Wellfleet-LAPB-MIB

File: Wellfleet-LAPB-MIB.mib (16170 bytes)

Imported modules

RFC1155-SMI RFC-1212 Wellfleet-COMMON-MIB

Imported symbols

Counter OBJECT-TYPE wfDataLink

Defined Types

WfLapbEntry  
SEQUENCE    
  wfLapbDelete INTEGER
  wfLapbDisable INTEGER
  wfLapbState INTEGER
  wfLapbLineNumber INTEGER
  wfLapbLLIndex INTEGER
  wfLapbCct INTEGER
  wfLapbStationType INTEGER
  wfLapbControlField INTEGER
  wfLapbN1FrameSize INTEGER
  wfLapbKWindowSize INTEGER
  wfLapbN2RxmitCount INTEGER
  wfLapbT1AckTimer INTEGER
  wfLapbT2AckDelayTimer INTEGER
  wfLapbT3DisconnectTimer INTEGER
  wfLapbT4IdleTimer INTEGER
  wfLapbActionInitiate INTEGER
  wfLapbXidDisable INTEGER
  wfLapbCommandAddress INTEGER
  wfLapbResponseAddress INTEGER
  wfLapbWanProtocol INTEGER
  wfLapbRxOctets Counter
  wfLapbRxFrames Counter
  wfLapbTxOctets Counter
  wfLapbTxFrames Counter
  wfLapbReXmits Counter
  wfLapbRejectsTx Counter
  wfLapbRejectsRx Counter
  wfLapbFrameRejectsTx Counter
  wfLapbFrameRejectsRx Counter
  wfLapbRRsTx Counter
  wfLapbRRsRx Counter
  wfLapbRNRsTx Counter
  wfLapbRNRsRx Counter
  wfLapbResets Counter
  wfLapbNormalDisc Counter
  wfLapbAbnormalDisc Counter
  wfLapbSetupAllowed Counter
  wfLapbSetupRefused Counter
  wfLapbNetworkType INTEGER
  wfLapbIdleRRFrames INTEGER
  wfLapbClientType INTEGER
  wfLapbRetransmitTimer INTEGER

Defined Values

wfLapbTable 1.3.6.1.4.1.18.3.5.1.8
********************************************************************** LAPB MIB record *********************************************************************
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfLapbEntry

wfLapbEntry 1.3.6.1.4.1.18.3.5.1.8.1
An entry in the LAPB table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfLapbEntry  

wfLapbDelete 1.3.6.1.4.1.18.3.5.1.8.1.1
Create/Delete parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfLapbDisable 1.3.6.1.4.1.18.3.5.1.8.1.2
Enable/Disable parameter
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfLapbState 1.3.6.1.4.1.18.3.5.1.8.1.3
Line Driver state variable, Not Present, DSR Wait, Init, Down, Up
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpresent(4)  

wfLapbLineNumber 1.3.6.1.4.1.18.3.5.1.8.1.4
Instance identifier, Line Number, filled in by LAPB
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfLapbLLIndex 1.3.6.1.4.1.18.3.5.1.8.1.5
Instance identifier, Lower Layer Index, filled in by LAPB
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfLapbCct 1.3.6.1.4.1.18.3.5.1.8.1.6
CCT number for this LAPB subsystem, it is associated with the driver or application running underneath it.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfLapbStationType 1.3.6.1.4.1.18.3.5.1.8.1.7
Identifies the desired station type of this interface. A value of DxE indicates XID enabled but not negotiation has not yet taken place.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER dte(1), dce(2), dxe(3)  

wfLapbControlField 1.3.6.1.4.1.18.3.5.1.8.1.8
This parameter establishes the desired size of the sequence numbers used to number frames.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER modulo8(1), modulo128(2)  

wfLapbN1FrameSize 1.3.6.1.4.1.18.3.5.1.8.1.9
The default maximum N1 frame size desired in number of bytes for a frame transmitted by the DxE. This excludes flags and 0 bits inserted for transparency.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 3..4500  

wfLapbKWindowSize 1.3.6.1.4.1.18.3.5.1.8.1.10
The default transmit and receive window size for this Interface. This is the maximum number of unacknowledged sequence frames that may be outstanding from this DxE at any one time.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..127  

wfLapbN2RxmitCount 1.3.6.1.4.1.18.3.5.1.8.1.11
The default N2 retry count indicates the number of retransmission attempts which will be tried per frame before a line is determined to be down. The retry count is max attempts following expiration of the T1 timer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..64  

wfLapbT1AckTimer 1.3.6.1.4.1.18.3.5.1.8.1.12
The default T1 timer for this interface. This specifies the maximum time in tenths of seconds to wait for an acknowledgment of a frame.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..9999  

wfLapbT2AckDelayTimer 1.3.6.1.4.1.18.3.5.1.8.1.13
The default T2 timer for this interface. This specifies the maximum time in seconds to wait before sending an acknowledgment for a sequenced frame. A value of one means there will be no delay in acknowledgment generation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..9999  

wfLapbT3DisconnectTimer 1.3.6.1.4.1.18.3.5.1.8.1.14
The T3 timer for this interface. This specifies the time in seconds to wait before considering the link disconnected. A value of one indicates the link will be considered disconnected upon completion of the frame exchange to disconnect the link.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..9999  

wfLapbT4IdleTimer 1.3.6.1.4.1.18.3.5.1.8.1.15
The T4 timer for this interface. This specifies the maximum time in seconds to allow without frames being exchanged on the data link. Not implemented for this project.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..9999  

wfLapbActionInitiate 1.3.6.1.4.1.18.3.5.1.8.1.16
This identifies the action LAPB will take to initiate link set-up.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER active(1), passive(2), activeDisc(3)  

wfLapbXidDisable 1.3.6.1.4.1.18.3.5.1.8.1.17
XID enable/disable parameter. This parameter is used to enable or disable transmission/reception of Test XID frames.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfLapbCommandAddress 1.3.6.1.4.1.18.3.5.1.8.1.18
The local command address parameter contains the DTE or DCE value expressed as a single octet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER dte(1), dce(3)  

wfLapbResponseAddress 1.3.6.1.4.1.18.3.5.1.8.1.19
The local response address parameter contains the DTE or DCE value expressed as a single octet.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER dte(3), dce(1)  

wfLapbWanProtocol 1.3.6.1.4.1.18.3.5.1.8.1.20
WAN protocol selection is provided via this parameter. The supported protocols can be selected per interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER standard(1), x25(6), lapb(7)  

wfLapbRxOctets 1.3.6.1.4.1.18.3.5.1.8.1.21
Number of octets received without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLapbRxFrames 1.3.6.1.4.1.18.3.5.1.8.1.22
Number of frames received without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLapbTxOctets 1.3.6.1.4.1.18.3.5.1.8.1.23
Number of octets transmitted without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLapbTxFrames 1.3.6.1.4.1.18.3.5.1.8.1.24
Number of frames transmitted without error
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLapbReXmits 1.3.6.1.4.1.18.3.5.1.8.1.25
Number of retransmission occurances
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLapbRejectsTx 1.3.6.1.4.1.18.3.5.1.8.1.26
Number of reject frames which were transmitted
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLapbRejectsRx 1.3.6.1.4.1.18.3.5.1.8.1.27
Number of reject frames which were received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLapbFrameRejectsTx 1.3.6.1.4.1.18.3.5.1.8.1.28
Number of Frame Rejects transmitted
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLapbFrameRejectsRx 1.3.6.1.4.1.18.3.5.1.8.1.29
Number of Frame Rejects received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLapbRRsTx 1.3.6.1.4.1.18.3.5.1.8.1.30
Number of Receiver Ready frames transmitted
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLapbRRsRx 1.3.6.1.4.1.18.3.5.1.8.1.31
Number of Receiver Ready frames received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLapbRNRsTx 1.3.6.1.4.1.18.3.5.1.8.1.32
Number of Receiver Not Ready frames transmitted
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLapbRNRsRx 1.3.6.1.4.1.18.3.5.1.8.1.33
Number of Receiver Not Ready frames received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLapbResets 1.3.6.1.4.1.18.3.5.1.8.1.34
Number of Link Connection Resets
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLapbNormalDisc 1.3.6.1.4.1.18.3.5.1.8.1.35
Number of normal link disconnections
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLapbAbnormalDisc 1.3.6.1.4.1.18.3.5.1.8.1.36
Number of abnormal link disconnections
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLapbSetupAllowed 1.3.6.1.4.1.18.3.5.1.8.1.37
Number of successful link connections
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLapbSetupRefused 1.3.6.1.4.1.18.3.5.1.8.1.38
Number of unsuccessful link connections
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfLapbNetworkType 1.3.6.1.4.1.18.3.5.1.8.1.39
The types GOSIP and NET2 are used in conjunction with the X.25 network
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER gosip(1), net2(2)  

wfLapbIdleRRFrames 1.3.6.1.4.1.18.3.5.1.8.1.40
XID enable/disable parameter. This parameter is used to enable or disable transmission/reception of Test XID frames.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

wfLapbClientType 1.3.6.1.4.1.18.3.5.1.8.1.41
This parameter is used to describe the client above the LAPB protocol layer. By default, the client is the X.25 Packet layer. Currently, the only other selection is ipex or none.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER none(1), x25(2), ipex(3)  

wfLapbRetransmitTimer 1.3.6.1.4.1.18.3.5.1.8.1.42
The Retransmit timer for this interface. This specifies the maximum time in seconds to allow without retransmitting frames after RNR and RR received on this interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255