Wellfleet-OSI-MIB

File: Wellfleet-OSI-MIB.mib (94745 bytes)

Imported modules

RFC1155-SMI	RFC-1212	RFC1213-MIB
Wellfleet-COMMON-MIB

Imported symbols

IpAddress	Counter	Opaque
OBJECT-TYPE	DisplayString	wfOsiGroup

Defined Types

WfOsiStaticRouteEntry
SEQUENCE
	wfOsiStaticRouteDelete	INTEGER
	wfOsiStaticRouteDisable	INTEGER
	wfOsiStaticRouteAddr	OCTET STRING
	wfOsiStaticRouteNibbleLength	INTEGER
	wfOsiStaticRouteNextHopIs	OCTET STRING
	wfOsiStaticRouteType	INTEGER
	wfOsiStaticRouteCost	INTEGER

WfOsiCircuitEntry
SEQUENCE
	wfOsiCircuitDelete	INTEGER
	wfOsiCircuitDisable	INTEGER
	wfOsiCircuitState	INTEGER
	wfOsiCircuitId	INTEGER
	wfOsiCircuitRouterLevel	INTEGER
	wfOsiCircuitL1DefaultMetric	INTEGER
	wfOsiCircuitL2DefaultMetric	INTEGER
	wfOsiCircuitL1DrPriority	INTEGER
	wfOsiCircuitL2DrPriority	INTEGER
	wfOsiCircuitIsisHelloTimer	INTEGER
	wfOsiCircuitEsisHelloTimer	INTEGER
	wfOsiCircuitEshConfigTime	INTEGER
	wfOsiCircuitPassword	DisplayString
	wfOsiCircuitReceivedPkts	Counter
	wfOsiCircuitSentPkts	Counter
	wfOsiCircuitDroppedPkts	Counter
	wfOsiCircuitFragmentedPdus	Counter
	wfOsiCircuitCongestionDiscards	Counter
	wfOsiCircuitAddrUnreachDiscards	Counter
	wfOsiCircuitAgedPduDiscards	Counter
	wfOsiCircuitPduFormatErrDiscards	Counter
	wfOsiCircuitUnsuppOptsDiscards	Counter
	wfOsiCircuitSentErrorReports	Counter
	wfOsiCircuitReceivedControlPdus	Counter
	wfOsiCircuitSentControlPdus	Counter
	wfOsiCircuitStateChanges	Counter
	wfOsiCircuitAdjStateChanges	Counter
	wfOsiCircuitInitFailures	Counter
	wfOsiCircuitRejectedAdjs	Counter
	wfOsiCircuitReceivedBadLsps	Counter
	wfOsiCircuitReceivedBadSnps	Counter
	wfOsiCircuitReceivedBadEshs	Counter
	wfOsiCircuitReceivedBadL1Iihs	Counter
	wfOsiCircuitReceivedBadL2Iihs	Counter
	wfOsiCircuitL1DrChanges	Counter
	wfOsiCircuitL2DrChanges	Counter
	wfOsiCircuitClnpForwarding	Counter
	wfOsiCircuitClnpDefaultLifeTime	Counter
	wfOsiCircuitClnpInReceives	Counter
	wfOsiCircuitClnpInAddrErrors	Counter
	wfOsiCircuitClnpForwPdus	Counter
	wfOsiCircuitClnpInUnknownNlps	Counter
	wfOsiCircuitClnpInDelivers	Counter
	wfOsiCircuitClnpInUnknownUlps	Counter
	wfOsiCircuitClnpSegCreates	Counter
	wfOsiCircuitClnpInOpts	Counter
	wfOsiCircuitClnpOutOpts	Counter
	wfOsiCircuitEsisEshIns	Counter
	wfOsiCircuitEsisIshOuts	Counter
	wfOsiCircuitEsisRduOuts	Counter
	wfOsiCircuitL1DesignatedRouter	OCTET STRING
	wfOsiCircuitL2DesignatedRouter	OCTET STRING
	wfOsiCircuitClnpOutEchoReplies	Counter
	wfOsiCircuitClnpOutEchoRequests	Counter
	wfOsiCircuitClnpInEchoReplies	Counter
	wfOsiCircuitClnpInEchoRequests	Counter
	wfOsiCircuitNumDynEsAdjs	Counter
	wfOsiCircuitNumDynL1Adjs	Counter
	wfOsiCircuitNumDynL2Adjs	Counter
	wfOsiCircuitNumDynPtpIsAdjs	Counter
	wfOsiCircuitNumDynPtpEsAdjs	Counter
	wfOsiCircuitBadIshReceived	Counter
	wfOsiCircuitEsisIshIns	Counter
	wfOsiCircuitIihHoldMultiplier	INTEGER
	wfOsiCircuitIshHoldMultiplier	INTEGER
	wfOsiCircuitDisableRedirect	INTEGER

WfOsiExternalAddressEntry
SEQUENCE
	wfOsiExtAddrDelete	INTEGER
	wfOsiExtAddrDisable	INTEGER
	wfOsiExtAddr	OCTET STRING
	wfOsiExtAddrCircuit	INTEGER
	wfOsiExtAddrNibbleLength	INTEGER
	wfOsiExtAddrSnpa	OCTET STRING
	wfOsiExtAddrCost	INTEGER

WfOsiStaticEsEntry
SEQUENCE
	wfOsiStaticEsDelete	INTEGER
	wfOsiStaticEsDisable	INTEGER
	wfOsiStaticEsId	OCTET STRING
	wfOsiStaticEsCircuit	INTEGER
	wfOsiStaticEsSnpa	OCTET STRING

WfOsiTrafficFilterEntry
SEQUENCE
	wfOsiTrafficFilterDelete	INTEGER
	wfOsiTrafficFilterDisable	INTEGER
	wfOsiTrafficFilterStatus	INTEGER
	wfOsiTrafficFilterCounter	Counter
	wfOsiTrafficFilterDefinition	Opaque
	wfOsiTrafficFilterReserved	INTEGER
	wfOsiTrafficFilterCircuit	INTEGER
	wfOsiTrafficFilterRuleNumber	INTEGER
	wfOsiTrafficFilterFragment	INTEGER
	wfOsiTrafficFilterName	DisplayString

WfOsiL1LspHdrEntry
SEQUENCE
	wfOsiL1LspHdrLspId	OCTET STRING
	wfOsiL1LspHdrLifetime	INTEGER
	wfOsiL1LspHdrSeqnum	INTEGER
	wfOsiL1LspHdrFlags	OCTET STRING
	wfOsiL1LspHdrCksum	OCTET STRING

WfOsiL2LspHdrEntry
SEQUENCE
	wfOsiL2LspHdrLspId	OCTET STRING
	wfOsiL2LspHdrLifetime	INTEGER
	wfOsiL2LspHdrSeqnum	INTEGER
	wfOsiL2LspHdrFlags	OCTET STRING
	wfOsiL2LspHdrCksum	OCTET STRING

WfOsiDynAdjEntry
SEQUENCE
	wfOsiDynAdjId	INTEGER
	wfOsiDynAdjDatabase	INTEGER
	wfOsiDynAdjType	INTEGER
	wfOsiDynAdjState	INTEGER
	wfOsiDynAdjCircuitId	INTEGER
	wfOsiDynAdjHoldTime	INTEGER
	wfOsiDynAdjPriority	INTEGER
	wfOsiDynAdjSnpaAddr	OCTET STRING
	wfOsiDynAdjNsapAddr	OCTET STRING
	wfOsiDynAdjLanId	OCTET STRING

WfOsiL1RouteEntry
SEQUENCE
	wfOsiL1RouteId	OCTET STRING
	wfOsiL1RoutePathSplit	INTEGER
	wfOsiL1RouteType	INTEGER
	wfOsiL1RouteNextHopSnpa	OCTET STRING
	wfOsiL1RouteNextHopId	OCTET STRING
	wfOsiL1RouteNextHopType	INTEGER
	wfOsiL1RouteNextHopCircuit	INTEGER
	wfOsiL1RouteDefaultMetricCost	INTEGER

WfOsiL2RouteEntry
SEQUENCE
	wfOsiL2RouteId	OCTET STRING
	wfOsiL2RoutePathSplit	INTEGER
	wfOsiL2RouteType	INTEGER
	wfOsiL2RouteNextHopSnpa	OCTET STRING
	wfOsiL2RouteNextHopId	OCTET STRING
	wfOsiL2RouteNextHopType	INTEGER
	wfOsiL2RouteNextHopCircuit	INTEGER
	wfOsiL2RouteDefaultMetricCost	INTEGER

WfOsiAreaAddressEntry
SEQUENCE
	wfOsiAreaAddrDelete	INTEGER
	wfOsiAreaAddrDisable	INTEGER
	wfOsiAreaAddress	OCTET STRING

WfOsiTarpCircuitEntry
SEQUENCE
	wfOsiTarpCircuitCreate	INTEGER
	wfOsiTarpCircuitEnable	INTEGER
	wfOsiTarpCircuitState	INTEGER
	wfOsiTarpCircuitCct	INTEGER
	wfOsiTarpCircuitPropagate	INTEGER
	wfOsiTarpCircuitOriginate	INTEGER
	wfOsiTarpCircuitType1Rcv	Counter
	wfOsiTarpCircuitType1Xmt	Counter
	wfOsiTarpCircuitType2Rcv	Counter
	wfOsiTarpCircuitType2Xmt	Counter
	wfOsiTarpCircuitType3Rcv	Counter
	wfOsiTarpCircuitType3Xmt	Counter
	wfOsiTarpCircuitType4Rcv	Counter
	wfOsiTarpCircuitType4Xmt	Counter
	wfOsiTarpCircuitType5Rcv	Counter
	wfOsiTarpCircuitType5Xmt	Counter
	wfOsiTarpCircuitNoBufs	Counter

WfOsiTarpLDBEntry
SEQUENCE
	wfOsiTarpLDBCreate	INTEGER
	wfOsiTarpLDBNSAP	OCTET STRING
	wfOsiTarpLDBSequence	INTEGER
	wfOsiTarpLDBCurrentTimer	INTEGER

WfOsiTarpStaticAdjEntry
SEQUENCE
	wfOsiTarpStaticAdjCreate	INTEGER
	wfOsiTarpStaticAdjEnable	INTEGER
	wfOsiTarpStaticAdjNSAP	OCTET STRING
	wfOsiTarpStaticNibbleLength	INTEGER

WfOsiTarpIgnoreAdjEntry
SEQUENCE
	wfOsiTarpIgnoreAdjCreate	INTEGER
	wfOsiTarpIgnoreAdjEnable	INTEGER
	wfOsiTarpIgnoreAdjNSAP	OCTET STRING
	wfOsiTarpIgnoreNibbleLength	INTEGER

WfOsiGreAdjEntry
SEQUENCE
	wfOsiGreAdjDelete	INTEGER
	wfOsiGreAdjDisable	INTEGER
	wfOsiGreAdjTnlNum	INTEGER
	wfOsiGreAdjConnNum	INTEGER
	wfOsiGreAdjRemoteISId	IpAddress
	wfOsiGreAdjCircuitId	INTEGER

Defined Values

wfOsi		1.3.6.1.4.1.18.3.5.6.1
OBJECT IDENTIFIER

wfOsiDelete		1.3.6.1.4.1.18.3.5.6.1.1
This value determines whether OSI is configured on this slot.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), deleted(2)

wfOsiDisable		1.3.6.1.4.1.18.3.5.6.1.2
This value determines whether OSI is to startup.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiState		1.3.6.1.4.1.18.3.5.6.1.3
This value determines whether OSI is to startup.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), init(3), notpresent(4)

wfOsiIsisVersion		1.3.6.1.4.1.18.3.5.6.1.4
This read-only parameter identifies the version number of the IS-IS protocol to which this node conforms to.
Status: mandatory	Access: read-only
OBJECT-TYPE
	DisplayString

wfOsiRouterType		1.3.6.1.4.1.18.3.5.6.1.5
This value determines whether this system is an L1-only router or L1-L2 IS.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	l1only(1), l1l2(3)

wfOsiRouterId		1.3.6.1.4.1.18.3.5.6.1.6
This value contains the system ID of this Intermediate System. If no value is entered by the user, Site Manager should supply a 6-byte value that will be unique (a MAC address would work).
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING

wfOsiLoadBal		1.3.6.1.4.1.18.3.5.6.1.7
This Boolean defines whether or not we are doing load balancing over multiple paths.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiMaxAreas		1.3.6.1.4.1.18.3.5.6.1.8
This value defines the maximum allowable number of areas addresses for the domain that this router exists in.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..1000

wfOsiMaxEs		1.3.6.1.4.1.18.3.5.6.1.9
This value defines the maximum allowable number of End Systems for the area that this router exists in.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..4000

wfOsiMaxL1Is		1.3.6.1.4.1.18.3.5.6.1.10
This value defines the maximum allowable number of L1 Intermediate Systems for the area that this router exists in.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..1000

wfOsiMaxL2Is		1.3.6.1.4.1.18.3.5.6.1.11
This value defines the maximum allowable number of L2 Intermediate Systems for the domain that this router exists in.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..1000

wfOsiMaxExtAddr		1.3.6.1.4.1.18.3.5.6.1.12
This value defines the maximum allowable number of External Addresses for the domain that this router exists in. The default value of this field is 0.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..500

wfOsiCksumIsPdus		1.3.6.1.4.1.18.3.5.6.1.13
This value indicates whether ISIS PDUs will carry a checksum.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiL1LspPassword		1.3.6.1.4.1.18.3.5.6.1.14
This assigns a password such that only L1 Lsps with the matching password will be accepted. All L1 Lsps generated by this system will contain this string in the password option.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

wfOsiL2LspPassword		1.3.6.1.4.1.18.3.5.6.1.15
This assigns a password such that only L2 Lsps with the matching password will be accepted. All L2 Lsps generated by this system will contain this string in the password option.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

wfOsiAreaAddr		1.3.6.1.4.1.18.3.5.6.1.16
This Assigns the area address for this router. This field must be filled in. If the user doesn't enter a value, then assign 490040. Site Manager must force the user to enter at least a 3-byte value for this field.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING

wfOsiAreaAddrAlias1		1.3.6.1.4.1.18.3.5.6.1.17
This Assigns the first area address alias for this router. This field does no have to be filled in, but if the user tries to enter a value, Site Manager must make sure that it is at least 3-bytes in length.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING

wfOsiAreaAddrAlias2		1.3.6.1.4.1.18.3.5.6.1.18
This Assigns the second area address alias for this router. This field does no have to be filled in, but if the user tries to enter a value, Site Manager must make sure that it is at least 3-bytes in length.
Status: obsolete	Access: read-write
OBJECT-TYPE
	OCTET STRING

wfOsiCorruptedLsps		1.3.6.1.4.1.18.3.5.6.1.19
Number of Corrupted Lsps Detected.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiL1LspDbOverloads		1.3.6.1.4.1.18.3.5.6.1.20
Number of times the L1 Lsp Database Overload event has been generated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiL2LspDbOverloads		1.3.6.1.4.1.18.3.5.6.1.21
Number of times the L2 Lsp Database Overload event has been generated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiManAddrDroppedAreas		1.3.6.1.4.1.18.3.5.6.1.22
Number of times the Manual Address Dropped from Area event has been generated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiSeqNumberSkips		1.3.6.1.4.1.18.3.5.6.1.23
Number of times the Sequence Number Skipped event has been generated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiOwnLspPurges		1.3.6.1.4.1.18.3.5.6.1.24
Number of times the Own Lsp Purged event has been generated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiOthLspPurges		1.3.6.1.4.1.18.3.5.6.1.25
Number of times the Other Lsp Purged event has been generated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiExceedMaxSeqNums		1.3.6.1.4.1.18.3.5.6.1.26
Number of times the Attempt tp Exceed Maximum Sequence Number event has been generated.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiNearestL2Is		1.3.6.1.4.1.18.3.5.6.1.27
This is the ID of the Nearest L2 system in this area.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

wfOsiMaxDynEs		1.3.6.1.4.1.18.3.5.6.1.28
This is the maximum number of dynamically learned (via Hello) End Systems allowed per slot.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..4000

wfOsiMaxDynL1Is		1.3.6.1.4.1.18.3.5.6.1.29
This is the maximum number of dynamically learned (via Hello) Level 1 Intermediate Systems allowed per slot.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..1000

wfOsiMaxDynL2Is		1.3.6.1.4.1.18.3.5.6.1.30
This is the maximum number of dynamically learned (via Hello) Level 2 Intermediate Systems allowed per slot.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..1000

wfOsiNumDynEsAdjs		1.3.6.1.4.1.18.3.5.6.1.31
Number of Dynamic ES adjs the osi master gate receives from the cct gate.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiNumDynL1Adjs		1.3.6.1.4.1.18.3.5.6.1.32
Number of Dynamic L1 adjs the osi master gate receives from the cct gate.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiNumDynL2Adjs		1.3.6.1.4.1.18.3.5.6.1.33
Number of Dynamic L2 adjs the osi master gate receives from the cct gate.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiNumL1Routes		1.3.6.1.4.1.18.3.5.6.1.34
Number of L1 Routes. WL 2.27.93
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiNumL2Routes		1.3.6.1.4.1.18.3.5.6.1.35
Number of L2 Routes. WL 2.27.93
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiNumDynPtpEsAdjs		1.3.6.1.4.1.18.3.5.6.1.36
Number of Dynamic Point-to-Point ES adjs the osi master gate receives on.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiNumDynPtpIsAdjs		1.3.6.1.4.1.18.3.5.6.1.37
Number of Dynamic Point-to-Point IS adjs the osi master gate receives on .
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiClnpSrcRtOptionDisable		1.3.6.1.4.1.18.3.5.6.1.38
Enable/Disable processing of Source Route options in CLNP PDUs. This is required for GOSIP v2 support. GOSIP prohibits processing Source Routing options.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiNumL1Lsps		1.3.6.1.4.1.18.3.5.6.1.39
Number of L1 LSPs stored in database.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiNumL2Lsps		1.3.6.1.4.1.18.3.5.6.1.40
Number of L2 LSPs stored in database.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiFletchRelaxedEnable		1.3.6.1.4.1.18.3.5.6.1.41
Enable/Disable whether non-standard Fletcher Checksums are allowed in LSP's. If enabled, a log message will be generated, otherwise the LSP will be rejected.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiStaticRouteTable		1.3.6.1.4.1.18.3.5.6.2
This table contains all the static routes for this system.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfOsiStaticRouteEntry

wfOsiStaticRouteEntry		1.3.6.1.4.1.18.3.5.6.2.1
This is the Static Route Entry for the Static Route Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfOsiStaticRouteEntry

wfOsiStaticRouteDelete		1.3.6.1.4.1.18.3.5.6.2.1.1
Create/Delete parameter for Osi Static Route Record.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), deleted(2)

wfOsiStaticRouteDisable		1.3.6.1.4.1.18.3.5.6.2.1.2
Enable/Disable parameter for this Static Route.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiStaticRouteAddr		1.3.6.1.4.1.18.3.5.6.2.1.3
This specifies the address of the static route. It is also the inst_id.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(20)

wfOsiStaticRouteNibbleLength		1.3.6.1.4.1.18.3.5.6.2.1.4
This is the length in nibbles of the static route address. It is necessary to specify it in nibbles since the static route may be an external address which can be specified in nibbles.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

wfOsiStaticRouteNextHopIs		1.3.6.1.4.1.18.3.5.6.2.1.5
This is the 6-octet ID of the next Hop IS that all data destined to wfOsiStaticRouteAddr will be forwarded to.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING

wfOsiStaticRouteType		1.3.6.1.4.1.18.3.5.6.2.1.6
This specifies whether the destination is an End System, an area, or an external Domain.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	es(9), areaaddr(11), extaddr(13)

wfOsiStaticRouteCost		1.3.6.1.4.1.18.3.5.6.2.1.7
This value is the cost to get to this address.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..1023

wfOsiCircuitTable		1.3.6.1.4.1.18.3.5.6.3
This Table contains all circuit configuration info counters available on a per circuit basis.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfOsiCircuitEntry

wfOsiCircuitEntry		1.3.6.1.4.1.18.3.5.6.3.1
This is the circuit entry record that appears in the Circuit Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfOsiCircuitEntry

wfOsiCircuitDelete		1.3.6.1.4.1.18.3.5.6.3.1.1
This value determines whether this circuit is configured.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), deleted(2)

wfOsiCircuitDisable		1.3.6.1.4.1.18.3.5.6.3.1.2
Enable/Disable parameter for this circuit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiCircuitState		1.3.6.1.4.1.18.3.5.6.3.1.3
This indicates whether the circuit state is up or down.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2)

wfOsiCircuitId		1.3.6.1.4.1.18.3.5.6.3.1.4
A unique value for each known circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiCircuitRouterLevel		1.3.6.1.4.1.18.3.5.6.3.1.5
This is the level protocol that the circuit runs. Its a bit mask to allow for some combination of L1, L2, External, ES-IS-only.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	l1(1), l2(2), l1l2(3), ext(4), l2ext(6), l1l2ext(7), esisonly(8)

wfOsiCircuitL1DefaultMetric		1.3.6.1.4.1.18.3.5.6.3.1.6
This is the default cost of using this circuit for L1 traffic.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..63

wfOsiCircuitL2DefaultMetric		1.3.6.1.4.1.18.3.5.6.3.1.7
This is the default cost of using this circuit for L2 traffic.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..63

wfOsiCircuitL1DrPriority		1.3.6.1.4.1.18.3.5.6.3.1.8
This is the priority for this system to become L1 designated router on this LAN circuit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..127

wfOsiCircuitL2DrPriority		1.3.6.1.4.1.18.3.5.6.3.1.9
This is the priority for this system to become L2 designated router on this LAN circuit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..127

wfOsiCircuitIsisHelloTimer		1.3.6.1.4.1.18.3.5.6.3.1.10
This is the period (secs) between IIH hello transmissions.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..3600

wfOsiCircuitEsisHelloTimer		1.3.6.1.4.1.18.3.5.6.3.1.11
This is the period (secs) between ISH hello transmissions.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..3600

wfOsiCircuitEshConfigTime		1.3.6.1.4.1.18.3.5.6.3.1.12
This is the suggested time between ESH transmissions from an ES went in ISHs (ESCT).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..3600

wfOsiCircuitPassword		1.3.6.1.4.1.18.3.5.6.3.1.13
This is Circuit Password for this circuit. Used to filter out Hellos from systems without the correct password.
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

wfOsiCircuitReceivedPkts		1.3.6.1.4.1.18.3.5.6.3.1.14
This is the number of pkts that have been received on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitSentPkts		1.3.6.1.4.1.18.3.5.6.3.1.15
This is the number of pkts sent out this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitDroppedPkts		1.3.6.1.4.1.18.3.5.6.3.1.16
This is the number of pkts dropped on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitFragmentedPdus		1.3.6.1.4.1.18.3.5.6.3.1.17
This is the number of pdus that had to be fragmented when forwarded out this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitCongestionDiscards		1.3.6.1.4.1.18.3.5.6.3.1.18
This is the number of PDUs dropped because of congestion.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitAddrUnreachDiscards		1.3.6.1.4.1.18.3.5.6.3.1.19
This is the number of PDUs dropped because the destination is unreachable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitAgedPduDiscards		1.3.6.1.4.1.18.3.5.6.3.1.20
This is the number of PDUs dropped because of aging.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitPduFormatErrDiscards		1.3.6.1.4.1.18.3.5.6.3.1.21
This is the number of PDUs dropped because of Format Error.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitUnsuppOptsDiscards		1.3.6.1.4.1.18.3.5.6.3.1.22
This is the number of PDUs dropped because they contain unsupported options.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitSentErrorReports		1.3.6.1.4.1.18.3.5.6.3.1.23
This is the number of error reports sent out this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitReceivedControlPdus		1.3.6.1.4.1.18.3.5.6.3.1.24
This is the number of ESIS or ISIS PDUs received on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitSentControlPdus		1.3.6.1.4.1.18.3.5.6.3.1.25
This is the number of ESIS or ISIS PDUs sent out this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitStateChanges		1.3.6.1.4.1.18.3.5.6.3.1.26
This is the number of times the circuit goes from down to up or from up to down.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitAdjStateChanges		1.3.6.1.4.1.18.3.5.6.3.1.27
This is the number of times an adjacency off of this circuit goes from down to up or from up to down state.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitInitFailures		1.3.6.1.4.1.18.3.5.6.3.1.28
This is the number of times this circuit fails to initialize.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitRejectedAdjs		1.3.6.1.4.1.18.3.5.6.3.1.29
This is the number of Adjacencies that were rejected on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitReceivedBadLsps		1.3.6.1.4.1.18.3.5.6.3.1.30
This is the number of bad Lsps received on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitReceivedBadSnps		1.3.6.1.4.1.18.3.5.6.3.1.31
This is the number of BAD Sequence Number Pdus received on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitReceivedBadEshs		1.3.6.1.4.1.18.3.5.6.3.1.32
This is the number of bad ESHs received on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitReceivedBadL1Iihs		1.3.6.1.4.1.18.3.5.6.3.1.33
This is the number of bad L1 IIHs received on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitReceivedBadL2Iihs		1.3.6.1.4.1.18.3.5.6.3.1.34
This is the number of bad L2 IIHs received on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitL1DrChanges		1.3.6.1.4.1.18.3.5.6.3.1.35
This is the number of times the L1 Designated Router has been elected on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitL2DrChanges		1.3.6.1.4.1.18.3.5.6.3.1.36
This is the number of times the L2 Designated Router has been elected on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitClnpForwarding		1.3.6.1.4.1.18.3.5.6.3.1.37
This shows whether forwarding is enabled over this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitClnpDefaultLifeTime		1.3.6.1.4.1.18.3.5.6.3.1.38
This is the lifetime included in clnp pdus generated by this router (i.e. echo and echo reply pdus, error report pdus).
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitClnpInReceives		1.3.6.1.4.1.18.3.5.6.3.1.39
This is the number of CLNP pdus received from this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitClnpInAddrErrors		1.3.6.1.4.1.18.3.5.6.3.1.40
This is the number of CLNP pdus recived from this circuit with Address format errors.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitClnpForwPdus		1.3.6.1.4.1.18.3.5.6.3.1.41
This is the number of Clnp PDUs received on this circuit that are forwarded.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitClnpInUnknownNlps		1.3.6.1.4.1.18.3.5.6.3.1.42
This is the number of Clnp PDUs received on this circuit where the network layer addressed is unknown (Bad NLPID).
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitClnpInDelivers		1.3.6.1.4.1.18.3.5.6.3.1.43
This is the number of Clnp PDUs received on this circuit whose destination is this router.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitClnpInUnknownUlps		1.3.6.1.4.1.18.3.5.6.3.1.44
This is number of Clnp PDUs received on this circuit addressed to this router where the upper layer is unknown.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitClnpSegCreates		1.3.6.1.4.1.18.3.5.6.3.1.45
This is the number of CLNP segments created from pdus received on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitClnpInOpts		1.3.6.1.4.1.18.3.5.6.3.1.46
This is the number of CLNP pdus received with an options portion.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitClnpOutOpts		1.3.6.1.4.1.18.3.5.6.3.1.47
This is the number of CLNP pdus sent with an options portion.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitEsisEshIns		1.3.6.1.4.1.18.3.5.6.3.1.48
This is the number of ESHs received from this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitEsisIshOuts		1.3.6.1.4.1.18.3.5.6.3.1.49
This is the number of ISHs sent out this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitEsisRduOuts		1.3.6.1.4.1.18.3.5.6.3.1.50
This is the number of Redirects sent out this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitL1DesignatedRouter		1.3.6.1.4.1.18.3.5.6.3.1.51
This is the ID of the L1 Designated Router on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

wfOsiCircuitL2DesignatedRouter		1.3.6.1.4.1.18.3.5.6.3.1.52
This is the ID of the L2 Designated Router on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

wfOsiCircuitClnpOutEchoReplies		1.3.6.1.4.1.18.3.5.6.3.1.53
This is the number of CLNP Echo Replies sent out this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitClnpOutEchoRequests		1.3.6.1.4.1.18.3.5.6.3.1.54
This is the number of Clnp Echo Requests sent out this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitClnpInEchoReplies		1.3.6.1.4.1.18.3.5.6.3.1.55
This is the number of CLNP Echo Replies received on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitClnpInEchoRequests		1.3.6.1.4.1.18.3.5.6.3.1.56
This is the number of CLNP Echo Requests recived on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitNumDynEsAdjs		1.3.6.1.4.1.18.3.5.6.3.1.57
This is the number of Dynamic End System Adjacencies formed on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitNumDynL1Adjs		1.3.6.1.4.1.18.3.5.6.3.1.58
This is the number of Dynamic Level 1 Intermediate System Adjacencies formed on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitNumDynL2Adjs		1.3.6.1.4.1.18.3.5.6.3.1.59
This is the number of Dynamic Level 2 Intermediate System Adjacencies formed on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitNumDynPtpIsAdjs		1.3.6.1.4.1.18.3.5.6.3.1.60
This is the number of Dynamic Intermediate System Point-to-Point Adjacencies formed on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitNumDynPtpEsAdjs		1.3.6.1.4.1.18.3.5.6.3.1.61
This is the number of Dynamic End System Point-to-Point Adjaciences formed on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitBadIshReceived		1.3.6.1.4.1.18.3.5.6.3.1.62
This is the number of bad Intermediate System Hellos received on this circuit. These will only be received on Point-to-Point circuits.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitEsisIshIns		1.3.6.1.4.1.18.3.5.6.3.1.63
This is the number of good Intermediate System Hellos received on this circuit. These will only be received on Point-to-Point circuits.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiCircuitIihHoldMultiplier		1.3.6.1.4.1.18.3.5.6.3.1.64
This is the multiplier value used to compute the hold time set in the IIH PDUs transmitted from this router. Hold time equals IIH Timer times IIH Hold Multiplier.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..5

wfOsiCircuitIshHoldMultiplier		1.3.6.1.4.1.18.3.5.6.3.1.65
This is the multiplier value used to compute the hold time set in the ISH PDUs transmitted from this router. Hold time equals IIH Timer times IIH Hold Multiplier.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..5

wfOsiCircuitDisableRedirect		1.3.6.1.4.1.18.3.5.6.3.1.66
Allow Redirects to be disabled. This is required when operating over Frame Relay in group mode in a partial mesh topology.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiExternalAddressTable		1.3.6.1.4.1.18.3.5.6.4
This is the table of External Addresses for this Router.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfOsiExternalAddressEntry

wfOsiExternalAddressEntry		1.3.6.1.4.1.18.3.5.6.4.1
This is the External Address Record for this Router.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfOsiExternalAddressEntry

wfOsiExtAddrDelete		1.3.6.1.4.1.18.3.5.6.4.1.1
This is the Create/Delete parameter for this ExtAddr entry.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), deleted(2)

wfOsiExtAddrDisable		1.3.6.1.4.1.18.3.5.6.4.1.2
Enable/Disable parameter for this ExtAddr.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiExtAddr		1.3.6.1.4.1.18.3.5.6.4.1.3
This is the prefix external address. It is also the inst_id.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(20)

wfOsiExtAddrCircuit		1.3.6.1.4.1.18.3.5.6.4.1.4
This is the circuit to go out for this adj.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiExtAddrNibbleLength		1.3.6.1.4.1.18.3.5.6.4.1.5
This is the length in nibbles of the external address.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

wfOsiExtAddrSnpa		1.3.6.1.4.1.18.3.5.6.4.1.6
This is the SNPA of the neighbor on this circuit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING

wfOsiExtAddrCost		1.3.6.1.4.1.18.3.5.6.4.1.7
This is the external metric cost to this address.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..63

wfOsiStaticEsTable		1.3.6.1.4.1.18.3.5.6.5
This is the Static ES Table for this router.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfOsiStaticEsEntry

wfOsiStaticEsEntry		1.3.6.1.4.1.18.3.5.6.5.1
This is the Static ES entry for the Static ES Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfOsiStaticEsEntry

wfOsiStaticEsDelete		1.3.6.1.4.1.18.3.5.6.5.1.1
This is the Create/Delete parameter for this Static ES entry.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), deleted(2)

wfOsiStaticEsDisable		1.3.6.1.4.1.18.3.5.6.5.1.2
Enable/Disable parameter for this Static ES.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiStaticEsId		1.3.6.1.4.1.18.3.5.6.5.1.3
This is the ESID of the neighbor.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(6)

wfOsiStaticEsCircuit		1.3.6.1.4.1.18.3.5.6.5.1.4
This is the circuit to go out for this adj.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiStaticEsSnpa		1.3.6.1.4.1.18.3.5.6.5.1.5
This is the SNPA of the neighbor on this circuit.
Status: mandatory	Access: read-write
OBJECT-TYPE
	OCTET STRING

wfOsiTrafficFilterTable		1.3.6.1.4.1.18.3.5.6.6
OSI Traffic Filters
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfOsiTrafficFilterEntry

wfOsiTrafficFilterEntry		1.3.6.1.4.1.18.3.5.6.6.1
A traffic filter definition
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfOsiTrafficFilterEntry

wfOsiTrafficFilterDelete		1.3.6.1.4.1.18.3.5.6.6.1.1
Defines the existence of the traffic filter rule: created - traffic filter exists delete - traffic filter does not exist and can be deleted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), deleted(2)

wfOsiTrafficFilterDisable		1.3.6.1.4.1.18.3.5.6.6.1.2
Defines whether or not the traffic filter rule should be used: enabled - activate the rule. disabled - inactivate the rule.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiTrafficFilterStatus		1.3.6.1.4.1.18.3.5.6.6.1.3
Defines the current status of the traffic filter: inactive - the rule is not in use. active - the rule is being used. error - the application detected an error in the rule.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	active(1), error(2), inactive(3)

wfOsiTrafficFilterCounter		1.3.6.1.4.1.18.3.5.6.6.1.4
The number of received packets that have matched this rule.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTrafficFilterDefinition		1.3.6.1.4.1.18.3.5.6.6.1.5
The filter rule definition.
Status: mandatory	Access: read-write
OBJECT-TYPE
	Opaque

wfOsiTrafficFilterReserved		1.3.6.1.4.1.18.3.5.6.6.1.6
Reserved field.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiTrafficFilterCircuit		1.3.6.1.4.1.18.3.5.6.6.1.7
The ID of the Circuit to which the filter is applied.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiTrafficFilterRuleNumber		1.3.6.1.4.1.18.3.5.6.6.1.8
ID for the rule.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiTrafficFilterFragment		1.3.6.1.4.1.18.3.5.6.6.1.9
Fragment number - for large rules.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiTrafficFilterName		1.3.6.1.4.1.18.3.5.6.6.1.10
name of the rule number
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

wfOsiL1LspHdrTable		1.3.6.1.4.1.18.3.5.6.7
2 u_int32's so the inst_id len is 2.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfOsiL1LspHdrEntry

wfOsiL1LspHdrEntry		1.3.6.1.4.1.18.3.5.6.7.1
A Record in the Level 1 Lsp Header Table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfOsiL1LspHdrEntry

wfOsiL1LspHdrLspId		1.3.6.1.4.1.18.3.5.6.7.1.1
LSPID = Source ID + Pseudo-node ID + LSP number
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(8)

wfOsiL1LspHdrLifetime		1.3.6.1.4.1.18.3.5.6.7.1.2
Lsp Lifetime
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiL1LspHdrSeqnum		1.3.6.1.4.1.18.3.5.6.7.1.3
Lsp sequence number
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiL1LspHdrFlags		1.3.6.1.4.1.18.3.5.6.7.1.4
Flags: P/ATT/LSPDBOL/IS type
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

wfOsiL1LspHdrCksum		1.3.6.1.4.1.18.3.5.6.7.1.5
Checksum
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

wfOsiL2LspHdrTable		1.3.6.1.4.1.18.3.5.6.8
2 u_int32's so the inst_id len is 2.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfOsiL2LspHdrEntry

wfOsiL2LspHdrEntry		1.3.6.1.4.1.18.3.5.6.8.1
A Record in the Lsp Header Table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfOsiL2LspHdrEntry

wfOsiL2LspHdrLspId		1.3.6.1.4.1.18.3.5.6.8.1.1
LSPID = Source ID + Pseudo-node ID + LSP number
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(8)

wfOsiL2LspHdrLifetime		1.3.6.1.4.1.18.3.5.6.8.1.2
Lsp Lifetime
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiL2LspHdrSeqnum		1.3.6.1.4.1.18.3.5.6.8.1.3
Lsp sequence number
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiL2LspHdrFlags		1.3.6.1.4.1.18.3.5.6.8.1.4
Flags: P/ATT/LSPDBOL/IS type
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

wfOsiL2LspHdrCksum		1.3.6.1.4.1.18.3.5.6.8.1.5
Checksum
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

wfOsiDynAdjTable		1.3.6.1.4.1.18.3.5.6.9
Dynamic Adjacency Table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfOsiDynAdjEntry

wfOsiDynAdjEntry		1.3.6.1.4.1.18.3.5.6.9.1
Adjacency Table - the real index is the adjacency id
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfOsiDynAdjEntry

wfOsiDynAdjId		1.3.6.1.4.1.18.3.5.6.9.1.1
Index in the Adjacency Table
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiDynAdjDatabase		1.3.6.1.4.1.18.3.5.6.9.1.2
Database into which the Adjacency is stored, 1=ES, 2=Level 1 IS, 3=Level 2 IS.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiDynAdjType		1.3.6.1.4.1.18.3.5.6.9.1.3
The type of adjacency. (see Osi_const.h)
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiDynAdjState		1.3.6.1.4.1.18.3.5.6.9.1.4
The state of the adjacency. INITIALIZING, UP or FAILED
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiDynAdjCircuitId		1.3.6.1.4.1.18.3.5.6.9.1.5
A unique value for each known circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiDynAdjHoldTime		1.3.6.1.4.1.18.3.5.6.9.1.6
Hold Time received from neighbor.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiDynAdjPriority		1.3.6.1.4.1.18.3.5.6.9.1.7
Priority to become designated router. IS only.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiDynAdjSnpaAddr		1.3.6.1.4.1.18.3.5.6.9.1.8
SNAP address for neighbor.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

wfOsiDynAdjNsapAddr		1.3.6.1.4.1.18.3.5.6.9.1.9
Neighbor address (NSAP).
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

wfOsiDynAdjLanId		1.3.6.1.4.1.18.3.5.6.9.1.10
LAN ID from Designated Router. IS only.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

wfOsiL1RoutesTable		1.3.6.1.4.1.18.3.5.6.10
This is the L1 Routes Table for this router.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfOsiL1RouteEntry

wfOsiL1RouteEntry		1.3.6.1.4.1.18.3.5.6.10.1
This is the L1 Route entry for the Routes Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfOsiL1RouteEntry

wfOsiL1RouteId		1.3.6.1.4.1.18.3.5.6.10.1.1
This is the SysID of the L1 Destination.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(6)

wfOsiL1RoutePathSplit		1.3.6.1.4.1.18.3.5.6.10.1.2
This assigns a number to each equal cost path to the destination. There can be up to 2 equal cost paths to a destination.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiL1RouteType		1.3.6.1.4.1.18.3.5.6.10.1.3
This tells what kind of a route this entry is.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiL1RouteNextHopSnpa		1.3.6.1.4.1.18.3.5.6.10.1.4
This is the SNPA of the next hop adj for this route.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

wfOsiL1RouteNextHopId		1.3.6.1.4.1.18.3.5.6.10.1.5
This is the ID of the next hop adjacency to this route. If its just an ES then it is the 6byte System ID. If the next HOP is an IS then it is the NET.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

wfOsiL1RouteNextHopType		1.3.6.1.4.1.18.3.5.6.10.1.6
This is the adj type of the next hop for this route.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiL1RouteNextHopCircuit		1.3.6.1.4.1.18.3.5.6.10.1.7
This is the circuit to forward out for this route.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiL1RouteDefaultMetricCost		1.3.6.1.4.1.18.3.5.6.10.1.8
This is the cost to from this system to this destination.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiL2RoutesTable		1.3.6.1.4.1.18.3.5.6.11
This is the L2 Routes Table for this router.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfOsiL2RouteEntry

wfOsiL2RouteEntry		1.3.6.1.4.1.18.3.5.6.11.1
This is the L2 Route entry for the Routes Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfOsiL2RouteEntry

wfOsiL2RouteId		1.3.6.1.4.1.18.3.5.6.11.1.1
This is the SysID of the L2 Destination.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(13)

wfOsiL2RoutePathSplit		1.3.6.1.4.1.18.3.5.6.11.1.2
This assigns a number to each equal cost path to the destination. There can be up to 2 equal cost paths to a destination.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiL2RouteType		1.3.6.1.4.1.18.3.5.6.11.1.3
This tells what kind of a route this entry is.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiL2RouteNextHopSnpa		1.3.6.1.4.1.18.3.5.6.11.1.4
This is the SNPA of the neighbor on this circuit.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

wfOsiL2RouteNextHopId		1.3.6.1.4.1.18.3.5.6.11.1.5
This is the ID of the next hop adjacency to this route. If its just an ES then it is the 6byte System ID. If the next HOP is an IS then it is the NET.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

wfOsiL2RouteNextHopType		1.3.6.1.4.1.18.3.5.6.11.1.6
This is the adj type of the next hop for this route.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiL2RouteNextHopCircuit		1.3.6.1.4.1.18.3.5.6.11.1.7
This is the circuit to go out for this adj.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiL2RouteDefaultMetricCost		1.3.6.1.4.1.18.3.5.6.11.1.8
This is the cost to from this system to this destination.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiDecnetTrans		1.3.6.1.4.1.18.3.5.6.12
OBJECT IDENTIFIER

wfOsiDecnetTransDelete		1.3.6.1.4.1.18.3.5.6.12.1
This value determines whether DECnet Phase 4 to Phase 5 Transition functions are configured.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), deleted(2)

wfOsiDecnetTransDisable		1.3.6.1.4.1.18.3.5.6.12.2
This value determines whether DECnet Phase 4 to Phase 5 Transition functions are enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiDecnetTransState		1.3.6.1.4.1.18.3.5.6.12.3
This value displays the state of the DECnet Phase 4 to Phase 5 Transition function.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), init(3), notpresent(4)

wfOsiDecnetTransPhase4Pkts		1.3.6.1.4.1.18.3.5.6.12.4
Number of successfully translated Phase 4 packets
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiDecnetTransSegFail		1.3.6.1.4.1.18.3.5.6.12.5
Number of times Phase 5 translation failed because the packet was segmented.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiDecnetTransNselFail		1.3.6.1.4.1.18.3.5.6.12.6
Number of times Phase 5 translation failed because the NSELs were not the same.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiDecnetTransUnrFail		1.3.6.1.4.1.18.3.5.6.12.7
Number of times Phase 5 failed to find a route to the destination.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiDecnetTransNumPhase4Es		1.3.6.1.4.1.18.3.5.6.12.8
Number of Phase 4 ES Adjacencies announced by the Phase 4 (DECnet IV) router.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiAreaAddressTable		1.3.6.1.4.1.18.3.5.6.13
This is the table of Area Addresses for this Router.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfOsiAreaAddressEntry

wfOsiAreaAddressEntry		1.3.6.1.4.1.18.3.5.6.13.1
This is the Area Address Record for this Router.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfOsiAreaAddressEntry

wfOsiAreaAddrDelete		1.3.6.1.4.1.18.3.5.6.13.1.1
This is the Create/Delete parameter for this AreaAddr entry.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), deleted(2)

wfOsiAreaAddrDisable		1.3.6.1.4.1.18.3.5.6.13.1.2
Enable/Disable parameter for this AreaAddr.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiAreaAddress		1.3.6.1.4.1.18.3.5.6.13.1.3
This is the prefix area address. It is also the inst_id.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(3..13)

wfOsiTarpEntry		1.3.6.1.4.1.18.3.5.6.14
OBJECT IDENTIFIER

wfOsiTarpCreate		1.3.6.1.4.1.18.3.5.6.14.1
This value determines whether OSI Tarp is configured on this slot.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), deleted(2)

wfOsiTarpEnable		1.3.6.1.4.1.18.3.5.6.14.2
This value dtermines if OSI Tarp is to startup.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiTarpState		1.3.6.1.4.1.18.3.5.6.14.3
This value describes the state of OSI Tarp.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), init(3), notpresent(4)

wfOsiTarpTID		1.3.6.1.4.1.18.3.5.6.14.4
This value contains the Target Identifier assigned to the router (Network Entity).
Status: mandatory	Access: read-write
OBJECT-TYPE
	DisplayString

wfOsiTarpOriginate		1.3.6.1.4.1.18.3.5.6.14.5
This value determines if TARP is allowed to originate any tarp requests.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiTarpLifetime		1.3.6.1.4.1.18.3.5.6.14.6
This value determines what the lifetime of of TARP packets originated by this router will be.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

wfOsiTarpStartSeq		1.3.6.1.4.1.18.3.5.6.14.7
This value determines what the starting sequence number of TARP packets originated by this router will be.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

wfOsiTarpNextSeq		1.3.6.1.4.1.18.3.5.6.14.8
This value determines what the next sequence number of TARP packets originated by this router will be.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

wfOsiTarpTarPro		1.3.6.1.4.1.18.3.5.6.14.9
This value describes what the Protocol Address Type field within the TARP packet must be. A value of 'FE' describes a CLNP address type.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..255

wfOsiTarpTDC		1.3.6.1.4.1.18.3.5.6.14.10
This value determines whether or not TARP uses and maintains a Tarp Data Cache.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiTarpL2TDC		1.3.6.1.4.1.18.3.5.6.14.11
This value determines whether or not TARP uses and maintains a Level 2 Tarp Data Cache.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiTarpT1		1.3.6.1.4.1.18.3.5.6.14.12
This value configures the Tarp T1 Timer - how many seconds to wait for a response to a Type1 Request PDU.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..3600

wfOsiTarpT2		1.3.6.1.4.1.18.3.5.6.14.13
This value configures the Tarp T2 Timer - how many seconds to wait for a response to a Type2 Request PDU.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..3600

wfOsiTarpT3		1.3.6.1.4.1.18.3.5.6.14.14
This value configures the Tarp T3 Timer - how many seconds to wait for a response to a Type5 Request PDU.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..3600

wfOsiTarpT4		1.3.6.1.4.1.18.3.5.6.14.15
This value configures the Tarp T4 Timer, which is used during the Error Recovery process after T2 expires.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..3600

wfOsiTarpLDBTimer		1.3.6.1.4.1.18.3.5.6.14.16
This value configures the Loop Detection Buffer's Entry Timer.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..600

wfOsiTarpLDBFlush		1.3.6.1.4.1.18.3.5.6.14.17
This value configures the timer that signals the flushing of the Loop Detection Buffer.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..86400

wfOsiTarpLDBSize		1.3.6.1.4.1.18.3.5.6.14.18
This value specifies the maximum number of entries the the Loop Detection Buffer can hold.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..5000

wfOsiTarpType1Rcv		1.3.6.1.4.1.18.3.5.6.14.19
This value counts the number of Type 1 Tarp packets received by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpType1Xmt		1.3.6.1.4.1.18.3.5.6.14.20
This value counts the number of Type 1 Tarp packets transmitted by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpType2Rcv		1.3.6.1.4.1.18.3.5.6.14.21
This value counts the number of Type 2 Tarp packets received by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpType2Xmt		1.3.6.1.4.1.18.3.5.6.14.22
This value counts the number of Type 2 Tarp packets transmitted by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpType3Rcv		1.3.6.1.4.1.18.3.5.6.14.23
This value counts the number of Type 3 Tarp packets received by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpType3Xmt		1.3.6.1.4.1.18.3.5.6.14.24
This value counts the number of Type 3 Tarp packets transmitted by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpType4Rcv		1.3.6.1.4.1.18.3.5.6.14.25
This value counts the number of Type 4 Tarp packets received by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpType4Xmt		1.3.6.1.4.1.18.3.5.6.14.26
This value counts the number of Type 4 Tarp packets transmitted by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpType5Rcv		1.3.6.1.4.1.18.3.5.6.14.27
This value counts the number of Type 5 Tarp packets received by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpType5Xmt		1.3.6.1.4.1.18.3.5.6.14.28
This value counts the number of Type 5 Tarp packets transmitted by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpCircuitTable		1.3.6.1.4.1.18.3.5.6.15
This table contains all of the Tarp interfaces for this system.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfOsiTarpCircuitEntry

wfOsiTarpCircuitEntry		1.3.6.1.4.1.18.3.5.6.15.1
This is the Tarp Interface Entry for the Tarp Interface Table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfOsiTarpCircuitEntry

wfOsiTarpCircuitCreate		1.3.6.1.4.1.18.3.5.6.15.1.1
This value determines if the Tarp Interface is to be created for this OSI interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), deleted(2)

wfOsiTarpCircuitEnable		1.3.6.1.4.1.18.3.5.6.15.1.2
This value determines if the Tarp Interface is to be enabled for this OSI interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiTarpCircuitState		1.3.6.1.4.1.18.3.5.6.15.1.3
This value reflects the state of the Tarp interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), init(3), notpresent(4)

wfOsiTarpCircuitCct		1.3.6.1.4.1.18.3.5.6.15.1.4
Circuit number for this Tarp Interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiTarpCircuitPropagate		1.3.6.1.4.1.18.3.5.6.15.1.5
This value determines if this interface will propagate transit Tarp packets out this interface.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiTarpCircuitOriginate		1.3.6.1.4.1.18.3.5.6.15.1.6
This value determines if this interface will send out Tarp packets originated by the router.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiTarpCircuitType1Rcv		1.3.6.1.4.1.18.3.5.6.15.1.7
This value counts the number of Type 1 Tarp packets received by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpCircuitType1Xmt		1.3.6.1.4.1.18.3.5.6.15.1.8
This value counts the number of Type 1 Tarp packets transmitted by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpCircuitType2Rcv		1.3.6.1.4.1.18.3.5.6.15.1.9
This value counts the number of Type 2 Tarp packets received by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpCircuitType2Xmt		1.3.6.1.4.1.18.3.5.6.15.1.10
This value counts the number of Type 2 Tarp packets transmitted by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpCircuitType3Rcv		1.3.6.1.4.1.18.3.5.6.15.1.11
This value counts the number of Type 3 Tarp packets received by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpCircuitType3Xmt		1.3.6.1.4.1.18.3.5.6.15.1.12
This value counts the number of Type 3 Tarp packets transmitted by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpCircuitType4Rcv		1.3.6.1.4.1.18.3.5.6.15.1.13
This value counts the number of Type 4 Tarp packets received by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpCircuitType4Xmt		1.3.6.1.4.1.18.3.5.6.15.1.14
This value counts the number of Type 4 Tarp packets transmitted by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpCircuitType5Rcv		1.3.6.1.4.1.18.3.5.6.15.1.15
This value counts the number of Type 5 Tarp packets received by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpCircuitType5Xmt		1.3.6.1.4.1.18.3.5.6.15.1.16
This value counts the number of Type 5 Tarp packets transmitted by this interface.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpCircuitNoBufs		1.3.6.1.4.1.18.3.5.6.15.1.17
This value represents the number of times Tarp tried to allocate a buffer but was unable.
Status: mandatory	Access: read-only
OBJECT-TYPE
	Counter

wfOsiTarpLDBTable		1.3.6.1.4.1.18.3.5.6.16
Table of wfOsiTarpLDBEntry's.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfOsiTarpLDBEntry

wfOsiTarpLDBEntry		1.3.6.1.4.1.18.3.5.6.16.1
Each entry in the Loop Detection Buffer.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfOsiTarpLDBEntry

wfOsiTarpLDBCreate		1.3.6.1.4.1.18.3.5.6.16.1.1
Specifies the creation or deletion of the instance.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), deleted(2)

wfOsiTarpLDBNSAP		1.3.6.1.4.1.18.3.5.6.16.1.2
The NSAP address for this entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING

wfOsiTarpLDBSequence		1.3.6.1.4.1.18.3.5.6.16.1.3
The sequence number for this LDB entry.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	0..65535

wfOsiTarpLDBCurrentTimer		1.3.6.1.4.1.18.3.5.6.16.1.4
Current timer for this LDB Entry.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	1..600

wfOsiTarpStaticAdjTable		1.3.6.1.4.1.18.3.5.6.17
Table of wfOsiTarpStaticAdjEntry's.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfOsiTarpStaticAdjEntry

wfOsiTarpStaticAdjEntry		1.3.6.1.4.1.18.3.5.6.17.1
This is the static adjacency record that appears in the adjacency table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfOsiTarpStaticAdjEntry

wfOsiTarpStaticAdjCreate		1.3.6.1.4.1.18.3.5.6.17.1.1
This value determines if this instance should be created or deleted.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), deleted(2)

wfOsiTarpStaticAdjEnable		1.3.6.1.4.1.18.3.5.6.17.1.2
This value determines if the Static Adjacency should be enabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiTarpStaticAdjNSAP		1.3.6.1.4.1.18.3.5.6.17.1.3
This specifies the address of the Static Adjacency. It is also the instance ID.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(20)

wfOsiTarpStaticNibbleLength		1.3.6.1.4.1.18.3.5.6.17.1.4
Describes the number of nibbles in the Static NSAP Address.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

wfOsiTarpIgnoreAdjTable		1.3.6.1.4.1.18.3.5.6.18
This table contains all the adjacency entries that should be ignored.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfOsiTarpIgnoreAdjEntry

wfOsiTarpIgnoreAdjEntry		1.3.6.1.4.1.18.3.5.6.18.1
This is the ignore static route entry for the wfOsiTarpIgnoreAdj table.
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfOsiTarpIgnoreAdjEntry

wfOsiTarpIgnoreAdjCreate		1.3.6.1.4.1.18.3.5.6.18.1.1
Signifies this instance should be created.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), deleted(2)

wfOsiTarpIgnoreAdjEnable		1.3.6.1.4.1.18.3.5.6.18.1.2
This value determines if this instance should be enabled or disabled.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiTarpIgnoreAdjNSAP		1.3.6.1.4.1.18.3.5.6.18.1.3
Identifies the OSI Adjacency that should be ignored.
Status: mandatory	Access: read-only
OBJECT-TYPE
	OCTET STRING	Size(20)

wfOsiTarpIgnoreNibbleLength		1.3.6.1.4.1.18.3.5.6.18.1.4
Describes the number of nibbles in the Static NSAP Address for the Ignore Static Route.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER

wfOsiGreAdjTable		1.3.6.1.4.1.18.3.5.6.19
Gre Adjacency Table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfOsiGreAdjEntry

wfOsiGreAdjEntry		1.3.6.1.4.1.18.3.5.6.19.1
GRE Adjacency Entry
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfOsiGreAdjEntry

wfOsiGreAdjDelete		1.3.6.1.4.1.18.3.5.6.19.1.1
Delete/Create parameter.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), deleted(2)

wfOsiGreAdjDisable		1.3.6.1.4.1.18.3.5.6.19.1.2
Enable/Disable parameter
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfOsiGreAdjTnlNum		1.3.6.1.4.1.18.3.5.6.19.1.3
GRE tunnel number from GRE MIB
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiGreAdjConnNum		1.3.6.1.4.1.18.3.5.6.19.1.4
GRE remote tunnel connection number from GRE MIB.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfOsiGreAdjRemoteISId		1.3.6.1.4.1.18.3.5.6.19.1.5
This is the Physical IP address of the Destination.
Status: mandatory	Access: read-write
OBJECT-TYPE
	IpAddress

wfOsiGreAdjCircuitId		1.3.6.1.4.1.18.3.5.6.19.1.6
Circuit number on which this link in configured.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER