer32
  zxAnEnvEnergySavingSlot Integer32
  zxAnEnvEnergySavingPort Integer32
  zxAnEnvEnergySavingStatus INTEGER
  zxAnEnvEnergySavingReason INTEGER
  zxAnEnvEnergySavingOccurringTime DateAndTime

ZxAnEnvFanTrayEntry  
SEQUENCE    
  zxAnFanTrayAlarmBeepEnable INTEGER
  zxAnFanTrayAutoSwitchByCardUp INTEGER
  zxAnFanTrayHardwareVersion DisplayString
  zxAnFanTraySoftwareVersion DisplayString
  zxAnFanTraySpeedCtrlMode INTEGER
  zxAnFanTrayLowSpeed Integer32
  zxAnFanTrayStdSpeed Integer32
  zxAnFanTrayHighSpeed Integer32
  zxAnFanTraySuperSpeed Integer32
  zxAnFanTrayLowSpeedShiftTemp Integer32
  zxAnFanTrayStdSpeedShiftTemp Integer32
  zxAnFanTrayHighSpeedShiftTemp Integer32
  zxAnFanTraySuperSpeedShiftTemp Integer32
  zxAnFanTrayLowSpeedPercent INTEGER
  zxAnFanTrayStdSpeedPercent INTEGER
  zxAnFanTrayHighSpeedPercent INTEGER
  zxAnFanTraySuperSpeedPercent INTEGER
  zxAnFanTrayAdminStatus INTEGER
  zxAnFanTrayConfSpeedLevel INTEGER
  zxAnFanTrayPowerConsumption Integer32
  zxAnFanTraySn DisplayString
  zxAnFanTrayVoltage Integer32
  zxAnFanTrayCurrent Integer32
  zxAnFanTrayTemp Integer32

ZxAnEnvFanEntry  
SEQUENCE    
  zxAnEnvFanIndex Integer32
  zxAnEnvFanConfSpeedLevel INTEGER
  zxAnEnvFanActualSpeedLevel INTEGER
  zxAnEnvFanAdminStatus INTEGER
  zxAnEnvFanOperStatus INTEGER
  zxAnEnvFanOnlineStatus INTEGER
  zxAnEnvFanActualSpeed Integer32

ZxAnEnvDeviceEntry  
SEQUENCE    
  zxAnEnvDeviceId Integer32
  zxAnEnvDeviceName DisplayString
  zxAnEnvDeviceRowStatus RowStatus

ZxAnEnvDevMonSwitchEntry  
SEQUENCE    
  zxAnEnvDevMonSwitchId Integer32
  zxAnEnvDevMonSwitchDeviceId Integer32
  zxAnEnvDevMonSwitchTrapEnable INTEGER
  zxAnEnvDevMonSwitchNormalStatus INTEGER
  zxAnEnvDevMonSwitchCurrStatus INTEGER

Defined Values

zxAnEnvMonMib 1.3.6.1.4.1.3902.1082.10.10
This MIB defines zte Access Node managed environment monitor.
MODULE-IDENTITY    

zxAnEnvMonGlobalObjects 1.3.6.1.4.1.3902.1082.10.10.1
OBJECT IDENTIFIER    

zxAnEnvMonObjects 1.3.6.1.4.1.3902.1082.10.10.2
OBJECT IDENTIFIER    

zxAnEnvMonNotifications 1.3.6.1.4.1.3902.1082.10.10.3
OBJECT IDENTIFIER    

zxAnEnvParamObjects 1.3.6.1.4.1.3902.1082.10.10.2.1
OBJECT IDENTIFIER    

zxAnEnvMonInterfaceObjects 1.3.6.1.4.1.3902.1082.10.10.2.2
OBJECT IDENTIFIER    

zxAnEnvPowerSupplyObjects 1.3.6.1.4.1.3902.1082.10.10.2.3
OBJECT IDENTIFIER    

zxAnEnvFanObjects 1.3.6.1.4.1.3902.1082.10.10.2.4
OBJECT IDENTIFIER    

zxAnEnvDeviceObjects 1.3.6.1.4.1.3902.1082.10.10.2.5
OBJECT IDENTIFIER    

zxAnEnvFanTrayResetObjects 1.3.6.1.4.1.3902.1082.10.10.2.4.12
OBJECT IDENTIFIER    

zxAnEnvParamGlobalObjects 1.3.6.1.4.1.3902.1082.10.10.2.1.1
OBJECT IDENTIFIER    

zxAnPowerSupplyGlobalObjects 1.3.6.1.4.1.3902.1082.10.10.2.3.1
OBJECT IDENTIFIER    

zxAnEnvMonTempTraps 1.3.6.1.4.1.3902.1082.10.10.3.1
OBJECT IDENTIFIER    

zxAnEnvMonInterfaceTraps 1.3.6.1.4.1.3902.1082.10.10.3.2
OBJECT IDENTIFIER    

zxAnEnvMonPowerSupplyTraps 1.3.6.1.4.1.3902.1082.10.10.3.3
OBJECT IDENTIFIER    

zxAnEnvMonFanTraps 1.3.6.1.4.1.3902.1082.10.10.3.4
OBJECT IDENTIFIER    

zxAnEnvDeviceTraps 1.3.6.1.4.1.3902.1082.10.10.3.5
OBJECT IDENTIFIER    

zxAnEnvMonCapabilities 1.3.6.1.4.1.3902.1082.10.10.1.1
The environment management capabilities of this equipment.The bit value 1 means the function represented by this bit is supported by this equipment. NOTE: Not recommended to display it in NMS.
Status: current Access: read-only
OBJECT-TYPE    
  BITS envTemperature(0), fanAlarmBeep(1), fanAutoSwitchByCardInstall(2), fanSpeedCtrlBasedTemperature(3), fanFixSpeed(4), singleFanShutdown(5), mpTemperature(6), powerSupply(7), cardTemperature(8), fanSpeedPercentage(9), backplaneInterface(10), envMonitorInterfaceTrapEnable(11), slaveShelfFanConfig(12)  

zxAnEnvCardShutdownReason 1.3.6.1.4.1.3902.1082.10.10.2.1.1.1
The alarm reason of zxAnEnvCardShutdownAlm. envHighTemperature(1): Environment temperature is too high. cardHighTemperature(2):Card self temperature is too high. chipHighTemperature(3):Card's chip temperature is too high. emergencyPowerSaving(4):Emergency power saving action has been taken caused by AC power failure.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER envHighTemperature(1), cardHighTemperature(2), chipHighTemperature(3), emergencyPowerSaving(4)  

zxAnEnvParamTable 1.3.6.1.4.1.3902.1082.10.10.2.1.5
This table includes environment temperature information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnEnvParamEntry

zxAnEnvParamEntry 1.3.6.1.4.1.3902.1082.10.10.2.1.5.1
The entry of zxAnEnvParamTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnEnvParamEntry  

zxAnEnvRack 1.3.6.1.4.1.3902.1082.10.10.2.1.5.1.1
The index of rack.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

zxAnEnvShelf 1.3.6.1.4.1.3902.1082.10.10.2.1.5.1.2
The index of shelf.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

zxAnEnvTemp 1.3.6.1.4.1.3902.1082.10.10.2.1.5.1.3
The temperature of the environment.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnEnvTempHighAlmThreshold 1.3.6.1.4.1.3902.1082.10.10.2.1.5.1.4
The temperature high alarm threshold of the environment.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 45..95  

zxAnEnvTempCriticalAlmThreshold 1.3.6.1.4.1.3902.1082.10.10.2.1.5.1.5
The temperature critical alarm threshold of the environment.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnEnvTempLowAlmThreshold 1.3.6.1.4.1.3902.1082.10.10.2.1.5.1.6
The temperature low alarm threshold of the environment.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -40..0  

zxAnEnvShelfPowerConsumption 1.3.6.1.4.1.3902.1082.10.10.2.1.5.1.7
Power consumption of the shelf. Value 0 means not available.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnEnvShelfVoltage 1.3.6.1.4.1.3902.1082.10.10.2.1.5.1.8
Voltage of the shelf. Value 0 means not available.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnEnvShelfCurrent 1.3.6.1.4.1.3902.1082.10.10.2.1.5.1.9
Current of the shelf. Value 0 means not available.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCardEnvParamTable 1.3.6.1.4.1.3902.1082.10.10.2.1.6
This table includes card temperature information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCardEnvParamEntry

zxAnCardEnvParamEntry 1.3.6.1.4.1.3902.1082.10.10.2.1.6.1
The entry of zxAnCardEnvParamTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCardEnvParamEntry  

zxAnEnvSlot 1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.1
The index of slot, the range is [0,20] of 19-inch shelf and [0,22] of 21-inch shelf.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

zxAnCardTemp 1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.2
The current temperature of the card environment. NOTE: 1. In current system, only certain cards support temperature-reading, such as SCXL, GTGOD cards. 2. If the card is not configured, we cannot get its temperature. 3. For the configured but not support temperature-reading cards, we use -1000 as an invalid temperature value to note its temperature.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCardPowerConsumption 1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.3
Power consumption of the card. Value 0 means not available.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCardVoltage 1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.4
Voltage of the card. Value 0 means not available.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCardCurrent 1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.5
Current of the card. Value 0 means not available.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCardCriticalTempAlmThreshold 1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.6
The critical temperature alarm threshold of the card.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

zxAnCardOptHighestTemp 1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.7
The highest temperature of the optical modules in the card.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

zxAnCardOptCriticalTempAlmThresh 1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.8
The critical optical temperature alarm threshold.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

zxAnCardOptHighestTempPortNo 1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.9
The port No. which the optical module is located at, and the optical module has the highest temperature.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

zxAnCardHeatRadiationAlmThresh 1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.10
The heat radiation abnormal alarm threshold of the card.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32  

zxAnCardTempHighAccuracy 1.3.6.1.4.1.3902.1082.10.10.2.1.6.1.11
The high accuracy value of zxAnCardTemp.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCardEnvHis15MinPerfTable 1.3.6.1.4.1.3902.1082.10.10.2.1.7
The 15 minutes interval performance data table of card temperature.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCardEnvHis15MinPerfEntry

zxAnCardEnvHis15MinPerfEntry 1.3.6.1.4.1.3902.1082.10.10.2.1.7.1
The 15 minutes interval performance data entry of card temperature.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCardEnvHis15MinPerfEntry  

zxAnCardEnvHis15MinIntervalNo 1.3.6.1.4.1.3902.1082.10.10.2.1.7.1.1
Performance data interval number 1 is the the most recent previous interval; interval 96 is 24 hours ago. Intervals 2..96 are optional.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..96  

zxAnCardEnvHis15MinDateTime 1.3.6.1.4.1.3902.1082.10.10.2.1.7.1.2
The 15 minutes interval performance data generation time.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

zxAnCardEnvHis15MinTemp 1.3.6.1.4.1.3902.1082.10.10.2.1.7.1.3
The 15 minutes interval average temperature of card.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

zxAnCardEnvHis1DayPerfTable 1.3.6.1.4.1.3902.1082.10.10.2.1.8
The 1 day interval performance data table of card temperature.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCardEnvHis1DayPerfEntry

zxAnCardEnvHis1DayPerfEntry 1.3.6.1.4.1.3902.1082.10.10.2.1.8.1
The 1 day interval performance data entry of card temperature.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCardEnvHis1DayPerfEntry  

zxAnCardEnvHis1DayIntervalNo 1.3.6.1.4.1.3902.1082.10.10.2.1.8.1.1
Performance data interval number 1 is the the most recent previous interval; interval 7 is 1 week ago. Intervals 2..7 are optional.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..7  

zxAnCardEnvHis1DayDateTime 1.3.6.1.4.1.3902.1082.10.10.2.1.8.1.2
The 1 day interval performance data generation time.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

zxAnCardEnvHis1DayTemp 1.3.6.1.4.1.3902.1082.10.10.2.1.8.1.3
The 1 day interval average temperature of card.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

zxAnCardEnvAlmProfileConfTable 1.3.6.1.4.1.3902.1082.10.10.2.1.9
The performance alarm threshold profile items configuration table of card temperature.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCardEnvAlmProfileConfEntry

zxAnCardEnvAlmProfileConfEntry 1.3.6.1.4.1.3902.1082.10.10.2.1.9.1
The performance alarm threshold profile items configuration entry of card temperature.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCardEnvAlmProfileConfEntry  

zxAnCardEnvAlmProfileName 1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.1
The performance alarm threshold profile name.
Status: current Access: not-accessible
OBJECT-TYPE    
  DisplayString Size(1..32)  

zxAnCardEnvPerfVariable 1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.2
The object identifier of performance variables.
Status: current Access: not-accessible
OBJECT-TYPE    
  OBJECT IDENTIFIER  

zxAnCardEnvRiseAlmThresh 1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.3
The threshold for rising alarm.
Status: current Access: read-create
OBJECT-TYPE    
  HCPerfCurrentCount  

zxAnCardEnvClrRiseAlmThresh 1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.4
The threshold for rising alarm restore.
Status: current Access: read-create
OBJECT-TYPE    
  HCPerfCurrentCount  

zxAnCardEnvRiseWarnThresh 1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.5
The threshold for rising warning.
Status: current Access: read-create
OBJECT-TYPE    
  HCPerfCurrentCount  

zxAnCardEnvClrRiseWarnThresh 1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.6
The threshold for rising warning restore.
Status: current Access: read-create
OBJECT-TYPE    
  HCPerfCurrentCount  

zxAnCardEnvFallWarnThresh 1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.7
The threshold for falling warning.
Status: current Access: read-create
OBJECT-TYPE    
  HCPerfCurrentCount  

zxAnCardEnvClrFallWarnThresh 1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.8
The threshold for falling warning restore.
Status: current Access: read-create
OBJECT-TYPE    
  HCPerfCurrentCount  

zxAnCardEnvFallAlmThresh 1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.9
The threshold for falling alarm.
Status: current Access: read-create
OBJECT-TYPE    
  HCPerfCurrentCount  

zxAnCardEnvClrFallAlmThresh 1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.10
The threshold for falling alarm restore.
Status: current Access: read-create
OBJECT-TYPE    
  HCPerfCurrentCount  

zxAnCardEnvAlmPrfConfRowStatus 1.3.6.1.4.1.3902.1082.10.10.2.1.9.1.50
The status of this conceptual row. To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

zxAnCardEnvAlmProfileApplyTable 1.3.6.1.4.1.3902.1082.10.10.2.1.10
The performance alarm threshold profile application table of card temperature.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCardEnvAlmProfileApplyEntry

zxAnCardEnvAlmProfileApplyEntry 1.3.6.1.4.1.3902.1082.10.10.2.1.10.1
The performance alarm threshold profile application entry of card temperature.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCardEnvAlmProfileApplyEntry  

zxAnCardEnvAlmPrf 1.3.6.1.4.1.3902.1082.10.10.2.1.10.1.1
The performance alarm threshold profile.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..32)  

zxAnCardEnvAlmPrfApplyRowStatus 1.3.6.1.4.1.3902.1082.10.10.2.1.10.1.50
The status of this conceptual row. To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

zxAnCardEnvAlmProfileTable 1.3.6.1.4.1.3902.1082.10.10.2.1.11
The performance alarm threshold profile table of card temperature.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCardEnvAlmProfileEntry

zxAnCardEnvAlmProfileEntry 1.3.6.1.4.1.3902.1082.10.10.2.1.11.1
The performance alarm threshold profile entry of card temperature.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCardEnvAlmProfileEntry  

zxAnCardEnvAlmPrfRowStatus 1.3.6.1.4.1.3902.1082.10.10.2.1.11.1.50
The status of this conceptual row. To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

zxAnEnvOverheatProtectTable 1.3.6.1.4.1.3902.1082.10.10.2.1.13
Environment overheat protection table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnEnvOverheatProtectEntry

zxAnEnvOverheatProtectEntry 1.3.6.1.4.1.3902.1082.10.10.2.1.13.1
Environment overheat protection entry. To modify zxAnEnvOverheatProtectEnable from disabled to enabled, zxAnEnvOverheatProtectEnable is mandatory, zxAnEnvOverheatProtectDelay is optional. To modify zxAnEnvOverheatProtectEnable from enabled to disabled, only zxAnEnvOverheatProtectEnable is mandatory.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnEnvOverheatProtectEntry  

zxAnEnvOverheatProtectEnable 1.3.6.1.4.1.3902.1082.10.10.2.1.13.1.1
Enables or disables the environment overheat protection function.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

zxAnEnvOverheatProtectDelay 1.3.6.1.4.1.3902.1082.10.10.2.1.13.1.2
The delaying time between two steps. For example, when temperature is higher than the threshold, takes an action as the step 1, and delays the value of zxAnEnvOverheatProtectDelay, if the temperature is still higher than the threshold, takes an action as step 2.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..60  

zxAnEnvOverheatProtectFirstStep 0.1.2.1.3.6.1.4.1.3902.1082.10.10.2.1.13.1.3
The first step when the environment temperature exceeds zxAnEnvTempHighAlmThreshold.
Status: current Access: read-write
OBJECT-TYPE    
  ZxAnEnvShutdownServiceType  

zxAnEnvOverheatProtectSecondStep 3.1.3.6.1.4.1.3902.1082.10.10.2.1.13.1.4
The second step when the environment temperature still exceeds zxAnEnvTempHighAlmThreshold after first step has been done.
Status: current Access: read-write
OBJECT-TYPE    
  ZxAnEnvShutdownServiceType  

zxAnEnvCardOverheatProtectTable 1.3.6.1.4.1.3902.1082.10.10.2.1.14
Card overheat protection table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnEnvCardOverheatProtectEntry

zxAnEnvCardOverheatProtectEntry 1.3.6.1.4.1.3902.1082.10.10.2.1.14.1
Card overheat protection entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnEnvCardOverheatProtectEntry  

zxAnEnvCardCriticalTempProtectEn 1.3.6.1.4.1.3902.1082.10.10.2.1.14.1.1
Enables or disables the card critical temperature protection function. If it is enabled, the card will be stopped when the card temperature is higher than the card critical temperature.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

zxAnCardEnvHisMinPerfTable 1.3.6.1.4.1.3902.1082.10.10.2.1.15
The 5 minutes or 15 minutes interval environmental monitoring performance data table of card.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCardEnvHisMinPerfEntry

zxAnCardEnvHisMinPerfEntry 1.3.6.1.4.1.3902.1082.10.10.2.1.15.1
The 5 minutes or 15 minutes interval environmental monitoring performance data entry of card.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCardEnvHisMinPerfEntry  

zxAnCardEnvHMinIntervalNo 1.3.6.1.4.1.3902.1082.10.10.2.1.15.1.1
The performance data interval number. 1 means the the most recent previous interval; If the performance collection interval is 5 minutes, intervals 2..288 are optional. If the performance collection interval is 15 minutes, intervals 2..96 are optional.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..288  

zxAnCardEnvHMinIntervalValidData 1.3.6.1.4.1.3902.1082.10.10.2.1.15.1.2
Performance data validity.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

zxAnCardEnvHMinDateTime 1.3.6.1.4.1.3902.1082.10.10.2.1.15.1.3
The 5 minutes or 15 minutes interval performance data generation time.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

zxAnCardEnvHMinTemperature 1.3.6.1.4.1.3902.1082.10.10.2.1.15.1.4
The average temperature of card in the historical 5 minutes or 15 minutes. If the card does not have this attribute, it should be -1000.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCardEnvHMinVoltage 1.3.6.1.4.1.3902.1082.10.10.2.1.15.1.5
The average voltage of card in the historical 5 minutes or 15 minutes. If the card does not have this attribute, it should be 0.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCardEnvHMinPowerConsumption 1.3.6.1.4.1.3902.1082.10.10.2.1.15.1.6
The average power consumption of card in the historical 5 minutes or 15 minutes. If the card does not have this attribute, it should be 0.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnEnvMonInterfaceTable 1.3.6.1.4.1.3902.1082.10.10.2.2.5
This table includes the environment interface information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnEnvMonInterfaceEntry

zxAnEnvMonInterfaceEntry 1.3.6.1.4.1.3902.1082.10.10.2.2.5.1
The entry of zxAnEnvMonInterfaceTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnEnvMonInterfaceEntry  

zxAnEnvMonInterfaceUsage 1.3.6.1.4.1.3902.1082.10.10.2.2.5.1.1
The equipment type connected to the environment monitor interface.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER epm(1), fanTray(2), noUse(3), noSupport(4), etmWithTestSubcard(5), etmWithoutTestSubcard(6)  

zxAnEnvEpmConnectPort 1.3.6.1.4.1.3902.1082.10.10.2.2.5.1.2
The port no which epm connect
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER port0(1), port1(2), notconfigured(255)  

zxAnEnvBackplaneInterfaceUsage 1.3.6.1.4.1.3902.1082.10.10.2.2.5.1.3
The equipment type connected to the Backplane Interface. fan(1): the fan connect to the Backplane Interface; noUse(3): not used; noSupport(255):not support.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER fan(1), noUse(3), noSupport(255)  

zxAnEnvEmergencyPowerSaveEnable 1.3.6.1.4.1.3902.1082.10.10.2.3.1.1
Enables or disables the emergency power saving.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

zxAnEnvEmergencyPowerSaveDelay 1.3.6.1.4.1.3902.1082.10.10.2.3.1.2
If AC power failure lasts more than zxAnEnvEmergencyPowerSaveDelay, emergency power saving action will be taken.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1440  

zxAnEnvEmergencyPowerSaveRecover 1.3.6.1.4.1.3902.1082.10.10.2.3.1.3
If AC power recovered, after this delay, the emergency power save action will be cancelled.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1440  

zxAnEnvEmergencyPowerSaveSvcType 0.1.2.1.3.6.1.4.1.3902.1082.10.10.2.3.1.4
The service types will be shut down in emergency power saving action.
Status: current Access: read-write
OBJECT-TYPE    
  ZxAnEnvShutdownServiceType  

zxAnEnvPowerMode 1.3.6.1.4.1.3902.1082.10.10.2.3.1.5
The current power supply mode of the equipment, emergency power saving action is on the basis of the power mode zxAnEnvPowerMode. normal(1) means using AC power as power supply. battery(2) means using storage battery as power supply.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), battery(2)  

zxAnEnvEmergencyBatteryVoltage 1.3.6.1.4.1.3902.1082.10.10.2.3.1.6
The current voltage of the battery.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnEnvEmergencyBatteryThreshold 1.3.6.1.4.1.3902.1082.10.10.2.3.1.7
The threshold of the battery voltage. If the battery voltage is less than zxAnEnvEmergencyBatteryThreshold, the emergency power saving action will be taken.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 45000..53000  

zxAnEnvEnergySavingLevel 1.3.6.1.4.1.3902.1082.10.10.2.3.1.8
level1(1): Level 1 means that the energy saving module action will be taken automatically while the following conditions are detected: 1. There is no card plugged in the slot or the card plugged in the slot has been power off. 2. The actual card type is not same as the configured card type. level2(2): Level 2 means that the energy saving module action will be taken automatically while the following conditions are detected: 1. There is no card plugged in the slot or the card plugged in the slot has been power off. 2. The actual card type is not same as the configured card type. 3. There is no ONU which is configured on the card or on the port. level3(3): Level 3 means that the energy saving module action will be taken automatically while the following conditions are detected: 1. There is no card plugged in the slot or the card plugged in the slot has been power off. 2. The actual card type is not same as the configured card type. 3. There is no ONU which is configured on the card or on the port. 4. If all the uplink ports down, all the cards except the uplink card will be power off.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER level1(1), level2(2), level3(3)  

zxAnPowerSupplyCapabilityTable 1.3.6.1.4.1.3902.1082.10.10.2.3.10
This table includes power supply capability table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnPowerSupplyCapabilityEntry

zxAnPowerSupplyCapabilityEntry 1.3.6.1.4.1.3902.1082.10.10.2.3.10.1
The entry of zxAnPowerSupplyCapabilityTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnPowerSupplyCapabilityEntry  

zxAnPowerSupplyMaxPowerNum 1.3.6.1.4.1.3902.1082.10.10.2.3.10.1.1
The max number of power supply in the equipment.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnPowerSupplyTable 1.3.6.1.4.1.3902.1082.10.10.2.3.11
This table includes power supply table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnPowerSupplyEntry

zxAnPowerSupplyEntry 1.3.6.1.4.1.3902.1082.10.10.2.3.11.1
An entry in zxAnPowerSupplyTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnPowerSupplyEntry  

zxAnPowerSupplyOperStatus 1.3.6.1.4.1.3902.1082.10.10.2.3.11.1.1
The operational status of the power supply module.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inService(1), hwOffline(2), powerFaulty(3)  

zxAnPowerSupplyInVoltage 1.3.6.1.4.1.3902.1082.10.10.2.3.11.1.2
The actual input volts of the power supply module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnPowerSupplyInVoltageStatus 1.3.6.1.4.1.3902.1082.10.10.2.3.11.1.3
The volt status of the power supply. normal(1) -- The input power is normal. overVoltage(2) -- The input power is over voltage. underVoltage(3) -- The input power is under voltage. off(4)) -- No power input.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), overVoltage(2), underVoltage(3), off(4)  

zxAnPowerInVoltageUpperThresh 1.3.6.1.4.1.3902.1082.10.10.2.3.11.1.4
The upper threshold of input volts.The alarm should be generated when zxAnPowerSupplyInVoltage exceeds this threshold. If it is 0, no alarm reported to manager.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

zxAnPowerInVoltageLowerThresh 1.3.6.1.4.1.3902.1082.10.10.2.3.11.1.5
The lower threshold of input volts.The alarm should be generated when zxAnPowerSupplyInVoltage is lower than this threshold. If it is 0, no alarm reported to manager.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

zxAnPowerSupplyInCurrent 1.3.6.1.4.1.3902.1082.10.10.2.3.11.1.6
The actual current of the power supply module.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnPowerInCurrentThresh 1.3.6.1.4.1.3902.1082.10.10.2.3.11.1.7
The upper threshold of input current.The alarm should be generated when zxAnPowerSupplyInCurrent exceeds this threshold. If it is 0, no alarm reported to manager.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

zxAnEnvEnergySavingTable 1.3.6.1.4.1.3902.1082.10.10.2.3.12
The energy saving status table of the NE.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnEnvEnergySavingEntry

zxAnEnvEnergySavingEntry 1.3.6.1.4.1.3902.1082.10.10.2.3.12.1
An entry in zxAnEnvEnergySavingTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnEnvEnergySavingEntry  

zxAnEnvEnergySavingRack 1.3.6.1.4.1.3902.1082.10.10.2.3.12.1.1
The rack number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

zxAnEnvEnergySavingShelf 1.3.6.1.4.1.3902.1082.10.10.2.3.12.1.2
The shelf number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

zxAnEnvEnergySavingSlot 1.3.6.1.4.1.3902.1082.10.10.2.3.12.1.3
The slot number.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

zxAnEnvEnergySavingPort 1.3.6.1.4.1.3902.1082.10.10.2.3.12.1.4
The port number. If the card is power off, this object will be set to 255.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

zxAnEnvEnergySavingStatus 1.3.6.1.4.1.3902.1082.10.10.2.3.12.1.5
The energy saving status.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER cardEnergySaving(1), portShutDown(2)  

zxAnEnvEnergySavingReason 1.3.6.1.4.1.3902.1082.10.10.2.3.12.1.6
The energy saving reason.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER cardTypeMismatch(1), noOnuConfigured(2), allUplinkPortsDown(3), cardNotConfigured(4)  

zxAnEnvEnergySavingOccurringTime 1.3.6.1.4.1.3902.1082.10.10.2.3.12.1.7
The energy saving occurring time.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

zxAnEnvFanTrayTable 1.3.6.1.4.1.3902.1082.10.10.2.4.10
The Fan Tray Control table, with rack and shelf information.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnEnvFanTrayEntry

zxAnEnvFanTrayEntry 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1
An entry in the zxAnEnvFanTrayTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnEnvFanTrayEntry  

zxAnFanTrayAlarmBeepEnable 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.1
The control status of the fan alarm beep.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

zxAnFanTrayAutoSwitchByCardUp 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.2
Enable/disable fan auto switch with card installation. If it is enabled, the fan under the card should be switched to running status when the card is installed. Otherwise, the fan should be shutdown.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(2)  

zxAnFanTrayHardwareVersion 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.3
The hardware version of the fan tray
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

zxAnFanTraySoftwareVersion 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.4
The software version of the fan tray
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

zxAnFanTraySpeedCtrlMode 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.5
The speed control mode of the fan. When this value is fixSpeed,zxAnFanTrayAdminStatus, zxAnFanTrayConfSpeedLevel,zxAnEnvFanAdminStatus and zxAnEnvFanConfSpeedLevel can be configured.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER temperatureBasedAutoCtrl(1), fixSpeed(2)  

zxAnFanTrayLowSpeed 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.6
The speed value of the fan's low speed level. The values for ZXDSL9800,9210 are 1500,2400,2700,3000,3400,3700, 4000,4400. NOTE: Different equipment maybe has different default value.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

zxAnFanTrayStdSpeed 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.7
The speed value of the fan's standard speed level. The values for ZXDSL9800,9210 are 1500,2400,2700,3000,3400,3700, 4000,4400. NOTE: Different equipment maybe has different default value.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

zxAnFanTrayHighSpeed 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.8
The speed value of the fan's high speed level. The values for ZXDSL9800,9210 are 1500,2400,2700,3000,3400,3700, 4000,4400. NOTE: Different equipment maybe has different default value.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

zxAnFanTraySuperSpeed 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.9
The speed value of the fan's super speed level. The values for ZXDSL9800,9210 are 1500,2400,2700,3000,3400,3700, 4000,4400. NOTE: Different equipment maybe has different default value.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

zxAnFanTrayLowSpeedShiftTemp 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.10
The temperature to activate the fan tray to shift to the low speed level.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..55  

zxAnFanTrayStdSpeedShiftTemp 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.11
The temperature to activate the fan tray to shift to the standard speed level.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 5..60  

zxAnFanTrayHighSpeedShiftTemp 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.12
The temperature to activate the fan tray to shift to the high speed level.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10..65  

zxAnFanTraySuperSpeedShiftTemp 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.13
The temperature to activate the fan tray to shift to the super speed level.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 15..70  

zxAnFanTrayLowSpeedPercent 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.14
The percentage of speed of the low speed level.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 10..97  

zxAnFanTrayStdSpeedPercent 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.15
The percentage of speed of the standard speed level.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 11..98  

zxAnFanTrayHighSpeedPercent 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.16
The percentage of speed of the high speed level.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 12..99  

zxAnFanTraySuperSpeedPercent 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.17
The percentage of speed of the super speed level.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 13..100  

zxAnFanTrayAdminStatus 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.18
The administrative status of the fan tray. When zxAnFanTrayAdminStatus is configured, all the zxAnEnvFanAdminStatus values are consistent with zxAnFanTrayAdminStatus.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

zxAnFanTrayConfSpeedLevel 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.19
The configured speed level of the fan tray. When zxAnFanTrayConfSpeedLevel is configured, all the zxAnEnvFanConfSpeedLevel values are consistent with zxAnFanTrayConfSpeedLevel. This variable is valid if zxAnFanTrayAdminStatus is up.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER lowSpeed(1), standardSpeed(2), highSpeed(3), superSpeed(4)  

zxAnFanTrayPowerConsumption 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.20
Power consumption of the fan tray. Value 0 means not available.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnFanTraySn 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.21
The serial number of fan tray.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..12)  

zxAnFanTrayVoltage 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.22
Voltage of the fan tray. Value 0 means not available.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnFanTrayCurrent 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.23
Current of the fan tray. Value 0 means not available.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnFanTrayTemp 1.3.6.1.4.1.3902.1082.10.10.2.4.10.1.24
The temperature of the fan tray.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnEnvFanTable 1.3.6.1.4.1.3902.1082.10.10.2.4.11
This table includes speed information and operational status of the fan units.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnEnvFanEntry

zxAnEnvFanEntry 1.3.6.1.4.1.3902.1082.10.10.2.4.11.1
The entry of zxAnEnvFanTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnEnvFanEntry  

zxAnEnvFanIndex 1.3.6.1.4.1.3902.1082.10.10.2.4.11.1.1
The index of this fan unit. For 19-inch shelf, there are 3 fans in each fan tray. The fan index should be integer in [1,3]. For 21-inch shelf, there are 4 fans. The fan index should be integer in [1,4].
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32  

zxAnEnvFanConfSpeedLevel 1.3.6.1.4.1.3902.1082.10.10.2.4.11.1.2
The configured speed level of the fan unit singly.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER lowSpeed(1), standardSpeed(2), highSpeed(3), superSpeed(4)  

zxAnEnvFanActualSpeedLevel 1.3.6.1.4.1.3902.1082.10.10.2.4.11.1.3
The actual speed level of the fan unit.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER lowSpeed(1), standardSpeed(2), highSpeed(3), superSpeed(4), other(10)  

zxAnEnvFanAdminStatus 1.3.6.1.4.1.3902.1082.10.10.2.4.11.1.4
The administrative status of the fan unit singly.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER up(1), down(2)  

zxAnEnvFanOperStatus 1.3.6.1.4.1.3902.1082.10.10.2.4.11.1.5
The operational status of the fan unit.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), unknown(3)  

zxAnEnvFanOnlineStatus 1.3.6.1.4.1.3902.1082.10.10.2.4.11.1.6
The actual online status of the fan unit.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER online(1), offline(2), unknown(3)  

zxAnEnvFanActualSpeed 1.3.6.1.4.1.3902.1082.10.10.2.4.11.1.7
The actual speed of the fan unit. NOTE: If not supported, NMS should use the speed value of zxAnEnvFanActualSpeedLevel.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnEnvFanTrayResetRack 1.3.6.1.4.1.3902.1082.10.10.2.4.12.1
The rack number of the fan tray.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

zxAnEnvFanTrayResetShelfList 1.3.6.1.4.1.3902.1082.10.10.2.4.12.2
The shelf number list of the fan tray. They can be reset in batch, for example: 1,2,3. Setting this object to empty means all the fan trays connected with zxAnEnvFanTrayRack will be reset.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

zxAnEnvFanTrayResetAction 1.3.6.1.4.1.3902.1082.10.10.2.4.12.3
Reset the fan trays. To query this object, always return 1.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reset(1)  

zxAnEnvDeviceTable 1.3.6.1.4.1.3902.1082.10.10.2.5.2
The table of environment device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnEnvDeviceEntry

zxAnEnvDeviceEntry 1.3.6.1.4.1.3902.1082.10.10.2.5.2.1
The entry of the zxAnEnvDeviceTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnEnvDeviceEntry  

zxAnEnvDeviceId 1.3.6.1.4.1.3902.1082.10.10.2.5.2.1.1
The ID of this environment device. Value 1-50 is default value which can not be modified or deleted. If add a new device, the ID will be starting from 51.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..100  

zxAnEnvDeviceName 1.3.6.1.4.1.3902.1082.10.10.2.5.2.1.2
The name of the environment device.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(1..32)  

zxAnEnvDeviceRowStatus 1.3.6.1.4.1.3902.1082.10.10.2.5.2.1.50
The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4). To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

zxAnEnvDevMonSwitchTable 1.3.6.1.4.1.3902.1082.10.10.2.5.3
The table of the switch which monitors environment device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnEnvDevMonSwitchEntry

zxAnEnvDevMonSwitchEntry 1.3.6.1.4.1.3902.1082.10.10.2.5.3.1
The entry of the zxAnEnvDevMonSwitchTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnEnvDevMonSwitchEntry  

zxAnEnvDevMonSwitchId 1.3.6.1.4.1.3902.1082.10.10.2.5.3.1.1
The ID of the switch.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..8  

zxAnEnvDevMonSwitchDeviceId 1.3.6.1.4.1.3902.1082.10.10.2.5.3.1.2
The ID of the device which monitored by the switch. Value 0 means this switch does not monitor any device.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..100  

zxAnEnvDevMonSwitchTrapEnable 1.3.6.1.4.1.3902.1082.10.10.2.5.3.1.3
Enables or disables the environment device abnormal trap.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

zxAnEnvDevMonSwitchNormalStatus 1.3.6.1.4.1.3902.1082.10.10.2.5.3.1.4
The normal status of the environment device.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER lowLevel(1), highLevel(2)  

zxAnEnvDevMonSwitchCurrStatus 1.3.6.1.4.1.3902.1082.10.10.2.5.3.1.5
The current status of the environment device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER lowLevel(1), highLevel(2), unknown(255)  

zxAnEnvHighTempAlm 1.3.6.1.4.1.3902.1082.10.10.3.1.1
The environment temperature has exceeded high temperature threshold zxAnEnvTempHighAlmThreshold. The zxAnEnvTemp object identifies the current temperature.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvHighTempClr 1.3.6.1.4.1.3902.1082.10.10.3.1.2
The environment temperature has returned to normal operating temperature from zxAnEnvTempHighAlmThreshold. The zxAnEnvTemp object identifies the current temperature.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvTempSensorFailure 1.3.6.1.4.1.3902.1082.10.10.3.1.5
It indicates that the temperature sensor is in fault.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvCriticalTempAlm 1.3.6.1.4.1.3902.1082.10.10.3.1.6
The environment temperature has exceeded critical temperature threshold zxAnEnvTempCriticalAlmThreshold. The zxAnEnvTemp object identifies the current temperature.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvCriticalTempClr 1.3.6.1.4.1.3902.1082.10.10.3.1.7
The environment temperature has returned to normal operating temperature from zxAnEnvTempCriticalAlmThreshold. The zxAnEnvTemp object identifies the current temperature.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvLowTempAlm 1.3.6.1.4.1.3902.1082.10.10.3.1.8
The environment temperature is below low temperature threshold zxAnEnvTempLowAlmThreshold. The zxAnEnvTemp object identifies the current temperature.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvLowTempClr 1.3.6.1.4.1.3902.1082.10.10.3.1.9
The environment temperature has returned to normal operating temperature from zxAnEnvTempLowAlmThreshold. The zxAnEnvTemp object identifies the current temperature.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvCardShutdownAlm 1.3.6.1.4.1.3902.1082.10.10.3.1.30
A zxAnEnvCardShutdownAlm trap is sent when the card has been shut down because agent has detected that the temperature is too high or the AC power is failure and the battery voltage is lower than zxAnEnvEmergencyBatteryThreshold. zxAnEnvCardShutdownReason indicates the real reason. When zxAnEnvCardShutdownReason is envHighTemperature ( 1 ), it means the environment temperature is too high, zxAnEnvTemp is the value of current environment temperature, zxAnCardTemp is invalid and should be zero. zxAnEnvEmergencyBatteryVoltage and zxAnEnvEmergencyBatteryThreshold are invalid and should be zero. When zxAnEnvCardShutdownReason is cardHighTemperature ( 2 ), it means the card temperature is too high, zxAnCardTemp is the value of current card temperature, zxAnEnvTemp is invalid and should be zero. zxAnEnvEmergencyBatteryVoltage and zxAnEnvEmergencyBatteryThreshold are invalid and should be zero. When zxAnEnvCardShutdownReason is chipHighTemperature ( 3 ), it means the temperature of the chip on the card is too high, zxAnCardTemp and zxAnEnvTemp are invalid and should be zero. zxAnEnvEmergencyBatteryVoltage and zxAnEnvEmergencyBatteryThreshold are invalid and should be zero. When zxAnEnvCardShutdownReason is emergencyPowerSaving ( 4 ), it means the AC power is failure, the emergency power saving action has been taken, zxAnCardTemp and zxAnEnvTemp are invalid and should be zero. zxAnEnvEmergencyBatteryVoltage is the value of the current battery voltage, zxAnEnvEmergencyBatteryThreshold is the threshold of the battery voltage.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvCardShutdownClr 1.3.6.1.4.1.3902.1082.10.10.3.1.31
A zxAnEnvCardShutdownClr trap is sent when the card temperature becomes normal, or the environment temperature becomes normal, or the chip temperature becomes normal, or the battery voltage is higher than zxAnEnvEmergencyBatteryThreshold or AC power becomes normal.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvTemperatureAbnormalAlm 1.3.6.1.4.1.3902.1082.10.10.3.1.32
In temperature control mode, a zxAnEnvTemperatureAbnormalAlm trap is sent when the environment temperature can't be read.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvTemperatureAbnormalClr 1.3.6.1.4.1.3902.1082.10.10.3.1.33
A zxAnEnvTemperatureAbnormalClr trap is sent when the zxAnEnvTemperatureAbnormalAlm is cleared.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvNearCriticalTempAlm 1.3.6.1.4.1.3902.1082.10.10.3.1.34
A zxAnEnvNearCriticalTempAlm trap is sent when the environment temperature is close to the environment critical temperature alarm threshold.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvNearCriticalTempClr 1.3.6.1.4.1.3902.1082.10.10.3.1.35
A zxAnEnvNearCriticalTempClr trap is sent when the zxAnEnvNearCriticalTempAlm is cleared.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvCardNearCriticalTempAlm 1.3.6.1.4.1.3902.1082.10.10.3.1.36
A zxAnEnvCardNearCriticalTempAlm trap is sent when the card temperature is close to the card critical temperature alarm threshold.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvCardNearCriticalTempClr 1.3.6.1.4.1.3902.1082.10.10.3.1.37
A zxAnEnvCardNearCriticalTempClr trap is sent when the zxAnEnvCardNearCriticalTempAlm is cleared.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvOptNearCriticalTempAlm 1.3.6.1.4.1.3902.1082.10.10.3.1.38
A zxAnEnvOptNearCriticalTempAlm trap is sent when the optical module temperature is close to the optical module critical temperature alarm threshold.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvOptNearCriticalTempClr 1.3.6.1.4.1.3902.1082.10.10.3.1.39
A zxAnEnvOptNearCriticalTempClr trap is sent when the zxAnEnvOptNearCriticalTempAlm is cleared.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvHeatRadiationAbnormalAlm 1.3.6.1.4.1.3902.1082.10.10.3.1.40
A zxAnEnvHeatRadiationAbnormalAlm trap is sent when the temperature difference between the card and the environment exceeds the zxAnCardHeatRadiationAlmThresh.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvHeatRadiationAbnormalClr 1.3.6.1.4.1.3902.1082.10.10.3.1.41
A zxAnEnvHeatRadiationAbnormalClr trap is sent when the zxAnEnvHeatRadiationAbnormalAlm is cleared.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvMonitorInterfaceLinkDown 1.3.6.1.4.1.3902.1082.10.10.3.2.1
It indicates that the agent has detected that the link at the environment monitoring interface has been down.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvMonitorInterfaceLinkUp 1.3.6.1.4.1.3902.1082.10.10.3.2.2
It indicates that the agent has detected that the link at the environment monitoring interface has been up.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvPowerSupplyModuleDown 1.3.6.1.4.1.3902.1082.10.10.3.3.1
It indicates that the power supply module is down.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvPowerSupplyModuleUp 1.3.6.1.4.1.3902.1082.10.10.3.3.2
It indicates that the power supply module is up.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvPowerOverVoltageAlm 1.3.6.1.4.1.3902.1082.10.10.3.3.3
It indicates that the input voltage of power supply is over-voltage.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvPowerOverVoltageClr 1.3.6.1.4.1.3902.1082.10.10.3.3.4
It indicates that the over-voltage fault is cleared.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvPowerUnderVoltageAlm 1.3.6.1.4.1.3902.1082.10.10.3.3.5
It indicates that the input voltage of power supply is under-voltage.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvPowerUnderVoltageClr 1.3.6.1.4.1.3902.1082.10.10.3.3.6
It indicates that the under-voltage fault is cleared.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvPowerOff 1.3.6.1.4.1.3902.1082.10.10.3.3.7
It indicates that the power supply is off.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvPowerOn 1.3.6.1.4.1.3902.1082.10.10.3.3.8
It indicates that the power supply off fault is cleared.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvEmergencyPowerSaveAlm 1.3.6.1.4.1.3902.1082.10.10.3.3.9
The current power supply switches to storage battery, the emergency power saving action has been taken.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvEmergencyPowerSaveClr 1.3.6.1.4.1.3902.1082.10.10.3.3.10
The current power supply switches to normal AC power.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvACPowerDownAlm 1.3.6.1.4.1.3902.1082.10.10.3.3.11
A zxAnEnvACPowerDownAlm trap is sent when the agent detects no AC power input.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvACPowerDownClr 1.3.6.1.4.1.3902.1082.10.10.3.3.12
A zxAnEnvACPowerDownClr trap is sent when the agent detects AC power input.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvNoBatteryAlm 1.3.6.1.4.1.3902.1082.10.10.3.3.13
A zxAnEnvNoBatteryAlm trap is sent when no battery found by the agent.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvNoBatteryClr 1.3.6.1.4.1.3902.1082.10.10.3.3.14
A zxAnEnvNoBatteryClr trap is sent when the battery has been found by the agent.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvBatteryUnderVoltageAlm 1.3.6.1.4.1.3902.1082.10.10.3.3.15
A zxAnEnvBatteryUnderVoltageAlm trap is sent when the battery voltage is under-voltage.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvBatteryUnderVoltageClr 1.3.6.1.4.1.3902.1082.10.10.3.3.16
A zxAnEnvBatteryUnderVoltageClr trap is sent when the battery voltage becomes normal.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvFanLinkDown 1.3.6.1.4.1.3902.1082.10.10.3.4.1
It indicates that the agent has detected that fan is offline.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvFanLinkUp 1.3.6.1.4.1.3902.1082.10.10.3.4.2
It indicates that the agent has detected that fan is online.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvFanTrayLinkDown 1.3.6.1.4.1.3902.1082.10.10.3.4.3
It indicates that the agent has detected that the link at the fan card interface has been down.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvFanTrayLinkUp 1.3.6.1.4.1.3902.1082.10.10.3.4.4
It indicates that the agent has detected that the link at the fan card interface has been up.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvFanFailureAlm 1.3.6.1.4.1.3902.1082.10.10.3.4.5
It indicates that the fan is in fault.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvFanFailureClr 1.3.6.1.4.1.3902.1082.10.10.3.4.6
It indicates that the fan's fault is cleared.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvDeviceAbnormalAlm 1.3.6.1.4.1.3902.1082.10.10.3.5.1
A zxAnEnvDeviceAbnormalAlm trap is sent when the current status of environment device is inconsistent with normal status.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvDeviceAbnormalClr 1.3.6.1.4.1.3902.1082.10.10.3.5.2
A zxAnEnvDeviceAbnormalClr trap is sent when current status of environment device is consistent with normal status.
Status: current Access: read-only
NOTIFICATION-TYPE    

zxAnEnvMonConformance 1.3.6.1.4.1.3902.1082.10.10.4
OBJECT IDENTIFIER    

zxAnEnvMonCompliances 1.3.6.1.4.1.3902.1082.10.10.4.1
OBJECT IDENTIFIER    

zxAnEnvMonGroups 1.3.6.1.4.1.3902.1082.10.10.4.2
OBJECT IDENTIFIER    

zxAnEnvMonCompliance 1.3.6.1.4.1.3902.1082.10.10.4.1.1
The compliance statement for SNMP entities which implement the ZTE-AN-ENVMON-MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

zxAnEnvMonCapabilitiesGroup 1.3.6.1.4.1.3902.1082.10.10.4.2.1
The collection of objects which are used to represent environment management capabilities of this equipment. The bit value 1 means the function represented by this bit is supported by this equipment.
Status: current Access: read-only
OBJECT-GROUP    

zxAnEnvTempGroup 1.3.6.1.4.1.3902.1082.10.10.4.2.2
The collection of objects which are used to represent the temperature information of this equipment/card and to set the temperature alarm threshold of the environment/card.
Status: current Access: read-only
OBJECT-GROUP    

zxAnEnvCardTempGroup 1.3.6.1.4.1.3902.1082.10.10.4.2.3
The collection of objects which are used to represent temperature performance of the card environment.
Status: current Access: read-only
OBJECT-GROUP    

zxAnEnvInterfaceGroup 1.3.6.1.4.1.3902.1082.10.10.4.2.4
The collection of objects which are used to represent the interface connection of the equipment.
Status: current Access: read-only
OBJECT-GROUP    

zxAnEnvPowerSupplyGroup 1.3.6.1.4.1.3902.1082.10.10.4.2.5
The collection of objects which are used to provide power management functions, include power count and the voltage status of the power supply.
Status: current Access: read-only
OBJECT-GROUP    

zxAnEnvFanTrayTableGroup 1.3.6.1.4.1.3902.1082.10.10.4.2.6
The collection of objects which are used to provide fan management functions, include setting the speed control mode and the percentage of speed of the different speed level of the fan.
Status: current Access: read-only
OBJECT-GROUP    

zxAnEnvFanTableGroup 1.3.6.1.4.1.3902.1082.10.10.4.2.7
The collection of objects which are used to provide the speed information and operational status of the fan.
Status: current Access: read-only
OBJECT-GROUP    

zxAnEnvMonNotificationsGroup 1.3.6.1.4.1.3902.1082.10.10.4.2.8
The notifications which indicate specific changes, include temperature, fan status, power status and gpon card status.
Status: current Access: read-only
OBJECT-GROUP    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor