ZHONE-COM-BRIDGE-REC-MIB

File: ZHONE-COM-BRIDGE-REC-MIB.mib (140082 bytes)

Imported modules

ATM-TC-MIB IF-MIB RFC1213-MIB
SNMP-FRAMEWORK-MIB SNMPv2-CONF SNMPv2-SMI
SNMPv2-TC Zhone Zhone-TC

Imported symbols

AtmVpIdentifier AtmVcIdentifier ifIndex
ifAlias InterfaceIndex ifPhysAddress
PhysAddress SnmpAdminString OBJECT-GROUP
NOTIFICATION-GROUP IpAddress Integer32
Unsigned32 Counter64 OBJECT-TYPE
MODULE-IDENTITY OBJECT-IDENTITY NOTIFICATION-TYPE
TruthValue MacAddress TEXTUAL-CONVENTION
zhone zhoneBridge zhoneModules
ZhoneAdminString ZhoneRowStatus

Defined Types

PacketRuleGroupIndex  
Description.
TEXTUAL-CONVENTION    
  Integer32 0..2147483647  

EapsState  
EAPS State Values (per RFC 3619bis). IDLE = 0x00 (EAPS Domain (Master/Transit) still not running) COMPLETE = 0x01 (Master in complete State) FAILED = 0x02 (Master in Failed State) LINKS-UP = 0x03 (Transit in links-up State. Both ring-ports are up) LINK-DOWN = 0x04 (Transit in Link-Down State. One or both ring-ports are down) PREFORWARDING = 0x05 (Transit in Preforwarding State) INIT = 0x06 (Master in Init State)
TEXTUAL-CONVENTION    
  INTEGER idle(0), complete(1), failed(2), links-up(3), link-down(4), preForwarding(5), init(6)  

BridgeState  
state as shown in 'bridge show'.
TEXTUAL-CONVENTION    
  INTEGER up(1), down(2), trouble(3), notAvailable(4), initializing(5), adminDown(6), adminStateTest(7), adminStateNone(8), ready(9), discovering(10), unknown(11), blocked(12), pending(13), disabled(14), learning(15), forwarding(16), blockedFlapping(17), blockedPersistent(18), blockedFlappingPersistent(19)  

NetworkAddress  
OCTET STRING    

BridgeInterfaceEntry  
SEQUENCE    
  bridgeIfVpi AtmVpIdentifier
  bridgeIfVci AtmVcIdentifier
  bridgeIfVlanId Integer32
  bridgeIfStripAndInsert TruthValue
  bridgeIfCustomARP TruthValue
  bridgeIfFilterBroadcast TruthValue
  bridgeIfLearnIp TruthValue
  bridgeIfLearnUnicast TruthValue
  bridgeIfMaxUnicast Integer32
  bridgeIfLearnMulticast TruthValue
  bridgeIfForwardToUnicast TruthValue
  bridgeIfForwardToMulticast TruthValue
  bridgeIfForwardToDefault TruthValue
  bridgeLowerIfIndex InterfaceIndex
  bridgeIfRowStatus ZhoneRowStatus
  bridgeIfCustomDHCP TruthValue
  bridgeIfIngressPacketRuleGroupIndex PacketRuleGroupIndex
  bridgeIfVlanIdCOS Integer32
  bridgeIfOutgoingCOSOption INTEGER
  bridgeIfOutgoingCOSValue Integer32
  bridgeIfStagTPID Integer32
  bridgeIfStagId Integer32
  bridgeIfStagStripAndInsert TruthValue
  bridgeIfStagOutgoingCOSOption INTEGER
  bridgeIfStagCOS Integer32
  bridgeIfStagOutgoingCOSValue Integer32
  bridgeIfMcastControlList SnmpAdminString
  bridgeIfMaxVideoStreams Unsigned32
  bridgeIfIsPPPoA TruthValue
  bridgeIfFloodUnknown TruthValue
  bridgeIfFloodMulticast TruthValue
  bridgeIfEgressPacketRuleGroupIndex PacketRuleGroupIndex
  bridgeIfTableBasedFilter BITS
  bridgeIfDhcpLearn BITS
  bridgeIfOnDemandStatsEnabled INTEGER
  bridgeIfMvrVlan Integer32
  bridgeIfVlanXlateFrom Integer32
  bridgeIfSlanXlateFrom Integer32
  bridgeIfBridgeState BridgeState
  bridgeIfUnblock TruthValue
  bridgeType INTEGER
  bridgeIfGponGemPortId Unsigned32
  bridgeIfGponTrafficProfile Unsigned32
  bridgeIfIncomingCOSOption INTEGER
  bridgeIfStagIncomingCOSOption INTEGER

StaticBridgeEntry  
SEQUENCE    
  staticBridgeMacOrIpAddress PhysAddress
  staticBridgeAddressType INTEGER
  staticBridgeMulticastAging Integer32
  staticBridgeRowStatus ZhoneRowStatus
  staticBridgeFlapControl INTEGER
  staticBridgeUnicastAging Integer32
  staticBridgeIgmpQueryInterval Integer32
  staticBridgeFlags BITS
  staticBridgeIgmpCustomIpAddress IpAddress
  staticBridgeLoopPrevention INTEGER
  staticBridgeIgmpDscp OCTET STRING

BridgeIfLookupEntry  
SEQUENCE    
  bridgeIfAddressType INTEGER
  bridgeIfMacOrIpAddress PhysAddress
  bridgeIfLookupStaticOrDynamic INTEGER
  bridgeIfLookupFlush TruthValue

BridgeAddressLookupEntry  
SEQUENCE    
  bridgeAddressLookupStaticOrDynamic INTEGER
  bridgeAddressLookupFlush TruthValue

PacketRuleGroupNextIndexEntry  
SEQUENCE    
  packetRuleGroupMemberNextIndex PacketRuleGroupIndex

PacketRuleEntry  
SEQUENCE    
  packetRuleGroupMemberIndex Integer32
  packetRuleType INTEGER
  packetRuleValue SnmpAdminString
  packetRuleRowStatus ZhoneRowStatus
  packetRuleValue2 SnmpAdminString
  packetRuleValue3 SnmpAdminString
  packetRuleValue4 SnmpAdminString
  packetRuleValue5 SnmpAdminString
  packetRuleGroupIndex PacketRuleGroupIndex
  packetRuleValue6 SnmpAdminString
  packetRuleValue7 SnmpAdminString

BridgePPPoEEntry  
SEQUENCE    
  bridgePPPoEBrasMac OCTET STRING
  bridgePPPoELocalHostMac OCTET STRING
  bridgePPPoEEIfIndex InterfaceIndex
  bridgePPPoESessionID Integer32
  bridgePPPoESlanId Integer32
  bridgePPPoEVlanId Integer32
  bridgePPPoEEncapLLC INTEGER

StpBindEntry  
SEQUENCE    
  stpBindInstanceID Unsigned32
  stpBindRowStatus ZhoneRowStatus
  stpBindPortPriority Unsigned32

MstpInstanceEntry  
SEQUENCE    
  mstpInstanceRowStatus ZhoneRowStatus
  mstpInstanceName ZhoneAdminString

BridgeStatsEntry  
SEQUENCE    
  bridgeStatsUcastRcvd Unsigned32
  bridgeStatsMcastRcvd Unsigned32
  bridgeStatsBcastRcvd Unsigned32
  bridgeStatsUcastSent Unsigned32
  bridgeStatsMcastSent Unsigned32
  bridgeStatsBcastSent Unsigned32
  bridgeStatsErrorSent Unsigned32
  bridgeOnDemandStatsRulesSupported Unsigned32
  bridgeOnDemandStatsRulesRemaining Unsigned32
  bridgeStatsBSDUcastBlocked Unsigned32
  bridgeStatsBSDMcastBlocked Unsigned32
  bridgeStatsBSDBcastBlocked Unsigned32
  bridgeStatsBSDAlarmCount Unsigned32
  bridgeStatsBytesRcvdCount Counter64
  bridgeStatsBytesSentCount Counter64
  bridgeStatsTicksLastCleared Counter64
  bridgeStatsTicksNow Counter64
  bridgeStatsTicksPerSecond Counter64

EapsConfigEntry  
SEQUENCE    
  eapsConfigPrimaryPortLineGroup InterfaceIndex
  eapsConfigSecondaryPortLineGroup InterfaceIndex
  eapsConfigControlVlan Integer32
  eapsConfigIsMasterNode TruthValue
  eapsConfigControlVlanPriority Integer32
  eapsConfigDomainName ZhoneAdminString
  eapsConfigMsgTxInterval Integer32
  eapsConfigTimeout Integer32
  eapsConfigMaxDroppedMessages Integer32
  eapsConfigSnmpTrap TruthValue
  eapsConfigDomainEnable TruthValue
  eapsConfigRowStatus ZhoneRowStatus

EapsProtectedVlanEntry  
SEQUENCE    
  eapsProtectedVlanEntryIndex Integer32
  eapsProtectedVlanLowerRange Integer32
  eapsProtectedVlanUpperRange Integer32
  eapsProtectedVlanRowStatus ZhoneRowStatus
  eapsProtectedVlanDomainName ZhoneAdminString

EapsStatusEntry  
SEQUENCE    
  eapsPrevState EapsState
  eapsState EapsState

EapsStatsEntry  
SEQUENCE    
  eapsStatsTotCtrlMsgSent Integer32
  eapsStatsTotCtrlMsgRecvd Integer32

EapsTopologyEntry  
SEQUENCE    
  eapsTopologyRing INTEGER
  eapsTopologyRowNumber Integer32
  eapsTopologyDomainName ZhoneAdminString
  eapsTopologyMacAddr MacAddress
  eapsTopologyIpAddr IpAddress
  eapsTopologyType INTEGER
  eapsTopologyPrimaryLinkName ZhoneAdminString
  eapsTopologyPrimaryLinkState EapsState
  eapsTopologySecondaryLinkName ZhoneAdminString
  eapsTopologySecondaryLinkState EapsState

BridgeIgmpStatsEntry  
SEQUENCE    
  genQueryRx Unsigned32
  genQueryTx Unsigned32
  specQueryRx Unsigned32
  specQueryTx Unsigned32
  v2ReportsRx Unsigned32
  v2ReportsTx Unsigned32
  leavesRx Unsigned32
  leavesTx Unsigned32
  unknownRx Unsigned32
  errorRx Unsigned32
  actChans Unsigned32
  actHosts Unsigned32
  v3GenQueryRx Unsigned32
  v3GenQueryTx Unsigned32
  v3SpecQueryRx Unsigned32
  v3SpecQueryTx Unsigned32
  v3ReportsRx Unsigned32
  v3ReportsTx Unsigned32

BridgeIgmpEntry  
SEQUENCE    
  slanId Integer32
  vlanId Integer32
  mcastMac OCTET STRING
  mcastIP IpAddress
  hostMac OCTET STRING
  lastJoinTimer Integer32

StaticBridgePathEntry  
SEQUENCE    
  staticBridgePathMacOrIpAddress NetworkAddress
  staticBridgePathAddressType INTEGER
  staticBridgePathMulticastAging Integer32
  staticBridgePathRowStatus ZhoneRowStatus
  staticBridgePathFlapControl INTEGER
  staticBridgePathUnicastAging Integer32
  staticBridgePathIgmpQueryInterval Integer32
  staticBridgePathFlags BITS
  staticBridgePathIgmpCustomIpAddress IpAddress
  staticBridgePathLoopPrevention INTEGER
  staticBridgePathIgmpDscp OCTET STRING

BridgePathIfLookupEntry  
SEQUENCE    
  bridgePathIfAddressType INTEGER
  bridgePathIfMacOrIpAddress NetworkAddress
  bridgePathIfLookupStaticOrDynamic INTEGER
  bridgePathIfLookupFlush TruthValue

BridgePathAddressLookupEntry  
SEQUENCE    
  bridgePathAddressLookupStaticOrDynamic INTEGER
  bridgePathAddressLookupFlush TruthValue

BridgeStatusEntry  
SEQUENCE    
  bridgeStatusState BridgeState

Defined Values

bridgeRecord 1.3.6.1.4.1.5504.6.77
BRIDGE record MIB IP Software Minneapolis, MN
MODULE-IDENTITY    

bridgeInterfaceGroup 1.3.6.1.4.1.5504.4.7.1
The bridge Interface Record object group.
Status: current Access: read-only
OBJECT-GROUP    

bridgeInterfaceTable 1.3.6.1.4.1.5504.4.7.2
This table contains information required for the management of bridge interfaces.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BridgeInterfaceEntry

bridgeInterfaceEntry 1.3.6.1.4.1.5504.4.7.2.1
An entry exists for each bridge interface in the system. At a mininum the ifIndex must be present to create a row.
Status: current Access: not-accessible
OBJECT-TYPE    
  BridgeInterfaceEntry  

bridgeIfVpi 1.3.6.1.4.1.5504.4.7.2.1.1
If this bridge interface is on an ATM VC, the ATM VPI is specified here. If the bridge interface is not an ATM VC, this field is ignored. The VPI value for a VPL or VCL. The value VPI=0 is only allowed for a VCL. For ATM UNIs supporting VPCs the VPI value ranges from 0 to 255. The VPI value 0 is supported for ATM UNIs conforming to the ATM Forum UNI 4.0 Annex 8 (Virtual UNIs) specification. For ATM UNIs supporting VCCs the VPI value ranges from 0 to 255. For ATM NNIs the VPI value ranges from 0 to 4095. The maximum VPI value cannot exceed the value allowable by atmInterfaceMaxVpiBits defined in ATM-MIB.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVpIdentifier  

bridgeIfVci 1.3.6.1.4.1.5504.4.7.2.1.2
If this bridge interface is on an ATM VC, the ATM VCI is specified here. The range is 32...65535. The maximum VCI value cannot exceed the value allowable by atmInterfaceMaxVciBits defined in ATM-MIB. If the bridge interface is not an ATM VC, but for example an ethernet interface, this field should be set to 0.
Status: current Access: read-create
OBJECT-TYPE    
  AtmVcIdentifier  

bridgeIfVlanId 1.3.6.1.4.1.5504.4.7.2.1.3
The Virtual LAN Id for VLAN Tag Insertion.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

bridgeIfStripAndInsert 1.3.6.1.4.1.5504.4.7.2.1.4
If true, enable VLAN Tagging.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

bridgeIfCustomARP 1.3.6.1.4.1.5504.4.7.2.1.5
If true, send ARP requests selectively or by flood.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

bridgeIfFilterBroadcast 1.3.6.1.4.1.5504.4.7.2.1.6
If true, discard non-ARP broadcast packets.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

bridgeIfLearnIp 1.3.6.1.4.1.5504.4.7.2.1.7
If true, snoop unicast packets to build ARP table.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

bridgeIfLearnUnicast 1.3.6.1.4.1.5504.4.7.2.1.8
If true, snoop unicast packets to build MAC paths.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

bridgeIfMaxUnicast 1.3.6.1.4.1.5504.4.7.2.1.9
Maximum number of unicast addresses for I/F.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

bridgeIfLearnMulticast 1.3.6.1.4.1.5504.4.7.2.1.10
If true, snoop multicast packets for IGMP joins/leaves.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

bridgeIfForwardToUnicast 1.3.6.1.4.1.5504.4.7.2.1.11
If true, attempt to forward via unicast MAC paths.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

bridgeIfForwardToMulticast 1.3.6.1.4.1.5504.4.7.2.1.12
If true, attempt to forward via multicast MAC paths.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

bridgeIfForwardToDefault 1.3.6.1.4.1.5504.4.7.2.1.13
If true, attempt to forward via VLAN default paths.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

bridgeLowerIfIndex 1.3.6.1.4.1.5504.4.7.2.1.14
An entry exists for each bridge interface in the system. Only Ifindex and lower if index is needed to create a row.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndex  

bridgeIfRowStatus 1.3.6.1.4.1.5504.4.7.2.1.15
This object is used to create and remove rows in the table. See bridgeInterfaceEntry description for minimum requirements.
Status: current Access: read-create
OBJECT-TYPE    
  ZhoneRowStatus  

bridgeIfCustomDHCP 1.3.6.1.4.1.5504.4.7.2.1.16
If TRUE, forwards broadcast DHCPOFFER or DHCPACK packets even if bridgeFilterBroadcast is TRUE for that interface.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

bridgeIfIngressPacketRuleGroupIndex 1.3.6.1.4.1.5504.4.7.2.1.17
Index used as partial address of a group of entries in the packetRuleTable, each of which prescribes a filtering condition for the ingress interface.
Status: current Access: read-create
OBJECT-TYPE    
  PacketRuleGroupIndex  

bridgeIfVlanIdCOS 1.3.6.1.4.1.5504.4.7.2.1.18
The Class-Of-Service (COS) value used for VLAN Tag Insertion.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

bridgeIfOutgoingCOSOption 1.3.6.1.4.1.5504.4.7.2.1.19
Determines COS setting on packets bridged out this interface. disable - COS setting is untouched. all - COS will be set to bridgeIfOutgoingCOSValue.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER outgoingCOSOptionDisable(1), outgoingCOSOptionAll(2)  

bridgeIfOutgoingCOSValue 1.3.6.1.4.1.5504.4.7.2.1.20
The COS value loaded into outgoing tagged packets. Applicable only if interface sends tagged packets and bridgeIfOutgoingCOSOption is outgoingCOSOption_all.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

bridgeIfStagTPID 1.3.6.1.4.1.5504.4.7.2.1.21
The value of the tag protocol identifier that is being used for QinQ packets. (0x8100 is default.)
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 33024 | 34984 | 37120 | 37376  

bridgeIfStagId 1.3.6.1.4.1.5504.4.7.2.1.22
The s-tag value that we are expecting to put on packets that are Rxed on this interface.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

bridgeIfStagStripAndInsert 1.3.6.1.4.1.5504.4.7.2.1.23
If true, enable S-tag tagging on this IF.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

bridgeIfStagOutgoingCOSOption 1.3.6.1.4.1.5504.4.7.2.1.24
Determines s-tag COS settings on packets bridged out this interface: disable - s-tag COS setting just passed as Rxed. all - s-tag COS will be set with s_tagOutgoingCOSValue.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER sTagCOSDisable(1), sTagCOSAll(2)  

bridgeIfStagCOS 1.3.6.1.4.1.5504.4.7.2.1.25
The s-tag COS to be used when doing s-tag insertion.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

bridgeIfStagOutgoingCOSValue 1.3.6.1.4.1.5504.4.7.2.1.26
The s-tag COS value loaded into outgoing tagged packets. Applicaple only if interface sends S-tagged packets and s_tagOutgoingCOSOption is All.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

bridgeIfMcastControlList 1.3.6.1.4.1.5504.4.7.2.1.27
List of mcast-control-ids this bridge-interface-record is associated with. It is an integer stored as string, and controls which channels a user can watch. Note: unlike for IP, an empty list here allows user to watch all channels.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

bridgeIfMaxVideoStreams 1.3.6.1.4.1.5504.4.7.2.1.28
Maximum number of multicast (video) streams that we will support.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..1024  

bridgeIfIsPPPoA 1.3.6.1.4.1.5504.4.7.2.1.29
If true, this interface accepts PPPoA packets and will bridge them out as PPPoE packets.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

bridgeIfFloodUnknown 1.3.6.1.4.1.5504.4.7.2.1.30
If true, flood frames with unknown unicast MAC address that would otherwise be discarded.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

bridgeIfFloodMulticast 1.3.6.1.4.1.5504.4.7.2.1.31
If true, flood all multicast traffic received on this bridge to all other ports on this vlan.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

bridgeIfEgressPacketRuleGroupIndex 1.3.6.1.4.1.5504.4.7.2.1.32
Index used as partial address of a group of entries in the packetRuleTable, each of which prescribes a filtering condition for the egress interface.
Status: current Access: read-create
OBJECT-TYPE    
  PacketRuleGroupIndex  

bridgeIfTableBasedFilter 1.3.6.1.4.1.5504.4.7.2.1.33
none : Dynamic IP Filtering on bridge based on DHCP, is disabled. BIT 1(mac) : MAC address based Filtering based on DHCP, is enabled. BIT 2(ip) : IP address based dynamic IP Filtering based on DHCP, is enabled. Defval is changed to correct the Zhone script errors.
Status: current Access: read-create
OBJECT-TYPE    
  BITS mac(0), ip(1)  

bridgeIfDhcpLearn 1.3.6.1.4.1.5504.4.7.2.1.34
none :IP address and Mac address are not learned from DHCP packets. BIT 1 (mac): MAC addresses are learned from DHCP packets. ip 2 (ip) : IP addresses are learned from DHCP packets. The Defval is changed to correct the Zhone script errors.
Status: current Access: read-create
OBJECT-TYPE    
  BITS mac(0), ip(1)  

bridgeIfOnDemandStatsEnabled 1.3.6.1.4.1.5504.4.7.2.1.35
If true, the on-demand stats collection for this bridge interface will be enabled and packets will be counted. If bytes, the on-demand stats collection for this bridge interface will be enabled and abd bytes will be counted.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER true(1), false(2), bytes(3)  

bridgeIfMvrVlan 1.3.6.1.4.1.5504.4.7.2.1.36
The Multicast Vlan Registration (MVR) vlan ID. Multicast video packets with this vlan can be vlan translated out this bridge.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

bridgeIfVlanXlateFrom 1.3.6.1.4.1.5504.4.7.2.1.37
If a packet's VLAN ID value matches this object's value then the packet's VLAN ID will be translated to the value of bridgeIfVlanId. A zero value disables translation.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

bridgeIfSlanXlateFrom 1.3.6.1.4.1.5504.4.7.2.1.38
If a packet's SLAN ID value matches this object's value then the packet's SLAN ID will be translated to the value of bridgeIfStagId. A zero value disables translation.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4095  

bridgeIfBridgeState 1.3.6.1.4.1.5504.4.7.2.1.39
Values: up(1), UP down(2), DWN trouble(3), TRB notAvailable(4), NA initializing(5), INI adminDown(6), ADN adminStateTest(7), TST adminStateNone(8), N/S ready(9), RDY discovering(10), DSC unknown(11), ??? blocked(12), BLK pending(13), PND disabled(14), DIS learning(15), LRN forwarding(16), FWD blockedFlapping(17), BLF blockedPersistent(18), BLP blockedFlappingPersistenr(19), BFP
Status: current Access: read-create
OBJECT-TYPE    
  BridgeState  

bridgeIfUnblock 1.3.6.1.4.1.5504.4.7.2.1.40
Set to TRUE to unblock a bridge that is blocked due to flapping.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

bridgeType 1.3.6.1.4.1.5504.4.7.2.1.41
bridge type
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER uplink(1), downlink(2), intralink(4), tls(6), rlink(8), pppoa(9), wire(10), mvr(11), user(12), downlinkVideo(13), downlinkData(14), downlinkPPPoE(15), downlinkP2P(16), downlinkVoice(17), downlinkUpstreamMcast(18), ipobTls(19), ipobUplink(20), ipobDownlink(21)  

bridgeIfGponGemPortId 1.3.6.1.4.1.5504.4.7.2.1.42
GPON GEM Port ID used only to create a bridge on a GPON ONU.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

bridgeIfGponTrafficProfile 1.3.6.1.4.1.5504.4.7.2.1.43
GPON Traffic Profile Index used only to create a bridge on a GPON ONU.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

bridgeIfIncomingCOSOption 1.3.6.1.4.1.5504.4.7.2.1.44
Determines COS settings on incoming packets bridged out this interface: disable - COS replcement feature is disabled all - COS will be set with vlanIDCOS.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER incomingCOSOptionDisable(1), incomingCOSOptionAll(2)  

bridgeIfStagIncomingCOSOption 1.3.6.1.4.1.5504.4.7.2.1.45
Determines s-tag COS settings on incoming packets bridged out this interface: disable - s-tag COS setting just passed as Rxed. all - s-tag COS will be set with s-tagIdCOS.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER stagIncomingCOSOptionDisable(1), stagIncomingCOSOptionAll(2)  

staticBridgeTable 1.3.6.1.4.1.5504.4.7.3
A collection of staticBridgeEntries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    StaticBridgeEntry

staticBridgeEntry 1.3.6.1.4.1.5504.4.7.3.1
Static Bridge entries are created by the user in order to specify forwarding for a particular interface, vlanId, mac address or ip address, slanId (for QinQ). The INDEX value for staticBridgeEntry consists of following 5 values: ifIndex staticBridgeAddressType bridgeIfVlanId staticBridgeMacOrIpAddress bridgeIfStagId If staticBridgeAddressType is set to macAddr(1), then staticBridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress are used for the bridge path. If staticBridgeAddressType is set to ipAddr(2), then staticBridgeMacOrIpAddress represents an IP Address, and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress are used for the bridge path. If staticBridgeAddressType is set to vlanIdAddr(3), then ifIndex and bridgeIfVlanId are used for the bridge path. If staticBridgeAddressType is set to globalAddr(4), then ifIndex is used for the bridge path.
Status: current Access: not-accessible
OBJECT-TYPE    
  StaticBridgeEntry  

staticBridgeMacOrIpAddress 1.3.6.1.4.1.5504.4.7.3.1.1
If the staticBridgeAddressType is set to macAddr(1), then this field represents a MAC address. If the staticBridgeAddressType is set to ipAddr(2), then this field represents an IP address.
Status: current Access: not-accessible
OBJECT-TYPE    
  PhysAddress Size(6)  

staticBridgeAddressType 1.3.6.1.4.1.5504.4.7.3.1.2
If staticBridgeAddressType is set to macAddr(1), then staticBridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress are used for the bridge path. If staticBridgeAddressType is set to ipAddr(2), then staticBridgeMacOrIpAddress represents an IP Address, and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress are used for the bridge path. If staticBridgeAddressType is set to vlanIdAddr(3) or intralinkAddr(7), then ifIndex and bridgeIfVlanId are used for the bridge path. If staticBridgeAddressType is set to globalAddr(4), globalIntralinkAddr(8), or mvrAddr(13) then ifIndex is used for the bridge path. If staticBridgeAddressType is set to dhcpAllowOui( 720901) then the first 3 bytes of the MAC address contains the OUI that we will allow DHCP addresses to be granted to, global scope. If staticBridgeAddressType is set to dhcpIpAddr(9), or to dhcpMacAddr(10), then the other fields are populated as for address types ipAddr and macAddr respectively, with the difference that these are secure entries, learned by snooping DHCP. If staticBridgeAddressType is set to vlanParms(14), then the static bridge entry holds parameters for the given VLAN and SLAN ID (for example, flap mode, unicast aging period, etc) and is not associated with any specific bridge, but with all bridges with the same VLAN/SLAN ID. For this reason, the IfIndex of this entry must be zero. If staticBridgeAddressType is set to secMvrAddr(15), then the static bridge entry holds parameters for a Secondary MVR path. The VLAN ID of this entry is the Secondary VLAN ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER macAddr(1), ipAddr(2), vlanIdAddr(3), globalAddr(4), intralinkAddr(7), globalIntralinkAddr(8), dhcpIpAddr(9), dhcpMacAddr(10), mvrAddr(13), vlanParms(14), secMvrAddr(15), dhcpAllowOui(720901)  

staticBridgeMulticastAging 1.3.6.1.4.1.5504.4.7.3.1.3
Multicast Aging period in tenths of seconds for the specified VLAN. After the specified aging period is met, the VLAN address is deleted from the routing table. A value of 0 indicates that aging is turned off. Maximum value is 2147483647 tenths of seconds, which equates to approximately 2485.51 days.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

staticBridgeRowStatus 1.3.6.1.4.1.5504.4.7.3.1.4
Used to create, modify or delete an entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  ZhoneRowStatus  

staticBridgeFlapControl 1.3.6.1.4.1.5504.4.7.3.1.5
This object enables or disable Flap Control in the Bridge Filter Table. The value 'disable(2)' turns Flap Control mode off. The values 'enable(3)' or 'fast(4) turn flap control mode on. 'Enable(3)' applies a hold time of 60 secs before allowing addr/IP to be moved to a new port, while 'fast(4)' applies a hold time of 0 secs. A value of 'default(1)' indicates 'Don't Care' and defaults to a disable or enable set by another entry.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER default(1), disable(2), enable(3), fast(4)  

staticBridgeUnicastAging 1.3.6.1.4.1.5504.4.7.3.1.6
Multicast Aging period in tenths of seconds for the specified VLAN. After the specified aging period is met, the VLAN address is deleted from the routing table. A value of 0 indicates that aging is turned off. Maximum value is 2147483647 tenths of seconds, which equates to approximately 2485.51 days.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0 | 120..2147483647  

staticBridgeIgmpQueryInterval 1.3.6.1.4.1.5504.4.7.3.1.7
How often (in seconds) we as a bridge inject IGMP query values into the stream.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

staticBridgeFlags 1.3.6.1.4.1.5504.4.7.3.1.8
none : IGMP Snooping with Proxy reporting is disabled. BIT 0(igmpProcessJoinAndLeave) : igmpProcessJoinandLeave is enabled for IGMP packets. BIT 1(igmpRespondToQuery) : igmpRespondToQuery is enabled for IGMP packets. BIT 2(igmpUseBridgeIpAddress) : igmpUseBridgeIpAddress is enabled for IGMP packets. BIT 3(forceIGMPv2Down) : forceIGMPv2Down is enabled for subscriber side BIT 4(forceIGMPv2Up) : forceIGMPv2Up is enabled for uplink/network side
Status: current Access: read-create
OBJECT-TYPE    
  BITS igmpProcessJoinAndLeave(0), igmpRespondToQuery(1), igmpUseBridgeIpAddress(2), forceIGMPv2Down(3), forceIGMPv2Up(4)  

staticBridgeIgmpCustomIpAddress 1.3.6.1.4.1.5504.4.7.3.1.9
Allow the configuration of the source IP address for packets that we originate upstream when doing IGMP Porxy on a bridge.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

staticBridgeLoopPrevention 1.3.6.1.4.1.5504.4.7.3.1.10
This field does the following options,'BlockAsym(1)' blocks a learning bridge if flap is detected between it and an uplink bridge. 'BlockAll(2)' incorporates 'blockAsym(1)' but it also blocks a learning bridge if it flaps against another learning bridge.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), blockAsym(1), blockAll(2), blockAsymAuto(3), blockAllAuto(4)  

staticBridgeIgmpDscp 1.3.6.1.4.1.5504.4.7.3.1.11
This parameter indicates DSCP value for igmp traffic. Valid code values: <0-63> Differentiated services codepoint value af11 Mark packets with AF11 dscp (001010) af12 Mark packets with AF12 dscp (001100) af13 Mark packets with AF13 dscp (001110) af21 Mark packets with AF21 dscp (010010) af22 Mark packets with AF22 dscp (010100) af23 Mark packets with AF23 dscp (010110) af31 Mark packets with AF31 dscp (011010) af32 Mark packets with AF32 dscp (011100) af33 Mark packets with AF33 dscp (011110) af41 Mark packets with AF41 dscp (100010) af42 Mark packets with AF42 dscp (100100) af43 Mark packets with AF43 dscp (100110) cs1 Mark packets with CS1(precedence 1) dscp (001000) cs2 Mark packets with CS2(precedence 2) dscp (010000) cs3 Mark packets with CS3(precedence 3) dscp (011000) cs4 Mark packets with CS4(precedence 4) dscp (100000) cs5 Mark packets with CS5(precedence 5) dscp (101000) cs6 Mark packets with CS6(precedence 6) dscp (110000) cs7 Mark packets with CS7(precedence 7) dscp (111000) default Mark packets with default dscp (000000) ef Mark packets with EF dscp (101110)
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..8)  

bridgeIfLookupTable 1.3.6.1.4.1.5504.4.7.4
A collection of bridgeIfLookupTable entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BridgeIfLookupEntry

bridgeIfLookupEntry 1.3.6.1.4.1.5504.4.7.4.1
Bridge IfLookup entries are created by the user or learned by the software in order to specify forwarding for a particular interface, vlanId/slanId, mac address or ip address. The INDEX value for bridgeIfLookupEntry consists of following 5 values: bridgeIfAddressType bridgeIfMacOrIpAddress bridgeIfVlanId ifIndex bridgeIfStagId If bridgeIfAddressType is set to unicast_mac(1), then bridgeIfMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId/Slanid and bridgeIfMacOrIpAddress are use for the bridge path. If bridgeIfAddressType is set to multicast_mac(2), then bridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId/SlanId and bridgeIfMacOrIpAddress are used for bridge path. If bridgeIfAddressType is set to ip_address(3), then ifIndex and bridgeIfVlanId/SlanId are used for the bridge path.
Status: current Access: not-accessible
OBJECT-TYPE    
  BridgeIfLookupEntry  

bridgeIfAddressType 1.3.6.1.4.1.5504.4.7.4.1.1
If bridgeIfAddressType is set to unicast_mac(1), then bridgeIfMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and bridgeIfMacOrIpAddress are used for the bridge path. If bridgeIfAddressType is set to multicast_mac(2), then bridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and bridgeIfMacOrIpAddress are used for the bridge path. If bridgeIfAddressType is set to ip_address(3), then ifIndex and bridgeIfVlanId are used for the bridge path. If bridgeIfAddressType is set to dhcp_mac(4), or dhcp_ip(5), then the address is as desribed for types 1 and 3, respectively, and the address was learned by snooping DHCP packets. ipV6Address(6) is the same as ipAddress(3) except for IPv6 address format. dhcpV6Mac(7) is the same as dhacpMac(4) except for IPv6 address format. dhcpV7Ip(8) is the same as dhcpIp(5) except for IPv6 address format.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER unicastMac(1), multicastMac(2), ipAddress(3), dhcpMac(4), dhcpIp(5), ipV6Address(6), dhcpV6Mac(7), dhcpV6Ip(8)  

bridgeIfMacOrIpAddress 1.3.6.1.4.1.5504.4.7.4.1.2
If bridgeIfAddressType is set to FILTER_ENTRY_UNICAST_MAC(1) or to FILTER_ENTRY_MULTICAST_MAC(2), or to FILTER_ENTRY_DHCP_MAC(4), then bridgeIfMacOrIpAddress represents a MAC Address. If bridgeIfAddressType is set to FILTER_ENTRY_IP_ADDRESS(3), or to FILTER_ENTRY_DHCP_IP(5), then bridgeIfMacOrIpAddress represents an IP Address.
Status: current Access: not-accessible
OBJECT-TYPE    
  PhysAddress  

bridgeIfLookupStaticOrDynamic 1.3.6.1.4.1.5504.4.7.4.1.3
If bridgeIfLookupStaticOrDynamic is set to 1, then this table entry is static and persistent. If bridgeIfLookupStaticOrDynamic is set to 2, then this table entry is learned and is not persistent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER staticEntry(1), dynamicEntry(2)  

bridgeIfLookupFlush 1.3.6.1.4.1.5504.4.7.4.1.4
The object 'bridgeIfLookupFlush' allows a user to flush learned entries in the bridgeFilterTable when the ifIndex of the entry is not known. A combination of address type, MAC or IP address and vlan ID is used to determine the ifIndex of the entry to be removed. Setting the object to 'true' causes the flush action to occur. After the flush action is taken, the value of bridgeIfLookupFlush is immediately set back to 'false'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

bridgeAddressLookupTable 1.3.6.1.4.1.5504.4.7.5
A collection of bridgeAddressLookupTable entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BridgeAddressLookupEntry

bridgeAddressLookupEntry 1.3.6.1.4.1.5504.4.7.5.1
BridgeAddressLookup entries are created by the user or learned by the software in order to specify forwarding for a particular interface, vlanId/slanId, mac address or ip address. The INDEX value for bridgeIfLookupEntry consists of following 5 values: ifIndex bridgeIfAddressType bridgeIfMacOrIpAddress bridgeIfVlanId bridgeIfStagId
Status: current Access: not-accessible
OBJECT-TYPE    
  BridgeAddressLookupEntry  

bridgeAddressLookupStaticOrDynamic 1.3.6.1.4.1.5504.4.7.5.1.1
If bridgeAddressLookupStaticOrDynamic is set to 1, then this table entry is static and persistent. If bridgeAddressLookupStaticOrDynamic is set to 2, then this table entry is learned and is not persistent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER staticEntry(1), dynamicEntry(2)  

bridgeAddressLookupFlush 1.3.6.1.4.1.5504.4.7.5.1.2
The object 'bridgeIfAddressFlush' allows a user to flush learned entries in the bridgeFilterTable when the ifIndex of the entry is known. The ifIndex is used to determine which interface is to be removed. Setting the object to 'true' causes the flush action to occur. After the flush action is taken, the value of bridgeIfLookupFlush is immediately set back to 'false'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

packetRuleGroup 1.3.6.1.4.1.5504.4.7.6
OBJECT IDENTIFIER    

packetRuleGroupIndexNext 1.3.6.1.4.1.5504.4.7.6.1
A scalar representing the next available Group Index for Packet Rule Table Entries.
Status: current Access: read-only
OBJECT-TYPE    
  PacketRuleGroupIndex  

packetRuleGroupNextIndexTable 1.3.6.1.4.1.5504.4.7.6.2
A collection of entries each representing the next available index for that group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PacketRuleGroupNextIndexEntry

packetRuleGroupNextIndexEntry 1.3.6.1.4.1.5504.4.7.6.2.1
A packetRuleGroupNextIndexEntry contains the next available index for that packetRuleGroup.
Status: current Access: not-accessible
OBJECT-TYPE    
  PacketRuleGroupNextIndexEntry  

packetRuleGroupMemberNextIndex 1.3.6.1.4.1.5504.4.7.6.2.1.1
The next index available in a given packetRuleGroup for a new packetRuleEntry.
Status: current Access: read-only
OBJECT-TYPE    
  PacketRuleGroupIndex  

packetRuleTable 1.3.6.1.4.1.5504.4.7.6.3
A collection of packetRuleEntries.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    PacketRuleEntry

packetRuleEntry 1.3.6.1.4.1.5504.4.7.6.3.1
Packet Rule entries are created by the user in order to specify filtering or other packet manipulation for a particular interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  PacketRuleEntry  

packetRuleGroupMemberIndex 1.3.6.1.4.1.5504.4.7.6.3.1.1
The index of a packetRuleEntry in a given packetRuleGroup.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 1..2147483647  

packetRuleType 1.3.6.1.4.1.5504.4.7.6.3.1.2
A 32-bit value which determines a filter to be applied to packets on the interface matching the pattern specified in packetRuleValue. The size and offset of the pattern in the packet will depend on packetRuleType. Bits may be set in packetRuleType determining properties of the filtering to be applied: BRIDGE_FORBID = 0x10 BRIDGE_INPUT = 0x20 BRIDGE_TERMINATE = 0x40 When BRIDGE_FORBID is set, packets matching the pattern are dropped; when it is clear, matching packets are forwarded. When BRIDGE_INPUT is set, filtering is applied to packets received on the interface; when it is clear, filtering is applied to packets to be transmitted on the interface. When BRIDGE_TERMINATE is set, processing of a packet matching the pattern ends the scan of filtering specifications; when it is clear, processing continues. Values of packetRuleType include DST_MAC_SWAP_STATIC = 0x25 DST_MAC_SWAP_DYNAMIC = 0x28 BRIDGE_INSERT_OPTION82 = 0x61 BRIDGE_DHCP_RELAY = 0x62 BRIDGE_INSERT_PPPOE_VENDOR_TAG = 0x63 BRIDGE_FORBID_OUI = 0x72 RATE_LIMIT_DISCARD = 0x64 COLOR_AWARE_RATE_LIMIT_DISCARD = 0x67
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER dstMacSwapStatic(37), dstMacSwapDynamic(38), dscpToCos(41), promoteFirstEncapsulationVlan(42), filterFirstEncapsulationVlan(43), promoteSecondEncapsulationVlan(44), filterSecondEncapsulationVlan(45), bridgeStormDetect(46), bridgeInsertOption82(97), dhcpRelay(98), bridgeInsertPPPoEVendorTag(99), rateLimitDiscard(100), colorAwareRateLimitDiscard(103), aclAllow(104), bridgeForbidOui(114), aclDeny(120)  

packetRuleValue 1.3.6.1.4.1.5504.4.7.6.3.1.3
A variable-length field whose meaning depends on packetRuleType. If bridgeForbidOui, it specifies a bit pattern to be matched in a packet, stored as a string, but specified in the pattern 'nn:nn:nn...nn:nn', where 'nn' is a hex number specifying a byte of the pattern. E.g. a packetRuleValue of '00:02:02' specifies the OUI to be dropped. If dhcpRelay, it is ascii integer which specifies dhcp subnet group. If bridgeInsertOption82, this value is ignored. If bridgeInsertPPPoEVendorTag, it specifies an ASCII string of up to 48 bytes to be inserted into PPPoE discovery packets (PADI/PADR) which transit this node. String will be inserted as a Vendor-Specific tag. If rateLimitDiscard, this value represents a maximum rate (in kbps). If aclAllow/aclDeny, a text string of the form: all | [Keyword NamedValue | Value[/N]]* where Keyword identifies the field of interest, Value is context dependent on the field, NamedValue is an alias for a Value. N indicates the number of most significant bits of Value to test. If omitted it defaults to the max allowed for the field.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

packetRuleRowStatus 1.3.6.1.4.1.5504.4.7.6.3.1.4
This object is used to create and remove rows in the table.
Status: current Access: read-create
OBJECT-TYPE    
  ZhoneRowStatus  

packetRuleValue2 1.3.6.1.4.1.5504.4.7.6.3.1.5
A variable-length field whose meaning depends on packetRuleType.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

packetRuleValue3 1.3.6.1.4.1.5504.4.7.6.3.1.6
A variable-length field whose meaning depends on packetRuleType.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

packetRuleValue4 1.3.6.1.4.1.5504.4.7.6.3.1.7
A variable-length field whose meaning depends on packetRuleType.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

packetRuleValue5 1.3.6.1.4.1.5504.4.7.6.3.1.8
A variable-length field whose meaning depends on packetRuleType.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

packetRuleGroupIndex 1.3.6.1.4.1.5504.4.7.6.3.1.9
A scalar representing the Group Index for a set of Packet Rule Table Entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  PacketRuleGroupIndex 0..2147483647  

packetRuleValue6 1.3.6.1.4.1.5504.4.7.6.3.1.10
A variable-length field whose meaning depends on packetRuleType.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

packetRuleValue7 1.3.6.1.4.1.5504.4.7.6.3.1.11
A variable-length field whose meaning depends on packetRuleType.
Status: current Access: read-create
OBJECT-TYPE    
  SnmpAdminString  

bridgePPPoETable 1.3.6.1.4.1.5504.4.7.7
For PPPoA-to-PPPoE tables, provide a lookup by ifIndex into the PPPoE tables. If the session has not been created for this PPPoA ifIndex, then there will be no table data.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BridgePPPoEEntry

bridgePPPoEEntry 1.3.6.1.4.1.5504.4.7.7.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  BridgePPPoEEntry  

bridgePPPoEBrasMac 1.3.6.1.4.1.5504.4.7.7.1.1
Destination mac address.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

bridgePPPoELocalHostMac 1.3.6.1.4.1.5504.4.7.7.1.2
Source mac address.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(6)  

bridgePPPoEEIfIndex 1.3.6.1.4.1.5504.4.7.7.1.3
PPPoE port's ifIndex.
Status: current Access: read-only
OBJECT-TYPE    
  InterfaceIndex  

bridgePPPoESessionID 1.3.6.1.4.1.5504.4.7.7.1.4
PPPoE session ID.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

bridgePPPoESlanId 1.3.6.1.4.1.5504.4.7.7.1.5
SLan ID of BRAS.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4094  

bridgePPPoEVlanId 1.3.6.1.4.1.5504.4.7.7.1.6
VLAN ID of BRAS.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4094  

bridgePPPoEEncapLLC 1.3.6.1.4.1.5504.4.7.7.1.7
PPPoA encapsulation
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER vcmux(1), llc(2)  

stpParam 1.3.6.1.4.1.5504.4.7.8
OBJECT IDENTIFIER    

stpParamName 1.3.6.1.4.1.5504.4.7.8.1
set this field if you are using MSTP, use the name of the bridge as a key.
Status: current Access: read-write
OBJECT-TYPE    
  ZhoneAdminString  

stpParamRevision 1.3.6.1.4.1.5504.4.7.8.2
This parameter is used if you are running MSTP only. Currently we don't support any revisions to MSTP, so revision 0 is default.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0  

stpParamBridgePriority 1.3.6.1.4.1.5504.4.7.8.3
The priority ID that will be advertised for this bridge.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 4096..61440  

stpParamForceVersion 1.3.6.1.4.1.5504.4.7.8.4
The protocol to initiate with. 3- MSTP, 2- RSTP, 0- STP.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 2 | 3  

stpParamFwdDelay 1.3.6.1.4.1.5504.4.7.8.5
The delay used by STP bridges to transition Root and Designated Ports to Forwarding.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 4..20  

stpParamHelloTime 1.3.6.1.4.1.5504.4.7.8.6
The interval between periodic transmissions of Configuration Messages by Designated Ports. We only support a hello time of 2 currently.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 2  

stpParamMigrateTime 1.3.6.1.4.1.5504.4.7.8.7
The initial value of the mdelayWhile and edgeDelayWhile timers. We currently only support a value of 3 for this timer.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 3  

stpParamTxHoldCount 1.3.6.1.4.1.5504.4.7.8.8
The transmit hold count is used by the Port Transmit state machine to limit transmission rate.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..5  

stpParamMaxAge 1.3.6.1.4.1.5504.4.7.8.9
The maximum age of the information transmitted by the bridge when it is the Root Bridge.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 6..20  

stpBindTable 1.3.6.1.4.1.5504.4.7.9
The stpBind table is used to store the entries of stpBind which hold the relationship between the ifIndex on which STP is to run on, and the MSTP instance if any.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    StpBindEntry

stpBindEntry 1.3.6.1.4.1.5504.4.7.9.1
stpBindEntry is used to specify the type of STP that is to run on an ifIndex. An InstanceID of 0 specifies RSTP. An InstanceId > 0 indicates MSTP.
Status: current Access: not-accessible
OBJECT-TYPE    
  StpBindEntry  

stpBindInstanceID 1.3.6.1.4.1.5504.4.7.9.1.1
This is a hidden storage of the InstanceId of an entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

stpBindRowStatus 1.3.6.1.4.1.5504.4.7.9.1.2
Description.
Status: current Access: read-create
OBJECT-TYPE    
  ZhoneRowStatus  

stpBindPortPriority 1.3.6.1.4.1.5504.4.7.9.1.3
PortPriority is used to specify the STP priority of this port.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..65535  

mstpInstanceTable 1.3.6.1.4.1.5504.4.7.10
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    MstpInstanceEntry

mstpInstanceEntry 1.3.6.1.4.1.5504.4.7.10.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  MstpInstanceEntry  

mstpInstanceRowStatus 1.3.6.1.4.1.5504.4.7.10.1.1
Description.
Status: current Access: read-create
OBJECT-TYPE    
  ZhoneRowStatus  

mstpInstanceName 1.3.6.1.4.1.5504.4.7.10.1.2
A name for this mstp instance and vlanId.
Status: current Access: read-create
OBJECT-TYPE    
  ZhoneAdminString  

bridgeStatsTable 1.3.6.1.4.1.5504.4.7.11
The bridgeStatsTable is used to access the statistics of the entries in the bridge table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BridgeStatsEntry

bridgeStatsEntry 1.3.6.1.4.1.5504.4.7.11.1
Displays the bridge statistics table entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  BridgeStatsEntry  

bridgeStatsUcastRcvd 1.3.6.1.4.1.5504.4.7.11.1.1
Unicast packets received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bridgeStatsMcastRcvd 1.3.6.1.4.1.5504.4.7.11.1.2
Multicast packets received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bridgeStatsBcastRcvd 1.3.6.1.4.1.5504.4.7.11.1.3
Broadcast packets received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bridgeStatsUcastSent 1.3.6.1.4.1.5504.4.7.11.1.4
Unicast packets sent.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bridgeStatsMcastSent 1.3.6.1.4.1.5504.4.7.11.1.5
Multicast packets sent.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bridgeStatsBcastSent 1.3.6.1.4.1.5504.4.7.11.1.6
Broadcast packets sent.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bridgeStatsErrorSent 1.3.6.1.4.1.5504.4.7.11.1.7
Error packets sent.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bridgeOnDemandStatsRulesSupported 1.3.6.1.4.1.5504.4.7.11.1.8
Get the number of supported Ingress Stats available for a line card.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bridgeOnDemandStatsRulesRemaining 1.3.6.1.4.1.5504.4.7.11.1.9
Get the number of remaining Ingress Stats available for a line card
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bridgeStatsBSDUcastBlocked 1.3.6.1.4.1.5504.4.7.11.1.10
Number of unicast packets dropped due to Bridge Packet Storm Detection threshold exceeded.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bridgeStatsBSDMcastBlocked 1.3.6.1.4.1.5504.4.7.11.1.11
Number of multicast packets dropped due to Bridge Packet Storm Detection threshold exceeded.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bridgeStatsBSDBcastBlocked 1.3.6.1.4.1.5504.4.7.11.1.12
Number of broadcast packets dropped due to Bridge Packet Storm Detection threshold exceeded.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bridgeStatsBSDAlarmCount 1.3.6.1.4.1.5504.4.7.11.1.13
This counter reflects the number of times this interface has transitioned to the alarm state due to the Bridge Packet Storm Detection threshold being exceeded for a pre-defined number of seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bridgeStatsBytesRcvdCount 1.3.6.1.4.1.5504.4.7.11.1.14
This is a count of the number of bytes received. On-demand stats must be enabled for byte counters otherwise this counter is zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

bridgeStatsBytesSentCount 1.3.6.1.4.1.5504.4.7.11.1.15
This is a count of the number of bytes transmitted. On-demand stats must be enabled for byte counters otherwise this counter is zero.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

bridgeStatsTicksLastCleared 1.3.6.1.4.1.5504.4.7.11.1.16
Linecard tick value when bridge was last cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

bridgeStatsTicksNow 1.3.6.1.4.1.5504.4.7.11.1.17
Linecard current tick value.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

bridgeStatsTicksPerSecond 1.3.6.1.4.1.5504.4.7.11.1.18
Linecard current tick value.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

bridgeCmd 1.3.6.1.4.1.5504.4.7.12
OBJECT IDENTIFIER    

bridgeCmdOperation 1.3.6.1.4.1.5504.4.7.12.1
Bridge command ID value.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER clrStats(1), clrIgmpStats(2), unblock(3), flush(4)  

bridgeCmdFilterMask 1.3.6.1.4.1.5504.4.7.12.2
Bridge command filters bit mask. If a bridge filter is enabled then the associated bridge filter value must be included in the SNMP packet. If the bridge filter mask is all zeros then no filters will be applied and the bridge command will apply to all bridges in the system.
Status: current Access: read-write
OBJECT-TYPE    
  BITS filterIfIndex(0), filterVlan(1), filterSlan(2), filterSlot(3), filterPort(4), filterIpAddress(5), filterMacAddress(6), filterSecure(7)  

bridgeCmdIfIndex 1.3.6.1.4.1.5504.4.7.12.3
Bridge command 'ifIndex' filter value. If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (bridgeCmdFilterMask).
Status: current Access: read-write
OBJECT-TYPE    
  InterfaceIndex  

bridgeCmdVlanId 1.3.6.1.4.1.5504.4.7.12.5
Bridge command 'VLAN' filter value. If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (bridgeCmdFilterMask).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4090  

bridgeCmdSlanId 1.3.6.1.4.1.5504.4.7.12.6
Bridge command 'SLAN' filter value. If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (bridgeCmdFilterMask).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..4090  

bridgeCmdSlot 1.3.6.1.4.1.5504.4.7.12.7
Bridge command 'SLOT' filter value. If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (bridgeCmdFilterMask).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..32  

bridgeCmdPort 1.3.6.1.4.1.5504.4.7.12.8
Bridge command 'PORT' filter value. This is the ifIndex of the linegroup on which the bridge is stacked If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (bridgeCmdFilterMask).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..2147483647  

bridgeCmdIpAddress 1.3.6.1.4.1.5504.4.7.12.9
Bridge command 'IP Address' filter value. If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (bridgeCmdFilterMask).
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

bridgeCmdMacAddress 1.3.6.1.4.1.5504.4.7.12.10
Bridge command 'MAC Address' filter value. If this object is included in the SNMP packet then the associated filter must be enabled in the bridge filter mask (bridgeCmdFilterMask).
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

eapsGroup 1.3.6.1.4.1.5504.4.7.13
OBJECT IDENTIFIER    

eapsConfigTable 1.3.6.1.4.1.5504.4.7.13.1
This table contains information required for the management of EAPS domains.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EapsConfigEntry

eapsConfigEntry 1.3.6.1.4.1.5504.4.7.13.1.1
An entry exists for each EAPS domain in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  EapsConfigEntry  

eapsConfigPrimaryPortLineGroup 1.3.6.1.4.1.5504.4.7.13.1.1.1
This object contains the line group IfIndex of the Primary EAPS Port.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  InterfaceIndex  

eapsConfigSecondaryPortLineGroup 1.3.6.1.4.1.5504.4.7.13.1.1.2
This object contains the line group IfIndex of the Secondary EAPS Port.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  InterfaceIndex  

eapsConfigControlVlan 1.3.6.1.4.1.5504.4.7.13.1.1.3
This object contains the VLAN ID of the control VLAN for this domain record. This is the VLAN ID used in EAPS control messages.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32 1..4090  

eapsConfigIsMasterNode 1.3.6.1.4.1.5504.4.7.13.1.1.4
If this value is True, then this record describes a Master Node. Otherwise, it describes a Transit Node.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

eapsConfigControlVlanPriority 1.3.6.1.4.1.5504.4.7.13.1.1.5
This object contains the Priority of the Control Vlan.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..7  

eapsConfigDomainName 1.3.6.1.4.1.5504.4.7.13.1.1.6
This object contains the user assigned ASCII representation of the Domain Name for this record. This name must be unique device wide.
Status: current Access: read-create
OBJECT-TYPE    
  ZhoneAdminString  

eapsConfigMsgTxInterval 1.3.6.1.4.1.5504.4.7.13.1.1.7
This object contains the interval, in seconds, that a node sends Health Messages on the ring.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

eapsConfigTimeout 1.3.6.1.4.1.5504.4.7.13.1.1.8
On a Master Node, this object contains the timeout, in seconds, which the Master Node will report a Ring Fault if it does not receive a Health Message on the ring. On a Transit Node, this is the pre-forwarding delay timeout (also in seconds).
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

eapsConfigMaxDroppedMessages 1.3.6.1.4.1.5504.4.7.13.1.1.9
On a Master Node, this object contains the number of contigious Health messages that may be dropped before the node declared a Ring Fault. This object is not used for a Transit node.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

eapsConfigSnmpTrap 1.3.6.1.4.1.5504.4.7.13.1.1.10
If this object is set to True, then this node will send SNMP Traps on Ring State transition.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

eapsConfigDomainEnable 1.3.6.1.4.1.5504.4.7.13.1.1.11
If this value is TRUE, the EAPS state machine will transition through the initialization process to the Health state. It will begin passing Control Messages and allow Protected VLAN data through the EAPS Domain. If this value is FALSE, the EAPS state machine will transition through the reset process to the Inactivate state. It will stop passing Control Messages and prohibit Protected VLAN data from being passed through the EAPS Domain.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

eapsConfigRowStatus 1.3.6.1.4.1.5504.4.7.13.1.1.12
This object is used to create and remove rows in the table. See eapsConfigEntry description for minimum requirements.
Status: current Access: read-create
OBJECT-TYPE    
  ZhoneRowStatus  

eapsProtectedVlanTable 1.3.6.1.4.1.5504.4.7.13.2
This table contains information required for the management of a list of protected VLAN's in an EAPS domains.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EapsProtectedVlanEntry

eapsProtectedVlanEntry 1.3.6.1.4.1.5504.4.7.13.2.1
An entry for each VLAN ranges that is to be protected in the EAPS domain.
Status: current Access: not-accessible
OBJECT-TYPE    
  EapsProtectedVlanEntry  

eapsProtectedVlanEntryIndex 1.3.6.1.4.1.5504.4.7.13.2.1.1
This object is an index which indicates which entry in the Protected Vlan Table is being addressed. For example, a value of 5 would indicate that the 5th entry (row) of this table is being addressed. This entry, along with eapsConfigPrimaryLineGroup, eapsConfigSecondaryLineGroup, and eapsConfigControlVlan indices select which Protected Vlan Table entry for a given eaps-domain-record profile. The first three indices select the profile, this last index selects the N'th entry in that profile
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Integer32 0..9  

eapsProtectedVlanLowerRange 1.3.6.1.4.1.5504.4.7.13.2.1.2
The eapsProtectedVlanLowerRange and eapsProtectedVlanUpperRange objects work in conjunction with one another to set the range of the protected vlans. If eapsProtectedVlanLowerRange is 0, then this indicates end of list. If eapsProtectedVlanLowerRange is not 0, but eapsProtectedVlanUpperRange is 0, then this would be have the same effect as both object having the same value and protect a single vlan ID. If they are both different and non-zero, then it specifies an inclusive range. Note that eapsProtectedVlanLowerRange must be numerically lower than eapsProtectedVlanUpperRange.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4090  

eapsProtectedVlanUpperRange 1.3.6.1.4.1.5504.4.7.13.2.1.3
The eapsProtectedVlanLowerRange and eapsProtectedVlanUpperRange objects work in conjunction with one another to set the range of the protected vlans. If eapsProtectedVlanLowerRange is 0, then this indicates end of list. If eapsProtectedVlanLowerRange is not 0, but eapsProtectedVlanUpperRange is 0, then this would be have the same effect as both object having the same value and protect a single vlan ID. If they are both different and non-zero, then it specifies an inclusive range. Note that eapsProtectedVlanLowerRange must be numerically lower than eapsProtectedVlanUpperRange.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..4090  

eapsProtectedVlanRowStatus 1.3.6.1.4.1.5504.4.7.13.2.1.4
This object is used to create and remove rows in the table. See eapsProtectedVlanEntry description for minimum requirements.
Status: current Access: read-create
OBJECT-TYPE    
  ZhoneRowStatus  

eapsProtectedVlanDomainName 1.3.6.1.4.1.5504.4.7.13.2.1.5
The domain name for the EAPS protected vlan entry.
Status: current Access: read-only
OBJECT-TYPE    
  ZhoneAdminString  

eapsStatusTable 1.3.6.1.4.1.5504.4.7.13.3
This table contains status of each EAPS domain state machine.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EapsStatusEntry

eapsStatusEntry 1.3.6.1.4.1.5504.4.7.13.3.1
The entry contains status of the domain's state machine.
Status: current Access: not-accessible
OBJECT-TYPE    
  EapsStatusEntry  

eapsPrevState 1.3.6.1.4.1.5504.4.7.13.3.1.1
Previous state for the domain.
Status: current Access: read-only
OBJECT-TYPE    
  EapsState  

eapsState 1.3.6.1.4.1.5504.4.7.13.3.1.2
Current state for the domain.
Status: current Access: read-only
OBJECT-TYPE    
  EapsState  

eapsStatsTable 1.3.6.1.4.1.5504.4.7.13.4
EAPS statistics table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EapsStatsEntry

eapsStatsEntry 1.3.6.1.4.1.5504.4.7.13.4.1
Displays the EAPS statistic table entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  EapsStatsEntry  

eapsStatsTotCtrlMsgSent 1.3.6.1.4.1.5504.4.7.13.4.1.1
Total EAPS control messages sent.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

eapsStatsTotCtrlMsgRecvd 1.3.6.1.4.1.5504.4.7.13.4.1.2
Total EAPS control messages received.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

eapsTrapPrefix 1.3.6.1.4.1.5504.4.7.13.5
Place-holder object for EAPS traps, which must have a final digit of 0 in OID.
Status: current Access: read-write
OBJECT-IDENTITY    

eapsTraps 1.3.6.1.4.1.5504.4.7.13.5.0
Traps raised by EAPS state machine.
Status: current Access: read-write
OBJECT-IDENTITY    

eapsStateChange 1.3.6.1.4.1.5504.4.7.13.5.0.1
State changed in the node for the EAPS domain.
Status: current Access: read-write
NOTIFICATION-TYPE    

eapsFailTimerExpFlagSet 1.3.6.1.4.1.5504.4.7.13.5.0.2
The eapsFailTimerExpFlagSet notification is generated when the EAPS domain's fail timer expires for the first time, while its state is not in Fail state.
Status: current Access: read-write
NOTIFICATION-TYPE    

eapsFailTimerExpFlagClear 1.3.6.1.4.1.5504.4.7.13.5.0.3
Description.
Status: current Access: read-write
NOTIFICATION-TYPE    

eapsLinkDownRingComplete 1.3.6.1.4.1.5504.4.7.13.5.0.4
If a transit is in Link-Down state, and it receives a Health-Check-Pdu from the Master indicating the ring is Complete, it means there is some problem with the Transit switch that has issued this trap message.
Status: current Access: read-write
NOTIFICATION-TYPE    

eapsTopologyTable 1.3.6.1.4.1.5504.4.7.13.6
EAPS topology table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EapsTopologyEntry

eapsTopologyEntry 1.3.6.1.4.1.5504.4.7.13.6.1
Displays the EAPS topology table entries.
Status: current Access: not-accessible
OBJECT-TYPE    
  EapsTopologyEntry  

eapsTopologyRing 1.3.6.1.4.1.5504.4.7.13.6.1.1
This represents the link as primary or secondary.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER primary(0), secondary(1)  

eapsTopologyRowNumber 1.3.6.1.4.1.5504.4.7.13.6.1.2
This represents the node number in the ring.
Status: current Access: not-accessible
OBJECT-TYPE    
  Integer32 0..47  

eapsTopologyDomainName 1.3.6.1.4.1.5504.4.7.13.6.1.3
This represents the domain name for this record.
Status: current Access: read-only
OBJECT-TYPE    
  ZhoneAdminString  

eapsTopologyMacAddr 1.3.6.1.4.1.5504.4.7.13.6.1.4
macAddress of the element in the ring.
Status: current Access: read-only
OBJECT-TYPE    
  MacAddress  

eapsTopologyIpAddr 1.3.6.1.4.1.5504.4.7.13.6.1.5
Ip addressed of the element in the ring.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

eapsTopologyType 1.3.6.1.4.1.5504.4.7.13.6.1.6
This represents whether the node is master or transit.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER master(0), transit(1)  

eapsTopologyPrimaryLinkName 1.3.6.1.4.1.5504.4.7.13.6.1.7
This represents the primary link name.
Status: current Access: read-only
OBJECT-TYPE    
  ZhoneAdminString  

eapsTopologyPrimaryLinkState 1.3.6.1.4.1.5504.4.7.13.6.1.8
This represents the primary link state.
Status: current Access: read-only
OBJECT-TYPE    
  EapsState  

eapsTopologySecondaryLinkName 1.3.6.1.4.1.5504.4.7.13.6.1.9
This represents the secondary link name.
Status: current Access: read-only
OBJECT-TYPE    
  ZhoneAdminString  

eapsTopologySecondaryLinkState 1.3.6.1.4.1.5504.4.7.13.6.1.10
This represents the secondary link state.
Status: current Access: read-only
OBJECT-TYPE    
  EapsState  

bridgeIgmpStatsTable 1.3.6.1.4.1.5504.4.7.14
The bridgeIgmpStatsTable is used to access the IGMP statistics for bridges.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BridgeIgmpStatsEntry

bridgeIgmpStatsEntry 1.3.6.1.4.1.5504.4.7.14.1
The bridgeIgmpStatsEntry holds IGMP stats for a bridge interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  BridgeIgmpStatsEntry  

genQueryRx 1.3.6.1.4.1.5504.4.7.14.1.1
general IGMP queries received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

genQueryTx 1.3.6.1.4.1.5504.4.7.14.1.2
general IGMP queries transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

specQueryRx 1.3.6.1.4.1.5504.4.7.14.1.3
Specific IGMP queries received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

specQueryTx 1.3.6.1.4.1.5504.4.7.14.1.4
Specific IGMP queries transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

v2ReportsRx 1.3.6.1.4.1.5504.4.7.14.1.5
Version 2 reports received (JOINs).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

v2ReportsTx 1.3.6.1.4.1.5504.4.7.14.1.6
Version 2 reports sent.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

leavesRx 1.3.6.1.4.1.5504.4.7.14.1.7
IGMP leaves received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

leavesTx 1.3.6.1.4.1.5504.4.7.14.1.8
IGMP leaves transmitted.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

unknownRx 1.3.6.1.4.1.5504.4.7.14.1.9
Unknown IGMP packets received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

errorRx 1.3.6.1.4.1.5504.4.7.14.1.10
IGMP packet is bad received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

actChans 1.3.6.1.4.1.5504.4.7.14.1.11
Number of active muticast channels.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

actHosts 1.3.6.1.4.1.5504.4.7.14.1.12
Number of active multicast hosts.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

v3GenQueryRx 1.3.6.1.4.1.5504.4.7.14.1.13
Number of IGMP V3 Queries received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

v3GenQueryTx 1.3.6.1.4.1.5504.4.7.14.1.14
Number of IGMP V3 queries sent.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

v3SpecQueryRx 1.3.6.1.4.1.5504.4.7.14.1.15
Number of IGMP V3 specific queries received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

v3SpecQueryTx 1.3.6.1.4.1.5504.4.7.14.1.16
Number of IGMP V3 specific queries sent.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

v3ReportsRx 1.3.6.1.4.1.5504.4.7.14.1.17
Number of IGMP V3 reports received.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

v3ReportsTx 1.3.6.1.4.1.5504.4.7.14.1.18
Number of IGMP V3 reports sent.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

bridgeGroup 1.3.6.1.4.1.5504.4.7.15
OBJECT IDENTIFIER    

bridgeTrapPrefix 1.3.6.1.4.1.5504.4.7.15.1
Traps raised for bridge conditions.
Status: current Access: read-only
OBJECT-IDENTITY    

bridgeTraps 1.3.6.1.4.1.5504.4.7.15.1.0
Bridge traps go under here - extra layer needed to ensure '0' in OID.
Status: current Access: read-only
OBJECT-IDENTITY    

bridgeLoopDetection 1.3.6.1.4.1.5504.4.7.15.1.0.1
Trap when bridge is looping on flap.
Status: current Access: read-only
NOTIFICATION-TYPE    

bridgeStormDetection 1.3.6.1.4.1.5504.4.7.15.1.0.2
Trap sent when a bridge packet storm is detected.
Status: current Access: read-only
NOTIFICATION-TYPE    

bridgeTrapObjects 1.3.6.1.4.1.5504.4.7.16
OBJECT IDENTIFIER    

bridgeMacAddrString 1.3.6.1.4.1.5504.4.7.16.1
vlan/slan/macAddress for bridge
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  OCTET STRING  

bridgeIgmpTable 1.3.6.1.4.1.5504.4.7.17
The bridgeIgmpTable is used to access the IGMP data for bridges for when IGMP is in proxy mode and the IGMP status must be obtained from the linecard.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BridgeIgmpEntry

bridgeIgmpEntry 1.3.6.1.4.1.5504.4.7.17.1
BridgeIgmpEntry contains the igmp multicast data information for a bridge, indexed by ifIndex, hostMac, and mcastMac.
Status: current Access: not-accessible
OBJECT-TYPE    
  BridgeIgmpEntry  

slanId 1.3.6.1.4.1.5504.4.7.17.1.1
IGMP slan identifier. Maximum value 4090 as defined by MAX_VLAN_NUM.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4090  

vlanId 1.3.6.1.4.1.5504.4.7.17.1.2
IGMP vlan identifier. Maximum value 4090 as defined my MAX_VLAN_NUM
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..4090  

mcastMac 1.3.6.1.4.1.5504.4.7.17.1.3
IGMP Multicast MAC addressed to bridge port.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..6)  

mcastIP 1.3.6.1.4.1.5504.4.7.17.1.4
IGMP Multicast IP addressed to bridge port.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

hostMac 1.3.6.1.4.1.5504.4.7.17.1.5
MAC address of end device receiving multicast packets.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..6)  

lastJoinTimer 1.3.6.1.4.1.5504.4.7.17.1.6
Count down timer before IGMP entry ages out.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

staticBridgePathTable 1.3.6.1.4.1.5504.4.7.18
A collection of staticBridgePathEntries. The StaticBridgePath OID has the following format: OID psn MAC entries IPv4 entries IPv6 entries ---------- ------------- -------------- -------------- tlist[0] ifIndex ifIndex ifIndex tlist[1] address type address type address type tlist[2] vlan vlan vlan tlist[3] macAddr[0] IPv4[0] IPv6[0] tlist[4] macAddr[1] IPv4[1] IPv6[1] tlist[5] macAddr[2] IPv4[2] IPv6[2] tlist[6] macAddr[3] IPv4[3] IPv6[3] tlist[7] macAddr[4] zero IPv6[4] tlist[8] macAddr[5] zero IPv6[5] tlist[9] zero zero IPv6[6] tlist[10] zero zero IPv6[7] tlist[11] zero zero IPv6[8] tlist[12] zero zero IPv6[9] tlist[13] zero zero IPv6[10] tlist[14] zero zero IPv6[11] tlist[15] zero zero IPv6[12] tlist[16] zero zero IPv6[13] tlist[17] zero zero IPv6[14] tlist[18] zero zero IPv6[15] tlist[19] slan slan slan
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    StaticBridgePathEntry

staticBridgePathEntry 1.3.6.1.4.1.5504.4.7.18.1
Static Path Bridge entries are created by the user in order to specify forwarding for a particular interface, vlanId, mac address or ip address, slanId (for QinQ). The INDEX value for staticBridgePathEntry consists of following 5 values: ifIndex staticBridgePathAddressType bridgeIfVlanId staticBridgePathMacOrIpAddress bridgeIfStagId If staticBridgeAddressType is set to macAddr(1), then staticBridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress are used for the bridge path. If staticBridgeAddressType is set to ipAddr(2), then staticBridgeMacOrIpAddress represents an IP Address, and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress are used for the bridge path. If staticBridgeAddressType is set to vlanIdAddr(3), then ifIndex and bridgeIfVlanId are used for the bridge path. If staticBridgeAddressType is set to globalAddr(4), then ifIndex is used for the bridge path.
Status: current Access: not-accessible
OBJECT-TYPE    
  StaticBridgePathEntry  

staticBridgePathMacOrIpAddress 1.3.6.1.4.1.5504.4.7.18.1.1
If the staticBridgeAddressType is set to macAddr(1), then this field represents a MAC address. If the staticBridgeAddressType is set to ipAddr(2), then this field represents an IP address. The IP address can be four octets ( for IPv4 ) or sixteen octets ( for IPv6 ).
Status: current Access: not-accessible
OBJECT-TYPE    
  NetworkAddress  

staticBridgePathAddressType 1.3.6.1.4.1.5504.4.7.18.1.2
If staticBridgeIPv6AddressType is set to macAddr(1), then staticBridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress are used for the bridge path. If staticBridgeIPv6AddressType is set to ipAddr(2), then staticBridgeMacOrIpAddress represents an IP Address, and ifIndex, bridgeIfVlanId and staticBridgeMacOrIpAddress are used for the bridge path. If staticBridgeIPv6AddressType is set to vlanIdAddr(3) or intralinkAddr(7), then ifIndex and bridgeIfVlanId are used for the bridge path. If staticBridgeIPv6AddressType is set to globalAddr(4), globalIntralinkAddr(8), or mvrAddr(13) then ifIndex is used for the bridge path. If staticBridgeIPv6AddressType is set to dhcpAllowOui( 720901) then the first 3 bytes of the MAC address contains the OUI that we will allow DHCP addresses to be granted to, global scope. If staticBridgeIPv6AddressType is set to dhcpIpAddr(9), or to dhcpMacAddr(10), then the other fields are populated as for address types ipAddr and macAddr respectively, with the difference that these are secure entries, learned by snooping DHCP. If staticBridgeIPv6AddressType is set to vlanParms(14), then the static bridge entry holds parameters for the given VLAN and SLAN ID (for example, flap mode, unicast aging period, etc) and is not associated with any specific bridge, but with all bridges with the same VLAN/SLAN ID. For this reason, the IfIndex of this entry must be zero. If staticBridgeIPv6AddressType is set to secMvrAddr(15), then the static bridge entry holds parameters for a Secondary MVR path. The VLAN ID of this entry is the Secondary VLAN ID. If staticBridgeIPv6AddressType is set to ipAddrV6(16), then staticBridgeMacOrIpAddress represents an IPv6 Address, and ifIndex, bridgeIfVlanId and staticBridgeIPv6MacOrIpAddress are used for the bridge path. If staticBridgeIPv6AddressType is set to dhcpIpAddrV6(17), or to dhcpMacAddr(10), then the other fields are populated as for address types ipAddr and macAddr respectively, with the difference that these are secure entries, learned by snooping DHCP.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER macAddr(1), ipAddr(2), vlanIdAddr(3), globalAddr(4), intralinkAddr(7), globalIntralinkAddr(8), dhcpIpAddr(9), dhcpMacAddr(10), mvrAddr(13), vlanParms(14), secMvrAddr(15), ipAddrV6(16), dhcpIpAddrV6(17), dhcpAllowOui(720901)  

staticBridgePathMulticastAging 1.3.6.1.4.1.5504.4.7.18.1.3
Multicast Aging period in tenths of seconds for the specified VLAN. After the specified aging period is met, the VLAN address is deleted from the routing table. A value of 0 indicates that aging is turned off. Maximum value is 2147483647 tenths of seconds, which equates to approximately 2485.51 days.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..2147483647  

staticBridgePathRowStatus 1.3.6.1.4.1.5504.4.7.18.1.4
Used to create, modify or delete an entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  ZhoneRowStatus  

staticBridgePathFlapControl 1.3.6.1.4.1.5504.4.7.18.1.5
This object enables or disable Flap Control in the Bridge Filter Table. The value 'disable(2)' turns Flap Control mode off. The values 'enable(3)' or 'fast(4) turn flap control mode on. 'Enable(3)' applies a hold time of 60 secs before allowing addr/IP to be moved to a new port, while 'fast(4)' applies a hold time of 0 secs. A value of 'default(1)' indicates 'Don't Care' and defaults to a disable or enable set by another entry.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER default(1), disable(2), enable(3), fast(4)  

staticBridgePathUnicastAging 1.3.6.1.4.1.5504.4.7.18.1.6
Multicast Aging period in tenths of seconds for the specified VLAN. After the specified aging period is met, the VLAN address is deleted from the routing table. A value of 0 indicates that aging is turned off. Maximum value is 2147483647 tenths of seconds, which equates to approximately 2485.51 days.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0 | 120..2147483647  

staticBridgePathIgmpQueryInterval 1.3.6.1.4.1.5504.4.7.18.1.7
How often (in seconds) we as a bridge inject IGMP query values into the stream.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32  

staticBridgePathFlags 1.3.6.1.4.1.5504.4.7.18.1.8
none : IGMP Snooping with Proxy reporting is disabled. BIT 0(igmpProcessJoinAndLeave) : igmpProcessJoinandLeave is enabled for IGMP packets. BIT 1(igmpRespondToQuery) : igmpRespondToQuery is enabled for IGMP packets. BIT 2(igmpUseBridgeIpAddress) : igmpUseBridgeIpAddress is enabled for IGMP packets.
Status: current Access: read-create
OBJECT-TYPE    
  BITS igmpProcessJoinAndLeave(0), igmpRespondToQuery(1), igmpUseBridgeIpAddress(2)  

staticBridgePathIgmpCustomIpAddress 1.3.6.1.4.1.5504.4.7.18.1.9
Allow the configuration of the source IP address for packets that we originate upstream when doing IGMP Porxy on a bridge.
Status: current Access: read-create
OBJECT-TYPE    
  IpAddress  

staticBridgePathLoopPrevention 1.3.6.1.4.1.5504.4.7.18.1.10
This field does the following options,'BlockAsym(1)' blocks a learning bridge if flap is detected between it and an uplink bridge. 'BlockAll(2)' incorporates 'blockAsym(1)' but it also blocks a learning bridge if it flaps against another learning bridge.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), blockAsym(1), blockAll(2), blockAsymAuto(3), blockAllAuto(4)  

staticBridgePathIgmpDscp 1.3.6.1.4.1.5504.4.7.18.1.11
This parameter indicates DSCP value for igmp traffic. Valid code values: <0-63> Differentiated services codepoint value af11 Mark packets with AF11 dscp (001010) af12 Mark packets with AF12 dscp (001100) af13 Mark packets with AF13 dscp (001110) af21 Mark packets with AF21 dscp (010010) af22 Mark packets with AF22 dscp (010100) af23 Mark packets with AF23 dscp (010110) af31 Mark packets with AF31 dscp (011010) af32 Mark packets with AF32 dscp (011100) af33 Mark packets with AF33 dscp (011110) af41 Mark packets with AF41 dscp (100010) af42 Mark packets with AF42 dscp (100100) af43 Mark packets with AF43 dscp (100110) cs1 Mark packets with CS1(precedence 1) dscp (001000) cs2 Mark packets with CS2(precedence 2) dscp (010000) cs3 Mark packets with CS3(precedence 3) dscp (011000) cs4 Mark packets with CS4(precedence 4) dscp (100000) cs5 Mark packets with CS5(precedence 5) dscp (101000) cs6 Mark packets with CS6(precedence 6) dscp (110000) cs7 Mark packets with CS7(precedence 7) dscp (111000) default Mark packets with default dscp (000000) ef Mark packets with EF dscp (101110)
Status: current Access: read-create
OBJECT-TYPE    
  OCTET STRING Size(1..8)  

bridgePathIfLookupTable 1.3.6.1.4.1.5504.4.7.19
A collection of bridgePathIfLookupTable entries. The bridgePathIfLookup OID has the following format: OID psn MAC entries IPv4 entries IPv6 entries ---------- ------------- -------------- -------------- tlist[0] address type address type address type tlist[1] macAddr[0] IPv4[0] IPv6[0] tlist[2] macAddr[1] IPv4[1] IPv6[1] tlist[3] macAddr[2] IPv4[2] IPv6[2] tlist[4] macAddr[3] IPv4[3] IPv6[3] tlist[5] macAddr[4] zero IPv6[4] tlist[6] macAddr[5] zero IPv6[5] tlist[7] zero zero IPv6[6] tlist[8] zero zero IPv6[7] tlist[9] zero zero IPv6[8] tlist[10] zero zero IPv6[9] tlist[11] zero zero IPv6[10] tlist[12] zero zero IPv6[11] tlist[13] zero zero IPv6[12] tlist[14] zero zero IPv6[13] tlist[15] zero zero IPv6[14] tlist[16] zero zero IPv6[15] tlist[17] vlan vlan vlan tlist[18] ifIndex ifIndex ifIndex tlist[19] slan slan slan
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BridgePathIfLookupEntry

bridgePathIfLookupEntry 1.3.6.1.4.1.5504.4.7.19.1
Bridge IfLookup entries are created by the user or learned by the software in order to specify forwarding for a particular interface, vlanId/slanId, mac address or ip address. The INDEX value for bridgeIfLookupEntry consists of following 5 values: bridgeIfAddressType bridgeIfMacOrIpAddress bridgeIfVlanId ifIndex bridgeIfStagId If bridgeIfAddressType is set to unicast_mac(1), then bridgeIfMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId/Slanid and bridgeIfMacOrIpAddress are use for the bridge path. If bridgeIfAddressType is set to multicast_mac(2), then bridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId/SlanId and bridgeIfMacOrIpAddress are used for bridge path. If bridgeIfAddressType is set to ip_address(3), then ifIndex and bridgeIfVlanId/SlanId are used for the bridge path.
Status: current Access: not-accessible
OBJECT-TYPE    
  BridgePathIfLookupEntry  

bridgePathIfAddressType 1.3.6.1.4.1.5504.4.7.19.1.1
If bridgeIfAddressType is set to unicast_mac(1), then bridgeIfMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and bridgeIfMacOrIpAddress are used for the bridge path. If bridgeIfAddressType is set to multicast_mac(2), then bridgeMacOrIpAddress represents a MAC Address, and ifIndex, bridgeIfVlanId and bridgeIfMacOrIpAddress are used for the bridge path. If bridgeIfAddressType is set to ip_address(3), then ifIndex and bridgeIfVlanId are used for the bridge path. If bridgeIfAddressType is set to dhcp_mac(4), or dhcp_ip(5), then the address is as desribed for types 1 and 3, respectively, and the address was learned by snooping DHCP packets.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER unicastMac(1), multicastMac(2), ipAddress(3), dhcpMac(4), dhcpIp(5)  

bridgePathIfMacOrIpAddress 1.3.6.1.4.1.5504.4.7.19.1.2
If bridgeIfAddressType is set to FILTER_ENTRY_UNICAST_MAC(1) or to FILTER_ENTRY_MULTICAST_MAC(2), or to FILTER_ENTRY_DHCP_MAC(4), then bridgeIfMacOrIpAddress represents a MAC Address. If bridgeIfAddressType is set to FILTER_ENTRY_IP_ADDRESS(3), or to FILTER_ENTRY_DHCP_IP(5), then bridgeIfMacOrIpAddress represents an IP Address.
Status: current Access: not-accessible
OBJECT-TYPE    
  NetworkAddress  

bridgePathIfLookupStaticOrDynamic 1.3.6.1.4.1.5504.4.7.19.1.3
If bridgeIfLookupStaticOrDynamic is set to 1, then this table entry is static and persistent. If bridgeIfLookupStaticOrDynamic is set to 2, then this table entry is learned and is not persistent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER staticEntry(1), dynamicEntry(2)  

bridgePathIfLookupFlush 1.3.6.1.4.1.5504.4.7.19.1.4
The object 'bridgeIfLookupFlush' allows a user to flush learned entries in the bridgeFilterTable when the ifIndex of the entry is not known. A combination of address type, MAC or IP address and vlan ID is used to determine the ifIndex of the entry to be removed. Setting the object to 'true' causes the flush action to occur. After the flush action is taken, the value of bridgeIfLookupFlush is immediately set back to 'false'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

bridgePathAddressLookupTable 1.3.6.1.4.1.5504.4.7.20
A collection of bridgePathAddressLookupTable entries. The bridgePathAddressLookup OID has the following format: OID psn MAC entries IPv4 entries IPv6 entries ---------- ------------- -------------- -------------- tlist[0] ifIndex ifIndex ifIndex tlist[1] address type address type address type tlist[2] macAddr[0] IPv4[0] IPv6[0] tlist[3] macAddr[1] IPv4[1] IPv6[1] tlist[4] macAddr[2] IPv4[2] IPv6[2] tlist[5] macAddr[3] IPv4[3] IPv6[3] tlist[6] macAddr[4] zero IPv6[4] tlist[7] macAddr[5] zero IPv6[5] tlist[8] zero zero IPv6[6] tlist[9] zero zero IPv6[7] tlist[10] zero zero IPv6[8] tlist[11] zero zero IPv6[9] tlist[12] zero zero IPv6[10] tlist[13] zero zero IPv6[11] tlist[14] zero zero IPv6[12] tlist[15] zero zero IPv6[13] tlist[16] zero zero IPv6[14] tlist[17] zero zero IPv6[15] tlist[18] vlan vlan vlan tlist[19] slan slan slan
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BridgePathAddressLookupEntry

bridgePathAddressLookupEntry 1.3.6.1.4.1.5504.4.7.20.1
BridgePathAddressLookup entries are created by the user or learned by the software in order to specify forwarding for a particular interface, vlanId/slanId, mac address or ip address. The INDEX value for bridgePathLookupEntry consists of following 5 values: ifIndex bridgeIfAddressType bridgeIfMacOrIpAddress bridgeIfVlanId bridgeIfStagId
Status: current Access: not-accessible
OBJECT-TYPE    
  BridgePathAddressLookupEntry  

bridgePathAddressLookupStaticOrDynamic 1.3.6.1.4.1.5504.4.7.20.1.1
If bridgePathAddressLookupStaticOrDynamic is set to 1, then this table entry is static and persistent. If bridgePathAddressLookupStaticOrDynamic is set to 2, then this table entry is learned and is not persistent.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER staticEntry(1), dynamicEntry(2)  

bridgePathAddressLookupFlush 1.3.6.1.4.1.5504.4.7.20.1.2
The object 'bridgePathAddressFlush' allows a user to flush learned entries in the bridgeFilterTable when the ifIndex of the entry is known. The ifIndex is used to determine which interface is to be removed. Setting the object to 'true' causes the flush action to occur. After the flush action is taken, the value of bridgePathLookupFlush is immediately set back to 'false'.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

bridgeStatusTable 1.3.6.1.4.1.5504.4.7.21
This table contains runtime status for each bridge interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    BridgeStatusEntry

bridgeStatusEntry 1.3.6.1.4.1.5504.4.7.21.1
Runtime status data for a single bridge.
Status: current Access: not-accessible
OBJECT-TYPE    
  BridgeStatusEntry  

bridgeStatusState 1.3.6.1.4.1.5504.4.7.21.1.1
Values: up(1), UP down(2), DWN trouble(3), TRB notAvailable(4), NA initializing(5), INI adminDown(6), ADN adminStateTest(7), TST adminStateNone(8), N/S ready(9), RDY discovering(10), DSC unknown(11), ??? blocked(12), BLK pending(13), PND disabled(14), DIS learning(15), LRN forwarding(16), FWD blockedFlapping(17), BLF blockedPersistent(18), BLP blockedFlappingPersistenr(19), BFP
Status: current Access: read-only
OBJECT-TYPE    
  BridgeState  

zhoneCompliances 1.3.6.1.4.1.5504.9
OBJECT IDENTIFIER    

zhoneGroups 1.3.6.1.4.1.5504.9.1
OBJECT IDENTIFIER    

zhoneBridgeGroup 1.3.6.1.4.1.5504.9.1.23
The list of zhone bridge objects.
Status: current Access: read-only
OBJECT-GROUP    

zhoneBridgeCmdGroup 1.3.6.1.4.1.5504.9.1.76
Bridge CMD objects
Status: current Access: read-only
OBJECT-GROUP    

zhoneBridgeEapsGroup 1.3.6.1.4.1.5504.9.1.77
EAPS objects
Status: current Access: read-only
OBJECT-GROUP    

zhoneBridgeEapsConfigGroup 1.3.6.1.4.1.5504.9.1.78
EAPS config objects
Status: current Access: read-only
OBJECT-GROUP    

zhoneBridgeEapsTopologyGroup 1.3.6.1.4.1.5504.9.1.79
EAPS Topology objects
Status: current Access: read-only
OBJECT-GROUP    

zhoneBridgeNotificationGroup 1.3.6.1.4.1.5504.9.1.80
BRIDGE Notifications
Status: current Access: read-only
NOTIFICATION-GROUP    

zhoneBridgeIgmpGroup 1.3.6.1.4.1.5504.9.1.81
IGMP objects
Status: current Access: read-only
OBJECT-GROUP    

zhoneBridgeStatsGroup 1.3.6.1.4.1.5504.9.1.82
Bridge STATS objects
Status: current Access: read-only
OBJECT-GROUP