ZTE-AN-CFM2-MIB

File: ZTE-AN-CFM2-MIB.mib (124267 bytes)

Imported modules

IEEE8021-CFM-MIB IF-MIB SNMPv2-SMI
SNMPv2-TC ZTE-AN-TC-MIB ZTE-AN-SMI

Imported symbols

Dot1agCfmMaintDomainNameType Dot1agCfmMaintDomainName Dot1agCfmMDLevel
Dot1agCfmMhfCreation Dot1agCfmCcmInterval Dot1agCfmIdPermission
Dot1afCfmIndexIntegerNextFree Dot1agCfmMaintAssocName Dot1agCfmLowestAlarmPri
Dot1agCfmHighestDefectPri Dot1agCfmMpDirection Dot1agCfmFngState
Dot1agCfmRelayActionFieldValue Dot1agCfmIngressActionFieldValue Dot1agCfmEgressActionFieldValue
Dot1agCfmMepDefects Dot1agCfmMaintAssocNameType Dot1agCfmMepIdOrZero
Dot1agCfmMepId InterfaceIndex Integer32
Unsigned32 Counter32 Counter64
OBJECT-TYPE MODULE-IDENTITY MacAddress
RowStatus DateAndTime VlanId
ZxAnSubIfIndex zxAnOam

Defined Types

ZxAnCfm2MdEntry  
SEQUENCE    
  zxAnCfm2MdIndex Unsigned32
  zxAnCfm2MdFormat Dot1agCfmMaintDomainNameType
  zxAnCfm2MdName Dot1agCfmMaintDomainName
  zxAnCfm2MdMdLevel Dot1agCfmMDLevel
  zxAnCfm2MdMhfCreation Dot1agCfmMhfCreation
  zxAnCfm2MdMhfIdPermission Dot1agCfmIdPermission
  zxAnCfm2MdMaNextIndex Dot1afCfmIndexIntegerNextFree
  zxAnCfm2MdRowStatus RowStatus

ZxAnCfm2MaEntry  
SEQUENCE    
  zxAnCfm2MaIndex Integer32
  zxAnCfm2MaFormat Dot1agCfmMaintAssocNameType
  zxAnCfm2MaName Dot1agCfmMaintAssocName
  zxAnCfm2MaCcmInterval Dot1agCfmCcmInterval
  zxAnCfm2MaPrimarySVid VlanId
  zxAnCfm2MaPrimaryCVid Integer32
  zxAnCfm2MaCcmTimeoutCoefficient Integer32
  zxAnCfm2MaRowStatus RowStatus

ZxAnCfm2LocalMepEntry  
SEQUENCE    
  zxAnCfm2MpIdentifier Dot1agCfmMepId
  zxAnCfm2LMepIfIndex InterfaceIndex
  zxAnCfm2LMepSubIfIndex ZxAnSubIfIndex
  zxAnCfm2LMepDirection Dot1agCfmMpDirection
  zxAnCfm2LMepAdminStatus INTEGER
  zxAnCfm2LMepLowestPriDefect Dot1agCfmLowestAlarmPri
  zxAnCfm2LMepCcmSendEnable INTEGER
  zxAnCfm2LMepCcmLtmPriority Integer32
  zxAnCfm2LMepCcmDestMacType INTEGER
  zxAnCfm2LMepCcmRdiSendEnable INTEGER
  zxAnCfm2LMepCcmRdiTrustEnable INTEGER
  zxAnCfm2LMepCciSentCcms Counter32
  zxAnCfm2LMepFngState Dot1agCfmFngState
  zxAnCfm2LMepHighestPriDefect INTEGER
  zxAnCfm2LMepDefects Dot1agCfmMepDefects
  zxAnCfm2LMepAisEnable INTEGER
  zxAnCfm2LMepAisLckInterval INTEGER
  zxAnCfm2LMepAisPriority Integer32
  zxAnCfm2LMepAisCondition INTEGER
  zxAnCfm2LMepClientMegLevel OCTET STRING
  zxAnCfm2LMepMacAddress MacAddress
  zxAnCfm2LMepDmTwoWayFdMsrR1Max Integer32
  zxAnCfm2LMepDmTwoWayFdMsrR2Max Integer32
  zxAnCfm2LMepDmTwoWayFdMsrR3Max Integer32
  zxAnCfm2LMepDmOneWayIfdvMsrR1Max Integer32
  zxAnCfm2LMepDmOneWayIfdvMsrR2Max Integer32
  zxAnCfm2LMepDmOneWayIfdvMsrR3Max Integer32
  zxAnCfm2LMepRowStatus RowStatus

ZxAnCfm2RemoteMepEntry  
SEQUENCE    
  zxAnCfm2RMepMacAddress MacAddress
  zxAnCfm2RMepAdminStatus INTEGER
  zxAnCfm2RMepRowStatus RowStatus

ZxAnCfm2MipEntry  
SEQUENCE    
  zxAnCfm2MipIfIndex InterfaceIndex
  zxAnCfm2MipSubIfIndex ZxAnSubIfIndex
  zxAnCfm2MipRowStatus RowStatus

ZxAnCfm2MepLoopBackOperEntry  
SEQUENCE    
  zxAnCfm2MepTransLbmEnable INTEGER
  zxAnCfm2MepTransLbmMessages Integer32
  zxAnCfm2MepLbmDestMacType INTEGER
  zxAnCfm2MepLbAppType INTEGER
  zxAnCfm2MepTransLbmDestMacAddr MacAddress
  zxAnCfm2MepTransLbmDestMepId Dot1agCfmMepIdOrZero
  zxAnCfm2MepTransLbmDestMepType INTEGER
  zxAnCfm2MepTransLbmDataTlvLength Integer32
  zxAnCfm2MepTransLbmVlanPriority Integer32
  zxAnCfm2MepTransLbmTimeout Integer32
  zxAnCfm2MepTransLbmResultOk INTEGER
  zxAnCfm2MepTransLbmSeqNumber Unsigned32
  zxAnCfm2MepNextLbmTransId Unsigned32
  zxAnCfm2MepLbrInInOrder Counter32
  zxAnCfm2MepLbrInOutOfOrder Counter32
  zxAnCfm2MepLbrBadMsdu Counter32
  zxAnCfm2MepLbrOut Counter32
  zxAnCfm2MepLbMaxLatency Integer32
  zxAnCfm2MepLbMinLatency Integer32
  zxAnCfm2MepLbAvgLatency Integer32

ZxAnCfm2MepMultiLbrEntry  
SEQUENCE    
  zxAnCfm2MepMultiLbrDestMepMac MacAddress
  zxAnCfm2MepMultiLbrMepLbrIn Counter32
  zxAnCfm2MepMultiLbMaxLatency Integer32
  zxAnCfm2MepMultiLbMinLatency Integer32
  zxAnCfm2MepMultiLbAvgLatency Integer32

ZxAnCfm2MepLinkTraceOperEntry  
SEQUENCE    
  zxAnCfm2MepTransLtmEnable INTEGER
  zxAnCfm2MepTransLtmFlags BITS
  zxAnCfm2MepTransLtmDestMacAddr MacAddress
  zxAnCfm2MepTransLtmTargetMepId Dot1agCfmMepIdOrZero
  zxAnCfm2MepTransLtmTargetMepType INTEGER
  zxAnCfm2MepTransLtmTtl Integer32
  zxAnCfm2MepTransLtmTimeout Integer32
  zxAnCfm2MepTransLtmResultOk INTEGER
  zxAnCfm2MepTransLtmSeqNumber Unsigned32
  zxAnCfm2MepLtmNextSeqNumber Unsigned32
  zxAnCfm2MepUnexpLtrIn Counter32

ZxAnCfm2MepLinkTraceReplyEntry  
SEQUENCE    
  zxAnCfm2MepLtrSeqNumber Unsigned32
  zxAnCfm2MepLtrReceiveOrder Unsigned32
  zxAnCfm2MepLtrTtl Integer32
  zxAnCfm2MepLtrForwarded INTEGER
  zxAnCfm2MepLtrTerminalMep INTEGER
  zxAnCfm2MepLtrLastEgressId OCTET STRING
  zxAnCfm2MepLtrNextEgressId OCTET STRING
  zxAnCfm2MepLtrRelay Dot1agCfmRelayActionFieldValue
  zxAnCfm2MepLtrIngress Dot1agCfmIngressActionFieldValue
  zxAnCfm2MepLtrIngressMac MacAddress
  zxAnCfm2MepLtrEgress Dot1agCfmEgressActionFieldValue
  zxAnCfm2MepLtrEgressMac MacAddress

ZxAnCfm2MepDmOperEntry  
SEQUENCE    
  zxAnCfmMepDmTestId Integer32
  zxAnCfm2MepDmEnable INTEGER
  zxAnCfm2MepDmTargetMepId Dot1agCfmMepIdOrZero
  zxAnCfm2MepDmFrameSize INTEGER
  zxAnCfm2MepDmAppType INTEGER
  zxAnCfm2MepDmInterval INTEGER
  zxAnCfm2MepDmDuration Integer32
  zxAnCfm2MepDmPriority Integer32
  zxAnCfm2MepDmOperType INTEGER
  zxAnCfm2MepDmResultOk INTEGER

ZxAnCfm2MepDmRltEntry  
SEQUENCE    
  zxAnCfm2DmRemoteMepId Dot1agCfmMepId
  zxAnCfm2MepDmStartTime DateAndTime
  zxAnCfm2MepDmEndTime DateAndTime
  zxAnCfm2MepDmElapsedTime Integer32
  zxAnCfm2MepDmSentPkts Counter32
  zxAnCfm2MepDmReceivedPkts Counter32
  zxAnCfm2MepDmTwoWayFdMsr Counter32
  zxAnCfm2MepDmTwoWayFdMsrAvg Integer32
  zxAnCfm2MepDmTwoWayFdMsrMin Integer32
  zxAnCfm2MepDmTwoWayFdMsrMax Integer32
  zxAnCfm2MepDmOneWayFwdIfdvMsr Counter32
  zxAnCfm2MepDmOneWayFwdIfdvMsrAvg Integer32
  zxAnCfm2MepDmOneWayFwdIfdvMsrMax Integer32
  zxAnCfm2MepDmOneWayFwdIfdvMsrMin Integer32
  zxAnCfm2MepDmOneWayBwdIfdvMsr Counter32
  zxAnCfm2MepDmOneWayBwdIfdvMsrAvg Integer32
  zxAnCfm2MepDmOneWayBwdIfdvMsrMax Integer32
  zxAnCfm2MepDmOneWayBwdIfdvMsrMin Integer32
  zxAnCfm2MepDmTwoWayFdMsrR1C Integer32
  zxAnCfm2MepDmTwoWayFdMsrR2C Integer32
  zxAnCfm2MepDmTwoWayFdMsrR3C Integer32
  zxAnCfm2MepDmTwoWayFdMsrR4C Integer32
  zxAnCfm2MepDmOneWayFwdIfdvMsrR1C Integer32
  zxAnCfm2MepDmOneWayFwdIfdvMsrR2C Integer32
  zxAnCfm2MepDmOneWayFwdIfdvMsrR3C Integer32
  zxAnCfm2MepDmOneWayFwdIfdvMsrR4C Integer32
  zxAnCfm2MepDmOneWayBwdIfdvMsrR1C Integer32
  zxAnCfm2MepDmOneWayBwdIfdvMsrR2C Integer32
  zxAnCfm2MepDmOneWayBwdIfdvMsrR3C Integer32
  zxAnCfm2MepDmOneWayBwdIfdvMsrR4C Integer32

ZxAnCfm2MepLmOperEntry  
SEQUENCE    
  zxAnCfm2MepLmTestId Integer32
  zxAnCfm2MepLmEnable INTEGER
  zxAnCfm2MepLmTargetMepId Dot1agCfmMepIdOrZero
  zxAnCfm2MepLmAppType INTEGER
  zxAnCfm2MepLmInterval INTEGER
  zxAnCfm2MepLmDuration Integer32
  zxAnCfm2MepLmPriority Integer32
  zxAnCfm2MepLmOperType INTEGER
  zxAnCfm2MepLmResultOk INTEGER

ZxAnCfm2MepLmRltEntry  
SEQUENCE    
  zxAnCfm2LmRemoteMepId Dot1agCfmMepId
  zxAnCfm2MepLmStartTime DateAndTime
  zxAnCfm2MepLmEndTime DateAndTime
  zxAnCfm2MepLmElapsedTime Integer32
  zxAnCfm2MepLmSentPkts Counter32
  zxAnCfm2MepLmReceivedPkts Counter32
  zxAnCfm2MepLmFwdSentPkts Counter64
  zxAnCfm2MepLmFwdReceivedPkts Counter64
  zxAnCfm2MepLmFwdLossRatio Integer32
  zxAnCfm2MepLmBwdSentPkts Counter64
  zxAnCfm2MepLmBwdReceivedPkts Counter64
  zxAnCfm2MepLmBwdLossRatio Integer32

ZxAnCfm2MepSlmOperEntry  
SEQUENCE    
  zxAnCfm2MepSlmTestId Integer32
  zxAnCfm2MepSlmEnable INTEGER
  zxAnCfm2MepSlmTargetMepId Dot1agCfmMepIdOrZero
  zxAnCfm2MepSlmAppType INTEGER
  zxAnCfm2MepSlmInterval INTEGER
  zxAnCfm2MepSlmDuration Integer32
  zxAnCfm2MepSlmPriority Integer32
  zxAnCfm2MepSlmFrameSize INTEGER
  zxAnCfm2MepSlmOperType INTEGER
  zxAnCfm2MepSlmResultOk INTEGER

ZxAnCfm2MepSlmRltEntry  
SEQUENCE    
  zxAnCfm2SlmRemoteMepId Dot1agCfmMepId
  zxAnCfm2MepSlmStartTime DateAndTime
  zxAnCfm2MepSlmEndTime DateAndTime
  zxAnCfm2MepSlmElapsedTime Integer32
  zxAnCfm2MepSlmSentPkts Counter32
  zxAnCfm2MepSlmReceivedPkts Counter32
  zxAnCfm2MepSlmFwdSentPkts Counter32
  zxAnCfm2MepSlmFwdReceivedPkts Counter32
  zxAnCfm2MepSlmFwdLossPkts Integer32
  zxAnCfm2MepSlmFwdLossRatio Integer32
  zxAnCfm2MepSlmBwdSentPkts Counter32
  zxAnCfm2MepSlmBwdReceivedPkts Counter32
  zxAnCfm2MepSlmBwdLossPkts Integer32
  zxAnCfm2MepSlmBwdLossRatio Integer32

ZxAnCfm2MepStatsEntry  
SEQUENCE    
  zxAnCfm2MepStatsRxPkts Counter64
  zxAnCfm2MepStatsTxPkts Counter64
  zxAnCfm2MepStatsRxSequenceErrors Counter64
  zxAnCfm2MepStatsRxSrcMacErrors Counter64
  zxAnCfm2MepStatsRxCorrectPkts Counter64
  zxAnCfm2MepStatsRxIllegalPkts Counter64
  zxAnCfm2MepStatsReset INTEGER

Defined Values

zxAnCfm2Mib 1.3.6.1.4.1.3902.1082.80.45
This MIB defines managed objects of the Connectivity Fault Management module for managing Y.1731.
MODULE-IDENTITY    

zxAnCfm2GlobalObjects 1.3.6.1.4.1.3902.1082.80.45.1
OBJECT IDENTIFIER    

zxAnCfm2Objects 1.3.6.1.4.1.3902.1082.80.45.2
OBJECT IDENTIFIER    

zxAnCfm2MdObjects 1.3.6.1.4.1.3902.1082.80.45.2.1
OBJECT IDENTIFIER    

zxAnCfm2MaObjects 1.3.6.1.4.1.3902.1082.80.45.2.2
OBJECT IDENTIFIER    

zxAnCfm2MpObjects 1.3.6.1.4.1.3902.1082.80.45.2.3
OBJECT IDENTIFIER    

zxAnCfm2LocalMepObjects 1.3.6.1.4.1.3902.1082.80.45.2.3.2
OBJECT IDENTIFIER    

zxAnCfm2RemoteMepObjects 1.3.6.1.4.1.3902.1082.80.45.2.3.3
OBJECT IDENTIFIER    

zxAnCfm2MipObjects 1.3.6.1.4.1.3902.1082.80.45.2.3.4
OBJECT IDENTIFIER    

zxAnCfm2ConnectMeasureObjects 1.3.6.1.4.1.3902.1082.80.45.2.3.21
OBJECT IDENTIFIER    

zxAnCfm2PerfMeasureObjects 1.3.6.1.4.1.3902.1082.80.45.2.3.22
OBJECT IDENTIFIER    

zxAnCfm2StatisticsObjects 1.3.6.1.4.1.3902.1082.80.45.2.3.23
OBJECT IDENTIFIER    

zxAnCfm2Capabilities 1.3.6.1.4.1.3902.1082.80.45.1.1
The management capabilities of CFM. The bit value 1 means the function represented by this bit is supported by this equipment. bit 0: value 1 means supporting zxAnCfm2LMepDmTwoWayFdMsrR1Max, zxAnCfm2LMepDmTwoWayFdMsrR2Max, zxAnCfm2LMepDmTwoWayFdMsrR3Max, zxAnCfm2LMepDmOneWayIfdvMsrR1Max, zxAnCfm2LMepDmOneWayIfdvMsrR2Max and zxAnCfm2LMepDmOneWayIfdvMsrR3Max in zxAnCfm2LocalMepTable.
Status: current Access: read-only
OBJECT-TYPE    
  BITS supportLocalMepDmResultBin(0)  

zxAnCfm2Enable 1.3.6.1.4.1.3902.1082.80.45.1.2
Enable/disable the CFM functions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

zxAnCfm2TlvIgnoreEnable 1.3.6.1.4.1.3902.1082.80.45.1.3
Enable/disable TLV ignoring. enabled(1): The TLV of the packet is ignored from the peer side. disabled(2): The TLV of the packet is not ignored from the peer side.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

zxAnCfm2MdGlobalObjects 1.3.6.1.4.1.3902.1082.80.45.2.1.1
OBJECT IDENTIFIER    

zxAnCfm2MdTableNextIndex 1.3.6.1.4.1.3902.1082.80.45.2.1.1.1
An unused value for zxAnCfm2MdIndex in the zxAnCfm2MdTable, or a zero to indicate that none exist.
Status: current Access: read-only
OBJECT-TYPE    
  Dot1afCfmIndexIntegerNextFree  

zxAnCfm2MdTable 1.3.6.1.4.1.3902.1082.80.45.2.1.2
The Maintenance Domain table. Each row in the table represents a different Maintenance Domain. A Maintenance Domain is described in 802.1ag (3.22) as the network or the part of the network for which faults in connectivity are to be managed. The boundary of a Maintenance Domain is defined by a set of DSAPs, each of which can become a point of connectivity to a service instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCfm2MdEntry

zxAnCfm2MdEntry 1.3.6.1.4.1.3902.1082.80.45.2.1.2.1
The Maintenance Domain table entry. This entry is not lost upon reboot. It is backed up by stable storage.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCfm2MdEntry  

zxAnCfm2MdIndex 1.3.6.1.4.1.3902.1082.80.45.2.1.2.1.1
The index to the Maintenance Domain table. zxAnCfm2MdTableNextIndex needs to be inspected to find an available index for row-creation. Referential integrity is required, i.e., the index needs to be persistent upon a reboot or restart of a device. The index can never be reused for other Maintenance Domain. The index value SHOULD keep increasing up to the time that they wrap around. This is to facilitate access control based on OID.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

zxAnCfm2MdFormat 1.3.6.1.4.1.3902.1082.80.45.2.1.2.1.2
The type (and thereby format) of the Maintenance Domain Name.
Status: current Access: read-create
OBJECT-TYPE    
  Dot1agCfmMaintDomainNameType  

zxAnCfm2MdName 1.3.6.1.4.1.3902.1082.80.45.2.1.2.1.3
The Maintenance Domain name. The type/format of this object is determined by the value of the zxAnCfm2MdFormat object. Each Maintenance Domain has unique name amongst all those used or available to a service provider or operator. It facilitates easy identification of administrative responsibility for each Maintenance Domain.
Status: current Access: read-create
OBJECT-TYPE    
  Dot1agCfmMaintDomainName  

zxAnCfm2MdMdLevel 1.3.6.1.4.1.3902.1082.80.45.2.1.2.1.4
The Maintenance Domain Level.
Status: current Access: read-create
OBJECT-TYPE    
  Dot1agCfmMDLevel  

zxAnCfm2MdMhfCreation 1.3.6.1.4.1.3902.1082.80.45.2.1.2.1.5
Enumerated value indicating whether the management entity can create MHFs (MIP Half Function) for this Maintenance Domain. Since, in this variable, there is no encompassing Maintenance Domain, the value defMHFdefer is not allowed.
Status: current Access: read-create
OBJECT-TYPE    
  Dot1agCfmMhfCreation defMHFnone(1), defMHFdefault(2), defMHFexplicit(3)  

zxAnCfm2MdMhfIdPermission 1.3.6.1.4.1.3902.1082.80.45.2.1.2.1.6
Enumerated value indicating what, if anything, is to be included in the Sender ID TLV (21.5.3) transmitted by MPs configured in this Maintenance Domain. Since, in this variable, there is no encompassing Maintenance Domain, the value sendIdDefer is not allowed.
Status: current Access: read-create
OBJECT-TYPE    
  Dot1agCfmIdPermission sendIdNone(1), sendIdChassis(2), sendIdManage(3), sendIdChassisManage(4)  

zxAnCfm2MdMaNextIndex 1.3.6.1.4.1.3902.1082.80.45.2.1.2.1.7
Value to be used as the index of the MA table entries, to the zxAnCfm2MaTable for this Maintenance Domain when the management entity wants to create a new row in those tables.
Status: current Access: read-only
OBJECT-TYPE    
  Dot1afCfmIndexIntegerNextFree  

zxAnCfm2MdRowStatus 1.3.6.1.4.1.3902.1082.80.45.2.1.2.1.50
The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnCfm2MdEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

zxAnCfm2MaTable 1.3.6.1.4.1.3902.1082.80.45.2.2.2
The Maintenance Association table. Each row in the table represents an MA. An MA is a set of MEPs, each configured with a single service instance. Creation of a Service Instance establishes a connectionless association among the selected DSAPs. Configuring a Maintenance association End Point (MEP) at each of the DSAPs creates a Maintenance Association (MA) to monitor that connectionless connectivity. The MA is identified by a Short MA Name that is unique within the Maintenance Domain and chosen to facilitate easy identification of the Service Instance. Together, the Maintenance Domain Name and the Short MA Name form the Maintenance Association Identifier (MAID) that is carried in CFM Messages to identify incorrect connectivity among Service Instances. A small integer, the Maintenance association End Point Identifier (MEPID), identifies each MEP among those configured on a single MA (802.1ag clauses 3.19 and 18.2). This table uses two indices, first index is the index of the Maintenance Domain table. The second index is the same as the index of the dot1agCfmMaCompEntry for the same MA. The writable objects in this table need to be persistent upon reboot or restart of a device.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCfm2MaEntry

zxAnCfm2MaEntry 1.3.6.1.4.1.3902.1082.80.45.2.2.2.1
The MA table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCfm2MaEntry  

zxAnCfm2MaIndex 1.3.6.1.4.1.3902.1082.80.45.2.2.2.1.1
Index of the MA table zxAnCfm2MdMaNextIndex needs to be inspected to find an available index for row-creation.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..512  

zxAnCfm2MaFormat 1.3.6.1.4.1.3902.1082.80.45.2.2.2.1.2
The type (and thereby format) of the Maintenance Association Name.
Status: current Access: read-create
OBJECT-TYPE    
  Dot1agCfmMaintAssocNameType  

zxAnCfm2MaName 1.3.6.1.4.1.3902.1082.80.45.2.2.2.1.3
The Short Maintenance Association name. The type/format of this object is determined by the value of the zxAnCfm2MaFormat object. This name MUST be unique within a maintenance domain.
Status: current Access: read-create
OBJECT-TYPE    
  Dot1agCfmMaintAssocName  

zxAnCfm2MaCcmInterval 1.3.6.1.4.1.3902.1082.80.45.2.2.2.1.4
Interval between CCM (Continuity Check Messages) transmissions to be used by all MEPs in the MA. When set this variable, value 0 is not supported.
Status: current Access: read-create
OBJECT-TYPE    
  Dot1agCfmCcmInterval  

zxAnCfm2MaPrimarySVid 1.3.6.1.4.1.3902.1082.80.45.2.2.2.1.5
Primary SVLAN ID of the MEP.
Status: current Access: read-create
OBJECT-TYPE    
  VlanId  

zxAnCfm2MaPrimaryCVid 1.3.6.1.4.1.3902.1082.80.45.2.2.2.1.6
Primary CVLAN ID of the MEP. Value 0 means the primary CVLAN is not configured.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4094  

zxAnCfm2MaCcmTimeoutCoefficient 1.3.6.1.4.1.3902.1082.80.45.2.2.2.1.7
CCM check timeout coefficient. The CCM check timeout is the result of zxAnCfm2MaCcmTimeoutCoefficient multiplied by zxAnCfm2MaCcmInterval, and then divided by 10.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 10..500  

zxAnCfm2MaRowStatus 1.3.6.1.4.1.3902.1082.80.45.2.2.2.1.50
The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnCfm2MaEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

zxAnCfm2LocalMepTable 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2
The Maintenance Association End Point (MEP) table. Each row in the table represents a different MEP. An MEP is an actively managed CFM entity, associated with a specific DSAP of a Service Instance, which can generate and receive CFM PDUs and track any responses. It is an end point of a single Maintenance Association, and is an endpoint of a separate Maintenance Entity for each of the other MEPs in the same Maintenance Association (802.1ag clause 3.19). This table uses three indices. The first two indices are the indices of the Maintenance Domain and MA tables, the reason being that an MEP is always related to an MA and Maintenance Domain.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCfm2LocalMepEntry

zxAnCfm2LocalMepEntry 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1
The local MEP table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCfm2LocalMepEntry  

zxAnCfm2MpIdentifier 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.1
Integer that is unique among all the MEPs in the same MA. Other definition is: a small integer, unique over a given Maintenance Association, identifying a specific Maintenance association End Point (3.19). MEP Identifier is also known as the MEPID.
Status: current Access: not-accessible
OBJECT-TYPE    
  Dot1agCfmMepId  

zxAnCfm2LMepIfIndex 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.2
The index of the NNI/UNI ports on the device.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndex  

zxAnCfm2LMepSubIfIndex 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.3
The sub-interface of the NNI/UNI ports on the device.
Status: current Access: read-create
OBJECT-TYPE    
  ZxAnSubIfIndex  

zxAnCfm2LMepDirection 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.4
The direction in which the MEP faces on the Bridge port.
Status: current Access: read-create
OBJECT-TYPE    
  Dot1agCfmMpDirection  

zxAnCfm2LMepAdminStatus 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.5
The administrative status of the MEP.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

zxAnCfm2LMepLowestPriDefect 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.6
An integer value specifying the lowest priority defect that is allowed to generate fault alarm.
Status: current Access: read-create
OBJECT-TYPE    
  Dot1agCfmLowestAlarmPri  

zxAnCfm2LMepCcmSendEnable 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.7
Enable/disable sending CCM messages.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

zxAnCfm2LMepCcmLtmPriority 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.8
The priority value for CCMs and LTMs transmitted by the MEP. Default Value is the highest priority value allowed to pass through the bridge port for any of this MEPs VIDs. The management entity can obtain the default value for this variable from the priority regeneration table by extracting the highest priority value in this table on this MEPs bridge port. (1 is lowest, then 2, then 0, then 3-7).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

zxAnCfm2LMepCcmDestMacType 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.9
The destination MAC address type of CCM packet.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER unicast(1), multicast(2)  

zxAnCfm2LMepCcmRdiSendEnable 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.10
Enable/disable RDI sending in CCM packet.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

zxAnCfm2LMepCcmRdiTrustEnable 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.11
Enable/disable trusting the CCM packet from remote MEP with RDI.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

zxAnCfm2LMepCciSentCcms 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.12
The total number of CCM packets transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2LMepFngState 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.13
Current state of the MEP Fault Notification Generator State Machine.
Status: current Access: read-only
OBJECT-TYPE    
  Dot1agCfmFngState  

zxAnCfm2LMepHighestPriDefect 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.14
The highest priority defect that has been present since the MEPs Fault Notification Generator State Machine was last in the FNG_RESET state.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER defRdiCcm(1), defMacStatus(2), defRemoteCcm(3), defErrorCcm(4), defUnexpectedPeriod(5), defUnexpectedMac(6), defUnexpectedMepId(7), defXconCcm(8), defUnexpectedMegLevel(9), defAis(10), none(255)  

zxAnCfm2LMepDefects 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.15
A vector of Boolean error conditions from Table 20-1, any of which may be true: DefRDICCM(0) DefMACstatus(1) DefRemoteCCM(2) DefErrorCCM(3) DefXconCCM(4)
Status: current Access: read-only
OBJECT-TYPE    
  Dot1agCfmMepDefects  

zxAnCfm2LMepAisEnable 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.16
Enable/disable the ETH-AIS function.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

zxAnCfm2LMepAisLckInterval 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.17
The interval for AISMs and LCKMs transmitted by the MEP.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER oneSecond(1), oneMinute(2)  

zxAnCfm2LMepAisPriority 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.18
Priority. 3 bit value to be used in the VLAN tag, if present in the AIS frame.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

zxAnCfm2LMepAisCondition 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.19
Whether the MEP is in AIS condition or not.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER in(1), notIn(2)  

zxAnCfm2LMepClientMegLevel 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.20
MEG level at which the most immediate client layer MIPs and MEPs exist, zxAnCfm2LMepClientMegLevel, must be higher than the MD level. For example, configure client level list values '01 03 05 FF FF FF FF' to an MEP. It means that in the client level list only level 1, level 3 and level 5 take effect. Please notice: the range of this object is 0~7. Each client level in the list must be larger than the MD level of the MEP. '0xff' means client level not configured. The number of these client level is fixed with 7.
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(7)  

zxAnCfm2LMepMacAddress 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.21
The MAC address of the MEP.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

zxAnCfm2LMepDmTwoWayFdMsrR1Max 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.22
The maximum value of the first two-way frame delay measurements range. The minimum value is 0.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..1000000  

zxAnCfm2LMepDmTwoWayFdMsrR2Max 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.23
The maximum value of the second two-way frame delay measurements range. The minimum value is zxAnCfm2LMepDmTwoWayFdMsrR1Max.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..1000000  

zxAnCfm2LMepDmTwoWayFdMsrR3Max 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.24
The maximum value of the third two-way frame delay measurements range. The minimum value is zxAnCfm2LMepDmTwoWayFdMsrR2Max. This value is also the minimum value of the fourth two-way frame delay measurements range. The maximum value of the fourth range is plus infinity.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..1000000  

zxAnCfm2LMepDmOneWayIfdvMsrR1Max 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.25
The maximum value of the first one-way inter-frame delay variation measurements range. The minimum value is 0.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..1000000000  

zxAnCfm2LMepDmOneWayIfdvMsrR2Max 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.26
The maximum value of the second one-way inter-frame delay variation measurements range. The minimum value is zxAnCfm2LMepDmOneWayIfdvMsrR1Max.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..1000000000  

zxAnCfm2LMepDmOneWayIfdvMsrR3Max 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.27
The maximum value of the third one-way inter-frame delay variation measurements range. The minimum value is zxAnCfm2LMepDmOneWayIfdvMsrR2Max. This value is also the minimum value of the fourth one-way inter-frame delay variation measurements range. The maximum value of the fourth range is plus infinity.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 1..1000000000  

zxAnCfm2LMepRowStatus 1.3.6.1.4.1.3902.1082.80.45.2.3.2.2.1.50
The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnCfm2LocalMepEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

zxAnCfm2RemoteMepTable 1.3.6.1.4.1.3902.1082.80.45.2.3.3.2
This table includes remote MEP configuration. A remote MEP is an MEP, it can use in all the CFM tests. It represents the destination of the test when the test uses MEPID as its destination.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCfm2RemoteMepEntry

zxAnCfm2RemoteMepEntry 1.3.6.1.4.1.3902.1082.80.45.2.3.3.2.1
The remote MEP table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCfm2RemoteMepEntry  

zxAnCfm2RMepMacAddress 1.3.6.1.4.1.3902.1082.80.45.2.3.3.2.1.1
The MAC address of the remote MEP.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

zxAnCfm2RMepAdminStatus 1.3.6.1.4.1.3902.1082.80.45.2.3.3.2.1.2
The administrative status of the remote MEP.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

zxAnCfm2RMepRowStatus 1.3.6.1.4.1.3902.1082.80.45.2.3.3.2.1.50
The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnCfm2RemoteMepEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

zxAnCfm2MipTable 1.3.6.1.4.1.3902.1082.80.45.2.3.4.2
This table includes MIP configuration. An MIP can be used in all the CFM tests. MIP is a CFM entry, associated with a single Maintenance Domain, and thus with single MD level, it can generate CFM PDUs, but only in response to received CFM PDUs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCfm2MipEntry

zxAnCfm2MipEntry 1.3.6.1.4.1.3902.1082.80.45.2.3.4.2.1
The MIP table entry. When a manager wants to create a remote MEP, it must comply with the multi-variables usage rule that all the mib variables related to same fuction must be in one snmp set operation, the variables have two type: mandatory and optional. Mandatory variables must be in the one snmp set operation. Optional variables may be in the one snmp set operation with the mandatory variables, but must not be used alone. To create an MIP, there are two cases base on the MIP is assigned to a physical port or a logical port, and the mandatory and optional variables for each case are different. To create an MIP assign to physical port: - mandatoty: zxAnCfm2MipRowStatus zxAnCfm2MipIfIndex - optional : zxAnCfm2MipSubIfIndex zxAnCfm2MipIfIndex, zxAnCfm2MipSubIfIndex can not be modified.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCfm2MipEntry  

zxAnCfm2MipIfIndex 1.3.6.1.4.1.3902.1082.80.45.2.3.4.2.1.1
The index of the NNI/UNI ports on the device.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndex  

zxAnCfm2MipSubIfIndex 1.3.6.1.4.1.3902.1082.80.45.2.3.4.2.1.2
The sub-interface of the NNI/UNI ports on the device.
Status: current Access: read-create
OBJECT-TYPE    
  ZxAnSubIfIndex  

zxAnCfm2MipRowStatus 1.3.6.1.4.1.3902.1082.80.45.2.3.4.2.1.50
The status of this conceptual row. The supported actions of this conceptual row only include: 'createAndGo' and 'destroy'. To create a row in this table, a manager must set this object to createAndGo(4), and must comply with the multi-variables binding rule described in zxAnCfm2MipEntry. To delete a row in this table, a manager must set this object to destroy(6). To get this object, the agent always returns active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

zxAnCfm2MepLoopBackOperTable 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2
The Maintenance Association End Point (MEP) connectivity operation table stores all the managed objects for sending LBM. LBM Managed objects in the MEP table enables the management entity to initiate transmission of Loopback messages. It will signal the MEP that it SHOULD transmit some number of Loopback messages and detect the detection (or lack thereof) of the corresponding Loopback messages. Steps to use entries in this table: 1) Wait for zxAnCfm2MepTransLbmEnable value to be disabled. To do this do this sequence: a. an SNMP GET for both snmpSetSerialNo and zxAnCfm2MepTransLbmEnable objects (in same SNMP PDU). b. Check if value for zxAnCfm2MepTransLbmEnable is disabled. - if not, wait x seconds, go to step a above. - if enabled, save the value of snmpSetSerialNo and go to step 2) below 2) Change zxAnCfm2MepTransLbmEnable value from disabled to enabled to ensure no other management entity will use the service. In order to not disturb a possible other NMS do this by sending an SNMP SET for both snmpSetSerialNo and zxAnCfm2MepTransLbmEnable objects (in same SNMP PDU, and make sure snmpSetSerialNo is the first varBind). For the snmpSetSerialNo varBind, use the value that you obtained in step 1)a.. This ensures that two cooperating NMSes will not step on each others toes. Setting this MIB object does not set the corresponding LBIactive state machine variable. 3) Setup the different data to be sent (number of messages, optional TLVs,...). 4) Record the current values of zxAnCfm2MepLbrInInOrder, zxAnCfm2MepLbrInOutOfOrder, and zxAnCfm2MepLbrBadMsdu. 5) Check the value of zxAnCfm2MepTransLbmResultOk to find out if the operation was successfully initiated or not. 6) Monitor the value of zxAnCfm2MepTransLbmEnable. When it is reset to false, the last LBM has been transmitted. Wait an additional 5 seconds to ensure that all LBRs have been returned. 7) Compare zxAnCfm2MepLbrInInOrder, zxAnCfm2MepLbrInOutOfOrder, and zxAnCfm2MepLbrBadMsdu to their old values from step 4, above, to get the results of the test.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCfm2MepLoopBackOperEntry

zxAnCfm2MepLoopBackOperEntry 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1
The Loopback table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCfm2MepLoopBackOperEntry  

zxAnCfm2MepTransLbmEnable 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.1
Enable/disable the LBM function.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

zxAnCfm2MepTransLbmMessages 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.2
The total number of Loopback messages to be transmitted.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..200  

zxAnCfm2MepLbmDestMacType 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.3
The destination MAC address type of LBM packet.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER unicast(1), multicast(2)  

zxAnCfm2MepLbAppType 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.4
The application type of LBM. It means to verify bidirectional connectivity of an MEP with an MIP or a peer MEP.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER connectivity(1)  

zxAnCfm2MepTransLbmDestMacAddr 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.5
The Target MAC Address Field to be transmitted: A unicast destination MAC address. This address will be used if the value of the column zxAnCfm2MepTransLbmDestMepType is 'macAddr'.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

zxAnCfm2MepTransLbmDestMepId 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.6
The Maintenance association End Point Identifier of another MEP in the same Maintenance Association to which the LBM is to be sent. This address will be used if the value of the column zxAnCfm2MepTransLbmDestMepType is 'mepId'.
Status: current Access: read-write
OBJECT-TYPE    
  Dot1agCfmMepIdOrZero  

zxAnCfm2MepTransLbmDestMepType 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.7
The MEP type. macAddr(1): The unicast destination MAC address of the target MEP is used for Loopback transmission. mepId(2): The MEP ID of the target MEP is used for Loopback transmission.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER macAddr(1), mepId(2)  

zxAnCfm2MepTransLbmDataTlvLength 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.8
An arbitrary amount of data to be included in the Data TLV, if the Data TLV is selected to be sent. The value 0 means not configured and no data tlv is included in the frame.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1450  

zxAnCfm2MepTransLbmVlanPriority 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.9
The priority. 3 bit value to be used in the VLAN tag, if present in the transmitted frame. The default value is CCM priority.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..7  

zxAnCfm2MepTransLbmTimeout 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.10
LMB timeout. If the MEP does not receive LBR in time, the LBR packets may be discarded.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..10  

zxAnCfm2MepTransLbmResultOk 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.30
The result of the operation: yes(1): The Loopback Message(s) will be (or has been) sent. no(2): The Loopback Message(s) will not be sent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

zxAnCfm2MepTransLbmSeqNumber 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.31
The Loopback Transaction Identifier (zxAnCfm2MepNextLbmTransId) of the first LBM (to be) sent. The value returned is undefined if zxAnCfm2MepTransLbmResultOk is false.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

zxAnCfm2MepNextLbmTransId 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.32
Next sequence number/transaction identifier to be sent in a Loopback message. This sequence number can be zero because it wraps around.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

zxAnCfm2MepLbrInInOrder 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.33
The total number of valid, in-order Loopback Replies received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2MepLbrInOutOfOrder 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.34
The total number of valid, out-of-order Loopback Replies received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2MepLbrBadMsdu 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.35
The total number of LBRs received whose mac_service_data_unit did not match (except for the OpCode) that of the corresponding LBM (20.2.3).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2MepLbrOut 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.36
The total number of Loopback Replies transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2MepLbMaxLatency 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.37
The maximum latency.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepLbMinLatency 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.38
The minimum latency.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepLbAvgLatency 1.3.6.1.4.1.3902.1082.80.45.2.3.21.2.1.39
The average latency.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepMultiLbrTable 1.3.6.1.4.1.3902.1082.80.45.2.3.21.3
This table includes multicast Loopback result. Before start a mulitcast LBM user must first get all the entry of this table, and after the LBM is over, user must get all the entry of this table again, and compare all the entry to get the result of multicast LBM.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCfm2MepMultiLbrEntry

zxAnCfm2MepMultiLbrEntry 1.3.6.1.4.1.3902.1082.80.45.2.3.21.3.1
The multicast Lookback Reply table entry. All the varibles in this entry is read only.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCfm2MepMultiLbrEntry  

zxAnCfm2MepMultiLbrDestMepMac 1.3.6.1.4.1.3902.1082.80.45.2.3.21.3.1.1
The mac address of the destination MEP.
Status: current Access: not-accessible
OBJECT-TYPE    
  MacAddress  

zxAnCfm2MepMultiLbrMepLbrIn 1.3.6.1.4.1.3902.1082.80.45.2.3.21.3.1.2
The total LBR packets received by the MEP from the same remote MEP that responsed the LBR PDUs when received LBM from the local MEP.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2MepMultiLbMaxLatency 1.3.6.1.4.1.3902.1082.80.45.2.3.21.3.1.3
The maximum latency.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepMultiLbMinLatency 1.3.6.1.4.1.3902.1082.80.45.2.3.21.3.1.4
The minimum latency.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepMultiLbAvgLatency 1.3.6.1.4.1.3902.1082.80.45.2.3.21.3.1.5
The average latency.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepLinkTraceOperTable 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4
The Maintenance Association End Point (MEP) LinkTrace operation table stores all the managed objects for sending LTM. LTM Managed objects in the MEP table enables the management entity to initiate transmission of LinkTrace messages. It will signal the MEP that it SHOULD transmit some number of LinkTrace messages and detect the detection (or lack thereof) of the corresponding LinkTrace messages. Steps to use entries in this table: 1) Wait for zxAnCfm2MepTransLtmEnable value to be disabled. To do this do this sequence: a. an SNMP GET for both snmpSetSerialNo and zxAnCfm2MepTransLtmEnable objects (in same SNMP PDU). b. Check if value for zxAnCfm2MepTransLtmEnable is disabled. - if not, wait x seconds, go to step a above. - if enabled, save the value of snmpSetSerialNo and go to step 2) below 2) Change zxAnCfm2MepTransLtmEnable value from disabled to enabled to ensure no other management entity will use the service. In order to not disturb a possible other NMS do this by sending an SNMP SET for both snmpSetSerialNo and zxAnCfm2MepTransLtmEnable objects (in same SNMP PDU, and make sure snmpSetSerialNo is the first varBind). For the snmpSetSerialNo varBind, use the value that you obtained in step 1)a.. This ensures that two cooperating NMSes will not step on each others toes. Setting this MIB object does not set the corresponding LBIactive state machine variable. 3) Setup the different data to be sent (number of messages, ,...). 4) Check the value of zxAnCfm2MepTransLtmResultOk to find out if the operation was successfully initiated or not. 5) Monitor the value of zxAnCfm2MepTransLtmEnable. When it is reset to false, the last LTM has been transmitted. Wait an additional 5 seconds to ensure that all LTRs have been returned. 6) Read the zxAnCfm2MepLinkTraceReplyTable to get the results of the test.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCfm2MepLinkTraceOperEntry

zxAnCfm2MepLinkTraceOperEntry 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1
The LinkTrace table entry. All the varibles writable in the entry can be modified after the MEP entry created, and the variables are reset when the entry is destroyed.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCfm2MepLinkTraceOperEntry  

zxAnCfm2MepTransLtmEnable 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.1
Enable/disable the LTM function.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

zxAnCfm2MepTransLtmFlags 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.2
The flags field for LTMs transmitted by the MEP.
Status: current Access: read-create
OBJECT-TYPE    
  BITS useFDBonly(0)  

zxAnCfm2MepTransLtmDestMacAddr 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.3
The Target MAC Address Field to be transmitted: A unicast destination MAC address. This address will be used if the value of the column zxAnCfm2MepTransLtmTargetMepType is 'macAddr'.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

zxAnCfm2MepTransLtmTargetMepId 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.4
An indication of the Target MAC Address Field to be transmitted: The Maintenance association End Point Identifier of another MEP in the same Maintenance Association This address will be used if the value of the column zxAnCfm2MepTransLtmTargetMepType is 'mepId'.
Status: current Access: read-create
OBJECT-TYPE    
  Dot1agCfmMepIdOrZero  

zxAnCfm2MepTransLtmTargetMepType 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.5
The MEP type. macAddr(1): The unicast destination MAC address of the target MEP is used for LinkTrace transmission. mepId(2): The MEPID of the target MEP is used for LinkTrace transmission.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER macAddr(1), mepId(2)  

zxAnCfm2MepTransLtmTtl 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.6
The LTM TTL field. The TTL field indicates the number of hops remaining to the LTM. Decremented by 1 by each LTR (Link Trace Responder) that handles the LTM. The value returned in the LTR is one less than that received in the LTM. If the LTM TTL is 0 or 1, the LTM is not forwarded to the next hop, and if 0, no LTR is generated.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..255  

zxAnCfm2MepTransLtmTimeout 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.7
The LTM timeout. If the MEP does not receive LTR in time, the LTR packets may be discarded.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 5..10  

zxAnCfm2MepTransLtmResultOk 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.30
The result of the operation: yes(1): The LinkTrace Message(s) will be (or has been) sent. no(2): The LinkTrace Message(s) will not be sent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

zxAnCfm2MepTransLtmSeqNumber 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.31
The LTM Transaction Identifier (zxAnCfm2MepLtmNextSeqNumber) of the LTM sent. The value returned is undefined if zxAnCfm2MepTransLtmResultOk is false.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

zxAnCfm2MepLtmNextSeqNumber 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.32
Next transaction identifier/sequence number to be sent in a LinkTrace message. This sequence number can be zero because it wraps around.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

zxAnCfm2MepUnexpLtrIn 1.3.6.1.4.1.3902.1082.80.45.2.3.21.4.1.33
The total number of unexpected LTRs received (20.39.1).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2MepLinkTraceReplyTable 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5
This table extends the MEP table and contains a list of LinkTrace replies received by a specific MEP in response to a LinkTrace message. SNMP SMI does not allow to state in a MIB that an object in a table is an array. The solution is to take the index (or indices) of the first table and add one or more indices.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCfm2MepLinkTraceReplyEntry

zxAnCfm2MepLinkTraceReplyEntry 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1
The LinkTrace Reply table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCfm2MepLinkTraceReplyEntry  

zxAnCfm2MepLtrSeqNumber 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.1
Transaction identifier/Sequence number returned by a previous transmit LinkTrace message command, indicating which LTM's response is going to be returned.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..4294967295  

zxAnCfm2MepLtrReceiveOrder 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.2
An index to distinguish among multiple LTRs with the same LTR Transaction Identifier field value. zxAnCfm2MepLtrReceiveOrder are assigned sequentially from 1, in the order that the LinkTrace Initiator received the LTRs.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..4294967295  

zxAnCfm2MepLtrTtl 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.3
TTL field value for a returned LTR.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

zxAnCfm2MepLtrForwarded 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.4
Whether a LTM was forwarded by the responding MP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER forwarded(1), notForwarded(2)  

zxAnCfm2MepLtrTerminalMep 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.5
Whether the forwarded LTM reached a MEP enclosing its MA.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

zxAnCfm2MepLtrLastEgressId 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.6
An octet field holding the Last Egress Identifier returned in the LTR Egress Identifier TLV of the LTR. The Last Egress Identifier identifies the MEP LinkTrace Initiator that originated, or the LinkTrace Responder that forwarded, the LTM to which this LTR is the response. This is the same value as the Egress Identifier TLV of that LTM.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

zxAnCfm2MepLtrNextEgressId 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.7
An octet field holding the Next Egress Identifier returned in the LTR Egress Identifier TLV of the LTR. The Next Egress Identifier Identifies the LinkTrace Responder that transmitted this LTR, and can forward the LTM to the next hop. This is the same value as the Egress Identifier TLV of the forwarded LTM, if any. If the FwdYes bit of the Flags field is false, the contents of this field are undefined, i.e. any value can be transmitted, and the field is ignored by the receiver.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

zxAnCfm2MepLtrRelay 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.8
Value returned in the Relay Action field.
Status: current Access: read-only
OBJECT-TYPE    
  Dot1agCfmRelayActionFieldValue  

zxAnCfm2MepLtrIngress 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.9
The value returned in the Ingress Action Field of the LTM.
Status: current Access: read-only
OBJECT-TYPE    
  Dot1agCfmIngressActionFieldValue  

zxAnCfm2MepLtrIngressMac 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.10
MAC address returned in the ingress MAC address field.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

zxAnCfm2MepLtrEgress 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.11
The value returned in the Egress Action Field of the LTM.
Status: current Access: read-only
OBJECT-TYPE    
  Dot1agCfmEgressActionFieldValue  

zxAnCfm2MepLtrEgressMac 1.3.6.1.4.1.3902.1082.80.45.2.3.21.5.1.12
MAC address returned in the egress MAC address field.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

zxAnCfm2MepDmOperTable 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2
The Maintenance Association End Point (MEP) performance measurement operation table stores all the managed objects for sending DMM. Steps to use entries in this table: 1) Wait for zxAnCfm2MepDmEnable value to be disabled. To do this do this sequence: a. an SNMP GET for both snmpSetSerialNo and zxAnCfm2MepDmEnable objects (in same SNMP PDU). b. Check if value for zxAnCfm2MepDmEnable is disabled. - if not, wait x seconds, go to step a above. - if enabled, save the value of snmpSetSerialNo and go to step 2) below 2) Change zxAnCfm2MepDmEnable value from disabled to enabled to ensure no other management entity will use the service. In order to not disturb a possible other NMS do this by sending an SNMP SET for both snmpSetSerialNo and zxAnCfm2MepDmEnable and other delay measurement objects (such as zxAnCfm2MepDmPriority,...) (in same SNMP PDU, and make sure snmpSetSerialNo is the first varbind). For the snmpSetSerialNo varbind, use the value that you obtained in step 1) a. This ensures that two cooperating NMSes will not step on each others toes. 3) Check the value of zxAnCfm2MepDmResultOk to find out if the operation was successfully initiated or not. 4) Monitor the value of zxAnCfm2MepDmEnable. When it is reset to false, the last DMM has been transmitted. 5) Get the results of the test from zxAnCfm2MepDmRltTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCfm2MepDmOperEntry

zxAnCfm2MepDmOperEntry 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1
The Delay Measurement table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCfm2MepDmOperEntry  

zxAnCfmMepDmTestId 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.1
The frame delay measurement identifier of the specified MEP. 8 measurements can be simultaneously activated on the MEP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..8  

zxAnCfm2MepDmEnable 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.2
Enable/disable the DM function. If the value is disable, the DM test can not be started.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

zxAnCfm2MepDmTargetMepId 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.3
The Maintenance association End Point Identifier of another MEP in the same Maintenance Association to which the DM is to be sent. It will be used if DMM destination MAC address type is unicast.
Status: current Access: read-create
OBJECT-TYPE    
  Dot1agCfmMepIdOrZero  

zxAnCfm2MepDmFrameSize 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.4
The DM frame size.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER size66(1), size128(2), size256(3), size512(4), size1024(5), size1280(6), size1518(7)  

zxAnCfm2MepDmAppType 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.5
The application type of the DM.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER singleEnded(1), dualEnded(2)  

zxAnCfm2MepDmInterval 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.6
The interval at which DMMs are sent by an MEP.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER interval1s(1), interval10s(2), interval60s(3), interval100s(4)  

zxAnCfm2MepDmDuration 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.7
The duration of DM test. It can be configured when zxAnCfm2MepDmOperType is onDemand.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 10..86400  

zxAnCfm2MepDmPriority 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.8
The priority. 3 bit value to be used in the VLAN tag, if present in the transmitted frame.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

zxAnCfm2MepDmOperType 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.9
The operation type of the DM.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER onDemand(1), proactive(2)  

zxAnCfm2MepDmResultOk 1.3.6.1.4.1.3902.1082.80.45.2.3.22.2.1.30
The result of the operation: yes(1): The Delay Measurement Message(s) will be (or has been) sent. no(2): The Delay Measurement Message(s) will not be sent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

zxAnCfm2MepDmRltTable 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3
This table includes multicast or unicast frame delay measurement result.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCfm2MepDmRltEntry

zxAnCfm2MepDmRltEntry 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1
The delay measurement result table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCfm2MepDmRltEntry  

zxAnCfm2DmRemoteMepId 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.1
Remote MEP identifier, which receives frame delay measurement packets and responses delay measurement reply packets.
Status: current Access: not-accessible
OBJECT-TYPE    
  Dot1agCfmMepId  

zxAnCfm2MepDmStartTime 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.2
The timestamp of the time-of-day in UTC at the scheduled starting time of the measurement interval.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

zxAnCfm2MepDmEndTime 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.3
The timestamp of the time-of-day in UTC at the scheduled ending time of the measurement interval.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

zxAnCfm2MepDmElapsedTime 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.4
The elapsed time of the delay measurement interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmSentPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.5
The packets of delay measurement sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2MepDmReceivedPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.6
The packets of delay measurement received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2MepDmTwoWayFdMsr 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.7
The count of two-way frame delay measurements.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2MepDmTwoWayFdMsrAvg 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.8
The average two-way frame delay measurements.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmTwoWayFdMsrMin 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.9
The minimum two-way frame delay measurements.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmTwoWayFdMsrMax 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.10
The maximum two-way frame delay measurements.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmOneWayFwdIfdvMsr 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.11
The count of inter-frame delay variation measurements in the forward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2MepDmOneWayFwdIfdvMsrAvg 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.12
The average one-way inter-frame delay variation measurements in forward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmOneWayFwdIfdvMsrMax 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.13
The maximum one-way inter-frame delay variation measurements in forward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmOneWayFwdIfdvMsrMin 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.14
The minimum one-way inter-frame delay variation measurements in forward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmOneWayBwdIfdvMsr 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.15
The count of inter-frame delay variation measurements in the backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2MepDmOneWayBwdIfdvMsrAvg 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.16
The average one-way inter-frame delay variation measurements in backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmOneWayBwdIfdvMsrMax 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.17
The maximum one-way inter-frame delay variation measurements in backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmOneWayBwdIfdvMsrMin 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.18
The minimum one-way inter-frame delay variation measurements in backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmTwoWayFdMsrR1C 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.19
The count in the first two-way frame delay measurements range which is [0, zxAnCfm2LMepDmTwoWayFdMsrR1Max).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmTwoWayFdMsrR2C 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.20
The count in the second two-way frame delay measurements range which is [zxAnCfm2LMepDmTwoWayFdMsrR1Max, zxAnCfm2LMepDmTwoWayFdMsrR2Max).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmTwoWayFdMsrR3C 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.21
The count in the third two-way frame delay measurements range which is [zxAnCfm2LMepDmTwoWayFdMsrR2Max, zxAnCfm2LMepDmTwoWayFdMsrR3Max).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmTwoWayFdMsrR4C 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.22
The count in the fourth two-way frame delay measurements range which is [zxAnCfm2LMepDmTwoWayFdMsrR3Max, plus infinity).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmOneWayFwdIfdvMsrR1C 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.23
The count in the first one-way inter-frame delay variation measurements range which is [0, zxAnCfm2LMepDmOneWayIfdvMsrR1Max) in the forward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmOneWayFwdIfdvMsrR2C 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.24
The count in the second one-way inter-frame delay variation measurements range which is [zxAnCfm2LMepDmOneWayIfdvMsrR1Max, zxAnCfm2LMepDmOneWayIfdvMsrR2Max) in the forward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmOneWayFwdIfdvMsrR3C 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.25
The count in the third one-way inter-frame delay variation measurements range which is [zxAnCfm2LMepDmOneWayIfdvMsrR2Max, zxAnCfm2LMepDmOneWayIfdvMsrR3Max) in the forward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmOneWayFwdIfdvMsrR4C 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.26
The count in the fourth one-way inter-frame delay variation measurements range which is [zxAnCfm2LMepDmOneWayIfdvMsrR3Max, plus infinity) in the forward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmOneWayBwdIfdvMsrR1C 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.27
The count in the first one-way inter-frame delay variation measurements range which is [0, zxAnCfm2LMepDmOneWayIfdvMsrR1Max) in the backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmOneWayBwdIfdvMsrR2C 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.28
The count in the second one-way inter-frame delay variation measurements range which is [zxAnCfm2LMepDmOneWayIfdvMsrR1Max, zxAnCfm2LMepDmOneWayIfdvMsrR2Max) in the backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmOneWayBwdIfdvMsrR3C 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.29
The count in the third one-way inter-frame delay variation measurements range which is [zxAnCfm2LMepDmOneWayIfdvMsrR2Max, zxAnCfm2LMepDmOneWayIfdvMsrR3Max) in the backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepDmOneWayBwdIfdvMsrR4C 1.3.6.1.4.1.3902.1082.80.45.2.3.22.3.1.30
The count in the fourth one-way inter-frame delay variation measurements range which is [zxAnCfm2LMepDmOneWayIfdvMsrR3Max, plus infinity) in the backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepLmOperTable 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4
The Maintenance Association End Point (MEP) performance measurement operation table stores all the managed objects for sending LMM. Steps to use entries in this table: 1) Wait for zxAnCfm2MepLmEnable value to be disabled. To do this do this sequence: a. an SNMP GET for both snmpSetSerialNo and zxAnCfm2MepLmEnable objects (in same SNMP PDU). b. Check if value for zxAnCfm2MepLmEnable is disabled. - if not, wait x seconds, go to step a above. - if enabled, save the value of snmpSetSerialNo and go to step 2) below 2) Change zxAnCfm2MepLmEnable value from disabled to enabled to ensure no other management entity will use the service. In order to not disturb a possible other NMS do this by sending an SNMP SET for both snmpSetSerialNo and zxAnCfm2MepLmEnable and other frame loss measurement objects (such as zxAnCfm2MepLmPriority,...) (in same SNMP PDU, and make sure snmpSetSerialNo is the first varBind). For the snmpSetSerialNo varbind, use the value that you obtained in step 1) a. This ensures that two cooperating NMSes will not step on each others toes. 3) Check the value of zxAnCfm2MepLmResultOk to find out if the operation was successfully initiated or not. 4) Monitor the value of zxAnCfm2MepLmEnable. When it is reset to false, the last LMM has been transmitted. 5) Get the results of the test from zxAnCfm2MepLmRltTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCfm2MepLmOperEntry

zxAnCfm2MepLmOperEntry 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1
The Loss Measurement table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCfm2MepLmOperEntry  

zxAnCfm2MepLmTestId 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1.1
The packet loss measurement identifier of the specified MEP, only one on-demand or one proactive LM can be activated simultaneously on the specified MEP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2  

zxAnCfm2MepLmEnable 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1.2
Enable/disable the LM function. If the value is disable the LM test can not be started.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

zxAnCfm2MepLmTargetMepId 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1.3
The Maintenance association End Point Identifier of another MEP in the same Maintenance Association to which the LM is to be sent. This variable will be used if the LMM destination MAC address type is unicast, if not configured the multicast LM will be sent.
Status: current Access: read-create
OBJECT-TYPE    
  Dot1agCfmMepIdOrZero  

zxAnCfm2MepLmAppType 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1.4
The application type of the LM.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER singleEnded(1), dualEnded(2)  

zxAnCfm2MepLmInterval 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1.5
The interval at which LMMs are sent by an MEP.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER interval1s(1), interval10s(2), interval60s(3), interval100s(4)  

zxAnCfm2MepLmDuration 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1.6
The duration of LM. It can be configured when zxAnCfm2MepLmOperType is onDemand.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 10..86400  

zxAnCfm2MepLmPriority 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1.7
The priority. 3 bit value to be used in the VLAN tag, if present in the LM frame.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

zxAnCfm2MepLmOperType 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1.8
The operation type of the LM.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER onDemand(1), proactive(2)  

zxAnCfm2MepLmResultOk 1.3.6.1.4.1.3902.1082.80.45.2.3.22.4.1.30
The result of the operation: yes(1): The Loss Measurement Message(s) will be (or has been) sent. no(2): The Loss Measurement Message(s) will not be sent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

zxAnCfm2MepLmRltTable 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5
This table includes multicast or unicast frame loss measurement result.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCfm2MepLmRltEntry

zxAnCfm2MepLmRltEntry 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1
The loss measurement result table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCfm2MepLmRltEntry  

zxAnCfm2LmRemoteMepId 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.1
Remote MEP identifier, which receives frame loss measurement packets and responses loss measurement reply packets.
Status: current Access: not-accessible
OBJECT-TYPE    
  Dot1agCfmMepId  

zxAnCfm2MepLmStartTime 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.2
The timestamp of the time-of-day in UTC at the scheduled starting time of the measurement interval.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

zxAnCfm2MepLmEndTime 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.3
The timestamp of the time-of-day in UTC at the scheduled ending time of the measurement interval.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

zxAnCfm2MepLmElapsedTime 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.4
The elapsed time of the measurement interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepLmSentPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.5
The number of frame loss measurement packets sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2MepLmReceivedPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.6
The number of frame loss measurement packets received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2MepLmFwdSentPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.7
The number of frame loss measurement packets sent in forward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

zxAnCfm2MepLmFwdReceivedPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.8
The number of frame loss measurement packets received in forward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

zxAnCfm2MepLmFwdLossRatio 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.9
The frame loss ratio in forward direction of the LM.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepLmBwdSentPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.10
The number of frame loss measurement packets sent in backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

zxAnCfm2MepLmBwdReceivedPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.11
The number of frame loss measurement packets received in backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

zxAnCfm2MepLmBwdLossRatio 1.3.6.1.4.1.3902.1082.80.45.2.3.22.5.1.12
The frame loss ratio in backward direction of the LM.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepSlmOperTable 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6
The Maintenance Association End Point (MEP) performance measurement operation table stores all the managed objects for sending SLM . Steps to use entries in this table: 1) Wait for zxAnCfm2MepSlmEnable value to be disabled. To do this do this sequence: a. an SNMP GET for both snmpSetSerialNo and zxAnCfm2MepSlmEnable objects (in same SNMP PDU). b. Check if value for zxAnCfm2MepSlmEnable is disabled. - if not, wait x seconds, go to step a above. - if enabled, save the value of snmpSetSerialNo and go to step 2) below 2) Change zxAnCfm2MepSlmEnable value from disabled to enabled to ensure no other management entity will use the service. In order to not disturb a possible other NMS do this by sending an SNMP SET for both snmpSetSerialNo and zxAnCfm2MepSlmEnable and other synthetic loss measurement objects (such as zxAnCfm2MepSlmPriority, ...) (in same SNMP PDU, and make sure snmpSetSerialNo is the first varbind). For the snmpSetSerialNo varBind, use the value that you obtained in step 1) a. This ensures that two cooperating NMSes will not step on each others toes. 3) Check the value of zxAnCfm2MepSlmResultOk to find out if the operation was successfully initiated or not. 4) Monitor the value of zxAnCfm2MepSlmEnable. When it is reset to false, the last SLM has been transmitted. 5) Get the results of the test from the zxAnCfm2MepSlmRltTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCfm2MepSlmOperEntry

zxAnCfm2MepSlmOperEntry 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1
The synthetic loss measurement table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCfm2MepSlmOperEntry  

zxAnCfm2MepSlmTestId 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.1
The synthetic frame loss measurement identifier of the specified MEP. 8 measurements can be activated simultaneously on the MEP.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..8  

zxAnCfm2MepSlmEnable 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.2
Enable/disable the SLM function. If the value is disable the SLM test can not be started.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

zxAnCfm2MepSlmTargetMepId 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.3
The Maintenance Association End Point Identifier of another MEP in the same Maintenance Association to which the SLM is to be sent. This variable will be used if the SLM destination MAC address type is unicast, if 0, the SLM destination MAC address type is multicast.
Status: current Access: read-create
OBJECT-TYPE    
  Dot1agCfmMepIdOrZero  

zxAnCfm2MepSlmAppType 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.4
The application type of the SLM.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER singleEnded(1), dualEnded(2)  

zxAnCfm2MepSlmInterval 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.5
The interval at which SLM is send by an MEP. Unlimited means the test can't stop until the user stops it.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER interval10ms(1), interval100ms(2), interval1s(3), unlimited(255)  

zxAnCfm2MepSlmDuration 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.6
The duration of SLM test.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 10..600  

zxAnCfm2MepSlmPriority 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.7
The priority. 3 bit value to be used in the VLAN tag, if present in the SLM frame.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

zxAnCfm2MepSlmFrameSize 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.8
The packet length of the SLM frame.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER size64(1), size128(2), size256(3), size512(4), size1024(5), size1280(6), size1518(7)  

zxAnCfm2MepSlmOperType 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.9
The operation type of the SLM.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER onDemand(1), proactive(2)  

zxAnCfm2MepSlmResultOk 1.3.6.1.4.1.3902.1082.80.45.2.3.22.6.1.30
The result of the operation: yes(1): The Synthetic Loss Measurement Message(s) will be (or has been) sent. no(2): The Synthetic Loss Measurement Message(s) will not be sent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER yes(1), no(2)  

zxAnCfm2MepSlmRltTable 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7
The synthetic frame loss measurement result table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCfm2MepSlmRltEntry

zxAnCfm2MepSlmRltEntry 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1
The result information of Synthetic Loss Measurement.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCfm2MepSlmRltEntry  

zxAnCfm2SlmRemoteMepId 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.1
Remote MEP identifier, which receives synthetic frame loss measurement packets and responses synthetic frame loss reply packets.
Status: current Access: not-accessible
OBJECT-TYPE    
  Dot1agCfmMepId  

zxAnCfm2MepSlmStartTime 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.2
The timestamp of the time-of-day in UTC at the scheduled starting time of the measurement interval.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

zxAnCfm2MepSlmEndTime 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.3
The timestamp of the time-of-day in UTC at the scheduled ending time of the measurement interval.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime  

zxAnCfm2MepSlmElapsedTime 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.4
The elapsed time of the measurement interval.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepSlmSentPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.5
The number of synthetic loss measurement packets sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2MepSlmReceivedPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.6
The number of synthetic loss measurement packets received.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2MepSlmFwdSentPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.7
The number of synthetic loss measurement packets sent in forward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2MepSlmFwdReceivedPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.8
The number of synthetic loss measurement packets received in forward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2MepSlmFwdLossPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.9
The packets loss in the latest SLM in forward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepSlmFwdLossRatio 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.10
The packet loss ratio of the latest SLM in forward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepSlmBwdSentPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.11
The number of synthetic loss measurement packets sent in backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2MepSlmBwdReceivedPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.12
The number of synthetic loss measurement packets received in backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

zxAnCfm2MepSlmBwdLossPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.13
The packets loss of the latest SLM in backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepSlmBwdLossRatio 1.3.6.1.4.1.3902.1082.80.45.2.3.22.7.1.14
The packet loss ratio of the latest SLM in backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

zxAnCfm2MepStatsTable 1.3.6.1.4.1.3902.1082.80.45.2.3.23.2
The MEP (Maintenance Association End Point) statistics table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ZxAnCfm2MepStatsEntry

zxAnCfm2MepStatsEntry 1.3.6.1.4.1.3902.1082.80.45.2.3.23.2.1
The MEP statistics table entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  ZxAnCfm2MepStatsEntry  

zxAnCfm2MepStatsRxPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.23.2.1.1
The total number of received CFM packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

zxAnCfm2MepStatsTxPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.23.2.1.2
The total number of transmitted CFM packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

zxAnCfm2MepStatsRxSequenceErrors 1.3.6.1.4.1.3902.1082.80.45.2.3.23.2.1.3
The total number of received out-of-sequence CFM packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

zxAnCfm2MepStatsRxSrcMacErrors 1.3.6.1.4.1.3902.1082.80.45.2.3.23.2.1.4
The total number of received CFM packets that source MAC address is invalid.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

zxAnCfm2MepStatsRxCorrectPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.23.2.1.5
The total number of received correct CFM packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

zxAnCfm2MepStatsRxIllegalPkts 1.3.6.1.4.1.3902.1082.80.45.2.3.23.2.1.6
The total number of received illegal CFM packets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

zxAnCfm2MepStatsReset 1.3.6.1.4.1.3902.1082.80.45.2.3.23.2.1.100
Clear all the MEP statistics variables. When get this variable, always return 1.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER reset(1)  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor