Wellfleet-DVMRP-MIB

File: Wellfleet-DVMRP-MIB.mib (56206 bytes)

Imported modules

RFC1155-SMI RFC-1212 Wellfleet-COMMON-MIB

Imported symbols

IpAddress Counter Gauge
OBJECT-TYPE wfDvmrpGroup

Defined Types

WfDvmrpCircuitEntry  
SEQUENCE    
  wfDvmrpCircuitCreate INTEGER
  wfDvmrpCircuitEnable INTEGER
  wfDvmrpCircuitState INTEGER
  wfDvmrpCircuitCCT INTEGER
  wfDvmrpCircuitRouteEnable INTEGER
  wfDvmrpCircuitMetric INTEGER
  wfDvmrpCircuitRouteThreshold INTEGER
  wfDvmrpCircuitInPkts Counter
  wfDvmrpCircuitOutPkts Counter
  wfDvmrpCircuitInRouteUpdates Counter
  wfDvmrpCircuitOutRouteUpdates Counter
  wfDvmrpCircuitInPktDiscards Counter
  wfDvmrpCircuitOutPktDiscards Counter
  wfDvmrpCircuitFwdCacheSize INTEGER
  wfDvmrpCircuitFwdCacheTTL INTEGER
  wfDvmrpCircuitAdvertiseSelf INTEGER
  wfDvmrpCircuitFwdCacheEntries INTEGER
  wfDvmrpCircuitInPrunePkts Counter
  wfDvmrpCircuitOutPrunePkts Counter
  wfDvmrpCircuitInGraftPkts Counter
  wfDvmrpCircuitOutGraftPkts Counter
  wfDvmrpCircuitInGraftAckPkts Counter
  wfDvmrpCircuitOutGraftAckPkts Counter
  wfDvmrpCircuitDefaultRouteSupply INTEGER
  wfDvmrpCircuitDefaultRouteListen INTEGER
  wfDvmrpCircuitReportDependProbe INTEGER
  wfDvmrpCircuitPruneLifeTime INTEGER
  wfDvmrpCircuitAcceptAggregateRoutes INTEGER
  wfDvmrpCircuitAnnounceAggregatedRoutes INTEGER

WfDvmrpTunnelEntry  
SEQUENCE    
  wfDvmrpTunnelCreate INTEGER
  wfDvmrpTunnelEnable INTEGER
  wfDvmrpTunnelState INTEGER
  wfDvmrpTunnelCCT INTEGER
  wfDvmrpTunnelRemoteRouterIpAddress IpAddress
  wfDvmrpTunnelEncapsMode INTEGER
  wfDvmrpTunnelMetric INTEGER
  wfDvmrpTunnelThreshold INTEGER
  wfDvmrpTunnelInPkts Counter
  wfDvmrpTunnelOutPkts Counter
  wfDvmrpTunnelInRouteUpdates Counter
  wfDvmrpTunnelOutRouteUpdates Counter
  wfDvmrpTunnelInPktDiscards Counter
  wfDvmrpTunnelOutPktDiscards Counter
  wfDvmrpTunnelLocalRouterIpAddress IpAddress
  wfDvmrpTunnelFwdCacheSize INTEGER
  wfDvmrpTunnelFwdCacheTTL INTEGER
  wfDvmrpTunnelFwdCacheEntries INTEGER
  wfDvmrpTunnelInPrunePkts Counter
  wfDvmrpTunnelOutPrunePkts Counter
  wfDvmrpTunnelInGraftPkts Counter
  wfDvmrpTunnelOutGraftPkts Counter
  wfDvmrpTunnelInGraftAckPkts Counter
  wfDvmrpTunnelOutGraftAckPkts Counter
  wfDvmrpTunnelDefaultRouteSupply INTEGER
  wfDvmrpTunnelDefaultRouteListen INTEGER
  wfDvmrpTunnelCtrlMsgMode INTEGER
  wfDvmrpTunnelReportDependProbe INTEGER
  wfDvmrpTunnelPruneLifeTime INTEGER
  wfDvmrpTunnelAcceptAggregateRoutes INTEGER
  wfDvmrpTunnelAnnounceAggregatedRoutes INTEGER

WfDvmrpRouteEntry  
SEQUENCE    
  wfDvmrpRouteSourceNetwork IpAddress
  wfDvmrpRouteSourceMask IpAddress
  wfDvmrpRouteNextHopRouter IpAddress
  wfDvmrpRouteNextHopInterfaceCCT INTEGER
  wfDvmrpRouteNextHopInterfaceTunnelId IpAddress
  wfDvmrpRouteNextHopInterfaceLocalTunnelId IpAddress
  wfDvmrpRouteTimer INTEGER
  wfDvmrpRouteState INTEGER
  wfDvmrpRouteMetric INTEGER
  wfDvmrpRouteProtocol INTEGER
  wfDvmrpRouteType INTEGER
  wfDvmrpRouteAggregatedType INTEGER

WfDvmrpRouteInterfaceEntry  
SEQUENCE    
  wfDvmrpRouteInterfaceSourceNetwork IpAddress
  wfDvmrpRouteInterfaceSourceMask IpAddress
  wfDvmrpRouteInterfaceNextHopInterfaceCCT INTEGER
  wfDvmrpRouteInterfaceNextHopInterfaceLocalTunnelId IpAddress
  wfDvmrpRouteInterfaceNextHopInterfaceTunnelId IpAddress
  wfDvmrpRouteInterfaceState INTEGER
  wfDvmrpRouteInterfaceDominantRouter IpAddress
  wfDvmrpRouteInterfaceSubordinateRouter IpAddress
  wfDvmrpRouteInterfaceHoldDownTimer INTEGER
  wfDvmrpRouteInterfaceSPInDiscards Counter
  wfDvmrpRouteInterfaceSPOutDiscards Counter
  wfDvmrpRouteInterfaceThresholdOutDiscards Counter
  wfDvmrpRouteInterfaceInSuccessfulPkts Counter
  wfDvmrpRouteInterfaceOutSuccessfulPkts Counter
  wfDvmrpRouteInterfaceParentCCT INTEGER
  wfDvmrpRouteInterfaceParentLocalTunnelId IpAddress
  wfDvmrpRouteInterfaceParentTunnelId IpAddress

WfDvmrpNeighboringRouterEntry  
SEQUENCE    
  wfDvmrpNeighboringRouterCCT INTEGER
  wfDvmrpNeighboringRouterLocalTunnelId IpAddress
  wfDvmrpNeighboringRouterTunnelId IpAddress
  wfDvmrpNeighboringRouterIpAddr IpAddress
  wfDvmrpNeighboringRouterState INTEGER
  wfDvmrpNeighboringRouterTimer INTEGER
  wfDvmrpNeighboringRouterGenId INTEGER
  wfDvmrpNeighboringRouterMajorVersion INTEGER
  wfDvmrpNeighboringRouterMinorVersion INTEGER
  wfDvmrpNeighboringRouterCapabilities INTEGER

Defined Values

wfDvmrpBase 1.3.6.1.4.1.18.3.5.3.12.1
OBJECT IDENTIFIER    

wfDvmrpBaseCreate 1.3.6.1.4.1.18.3.5.3.12.1.1
This entry will provide the base configuration for the DVMRP multicast support on the router.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfDvmrpBaseEnable 1.3.6.1.4.1.18.3.5.3.12.1.2
Enable or disable DVMRP support in router
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDvmrpBaseState 1.3.6.1.4.1.18.3.5.3.12.1.3
State of DVMRP base module
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), notpres(4)  

wfDvmrpBaseFullUpdateInterval 1.3.6.1.4.1.18.3.5.3.12.1.4
Full update interval. This value specifies, in seconds, how often routing messages containing complete routing tables are sent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 10..2000  

wfDvmrpBaseTriggeredUpdateInterval 1.3.6.1.4.1.18.3.5.3.12.1.5
Triggered update interval. This value specifies, in seconds, how often triggered routing messages are sent; this represents the minimum amount of time between these type of messages. Triggered updates are sent between full update; the timers restart when a full update is sent so this value should be less than the full update rate.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 5..1000  

wfDvmrpBaseLeafTimeout 1.3.6.1.4.1.18.3.5.3.12.1.6
Leaf timeout. This value specifies, in seconds, the virtual interface hold down timer.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 25..4000  

wfDvmrpBaseNeighborTimeout 1.3.6.1.4.1.18.3.5.3.12.1.7
Neighbor timeout. This value specifies, in seconds, how long a router neighbor is considered 'up' without confirmation.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 35..8000  

wfDvmrpBaseRouteExpirationTimeout 1.3.6.1.4.1.18.3.5.3.12.1.8
Route Expiration timeout. This value specifies, in seconds, how long a route is considered valid without confirmation; this represents the duration of time that this route will be used.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 20..4000  

wfDvmrpBaseGarbageTimeout 1.3.6.1.4.1.18.3.5.3.12.1.9
Garbage timeout. This value specifies, in seconds, how long a route exists without confirmation; this represents the duration of time that this route will be included in routing updates. This value must be greater than the route expiration timeout.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 40..8000  

wfDvmrpBaseEstimatedRoutes 1.3.6.1.4.1.18.3.5.3.12.1.10
Estimated number of routes, per slot. This is used for pre-allocating routing tables. Note that routes are kept on a per-source network basis, independent of multicast group. This number must include a route for every local network that has a CCT configured for multicasting.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 10..2147483647  

wfDvmrpBaseNeighborProbeInterval 1.3.6.1.4.1.18.3.5.3.12.1.11
Neighbor probe interval: how often to send a probe on VIFs
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 5..30  

wfDvmrpBaseRouteSwitchTimeout 1.3.6.1.4.1.18.3.5.3.12.1.12
Route switch timeout. How long to wait, without receiving a subsequent route update from the original neighbor, before switching to a different neighbor.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 20..2000  

wfDvmrpBaseActualRoutes 1.3.6.1.4.1.18.3.5.3.12.1.13
Count of number of entries currently in route table
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpBaseDebugLevel 1.3.6.1.4.1.18.3.5.3.12.1.14
Turn DVMRP log ON or OFF for DVMRP debuging messages The levels are: NO_DISPLAY_LOG 0x0001 - Reserved ROUTE_UPDATE_LOG 0x0002 - Displays all routing table events CACHE_ADD_LOG 0x0004 - Displays events relating to addition of cache entry by the cache gate CACHE_DELETE_LOG 0x0008 - Displays all events relating to deletion of cache entry CACHE_CHANGE_LOG 0x0010 - Displays all events relating to updates of cache entries CACHE_DATA_LOG 0x0020 - obsolete PRUNE_MSG_LOG 0x0040 - Display router received pruning related messages, including prunes, grafts, graft_acks, and neighbor reset PRUNE_XMIT_LOG 0x0080 - Display a messaged when a initial prune state is established for a (src, group). IGMP_COM_LOG 0x0100 - Display communication events between IGMP and DVMRP, events including some hosts joining a group, and all hosts leaving a group. DVMRP_XMIT_LOG 0x0200 - Display transmission events by the router, e.g, prune, grafts... CACHE_NO_GH_LOG 0x0400 - Display buffer forwarding to non-existing main or remote cache gate. CACHE_DBG_LOG 0x0800 - Display general debugging messaages MEM_DBG_LOG 0x1000 - Display dvmrp memory usage activities INTEROP_DBG_LOG 0x2000 - Display dvmrp mospf debug CACHE_BASE_ADD_LOG 0x4000 - Obsolete CACHE_VIF_ADD_LOG 0x8000 - Obsolete CACHE_BASE_DELETE_LOG 0x10000 - Obsolete CACHE_VIF_DELETE_LOG 0x20000 - Obsolete MTRACE_UPDATE_LOG 0x40000 - Displays mtrace update info NEIGHBOR_UPDATE_LOG 0x80000 - Display events relating to addition, deletion and update of neighbor's info MTM_INTERFACE_LOG 0x100000 - Display events relating to MTM-DVMRP interface, events as MTM inbound, outbound interact with DVMRP and entries deletion/addition. ROUTE_ADD_LOG 0x200000 - ROUTE_DEL_LOG 0x400000 - REMOTE_CACHE_ADD_LOG 0x800000 - Display addition event for the outgoing interface of (source, group) cache entry REMOTE_CACHE_DELETE_LOG 0x1000000 - Display deletion event for the outgoing interface of (source, group) cache entry RX_CONFLICT_ROUTE_INFO_LOG 0x2000000 - Display received conflict route information
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge 0..4294967295  

wfDvmrpBasePruningEnable 1.3.6.1.4.1.18.3.5.3.12.1.15
Enable or Disable Pruning functionality at the Base level
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDvmrpBaseFragmentMtuThreshold 1.3.6.1.4.1.18.3.5.3.12.1.16
the default value is the CSMACD_MTU, and the MINiMUN is X25_DDN_MTU. Both are taken from dp.h
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER 910..2147483647  

wfDvmrpBaseMaxRoutes 1.3.6.1.4.1.18.3.5.3.12.1.17
Max number of routes, per slot. This is used to limit the size of routing tables. Note that routes are kept on a per-source network basis, independent of multicast group. This number must include a route for every local network that has a CCT configured for multicasting.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

wfDvmrpBasePolicyEnable 1.3.6.1.4.1.18.3.5.3.12.1.18
Enable or Disable route policy functionality at the Base level
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDvmrpBaseHolddownEnable 1.3.6.1.4.1.18.3.5.3.12.1.19
Enable or Disable holddown of deleted routes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDvmrpCircuitEntryTable 1.3.6.1.4.1.18.3.5.3.12.2
Circuit virtual interfaces (aka physical VIFs)
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDvmrpCircuitEntry

wfDvmrpCircuitEntry 1.3.6.1.4.1.18.3.5.3.12.2.1
One instance of this object exists for every CCT that supports this feature. The instance ID for this object will be the circuit number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDvmrpCircuitEntry  

wfDvmrpCircuitCreate 1.3.6.1.4.1.18.3.5.3.12.2.1.1
Create or delete
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfDvmrpCircuitEnable 1.3.6.1.4.1.18.3.5.3.12.2.1.2
Enable or disable DVMRP on this circuit
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDvmrpCircuitState 1.3.6.1.4.1.18.3.5.3.12.2.1.3
The current state of the DVMRP interface. Invalid indicates an error in processing the configuration record.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), invalid(4), notpres(5)  

wfDvmrpCircuitCCT 1.3.6.1.4.1.18.3.5.3.12.2.1.4
This circuit number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpCircuitRouteEnable 1.3.6.1.4.1.18.3.5.3.12.2.1.5
Enable/disble this circuit for routing. If enabled, this circuit will be used to propogate routing information, information about this circuit will be incorporated into routing updates, and multicast datagrams will be forwarded 'in native mode' (e.g. as multicast datagrams) via this circuit. If disabled, this circuit exists only to support unicast tunnels; in this case, all other paramters are ignored.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDvmrpCircuitMetric 1.3.6.1.4.1.18.3.5.3.12.2.1.6
Metric. This value represents the cost of this interface; the cost of using this hop. This value must be smaller than the route infinity value
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..31  

wfDvmrpCircuitRouteThreshold 1.3.6.1.4.1.18.3.5.3.12.2.1.7
Threshold. This value can be used to filter out datagrams that are being forwarded to a neighboring router; if the IP TTL is not >= the threshold, the datagram is dropped by this router
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..254  

wfDvmrpCircuitInPkts 1.3.6.1.4.1.18.3.5.3.12.2.1.8
Number of datagrams received on this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpCircuitOutPkts 1.3.6.1.4.1.18.3.5.3.12.2.1.9
Number of datagrams send on this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpCircuitInRouteUpdates 1.3.6.1.4.1.18.3.5.3.12.2.1.10
Number of DVMRP route update messages received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpCircuitOutRouteUpdates 1.3.6.1.4.1.18.3.5.3.12.2.1.11
Number of DVMRP route update messages sent
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpCircuitInPktDiscards 1.3.6.1.4.1.18.3.5.3.12.2.1.12
Number of inbound datagrams discarded due to route not found
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpCircuitOutPktDiscards 1.3.6.1.4.1.18.3.5.3.12.2.1.13
Number of outbound datagrams discarded due to route not found
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpCircuitFwdCacheSize 1.3.6.1.4.1.18.3.5.3.12.2.1.14
Maximum number of entries allowed in the Forwarding table at one time. there is a Forwarding table per vif
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 32..512  

wfDvmrpCircuitFwdCacheTTL 1.3.6.1.4.1.18.3.5.3.12.2.1.15
The time_to_live for the Forwarding table entries in seconds .
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

wfDvmrpCircuitAdvertiseSelf 1.3.6.1.4.1.18.3.5.3.12.2.1.16
If enabled the router will advertise itself as one of the source net. If not enabled the router will not advertise itself as one of the source net.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDvmrpCircuitFwdCacheEntries 1.3.6.1.4.1.18.3.5.3.12.2.1.17
The most up to date number of entries in the forwarding cache
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpCircuitInPrunePkts 1.3.6.1.4.1.18.3.5.3.12.2.1.18
Number of PRUNE datagrams received on this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpCircuitOutPrunePkts 1.3.6.1.4.1.18.3.5.3.12.2.1.19
Number of PRUNE datagrams send on this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpCircuitInGraftPkts 1.3.6.1.4.1.18.3.5.3.12.2.1.20
Number of GRAFT datagrams received on this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpCircuitOutGraftPkts 1.3.6.1.4.1.18.3.5.3.12.2.1.21
Number of GRAFT datagrams send on this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpCircuitInGraftAckPkts 1.3.6.1.4.1.18.3.5.3.12.2.1.22
Number of GRAFT_ACK datagrams received on this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpCircuitOutGraftAckPkts 1.3.6.1.4.1.18.3.5.3.12.2.1.23
Number of GRAFT_ACK datagrams send on this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpCircuitDefaultRouteSupply 1.3.6.1.4.1.18.3.5.3.12.2.1.24
enabled : Send the default route, 0.0.0.0 if learned, form this interface. disabled: no default route is sent from this interface. generate: generate default route, 0.0.0.0 from this interface.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), generate(3)  

wfDvmrpCircuitDefaultRouteListen 1.3.6.1.4.1.18.3.5.3.12.2.1.25
Receive the default route, 0.0.0.0 on this interface
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDvmrpCircuitReportDependProbe 1.3.6.1.4.1.18.3.5.3.12.2.1.26
This is to control accepting the route report. According to the protocol, dvmrp should send probe packet before sending the route report packet to the neighbors. But some vendor implementation did not send probes before sending reports. Enable: only process the routes from the neighbor sending probes. Disable: No Dependency (no restriction).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDvmrpCircuitPruneLifeTime 1.3.6.1.4.1.18.3.5.3.12.2.1.27
The life time of the prune message the router sends to its neighbor in seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

wfDvmrpCircuitAcceptAggregateRoutes 1.3.6.1.4.1.18.3.5.3.12.2.1.28
Count of number of routes received have been aggregated to the specific aggregate route currently in route table for this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpCircuitAnnounceAggregatedRoutes 1.3.6.1.4.1.18.3.5.3.12.2.1.29
Count of number of routes have been aggregated to the specific aggregate route for advertisement currently in route table for this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpTunnelEntryTable 1.3.6.1.4.1.18.3.5.3.12.3
Tunnel virtual interfaces
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDvmrpTunnelEntry

wfDvmrpTunnelEntry 1.3.6.1.4.1.18.3.5.3.12.3.1
This object is used to specify the set of 'multicast tunnels', unicast pipes that are used to send IP multicast datagrams to remote network multicast routers via intermediate routers that may not support this style of IP multicasting. One instance of this object exists for every separate tunnel destination. The instance identifier is the IP address of the remote router neighbor and the local circuit number.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDvmrpTunnelEntry  

wfDvmrpTunnelCreate 1.3.6.1.4.1.18.3.5.3.12.3.1.1
create/delete
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER created(1), deleted(2)  

wfDvmrpTunnelEnable 1.3.6.1.4.1.18.3.5.3.12.3.1.2
enable/disable this tunnel interface
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDvmrpTunnelState 1.3.6.1.4.1.18.3.5.3.12.3.1.3
The current state of the DVMRP tunnel interface. Invalid indicates an error in processing the configuration record.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), init(3), invalid(4), notpres(5)  

wfDvmrpTunnelCCT 1.3.6.1.4.1.18.3.5.3.12.3.1.4
The multicast circuit associated with this tunnel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpTunnelRemoteRouterIpAddress 1.3.6.1.4.1.18.3.5.3.12.3.1.5
(unicast) IP address of remote network router neighbor.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfDvmrpTunnelEncapsMode 1.3.6.1.4.1.18.3.5.3.12.3.1.6
Will these tunnelled datagrams be encapsulated within an IP datagram, or will they be loosely encapsulated using the LSSR option (for the latter, refer to RFC 1075; this is needed for backward compatibility)
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER ip-in-ip(1), lssr(2)  

wfDvmrpTunnelMetric 1.3.6.1.4.1.18.3.5.3.12.3.1.7
Cost of using this tunnel
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..31  

wfDvmrpTunnelThreshold 1.3.6.1.4.1.18.3.5.3.12.3.1.8
Threshold for forwarding through this tunnel; if TTL < threshold, the datagram is dropped.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 1..254  

wfDvmrpTunnelInPkts 1.3.6.1.4.1.18.3.5.3.12.3.1.9
Number of datagrams received on this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpTunnelOutPkts 1.3.6.1.4.1.18.3.5.3.12.3.1.10
Number of datagrams send on this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpTunnelInRouteUpdates 1.3.6.1.4.1.18.3.5.3.12.3.1.11
Number of DVMRP route update messages received
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpTunnelOutRouteUpdates 1.3.6.1.4.1.18.3.5.3.12.3.1.12
Number of DVMRP route update messages sent
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpTunnelInPktDiscards 1.3.6.1.4.1.18.3.5.3.12.3.1.13
Number of inbound datagrams discarded due to route not found or due to invalid inner address (dest address != multicast)
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpTunnelOutPktDiscards 1.3.6.1.4.1.18.3.5.3.12.3.1.14
Number of outbound datagrams discarded due to route not found
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpTunnelLocalRouterIpAddress 1.3.6.1.4.1.18.3.5.3.12.3.1.15
(unicast) IP address of local network router. To support multinet.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfDvmrpTunnelFwdCacheSize 1.3.6.1.4.1.18.3.5.3.12.3.1.16
Maximum number of entries allowed in the Forwarding table at one time. there is a Forwarding table per vif
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 32..512  

wfDvmrpTunnelFwdCacheTTL 1.3.6.1.4.1.18.3.5.3.12.3.1.17
The time_to_live for the Forwarding table entries in seconds .
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

wfDvmrpTunnelFwdCacheEntries 1.3.6.1.4.1.18.3.5.3.12.3.1.18
The most up to date number of entries in the forwarding cache
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpTunnelInPrunePkts 1.3.6.1.4.1.18.3.5.3.12.3.1.19
Number of PRUNE datagrams received on this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpTunnelOutPrunePkts 1.3.6.1.4.1.18.3.5.3.12.3.1.20
Number of PRUNE datagrams send on this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpTunnelInGraftPkts 1.3.6.1.4.1.18.3.5.3.12.3.1.21
Number of GRAFT datagrams received on this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpTunnelOutGraftPkts 1.3.6.1.4.1.18.3.5.3.12.3.1.22
Number of GRAFT datagrams send on this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpTunnelInGraftAckPkts 1.3.6.1.4.1.18.3.5.3.12.3.1.23
Number of GRAFT_ACK datagrams received on this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpTunnelOutGraftAckPkts 1.3.6.1.4.1.18.3.5.3.12.3.1.24
Number of GRAFT_ACK datagrams send on this interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpTunnelDefaultRouteSupply 1.3.6.1.4.1.18.3.5.3.12.3.1.25
Send the default route, 0.0.0.0 on this interface
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2), generate(3)  

wfDvmrpTunnelDefaultRouteListen 1.3.6.1.4.1.18.3.5.3.12.3.1.26
Receive the default route, 0.0.0.0 on this interface
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDvmrpTunnelCtrlMsgMode 1.3.6.1.4.1.18.3.5.3.12.3.1.27
Dvmrp tunneling control messages encapsulated type. noencaps is the mode that control messages are sent in regular igmp packets with ip protocol type set to IP_PROTOCOL_IGMP. encaps is the mode that control messages are encapsed inside ip packets with ip protocol type set to IP_PROTOCOL_IPINIP. All DVMRP messages sent across tunnels will be encapsulated in the same way as data packets in this mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER native(1), ip-in-ip(2)  

wfDvmrpTunnelReportDependProbe 1.3.6.1.4.1.18.3.5.3.12.3.1.28
This is to control accepting the route report. According to the protocol, dvmrp should send probe packet before sending the route report packet to the neighbors. But some vendor implementations do not send probes before sending reports. Enable: only process the routes from the neighbor sending probes. Disable: No Dependency (no restriction).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(1), disabled(2)  

wfDvmrpTunnelPruneLifeTime 1.3.6.1.4.1.18.3.5.3.12.3.1.29
The life time of the prune message the router send to its neighbor in seconds.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..86400  

wfDvmrpTunnelAcceptAggregateRoutes 1.3.6.1.4.1.18.3.5.3.12.3.1.30
Count of number of routes received have been aggregated to the specific aggregate route currently in route table for this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpTunnelAnnounceAggregatedRoutes 1.3.6.1.4.1.18.3.5.3.12.3.1.31
Count of number of routes have been aggregated to the specific aggregate route for advertisement currently in route table for this interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpRouteEntryTable 1.3.6.1.4.1.18.3.5.3.12.4
MIB proxy: main DVMRP routing table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDvmrpRouteEntry

wfDvmrpRouteEntry 1.3.6.1.4.1.18.3.5.3.12.4.1
Supported by mib proxy. One entry exists for each active route.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDvmrpRouteEntry  

wfDvmrpRouteSourceNetwork 1.3.6.1.4.1.18.3.5.3.12.4.1.1
A source of multicast datagrams
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfDvmrpRouteSourceMask 1.3.6.1.4.1.18.3.5.3.12.4.1.2
Mask for the specified source network
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfDvmrpRouteNextHopRouter 1.3.6.1.4.1.18.3.5.3.12.4.1.3
Next hop multicast router to the specified source network; we consider this neighboring router to be on the shortest path to the source. Note that this neighboring router may be a tunnel endpoint.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfDvmrpRouteNextHopInterfaceCCT 1.3.6.1.4.1.18.3.5.3.12.4.1.4
Next hop interface (CCT) to the specified source router; we consider this interface to be on the shortest path to the source.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpRouteNextHopInterfaceTunnelId 1.3.6.1.4.1.18.3.5.3.12.4.1.5
Next hop interface (tunnel id) to the specified source router; we consider this interface to be on the shortest path to the source.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfDvmrpRouteNextHopInterfaceLocalTunnelId 1.3.6.1.4.1.18.3.5.3.12.4.1.6
Next hop interface (local tunnel id) to the specified source router; we consider this interface to be on the shortest path to the source.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfDvmrpRouteTimer 1.3.6.1.4.1.18.3.5.3.12.4.1.7
route timer
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpRouteState 1.3.6.1.4.1.18.3.5.3.12.4.1.8
Set of flags indicating state of entry. Note that the router uses this field as a bit mask. 0x8000 Network is local to this router 0x4000 Route is being timed 0x2000 Route is garbaged
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpRouteMetric 1.3.6.1.4.1.18.3.5.3.12.4.1.9
current route metric
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpRouteProtocol 1.3.6.1.4.1.18.3.5.3.12.4.1.10
current route protocol dvmrp (2) or mospf (4) or internal (6) which is the route from unicast and incoming interface no i dvmrp configure, if dvmrp is configured then the protocol will be set to 2, see wfIgmpRoutingProtocol
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpRouteType 1.3.6.1.4.1.18.3.5.3.12.4.1.11
The orginal route source from. If it is from pure dvmrp route (0x0001) unicast best route (0x0002) unciast route but has dvmrp interface (0x0003) ospf(0x0004) ospf best route (0x0006) ospf ase route (0x0008)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpRouteAggregatedType 1.3.6.1.4.1.18.3.5.3.12.4.1.12
Route Aggregated types : 0 - normal route 1 - inbound aggregated route 2 - outbound aggregated route 4 - inbound aggregate route 8 - outbound aggregate route
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpRouteInterfaceEntryTable 1.3.6.1.4.1.18.3.5.3.12.5
MIB proxy: DVMRP VIF routing table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDvmrpRouteInterfaceEntry

wfDvmrpRouteInterfaceEntry 1.3.6.1.4.1.18.3.5.3.12.5.1
Supported by mib proxy. One entry exists for each virtual interface on an active route. It is associated with a route via the source network/ net mask fields. The instance ID includes tunnel ID, which is 0 for non-tunnel interfaces.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDvmrpRouteInterfaceEntry  

wfDvmrpRouteInterfaceSourceNetwork 1.3.6.1.4.1.18.3.5.3.12.5.1.1
A source of multicast datagrams
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfDvmrpRouteInterfaceSourceMask 1.3.6.1.4.1.18.3.5.3.12.5.1.2
Mask for the specified source network
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfDvmrpRouteInterfaceNextHopInterfaceCCT 1.3.6.1.4.1.18.3.5.3.12.5.1.3
circuit number with which this route is associated
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpRouteInterfaceNextHopInterfaceLocalTunnelId 1.3.6.1.4.1.18.3.5.3.12.5.1.4
Tunnel ID for tunnelled interfaces. This value is zero for non-tunnelled interfaces, otherwise it contains the local IP address of the tunnel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfDvmrpRouteInterfaceNextHopInterfaceTunnelId 1.3.6.1.4.1.18.3.5.3.12.5.1.5
Tunnel ID for tunnelled interfaces. This value is zero for non-tunnelled interfaces, otherwise it contains the remote IP address of the tunnel.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfDvmrpRouteInterfaceState 1.3.6.1.4.1.18.3.5.3.12.5.1.6
state of interface for this route. Note that the router uses this field as a bit mask. 0x8000 - interface is leaf 0x4000 - interface is child 0x2000 - interface is in hold-down state 0x1000 - interface has loop neighbor for this route
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpRouteInterfaceDominantRouter 1.3.6.1.4.1.18.3.5.3.12.5.1.7
dominant router address for virtual interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfDvmrpRouteInterfaceSubordinateRouter 1.3.6.1.4.1.18.3.5.3.12.5.1.8
subordinate router address for virtual interface
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfDvmrpRouteInterfaceHoldDownTimer 1.3.6.1.4.1.18.3.5.3.12.5.1.9
Current value of hold down timer, used to determine if interface is for leaf or non-leaf network. Non-leaf network means that a local network router considers us to be in the shortest path to the source (they have sent us a route update with metric >= infinity).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpRouteInterfaceSPInDiscards 1.3.6.1.4.1.18.3.5.3.12.5.1.10
Count of inbound packets discarded because interface not on shortest path
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpRouteInterfaceSPOutDiscards 1.3.6.1.4.1.18.3.5.3.12.5.1.11
Count of outbound packets discarded because interface not on shortest path
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpRouteInterfaceThresholdOutDiscards 1.3.6.1.4.1.18.3.5.3.12.5.1.12
Count of outbound packets discarded because of threshold
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpRouteInterfaceInSuccessfulPkts 1.3.6.1.4.1.18.3.5.3.12.5.1.13
Count of inbound packets accepted for forwarding
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpRouteInterfaceOutSuccessfulPkts 1.3.6.1.4.1.18.3.5.3.12.5.1.14
Count of outbound packets accepted for forwarding
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter  

wfDvmrpRouteInterfaceParentCCT 1.3.6.1.4.1.18.3.5.3.12.5.1.15
circuit number with which this route is associated;parent VIF
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpRouteInterfaceParentLocalTunnelId 1.3.6.1.4.1.18.3.5.3.12.5.1.16
Tunnel ID for tunnelled interfaces. This value is zero for non-tunnelled interfaces, otherwise it contains the local IP address of the tunnel; parent VIF.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfDvmrpRouteInterfaceParentTunnelId 1.3.6.1.4.1.18.3.5.3.12.5.1.17
Tunnel ID for tunnelled interfaces. This value is zero for non-tunnelled interfaces, otherwise it contains the remote IP address of the tunnel; parent VIF.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfDvmrpNeighboringRouterEntryTable 1.3.6.1.4.1.18.3.5.3.12.6
MIB proxy: DVMRP neighbor table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WfDvmrpNeighboringRouterEntry

wfDvmrpNeighboringRouterEntry 1.3.6.1.4.1.18.3.5.3.12.6.1
This entry is used to indentify the known neighboring routers for a circuit. This object will be indentified by circuit number, tunnel id (to identify local interface), and the IP address of the neighbor.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  WfDvmrpNeighboringRouterEntry  

wfDvmrpNeighboringRouterCCT 1.3.6.1.4.1.18.3.5.3.12.6.1.1
Local circuit number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpNeighboringRouterLocalTunnelId 1.3.6.1.4.1.18.3.5.3.12.6.1.2
Tunnel Id for interface. This value is zero for non- tunnelled interfaces, otherwise it contains the IP address of the local tunnel endpoint.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfDvmrpNeighboringRouterTunnelId 1.3.6.1.4.1.18.3.5.3.12.6.1.3
Tunnel Id for interface. This value is zero for non- tunnelled interfaces, otherwise it contains the IP address of the remote tunnel endpoint.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfDvmrpNeighboringRouterIpAddr 1.3.6.1.4.1.18.3.5.3.12.6.1.4
IP address of neighboring router
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

wfDvmrpNeighboringRouterState 1.3.6.1.4.1.18.3.5.3.12.6.1.5
State of neighbor. The router uses this as a bit mask. 0x8000 - Neighbor is being timed
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpNeighboringRouterTimer 1.3.6.1.4.1.18.3.5.3.12.6.1.6
Current value of neighbor timer
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpNeighboringRouterGenId 1.3.6.1.4.1.18.3.5.3.12.6.1.7
The neighboring router's generation identifier.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

wfDvmrpNeighboringRouterMajorVersion 1.3.6.1.4.1.18.3.5.3.12.6.1.8
The neighboring router's major DVMRP version number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

wfDvmrpNeighboringRouterMinorVersion 1.3.6.1.4.1.18.3.5.3.12.6.1.9
The neighboring router's minor DVMRP version number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

wfDvmrpNeighboringRouterCapabilities 1.3.6.1.4.1.18.3.5.3.12.6.1.10
This object describes the neighboring router's capabilities. The leaf bit indicates that the neighbor has only one interface with neighbors. The prune bit indicates that the neighbor supports pruning. The generationID bit indicates that the neighbor sends its generationID in Probe messages. The mtrace bit indicates that the neighbor can handle mtrace requests.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER