WS-SW-AUTHENTICATEDNTP-MIB

File: WS-SW-AUTHENTICATEDNTP-MIB.mib (31071 bytes)

Imported modules

SNMPv2-CONF SNMPv2-SMI SNMPv2-TC
WS-SW-SMI

Imported symbols

OBJECT-GROUP MODULE-COMPLIANCE Integer32
Unsigned32 OBJECT-TYPE MODULE-IDENTITY
TruthValue DisplayString RowStatus
TEXTUAL-CONVENTION wsSwNtp

Defined Types

NTPLeapIndicator  
This is a two-bit code warning of an impending leap second to be inserted in the NTP timescale. The bits are set before 23:59 on the day of insertion and reset after 00:00 on the following day. This causes the number of seconds (rollover interval) in the day of insertion to be increased or decreased by one. The two bits are coded as below, 00, no warning 01, last minute has 61 seconds 10, last minute has 59 seconds 11, alarm condition (clock not synchronized)
TEXTUAL-CONVENTION    
  INTEGER noWarning(0), addSecond(1), subtractSecond(2), alarm(3)  

NTPStratum  
Indicates the stratum of the clock. The stratum defines the accuracy of a time server. Higher the stratum, lower the accuracy. 0, unspecified 1, primary reference (e.g., calibrated atomic clock, radio clock) 2-255, secondary reference (via NTP)
TEXTUAL-CONVENTION    
  Integer32 0..255  

NTPSignedTimeValue  
The time in seconds that could represent signed quantities like time delay with respect to some source. This textual-convention is specific to Cisco implementation of NTP where 32-bit integers are used for such quantities. The signed integer part is in the first 16 bits and the fraction part is in the last 16 bits.
TEXTUAL-CONVENTION    
  OCTET STRING Size(4)  

NTPUnsignedTimeValue  
The time in seconds that could represent unsigned quantities like maximum error of the local clock with respect to some source. This textual-convention is specific to Cisco implementation of NTP where 32-bit integers are used for such quantities. The unsigned integer part is in the first 16 bits and the fraction part is in the last 16 bits.
TEXTUAL-CONVENTION    
  OCTET STRING Size(4)  

NTPRefId  
The reference clock identifier. In the case of stratum 0 (unspecified) or stratum 1 (primary reference source), this is a four-octet, left-justified, zero-padded ASCII string as defined in RFC-1305. In the case of stratum 2 and greater (secondary reference) this is the four-octet Internet address of the peer selected for synchronization. Some examples of stratum 0 identifiers are, DCN, DCN routing protocol NIST, NIST public modem TSP, TSP time protocol DTS, Digital Time Service Some examples of stratum 1 identifiers are, ATOM, Atomic clock (calibrated) VLF, VLF radio (OMEGA,, etc.) LORC, LORAN-C radionavigation GOES, GOES UHF environment satellite GPS, GPS UHF satellite positioning
TEXTUAL-CONVENTION    
  OCTET STRING Size(4)  

NTPTimeStamp  
NTP timestamps are represented as a 64-bit unsigned fixed-point number, in seconds relative to 00:00 on 1 January 1900. The integer part is in the first 32 bits and the fraction part is in the last 32 bits.
TEXTUAL-CONVENTION    
  OCTET STRING Size(8)  

NTPPollInterval  
The minimum interval between transmitted NTP messages, in seconds as a power of two. For instance, a value of six indicates a minimum interval of 64 seconds.
TEXTUAL-CONVENTION    
  Integer32 -20..20  

NTPAssocIdentifier  
The association identifier of the peer. Every peer with which an NTP server is associated with is identified by an association identifier.
TEXTUAL-CONVENTION    
  Integer32 0..2147483647  

NtpKeyIdentifier  
Description.
TEXTUAL-CONVENTION    
  Integer32 1..255  

NtpKeySource  
Description.
TEXTUAL-CONVENTION    
  INTEGER 0..255  

WsSwNtpSymmKeyEntry  
SEQUENCE    
  wsSwNtpKeyId NtpKeyIdentifier
  wsSwNtpKeyValue DisplayString
  wsSwNtpKeyIfTrusted TruthValue
  wsSwNtpKeyRowStatus RowStatus

WsSwNTPNeighborEntry  
SEQUENCE    
  wsSwNeighborPeerName DisplayString
  wsSwNeighborType INTEGER
  wsSwNeighborAuthKey INTEGER
  wsSwNeighborPrefPeer INTEGER
  wsSwNeighborNtpVersion INTEGER
  wsSwNeighborEntryStatus RowStatus

WsSwPeersStatusEntry  
SEQUENCE    
  wsSwPeersStatusIndex Unsigned32
  wsSwPeersStatusPeerAddress DisplayString
  wsSwPeersWhen DisplayString
  wsSwPeersStatusPort Integer32
  wsSwPeersHostAddress DisplayString
  wsSwPeersHostPort Integer32
  wsSwPeersStratum NTPStratum
  wsSwPeersPeerPoll NTPPollInterval
  wsSwPeersHostPoll NTPPollInterval
  wsSwPeersPrecision Integer32
  wsSwPeersRootDelay DisplayString
  wsSwPeersRootDispersion DisplayString
  wsSwPeersRefId NTPRefId
  wsSwPeersRefTime DisplayString
  wsSwPeersOrgTime DisplayString
  wsSwPeersReceiveTime DisplayString
  wsSwPeersTransmitTime DisplayString
  wsSwPeersReach Integer32
  wsSwPeersOffset DisplayString
  wsSwPeersDelay DisplayString
  wsSwPeersDispersion DisplayString
  wsSwPeersSanity INTEGER
  wsSwPeersValidity TruthValue
  wsSwPeersLocalMode DisplayString
  wsSwPeersPeerMode DisplayString
  wsSwPeersAssociationType INTEGER
  wsSwPeersAuthority INTEGER
  wsSwPeersLeapState INTEGER
  wsSwPeersFiltDelay DisplayString
  wsSwPeersFiltOffset DisplayString
  wsSwPeersFiltError DisplayString
  wsSwPeersRemotePollInterval Integer32

Defined Values

wsSwNTPModule 1.3.6.1.4.1.388.14.2.12.1
Description.
MODULE-IDENTITY    

ntpBroadcastDelay 1.3.6.1.4.1.388.14.2.12.1.1
Estimated round trip NTP broadcast delay. The value '0' has a special meaning in that it is used for clearing this object. The values 1-999999 when set give a measure of this delay in microseconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..999999  

ntpMasterClockMode 1.3.6.1.4.1.388.14.2.12.1.2
Description.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ntpMasterClockStratum 1.3.6.1.4.1.388.14.2.12.1.3
Description.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..15  

ntpBroadcastClientMode 1.3.6.1.4.1.388.14.2.12.1.4
Description.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

ntpaccessGroupPeer 1.3.6.1.4.1.388.14.2.12.1.5
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

ntpaccessGroupQueryOnly 1.3.6.1.4.1.388.14.2.12.1.6
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

ntpaccessGroupServe 1.3.6.1.4.1.388.14.2.12.1.7
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

ntpaccessGroupServeOnly 1.3.6.1.4.1.388.14.2.12.1.8
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

ntpAutoKey 1.3.6.1.4.1.388.14.2.12.1.9
Description.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), hostEnabled(1), clientOnlyEnabled(2)  

ntpAuthenticate 1.3.6.1.4.1.388.14.2.12.1.10
Description.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

wsSwNtpSystem 1.3.6.1.4.1.388.14.2.12.1.11
OBJECT IDENTIFIER    

wsSwSysLeap 1.3.6.1.4.1.388.14.2.12.1.11.1
Description.
Status: current Access: read-only
OBJECT-TYPE    
  NTPLeapIndicator  

wsSwSysStratum 1.3.6.1.4.1.388.14.2.12.1.11.2
Description.
Status: current Access: read-only
OBJECT-TYPE    
  NTPStratum  

wsSwSysPrecision 1.3.6.1.4.1.388.14.2.12.1.11.3
Description.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -20..20  

wsSwSysRootDelay 1.3.6.1.4.1.388.14.2.12.1.11.4
Description.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwSysRootDispersion 1.3.6.1.4.1.388.14.2.12.1.11.5
Description.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwSysRefId 1.3.6.1.4.1.388.14.2.12.1.11.6
Description.
Status: current Access: read-only
OBJECT-TYPE    
  NTPRefId  

wsSwSysRefTime 1.3.6.1.4.1.388.14.2.12.1.11.7
Description.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwSysPoll 1.3.6.1.4.1.388.14.2.12.1.11.8
Description.
Status: current Access: read-only
OBJECT-TYPE    
  NTPPollInterval  

wsSwSysClock 1.3.6.1.4.1.388.14.2.12.1.11.9
Description.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwSysFrequency 1.3.6.1.4.1.388.14.2.12.1.11.10
Description.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwSysJitter 1.3.6.1.4.1.388.14.2.12.1.11.11
Description.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwSysStability 1.3.6.1.4.1.388.14.2.12.1.11.12
Description.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwNtpSymmKeyTable 1.3.6.1.4.1.388.14.2.12.1.12
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsSwNtpSymmKeyEntry

wsSwNtpSymmKeyEntry 1.3.6.1.4.1.388.14.2.12.1.12.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsSwNtpSymmKeyEntry  

wsSwNtpKeyId 1.3.6.1.4.1.388.14.2.12.1.12.1.1
Description.
Status: current Access: read-only
OBJECT-TYPE    
  NtpKeyIdentifier  

wsSwNtpKeyValue 1.3.6.1.4.1.388.14.2.12.1.12.1.2
Description.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString  

wsSwNtpKeyIfTrusted 1.3.6.1.4.1.388.14.2.12.1.12.1.3
Description.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

wsSwNtpKeyRowStatus 1.3.6.1.4.1.388.14.2.12.1.12.1.4
Description.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wsSwNTPNeighborTable 1.3.6.1.4.1.388.14.2.12.1.13
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsSwNTPNeighborEntry

wsSwNTPNeighborEntry 1.3.6.1.4.1.388.14.2.12.1.13.1
Each peers' entry provides NTP information retrieved from a particular peer NTP server. Each peer is identified by a unique association identifier. Entries are automatically created when the user configures the NTP server to be associated with remote peers. Similarly entries are deleted when the user removes the peer association from the NTP server. Entries can also be created by the management station by setting values for the following objects: cntpPeersPeerAddress or cntpPeersPeerName, cntpPeersHostAddress and cntpPeersMode and making the cntpPeersEntryStatus as active(1). At the least, the management station has to set a value for cntpPeersPeerAddress or cntpPeersPeerName to make the row active.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsSwNTPNeighborEntry  

wsSwNeighborPeerName 1.3.6.1.4.1.388.14.2.12.1.13.1.1
The address of the peer.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwNeighborType 1.3.6.1.4.1.388.14.2.12.1.13.1.2
The type can be server(0), peer(1) or broadcast(2)
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER server(0), peer(1), broadcast(2)  

wsSwNeighborAuthKey 1.3.6.1.4.1.388.14.2.12.1.13.1.3
Valid key values are 1 to 65534. Value of -1 indicates Autokey option. Value 0 indicates removal of key.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER -1..255  

wsSwNeighborPrefPeer 1.3.6.1.4.1.388.14.2.12.1.13.1.4
This object specifies whether this peer is the preferred one over the others. The valid value for this are no(1) and yes(2)
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER no(1), yes(2)  

wsSwNeighborNtpVersion 1.3.6.1.4.1.388.14.2.12.1.13.1.5
The version values can range from 1 to 4. Value 0 indicates removal of version configuration
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER version1(1), version2(2), version3(3), version4(4)  

wsSwNeighborEntryStatus 1.3.6.1.4.1.388.14.2.12.1.13.1.6
The status object for this row. When a management station is creating a new row, it should set the value for cntpPeersPeerAddress at least, before the row can be made active(1).
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

wsSwPeersStatusTable 1.3.6.1.4.1.388.14.2.12.1.14
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WsSwPeersStatusEntry

wsSwPeersStatusEntry 1.3.6.1.4.1.388.14.2.12.1.14.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  WsSwPeersStatusEntry  

wsSwPeersStatusIndex 1.3.6.1.4.1.388.14.2.12.1.14.1.1
Description.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..32768  

wsSwPeersStatusPeerAddress 1.3.6.1.4.1.388.14.2.12.1.14.1.2
Description.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwPeersWhen 1.3.6.1.4.1.388.14.2.12.1.14.1.3
Time of Last NTP packet received
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwPeersStatusPort 1.3.6.1.4.1.388.14.2.12.1.14.1.4
Description.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsSwPeersHostAddress 1.3.6.1.4.1.388.14.2.12.1.14.1.5
The IP address of the local host. Multi-homing can be supported using this object.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwPeersHostPort 1.3.6.1.4.1.388.14.2.12.1.14.1.6
The UDP port number on which the local host receives NTP messages.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

wsSwPeersStratum 1.3.6.1.4.1.388.14.2.12.1.14.1.7
The stratum of the peer clock.
Status: current Access: read-only
OBJECT-TYPE    
  NTPStratum  

wsSwPeersPeerPoll 1.3.6.1.4.1.388.14.2.12.1.14.1.8
The interval at which the peer polls the local host.
Status: current Access: read-only
OBJECT-TYPE    
  NTPPollInterval  

wsSwPeersHostPoll 1.3.6.1.4.1.388.14.2.12.1.14.1.9
The interval at which the local host polls the peer.
Status: current Access: read-only
OBJECT-TYPE    
  NTPPollInterval  

wsSwPeersPrecision 1.3.6.1.4.1.388.14.2.12.1.14.1.10
Signed integer indicating the precision of the peer clock, in seconds to the nearest power of two. The value must be rounded to the next larger power of two; for instance, a 50-Hz (20 ms) or 60-Hz (16.67 ms) power-frequency clock would be assigned the value -5 (31.25 ms), while a 1000-Hz (1 ms) crystal-controlled clock would be assigned the value -9 (1.95 ms).
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 -20..20  

wsSwPeersRootDelay 1.3.6.1.4.1.388.14.2.12.1.14.1.11
A signed fixed-point number indicating the total round-trip delay in seconds, from the peer to the primary reference source at the root of the synchronization subnet.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwPeersRootDispersion 1.3.6.1.4.1.388.14.2.12.1.14.1.12
The maximum error in seconds, of the peer clock relative to the primary reference source at the root of the synchronization subnet. Only positive values greater than zero are possible.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwPeersRefId 1.3.6.1.4.1.388.14.2.12.1.14.1.13
The reference identifier of the peer.
Status: current Access: read-only
OBJECT-TYPE    
  NTPRefId  

wsSwPeersRefTime 1.3.6.1.4.1.388.14.2.12.1.14.1.14
The local time at the peer when its clock was last updated. If the peer clock has never been synchronized, the value is zero.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwPeersOrgTime 1.3.6.1.4.1.388.14.2.12.1.14.1.15
The local time at the peer, when its latest NTP message was sent. If the peer becomes unreachable the value is set to zero.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwPeersReceiveTime 1.3.6.1.4.1.388.14.2.12.1.14.1.16
The local time, when the latest NTP message from the peer arrived. If the peer becomes unreachable the value is set to zero.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwPeersTransmitTime 1.3.6.1.4.1.388.14.2.12.1.14.1.17
The local time at which the NTP message departed the sender.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwPeersReach 1.3.6.1.4.1.388.14.2.12.1.14.1.18
A shift register of used to determine the reachability status of the peer, with bits entering from the least significant (rightmost) end. A peer is considered reachable if at least one bit in this register is set to one i.e, if the value of this object is non-zero. The data in the shift register would be populated by the NTP protocol procedures.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

wsSwPeersOffset 1.3.6.1.4.1.388.14.2.12.1.14.1.19
The estimated offset of the peer clock relative to the local clock, in seconds. The host determines the value of this object using the NTP clock-filter algorithm.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwPeersDelay 1.3.6.1.4.1.388.14.2.12.1.14.1.20
The estimated round-trip delay of the peer clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the NTP clock-filter algorithm.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwPeersDispersion 1.3.6.1.4.1.388.14.2.12.1.14.1.21
The estimated maximum error of the peer clock relative to the local clock over the network path between them, in seconds. The host determines the value of this object using the NTP clock-filter algorithm.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwPeersSanity 1.3.6.1.4.1.388.14.2.12.1.14.1.22
Description.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER insane(1), sane(2)  

wsSwPeersValidity 1.3.6.1.4.1.388.14.2.12.1.14.1.23
Description.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

wsSwPeersLocalMode 1.3.6.1.4.1.388.14.2.12.1.14.1.24
Description.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwPeersPeerMode 1.3.6.1.4.1.388.14.2.12.1.14.1.25
Description.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwPeersAssociationType 1.3.6.1.4.1.388.14.2.12.1.14.1.26
Description.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER configured(1), dynamic(2), unknown(3)  

wsSwPeersAuthority 1.3.6.1.4.1.388.14.2.12.1.14.1.27
Description.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER master(1), selected(2), candidate(3), unknown(4)  

wsSwPeersLeapState 1.3.6.1.4.1.388.14.2.12.1.14.1.28
Description.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER add(1), sub(2), unsynced(3), unknown(4)  

wsSwPeersFiltDelay 1.3.6.1.4.1.388.14.2.12.1.14.1.29
Description.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwPeersFiltOffset 1.3.6.1.4.1.388.14.2.12.1.14.1.30
Description.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwPeersFiltError 1.3.6.1.4.1.388.14.2.12.1.14.1.31
Description.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

wsSwPeersRemotePollInterval 1.3.6.1.4.1.388.14.2.12.1.14.1.32
Remote Poll Interval
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

wsSwNtpMIBConformance 1.3.6.1.4.1.388.14.2.12.1.15
OBJECT IDENTIFIER    

wsSwNtpCompliance 1.3.6.1.4.1.388.14.2.12.1.15.1
Description.
Status: current Access: read-only
MODULE-COMPLIANCE    

wsSWNtpGroups 1.3.6.1.4.1.388.14.2.12.1.16
OBJECT IDENTIFIER    

wsSwNtpGroupAll 1.3.6.1.4.1.388.14.2.12.1.16.1
Description.
Status: current Access: read-only
OBJECT-GROUP