ZHNSYSTEM

File: ZHNSYSTEM.mib (80304 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-CONF	SNMPv2-TC
Zhone	Zhone-TC

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	enterprises
Integer32	Unsigned32	IpAddress
MODULE-COMPLIANCE	OBJECT-GROUP	TEXTUAL-CONVENTION
DisplayString	MacAddress	RowStatus
TruthValue	zhoneWtn	ZhoneRowStatus

Defined Types

WFNT
The Wifi Network Type
TEXTUAL-CONVENTION
	INTEGER	notApplicable(0), baseStation(1), mesh(2)

ELTYPE
Ethernet Like Interface Type
TEXTUAL-CONVENTION
	INTEGER	ethernet(1), efm(2), shdsl(3), docsis(4), wimax(5)

ELSUBTYPE
Ethernet Like Interface Sub-Type
TEXTUAL-CONVENTION
	INTEGER	none(0)

LPT
Line Power Direction
TEXTUAL-CONVENTION
	INTEGER	none(0), in(1), out(2)

UPT
Unit Power Supply Type
TEXTUAL-CONVENTION
	INTEGER	ac(1), dc(2)

TCSI
Transmit Clock Source Items
TEXTUAL-CONVENTION
	INTEGER	notApplicable(0), loop(1), local(2), pwe(3)

LTRI
Local Timing Reference Items
TEXTUAL-CONVENTION
	INTEGER	notApplicable(0), ethernet(1), internal(2), shdsl(3)

CSMI
Pseudo Wire Clock Synchronization Mode Items
TEXTUAL-CONVENTION
	INTEGER	notApplicable(0), adaptive(1), differential(2), synchronous(3), dslAdaptive(4), loop(5)

SEI
Synchronous Ethernet Items
TEXTUAL-CONVENTION
	INTEGER	enable(1), disable(2)

CMI
Clock Mode Items
TEXTUAL-CONVENTION
	INTEGER	notApplicable(0), normal(1), differential(2)

CDA
Configuration Database Action
TEXTUAL-CONVENTION
	INTEGER	noAction(0), save(1), resetToDefaults(2)

RBT
Software Reboot Action
TEXTUAL-CONVENTION
	INTEGER	noAction(0), reboot(1)

SCS
System Clock Source Items
TEXTUAL-CONVENTION
	INTEGER	notApplicable(0), uplink(1), ds1(2), ieee1588(3)

ETCS
Ethernet Transmit Clock Source Items
TEXTUAL-CONVENTION
	INTEGER	notApplicable(0), internal(1), systemClock(2)

SysFirmwareAction
Action to take on the current firmware version.
TEXTUAL-CONVENTION
	INTEGER	noAction(0), restoreAltFirmware(1)

SysAdminStatus
Administrative status options for various system services, like syslog and power-shedding.
TEXTUAL-CONVENTION
	INTEGER	enable(1), disable(2)

SysLogLevel
SysLog logging level options, per RFC 3164.
TEXTUAL-CONVENTION
	INTEGER	emergency(0), alert(1), critical(2), error(3), warning(4), notice(5), informational(6), debug(7)

SysLogMode
SysLog logging mode of operation.
TEXTUAL-CONVENTION
	INTEGER	local(1), remote(2), both(3)

SysSntpTimeZones
Simple Network Timing Protocol time zones.
TEXTUAL-CONVENTION
	INTEGER	unknown(0), abu(1), adelaide(2), alaska(3), almaty(4), amsterdam(5), arizona(6), astana(7), athens(8), atlantic(9), auckland(10), azores(11), baghdad(12), baku(13), bangkok(14), beijing(15), belgrade(16), bogota(17), brasilia(18), brisbane(19), brussels(20), bucharest(21), buenos(22), cairo(23), canberra(24), cape(25), caracas(26), casablanca(27), central(28), centraltime(29), chennai(30), chihuahua(31), darwin(32), eastern(33), ekaterinburg(34), fiji(35), greenland(36), greenwich(37), guadalajara(38), guam(39), harare(40), hawaii(41), helsinki(42), hobart(43), indiana(44), international(45), irkutsk(46), islamabad(47), jerusalem(48), kabul(49), kathmandu(50), krasnoyarsk(51), kuala(52), kuwait(53), magadan(54), midatlantic(55), midway(56), moscow(57), mountain(58), nairobi(59), newfoundland(60), osaka(61), pacific(62), perth(63), rangoon(64), santiago(65), sarajevo(66), saskatchewan(67), seoul(68), solomon(69), sri(70), taipei(71), tehran(72), vladivostok(73), west(74), yakutsk(75)

IPInterfaceAddressingTypeValues
The addressing method used to assign the LAN-side IP Address. Enumeration of: Unknown Unconfigured Default DHCP Static PPPoE OMCI
TEXTUAL-CONVENTION
	OCTET STRING	Size(0..32)

BasicAddressingTypeValues
Enumeration of: DHCP - The DNS information is obtained via DHCP Static - The DNS information is manually provisioned
TEXTUAL-CONVENTION
	OCTET STRING	Size(0..16)

BoardDescriptorEntry
SEQUENCE
	boardIndex	Unsigned32
	boardName	DisplayString
	boardPartNumber	DisplayString
	boardSerialNumber	DisplayString
	boardRevision	DisplayString

PldDescriptorEntry
SEQUENCE
	pldIndex	Unsigned32
	pldName	DisplayString
	pldVersion	DisplayString

EthernetlikeInterfaceEntry
SEQUENCE
	etherIndex	Unsigned32
	etherName	DisplayString
	etherType	ELTYPE
	etherSubtype	ELSUBTYPE
	etherNumberOfPorts	Unsigned32
	etherLinePower	LPT
	etherPowerPairs	Integer32

TemperatureSensorEntry
SEQUENCE
	temperatureSensorIndex	Unsigned32
	temperatureSensorName	DisplayString
	temperatureSensorMaximum	DisplayString
	temperatureSensorMinimum	DisplayString

ZhnCommunityTableEntry
SEQUENCE
	communityName	DisplayString
	communityType	INTEGER
	communityRowStatus	RowStatus

ZhnTrapManagerInfoTableEntry
SEQUENCE
	trapDestination	IpAddress
	trapCommunityName	DisplayString
	trapVersion	INTEGER
	trapPort	INTEGER
	trapRowStatus	RowStatus

ZhnFixedCommunityTableEntry
SEQUENCE
	fixedCommunityName	DisplayString
	fixedCommunityType	INTEGER
	fixedCommunityRowStatus	RowStatus

ZhnDnsProxyHostEntry
SEQUENCE
	dnsProxyHostIndex	Unsigned32
	dnsProxyHostIPAddress	IpAddress
	dnsProxyHostName	OCTET STRING
	dnsProxyRowStatus	ZhoneRowStatus

Defined Values

zhnSystem		1.3.6.1.4.1.5504.2.5.2
This file defines the private Enterprise MIB extensions that define system related objects. ============================================================== == == == Copyright (C) 2008-2012 Zhone Technologies, Inc. == == == ==============================================================
MODULE-IDENTITY

zhnSystemObjects		1.3.6.1.4.1.5504.2.5.2.1
OBJECT IDENTIFIER

zhnSystemGeneralObjects		1.3.6.1.4.1.5504.2.5.2.1.1
OBJECT IDENTIFIER

zhnSystemBoardObjects		1.3.6.1.4.1.5504.2.5.2.1.2
OBJECT IDENTIFIER

zhnSystemPldObjects		1.3.6.1.4.1.5504.2.5.2.1.3
OBJECT IDENTIFIER

zhnSystemRadioObjects		1.3.6.1.4.1.5504.2.5.2.1.4
OBJECT IDENTIFIER

zhnSystemEthernetLikeObjects		1.3.6.1.4.1.5504.2.5.2.1.5
OBJECT IDENTIFIER

zhnSystemTempSensorObjects		1.3.6.1.4.1.5504.2.5.2.1.6
OBJECT IDENTIFIER

zhnSystemSNMPObjects		1.3.6.1.4.1.5504.2.5.2.1.7
OBJECT IDENTIFIER

zhnSystemTrapObjects		1.3.6.1.4.1.5504.2.5.2.1.8
OBJECT IDENTIFIER

zhnSystemSyslogObjects		1.3.6.1.4.1.5504.2.5.2.1.9
OBJECT IDENTIFIER

zhnSystemSNTPObjects		1.3.6.1.4.1.5504.2.5.2.1.10
OBJECT IDENTIFIER

zhnSystemUserLoginObjects		1.3.6.1.4.1.5504.2.5.2.1.11
OBJECT IDENTIFIER

zhnSystemPowerSheddingObjects		1.3.6.1.4.1.5504.2.5.2.1.12
OBJECT IDENTIFIER

zhnSystemFirewallObjects		1.3.6.1.4.1.5504.2.5.2.1.13
OBJECT IDENTIFIER

zhnSystemDNSClientObjects		1.3.6.1.4.1.5504.2.5.2.1.14
OBJECT IDENTIFIER

zhnSystemDNSProxyObjects		1.3.6.1.4.1.5504.2.5.2.1.15
OBJECT IDENTIFIER

zhnSystemWanBackupObjects		1.3.6.1.4.1.5504.2.5.2.1.16
OBJECT IDENTIFIER

zhnSystemTr69cObjects		1.3.6.1.4.1.5504.2.5.2.1.17
OBJECT IDENTIFIER

modelNumber		1.3.6.1.4.1.5504.2.5.2.1.1.1
model no. of the device
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

macBaseAddress		1.3.6.1.4.1.5504.2.5.2.1.1.2
First MAC Address in series
Status: current	Access: read-only
OBJECT-TYPE
	MacAddress

numberOfMacAddresses		1.3.6.1.4.1.5504.2.5.2.1.1.3
Number of MAC Address sequentially defined in the Unit starting at the MAC Base Address.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..10

wifiNetworkType		1.3.6.1.4.1.5504.2.5.2.1.1.4
Defines the Network Type or Mode of the Unit, i.e. Mesh or Base Station
Status: current	Access: read-write
OBJECT-TYPE
	WFNT

locationLatitude		1.3.6.1.4.1.5504.2.5.2.1.1.6
The latitude of the unit's location represented in degrees decimal. The format of the location's latitude is: [+ | -]ddd.dddddddd where + indicates north - indicates south d is a decimal digit (0 <= d <= 9) Valid range is -90 to +90 degrees.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

locationLongitude		1.3.6.1.4.1.5504.2.5.2.1.1.7
The longitude of the unit's location represented in degrees decimal. The format of the location's longitude is: [+ | -]ddd.dddddddd where + indicates east - indicates west d is a decimal digit (0 <= d <= 9) Valid range is -180 to +180 degrees.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

zhnSystemAction		1.3.6.1.4.1.5504.2.5.2.1.1.8
Action parameter to handle the action on other scalars.
Status: current	Access: read-write
OBJECT-TYPE
	RowStatus

zhnSysLocation		1.3.6.1.4.1.5504.2.5.2.1.1.9
System location. This object is synonomous with the MIB II system sysLocation object.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

zhnSysContact		1.3.6.1.4.1.5504.2.5.2.1.1.10
System contact. This object is synonomous with the MIB II system sysContact object.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sysTransmitClockSource		1.3.6.1.4.1.5504.2.5.2.1.1.11
T1 Clock source for PWE device. Since both T1/E1 interfaces will be required to have the same source, this object will replace the dsx1TransmitClockSource object in the DS1-MIB. This object is not supported by ZNID devices.
Status: current	Access: read-write
OBJECT-TYPE
	TCSI

sysLocalTimingReference		1.3.6.1.4.1.5504.2.5.2.1.1.12
Source of the sysTransmitClockSource when set to Local. This object is not supported by ZNID devices.
Status: current	Access: read-write
OBJECT-TYPE
	LTRI

sysSynchronizationMode		1.3.6.1.4.1.5504.2.5.2.1.1.13
Determines the method of ensuring Service Clock synchronization between the Source and Remote PWE devices.
Status: current	Access: read-write
OBJECT-TYPE
	CSMI

sysSynchronousEthernet		1.3.6.1.4.1.5504.2.5.2.1.1.14
Determines whether or not to use the 25MHz clock derived from the Synchronous Ethernet Port. This object is not supported by ZNID devices.
Status: current	Access: read-write
OBJECT-TYPE
	SEI

sysClockMode		1.3.6.1.4.1.5504.2.5.2.1.1.15
Determines the mode for which the PWE chip will be initialized.
Status: current	Access: read-write
OBJECT-TYPE
	CMI

sysCfgDBAction		1.3.6.1.4.1.5504.2.5.2.1.1.16
Perform an action on the configuration database.
Status: current	Access: read-write
OBJECT-TYPE
	CDA

sysSoftwareReboot		1.3.6.1.4.1.5504.2.5.2.1.1.17
Perform a software reboot.
Status: current	Access: read-write
OBJECT-TYPE
	RBT

sysSystemClockSource		1.3.6.1.4.1.5504.2.5.2.1.1.18
Determines the system-level clock mode for ZNID devices. uplink - the system will recover its clock from the configured uplink (e.g. GPON, SPF1, SFP2, etc.). ds1 - the system will recover its clock from the configured sysDs1ClockSourcePort. ieee1588 - the system will recover clock from the on-board 1588 clock circuitry.
Status: current	Access: read-write
OBJECT-TYPE
	SCS

sysEthernetTransmitClockSource		1.3.6.1.4.1.5504.2.5.2.1.1.19
Determines the transmit clock source for all ethernet ports requiring a clock. internal - all ethernet ports will recover clock from the local oscillator. systemClock - all ethernet ports will recover clock from the sysSystemClockSource.
Status: current	Access: read-write
OBJECT-TYPE
	ETCS

sysDs1ClockSourcePort		1.3.6.1.4.1.5504.2.5.2.1.1.20
The interface name for the DS1 port providing transmit clock when the sysSystemClockSource is set to ds1.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

sysBootloaderVersion		1.3.6.1.4.1.5504.2.5.2.1.1.21
System bootloader (CFE) firmware version.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1..64)

sysFirmwareVersion		1.3.6.1.4.1.5504.2.5.2.1.1.22
The version of firmware the system is currently running.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1..64)

sysAltFirmwareVersion		1.3.6.1.4.1.5504.2.5.2.1.1.23
The alternate firmware version currently stored in system flash.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(1..64)

sysRestoreAltFirmwareVersion		1.3.6.1.4.1.5504.2.5.2.1.1.24
This object can be used to restore the version of firmware to the alternate firmware version currently stored in flash.
Status: current	Access: read-write
OBJECT-TYPE
	SysFirmwareAction

sysSnmpProvisioningLock		1.3.6.1.4.1.5504.2.5.2.1.1.25
This object can be set by an SNMP client to indicate that system configuration is in progress. All other SNMP clients will be locked out while this is set to true. This lock will timeout after 30 seconds.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

sysSnmpProvisioningChange		1.3.6.1.4.1.5504.2.5.2.1.1.26
This object can be incremented by SNMP clients to indicate a sysCfgDBAction save has taken place.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

numberOfBoards		1.3.6.1.4.1.5504.2.5.2.1.2.1
Number of boards in the Unit with Name, Part Number, Serial Number and Revision Number values
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..4

boardDescriptorTable		1.3.6.1.4.1.5504.2.5.2.1.2.2
Table of boards: Name, Part Number, Serial Number and Revision Number values
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		BoardDescriptorEntry

boardDescriptorEntry		1.3.6.1.4.1.5504.2.5.2.1.2.2.1
Table of boards: Name, Part Number, Serial Number and Revision Number values
Status: current	Access: not-accessible
OBJECT-TYPE
	BoardDescriptorEntry

boardIndex		1.3.6.1.4.1.5504.2.5.2.1.2.2.1.1
Board Index (Zero relative)
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..20

boardName		1.3.6.1.4.1.5504.2.5.2.1.2.2.1.2
Name of the Board as created by the system
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

boardPartNumber		1.3.6.1.4.1.5504.2.5.2.1.2.2.1.3
Part Number of the Board. Read from the board
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

boardSerialNumber		1.3.6.1.4.1.5504.2.5.2.1.2.2.1.4
Serial Number of the Board. Read from the board
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

boardRevision		1.3.6.1.4.1.5504.2.5.2.1.2.2.1.5
Revision Number of the Board. Read from the board
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

numberOfPlds		1.3.6.1.4.1.5504.2.5.2.1.3.1
Number of PLDs in the Unit with Name and Version Number values
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..20

pldDescriptorTable		1.3.6.1.4.1.5504.2.5.2.1.3.2
Table of boards: Name, Part Number, Serial Number and Revision Number values
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		PldDescriptorEntry

pldDescriptorEntry		1.3.6.1.4.1.5504.2.5.2.1.3.2.1
Table of boards: Name, Part Number, Serial Number and Revision Number values
Status: current	Access: not-accessible
OBJECT-TYPE
	PldDescriptorEntry

pldIndex		1.3.6.1.4.1.5504.2.5.2.1.3.2.1.1
PLD Index (Zero relative)
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..20

pldName		1.3.6.1.4.1.5504.2.5.2.1.3.2.1.2
Name of the PLD as created by the system
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

pldVersion		1.3.6.1.4.1.5504.2.5.2.1.3.2.1.3
PLD Software Version. Read from the PLD
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

numberOfRadios		1.3.6.1.4.1.5504.2.5.2.1.4.1
Number of Radios in the Unit
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..20

numberOfEthernetLikeInterfaces		1.3.6.1.4.1.5504.2.5.2.1.5.1
Number of Ethernet Like Interfaces with Name, Type and Subtype
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..20

ethernetlikeInterfaceTable		1.3.6.1.4.1.5504.2.5.2.1.5.2
Table of ethernet-like Interfaces
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		EthernetlikeInterfaceEntry

ethernetlikeInterfaceEntry		1.3.6.1.4.1.5504.2.5.2.1.5.2.1
Table of ethernet-like interfaces having Name, type, subtype, number of ports, line power and number of pairs with power
Status: current	Access: not-accessible
OBJECT-TYPE
	EthernetlikeInterfaceEntry

etherIndex		1.3.6.1.4.1.5504.2.5.2.1.5.2.1.1
Index of the Ethernet Like Interface (zero relative)
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..20

etherName		1.3.6.1.4.1.5504.2.5.2.1.5.2.1.2
Name of the ethernet Like Interface as created by the system
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

etherType		1.3.6.1.4.1.5504.2.5.2.1.5.2.1.3
Type of Ethernet interface
Status: current	Access: read-only
OBJECT-TYPE
	ELTYPE

etherSubtype		1.3.6.1.4.1.5504.2.5.2.1.5.2.1.4
Subtype of Ethernet interface
Status: current	Access: read-only
OBJECT-TYPE
	ELSUBTYPE

etherNumberOfPorts		1.3.6.1.4.1.5504.2.5.2.1.5.2.1.5
Number of Ports on the Ethernet interface
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..400

etherLinePower		1.3.6.1.4.1.5504.2.5.2.1.5.2.1.6
Line Power Type on this Ethernet Interface
Status: current	Access: read-only
OBJECT-TYPE
	LPT

etherPowerPairs		1.3.6.1.4.1.5504.2.5.2.1.5.2.1.7
Number of line Pairs providing power on the Ethernet interface
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

numberOfTemperatureSensors		1.3.6.1.4.1.5504.2.5.2.1.6.1
Number of Temperature Sensors in the Unit
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..20

temperatureSensorTable		1.3.6.1.4.1.5504.2.5.2.1.6.2
Table of Temperature Sensors: Name, Maximum, and Minimum values
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		TemperatureSensorEntry

temperatureSensorEntry		1.3.6.1.4.1.5504.2.5.2.1.6.2.1
Table of Temperature Sensors: Name, Maximum, and Minimum values
Status: current	Access: not-accessible
OBJECT-TYPE
	TemperatureSensorEntry

temperatureSensorIndex		1.3.6.1.4.1.5504.2.5.2.1.6.2.1.1
Temperature Sensor Index (Zero relative)
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	0..20

temperatureSensorName		1.3.6.1.4.1.5504.2.5.2.1.6.2.1.2
Name of the ethernet Like Interface as created by the system
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

temperatureSensorMaximum		1.3.6.1.4.1.5504.2.5.2.1.6.2.1.3
Maximum Temperature Recorded
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

temperatureSensorMinimum		1.3.6.1.4.1.5504.2.5.2.1.6.2.1.4
Minimum Temperature Recorded
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

powerSupplyType		1.3.6.1.4.1.5504.2.5.2.1.1.5
Type of Power Supply that the unit is using
Status: current	Access: read-only
OBJECT-TYPE
	UPT

numberOfCommunities		1.3.6.1.4.1.5504.2.5.2.1.7.1
Number of SNMP Communities configured in the Unit
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..9999

zhnCommunityTable		1.3.6.1.4.1.5504.2.5.2.1.7.2
This table is used to set the various configuration parameters for a particular community.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ZhnCommunityTableEntry

zhnCommunityTableEntry		1.3.6.1.4.1.5504.2.5.2.1.7.2.1
This object corresponds to an entry in the community table.
Status: current	Access: not-accessible
OBJECT-TYPE
	ZhnCommunityTableEntry

communityName		1.3.6.1.4.1.5504.2.5.2.1.7.2.1.1
This object corresponds to the SNMP community string.
Status: current	Access: not-accessible
OBJECT-TYPE
	DisplayString

communityType		1.3.6.1.4.1.5504.2.5.2.1.7.2.1.2
The access type of the community string. The default value of this object should be read-only(1).
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	readOnly(1), readWrite(2)

communityRowStatus		1.3.6.1.4.1.5504.2.5.2.1.7.2.1.3
When written, this object can be used to createAndGo(4) or destroy(6) a row from the table. A rowStatus value of notInService(2) will also destroy a row. RowStatus values of active(1), notReady(3), and createAndWait(5) are ignored.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

numberOfTrapManagers		1.3.6.1.4.1.5504.2.5.2.1.8.1
Number of Trap Managers configured in the Unit
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..9999

zhnDefaultTrapCommunity		1.3.6.1.4.1.5504.2.5.2.1.8.2
This object corresponds to the default trap community string. The default trap community string will be used when a community name is not configured for a particular trap manager.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

zhnTrapTypeLinkUpDown		1.3.6.1.4.1.5504.2.5.2.1.8.3
Enable or disable all link up/down traps.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

zhnTrapTypeAuthFailure		1.3.6.1.4.1.5504.2.5.2.1.8.4
Enable or disable the generation of authorization failure traps.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

zhnTrapTypeConfigChange		1.3.6.1.4.1.5504.2.5.2.1.8.5
Enable or disable the generation of configuration change traps. This object is not supported by ZNID devices. Rather, the only mechanism to disable the generation of configuration change traps in a ZNID device is to disable the generation of all enterprise traps via the zhnTrapTypeEnterpise object.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

zhnTrapManagerInfoTable		1.3.6.1.4.1.5504.2.5.2.1.8.6
This table is used to set the trap destination address for a particular community.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ZhnTrapManagerInfoTableEntry

zhnTrapManagerInfoTableEntry		1.3.6.1.4.1.5504.2.5.2.1.8.6.1
This object corresponds to an entry in the community trap address info table.
Status: current	Access: not-accessible
OBJECT-TYPE
	ZhnTrapManagerInfoTableEntry

trapDestination		1.3.6.1.4.1.5504.2.5.2.1.8.6.1.1
The IP Address of the destination to which a trap must be sent.
Status: current	Access: not-accessible
OBJECT-TYPE
	IpAddress

trapCommunityName		1.3.6.1.4.1.5504.2.5.2.1.8.6.1.2
This object corresponds to the trap community string. If not specified, the trapCommunityName will be set to the zhnDefaultTrapCommunity object.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

trapVersion		1.3.6.1.4.1.5504.2.5.2.1.8.6.1.3
The trap types automatically supported by net-snmp and enabled/disabled in snmpd.conf. If not specified, the trapVersion will be set the default value of v2c.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	v1(1), v2c(2)

trapPort		1.3.6.1.4.1.5504.2.5.2.1.8.6.1.4
The udp/tcp port number to which a trap must be sent. If not specified, the trapPort will be set the default value of 162.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65536

trapRowStatus		1.3.6.1.4.1.5504.2.5.2.1.8.6.1.5
When written, this object can be used to createAndGo(4) or destroy(6) a row from the table. A rowStatus value of notInService(2) will also destroy a row. RowStatus values of active(1), notReady(3), and createAndWait(5) are ignored.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

zhnTrapTypeColdStart		1.3.6.1.4.1.5504.2.5.2.1.8.7
Enable or disable the generation of coldstart traps. A coldstart trap is generated each time the device is restarted.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

zhnTrapTypeWarmStart		1.3.6.1.4.1.5504.2.5.2.1.8.8
Enable or disable the generation of warmstart traps. A warmstart trap is generated each time the device's SNMP agent is restarted.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

zhnTrapTypeEnterprise		1.3.6.1.4.1.5504.2.5.2.1.8.9
Enable or disable the generation of all enterprise traps.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	enable(1), disable(2)

zhnFixedCommunityTable		1.3.6.1.4.1.5504.2.5.2.1.7.3
This table is used to configure a read-only and a read-write community.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ZhnFixedCommunityTableEntry

zhnFixedCommunityTableEntry		1.3.6.1.4.1.5504.2.5.2.1.7.3.1
This object corresponds to an entry in the fixed community table.
Status: current	Access: not-accessible
OBJECT-TYPE
	ZhnFixedCommunityTableEntry

fixedCommunityName		1.3.6.1.4.1.5504.2.5.2.1.7.3.1.1
This object corresponds to the SNMP community string.
Status: current	Access: read-create
OBJECT-TYPE
	DisplayString

fixedCommunityType		1.3.6.1.4.1.5504.2.5.2.1.7.3.1.2
The access type of the community string. The default value of this object should be read-only(1).
Status: current	Access: read-create
OBJECT-TYPE
	INTEGER	readOnly(1), readWrite(2)

fixedCommunityRowStatus		1.3.6.1.4.1.5504.2.5.2.1.7.3.1.3
When written, this object is ignored. When read, a value of active(1) or notReady(3) will be returned.
Status: current	Access: read-create
OBJECT-TYPE
	RowStatus

sysLogAdminStatus		1.3.6.1.4.1.5504.2.5.2.1.9.1
Enable or disable the Syslog service.
Status: current	Access: read-write
OBJECT-TYPE
	SysAdminStatus

sysLogLocalLogLevel		1.3.6.1.4.1.5504.2.5.2.1.9.2
SysLog local log level options, per RFC 3164. All logged events with a severity at or greater than this level will be logged to the local log file. Note, the local log file is not persistent across system reboots.
Status: current	Access: read-write
OBJECT-TYPE
	SysLogLevel

sysLogRemoteLogLevel		1.3.6.1.4.1.5504.2.5.2.1.9.3
SysLog remote log level options, per RFC 3164. All logged events with a severity at or greater that this level will be sent to a remote Syslog server if the remote server address is configured and a route exists to the remote server.
Status: current	Access: read-write
OBJECT-TYPE
	SysLogLevel

sysLogDisplayLogLevel		1.3.6.1.4.1.5504.2.5.2.1.9.4
SysLog log level options, per RFC 3164 for the display of log messages via a web browser. All logged events with a severity level at or greater than this level will be displayed.
Status: current	Access: read-write
OBJECT-TYPE
	SysLogLevel

sysLogMode		1.3.6.1.4.1.5504.2.5.2.1.9.5
SysLog logging mode of operation: local(1), -- Log messages only to the local, non-persistent log file remote(2), -- Log messages only to a remote syslog server both(3), -- Log messages to both a local log file and a remote syslog server
Status: current	Access: read-write
OBJECT-TYPE
	SysLogMode

sysLogRemoteServerAddress		1.3.6.1.4.1.5504.2.5.2.1.9.6
The IP address of the remote syslog server.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

sysLogRemoteServerPort		1.3.6.1.4.1.5504.2.5.2.1.9.7
The UDP port to use to transfer syslog messages to the remote syslog server.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	1..65535

sntpAdminStatus		1.3.6.1.4.1.5504.2.5.2.1.10.1
Enable or disable the SNTP client.
Status: current	Access: read-write
OBJECT-TYPE
	SysAdminStatus

sntpOperStatus		1.3.6.1.4.1.5504.2.5.2.1.10.2
Current operational status of the SNTP client.
Status: current	Access: read-write
OBJECT-TYPE
	SysAdminStatus

sntpServer1		1.3.6.1.4.1.5504.2.5.2.1.10.3
The domain name or IP address of the first SNTP server with which to synchronize the system time.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..64)

sntpServer2		1.3.6.1.4.1.5504.2.5.2.1.10.4
The domain name or IP address of the second SNTP server with which to synchronize the system time.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..64)

sntpServer3		1.3.6.1.4.1.5504.2.5.2.1.10.5
The domain name or IP address of the third SNTP server with which to synchronize the system time.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..64)

sntpServer4		1.3.6.1.4.1.5504.2.5.2.1.10.6
The domain name or IP address of the fourth SNTP server with which to synchronize the system time.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..64)

sntpServer5		1.3.6.1.4.1.5504.2.5.2.1.10.7
The domain name or IP address of the fifth SNTP server with which to synchronize the system time.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..64)

sntpLocalTimeZone		1.3.6.1.4.1.5504.2.5.2.1.10.8
Indicates the local time zone.
Status: current	Access: read-write
OBJECT-TYPE
	SysSntpTimeZones

sntpCurrentDateAndTime		1.3.6.1.4.1.5504.2.5.2.1.10.9
Indicates the current date and time.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString

adminUserName		1.3.6.1.4.1.5504.2.5.2.1.11.1
The username required to login as the system administrator. This user has unrestricted access to change and view all configuration, status and test parameters.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..16)

adminPassword		1.3.6.1.4.1.5504.2.5.2.1.11.2
The password required to login as the system administrator. This field cannot contain a SPACE and is returned as a string of asterisks.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..16)

supportUserName		1.3.6.1.4.1.5504.2.5.2.1.11.3
The username required to login to support the system. This user has access to system parameters required to maintain the system and run diagnostic tests.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..16)

supportPassword		1.3.6.1.4.1.5504.2.5.2.1.11.4
The password required to login to support the system. This field cannot contain a SPACE and is returned as a string of asterisks.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..16)

userUserName		1.3.6.1.4.1.5504.2.5.2.1.11.5
The username required to login as a general user of the system. This user can view configuration settings and statistics, as well as, update the system's software.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..16)

userPassword		1.3.6.1.4.1.5504.2.5.2.1.11.6
The password required to login as a general user of the system. field cannot contain a SPACE and is returned as a string of asterisks.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..16)

powerSheddingAdminStatus		1.3.6.1.4.1.5504.2.5.2.1.12.1
Configuration of parameters for the power-shedding feature. The power-shedding objects are only supported by systems that include on-board power-management circuitry. When the system detects that it is running on battery power, it has the option to shut down all support (excluding the voice over IP telephone service).The power-shedding administrative state will enable or disable the power-shedding feature.
Status: current	Access: read-only
OBJECT-TYPE
	SysAdminStatus

powerSheddingShutdownDelay		1.3.6.1.4.1.5504.2.5.2.1.12.2
The shutdown delay is the time delay, in minutes, after AC power is lost, before shutting down non-voice services.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	1..60

powerSheddingRestoreDelay		1.3.6.1.4.1.5504.2.5.2.1.12.3
The restore delay is the time delay, in minutes, after AC power is restored before switching on the services that were shut down due to the power loss.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32	0..10

sysFirewallEnable		1.3.6.1.4.1.5504.2.5.2.1.13.1
Enables or disables the firewall feature for the entire system.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

sysFirewallTcpSynCookies		1.3.6.1.4.1.5504.2.5.2.1.13.2
Enables or disables the TCP SYNCookie protection against SYN flooding denial-of-service attack.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

sysDNSAddressingType		1.3.6.1.4.1.5504.2.5.2.1.14.1
Type of IP interface addressing method used to reach the DNS.
Status: current	Access: read-write
OBJECT-TYPE
	IPInterfaceAddressingTypeValues

sysDNSDHCPSource		1.3.6.1.4.1.5504.2.5.2.1.14.2
Name of the interface used by the DHCP Client to obtain DNS information.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..16)

sysDNSPrimaryIPAddress		1.3.6.1.4.1.5504.2.5.2.1.14.3
Primary Address of DNS when the addressing type is set to Static.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

sysDNSSecondaryIPAddress		1.3.6.1.4.1.5504.2.5.2.1.14.4
Secondary Address of DNS when the addressing type is set to Static.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

zhnDnsProxyHostMaxHostEntries		1.3.6.1.4.1.5504.2.5.2.1.15.1
The maximum number of host entries in the DnsProxyHostObjectTable.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..24

zhnDnsProxyHostTable		1.3.6.1.4.1.5504.2.5.2.1.15.2
This table is used to configure a DNS Proxy Host entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		ZhnDnsProxyHostEntry

zhnDnsProxyHostEntry		1.3.6.1.4.1.5504.2.5.2.1.15.2.1
This object corresponds to an entry in the DNS Proxy Host table.
Status: current	Access: not-accessible
OBJECT-TYPE
	ZhnDnsProxyHostEntry

dnsProxyHostIndex		1.3.6.1.4.1.5504.2.5.2.1.15.2.1.1
Index into the DNS Proxy Host table
Status: current	Access: not-accessible
OBJECT-TYPE
	Unsigned32	1..24

dnsProxyHostIPAddress		1.3.6.1.4.1.5504.2.5.2.1.15.2.1.2
The local proxy host IP address.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

dnsProxyHostName		1.3.6.1.4.1.5504.2.5.2.1.15.2.1.3
The domain name assigned to the host IP address.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING

dnsProxyRowStatus		1.3.6.1.4.1.5504.2.5.2.1.15.2.1.4
Create or destroy a DNS Proxy Host. Upon creation, the dnsProxyHostIPAddress must be provided.
Status: current	Access: read-create
OBJECT-TYPE
	ZhoneRowStatus

failoverTimer		1.3.6.1.4.1.5504.2.5.2.1.16.1
The WAN Failover Timer is used to determine how long (in seconds) the Fiber uplink interface must be operationally DOWN before a USB Cellular WAN Backup connection will be initiated. The Default value is 0 seconds, which DISABLES this feature. The recommended value to enable this feature is 60 seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

restoralTimer		1.3.6.1.4.1.5504.2.5.2.1.16.2
The WAN Restoral Timer is used to determine how long (in seconds) the Fiber uplink interface must remain in an operational UP condition before the Cellular Backup connection will be terminated and the traffic that was being forwarded out the USB interface is forwarded to the 5xx GEM instead. The default value is 60 seconds.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

backupDataVlan		1.3.6.1.4.1.5504.2.5.2.1.16.3
This is the Internet Access VLAN (GEM 5xx), which is the only service that can be backed up using the USB Cellular modem.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..4096

cellularPinNumber		1.3.6.1.4.1.5504.2.5.2.1.16.4
A 4 digit PIN code used to unlock the SIM card. For GPRS/UMTS networks, *99# is typically used. For CDMA/EVDO networks, #777 is typically used.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..4)

cellularDataNumber		1.3.6.1.4.1.5504.2.5.2.1.16.5
This is the number that the USB modem will dial to establish a cellular a cellular data connection. For GPRS/UMTS networks, *99# is typically used. For CDMA/EVDO networks, #777 is typically used.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..32)

atInitCommands		1.3.6.1.4.1.5504.2.5.2.1.16.6
AT initialization command strings, if needed.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..256)

accessPointName		1.3.6.1.4.1.5504.2.5.2.1.16.7
The Access Point Name (APN) for connections to the GPRS/UMTS network. This should be provided by the ISP. In North America, 3G cellular carriers do not require an APN.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..32)

chapPapUsername		1.3.6.1.4.1.5504.2.5.2.1.16.8
Required for CHAP or PAP authentication. This configuration item should be left blank if CHAP or PAP is not used.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..32)

chapPapPassword		1.3.6.1.4.1.5504.2.5.2.1.16.9
Required for CHAP or PAP authentication. This configuration item should be left blank if CHAP or PAP is not used.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..32)

connectionTimeout		1.3.6.1.4.1.5504.2.5.2.1.16.10
Specifies the duration of inactivity in seconds before the cellular data call will automatically terminate. A new call will be initiated automatically when a packet must be sent upstream on the designated VLAN if the WAN uplink is still Operationally Down. A value of 0 will DISABLE the Connection Timeout feature.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

backupIpAddressMode		1.3.6.1.4.1.5504.2.5.2.1.16.11
The WAN IP Address, Default Gateway IP Address, Subnet Mask and DNS Server IP Address must all be defined for the USB Cellular Backup connection. When IP Address Mode is set to DHCP, a DHCP Request will be sent upstream after the Cellular Data Connection has been established to acquire this information dynamically. When the WAN Backup IP Addess Mode is set to Static, this information ust be statically configured.
Status: current	Access: read-write
OBJECT-TYPE
	BasicAddressingTypeValues

backupIpAddress		1.3.6.1.4.1.5504.2.5.2.1.16.12
The IP Address to be used on the WAN uplink interface of a Cellular Backhaul connection. This parameter is acquired dynamically in DHCP mode and only configurable if the BackupIpAddressMode is Static.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

backupDefaultGateway		1.3.6.1.4.1.5504.2.5.2.1.16.13
The IP Address of the Default Gateway to be used on the WAN uplink interface of a Cellular Backhaul connection. This parameter is acquired dynamically in DHCP mode and only configurable if the BackupIpAddressMode is Static.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

backupSubnetMask		1.3.6.1.4.1.5504.2.5.2.1.16.14
The Subnet Mask to be used on the WAN uplink interface of a Cellular Backhaul connection. This parameter is acquired dynamically in DHCP mode and only configurable if the BackupIpAddressMode is Static.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

backupPrimaryDns		1.3.6.1.4.1.5504.2.5.2.1.16.15
The IP Address of the Primary DNS Server to be used on the WAN uplink interface of a Cellular Backhaul connection. This parameter is acquired dynamically in DHCP mode and only configurable if the BackupIpAddressMode is Static.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

backupSecondaryDns		1.3.6.1.4.1.5504.2.5.2.1.16.16
The IP Address of the Secondary DNS Server to be used on the WAN uplink interface of a Cellular Backhaul connection. This parameter is acquired dynamically in DHCP mode and only configurable if the BackupIpAddressMode is Static.
Status: current	Access: read-write
OBJECT-TYPE
	IpAddress

sysTr69cConfigObjects		1.3.6.1.4.1.5504.2.5.2.1.17.1
OBJECT IDENTIFIER

sysTr69cServerObjects		1.3.6.1.4.1.5504.2.5.2.1.17.2
OBJECT IDENTIFIER

sysTr69cConfigLoggingSOAP		1.3.6.1.4.1.5504.2.5.2.1.17.1.1
Enable or disable showing SOAP messages on serial console and local TR69 Client log file.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

sysTr69cConfigConnectionRequestAuthentication		1.3.6.1.4.1.5504.2.5.2.1.17.1.2
Enable or disable connection request authentication.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

sysTr69cServerURL		1.3.6.1.4.1.5504.2.5.2.1.17.2.1
URL for the CPE to connect to the ACS using the CPE WAN Management Protocol. This parameter MUST be in the form of a valid HTTP or HTTPS URL. The host portion of this URL is used by the CPE for server-side certificate authentication when using SSL or TLS.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..256)

sysTr69cServerLastConnectedURL		1.3.6.1.4.1.5504.2.5.2.1.17.2.2
This value records the last URL which connected successfully to the TR69 client.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..256)

sysTr69cServerUsername		1.3.6.1.4.1.5504.2.5.2.1.17.2.3
Username used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol. This username is used only for HTTP-based authentication of the CPE.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..256)

sysTr69cServerPassword		1.3.6.1.4.1.5504.2.5.2.1.17.2.4
Password used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol. This username is used only for HTTP-based authentication of the CPE. When read by an ACS, this parameter returns an empty string, regardless of the value.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..256)

sysTr69cServerPeriodicInformEnable		1.3.6.1.4.1.5504.2.5.2.1.17.2.5
When set to TRUE, the CPE will periodically send CPE information to the TR69 Server using the Inform method calls.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

sysTr69cServerPeriodicInformInterval		1.3.6.1.4.1.5504.2.5.2.1.17.2.6
The duration in seconds of the interval for which the CPE MUST attempt to connect with the ACS and call the Inform method if PeriodicInform-Enable is true.
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32

sysTr69cServerParameterKey		1.3.6.1.4.1.5504.2.5.2.1.17.2.7
ParameterKey provides the ACS a reliable and extensible means to track changes made by the ACS. The value of ParameterKey MUST be equal to the value of the ParameterKey argument from the most recent successful SetParameterValues, AddObject, or DeleteObject method call from the ACS. The CPE MUST set ParameterKey to the value specified in the corresponding method arguments if and only if the method completes successfully and no fault response is generated. If a method call does not complete successfully implying that the changes requested in the method did not take effect, the value of ParameterKey MUST NOT be modified. The CPE MUST only modify the value of ParameterKey as a result of SetParameterValues, AddObject, DeleteObject, or due to a factory reset. On factory reset, the value of ParameterKey MUST be set to empty.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sysTr69cServerBoundIfName		1.3.6.1.4.1.5504.2.5.2.1.17.2.8
Name of the WAN interface that the TR69 client should use when establishing communications with the ACS.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..32)

sysTr69cServerConnectionRequestURL		1.3.6.1.4.1.5504.2.5.2.1.17.2.9
HTTP URL for an ACS to make a Connection Request notification to the CPE. In the form: http://host:port/path. The host portion of the URL MAY be the IP address for the management interface of the CPE in lieu of a host name.
Status: current	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(0..256)

sysTr69cServerConnectionRequestUsername		1.3.6.1.4.1.5504.2.5.2.1.17.2.10
Username used to authenticate an ACS making a Connection Request to the CPE.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..256)

sysTr69cServerConnectionRequestPassword		1.3.6.1.4.1.5504.2.5.2.1.17.2.11
Password used to authenticate an ACS making a Connection Request to the CPE. When read by an ACS, this parameter returns an empty string, regardless of the actual value.
Status: current	Access: read-write
OBJECT-TYPE
	OCTET STRING	Size(0..256)

sysTr69cServerUpgradesManaged		1.3.6.1.4.1.5504.2.5.2.1.17.2.12
Indicates whether or not the ACS will manage upgrades for the CPE. If true (1), the CPE SHOULD not use other means other than the ACS to seek out available upgrades. If false (0), the CPE MAY use other means for this purpose.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

zhnSystemConformance		1.3.6.1.4.1.5504.2.5.2.2
OBJECT IDENTIFIER

zhnSystemGroups		1.3.6.1.4.1.5504.2.5.2.2.1
OBJECT IDENTIFIER

zhnSystemCompliances		1.3.6.1.4.1.5504.2.5.2.2.2
OBJECT IDENTIFIER

zhnSystemCompliance		1.3.6.1.4.1.5504.2.5.2.2.2.1
The Compliance statement for SNMP entities which manage the display of Zhone System Information
Status: current	Access: read-only
MODULE-COMPLIANCE

zhnSystemActiveGroup		1.3.6.1.4.1.5504.2.5.2.2.1.1
A collection of System Information objects that are required for the device to be functional
Status: current	Access: read-only
OBJECT-GROUP

zhnSystemTablesItems		1.3.6.1.4.1.5504.2.5.2.2.1.2
The table items for the device that are filled in when the table is present
Status: current	Access: read-only
OBJECT-GROUP

zhnSystemConfigItems		1.3.6.1.4.1.5504.2.5.2.2.1.3
The collection of configurable scalar system objects.
Status: current	Access: read-only
OBJECT-GROUP

zhnSystemTrapItems		1.3.6.1.4.1.5504.2.5.2.2.1.4
The collection of SNMP trap objects.
Status: current	Access: read-only
OBJECT-GROUP

zhnSystemCommunityItems		1.3.6.1.4.1.5504.2.5.2.2.1.5
The collection of SNMP community objects.
Status: current	Access: read-only
OBJECT-GROUP

zhnSystemFixedCommunityItems		1.3.6.1.4.1.5504.2.5.2.2.1.6
The collection of pre-provisioned SNMP community objects.
Status: current	Access: read-only
OBJECT-GROUP

zhnSystemClockingItems		1.3.6.1.4.1.5504.2.5.2.2.1.7
The collection of system-wide clocking parameters only supported by ZNID devices.
Status: current	Access: read-only
OBJECT-GROUP

zhnSyslogConfigGroup		1.3.6.1.4.1.5504.2.5.2.2.1.8
The collection of system-wide logging parameters only supported by ZNID devices.
Status: current	Access: read-only
OBJECT-GROUP

zhnSntpConfigGroup		1.3.6.1.4.1.5504.2.5.2.2.1.9
The collection of SNTP server parameters only supported by ZNID devices.
Status: current	Access: read-only
OBJECT-GROUP

zhnUserLoginGroup		1.3.6.1.4.1.5504.2.5.2.2.1.10
The collection of User login parameters only supported by ZNID devices.
Status: current	Access: read-only
OBJECT-GROUP

zhnPowerSheddingGroup		1.3.6.1.4.1.5504.2.5.2.2.1.11
The collection of configurable power-shedding parameters only supported by ZNID devices.
Status: current	Access: read-only
OBJECT-GROUP

zhnSystemFirewallGroup		1.3.6.1.4.1.5504.2.5.2.2.1.12
The collection of system firewall parameters only supported by ZNID devices.
Status: current	Access: read-only
OBJECT-GROUP

zhnSystemDNSClientGroup		1.3.6.1.4.1.5504.2.5.2.2.1.13
The collection of system DNS Client parameters only supported by ZNID devices.
Status: current	Access: read-only
OBJECT-GROUP

zhnSystemDNSProxyHostGroup		1.3.6.1.4.1.5504.2.5.2.2.1.14
The collection of system DNS Proxy Host parameters only supported by ZNID devices.
Status: current	Access: read-only
OBJECT-GROUP

zhnSystemWanBackupGroup		1.3.6.1.4.1.5504.2.5.2.2.1.15
The collection of system WAN Backup parameters only supported by ZNID devices.
Status: current	Access: read-only
OBJECT-GROUP

zhnSystemTr69cGroup		1.3.6.1.4.1.5504.2.5.2.2.1.16
The collection of system TR69 Client parameters only supported by ZNID devices.
Status: current	Access: read-only
OBJECT-GROUP

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor