Wellfleet-RSVP-MIB

File: Wellfleet-RSVP-MIB.mib (130083 bytes)

Imported modules

RFC-1212 RFC1155-SMI Wellfleet-COMMON-MIB

Imported symbols

OBJECT-TYPE IpAddress Gauge
wfReservationProtocolGroup

Defined Types

WfRsvpSessionEntry  
SEQUENCE    
  wfRsvpSessionDestAddr IpAddress
  wfRsvpSessionDestAddrLength INTEGER
  wfRsvpSessionProtocol INTEGER
  wfRsvpSessionPort INTEGER
  wfRsvpSessionSenders Gauge
  wfRsvpSessionReceivers Gauge
  wfRsvpSessionRequests Gauge

WfRsvpSenderEntry  
SEQUENCE    
  wfRsvpSenderDestAddr IpAddress
  wfRsvpSenderAddr IpAddress
  wfRsvpSenderDestAddrLength INTEGER
  wfRsvpSenderAddrLength INTEGER
  wfRsvpSenderProtocol INTEGER
  wfRsvpSenderDestPort INTEGER
  wfRsvpSenderPort INTEGER
  wfRsvpSenderHopAddr IpAddress
  wfRsvpSenderHopLih INTEGER
  wfRsvpSenderInterface INTEGER
  wfRsvpSenderTSpecRate INTEGER
  wfRsvpSenderTSpecPeakRate INTEGER
  wfRsvpSenderTSpecBurst INTEGER
  wfRsvpSenderTSpecMinTU INTEGER
  wfRsvpSenderTSpecMaxTU INTEGER
  wfRsvpSenderInterval INTEGER
  wfRsvpSenderRSVPHop INTEGER
  wfRsvpSenderLastChange INTEGER
  wfRsvpSenderPSBTimeout INTEGER
  wfRsvpSenderPolicy OCTET STRING
  wfRsvpSenderAdspecBreak INTEGER
  wfRsvpSenderAdspecHopCount INTEGER
  wfRsvpSenderAdspecPathBw INTEGER
  wfRsvpSenderAdspecMinLatency INTEGER
  wfRsvpSenderAdspecMtu INTEGER
  wfRsvpSenderAdspecGSSvc INTEGER
  wfRsvpSenderAdspecGSBreak INTEGER
  wfRsvpSenderAdspecGSCtot INTEGER
  wfRsvpSenderAdspecGSDtot INTEGER
  wfRsvpSenderAdspecGSCsum INTEGER
  wfRsvpSenderAdspecGSDsum INTEGER
  wfRsvpSenderAdspecGSHopCount INTEGER
  wfRsvpSenderAdspecGSPathBw INTEGER
  wfRsvpSenderAdspecGSMinLatency INTEGER
  wfRsvpSenderAdspecGSMtu INTEGER
  wfRsvpSenderAdspecCLSvc INTEGER
  wfRsvpSenderAdspecCLBreak INTEGER
  wfRsvpSenderAdspecCLHopCount INTEGER
  wfRsvpSenderAdspecCLPathBw INTEGER
  wfRsvpSenderAdspecCLMinLatency INTEGER
  wfRsvpSenderAdspecCLMtu INTEGER
  wfRsvpSenderStatus INTEGER

WfRsvpResvEntry  
SEQUENCE    
  wfRsvpResvDestAddr IpAddress
  wfRsvpResvSenderAddr IpAddress
  wfRsvpResvDestAddrLength INTEGER
  wfRsvpResvSenderAddrLength INTEGER
  wfRsvpResvProtocol INTEGER
  wfRsvpResvDestPort INTEGER
  wfRsvpResvPort INTEGER
  wfRsvpResvHopAddr IpAddress
  wfRsvpResvHopLih INTEGER
  wfRsvpResvInterface INTEGER
  wfRsvpResvService INTEGER
  wfRsvpResvTSpecRate INTEGER
  wfRsvpResvTSpecPeakRate INTEGER
  wfRsvpResvTSpecBurst INTEGER
  wfRsvpResvTSpecMinTU INTEGER
  wfRsvpResvTSpecMaxTU INTEGER
  wfRsvpResvTSpecLevel INTEGER
  wfRsvpResvRSpecRate INTEGER
  wfRsvpResvRSpecSlack INTEGER
  wfRsvpResvInterval INTEGER
  wfRsvpResvScope OCTET STRING
  wfRsvpResvShared INTEGER
  wfRsvpResvExplicit INTEGER
  wfRsvpResvRSVPHop INTEGER
  wfRsvpResvLastChange INTEGER
  wfRsvpResvRSBTimeout INTEGER
  wfRsvpResvPolicy OCTET STRING
  wfRsvpResvStatus INTEGER

WfRsvpResvFwdEntry  
SEQUENCE    
  wfRsvpResvFwdDestAddr IpAddress
  wfRsvpResvFwdSenderAddr IpAddress
  wfRsvpResvFwdDestAddrLength INTEGER
  wfRsvpResvFwdSenderAddrLength INTEGER
  wfRsvpResvFwdProtocol INTEGER
  wfRsvpResvFwdDestPort INTEGER
  wfRsvpResvFwdPort INTEGER
  wfRsvpResvFwdHopAddr IpAddress
  wfRsvpResvFwdHopLih INTEGER
  wfRsvpResvFwdInterface INTEGER
  wfRsvpResvFwdService INTEGER
  wfRsvpResvFwdTSpecRate INTEGER
  wfRsvpResvFwdTSpecPeakRate INTEGER
  wfRsvpResvFwdTSpecBurst INTEGER
  wfRsvpResvFwdTSpecMinTU INTEGER
  wfRsvpResvFwdTSpecMaxTU INTEGER
  wfRsvpResvFwdTSpecLevel INTEGER
  wfRsvpResvFwdRSpecRate INTEGER
  wfRsvpResvFwdRSpecSlack INTEGER
  wfRsvpResvFwdInterval INTEGER
  wfRsvpResvFwdScope OCTET STRING
  wfRsvpResvFwdShared INTEGER
  wfRsvpResvFwdExplicit INTEGER
  wfRsvpResvFwdRSVPHop INTEGER
  wfRsvpResvFwdLastChange INTEGER
  wfRsvpResvFwdPolicy OCTET STRING
  wfRsvpResvFwdStatus INTEGER

WfRsvpIfEntry  
SEQUENCE    
  wfRsvpIfDelete INTEGER
  wfRsvpIfEnable INTEGER
  wfRsvpIfState INTEGER
  wfRsvpIfCct INTEGER
  wfRsvpIfUdpNbrs Gauge
  wfRsvpIfIpNbrs Gauge
  wfRsvpIfNbrs Gauge
  wfRsvpIfRefreshBlockadeMultiple INTEGER
  wfRsvpIfRefreshMultiple INTEGER
  wfRsvpIfTTL INTEGER
  wfRsvpIfRefreshInterval INTEGER
  wfRsvpIfRouteDelay INTEGER
  wfRsvpIfUdpRequired INTEGER

WfRsvpNbrEntry  
SEQUENCE    
  wfRsvpNbrAddress IpAddress
  wfRsvpNbrProtocol INTEGER
  wfRsvpNbrCct INTEGER
  wfRsvpNbrStatus INTEGER

WfSRsvpSenderEntry  
SEQUENCE    
  wfSRsvpSenderCreate INTEGER
  wfSRsvpSenderEnable INTEGER
  wfSRsvpSenderStatus INTEGER
  wfSRsvpSenderNumber INTEGER
  wfSRsvpSenderDestReplicate INTEGER
  wfSRsvpSenderReplicate INTEGER
  wfSRsvpSenderIntegrity OCTET STRING
  wfSRsvpSenderDestAddr IpAddress
  wfSRsvpSenderAddr IpAddress
  wfSRsvpSenderDestAddrLength INTEGER
  wfSRsvpSenderAddrLength INTEGER
  wfSRsvpSenderProtocol INTEGER
  wfSRsvpSenderDestPort INTEGER
  wfSRsvpSenderPort INTEGER
  wfSRsvpSenderHopAddr IpAddress
  wfSRsvpSenderHopLih INTEGER
  wfSRsvpSenderInterface INTEGER
  wfSRsvpSenderTimeValue INTEGER
  wfSRsvpSenderTSpecRate INTEGER
  wfSRsvpSenderTSpecPeakRate INTEGER
  wfSRsvpSenderTSpecBurst INTEGER
  wfSRsvpSenderTSpecMinTU INTEGER
  wfSRsvpSenderTSpecMaxTU INTEGER
  wfSRsvpSenderPolicy OCTET STRING
  wfSRsvpSenderAdspec INTEGER
  wfSRsvpSenderAdspecBreak INTEGER
  wfSRsvpSenderAdspecHopCount INTEGER
  wfSRsvpSenderAdspecPathBw INTEGER
  wfSRsvpSenderAdspecMinLatency INTEGER
  wfSRsvpSenderAdspecMtu INTEGER
  wfSRsvpSenderAdspecGSSvc INTEGER
  wfSRsvpSenderAdspecGSBreak INTEGER
  wfSRsvpSenderAdspecGSCtot INTEGER
  wfSRsvpSenderAdspecGSDtot INTEGER
  wfSRsvpSenderAdspecGSCsum INTEGER
  wfSRsvpSenderAdspecGSDsum INTEGER
  wfSRsvpSenderAdspecGSOverrides INTEGER
  wfSRsvpSenderAdspecGSHopCount INTEGER
  wfSRsvpSenderAdspecGSPathBw INTEGER
  wfSRsvpSenderAdspecGSMinLatency INTEGER
  wfSRsvpSenderAdspecGSMtu INTEGER
  wfSRsvpSenderAdspecCLSvc INTEGER
  wfSRsvpSenderAdspecCLBreak INTEGER
  wfSRsvpSenderAdspecCLOverrides INTEGER
  wfSRsvpSenderAdspecCLHopCount INTEGER
  wfSRsvpSenderAdspecCLPathBw INTEGER
  wfSRsvpSenderAdspecCLMinLatency INTEGER
  wfSRsvpSenderAdspecCLMtu INTEGER

WfSRsvpResvEntry  
SEQUENCE    
  wfSRsvpResvCreate INTEGER
  wfSRsvpResvEnable INTEGER
  wfSRsvpResvStatus INTEGER
  wfSRsvpResvNumber INTEGER
  wfSRsvpResvDestReplicate INTEGER
  wfSRsvpResvReplicate INTEGER
  wfSRsvpResvIntegrity OCTET STRING
  wfSRsvpResvDestAddr IpAddress
  wfSRsvpResvSenderAddr IpAddress
  wfSRsvpResvDestAddrLength INTEGER
  wfSRsvpResvSenderAddrLength INTEGER
  wfSRsvpResvProtocol INTEGER
  wfSRsvpResvDestPort INTEGER
  wfSRsvpResvPort INTEGER
  wfSRsvpResvFilterSpecNum INTEGER
  wfSRsvpResvHopAddr IpAddress
  wfSRsvpResvHopLih INTEGER
  wfSRsvpResvInterface INTEGER
  wfSRsvpResvTimeValue INTEGER
  wfSRsvpResvService INTEGER
  wfSRsvpResvTSpecRate INTEGER
  wfSRsvpResvTSpecPeakRate INTEGER
  wfSRsvpResvTSpecBurst INTEGER
  wfSRsvpResvTSpecMinTU INTEGER
  wfSRsvpResvTSpecMaxTU INTEGER
  wfSRsvpResvTSpecLevel INTEGER
  wfSRsvpResvRSpecRate INTEGER
  wfSRsvpResvRSpecSlack INTEGER
  wfSRsvpResvScopeNum INTEGER
  wfSRsvpResvScope OCTET STRING
  wfSRsvpResvShared INTEGER
  wfSRsvpResvExplicit INTEGER
  wfSRsvpResvPolicy OCTET STRING

Defined Values

wfRsvpGroup 1.3.6.1.4.1.18.3.5.16.1.1
OBJECT IDENTIFIER    

wfRsvp 1.3.6.1.4.1.18.3.5.16.1.1.1
OBJECT IDENTIFIER    

wfRsvpDelete 1.3.6.1.4.1.18.3.5.16.1.1.1.1
Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete Rsvp.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfRsvpDisable 1.3.6.1.4.1.18.3.5.16.1.1.1.2
Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable Rsvp.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfRsvpState 1.3.6.1.4.1.18.3.5.16.1.1.1.3
The current state of Rsvp.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpres(4)  

wfRsvpSoloistSlots 1.3.6.1.4.1.18.3.5.16.1.1.1.4
Slot mask for which slot(s) RSVP Soloist is eligible to run on. The MSBit represents slot 1, the next most significant bit represents slot 2, and so on... Slots can be 1-14. Default is all slots on a BCN.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge 0..4294967295  

wfRsvpInfoLogFilter 1.3.6.1.4.1.18.3.5.16.1.1.1.5
Turn RSVP log ON or OFF for RSVP informational and warning messages. The bit position is used to represent a RSVP module: RSVP_LOG_RIF_PROCESSING 0x0001 - RIF processing. RSVP_LOG_SOLO_PROCESSING 0x0002 - SOLO processing. RSVP_LOG_ROUTE_INTF_PROCESSING 0x0004 - ROUTE interface processing. RSVP_LOG_MERGE_PROCESSING 0x0008 - MERGE processing. RSVP_LOG_DB_PROCESSING 0x0010 - database access processing. RSVP_LOG_INTSERV_INTF_PROCESSING 0x0020 - INTSERV interface processing. RSVP_LOG_CRM_INTF_PROCESSING 0x0040 - CRM interface processing. RSVP_LOG_STATIC_RSVP 0x0080 - STATIC RSVP processing. RSVP_LOG_CONTROL_PROCESSING 0x0100 - CONTROL processing. RSVP_LOG_MAP_VEC_PROCESSING 0x0200 - MAP VECTOR processing. RSVP_LOG_PROXY_PROCESSING 0x0400 - RSVP MIB PROXY processing. RSVP_LOG_REFRESH_PROCESSING 0x0800 - Path/Resv Refresh processing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfRsvpDebugLogFilter 1.3.6.1.4.1.18.3.5.16.1.1.1.6
Turn RSVP log ON or OFF for RSVP debugging messages. The bit position is used to represent a RSVP module: RSVP_LOG_RIF_PROCESSING 0x0001 - RIF processing. RSVP_LOG_SOLO_PROCESSING 0x0002 - SOLO processing. RSVP_LOG_ROUTE_INTF_PROCESSING 0x0004 - ROUTE interface processing. RSVP_LOG_MERGE_PROCESSING 0x0008 - MERGE processing. RSVP_LOG_DB_PROCESSING 0x0010 - database access processing. RSVP_LOG_INTSERV_INTF_PROCESSING 0x0020 - INTSERV interface processing. RSVP_LOG_CRM_INTF_PROCESSING 0x0040 - CRM interface processing. RSVP_LOG_STATIC_RSVP 0x0080 - STATIC RSVP processing. RSVP_LOG_CONTROL_PROCESSING 0x0100 - CONTROL processing. RSVP_LOG_MAP_VEC_PROCESSING 0x0200 - MAP VECTOR processing. RSVP_LOG_PROXY_PROCESSING 0x0400 - RSVP MIB PROXY processing. RSVP_LOG_REFRESH_PROCESSING 0x0800 - Path/Resv Refresh processing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfRsvpTraceLogFilter 1.3.6.1.4.1.18.3.5.16.1.1.1.7
Turn RSVP log ON or OFF for RSVP trace messages. The bit position is used to represent a RSVP module: RSVP_LOG_RIF_PROCESSING 0x0001 - RIF processing. RSVP_LOG_SOLO_PROCESSING 0x0002 - SOLO processing. RSVP_LOG_ROUTE_INTF_PROCESSING 0x0004 - ROUTE interface processing. RSVP_LOG_MERGE_PROCESSING 0x0008 - MERGE processing. RSVP_LOG_DB_PROCESSING 0x0010 - database access processing. RSVP_LOG_INTSERV_INTF_PROCESSING 0x0020 - INTSERV interface processing. RSVP_LOG_CRM_INTF_PROCESSING 0x0040 - CRM interface processing. RSVP_LOG_STATIC_RSVP 0x0080 - STATIC RSVP processing. RSVP_LOG_CONTROL_PROCESSING 0x0100 - CONTROL processing. RSVP_LOG_MAP_VEC_PROCESSING 0x0200 - MAP VECTOR processing. RSVP_LOG_PROXY_PROCESSING 0x0400 - RSVP MIB PROXY processing. RSVP_LOG_REFRESH_PROCESSING 0x0800 - Path/Resv Refresh processing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfRsvpTotalSenders 1.3.6.1.4.1.18.3.5.16.1.1.1.8
The total number of Sender (PATH) states in the router.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge 0..4294967295  

wfRsvpTotalReservations 1.3.6.1.4.1.18.3.5.16.1.1.1.9
The total number of Reservation (RESV) states in the router.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge 0..4294967295  

wfRsvpTotalReserved 1.3.6.1.4.1.18.3.5.16.1.1.1.10
The total number of of successful reservations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge 0..4294967295  

wfRsvpCurrentSoloistSlot 1.3.6.1.4.1.18.3.5.16.1.1.1.11
The Current RSVP Soloist slot. Slots can be 1-14. Default is zero.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpSessionTable 1.3.6.1.4.1.18.3.5.16.1.1.2
Statistics concerning the sessions seen by a given system.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfRsvpSessionEntry

wfRsvpSessionEntry 1.3.6.1.4.1.18.3.5.16.1.1.2.1
Statistics concerning a single RSVP session seen by a given system.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfRsvpSessionEntry  

wfRsvpSessionDestAddr 1.3.6.1.4.1.18.3.5.16.1.1.2.1.1
The destination address used by all senders in this session. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfRsvpSessionDestAddrLength 1.3.6.1.4.1.18.3.5.16.1.1.2.1.2
The CIDR prefix length of the session address, which is 32 for IP4 host and multicast ad- dresses. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..128  

wfRsvpSessionProtocol 1.3.6.1.4.1.18.3.5.16.1.1.2.1.3
The IP Protocol used by this session. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

wfRsvpSessionPort 1.3.6.1.4.1.18.3.5.16.1.1.2.1.4
The UDP or TCP port number used as a destina- tion port for all senders in this session. If the IP protocol in use, specified by rsvpSen- derProtocol, is 50 (ESP) or 51 (AH), this represents a virtual destination port number. A value of zero indicates that the IP protocol in use does not have ports. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

wfRsvpSessionSenders 1.3.6.1.4.1.18.3.5.16.1.1.2.1.5
The number of senders currently known to be part of this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge 0..4294967295  

wfRsvpSessionReceivers 1.3.6.1.4.1.18.3.5.16.1.1.2.1.6
The number of reservations being requested of this system for this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge 0..4294967295  

wfRsvpSessionRequests 1.3.6.1.4.1.18.3.5.16.1.1.2.1.7
The number of reservation requests this system is sending upstream for this session.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge 0..4294967295  

wfRsvpSenderTable 1.3.6.1.4.1.18.3.5.16.1.1.3
Information describing the state information displayed by senders in PATH messages.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfRsvpSenderEntry

wfRsvpSenderEntry 1.3.6.1.4.1.18.3.5.16.1.1.3.1
Information describing the state information displayed by a single sender's PATH message.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfRsvpSenderEntry  

wfRsvpSenderDestAddr 1.3.6.1.4.1.18.3.5.16.1.1.3.1.1
The destination IP address used by all senders in this session. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfRsvpSenderAddr 1.3.6.1.4.1.18.3.5.16.1.1.3.1.2
The source address used by this sender in this session. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfRsvpSenderDestAddrLength 1.3.6.1.4.1.18.3.5.16.1.1.3.1.3
The length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..128  

wfRsvpSenderAddrLength 1.3.6.1.4.1.18.3.5.16.1.1.3.1.4
The length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..128  

wfRsvpSenderProtocol 1.3.6.1.4.1.18.3.5.16.1.1.3.1.5
The IP Protocol used by this session. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

wfRsvpSenderDestPort 1.3.6.1.4.1.18.3.5.16.1.1.3.1.6
The UDP or TCP port number used as a destina- tion port for all senders in this session. If the IP protocol in use, specified by rsvpSen- derProtocol, is 50 (ESP) or 51 (AH), this represents a virtual destination port number. A value of zero indicates that the IP protocol in use does not have ports. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

wfRsvpSenderPort 1.3.6.1.4.1.18.3.5.16.1.1.3.1.7
The UDP or TCP port number used as a source port for this sender in this session. If the IP protocol in use, specified by rsvpSenderPro- tocol is 50 (ESP) or 51 (AH), this represents a generalized port identifier (GPI). A value of zero indicates that the IP protocol in use does not have ports. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

wfRsvpSenderHopAddr 1.3.6.1.4.1.18.3.5.16.1.1.3.1.8
The address used by the previous RSVP hop (which may be the original sender).
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfRsvpSenderHopLih 1.3.6.1.4.1.18.3.5.16.1.1.3.1.9
The Logical Interface Handle used by the pre- vious RSVP hop (which may be the original sender).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpSenderInterface 1.3.6.1.4.1.18.3.5.16.1.1.3.1.10
The ifIndex value of the interface on which this PATH message was most recently received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpSenderTSpecRate 1.3.6.1.4.1.18.3.5.16.1.1.3.1.11
The Average Bit Rate of the sender's data stream. Within a transmission burst, the ar- rival rate may be as fast as rsvpSenderTSpec- PeakRate (if supported by the service model); however, averaged across two or more burst in- tervals, the rate should not exceed rsvpSen- derTSpecRate. Note that this is a prediction, often based on the general capability of a type of codec or particular encoding; the measured average rate may be significantly lower. UNITS, bits per second
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpSenderTSpecPeakRate 1.3.6.1.4.1.18.3.5.16.1.1.3.1.12
The Peak Bit Rate of the sender's data stream. Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network. If not specified in the TSpec, this returns zero or noSuchValue. UNITS, bits per second
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpSenderTSpecBurst 1.3.6.1.4.1.18.3.5.16.1.1.3.1.13
The size of the largest burst expected from the sender at a time. UNITS, bytes
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpSenderTSpecMinTU 1.3.6.1.4.1.18.3.5.16.1.1.3.1.14
The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpSenderTSpecMaxTU 1.3.6.1.4.1.18.3.5.16.1.1.3.1.15
The maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the interface MTU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpSenderInterval 1.3.6.1.4.1.18.3.5.16.1.1.3.1.16
The interval between refresh messages as ad- vertised by the Previous Hop. UNITS milliseconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpSenderRSVPHop 1.3.6.1.4.1.18.3.5.16.1.1.3.1.17
If TRUE, the node believes that the previous IP hop is an RSVP hop. If FALSE, the node be- lieves that the previous IP hop may not be an RSVP hop.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfRsvpSenderLastChange 1.3.6.1.4.1.18.3.5.16.1.1.3.1.18
The time of the last change in this PATH mes- sage; This is either the first time it was re- ceived or the time of the most recent change in parameters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpSenderPSBTimeout 1.3.6.1.4.1.18.3.5.16.1.1.3.1.19
The remaining lifetime of this sender's PSB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpSenderPolicy 1.3.6.1.4.1.18.3.5.16.1.1.3.1.20
The contents of the policy object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(4..65536)  

wfRsvpSenderAdspecBreak 1.3.6.1.4.1.18.3.5.16.1.1.3.1.21
The global break bit general characterization parameter from the ADSPEC. If TRUE, at least one non-IS hop was detected in the path. If FALSE, no non-IS hops were detected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfRsvpSenderAdspecHopCount 1.3.6.1.4.1.18.3.5.16.1.1.3.1.22
The hop count general characterization parame- ter from the ADSPEC. A return of zero or noSuchValue indicates one of the following con- ditions: the invalid bit was set the parameter was not present
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

wfRsvpSenderAdspecPathBw 1.3.6.1.4.1.18.3.5.16.1.1.3.1.23
The path bandwidth estimate general character- ization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not present UNITS, bits per second
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpSenderAdspecMinLatency 1.3.6.1.4.1.18.3.5.16.1.1.3.1.24
The minimum path latency general characteriza- tion parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not present UNITS, microseconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpSenderAdspecMtu 1.3.6.1.4.1.18.3.5.16.1.1.3.1.25
The composed Maximum Transmission Unit general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present UNITS, bytes
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

wfRsvpSenderAdspecGSSvc 1.3.6.1.4.1.18.3.5.16.1.1.3.1.26
If TRUE, the ADSPEC contains a Guaranteed Ser- vice fragment. If FALSE or noValue, the ADSPEC does not contain a Guaranteed Service fragment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfRsvpSenderAdspecGSBreak 1.3.6.1.4.1.18.3.5.16.1.1.3.1.27
If TRUE, the Guaranteed Service fragment has its 'break' bit set, indicating that one or more nodes along the path do not support the guaranteed service. If FALSE, and rsvpSen- derAdspecGSSvc is TRUE, the 'break' bit is not set. If wfRsvpSenderAdspecGuaranteedSvc is FALSE, this returns FALSE or noSuchValue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), flase(2)  

wfRsvpSenderAdspecGSCtot 1.3.6.1.4.1.18.3.5.16.1.1.3.1.28
If wfRsvpSenderAdspecGSSvc is TRUE, this is the end-to-end composed value for the guaranteed service 'C' parameter. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not present If wfRsvpSenderAdspecGSSvc is FALSE, this returns zero or noSuchValue. UNITS, bytes
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpSenderAdspecGSDtot 1.3.6.1.4.1.18.3.5.16.1.1.3.1.29
If wfRsvpSenderAdspecGSSvc is TRUE, this is the end-to-end composed value for the guaranteed service 'D' parameter. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not present If wfRsvpSenderAdspecGSSvc is FALSE, this returns zero or noSuchValue. UNITS, microseconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpSenderAdspecGSCsum 1.3.6.1.4.1.18.3.5.16.1.1.3.1.30
If wfRsvpSenderAdspecGSSvc is TRUE, this is the composed value for the guaranteed ser- vice 'C' parameter since the last reshaping point. A return of zero or noSuchValue indi- cates one of the following conditions: the invalid bit was set the parameter was not present If wfRsvpSenderAdspecGSSvc is FALSE, this returns zero or noSuchValue. UNITS, bytes
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpSenderAdspecGSDsum 1.3.6.1.4.1.18.3.5.16.1.1.3.1.31
If wfRsvpSenderAdspecGSSvc is TRUE, this is the composed value for the guaranteed ser- vice 'D' parameter since the last reshaping point. A return of zero or noSuchValue indi- cates one of the following conditions: the invalid bit was set the parameter was not present If wfRsvpSenderAdspecGSSvc is FALSE, this returns zero or noSuchValue. UNITS, microseconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpSenderAdspecGSHopCount 1.3.6.1.4.1.18.3.5.16.1.1.3.1.32
If wfRsvpSenderAdspecGSSvc is TRUE, this is the service-specific override of the hop count general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If wfRsvpSenderAdspecGSSvc is FALSE, this returns zero or noSuchValue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

wfRsvpSenderAdspecGSPathBw 1.3.6.1.4.1.18.3.5.16.1.1.3.1.33
If wfRsvpSenderAdspecGSSvc is TRUE, this is the service-specific override of the path bandwidth estimate general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following con- ditions: the invalid bit was set the parameter was not present If wfRsvpSenderAdspecGSSvc is FALSE, this returns zero or noSuchValue. UNITS, bits per second
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpSenderAdspecGSMinLatency 1.3.6.1.4.1.18.3.5.16.1.1.3.1.34
If wfRsvpSenderAdspecGSSvc is TRUE, this is the service-specific override of the minimum path latency general characterization parameter from the ADSPEC. A return of zero or noSuch- Value indicates one of the following condi- tions: the invalid bit was set the parameter was not present If wfRsvpSenderAdspecGSSvc is FALSE, this returns zero or noSuchValue. UNITS, microseconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpSenderAdspecGSMtu 1.3.6.1.4.1.18.3.5.16.1.1.3.1.35
If wfRsvpSenderAdspecGSSvc is TRUE, this is the service-specific override of the com- posed Maximum Transmission Unit general charac- terization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If wfRsvpSenderAdspecGSSvc is FALSE, this returns zero or noSuchValue. UNITS, bytes
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

wfRsvpSenderAdspecCLSvc 1.3.6.1.4.1.18.3.5.16.1.1.3.1.36
If TRUE, the ADSPEC contains a Controlled Load Service fragment. If FALSE, the ADSPEC does not contain a Controlled Load Service frag- ment.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfRsvpSenderAdspecCLBreak 1.3.6.1.4.1.18.3.5.16.1.1.3.1.37
If TRUE, the Controlled Load Service fragment has its 'break' bit set, indicating that one or more nodes along the path do not support the controlled load service. If FALSE, and wfRsvpSenderAdspecCLSvc is TRUE, the 'break' bit is not set. If wfRsvpSenderAdspecCLSvc is FALSE, this returns FALSE or noSuchValue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfRsvpSenderAdspecCLHopCount 1.3.6.1.4.1.18.3.5.16.1.1.3.1.38
If wfRsvpSenderAdspecCLSvc is TRUE, this is the service-specific override of the hop count general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If wfRsvpSenderAdspecCLSvc is FALSE, this returns zero or noSuchValue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

wfRsvpSenderAdspecCLPathBw 1.3.6.1.4.1.18.3.5.16.1.1.3.1.39
If wfRsvpSenderAdspecCLSvc is TRUE, this is the service-specific override of the path bandwidth estimate general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following con- ditions: the invalid bit was set the parameter was not present If wfRsvpSenderAdspecCLSvc is FALSE, this returns zero or noSuchValue. UNITS, bits per second
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpSenderAdspecCLMinLatency 1.3.6.1.4.1.18.3.5.16.1.1.3.1.40
If wfRsvpSenderAdspecCLSvc is TRUE, this is the service-specific override of the minimum path latency general characterization parameter from the ADSPEC. A return of zero or noSuch- Value indicates one of the following condi- tions: the invalid bit was set the parameter was not present If wfRsvpSenderAdspecCLSvc is FALSE, this returns zero or noSuchValue. UNITS, microseconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpSenderAdspecCLMtu 1.3.6.1.4.1.18.3.5.16.1.1.3.1.41
If wfRsvpSenderAdspecCLSvc is TRUE, this is the service-specific override of the com- posed Maximum Transmission Unit general charac- terization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If wfRsvpSenderAdspecCLSvc is FALSE, this returns zero or noSuchValue. UNITS, bytes
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

wfRsvpSenderStatus 1.3.6.1.4.1.18.3.5.16.1.1.3.1.42
'valid' for all active PATH messages.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

wfRsvpResvTable 1.3.6.1.4.1.18.3.5.16.1.1.4
Information describing the state information displayed by receivers in RESV messages.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfRsvpResvEntry

wfRsvpResvEntry 1.3.6.1.4.1.18.3.5.16.1.1.4.1
Information describing the state information displayed by a single receiver's RESV message concerning a single sender.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfRsvpResvEntry  

wfRsvpResvDestAddr 1.3.6.1.4.1.18.3.5.16.1.1.4.1.1
The destination address used by all senders in this session. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfRsvpResvSenderAddr 1.3.6.1.4.1.18.3.5.16.1.1.4.1.2
The source address of the sender selected by this reservation. The value of all zeroes in- dicates 'all senders'. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfRsvpResvDestAddrLength 1.3.6.1.4.1.18.3.5.16.1.1.4.1.3
The length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..128  

wfRsvpResvSenderAddrLength 1.3.6.1.4.1.18.3.5.16.1.1.4.1.4
The length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..128  

wfRsvpResvProtocol 1.3.6.1.4.1.18.3.5.16.1.1.4.1.5
The IP Protocol used by this session. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

wfRsvpResvDestPort 1.3.6.1.4.1.18.3.5.16.1.1.4.1.6
The UDP or TCP port number used as a destina- tion port for all senders in this session. If the IP protocol in use, specified by wfRsvpResvProtocol, is 50 (ESP) or 51 (AH), this represents a virtual destination port number. A value of zero indicates that the IP protocol in use does not have ports. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

wfRsvpResvPort 1.3.6.1.4.1.18.3.5.16.1.1.4.1.7
The UDP or TCP port number used as a source port for this sender in this session. If the IP protocol in use, specified by wfRsvpResvProto- col is 50 (ESP) or 51 (AH), this represents a generalized port identifier (GPI). A value of zero indicates that the IP protocol in use does not have ports. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

wfRsvpResvHopAddr 1.3.6.1.4.1.18.3.5.16.1.1.4.1.8
The address used by the next RSVP hop (which may be the ultimate receiver).
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfRsvpResvHopLih 1.3.6.1.4.1.18.3.5.16.1.1.4.1.9
The Logical Interface Handle received from the previous RSVP hop (which may be the ultimate receiver).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpResvInterface 1.3.6.1.4.1.18.3.5.16.1.1.4.1.10
The ifIndex value of the interface on which this RESV message was most recently received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpResvService 1.3.6.1.4.1.18.3.5.16.1.1.4.1.11
The QoS Service classification requested by the receiver.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER controlledDelay(1), guaranteedDelay(2), predictive(3), controlledLoad(5)  

wfRsvpResvTSpecRate 1.3.6.1.4.1.18.3.5.16.1.1.4.1.12
The Average Bit Rate of the sender's data stream. Within a transmission burst, the ar- rival rate may be as fast as wfRsvpResvTSpec- PeakRate (if supported by the service model); however, averaged across two or more burst in- tervals, the rate should not exceed wfRsvpResvTSpecRate. Note that this is a prediction, often based on the general capability of a type of codec or particular encoding; the measured average rate may be significantly lower. UNITS, bits per second
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpResvTSpecPeakRate 1.3.6.1.4.1.18.3.5.16.1.1.4.1.13
The Peak Bit Rate of the sender's data stream. Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network. If not specified in the TSpec, this returns zero or noSuchValue. UNITS, bits per second
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpResvTSpecBurst 1.3.6.1.4.1.18.3.5.16.1.1.4.1.14
The size of the largest burst expected from the sender at a time. If this is less than the sender's advertised burst size, the receiver is asking the network to provide flow pacing beyond what would be provided under normal circumstances. Such pac- ing is at the network's option. UNITS, bytes
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpResvTSpecMinTU 1.3.6.1.4.1.18.3.5.16.1.1.4.1.15
The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpResvTSpecMaxTU 1.3.6.1.4.1.18.3.5.16.1.1.4.1.16
The maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the interface MTU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpResvTSpecLevel 1.3.6.1.4.1.18.3.5.16.1.1.4.1.17
If the service is predictive or controlled- delay, this is the service level that is being requested. Otherwise, it is zero, or the agent may return noSuchValue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..3  

wfRsvpResvRSpecRate 1.3.6.1.4.1.18.3.5.16.1.1.4.1.18
If the requested service is Guaranteed, as specified by wfRsvpResvService, this is the clearing rate that is being requested. Other- wise, it is zero, or the agent may return noSuchValue. UNITS, bits per second
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpResvRSpecSlack 1.3.6.1.4.1.18.3.5.16.1.1.4.1.19
If the requested service is Guaranteed, as specified by wfRsvpResvService, this is the delay slack. Otherwise, it is zero, or the agent may return noSuchValue.UNITS, microseconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpResvInterval 1.3.6.1.4.1.18.3.5.16.1.1.4.1.20
The interval between refresh messages as ad- vertised by the Next Hop. UNITS milliseconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpResvScope 1.3.6.1.4.1.18.3.5.16.1.1.4.1.21
The contents of the scope object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length. If the length is non-zero, this contains a series of IP4 or IP6 addresses.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..65536)  

wfRsvpResvShared 1.3.6.1.4.1.18.3.5.16.1.1.4.1.22
If TRUE, a reservation shared among senders is requested. If FALSE, a reservation specific to this sender is requested.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfRsvpResvExplicit 1.3.6.1.4.1.18.3.5.16.1.1.4.1.23
If TRUE, individual senders are listed using Filter Specifications. If FALSE, all senders are implicitly selected. The Scope Object will contain a list of senders that need to receive this reservation request for the purpose of routing the RESV message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfRsvpResvRSVPHop 1.3.6.1.4.1.18.3.5.16.1.1.4.1.24
If TRUE, the node believes that the previous IP hop is an RSVP hop. If FALSE, the node be- lieves that the previous IP hop may not be an RSVP hop.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfRsvpResvLastChange 1.3.6.1.4.1.18.3.5.16.1.1.4.1.25
The time of the last change in this reserva- tion request; This is either the first time it was received or the time of the most recent change in parameters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpResvRSBTimeout 1.3.6.1.4.1.18.3.5.16.1.1.4.1.26
The remaining lifetime of this reservation's RSB.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpResvPolicy 1.3.6.1.4.1.18.3.5.16.1.1.4.1.27
The contents of the policy object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..65536)  

wfRsvpResvStatus 1.3.6.1.4.1.18.3.5.16.1.1.4.1.28
'valid' for all active RESV messages.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

wfRsvpResvFwdTable 1.3.6.1.4.1.18.3.5.16.1.1.5
Information describing the state information displayed upstream in RESV messages.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfRsvpResvFwdEntry

wfRsvpResvFwdEntry 1.3.6.1.4.1.18.3.5.16.1.1.5.1
Information describing the state information displayed upstream in an RESV message concern- ing a single sender.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfRsvpResvFwdEntry  

wfRsvpResvFwdDestAddr 1.3.6.1.4.1.18.3.5.16.1.1.5.1.1
The destination address used by all senders in this session. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfRsvpResvFwdSenderAddr 1.3.6.1.4.1.18.3.5.16.1.1.5.1.2
The source address of the sender selected by this reservation. The value of all zeroes in- dicates 'all senders'. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfRsvpResvFwdDestAddrLength 1.3.6.1.4.1.18.3.5.16.1.1.5.1.3
The length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..128  

wfRsvpResvFwdSenderAddrLength 1.3.6.1.4.1.18.3.5.16.1.1.5.1.4
The length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..128  

wfRsvpResvFwdProtocol 1.3.6.1.4.1.18.3.5.16.1.1.5.1.5
The IP Protocol used by this session. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..255  

wfRsvpResvFwdDestPort 1.3.6.1.4.1.18.3.5.16.1.1.5.1.6
The UDP or TCP port number used as a destina- tion port for all senders in this session. If the IP protocol in use, specified by wfRsvpResvFwdProtocol, is 50 (ESP) or 51 (AH), this represents a virtual destination port number. A value of zero indicates that the IP protocol in use does not have ports. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

wfRsvpResvFwdPort 1.3.6.1.4.1.18.3.5.16.1.1.5.1.7
The UDP or TCP port number used as a source port for this sender in this session. If the IP protocol in use, specified by wfRsvpResvFwdProto- col is 50 (ESP) or 51 (AH), this represents a generalized port identifier (GPI). A value of zero indicates that the IP protocol in use does not have ports. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

wfRsvpResvFwdHopAddr 1.3.6.1.4.1.18.3.5.16.1.1.5.1.8
The address used by the next RSVP hop (which may be the ultimate receiver).
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfRsvpResvFwdHopLih 1.3.6.1.4.1.18.3.5.16.1.1.5.1.9
The Logical Interface Handle received from the previous RSVP hop (which may be the ultimate receiver).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpResvFwdInterface 1.3.6.1.4.1.18.3.5.16.1.1.5.1.10
The ifIndex value of the interface on which this RESV message was most recently received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpResvFwdService 1.3.6.1.4.1.18.3.5.16.1.1.5.1.11
The QoS Service classification requested by the receiver.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER controlledDelay(1), guaranteedDelay(2), predictive(3), controlledLoad(5)  

wfRsvpResvFwdTSpecRate 1.3.6.1.4.1.18.3.5.16.1.1.5.1.12
The Average Bit Rate of the sender's data stream. Within a transmission burst, the ar- rival rate may be as fast as wfRsvpResvFwdTSpec- PeakRate (if supported by the service model); however, averaged across two or more burst in- tervals, the rate should not exceed wfRsvpResvFwdTSpecRate. Note that this is a prediction, often based on the general capability of a type of codec or particular encoding; the measured average rate may be significantly lower. UNITS, bits per second
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpResvFwdTSpecPeakRate 1.3.6.1.4.1.18.3.5.16.1.1.5.1.13
The Peak Bit Rate of the sender's data stream. Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network. If not specified in the TSpec, this returns zero or noSuchValue. UNITS, bits per second
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpResvFwdTSpecBurst 1.3.6.1.4.1.18.3.5.16.1.1.5.1.14
The size of the largest burst expected from the sender at a time. If this is less than the sender's advertised burst size, the receiver is asking the network to provide flow pacing beyond what would be provided under normal circumstances. Such pac- ing is at the network's option. UNITS, bytes
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpResvFwdTSpecMinTU 1.3.6.1.4.1.18.3.5.16.1.1.5.1.15
The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpResvFwdTSpecMaxTU 1.3.6.1.4.1.18.3.5.16.1.1.5.1.16
The maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the interface MTU.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpResvFwdTSpecLevel 1.3.6.1.4.1.18.3.5.16.1.1.5.1.17
If the service is predictive or controlled- delay, this is the service level that is being requested. Otherwise, it is zero, or the agent may return noSuchValue.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..3  

wfRsvpResvFwdRSpecRate 1.3.6.1.4.1.18.3.5.16.1.1.5.1.18
If the requested service is Guaranteed, as specified by wfRsvpResvFwdService, this is the clearing rate that is being requested. Other- wise, it is zero, or the agent may return noSuchValue. UNITS, bits per second
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpResvFwdRSpecSlack 1.3.6.1.4.1.18.3.5.16.1.1.5.1.19
If the requested service is Guaranteed, as specified by wfRsvpResvFwdService, this is the delay slack. Otherwise, it is zero, or the agent may return noSuchValue.UNITS, microseconds
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpResvFwdInterval 1.3.6.1.4.1.18.3.5.16.1.1.5.1.20
The interval between refresh messages as ad- vertised by the Next Hop.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfRsvpResvFwdScope 1.3.6.1.4.1.18.3.5.16.1.1.5.1.21
The contents of the scope object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length. If the length is non-zero, this contains a series of IP4 or IP6 addresses.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..65536)  

wfRsvpResvFwdShared 1.3.6.1.4.1.18.3.5.16.1.1.5.1.22
If TRUE, a reservation shared among senders is requested. If FALSE, a reservation specific to this sender is requested.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfRsvpResvFwdExplicit 1.3.6.1.4.1.18.3.5.16.1.1.5.1.23
If TRUE, individual senders are listed using Filter Specifications. If FALSE, all senders are implicitly selected. The Scope Object will contain a list of senders that need to receive this reservation request for the purpose of routing the RESV message.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfRsvpResvFwdRSVPHop 1.3.6.1.4.1.18.3.5.16.1.1.5.1.24
If TRUE, the node believes that the previous IP hop is an RSVP hop. If FALSE, the node be- lieves that the previous IP hop may not be an RSVP hop.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfRsvpResvFwdLastChange 1.3.6.1.4.1.18.3.5.16.1.1.5.1.25
The time of the last change in this reserva- tion request; This is either the first time it was received or the time of the most recent change in parameters.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpResvFwdPolicy 1.3.6.1.4.1.18.3.5.16.1.1.5.1.26
The contents of the policy object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..65536)  

wfRsvpResvFwdStatus 1.3.6.1.4.1.18.3.5.16.1.1.5.1.27
'valid' for all active RESV messages. This object may be used to install static RESV in- formation or delete RESV information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

wfRsvpIfTable 1.3.6.1.4.1.18.3.5.16.1.1.6
List of configured RSVP interface.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfRsvpIfEntry

wfRsvpIfEntry 1.3.6.1.4.1.18.3.5.16.1.1.6.1
A description of an RSVP interface
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfRsvpIfEntry  

wfRsvpIfDelete 1.3.6.1.4.1.18.3.5.16.1.1.6.1.1
Indicates whether this RSVP If record is to be deleted or created
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfRsvpIfEnable 1.3.6.1.4.1.18.3.5.16.1.1.6.1.2
Indicates whether this RSVP intf record is to be enabled or disabled
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfRsvpIfState 1.3.6.1.4.1.18.3.5.16.1.1.6.1.3
The current state of the RSVP interface. Invalid indicates an error in processing the cfg record
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpres(4)  

wfRsvpIfCct 1.3.6.1.4.1.18.3.5.16.1.1.6.1.4
The circuit number of this RSVP interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpIfUdpNbrs 1.3.6.1.4.1.18.3.5.16.1.1.6.1.5
The number of neighbors perceived to be using only the RSVP UDP Encapsulation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge 0..4294967295  

wfRsvpIfIpNbrs 1.3.6.1.4.1.18.3.5.16.1.1.6.1.6
The number of neighbors perceived to be using only the RSVP IP Encapsulation.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge 0..4294967295  

wfRsvpIfNbrs 1.3.6.1.4.1.18.3.5.16.1.1.6.1.7
The number of neighbors currently perceived; this will exceed wfRsvpIfIpNbrs + wfRsvpIfUdpNbrs by the number of neighbors using both encapsulations.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge 0..4294967295  

wfRsvpIfRefreshBlockadeMultiple 1.3.6.1.4.1.18.3.5.16.1.1.6.1.8
The value of the RSVP value 'Kb', Which is the minimum number of refresh intervals that blockade state will last once entered.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..65536  

wfRsvpIfRefreshMultiple 1.3.6.1.4.1.18.3.5.16.1.1.6.1.9
The value of the RSVP value 'K', which is the number of refresh intervals which must elapse (minimum) before a PATH or RESV message which is not being refreshed will be aged out.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..65536  

wfRsvpIfTTL 1.3.6.1.4.1.18.3.5.16.1.1.6.1.10
The value of SEND_TTL used on this interface for messages this node originates. If set to zero, the node determines the TTL via other means.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

wfRsvpIfRefreshInterval 1.3.6.1.4.1.18.3.5.16.1.1.6.1.11
The value of the RSVP value 'R', which is the minimum period between refresh transmissions of a given PATH or RESV message on an interface. UNITS milliseconds
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 2000..2147483647  

wfRsvpIfRouteDelay 1.3.6.1.4.1.18.3.5.16.1.1.6.1.12
The approximate period from the time a route is changed to the time a resulting message ap- pears on the interface. UNITS hundredths of a second
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfRsvpIfUdpRequired 1.3.6.1.4.1.18.3.5.16.1.1.6.1.13
If TRUE, manual configuration forcees the use of UDP ncapsulation on the interface. If FALSE, UDP encapsulation is only used if wfrsvpIfUdpNbrs is not zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfRsvpNbrTable 1.3.6.1.4.1.18.3.5.16.1.1.7
Information describing the Neighbors of an RSVP system.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfRsvpNbrEntry

wfRsvpNbrEntry 1.3.6.1.4.1.18.3.5.16.1.1.7.1
Information describing a single RSVP Neigh- bor.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfRsvpNbrEntry  

wfRsvpNbrAddress 1.3.6.1.4.1.18.3.5.16.1.1.7.1.1
The IP4 or IP6 Address used by this neighbor. This object may not be changed when the value of the RowStatus object is 'valid'.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfRsvpNbrProtocol 1.3.6.1.4.1.18.3.5.16.1.1.7.1.2
The encapsulation being used by this neigh- bor.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER ip(1), udp(2), both(3)  

wfRsvpNbrCct 1.3.6.1.4.1.18.3.5.16.1.1.7.1.3
The circuit number of the interface where the neighbor is learned
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfRsvpNbrStatus 1.3.6.1.4.1.18.3.5.16.1.1.7.1.4
'valid' for all neighbors. This object may be used to configure neighbors. In the presence of configured neighbors, the implementation may (but is not required to) limit the set of valid neighbors to those configured.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2)  

wfSRsvp 1.3.6.1.4.1.18.3.5.16.1.1.8
OBJECT IDENTIFIER    

wfSRsvpDelete 1.3.6.1.4.1.18.3.5.16.1.1.8.1
Create/Delete parameter. Default is created. Users perform a set operation on this object in order to create/delete Static Rsvp.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfSRsvpDisable 1.3.6.1.4.1.18.3.5.16.1.1.8.2
Enable/Disable parameter. Default is enabled. Users perform a set operation on this object in order to enable/disable Static Rsvp.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSRsvpState 1.3.6.1.4.1.18.3.5.16.1.1.8.3
The current state of Static Rsvp.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpres(4)  

wfSRsvpSoloistSlot 1.3.6.1.4.1.18.3.5.16.1.1.8.4
Slot for which slot Static RSVP Soloist is eligible to run on. Slots can be 1-14.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..14  

wfSRsvpInfoLogFilter 1.3.6.1.4.1.18.3.5.16.1.1.8.5
Turn Static RSVP log ON or OFF for informational and warning messages. There is only RSVP_LOG_RIF_PROCESSING 0x0001 - RIF processing. RSVP_LOG_SOLO_PROCESSING 0x0002 - SOLO processing. RSVP_LOG_ROUTE_INTF_PROCESSING 0x0004 - ROUTE interface processing. RSVP_LOG_MERGE_PROCESSING 0x0008 - MERGE processing. RSVP_LOG_DB_PROCESSING 0x0010 - database access processing. RSVP_LOG_INTSERV_INTF_PROCESSING 0x0020 - INTSERV interface processing. RSVP_LOG_CRM_INTF_PROCESSING 0x0040 - CRM interface processing. RSVP_LOG_STATIC_RSVP 0x0080 - STATIC RSVP processing. RSVP_LOG_CONTROL_PROCESSING 0x0100 - CONTROL processing. RSVP_LOG_MAP_VEC_PROCESSING 0x0200 - MAP VECTOR processing. RSVP_LOG_PROXY_PROCESSING 0x0400 - RSVP MIB PROXY processing. RSVP_LOG_REFRESH_PROCESSING 0x0800 - Path/Resv Refresh processing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSRsvpDebugLogFilter 1.3.6.1.4.1.18.3.5.16.1.1.8.6
Turn Static RSVP log ON or OFF for debugging messages. The bit position is used to represent a RSVP module: RSVP_LOG_RIF_PROCESSING 0x0001 - RIF processing. RSVP_LOG_SOLO_PROCESSING 0x0002 - SOLO processing. RSVP_LOG_ROUTE_INTF_PROCESSING 0x0004 - ROUTE interface processing. RSVP_LOG_MERGE_PROCESSING 0x0008 - MERGE processing. RSVP_LOG_DB_PROCESSING 0x0010 - database access processing. RSVP_LOG_INTSERV_INTF_PROCESSING 0x0020 - INTSERV interface processing. RSVP_LOG_CRM_INTF_PROCESSING 0x0040 - CRM interface processing. RSVP_LOG_STATIC_RSVP 0x0080 - STATIC RSVP processing. RSVP_LOG_CONTROL_PROCESSING 0x0100 - CONTROL processing. RSVP_LOG_MAP_VEC_PROCESSING 0x0200 - MAP VECTOR processing. RSVP_LOG_PROXY_PROCESSING 0x0400 - RSVP MIB PROXY processing. RSVP_LOG_REFRESH_PROCESSING 0x0800 - Path/Resv Refresh processing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSRsvpTraceLogFilter 1.3.6.1.4.1.18.3.5.16.1.1.8.7
Turn RSVP log ON or OFF for RSVP trace messages. The bit position is used to represent a RSVP module: RSVP_LOG_RIF_PROCESSING 0x0001 - RIF processing. RSVP_LOG_SOLO_PROCESSING 0x0002 - SOLO processing. RSVP_LOG_ROUTE_INTF_PROCESSING 0x0004 - ROUTE interface processing. RSVP_LOG_MERGE_PROCESSING 0x0008 - MERGE processing. RSVP_LOG_DB_PROCESSING 0x0010 - database access processing. RSVP_LOG_INTSERV_INTF_PROCESSING 0x0020 - INTSERV interface processing. RSVP_LOG_CRM_INTF_PROCESSING 0x0040 - CRM interface processing. RSVP_LOG_STATIC_RSVP 0x0080 - STATIC RSVP processing. RSVP_LOG_CONTROL_PROCESSING 0x0100 - CONTROL processing. RSVP_LOG_MAP_VEC_PROCESSING 0x0200 - MAP VECTOR processing. RSVP_LOG_PROXY_PROCESSING 0x0400 - RSVP MIB PROXY processing. RSVP_LOG_REFRESH_PROCESSING 0x0800 - Path/Resv Refresh processing.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSRsvpRefreshInterval 1.3.6.1.4.1.18.3.5.16.1.1.8.8
The value of the RSVP value 'R', which is the minimum period between refresh transmissions of a given STATIC PATH or STATIC RESV message. UNITS milliseconds
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 2000..2147483647  

wfSRsvpTotalSenders 1.3.6.1.4.1.18.3.5.16.1.1.8.9
The total number of Static Sender (PATH) states in the router.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge 0..4294967295  

wfSRsvpTotalReservations 1.3.6.1.4.1.18.3.5.16.1.1.8.10
The total number of Static Reservation (RESV) states in the router.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge 0..4294967295  

wfSRsvpSenderTable 1.3.6.1.4.1.18.3.5.16.1.1.9
Information describing the state information displayed by senders statically configured.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfSRsvpSenderEntry

wfSRsvpSenderEntry 1.3.6.1.4.1.18.3.5.16.1.1.9.1
Information describing the state information used to create a sender thru configuration.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfSRsvpSenderEntry  

wfSRsvpSenderCreate 1.3.6.1.4.1.18.3.5.16.1.1.9.1.1
Whether to Delete this sender PSB
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER create(1), delete(2)  

wfSRsvpSenderEnable 1.3.6.1.4.1.18.3.5.16.1.1.9.1.2
Whether to Disable this Sender PSB
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSRsvpSenderStatus 1.3.6.1.4.1.18.3.5.16.1.1.9.1.3
Whether this Static PSB is valid or not
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2), notpres(3)  

wfSRsvpSenderNumber 1.3.6.1.4.1.18.3.5.16.1.1.9.1.4
The number of this static sender. This is for SNMP Indexing purposes only and has no relation to any protocol value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSRsvpSenderDestReplicate 1.3.6.1.4.1.18.3.5.16.1.1.9.1.5
Number of sessions for which this static path state should be replicated. For each replication, wfSRsvpSenderDestAddr will be incremented by one.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSRsvpSenderReplicate 1.3.6.1.4.1.18.3.5.16.1.1.9.1.6
Number of senders for which this static path state should be replicated. For each replication, wfSRsvpSenderAddr will be incremented by one.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSRsvpSenderIntegrity 1.3.6.1.4.1.18.3.5.16.1.1.9.1.7
The contents of the integrity object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..65536)  

wfSRsvpSenderDestAddr 1.3.6.1.4.1.18.3.5.16.1.1.9.1.8
The destination IP address used by all senders in this session. This object may not be changed when the value of the Status object is 'valid'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfSRsvpSenderAddr 1.3.6.1.4.1.18.3.5.16.1.1.9.1.9
The source address used by this sender in this session. This object may not be changed when the value of the Status object is 'valid'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfSRsvpSenderDestAddrLength 1.3.6.1.4.1.18.3.5.16.1.1.9.1.10
The length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be changed when the value of the Status object is 'valid'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..128  

wfSRsvpSenderAddrLength 1.3.6.1.4.1.18.3.5.16.1.1.9.1.11
The length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be changed when the value of the Status object is 'valid'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..128  

wfSRsvpSenderProtocol 1.3.6.1.4.1.18.3.5.16.1.1.9.1.12
The IP Protocol used by this session. This object may not be changed when the value of the Status object is 'valid'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

wfSRsvpSenderDestPort 1.3.6.1.4.1.18.3.5.16.1.1.9.1.13
The UDP or TCP port number used as a destina- tion port for all senders in this session. If the IP protocol in use, specified by rsvpSen- derProtocol, is 50 (ESP) or 51 (AH), this represents a virtual destination port number. A value of zero indicates that the IP protocol in use does not have ports. This object may not be changed when the value of the Status object is 'valid'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65536  

wfSRsvpSenderPort 1.3.6.1.4.1.18.3.5.16.1.1.9.1.14
The UDP or TCP port number used as a source port for this sender in this session. If the IP protocol in use, specified by RsvpStaticSenderPro- tocol is 50 (ESP) or 51 (AH), this represents a generalized port identifier (GPI). A value of zero indicates that the IP protocol in use does not have ports. This object may not be changed when the value of the Status object is 'valid'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65536  

wfSRsvpSenderHopAddr 1.3.6.1.4.1.18.3.5.16.1.1.9.1.15
The address used by the previous RSVP hop (which may be the original sender).
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfSRsvpSenderHopLih 1.3.6.1.4.1.18.3.5.16.1.1.9.1.16
The Logical Interface Handle used by the pre- vious RSVP hop (which may be the original sender).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSRsvpSenderInterface 1.3.6.1.4.1.18.3.5.16.1.1.9.1.17
The ifIndex value of the interface on which this PATH message was most recently received.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSRsvpSenderTimeValue 1.3.6.1.4.1.18.3.5.16.1.1.9.1.18
The value of the RSVP value 'R', which is the minimum period between refresh transmissions of a given PATH or RESV message on an interface. UNITS milliseconds
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderTSpecRate 1.3.6.1.4.1.18.3.5.16.1.1.9.1.19
The Average Bit Rate of the sender's data stream. Within a transmission burst, the ar- rival rate may be as fast as RsvpStaticSenderTSpec- PeakRate (if supported by the service model); however, averaged across two or more burst in- tervals, the rate should not exceed rsvpSen- derTSpecRate. Note that this is a prediction, often based on the general capability of a type of codec or particular encoding; the measured average rate may be significantly lower. UNITS, bits per second
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderTSpecPeakRate 1.3.6.1.4.1.18.3.5.16.1.1.9.1.20
The Peak Bit Rate of the sender's data stream. Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network. If not specified in the TSpec, this returns zero or noSuchValue. UNITS, bits per second
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderTSpecBurst 1.3.6.1.4.1.18.3.5.16.1.1.9.1.21
The size of the largest burst expected from the sender at a time. UNITS, bytes
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderTSpecMinTU 1.3.6.1.4.1.18.3.5.16.1.1.9.1.22
The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderTSpecMaxTU 1.3.6.1.4.1.18.3.5.16.1.1.9.1.23
The maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the interface MTU.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderPolicy 1.3.6.1.4.1.18.3.5.16.1.1.9.1.24
The contents of the policy object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..65536)  

wfSRsvpSenderAdspec 1.3.6.1.4.1.18.3.5.16.1.1.9.1.25
If TRUE, an adspec is sent, if FALSE, no adspec is sent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfSRsvpSenderAdspecBreak 1.3.6.1.4.1.18.3.5.16.1.1.9.1.26
The global break bit general characterization parameter from the ADSPEC. If TRUE, at least one non-IS hop was detected in the path. If FALSE, no non-IS hops were detected.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfSRsvpSenderAdspecHopCount 1.3.6.1.4.1.18.3.5.16.1.1.9.1.27
The hop count general characterization parame- ter from the ADSPEC. A return of zero or noSuchValue indicates one of the following con- ditions: the invalid bit was set the parameter was not present
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderAdspecPathBw 1.3.6.1.4.1.18.3.5.16.1.1.9.1.28
The path bandwidth estimate general character- ization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not present UNITS, bits per second
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderAdspecMinLatency 1.3.6.1.4.1.18.3.5.16.1.1.9.1.29
The minimum path latency general characteriza- tion parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not present UNITS, microseconds
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderAdspecMtu 1.3.6.1.4.1.18.3.5.16.1.1.9.1.30
The composed Maximum Transmission Unit general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present UNITS, bytes
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderAdspecGSSvc 1.3.6.1.4.1.18.3.5.16.1.1.9.1.31
If TRUE, the ADSPEC contains a Guaranteed Ser- vice fragment. If FALSE, the ADSPEC does not contain a Guaranteed Service fragment.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfSRsvpSenderAdspecGSBreak 1.3.6.1.4.1.18.3.5.16.1.1.9.1.32
If TRUE, the Guaranteed Service fragment has its 'break' bit set, indicating that one or more nodes along the path do not support the guaranteed service. If FALSE, and wfSRrsvpSenderAdspecGSSvc is TRUE, the 'break' bit is not set. If wfSRsvpSenderAdspecGSSvc is FALSE, this returns FALSE or noSuchValue.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfSRsvpSenderAdspecGSCtot 1.3.6.1.4.1.18.3.5.16.1.1.9.1.33
If wfSRsvpSenderAdspecGSSvc is TRUE, this is the end-to-end composed value for the guaranteed service 'C' parameter. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not present If wfSRsvpSenderAdspecGSSvc is FALSE, this returns zero or noSuchValue. UNITS, bytes
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderAdspecGSDtot 1.3.6.1.4.1.18.3.5.16.1.1.9.1.34
If wfSRsvpSenderAdspecGSSvc is TRUE, this is the end-to-end composed value for the guaranteed service 'D' parameter. A return of zero or noSuchValue indicates one of the fol- lowing conditions: the invalid bit was set the parameter was not present If wfSRsvpSenderAdspecGSSvc is FALSE, this returns zero or noSuchValue. UNITS, microseconds
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderAdspecGSCsum 1.3.6.1.4.1.18.3.5.16.1.1.9.1.35
If wfSRsvpSenderAdspecGSSvc is TRUE, this is the composed value for the guaranteed ser- vice 'C' parameter since the last reshaping point. A return of zero or noSuchValue indi- cates one of the following conditions: the invalid bit was set the parameter was not present If wfSRsvpSenderAdspecGSSvc is FALSE, this returns zero or noSuchValue. UNITS, bytes
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderAdspecGSDsum 1.3.6.1.4.1.18.3.5.16.1.1.9.1.36
If wfSRsvpSenderAdspecGSSvc is TRUE, this is the composed value for the guaranteed ser- vice 'D' parameter since the last reshaping point. A return of zero or noSuchValue indi- cates one of the following conditions: the invalid bit was set the parameter was not present If wfSRsvpSenderAdspecGSSvc is FALSE, this returns zero or noSuchValue. UNITS, microseconds
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderAdspecGSOverrides 1.3.6.1.4.1.18.3.5.16.1.1.9.1.37
If TRUE, the ADSPEC contains general parameter overrides for guaranteed service. If FALSE, the ADSPEC does not contains guaranteed service overrides. Note, if TRUE, ALL override parameters will be included and must be specified.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfSRsvpSenderAdspecGSHopCount 1.3.6.1.4.1.18.3.5.16.1.1.9.1.38
If wfSRsvpSenderAdspecGSSvc is TRUE, this is the service-specific override of the hop count general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If wfSRsvpSenderAdspecGSSvc is FALSE, this returns zero or noSuchValue.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderAdspecGSPathBw 1.3.6.1.4.1.18.3.5.16.1.1.9.1.39
If wfSRsvpSenderAdspecGSSvc is TRUE, this is the service-specific override of the path bandwidth estimate general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following con- ditions: the invalid bit was set the parameter was not present If wfSRsvpSenderAdspecGSSvc is FALSE, this returns zero or noSuchValue. UNITS, bits per second
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderAdspecGSMinLatency 1.3.6.1.4.1.18.3.5.16.1.1.9.1.40
If wfSRsvpSenderAdspecGSSvc is TRUE, this is the service-specific override of the minimum path latency general characterization parameter from the ADSPEC. A return of zero or noSuch- Value indicates one of the following condi- tions: the invalid bit was set the parameter was not present If wfSRsvpSenderAdspecGSSvc is FALSE, this returns zero or noSuchValue. UNITS, microseconds
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderAdspecGSMtu 1.3.6.1.4.1.18.3.5.16.1.1.9.1.41
If wfSRsvpSenderAdspecGSSvc is TRUE, this is the service-specific override of the com- posed Maximum Transmission Unit general charac- terization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If wfSRsvpSenderAdspecGSSvc is FALSE, this returns zero or noSuchValue. UNITS, bytes
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderAdspecCLSvc 1.3.6.1.4.1.18.3.5.16.1.1.9.1.42
If TRUE, the ADSPEC contains a Controlled Load Service fragment. If FALSE, the ADSPEC does not contain a Controlled Load Service frag- ment.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfSRsvpSenderAdspecCLBreak 1.3.6.1.4.1.18.3.5.16.1.1.9.1.43
If TRUE, the Controlled Load Service fragment has its 'break' bit set, indicating that one or more nodes along the path do not support the controlled load service. If FALSE, and wfSRsvpSenderAdspecCLSvc is TRUE, the 'break' bit is not set. If wfSRsvpSenderAdspecCLSvc is FALSE, this returns FALSE or noSuchValue.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfSRsvpSenderAdspecCLOverrides 1.3.6.1.4.1.18.3.5.16.1.1.9.1.44
If TRUE, the ADSPEC contains general parameter overrides for controlled load service. If FALSE, teh ADSPEC does not contains controlled load service overrides. Note, if TRUE, ALL override parameters will be included and must be specified.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfSRsvpSenderAdspecCLHopCount 1.3.6.1.4.1.18.3.5.16.1.1.9.1.45
If wfSRsvpSenderAdspecCLSvc is TRUE, this is the service-specific override of the hop count general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If wfSRsvpSenderAdspecCLSvc is FALSE, this returns zero or noSuchValue.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderAdspecCLPathBw 1.3.6.1.4.1.18.3.5.16.1.1.9.1.46
If wfSRsvpSenderAdspecCLSvc is TRUE, this is the service-specific override of the path bandwidth estimate general characterization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following con- ditions: the invalid bit was set the parameter was not present If wfSRsvpSenderAdspecCLSvc is FALSE, this returns zero or noSuchValue. UNITS, bits per second
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderAdspecCLMinLatency 1.3.6.1.4.1.18.3.5.16.1.1.9.1.47
If wfSRsvpSenderAdspecCLSvc is TRUE, this is the service-specific override of the minimum path latency general characterization parameter from the ADSPEC. A return of zero or noSuch- Value indicates one of the following condi- tions: the invalid bit was set the parameter was not present If wfSRsvpSenderAdspecCLSvc is FALSE, this returns zero or noSuchValue. UNITS, microseconds
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpSenderAdspecCLMtu 1.3.6.1.4.1.18.3.5.16.1.1.9.1.48
If wfSRsvpSenderAdspecCLSvc is TRUE, this is the service-specific override of the com- posed Maximum Transmission Unit general charac- terization parameter from the ADSPEC. A return of zero or noSuchValue indicates one of the following conditions: the invalid bit was set the parameter was not present If wfSRsvpSenderAdspecCLSvc is FALSE, this returns zero or noSuchValue. UNITS, bytes
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpResvTable 1.3.6.1.4.1.18.3.5.16.1.1.10
Information describing the state information displayed by statically configured reservation.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfSRsvpResvEntry

wfSRsvpResvEntry 1.3.6.1.4.1.18.3.5.16.1.1.10.1
Information describing the state information used to statically configure a reservation.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfSRsvpResvEntry  

wfSRsvpResvCreate 1.3.6.1.4.1.18.3.5.16.1.1.10.1.1
Whether to Delete this RESV RSB
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER create(1), delete(2)  

wfSRsvpResvEnable 1.3.6.1.4.1.18.3.5.16.1.1.10.1.2
Whether to Disable this RESV RSB
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfSRsvpResvStatus 1.3.6.1.4.1.18.3.5.16.1.1.10.1.3
'valid' for all active RESV messages. This object may be used to install static RESV in- formation or delete RESV information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER valid(1), invalid(2), notpres(3)  

wfSRsvpResvNumber 1.3.6.1.4.1.18.3.5.16.1.1.10.1.4
The number of this static resv. This is for SNMP Indexing purposes only and has no relation to any protocol value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfSRsvpResvDestReplicate 1.3.6.1.4.1.18.3.5.16.1.1.10.1.5
Number of sessions for which this static path state should be replicated. For each replication, wfSRsvpResvDestAddr will be incremented by one.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSRsvpResvReplicate 1.3.6.1.4.1.18.3.5.16.1.1.10.1.6
Number of senders for which this static path state should be replicated. For each replication, wfSRsvpResvAddr will be incremented by one.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSRsvpResvIntegrity 1.3.6.1.4.1.18.3.5.16.1.1.10.1.7
The contents of the integrity object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..65536)  

wfSRsvpResvDestAddr 1.3.6.1.4.1.18.3.5.16.1.1.10.1.8
The destination address used by all senders in this session. This object may not be changed when the value of the Status object is 'valid'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfSRsvpResvSenderAddr 1.3.6.1.4.1.18.3.5.16.1.1.10.1.9
The source address of the sender selected by this reservation. The value of all zeroes in- dicates 'all senders'. This object may not be changed when the value of the Status object is 'valid'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfSRsvpResvDestAddrLength 1.3.6.1.4.1.18.3.5.16.1.1.10.1.10
The length of the destination address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be changed when the value of the Status object is 'valid'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..128  

wfSRsvpResvSenderAddrLength 1.3.6.1.4.1.18.3.5.16.1.1.10.1.11
The length of the sender's address in bits. This is the CIDR Prefix Length, which for IP4 hosts and multicast addresses is 32 bits. This object may not be changed when the value of the Status object is 'valid'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..128  

wfSRsvpResvProtocol 1.3.6.1.4.1.18.3.5.16.1.1.10.1.12
The IP Protocol used by this session. This object may not be changed when the value of the Status object is 'valid'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..255  

wfSRsvpResvDestPort 1.3.6.1.4.1.18.3.5.16.1.1.10.1.13
The UDP or TCP port number used as a destina- tion port for all senders in this session. If the IP protocol in use, specified by wfSRsvpResvProtocol, is 50 (ESP) or 51 (AH), this represents a virtual destination port number. A value of zero indicates that the IP protocol in use does not have ports. This object may not be changed when the value of the Status object is 'valid'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65536  

wfSRsvpResvPort 1.3.6.1.4.1.18.3.5.16.1.1.10.1.14
The UDP or TCP port number used as a source port for this sender in this session. If the IP protocol in use, specified by wfSRsvpResvProto- col is 50 (ESP) or 51 (AH), this represents a generalized port identifier (GPI). A value of zero indicates that the IP protocol in use does not have ports. This object may not be changed when the value of the Status object is 'valid'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65536  

wfSRsvpResvFilterSpecNum 1.3.6.1.4.1.18.3.5.16.1.1.10.1.15
For SE reservation style, this is the number of filter specs. For WF and FF styles, this is ignored. If SE style, there must be wfSRsvpResvFilterSpecNum SenderAddr and SenderPort entries where SenderPort 'j' is used by SenderAddr 'j'.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSRsvpResvHopAddr 1.3.6.1.4.1.18.3.5.16.1.1.10.1.16
The address used by the next RSVP hop (which may be the ultimate receiver).
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfSRsvpResvHopLih 1.3.6.1.4.1.18.3.5.16.1.1.10.1.17
The Logical Interface Handle received from the previous RSVP hop (which may be the ultimate receiver).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSRsvpResvInterface 1.3.6.1.4.1.18.3.5.16.1.1.10.1.18
The ifIndex value of the interface on which this RESV message was most recently received.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSRsvpResvTimeValue 1.3.6.1.4.1.18.3.5.16.1.1.10.1.19
The value of the RSVP value 'R', which is the minimum period between refresh transmissions of a given PATH or RESV message on an interface. UNITS milliseconds
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpResvService 1.3.6.1.4.1.18.3.5.16.1.1.10.1.20
The QoS Service classification requested by the receiver.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER controlledDelay(1), guaranteedDelay(2), predictive(3), controlledLoad(5)  

wfSRsvpResvTSpecRate 1.3.6.1.4.1.18.3.5.16.1.1.10.1.21
The Average Bit Rate of the sender's data stream. Within a transmission burst, the ar- rival rate may be as fast as wfSRsvpResvTSpec- PeakRate (if supported by the service model); however, averaged across two or more burst in- tervals, the rate should not exceed wfSRsvpResvTSpecRate. Note that this is a prediction, often based on the general capability of a type of codec or particular encoding; the measured average rate may be significantly lower. UNITS, bits per second
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpResvTSpecPeakRate 1.3.6.1.4.1.18.3.5.16.1.1.10.1.22
The Peak Bit Rate of the sender's data stream. Traffic arrival is not expected to exceed this rate at any time, apart from the effects of jitter in the network. If not specified in the TSpec, this returns zero or noSuchValue. UNITS, bits per second
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpResvTSpecBurst 1.3.6.1.4.1.18.3.5.16.1.1.10.1.23
The size of the largest burst expected from the sender at a time. If this is less than the sender's advertised burst size, the receiver is asking the network to provide flow pacing beyond what would be provided under normal circumstances. Such pac- ing is at the network's option. UNITS, bytes
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpResvTSpecMinTU 1.3.6.1.4.1.18.3.5.16.1.1.10.1.24
The minimum message size for this flow. The policing algorithm will treat smaller messages as though they are this size.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpResvTSpecMaxTU 1.3.6.1.4.1.18.3.5.16.1.1.10.1.25
The maximum message size for this flow. The admission algorithm will reject TSpecs whose Maximum Transmission Unit, plus the interface headers, exceed the interface MTU.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpResvTSpecLevel 1.3.6.1.4.1.18.3.5.16.1.1.10.1.26
If the service is predictive or controlled- delay, this is the service level that is being requested. Otherwise, it is zero, or the agent may return noSuchValue.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..3  

wfSRsvpResvRSpecRate 1.3.6.1.4.1.18.3.5.16.1.1.10.1.27
If the requested service is Guaranteed, as specified by wfSRsvpResvService, this is the clearing rate that is being requested. Other- wise, it is zero, or the agent may return noSuchValue. UNITS, bits per second
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..7FFFFFFF  

wfSRsvpResvRSpecSlack 1.3.6.1.4.1.18.3.5.16.1.1.10.1.28
If the requested service is Guaranteed, as specified by wfSRsvpResvService, this is the delay slack. Otherwise, it is zero, or the agent may return noSuchValue.UNITS, microseconds
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSRsvpResvScopeNum 1.3.6.1.4.1.18.3.5.16.1.1.10.1.29
The number of addresses in wfSRsvpResvScope. In the absence of the scope object, this should be zero
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfSRsvpResvScope 1.3.6.1.4.1.18.3.5.16.1.1.10.1.30
The contents of the scope object, displayed as an uninterpreted string of octets. In the absence of such an object, this should be of zero length. If the length is non-zero, this contains a series of IP4 or IP6 addresses.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..65536)  

wfSRsvpResvShared 1.3.6.1.4.1.18.3.5.16.1.1.10.1.31
If TRUE, a reservation shared among senders is requested. If FALSE, a reservation specific to this sender is requested.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfSRsvpResvExplicit 1.3.6.1.4.1.18.3.5.16.1.1.10.1.32
If TRUE, individual senders are listed using Filter Specifications. If FALSE, all senders are implicitly selected. The Scope Object will contain a list of senders that need to receive this reservation request for the purpose of routing the RESV message.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfSRsvpResvPolicy 1.3.6.1.4.1.18.3.5.16.1.1.10.1.33
The contents of the policy object, displayed as an uninterpreted string of octets, including the object header. In the absence of such an object, this should be of zero length.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..65536)  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor