WWP-LEOS-RSVPTE-MIB
File:
WWP-LEOS-RSVPTE-MIB.mib (13855 bytes)
Imported modules
Imported symbols
Defined Types
AdvertisedLabel |
|
Advertised Label |
TEXTUAL-CONVENTION |
|
|
|
|
INTEGER |
implicitnull(1), nonreserved(99) |
|
WwpLeosRsvpteIfEntry |
|
SEQUENCE |
|
|
|
|
wwpLeosRsvpteIfIndex |
INTEGER |
|
|
wwpLeosRsvpteIfName |
DisplayString |
|
|
wwpLeosRsvpteIfIpAddr |
IpAddress |
|
|
wwpLeosRsvpteIfMtu |
INTEGER |
|
|
wwpLeosRsvpteIfAdminStatus |
INTEGER |
|
|
wwpLeosRsvpteIfOperStatus |
INTEGER |
|
|
wwpLeosRsvpteIfHelloInterval |
Unsigned32 |
|
|
wwpLeosRsvpteIfHelloTolerance |
Unsigned32 |
|
|
wwpLeosRsvpteIfAdvertisedLabel |
AdvertisedLabel |
|
Defined Values
wwpLeosRsvpteMIB |
1.3.6.1.4.1.6141.2.60.30 |
Added new objects wwpLeosRsvpteIfHelloInterval,wwpLeosRsvpteIfHelloTolerance,
wwpLeosRsvpteIfAdvertisedLabel. |
MODULE-IDENTITY |
|
|
|
wwpLeosRsvpteAdminStatus |
1.3.6.1.4.1.6141.2.60.30.1.1.1 |
The desired administrative state of RSVP-TE. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enable(1), disable(2) |
|
wwpLeosRsvpteOperStatus |
1.3.6.1.4.1.6141.2.60.30.1.1.2 |
The current operational state of RSVP-TE. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
up(1), down(2), goingUp(3), goingDown(4), actFailed(5) |
|
wwpLeosRsvpteRetryInterval |
1.3.6.1.4.1.6141.2.60.30.1.1.3 |
The persistent tunnel retry interval.
This is the interval between the first failure of a persistent
tunnel and the first attempt to re-establish the tunnel.
This cannot be changed while admin status is enable or oper status is up |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
3..65 |
|
wwpLeosRsvpteRetryInfiniteState |
1.3.6.1.4.1.6141.2.60.30.1.1.4 |
The persistent tunnel retry infinity.
This is the State which when on will trigger RSVP-TE to try to restore the tunnels
infinite times. This object can only be set if RSVP-TE is globally disabled. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
on(1), off(2) |
|
wwpLeosRsvpteRetryMax |
1.3.6.1.4.1.6141.2.60.30.1.1.5 |
The maximum number of retry attempts that will be made before a
persistent tunnel is deemed inoperable. Once in this state,
a management agent should set mplsTunnelAdminStatus to 'up' to
attempt to reestablish the tunnel.
This field is not used when wwpLeosRsvpteRetryInfiniteState is on |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..255 |
|
wwpLeosRsvpteRefreshInterval |
1.3.6.1.4.1.6141.2.60.30.1.1.6 |
This RSVP-TE value, R, which is used to set the average
interval between refresh path and resv messages. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
wwpLeosRsvpteRefreshMultiple |
1.3.6.1.4.1.6141.2.60.30.1.1.7 |
The RSVP-TE value, K, which is the number of unresponded Path
or Resv refresh attempts which must be made, spaced by
the refresh interval before the state is deemed to have
timed out. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
1..214783647 |
|
wwpLeosRsvpteRfrshSlewDenom |
1.3.6.1.4.1.6141.2.60.30.1.1.8 |
The denominator of the fraction, SlewMax, which is the
maximum allowable increase in the refresh interval, R, to
prevent state timeout while changing R. R is increased by
this fraction until it reaches the new desired value. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
1..214783647 |
|
wwpLeosRsvpteRfrshSlewNumerator |
1.3.6.1.4.1.6141.2.60.30.1.1.9 |
The numerator of the fraction, SlewMax, which is the maximum
allowable increase in the refresh interval, R, to prevent
state timeout while changing R. R is increased by this
fraction until it reaches the new desired value. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
1..214783647 |
|
wwpLeosRsvpteBlockadeMultiple |
1.3.6.1.4.1.6141.2.60.30.1.1.10 |
The RSVP-TE value, Kb, which is the number of refresh timeout
periods after which blockade state is deleted. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
1..214783647 |
|
wwpLeosRsvpteLSPSetupPriority |
1.3.6.1.4.1.6141.2.60.30.1.1.11 |
The setup priority to apply to LSPs which are not
signalling this parameter. 0 represents the highest
priority, 7 the lowest. The value of this object must be
numerically more or equal (so lower or equal priority)
than the value of the holding priority object. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
0..7 |
|
wwpLeosRsvpteLSPHoldingPriority |
1.3.6.1.4.1.6141.2.60.30.1.1.12 |
The holding priority to apply to LSPs which are not
signalling this parameter. 0 represents the highest
priority, 7 the lowest. The value of this object must be
numerically less or equal (so higher or equal priority)
than the value of the holding priority object. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
0..7 |
|
wwpLeosRsvpteUseHopByHop |
1.3.6.1.4.1.6141.2.60.30.1.1.13 |
A flag to indicate that RSVP-TE should use the hop by hop
addressing scheme for PATH and PATH-TEAR messages it
sends. If set then the IP addresses used in the IP header
of PATH messages forwarded by RSVP-TE set source as the
local outgoing interface IP address, and destination as
the next hop router IP address. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
wwpLeosRsvpteRestartCapable |
1.3.6.1.4.1.6141.2.60.30.1.1.14 |
A flag to indicate whether the local node should advertise
itself as restart capable. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
TruthValue |
|
|
wwpLeosRsvpteRestartTime |
1.3.6.1.4.1.6141.2.60.30.1.1.15 |
The time in milliseconds that the local node takes to
restart RSVP-TE and the communication channel used for
RSVP-TE communication. This is advertised to neighbors in
the Restart_Cap object in Hello messages.
Only used if wwpLeosRsvpteRestartCapable is set to true. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
wwpLeosRsvpteRecoveryTime |
1.3.6.1.4.1.6141.2.60.30.1.1.16 |
The period of time in milliseconds that the local node
would like neighbors to take to resyncronize RSVP-TE and
MPLS forwarding information after the re-establishment of
Hello connectivity. This is advertised to neighbors in
the Restart_Cap object in Hello messages.
A value of zero indicates that the node does not support
resynchronization following failure of the local node.
A value of 0xFFFFFFFF indicates an infinite recovery time.
Only used if wwpLeosRsvpteRestartCapable is set to true. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
|
|
wwpLeosRsvpteMinPeerRestart |
1.3.6.1.4.1.6141.2.60.30.1.1.17 |
The mininum period of time in milliseconds that RSVP-TE
should wait for a restart capable neighbor to regain
Hello connectivity before invoking procedures related to
communication loss.
RSVP-TE will wait for the maximum of this time and the
restart_time advertised in the RESTART_CAP object in Hello
messages from the neighbor. |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
wwpLeosRsvpteIfEntry |
1.3.6.1.4.1.6141.2.60.30.1.2.1.1 |
WWP Descr. |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
WwpLeosRsvpteIfEntry |
|
|
wwpLeosRsvpteIfIndex |
1.3.6.1.4.1.6141.2.60.30.1.2.1.1.2 |
Interface Index |
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1..4096 |
|
wwpLeosRsvpteIfMtu |
1.3.6.1.4.1.6141.2.60.30.1.2.1.1.4 |
RSVP-TE Interface MTU |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
1500..9216 |
|
wwpLeosRsvpteIfAdminStatus |
1.3.6.1.4.1.6141.2.60.30.1.2.1.1.5 |
Desired RSVP-TE status on this Interface |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
INTEGER |
enable(1), disable(2) |
|
wwpLeosRsvpteIfOperStatus |
1.3.6.1.4.1.6141.2.60.30.1.2.1.1.6 |
RSVP-TE Operational Status on this Interface |
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
up(1), down(2) |
|
wwpLeosRsvpteIfHelloTolerance |
1.3.6.1.4.1.6141.2.60.30.1.2.1.1.8 |
RSVP-TE hello tolerance defines number of hello interval which may pass without receiving a
successful Hello message from a partner before the Hello session times out. |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
Unsigned32 |
0..10 |
|
wwpLeosRsvpteIfAdvertisedLabel |
1.3.6.1.4.1.6141.2.60.30.1.2.1.1.9 |
This attribute decides what kind of a Label will be advertised by RSVP-TE for a
Label Request received on this L3 Interface |
Status: current |
Access: read-write |
OBJECT-TYPE |
|
|
|
|
AdvertisedLabel |
|
|