Wellfleet-SWSMDS-MIB

File: Wellfleet-SWSMDS-MIB.mib (73358 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC-1215
RFC1213-MIB Wellfleet-COMMON-MIB

Imported symbols

IpAddress Counter Gauge
TimeTicks Opaque enterprises
mgmt OBJECT-TYPE TRAP-TYPE
DisplayString mib-2 wfSmdsSwGroup

Defined Types

WfSmdsSwSubEntry  
SEQUENCE    
  wfSmdsSwSubDelete INTEGER
  wfSmdsSwSubDisable INTEGER
  wfSmdsSwSubState INTEGER
  wfSmdsSwSubCct INTEGER
  wfSmdsSwSubDisableHrtbtPoll INTEGER
  wfSmdsSwSubHrtbtPollAddr INTEGER
  wfSmdsSwSubHrtbtPollInterval INTEGER
  wfSmdsSwSubHrtbtPollDownCount INTEGER
  wfSmdsSwSubDisableNetMgmt INTEGER
  wfSmdsSwSubInterfaceType INTEGER
  wfSmdsSwSubInterfaceIndex INTEGER
  wfSmdsSwSubDisableL3PduChecks INTEGER
  wfSmdsSwSubDisableUsageGeneration INTEGER
  wfSmdsSwSubDisableMIR INTEGER
  wfSmdsSwSubUnassignedSAs Counter
  wfSmdsSwSubSAScreenViolations Counter
  wfSmdsSwSubDAScreenViolations Counter
  wfSmdsSwSubNumPDUExceededMIR Counter
  wfSmdsSwSubSipL3ReceivedIAs Counter
  wfSmdsSwSubSipL3ReceivedGAs Counter
  wfSmdsSwSubSipL3UnrecIAs Counter
  wfSmdsSwSubSipL3UnrecGAs Counter
  wfSmdsSwSubSipL3SentIAs Counter
  wfSmdsSwSubSipL3SentGAs Counter
  wfSmdsSwSubSipL3Errors Counter
  wfSmdsSwSubSipL3InvAddrTypes Counter
  wfSmdsSwSubSipL3VersionSupport INTEGER
  wfSmdsSwSubSAScrnViolationOccur OCTET STRING
  wfSmdsSwSubDAScrnViolationOccur OCTET STRING
  wfSmdsSwSubUnassignedSAOccur OCTET STRING
  wfSmdsSwSubSAErrorOccur OCTET STRING
  wfSmdsSwSubDAErrorOccur OCTET STRING
  wfSmdsSwSubInvalidBASizeOccur OCTET STRING
  wfSmdsSwSubInvalidHELenOccur OCTET STRING
  wfSmdsSwSubInvalidHEVerOccur OCTET STRING
  wfSmdsSwSubInvalidHECarOccur OCTET STRING
  wfSmdsSwSubInvalidHEPadOccur OCTET STRING
  wfSmdsSwSubBEtagOccur OCTET STRING
  wfSmdsSwSubBAsizeNELenOccur OCTET STRING
  wfSmdsSwSubIncorrectLenOccur OCTET STRING
  wfSmdsSwSubExceededMIROccur OCTET STRING
  wfSmdsSwSubInBandMgmtDisable INTEGER
  wfSmdsSwSubInBandMgmtLocalAddr OCTET STRING
  wfSmdsSwSubInBandMgmtReceivedPDUs Counter
  wfSmdsSwSubInBandMgmtSentPDUs Counter
  wfSmdsSwSubInBandMgmtMaxLenErrors Counter
  wfSmdsSwSubInBandMgmtEncapsErrors Counter
  wfSmdsSwSubGAPartialResolve Counter
  wfSmdsSwSubDANotOnSni Counter

WfSmdsSwEndpEntry  
SEQUENCE    
  wfSmdsSwEndpDelete INTEGER
  wfSmdsSwEndpE164AddrHigh OCTET STRING
  wfSmdsSwEndpE164AddrDelta OCTET STRING
  wfSmdsSwEndpInterfaceIndex INTEGER

WfSmdsSwInterfaceEntry  
SEQUENCE    
  wfSmdsSwInterfaceDelete INTEGER
  wfSmdsSwInterfaceType INTEGER
  wfSmdsSwInterfaceIndex INTEGER
  wfSmdsSwInterfaceIpAddr IpAddress
  wfSmdsSwInterfaceMIR INTEGER
  wfSmdsSwInterfaceCurrentRate INTEGER

WfSmdsSwAssocScrnEntry  
SEQUENCE    
  wfSmdsSwAssocScrnDelete INTEGER
  wfSmdsSwAssocScrnSniIndex INTEGER
  wfSmdsSwAssocScrnAddrInd OCTET STRING
  wfSmdsSwAssocScrnIndivIndex INTEGER
  wfSmdsSwAssocScrnGrpIndex INTEGER

WfSmdsSwIAScrnEntry  
SEQUENCE    
  wfSmdsSwIAScrnDelete INTEGER
  wfSmdsSwIAScrnSniIndex INTEGER
  wfSmdsSwIAScrnIndex INTEGER
  wfSmdsSwIAScrnAddr OCTET STRING

WfSmdsSwGAScrnEntry  
SEQUENCE    
  wfSmdsSwGAScrnDelete INTEGER
  wfSmdsSwGAScrnSniIndex INTEGER
  wfSmdsSwGAScrnIndex INTEGER
  wfSmdsSwGAScrnAddr OCTET STRING

WfSmdsSwGAEntry  
SEQUENCE    
  wfSmdsSwGADelete INTEGER
  wfSmdsSwGASSI INTEGER
  wfSmdsSwGAGroupAddress OCTET STRING
  wfSmdsSwGAGroupMember OCTET STRING

WfSmdsSwCurUsageEntry  
SEQUENCE    
  wfSmdsSwCurUsageDelete INTEGER
  wfSmdsSwCurUsageSni INTEGER
  wfSmdsSwCurUsageDestAddr OCTET STRING
  wfSmdsSwCurUsageSrcAddr OCTET STRING
  wfSmdsSwCurUsageGrpIndAddr OCTET STRING
  wfSmdsSwCurUsageNumL3Pdu Counter
  wfSmdsSwCurUsageNumOctet Counter
  wfSmdsSwCurUsageToBeDeleted INTEGER

WfSmdsSwUsageEntry  
SEQUENCE    
  wfSmdsSwUsageDelete INTEGER
  wfSmdsSwUsageSni INTEGER
  wfSmdsSwUsageDestAddr OCTET STRING
  wfSmdsSwUsageSrcAddr OCTET STRING
  wfSmdsSwUsageStartTimeStampHigh INTEGER
  wfSmdsSwUsageStartTimeStampLow INTEGER
  wfSmdsSwUsageEndTimeStampHigh INTEGER
  wfSmdsSwUsageEndTimeStampLow INTEGER
  wfSmdsSwUsageSentL3PduHigh INTEGER
  wfSmdsSwUsageSentL3PduLow INTEGER
  wfSmdsSwUsageSentOctetHigh INTEGER
  wfSmdsSwUsageSentOctetLow INTEGER
  wfSmdsSwUsageLastL3PduHigh INTEGER
  wfSmdsSwUsageLastL3PduLow INTEGER
  wfSmdsSwUsageLastOctetHigh INTEGER
  wfSmdsSwUsageLastOctetLow INTEGER
  wfSmdsSwUsageGrpIndAddr OCTET STRING

WfSmdsSwSsiSniEntry  
SEQUENCE    
  wfSmdsSwSsiSniDelete INTEGER
  wfSmdsSwSsiSniSSI INTEGER
  wfSmdsSwSsiSniSNI INTEGER

Defined Values

wfSmdsSwSubTable 1.3.6.1.4.1.18.3.5.9.7.1
The Wellfleet SMDS Switch Circuit (SNI, subscriber) Record. This record holds information on a per circuit (SSI, SNI, subscriber) basis.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfSmdsSwSubEntry

wfSmdsSwSubEntry 1.3.6.1.4.1.18.3.5.9.7.1.1
Per Wellfleet circuit SMDS Switch configuration parameters and counters. This table contains Subscriber-Network Interface (SNI) parameters and state variables, one entry per SIP port.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfSmdsSwSubEntry  

wfSmdsSwSubDelete 1.3.6.1.4.1.18.3.5.9.7.1.1.1
create/delete parameter, dflt = created
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfSmdsSwSubDisable 1.3.6.1.4.1.18.3.5.9.7.1.1.2
enable/disable parameter, dflt = enabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSmdsSwSubState 1.3.6.1.4.1.18.3.5.9.7.1.1.3
SMDS Switch state variable, Up, Down Init, Not Present
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfSmdsSwSubCct 1.3.6.1.4.1.18.3.5.9.7.1.1.4
cct number for this instance
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1023  

wfSmdsSwSubDisableHrtbtPoll 1.3.6.1.4.1.18.3.5.9.7.1.1.5
determine use of DXI heartbeat poll
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSmdsSwSubHrtbtPollAddr 1.3.6.1.4.1.18.3.5.9.7.1.1.6
determine if heartbeat poll messages are sent as as CPE or network (CSU/DSU) messages.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER cpe(1), net(2)  

wfSmdsSwSubHrtbtPollInterval 1.3.6.1.4.1.18.3.5.9.7.1.1.7
heartbeat polling messages get sent every this many seconds - we don't want the polling interval to be less than or equal to the no-acknowledgment timer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 6..2147483647  

wfSmdsSwSubHrtbtPollDownCount 1.3.6.1.4.1.18.3.5.9.7.1.1.8
if this many consecutive heartbeat polling messages go unacknowledged, log an event declaring the line down
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..10  

wfSmdsSwSubDisableNetMgmt 1.3.6.1.4.1.18.3.5.9.7.1.1.9
determine use of LMI network management
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSmdsSwSubInterfaceType 1.3.6.1.4.1.18.3.5.9.7.1.1.10
defines whether this interface is a SNI or SSI.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER sni(1), ssi(2)  

wfSmdsSwSubInterfaceIndex 1.3.6.1.4.1.18.3.5.9.7.1.1.11
The index number for the SSI/SNI. Each SNI in the network has a unique id. The value of this object identifies the SIP port interface for which this entry contains management information.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSmdsSwSubDisableL3PduChecks 1.3.6.1.4.1.18.3.5.9.7.1.1.12
Enable/Disable L3_PDU verification. Default is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSmdsSwSubDisableUsageGeneration 1.3.6.1.4.1.18.3.5.9.7.1.1.13
enable/disable usage data generation. Default is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSmdsSwSubDisableMIR 1.3.6.1.4.1.18.3.5.9.7.1.1.14
enable/disable MIR enforcement, default is disabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSmdsSwSubUnassignedSAs 1.3.6.1.4.1.18.3.5.9.7.1.1.15
The total number of SIP Level 3 PDUs discarded by the SMDS Switch because the Source Address was not assigned to the SNI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwSubSAScreenViolations 1.3.6.1.4.1.18.3.5.9.7.1.1.16
The number of SIP L3_PDUs that violated the address screen based on source address screening for an SNI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwSubDAScreenViolations 1.3.6.1.4.1.18.3.5.9.7.1.1.17
The total number of SIP Level 3 PDUs that violated the Destination Address Screening using either an Individual Address Screen or a Group Address Screen for the SNI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwSubNumPDUExceededMIR 1.3.6.1.4.1.18.3.5.9.7.1.1.18
The total number of SIP L3_PDUs that exceeded the MIR on this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwSubSipL3ReceivedIAs 1.3.6.1.4.1.18.3.5.9.7.1.1.19
The total number of individually addressed SIP Level 3 PDUs received by the SMDS Switch from the CPE. The total includes only unerrored L3PDUs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwSubSipL3ReceivedGAs 1.3.6.1.4.1.18.3.5.9.7.1.1.20
The total number of group addressed SIP Level 3 PDUs received by the SMDS Switch from the CPE. The total includes only unerrored L3PDUs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwSubSipL3UnrecIAs 1.3.6.1.4.1.18.3.5.9.7.1.1.21
The number of SIP Level 3 PDUs received by the SMDS Switch from the CPE that have an unknown, valid, individual SMDS Destination Address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwSubSipL3UnrecGAs 1.3.6.1.4.1.18.3.5.9.7.1.1.22
The number of SIP Level 3 PDUs received by the SMDS Switch from the CPE that have an unknown, valid, group SMDS Destination Address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwSubSipL3SentIAs 1.3.6.1.4.1.18.3.5.9.7.1.1.23
The number of individually addressed SIP Level 3 PDUs that have been sent by this SMDS Switch to the CPE.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwSubSipL3SentGAs 1.3.6.1.4.1.18.3.5.9.7.1.1.24
The number of group addressed SIP L3PDUs that have been sent by this SMDS Switch to the CPE.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwSubSipL3Errors 1.3.6.1.4.1.18.3.5.9.7.1.1.25
The total number of SIP Level 3 PDUs received by the SMDS Switch from the CPE that were discovered to have protocol errors.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwSubSipL3InvAddrTypes 1.3.6.1.4.1.18.3.5.9.7.1.1.26
The total number of SIP Level 3 PDUs received by the SMDS Switch from the CPE that had a value in the Source or Destination Address type subfield other than group or individual. Or if the Source Address type subfield value indicates a group address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwSubSipL3VersionSupport 1.3.6.1.4.1.18.3.5.9.7.1.1.27
A value which indicates the version(s) of SIP that this SNI supports. The value is a sum. This sum initially takes the value zero. For each version, V, that this interface supports, 2 raised to (V - 1) is added to the sum. For example, a port supporting versions 1 and 2 would have a value of (2^(1-1)+2^(2-1))=3. The SipL3VersionSupport is effectively a bit mask with Version 1 equal to the least significant bit (LSB).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER version(1)  

wfSmdsSwSubSAScrnViolationOccur 1.3.6.1.4.1.18.3.5.9.7.1.1.28
A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded as a result of a Source Address violation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfSmdsSwSubDAScrnViolationOccur 1.3.6.1.4.1.18.3.5.9.7.1.1.29
A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded as a result of a Destination Address violation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfSmdsSwSubUnassignedSAOccur 1.3.6.1.4.1.18.3.5.9.7.1.1.30
A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded as a result of a unassigned Source Address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfSmdsSwSubSAErrorOccur 1.3.6.1.4.1.18.3.5.9.7.1.1.31
A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because of a Source Address Field Format error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfSmdsSwSubDAErrorOccur 1.3.6.1.4.1.18.3.5.9.7.1.1.32
A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because of a Destination Address Field Format error.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfSmdsSwSubInvalidBASizeOccur 1.3.6.1.4.1.18.3.5.9.7.1.1.33
A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because of an invalid BASize field value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfSmdsSwSubInvalidHELenOccur 1.3.6.1.4.1.18.3.5.9.7.1.1.34
A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because of an invalid Header Extension Length Field value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfSmdsSwSubInvalidHEVerOccur 1.3.6.1.4.1.18.3.5.9.7.1.1.35
A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because of an invalid Header Extension Version element.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfSmdsSwSubInvalidHECarOccur 1.3.6.1.4.1.18.3.5.9.7.1.1.36
A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because of an invalid Header Extension Carrier element.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfSmdsSwSubInvalidHEPadOccur 1.3.6.1.4.1.18.3.5.9.7.1.1.37
A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because of an invalid Header Extension Pad element.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfSmdsSwSubBEtagOccur 1.3.6.1.4.1.18.3.5.9.7.1.1.38
A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because of a Beginning-End Tag mismatch.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfSmdsSwSubBAsizeNELenOccur 1.3.6.1.4.1.18.3.5.9.7.1.1.39
A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because the BAsize and Length fields are not equal.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfSmdsSwSubIncorrectLenOccur 1.3.6.1.4.1.18.3.5.9.7.1.1.40
A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because of an incorrect length.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfSmdsSwSubExceededMIROccur 1.3.6.1.4.1.18.3.5.9.7.1.1.41
A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because it exceeded the MIR.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfSmdsSwSubInBandMgmtDisable 1.3.6.1.4.1.18.3.5.9.7.1.1.42
In-Band Management enable/disable parameter. This attribute indicates whether the local WSNI (only) is enabled to run IP in Host mode, for in-band management purposes, in additional to being a switch interface. The default is disabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSmdsSwSubInBandMgmtLocalAddr 1.3.6.1.4.1.18.3.5.9.7.1.1.43
Special SMDS E.164 Individual address that identifies this local circuit. This attribute is only used when the wfSmdsSwSubInBandMgmtDisable attribute is set to ENABLED
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfSmdsSwSubInBandMgmtReceivedPDUs 1.3.6.1.4.1.18.3.5.9.7.1.1.44
The total number of individually addressed In-Band Management PDUs received by the SMDS Switch from the CPE. The total includes only unerrored PDUs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwSubInBandMgmtSentPDUs 1.3.6.1.4.1.18.3.5.9.7.1.1.45
The number of individually addressed In-Band Management PDUs that have been sent by this SMDS Switch to the CPE.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwSubInBandMgmtMaxLenErrors 1.3.6.1.4.1.18.3.5.9.7.1.1.46
The number of In-Band Management PDUs that have exceeded the MTU size configured for the line
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwSubInBandMgmtEncapsErrors 1.3.6.1.4.1.18.3.5.9.7.1.1.47
The number of In-Band Management PDUs that have invalid encapsulation schemes
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwSubGAPartialResolve 1.3.6.1.4.1.18.3.5.9.7.1.1.48
The number of times group addressed L3_PDU's could not be resolved due to congestion.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwSubDANotOnSni 1.3.6.1.4.1.18.3.5.9.7.1.1.49
The number of times a L3_PDU was discarded at the egress because the destination address was not assigned to the SNI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwEndpTable 1.3.6.1.4.1.18.3.5.9.7.2
The Parameters for the Endpoint table. An Endpoint is defined as an IP address, SMDS E.164 address pair. Endpoint ranges should never overlap.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfSmdsSwEndpEntry

wfSmdsSwEndpEntry 1.3.6.1.4.1.18.3.5.9.7.2.1
The parameters for a particular Endpoint.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfSmdsSwEndpEntry  

wfSmdsSwEndpDelete 1.3.6.1.4.1.18.3.5.9.7.2.1.1
Indication to delete this endpoint entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfSmdsSwEndpE164AddrHigh 1.3.6.1.4.1.18.3.5.9.7.2.1.2
The High end of the E.164 address range for this endpoint information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

wfSmdsSwEndpE164AddrDelta 1.3.6.1.4.1.18.3.5.9.7.2.1.3
The difference between wfSmdsSwEndpE164AddrHigh to the beginning of the endpoint information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

wfSmdsSwEndpInterfaceIndex 1.3.6.1.4.1.18.3.5.9.7.2.1.4
This number indicates which SNI the endpoint information refers to.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwInterfaceTable 1.3.6.1.4.1.18.3.5.9.7.3
This is the Interface Table. This table also holds the Maximum Information Rate (MIR) information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfSmdsSwInterfaceEntry

wfSmdsSwInterfaceEntry 1.3.6.1.4.1.18.3.5.9.7.3.1
This table defines the IP addresses and what interfaces they are associated with.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfSmdsSwInterfaceEntry  

wfSmdsSwInterfaceDelete 1.3.6.1.4.1.18.3.5.9.7.3.1.1
Indication to delete this interface entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfSmdsSwInterfaceType 1.3.6.1.4.1.18.3.5.9.7.3.1.2
This number determines whether the interface information refers to an SNI, SSI, or ICI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER sni(1), ssi(2)  

wfSmdsSwInterfaceIndex 1.3.6.1.4.1.18.3.5.9.7.3.1.3
This number indicates which SNI, SSI, or ICI the interface information refers to.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwInterfaceIpAddr 1.3.6.1.4.1.18.3.5.9.7.3.1.4
IP Address associated with the interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfSmdsSwInterfaceMIR 1.3.6.1.4.1.18.3.5.9.7.3.1.5
This number represents the MIR in octets per second.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSmdsSwInterfaceCurrentRate 1.3.6.1.4.1.18.3.5.9.7.3.1.6
This number indicates the current rate of traffic flow to the interface. The software updates this counter. When this attribute exceeds wfSmdsSwInterfaceMIR traffic to the interface is dropped. Periodically the sofware resets this counter to zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwAssocScrnTable 1.3.6.1.4.1.18.3.5.9.7.4
This list identifies the associated SNI addresses per individualand group address screen. Different addresses on an SNI may be associated with different individual and group address screens (one individual address screen per associated address on an SNI, and one group address screen per associated address on an SNI ).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfSmdsSwAssocScrnEntry

wfSmdsSwAssocScrnEntry 1.3.6.1.4.1.18.3.5.9.7.4.1
An SNI index, group and individual screening list index, and the associated addresses for the SNI for the address screens.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfSmdsSwAssocScrnEntry  

wfSmdsSwAssocScrnDelete 1.3.6.1.4.1.18.3.5.9.7.4.1.1
Indication to delete this associated screen entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfSmdsSwAssocScrnSniIndex 1.3.6.1.4.1.18.3.5.9.7.4.1.2
The value of this object identifies the SIP Port interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex, defined in RFC1213, for the same interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwAssocScrnAddrInd 1.3.6.1.4.1.18.3.5.9.7.4.1.3
The value of this object identifies one of the SMDS addresses for the SNI, identified by the wfSmdsSwAssocScrnSniIndex that belongs to this individual (or group) address screen (wfSmdsSwAssocScrnAddrInd). This list will contain both individual and group addresses, because this list is used for both Destination Address Screening and Source Address Screening; the destination address in the L3_PDU that is undergoing Source Address Screening may be either a group or individual address that is assigned to that SNI. One screen will have a maximum of 64 associated addresses; up to a maximum of 16 individual addresses identifying an SNI and up to a maximum of 48 group addresses identifying an SNI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

wfSmdsSwAssocScrnIndivIndex 1.3.6.1.4.1.18.3.5.9.7.4.1.4
The value of this object identifies the individual address screening list. There is at least one individual address screen and at most s individual address screens per SNI. The initial value of s is defined to be 4. In the future more screening lists per SNI may be allowed. The values of this object correspond to the values of wfSmdsSwIAScrnIndex in the wfSmdsSwIAScrnTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

wfSmdsSwAssocScrnGrpIndex 1.3.6.1.4.1.18.3.5.9.7.4.1.5
The value of this object identifies the group address screening list. There is at least one group address screen and at most s group address screens per SNI. The initial value of s is defined to be 4. In the future more screening lists per SNI may be allowed. The values of this object correspond to the values of wfSmdsSwGAScrnIndex in the wfSmdsSwGAScrnTable. This field applies only to individual addresses on the SNI because it applies only to destination address screening of group addresses.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

wfSmdsSwIAScrnTable 1.3.6.1.4.1.18.3.5.9.7.5
This list identifies the individual addresses that will be screened per individual address screen table. The are up to s (s is equal to 4) individual address screens per SNI and at least one individual address screen per SNI. The Individual Address Screens and the Group Address Screens together consist of up to n addresses. The initial value of n is defined as 128. In the future a value of n up to 2048 may be supported. The Individual Address Screen is used to perform Destination Address Screening for individually addressed data units and Source Address Screening for all data units. The Group Address Screen is used to perform Destination Address Screening for group addressed data units.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfSmdsSwIAScrnEntry

wfSmdsSwIAScrnEntry 1.3.6.1.4.1.18.3.5.9.7.5.1
An SNI index, a screening list index, the individual addresses to be screened for the individual address screen, and whether the screened address is valid or invalid.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfSmdsSwIAScrnEntry  

wfSmdsSwIAScrnDelete 1.3.6.1.4.1.18.3.5.9.7.5.1.1
Indication to delete this IA screen entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfSmdsSwIAScrnSniIndex 1.3.6.1.4.1.18.3.5.9.7.5.1.2
The value of this object identifies the SIP Port interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex, defined in RFC1213, for the same interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwIAScrnIndex 1.3.6.1.4.1.18.3.5.9.7.5.1.3
The value of this object identifies the individual address screening list. There are at least one individual address screen and at most s individual address screens per SNI. The initial value of s is defined to be 4. In the future more screening lists per SNI may be allowed. The values of this object correspond to the values of wfSmdsSwScrnIndex in the wfSmdsSwScrnTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

wfSmdsSwIAScrnAddr 1.3.6.1.4.1.18.3.5.9.7.5.1.4
The value of this object identifies one of the individual addresses to be screened for source and destination address screening for the SNI identified by the wfSmdsSwIAScrnSniIndex and for the particular individual address screen (wfSmdsSwIAScrnIndex).
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

wfSmdsSwGAScrnTable 1.3.6.1.4.1.18.3.5.9.7.6
This list identifies the group addresses that will be screened per group address screen table. The are up to s (s is equal to 4) group address screens per SNI and at least one group address screen per SNI. The Individual Address Screen and the Group Address Screen together consist of up to n addresses. The initial value of n is defined as 128. In the future a value of n up to 2048 may be supported. The Individual Address Screen is used to perform Destination Address Screening for individually addressed data units and Source Address Screening for all data units. The Group Address Screen is used to perform Destination Address Screening for group addressed data units.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfSmdsSwGAScrnEntry

wfSmdsSwGAScrnEntry 1.3.6.1.4.1.18.3.5.9.7.6.1
An SNI index, a screening list index, the group addresses to be screened for the group address screen, and whether the screened address is valid or invalid.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfSmdsSwGAScrnEntry  

wfSmdsSwGAScrnDelete 1.3.6.1.4.1.18.3.5.9.7.6.1.1
Indication to delete this GA screen entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfSmdsSwGAScrnSniIndex 1.3.6.1.4.1.18.3.5.9.7.6.1.2
The value of this object identifies the SIP Port interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex, defined in RFC1213, for the same interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwGAScrnIndex 1.3.6.1.4.1.18.3.5.9.7.6.1.3
The value of this object identifies the group address screening list. There is at least one group address screen and at most s group address screens per SNI. The initial value of s is defined to be 4. In the future more screening lists per SNI may be allowed. The values of this object correspond to the values of wfSmdsSwScrnIndex in the wfSmdsSwSmdsScrnTable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..4  

wfSmdsSwGAScrnAddr 1.3.6.1.4.1.18.3.5.9.7.6.1.4
The value of this object identifies one of the group addresses to be screened for destination address screening for the SNI identified by the wfSmdsSwGAScrnSniIndex and for the particular group address screen (wfSmdsSwGAScrnIndex).
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

wfSmdsSwGATable 1.3.6.1.4.1.18.3.5.9.7.7
A table of all group addresses in the network and the associated individual addresses identified by each group address. A group address identifies up to m individual addresses. An SMDS SS supports up to n group addresses. A group address can be identified by up to p individual addresses. A particular SNI is identified by up to 48 group addresses. The initial values of m, n, and p are defined as 128, 1024, and 32, respectively. In the future values of m and n of 2048 and 8192, respectively, may be supported.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfSmdsSwGAEntry

wfSmdsSwGAEntry 1.3.6.1.4.1.18.3.5.9.7.7.1
A Group Address and an address in that group and whether that association is valid or invalid.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfSmdsSwGAEntry  

wfSmdsSwGADelete 1.3.6.1.4.1.18.3.5.9.7.7.1.1
Indication to delete this group address entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfSmdsSwGASSI 1.3.6.1.4.1.18.3.5.9.7.7.1.2
The SSI associated with this Group Address. An SSI of 0 is used to indicate that all interfaces can use the group address. An SSI other than 0 indicates that only the SSI, or an SNI associated with the SSI should use the group.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwGAGroupAddress 1.3.6.1.4.1.18.3.5.9.7.7.1.3
A Group Address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

wfSmdsSwGAGroupMember 1.3.6.1.4.1.18.3.5.9.7.7.1.4
An individual SMDS address that belongs to this Group Address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

wfSmdsSwCurUsageTable 1.3.6.1.4.1.18.3.5.9.7.8
This table contains the Current Usage Data. This is the interface between Billing and Switching. The Switch gates create these records. The Billing gates collect them to create billing data.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfSmdsSwCurUsageEntry

wfSmdsSwCurUsageEntry 1.3.6.1.4.1.18.3.5.9.7.8.1
The usage data for the current usage period indexed by destination,source address.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfSmdsSwCurUsageEntry  

wfSmdsSwCurUsageDelete 1.3.6.1.4.1.18.3.5.9.7.8.1.1
Indication to delete this current usage entry.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfSmdsSwCurUsageSni 1.3.6.1.4.1.18.3.5.9.7.8.1.2
The SNI number of the interface generating the usage information
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

wfSmdsSwCurUsageDestAddr 1.3.6.1.4.1.18.3.5.9.7.8.1.3
The destination address of a SMDS group or individual E.164 address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

wfSmdsSwCurUsageSrcAddr 1.3.6.1.4.1.18.3.5.9.7.8.1.4
The source address of a SMDS individual E.164 address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

wfSmdsSwCurUsageGrpIndAddr 1.3.6.1.4.1.18.3.5.9.7.8.1.5
When the destination address of an L3_PDU is a group address, this attribute is set to one of the E.164 individual addresses that is in the group address and on the destination SNI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfSmdsSwCurUsageNumL3Pdu 1.3.6.1.4.1.18.3.5.9.7.8.1.6
This number represents the number of billable L3_PDUs counted by the circuit during the most recent collection interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwCurUsageNumOctet 1.3.6.1.4.1.18.3.5.9.7.8.1.7
This number represents the number of billable octets counted by the circuit during the most recent collection interval.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfSmdsSwCurUsageToBeDeleted 1.3.6.1.4.1.18.3.5.9.7.8.1.8
Indication to billing to delete this current usage entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfSmdsSwUsage 1.3.6.1.4.1.18.3.5.9.7.9
OBJECT IDENTIFIER    

wfSmdsSwUsageEnable 1.3.6.1.4.1.18.3.5.9.7.9.1
Enable/Disable SMDS_SW billing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSmdsSwUsageVolume 1.3.6.1.4.1.18.3.5.9.7.9.2
Indicates the file system volume number to which the billing usage data files will be written. The volume number corresponds to the slot number on which the volume resides. Note: Value 0 has the special meaning that no 'Store' and 'Flush' operations will take place. This translates to no Billing data will be written to the local file system. 'Update' operations will still be performed on each local slot. Full Billing statistics will still be available in the wfSmdsSwUsageTable MIB.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..14  

wfSmdsSwUsageVolumeBackup 1.3.6.1.4.1.18.3.5.9.7.9.3
Indicates the backup volume if wfSmdsSwUsageVolume becomes inoperative. Note: This feature is not implemented in this release.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..14  

wfSmdsSwUsageDirectory 1.3.6.1.4.1.18.3.5.9.7.9.4
The name of the directory where the billing usage data files are stored.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfSmdsSwUsageFilePrefix 1.3.6.1.4.1.18.3.5.9.7.9.5
The base name of billing usage data files.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfSmdsSwUsageTimerInterval 1.3.6.1.4.1.18.3.5.9.7.9.6
This number determines the timer interval (number of seconds) unit for the Billing process to perform its various timer driven tasks. i.e. updating billing usage data, writing billing usage data to file system and file system management activities.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..60  

wfSmdsSwUsageUpdateInterval 1.3.6.1.4.1.18.3.5.9.7.9.7
This number specifies the interval (number of minutes) for the Billing process to collect and update billing usage data in the wfSmdsSwUsage MIB. Note: When converted to seconds, this must be a multiple of wfSmdsSwUsageTimerInterval.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..2147483647  

wfSmdsSwUsageStoreInterval 1.3.6.1.4.1.18.3.5.9.7.9.8
This number specifies the interval (number of minutes) for the Billing process to write billing usage data on to the file system from the wfSmdsSwUsage MIB. Note: When converted to seconds, this must be a multiple of wfSmdsSwUsageTimerInterval.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..2147483647  

wfSmdsSwUsageFlushInterval 1.3.6.1.4.1.18.3.5.9.7.9.9
This number specifies the interval (number of minutes) for the Billing process to write billing usage data on to the file system from the wfSmdsSwUsage MIB followed by zeroing the wfSmdsSwUsage MIB. Note: When converted to seconds, this must be a multiple of wfSmdsSwUsageTimerInterval.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..2147483647  

wfSmdsSwUsageCleanupInterval 1.3.6.1.4.1.18.3.5.9.7.9.10
This is the interval (number of minutes) for the Billing process to check and delete old billing usage data files. Note: When converted to seconds, this must be a multilple of wfSmdsSwUsageTimerInterval.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..2147483647  

wfSmdsSwUsageLocalTimeZone 1.3.6.1.4.1.18.3.5.9.7.9.11
Indicates local time zone of the switch
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageUpdateTimeStamp 1.3.6.1.4.1.18.3.5.9.7.9.12
Time stamp of last wfSmdsSwUsageUpdateInterval timer expiration or the starting time of the current wfSmdsSwUsageUpdateInterval. This value is number of seconds since midnight Jan 1, 1976 (GMT).
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

wfSmdsSwUsageStoreTimeStamp 1.3.6.1.4.1.18.3.5.9.7.9.13
Time stamp of last wfSmdsSwUsageStoreInterval timer expiration or the starting time of the current wfSmdsSwUsageStoreInterval. This value is number of seconds since midnight Jan. 1, 1976 (GMT).
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

wfSmdsSwUsageFlushTimeStamp 1.3.6.1.4.1.18.3.5.9.7.9.14
Time stamp of last wfSmdsSwUsageFlushInterval timer expiration or the starting time of the current wfSmdsSwUsageFlushInterval. This value is number of seconds since midnight Jan. 1, 1976 (GMT).
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

wfSmdsSwUsageCleanupTimeStamp 1.3.6.1.4.1.18.3.5.9.7.9.15
Time stamp of last wfSmdsSwUsageCleanupInterval timer expiration or the starting time of the current wfSmdsSwUsageCleanupInterval. This value is number of seconds since midnight Jan. 1, 1976 (GMT).
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

wfSmdsSwUsageUpdateData 1.3.6.1.4.1.18.3.5.9.7.9.16
Setting this attribute to a non-zero value will cause an immediate updating of the billing usage data. Once activated, this attribute should be reset to zero to allow subsequent activations.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageStoreData 1.3.6.1.4.1.18.3.5.9.7.9.17
Setting this attribute to a non-zero value will cause an immediate updating and writing of the billing usage data. Once activated, this attribute should be reset to zero to allow subsequent activations.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageFlushData 1.3.6.1.4.1.18.3.5.9.7.9.18
Setting this attribute to a non-zero value will cause an immediate updating and writing of the billing usage data and followed by zeroing the wfSmdsSwBillingUsage MIB. Once activated, this attribute should be reset to zero to allow subsequent activations.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageFileCleanup 1.3.6.1.4.1.18.3.5.9.7.9.19
Setting this attribute to a non-zero value will cause an immediate checking and deleting old billing usage data files. Once activated, this attribute should be reset to zero to allow subsequent activations.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageState 1.3.6.1.4.1.18.3.5.9.7.9.20
current state of SMDS_SW billing.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfSmdsSwUsageCurVolume 1.3.6.1.4.1.18.3.5.9.7.9.21
current file system volume number used. This number is the same as wfSmdsSwUsageVolume except when the user sets wfSmdsSwUsageVolume to an invalid number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..14  

wfSmdsSwUsageCurVolumeBackup 1.3.6.1.4.1.18.3.5.9.7.9.22
curent backup file system volume number used. This number is the same as wfSmdsSwUsageVolumeBackUp except when the user sets wfSmdsSwUsageVolume to an invalid number. Note: This feature is not implemented in this release.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..14  

wfSmdsSwUsageCurDirectory 1.3.6.1.4.1.18.3.5.9.7.9.23
current directory name used. This number is the same as wfSmdsSwUsageDirectory except when the user sets wfSmdsSwUsageDirectory to an invalid name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfSmdsSwUsageCurFilePrefix 1.3.6.1.4.1.18.3.5.9.7.9.24
current base file name used. This number is the same as wfSmdsSwUsageFilePrefix except when the user sets wfSmdsSwUsageFilePrefix to an invalid name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfSmdsSwUsageCurTimerInterval 1.3.6.1.4.1.18.3.5.9.7.9.25
current timer interval number used. This number is the same as wfSmdsSwUsageTimerInterval except when the user sets wfSmdsSwUsageTimerInterval to an invalid value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..60  

wfSmdsSwUsageCurUpdateInterval 1.3.6.1.4.1.18.3.5.9.7.9.26
current update interval number used. This number is the same as wfSmdsSwUsageUpdateInterval except when the user sets wfSmdsSwUsageUpdateInterval to an invalid value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

wfSmdsSwUsageCurStoreInterval 1.3.6.1.4.1.18.3.5.9.7.9.27
current store timer interval number used. This number is the same as wfSmdsSwUsageStoreInterval except when the user sets wfSmdsSwUsageStoreInterval to an invalid value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

wfSmdsSwUsageCurFlushInterval 1.3.6.1.4.1.18.3.5.9.7.9.28
current flush timer interval number used. This number is the same as wfSmdsSwUsageFlushInterval except when the user sets wfSmdsSwUsageFlushInterval to an invalid value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

wfSmdsSwUsageCurCleanupInterval 1.3.6.1.4.1.18.3.5.9.7.9.29
current file cleanup timer interval number used. This number is the same as wfSmdsSwUsageCleanupInterval except when the user sets wfSmdsSwUsageCleanupInterval to an invalid value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..2147483647  

wfSmdsSwUsageDebug 1.3.6.1.4.1.18.3.5.9.7.9.30
Enable/Disable printing of debug edl (trap) messages. NOTE: Do not enable this attribute in operational enviornment as it will likely flood the logging facility. This attribute is reserved for specialized debugging in a controlled lab enviornment.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSmdsSwUsageCurDebug 1.3.6.1.4.1.18.3.5.9.7.9.31
current debug value used. This value is the same as wfSmdsSwUsageDebug except when the user sets wfSmdsSwUsageDeubg to an invalid value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSmdsSwUsageSwitchId 1.3.6.1.4.1.18.3.5.9.7.9.32
switch id used in the billing usage data file.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageNumEntries 1.3.6.1.4.1.18.3.5.9.7.9.33
number of entries in wfSmdsSwUsageTable
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageTable 1.3.6.1.4.1.18.3.5.9.7.10
The Billing Usage Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfSmdsSwUsageEntry

wfSmdsSwUsageEntry 1.3.6.1.4.1.18.3.5.9.7.10.1
The parameters for Billing Usage.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfSmdsSwUsageEntry  

wfSmdsSwUsageDelete 1.3.6.1.4.1.18.3.5.9.7.10.1.1
Indicates status of this entry. SMDS_SW_USAGE_CREATED is the normal case. SMDS_SW_USAGE_DELETED means this billing instance will be deleted at the end of the next wfSmdsSwUsageFlush period after this billing record is written out to the file system.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfSmdsSwUsageSni 1.3.6.1.4.1.18.3.5.9.7.10.1.2
The circuit number of the interface generating the usage information
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageDestAddr 1.3.6.1.4.1.18.3.5.9.7.10.1.3
Instance identifier; the destination address of an L3_PDU. The SMDS Switch collects usage data based on the destination/source address pair.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

wfSmdsSwUsageSrcAddr 1.3.6.1.4.1.18.3.5.9.7.10.1.4
Instance identifier; the source address of an L3_PDU. The SMDS Switch collects usage data based on the destination/source address pair.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

wfSmdsSwUsageStartTimeStampHigh 1.3.6.1.4.1.18.3.5.9.7.10.1.5
Time stamp of the starting time (the high 32 bits) of last billing usage interval. This value is the number of 1/100th seconds since midnight Jan 1, 1976 (GMT).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageStartTimeStampLow 1.3.6.1.4.1.18.3.5.9.7.10.1.6
Time stamp of the starting time (the low 32 bits) of last billing usage interval. This value is the number of 1/100th seconds since midnight Jan 1, 1976 (GMT).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageEndTimeStampHigh 1.3.6.1.4.1.18.3.5.9.7.10.1.7
Time stamp of the ending time (the high 32 bits) of last billing usage interval. This value is the number of 1/100th seconds since midnight Jan 1, 1976 (GMT).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageEndTimeStampLow 1.3.6.1.4.1.18.3.5.9.7.10.1.8
Time stamp of the ending time (the low 32 bits) of last billing usage interval. This value is the number of 1/100th seconds since midnight Jan 1, 1976 (GMT).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageSentL3PduHigh 1.3.6.1.4.1.18.3.5.9.7.10.1.9
Number (the high 32 bits) of L3_PDUs sent to the CPE between wfSmdsSwUsageStartTimeStamp and wfSmdsSwUsageEndTimeStamp.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageSentL3PduLow 1.3.6.1.4.1.18.3.5.9.7.10.1.10
Number (the low 32 bits) of L3_PDUs sent to the CPE between wfSmdsSwUsageStartTimeStamp and wfSmdsSwUsageEndTimeStamp.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageSentOctetHigh 1.3.6.1.4.1.18.3.5.9.7.10.1.11
Number (the high 32 bits) of octets sent to the CPE between wfSmdsSwUsageStartTimeStamp and wfSmdsSwUsageEndTimeStamp.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageSentOctetLow 1.3.6.1.4.1.18.3.5.9.7.10.1.12
Number (the low 32 bits) of octets sent to the CPE between wfSmdsSwUsageStartTimeStamp and wfSmdsSwUsageEndTimeStamp.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageLastL3PduHigh 1.3.6.1.4.1.18.3.5.9.7.10.1.13
The (high 32 bits) value of wfSmdsSwCurUsageNumL3Pdu value at wfSmdsSwUsageEndTimeStamp. Note: Since wfSmdsSwCurUsageNumL3Pdu is a 32-bit COUNTER, this is really a counter keeping track of number of times wfSmdsSwCurUsageNumL3Pdu has wrapped around.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageLastL3PduLow 1.3.6.1.4.1.18.3.5.9.7.10.1.14
The (low 32 bits) value of wfSmdsSwCurUsageNumL3Pdu value at wfSmdsSwUsageEndTimeStamp.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageLastOctetHigh 1.3.6.1.4.1.18.3.5.9.7.10.1.15
The (high 32 bits) value of wfSmdsSwCurUsageNumOctets value at wfSmdsSwUsageEndTimeStamp. Note: Since wfSmdsSwCurUsageNumOctets is a 32-bit COUNTER, this is really a counter keeping track of number of times wfSmdsSwCurUsageNumOctets has wrapped around.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageLastOctetLow 1.3.6.1.4.1.18.3.5.9.7.10.1.16
The (low 32 bits) value of wfSmdsSwCurUsageNumOctets value at wfSmdsSwUsageEndTimeStamp.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwUsageGrpIndAddr 1.3.6.1.4.1.18.3.5.9.7.10.1.17
When the destination address of an L3_PDU is a group address, this attribute is set to one of the E.164 individual addresses that is in the group address and on the destination SNI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfSmdsSwSsiSniTable 1.3.6.1.4.1.18.3.5.9.7.11
The Parameters for the SSI/SNI Object. This object associates SNI's with SSI's for Bellcore TR-TSV-001239 compliance.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfSmdsSwSsiSniEntry

wfSmdsSwSsiSniEntry 1.3.6.1.4.1.18.3.5.9.7.11.1
The parameters for a particular SSI/SNI.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfSmdsSwSsiSniEntry  

wfSmdsSwSsiSniDelete 1.3.6.1.4.1.18.3.5.9.7.11.1.1
Indication to delete this SSI/SNI entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfSmdsSwSsiSniSSI 1.3.6.1.4.1.18.3.5.9.7.11.1.2
An SSI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSmdsSwSsiSniSNI 1.3.6.1.4.1.18.3.5.9.7.11.1.3
An SNI.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER