Wellfleet-DS3E3-MIB

File: Wellfleet-DS3E3-MIB.mib (14525 bytes)

Imported modules

RFC1155-SMI

RFC-1212

Wellfleet-COMMON-MIB

Imported symbols

TimeTicks

OBJECT-TYPE

wfDsx3Group

Defined Types

WfDs3E3ConfigEntry
SEQUENCE
	wfDs3E3ConfigDelete	INTEGER
	wfDs3E3ConfigDisable	INTEGER
	wfDs3E3ConfigState	INTEGER
	wfDs3E3ConfigLastChange	TimeTicks
	wfDs3E3ConfigLineIndex	INTEGER
	wfDs3E3ConfigIfIndex	INTEGER
	wfDs3E3ConfigLineType	INTEGER
	wfDs3E3ConfigLineCoding	INTEGER
	wfDs3E3ConfigLoopbackConfig	INTEGER
	wfDs3E3ConfigLineStatus	INTEGER
	wfDs3E3ConfigPrimaryClockSource	INTEGER
	wfDs3E3ConfigSecondaryClockSource	INTEGER
	wfDs3E3ConfigMtu	INTEGER
	wfDs3E3ConfigLineBuildOut	INTEGER
	wfDs3E3ConfigCurrentClock	INTEGER
	wfDs3E3ConfigExtClockOperational	INTEGER
	wfDs3E3ConfigSetupAlarmThreshold	INTEGER
	wfDs3E3ConfigClearAlarmThreshold	INTEGER
	wfDs3E3ConfigLoopbackState	INTEGER
	wfDs3E3ConfigSendCode	INTEGER

WfDs3E3ActionEntry
SEQUENCE
	wfDs3E3ActionPortLineNumber	INTEGER
	wfDs3E3ActionSendFeacLoopCode	INTEGER
	wfDs3E3ActionSendFeacDs1LoopUpCode	INTEGER
	wfDs3E3ActionSendFeacDs1LoopDownCode	INTEGER
	wfDs3E3ActionClearCurrentStats	INTEGER
	wfDs3E3ActionClearFarEndCurrentStats	INTEGER
	wfDs3E3ActionClearDayCurrentStats	INTEGER
	wfDs3E3ActionClearFarEndDayCurrentStats	INTEGER
	wfDs3E3ActionClearIntervalStats	INTEGER
	wfDs3E3ActionClearFarEndIntervalStats	INTEGER

Defined Values

wfDs3E3ConfigTable		1.3.6.1.4.1.18.3.4.26.10
The DS3/E3 Configuration table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfDs3E3ConfigEntry

wfDs3E3ConfigEntry		1.3.6.1.4.1.18.3.4.26.10.1
per circuit DS3/E3 configuration objects; wfDs3E3ConfigLineIndex corresponds to Wellfleet circuit number
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfDs3E3ConfigEntry

wfDs3E3ConfigDelete		1.3.6.1.4.1.18.3.4.26.10.1.1
Create/Delete parameter
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	created(1), deleted(2)

wfDs3E3ConfigDisable		1.3.6.1.4.1.18.3.4.26.10.1.2
Enable/Disable parameter
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	enabled(1), disabled(2)

wfDs3E3ConfigState		1.3.6.1.4.1.18.3.4.26.10.1.3
State of the DS3 Port.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	up(1), down(2), los(3), lof(4), raif(5), ais(6), loopback(7), notpresent(20)

wfDs3E3ConfigLastChange		1.3.6.1.4.1.18.3.4.26.10.1.4
The value of sysUpTime at the time the interface entered its current operational state.
Status: mandatory	Access: read-only
OBJECT-TYPE
	TimeTicks

wfDs3E3ConfigLineIndex		1.3.6.1.4.1.18.3.4.26.10.1.5
this corresponds to the Wellfleet circuit number
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	1..65535

wfDs3E3ConfigIfIndex		1.3.6.1.4.1.18.3.4.26.10.1.6
this is value of ifIndex from the Interfaces table of MIB II (RFC 1213).
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfDs3E3ConfigLineType		1.3.6.1.4.1.18.3.4.26.10.1.7
the variety of DS3/E3 application implementing this circuit
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	ds3other(1), ds3m23(2), ds3syntran(3), ds3cbitparity(4), ds3clearchannel(5), e3other(6), e3framed(7), e3plcp(8), autodetect(9)

wfDs3E3ConfigLineCoding		1.3.6.1.4.1.18.3.4.26.10.1.8
the variety of Zero Code Suppression used on the link
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	other(1), b3zs(2), hdb3(3)

wfDs3E3ConfigLoopbackConfig		1.3.6.1.4.1.18.3.4.26.10.1.9
the loopback configuration of the DS3/E3 interface
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	noloop(1), payloadloop(2), lineloop(3)

wfDs3E3ConfigLineStatus		1.3.6.1.4.1.18.3.4.26.10.1.10
the status of the DS3/E3 line
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noalarm(1), rcrai(2), txrai(4), rcais(8), txais(16), lof(32), los(64), loopback(128), rctestcode(256), otherfailure(512)

wfDs3E3ConfigPrimaryClockSource		1.3.6.1.4.1.18.3.4.26.10.1.11
Selects the Primary source of the Tx Clock for the DS3/E3 interface
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	internal(1), external(2), loop(3)

wfDs3E3ConfigSecondaryClockSource		1.3.6.1.4.1.18.3.4.26.10.1.12
Selects the Secondary source of the Tx Clock for the DS3/E3 interface
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	internal(1), external(2), loop(3)

wfDs3E3ConfigMtu		1.3.6.1.4.1.18.3.4.26.10.1.13
MTU parameter for all channels on DS3 .
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	3..4608

wfDs3E3ConfigLineBuildOut		1.3.6.1.4.1.18.3.4.26.10.1.14
Set according to cable length, short (less than 225 feet) or long (greater than 225 feet).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	long(1), short(2)

wfDs3E3ConfigCurrentClock		1.3.6.1.4.1.18.3.4.26.10.1.15
Indicates the clock source currently in use by the DS1
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	internal(1), external(2), loop(3)

wfDs3E3ConfigExtClockOperational		1.3.6.1.4.1.18.3.4.26.10.1.16
Indicates whether the External clock is operational
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	present(1), notpresent(2)

wfDs3E3ConfigSetupAlarmThreshold		1.3.6.1.4.1.18.3.4.26.10.1.17
Specifies setup time for performance failure conditions, in seconds. When a performance defect is present for greater than the time specified by this parameter a performance failure is registered and a message is logged.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	2..10

wfDs3E3ConfigClearAlarmThreshold		1.3.6.1.4.1.18.3.4.26.10.1.18
Specifies clear time for performance failure conditions, in seconds. When a performance failure condition has been cleared for greater than the time specified by this parameter then the failure cleared condition is registered and a message is logged.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	2..10

wfDs3E3ConfigLoopbackState		1.3.6.1.4.1.18.3.4.26.10.1.19
Indicates the current loopback state of this interface. The interface can be in one the following states: Line Loopback Payload Loopback no loopback Loopback modes can be initiated by either of two methods: Manager requested Loopback is initiated by the Manager of this device. Network requested Loopback is initiated by this interface receiving an in-band request on the network from the far end device.
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	noloop(1), mgrreqlineloop(2), mgrreqpayloadloop(3), netreqlineloop(4), netreqpayloadloop(5)

wfDs3E3ConfigSendCode		1.3.6.1.4.1.18.3.4.26.10.1.20
This variable is currently read-only and it indicates what type of code has been sent across the DS3 interface by the device. The values mean: SENDNOCODE - sending looped or normal data SENDLINECODE - sending a request for a line loopback SENDPAYLOADCODE - sending a request for a payload loopback SENDDS1LOOPCODE - sending a request for a DS1 loopback
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER	sendnocode(1), sendlinecode(2), sendpayloadcode(3), sendds1loopcode(4)

wfDs3E3ActionTable		1.3.6.1.4.1.18.3.4.26.17
DS3E3 configuration Action record - write only Configuration parameters
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		WfDs3E3ActionEntry

wfDs3E3ActionEntry		1.3.6.1.4.1.18.3.4.26.17.1
An entry in the DS3E3 Config table
Status: mandatory	Access: not-accessible
OBJECT-TYPE
	WfDs3E3ActionEntry

wfDs3E3ActionPortLineNumber		1.3.6.1.4.1.18.3.4.26.17.1.1
Instance ID LineNumber, filled in by driver
Status: mandatory	Access: read-only
OBJECT-TYPE
	INTEGER

wfDs3E3ActionSendFeacLoopCode		1.3.6.1.4.1.18.3.4.26.17.1.2
Selects a Far End Alarm and Control Channel code to be sent to the remote end.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	lineloop(1), deactivatell(2), payloadloop(3), deactivatepl(4), noaction(21)

wfDs3E3ActionSendFeacDs1LoopUpCode		1.3.6.1.4.1.18.3.4.26.17.1.3
Selects Loop Up code to be sent to the remote end for a DS1. Value passed through this attribute is the DS1 Port number (1 through 28).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	noaction(29)

wfDs3E3ActionSendFeacDs1LoopDownCode		1.3.6.1.4.1.18.3.4.26.17.1.4
Selects Loop Down code to be sent to the remote end for a DS1. Value passed through this attribute is the DS1 Port number (1 through 28).
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	noaction(29)

wfDs3E3ActionClearCurrentStats		1.3.6.1.4.1.18.3.4.26.17.1.5
Clears this port's Current 15 minute Statistics.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	clrStats(1), noaction(2)

wfDs3E3ActionClearFarEndCurrentStats		1.3.6.1.4.1.18.3.4.26.17.1.6
Clears this port's Far End, Current 15 minute Statistics.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	clrStats(1), noaction(2)

wfDs3E3ActionClearDayCurrentStats		1.3.6.1.4.1.18.3.4.26.17.1.7
Clears this port's Current Day Statistics.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	clrStats(1), noaction(2)

wfDs3E3ActionClearFarEndDayCurrentStats		1.3.6.1.4.1.18.3.4.26.17.1.8
Clears this port's Far End, Current Day Statistics.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	clrStats(1), noaction(2)

wfDs3E3ActionClearIntervalStats		1.3.6.1.4.1.18.3.4.26.17.1.9
Clears All Interval Statistics (15 minute and day) of this port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	clrStats(1), noaction(2)

wfDs3E3ActionClearFarEndIntervalStats		1.3.6.1.4.1.18.3.4.26.17.1.10
Clears All Far End Interval Statistics (15 minute and day) of this port.
Status: mandatory	Access: read-write
OBJECT-TYPE
	INTEGER	clrStats(1), noaction(2)