Wellfleet-PPP-MIB

File: Wellfleet-PPP-MIB.mib (87173 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB
Wellfleet-COMMON-MIB

Imported symbols

IpAddress Counter Gauge
OBJECT-TYPE DisplayString wfPppGroup

Defined Types

WfPppLineEntry  
SEQUENCE    
  wfPppLineDelete INTEGER
  wfPppLineDisable INTEGER
  wfPppLineState INTEGER
  wfPppLineLineNumber INTEGER
  wfPppLineLLIndex INTEGER
  wfPppLineLcpCurrentState INTEGER
  wfPppLineRestartTimer INTEGER
  wfPppLineEchoRequestFreq INTEGER
  wfPppLineEchoReplyLoss INTEGER
  wfPppLineMaxConfReq INTEGER
  wfPppLineMaxTermReq INTEGER
  wfPppLineMaxConfFail INTEGER
  wfPppLineMagicNumber Counter
  wfPppLineMru INTEGER
  wfPppLineLocalAuthProtocol INTEGER
  wfPppLineRemoteAuthProtocol INTEGER
  wfPppLineLocalPapId DisplayString
  wfPppLineLocalPapPassword DisplayString
  wfPppLineRemotePapId DisplayString
  wfPppLineRemotePapPassword DisplayString
  wfPppLineLQProtocol INTEGER
  wfPppLineDisableRemoteLQRTimer INTEGER
  wfPppLineCfgLQRRptPrd INTEGER
  wfPppLineLQRRptPrd INTEGER
  wfPppLineCfgInboundQuality INTEGER
  wfPppLineInboundQuality INTEGER
  wfPppLineCfgOutboundQuality INTEGER
  wfPppLineOutboundQuality INTEGER
  wfPppLineOutLQRs Counter
  wfPppLineInLQRs Counter
  wfPppLineChapSecret DisplayString
  wfPppLinePapFallbackDisable INTEGER
  wfPppLineChapLocalName DisplayString
  wfPppLineChapRemoteName DisplayString
  wfPppLineChapPeriodicTimer INTEGER
  wfPppLineBadPackets Counter
  wfPppLineLastBadPacket OCTET STRING
  wfPppLineLevelPktsIn Counter
  wfPppLineAllowPapReject INTEGER
  wfPppLineActiveCct INTEGER
  wfPppLineCfgAsyncMap Gauge
  wfPppLineActualAsyncMap Gauge
  wfPppLineAuthTimer INTEGER
  wfPppLineConvergenceTimer INTEGER
  wfPppLineMagicNumDisable INTEGER
  wfPppLineMyLinkDiscr INTEGER
  wfPppLinePeerLinkDiscr INTEGER
  wfPppLineCfgMru INTEGER
  wfPppLineRfc1661Compliance INTEGER
  wfPppLineLqmCurrentState INTEGER

WfPppCircuitEntry  
SEQUENCE    
  wfPppCircuitDelete INTEGER
  wfPppCircuitState INTEGER
  wfPppCircuitIpcpCurrentState INTEGER
  wfPppCircuitOsinlcpCurrentState INTEGER
  wfPppCircuitXnscpCurrentState INTEGER
  wfPppCircuitDncpCurrentState INTEGER
  wfPppCircuitAtcpCurrentState INTEGER
  wfPppCircuitIpxcpCurrentState INTEGER
  wfPppCircuitBncpCurrentState INTEGER
  wfPppCircuitVncpCurrentState INTEGER
  wfPppCircuitID INTEGER
  wfPppCircuitIpDisable INTEGER
  wfPppCircuitOsinlDisable INTEGER
  wfPppCircuitXnsDisable INTEGER
  wfPppCircuitDecnetDisable INTEGER
  wfPppCircuitAppletalkDisable INTEGER
  wfPppCircuitIpxDisable INTEGER
  wfPppCircuitBridgeDisable INTEGER
  wfPppCircuitVinesDisable INTEGER
  wfPppCircuitCfgLocalIpAddr IpAddress
  wfPppCircuitLocalIpAddr IpAddress
  wfPppCircuitCfgRemoteIpAddr IpAddress
  wfPppCircuitRemoteIpAddr IpAddress
  wfPppCircuitCfgIpxNetworkNumber OCTET STRING
  wfPppCircuitIpxNetworkNumber OCTET STRING
  wfPppCircuitIpxRemoteNodeNumber OCTET STRING
  wfPppCircuitCfgIpxRoutingProtocol INTEGER
  wfPppCircuitIpxRoutingProtocol INTEGER
  wfPppCircuitLocalIpxRouterName DisplayString
  wfPppCircuitRemoteIpxRouterName DisplayString
  wfPppCircuitIpxConfigComplete INTEGER
  wfPppCircuitCfgAtNetwork INTEGER
  wfPppCircuitAtNetwork INTEGER
  wfPppCircuitCfgLocalAtNode INTEGER
  wfPppCircuitLocalAtNode INTEGER
  wfPppCircuitCfgRemoteAtNode INTEGER
  wfPppCircuitRemoteAtNode INTEGER
  wfPppCircuitCfgAtRoutingProtocol INTEGER
  wfPppCircuitAtRoutingProtocol INTEGER
  wfPppCircuitCfgBridgeEnet INTEGER
  wfPppCircuitBridgeEnet INTEGER
  wfPppCircuitCfgBridgeFddi INTEGER
  wfPppCircuitBridgeFddi INTEGER
  wfPppCircuitCfgBridgeTokenRing INTEGER
  wfPppCircuitBridgeTokenRing INTEGER
  wfPppCircuitBadPackets Counter
  wfPppCircuitLastBadPacket OCTET STRING
  wfPppCircuitCcpCurrentState INTEGER
  wfPppCircuitCcpDisable INTEGER
  wfPppCircuitPppMode INTEGER
  wfPppCircuitMLFragPerm INTEGER
  wfPppCircuitExamPeriod INTEGER
  wfPppCircuitFullThreshold INTEGER
  wfPppCircuitPeriodsCng INTEGER
  wfPppCircuitPrefBwSlot INTEGER
  wfPppCircuitResvBwSlot INTEGER
  wfPppCircuitMLFragTriggerSize INTEGER
  wfPppCircuitMaxLinks INTEGER
  wfPppCircuitRecoverThreshold INTEGER
  wfPppCircuitPeriodsUnCng INTEGER
  wfPppCircuitHistory DisplayString
  wfPppCircuitDebugFlag INTEGER
  wfPppCircuitActualMode INTEGER
  wfPppCircuitMaxBuffers INTEGER
  wfPppCircuitLinksConfigured INTEGER
  wfPppCircuitBacpDisable INTEGER
  wfPppCircuitBacpCurrentState INTEGER
  wfPppCircuitBacpNoPhoneNum INTEGER
  wfPppCircuitIpv6Disable INTEGER
  wfPppCircuitIpv6CurrentState INTEGER
  wfPppCircuitCcpType INTEGER
  wfPppCircuitCfgCcpOptions INTEGER
  wfPppCircuitCcpOptions INTEGER
  wfPppCircuitStacLZSCheckMode INTEGER
  wfPppCircuitMLFragStrict INTEGER
  wfPppCircuitLampreyCompDisable INTEGER
  wfPppCircuitMsgLevel INTEGER
  wfPppCircuitType INTEGER
  wfPppCircuitWRCompatability INTEGER

WfPppWhoamiEntry  
SEQUENCE    
  wfPppWhoamiDelete INTEGER
  wfPppWhoamiName DisplayString
  wfPppWhoamiCircuit INTEGER
  wfPppWhoamiSecret DisplayString
  wfPppWhoamiPapPassword DisplayString
  wfPppWhoamiCctGrp INTEGER

WfPppMlStatsEntry  
SEQUENCE    
  wfPppMlStatsDelete INTEGER
  wfPppMlStatsCircuitID INTEGER
  wfPppMlStatsHomeSlot INTEGER
  wfPppMlStatsLineCnt Gauge
  wfPppMlStatsBundleSpd Gauge
  wfPppMlStatsMrru Gauge
  wfPppMlStatsEndptDisc OCTET STRING
  wfPppMlStatsTxOctets Counter
  wfPppMlStatsTxPkts Counter
  wfPppMlStatsAvgTxListLen Gauge
  wfPppMlStatsRxOctets Counter
  wfPppMlStatsRxPkts Counter
  wfPppMlStatsReasmFails Counter
  wfPppMlStatsSeqNumberLost Counter
  wfPppMlStatsSeqNumberArrivedLate Counter
  wfPppMlStatsReSeqBufferCnt Gauge
  wfPppMlStatsReSeqBufferMax Counter
  wfPppMlStatsExceededBufferMax Counter
  wfPppMlStatsLinkIdleEvents Counter
  wfPppMlStatsCalcPercent INTEGER
  wfPppMlStatsDebug INTEGER
  wfPppMlStatsReassmBufferCnt Gauge
  wfPppMlStatsReassmBufferMax Counter
  wfPppMlStatsNumPktsFragmented Counter
  wfPppMlStatsPQHiXmits Counter
  wfPppMlStatsPQNormalXmits Counter
  wfPppMlStatsPQLoXmits Counter
  wfPppMlStatsPQHiClippedPkts Counter
  wfPppMlStatsPQNormalClippedPkts Counter
  wfPppMlStatsPQLoClippedPkts Counter
  wfPppMlStatsPQIntrQHighWaterPkts Gauge
  wfPppMlStatsPQHiQHighWaterPkts Gauge
  wfPppMlStatsPQNormalQHighWaterPkts Gauge
  wfPppMlStatsPQLoQHighWaterPkts Gauge
  wfPppMlStatsPQHighWaterPktsClear INTEGER
  wfPppMlStatsPQDroppedPkts Counter
  wfPppMlStatsPQLargePkts Counter
  wfPppMlStatsPQHiTotalOctets Counter
  wfPppMlStatsPQNormalTotalOctets Counter
  wfPppMlStatsPQLoTotalOctets Counter
  wfPppMlStatsPQPktsNotQueued Counter

WfPppBapStatsEntry  
SEQUENCE    
  wfPppBapStatsDelete INTEGER
  wfPppBapStatsCircuitID INTEGER
  wfPppBapCallReqTx Counter
  wfPppBapCallRespAckTx Counter
  wfPppBapCallRespNakTx Counter
  wfPppBapCallRespFullNakTx Counter
  wfPppBapCallRespRejTx Counter
  wfPppBapCallbackReqTx Counter
  wfPppBapCallbackRespAckTx Counter
  wfPppBapCallbackRespNakTx Counter
  wfPppBapCallbackRespFullNakTx Counter
  wfPppBapCallbackRespRejTx Counter
  wfPppBapLdQueryReqTx Counter
  wfPppBapLdQueryRespAckTx Counter
  wfPppBapLdQueryRespNakTx Counter
  wfPppBapLdQueryRespFullNakTx Counter
  wfPppBapCallStatusIndFailTx Counter
  wfPppBapCallStatusIndSuccessTx Counter
  wfPppBapCallStatusRespTx Counter
  wfPppBapCallReqRx Counter
  wfPppBapCallRespAckRx Counter
  wfPppBapCallRespNakRx Counter
  wfPppBapCallRespFullNakRx Counter
  wfPppBapCallRespRejRx Counter
  wfPppBapCallbackReqRx Counter
  wfPppBapCallbackRespAckRx Counter
  wfPppBapCallbackRespNakRx Counter
  wfPppBapCallbackRespFullNakRx Counter
  wfPppBapCallbackRespRejRx Counter
  wfPppBapLdQueryReqRx Counter
  wfPppBapLdQueryRespAckRx Counter
  wfPppBapLdQueryRespNakRx Counter
  wfPppBapLdQueryRespFullNakRx Counter
  wfPppBapCallStatusIndFailRx Counter
  wfPppBapCallStatusIndSuccessRx Counter
  wfPppBapCallStatusRespRx Counter
  wfPppBapCallReqRespDiscardRx Counter
  wfPppBapCallbackReqRespDiscardRx Counter

Defined Values

wfPppLineTable 1.3.6.1.4.1.18.3.5.9.2.1
The Wellfleet PPP Line Configuration Table containing attributes dealing with the link layer and the Link Control Protocol (LCP)
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfPppLineEntry

wfPppLineEntry 1.3.6.1.4.1.18.3.5.9.2.1.1
per Wellfleet PPP line configuration parameters and counters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfPppLineEntry  

wfPppLineDelete 1.3.6.1.4.1.18.3.5.9.2.1.1.1
Create/Delete parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfPppLineDisable 1.3.6.1.4.1.18.3.5.9.2.1.1.2
Enable/Disable parameter -- Generates Open/Close events to the LCP FSM
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppLineState 1.3.6.1.4.1.18.3.5.9.2.1.1.3
PPP state variable, Not Present, Init, Down, Up
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), loopedback(4), notpresent(20)  

wfPppLineLineNumber 1.3.6.1.4.1.18.3.5.9.2.1.1.4
Instance identifier. This is the line number assigned to the driver PPP is running on top of
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfPppLineLLIndex 1.3.6.1.4.1.18.3.5.9.2.1.1.5
Instance identifier. This is the lower layer index presented to PPP by the layer immediately below it on the protocol stack. If the lower layer is a driver, the index will be 0.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfPppLineLcpCurrentState 1.3.6.1.4.1.18.3.5.9.2.1.1.6
the current state of the LCP Finite State Machine
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER starting(1), closed(2), stopped(3), closing(4), stopping(5), reqsent(6), ackrcvd(7), acksent(8), opened(9)  

wfPppLineRestartTimer 1.3.6.1.4.1.18.3.5.9.2.1.1.7
value for Restart timer in seconds
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..1000  

wfPppLineEchoRequestFreq 1.3.6.1.4.1.18.3.5.9.2.1.1.8
value for Echo-Request frequency - number of seconds between transmission of Echo-Request packets
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfPppLineEchoReplyLoss 1.3.6.1.4.1.18.3.5.9.2.1.1.9
value for Echo-Reply acceptable loss - number of unacknowledged Echo-Reply packets counted before declaring the link down
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..100  

wfPppLineMaxConfReq 1.3.6.1.4.1.18.3.5.9.2.1.1.10
value for maximum Configure-Requests - number of Configure-Request packets sent without receiving a valid Configure-Ack, Configure-Nak or Configure-Reject before assuming peer is unable to respond
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..100000  

wfPppLineMaxTermReq 1.3.6.1.4.1.18.3.5.9.2.1.1.11
value for maximum Terminate-Requests - number of Terminate-Request packets sent without receiving a Terminate-Ack before assuming peer is unable to respond
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

wfPppLineMaxConfFail 1.3.6.1.4.1.18.3.5.9.2.1.1.12
value for maximum configuration failure count - number of Configure-Nak packets sent without sending a Configure-Ack before assuming configuration is unable to converge
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

wfPppLineMagicNumber 1.3.6.1.4.1.18.3.5.9.2.1.1.13
the Magic Number being used on this line
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppLineMru 1.3.6.1.4.1.18.3.5.9.2.1.1.14
this is the MRU being used on the line (in both directions)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfPppLineLocalAuthProtocol 1.3.6.1.4.1.18.3.5.9.2.1.1.15
this is the authorization protocol we require our peer to use on our side of the link
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER passauth(49187), chap(49699), none(1)  

wfPppLineRemoteAuthProtocol 1.3.6.1.4.1.18.3.5.9.2.1.1.16
this is the authorization protocol our peer requires us to use on its side of the link
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER passauth(49187), none(1)  

wfPppLineLocalPapId 1.3.6.1.4.1.18.3.5.9.2.1.1.17
our PAP id - our peer sends this to us in an Authenticate-Request message
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfPppLineLocalPapPassword 1.3.6.1.4.1.18.3.5.9.2.1.1.18
our PAP password - our peer sends this to us in an Authenticate-Request message
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfPppLineRemotePapId 1.3.6.1.4.1.18.3.5.9.2.1.1.19
our peer's PAP id - we send this to our peer in an Authenticate-Request message
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfPppLineRemotePapPassword 1.3.6.1.4.1.18.3.5.9.2.1.1.20
our peer's PAP password - we send this to our peer in an Authenticate-Request message
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfPppLineLQProtocol 1.3.6.1.4.1.18.3.5.9.2.1.1.21
the Link Quality protocol we want to use
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER linkqr(49189), none(1)  

wfPppLineDisableRemoteLQRTimer 1.3.6.1.4.1.18.3.5.9.2.1.1.22
enable/disable our peer's LQR timer - this allows for one side to maintain the timer while the other just responds to LQR packets
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppLineCfgLQRRptPrd 1.3.6.1.4.1.18.3.5.9.2.1.1.23
this is the value in seconds between transmission of LQR packets (Reporting-Period) - it will be the same on both sides
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..120  

wfPppLineLQRRptPrd 1.3.6.1.4.1.18.3.5.9.2.1.1.24
this is the Reporting-Period, in seconds, agreed upon during negotiation - we allow the peer to negotiate down from our configured period, our maximum, but not below 1 second
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfPppLineCfgInboundQuality 1.3.6.1.4.1.18.3.5.9.2.1.1.25
the percentage of packets sent by our peer that we've successfully received (over the last 5 LQR Reporting-Periods) - 100 indicates we won't tolerate any loss
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

wfPppLineInboundQuality 1.3.6.1.4.1.18.3.5.9.2.1.1.26
the current inbound quality
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfPppLineCfgOutboundQuality 1.3.6.1.4.1.18.3.5.9.2.1.1.27
the percentage of packets sent by us that our peer successfully received (over the last 5 LQR Reporting-Periods) - 100 indicates we won't tolerate any loss
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..100  

wfPppLineOutboundQuality 1.3.6.1.4.1.18.3.5.9.2.1.1.28
the current inbound quality
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfPppLineOutLQRs 1.3.6.1.4.1.18.3.5.9.2.1.1.29
the number of Link-Quality-Report packets we've transmitted
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppLineInLQRs 1.3.6.1.4.1.18.3.5.9.2.1.1.30
the number of Link-Quality-Report packets we've received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppLineChapSecret 1.3.6.1.4.1.18.3.5.9.2.1.1.31
this CHAP secret MUST be the same on both sides of the link if CHAP is used as the Authentication protocol
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfPppLinePapFallbackDisable 1.3.6.1.4.1.18.3.5.9.2.1.1.32
if an attempt to negotiate CHAP fails, enabling this allows a fallback to PAP
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER disabled(2), enabled(1)  

wfPppLineChapLocalName 1.3.6.1.4.1.18.3.5.9.2.1.1.33
This attribute is used to assign a local CHAP Name which is used to inform our peer of our identity, during WHOAMI processing
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfPppLineChapRemoteName 1.3.6.1.4.1.18.3.5.9.2.1.1.34
This attribute is used to store our peer's CHAP Name which is used to learn our peer's identity, during WHOAMI processing
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfPppLineChapPeriodicTimer 1.3.6.1.4.1.18.3.5.9.2.1.1.35
Timer for periodic CHAP in seconds. A time of 0 disables Periodic CHAP. This timer value should long enough to allow CHAP to complete one phase before entering another.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfPppLineBadPackets 1.3.6.1.4.1.18.3.5.9.2.1.1.36
These are packets not in correct PPP format
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppLineLastBadPacket 1.3.6.1.4.1.18.3.5.9.2.1.1.37
This is the first 16 bytes of the last bad packet we received
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfPppLineLevelPktsIn 1.3.6.1.4.1.18.3.5.9.2.1.1.38
This is the count of PPP link-level packets (such as Link Control Protocol or Compression Control Protocl) which have been received.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppLineAllowPapReject 1.3.6.1.4.1.18.3.5.9.2.1.1.39
There are some peers that don't want us asking to be a PAP authenticator, so accept the Reject and remove PAP from the LCP Configure-Request if this is enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppLineActiveCct 1.3.6.1.4.1.18.3.5.9.2.1.1.40
This is the circuit number that this PPP line belongs to For the any switched lines, this will initially be -1
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfPppLineCfgAsyncMap 1.3.6.1.4.1.18.3.5.9.2.1.1.41
This is the initial seed value of Async-Control-Character-Map which will be used for LCP negotiations with the peer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

wfPppLineActualAsyncMap 1.3.6.1.4.1.18.3.5.9.2.1.1.42
Async-Control-Character-Map used by the link to escape control characters in the data packet. This is the result of LCP negotiations with the peer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfPppLineAuthTimer 1.3.6.1.4.1.18.3.5.9.2.1.1.43
value for Authentication timer in seconds
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..1000  

wfPppLineConvergenceTimer 1.3.6.1.4.1.18.3.5.9.2.1.1.44
value for Convergence timer in seconds
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..5000  

wfPppLineMagicNumDisable 1.3.6.1.4.1.18.3.5.9.2.1.1.45
Allows Magic Numbers to be disabled on this interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppLineMyLinkDiscr 1.3.6.1.4.1.18.3.5.9.2.1.1.46
value of Link Discriminator of this endpoint
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

wfPppLinePeerLinkDiscr 1.3.6.1.4.1.18.3.5.9.2.1.1.47
value of Link Discriminator of peer's endpoint
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

wfPppLineCfgMru 1.3.6.1.4.1.18.3.5.9.2.1.1.48
this is the Configured MRU being used on the line
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..4600  

wfPppLineRfc1661Compliance 1.3.6.1.4.1.18.3.5.9.2.1.1.49
Enable/Disable parameter for RFC 1661 compliance
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppLineLqmCurrentState 1.3.6.1.4.1.18.3.5.9.2.1.1.50
Indicates whether LQM is running on the line.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2)  

wfPppCircuitTable 1.3.6.1.4.1.18.3.5.9.2.2
The Wellfleet PPP Circuit Configuration Table containing attributes dealing with the network layer and each Network Control Protocol (NCP)
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfPppCircuitEntry

wfPppCircuitEntry 1.3.6.1.4.1.18.3.5.9.2.2.1
per Wellfleet circuit PPP configuration parameters and counters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfPppCircuitEntry  

wfPppCircuitDelete 1.3.6.1.4.1.18.3.5.9.2.2.1.1
Create/Delete parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfPppCircuitState 1.3.6.1.4.1.18.3.5.9.2.2.1.2
PPP state variable, Not Present, Init, Down, Up
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfPppCircuitIpcpCurrentState 1.3.6.1.4.1.18.3.5.9.2.2.1.3
the current state of the IPCP Finite State Machine
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER starting(1), closed(2), stopped(3), closing(4), stopping(5), reqsent(6), ackrcvd(7), acksent(8), opened(9)  

wfPppCircuitOsinlcpCurrentState 1.3.6.1.4.1.18.3.5.9.2.2.1.4
the current state of the OSINLCP Finite State Machine
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER starting(1), closed(2), stopped(3), closing(4), stopping(5), reqsent(6), ackrcvd(7), acksent(8), opened(9)  

wfPppCircuitXnscpCurrentState 1.3.6.1.4.1.18.3.5.9.2.2.1.5
the current state of the XNSCP Finite State Machine
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER starting(1), closed(2), stopped(3), closing(4), stopping(5), reqsent(6), ackrcvd(7), acksent(8), opened(9)  

wfPppCircuitDncpCurrentState 1.3.6.1.4.1.18.3.5.9.2.2.1.6
the current state of the DNCP Finite State Machine
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER starting(1), closed(2), stopped(3), closing(4), stopping(5), reqsent(6), ackrcvd(7), acksent(8), opened(9)  

wfPppCircuitAtcpCurrentState 1.3.6.1.4.1.18.3.5.9.2.2.1.7
the current state of the ATCP Finite State Machine
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER starting(1), closed(2), stopped(3), closing(4), stopping(5), reqsent(6), ackrcvd(7), acksent(8), opened(9)  

wfPppCircuitIpxcpCurrentState 1.3.6.1.4.1.18.3.5.9.2.2.1.8
the current state of the IPXCP Finite State Machine
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER starting(1), closed(2), stopped(3), closing(4), stopping(5), reqsent(6), ackrcvd(7), acksent(8), opened(9)  

wfPppCircuitBncpCurrentState 1.3.6.1.4.1.18.3.5.9.2.2.1.9
the current state of the BNCP Finite State Machine
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER starting(1), closed(2), stopped(3), closing(4), stopping(5), reqsent(6), ackrcvd(7), acksent(8), opened(9)  

wfPppCircuitVncpCurrentState 1.3.6.1.4.1.18.3.5.9.2.2.1.10
the current state of the VNCP Finite State Machine
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER starting(1), closed(2), stopped(3), closing(4), stopping(5), reqsent(6), ackrcvd(7), acksent(8), opened(9)  

wfPppCircuitID 1.3.6.1.4.1.18.3.5.9.2.2.1.11
cct number for this instance
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1023  

wfPppCircuitIpDisable 1.3.6.1.4.1.18.3.5.9.2.2.1.12
enable/disable IP Protocol - disabling generates a Close event to the IPCP FSM and consequently disallows IP traffic on this circuit
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppCircuitOsinlDisable 1.3.6.1.4.1.18.3.5.9.2.2.1.13
enable/disable OSI Network Layer Protocol - disabling generates a Close event to the OSINLCP FSM and consequently disallows OSI traffic on this circuit
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppCircuitXnsDisable 1.3.6.1.4.1.18.3.5.9.2.2.1.14
enable/disable XNS Protocol - disabling generates a Close event to the XNSCP FSM and consequently disallows XNS traffic on this circuit
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppCircuitDecnetDisable 1.3.6.1.4.1.18.3.5.9.2.2.1.15
enable/disable DECnet Protocol - disabling generates a Close event to the DNCP FSM and consequently disallows DECnet traffic on this circuit
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppCircuitAppletalkDisable 1.3.6.1.4.1.18.3.5.9.2.2.1.16
enable/disable AppleTalk Protocol - disabling generates a Close event to the ATCP FSM and consequently disallows AppleTalk traffic on this circuit
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppCircuitIpxDisable 1.3.6.1.4.1.18.3.5.9.2.2.1.17
enable/disable IPX Protocol - disabling generates a Close event to the IPXCP FSM and consequently disallows IPX traffic on this circuit
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppCircuitBridgeDisable 1.3.6.1.4.1.18.3.5.9.2.2.1.18
enable/disable the Bridge - disabling generates a Close event to the BNCP FSM and consequently disallows bridge traffic on this circuit
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppCircuitVinesDisable 1.3.6.1.4.1.18.3.5.9.2.2.1.19
enable/disable Vines Protocol - disabling generates a Close event to the VNCP FSM and consequently disallows Vines traffic on this circuit
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppCircuitCfgLocalIpAddr 1.3.6.1.4.1.18.3.5.9.2.2.1.20
the IP address we're going to use
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfPppCircuitLocalIpAddr 1.3.6.1.4.1.18.3.5.9.2.2.1.21
the IP address our peer wants us to use
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfPppCircuitCfgRemoteIpAddr 1.3.6.1.4.1.18.3.5.9.2.2.1.22
the IP address we want our peer to use
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

wfPppCircuitRemoteIpAddr 1.3.6.1.4.1.18.3.5.9.2.2.1.23
the IP address our peer wants to use
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfPppCircuitCfgIpxNetworkNumber 1.3.6.1.4.1.18.3.5.9.2.2.1.24
the configured IPX Network Number to be used by both us and our peer
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfPppCircuitIpxNetworkNumber 1.3.6.1.4.1.18.3.5.9.2.2.1.25
the result of IPX Network Number negotiation
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfPppCircuitIpxRemoteNodeNumber 1.3.6.1.4.1.18.3.5.9.2.2.1.26
this is what we'll tell our peer to use for node number if it sends us a 0
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING  

wfPppCircuitCfgIpxRoutingProtocol 1.3.6.1.4.1.18.3.5.9.2.2.1.27
the desired IPX Routing Protocol to be used on the link
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ripsap(2)  

wfPppCircuitIpxRoutingProtocol 1.3.6.1.4.1.18.3.5.9.2.2.1.28
the negotiated IPX Routing Protocol to be used on the link
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfPppCircuitLocalIpxRouterName 1.3.6.1.4.1.18.3.5.9.2.2.1.29
our IPX Router Name
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfPppCircuitRemoteIpxRouterName 1.3.6.1.4.1.18.3.5.9.2.2.1.30
our peer's IPX Router Name
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfPppCircuitIpxConfigComplete 1.3.6.1.4.1.18.3.5.9.2.2.1.31
indicates whether or not IPXCP converged on all required options
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER true(1), false(2)  

wfPppCircuitCfgAtNetwork 1.3.6.1.4.1.18.3.5.9.2.2.1.32
the configured AppleTalk network number - our peer must use the same number
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfPppCircuitAtNetwork 1.3.6.1.4.1.18.3.5.9.2.2.1.33
the AppleTalk network number we agreed to use
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfPppCircuitCfgLocalAtNode 1.3.6.1.4.1.18.3.5.9.2.2.1.34
the AppleTalk node number we're configured to use
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfPppCircuitLocalAtNode 1.3.6.1.4.1.18.3.5.9.2.2.1.35
our AppleTalk node number after negotiation
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfPppCircuitCfgRemoteAtNode 1.3.6.1.4.1.18.3.5.9.2.2.1.36
the AppleTalk node number we want our peer to use
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfPppCircuitRemoteAtNode 1.3.6.1.4.1.18.3.5.9.2.2.1.37
our peer's AppleTalk node number after negotiation
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfPppCircuitCfgAtRoutingProtocol 1.3.6.1.4.1.18.3.5.9.2.2.1.38
the desired AppleTalk Routing Protocol to be used on the link
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER rtmp(1), aurp(2), abgp(3)  

wfPppCircuitAtRoutingProtocol 1.3.6.1.4.1.18.3.5.9.2.2.1.39
the negotiated AppleTalk Routing Protocol to be used on the link
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfPppCircuitCfgBridgeEnet 1.3.6.1.4.1.18.3.5.9.2.2.1.40
allow/disallow Ethernet bridged frames
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppCircuitBridgeEnet 1.3.6.1.4.1.18.3.5.9.2.2.1.41
result of bridge MAC type negotiation for Ethernet
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppCircuitCfgBridgeFddi 1.3.6.1.4.1.18.3.5.9.2.2.1.42
allow/disallow FDDI bridged frames
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppCircuitBridgeFddi 1.3.6.1.4.1.18.3.5.9.2.2.1.43
result of bridge MAC type negotiation for FDDI
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppCircuitCfgBridgeTokenRing 1.3.6.1.4.1.18.3.5.9.2.2.1.44
allow/disallow Token Ring bridged frames
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppCircuitBridgeTokenRing 1.3.6.1.4.1.18.3.5.9.2.2.1.45
result of bridge MAC type negotiation for Token Ring
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppCircuitBadPackets 1.3.6.1.4.1.18.3.5.9.2.2.1.46
these are packets not in correct PPP format
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppCircuitLastBadPacket 1.3.6.1.4.1.18.3.5.9.2.2.1.47
this is the first 16 bytes of the last bad packet we received
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfPppCircuitCcpCurrentState 1.3.6.1.4.1.18.3.5.9.2.2.1.48
the current state of the CCP Finite State Machine
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER starting(1), closed(2), stopped(3), closing(4), stopping(5), reqsent(6), ackrcvd(7), acksent(8), opened(9)  

wfPppCircuitCcpDisable 1.3.6.1.4.1.18.3.5.9.2.2.1.49
enable/disable compression - disabling generates a Close event to the CCP FSM and consequently disallows compression traffic on this circuit
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppCircuitPppMode 1.3.6.1.4.1.18.3.5.9.2.2.1.50
Pre 9.0 multilines can only negotiate LCP over 1 line. The exact line which LCP will occur on is unknown. So in order to handle this situation we will wait until we receive an LCP Request before we attempt to negotiate LCP by setting the mode to PPP_MODE_PEER_SOLICITED_LCP_NEGO. If we are using this line as a single PPP Line or we are sure our peer can handle LCP on all the members of the multiline, PPP_MODE_NORMAL should be selected. Multilink is a PPP protocol extension which provides restoration of packets which arrive out of sequence, a possibility with multiple lines. Multilink monitor, in conjunction with other configuration data allows the throughput of a line to be monitored. Additional lines can be brought into the bundle and taken down dynamically in response to data traffic volume and other conditions.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER normal(1), nego(2), multilink(3), monitor(4), dynamic-monitor(5)  

wfPppCircuitMLFragPerm 1.3.6.1.4.1.18.3.5.9.2.2.1.51
This parameter allows interoperability with PPP Multilink implementations which do not allow fragmentation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER permitted(1), prohibited(2)  

wfPppCircuitExamPeriod 1.3.6.1.4.1.18.3.5.9.2.2.1.52
This indicates the interval that the Multilink bundle should be polled for possible congestion. This value is in tenths of a second
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 5..200  

wfPppCircuitFullThreshold 1.3.6.1.4.1.18.3.5.9.2.2.1.53
This is the percentage of the theoretical maximum line throughput that must be reached or exceeded before the line is considered congested.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 10..2147483647  

wfPppCircuitPeriodsCng 1.3.6.1.4.1.18.3.5.9.2.2.1.54
This is the number of consecutive periods where the line throughput is above the congestion threshold required to declare the line congested and attempt corrective action.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..100  

wfPppCircuitPrefBwSlot 1.3.6.1.4.1.18.3.5.9.2.2.1.55
This is the preferred bandwidth slot. When lines are requested to be added to the Multilink bundle this parameter denotes the slot which is asked first.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfPppCircuitResvBwSlot 1.3.6.1.4.1.18.3.5.9.2.2.1.56
This is the reserve bandwidth slot. When lines are requested to be added to the Multilink bundle this parameter denotes the slot which is asked if the preferred slot can not provide a line.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfPppCircuitMLFragTriggerSize 1.3.6.1.4.1.18.3.5.9.2.2.1.57
This is the minimum size of a packet of which Multilink will fragment.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  


wfPppCircuitRecoverThreshold 1.3.6.1.4.1.18.3.5.9.2.2.1.59
This is the recovery threshold expressed as a percentage of the theoretical maximum bundle throughput. The actual throughput must fall below this percentage in order for the BOD circuit to begin to remove lines from the Multilink bundle.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 10..2147483647  

wfPppCircuitPeriodsUnCng 1.3.6.1.4.1.18.3.5.9.2.2.1.60
This parameter is used for recovery. Once a Multilink bundle has been declared as congested, this is the number of consecutive examination periods where the queue depth is below the recovery threshold value required to declare that the bundle is no longer congested.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..100  

wfPppCircuitHistory 1.3.6.1.4.1.18.3.5.9.2.2.1.61
DEBUG parameter - This is the BOD history buffer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfPppCircuitDebugFlag 1.3.6.1.4.1.18.3.5.9.2.2.1.62
DEBUG parameter - This is the BOD Debug flag, used to control debug code for BOD.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfPppCircuitActualMode 1.3.6.1.4.1.18.3.5.9.2.2.1.63
This attribute is the actual ppp mode of the circuit after LCP has negotiated.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER normal(1), multilink(3), monitor(4), inactive(20)  

wfPppCircuitMaxBuffers 1.3.6.1.4.1.18.3.5.9.2.2.1.64
This is the maximum number of stored buffers allowed in the Multilink Receive logic for this circuit at any one time.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 10..60  

wfPppCircuitLinksConfigured 1.3.6.1.4.1.18.3.5.9.2.2.1.65
This is the current number of lines configured for this Multilink circuit.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..30  

wfPppCircuitBacpDisable 1.3.6.1.4.1.18.3.5.9.2.2.1.66
enable/disable BACP Protocol - disabling generates a Close event to the BACP FSM and consequently disallows BAP traffic on this circuit
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppCircuitBacpCurrentState 1.3.6.1.4.1.18.3.5.9.2.2.1.67
the current state of the BACP Finite State Machine
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER starting(1), closed(2), stopped(3), closing(4), stopping(5), reqsent(6), ackrcvd(7), acksent(8), opened(9)  

wfPppCircuitBacpNoPhoneNum 1.3.6.1.4.1.18.3.5.9.2.2.1.68
enable/disable sending of the No-Phone-Number-Needed option in BACP Call Request packets
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppCircuitIpv6Disable 1.3.6.1.4.1.18.3.5.9.2.2.1.69
enable/disable IPv6 Protocol - disabling generates a Close event to the IPv6CP FSM and consequently disallows IPv6 traffic on this circuit
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppCircuitIpv6CurrentState 1.3.6.1.4.1.18.3.5.9.2.2.1.70
the current state of the Ipv6 Finite State Machine
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER starting(1), closed(2), stopped(3), closing(4), stopping(5), reqsent(6), ackrcvd(7), acksent(8), opened(9)  

wfPppCircuitCcpType 1.3.6.1.4.1.18.3.5.9.2.2.1.71
Specifies whether to use CCP or Individual Link CCP
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ilccp(1), ccp(2)  

wfPppCircuitCfgCcpOptions 1.3.6.1.4.1.18.3.5.9.2.2.1.72
Specifies the compression protocol options in 1st config-request
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER all(1), oui-wcp(2), staclzs(3)  

wfPppCircuitCcpOptions 1.3.6.1.4.1.18.3.5.9.2.2.1.73
The negotiated compression protocol option
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER none(1), oui-wcp(2), staclzs(3)  

wfPppCircuitStacLZSCheckMode 1.3.6.1.4.1.18.3.5.9.2.2.1.74
Specifies the check mode for STAC LZS compression protocol. See RFC 1974 for more information.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER mode0(1), mode3(4)  

wfPppCircuitMLFragStrict 1.3.6.1.4.1.18.3.5.9.2.2.1.75
enable/disable strict fragmentation algorithm i.e. fragmenting a packet when its size exceeds the threshold regardless of what the average packet size is
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppCircuitLampreyCompDisable 1.3.6.1.4.1.18.3.5.9.2.2.1.76
enable/disable hardware compression, either from the compression daugther card on the Lamprey or the old compression daugther interface card on the link module, it tells you where the compression hardware is
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER slot1(1), slot2(2), slot3(3), slot4(4), slot5(5), slot6(6), slot7(7), slot8(8), slot9(9), slot10(10), slot11(11), slot12(12), slot13(13), slot14(14), disabled(99)  

wfPppCircuitMsgLevel 1.3.6.1.4.1.18.3.5.9.2.2.1.77
PPP Circuit log messages level. To control level of log messages DBG_MSG_ALL 0x001f0000 - 2031616 DBG_MSG_DEBUG 0x00010000 - 65536 DBG_MSG_INFO 0x00020000 - 131072 DBG_MSG_WARNING 0x00040000 - 262144 DBG_MSG_FAULT 0x00080000 - 524288 DBG_MSG_TRACE 0x00100000 - 1048576
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER all(2031616), debug(65536), info(131072), warning(262144), fault(524288), trace(1048576), infofaultwarning(917504)  

wfPppCircuitType 1.3.6.1.4.1.18.3.5.9.2.2.1.78
To differentiate between a Dial Up PPP circuit from L2TP and Leased Line
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER unknown(9), dialup(1), l2tp(2), leased(3)  

wfPppCircuitWRCompatability 1.3.6.1.4.1.18.3.5.9.2.2.1.79
Enable WebRanger compatability that allows us to accept a config-ack after receiving an invalid config-req
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppWhoamiTable 1.3.6.1.4.1.18.3.5.9.2.3
The Wellfleet PPP WHOAMI Table, containing a mapping of peer CHAP Names and the circuit numbers they map to
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfPppWhoamiEntry

wfPppWhoamiEntry 1.3.6.1.4.1.18.3.5.9.2.3.1
Map the value of this entry's CHAP Name to the value of this entry's CCT number
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfPppWhoamiEntry  

wfPppWhoamiDelete 1.3.6.1.4.1.18.3.5.9.2.3.1.1
Create/Delete parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfPppWhoamiName 1.3.6.1.4.1.18.3.5.9.2.3.1.2
Peer CHAP Name
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

wfPppWhoamiCircuit 1.3.6.1.4.1.18.3.5.9.2.3.1.3
Circuit number to map to
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfPppWhoamiSecret 1.3.6.1.4.1.18.3.5.9.2.3.1.4
Peer CHAP Secret
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfPppWhoamiPapPassword 1.3.6.1.4.1.18.3.5.9.2.3.1.5
Peer Pap Password
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString  

wfPppWhoamiCctGrp 1.3.6.1.4.1.18.3.5.9.2.3.1.6
Unnumbered circuit group to map to
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfPppMlStatsTable 1.3.6.1.4.1.18.3.5.9.2.4
The Wellfleet PPP Multilink Stats Table, containing statistics for each Multilink Circuit
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfPppMlStatsEntry

wfPppMlStatsEntry 1.3.6.1.4.1.18.3.5.9.2.4.1
per Wellfleet circuit PPP Multilink counters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfPppMlStatsEntry  

wfPppMlStatsDelete 1.3.6.1.4.1.18.3.5.9.2.4.1.1
Create/Delete parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfPppMlStatsCircuitID 1.3.6.1.4.1.18.3.5.9.2.4.1.2
cct number for this instance
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1023  

wfPppMlStatsHomeSlot 1.3.6.1.4.1.18.3.5.9.2.4.1.3
Slot on which this Multilink Control Subsystem exists
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfPppMlStatsLineCnt 1.3.6.1.4.1.18.3.5.9.2.4.1.4
Current count of lines in Multilink bundle
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfPppMlStatsBundleSpd 1.3.6.1.4.1.18.3.5.9.2.4.1.5
Current total bandwidth of Multilink bundle
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfPppMlStatsMrru 1.3.6.1.4.1.18.3.5.9.2.4.1.6
Current Maximum Receive Reconstructed Unit (MRRU) in use for Multilink bundle
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfPppMlStatsEndptDisc 1.3.6.1.4.1.18.3.5.9.2.4.1.7
Current Endpoint Discriminator in use for Multilink bundle
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING  

wfPppMlStatsTxOctets 1.3.6.1.4.1.18.3.5.9.2.4.1.8
Number of octets transmitted by Multilink
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsTxPkts 1.3.6.1.4.1.18.3.5.9.2.4.1.9
Number of packets transmitted by Multilink
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsAvgTxListLen 1.3.6.1.4.1.18.3.5.9.2.4.1.10
Average number of packets received in the transient list by the Multilink Transmit gate.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfPppMlStatsRxOctets 1.3.6.1.4.1.18.3.5.9.2.4.1.11
Number of octets received without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsRxPkts 1.3.6.1.4.1.18.3.5.9.2.4.1.12
Number of packets received by Multilink
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsReasmFails 1.3.6.1.4.1.18.3.5.9.2.4.1.13
Number of packet reassembly failures
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsSeqNumberLost 1.3.6.1.4.1.18.3.5.9.2.4.1.14
Number of Multilink packets considered to be lost on the wire
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsSeqNumberArrivedLate 1.3.6.1.4.1.18.3.5.9.2.4.1.15
Number of Multilink packets which arrive containing an old Sequence Number. IE: packets with a more current Sequence Number have already been sent up to NCP
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsReSeqBufferCnt 1.3.6.1.4.1.18.3.5.9.2.4.1.16
Number of Multilink packets currently stored in the ReSequencing buffer pool.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfPppMlStatsReSeqBufferMax 1.3.6.1.4.1.18.3.5.9.2.4.1.17
The Maximum Number of Multilink packets stored in the ReSequencing buffer pool.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsExceededBufferMax 1.3.6.1.4.1.18.3.5.9.2.4.1.18
The number of times a buffer needed to be stored by the Multilink Receive logic when the count of buffers stored, wfPppMlStatsReSeqBufferMax,was equal to the maximum allowable for this circuit, wfPppCircuitMaxBuffers.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsLinkIdleEvents 1.3.6.1.4.1.18.3.5.9.2.4.1.19
The number of times the Multilink Receive logic detected a stored buffer received on a line which has been declared idle.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsCalcPercent 1.3.6.1.4.1.18.3.5.9.2.4.1.20
enable/disable collection of Rx percentage line usage
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfPppMlStatsDebug 1.3.6.1.4.1.18.3.5.9.2.4.1.21
DEBUG parameter - this is used to control debug code for the Multilink subsystem
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfPppMlStatsReassmBufferCnt 1.3.6.1.4.1.18.3.5.9.2.4.1.22
Number of Multilink packets currently stored in the Reassembling buffer pools.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfPppMlStatsReassmBufferMax 1.3.6.1.4.1.18.3.5.9.2.4.1.23
The Maximum Number of Multilink packets stored in the Reassembling buffer pools.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsNumPktsFragmented 1.3.6.1.4.1.18.3.5.9.2.4.1.24
The Number of Multilink packets that were fragmented.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsPQHiXmits 1.3.6.1.4.1.18.3.5.9.2.4.1.25
High priority transmit count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsPQNormalXmits 1.3.6.1.4.1.18.3.5.9.2.4.1.26
Normal priority transmit count.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsPQLoXmits 1.3.6.1.4.1.18.3.5.9.2.4.1.27
Low priority transmit count
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsPQHiClippedPkts 1.3.6.1.4.1.18.3.5.9.2.4.1.28
High priority transmit clip Count
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsPQNormalClippedPkts 1.3.6.1.4.1.18.3.5.9.2.4.1.29
Normal priority transmit clip Count
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsPQLoClippedPkts 1.3.6.1.4.1.18.3.5.9.2.4.1.30
Low priority transmit clip Count
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsPQIntrQHighWaterPkts 1.3.6.1.4.1.18.3.5.9.2.4.1.31
Interrupt-priority Queue high-water mark
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfPppMlStatsPQHiQHighWaterPkts 1.3.6.1.4.1.18.3.5.9.2.4.1.32
High-priority Queue high-water mark
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfPppMlStatsPQNormalQHighWaterPkts 1.3.6.1.4.1.18.3.5.9.2.4.1.33
Normal-priority Queue high-water mark
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfPppMlStatsPQLoQHighWaterPkts 1.3.6.1.4.1.18.3.5.9.2.4.1.34
Low-priority Queue high-water mark
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

wfPppMlStatsPQHighWaterPktsClear 1.3.6.1.4.1.18.3.5.9.2.4.1.35
Attribute to clear the high-water marks. When the MIB changes, Priority Queueing (if ENABLED) checks to see if HighWaterPktsClear is different than the last time the MIB was modified in any way. If it is different, all the high water marks (see above) are set to zero.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfPppMlStatsPQDroppedPkts 1.3.6.1.4.1.18.3.5.9.2.4.1.36
Packets which were filtered in Priority Queueing
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsPQLargePkts 1.3.6.1.4.1.18.3.5.9.2.4.1.37
Large Packets which became an exception to latency rules
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsPQHiTotalOctets 1.3.6.1.4.1.18.3.5.9.2.4.1.38
Running total of High Octets transmitted when using Bandwidth Allocation dequeueing algorithm
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsPQNormalTotalOctets 1.3.6.1.4.1.18.3.5.9.2.4.1.39
Running total of Normal Octets transmitted when using Bandwidth Allocation dequeueing algorithm
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsPQLoTotalOctets 1.3.6.1.4.1.18.3.5.9.2.4.1.40
Running total of Low Octets transmitted when using Bandwidth Allocation dequeueing algorithm
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppMlStatsPQPktsNotQueued 1.3.6.1.4.1.18.3.5.9.2.4.1.41
Packets that were not Queued or Dropped by Priority Queuing
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapStatsTable 1.3.6.1.4.1.18.3.5.9.2.5
The Wellfleet PPP BAP Stats Table, containing statistics for each BACP Circuit
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfPppBapStatsEntry

wfPppBapStatsEntry 1.3.6.1.4.1.18.3.5.9.2.5.1
per Wellfleet circuit PPP BAP counters
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfPppBapStatsEntry  

wfPppBapStatsDelete 1.3.6.1.4.1.18.3.5.9.2.5.1.1
Create/Delete parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfPppBapStatsCircuitID 1.3.6.1.4.1.18.3.5.9.2.5.1.2
cct number for this instance
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 1..1023  

wfPppBapCallReqTx 1.3.6.1.4.1.18.3.5.9.2.5.1.3
Number of Call Requests transmitted by BAP
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallRespAckTx 1.3.6.1.4.1.18.3.5.9.2.5.1.4
Number of Call Responses transmitted by BAP with a Response Code of Request_Ack
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallRespNakTx 1.3.6.1.4.1.18.3.5.9.2.5.1.5
Number of Call Responses transmitted by BAP with a Response Code of Request_Nak
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallRespFullNakTx 1.3.6.1.4.1.18.3.5.9.2.5.1.6
Number of Call Responses transmitted by BAP with a Response Code of Request_Full_Nak
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallRespRejTx 1.3.6.1.4.1.18.3.5.9.2.5.1.7
Number of Call Responses transmitted by BAP with a Response Code of Request_Rej
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallbackReqTx 1.3.6.1.4.1.18.3.5.9.2.5.1.8
Number of Callback Requests transmitted by BAP
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallbackRespAckTx 1.3.6.1.4.1.18.3.5.9.2.5.1.9
Number of Callback Responses transmitted by BAP with a Response Code of Request_Ack
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallbackRespNakTx 1.3.6.1.4.1.18.3.5.9.2.5.1.10
Number of Callback Responses transmitted by BAP with a Response Code of Request_Nak
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallbackRespFullNakTx 1.3.6.1.4.1.18.3.5.9.2.5.1.11
Number of Callback Responses transmitted by BAP with a Response Code of Request_Full_Nak
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallbackRespRejTx 1.3.6.1.4.1.18.3.5.9.2.5.1.12
Number of Callback Responses transmitted by BAP with a Response Code of Request_Rej
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapLdQueryReqTx 1.3.6.1.4.1.18.3.5.9.2.5.1.13
Number of LinkDrop Query Requests transmitted by BAP
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapLdQueryRespAckTx 1.3.6.1.4.1.18.3.5.9.2.5.1.14
Number of LinkDrop Query Responses transmitted by BAP with a Response Code of Request_Ack
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapLdQueryRespNakTx 1.3.6.1.4.1.18.3.5.9.2.5.1.15
Number of LinkDrop Query Responses transmitted by BAP with a Response Code of Request_Nak
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapLdQueryRespFullNakTx 1.3.6.1.4.1.18.3.5.9.2.5.1.16
Number of LinkDrop Query Responses transmitted by BAP with a Response Code of Request_Full_Nak
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallStatusIndFailTx 1.3.6.1.4.1.18.3.5.9.2.5.1.17
Number of Call_Status_Indications transmitted by BAP with a non-zero Call Status
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallStatusIndSuccessTx 1.3.6.1.4.1.18.3.5.9.2.5.1.18
Number of Call_Status_Indications transmitted by BAP with a zero Call Status
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallStatusRespTx 1.3.6.1.4.1.18.3.5.9.2.5.1.19
Number of Call_Status_Response transmitted by BAP
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallReqRx 1.3.6.1.4.1.18.3.5.9.2.5.1.20
Number of Call Requests received by BAP
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallRespAckRx 1.3.6.1.4.1.18.3.5.9.2.5.1.21
Number of Call Responses received by BAP with a Response Code of Request_Ack
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallRespNakRx 1.3.6.1.4.1.18.3.5.9.2.5.1.22
Number of Call Responses received by BAP with a Response Code of Request_Nak
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallRespFullNakRx 1.3.6.1.4.1.18.3.5.9.2.5.1.23
Number of Call Responses received by BAP with a Response Code of Request_Full_Nak
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallRespRejRx 1.3.6.1.4.1.18.3.5.9.2.5.1.24
Number of Call Responses received by BAP with a Response Code of Request_Rej
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallbackReqRx 1.3.6.1.4.1.18.3.5.9.2.5.1.25
Number of Callback Requests received by BAP
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallbackRespAckRx 1.3.6.1.4.1.18.3.5.9.2.5.1.26
Number of Callback Responses received by BAP with a Response Code of Request_Ack
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallbackRespNakRx 1.3.6.1.4.1.18.3.5.9.2.5.1.27
Number of Callback Responses received by BAP with a Response Code of Request_Nak
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallbackRespFullNakRx 1.3.6.1.4.1.18.3.5.9.2.5.1.28
Number of Callback Responses received by BAP with a Response Code of Request_Full_Nak
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallbackRespRejRx 1.3.6.1.4.1.18.3.5.9.2.5.1.29
Number of Callback Responses received by BAP with a Response Code of Request_Rej
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapLdQueryReqRx 1.3.6.1.4.1.18.3.5.9.2.5.1.30
Number of LinkDrop Query Requests received by BAP
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapLdQueryRespAckRx 1.3.6.1.4.1.18.3.5.9.2.5.1.31
Number of LinkDrop Query Responses received by BAP with a Response Code of Request_Ack
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapLdQueryRespNakRx 1.3.6.1.4.1.18.3.5.9.2.5.1.32
Number of LinkDrop Query Responses received by BAP with a Response Code of Request_Nak
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapLdQueryRespFullNakRx 1.3.6.1.4.1.18.3.5.9.2.5.1.33
Number of LinkDrop Query Responses received by BAP with a Response Code of Request_Full_Nak
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallStatusIndFailRx 1.3.6.1.4.1.18.3.5.9.2.5.1.34
Number of Call_Status_Indications received by BAP with a non-zero Call Status
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallStatusIndSuccessRx 1.3.6.1.4.1.18.3.5.9.2.5.1.35
Number of Call_Status_Indications received by BAP with a zero Call Status
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallStatusRespRx 1.3.6.1.4.1.18.3.5.9.2.5.1.36
Number of Call_Status_Response received by BAP
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallReqRespDiscardRx 1.3.6.1.4.1.18.3.5.9.2.5.1.37
Number of Call_Response received by BAP with an old identifier.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfPppBapCallbackReqRespDiscardRx 1.3.6.1.4.1.18.3.5.9.2.5.1.38
Number of Callback_Response received by BAP with an old identifier.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter