WHISP-APS-MIB

File: WHISP-APS-MIB.mib (160768 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF
WHISP-TCV2-MIB WHISP-GLOBAL-REG-MIB WHISP-BOX-MIBV2-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Counter32
Counter64 Gauge32 IpAddress
NOTIFICATION-TYPE TimeTicks Unsigned32
DisplayString PhysAddress MacAddress
OBJECT-GROUP WhispLUID WhispMACAddress
EventString whispModules whispBox
whispAps whispBoxEsn whispBoxRFPhysicalRadioEntry

Defined Types

WhispApsRFConfigRadioEntry  
SEQUENCE    
  radioFreqCarrier INTEGER
  radioDownlinkPercent INTEGER
  radioMaxRange INTEGER
  radioControlSlots INTEGER
  radioTransmitOutputPower INTEGER
  radioColorCode INTEGER

WhispLinkEntry  
SEQUENCE    
  linkLUID INTEGER
  linkDescr DisplayString
  linkPhysAddress PhysAddress
  linkMtu INTEGER
  linkSpeed Gauge32
  linkOperStatus INTEGER
  linkInOctets Counter32
  linkInUcastPkts Counter32
  linkInNUcastPkts Counter32
  linkInDiscards Counter32
  linkInError Counter32
  linkInUnknownProtos Counter32
  linkOutOctets Counter32
  linkOutUcastPkts Counter32
  linkOutNUcastPkts Counter32
  linkOutDiscards Counter32
  linkOutError Counter32
  linkOutQLen Gauge32
  linkSessState INTEGER
  linkESN PhysAddress
  linkRSSI INTEGER
  linkAveJitter Gauge32
  linkLastJitter Gauge32
  linkAirDelay INTEGER
  linkRegCount INTEGER
  linkReRegCount INTEGER
  linkTimeOut INTEGER
  linkLastRSSI INTEGER
  sessionCount INTEGER
  softwareVersion DisplayString
  softwareBootVersion DisplayString
  fpgaVersion DisplayString
  linkSiteName DisplayString
  avgPowerLevel DisplayString
  lastPowerLevel DisplayString
  sesDownLinkRate INTEGER
  sesDownLinkLimit INTEGER
  sesUpLinkRate INTEGER
  sesUpLinkLimit INTEGER
  adaptRate DisplayString
  sesLoUpCIR INTEGER
  sesLoDownCIR INTEGER
  sesHiUpCIR INTEGER
  sesHiDownCIR INTEGER
  platformVer INTEGER
  smSessionTmr TimeTicks
  smSessionSeqNumMismatch Counter32
  dataVCNum INTEGER
  hiPriQEn INTEGER
  dataVCNumHiQ INTEGER
  linkInOctetsHiQ Counter32
  linkInUcastPktsHiQ Counter32
  linkInNUcastPktsHiQ Counter32
  linkInDiscardsHiQ Counter32
  linkInErrorHiQ Counter32
  linkInUnknownProtosHiQ Counter32
  linkOutOctetsHiQ Counter32
  linkOutUcastPktsHiQ Counter32
  linkOutNUcastPktsHiQ Counter32
  linkOutDiscardsHiQ Counter32
  linkOutErrorHiQ Counter32
  vcQOverflow Counter32
  vcQOverflowHiQ Counter32
  p7p8HiPriQEn INTEGER
  p7p8HiPriQ Counter32
  linkAirDelayns INTEGER
  linkQualityAPData DisplayString
  linkManagementIP IpAddress
  linkFragmentsReceived1XVertical Counter32
  linkFragmentsReceived2XVertical Counter32
  linkFragmentsReceived3XVertical Counter32
  linkFragmentsReceived4XVertical Counter32
  signalToNoiseRatioVertical INTEGER
  radiusReplyMsg DisplayString
  autoUpdateStatus INTEGER
  radiusFramedIPAddress IpAddress
  radiusFramedIPNetmask IpAddress
  radiusDefaultGateway IpAddress
  linkFragmentsReceived1XHorizontal Counter32
  linkFragmentsReceived2XHorizontal Counter32
  linkFragmentsReceived3XHorizontal Counter32
  linkFragmentsReceived4XHorizontal Counter32
  signalToNoiseRatioHorizontal INTEGER
  linkSignalStrengthRatio DisplayString
  linkRadioDbmHorizontal DisplayString
  linkRadioDbmVertical DisplayString
  maxSMTxPwr INTEGER
  productType INTEGER
  linkAdaptRateLowPri INTEGER
  linkAdaptRateHighPri INTEGER
  avgPowerLevelInt INTEGER
  mimoPowerLevelVertical INTEGER
  mimoPowerLevelHorizontal INTEGER
  linkSwVersion DisplayString

WhispFailedRegEntry  
SEQUENCE    
  regFailSeqNum Counter32
  regFailESN PhysAddress
  regGrantReason INTEGER
  regFailTime TimeTicks
  regFailReasonText DisplayString

Defined Values

whispApsMibModule 1.3.6.1.4.1.161.19.1.1.12
This module contains MIB definitions for APs.
MODULE-IDENTITY    

whispApsConfig 1.3.6.1.4.1.161.19.3.1.1
OBJECT IDENTIFIER    


whispApsLinkTestConfig 1.3.6.1.4.1.161.19.3.1.2.1
OBJECT IDENTIFIER    

whispApsLinkTestResult 1.3.6.1.4.1.161.19.3.1.2.2
OBJECT IDENTIFIER    

whispApsGPS 1.3.6.1.4.1.161.19.3.1.3
OBJECT IDENTIFIER    

whispApsEvent 1.3.6.1.4.1.161.19.3.1.5
OBJECT IDENTIFIER    

whispApsRegEvent 1.3.6.1.4.1.161.19.3.1.5.1
OBJECT IDENTIFIER    

whispGPSEvent 1.3.6.1.4.1.161.19.3.1.5.2
OBJECT IDENTIFIER    

whispApsDfsEvent 1.3.6.1.4.1.161.19.3.1.5.3
OBJECT IDENTIFIER    

whispApRegulatoryEvent 1.3.6.1.4.1.161.19.3.1.5.4
OBJECT IDENTIFIER    

whispApRFOverloadEvent 1.3.6.1.4.1.161.19.3.1.5.5
OBJECT IDENTIFIER    

whispApsGroups 1.3.6.1.4.1.161.19.3.1.6
OBJECT IDENTIFIER    

whispApsFrUtlStats 1.3.6.1.4.1.161.19.3.1.12
OBJECT IDENTIFIER    

whispApsFrUtlStatsIntervalLow 1.3.6.1.4.1.161.19.3.1.12.1
OBJECT IDENTIFIER    

whispApsFrUtlStatsIntervalMedium 1.3.6.1.4.1.161.19.3.1.12.2
OBJECT IDENTIFIER    

whispApsFrUtlStatsIntervalHigh 1.3.6.1.4.1.161.19.3.1.12.3
OBJECT IDENTIFIER    

whispApsStatus 1.3.6.1.4.1.161.19.3.1.7
OBJECT IDENTIFIER    

whispApsDNS 1.3.6.1.4.1.161.19.3.1.9
OBJECT IDENTIFIER    

whispApsControls 1.3.6.1.4.1.161.19.3.1.11
OBJECT IDENTIFIER    

whispApsRFConfig 1.3.6.1.4.1.161.19.3.1.10
OBJECT IDENTIFIER    

gpsInput 1.3.6.1.4.1.161.19.3.1.1.1
The variable is deprecated. See gpsInput in whispBoxConfig.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER generateSyncSignal(0), syncToReceivedSignalTimingPort(1), syncToReceivedSignalPowerPort(2)  

rfFreqCarrier 1.3.6.1.4.1.161.19.3.1.1.2
The primary transmit frequency. Also see radioFreqCarrier.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER wired(0)  

apLinkSpeed 1.3.6.1.4.1.161.19.3.1.1.3
The variable is deprecated.
Status: obsolete Access: read-write
OBJECT-TYPE    
  DisplayString  

dwnLnkData 1.3.6.1.4.1.161.19.3.1.1.4
This attribute is deprecated. Please see radioDownlinkPercent.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER 1..99  

highPriorityUpLnkPct 1.3.6.1.4.1.161.19.3.1.1.5
Percentage of uplink slots for high priority data.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER 0..99  

numUAckSlots 1.3.6.1.4.1.161.19.3.1.1.6
Total number of upstream ack slots.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER  

uAcksReservHigh 1.3.6.1.4.1.161.19.3.1.1.7
Total number of upstream high priority ack slots
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER  

numDAckSlots 1.3.6.1.4.1.161.19.3.1.1.8
Total number of downstream ack slots.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER  

dAcksReservHigh 1.3.6.1.4.1.161.19.3.1.1.9
Total number of high priority downstream ack slots.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER  

numCtlSlots 1.3.6.1.4.1.161.19.3.1.1.10
This OID is deprecated, please use numCtlSlotsHW.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER  

numCtlSlotsReserveHigh 1.3.6.1.4.1.161.19.3.1.1.11
Total number of High priority upstream control (contention) slots.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER  

upLnkDataRate 1.3.6.1.4.1.161.19.3.1.1.12
Sustained uplink bandwidth cap.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

upLnkLimit 1.3.6.1.4.1.161.19.3.1.1.13
Burst uplink bandwidth cap.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dwnLnkDataRate 1.3.6.1.4.1.161.19.3.1.1.14
Sustained downlink bandwidth cap.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dwnLnkLimit 1.3.6.1.4.1.161.19.3.1.1.15
Burst downlink bandwidth cap.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

sectorID 1.3.6.1.4.1.161.19.3.1.1.16
Advertise sector number for an AP. Not supported on 450 platform.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..15  

maxRange 1.3.6.1.4.1.161.19.3.1.1.17
This attribute is deprecated. Please see radioMaxRange.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER  

airLinkSecurity 1.3.6.1.4.1.161.19.3.1.1.18
Air Link Security. desEnhancedAndAuthentication(2) and authenticationIfAvailable(3) are only for APAS.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER standard(0), desEnhanced(1), desEnhancedAndAuthentication(2), authenticationIfAvailable(3)  

berMode 1.3.6.1.4.1.161.19.3.1.1.19
AP backgroup BER mode.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER berStream(0), noBerStream(1)  

asIP1 1.3.6.1.4.1.161.19.3.1.1.20
Obsoleted. Configure with whispApsDNS.authServer1.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

asIP2 1.3.6.1.4.1.161.19.3.1.1.21
Obsoleted. Configure with whispApsDNS.authServer2.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

asIP3 1.3.6.1.4.1.161.19.3.1.1.22
Obsoleted. Configure with whispApsDNS.authServer3.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

lanIpAp 1.3.6.1.4.1.161.19.3.1.1.23
LAN IP.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

lanMaskAp 1.3.6.1.4.1.161.19.3.1.1.24
LAN subnet mask.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

defaultGwAp 1.3.6.1.4.1.161.19.3.1.1.25
Default gateway
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

privateIp 1.3.6.1.4.1.161.19.3.1.1.26
Private IP.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

gpsTrap 1.3.6.1.4.1.161.19.3.1.1.27
Variable to enable/disable GPS sync/out-sync traps.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER gpsTrapDisabled(0), gpsTrapEnabled(1)  

regTrap 1.3.6.1.4.1.161.19.3.1.1.28
Variable to enable/disable registration complete/lost traps.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER regTrapDisabled(0), regTrapEnabled(1)  

txSpreading 1.3.6.1.4.1.161.19.3.1.1.29
Variable to enable/disable Transmit Frame Spreading. This option is for FSK only.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER txSpreadingDisabled(0), txSpreadingEnabled(1)  

apBeaconInfo 1.3.6.1.4.1.161.19.3.1.1.30
Variable to enable/disable displaying AP beacon info through AP eval.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enableApBeaconInfo(0), disableApBeaconInfo(1)  

authMode 1.3.6.1.4.1.161.19.3.1.1.31
Variable to enable/disable authentication. The authentication optional mode is for APs only. This variable can only be set when authentication feature is enabled. Setting it to 1 will use a BAM server for authentication of SMs. Setting it to 2 will make use of the Authentication Key on the AP for authenticating SMs. The keys must match on SM and AP in order for the SM to be authenticated in this mode.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER authenticationDisabled(0), authenticationRequiredBam(1), authenticationRequiredAP(3), authenticationRequiredAAA(4)  

authKeyAp 1.3.6.1.4.1.161.19.3.1.1.32
Authentication key. It should be 32 character long. Can be used on MultiPoint AP if AP Authentication mode is selected. Otherwise, it is used on Backhauls.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

encryptionMode 1.3.6.1.4.1.161.19.3.1.1.33
Variable to enable/disable encryption.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER encryptionDisabled(0), encryptionEnabled(1)  

ntpServerIp 1.3.6.1.4.1.161.19.3.1.1.34
Obsoleted. Configure with whispApsDNS.ntpServer1, whispApsDNS.ntpServer2, and whispApsDNS.ntpServer3.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

broadcastRetryCount 1.3.6.1.4.1.161.19.3.1.1.35
Broadcast Repeat Count : Range 0 -- 2. For APs.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

encryptDwBroadcast 1.3.6.1.4.1.161.19.3.1.1.36
To enable or disable Encrypted Downlink Broadcast. For FSK APs.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

updateAppAddress 1.3.6.1.4.1.161.19.3.1.1.37
Update Application Address.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

dfsConfig 1.3.6.1.4.1.161.19.3.1.1.38
To configure proper regions for Dynamic Frequency Shifting. For 5.2/5.4/5.7 GHz radios.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

vlanEnable 1.3.6.1.4.1.161.19.3.1.1.39
To enable or disable VLAN.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

configSource 1.3.6.1.4.1.161.19.3.1.1.40
To configure CIR, MIR and VLAN through SM or BAM.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER bam(0), sm(1), bamsm(2)  

apRateAdapt 1.3.6.1.4.1.161.19.3.1.1.41
To enable or disable double rate.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER onex(0), onextwox(1), onextwoxthreex(2)  

numCtlSlotsHW 1.3.6.1.4.1.161.19.3.1.1.42
This attribute is deprecated. Please see radioControlSlots.
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER  

displayAPEval 1.3.6.1.4.1.161.19.3.1.1.43
If enable, it allows display of AP Eval Data at the SM.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(0), disable(1)  

smIsolation 1.3.6.1.4.1.161.19.3.1.1.44
(0) -- Disable SM Isolation. (1) -- Enable SM Isolation by blocking SM destined packets. (2) -- Enable SM Isolation by forwarding SM packets upstream.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER smIsolationDisable(0), smIsolationDrop(1), smIsolationFwd(2)  

ipAccessFilterEnable 1.3.6.1.4.1.161.19.3.1.1.45
To enable or disable IP access filtering to Management functions. (0) - IP access will be allowed from all addresses. (1) - IP access will be controlled using allowedIPAccess1-3 entries.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

allowedIPAccess1 1.3.6.1.4.1.161.19.3.1.1.46
Allow access to AP Management from this IP. 0 is default setting to allow from all IPs.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

allowedIPAccess2 1.3.6.1.4.1.161.19.3.1.1.47
Allow access to AP Management from this IP. 0 is default setting to allow from all IPs.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

allowedIPAccess3 1.3.6.1.4.1.161.19.3.1.1.48
Allow access to AP Management from this IP. 0 is default setting to allow from all IPs.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

tslBridging 1.3.6.1.4.1.161.19.3.1.1.49
1 = We are performing Translation Bridging 0 = We are not.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

untranslatedArp 1.3.6.1.4.1.161.19.3.1.1.50
1 = We are sending untranslated ARP response. 0 = We are not.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

limitFreqBand900 1.3.6.1.4.1.161.19.3.1.1.51
1 = We are limiting the freq band of 900 radios. 0 = We are not.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

txPwrLevel 1.3.6.1.4.1.161.19.3.1.1.52
Deprecated, use 'transmitterOP' instead.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER  

rfFreqCaralt1 1.3.6.1.4.1.161.19.3.1.1.53
First DFS Alternate RF Frequency. (Only available for DFS radios) Used as a backup frequency when Radar is detected on DFS enabled Radios. The frequencies are: 5.4 radios:(5475,5485,5490 OFDM only),5495,5500,5505,5510,5515,5520,5525, 5530,5535,5540,5545,5550,5555,5560,5565,5570,5575,5580,5585,5590,5595, 5600,5605,5610,5615,5620,5625,5630,5635,5640,5645,5650,5655,5660,5665, 5670,5675,5680,5685,5690,5695,5700,5705,(5710,5715 OFDM Only). (5.7 Platform 10 (SAL) radios with non-connectorized antennas do not support DFS) 5.7 radios:5745,5750,5755,5760,5765,5770,5775,5780,5785,5790,5795,5800,5805. 5.7 radios with ISM enabled :5735,5740,5745,5750,5755,5760,5765,5770,5775, 5780,5785,5790,5795,5800,5805,5810,5815,5820,5825,5830,5835,5840. 0: None.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0)  

rfFreqCaralt2 1.3.6.1.4.1.161.19.3.1.1.54
Second DFS Alternate RF Frequency. (Only available for DFS radios) Used as a backup frequency when Radar is detected on DFS enabled Radios. The frequencies are: 5.4 radios:(5475,5485,5490 OFDM only),5495,5500,5505,5510,5515,5520,5525, 5530,5535,5540,5545,5550,5555,5560,5565,5570,5575,5580,5585,5590,5595, 5600,5605,5610,5615,5620,5625,5630,5635,5640,5645,5650,5655,5660,5665, 5670,5675,5680,5685,5690,5695,5700,5705,(5710,5715 OFDM Only). (5.7 Platform 10 (SAL) radios with non-connectorized antennas do not support DFS) 5.7 radios:5745,5750,5755,5760,5765,5770,5775,5780,5785,5790,5795,5800,5805. 5.7 radios with ISM enabled :5735,5740,5745,5750,5755,5760,5765,5770,5775, 5780,5785,5790,5795,5800,5805,5810,5815,5820,5825,5830,5835,5840. 0: None.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0)  

scheduleWhitening 1.3.6.1.4.1.161.19.3.1.1.55
1 = Schedule Whitening allowed. 0 = Schedule Whitening not allowed. This option is for FSK only
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

remoteSpectrumAnalysisDuration 1.3.6.1.4.1.161.19.3.1.1.56
Value in seconds for a remote spectrum analysis on an SM. Range is 10-1000 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 10..1000  

remoteSpectrumAnalyzerLUID 1.3.6.1.4.1.161.19.3.1.1.57
Get will always return 0. Set will start Remote Spectrum Analyzer on specified LUID. *Warning* This will cause the SM to disconnect from the AP! You will lose the session for the specified duration! If general error was returned then the LUID does not have an active session, or the SM does not support Remote Spectrum Analysis.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 2..239  

bhReReg 1.3.6.1.4.1.161.19.3.1.1.58
Allows BHS re-registration every 24 hours. Enable allows re-registration and Disable does not. 24 Hour Encryption Refresh.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dlnkBcastCIR 1.3.6.1.4.1.161.19.3.1.1.59
Downlink Broadcast CIR (kbps)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

verifyGPSChecksum 1.3.6.1.4.1.161.19.3.1.1.60
Enable/Disable verification of GPS message checksums.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER doNotVerifyGPSMessageChecksum(0), verifyGPSMessageChecksum(1)  

apVlanOverride 1.3.6.1.4.1.161.19.3.1.1.61
Setting this option will cause an AP to retain its VLAN settings when turning it into an SM. It will be mostly helpful for running spectrum analysis on the AP. Since doing that requires the AP to be turned into an SM, enabling this option will allow you to keep the AP's VLAN configuration in place while the AP is running as an SM.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

dhcpRelayAgentEnable 1.3.6.1.4.1.161.19.3.1.1.62
Enable or Disable MultiPoint AP acting as DHCP Relay Agent for all SMs and Clients underneath it. (0) - Relay Agent disabled - SM/CPE devices will perform DHCP normally (1) - Relay Agent enabled - AP will intercept DHCP DISCOVER message from SM and CPE, insert Option 82 containing SM's MAC address, and forward request to specified DHCP server.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), fullRelay(1), option82Only(2)  

dhcpRelayAgentSrvrIP 1.3.6.1.4.1.161.19.3.1.1.63
Obsoleted. Configure with whispApsDNS.dhcprServer.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

colorCodeRescanTimer 1.3.6.1.4.1.161.19.3.1.1.64
Time in minutes for the subscriber to begin the idle timer. This timer will begin as soon as a session is started. This only fires if the device is in session with a non-primary color code. A value of zero (0) disables this timer (MultiPoint system Only)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..43200  

colorCodeRescanIdleTimer 1.3.6.1.4.1.161.19.3.1.1.65
Time in minutes for the subscriber to check for an idle state. If an period has pass where no unicast RF traffic has occured (idle), then the subscriber will begin to rescan. This timer will wait until the timer set in colorCodeRescanTimer has expired before beginning. This timer only fires if the device is in session with a non-primary color code. A value of zero (0) mean to rescan without waiting for idle. (MultiPoint system Only)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..60  

authKeyOptionAP 1.3.6.1.4.1.161.19.3.1.1.66
This option is for Multipoint APs only. This option will only be used if Authentication Mode is set to AP Pre-Shared Key. 0 - Use default key. 1 - Use set key.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER useDefault(0), useKeySet(1)  

asIP4 1.3.6.1.4.1.161.19.3.1.1.67
Obsoleted. Configure with whispApsDNS.authServer4.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

asIP5 1.3.6.1.4.1.161.19.3.1.1.68
Obsoleted. Configure with whispApsDNS.authServer5.
Status: obsolete Access: read-write
OBJECT-TYPE    
  IpAddress  

onlyAllowVer95OrAbove 1.3.6.1.4.1.161.19.3.1.1.69
Only allow subscribers that are running version 9.5 or above. Any radio that has a version below 9.5 will not be allowed to register.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER onlyAllowVer95OrAboveDisabled(0), onlyAllowVer95OrAboveEnabled(1)  

apRxDelay 1.3.6.1.4.1.161.19.3.1.1.70
This is used for engineering debug and needs to be removed or moved to eng MIB before releasing the MIB.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

qinqEthType 1.3.6.1.4.1.161.19.3.1.1.71
EtherType for QinQ (802.1ad) outer tag (S-Tag). 0x88a8 by default.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER x88a8(0), x8100(1), x9100(2), x9200(3), x9300(4)  

fskSMTxPwrCntl 1.3.6.1.4.1.161.19.3.1.1.72
Enable/Disable AP control of SM TX power. For FSK AP radios capable of Transmit Power Control.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

fskSMRcvTargetLvl 1.3.6.1.4.1.161.19.3.1.1.73
Desired SM Receive Level at AP (dBm, Range -40dBm to -80 dBm).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -80..-40  

authSharedSecret1 1.3.6.1.4.1.161.19.3.1.1.74
Authentication Server 1 Shared Secret.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

authSharedSecret2 1.3.6.1.4.1.161.19.3.1.1.75
Authentication Server 2 Shared Secret.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

authSharedSecret3 1.3.6.1.4.1.161.19.3.1.1.76
Authentication Server 3 Shared Secret.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

whispUsrAuthSharedSecret1 1.3.6.1.4.1.161.19.3.1.1.79
Obsoleted. Use whispApsConfig.authSharedSecret1.
Status: obsolete Access: read-write
OBJECT-TYPE    
  DisplayString  

whispUsrAuthSharedSecret2 1.3.6.1.4.1.161.19.3.1.1.80
Obsoleted. Use whispApsConfig.authSharedSecret2.
Status: obsolete Access: read-write
OBJECT-TYPE    
  DisplayString  

whispUsrAuthSharedSecret3 1.3.6.1.4.1.161.19.3.1.1.81
Obsoleted. Use whispApsConfig.authSharedSecret3.
Status: obsolete Access: read-write
OBJECT-TYPE    
  DisplayString  

whispUsrAcctSvr1 1.3.6.1.4.1.161.19.3.1.1.82
Obsoleted. Use whispApsDNS.authServer1.
Status: obsolete Access: read-write
OBJECT-TYPE    
  DisplayString  

whispUsrAcctSvr2 1.3.6.1.4.1.161.19.3.1.1.83
Obsoleted. Use whispApsDNS.authServer2.
Status: obsolete Access: read-write
OBJECT-TYPE    
  DisplayString  

whispUsrAcctSvr3 1.3.6.1.4.1.161.19.3.1.1.84
Obsoleted. Use whispApsDNS.authServer3.
Status: obsolete Access: read-write
OBJECT-TYPE    
  DisplayString  

whispUsrAuthPhase1 1.3.6.1.4.1.161.19.3.1.1.85
Select method for User Authentication
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER md5(0)  

whispWebUseAuthServer 1.3.6.1.4.1.161.19.3.1.1.86
Obsoleted. Use whispApsDNS.authServer[1-3].
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER useRADIUSAccountingSvr(0), useRADIUSAuthenticationSvr(1)  

dropSession 1.3.6.1.4.1.161.19.3.1.1.87
SM/BHS MAC Address to drop session from the AP/BHM.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

uGPSPower 1.3.6.1.4.1.161.19.3.1.1.88
Enable or Disable power supply to Universal GPS module (UGPS capable APs only, when GPS_output_enable is NOT set).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1)  

timeZone 1.3.6.1.4.1.161.19.3.1.1.89
Set the timezone offset for the radio. This change takes affect dynamically. The available timezones are: 0 : (UTC) UTC - Coordinated Universal Time 1 : (UTC) GMT - Greenwich Mean Time 2 : (UTC) WET - Western European Time 3 : (UTC-12) BIT - Baker Island Time 4 : (UTC-11) SST - Samoa Standard Time 5 : (UTC-10) CKT - Cook Island Time 6 : (UTC-10) HAST - Hawaii-Aleutian Standard Time 7 : (UTC-10) HST - Hawaii Standard Time 8 : (UTC-10) TAHT - Tahiti Time 9 : (UTC-09:30) MIT - Marquesas Islands Time 10 : (UTC-09) AKST - Alaska Standard Time 11 : (UTC-09) GIT - Gambier Island Time 12 : (UTC-09) HADT - Hawaii-Aleutian Daylight Time 13 : (UTC-08) AKDT - Alaska Daylight Time 14 : (UTC-08) CIST - Clipperton Island Standard Time 15 : (UTC-08) PST - Pacific Standard Time (North America) 16 : (UTC-07) MST - Mountain Standard Time (North America) 17 : (UTC-07) PDT - Pacific Daylight Time (North America) 18 : (UTC-06) CST - Central Standard Time (North America) 19 : (UTC-06) EAST - Easter Island Standard Time 20 : (UTC-06) GALT - Galapagos Time 21 : (UTC-06) MDT - Mountain Daylight Time (North America) 22 : (UTC-05) CDT - Central Daylight Time (North America) 23 : (UTC-05) COT - Colombia Time 24 : (UTC-05) ECT - Ecuador Time 25 : (UTC-05) EST - Eastern Standard Time (North America) 26 : (UTC-04:30) VET - Venezuelan Standard Time 27 : (UTC-04) AST - Atlantic Standard Time 28 : (UTC-04) BOT - Bolivia Time 29 : (UTC-04) CLT - Chile Standard Time 30 : (UTC-04) COST - Colombia Summer Time 31 : (UTC-04) ECT - Eastern Caribbean Time (does not recognise DST) 32 : (UTC-04) EDT - Eastern Daylight Time (North America) 33 : (UTC-04) FKT - Falkland Islands Time 34 : (UTC-04) GYT - Guyana Time 35 : (UTC-03:30) NST - Newfoundland Standard Time 36 : (UTC-03:30) NT - Newfoundland Time 37 : (UTC-03) ADT - Atlantic Daylight Time 38 : (UTC-03) ART - Argentina Time 39 : (UTC-03) BRT - Brasilia Time 40 : (UTC-03) CLST - Chile Summer Time 41 : (UTC-03) FKST - Falkland Islands Summer Time 42 : (UTC-03) GFT - French Guiana Time 43 : (UTC-03) UYT - Uruguay Standard Time 44 : (UTC-02:30) NDT - Newfoundland Daylight Time 45 : (UTC-02) GST - South Georgia and the South Sandwich Islands 46 : (UTC-02) UYST - Uruguay Summer Time 47 : (UTC-01) AZOST - Azores Standard Time 48 : (UTC-01) CVT - Cape Verde Time 49 : (UTC+01) BST - British Summer Time (British Standard Time from Feb 1968 to Oct 1971) 50 : (UTC+01) CET - Central European Time 51 : (UTC+01) DFT - AIX specific equivalent of Central European Time 52 : (UTC+01) IST - Irish Summer Time 53 : (UTC+01) WAT - West Africa Time 54 : (UTC+01) WEDT - Western European Daylight Time 55 : (UTC+01) WEST - Western European Summer Time 56 : (UTC+02) CAT - Central Africa Time 57 : (UTC+02) CEDT - Central European Daylight Time 58 : (UTC+02) CEST - Central European Summer Time 59 : (UTC+02) EET - Eastern European Time 60 : (UTC+02) IST - Israel Standard Time 61 : (UTC+02) SAST - South African Standard Time 62 : (UTC+03) AST - Arab Standard Time (Kuwait, Riyadh) 63 : (UTC+03) AST - Arabic Standard Time (Baghdad) 64 : (UTC+03) EAT - East Africa Time 65 : (UTC+03) EEDT - Eastern European Daylight Time 66 : (UTC+03) EEST - Eastern European Summer Time 67 : (UTC+03) MSK - Moscow Standard Time 68 : (UTC+03:30) IRST - Iran Standard Time 69 : (UTC+04) AMT - Armenia Time 70 : (UTC+04) AST - Arabian Standard Time (Abu Dhabi, Muscat) 71 : (UTC+04) AZT - Azerbaijan Time 72 : (UTC+04) GET - Georgia Standard Time 73 : (UTC+04) MSD - Moscow Summer Time 74 : (UTC+04) MUT - Mauritius Time 75 : (UTC+04) RET - Reunion Time 76 : (UTC+04) SAMT - Samara Time 77 : (UTC+04) SCT - Seychelles Time 78 : (UTC+04:30) AFT - Afghanistan Time 79 : (UTC+05) AMST - Armenia Summer Time 80 : (UTC+05) HMT - Heard and McDonald Islands Time 81 : (UTC+05) PKT - Pakistan Standard Time 82 : (UTC+05) YEKT - Yekaterinburg Time 83 : (UTC+05:30) IST - Indian Standard Time 84 : (UTC+05:30) SLT - Sri Lanka Time 85 : (UTC+05:45) NPT - Nepal Time 86 : (UTC+06) BIOT - British Indian Ocean Time 87 : (UTC+06) BST - Bangladesh Standard Time 88 : (UTC+06) BTT - Bhutan Time 89 : (UTC+06) OMST - Omsk Time 90 : (UTC+06:30) CCT - Cocos Islands Time 91 : (UTC+06:30) MST - Myanmar Standard Time 92 : (UTC+07) CXT - Christmas Island Time 93 : (UTC+07) ICT - Indochina Time 94 : (UTC+07) KRAT - Krasnoyarsk Time 95 : (UTC+07) THA - Thailand Standard Time 96 : (UTC+08) ACT - ASEAN Common Time 97 : (UTC+08) AWST - Australian Western Standard Time 98 : (UTC+08) BDT - Brunei Time 99 : (UTC+08) CST - China Standard Time 100 : (UTC+08) HKT - Hong Kong Time 101 : (UTC+08) IRKT - Irkutsk Time 102 : (UTC+08) MST - Malaysian Standard Time 103 : (UTC+08) PST - Philippine Standard Time 104 : (UTC+08) SST - Singapore Standard Time 105 : (UTC+09) AWDT - Australian Western Daylight Time 106 : (UTC+09) JST - Japan Standard Time 107 : (UTC+09) KST - Korea Standard Time 108 : (UTC+09) YAKT - Yakutsk Time 109 : (UTC+09:30) ACST - Australian Central Standard Time 110 : (UTC+10) AEST - Australian Eastern Standard Time 111 : (UTC+10) ChST - Chamorro Standard Time 112 : (UTC+10) VLAT - Vladivostok Time 113 : (UTC+10:30) ACDT - Australian Central Daylight Time 114 : (UTC+10:30) LHST - Lord Howe Standard Time 115 : (UTC+11) AEDT - Australian Eastern Daylight Time 116 : (UTC+11) MAGT - Magadan Time 117 : (UTC+11) SBT - Solomon Islands Time 118 : (UTC+11:30) NFT - Norfolk Time[1] 119 : (UTC+12) FJT - Fiji Time 120 : (UTC+12) GILT - Gilbert Island Time 121 : (UTC+12) PETT - Kamchatka Time 122 : (UTC+12:45) CHAST - Chatham Standard Time 123 : (UTC+13) PHOT - Phoenix Island Time 124 : (UTC+14) LINT - Line Islands Time
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..124  

ofdmSMRcvTargetLvl 1.3.6.1.4.1.161.19.3.1.1.90
Desired SM Receive Level at AP (dBm, Range -40dBm to -80 dBm). As of release 12.1, on MIMO systems this is a combined power level value.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -80..-40  

radiusPort 1.3.6.1.4.1.161.19.3.1.1.91
Port used to connect to the RADIUS server. Default is 1812.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

radiusAcctPort 1.3.6.1.4.1.161.19.3.1.1.92
Port used to for RADIUS Accounting. Default is 1813.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

lastSesStatsReset 1.3.6.1.4.1.161.19.3.1.1.93
Displays the timestamp of last reset of session stats or None otherwise.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

resetSesStats 1.3.6.1.4.1.161.19.3.1.1.94
Resets the session stats if true.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER noReset(0), reset(1)  

rfOLTrap 1.3.6.1.4.1.161.19.3.1.1.95
Enable/Disable SNMP Trap for when RF Overload exceeds configured Threshold level.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

rfOLThreshold 1.3.6.1.4.1.161.19.3.1.1.96
Percent of packet overload in the RF Downlink where SNMP is generated and sent to Network Manager.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..100  

rfOLEnable 1.3.6.1.4.1.161.19.3.1.1.97
Enable/Disable Throughput RF Overload Monitoring monitoring.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

actionListFilename 1.3.6.1.4.1.161.19.3.1.1.98
Name of the file that contains the Action List for Auto update commands from CNUT
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

enableAutoupdate 1.3.6.1.4.1.161.19.3.1.1.99
Enables/Disables auto-update of the SM's under an AP
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

accountingSmReAuthInterval 1.3.6.1.4.1.161.19.3.1.1.100
Select Interval for Reauthentication of SM
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

syslogDomainNameAppend 1.3.6.1.4.1.161.19.3.1.1.101
This attribute is deprecated. Use syslogDomainNameAppend in whispBoxAttributesGroup
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER disableDomain(0), appendDomain(1)  

syslogServerAddr 1.3.6.1.4.1.161.19.3.1.1.102
This attribute is deprecated. Use syslogServerAddr in whispBoxAttributesGroup
Status: deprecated Access: read-write
OBJECT-TYPE    
  DisplayString  

syslogServerPort 1.3.6.1.4.1.161.19.3.1.1.103
This attribute is deprecated. Use syslogServerPort in whispBoxAttributesGroup
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

syslogXmitAP 1.3.6.1.4.1.161.19.3.1.1.104
Enables/Disables transmission of Syslogs from AP/BHM
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

syslogXmitSMs 1.3.6.1.4.1.161.19.3.1.1.105
Enables/Disables transmission of Syslogs from connected SMs/BHS. This can be over-ridden by the setting on individual SMs/ the BHS.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

accountingInterimUpdateInterval 1.3.6.1.4.1.161.19.3.1.1.106
Select Interval for Interim Updates
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

gpsOutputEn 1.3.6.1.4.1.161.19.3.1.1.107
Enable or Disable GPS sync output enable.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER off(0), on(1)  

removeIdleSMs 1.3.6.1.4.1.161.19.3.1.1.108
Setting this to a value 1 will remove all SMs which are in Idle state from AP's Session list.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER stopped(0), start(1)  

lastTimeIdleSMsRemoved 1.3.6.1.4.1.161.19.3.1.1.109
Displays the timestamp of last removal of Idle SMs from AP's Session list
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

radioMode 1.3.6.1.4.1.161.19.3.1.1.206
This OID is obsolete.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER mimoOnly(2)  

rfTelnetAccess 1.3.6.1.4.1.161.19.3.1.1.207
Allows/prohibits uplink Telnet access (SM->AP).
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

upLnkMaxBurstDataRate 1.3.6.1.4.1.161.19.3.1.1.208
Maximum burst uplink rate.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

dwnLnkMaxBurstDataRate 1.3.6.1.4.1.161.19.3.1.1.209
Maximum burst downlink rate.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

rfPPPoEPADIForwarding 1.3.6.1.4.1.161.19.3.1.1.210
Enables/disables forwarding of PPPoE PADI packets from AP to SM.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

allowedIPAccessNMLength1 1.3.6.1.4.1.161.19.3.1.1.211
Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowed
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..32  

allowedIPAccessNMLength2 1.3.6.1.4.1.161.19.3.1.1.212
Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowed
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..32  

allowedIPAccessNMLength3 1.3.6.1.4.1.161.19.3.1.1.213
Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowed
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..32  

bridgeFloodUnknownsEnable 1.3.6.1.4.1.161.19.3.1.1.214
Forward unicast packets with an unknown address to all SMs. This can significantly reduce downlink throughput. (0) - Drop unknown unicast packets. (1) - Forward unknown unicast packets to all SMs.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

berModSelect 1.3.6.1.4.1.161.19.3.1.1.215
The modulation the AP generates BER at. 0 for QPSK, 1 for 16-QAM, 2 for 64-QAM, and 3 for 256-QAM.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER qpsk(0), qam-16(1), qam-64(2), qam-256(3)  

remoteSpectrumAnalyzerScanBandwidth 1.3.6.1.4.1.161.19.3.1.1.216
Scanning Bandwidth used for the Remote Spectrum Analyzer. Only available on PMP 450.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER bandwidth5MHz(0), bandwidth10MHz(1), bandwidth20MHz(2)  

multicastVCDataRate 1.3.6.1.4.1.161.19.3.1.1.217
The data rate that is used for the Multicast VC. 8X and MIMO-A are currently for engineering only.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), rate2XmimoB(5), rate4XmimoB(7), rate6XmimoB(8), rate8XmimoB(9), rate1XmimoA(4), rate2XmimoA(10), rate4XmimoA(11), rate6XmimoA(12)  

dlnkMcastCIR 1.3.6.1.4.1.161.19.3.1.1.218
Downlink Multicast CIR (kbps)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

multicastRetryCount 1.3.6.1.4.1.161.19.3.1.1.219
Multicast Repeat Count : Range 0 - 2. For APs.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

apConfigAdjacentChanSupport 1.3.6.1.4.1.161.19.3.1.1.220
Used to enable or disable adjacent channel support.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

pmp430InteropMode 1.3.6.1.4.1.161.19.3.1.1.221
When the AP talks to a PMP 430 it can do so in either MIMO-A or SISO mode. 0 = MIMO-A 1 = SISO Only applies to PMP 450 AP at 5 GHz. By default in 13.2 the AP talks in MIMO-A to PMP 430 SISO SMs. Setting this to a 1 will enable SISO mode to PMP 430 SISO SMs, as it was in 13.1.3 and before.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER mimoa(0), siso(1)  

framePeriod 1.3.6.1.4.1.161.19.3.1.1.223
Changes frame period to 2.5 ms or 5ms. Note: If set to 5 ms, only SM/BHS from 13.3 and onward will be able to register. Only on PMP and PTP 450. Not available in all regions.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER twoPointFiveMs(0), fiveMs(1)  

enableRadiusDynAuth 1.3.6.1.4.1.161.19.3.1.1.224
This option can be used to enable Radius Dynamic Authorization Extensions.Both CoA, which change the SM config parameters from the Radius server while an SM is already in session and Disconnect Message are supported. This option will only be used if Authentication mode is set to Radius AAA. 0 - Disable Radius Dynamic Authorization Extension. 1 - Enable Radius Dynamic Authorization Extension.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disableDynAuth(0), enableDynAuth(1)  

pmp430SMRegistration 1.3.6.1.4.1.161.19.3.1.1.225
Option to allow/disallow 430 SMs to register to this AP. When disabled 430 SMs registrations will be rejected. This option applies only to PMP 450i/450 5 GHz APs.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER deny(0), allow(1)  

disableAuthForICCSM 1.3.6.1.4.1.161.19.3.1.1.226
Bypass Authentication for ICC SMs
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

onlyAllowPMP450iSMRegistration 1.3.6.1.4.1.161.19.3.1.1.228
Option to limit SM registration to only allow PMP 450i devices or allow all devices (450i/450/430) to register. PMP 430 SM registration can be further limited by the pmp430SMRegistration OID if desired. Setting this to only450i will force an Auth Fail registration failure when a PMP 450 or PMP 430 SM device tries to register. This option only applies to PMP 450i AP devices.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER only450i(0), all(1)  

pmp450430LegacyMode 1.3.6.1.4.1.161.19.3.1.1.229
Option to put the PMP 450i into a Legacy mode for communicating with PMP 450 SMs running SW older than 13.3 and PMP 430 SMs running SW older than 13.4.1. Enabling this option will have an impact on sector throughput performance so should only be enabled to allow upgrading of the mixed sector. This option only applies to PMP 450i AP devices.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

pagerRejectFilterSelect 1.3.6.1.4.1.161.19.3.1.1.230
Enable or disable the Pager filter which can filter out Pager signals interfering in the 900 MHz band. NOTE: Frequencies 920 MHz and above will not work when enabled. Only applicable to 900 MHz devices.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

freeRunGPSSyncBypass 1.3.6.1.4.1.161.19.3.1.1.231
Enable to allow Free Run to begin immediately after radio bootup. Normally, Free Run is only allowed after GPS sync has been established at least once, then lost.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

useAPManagementVIDForICCSM 1.3.6.1.4.1.161.19.3.1.1.232
When enabled, SM connected via ICC uses APs MVID instead of its own.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

frameAlignmentLegacyMode 1.3.6.1.4.1.161.19.3.1.1.233
Option to adjust the frame alignment for compatibility with different GPS sync sources and software versions. Please see user guide for more information. Not applicable to 3 GHz radios running with 5ms frame.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER off(0), mode1(1), mode2(2)  

whispRegStatus 1.3.6.1.4.1.161.19.3.1.2.4
This shows the registration status of a link.[This variable is deprecated, please refer whispBoxLink OIDs]
Status: obsolete Access: read-only
OBJECT-TYPE    
  DisplayString  

linkTestLUID 1.3.6.1.4.1.161.19.3.1.2.1.1
LUID selection for Link Test. Valid range: 2-255. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER  

linkTestDuration 1.3.6.1.4.1.161.19.3.1.2.1.2
Duration for the Link Test. Valid range: 2-10 seconds. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER  

linkTestAction 1.3.6.1.4.1.161.19.3.1.2.1.3
Setting value 1 will initiate link test. Note that trying to set 0 will not stop the test. In fact it will return an error message. The value of 0 just indicates the idle state meaning no test is running or the current test is done. That's why the word stopped is used and not the action verb stop. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER stopped(0), start(1)  

linkTestPktLength 1.3.6.1.4.1.161.19.3.1.2.1.4
Packet length for Link Test. Valid range: 64-1714 bytes. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER  

linkTestMode 1.3.6.1.4.1.161.19.3.1.2.1.5
Link Test Mode 0 = RF Link Test (traffic doesn't go through bridge, highest throughput) 1 = Link Test with Bridging 2 = Link Test with Bridging and MIR 3 = Extrapolated Link Test (send only a few packets measuring their quality and extrapolate out the throughput) This is an estimation of the throughput based upon the modulation, efficiency, and data slots available. It intended to provide a basic link test test without impacting service for the sector. Extrapolated Link Test is not available for FSK radios. [This Variable is deprecated. Please refer whispBoxLink OIDs]
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER rflinktest(0), linktestwithbridging(1), linktestwithbridgingandmir(2), extrapolatedlinktest(3)  

linkTestSNRCalculation 1.3.6.1.4.1.161.19.3.1.2.1.6
Enable or disable Signal to Noise Ratio (SNR) calculations during a Link Test. Enabling(1) will calulate SNR on all receiving packets. Due to load on CPU, will slightly degrade packet per second capabilities. Only applicable to GenII OFDM products and up. [This Variable is deprecated. Please refer whispBoxLink OIDs]
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER enable(1), disable(0)  

linkTestWithDualPath 1.3.6.1.4.1.161.19.3.1.2.1.7
Link Test with: 0 = Low Priority VC only 1 = High and Low Priority VCs [This variable is deprecated. Please refer whispBoxLink OIDs]
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER lowpriorityvconly(0), highandlowpriorityvcs(1)  

linkTestNumPkt 1.3.6.1.4.1.161.19.3.1.2.1.8
Number of packets to send. Valid range: 0-64 where 0 will flood the link for the duration of the test. [This variable is deprecated. Please refer whispBoxLink OIDs]
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER  

linkTestForceModulation 1.3.6.1.4.1.161.19.3.1.2.1.9
Engineering use only. Link Test with: 0 = Normal Rate Adapt algorithm 1 = Force to max modultion - No Rate Adapt Algorithm [This variable is deprecated. Please refer whispBoxLink OIDs]
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER normalRateAdapt(0), forceMaxModulation(1)  

linkTestDirection 1.3.6.1.4.1.161.19.3.1.2.1.10
Link Test Direction - Engineering Use Only 0 = default (will do bidirectional) 1 = Uplink Only 2 = Downlink Only 3 = Bi-Directional (same as 0, setting to 3 will result in setting it to 0) [This variable is deprecated. Please refer whispBoxLink OIDs]
Status: deprecated Access: read-write
OBJECT-TYPE    
  INTEGER bidirectional(0), uplinkonly(1), downlinkonly(2)  

testLUID 1.3.6.1.4.1.161.19.3.1.2.2.1
LUID number of selected unit. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

linkTestStatus 1.3.6.1.4.1.161.19.3.1.2.2.2
Status for Link Test.[This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString  

linkTestError 1.3.6.1.4.1.161.19.3.1.2.2.3
Error status of Link Test: (1) Failed to recieve handshake from remote device (2) No session is currently active. Please try again after session established. (3) Received a bad transaction ID. Please try again. (4) We werent able to send the test request to the remote device. (5) We didnt receive any results from the remote device. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString  

testDuration 1.3.6.1.4.1.161.19.3.1.2.2.4
Duration of link test.[This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

downLinkRate 1.3.6.1.4.1.161.19.3.1.2.2.5
Downlink Rate.[This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

upLinkRate 1.3.6.1.4.1.161.19.3.1.2.2.6
Uplink Rate.[This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

downLinkEff 1.3.6.1.4.1.161.19.3.1.2.2.7
Down Link Efficiency.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

maxDwnLinkIndex 1.3.6.1.4.1.161.19.3.1.2.2.8
For link test results, the maximum possible downlink efficiency percentage (always 100%).[This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

actDwnLinkIndex 1.3.6.1.4.1.161.19.3.1.2.2.9
Actual down link index.[This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

expDwnFragCount 1.3.6.1.4.1.161.19.3.1.2.2.10
Expected Fragment Count.[This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  Gauge32  

actDwnFragCount 1.3.6.1.4.1.161.19.3.1.2.2.11
Actual Fragment Count.[This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  Gauge32  

upLinkEff 1.3.6.1.4.1.161.19.3.1.2.2.12
Up link efficiency.[This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

expUpFragCount 1.3.6.1.4.1.161.19.3.1.2.2.13
Uplink expected Fragment Count.[This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  Gauge32  

actUpFragCount 1.3.6.1.4.1.161.19.3.1.2.2.14
Actual uplink Fragment Count.[This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  Gauge32  

maxUpLinkIndex 1.3.6.1.4.1.161.19.3.1.2.2.15
For link test results, the maximum possible uplink efficiency percentage (always 100%).[This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

actUpLinkIndex 1.3.6.1.4.1.161.19.3.1.2.2.16
Actual Up link index.[This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments1xDwnLinkVertical 1.3.6.1.4.1.161.19.3.1.2.2.17
Number of fragments received on down link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments2xDwnLinkVertical 1.3.6.1.4.1.161.19.3.1.2.2.18
Number of fragments received on down link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments3xDwnLinkVertical 1.3.6.1.4.1.161.19.3.1.2.2.19
Number of fragments received on down link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments4xDwnLinkVertical 1.3.6.1.4.1.161.19.3.1.2.2.20
Number of fragments received on down link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments1xUpLinkVertical 1.3.6.1.4.1.161.19.3.1.2.2.21
Number of fragments received on up link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments2xUpLinkVertical 1.3.6.1.4.1.161.19.3.1.2.2.22
Number of fragments received on up link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments3xUpLinkVertical 1.3.6.1.4.1.161.19.3.1.2.2.23
Number of fragments received on up link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments4xUpLinkVertical 1.3.6.1.4.1.161.19.3.1.2.2.24
Number of fragments received on up link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

bitErrorsCorrected1xDwnLinkVertical 1.3.6.1.4.1.161.19.3.1.2.2.25
Number of bit errors corrected on average per fragment on down link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected2xDwnLinkVertical 1.3.6.1.4.1.161.19.3.1.2.2.26
Number of bit errors corrected on average per fragment on down link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected3xDwnLinkVertical 1.3.6.1.4.1.161.19.3.1.2.2.27
Number of bit errors corrected on average per fragment on down link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected4xDwnLinkVertical 1.3.6.1.4.1.161.19.3.1.2.2.28
Number of bit errors corrected on average per fragment on down link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected1xUpLinkVertical 1.3.6.1.4.1.161.19.3.1.2.2.29
Number of bit errors corrected on average per fragment on up link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected2xUpLinkVertical 1.3.6.1.4.1.161.19.3.1.2.2.30
Number of bit errors corrected on average per fragment on up link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected3xUpLinkVertical 1.3.6.1.4.1.161.19.3.1.2.2.31
Number of bit errors corrected on average per fragment on up link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected4xUpLinkVertical 1.3.6.1.4.1.161.19.3.1.2.2.32
Number of bit errors corrected on average per fragment on up link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString  

signalToNoiseRatioDownLinkVertical 1.3.6.1.4.1.161.19.3.1.2.2.33
Estimated Signal to Noise Ratio in dB for the down link. For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

signalToNoiseRatioUpLinkVertical 1.3.6.1.4.1.161.19.3.1.2.2.34
Estimated Signal to Noise Ratio in dB for the up link. For Gen II OFDM and forward. For MIMO this is the vertical path. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments1xDwnLinkHorizontal 1.3.6.1.4.1.161.19.3.1.2.2.35
Number of fragments received on down link at 1X (QPSK). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments2xDwnLinkHorizontal 1.3.6.1.4.1.161.19.3.1.2.2.36
Number of fragments received on down link at 2X (16-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments3xDwnLinkHorizontal 1.3.6.1.4.1.161.19.3.1.2.2.37
Number of fragments received on down link at 3X (64-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments4xDwnLinkHorizontal 1.3.6.1.4.1.161.19.3.1.2.2.38
Number of fragments received on down link at 4X (256-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments1xUpLinkHorizontal 1.3.6.1.4.1.161.19.3.1.2.2.39
Number of fragments received on up link at 1X (QPSK). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments2xUpLinkHorizontal 1.3.6.1.4.1.161.19.3.1.2.2.40
Number of fragments received on up link at 2X (16-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments3xUpLinkHorizontal 1.3.6.1.4.1.161.19.3.1.2.2.41
Number of fragments received on up link at 3X (64-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

fragments4xUpLinkHorizontal 1.3.6.1.4.1.161.19.3.1.2.2.42
Number of fragments received on up link at 4X (256-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

bitErrorsCorrected1xDwnLinkHorizontal 1.3.6.1.4.1.161.19.3.1.2.2.43
Number of bit errors corrected on average per fragment on down link at 1X (QPSK). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected2xDwnLinkHorizontal 1.3.6.1.4.1.161.19.3.1.2.2.44
Number of bit errors corrected on average per fragment on down link at 2X (16-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected3xDwnLinkHorizontal 1.3.6.1.4.1.161.19.3.1.2.2.45
Number of bit errors corrected on average per fragment on down link at 3X (64-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected4xDwnLinkHorizontal 1.3.6.1.4.1.161.19.3.1.2.2.46
Number of bit errors corrected on average per fragment on down link at 4X (256-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected1xUpLinkHorizontal 1.3.6.1.4.1.161.19.3.1.2.2.47
Number of bit errors corrected on average per fragment on up link at 1X (QPSK). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected2xUpLinkHorizontal 1.3.6.1.4.1.161.19.3.1.2.2.48
Number of bit errors corrected on average per fragment on up link at 2X (16-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected3xUpLinkHorizontal 1.3.6.1.4.1.161.19.3.1.2.2.49
Engineering use only. Number of bit errors corrected on average per fragment on up link at 3X (64-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString  

bitErrorsCorrected4xUpLinkHorizontal 1.3.6.1.4.1.161.19.3.1.2.2.50
Number of bit errors corrected on average per fragment on up link at 4X (256-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString  

signalToNoiseRatioDownLinkHorizontal 1.3.6.1.4.1.161.19.3.1.2.2.51
Estimated Signal to Noise Ratio in dB for the down link. For MIMO and forward. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

signalToNoiseRatioUpLinkHorizontal 1.3.6.1.4.1.161.19.3.1.2.2.52
Estimated Signal to Noise Ratio in dB for the up link. For Gen II OFDM and forward. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

downLinkRateExtrapolated 1.3.6.1.4.1.161.19.3.1.2.2.53
Extrapolated Downlink Rate from an extrapolated link test. Extrapolated Link Test sends only a few packets over the link and extrapolates this out to what would happen on a full link test. This is an estimation of the throughput based upon the modulation, efficiency, and data slots available. It intended to provide a basic link test test without impacting service for the sector. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

upLinkRateExtrapolated 1.3.6.1.4.1.161.19.3.1.2.2.54
Extrapolated Uplink Rate from an extrapolated link test. Extrapolated Link Test sends only a few packets over the link and extrapolates this out to what would happen on a full link test. This is an estimation of the throughput based upon the modulation, efficiency, and data slots available. It intended to provide a basic link test test without impacting service for the sector. [This variable is deprecated, please refer whispBoxLink OIDs]
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER  

whispGPSStats 1.3.6.1.4.1.161.19.3.1.3.1
This shows whether the AP is synchrinized to the GPS timer.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER gpsSynchronized(1), gpsLostSync(2), generatingSync(3)  

gpsSyncSource 1.3.6.1.4.1.161.19.3.1.3.2
Source of GPS Sync Pulse.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

gpsSyncStatus 1.3.6.1.4.1.161.19.3.1.3.3
Current Live value of Sync Status.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

gpsTrackingMode 1.3.6.1.4.1.161.19.3.1.3.4
GPS tracking mode.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

gpsTime 1.3.6.1.4.1.161.19.3.1.3.5
GPS time.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

gpsDate 1.3.6.1.4.1.161.19.3.1.3.6
GPS date.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

gpsSatellitesTracked 1.3.6.1.4.1.161.19.3.1.3.7
Returns Current number of satellites GPS is tracking in string format .use gpsSatellitesTrackedInt to get the value in integer
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

gpsSatellitesVisible 1.3.6.1.4.1.161.19.3.1.3.8
Return Number of satellites GPS is seeing in string format.Use gpsSatellitesVisibleInt to get value in integer
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

gpsHeight 1.3.6.1.4.1.161.19.3.1.3.9
GPS height.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

gpsAntennaConnection 1.3.6.1.4.1.161.19.3.1.3.10
Antenna Connection status.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

gpsLatitude 1.3.6.1.4.1.161.19.3.1.3.11
GPS Latitude.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

gpsLongitude 1.3.6.1.4.1.161.19.3.1.3.12
GPS Longitude.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

gpsInvalidMsg 1.3.6.1.4.1.161.19.3.1.3.13
Number of invalid messages.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

gpsRestartCount 1.3.6.1.4.1.161.19.3.1.3.14
Number of GPS unit restarts.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

gpsReInitCount 1.3.6.1.4.1.161.19.3.1.3.15
GPS ReInit counts. The number of times we have done a complete re-initialization of the GPS device.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

gpsReceiverInfo 1.3.6.1.4.1.161.19.3.1.3.16
A textual string contains information on GPS receiver.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

gpsFreeRun 1.3.6.1.4.1.161.19.3.1.3.17
This variable is deprecated. Setting this value to false will set AutoSync. Setting this value to true will set AutoSync plus Free Run.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

autoSyncStatus 1.3.6.1.4.1.161.19.3.1.3.18
Current Live value of Sync Status. Following values represent what sources have sync. (0) No Sync (1) On-board GPS Sync (2) Timing Port/UGPS Sync (3) On-board GPS and Timing Port/UGPS Sync (4) Power Port Sync (5) On-board GPS and Power Port Sync (6) Timing Port/UGPS and Power Port Sync (7) On-board GPS, Timing Port/UGPS and Power Port Sync
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noSync(0), onBoardGPSSync(1), timingPortUGPSSync(2), onBoardGPSAndTimingPortUGPSSync(3), powrPortSync(4), onBoardGPSAndPowrPortSync(5), timingPortUGPSAndPowrPortSync(6), onBoardGPSAndTimingPortUGPSAndPowrPortSync(7)  

gpsSatellitesTrackedInt 1.3.6.1.4.1.161.19.3.1.3.19
Current number of satellites GPS is tracking in integer format.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

gpsSatellitesVisibleInt 1.3.6.1.4.1.161.19.3.1.3.20
Number of satellites the GPS sees in integer format
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

whispRegComplete 1.3.6.1.4.1.161.19.3.1.5.1.1
Signals registration complete.
Status: current Access: read-only
NOTIFICATION-TYPE    

whispRegLost 1.3.6.1.4.1.161.19.3.1.5.1.2
Signals registration lost.
Status: current Access: read-only
NOTIFICATION-TYPE    

whispRegFailure 1.3.6.1.4.1.161.19.3.1.5.1.3
Signals a registration failure has occured.
Status: current Access: read-only
NOTIFICATION-TYPE    

whispDefKeyUsed 1.3.6.1.4.1.161.19.3.1.5.1.4
Signals Default Key used for encryptiont.
Status: current Access: read-only
NOTIFICATION-TYPE    

whispGPSInSync 1.3.6.1.4.1.161.19.3.1.5.2.1
Signals a transition from not-synchronized to synchronized.
Status: current Access: read-only
NOTIFICATION-TYPE    

whispGPSOutSync 1.3.6.1.4.1.161.19.3.1.5.2.2
Signals a transition from synchronized to not-synchronized.
Status: current Access: read-only
NOTIFICATION-TYPE    

whispRadarDetected 1.3.6.1.4.1.161.19.3.1.5.3.1
Radar detected transmit stopped.
Status: current Access: read-only
NOTIFICATION-TYPE    

whispRadarEnd 1.3.6.1.4.1.161.19.3.1.5.3.2
Radar ended back to normal transmit.
Status: current Access: read-only
NOTIFICATION-TYPE    

regulatoryApCheckInvalidChanFailed 1.3.6.1.4.1.161.19.3.1.5.4.1
Regulatory Check failed for the unit due to a invalid channel for the configured region. regulatoryStatus - Text description for the failure. physAddress - the MAC address of the unit.
Status: current Access: read-only
NOTIFICATION-TYPE    

regulatoryCheckFailedNoRegionAp 1.3.6.1.4.1.161.19.3.1.5.4.2
Regulatory Check failed because a valid region has not be configured. physAddress - the MAC address of the unit.
Status: current Access: read-only
NOTIFICATION-TYPE    

regulatoryApCheckInvalidChBwFailed 1.3.6.1.4.1.161.19.3.1.5.4.3
Regulatory Check failed due to an invalid channel bandwidth for the configured region. regulatoryStatus - Text description for the failure. physAddress - the MAC address of the unit.
Status: current Access: read-only
NOTIFICATION-TYPE    

rfLinkOverloadCondition 1.3.6.1.4.1.161.19.3.1.5.5.1
AP has exceeded the preset discard percentage in the RF Downlink Direction. rfOutDiscardRate - Current discard Rate. physAddress - the MAC address of the unit.
Status: current Access: read-only
NOTIFICATION-TYPE    

whispLinkTestGroup 1.3.6.1.4.1.161.19.3.1.6.1
WHiSP APs link test group.
Status: current Access: read-only
OBJECT-GROUP    

whispApsConfigGroup 1.3.6.1.4.1.161.19.3.1.6.2
WHiSP APs configuration group.
Status: current Access: read-only
OBJECT-GROUP    

whispApsLinkTableGroup 1.3.6.1.4.1.161.19.3.1.6.3
WHiSP APs Link Table group.
Status: current Access: read-only
OBJECT-GROUP    

whispApsNotifGroup 1.3.6.1.4.1.161.19.3.1.6.4
WHiSP APs notification group.
Status: current Access: read-only
NOTIFICATION-GROUP    

whispApsFailedRegTableGroup 1.3.6.1.4.1.161.19.3.1.6.5
WHiSP APs Failed Registration Table group.
Status: current Access: read-only
OBJECT-GROUP    

whispApsFrUtlStatsIntervalLowGroup 1.3.6.1.4.1.161.19.3.1.6.7
WHiSP APs Frame Utilization Statistics group for interval of 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-GROUP    

whispApsFrUtlStatsIntervalMediumGroup 1.3.6.1.4.1.161.19.3.1.6.8
WHiSP APs Frame Utilization Statistics group for interval of 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-GROUP    

whispApsFrUtlStatsIntervalHighGroup 1.3.6.1.4.1.161.19.3.1.6.9
WHiSP APs Frame Utilization Statistics group for interval of 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-GROUP    

frUtlLowTotalDownlinkUtilization 1.3.6.1.4.1.161.19.3.1.12.1.1
Percentage of total downlink utilization in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlLowTotalUplinkUtilization 1.3.6.1.4.1.161.19.3.1.12.1.2
Percentage of total uplink utilization in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlLowTotalDownlinkSlots 1.3.6.1.4.1.161.19.3.1.12.1.3
Total downlink data slots in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlLowDownlinkLowPrioSlots 1.3.6.1.4.1.161.19.3.1.12.1.4
Number of data slots used for downlink low priority traffic in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlLowDownlinkHiPrioSlots 1.3.6.1.4.1.161.19.3.1.12.1.5
Number of data slots used for downlink high priority traffic in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlLowDownlinkBcastSlots 1.3.6.1.4.1.161.19.3.1.12.1.6
Number of data slots used for downlink broadcast and multicast traffic in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlLowDownlinkAckSlots 1.3.6.1.4.1.161.19.3.1.12.1.7
Number of data slots used for Downlink Canopy MAC Acknowledgements in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlLowDownlinkCntlMsgSlots 1.3.6.1.4.1.161.19.3.1.12.1.8
Number of data slots used for downlink registration control messages in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlLowTotalUplinkSlots 1.3.6.1.4.1.161.19.3.1.12.1.9
Total uplink data slots in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlLowUplinkLowPrioSlots 1.3.6.1.4.1.161.19.3.1.12.1.10
Number of data slots used for uplink low priority traffic in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlLowUplinkHiPrioSlots 1.3.6.1.4.1.161.19.3.1.12.1.11
Number of data slots used for uplink high priority traffic in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlLowUplinkAckSlots 1.3.6.1.4.1.161.19.3.1.12.1.12
Number of data slots used for Uplink Canopy MAC Acknowledgements in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlLowMaxDownlinkSlots 1.3.6.1.4.1.161.19.3.1.12.1.13
Maximum possible downlink data slots for a minute. This is calculated as ((Downlink slots in a frame) * (Number of frames in a second) * 60). Downlink slots in a frame depends on the frame configuration. Number of frames in a second depends on the configured frame period of 5 ms (200 frames) or 2.5 ms (400 frames). Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlLowMaxUplinkSlots 1.3.6.1.4.1.161.19.3.1.12.1.14
Maximum possible uplink data slots for a minute. This is calculated as ((Uplink slots in a frame) * (Number of frames in a second) * 60). Uplink slots in a frame depends on the frame configuration. Number of frames in a second depends on the configured frame period of 5 ms (200 frames) or 2.5 ms (400 frames). Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlLowEthInDiscards 1.3.6.1.4.1.161.19.3.1.12.1.15
Number of incoming ethernet packets discarded in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlLowEthOutDiscards 1.3.6.1.4.1.161.19.3.1.12.1.16
Number of outgoing ethernet packets discarded in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlLowRFInDiscards 1.3.6.1.4.1.161.19.3.1.12.1.17
Number of incoming radio packets discarded in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlLowRFOutDiscards 1.3.6.1.4.1.161.19.3.1.12.1.18
Number of outgoing radio packets discarded in the last 1 minute. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlMedTotalDownlinkUtilization 1.3.6.1.4.1.161.19.3.1.12.2.1
Percentage of total downlink utilization in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlMedTotalUplinkUtilization 1.3.6.1.4.1.161.19.3.1.12.2.2
Percentage of total uplink utilization in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlMedTotalDownlinkSlots 1.3.6.1.4.1.161.19.3.1.12.2.3
Total downlink data slots in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlMedDownlinkLowPrioSlots 1.3.6.1.4.1.161.19.3.1.12.2.4
Number of data slots used for downlink low priority traffic in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlMedDownlinkHiPrioSlots 1.3.6.1.4.1.161.19.3.1.12.2.5
Number of data slots used for downlink high priority traffic in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlMedDownlinkBcastSlots 1.3.6.1.4.1.161.19.3.1.12.2.6
Number of data slots used for downlink broadcast and multicast traffic in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlMedDownlinkAckSlots 1.3.6.1.4.1.161.19.3.1.12.2.7
Number of data slots used for Downlink Canopy MAC Acknowledgements in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlMedDownlinkCntlMsgSlots 1.3.6.1.4.1.161.19.3.1.12.2.8
Number of data slots used for downlink registration control messages in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlMedTotalUplinkSlots 1.3.6.1.4.1.161.19.3.1.12.2.9
Total uplink data slots in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlMedUplinkLowPrioSlots 1.3.6.1.4.1.161.19.3.1.12.2.10
Number of data slots used for uplink low priority traffic in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlMedUplinkHiPrioSlots 1.3.6.1.4.1.161.19.3.1.12.2.11
Number of data slots used for uplink high priority traffic in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlMedUplinkAckSlots 1.3.6.1.4.1.161.19.3.1.12.2.12
Number of data slots used for Uplink Canopy MAC Acknowledgements in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlMedMaxDownlinkSlots 1.3.6.1.4.1.161.19.3.1.12.2.13
Maximum possible downlink data slots for 5 minutes. This is calculated as ((Downlink slots in a frame) * (Number of frames in a second) * 5 * 60 (seconds)). Downlink slots in a frame depends on the frame configuration. Number of frames in a second depends on the configured frame period of 5 ms (200 frames) or 2.5 ms (400 frames). Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlMedMaxUplinkSlots 1.3.6.1.4.1.161.19.3.1.12.2.14
Maximum possible uplink data slots for 5 minutes. This is calculated as ((Uplink slots in a frame) * (Number of frames in a second) * 5 * 60(seconds)). Uplink slots in a frame depends on the frame configuration. Number of frames in a second depends on the configured frame period of 5 ms (200 frames) or 2.5 ms (400 frames). Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlMedEthInDiscards 1.3.6.1.4.1.161.19.3.1.12.2.15
Number of incoming ethernet packets discarded in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlMedEthOutDiscards 1.3.6.1.4.1.161.19.3.1.12.2.16
Number of outgoing ethernet packets discarded in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlMedRFInDiscards 1.3.6.1.4.1.161.19.3.1.12.2.17
Number of incoming radio packets discarded in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlMedRFOutDiscards 1.3.6.1.4.1.161.19.3.1.12.2.18
Number of outgoing radio packets discarded in the last 5 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlHighTotalDownlinkUtilization 1.3.6.1.4.1.161.19.3.1.12.3.1
Percentage of total downlink utilization in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlHighTotalUplinkUtilization 1.3.6.1.4.1.161.19.3.1.12.3.2
Percentage of total uplink utilization in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlHighTotalDownlinkSlots 1.3.6.1.4.1.161.19.3.1.12.3.3
Total downlink data slots in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlHighDownlinkLowPrioSlots 1.3.6.1.4.1.161.19.3.1.12.3.4
Number of data slots used for downlink low priority traffic in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlHighDownlinkHiPrioSlots 1.3.6.1.4.1.161.19.3.1.12.3.5
Number of data slots used for downlink high priority traffic in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlHighDownlinkBcastSlots 1.3.6.1.4.1.161.19.3.1.12.3.6
Number of data slots used for downlink broadcast and multicast traffic in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlHighDownlinkAckSlots 1.3.6.1.4.1.161.19.3.1.12.3.7
Number of data slots used for Downlink Canopy MAC Acknowledgements in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlHighDownlinkCntlMsgSlots 1.3.6.1.4.1.161.19.3.1.12.3.8
Number of data slots used for downlink registration control messages in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlHighTotalUplinkSlots 1.3.6.1.4.1.161.19.3.1.12.3.9
Total uplink data slots in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlHighUplinkLowPrioSlots 1.3.6.1.4.1.161.19.3.1.12.3.10
Number of data slots used for uplink low priority traffic in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlHighUplinkHiPrioSlots 1.3.6.1.4.1.161.19.3.1.12.3.11
Number of data slots used for uplink high priority traffic in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlHighUplinkAckSlots 1.3.6.1.4.1.161.19.3.1.12.3.12
Number of data slots used for Uplink Canopy MAC Acknowledgements in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlHighMaxDownlinkSlots 1.3.6.1.4.1.161.19.3.1.12.3.13
Maximum possible downlink data slots for 15 minutes. This is calculated as ((Downlink slots in a frame) * (Number of frames in a second) * 15 * 60(seconds)). Downlink slots in a frame depends on the frame configuration. Number of frames in a second depends on the configured frame period of 5 ms (200 frames) or 2.5 ms (400 frames). Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlHighMaxUplinkSlots 1.3.6.1.4.1.161.19.3.1.12.3.14
Maximum possible uplink data slots for 15 minutes. This is calculated as ((Uplink slots in a frame) * (Number of frames in a second) * 15 * 60(seconds)). Uplink slots in a frame depends on the frame configuration. Number of frames in a second depends on the configured frame period of 5 ms (200 frames) or 2.5 ms (400 frames). Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlHighEthInDiscards 1.3.6.1.4.1.161.19.3.1.12.3.15
Number of incoming ethernet packets discarded in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlHighEthOutDiscards 1.3.6.1.4.1.161.19.3.1.12.3.16
Number of outgoing ethernet packets discarded in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlHighRFInDiscards 1.3.6.1.4.1.161.19.3.1.12.3.17
Number of incoming radio packets discarded in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

frUtlHighRFOutDiscards 1.3.6.1.4.1.161.19.3.1.12.3.18
Number of outgoing radio packets discarded in the last 15 minutes. Only supported for PMP and PTP 450 AP and Backhauls.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

regCount 1.3.6.1.4.1.161.19.3.1.7.1
Number of registered SMs.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

gpsStatus 1.3.6.1.4.1.161.19.3.1.7.2
GPS status.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

radioSlicingAp 1.3.6.1.4.1.161.19.3.1.7.3
The variable is deprecated.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER  

radioTxGainAp 1.3.6.1.4.1.161.19.3.1.7.4
Radio transmit gain setting.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dataSlotDwn 1.3.6.1.4.1.161.19.3.1.7.5
Number of data slot down.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dataSlotUp 1.3.6.1.4.1.161.19.3.1.7.6
Number of data slot up.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

dataSlotUpHi 1.3.6.1.4.1.161.19.3.1.7.7
Number of high priority data slot up.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

upLnkAckSlot 1.3.6.1.4.1.161.19.3.1.7.8
Uplink ack slots.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

upLnkAckSlotHi 1.3.6.1.4.1.161.19.3.1.7.9
Hige priority uplink ack slots.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

dwnLnkAckSlot 1.3.6.1.4.1.161.19.3.1.7.10
Downlink ack slots.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

dwnLnkAckSlotHi 1.3.6.1.4.1.161.19.3.1.7.11
Hige priority downlink ack slots.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

numCtrSlot 1.3.6.1.4.1.161.19.3.1.7.12
Number of contention slots.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

numCtrSlotHi 1.3.6.1.4.1.161.19.3.1.7.13
High priority control slot.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

dfsStatus 1.3.6.1.4.1.161.19.3.1.7.14
Dynamic frequency shifting status.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

dfsStatusPrimary 1.3.6.1.4.1.161.19.3.1.7.15
Dynamic frequency shifting status for Primary Channel.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

dfsStatusAlt1 1.3.6.1.4.1.161.19.3.1.7.16
Dynamic frequency shifting status for Alternate Channel 1
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

dfsStatusAlt2 1.3.6.1.4.1.161.19.3.1.7.17
Dynamic frequency shifting status for Alternate Channel 2
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

maxRegSMCount 1.3.6.1.4.1.161.19.3.1.7.18
Maximum number of unique Subscriber Modules registered with this AP at once
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

systemTime 1.3.6.1.4.1.161.19.3.1.7.19
Displays the system time of the unit
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

lastNTPTime 1.3.6.1.4.1.161.19.3.1.7.20
Displays the last NTP time acquired by the AP
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

regulatoryStatus 1.3.6.1.4.1.161.19.3.1.7.21
The current status of the regulatory check on the AP.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

dhcpRlyAgntStat-reqRecvd 1.3.6.1.4.1.161.19.3.1.7.22
Number of DHCP Requests received by the DHCP Relay.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dhcpRlyAgntStat-reqRelayed 1.3.6.1.4.1.161.19.3.1.7.23
Number of DHCP Requests relayed by the DHCP Relay.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dhcpRlyAgntStat-reqDiscards 1.3.6.1.4.1.161.19.3.1.7.24
Number of DHCP Requests discarded by the DHCP Relay.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dhcpRlyAgntStat-respRecvd 1.3.6.1.4.1.161.19.3.1.7.25
Number of DHCP Replies received by the DHCP Relay.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dhcpRlyAgntStat-respRelayed 1.3.6.1.4.1.161.19.3.1.7.26
Number of DHCP Replies relayed by the DHCP Relay.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dhcpRlyAgntStat-respDiscards 1.3.6.1.4.1.161.19.3.1.7.27
Number of DHCP Replies discarded by the DHCP Relay.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dhcpRlyAgntStat-untrustedDiscards 1.3.6.1.4.1.161.19.3.1.7.28
Number of untrusted messages discarded by the DHCP Relay.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dhcpRlyAgntStat-maxHopDiscards 1.3.6.1.4.1.161.19.3.1.7.29
Number of messages discarded by the DHCP Relay due to exceeded max hop.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dhcpRlyAgntStat-pktTooBig 1.3.6.1.4.1.161.19.3.1.7.30
Number of messages forwarded without relay information by the DHCP Relay due to relay information exceeding max message size.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dhcpRlyAgntStat-invalidGiaddrDiscards 1.3.6.1.4.1.161.19.3.1.7.31
Number of messages discarded by the DHCP Relay due to invalid giaddr in packet.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

regFailureCount 1.3.6.1.4.1.161.19.3.1.7.32
The Total number or Registration Grant Failures.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

ntpLogSNMP 1.3.6.1.4.1.161.19.3.1.7.33
NTP Log
Status: current Access: read-only
OBJECT-TYPE    
  EventString  

uGPSPowerStatus 1.3.6.1.4.1.161.19.3.1.7.34
Current UGPS Power Status (UGPS capable APs only).
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

rfOutDiscardRate 1.3.6.1.4.1.161.19.3.1.7.35
Percentage of OutDiscards on the RF link (RF Overload %) in the last minute.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

autoUpdateGlobalStatus 1.3.6.1.4.1.161.19.3.1.7.36
Status of the Auto-Update Command
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

currentRadioFreqCarrier 1.3.6.1.4.1.161.19.3.1.7.37
Returns the current operating frequency of the AP. Units vary by platform: FSK 5.2, 5.4, 5.7 GHz: OID returns MHz FSK 900 MHz, 2.4 GHz: OID returns 100's of KHz OFDM: OID returns 10's of KHz
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

ntpDomainNameAppend 1.3.6.1.4.1.161.19.3.1.9.1
Select whether to append the configured management domain name to the configured trap names. For example, if dnsMgmtDomainName is set to 'example.com', ntpServer is set to 'ntp', and ntpDomainNameAppend is set to appendDomain, the ntpServer name used would be 'ntp.example.com'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disableDomain(0), appendDomain(1)  

ntpServer1 1.3.6.1.4.1.161.19.3.1.9.2
NTP Server 1 Address. Format is either an IP address or DNS name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

ntpServer2 1.3.6.1.4.1.161.19.3.1.9.3
NTP Server 2 Address. Format is either an IP address or DNS name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

ntpServer3 1.3.6.1.4.1.161.19.3.1.9.4
NTP Server 3 Address. Format is either an IP address or DNS name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

dhcprDomainNameAppend 1.3.6.1.4.1.161.19.3.1.9.5
Select whether to append the configured management domain name to the configured trap names. For example, if dnsMgmtDomainName is set to 'example.com', dhcprServer is set to 'dhcpr', and dhcprDomainNameAppend is set to appendDomain, the dhcprServer name used would be 'dhcpr.example.com'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disableDomain(0), appendDomain(1)  

dhcprServer 1.3.6.1.4.1.161.19.3.1.9.6
DHCP Server IP which will be used for forwarding DHCP messages by the DHCP Relay Agent in the MultiPoint AP. - Format is either an IP address or DNS name. - Default is 255.255.255.255 (broadcast).
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

authDomainNameAppend 1.3.6.1.4.1.161.19.3.1.9.7
Select whether to append the configured management domain name to the configured trap names. For example, if dnsMgmtDomainName is set to 'example.com', authServer1 is set to 'auth1', and authDomainNameAppend is set to appendDomain, the authServer1 name used would be 'auth1.example.com'.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disableDNSDomain(0), enableDNSDomain(1)  

authServer1 1.3.6.1.4.1.161.19.3.1.9.8
Authentication Server 1. Format is either an IP address or DNS name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

authServer2 1.3.6.1.4.1.161.19.3.1.9.9
Authentication Server 2. Format is either an IP address or DNS name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

authServer3 1.3.6.1.4.1.161.19.3.1.9.10
Authentication Server 3. Format is either an IP address or DNS name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

authServer4 1.3.6.1.4.1.161.19.3.1.9.11
Authentication Server 4. Format is either an IP address or DNS name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

authServer5 1.3.6.1.4.1.161.19.3.1.9.12
Authentication Server 5. Format is either an IP address or DNS name.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString  

acctDomainNameAppend 1.3.6.1.4.1.161.19.3.1.9.13
Obsoleted. Use whispApsDNS.authDomainNameAppend.
Status: obsolete Access: read-write
OBJECT-TYPE    
  INTEGER disableDomain(0), appendDomain(1)  

clearLinkTableStats 1.3.6.1.4.1.161.19.3.1.11.1
Setting this to a nonzero value will clear the link table stats.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

whispApsRFConfigRadios 1.3.6.1.4.1.161.19.3.1.10.1
Radio configuration table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WhispApsRFConfigRadioEntry

whispApsRFConfigRadioEntry 1.3.6.1.4.1.161.19.3.1.10.1.1
Radio configuration entry.
Status: current Access: not-accessible
OBJECT-TYPE    
  WhispApsRFConfigRadioEntry  

radioFreqCarrier 1.3.6.1.4.1.161.19.3.1.10.1.1.1
RF Frequency. Please see the whispBoxRFPhysicalRadioFrequencies SNMP table for a list of available frequencies. 0: wired.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER wired(0)  

radioDownlinkPercent 1.3.6.1.4.1.161.19.3.1.10.1.1.2
This is the percentage of frame data space allocated for downlink. Various radio platforms and regions will have different allowable downlink percentages.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..99  

radioMaxRange 1.3.6.1.4.1.161.19.3.1.10.1.1.3
Access point max range.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

radioControlSlots 1.3.6.1.4.1.161.19.3.1.10.1.1.4
Total number of contention slots for HW Scheduling Point-to-Mulitpoint mode (Not applicable for PtoP radios). For PMP 450 the minimum is 1 control slot, others minimum is zero. Maximum contention slots is 15.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

radioTransmitOutputPower 1.3.6.1.4.1.161.19.3.1.10.1.1.5
Transmitter output power.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER  

radioColorCode 1.3.6.1.4.1.161.19.3.1.10.1.1.6
Color code.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..254  

whispLinkTable 1.3.6.1.4.1.161.19.3.1.4
List of link test results
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WhispLinkEntry

whispLinkEntry 1.3.6.1.4.1.161.19.3.1.4.1
List of link test results
Status: current Access: not-accessible
OBJECT-TYPE    
  WhispLinkEntry  

linkLUID 1.3.6.1.4.1.161.19.3.1.4.1.1
LUID number.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 2..239  

linkDescr 1.3.6.1.4.1.161.19.3.1.4.1.2
A textual string containing information about the unit. This string should include the name of the manufacturer, the product name and the version of the hardware interface.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

linkPhysAddress 1.3.6.1.4.1.161.19.3.1.4.1.3
Physical Address of the unit.
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

linkMtu 1.3.6.1.4.1.161.19.3.1.4.1.4
The size of the largest datagram which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

linkSpeed 1.3.6.1.4.1.161.19.3.1.4.1.5
An estimate of the interface's current bandwidth in bits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

linkOperStatus 1.3.6.1.4.1.161.19.3.1.4.1.6
This variable is not used.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER up(1), down(2), testing(3)  

linkInOctets 1.3.6.1.4.1.161.19.3.1.4.1.7
The total number of octets received on the interface, including framing characters.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkInUcastPkts 1.3.6.1.4.1.161.19.3.1.4.1.8
The number of subnetwork-unicast packets delivered to a higher-layer protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkInNUcastPkts 1.3.6.1.4.1.161.19.3.1.4.1.9
The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkInDiscards 1.3.6.1.4.1.161.19.3.1.4.1.10
The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkInError 1.3.6.1.4.1.161.19.3.1.4.1.11
The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkInUnknownProtos 1.3.6.1.4.1.161.19.3.1.4.1.12
The number of packets received via the interface which were discarded because of an unknown or unsupported protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkOutOctets 1.3.6.1.4.1.161.19.3.1.4.1.13
The total number of octets transmitted out of the interface, including framing characters.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkOutUcastPkts 1.3.6.1.4.1.161.19.3.1.4.1.14
The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkOutNUcastPkts 1.3.6.1.4.1.161.19.3.1.4.1.15
The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkOutDiscards 1.3.6.1.4.1.161.19.3.1.4.1.16
The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkOutError 1.3.6.1.4.1.161.19.3.1.4.1.17
The number of outbound packets that could not be transmitted because of errors.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkOutQLen 1.3.6.1.4.1.161.19.3.1.4.1.18
Number of packets in output packet queue.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

linkSessState 1.3.6.1.4.1.161.19.3.1.4.1.19
Current operational state of an interface. 0 = Idle 1 = In Session 2 = Clearing 3 = Re-registration downlink reset 4 = Authentication Challenge 5 = Registering 6 = Not in use
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER idle(0), inSession(1), clearing(2), reRegDnRst(3), authChal(4), registering(5), notInUse(6)  

linkESN 1.3.6.1.4.1.161.19.3.1.4.1.20
Link Electronic serial number. It is MAC address.
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

linkRSSI 1.3.6.1.4.1.161.19.3.1.4.1.21
The average RSSI reading of all packets received from an SM. Applicable to FSK radios only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

linkAveJitter 1.3.6.1.4.1.161.19.3.1.4.1.22
The average Jitter reading of all packets received from an SM. Applicable to FSK radios only.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..15  

linkLastJitter 1.3.6.1.4.1.161.19.3.1.4.1.23
Last jitter value. Applicable to FSK radios only.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..15  

linkAirDelay 1.3.6.1.4.1.161.19.3.1.4.1.24
The current round trip air delay in bits measured between the AP and SM.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

linkRegCount 1.3.6.1.4.1.161.19.3.1.4.1.25
The number of times an SM has registered to an AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

linkReRegCount 1.3.6.1.4.1.161.19.3.1.4.1.26
The number of times an SM has tried to register with the AP while it still has an active session with the AP.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

linkTimeOut 1.3.6.1.4.1.161.19.3.1.4.1.27
Link time out.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

linkLastRSSI 1.3.6.1.4.1.161.19.3.1.4.1.28
The last RSSI reading of all packets received from an SM. Applicable to FSK radios only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sessionCount 1.3.6.1.4.1.161.19.3.1.4.1.29
How many times has this mac been in/out of session.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

softwareVersion 1.3.6.1.4.1.161.19.3.1.4.1.30
The software version of registered SM.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

softwareBootVersion 1.3.6.1.4.1.161.19.3.1.4.1.31
The software boot version of registered SM.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

fpgaVersion 1.3.6.1.4.1.161.19.3.1.4.1.32
The FPGA version of registered SM.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

linkSiteName 1.3.6.1.4.1.161.19.3.1.4.1.33
The site name of the registered SM.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

avgPowerLevel 1.3.6.1.4.1.161.19.3.1.4.1.34
The average power level of registered SM. For systems that support power control, this value can read 'NA' when the AP adjusts the transmit power of a SM until new packets are received from the SM with it transmitting at its new power level. For MIMO this is the combined receive power.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

lastPowerLevel 1.3.6.1.4.1.161.19.3.1.4.1.35
The last power level of registered SM. For MIMO radios this is the combined receive power.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

sesDownLinkRate 1.3.6.1.4.1.161.19.3.1.4.1.36
Down link rate.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sesDownLinkLimit 1.3.6.1.4.1.161.19.3.1.4.1.37
Down link limit.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sesUpLinkRate 1.3.6.1.4.1.161.19.3.1.4.1.38
Uplink rate.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sesUpLinkLimit 1.3.6.1.4.1.161.19.3.1.4.1.39
Uplink limit.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

adaptRate 1.3.6.1.4.1.161.19.3.1.4.1.40
Adapt rate of registered SM.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

sesLoUpCIR 1.3.6.1.4.1.161.19.3.1.4.1.41
Low priority up link CIR.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sesLoDownCIR 1.3.6.1.4.1.161.19.3.1.4.1.42
Low priority down link CIR.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sesHiUpCIR 1.3.6.1.4.1.161.19.3.1.4.1.43
High priority up link CIR.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

sesHiDownCIR 1.3.6.1.4.1.161.19.3.1.4.1.44
High priority down link CIR.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

platformVer 1.3.6.1.4.1.161.19.3.1.4.1.45
Platform Version.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

smSessionTmr 1.3.6.1.4.1.161.19.3.1.4.1.46
SM session uptime
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

smSessionSeqNumMismatch 1.3.6.1.4.1.161.19.3.1.4.1.47
The count of how many sequence number mismatch between the AP/BHM and the SM/BHS during the authentication challenge and authentication response messages. This status is only valid in a system where encryption is enabled and no authentication server is configured.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

dataVCNum 1.3.6.1.4.1.161.19.3.1.4.1.48
The normal priority Data VC number in use for this link.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

hiPriQEn 1.3.6.1.4.1.161.19.3.1.4.1.49
Returns whether High Priority channel is enabled. On P7/P8 devices will return 0 always. Use p7p8HiPriQEn OID for P7/P8 radios.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

dataVCNumHiQ 1.3.6.1.4.1.161.19.3.1.4.1.50
The high priority Data VC number in use for this link, if any. If 0, no High Priority channel is in place.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

linkInOctetsHiQ 1.3.6.1.4.1.161.19.3.1.4.1.51
The total number of octets received on High Priority Queue, including framing characters.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkInUcastPktsHiQ 1.3.6.1.4.1.161.19.3.1.4.1.52
The number of subnetwork-unicast packets on High Priority Queue delivered to a higher-layer protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkInNUcastPktsHiQ 1.3.6.1.4.1.161.19.3.1.4.1.53
The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets on High Priority Queue delivered to a higher-layer protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkInDiscardsHiQ 1.3.6.1.4.1.161.19.3.1.4.1.54
The number of inbound packets on High Priority Queue which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkInErrorHiQ 1.3.6.1.4.1.161.19.3.1.4.1.55
The number of inbound packets on High Priority Queue that contained errors preventing them from being deliverable to a higher-layer protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkInUnknownProtosHiQ 1.3.6.1.4.1.161.19.3.1.4.1.56
The number of packets received on High Priority Queue via the interface which were discarded because of an unknown or unsupported protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkOutOctetsHiQ 1.3.6.1.4.1.161.19.3.1.4.1.57
The total number of octets on High Priority Queue transmitted out of the interface, including framing characters.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkOutUcastPktsHiQ 1.3.6.1.4.1.161.19.3.1.4.1.58
The total number of packets on High Priority Queue that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkOutNUcastPktsHiQ 1.3.6.1.4.1.161.19.3.1.4.1.59
The total number of packets on High Priority Queue that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkOutDiscardsHiQ 1.3.6.1.4.1.161.19.3.1.4.1.60
The number of outbound packets on High Priority Queue which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkOutErrorHiQ 1.3.6.1.4.1.161.19.3.1.4.1.61
The number of outbound packets on High Priority Queue that could not be transmitted because of errors.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vcQOverflow 1.3.6.1.4.1.161.19.3.1.4.1.62
The number of packets dropped due to Queue overflow on VC.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

vcQOverflowHiQ 1.3.6.1.4.1.161.19.3.1.4.1.63
The number of packets dropped due to Queue overflow on High Priority VC, if enabled.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

p7p8HiPriQEn 1.3.6.1.4.1.161.19.3.1.4.1.64
Returns whether P7/P8 hi priority channel is enabled. On non-P7/P8 devices will return 0 always.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disabled-or-NA(0), enabled(1)  

p7p8HiPriQ 1.3.6.1.4.1.161.19.3.1.4.1.65
Hi Priority Queue statistics for P7 or P8 radios, if enabled. If not enabled, or not a P7 or P8, will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkAirDelayns 1.3.6.1.4.1.161.19.3.1.4.1.66
The current round trip air delay in nanoseconds measured between the AP and SM.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

linkQualityAPData 1.3.6.1.4.1.161.19.3.1.4.1.67
Engineering use only. The current link quality of the SM's data from the AP. This is relative to the current modulation rate (1X, 2X, 3X, etc).
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

linkManagementIP 1.3.6.1.4.1.161.19.3.1.4.1.69
Management IP Address of the unit. 0 indicates SM is not publically addressable.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

linkFragmentsReceived1XVertical 1.3.6.1.4.1.161.19.3.1.4.1.70
Engineering use only. Number of fragments received in 1x (QPSK) modulation. For GenII OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkFragmentsReceived2XVertical 1.3.6.1.4.1.161.19.3.1.4.1.71
Engineering use only. Number of fragments received in 2x (16-QAM) modulation. For GenII OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkFragmentsReceived3XVertical 1.3.6.1.4.1.161.19.3.1.4.1.72
Engineering use only. Number of fragments received in 3x (64-QAM) modulation. For GenII OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkFragmentsReceived4XVertical 1.3.6.1.4.1.161.19.3.1.4.1.73
Engineering use only. Number of fragments received in 4x (256-QAM) modulation. For GenII OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

signalToNoiseRatioVertical 1.3.6.1.4.1.161.19.3.1.4.1.74
Estimate of the receive signal to noise ratio in dB. For GenII OFDM and forward. For MIMO this is the vertical path.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

radiusReplyMsg 1.3.6.1.4.1.161.19.3.1.4.1.75
The RADIUS Reply-Msg populated for the SM. This is only valid when using a backen AAA server.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

autoUpdateStatus 1.3.6.1.4.1.161.19.3.1.4.1.76
status of the auto update process
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

radiusFramedIPAddress 1.3.6.1.4.1.161.19.3.1.4.1.77
This Attribute indicates the IP address to be configured for the SM management interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

radiusFramedIPNetmask 1.3.6.1.4.1.161.19.3.1.4.1.78
This Attribute indicates the netmask to be configured for the SM management interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

radiusDefaultGateway 1.3.6.1.4.1.161.19.3.1.4.1.79
This Attribute indicates the default gateway to be configured for the SM management interface.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

linkFragmentsReceived1XHorizontal 1.3.6.1.4.1.161.19.3.1.4.1.80
Engineering use only. Number of fragments received in 1x (QPSK) modulation. For MIMO only. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkFragmentsReceived2XHorizontal 1.3.6.1.4.1.161.19.3.1.4.1.81
Engineering use only. Number of fragments received in 2x (16-QAM) modulation. For MIMO only. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkFragmentsReceived3XHorizontal 1.3.6.1.4.1.161.19.3.1.4.1.82
Engineering use only. Number of fragments received in 3x (64-QAM) modulation. For MIMO only. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

linkFragmentsReceived4XHorizontal 1.3.6.1.4.1.161.19.3.1.4.1.83
Engineering use only. Number of fragments received in 4x (256-QAM) modulation. For MIMO only. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

signalToNoiseRatioHorizontal 1.3.6.1.4.1.161.19.3.1.4.1.84
Estimate of the receive signal to noise ratio in dB. MIMO radios only. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

linkSignalStrengthRatio 1.3.6.1.4.1.161.19.3.1.4.1.86
Signal Strength Ratio in dB is the power received by the vertical antenna input (dB) - power received by the horizontal antenna input (dB). MIMO radios only.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

linkRadioDbmHorizontal 1.3.6.1.4.1.161.19.3.1.4.1.87
Receive power level of the horizontal antenna in dBm. MIMO radios only.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

linkRadioDbmVertical 1.3.6.1.4.1.161.19.3.1.4.1.88
Receive power level of the vertical antenna in dBm. MIMO radios only.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

maxSMTxPwr 1.3.6.1.4.1.161.19.3.1.4.1.89
Returns whether SM is transmitting at its configured max power level.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

productType 1.3.6.1.4.1.161.19.3.1.4.1.90
Returns which type of product the SM is. PMP 450 APs only.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), pmp450MIMOOFDM(1), pmp430SISOOFDM(2), pmp450SISOOFDM(3), ptp450(4), pmp450i(5), ptp450i(6)  

linkAdaptRateLowPri 1.3.6.1.4.1.161.19.3.1.4.1.91
The current transmitting rate of the low priority VC. 0 : SM is not in session 1 : 1X QPSK SISO 2 : 2X 16-QAM SISO or QPSK MIMO 3 : 3X 64-QAM SISO 4 : 4X 256-QAM SISO or 16-QAM MIMO 6 : 6X 64-QAM MIMO 8 : 8X 256-QAM MIMO
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noSession(0), rate1X(1), rate2X(2), rete3X(3), rate4X(4), rate6X(6), rate8X(8)  

linkAdaptRateHighPri 1.3.6.1.4.1.161.19.3.1.4.1.92
The current transmitting rate of the high priority VC. -1 : High Priority Channel not configured 0 : SM is not in session 1 : 1X QPSK SISO 2 : 2X 16-QAM SISO or QPSK MIMO 3 : 3X 64-QAM SISO 4 : 4X 256-QAM SISO or 16-QAM MIMO 6 : 6X 64-QAM MIMO 8 : 8X 256-QAM MIMO
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER noHighPriorityChannel(-1), noSession(0), rate1X(1), rate2X(2), rete3X(3), rate4X(4), rate6X(6), rate8X(8)  

avgPowerLevelInt 1.3.6.1.4.1.161.19.3.1.4.1.93
The average power level of registered SM as Integer. For systems that support power control, this value can read '0' when the AP adjusts the transmit power of a SM until new packets are received from the SM with it transmitting at its new power level. For MIMO this is the combined receive power.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mimoPowerLevelVertical 1.3.6.1.4.1.161.19.3.1.4.1.94
For MIMO radios, the Vertical power level of registered SM as Integer. The Vertical Power (+45) level in case of 2.4GHz Dual slant MIMO
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

mimoPowerLevelHorizontal 1.3.6.1.4.1.161.19.3.1.4.1.95
For MIMO radios, the Horizontal power level of registered SM as Integer. The Horizontal Power(-45) level in case of 2.4GHz Dual slant MIMO
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER  

linkSwVersion 1.3.6.1.4.1.161.19.3.1.4.1.96
The swversion of registered SM, to be used internally.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

whispFailedRegTable 1.3.6.1.4.1.161.19.3.1.8
List of link test results
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    WhispFailedRegEntry

whispFailedRegEntry 1.3.6.1.4.1.161.19.3.1.8.1
List of Failed ESNs
Status: current Access: not-accessible
OBJECT-TYPE    
  WhispFailedRegEntry  

regGrantReason 1.3.6.1.4.1.161.19.3.1.8.1.1
The registration failure reason
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER reggnt-valid(0), reggnt-outofrange(1), reggnt-nolUIDS(2), reggnt-rerange(3), reggnt-authfail(4), reggnt-encryptfail(5), reggnt-poweradjust(6), reggnt-novcs(7), reggnt-failvcreserve(8), reggnt-failvcactive(9), reggnt-failhivcdata(10), reggnt-failsmlimit(11), reggnt-fail95orabove(12)  

regFailESN 1.3.6.1.4.1.161.19.3.1.8.1.2
The ESN that failed to register
Status: current Access: read-only
OBJECT-TYPE    
  PhysAddress  

regFailTime 1.3.6.1.4.1.161.19.3.1.8.1.3
The number of ticks that occurred when the ESN failed to register
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

regFailSeqNum 1.3.6.1.4.1.161.19.3.1.8.1.4
The sequence when the register failure was given.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

regFailReasonText 1.3.6.1.4.1.161.19.3.1.8.1.5
The text description of the failure.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString  

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor