XPRESS-MIB

File: XPRESS-MIB.mib (290599 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB
RFC-1215

Imported symbols

enterprises Counter Gauge
NetworkAddress IpAddress TimeTicks
OBJECT-TYPE PhysAddress DisplayString
TRAP-TYPE

Defined Types

RowStatus  
INTEGER active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6)    

RlanCardEntry  
SEQUENCE    
  rCardID INTEGER
  rCardType INTEGER
  rCardAdmst INTEGER
  rCardStatus INTEGER
  rCardDiag INTEGER
  rCardOpState INTEGER
  rCardSWRev DisplayString
  rCardHWRev DisplayString
  rCardTotalRAM INTEGER
  rCardBRISwitch INTEGER
  rCardBootProm DisplayString
  rCardReset INTEGER
  rCardTearDown INTEGER
  rCardRowStatus RowStatus
  rCardPriActivate INTEGER

RlanDChanStatsEntry  
SEQUENCE    
  rDChanCardID INTEGER
  rDChanPortID INTEGER
  rDChanState INTEGER
  rDChanRxFrames Counter
  rDChanRxCRCErrs Counter
  rDChanRxOverErrs Counter
  rDChanRxOverflows Counter
  rDChanRxAborts Counter
  rDChanRxCalls Counter
  rDChanTxFrames Counter
  rDChanTxUnderErrs Counter
  rDChanTxCalls Counter
  rDChanLostDSLs Counter
  rDChanColls Counter
  rDChanFrameSlips Counter
  rDChanLinkFaults Counter

RlanDChanConfigEntry  
SEQUENCE    
  rDChanStatus INTEGER
  rDChanFaultThreshold INTEGER
  rDChanDOSBS INTEGER
  rDChanBriNetSync INTEGER

RlanChannelConfigEntry  
SEQUENCE    
  rChanCardID INTEGER
  rChanPortID INTEGER
  rChanID INTEGER
  rChanOpMode INTEGER
  rChanChannelGroup INTEGER
  rChanHuntGroup INTEGER
  rChanOtherChan INTEGER

RlanBriChanConfigEntry  
SEQUENCE    
  rBChanPhoneNum DisplayString
  rBChanSPID DisplayString

RlanSerialChanConfigEntry  
SEQUENCE    
  rChanCallCtrl INTEGER
  rChanHoldOff INTEGER
  rChanCallSetupTO INTEGER

RlanSyncChanStatsEntry  
SEQUENCE    
  rSyncChanWANStatsIndex INTEGER
  rSyncChanLinkState INTEGER
  rSyncChanRxFrames Counter
  rSyncChanRxOctets Counter
  rSyncChanRxFrameErrs Counter
  rSyncChanRxCRCErrs Counter
  rSyncChanRxOverErrs Counter
  rSyncChanRxAborts Counter
  rSyncChanRxShortFrames Counter
  rSyncChanRxLongFrames Counter
  rSyncChanTxFrames Counter
  rSyncChanTxOctets Counter
  rSyncChanTxFrameErrs Counter
  rSyncChanTxUnderErrs Counter
  rSyncChanTxAborts Counter
  rSyncChanLinkFaults Counter
  rSyncChanResourceShorts Counter
  rSyncChanLastResultCode INTEGER
  rSyncChanConnectedPhnum DisplayString
  rSyncChanConnectedName DisplayString

RlanIsdnBChanEntry  
SEQUENCE    
  rIsdnBChanBearer INTEGER
  rIsdnBChanLlSpeed INTEGER

RlanSerialChanStatsEntry  
SEQUENCE    
  rSerialChanIfType INTEGER
  rSerialChanRole INTEGER
  rSerialChanCtlSignals INTEGER
  rSerialChanLoopBack INTEGER
  rSerialChanInConnects Counter
  rSerialChanOutConnects Counter
  rSerialChanOutConnectFails Counter

RlanChannelGroupEntry  
SEQUENCE    
  rChannelGroupId INTEGER
  rChannelGroupName DisplayString
  rChannelGroupStatus RowStatus

RlanChannelDiagnosticEntry  
SEQUENCE    
  rChanDiagRemLANID INTEGER
  rChanDiagForce INTEGER

RlanHuntGroupEntry  
SEQUENCE    
  rHuntGroupIndex INTEGER
  rHuntGroupName DisplayString
  rHuntGroupPhoneNum DisplayString
  rHuntGroupRowStatus RowStatus

RlanPBXChanGroupEntry  
SEQUENCE    
  rPBXChanExtensionNumber DisplayString
  rPBXChanModuleType INTEGER
  rPBXChanPhoneType INTEGER
  rPBXChanEncoding INTEGER

RlanResourceModuleEntry  
SEQUENCE    
  rResourceModuleOffline INTEGER
  rResourceModuleLinkstate INTEGER

RlanPBXChanNTStatsEntry  
SEQUENCE    
  rPBXChanNTVoiceTimingPackets Counter
  rPBXChanNTSignalCrcErr Counter
  rPBXChanNTInvalidAddress Counter
  rPBXChanNTSignalRejects Counter
  rPBXChanNTMaxRetryErr Counter
  rPBXChanNTLostSyncErr Counter
  rPBXChanNTNoDataSignal Counter
  rPBXChanNTAckTimeout Counter
  rPBXChanNTTransLockup Counter
  rPBXChanNTReinitTries Counter
  rPBXChanNTDiscFails Counter
  rPBXChanNTRetrans Counter
  rPBXChanNTInternalDisc Counter
  rPBXChanNTFatalPanics Counter
  rPBXChanNTLinkIntegrity Counter
  rPBXChanNTRxFails Counter
  rPBXChanNTTxFails Counter
  rPBXChanNTCallsRx Counter
  rPBXChanNTCallsTx Counter

RlanWANStatsEntry  
SEQUENCE    
  rWANStatsIndex INTEGER
  rWANStatsCardID INTEGER
  rWANStatsPortID INTEGER
  rWANStatsChanID INTEGER
  rWANStatsRemLANID INTEGER
  rWANStatsRemLANName DisplayString
  rWANStatsRxFrames Counter
  rWANStatsRxOctets Counter
  rWANStatsRxFrameErrs Counter
  rWANStatsRxCRCErrs Counter
  rWANStatsRxOverErrs Counter
  rWANStatsRxAborts Counter
  rWANStatsRatioErrRx INTEGER
  rWANStatsTxFrames Counter
  rWANStatsTxOctets Counter
  rWANStatsTxFrameErrs Counter
  rWANStatsTxUnderErrs Counter
  rWANStatsTxAborts Counter
  rWANStatsRatioErrTx INTEGER
  rWANStatsDuration TimeTicks
  rWANStatsChanSpeed INTEGER
  rWANStatsRemExtID INTEGER
  rWANStatsRemExtName DisplayString
  rWANStatsRMCardID INTEGER
  rWANStatsRMPortID INTEGER
  rWANStatsRMChanID INTEGER

RlanWANStatsRMChanEntry  
SEQUENCE    
  rWANStatsRMWanIndex INTEGER
  rWANStatsRMChanIndex INTEGER
  rWANStatsRMChanCardID INTEGER
  rWANStatsRMChanPortID INTEGER
  rWANStatsRMChanChanID INTEGER
  rWANStatsRMChanConnectedPhnum DisplayString
  rWANStatsRMChanConnectedName DisplayString

RlanRemLANConfigEntry  
SEQUENCE    
  rRemLANID INTEGER
  rRemLANName DisplayString
  rRemLANOpMode INTEGER
  rRemLANOutMinBearer INTEGER
  rRemLANCompression INTEGER
  rRemLANWanProtocol INTEGER
  rRemLANIdleTimeout INTEGER
  rRemLANMaxChannels INTEGER
  rRemLANFlooding INTEGER
  rRemLANMCastFwd INTEGER
  rRemLANBCastFwd INTEGER
  rRemLANCallForce INTEGER
  rRemLANWatchdogSpoofing INTEGER
  rRemLANSAPandRIPSpoofingFiltering INTEGER
  rRemLANSAPGroups OCTET STRING
  rRemLANStatus RowStatus
  rRemLANAroundCorner INTEGER
  rRemLANPPPNcpTypes INTEGER
  rRemLANHuntGroup INTEGER
  rRemLANMdmAnswer INTEGER
  rRemLANEncryption INTEGER
  rRemLANSNASpoofing INTEGER
  rRemLANDialBack INTEGER
  rRemLANTestPresence DisplayString
  rRemLANAllAtOnce INTEGER

RlanGandalfProtoConfigEntry  
SEQUENCE    
  rRemLANSerialNumber OCTET STRING

RlanPppConfigEntry  
SEQUENCE    
  rRemLANPppAuth INTEGER
  rRemLANPppSecret OCTET STRING
  rRemLANPppNCP INTEGER
  rRemLANRemIPAddrHandling INTEGER
  rRemLANPPPRemIPAddr IpAddress
  rRemLANPPPBapHandling INTEGER

RlanDestAddressConfigEntry  
SEQUENCE    
  rDestAddrId INTEGER
  rDestPrefix INTEGER
  rDestPhoneNum DisplayString
  rDestChannelGroupId INTEGER
  rDestLANCLID DisplayString
  rDestLANMdmRequest INTEGER

RlanAddressPrefixConfigEntry  
SEQUENCE    
  rAddrPrefixId INTEGER
  rAddrPrefixName DisplayString
  rAddrPrefixString OCTET STRING
  rAddrPrefixStatus RowStatus

RlanRemLANStatsEntry  
SEQUENCE    
  rRemLANWANStatsIndex OCTET STRING
  rRemLANLastBearer INTEGER
  rRemLANLastFail INTEGER
  rRemLANLastTime TimeTicks
  rRemLANInCompressedBits Counter
  rRemLANInUncompressedBits Counter
  rRemLANInFrames Counter
  rRemLANInUCastFwds Counter
  rRemLANInUCastFilts Counter
  rRemLANInMCastFwds Counter
  rRemLANInMCastFilts Counter
  rRemLANInBCastFwds Counter
  rRemLANInBCastFilts Counter
  rRemLANOutCompressedBits Counter
  rRemLANOutUncompressedBits Counter
  rRemLANOutFrames Counter
  rRemLANOutUCastFwds Counter
  rRemLANOutMCastFwds Counter
  rRemLANOutBCastFwds Counter
  rRemLANDiscTrans Counter
  rRemLANResShorts Counter
  rRemLANDuration TimeTicks
  rRemLANRemoteIP IpAddress
  rRemLANCompressionResetsRx Counter
  rRemLANCompressionResetsTx Counter
  rRemLANLocalDecompressionType INTEGER
  rRemLANLocalCompressionType INTEGER
  rRemLANBcpStatus INTEGER
  rRemLANIpcpStatus INTEGER
  rRemLANIpxcpStatus INTEGER
  rRemLANBacpStatus INTEGER
  rRemLANMpplusStatus INTEGER
  rRemLANDynamic INTEGER
  rRemLANUserMustAuthenticate INTEGER
  rRemLANLastConnected DisplayString

RlanMACFilterEntry  
SEQUENCE    
  rMACID PhysAddress
  rMACType INTEGER
  rMACHomePort INTEGER

RFtpConfigEntry  
SEQUENCE    
  rFtpFileId INTEGER
  rFtpServerIpAddr IpAddress
  rFtpClientId DisplayString
  rFtpClientPasswd DisplayString
  rFtpFilePath DisplayString
  rFtpFileName DisplayString
  rFtpOperation INTEGER

RlanBlacklistEntry  
SEQUENCE    
  rBlacklistID INTEGER
  rBlacklistCLID DisplayString
  rBlacklistStatus RowStatus

RlanProtocolEntry  
SEQUENCE    
  rProtocolID NetworkAddress
  rProtocolMask NetworkAddress
  rProtocolRemLANID INTEGER
  rProtocolType INTEGER
  rProtocolStatus RowStatus

RlanPriPortEntry  
SEQUENCE    
  rPortCardID INTEGER
  rPortPortID INTEGER
  rPortCardType INTEGER
  rPortLineFormat INTEGER
  rPortPRISwitch INTEGER
  rPortDChanFormat INTEGER
  rPortDChanTimeslot INTEGER
  rPortYellowAlarm INTEGER
  rPortAISAlarm INTEGER
  rPortRedAlarm INTEGER
  rPortPhoneNumber DisplayString
  rPortAdmst INTEGER
  rPortDLinkNum INTEGER
  rPortIfId INTEGER
  rPortDOSBS INTEGER
  rPortHuntGroup INTEGER
  rPortHoldoff INTEGER
  rPortNetsync INTEGER
  rPortPBXType INTEGER

RlanPortIsdnRoutingEntry  
SEQUENCE    
  rPortIsdnRouting INTEGER

RlanPortPBXRoutingEntry  
SEQUENCE    
  rPortPBXRouting INTEGER

RlanSAPEntry  
SEQUENCE    
  rSAPServiceType INTEGER
  rSAPServerName OCTET STRING
  rSAPType INTEGER
  rSAPNetworkAddress OCTET STRING
  rSAPNodeAddress OCTET STRING
  rSAPSocketAddress INTEGER
  rSAPHops INTEGER
  rSAPGroup INTEGER
  rSAPStatus RowStatus

RlanSAPGroupEntry  
SEQUENCE    
  rSAPGroupId INTEGER
  rSAPGroupName DisplayString
  rSAPGroupStatus RowStatus

RlanRIPEntry  
SEQUENCE    
  rRIPNetworkAddress OCTET STRING
  rRIPHops INTEGER
  rRIPTicks TimeTicks
  rRIPMACAddress PhysAddress

RlanSnmpCommunityEntry  
SEQUENCE    
  rSnmpCommunityIndex INTEGER
  rSnmpCommunityName DisplayString
  rSnmpCommunityIpAddr IpAddress
  rSnmpCommunityPriv INTEGER
  rSnmpCommunityViewIndex INTEGER
  rSnmpCommunityRowStatus RowStatus

RlanSnmpTrapCommunityEntry  
SEQUENCE    
  rSnmpTrapCommunityIndex INTEGER
  rSnmpTrapCommunityName DisplayString
  rSnmpTrapIpAddr IpAddress
  rSnmpTrapRemotePort INTEGER
  rSnmpTrapStatus RowStatus

RlanSnmpViewNameEntry  
SEQUENCE    
  rSnmpViewNameIndex INTEGER
  rSnmpViewName DisplayString
  rSnmpViewNameStatus RowStatus

RlanSnmpViewEntry  
SEQUENCE    
  rSnmpViewSubtree OBJECT IDENTIFIER
  rSnmpViewMask OCTET STRING
  rSnmpViewType INTEGER
  rSnmpViewStatus RowStatus

RlanSnmpTrapProfileEntry  
SEQUENCE    
  rSnmpTrapEnterprise OBJECT IDENTIFIER
  rSnmpTrapId INTEGER
  rSnmpCommunities OCTET STRING

RlanFlashDirectoryEntry  
SEQUENCE    
  rFlashFileIndex INTEGER
  rFlashFileType DisplayString
  rFlashFileId INTEGER
  rFlashFileAddress OCTET STRING
  rFlashFileSize INTEGER
  rFlashFileVersion DisplayString
  rFlashFileCrc INTEGER

RlanLANProtocolIDEntry  
SEQUENCE    
  rLANProtocolIDId INTEGER
  rLANProtocolID INTEGER
  rLANProtocolIDName DisplayString
  rLANProtocolIDStatus RowStatus

RlanMdmIDEntry  
SEQUENCE    
  rMdmIDManufacturerOID OBJECT IDENTIFIER
  rMdmIDProductDetails DisplayString

RlanMdmLineEntry  
SEQUENCE    
  rMdmLineState INTEGER

RlanMdmECEntry  
SEQUENCE    
  rMdmECErrorControlUsed INTEGER

RlanMdmDCEntry  
SEQUENCE    
  rMdmDCCompressionTypeUsed INTEGER

RlanMdmSCEntry  
SEQUENCE    
  rMdmSCCurrentLineTransmitRate INTEGER 0..2147483647
  rMdmSCCurrentLineReceiveRate INTEGER 0..2147483647
  rMdmSCModulationSchemeUsed INTEGER

RlanMdmStatsEntry  
SEQUENCE    
  rMdmStatsRetrains Counter
  rMdmStatsSentOctets Counter
  rMdmStatsReceivedOctets Counter
  rMdmStatsSentDataFrames Counter
  rMdmStatsReceivedDataFrames Counter
  rMdmStatsResentFrames Counter
  rMdmStatsErrorFrames Counter
  rMdmStatsDisconnectCause INTEGER
  rMdmStatsControlList INTEGER
  rMdmStatsReceiveLevel INTEGER
  rMdmStatsTransmitLevel INTEGER
  rMdmStatsSignalToNoiseRatio INTEGER
  rMdmStatsSpeedChanges INTEGER

RlanMdmACCMEntry  
SEQUENCE    
  rMdmACCMRx DisplayString
  rMdmACCMTx DisplayString

RlanRemExtConfigEntry  
SEQUENCE    
  rRemExtID INTEGER
  rRemExtName DisplayString
  rRemExtPbxExtension DisplayString
  rRemExtAdminState INTEGER
  rRemExtPasswdAdminState INTEGER
  rRemExtPasswd DisplayString
  rRemExtIdleDisconnectTimer INTEGER
  rRemExtTimeOfDayProfileId INTEGER
  rRemExtConnectedToCard INTEGER
  rRemExtConnectedToModule INTEGER
  rRemExtConnectedToChannel INTEGER
  rRemExtPhoneEndPhNumber DisplayString
  rRemExtSwitchEndPhNumber DisplayString
  rRemExtDialPrefix INTEGER
  rRemExtChannelGroup INTEGER
  rRemExtCLID DisplayString
  rRemExtMakeSetBusyAdminState INTEGER
  rRemExtMakeSetBusyKey DisplayString
  rRemExtLogoutSequence DisplayString
  rRemExtCallProcessing INTEGER
  rRemExtStatus RowStatus
  rRemExtCallForce INTEGER
  rRemExtLineKey OCTET STRING
  rRemExtRxGain INTEGER
  rRemExtTxGain INTEGER
  rRemExtPbxInterface INTEGER
  rRemExtOutgoingBearer INTEGER
  rRemExtDivertImmediate DisplayString
  rRemExtDivertBusy DisplayString
  rRemExtDivertNoAnswer DisplayString
  rRemExtOfficeExtension DisplayString

RlanRemExtStatsEntry  
SEQUENCE    
  rRemExtVoiceModule INTEGER
  rRemExtIsdnChan INTEGER
  rRemExtTotalTime TimeTicks
  rRemExtLastTime TimeTicks
  rRemExtCallDuration TimeTicks
  rRemExtLastFail INTEGER
  rRemExtWANStatsIndex INTEGER

RlanTimeOfDayProfileEntry  
SEQUENCE    
  rTimeOfDayProfileID INTEGER
  rTimeOfDayProfileName DisplayString
  rTimeOfDayProfileStatus RowStatus

RlanTimeOfDayEntry  
SEQUENCE    
  rTimeOfDayEntryID INTEGER
  rTimeOfDayEntryStart INTEGER
  rTimeOfDayEntryEnd INTEGER
  rTimeOfDayEntryIdleDisconnect INTEGER
  rTimeOfDayEntryExclusive INTEGER

RlanDpnssBchConfigEntry  
SEQUENCE    
  rDpnssBchCardID INTEGER
  rDpnssBchPortID INTEGER
  rDpnssBchChanID INTEGER
  rDpnssBchRealXy INTEGER
  rDpnssBchVirtualMode INTEGER
  rDpnssBchVirtualXy INTEGER

RlanIsdnDDIRoutingEntry  
SEQUENCE    
  rIsdnDDIRtgIndex INTEGER
  rIsdnDDIRtgName DisplayString
  rIsdnDDIRtgRacLoPhnum DisplayString
  rIsdnDDIRtgRacHiPhnum DisplayString
  rIsdnDDIRtgApexPhnum DisplayString
  rIsdnDDIRtgAbsorb INTEGER
  rIsdnDDIRtgInsert DisplayString
  rIsdnDDIRtgRowStatus RowStatus

RlanPbxCallRoutingEntry  
SEQUENCE    
  rPbxCallRtgIndex INTEGER
  rPbxCallRtgName DisplayString
  rPbxCallRtgGwayPhnum DisplayString
  rPbxCallRtgGwayAbsorb INTEGER
  rPbxCallRtgRacExtLo DisplayString
  rPbxCallRtgRacExtHi DisplayString
  rPbxCallRtgApexExtLo DisplayString
  rPbxCallRtgApexExtHi DisplayString
  rPbxCallRtgRowStatus RowStatus

RlanSecurityBannerConfigEntry  
SEQUENCE    
  rSecBannerBanner DisplayString
  rSecBannerLogin DisplayString
  rSecBannerPassword DisplayString
  rSecBannerAccepted DisplayString
  rSecBannerDenied DisplayString
  rSecBannerPart1 DisplayString
  rSecBannerPart2 DisplayString
  rSecBannerPart3 DisplayString

RlanIpRoutingConfigEntry  
SEQUENCE    
  rIpRoutingArpProxy INTEGER
  rIpRoutingRipForwarding INTEGER
  rIpRoutingRipType INTEGER

Defined Values

gandalf 1.3.6.1.4.1.64
OBJECT IDENTIFIER    

gandalf-rlanisdn 1.3.6.1.4.1.64.9
OBJECT IDENTIFIER    

rlanSystemGroup 1.3.6.1.4.1.64.9.1
OBJECT IDENTIFIER    

rlanCardGroup 1.3.6.1.4.1.64.9.2
OBJECT IDENTIFIER    

rlanDChanGroup 1.3.6.1.4.1.64.9.3
OBJECT IDENTIFIER    

rlanChannelGroup 1.3.6.1.4.1.64.9.4
OBJECT IDENTIFIER    

rlanWANStatsGroup 1.3.6.1.4.1.64.9.5
OBJECT IDENTIFIER    

rlanWANSummationGroup 1.3.6.1.4.1.64.9.6
OBJECT IDENTIFIER    

rlanRemLANGroup 1.3.6.1.4.1.64.9.7
OBJECT IDENTIFIER    

rlanLocLANGroup 1.3.6.1.4.1.64.9.8
OBJECT IDENTIFIER    

rlanLocLANFilterGroup 1.3.6.1.4.1.64.9.9
OBJECT IDENTIFIER    

rlanFilterCfgGroup 1.3.6.1.4.1.64.9.10
OBJECT IDENTIFIER    

rlanMACFilterGroup 1.3.6.1.4.1.64.9.11
OBJECT IDENTIFIER    

rlanTCPIPGroup 1.3.6.1.4.1.64.9.12
OBJECT IDENTIFIER    

rlanBlacklistGroup 1.3.6.1.4.1.64.9.13
OBJECT IDENTIFIER    

rlanProtocolGroup 1.3.6.1.4.1.64.9.14
OBJECT IDENTIFIER    

rlanPriPortGroup 1.3.6.1.4.1.64.9.15
OBJECT IDENTIFIER    

rlanIPXGroup 1.3.6.1.4.1.64.9.16
OBJECT IDENTIFIER    

rlanSAPGroup 1.3.6.1.4.1.64.9.17
OBJECT IDENTIFIER    

rlanRIPGroup 1.3.6.1.4.1.64.9.18
OBJECT IDENTIFIER    

rlanSnmpGroup 1.3.6.1.4.1.64.9.19
OBJECT IDENTIFIER    

rlanAuditGroup 1.3.6.1.4.1.64.9.20
OBJECT IDENTIFIER    

rlanFlashGroup 1.3.6.1.4.1.64.9.21
OBJECT IDENTIFIER    

rlanLANProtocolIDGroup 1.3.6.1.4.1.64.9.22
OBJECT IDENTIFIER    

rlanModemGroup 1.3.6.1.4.1.64.9.23
OBJECT IDENTIFIER    

rlanPppGroup 1.3.6.1.4.1.64.9.24
OBJECT IDENTIFIER    

rlanRemExtGroup 1.3.6.1.4.1.64.9.25
OBJECT IDENTIFIER    

rlanTimeOfDayGroup 1.3.6.1.4.1.64.9.26
OBJECT IDENTIFIER    

rlanDpnssBchGroup 1.3.6.1.4.1.64.9.27
OBJECT IDENTIFIER    

rlanCallRoutingGroup 1.3.6.1.4.1.64.9.28
OBJECT IDENTIFIER    

rlanSecurityGroup 1.3.6.1.4.1.64.9.29
OBJECT IDENTIFIER    

rlanIpRoutingGroup 1.3.6.1.4.1.64.9.30
OBJECT IDENTIFIER    

rSysName 1.3.6.1.4.1.64.9.1.1
Tells you the name allocated to this system.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rSysAdminState 1.3.6.1.4.1.64.9.1.2
Select this option when you want the system to process new calls. If you disable this option, the system will not accept or generate new calls, but existing calls will remain connected. NOTE: Disable during SAP learning mode. Disabling or enabling call processing will not affect the LAN.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rSysTransDelay 1.3.6.1.4.1.64.9.1.4
Enter the maximum frame age (in tenths of a second).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..400  

rSysCallTeardown 1.3.6.1.4.1.64.9.1.6
Select this option when you want the system to tear down all currently active calls.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noTeardown(1), teardown(2)  

rSysNVRAMDiag 1.3.6.1.4.1.64.9.1.7
Tells you whether the system has passed the NVRAM diagnostics. If it failed, the read/write test passed, but at least one of the NVRAM objects failed the startup checksum. If it passed, all the NVRAM objects passed the startup checksum.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER failed(1), passed(2)  

rSysRTCDiag 1.3.6.1.4.1.64.9.1.8
Tells you whether the system's real-time clock is reliable. If the real-time clock has failed the diagnostics, the system is using inaccurate time and date information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER failed(1), passed(2)  

rSysLANDiag 1.3.6.1.4.1.64.9.1.9
Tells you whether the 82596 LAN controller chip passed or failed the LAN diagnostics.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER failed(1), passed(2)  

rSysPromRev 1.3.6.1.4.1.64.9.1.10
Tells you the revision number of the boot PROM.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..16)  

rSysOpState 1.3.6.1.4.1.64.9.1.11
Tells you whether the system is operational (enabled), not operational (disabled) or faulty.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2), faulty(3)  

rSysUpTime 1.3.6.1.4.1.64.9.1.12
Tells you how long (in hundredths of a second) the system has been running since the last reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

rSysTotalRAM 1.3.6.1.4.1.64.9.1.13
Tells you how much RAM has been allocated to the System Controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rSysRSCSlot 1.3.6.1.4.1.64.9.1.14
Tells you the slot position of the RSC 9000 card (System Controller) with respect to the P2 backplane.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rSysCompressionAdminState 1.3.6.1.4.1.64.9.1.15
Select this option when you want the system to use data compression.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rSysCompressionOpState 1.3.6.1.4.1.64.9.1.16
Tells you whether data compression for the system is disabled, enabled, or faulty.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2), faulty(3)  

rSysCLIDSecurity 1.3.6.1.4.1.64.9.1.17
Select this option when you want the system to use CLID security.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rSysCLIDEnforced 1.3.6.1.4.1.64.9.1.18
Select this option when you want the system to accept only incoming calls with a CLID.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rSysIncomingMinBearer 1.3.6.1.4.1.64.9.1.19
Select the minimum bearer capability allowed during an incoming call: 64 Kbps Unrestricted, 56 Kbps Digital, 3100 Hz Audio, or Speech.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER kbps64Unrestrict(1), kbps56Dig(2), audio3100Hz(3), speech(4)  

rSysRLANLearningAdminState 1.3.6.1.4.1.64.9.1.20
Select this option when you want the system to learn remote LANs that use the Gandalf proprietary link protocol and configure them in the database. The system will not learn remote LANs that use PPP as their WAN protocol. Any LANs calling in while this attribute is enabled will be learned and named with Learnt_lanx, where x is the index into the remote LAN list. Most of the information will be taken from a default remote LAN set up in the database. NOTE: Security is at a minimum when this option is enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rSysDateAndTime 1.3.6.1.4.1.64.9.1.21
Enter the current date and time, using the format specified in RFC 1443.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(11)  

rSysReset 1.3.6.1.4.1.64.9.1.22
Select hardReset when you want the System Controller to reset.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noReset(1), hardReset(2)  

rSysPassword 1.3.6.1.4.1.64.9.1.23
Enter the system password for the system's embedded console.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

rSysHubType 1.3.6.1.4.1.64.9.1.24
Tells you the hub type for this system installation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER xpressstack(24), hub48(48), hub132(132)  

rSysRscSoftwareRev 1.3.6.1.4.1.64.9.1.25
Tells you the software revision for the System Controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..16)  

rSysRscHardwareRev 1.3.6.1.4.1.64.9.1.26
Tells you the hardware revision for the System Controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..16)  

rSysCompressionSoftwareRev 1.3.6.1.4.1.64.9.1.27
Tells you the software revision for the System-Controller compression card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..16)  

rSysCompressionHardwareRev 1.3.6.1.4.1.64.9.1.28
Tells you the hardware revision for the System-Controller compression card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..16)  

rSysCompressionPromRev 1.3.6.1.4.1.64.9.1.29
Tells you the revision number of the boot PROM for the System-Controller compression card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..16)  

rSysLongCallThreshold 1.3.6.1.4.1.64.9.1.30
Enter the threshold an active call must exceed (120 - 86340 seconds) before the system generates a potential trap and event alarm. The range is from 2 mins to 23hrs 59 mins. The setting is in seconds so they are in increments of 60.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 120..86340  

rSysLongCallEvents 1.3.6.1.4.1.64.9.1.31
Select this option when you want the system to generate alarms to the event log when a call to a remote LAN exceeds the call threshold you've set (rSysLongCallThreshold).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rSysP1BckPlSize 1.3.6.1.4.1.64.9.1.32
Tells you the size of the P1 backplane that the system is attached to.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 2..5  

rSysRipForwarding 1.3.6.1.4.1.64.9.1.33
Select this option when you want the system to forward the rips learned from its active remote LANs that are doing PPP IPCP. These rips will be forwarded onto the local LAN when enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rSysOverDOSBS 1.3.6.1.4.1.64.9.1.34
Select this option when you want the system to override the DOSBS (Data Over Speech Bearer Services), enabled at IO card ports.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rSysARPProxy 1.3.6.1.4.1.64.9.1.35
Select this option when you want the system to answer ARP request on behalf of a remote address configuered on the protocol list table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rSysIdByCLID 1.3.6.1.4.1.64.9.1.36
Select this option when you want the system to identify a caller from its Calling Line ID (CLID) before the call is answered. This is useful when the remote is to be called back, so the system will reject the call without the caller being charged for the call.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rSysDialBackHoldoff 1.3.6.1.4.1.64.9.1.37
Time delay the system will observe between the time it determines a dialback call is to be placed and the actual outgoing call request. This allows the remote to turn around and be prepared to receive the call back.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..30  

rSysFailedCallRetryHoldoff 1.3.6.1.4.1.64.9.1.38
Period of time after a failed outgoing call attempt the system will ignore request to place a call to the same remote. In Japan, this is used to meet regulatory approvals where no more than 2 failed calls can be placed in a 3 minute time span. Can also be used with dialback to guarantee that the system will not retry an outgoing call if the remote is due to call back. If a switch type is changed to Japanese, then this value will be changed to 61 seconds if it set to a lower value. When a Japanese switch is defined, the minimum acceptable value is 61 seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..120  

rSysCLIDBlacklistAfterAttempts 1.3.6.1.4.1.64.9.1.39
The number of times that a CLID will be allowed to fail until it is blacklisted. The default is one, that is, the first time that a CLID fails, it will be blacklisted. If set to 0, this feature is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..9  

rlanCardTable 1.3.6.1.4.1.64.9.2.1
Lets you view and manage how the system configures individual cards.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanCardEntry

rlanCardEntry 1.3.6.1.4.1.64.9.2.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanCardEntry  

rCardID 1.3.6.1.4.1.64.9.2.1.1.1
Tells you the position of a card (1-10) within the hub with respect to the P2 backplane.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..10  

rCardType 1.3.6.1.4.1.64.9.2.1.1.2
Select the card type for this particular card: mrm9430, bri9308, xsm9516RS232V11, xsm9516RS232V35, pri9360DB15, pri9346DB15, pri9330BNC, pri9330DB15, pri9323DB15, briU9308.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mrm9430(36), vrm9630(40), bri9308(148), xsm9516RS232V11(152), xsm9516RS232V35(156), pri9360DB15(180), pri9346DB15(184), pri9346eDB15(188), pri9330BNC(192), pri9330DB15(196), pri9323DB15(200), pri9360eDB15(204), briU9308(208)  

rCardAdmst 1.3.6.1.4.1.64.9.2.1.1.3
Select this option when you want the system to accept and generate new calls on a card. If you disable this option, existing calls on the card will remain connected, but the system will not accept or generate new calls on the card. DEFAULT = selected
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rCardStatus 1.3.6.1.4.1.64.9.2.1.1.4
Specify whether a card is online or offline. NOTE: If a card is ONLINE and you set it to OFFLINE, all calls on the card will be torn down. DEFAULT = online
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER offline(1), online(2)  

rCardDiag 1.3.6.1.4.1.64.9.2.1.1.5
Tells you whether this card has passed or failed diagnostics.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER failed(1), passed(2)  

rCardOpState 1.3.6.1.4.1.64.9.2.1.1.6
Tells you the operational state of a card, which can be one of: OFFLINE - you've pressed the OFFLINE button on the card or you've set the status of the card (rCardStatus) to OFFLINE. ONLINE - the card is functioning. GONE - the card is not in its slot, but the slot is still configured. FAULTY - the link to the card has been lost, or the card is defective. DETECTED - the card has been detected, but its link to the System Controller has not yet been established. WAITDOWNREQ - the System Controller is waiting for a Download Request to come from the card. DOWNLOADING - the System Controller is downloading the op code to the card. WAITDOWNACK - the download has been completed, and the System Controller is now waiting for an acknowledgement from the card. WAITOPCODE - the card is currently starting up. MISMATCH - the card does not match the definition for it that is stored in the database. CARDEMPTY - the card has been removed from the slot, which is no longer configured. CARDREJECTED - the card has been rejected because it caused the number of channels to exceed the maximum allowed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER cardOffline(1), cardOnline(2), cardGone(3), cardFaulty(4), cardDetected(5), cardWaitDownReq(6), cardDownloading(7), cardWaitDownAck(8), cardWaitOpCode(9), cardMismatch(10), cardEmpty(11), cardRejected(12)  

rCardSWRev 1.3.6.1.4.1.64.9.2.1.1.7
Tells you the software revision for the card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..16)  

rCardHWRev 1.3.6.1.4.1.64.9.2.1.1.8
Tells you the hardware revision for the card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..16)  

rCardTotalRAM 1.3.6.1.4.1.64.9.2.1.1.9
Tells you how much RAM (in bytes) has been allocated to the card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rCardBRISwitch 1.3.6.1.4.1.64.9.2.1.1.10
If this is a BRI9308 card, select the BRI switch type you want it to use: ni1, nt, attPointToPoint, attMultiPoint, net3, or other. If you try to select a BRI switch type for card types other than BRI, you'll see the following error message: noSuchName. DEFAULT = ni 1
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ni1(1), nt(2), attPointToPoint(3), attMultiPoint(4), net3(5), ins64(6), other(7)  

rCardBootProm 1.3.6.1.4.1.64.9.2.1.1.11
Tells you the software revision id of the boot PROM for this card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..16)  

rCardReset 1.3.6.1.4.1.64.9.2.1.1.12
Select hardReset to reset the card. NOTE: The card must be offline to be reset. DEFAULT = noReset
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noReset(1), hardReset(2)  

rCardTearDown 1.3.6.1.4.1.64.9.2.1.1.13
Select this option when you want the system to disconnect all active calls on the card. DEFAULT = noTear Down
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noTearDown(1), tearDown(2)  

rCardRowStatus 1.3.6.1.4.1.64.9.2.1.1.14
The current status of this entry. If the row status is set to destroy(6), the card will be removed from the database only if the card is offline (see the rCardStatus attribute). If the card is not OFFLINE, a BAD_VALUE_ERROR will be returned to the Manager.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

rCardPriActivate 1.3.6.1.4.1.64.9.2.1.1.15
Setting this object to 1 will activate the changes of a PRI card. A read from this object will return a 0 for no action needed, or a 2 for changes pending. 0 and 2 cannot be set.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER noChangesPending(0), activate(1), changesPending(2)  

rlanDChanStatsTable 1.3.6.1.4.1.64.9.3.1
This table provides a management view of the statistics specific to individual D Channels. The port ID is the D-channel ID.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanDChanStatsEntry

rlanDChanStatsEntry 1.3.6.1.4.1.64.9.3.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanDChanStatsEntry  

rDChanCardID 1.3.6.1.4.1.64.9.3.1.1.1
Tells you the position of this card (from 1 to 10) within the hub with respect to the P2 backplane.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..10  

rDChanPortID 1.3.6.1.4.1.64.9.3.1.1.2
Tells you the Port ID of this D Channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..8  

rDChanState 1.3.6.1.4.1.64.9.3.1.1.3
Tells you the administrative status of the Channel or Modem on this I/O card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER linkDown(1), linkUp(2), linkFaulty(3), outOfService1(4), outOfService2(5), outOfService3(6), outOfService4(7), outOfService5(8), modemNotInstalled(9)  

rDChanRxFrames 1.3.6.1.4.1.64.9.3.1.1.4
Tells you how many LAPD frames have been received on this D Channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rDChanRxCRCErrs 1.3.6.1.4.1.64.9.3.1.1.5
Tells you how many LAPD frames with CRC errors have been received on this D Channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rDChanRxOverErrs 1.3.6.1.4.1.64.9.3.1.1.6
Tells you how many frames have been received on this D Channel but discarded because there was not enough memory to store them.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rDChanRxOverflows 1.3.6.1.4.1.64.9.3.1.1.7
Tells you the how many LAPD frames with overflow errors have been received on this D Channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rDChanRxAborts 1.3.6.1.4.1.64.9.3.1.1.8
Tells you how many LAPD frames have been received on this D Channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rDChanRxCalls 1.3.6.1.4.1.64.9.3.1.1.9
Tells you how many calls have been received on this D Channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rDChanTxFrames 1.3.6.1.4.1.64.9.3.1.1.10
Tells you the how many LAPD frames have been transmitted on this D Channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rDChanTxUnderErrs 1.3.6.1.4.1.64.9.3.1.1.11
Tells you how many LAPD frames with underrun errors have been transmitted on this D Channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rDChanTxCalls 1.3.6.1.4.1.64.9.3.1.1.12
Tells you the how many calls have been transmitted on this D Channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rDChanLostDSLs 1.3.6.1.4.1.64.9.3.1.1.13
Tells you how many DSL (digital subscriber loop link) losses have occurred on this D Channel (i.e., how many ISDN connections have been dropped).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rDChanColls 1.3.6.1.4.1.64.9.3.1.1.14
Tells you how many LAPD frames have collided on this D Channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rDChanFrameSlips 1.3.6.1.4.1.64.9.3.1.1.15
Tells you how many LAPD frames have slipped on this D Channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rDChanLinkFaults 1.3.6.1.4.1.64.9.3.1.1.16
Tells you how many link faults (timeouts) have occurred on this D Channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rlanDChanConfigTable 1.3.6.1.4.1.64.9.3.2
This table provides a management view of the system configuration specific to individual D-channels. The port ID is nothing else than the D-channel ID.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanDChanConfigEntry

rlanDChanConfigEntry 1.3.6.1.4.1.64.9.3.2.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanDChanConfigEntry  

rDChanStatus 1.3.6.1.4.1.64.9.3.2.1.1
Specify whether a port should be put OFFLINE or ONLINE. Reading this object always returns online(2) regardless of the card's current operational state. If the port is ONLINE and the attribute is set OFFLINE, all calls on this port will be torn down and the port will be put in the OFFLINE state. To set a port back to ONLINE, select ONLINE from the list of options. DEFAULT = online
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER offline(1), online(2)  

rDChanFaultThreshold 1.3.6.1.4.1.64.9.3.2.1.2
Enter the threshold (1-10000 seconds) that the number of port faults must exceed before the port is taken offline and a potential trap and event alarm is generated. A value of zero disables this function. DEFAULT = 0
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..10000  

rDChanDOSBS 1.3.6.1.4.1.64.9.3.2.1.3
Select this option to enable digital over speech bearer for BRI D-channels.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rDChanBriNetSync 1.3.6.1.4.1.64.9.3.2.1.4
Select whether to source the system clock from this network connection.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), none(3)  

rlanChannelConfigTable 1.3.6.1.4.1.64.9.4.2
This table provides a management view of the system configuration generic parameters specific to individual data-bearing channels (i.e., ISDN B Channels and XSM sync channels, but NOT ISDN D Channels).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanChannelConfigEntry

rlanChannelConfigEntry 1.3.6.1.4.1.64.9.4.2.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanChannelConfigEntry  

rChanCardID 1.3.6.1.4.1.64.9.4.2.1.1
Tells you the position of this card within the hub with respect to the P2 backplane.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..10  

rChanPortID 1.3.6.1.4.1.64.9.4.2.1.2
Tells you which port this channel belongs to on this specific card.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

rChanID 1.3.6.1.4.1.64.9.4.2.1.3
Tells you the channel ID within the port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..31  

rChanOpMode 1.3.6.1.4.1.64.9.4.2.1.4
Select the mode of operation for this channel, which can be one of: Disabled, AnswerCallsOnly; AnswerAndOriginateCalls; OriginateCallsOnly, Leased (PRI port only). If this channel belongs to a BRI port (but not a PRI port), it will set the other B Channel on the BRI port as well, even if this attribute is set for a unique B Channel. A B Channel that belongs to a BRI port supports only the first four values. A badValue error will be returned if a SET request with a value of 'leased' is received on a B Channel that belongs to a BRI port. A B Channel that belongs to a PRI port supports all values from 1 to 5. A B Channel that belongs to a card of type pri9360DB15 or pri9346DB15 supports all values. NOTE: A leased PRI will support only a disabled or leased mode. All values from 1 to 5 are supported on XSM channels. DEFAULT = AnswerAndOriginateCalls
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), answerCallsOnly(2), answerAndOrignateCalls(3), originateCallsOnly(4), leased(5), dropAndInsert(6), dropAndInsertRobbedBit(7)  

rChanChannelGroup 1.3.6.1.4.1.64.9.4.2.1.5
Enter the index for the Channel group this channel belongs to. Setting this value on any channel updates all channels that belong to the same port. DEFAULT = 1
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..65  

rChanHuntGroup 1.3.6.1.4.1.64.9.4.2.1.6
Enter the index for the Hunt group this channel belongs to. Setting this value on any channel updates all channels that belong to the same port. DEFAULT = 1
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..16  

rChanOtherChan 1.3.6.1.4.1.64.9.4.2.1.7
Tells you the corresponding channel that is used if a resource module connection is up. If this is indexed by a Resource Module it will return the ISDN channel used or the Resource Module used if this is a BRI or PRI/DUAL Pri. Note: A return of 0 means that any active call does not include a resource module. Also, there is the possiblility of 64 channels on a card, therefore to find the corresponding channel on numbers returned that are greater than 64, use the following logic: channel is on card X / 64 and is channel X mod 64.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..256  

rlanBriChanConfigTable 1.3.6.1.4.1.64.9.4.3
This table provides a management view of the system configuration generic parameters specific to Basic Rate ISDN B Channels.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanBriChanConfigEntry

rlanBriChanConfigEntry 1.3.6.1.4.1.64.9.4.3.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanBriChanConfigEntry  

rBChanPhoneNum 1.3.6.1.4.1.64.9.4.3.1.1
Enter the telephone number that this B Channel responds to.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

rBChanSPID 1.3.6.1.4.1.64.9.4.3.1.2
Enter the service-profile ID that the Central Office is providing for the B Channel.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..20)  

rlanSerialChanConfigTable 1.3.6.1.4.1.64.9.4.4
This table provides a management view of the system configuration parameters specific to serial channels.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanSerialChanConfigEntry

rlanSerialChanConfigEntry 1.3.6.1.4.1.64.9.4.4.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanSerialChanConfigEntry  

rChanCallCtrl 1.3.6.1.4.1.64.9.4.4.1.1
Select the call-setup/teardown signalling to be used with the attached device, which can be one of: controlSignal or v25bis. If rChanOpMode is set to 'leased', this option is forced to controlSignal (setting it to any other value will generate a bad value error). DEFAULT = v25bis
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER controlSignal(1), v25bis(2)  

rChanHoldOff 1.3.6.1.4.1.64.9.4.4.1.2
Enter the time (in seconds) between a disconnect and the channel's availability to support an outbound call. DEFAULT = 10
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..30  

rChanCallSetupTO 1.3.6.1.4.1.64.9.4.4.1.3
Enter the time (in seconds) for completing call setup that the system allows before timing out. DEFAULT = 30.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 2..120  

rlanSyncChanStatsTable 1.3.6.1.4.1.64.9.4.5
This table provides a management view of the generic statistics for individual, synchronous, data bearing channels (e.g., PRI, BRI and XSM channels).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanSyncChanStatsEntry

rlanSyncChanStatsEntry 1.3.6.1.4.1.64.9.4.5.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanSyncChanStatsEntry  

rSyncChanWANStatsIndex 1.3.6.1.4.1.64.9.4.5.1.1
Tells you the WAN link that's associated with this channel. If this channel is not currently connected, you'll see a value of -1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..128  

rSyncChanLinkState 1.3.6.1.4.1.64.9.4.5.1.2
Tells you the status of the channel's connection, which can be one of: linkDown, LinkUp, or linkFaulty.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER linkDown(1), linkUp(2), linkFaulty(3), linkMdm(9), linkLoading(10), linkLost(11), linkRemoved(12), linkVoice(13), linkPbxPassthru(14)  

rSyncChanRxFrames 1.3.6.1.4.1.64.9.4.5.1.3
Tells you how many HDLC frames this channel has received since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rSyncChanRxOctets 1.3.6.1.4.1.64.9.4.5.1.4
Tells you how many octets this channel has received since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rSyncChanRxFrameErrs 1.3.6.1.4.1.64.9.4.5.1.5
Tells you how many HDLC frames this channel has detected but not successfully received for one of the following reasons: 1) Rxed with Bad CRC 2) Rxed with Overrun errors 3) Rxed aborted frames
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rSyncChanRxCRCErrs 1.3.6.1.4.1.64.9.4.5.1.6
Tells you how many HDLC frames this channel has received but discarded because of a CRC mismatch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rSyncChanRxOverErrs 1.3.6.1.4.1.64.9.4.5.1.7
Tells you how many HDLC frames this channel has received but discarded because there was not enough memory in the system to store them.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rSyncChanRxAborts 1.3.6.1.4.1.64.9.4.5.1.8
Tells you how many HDLC frames this channel has received but discarded because the frame had been aborted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rSyncChanRxShortFrames 1.3.6.1.4.1.64.9.4.5.1.9
Tells you how many HDLC frames this channel has received that were shorter than 4 bytes in length.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rSyncChanRxLongFrames 1.3.6.1.4.1.64.9.4.5.1.10
Tells you how many HDLC frames this channel has received that were longer than 4096 bytes in length.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rSyncChanTxFrames 1.3.6.1.4.1.64.9.4.5.1.11
Tells you how many HDLC frames have been transmitted on this channel since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rSyncChanTxOctets 1.3.6.1.4.1.64.9.4.5.1.12
Tells you how many octets have been transmitted on this channel since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rSyncChanTxFrameErrs 1.3.6.1.4.1.64.9.4.5.1.13
Tells you how many HDLC frames this channel tried to transmit unsuccessfully since the last system reset for one of the following reasons: 1) TXed underrun 2) TXed aborted frames
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rSyncChanTxUnderErrs 1.3.6.1.4.1.64.9.4.5.1.14
Tells you how many HDLC frames this channel tried to transmit unsuccessfully since the last system reset because there was not enough data in memory to transmit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rSyncChanTxAborts 1.3.6.1.4.1.64.9.4.5.1.15
Tells you how many HDLC frames this channel tried to transmit unsuccessfully since the last system reset because the frame had been aborted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rSyncChanLinkFaults 1.3.6.1.4.1.64.9.4.5.1.16
Tells you how many times the WAN protocol has failed since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rSyncChanResourceShorts 1.3.6.1.4.1.64.9.4.5.1.17
Tells you how many resource shortages this channel has experienced since the last system reset. A resource shortage is a condition that occurs when the channel driver runs out of receive buffers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rSyncChanLastResultCode 1.3.6.1.4.1.64.9.4.5.1.18
Tells you the result code from the last call on this channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rSyncChanConnectedPhnum 1.3.6.1.4.1.64.9.4.5.1.19
This is the phone number (or extension number) of the connected party, i.e. at the far end of this B-channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

rSyncChanConnectedName 1.3.6.1.4.1.64.9.4.5.1.20
This is the name of the connected party, i.e. at the far end of this B-channel. This information is sometimes passed over the signalling channel of the network when a call is generated or received, and on these occasions the information is captured and stored here.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

rlanIsdnBChanTable 1.3.6.1.4.1.64.9.4.6
This table provides a management view of the ISDN statistics and configeration for individual B Channels.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanIsdnBChanEntry

rlanIsdnBChanEntry 1.3.6.1.4.1.64.9.4.6.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanIsdnBChanEntry  

rIsdnBChanBearer 1.3.6.1.4.1.64.9.4.6.1.1
Tells you what bearer capability is used for this B Channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER kbps64Unrestrict(1), kbps56Dig(2), audio3100Hz(3), speech(4), idle(5)  

rIsdnBChanLlSpeed 1.3.6.1.4.1.64.9.4.6.1.2
Allows configeration of the leased line speed for this B Channel (only valid on leased lines).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER kbps64Unrestrict(1), kbps56Dig(2)  

rlanSerialChanStatsTable 1.3.6.1.4.1.64.9.4.7
This table provides a management view of the statistics for individual serial channels.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanSerialChanStatsEntry

rlanSerialChanStatsEntry 1.3.6.1.4.1.64.9.4.7.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanSerialChanStatsEntry  

rSerialChanIfType 1.3.6.1.4.1.64.9.4.7.1.1
Tells you the type of physical interface signalling that is used for the attached device, which can be one of: invalidHW, rs232, v35,or v11.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER invalidHW(1), rs232(2), v35(3), v11(4)  

rSerialChanRole 1.3.6.1.4.1.64.9.4.7.1.2
Tells you what role the device that's using this channel is performing: dte - the device is acting as data terminal equipment dce - the device is acting as data circuit-terminating equipment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), dce(2), dte(3)  

rSerialChanCtlSignals 1.3.6.1.4.1.64.9.4.7.1.3
Tells you the control signal state at the interface, which is bit- mapped as follows: Bit RS232 V.35 V.11 --- ----- ---- ---- 0 RTS RTS CTRL 1 CTS CTS IND 2 DSR DSR n/a 3 DCD DCD n/a 4 DTR DTR n/a 5 RI n/a n/a 6 TM n/a n/a 7 LL n/a n/a 8 RL n/a n/a 9 n/a n/a n/a 10 n/a n/a n/a NOTE: Bit zero (0) is the least significant bit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rSerialChanLoopBack 1.3.6.1.4.1.64.9.4.7.1.4
Tells you the type of loopback test the system is running. NOTE: Applies only to rs232 channels.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER noLoopBack(1), localDigLoopBack(2), localAnalogueLoopBack(3), remoteDigitalLoopBack(4)  

rSerialChanInConnects 1.3.6.1.4.1.64.9.4.7.1.5
Tells you how many attempted inbound connects the signalling protocol in effect for this channel has detected since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rSerialChanOutConnects 1.3.6.1.4.1.64.9.4.7.1.6
Tells you how many outbound connects have been attempted on this channel since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rSerialChanOutConnectFails 1.3.6.1.4.1.64.9.4.7.1.7
Tells you how many outbound connects attempted on this channel were not successfully established since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rChannelGroupIdUnused 1.3.6.1.4.1.64.9.4.8
This object is used to identify a potentially unused index that can be used as the rChannelGroupId instance when creating new entries in the rlanChannelGroupTable. A returned value of zero indicates that the table is full.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65  

rlanChannelGroupTable 1.3.6.1.4.1.64.9.4.9
This table provides a management view of the system channel groups.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanChannelGroupEntry

rlanChannelGroupEntry 1.3.6.1.4.1.64.9.4.9.1
The first entry (rChannelGroupId value of one) corresponds to the default entry. This entry cannot be modified or deleted.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanChannelGroupEntry  

rChannelGroupId 1.3.6.1.4.1.64.9.4.9.1.1
Tells you the unique identifier for this row.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65  

rChannelGroupName 1.3.6.1.4.1.64.9.4.9.1.2
Tells you the name of this channel group. Channel group names must be unique and are not case sensitive. You cannot modify the default entry Default.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rChannelGroupStatus 1.3.6.1.4.1.64.9.4.9.1.3
Tells you the current status of this entry. You cannot destroy currently assigned channel groups or the default entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

rlanChannelDiagnosticTable 1.3.6.1.4.1.64.9.4.10
This table is used to force connect or disconnect a channel.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanChannelDiagnosticEntry

rlanChannelDiagnosticEntry 1.3.6.1.4.1.64.9.4.10.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanChannelDiagnosticEntry  

rChanDiagRemLANID 1.3.6.1.4.1.64.9.4.10.1.1
Tells you which remote LAN this channel is to connect to. The remote LAN values are from 1 to 1000 but reading this value will always return 0.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1000  

rChanDiagForce 1.3.6.1.4.1.64.9.4.10.1.2
To tell the system to disconnect this channel, select disconnect from the available settings. When you select connect, the system will try to connect this channel to the remote LAN indicated by rChanDiagRemLANID. NOTE: The configuration for the remote LAN must be a member of this channel's channel group. DEFAULT = statusQuo
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER connect(1), disconnect(2), statusQuo(3)  

rlanHuntGroupTable 1.3.6.1.4.1.64.9.4.11
This table provides a management view of Hunt Groups.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanHuntGroupEntry

rlanHuntGroupEntry 1.3.6.1.4.1.64.9.4.11.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanHuntGroupEntry  

rHuntGroupIndex 1.3.6.1.4.1.64.9.4.11.1.1
Tells you which hunt group you are configuring. The hunt group values are from 1 to 16.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

rHuntGroupName 1.3.6.1.4.1.64.9.4.11.1.2
The name of this Hunt Group.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rHuntGroupPhoneNum 1.3.6.1.4.1.64.9.4.11.1.3
The Phone number of this hunt group. Only printable characters are accepted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

rHuntGroupRowStatus 1.3.6.1.4.1.64.9.4.11.1.4
Tells you the current status of this entry. The only states valid for this object are createAndGo(4) and Destroy(6).
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

rlanPBXChanGroupTable 1.3.6.1.4.1.64.9.4.12
This table provides a management view of PBX Channels.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanPBXChanGroupEntry

rlanPBXChanGroupEntry 1.3.6.1.4.1.64.9.4.12.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanPBXChanGroupEntry  

rPBXChanExtensionNumber 1.3.6.1.4.1.64.9.4.12.1.1
The extension number of this PBX channel
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..8)  

rPBXChanModuleType 1.3.6.1.4.1.64.9.4.12.1.2
The module type of this PBX channel. Cannot be set to none(1),gandalfAnalogPhoneEnd(4)' or gandalfAnalogSwitchEnd(5) .
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), ntSwitchEnd(2), ntPhoneEnd(3), gandalfAnalogPhoneEnd(4), gandalfAnalogSwitchEnd(5), mitelVpm(6)  

rPBXChanPhoneType 1.3.6.1.4.1.64.9.4.12.1.3
The phone type connected to this PBX channel
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER meridian(2), norstar(3)  

rPBXChanEncoding 1.3.6.1.4.1.64.9.4.12.1.4
The type of PCM encoding for this PBX channel
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER uLaw(1), aLaw(2)  

rPBXChanVpmMode 1.3.6.1.4.1.64.9.4.12.1.5
The mode of the Voice Processing Module. The value of 1 is for information only and cannot be set.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER unknown(1), mitelSwitchEnd(2), mitelPhoneEnd(3)  

rlanResourceModuleTable 1.3.6.1.4.1.64.9.4.13
This table provides a management view of the parameters specific to Modem and PBX card channels (i.e., Modems and PBX Ports).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanResourceModuleEntry

rlanResourceModuleEntry 1.3.6.1.4.1.64.9.4.13.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanResourceModuleEntry  

rResourceModuleOffline 1.3.6.1.4.1.64.9.4.13.1.1
The online state of a module. Setting offline will not allow the module to go online. Setting online will enable the module to send and receive calls. Reading this object always returns online(2) regardless of the modules's current operational state.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER offline(1), online(2)  

rResourceModuleLinkstate 1.3.6.1.4.1.64.9.4.13.1.2
The current operational state of the resource module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER offline(1), online(2), downloading(10), linklost(11), notinstalled(12)  

rlanPBXChanNTStatsTable 1.3.6.1.4.1.64.9.4.14
This table provides a statistical view of Norther Telecom type of PBX Channels.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanPBXChanNTStatsEntry

rlanPBXChanNTStatsEntry 1.3.6.1.4.1.64.9.4.14.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanPBXChanNTStatsEntry  

rPBXChanNTVoiceTimingPackets 1.3.6.1.4.1.64.9.4.14.1.1
Tells you how many Voice Timing Packets this link has processed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rPBXChanNTSignalCrcErr 1.3.6.1.4.1.64.9.4.14.1.2
Tells you how many Signal Packets with CRC errors this link has processed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rPBXChanNTInvalidAddress 1.3.6.1.4.1.64.9.4.14.1.3
Tells you how many packets that have V.42 address errors this link has processed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rPBXChanNTSignalRejects 1.3.6.1.4.1.64.9.4.14.1.4
Tells you how many times a voice packet is received before an initialization packet is received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rPBXChanNTMaxRetryErr 1.3.6.1.4.1.64.9.4.14.1.5
Tells you how many times this link has reached maximum retries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rPBXChanNTLostSyncErr 1.3.6.1.4.1.64.9.4.14.1.6
Tells you how many times this link has received a voice packet when it shouldn't, or sent a packet of one type and received an unexpected type of response packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rPBXChanNTNoDataSignal 1.3.6.1.4.1.64.9.4.14.1.7
Tells you how many No Data Signal errors this link has processed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rPBXChanNTAckTimeout 1.3.6.1.4.1.64.9.4.14.1.8
Tells you how many times a packet is sent without receiveing an acknowledgement packet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rPBXChanNTTransLockup 1.3.6.1.4.1.64.9.4.14.1.9
This counter is incremented for every packet that fails to be removed from the transmit buffer. eg. SDS signal not received by the PBX extender.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rPBXChanNTReinitTries 1.3.6.1.4.1.64.9.4.14.1.10
Tells you the number of reinitialization attempts on this link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rPBXChanNTDiscFails 1.3.6.1.4.1.64.9.4.14.1.11
Tells you the number of disconnect failures this link has processed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rPBXChanNTRetrans 1.3.6.1.4.1.64.9.4.14.1.12
This counter increments if there are three retransmission attempts in a row.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rPBXChanNTInternalDisc 1.3.6.1.4.1.64.9.4.14.1.13
Tells you how many times the PBX thinks that the phone is lost. Only applies to the central extender.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rPBXChanNTFatalPanics 1.3.6.1.4.1.64.9.4.14.1.14
Tells you how many fatal panics have occured on this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rPBXChanNTLinkIntegrity 1.3.6.1.4.1.64.9.4.14.1.15
Tells you how many link integrity problems have occured on this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rPBXChanNTRxFails 1.3.6.1.4.1.64.9.4.14.1.16
Tells you how many failed incoming calls have occured on this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rPBXChanNTTxFails 1.3.6.1.4.1.64.9.4.14.1.17
Tells you how many failed outgoing calls have occured on this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rPBXChanNTCallsRx 1.3.6.1.4.1.64.9.4.14.1.18
Tells you how many successful incoming calls have occured on this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rPBXChanNTCallsTx 1.3.6.1.4.1.64.9.4.14.1.19
Tells you how many successful outgoing calls have occured on this port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rlanWANStatsTable 1.3.6.1.4.1.64.9.5.1
This table provides a management view of the system configuration specific to individual WAN links.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanWANStatsEntry

rlanWANStatsEntry 1.3.6.1.4.1.64.9.5.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanWANStatsEntry  

rWANStatsIndex 1.3.6.1.4.1.64.9.5.1.1.1
Tells you which one of the possible 128 WAN links the current statistics apply to. This index is mapped to a specific channel. To find out which WAN link to use, get the rChanWANStatsIndex attribute from the channel group first.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..128  

rWANStatsCardID 1.3.6.1.4.1.64.9.5.1.1.2
Tells you which card this WAN link is using to talk to the currently connected remote LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..11  

rWANStatsPortID 1.3.6.1.4.1.64.9.5.1.1.3
Tells you which port this WAN link is using to talk to the currently connected remote LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..30  

rWANStatsChanID 1.3.6.1.4.1.64.9.5.1.1.4
Tells you which of the 61 possible channels this WAN link is using to talk to the currently connected remote LAN. The number of possible channels will vary depending on card type. For example a BRI has 2 channels/port, a PRI can have up to 61 channels/port (European CEPT) and an XSM has one channel/port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..61  

rWANStatsRemLANID 1.3.6.1.4.1.64.9.5.1.1.5
Tells you which remote LAN this WAN link connects to, by providing the index to be used in the rlanRemLANGroup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1000  

rWANStatsRemLANName 1.3.6.1.4.1.64.9.5.1.1.6
Tells you which remote LAN this WAN link connects to by providing the name of the remote LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..16)  

rWANStatsRxFrames 1.3.6.1.4.1.64.9.5.1.1.7
Tells you how many HDLC frames this WAN link received during the current call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANStatsRxOctets 1.3.6.1.4.1.64.9.5.1.1.8
Tells you how many octets this WAN link received during the current call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANStatsRxFrameErrs 1.3.6.1.4.1.64.9.5.1.1.9
Tells you how many HDLC frames this WAN link detected but did not successfully receive during the current call for one of the following reasons: 1) Rxed with Bad CRC 2) Rxed with Overrun errors 3) Rxed aborted frames
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANStatsRxCRCErrs 1.3.6.1.4.1.64.9.5.1.1.10
Tells you how many HDLC frames this WAN link received but then discarded because of a CRC mismatch during the current call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANStatsRxOverErrs 1.3.6.1.4.1.64.9.5.1.1.11
Tells you how many HDLC frames this WAN link received but then discarded during the current call because there wasn't enough memory in the system to store them.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANStatsRxAborts 1.3.6.1.4.1.64.9.5.1.1.12
Tells you how many HDLC frames this WANlink received but then discarded during the current call because the frame had been aborted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANStatsRatioErrRx 1.3.6.1.4.1.64.9.5.1.1.13
Tells you the ratio of unsuccessfully received HDLC frames to the number of frames that this WAN link detected during the current call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rWANStatsTxFrames 1.3.6.1.4.1.64.9.5.1.1.14
Tells you how many HDLC frames this WAN link transmitted during the current call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANStatsTxOctets 1.3.6.1.4.1.64.9.5.1.1.15
Tells you how many octets this WAN link transmitted during the current call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANStatsTxFrameErrs 1.3.6.1.4.1.64.9.5.1.1.16
Tells you how many HDLC frames this WAN link tried to transmit unsuccessfully during the current call for one of the following reasons: 1) TXed underrun 2) TXed aborted frames
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANStatsTxUnderErrs 1.3.6.1.4.1.64.9.5.1.1.17
Tells you how many HDLC frames this WAN link tried to transmit unsuccessfully during the current call because there wasn't enough data in memory to transmit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANStatsTxAborts 1.3.6.1.4.1.64.9.5.1.1.18
Tells you how many HDLC frames this WAN link tried to transmit unsuccessfully during the current call because the frame had been aborted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANStatsRatioErrTx 1.3.6.1.4.1.64.9.5.1.1.19
Tells you the ratio of unsuccessfully transmitted frames to the number of attempted frame transmissions during the current call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rWANStatsDuration 1.3.6.1.4.1.64.9.5.1.1.20
Tells you how long (in hundredths of a second) the system has accumulated statistics for this WAN link.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

rWANStatsChanSpeed 1.3.6.1.4.1.64.9.5.1.1.21
Tells you the current channel speed in bits per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rWANStatsRemExtID 1.3.6.1.4.1.64.9.5.1.1.22
Tells you which remote Extension this WAN link connects to, by providing the index to be used in the rlanRemExtGroup.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1000  

rWANStatsRemExtName 1.3.6.1.4.1.64.9.5.1.1.23
Tells you which remote Extension this WAN link connects to by providing the name of the remote Extension.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..16)  

rWANStatsRMCardID 1.3.6.1.4.1.64.9.5.1.1.24
Tells you which Resource Module card this WAN link is using to talk to the currently connected remote.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..11  

rWANStatsRMPortID 1.3.6.1.4.1.64.9.5.1.1.25
Tells you which Resource Module port this WAN link is using to talk to the currently connected remote.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..30  

rWANStatsRMChanID 1.3.6.1.4.1.64.9.5.1.1.26
Tells you which Resource Module Channel this WAN link is using to talk to the currently connected remote.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..61  

rlanWANStatsRMChanTable 1.3.6.1.4.1.64.9.5.2
This table provides a management view of the RM channels associated with a call at any time.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanWANStatsRMChanEntry

rlanWANStatsRMChanEntry 1.3.6.1.4.1.64.9.5.2.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanWANStatsRMChanEntry  

rWANStatsRMWanIndex 1.3.6.1.4.1.64.9.5.2.1.1
Tells you which one of the possible 160 real WAN links or 128 virtual the current statistics apply to. This index is mapped to a specific channel. To find out which WAN link to use, get the rChanWANStatsIndex attribute from the channel group first.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..288  

rWANStatsRMChanIndex 1.3.6.1.4.1.64.9.5.2.1.2
Gives the channel index for the particular channel in use by the call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..6  

rWANStatsRMChanCardID 1.3.6.1.4.1.64.9.5.2.1.3
Tells you which Resource Module card this channel is on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..11  

rWANStatsRMChanPortID 1.3.6.1.4.1.64.9.5.2.1.4
Tells you which Resource Module port this channel is on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..30  

rWANStatsRMChanChanID 1.3.6.1.4.1.64.9.5.2.1.5
Tells you which Resource Module Channel this channel is on.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..61  

rWANStatsRMChanConnectedPhnum 1.3.6.1.4.1.64.9.5.2.1.6
This is the phone number (or extension number) of the connected party, i.e. at the far end of this B-channel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

rWANStatsRMChanConnectedName 1.3.6.1.4.1.64.9.5.2.1.7
This is the name of the connected party, i.e. at the far end of this B-channel. This information is sometimes passed over the signalling channel of the network when a call is generated or received, and on these occasions the information is captured and stored here.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..16)  

rWANSumRxFrames 1.3.6.1.4.1.64.9.6.1
Tells you how many frames the system has received since the last reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANSumRxOctets 1.3.6.1.4.1.64.9.6.2
Tells you how many octets the system has received since the last reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANSumRxFrameErrs 1.3.6.1.4.1.64.9.6.3
Tells you how many HDLC frames the system detected since the last reset, but did not successfully receive for one of the following reasons: 1) Rxed with Bad CRC 2) Rxed with Overrun errors 3) Rxed aborted frames
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANSumRxCRCErrs 1.3.6.1.4.1.64.9.6.4
Tells you how many HDLC frames with CRC mismatches the system has received since the last reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANSumRxOverErrs 1.3.6.1.4.1.64.9.6.5
Tells you how many HDLC frames with overrun errors the system has received since the last reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANSumRxAborts 1.3.6.1.4.1.64.9.6.6
Tells you how many aborted HDLC frames the system has received since the last reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANSumTxFrames 1.3.6.1.4.1.64.9.6.7
Tells you how many HDLC frames the system has transmitted since the last reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANSumTxOctets 1.3.6.1.4.1.64.9.6.8
Tells you how many octets the system has transmitted since the last reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANSumTxFrameErrs 1.3.6.1.4.1.64.9.6.9
Tells you how many HDLC frames the system has detected since the last reset that were not successfully received for one of the following 2 reasons: 1) Txed with underrun errors 2) Txed aborted frames
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANSumTxUnderErrs 1.3.6.1.4.1.64.9.6.10
Tells you how many HDLC frames with underrun errors the system has transmitted since the last reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANSumTxAborts 1.3.6.1.4.1.64.9.6.11
Tells you how many frames the system has aborted during transmission since the last reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rWANSumLinkFaults 1.3.6.1.4.1.64.9.6.12
Tells you how many link fault errors have occurred since the last reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANIDUnused 1.3.6.1.4.1.64.9.7.2
This object is used to identify a potentially unused index to be used as the rRemLANID when creating new entries in the rlanRemLANConfigTable. A returned value of zero indicates that the table is full.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1000  

rlanRemLANConfigTable 1.3.6.1.4.1.64.9.7.3
This table provides a management view of the system configuration specific to individual Remote LAN's.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanRemLANConfigEntry

rlanRemLANConfigEntry 1.3.6.1.4.1.64.9.7.3.1
The conceptual row at instance zero is used by the RSC as the default remote LAN configuration. The values defined for this entry are assigned to learned LAN's when the system is in remote LAN learning mode (rSysRLANLearningAdminState is enabled(2)). This entry is also used to change the defaults chosen when manually configuring a new remote LAN either through the embedded console or via SNMP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanRemLANConfigEntry  

rRemLANID 1.3.6.1.4.1.64.9.7.3.1.1
Tells you the index of this remote LAN. A value of 0 indicates the default remote-LAN configuration; that is, this entry is used to determine the default parameters for remote LANs that are dynamically learned.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..1000  

rRemLANName 1.3.6.1.4.1.64.9.7.3.1.2
Enter the name of the current remote LAN. The name can use up to 16 characters but cannot contain spaces. The name must also be unique. It cannot be LOCAL_LAN or begin with LEARNT_LAN. The default entry (instance zero) cannot be modified.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rRemLANOpMode 1.3.6.1.4.1.64.9.7.3.1.3
Tells you the current operational mode of this remote LAN, which can be one of: 1- disabled: the system will not accept calls from this remote LAN or generate calls to this remote LAN 2- answerCallsOnly: the system will only answer calls from this remote LAN. 3- answerAndOriginateCalls: the system will accept and generate calls from/to this remote LAN. 4- originateCallsOnly: the system will only generate calls to this Remote LAN. DEFAULT = answerAndOriginateCalls
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), answerCallsOnly(2), answerAndOriginateCalls(3), callingOnly(4)  

rRemLANOutMinBearer 1.3.6.1.4.1.64.9.7.3.1.4
Select the minimum bearer capability allowed during an outgoing call to a remote LAN when using ISDN services: 64 Kbps Unrestricted, 56 Kbps Digital, 3100 Hz Audio. DEFAULT = kbps64Unrestrict
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER kbps64Unrestrict(1), kbps56Dig(2), audio3100Hz(3)  

rRemLANCompression 1.3.6.1.4.1.64.9.7.3.1.5
Select the type of compression when you want this remote LAN to use.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), any(2), gandalf(3), stacker(4)  

rRemLANWanProtocol 1.3.6.1.4.1.64.9.7.3.1.6
Select the communications protocol you want the system to use when establishing a call to this remote LAN. The table rlanGandalfProtoConfigTable contains additional information when this object is set to gandalfProprietary(1) otherwise the rlanPppConfigTable is to be used when this object is set to ppp(2). NOTE: When you are changing or creating new remote LANs, rRemLANSerialNumber or rRemLANPppSecret for the remote LAN must be present (depending on the setting of the remote LAN) in the same SNMP message. DEFAULT = gandalfProprietary
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER gandalfProprietary(1), ppp(2)  

rRemLANIdleTimeout 1.3.6.1.4.1.64.9.7.3.1.7
Enter how long (in seconds) the connection must be idle before the system decides to disconnect the channel(s). If you enter a value of '0', there is no idle time-out. DEFAULT = 90
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

rRemLANMaxChannels 1.3.6.1.4.1.64.9.7.3.1.8
Enter the maximum number of channels to be connected to a remote LAN.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..2  

rRemLANFlooding 1.3.6.1.4.1.64.9.7.3.1.9
Specify whether or not the system should allow flooding of unknown destination unicast packets to the remote LAN or from this remote LAN to other remote LANs. DEFAULT = to
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER filter(1), to(2), from(3), bi-directional(4)  

rRemLANMCastFwd 1.3.6.1.4.1.64.9.7.3.1.10
Select the multicast packet treatment to be used for this remote LAN. DEFAULT = bi-directional
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER filter(1), to(2), from(3), bi-directional(4)  

rRemLANBCastFwd 1.3.6.1.4.1.64.9.7.3.1.11
Select the broadcast packet treatment to be used for this remote LAN. DEFAULT = bi-directional
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER filter(1), to(2), from(3), bi-directional(4)  

rRemLANCallForce 1.3.6.1.4.1.64.9.7.3.1.12
To tell the system to disconnect this remote LAN, select disconnect from the list of available options. When you select connect, the system will try to connect to the remote LAN on an available channel as specified in the rlanDestAddressConfigTable selection parameters (i.e., channel group) DEFAULT = statusQuo.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER connect(1), disconnect(2), statusQuo(3)  

rRemLANWatchdogSpoofing 1.3.6.1.4.1.64.9.7.3.1.13
Select this option when you want the system to respond to watchdog query packets received from the local LAN by this remote LAN. DEFAULT = disabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rRemLANSAPandRIPSpoofingFiltering 1.3.6.1.4.1.64.9.7.3.1.14
Select this option when you want the system to forward, spoof or filter SAP/RIP requests to this remote LAN. DEFAULT = disabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER forward(1), spoof(2), filter(3)  

rRemLANSAPGroups 1.3.6.1.4.1.64.9.7.3.1.15
A list of indexes into the rlanSAPGroupTable. A single octet value of 1 indicates the 'All' SAP group (any other octets with values will generate a bad value error). Setting this object to an octet string length of zero deletes all previous values and returns this object to its default. If rRemLANSAPandRIPSpoofingFiltering is disabled, this attribute will return a zero length string (attempts to set this attribute to any non-zero length string will generate a bad value error). DEFAULT = 2H
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..5)  

rRemLANStatus 1.3.6.1.4.1.64.9.7.3.1.16
Tells you the current status of this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

rRemLANAroundCorner 1.3.6.1.4.1.64.9.7.3.1.17
Select this option when you want this remote LAN to receive data from another remote LAN.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rRemLANPPPNcpTypes 1.3.6.1.4.1.64.9.7.3.1.18
Select the NCP layer that the system should use when communcating with this remote LAN DEFAULT = BCP and IPCP
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER bcp(1), ipcp(2), bcpandipcp(3), ipxcp(4), bcpandipxcp(5), ipcpandipxcp(6), bcpandipcpandipxcp(7)  

rRemLANHuntGroup 1.3.6.1.4.1.64.9.7.3.1.19
Indicates the huntgroup used by this remote LAN. 1 indicates that no Hunt group is defined for this RemLAN.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..16  

rRemLANMdmAnswer 1.3.6.1.4.1.64.9.7.3.1.20
Select this option when you want this modem to originate or answer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER originate(1), answer(2)  

rRemLANEncryption 1.3.6.1.4.1.64.9.7.3.1.21
Select this option when you want to all data to be encrypted/decrypted to/from this remote LAN.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rRemLANSNASpoofing 1.3.6.1.4.1.64.9.7.3.1.22
Select this option when you want the system to spoof SNA keepalive messages when all links to this remote LAN are down. This feature is only available with the 'Point-of- Sale' version.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rRemLANDialBack 1.3.6.1.4.1.64.9.7.3.1.23
Select this option when you want the system to call right back this remote LAN as soon as it is identified and authenticated.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rRemLANTestPresence 1.3.6.1.4.1.64.9.7.3.1.24
Use this option to trigger a test call to this remote LAN using the supplied phone number. This will result in a trap, either gTestPresenceCallPassed, gTestPresenceCallFailed or gTestPresenceCallNotIssued, depending on the outcome of the call. The phone number string can only contain digits and the letters L (Local), N (National) and I (International) as a prefix character. You cannot modify the default entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rRemLANAllAtOnce 1.3.6.1.4.1.64.9.7.3.1.25
If enabled, once an outgoing call to this remote LAN is required, Xpressway/XpressStack will attempt to bring up the maximum number of channels configured at the same time.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rlanGandalfProtoConfigTable 1.3.6.1.4.1.64.9.7.4
This table contains objects that pertain to the management of remote LANs that use the Gandalf proprietary link protocol.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanGandalfProtoConfigEntry

rlanGandalfProtoConfigEntry 1.3.6.1.4.1.64.9.7.4.1
No default entry at conceptual row zero exists in this table. In short a default rRemLANSerialNumber cannot be used when learning a remote LAN since this parameter is one of the few parameters that is actually learnt during this process.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanGandalfProtoConfigEntry  

rRemLANSerialNumber 1.3.6.1.4.1.64.9.7.4.1.1
Enter the unique serial number of the remote LAN.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(8)  

rlanPppConfigTable 1.3.6.1.4.1.64.9.7.5
This table contains objects that pertain to the management of remote LANs that use the PPP Internet standard link protocol.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanPppConfigEntry

rlanPppConfigEntry 1.3.6.1.4.1.64.9.7.5.1
A default entry at conceptual row zero does exist in this table. The default entry can be used to specify the PPP authentication protocol only.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanPppConfigEntry  

rRemLANPppAuth 1.3.6.1.4.1.64.9.7.5.1.1
Select the authentication protocol the system should use when verifying the identification of the remote LAN. DEFAULT = pap
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER chap(1), pap(2), papSentOnIncoming(3), terminalMode(4), mschap(5)  

rRemLANPppSecret 1.3.6.1.4.1.64.9.7.5.1.2
Tells you the PPP secret for the remote LAN. The PPP identity is the name you entered for the remote LAN (rRemLANName). You cannot modify the default entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..8)  

rRemLANPppNCP 1.3.6.1.4.1.64.9.7.5.1.3
Select the NCP layer that the system should use when communcating with this remote LAN DEFAULT = BCP and IPCP
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER bcp(1), ipcp(2), bcpandipcp(3), ipxcp(4), bcpandipxcp(5), ipcpandipxcp(6), bcpandipcpandipxcp(7)  

rRemLANRemIPAddrHandling 1.3.6.1.4.1.64.9.7.5.1.4
This attribute determines wether the system can accept or override the DNS IP address submitted by a remote system. DEFAULT = accept.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER accept(1), override(2), assign(3)  

rRemLANPPPRemIPAddr 1.3.6.1.4.1.64.9.7.5.1.5
The IP address to assign to remote if rRemLANRemIPAddrHandling is set to assign(3)
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

rRemLANPPPBapHandling 1.3.6.1.4.1.64.9.7.5.1.6
This attribute determines which BAP protocol is used on a remote LAN PPP connection. DEFAULT = bacp_and_mpplus.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), bacp(2), mpplus(3), bacpandmpplus(4)  

rlanDestAddressConfigTable 1.3.6.1.4.1.64.9.7.6
This table contains objects that pertain to the management of remote LAN addressing information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanDestAddressConfigEntry

rlanDestAddressConfigEntry 1.3.6.1.4.1.64.9.7.6.1
For the default rRemLANID entry (conceptual row zero) two defaults exist in this table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanDestAddressConfigEntry  

rDestAddrId 1.3.6.1.4.1.64.9.7.6.1.1
Tells you the unique identifier for this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

rDestPrefix 1.3.6.1.4.1.64.9.7.6.1.2
Enter an index (1 to 33) into the rlanAddressPrefixConfigTable. DEFAULT = 1
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..33  

rDestPhoneNum 1.3.6.1.4.1.64.9.7.6.1.3
Enter the address of this remote LAN (e.g., a phone number). The phone number string can only contain digits and the letters L (Local), N (National) and I (International) as a prefix character. You cannot modify the default entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

rDestChannelGroupId 1.3.6.1.4.1.64.9.7.6.1.4
Enter an index (1 to 65) into the rlanChannelGroupTable. The system uses the selected entry in this table to determine which group of channels to use when it attempts to establish a call to a remote LAN. DEFAULT = 1
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..65  

rDestLANCLID 1.3.6.1.4.1.64.9.7.6.1.5
Enter the primary Calling Line IDentity number presented during an incoming call from this Remote LAN. The CLID must contain all 16 digits. You cannot modify the default entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

rDestLANMdmRequest 1.3.6.1.4.1.64.9.7.6.1.6
Select this option when you want to use a modem for this remote LAN.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rAddrPrefixIdUnused 1.3.6.1.4.1.64.9.7.7
This object is used to identify a potentially unused index that can be used as the rAddrPrefixId instance when creating new entries in the rlanAddressPrefixConfigTable. A returned value of zero indicates that the table is full.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..33  

rlanAddressPrefixConfigTable 1.3.6.1.4.1.64.9.7.8
This table contains objects that pertain to the management of destination address extension prefixes.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanAddressPrefixConfigEntry

rlanAddressPrefixConfigEntry 1.3.6.1.4.1.64.9.7.8.1
The first entry (rAddrPrefixId value of one) corresponds to the default entry. This entry cannot be modified or deleted.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanAddressPrefixConfigEntry  

rAddrPrefixId 1.3.6.1.4.1.64.9.7.8.1.1
Tells you the prefix entry id.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..33  

rAddrPrefixName 1.3.6.1.4.1.64.9.7.8.1.2
Enter the ASCII name that is associated with a prefix entry. The name must be unique and is not case sensitive. You cannot modify the default entry 'None'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rAddrPrefixString 1.3.6.1.4.1.64.9.7.8.1.3
Enter the prefix string that will precede the destination phone number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..40)  

rAddrPrefixStatus 1.3.6.1.4.1.64.9.7.8.1.4
The current status of this entry. Entries that are in use (referenced by an entry in the rlanDestAddressConfigTable) cannot be destroyed. The default entry cannot be destroyed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

rlanRemLANStatsTable 1.3.6.1.4.1.64.9.7.9
This table provides a management view of the system configuration specific to individual Remote Lans.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanRemLANStatsEntry

rlanRemLANStatsEntry 1.3.6.1.4.1.64.9.7.9.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanRemLANStatsEntry  

rRemLANWANStatsIndex 1.3.6.1.4.1.64.9.7.9.1.1
This string of octets is used to indicate active entries in the rlanWANStatsTable entries where each octet represents an index into this table. A null string length indicates that this remote LAN is currently not active (up). If more than one octet is returned then multi-linking is being performed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

rRemLANLastBearer 1.3.6.1.4.1.64.9.7.9.1.2
Tells you which bearer capability was used for the last call to this remote LAN. Connections to remote LANs that were made using XSM channels are reported as xsm(6).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER kbps64Unrestrict(1), kbps56Dig(2), audio3100Hz(3), speech(4), idle(5), xsm(6)  

rRemLANLastFail 1.3.6.1.4.1.64.9.7.9.1.3
Tells you the failure code for the last call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rRemLANLastTime 1.3.6.1.4.1.64.9.7.9.1.4
Tells you the number of TimeTicks that have elapsed since the last connection to this remote LAN. This value resets every time the remote LAN connects to the local LAN. Returns a 0 if a connection has yet to be made.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

rRemLANInCompressedBits 1.3.6.1.4.1.64.9.7.9.1.5
Tells you how many compressed bits have been received from this remote LAN. The system uses this information when calculating the inbound compression ratio.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANInUncompressedBits 1.3.6.1.4.1.64.9.7.9.1.6
Tells you how many uncompressed bits have been received from this remote LAN. The system uses this Information when calculating the inbound compression ratio.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANInFrames 1.3.6.1.4.1.64.9.7.9.1.7
Tells you how many frames (both unicast and non-unicast) have been received from this remote LAN and forwarded to the local LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANInUCastFwds 1.3.6.1.4.1.64.9.7.9.1.8
Tells you how many unicast frames have been received from this remote LAN and forwarded to the local LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANInUCastFilts 1.3.6.1.4.1.64.9.7.9.1.9
Tells you how many frames have been received from this remote LAN and filtered out.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANInMCastFwds 1.3.6.1.4.1.64.9.7.9.1.10
Tells you many multicast frames have been received from this remote LAN and forwarded to the local LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANInMCastFilts 1.3.6.1.4.1.64.9.7.9.1.11
Tells you how many multicast frames have been received from the remote LAN and filtered out.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANInBCastFwds 1.3.6.1.4.1.64.9.7.9.1.12
Tells you how many broadcast frames have been received from the remote LAN and forwarded to the local LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANInBCastFilts 1.3.6.1.4.1.64.9.7.9.1.13
Tells you how many frames have been received from the remote LAN and filtered out.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANOutCompressedBits 1.3.6.1.4.1.64.9.7.9.1.14
Tells you how many compressed bits have been forwarded to the remote LAN. The system uses this information when calculating the outbound compression ratio.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANOutUncompressedBits 1.3.6.1.4.1.64.9.7.9.1.15
Tells you how many uncompressed bits have been forwarded to the remote LAN. The system uses this information when calculating the outbound compression ratio.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANOutFrames 1.3.6.1.4.1.64.9.7.9.1.16
Tells you how many frames (both unicast and non-unicast) have been forwarded to a WAN link assigned to this remote LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANOutUCastFwds 1.3.6.1.4.1.64.9.7.9.1.17
Tells you how many unicast frames have been forwarded to a WAN link assigned to this remote LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANOutMCastFwds 1.3.6.1.4.1.64.9.7.9.1.18
Tells you how many multicast frames have been received from the local LAN and forwarded to the WAN link assigned to this remote LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANOutBCastFwds 1.3.6.1.4.1.64.9.7.9.1.19
Tells you how many broadcast frames received from the local LAN have been forwarded to the remote LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANDiscTrans 1.3.6.1.4.1.64.9.7.9.1.20
Tells you how many frames were queued to be transmitted but then discarded because their transit delay exceeded the maximum limit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANResShorts 1.3.6.1.4.1.64.9.7.9.1.21
Tells you how many frames were queued to be transmitted but then discarded because of an internal resource shortage.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANDuration 1.3.6.1.4.1.64.9.7.9.1.22
Tells you how long this remote LAN has been connected since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

rRemLANRemoteIP 1.3.6.1.4.1.64.9.7.9.1.23
The IP Address of the remote LAN .
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

rRemLANCompressionResetsRx 1.3.6.1.4.1.64.9.7.9.1.24
Tells you how many compression resets we received from the peer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANCompressionResetsTx 1.3.6.1.4.1.64.9.7.9.1.25
Tells you how many compression resets we sent to the peer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rRemLANLocalDecompressionType 1.3.6.1.4.1.64.9.7.9.1.26
Tells you which bearer capability was used for the last call to this remote LAN. Connections to remote LANs that were made using XSM channels are reported as xsm(6).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noCompression(1), anyCompression(2), slmlFZA(3), slmlIPX(4), slmlFZAP(5), slmlFZAPEncrypt(6), slmlEncrypt(7), pppFZA(8), pppFZAP(9), pppFZAPEncrypt(10), pppEncrypt(11), pppStacNone(12), pppStacLCB(13), pppStacCRC(14), pppStacSeq(15), pppStacExt(16), pppAscendLCB(17)  

rRemLANLocalCompressionType 1.3.6.1.4.1.64.9.7.9.1.27
Tells you which bearer capability was used for the last call to this remote LAN. Connections to remote LANs that were made using XSM channels are reported as xsm(6).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noCompression(1), anyCompression(2), slmlFZA(3), slmlIPX(4), slmlFZAP(5), slmlFZAPEncrypt(6), slmlEncrypt(7), pppFZA(8), pppFZAP(9), pppFZAPEncrypt(10), pppEncrypt(11), pppStacNone(12), pppStacLCB(13), pppStacCRC(14), pppStacSeq(15), pppStacExt(16), pppAscendLCB(17)  

rRemLANBcpStatus 1.3.6.1.4.1.64.9.7.9.1.28
Tell you if the BCP Network Control Protocol (NCP) is active for this remote LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

rRemLANIpcpStatus 1.3.6.1.4.1.64.9.7.9.1.29
Tell you if the IPCP Network Control Protocol (NCP) is active for this remote LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

rRemLANIpxcpStatus 1.3.6.1.4.1.64.9.7.9.1.30
Tell you if the IPXCP Network Control Protocol (NCP) is active for this remote LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

rRemLANBacpStatus 1.3.6.1.4.1.64.9.7.9.1.31
Tell you if the PACP Protocol is active for this remote LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

rRemLANMpplusStatus 1.3.6.1.4.1.64.9.7.9.1.32
Tell you if the Mpplus Protocol is active for this remote LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER active(1), inactive(2)  

rRemLANDynamic 1.3.6.1.4.1.64.9.7.9.1.33
Tell you if this remote LAN has been created dynamically
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

rRemLANUserMustAuthenticate 1.3.6.1.4.1.64.9.7.9.1.34
Tell you if this remote LAN must use authentication
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

rRemLANLastConnected 1.3.6.1.4.1.64.9.7.9.1.35
ASCII String of the last time this remote has connected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..80)  

rLocLANAdmst 1.3.6.1.4.1.64.9.8.1
Select the desired state of the local LAN: disabled or enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rLocLANConnector 1.3.6.1.4.1.64.9.8.2
Select the Ethernet interface for the local LAN depending on the Hardware platform: for the 10095 and 8441 boards the choices are AUI or P2. The 10444 boards cannot be changed. NOTE: Changing the Ethernet interface may disconnect any active connections with the system through the LAN port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER aui(1), p2(2)  

rLocLANMACAddress 1.3.6.1.4.1.64.9.8.3
Tells you the MAC address of the local LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

rLocLANOpState 1.3.6.1.4.1.64.9.8.4
Tells you whether the local LAN is disabled, enabled, or faulty.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2), faulty(3)  

rLocLANRxFrames 1.3.6.1.4.1.64.9.8.5
Tells you how many Ethernet frames have been received from the local LAN since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANRxOctets 1.3.6.1.4.1.64.9.8.6
Tells you how many octets have been received from the local LAN since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANRxAlignErrs 1.3.6.1.4.1.64.9.8.7
Tells you how many frames from the local LAN have been lost during reception due to alignment errors since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANRxCRCErrs 1.3.6.1.4.1.64.9.8.8
Tells you how many frames from the local LAN were lost during reception due to CRC errors since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANRxMCasts 1.3.6.1.4.1.64.9.8.9
Tells you how many multicast packets have been received from the local LAN since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANRxBCasts 1.3.6.1.4.1.64.9.8.10
Tells you how many broadcast packets have been received from the local LAN since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANTxFrames 1.3.6.1.4.1.64.9.8.11
Tells you how many frames have been transmitted successfully to the local LAN since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANTxOctets 1.3.6.1.4.1.64.9.8.12
Tells you how many octets have been transmitted successfully to the local LAN since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANTxSingleColls 1.3.6.1.4.1.64.9.8.13
Tells you how many frames have been lost due to single collisions since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANTxMultiColls 1.3.6.1.4.1.64.9.8.14
Tells you how many frames from the local LAN have been lost due to multiple collisions since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANTxErrs 1.3.6.1.4.1.64.9.8.15
Tells you how many frames from the local LAN have been lost during reception due to CRC errors and alignment errors since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANLateColls 1.3.6.1.4.1.64.9.8.16
Tells you how many frames from the local LAN have been lost due to a late collision since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANExcessColls 1.3.6.1.4.1.64.9.8.17
Tells you how many frames this port has tried to transmit unsuccessfully since the last system reset because it was not clear-to-send (CTS) or because the 82596 chip locked and had to reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANTxMCasts 1.3.6.1.4.1.64.9.8.18
Tells you how many multicast packets have been transmitted to the local LAN since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANTxBCasts 1.3.6.1.4.1.64.9.8.19
Tells you how many broadcast packets have been transmitted to the local LAN since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANResShorts 1.3.6.1.4.1.64.9.8.20
Tells you how many frames could not be transmitted to the local LAN since the last system reset due to a lack of memory or other resources.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANCSErrs 1.3.6.1.4.1.64.9.8.21
Tells you how many frames could not be transmitted to the local LAN since the last system reset due to carrier sense errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANProtocolFilterForward 1.3.6.1.4.1.64.9.8.22
Select this if you want LAN Protocol Filtering/forwarding.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER forwardall(1), forwardselected(2), filterselected(3)  

rLocLANProtocolID 1.3.6.1.4.1.64.9.8.23
A list of indexes into the rlanLANProtocolIDTable. Indexes 122-127 are predefined entries in the table: 122 Novell IPX/SPX 8137 123 AppleTalk ARP 80F3 124 AppleTalk 809B 125 Reverse ARP 8035 126 ARP 0806 127 TCP/IP 0800 Indexes 1-121 are reserved for future predefined entry expansion. Indexes 128 and up are user defined entries. If rLocLANProtocolFilterForward is forwardall, this attribute will return a zero length string (attempts to set this attribute to any non-zero length string will generate a bad value error).
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(1..5)  

rLocLANOperatingMode 1.3.6.1.4.1.64.9.8.24
Tells you the mode of operation that the RSC 9002 LAN controller has negociated. Only valid on the 9002 platform.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER eth100basetx(1), eth100baset(2), eth10basetx(3), eth10baset(4)  

rLocLANEthMode 1.3.6.1.4.1.64.9.8.25
This attribute selects the operational mode of the Ethernet physical interfaces. It is only applicable to systems that support 100 Meg Ethernet. An error condition will be returned if 100 Meg Ethernet is not supported. 1- autonegotiate: indicates that the interface will use the auto-negotiation feature from the 802.3u standard to determine link speed. 2- 100baseT_fdx: forces the interface into 100baseTX full duplex mode. 3- 100baseT: forces the interface into 100baseTX mode. 4- 10baseT_fdx: forces the interface into 10baseT full duplex mode. 5- 10baseT: forces the interface into 10baseT mode. DEFAULT = autonegotiate
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER autonegotiate(1), eth100baseTxfdx(2), eth100baseTx(3), eth10baseTfdx(4), eth10baseT(5)  

rLocLANFilterInFrames 1.3.6.1.4.1.64.9.9.1
Tells you how many frames (both unicast and non-unicast) have been received from the local LAN since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANFilterInUCasts 1.3.6.1.4.1.64.9.9.2
Tells you how many valid unicast frames (filtered frames plus forwarded frames) have been received from the local LAN since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANFilterInUCastFwds 1.3.6.1.4.1.64.9.9.3
Tells you how many valid unicast frames have been received from the local LAN and forwarded to the remote LAN since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANFilterInUCastFilts 1.3.6.1.4.1.64.9.9.4
Tells you how many valid unicast frames have been received from the local LAN but filtered out since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANFilterInMCasts 1.3.6.1.4.1.64.9.9.5
Tells you how many valid multicast frames (filtered frames and forwarded frames) have been received from the local LAN since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANFilterInMCastFwds 1.3.6.1.4.1.64.9.9.6
Tells you how many valid multicast frames have been received from the local LAN and forwarded to the remote LAN since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANFilterInMCastFilts 1.3.6.1.4.1.64.9.9.7
Tells you how many valid multicast frames have been received from the local LAN but filtered out since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANFilterInBCasts 1.3.6.1.4.1.64.9.9.8
Tells you how many valid broadcast frames (filtered frames and forwarded frames) have been received from the local LAN since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANFilterInBCastFwds 1.3.6.1.4.1.64.9.9.9
Tells you how many valid broadcast frames have been received from the local LAN and forwarded to the remote LAN since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANFilterInBCastFilts 1.3.6.1.4.1.64.9.9.10
Tells you how many valid broadcast frames have been received from the local LAN and filtered out since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANFilterDiscTrans 1.3.6.1.4.1.64.9.9.11
Tells you how many frames have been queued to be transmitted but discarded because their transit delay exceeded the maximum since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rLocLANFilterResShorts 1.3.6.1.4.1.64.9.9.12
Tells you how many frames have been queued to be transmitted but discarded due to a shortage of internal resource(s) since the last system reset.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rFilterCfgLocAgingTime 1.3.6.1.4.1.64.9.10.1
Enter the length of time (in seconds) a station entry for a local LAN that has become inactive should remain in the filter table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 10..999999  

rFilterCfgRemAgingTime 1.3.6.1.4.1.64.9.10.2
Enter the length of time (in seconds) a station entry for a remote LAN that has become inactive should remain in the filter table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 10..999999  

rFilterCfgAgingState 1.3.6.1.4.1.64.9.10.3
Choose to disable or enable dynamic aging of station entries from the filter table.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rFilterCfgBlockRoam 1.3.6.1.4.1.64.9.10.4
Choose to disable or enable block roaming.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rlanMACFilterTable 1.3.6.1.4.1.64.9.11.1
This table provides a management view of the system configuration specific to individual MAC addresses. The table is indexed using the physical address (MAC address).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanMACFilterEntry

rlanMACFilterEntry 1.3.6.1.4.1.64.9.11.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanMACFilterEntry  

rMACID 1.3.6.1.4.1.64.9.11.1.1.1
Tells you the MAC address of one entry in the filter table.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

rMACType 1.3.6.1.4.1.64.9.11.1.1.2
Enter the MAC address type, which can be one of the following: 1- dynamic - the MAC address was learned and is subject to age out if aging is enabled. 2- static - the MAC address was manually entered in the system through the console or SNMP 3- blocked - the system will filter this MAC address. 4- invalid - used to delete MAC filter entries. NOTE: You can create or set a MAC address with a dynamic type. That MAC address will simply be subject to aging as soon as it's created or modified.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER dynamic(1), static(2), blocked(3), invalid(254)  

rMACHomePort 1.3.6.1.4.1.64.9.11.1.1.3
Enter the id for the remote LAN associated with this MAC address. 1) A rMACHomePort with a value of 0 means that the MAC address resides on the local LAN. 2) A rMACHomePort with a value from 1 to 1000 will map to the rRemLANID attribute of 1 to 1000. This attribute cannot be SET alone. A GEN_ERROR will be returned. If you want to change the home port on which the MAC resides, you have to delete by setting rMACType to INVALID and then recreate the entry by having all the attributes in the same SET-REQUEST packet with valid values. NOTE: If you want to create a new MAC entry, you have to make sure that the rMACHomePort attribute that you use has already been created and is, therefore, known by the system.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1000  

rTCPIPAddress 1.3.6.1.4.1.64.9.12.2
Enter the IP address of your system.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

rTCPIPSubMask 1.3.6.1.4.1.64.9.12.3
Enter the subnet mask.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

rTCPIPDefGw 1.3.6.1.4.1.64.9.12.4
Enter the IP address of the default gateway.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

rlanTelnetGroup 1.3.6.1.4.1.64.9.12.5
OBJECT IDENTIFIER    

rTelnetAccess 1.3.6.1.4.1.64.9.12.5.1
Choose to disable or enable the acceptance of an incoming TELNET connection.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rTelnetIpAddr 1.3.6.1.4.1.64.9.12.5.2
Enter the IP address of an acceptable host for a TELNET connection.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

rTelnetIpSubMask 1.3.6.1.4.1.64.9.12.5.3
Enter the mask to be used when an incoming Telnet request is being processed. The source IP address is masked with this attribute and compared to the rTelnetIpAddr attribute for access privileges.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

rFtpByteCount 1.3.6.1.4.1.64.9.12.6
Tells you how many bytes have been transferred during a file transfer that is in process. If no file transfer is in process, the field will display a value zero (0).
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

rFtpInProgress 1.3.6.1.4.1.64.9.12.7
Tells you if a file transfer is progress.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER fxFinished(1), fxInProgress(2)  

rFtpLastResultCode 1.3.6.1.4.1.64.9.12.8
Tells you the Last Result Code for the last file transfer that took place.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER successful(1), aborted(2), invalidId(3), invalidPwd(4), invalidFile(5), invalidCRC(6), invalidVersion(7), noResponseByHost(8), fileAccessError(9), noFlashAvail(10), badFlash(11), flashInUse(12), fxInProgress(13)  

rFtpConfigTable 1.3.6.1.4.1.64.9.12.9
These objects manage the system's embedded ftp client and can be used to initiate file transfers to or from a specified ftp server.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RFtpConfigEntry

rFtpConfigEntry 1.3.6.1.4.1.64.9.12.9.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RFtpConfigEntry  

rFtpFileId 1.3.6.1.4.1.64.9.12.9.1.1
Tells you the file ID for this entry, which can be code, database or auditRecords.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER code(1), database(2), auditRecords(3)  

rFtpServerIpAddr 1.3.6.1.4.1.64.9.12.9.1.2
Enter the IP address of the FTP server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

rFtpClientId 1.3.6.1.4.1.64.9.12.9.1.3
Enter the user ID to be used when the system identifies its embedded FTP client to the FTP server. You must enter this information when you issue a set for code(1) or database(2) file transfers.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rFtpClientPasswd 1.3.6.1.4.1.64.9.12.9.1.4
Enter the user password to be used when the sytem identifies its embedded FTP client to the FTP server. You must enter this information when you issue a set for code(1) or database(2) file transfers.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

rFtpFilePath 1.3.6.1.4.1.64.9.12.9.1.5
Enter the directory path on the FTP server that the file is to be copied to/from.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..80)  

rFtpFileName 1.3.6.1.4.1.64.9.12.9.1.6
Enter the filename to be used when the file is saved on the FTP server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..20)  

rFtpOperation 1.3.6.1.4.1.64.9.12.9.1.7
Select the operation the RSC should perform: get, put, or setup. The get(1) operation is allowed on code and database records. The put(2) operation is allowed on database files and audit records. The setup(3) operation is allowed on all records, which commits the parameters to non-volatile storage. Setting this object to either get(1) or put(2) initiates a file transfer that will be trapped on completion. The get and put operations also perform an implied commit to non-volatile storage. DEFAULT = setup
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER get(1), put(2), setup(3)  

rTCPIPDynamicIP 1.3.6.1.4.1.64.9.12.10
Enter the start IP address of the dynamic IP pool.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

rTCPIPNumDynIp 1.3.6.1.4.1.64.9.12.11
Enter the number of dynamic IPs in the pool.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER 0..150  

rlanBlacklistTable 1.3.6.1.4.1.64.9.13.1
This table provides a management view of the system configuration specific to individual blacklisted phone numbers.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanBlacklistEntry

rlanBlacklistEntry 1.3.6.1.4.1.64.9.13.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanBlacklistEntry  

rBlacklistID 1.3.6.1.4.1.64.9.13.1.1.1
Tells you the ID of any of the possible 64 blacklisted entries.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..64  

rBlacklistCLID 1.3.6.1.4.1.64.9.13.1.1.2
Tells you the blacklisted phone number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rBlacklistStatus 1.3.6.1.4.1.64.9.13.1.1.3
Tells you the current status of this blacklisted entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

rBlacklistIDUnused 1.3.6.1.4.1.64.9.13.2
Identifies a potentially unused index that can be used as the rBlacklistID instance when you're creating new entries in the rlanBlacklistTable. A returned value of zero indicates that the table is full.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..64  

rlanProtocolTable 1.3.6.1.4.1.64.9.14.1
This table provides a management view of the system configuration specific to network addresses. The table is indexed using the network IP address.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanProtocolEntry

rlanProtocolEntry 1.3.6.1.4.1.64.9.14.1.1
Once an entry has been created it cannot be modified. It must be deleted first.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanProtocolEntry  

rProtocolID 1.3.6.1.4.1.64.9.14.1.1.1
Tells you the network address of one entry in the protocol table. It represents a unique device attached to the associated home port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  NetworkAddress  

rProtocolMask 1.3.6.1.4.1.64.9.14.1.1.2
Tells you the network mask associated with this unique entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  NetworkAddress  

rProtocolRemLANID 1.3.6.1.4.1.64.9.14.1.1.3
Tells you the ID of the remote LAN associated with this network address. The value maps one- to-one to the value for the attribute rRemLANID.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..1000  

rProtocolType 1.3.6.1.4.1.64.9.14.1.1.4
Enter the network-address type associated with this unique entry. DEFAULT = ip
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ip(1)  

rProtocolStatus 1.3.6.1.4.1.64.9.14.1.1.5
Tells you the current status of this protocol entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

rlanPriPortTable 1.3.6.1.4.1.64.9.15.1
This table provides a management view of the system configuration specific to individual PRI Ports.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanPriPortEntry

rlanPriPortEntry 1.3.6.1.4.1.64.9.15.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanPriPortEntry  

rPortCardID 1.3.6.1.4.1.64.9.15.1.1.1
Tells you the position of this card within the hub with respect to the P2 backplane. Each PRI card can take slot position 1 to 10.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..10  

rPortPortID 1.3.6.1.4.1.64.9.15.1.1.2
Tells you the port ID for a specific interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

rPortCardType 1.3.6.1.4.1.64.9.15.1.1.3
Tells you the card type to which this port belongs, which can be one of pri9360DB15, pri9346DB15, pri9330BNC, pri9330DB15, pri9323DB15.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER pri9360DB15(180), pri9346DB15(184), pri9346eDB15(188), pri9330BNC(192), pri9330DB15(196), pri9323DB15(200), pri9360eDB15(204)  

rPortLineFormat 1.3.6.1.4.1.64.9.15.1.1.4
Select the line format to be used by a PRI port, which can be one of naDS1ESF, naDS1D4, naDS1D4B8ZS, euroCEPT, euroCEPTCRC4. The first three are North American; the last two are European.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER naDS1ESF(1), naDS1D4(2), euroCEPT(3), euroCEPTCRC4(4), naDS1D4B8ZS(5)  

rPortPRISwitch 1.3.6.1.4.1.64.9.15.1.1.5
Select the switch type to which this PRI port connects, which can be one of att4ESS, att5ESS, ntDMS100, ntDMS250, leased, dass2, dass15, euroisdn, kdd. NOTE: The dass15 switch type is valid only if the timeslot is less than 16; any B channels above timeslot 16 will be invalid.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER att4ESS(1), att5ESS(2), ntDMS100(3), ntDMS250(4), leased(5), dass2(6), dass15(7), euroisdn(8), austel(9), euroisdn-no-restarts(10), euroisdn-numeris(11), ins64(12), passThrough(13), robbedBit(14), ni2(15), ni2LowLow(16), dpnss-a(17), dpnss-b(18), other1(249), other2(250), other3(251), other4(252), other5(253), other6(254)  

rPortDChanFormat 1.3.6.1.4.1.64.9.15.1.1.6
Select the format of the D Channel to be used by this port, which can be one of 64 Kbps, 64 Kbps inverted or 56 Kbps. European standards allow only 64kbps inverted. NOTE: This attribute is applicable only if the port is not leased. If the port is leased, a get or set will generate a noSuchName error. The system will skip this port if the previous attribute has initiated a get-next.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER kbps64(1), kbps64Inverted(2), kbps56(3)  

rPortDChanTimeslot 1.3.6.1.4.1.64.9.15.1.1.7
Enter the timeslot to be used by the D channel. Valid timeslots for the various switch types are: North American: 1..24 European: 1..31 DASS2-15: 1..16 NOTE: This attribute is applicable only if the port is not leased. If the port is leased, a get or set will generate a noSuchName error. The system will skip this port if the previous attribute has initiated a get-next.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..31  

rPortYellowAlarm 1.3.6.1.4.1.64.9.15.1.1.8
Tells you if the YELLOW alarm is off or on. If it's on, the network cannot synchronize itself with the data transmitted by the PRI port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

rPortAISAlarm 1.3.6.1.4.1.64.9.15.1.1.9
Tells you if the AIS alarm is off or on. If it's on, the network cannot accept calls.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

rPortRedAlarm 1.3.6.1.4.1.64.9.15.1.1.10
Tells you if the RED alarm is off or on. If it's on, the PRI port has failed to synchronize with the received data.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER off(1), on(2)  

rPortPhoneNumber 1.3.6.1.4.1.64.9.15.1.1.11
Tells you the phone number that this port answers for. NOTE: This attribute is applicable only if the port is not leased. If the port is leased, a get or set will generate a noSuchName error. The system will skip this port if the previous attribute has initiated a get-next.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

rPortAdmst 1.3.6.1.4.1.64.9.15.1.1.12
Select this option to enable a port. If a port is disabled, current calls won't be torn down, but the port will not accept or originate subsequent calls. If the port is enabled, it will both accept and originate calls. DEFAULT = enabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rPortDLinkNum 1.3.6.1.4.1.64.9.15.1.1.13
Indicates which port this D channel resides on.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..2  

rPortIfId 1.3.6.1.4.1.64.9.15.1.1.14
The identifier of the interface of interest.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..31  

rPortDOSBS 1.3.6.1.4.1.64.9.15.1.1.15
Select this option to enable digital over speech bearer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rPortHuntGroup 1.3.6.1.4.1.64.9.15.1.1.16
Indicates the huntgroup used by this remote LAN. 1 indicates that no Hunt group is defined for this port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..16  

rPortHoldOff 1.3.6.1.4.1.64.9.15.1.1.17
Enter the time (in seconds) between a leased line failure and the time before a reconnection is tried. DEFAULT = 10
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..30  

rPortNetsync 1.3.6.1.4.1.64.9.15.1.1.18
Select whether to source the system clock from this network connection.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), none(3)  

rPortPBXType 1.3.6.1.4.1.64.9.15.1.1.19
Select the type of PBX attached to the port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), mitelSx2000(2), gptIsdx(3)  

rPortIsdnRoutingTable 1.3.6.1.4.1.64.9.15.2
This table provides a management view of the call routing table specific to a PRI port connected to an ISDN network.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanPortIsdnRoutingEntry

rPortIsdnRoutingEntry 1.3.6.1.4.1.64.9.15.2.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanPortIsdnRoutingEntry  

rPortIsdnRouting 1.3.6.1.4.1.64.9.15.2.1.1
Enter the index number of the rIsdnDDIRoutingTable associated with this port. Selecting none (0) forces the call type to be determined in-band. DEFAULT = 0
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..4  

rPortPBXRoutingTable 1.3.6.1.4.1.64.9.15.3
This table provides a management view of the call routing table specific to a PRI port connected to a PBX.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanPortPBXRoutingEntry

rPortPBXRoutingEntry 1.3.6.1.4.1.64.9.15.3.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanPortPBXRoutingEntry  

rPortPBXRouting 1.3.6.1.4.1.64.9.15.3.1.1
Enter the index number of the rPbxCallRoutingTable associated with this port. Selecting none (0) forces the call type to be determined in-band. DEFAULT = 0
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..4  

rIPXWatchdogSpoofing 1.3.6.1.4.1.64.9.16.1
Select this option to enable watchdog spoofing from the local LAN.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rIPXWatchdogSpoofingTimer 1.3.6.1.4.1.64.9.16.2
Enter the length of time ( in seconds) that spoofing should continue.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..99999  

rIPXSAPLearning 1.3.6.1.4.1.64.9.16.3
Tell the system whether it should learn SAPs. When you want the system to learn SAPs, select one of: start-keep-static - Static entries are saved start-drop-static - Static entries are deleted NOTE: You can enable learning only when bridging is disabled and no calls are active.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER stop-learning(1), start-keep-static(2), start-drop-static(3)  

rIPXSAPLearningOPState 1.3.6.1.4.1.64.9.16.4
Tells you whether or not the system is in SAP learning mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rIPXLearntSAPs 1.3.6.1.4.1.64.9.16.5
Tells you how many SAP the system has learned since the last learned mode was enabled.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rlanSAPTable 1.3.6.1.4.1.64.9.17.1
The IPX Service Advertisement Protocol table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanSAPEntry

rlanSAPEntry 1.3.6.1.4.1.64.9.17.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanSAPEntry  

rSAPServiceType 1.3.6.1.4.1.64.9.17.1.1.1
Tells you the type of service that this server provides at this socket. For example: 01h = user 04h = file server 07h = printer server 27h = TCP/IP gateway
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

rSAPServerName 1.3.6.1.4.1.64.9.17.1.1.2
Tells you the name of the server.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(48)  

rSAPType 1.3.6.1.4.1.64.9.17.1.1.3
Select the option that indicates how this entry was learned (dynamic or static). DEFAULT = static
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER dynamic(1), static(2)  

rSAPNetworkAddress 1.3.6.1.4.1.64.9.17.1.1.4
Enter the network address of the server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(4)  

rSAPNodeAddress 1.3.6.1.4.1.64.9.17.1.1.5
Enter the 48-bit node address of the server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(6)  

rSAPSocketAddress 1.3.6.1.4.1.64.9.17.1.1.6
Enter the socket address of the server. For example, 04 53 = Routing Info Protocol.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

rSAPHops 1.3.6.1.4.1.64.9.17.1.1.7
Enter the number of routers to go through to reach the specified server.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

rSAPGroup 1.3.6.1.4.1.64.9.17.1.1.8
Enter the SAP group that this entry belongs to.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 2..34  

rSAPStatus 1.3.6.1.4.1.64.9.17.1.1.9
The current status of this SAP entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

rSAPGroupIdUnused 1.3.6.1.4.1.64.9.17.2
This object is used to identify a potentially unused index that can be used as the rSAPGroupId instance when creating new entries in the rlanSAPGroupTable. A returned value of zero indicates that the table is full.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..34  

rlanSAPGroupTable 1.3.6.1.4.1.64.9.17.3
This table provides an administrative view of the SAP group table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanSAPGroupEntry

rlanSAPGroupEntry 1.3.6.1.4.1.64.9.17.3.1
Each entry in this table is a SAP group name. Each name is used to group learned (and static) IPX services together to form a SAP group. This group can then be assigned to a remote LAN that is interested in this grouping of IPX services. Two default entries exist in this table which cannot be modified or deleted. A rSAPGroupId value of 1 corresponds to the 'All' SAP group, a rSAPGroupId value of 2 corresponds to the 'Default' SAP group. All learned IPX services in the SAP table default to the 'Default' group and all IPX services logically belong to the 'All' group.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanSAPGroupEntry  

rSAPGroupId 1.3.6.1.4.1.64.9.17.3.1.1
Tells you the index of the entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..34  

rSAPGroupName 1.3.6.1.4.1.64.9.17.3.1.2
Enter the identifier for this SAP group. NOTE: SAP group names must be unique, but they're not case sensitive. You cannot modify the two default entries (All and Default).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rSAPGroupStatus 1.3.6.1.4.1.64.9.17.3.1.3
Enter the current status of this entry. NOTE: Entries that are currently in use (e.g., either referenced by a remote LAN or in the rlanSAPTable) cannot be destroyed. The default entries 'All' and 'Default' cannot be destroyed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

rlanRIPTable 1.3.6.1.4.1.64.9.18.1
The IPX Routing Information Protocol table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanRIPEntry

rlanRIPEntry 1.3.6.1.4.1.64.9.18.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanRIPEntry  

rRIPNetworkAddress 1.3.6.1.4.1.64.9.18.1.1.1
Tells you the network address of this route.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4)  

rRIPHops 1.3.6.1.4.1.64.9.18.1.1.2
Tells you the number of routers to go through before reaching this network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..15  

rRIPTicks 1.3.6.1.4.1.64.9.18.1.1.3
Tells you how long (in time-ticks) it takes to reach this network.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

rRIPMACAddress 1.3.6.1.4.1.64.9.18.1.1.4
Tells you the physical (MAC) address of the remote LAN.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PhysAddress  

rlanSnmpSetStatus 1.3.6.1.4.1.64.9.19.1
This object records the result code of the last SNMP set operation. On a set that fails this object can be retrieved to enhance the error codes provided by the SNMP protocol. If the set response contains a non zero error index then this object relates to the object in the set request as indicated by the error index (as per normal PDU error parsing). If the set response message indicates an error but the error index is zero then this object pertains to the semantics of the attempted set operation on the system as as whole (e.g. table full).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER noError(1), internalError(2), badInstance(3), dupName(4), tableFull(5), notFound(6), badValue(7), setError(8), getError(9), createError(10), deleteError(11), dupXID(12), linkUp(13), linkDown(14), offline(15), outCallFail(16), badName(17), noFlash(18), badVersion(19), enabledError(20), inUse(21), tooFew(22), cannotModify(23), sapLearning(24), noIpxRoute(25)  

rSnmpCommunityIndexUnused 1.3.6.1.4.1.64.9.19.2
This object is used to identify a potentially unused index that can be used as the rSnmpCommunityIndex instance when creating new entries in the rlanSnmpCommunityTable. A returned value of zero indicates that the table is full.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..5  

rlanSnmpCommunityTable 1.3.6.1.4.1.64.9.19.3
This table provides a management view of which device can poll this resource via SNMP based on the Community Name, IP address, Privilege and MIB view.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanSnmpCommunityEntry

rlanSnmpCommunityEntry 1.3.6.1.4.1.64.9.19.3.1
This is a list of attributes that make the Community Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanSnmpCommunityEntry  

rSnmpCommunityIndex 1.3.6.1.4.1.64.9.19.3.1.1
Tells you the index entry of this community.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..5  

rSnmpCommunityName 1.3.6.1.4.1.64.9.19.3.1.2
Tells you the name of a community supported by this SNMP agent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rSnmpCommunityIpAddr 1.3.6.1.4.1.64.9.19.3.1.3
Enter the IP address of a manager associated with a community that will be supported by the SNMP agent. NOTE: A value of zero means that all managers from that community will be supported.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

rSnmpCommunityPriv 1.3.6.1.4.1.64.9.19.3.1.4
Enter the access privilege associated with this community, which can be one of none, readOnly, or readWrite. DEFAULT = readOnly
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), readOnly(2), readWrite(3)  

rSnmpCommunityViewIndex 1.3.6.1.4.1.64.9.19.3.1.5
Enter the identifier for the MIB view that is visible to this community. DEFAULT = 2
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..4  

rSnmpCommunityRowStatus 1.3.6.1.4.1.64.9.19.3.1.6
Enter the current status of this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

rSnmpTrapCommunityIndexUnused 1.3.6.1.4.1.64.9.19.4
This object is used to identify a potentially unused index that can be used as the rSnmpTrapCommunityIndex instance when creating new entries in the rlanSnmpTrapCommunityTable. A returned value of zero indicates that the table is full.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..5  

rlanSnmpTrapCommunityTable 1.3.6.1.4.1.64.9.19.5
This table provide a management view of which device(s) (i.e., LAN Managers) this resource will send traps to.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanSnmpTrapCommunityEntry

rlanSnmpTrapCommunityEntry 1.3.6.1.4.1.64.9.19.5.1
This is a list of attributes that make the trap community table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanSnmpTrapCommunityEntry  

rSnmpTrapCommunityIndex 1.3.6.1.4.1.64.9.19.5.1.1
Tells you the index of this community entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..5  

rSnmpTrapCommunityName 1.3.6.1.4.1.64.9.19.5.1.2
Enter the name of a trap community associated with a LAN manager.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rSnmpTrapIpAddr 1.3.6.1.4.1.64.9.19.5.1.3
Enter the IP address of a manager that will receive traps generated by this SNMP agent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

rSnmpTrapRemotePort 1.3.6.1.4.1.64.9.19.5.1.4
Enter the remote UDP port number used by an agent to receive traps. DEFAULT = 162
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

rSnmpTrapStatus 1.3.6.1.4.1.64.9.19.5.1.5
Enter the current status of this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

rSnmpViewNameIndexUnused 1.3.6.1.4.1.64.9.19.6
This object is used to identify a potentially unused index that can be used as the rSnmpViewNameIndex instance when creating new entries in the rlanSnmpViewNameTable. A returned value of zero indicates that the table is full.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..4  

rlanSnmpViewNameTable 1.3.6.1.4.1.64.9.19.7
The table is contained in the local database which defines local MIB views. Reference RFC 1647 for details on MIB views. This table has been adopted from RFC 1647 to an SNMPv1 environment however the logic is the same.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanSnmpViewNameEntry

rlanSnmpViewNameEntry 1.3.6.1.4.1.64.9.19.7.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanSnmpViewNameEntry  

rSnmpViewNameIndex 1.3.6.1.4.1.64.9.19.7.1.1
Tells you the index identifier of the name entry for this MIB view. NOTE: MIB view indexes one(1) and two(2) are statistically configured and cannot be modified.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

rSnmpViewName 1.3.6.1.4.1.64.9.19.7.1.2
Enter the ASCII name assigned to this MIB view.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rSnmpViewNameStatus 1.3.6.1.4.1.64.9.19.7.1.3
Enter the current status of this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

rlanSnmpViewTable 1.3.6.1.4.1.64.9.19.8
The table is contained in the local database which defines local MIB views. Reference RFC 1647 for details on MIB views. This table has been adopted from RFC 1647 to a SNMPv1 enironment however the logic is the same.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanSnmpViewEntry

rlanSnmpViewEntry 1.3.6.1.4.1.64.9.19.8.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanSnmpViewEntry  

rSnmpViewSubtree 1.3.6.1.4.1.64.9.19.8.1.1
Identifies a MIB subtree.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

rSnmpViewMask 1.3.6.1.4.1.64.9.19.8.1.2
The bit mask which, in combination with the corresponding instance of viewSubtree, defines a family of view subtrees. Each bit of this bit mask corresponds to a sub- identifier of viewSubtree, with the most significant bit of the i-th octet of this octet string value (extended if necessary, see below) corresponding to the (8*i - 7)-the sub-identifier, and the least significant bit of the i-th octet of this octet string corresponding to the (8*i)-th sub-identifier, where i is in the range 1 through 16. Each bit of this bit mask specifies whether or not the corresponding sub-identifiers must match when determining if an OBJECT IDENTIFIER is in this family of view subtrees; a '1' indicates that an exact match must occur; a '0' indicates 'wild card', i.e., any sub-identifier value matches. Thus, the OBJECT IDENTIFIER X of an object instance is contained in a family of view subtrees if the following criteria are met: for each sub-identifier of the value of viewSubtree, either: the i-th bit of viewMask is 0, or the i-th sub-identifier of X is equal to the i-th sub-identifier of the value of viewSubtree. If the value of this bit mask is M bits long and there are more than M sub-identifiers in the corresponding instance of viewSubtree, then the bit mask is extended with 1's to be the required length. Note that when the value of this object is the zero-length string, this extension rule results in a mask of all-1's being used (i.e., no 'wild card'), and the family of view subtrees is the one view subtree uniquely identified by the corresponding instance of viewSubtree.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..4)  

rSnmpViewType 1.3.6.1.4.1.64.9.19.8.1.3
The status of a particular family of view subtrees within the particular SNMPv2 context's MIB view. The value, included(1), indicates that the corresponding instances of viewSubtree and viewMask define a family of view subtrees included in the MIB view. The value, excluded(2), indicates that the corresponding instances of viewSubtree and viewMask define a family of view subtrees excluded from the MIB view.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER included(1), excluded(2)  

rSnmpViewStatus 1.3.6.1.4.1.64.9.19.8.1.4
Enter the status of this conceptual row in the viewTable.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

rlanSnmpTrapProfileTable 1.3.6.1.4.1.64.9.19.9
This table provides a management interface to the trap profile table objects.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanSnmpTrapProfileEntry

rlanSnmpTrapProfileEntry 1.3.6.1.4.1.64.9.19.9.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanSnmpTrapProfileEntry  

rSnmpTrapEnterprise 1.3.6.1.4.1.64.9.19.9.1.1
The object identifier of the enterprise in which this trap is defined. For example; to disable the gDChanUp trap defined in this MIB this object would contain the object identifier for gandalf (1.3.6.1.4.1.64).
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

rSnmpTrapId 1.3.6.1.4.1.64.9.19.9.1.2
The unique trap id that the associated enterprise has assigned this trap. For example; to disable the gDChanUp trap defined in this MIB this object would contain the value 9024.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rSnmpCommunities 1.3.6.1.4.1.64.9.19.9.1.3
The list of communities that are interested in this trap. Can also be used to disable traps. Communities are represented as a bit string where each bit in each octet represents a community. The most significant bit of octet one represents the community whose rSnmpTrapCommunityIndex value is one.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

rAuditingEnabled 1.3.6.1.4.1.64.9.20.1
Select this option when you want to enable auditing. Can only be enabled if a valid file transfer profile is set up for it.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rAuditTimeOfDayTransfer 1.3.6.1.4.1.64.9.20.2
Select this option when you want the system to transfer audit records at a specified time of day DEFAULT = disabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rAuditTimeOfDay 1.3.6.1.4.1.64.9.20.3
Enter the time of day you want the system to initiate the file transfer. NOTE: The times are entered as seconds but will only be accepted on a 60 sec boundary. A value of zero indicates midnight, a value of 60 indicates 12:01, 43200 indicates 12am, 86340 indicates 23:59 and so on. DEFAULT = 0
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86340  

rAuditRecordTermChars 1.3.6.1.4.1.64.9.20.4
Select the way you want the system to set up the termination records for individual audit records. DEFAULT = crlf
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER cr(1), lf(2), crlf(3)  

rAuditRecordsInFlash 1.3.6.1.4.1.64.9.20.5
Tells you how many audit records are are currently in flash memory. NOTE: After a file transfer, this field is reset to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

rlanFlashDirectoryTable 1.3.6.1.4.1.64.9.21.1
This table provides a management interface to the flash directory listings.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanFlashDirectoryEntry

rlanFlashDirectoryEntry 1.3.6.1.4.1.64.9.21.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanFlashDirectoryEntry  

rFlashFileIndex 1.3.6.1.4.1.64.9.21.1.1.1
Tells you the directory index associated with this file in flash memory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..16  

rFlashFileType 1.3.6.1.4.1.64.9.21.1.1.2
Tells you the type of file (e.g., BRI operating software) associated with this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rFlashFileId 1.3.6.1.4.1.64.9.21.1.1.3
Tells you id of this file in flash memory .
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rFlashFileAddress 1.3.6.1.4.1.64.9.21.1.1.4
Tells you the address of this file in flash memory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

rFlashFileSize 1.3.6.1.4.1.64.9.21.1.1.5
Tells you (in bytes) the size of this file in flash memory.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rFlashFileVersion 1.3.6.1.4.1.64.9.21.1.1.6
Tells you the software version of the file in flash memory.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rFlashFileCrc 1.3.6.1.4.1.64.9.21.1.1.7
Tells you whether the checksum for the embedded file(s) matches the checksum generated by the RSC.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER good(1), bad(2)  

rLANProtocolIDIdUnused 1.3.6.1.4.1.64.9.22.1
This object is used to identify a potentially unused index that can be used as the rLANProtocolIDId instance when creating new entries in the rlanLANProtocolIDTable. A returned value of zero indicates that the table is full.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..159  

rlanLANProtocolIDTable 1.3.6.1.4.1.64.9.22.2
This table provides an administrative view of the LAN protocol ID table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanLANProtocolIDEntry

rlanLANProtocolIDEntry 1.3.6.1.4.1.64.9.22.2.1
Each entry in this table is a LAN protocol ID and name. This entry can then be used in designing which protocol that is to be filtered or forwarded. Six default entries exist in this table which cannot be modified or deleted. They are: 122 Novell IPX/SPX 8137 123 AppleTalk ARP 80F3 124 AppleTalk 809B 125 Reverse ARP 8035 126 ARP 0806 127 TCP/IP 0800
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanLANProtocolIDEntry  

rLANProtocolIDId 1.3.6.1.4.1.64.9.22.2.1.1
Tells you the index of the entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..159  

rLANProtocolID 1.3.6.1.4.1.64.9.22.2.1.2
16 bit ID of the LAN protocol. You cannot modify the predefined entries.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1501..65535  

rLANProtocolIDName 1.3.6.1.4.1.64.9.22.2.1.3
Enter the identifier for this LAN protocol ID. You cannot modify the predefined entries.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rLANProtocolIDStatus 1.3.6.1.4.1.64.9.22.2.1.4
Enter the current status of this entry. NOTE: Entries that are currently in use (e.g., assigned to be filtered or forwarded) cannot be destroyed. The predefined entries cannot be destroyed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

rlanMdmCountry 1.3.6.1.4.1.64.9.23.1
This attribute configures the system for a specific country. DEFAULT = United States
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER argintina(1), australia(2), austria(3), belgium(4), brazil(5), canada(6), chile(7), china(8), columbia(9), czechRepublic(10), denmark(11), finland(12), france(13), germany(14), greece(15), hongKong(16), hungary(17), india(18), indonesia(19), ireland(20), israel(21), italy(22), italySip(23), japan(24), korea(25), malaysia(26), mexico(27), netherlands(28), newZealand(29), norway(30), peru(31), philippines(32), poland(33), saudiaArabia(34), singapore(35), southAfricA(36), spain(37), sweden(38), switzerland(39), tiawan(40), thailand(41), unitedKingdom(42), unitedStates(43)  

rlanMdmMode 1.3.6.1.4.1.64.9.23.3
Defines that modems are setup for either originate or answer. When there is an incomming call the setting in this object will be the default for all the modems. On an outgoing call the value of rRemLANMdmAnswer will control the individual modem. DEFAULT = modemAnswer
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER modemOriginate(1), modemAnswer(2)  

rlanMdmIDTable 1.3.6.1.4.1.64.9.23.4
The base table for the modems managed by this MIB. The rlanMdmLineTable, rlanMdmDTEInterfaceTable, rlanMdmCallControlTable, and rlanMdmStatsTable all augment the rows defined in this table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanMdmIDEntry

rlanMdmIDEntry 1.3.6.1.4.1.64.9.23.4.1
Entries in this table are created only by the agent. One entry exists for each modem managed by the agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanMdmIDEntry  

rMdmIDManufacturerOID 1.3.6.1.4.1.64.9.23.4.1.2
This value is intended to identify the manufacturer, model, and version of this modem. This may be used to identify the existance of enterprise-specific functions and behaviours.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OBJECT IDENTIFIER  

rlanMdmIDProductDetails 1.3.6.1.4.1.64.9.23.4.1.3
A textual description of this device, including the manufacturer's name, modem model name, hardware revision, firmware revision, and optionally, its serial number. The exact format of this description is defined by the vendor. This description may only contain characters from the NVT ASCII character set.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

rlanMdmLineTable 1.3.6.1.4.1.64.9.23.5
The modem Line Table augments the modem ID table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanMdmLineEntry

rlanMdmLineEntry 1.3.6.1.4.1.64.9.23.5.1
Entries in this table are created only by the agent. One entry exists for each modem managed by the agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanMdmLineEntry  

rMdmLineState 1.3.6.1.4.1.64.9.23.5.1.2
Allows the inspection of the state of the modem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER idle(1), incomingRing(2), dialingOrAnswering(3), waitingForCarrier(4), connected(5), busiedOut(6), disconnecting(7), retraining(8), rateChange(9)  

rlanMdmECTable 1.3.6.1.4.1.64.9.23.6
The modem error correcting table augments the modem ID table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanMdmECEntry

rlanMdmECEntry 1.3.6.1.4.1.64.9.23.6.1
Entries in this table are created only by the agent. One entry exists for each modem managed by the agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanMdmECEntry  

rMdmECErrorControlUsed 1.3.6.1.4.1.64.9.23.6.1.1
Indicates the error control method used during the current or previous call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), direct(2), mnp(3), lapmV42(4), sync(5)  

rlanMdmDCTable 1.3.6.1.4.1.64.9.23.7
The modem data compression table augments the modem ID table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanMdmDCEntry

rlanMdmDCEntry 1.3.6.1.4.1.64.9.23.7.1
Entries in this table are created only by the agent. One entry exists for each modem managed by the agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanMdmDCEntry  

rMdmDCCompressionTypeUsed 1.3.6.1.4.1.64.9.23.7.1.1
Indicates the data compression method used during the current or previous call. If no compression protocol is in use, this object shall have the value 1.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), v24bis(2), mnpClass5(3)  

rlanMdmSCTable 1.3.6.1.4.1.64.9.23.8
The modem signal convertor table augments the modem ID table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanMdmSCEntry

rlanMdmSCEntry 1.3.6.1.4.1.64.9.23.8.1
Entries in this table are created only by the agent. One entry exists for each modem managed by the agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanMdmSCEntry  

rMdmSCCurrentLineTransmitRate 1.3.6.1.4.1.64.9.23.8.1.1
The current link transmit rate of a connection, or the last link transmit rate of the last connection in bits per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

rMdmSCCurrentLineReceiveRate 1.3.6.1.4.1.64.9.23.8.1.2
The current link receive rate of a connection, or the last link receive rate of the last connection in bits per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

rMdmSCModulationSchemeUsed 1.3.6.1.4.1.64.9.23.8.1.5
The modulation scheme of the current or previous call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER bell103A(1), bell212A(2), v21(3), v22(4), v22bis(5), v23(6), v32(7), v32bis(8), vfc(9), v34(10), v34bis(11), x2(12), k56flex(13), v90(14)  

rlanMdmStatsTable 1.3.6.1.4.1.64.9.23.9
The modem statistics Table augments the modem ID table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanMdmStatsEntry

rlanMdmStatsEntry 1.3.6.1.4.1.64.9.23.9.1
Entries in this table are created only by the agent. One entry exists for each modem managed by the agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanMdmStatsEntry  

rMdmStatsRetrains 1.3.6.1.4.1.64.9.23.9.1.1
The number of retrains experienced on connections on this line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rMdmStatsSentOctets 1.3.6.1.4.1.64.9.23.9.1.2
The number of octets presented to the modem by the DTE.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rMdmStatsReceivedOctets 1.3.6.1.4.1.64.9.23.9.1.3
The number of octets presented to the DTE by the modem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rMdmStatsSentDataFrames 1.3.6.1.4.1.64.9.23.9.1.4
The number of data frames sent on the line interface. If there is no frame-oriented protocol in use on the line interface, this counter shall not increment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rMdmStatsReceivedDataFrames 1.3.6.1.4.1.64.9.23.9.1.5
The number of data frames received on the line interface. If there is no frame-oriented protocol in use on the line interface, this counter shall not increment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rMdmStatsResentFrames 1.3.6.1.4.1.64.9.23.9.1.6
The number of times this modem retransmits frames on the line interface. If there is no frame-oriented protocol in use on the line interface, this counter shall not increment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rMdmStatsErrorFrames 1.3.6.1.4.1.64.9.23.9.1.7
The number of block errors received on the link. If there is no frame-oriented protocol in use on the line interface, this counter shall not increment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

rMdmStatsDisconnectCause 1.3.6.1.4.1.64.9.23.9.1.8
The disconnect reason of the last call.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER lostCarrier(1), noCarrier(2), noDialtone(3), busy(4), reserved(5), reserved(6), watchdogTimeout(7), dtrDrop(9), userHangup(10), compressionProblem(12), retrainFailure(13), remoteLinkDisconnect(14), abort(15), terminateLostCarrier(16), reserved(17), inactivityTimeout(18), dialStringError(19), autoLogonError(20), ccpNotSeen(21), reserved(22), reserved(24), linkFailure(25), callbackFailed(26), modulationError(27), dialTimeout(28), remoteHangup(30), reserved(31), blacklist(32), lastMicrocomDiscReason(33), timeoutAtConnectTime(128), normalImpDisconnect(129), mdmResourceUnavailable(130), mdmResourceCommitted(131), mdmResourceError(132), lastMdmResultCodes(133)  

rMdmStatsControlList 1.3.6.1.4.1.64.9.23.9.1.9
Tells you the control signal state at the interface, which is bit- mapped as follows: Bit --- 0 RTS 1 DTR 2 CTS 3 DCD 4 DSR 5 TXDATA 6 RXDATA 7 OFFHOOK 8 SYNCINDICATION 9 MODEMRESET 10 RINGINDICATE NOTE: Bit zero (0) is the least significant bit.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rMdmStatsReceiveLevel 1.3.6.1.4.1.64.9.23.9.1.10
Received analog dBm level on the modem line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rMdmStatsTransmitLevel 1.3.6.1.4.1.64.9.23.9.1.11
Transmitted analog dBm level on the modem line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rMdmStatsSignalToNoiseRatio 1.3.6.1.4.1.64.9.23.9.1.12
The signal to noise ration of the modem.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rMdmStatsSpeedChanges 1.3.6.1.4.1.64.9.23.9.1.13
The number of speed changes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rlanMdmACCMTable 1.3.6.1.4.1.64.9.23.10
The ACC Mask table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanMdmACCMEntry

rlanMdmACCMEntry 1.3.6.1.4.1.64.9.23.10.1
Entries in this table are created only by the agent. One entry exists for each modem managed by the agent.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanMdmACCMEntry  

rMdmACCMRx 1.3.6.1.4.1.64.9.23.10.1.1
ACCM Received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..12)  

rMdmACCMTx 1.3.6.1.4.1.64.9.23.10.1.2
ACCM Transmitted.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..12)  

rPppNegotiateFirst 1.3.6.1.4.1.64.9.24.1
This attribute defines which PPP authentication protocol is negotiated first on incoming call. DEFAULT = chap
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER chap(1), pap(2)  

rPppDynamicIPAddr 1.3.6.1.4.1.64.9.24.2
This attribute defines the start address of the dynamic addres pool.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

rPppNumDynamicIPAddr 1.3.6.1.4.1.64.9.24.3
This attribute defines the number of dynamic IP addresses in the pool.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..150  

rPppDynamicIPAdrrHoldoff 1.3.6.1.4.1.64.9.24.4
This attribute defines the time in seconds befor the same IP address can be reused after a call has been disconnected.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..300  

rPppDNSServerIPAddr 1.3.6.1.4.1.64.9.24.5
This attribute defines the DNS server IP address of your Network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

rPppRemDNSIPAddrHandling 1.3.6.1.4.1.64.9.24.6
This attribute determines wether the system can accept or override the DNS IP address submitted by a remote system. DEFAULT = accept. Override has been superceded by overridewith.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER accept(1), override(2), overridewith(3)  

rPppSecondaryDNSServerIPAddr 1.3.6.1.4.1.64.9.24.7
This attribute defines the Secondary DNS server IP address of your Network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

rPppPrimaryWINSServerIPAddr 1.3.6.1.4.1.64.9.24.8
This attribute defines the Primary WINS server IP address of your Network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

rPppSecondaryWINSServerIPAddr 1.3.6.1.4.1.64.9.24.9
This attribute defines the Secondary WINS server IP address of your Network.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

rRemExtIDUnused 1.3.6.1.4.1.64.9.25.1
This object is used to identify a potentially unused index to be used as the rRemExtID when creating new entries in the rlanRemExtConfigTable. A returned value of zero indicates that the table is full.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..512  

rlanRemExtConfigTable 1.3.6.1.4.1.64.9.25.2
This table provides a management view of the system configuration specific to individual Remote Extensions.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanRemExtConfigEntry

rlanRemExtConfigEntry 1.3.6.1.4.1.64.9.25.2.1
The conceptual row at instance zero is used by the Xpressway/XpressStack as the default remote Extension configuration. This entry is also used to change the defaults chosen when manually configuring a new remote Extension either through the embedded console or via SNMP.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanRemExtConfigEntry  

rRemExtID 1.3.6.1.4.1.64.9.25.2.1.1
Tells you the index of this remote Extension. A value of 0 indicates the default remote-Extension configuration; that is, this entry is used to determine the default parameters for remote Extensions
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..512  

rRemExtName 1.3.6.1.4.1.64.9.25.2.1.2
Enter the name of the current remote Extension. The name can use up to 16 characters but cannot contain spaces. The combination of name and pbx extension number must be unique. The default entry (instance zero) cannot be modified.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rRemExtPbxExtension 1.3.6.1.4.1.64.9.25.2.1.3
The numeric extension of this remote extension, 1 to 8 digits. Must be defined. The combination of name and pbx extension number must be unique. The default entry (instance zero) cannot be modified.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..8)  

rRemExtAdminState 1.3.6.1.4.1.64.9.25.2.1.4
The current administrative state of the remote Extension.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rRemExtPasswdAdminState 1.3.6.1.4.1.64.9.25.2.1.5
The current Administrative state of the remote Extension's password.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rRemExtPasswd 1.3.6.1.4.1.64.9.25.2.1.6
The remote Extension password. Must be a numeric string and must be defined if password admin state is enabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

rRemExtIdleDisconnectTimer 1.3.6.1.4.1.64.9.25.2.1.7
The time in seconds in which the call will be disconnected when idle. Valid values are 5 to 300.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 5..300  

rRemExtTimeOfDayProfileId 1.3.6.1.4.1.64.9.25.2.1.8
The id of the remote extensions Time Of Day profile
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..64  

rRemExtConnectedToCard 1.3.6.1.4.1.64.9.25.2.1.9
The VIM card that this extension is connected to. In the case of a 5232, use 1 for this field.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..4  

rRemExtConnectedToModule 1.3.6.1.4.1.64.9.25.2.1.10
The module that this extension is connected to. In the case of a 5232, use 1 for this field.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..5  

rRemExtConnectedToChannel 1.3.6.1.4.1.64.9.25.2.1.11
The channel of the module that this extension is connected to. In the case of a 5232, use 1 for this field.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..6  

rRemExtPhoneEndPhNumber 1.3.6.1.4.1.64.9.25.2.1.12
The phone number at the phone end of this PBX extender call. The first character of this field can be L(ocal), N(ational), or I(nternational).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

rRemExtSwitchEndPhNumber 1.3.6.1.4.1.64.9.25.2.1.13
The phone number at the switch end of this PBX extender call. The first character of this field can be L(ocal), N(ational), or I(nternational).
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

rRemExtDialPrefix 1.3.6.1.4.1.64.9.25.2.1.14
The index (1-33) of the dial prefix of this remote extension. 1 means no dial prefix.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..33  

rRemExtChannelGroup 1.3.6.1.4.1.64.9.25.2.1.15
The index (1-65) of the channel group of this remote extension. 1 is the default group.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..65  

rRemExtCLID 1.3.6.1.4.1.64.9.25.2.1.16
The calling line ID of the remote unit. When CLID security is enabled, the CLID must match the number here for the call to be accepted.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rRemExtMakeSetBusyAdminState 1.3.6.1.4.1.64.9.25.2.1.17
The administrative state of the MakeSetBusy function.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rRemExtMakeSetBusyKey 1.3.6.1.4.1.64.9.25.2.1.18
The key value that activates the MakeSetBusy function
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1)  

rRemExtLogoutSequence 1.3.6.1.4.1.64.9.25.2.1.19
The numeric logout sequence.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

rRemExtCallProcessing 1.3.6.1.4.1.64.9.25.2.1.20
The call processing type associated with this remote extension.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER lamp(2), ring(3), voice(4)  

rRemExtStatus 1.3.6.1.4.1.64.9.25.2.1.21
The current status of this remote extension entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

rRemExtCallForce 1.3.6.1.4.1.64.9.25.2.1.22
To tell the system to disconnect this remote Extension, select disconnect from the list of available options. When you select connect, the system will try to connect to the remote Extension on an available channel as specified in the rlanDestAddressConfigTable selection parameters (i.e., channel group) DEFAULT = statusQuo.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER connect(1), disconnect(2), statusQuo(3)  

rRemExtLineKey 1.3.6.1.4.1.64.9.25.2.1.23
The mask representing the line keys to use.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(8)  

rRemExtRxGain 1.3.6.1.4.1.64.9.25.2.1.24
The attenuation or gain of the recieved PBX signal. This value is stored in the database as -7 to 9. It is represented in this MIB as 1 to 17.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..17  

rRemExtTxGain 1.3.6.1.4.1.64.9.25.2.1.25
The attenuation or gain of the transmitted PBX signal. This value is stored in the database as -9 to 7. It is represented in this MIB as 1 to 17.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..17  

rRemExtPbxInterface 1.3.6.1.4.1.64.9.25.2.1.26
Select the type of PBX connection used for this remote extension DEFAULT = vrm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER vrm(1), dpnss(2)  

rRemExtOutgoingBearer 1.3.6.1.4.1.64.9.25.2.1.27
Select the type of bearer to use for outgoing calls to this remote extension. DEFAULT = kbps64Unrestrict.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER kbps64Unrestrict(1), kbps56Dig(2)  

rRemExtDivertImmediate 1.3.6.1.4.1.64.9.25.2.1.28
The phone number to divert all calls intended for this extension to. For normal operation, leave this entry blank. This entry can be modified from the remote extension using a 'star' sequence.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rRemExtDivertBusy 1.3.6.1.4.1.64.9.25.2.1.29
The phone number to divert all calls intended for this extension to, whilst the extension is busy. Leave this entry blank to disable this facility. This entry can be modified from the remote extension using a 'star' sequence.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rRemExtDivertNoAnswer 1.3.6.1.4.1.64.9.25.2.1.30
The phone number to divert all calls intended for this extension to, if there is no answer from this extension. Leave this entry blank to disable this facility. This entry can be modified from the remote extension using a 'star' sequence.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rRemExtOfficeExtension 1.3.6.1.4.1.64.9.25.2.1.31
If the home-worker also has an office extension number, it should be entered here. Certain facilities are aonly available to this extension for security purposes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rlanRemExtStatsTable 1.3.6.1.4.1.64.9.25.3
This table provides a management view of the system configuration specific to individual Remote Extensions.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanRemExtStatsEntry

rlanRemExtStatsEntry 1.3.6.1.4.1.64.9.25.3.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanRemExtStatsEntry  

rRemExtVoiceModule 1.3.6.1.4.1.64.9.25.3.1.1
Tells you the channel index of the Voice module in use.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rRemExtIsdnChan 1.3.6.1.4.1.64.9.25.3.1.2
Tells you the channel index of the ISDN channel used.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rRemExtTotalTime 1.3.6.1.4.1.64.9.25.3.1.3
Tells you the total number of TimeTicks that have elapsed while this remote extension has been connected. This value resets when the RLAN resets. Returns a 0 if a connection has yet to be made.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

rRemExtLastTime 1.3.6.1.4.1.64.9.25.3.1.4
Tells you the time in TimeTicks of the last connection to this remote extension. Returns a 0 if a connection has yet to be made.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

rRemExtCallDuration 1.3.6.1.4.1.64.9.25.3.1.5
Tells you the number of TimeTicks that have elapsed since this connection has been established. This value resets every time the remote extention reconnects. Returns a 0 if a connection has yet to be made.
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

rRemExtLastFail 1.3.6.1.4.1.64.9.25.3.1.6
Tells you the last calls failure code.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rRemExtWANStatsIndex 1.3.6.1.4.1.64.9.25.3.1.7
This indicates active entry in the rlanWANStatsTable entries. 0 indicates that this remote LAN is currently not active (up).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

rTimeOfDayIDUnused 1.3.6.1.4.1.64.9.26.1
This object is used to identify a potentially unused index to be used as the rRemTimeOfDayID when creating new entries in the rlanRemTimeOfDayTable. A returned value of zero indicates that the table is full.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..64  

rlanTimeOfDayProfileTable 1.3.6.1.4.1.64.9.26.2
This table provides a management view of the system configuration specific to individual Time Of day entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanTimeOfDayEntry

rlanTimeOfDayProfileEntry 1.3.6.1.4.1.64.9.26.2.1
Partial entry
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanTimeOfDayProfileEntry  

rTimeOfDayProfileID 1.3.6.1.4.1.64.9.26.2.1.1
Tells you the index of this Time Of Day entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..64  

rTimeOfDayProfileName 1.3.6.1.4.1.64.9.26.2.1.2
Tells you the name of this Time Of Day entry. No whitespace and must be unique. Must be defined.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

rTimeOfDayProfileStatus 1.3.6.1.4.1.64.9.26.2.1.3
The current status of this remote extension entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

rlanTimeOfDayEntryTable 1.3.6.1.4.1.64.9.26.3
This table provides a management view of the system configuration specific to individual Time Of day profile entries.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanTimeOfDayEntry

rlanTimeOfDayEntry 1.3.6.1.4.1.64.9.26.3.1
Partial entry
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanTimeOfDayEntry  

rTimeOfDayEntryID 1.3.6.1.4.1.64.9.26.3.1.1
Tells you the index of this Time Of Day profile entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..10  

rTimeOfDayEntryStart 1.3.6.1.4.1.64.9.26.3.1.2
The start time of this TOD profile entry. The format is an unsigned long taken from the number of minutes from Sunday Midnight. For example, if the start time is Monday at 06:00 this value would be 360. This value must be less than rTimeOfDayProfileEnd and larger than the end time of the previous entry
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..10079  

rTimeOfDayEntryEnd 1.3.6.1.4.1.64.9.26.3.1.3
The end time of this TOD profile entry. The format is an unsigned long taken from the number of minutes from Sunday Midnight. For example, if the start time is Monday at 06:01 this value would be 361. This value must be greater than rTimeOfDayProfileStart and smaller than the start time of the next entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..10079  

rTimeOfDayEntryIdleDisconnect 1.3.6.1.4.1.64.9.26.3.1.4
Is idle disconnect enabled or disabled during this time span.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rTimeOfDayEntryExclusive 1.3.6.1.4.1.64.9.26.3.1.5
Is exclusive enabled or disabled during this time span. That is, are other phones allowed to connect.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rlanDpnssBchConfigTable 1.3.6.1.4.1.64.9.27.1
This table provides a management view of the B-Channel configuration items specific to DPNSS links.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanDpnssBchConfigEntry

rlanDpnssBchConfigEntry 1.3.6.1.4.1.64.9.27.1.1
Entry defining DPNSS specific B-channel attributes.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanDpnssBchConfigEntry  

rDpnssBchCardID 1.3.6.1.4.1.64.9.27.1.1.1
The PRI card this entry is referring to
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..11  

rDpnssBchPortID 1.3.6.1.4.1.64.9.27.1.1.2
The PRI port this entry is referring to
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..2  

rDpnssBchChanID 1.3.6.1.4.1.64.9.27.1.1.3
The PRI B-channel this entry is referring to
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..31  

rDpnssBchRealXy 1.3.6.1.4.1.64.9.27.1.1.4
Select the collision handling of this B-channel. Each B-channel should be set as X on one end of the link and Y on the other end. If there is a call collision on this channel, the end designated X will succeed, whilst the end designated Y will drop back and retry on a different channel. DEFAULT = x.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER x(1), y(2)  

rDpnssBchVirtualMode 1.3.6.1.4.1.64.9.27.1.1.5
For each B-channel on a DPNSS link there is a corresponding virtual channel, which is used to signal call-independant information through the network. Usually all of these channels will be enabled, but a subset may be disabled. DEFAULT = enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rDpnssBchVirtualXy 1.3.6.1.4.1.64.9.27.1.1.6
Select the collision handling of this Virtual B-channel. DEFAULT = x.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER x(1), y(2)  

rlanIsdnDDIRoutingTable 1.3.6.1.4.1.64.9.28.1
This table provides a management view of the ISDN Call Routing Table, used to provide incoming call handling ability based on information in the ISDN Setup message.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanIsdnDDIRoutingEntry

rlanIsdnDDIRoutingEntry 1.3.6.1.4.1.64.9.28.1.1
Entry defining incoming call handling for ISDN initiated calls.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanIsdnDDIRoutingEntry  

rIsdnDDIRtgIndex 1.3.6.1.4.1.64.9.28.1.1.1
Uniquely identifies this entry
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

rIsdnDDIRtgName 1.3.6.1.4.1.64.9.28.1.1.2
Tells you the name of this Routing Table entry. No whitespace and must be unique. Must be defined.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rIsdnDDIRtgRacLoPhnum 1.3.6.1.4.1.64.9.28.1.1.3
A range of phone numbers can be defined such that all incoming calls with a dialled number in this range are presented to the RAC as data calls. The default for dialled numbers outside of this range is to route the call to the PBX. This is the lower bound of the range.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

rIsdnDDIRtgRacHiPhnum 1.3.6.1.4.1.64.9.28.1.1.4
A range of phone numbers can be defined such that all incoming calls with a dialled number in this range are presented to the RAC as data calls. The default for dialled numbers outside of this range is to route the call to the PBX. This is the higher bound of the range.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

rIsdnDDIRtgApexPhnum 1.3.6.1.4.1.64.9.28.1.1.5
Enter the dialled number which is reserved for remote analogue extensions to call.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

rIsdnDDIRtgAbsorb 1.3.6.1.4.1.64.9.28.1.1.6
For calls which are passed on to the PBX, a simple number mapping algorithm can be performed on the dialled number to accomodate the PBXs numbering plan. Enter the number of digits to absorb from the front of the dialled number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..16  

rIsdnDDIRtgInsert 1.3.6.1.4.1.64.9.28.1.1.7
For calls which are passed on to the PBX, a simple number mapping algorithm can be performed on the dialled number to accomodate the PBXs numbering plan. Enter a digit string to insert at the front of the dialled number.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..16)  

rIsdnDDIRtgRowStatus 1.3.6.1.4.1.64.9.28.1.1.8
The current status of this routing table entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

rlanPbxCallRoutingTable 1.3.6.1.4.1.64.9.28.2
This table provides a management view of the PBX Call Routing Table, used to provide incoming call handling ability based on information Initial Service Request Message (ISRM) from the PBX.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanPbxCallRoutingEntry

rlanPbxCallRoutingEntry 1.3.6.1.4.1.64.9.28.2.1
Entry defining incoming call handling for PBX initiated calls.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanPbxCallRoutingEntry  

rPbxCallRtgIndex 1.3.6.1.4.1.64.9.28.2.1.1
Uniquely identifies this entry
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

rPbxCallRtgName 1.3.6.1.4.1.64.9.28.2.1.2
Tells you the name of this Routing Table entry. No whitespace and must be unique. Must be defined.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..16)  

rPbxCallRtgGwayPhnum 1.3.6.1.4.1.64.9.28.2.1.3
Calls from a PBX where the called number begins with this prefix are routed directly into the ISDN, i.e. using the RLAN as an ISDN gateway. Leave blank if calls from the PBX to the ISDN are not required. An asterisk may be used to indicate this is the default route.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..1)  

rPbxCallRtgGwayAbsorb 1.3.6.1.4.1.64.9.28.2.1.4
When calls are routed through to the ISDN because they meet the criteria above, this field indicates how many digits to discard from the front of the called number. Generally the prefix used for routing is absorbed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..1  

rPbxCallRtgRacExtLo 1.3.6.1.4.1.64.9.28.2.1.5
When the RLAN has a PBX connection, a range of extension numbers are allocated to the RLAN. Calls received by the RLAN down the PBX trunk are treated as normal data calls. This is the low-entry of the range.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

rPbxCallRtgRacExtHi 1.3.6.1.4.1.64.9.28.2.1.6
When the RLAN has a PBX connection, a range of extension numbers are allocated to the RLAN. Calls received by the RLAN down the PBX trunk are treated as normal data calls. This is the high-entry of the range.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

rPbxCallRtgApexExtLo 1.3.6.1.4.1.64.9.28.2.1.7
When the RLAN has a PBX connection, a range of extension numbers are allocated to Remote Extensions. This is the low-entry of the range.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

rPbxCallRtgApexExtHi 1.3.6.1.4.1.64.9.28.2.1.8
When the RLAN has a PBX connection, a range of extension numbers are allocated to Remote Extensions. This is the high-entry of the range.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..8)  

rPbxCallRtgRowStatus 1.3.6.1.4.1.64.9.28.2.1.9
The current status of this routing table entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

rlanSecurityBannerConfigTable 1.3.6.1.4.1.64.9.29.1
This table provides a management view of the login banner configuration parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanSecurityBannerConfigEntry

rlanSecurityBannerConfigEntry 1.3.6.1.4.1.64.9.29.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanSecurityBannerConfigEntry  

rSecBannerBanner 1.3.6.1.4.1.64.9.29.1.1.1
The authentication Banner String. This is the banner that users see before they login. Printable characters must be enclosed in quotation marks, non printable characters entered in 3 digit decimal numbers, separated by commas. Length of banner to be sent must not exceed 512 bytes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..700)  

rSecBannerLogin 1.3.6.1.4.1.64.9.29.1.1.2
The authentication Login prompt. Printable characters must be enclosed in quotation marks, non printable characters entered in 3 digit decimal numbers, separated by commas. Length of banner to be sent must not exceed 32 bytes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..100)  

rSecBannerPassword 1.3.6.1.4.1.64.9.29.1.1.3
The authentication Password prompt. Printable characters must be enclosed in quotation marks, non printable characters entered in 3 digit decimal numbers, separated by commas. Length of banner to be sent must not exceed 32 bytes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..100)  

rSecBannerAccepted 1.3.6.1.4.1.64.9.29.1.1.4
The authentication Accepted banner. This is the banner the user sees when login is successful. Printable characters must be enclosed in quotation marks, non printable characters entered in 3 digit decimal numbers, separated by commas. Length of banner to be sent must not exceed 32 bytes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..100)  

rSecBannerDenied 1.3.6.1.4.1.64.9.29.1.1.5
The authentication Denied banner. This is the banner the user sees when login is unsuccessful. Printable characters must be enclosed in quotation marks, non printable characters entered in 3 digit decimal numbers, separated by commas. Length of banner to be sent must not exceed 32 bytes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..100)  

rSecBannerPart1 1.3.6.1.4.1.64.9.29.1.1.6
The first part of the authentication Banner String. This is the banner that users see before they login. The banner is split into 3 parts to accomodate SNMP implementations that cannot read strings larger than 256 characters. Printable characters must be enclosed in quotation marks, non printable characters entered in 3 digit decimal numbers, separated by commas. Length of banner to be sent must not exceed 512 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

rSecBannerPart2 1.3.6.1.4.1.64.9.29.1.1.7
The second part of the authentication Banner String. This is the banner that users see before they login. The banner is split into 3 parts to accomodate SNMP implementations that cannot read strings larger than 256 characters. Printable characters must be enclosed in quotation marks, non printable characters entered in 3 digit decimal numbers, separated by commas. Length of banner to be sent must not exceed 512 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

rSecBannerPart3 1.3.6.1.4.1.64.9.29.1.1.8
The third part of the authentication Banner String. This is the banner that users see before they login. The banner is split into 3 parts to accomodate SNMP implementations that cannot read strings larger than 256 characters. Printable characters must be enclosed in quotation marks, non printable characters entered in 3 digit decimal numbers, separated by commas. Length of banner to be sent must not exceed 512 bytes.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

rlanIpRoutingConfigTable 1.3.6.1.4.1.64.9.30.1
This table provides a management view of the login banner configuration parameters.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    RlanIpRoutingConfigEntry

rlanIpRoutingConfigEntry 1.3.6.1.4.1.64.9.30.1.1
Tok_String
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  RlanIpRoutingConfigEntry  

rIpRoutingArpProxy 1.3.6.1.4.1.64.9.30.1.1.1
Enables ARP Proxy
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rIpRoutingRipForwarding 1.3.6.1.4.1.64.9.30.1.1.2
Enables RIP Forwarding
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

rIpRoutingRipType 1.3.6.1.4.1.64.9.30.1.1.3
The type of RIP Forwarding
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER rip1(1), rip2(2)  

gCardInstalled 9000
This trap indicates that a card was physically installed in the hub. The trap will include the rCardID attribute that identifies which card was installed.
TRAP-TYPE    

gCardRemoved 9001
This trap indicates that a card was physically removed from the hub. The trap will include the rCardID attribute that identifies which card was removed.
TRAP-TYPE    

gCardMismatch 9002
This trap indicates that a card was physically installed in a slot configured with a different card type. The rCardID attribute identifying the installed card and the rCardType attribute for this card are going to be included with this trap.
TRAP-TYPE    

gCardMismatchCleared 9003
This trap indicates that the slot causing a Card Mismatch was reconfigured with the proper card type. The rCardID attribute and rCardType attribute will be included with this trap.
TRAP-TYPE    

gCardFaulty 9004
This trap indicates that a card was found to be faulty by the system. The rCardID attribute will be included with the trap. The text portion of the trap will identify the reason the card was found to be faulty.
TRAP-TYPE    

gCardFaultyCleared 9005
This trap indicates that the slot causing a Card Faulty is now functional again. The rCardID identifying the slot will be included with the trap.
TRAP-TYPE    

gNvramFault 9006
This trap indicates that one of the data objects stored in NVRAM failed a CRC test. This object will then be reconfigured with its default parameters.
TRAP-TYPE    

gFiltDatabaseFull 9007
This trap indicates that the number of entries in the Filtering Database has reached the upper limit of the system's storage capacity.
TRAP-TYPE    

gRTCFault 9008
This trap indicates that the internal tests done by the operational code on the Real Time Clock failed.
TRAP-TYPE    

gLANTestFailure 9009
This trap indicates that the internal tests done by the operational code on the LAN interface failed.
TRAP-TYPE    

gCallConnected 9010
The system just connected to remote LAN. Included with this TRAP will be the rWANStatsIndex, rWANStatsCardID, rWANStatsPortID, rWANStatsChanID and rWANStatsRemLANID identifying which card, port, channel, resource module connected and remote LAN this call will use.
TRAP-TYPE    

gCallDisconnected 9011
The system just disconnected from a remote LAN. Included with this trap will be the rWANStatsIndex, rWANStatsCardID, rWANStatsPortID, rWANStatsChanID identifying which card, port and channel, resource module connected were associated with this WAN link.
TRAP-TYPE    

gCallFailure 9012
The system refused a connection. If the system rSysTrapCall is set, the TRAP will be sent to the TRAP communities.
TRAP-TYPE    

gP1Backplane 9013
The system could not detect the presence of a P1 backplane.
TRAP-TYPE    

gDatabaseInvalid 9014
On startup, the system found that the database was a newer revision than the database.
TRAP-TYPE    

gNetsyncGain 9015
The system detected the presence of the NETSYNC clock.
TRAP-TYPE    

gNetsyncLoss 9016
The system detected the loss of the NETSYNC clock.
TRAP-TYPE    

gCompression 9017
The system detected that the compression engine couldn't startup. The text description gives the reason.
TRAP-TYPE    

gSecurity 9018
The system detected a security violation when attempting to accept a call.
TRAP-TYPE    

gInvalidISDNSwitch 9019
The system detected that the I/O card had a software image that wouldn't run with the ISDN switch currently set for the card.
TRAP-TYPE    

gXferSuccessful 9020
The system detected that the file transfer was successful.
TRAP-TYPE    

gXferFailed 9021
The system detected that the file transfer was not successful.
TRAP-TYPE    

gCardOverLimit 9022
The system detected that the maximum number of channels allowed per system has been exceeded.
TRAP-TYPE    

gLeasedLineFault 9023
The system detected that the connection on a leased line has failed. A trap will be generated every fifteen minutes until the connection is completed.
TRAP-TYPE    

gDChanUp 9024
The system detected that a D channel has been successfully brought up.
TRAP-TYPE    

gDChanDown 9025
The system detected a that D channel has been dropped.
TRAP-TYPE    

gInvalidPortConf 9026
The system detected that a port configuration attribute has been configured incorrectly.
TRAP-TYPE    

gCfgChangeNotApplied 9027
The system detected thath a configuration change has not yet been applied. The specific card must be restarted for the change to take affect.
TRAP-TYPE    

gSoftwareLoadIs 9028
The system detected a variant version of software has been downloaded to an I/O card.
TRAP-TYPE    

gDuplicateNetwork 9029
The system detected a duplicate IPX network number.
TRAP-TYPE    

gSapTableFull 9030
The system detected that the SAP table has reached its 500th Static entry or 2100th Dynamic entry.
TRAP-TYPE    

gAuditRecordsLost 9031
This trap is generated whenever audit records have been lost.
TRAP-TYPE    

gLongCall 9032
This trap is generated whenever a call to a remote LAN has been connected for longer than the Long Call period.
TRAP-TYPE    

gDChanFaulty 9033
This trap is generated whenever a D channel is unstable and losses the DSL more than the set threshold allows.
TRAP-TYPE    

gAddressMovedTooOften 9034
This trap is generated whenever a mac address moves from lan to lan too often which can cause an unstable network.
TRAP-TYPE    

gTestPresenceCallPassed 9035
This trap is generated when a test presence call is successful, that is the remote either rang or answered the call.
TRAP-TYPE    

gTestPresenceCallFailed 9036
This trap is generated when a test presence call failed.
TRAP-TYPE    

gTestPresenceCallNotIssued 9037
This trap is generated when the system is unable to issue a test presence call. This is not an indication that the intended remote LAN is not functional, thus the call should be re- attempted.
TRAP-TYPE    

gCardStateChanged 9038
This trap indicates that the state of a card has changed. The rCardID identifying the slot will be included with the trap and the rCardOpState indicating the new card state.
TRAP-TYPE    

gHardwareMismatch 9039
This trap indicates that the hardware that is present is not the hardware that is expected.
TRAP-TYPE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor