Unisphere-Data-ERX-System-MIB

File: Unisphere-Data-ERX-System-MIB.mib (70543 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	SNMPv2-CONF
IF-MIB	Unisphere-Data-MIBs	Unisphere-Data-TC

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	NOTIFICATION-TYPE
Integer32	Unsigned32	TimeTicks
TEXTUAL-CONVENTION	DisplayString	TruthValue
DateAndTime	MODULE-COMPLIANCE	OBJECT-GROUP
NOTIFICATION-GROUP	InterfaceIndexOrZero	usDataMibs
UsdEnable

Defined Types

UsdTimingSelector
The system timing selector. A value of 1 corresponds to the primary timing selector. A value of 2 corresponds to the secondary timing selector. A value of 3 corresponds to the tertiary timing selector. A value of 4 indicates an error with the timing selector.
TEXTUAL-CONVENTION
	INTEGER	1..4

UsdTimingSourceType
The set of selectable timing source types. The timing source type determines the timing source parameters.
TEXTUAL-CONVENTION
	INTEGER	timingInterfaceIfIndex(1), timingInternal(2), timingLine(3)

UsdTimingSourceLineType
The set of choices for line type timing.
TEXTUAL-CONVENTION
	INTEGER	timingSourceLineUndefined(0), timingSourceLineE1PortA(1), timingSourceLineE1PortB(2), timingSourceLineT1PortA(3), timingSourceLineT1PortB(4)

UsdSysCardType
The type of card in a system slot: unknown Unknown type. srp Switch/Route Processor. ct3 Channelized T3. oc3 OC-3 (SONET/SDH). ut3Atm Unchannelized T3 (ATM service). ut3Frame Unchannelized T3 (Frame service). ue3Atm Unchannelized E3 (ATM service). ue3Frame Uncahnnelized E3 (Frame service). ce1 Channelized E1. ct1 Channelized T1. dpfe Dual Port Fast Ethernet. oc12Pos OC-12 (POS/SDH). oc12Atm OC-12 (ATM service). oc3Pos Quad OC-3 (POS/SDH). oc3Atm Quad OC-3 (ATM service). ge Gigabit Ethernet. fe8 Fast Ethernet 8-port. oc3oc12Pos Generic OC3/OC12 POS (multi-personality). oc3oc12Atm Generic OC3/OC12 ATM (multi-personality). coc3oc12 Channelized generic OC3/OC12 (multi-personality). coc3 Channelized OC3. coc12 Channelized OC12. oc12Server OC-12 Rate Server Card. hssi High Speed Serial Interface. geFe Generic GE/FE (multi-personality). ct3P12 Channelized T3 12-port. v35 X.21/V.35 Card. ut3f12 Unchannelized T3 12-port. ue3f12 Unchannelized E3 12-port. coc3F3 OC-3 channelized to T3. coc12F3 OC-12 channelized to T3. cocxF3 12-port T3/E3 or OC3/OC12 (multi-personality).
TEXTUAL-CONVENTION
	INTEGER	unknown(0), srp(1), ct3(2), oc3(3), ut3Atm(4), ut3Frame(5), ue3Atm(6), ue3Frame(7), ce1(8), ct1(9), dpfe(10), oc12Pos(11), oc12Atm(12), oc3Pos(13), oc3Atm(14), ge(15), fe8(16), oc3oc12Pos(17), oc3oc12Atm(18), coc3oc12(19), coc3(20), coc12(21), oc12Server(22), hssi(23), geFe(24), ct3P12(25), v35(26), ut3f12(27), ue3f12(28), coc12F3(29), coc3F3(30), cocxF3(31)

UsdERXSysTimingSelectorEntry
SEQUENCE
	usdERXSysTimingSelectorIndex	UsdTimingSelector
	usdERXSysTimingSourceType	UsdTimingSourceType
	usdERXSysTimingSourceIfIndex	InterfaceIndexOrZero
	usdERXSysTimingSourceLine	UsdTimingSourceLineType
	usdERXSysTimingStatus	INTEGER

UsdERXSysSlotEntry
SEQUENCE
	usdERXSysSlotIndex	Integer32
	usdERXSysSlotDescr	DisplayString
	usdERXSysSlotCurrentCardType	UsdSysCardType
	usdERXSysSlotRev	Integer32
	usdERXSysSlotAdminStatus	UsdEnable
	usdERXSysSlotOperStatus	INTEGER
	usdERXSysSlotDisableReason	INTEGER
	usdERXSysSlotExpectedCardType	UsdSysCardType
	usdERXSysSlotControl	INTEGER
	usdERXSysSlotCpuUtilPct	Integer32
	usdERXSysSlotMemUtilPct	Integer32
	usdERXSysSlotIoaPresent	TruthValue
	usdERXSysSlotPortCount	Integer32
	usdERXSysSlotLastChange	TimeTicks
	usdERXSysSlotRedundancyLockout	UsdEnable
	usdERXSysSlotRedundancyGroupId	Unsigned32
	usdERXSysSlotSpareServer	TruthValue
	usdERXSysSlotAssociatedSlot	Integer32
	usdERXSysSlotRevertControl	INTEGER
	usdERXSysSlotRedundancyRevertTime	DateAndTime
	usdERXSysSlotBootReleaseFile	DisplayString
	usdERXSysSlotBootBackupReleaseFile	DisplayString
	usdERXSysSlotSerialNumber	DisplayString
	usdERXSysSlotAssemblyPartNumber	DisplayString
	usdERXSysSlotAssemblyRev	DisplayString
	usdERXSysSlotIoaSerialNumber	DisplayString
	usdERXSysSlotIoaAssemblyPartNumber	DisplayString
	usdERXSysSlotIoaAssemblyRev	DisplayString

UsdERXSysPortEntry
SEQUENCE
	usdERXSysPortIndex	Integer32
	usdERXSysPortDescr	DisplayString
	usdERXSysPortType	INTEGER
	usdERXSysPortIfIndex	InterfaceIndexOrZero

UsdERXSysPowerEntry
SEQUENCE
	usdERXSysPowerIndex	Integer32
	usdERXSysPowerDescr	DisplayString
	usdERXSysPowerStatus	INTEGER

UsdERXSysTempEntry
SEQUENCE
	usdERXSysTempIndex	Integer32
	usdERXSysTempDescr	DisplayString
	usdERXSysTempStatus	INTEGER
	usdERXSysTempValue	Integer32

UsdERXSysSubsystemEntry
SEQUENCE
	usdERXSysSubsystemIndex	Integer32
	usdERXSysSubsystemName	DisplayString
	usdERXSysSubsystemControl	INTEGER
	usdERXSysSubsystemBootReleaseFile	DisplayString
	usdERXSysSubsystemBootBackupReleaseFile	DisplayString

Defined Values

usdERXSysMIB		1.3.6.1.4.1.4874.2.2.17
MIB objects for managing ERX Edge Router systems.
MODULE-IDENTITY

usdERXSysTrap		1.3.6.1.4.1.4874.2.2.17.0
OBJECT IDENTIFIER

usdERXSysObjects		1.3.6.1.4.1.4874.2.2.17.1
OBJECT IDENTIFIER

usdERXSysConformance		1.3.6.1.4.1.4874.2.2.17.2
OBJECT IDENTIFIER

usdERXSysGeneral		1.3.6.1.4.1.4874.2.2.17.1.1
OBJECT IDENTIFIER

usdERXSysFabric		1.3.6.1.4.1.4874.2.2.17.1.2
OBJECT IDENTIFIER

usdERXSysNvs		1.3.6.1.4.1.4874.2.2.17.1.3
OBJECT IDENTIFIER

usdERXSysSlot		1.3.6.1.4.1.4874.2.2.17.1.4
OBJECT IDENTIFIER

usdERXSysPort		1.3.6.1.4.1.4874.2.2.17.1.5
OBJECT IDENTIFIER

usdERXSysPower		1.3.6.1.4.1.4874.2.2.17.1.6
OBJECT IDENTIFIER

usdERXSysTemperature		1.3.6.1.4.1.4874.2.2.17.1.7
OBJECT IDENTIFIER

usdERXSysSubsystem		1.3.6.1.4.1.4874.2.2.17.1.8
OBJECT IDENTIFIER

usdERXSysChassisRev		1.3.6.1.4.1.4874.2.2.17.1.1.1
Chassis revision number. If unknown, the value 255 is reported.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..255

usdERXSysSwVersion		1.3.6.1.4.1.4874.2.2.17.1.1.2
Currently executing operational software version.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

usdERXSysSwBuildDate		1.3.6.1.4.1.4874.2.2.17.1.1.3
Build date of currently executing operational software version.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString

usdERXSysRevertControl		1.3.6.1.4.1.4874.2.2.17.1.1.4
Global revert control: off Disable global revert. immediate All slots are to revert immediately (asap). timeOfDay All slots are to revert at time specified by usdRxSysRevertTimeOfDay. This object/value must be set concurrently with usdERXSysRevertTimeOfDay.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(0), immediate(1), timeOfDay(2)

usdERXSysRevertTimeOfDay		1.3.6.1.4.1.4874.2.2.17.1.1.5
The number of seconds past midnight on any given day at which time reverts are allowed to occur. This object must be set concurrently with usdERXSysRevertControl.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..86399

usdERXSysBootConfigControl		1.3.6.1.4.1.4874.2.2.17.1.1.6
System boot configuration control: file Revert to configuration settings specified by usdERXSysBootConfigFile. The usdERXSysBootConfigControl and usdERXSysBootConfigFile must be specified together in the same set request PDU. fileOnce Revert to configuration settings specified by usdERXSysBootConfigFile. Do not continue to use file after using it once. The usdERXSysBootConfigControl and usdERXSysBootConfigFile must be specified together in the same set request PDU. factoryDefaults Revert to factory default settings. runningConfiguration Revert to current settings.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	file(0), fileOnce(1), factoryDefaults(2), runningConfiguration(3)

usdERXSysBootBackupConfigControl		1.3.6.1.4.1.4874.2.2.17.1.1.7
System boot backup configuration control: file Revert to backup configuration settings specified by usdERXSysBootBackupConfigFile. The usdERXSysBootBackupConfigControl and usdERXSysBootBackupConfigFile must be specified together in the same set request PDU. factoryDefaults Revert to factory default settings. none Specify no backup.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	file(0), factoryDefaults(1), none(2)

usdERXSysBootForceBackupControl		1.3.6.1.4.1.4874.2.2.17.1.1.8
System boot force backup control: off Do not force revert to backup settings. on Do force revert to backup settings.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(0), on(1)

usdERXSysBootAutoRevertControl		1.3.6.1.4.1.4874.2.2.17.1.1.9
System boot auto revert control: default Use default auto-revert tolerances. never Never auto-revert to backup. set Set auto-revert settings at specified tolerances.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	default(0), never(1), set(2)

usdERXSysBootAutoRevertCountTolerance		1.3.6.1.4.1.4874.2.2.17.1.1.10
The auto-revert reboot count tolerance. This object cannot be set to zero, but may contain a zero value when the control is set to never(1).
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..4294967294

usdERXSysBootAutoRevertTimeTolerance		1.3.6.1.4.1.4874.2.2.17.1.1.11
The auto-revert reboot time tolerance. This object cannot be set to zero, but will contain a zero value when the control is set to never(1).
Status: current	Access: read-write
OBJECT-TYPE
	Unsigned32	0..4294967294

usdERXSysBootReleaseFile		1.3.6.1.4.1.4874.2.2.17.1.1.12
The local boot release file name, with extension .rel.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..128)

usdERXSysBootConfigFile		1.3.6.1.4.1.4874.2.2.17.1.1.13
The local boot configuration file name, with extension .cnf. The usdERXSysBootConfigControl and usdERXSysBootConfigFile must be specified together in the same set request PDU.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..128)

usdERXSysBootBackupReleaseFile		1.3.6.1.4.1.4874.2.2.17.1.1.14
The local backup boot release file name, with extension .rel.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..128)

usdERXSysBootBackupConfigFile		1.3.6.1.4.1.4874.2.2.17.1.1.15
The local backup boot configuration file name, with extension .cnf. The usdERXSysBootBackupConfigControl and usdERXSysBootBackupConfigFile must be specified together in the same set request PDU.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..128)

usdERXSysAdminTimingSource		1.3.6.1.4.1.4874.2.2.17.1.1.16
The administrative timing source for the ERX system. The ERX periodically monitors the status of three timing sources, primary, secondary and tertiary. If the systems current timing source fails, the system will automatically downgrade to the next timing source. If the system is configured to automatically upgrade (usdERXSysTimingDisableAutoUpgrade is set to false(2)) the system will switch back to the higher timing source when it becomes available. A timing source failure can be detected by comparing the operational and admin timing sources. If they are not equal, the system has swapped timing sources because the administratively set value is in the error state.
Status: current	Access: read-write
OBJECT-TYPE
	UsdTimingSelector

usdERXSysOperTimingSource		1.3.6.1.4.1.4874.2.2.17.1.1.17
The operations timing source for the ERX system. The ERX periodically monitors the status of three timing sources, primary, secondary and tertiary. If the systems current timing source fails, the system will automatically downgrade to the next timing source. If the system is configured to automatically upgrade (usdERXSysTimingDisableAutoUpgrade is set to false(2)) the system will switch back to the higher timing source when it becomes available.
Status: current	Access: read-only
OBJECT-TYPE
	UsdTimingSelector

usdERXSysTimingDisableAutoUpgrade		1.3.6.1.4.1.4874.2.2.17.1.1.18
This object controls the automatic timing selector upgrade. Setting this object to true(1) will prevent automatic upgrade to the next highest timing selector. Setting this object to false(2) will enable the automatic upgrade of timing selectors.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

usdERXSysTimingSelectorTable		1.3.6.1.4.1.4874.2.2.17.1.1.19
Table of system timing selectors.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		UsdERXSysTimingSelectorEntry

usdERXSysTimingSelectorEntry		1.3.6.1.4.1.4874.2.2.17.1.1.19.1
A table entry describing a system timing selector.
Status: current	Access: not-accessible
OBJECT-TYPE
	UsdERXSysTimingSelectorEntry

usdERXSysTimingSelectorIndex		1.3.6.1.4.1.4874.2.2.17.1.1.19.1.1
The system timing selector index associated with this entry.
Status: current	Access: not-accessible
OBJECT-TYPE
	UsdTimingSelector

usdERXSysTimingSourceType		1.3.6.1.4.1.4874.2.2.17.1.1.19.1.2
The system timing source type for this entry. This object must be present when setting either the usdERXSysTimingSourceIfIndex or usdERXSysTimingSourceLine objects. Also, if the value of this object is set to timingInternal(2), no other objects should be simultanously set, otherwise the agent will return an error.
Status: current	Access: read-write
OBJECT-TYPE
	UsdTimingSourceType

usdERXSysTimingSourceIfIndex		1.3.6.1.4.1.4874.2.2.17.1.1.19.1.3
The ifIndex of the interface selected as the system timing source. The usdERXSysTimingSourceType object must be set to timingInterfaceIfIndex(1) otherwise setting this object will fail.
Status: current	Access: read-write
OBJECT-TYPE
	InterfaceIndexOrZero

usdERXSysTimingSourceLine		1.3.6.1.4.1.4874.2.2.17.1.1.19.1.4
The line type timing source for this entry. The usdRxSysTimingSourceType object must be set to timingLine(3) for the agent to accept a set to this object.
Status: current	Access: read-write
OBJECT-TYPE
	UsdTimingSourceLineType

usdERXSysTimingStatus		1.3.6.1.4.1.4874.2.2.17.1.1.19.1.5
The status associated with this system timing selector.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	timingStatusOk(1), timingStatusError(2), timingStatusUnknown(3)

usdERXSysMemUtilPct		1.3.6.1.4.1.4874.2.2.17.1.1.20
Percentage of system memory utilization. A value of -1 indicates the utilization is unknown.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-1..100

usdERXSysMemCapacity		1.3.6.1.4.1.4874.2.2.17.1.1.21
The total memory capacity of the system.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

usdERXSysHighMemUtilThreshold		1.3.6.1.4.1.4874.2.2.17.1.1.22
The value of system memory utilization, where if reached for the first time will generate a high memory utilization event to the management entity on this system. The value of this object must be greated than the value of usdERXSysAbatedMemUtilThreshold.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	1..100

usdERXSysAbatedMemUtilThreshold		1.3.6.1.4.1.4874.2.2.17.1.1.23
The value of system memory utilization that is used to determine when to generate an abated memory utilization event notification to the management entity on this system. The value of this object must be less than the value of usdERXSysHighMemUtilThreshold. The abated memory utilization trap is sent once if the high memory threshold was reached, and memory utilization falls to the value of this object.
Status: current	Access: read-write
OBJECT-TYPE
	Integer32	0..99

usdERXSysMemUtilTrapEnable		1.3.6.1.4.1.4874.2.2.17.1.1.24
Controls the sending of system memory utilization events. Setting the value of this object to true(1) will cause system memory utilization event notification, if they occur, to be sent to the management entity on this system. Setting the value of this object to false(2) will disable event notifications.
Status: current	Access: read-write
OBJECT-TYPE
	TruthValue

usdERXSysFabricSpeed		1.3.6.1.4.1.4874.2.2.17.1.2.1
Speed of switching fabric, in gigabits per second.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

usdERXSysFabricRev		1.3.6.1.4.1.4874.2.2.17.1.2.2
Fabric revision number. If unknown, the value 255 is reported.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..255

usdERXSysNvsStatus		1.3.6.1.4.1.4874.2.2.17.1.3.1
Status of non-volatile storage (NVS): notPresent NVS is not installed. writeProtected NVS is write-protected. volumeError Status poll of NVS failed. nearCapacity Utilization exceeds 85% of NVS capacity. ok NVS is operational, none of the preceding conditions apply. nearConfigCapacity Utilization exceeds the ability to save the running configuration.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	notPresent(0), writeProtected(1), volumeError(2), nearCapacity(3), ok(4), nearConfigCapacity(5)

usdERXSysNvsCapacity		1.3.6.1.4.1.4874.2.2.17.1.3.2
Capacity of NVS storage in megabytes.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

usdERXSysNvsUtilPct		1.3.6.1.4.1.4874.2.2.17.1.3.3
Percentage of NVS storage used. A value of -1 indicates NVS utilization is unknown.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-1..100

usdERXSysSlotCount		1.3.6.1.4.1.4874.2.2.17.1.4.1
The number of slots in the system.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

usdERXSysSlotTable		1.3.6.1.4.1.4874.2.2.17.1.4.2
Table of system slots.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		UsdERXSysSlotEntry

usdERXSysSlotEntry		1.3.6.1.4.1.4874.2.2.17.1.4.2.1
A table entry describing contents of a system slot.
Status: current	Access: not-accessible
OBJECT-TYPE
	UsdERXSysSlotEntry

usdERXSysSlotIndex		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.1
Slot number. NOTE: Slot numbers are zero-based.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..255

usdERXSysSlotDescr		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.2
Textual description of the card.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..63)

usdERXSysSlotCurrentCardType		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.3
Type of card actually in the slot. This could be different from the type reported in usdERXSysSlotExpectedCardType, in which case it may be necessary to set usdERXSysSlotControl to 'flush' before this card can be made operational.
Status: current	Access: read-only
OBJECT-TYPE
	UsdSysCardType

usdERXSysSlotRev		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.4
Revision number of the card. If unknown, the value 255 is reported.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..255

usdERXSysSlotAdminStatus		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.5
Exerts administrative control to enable/disable the slot.
Status: current	Access: read-write
OBJECT-TYPE
	UsdEnable

usdERXSysSlotOperStatus		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.6
Status of the card.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), empty(1), disabled(2), failed(3), booting(4), initializing(5), online(6), standby(7), inactive(8)

usdERXSysSlotDisableReason		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.7
Indicates the condition causing the slot to be disabled: none Value when card is not disabled. unknown Unknown reason for disablement. assessing The slot content is being assessed (transient initialization state). admin The slot is administratively disabled. cardMismatch The current card type conflicts with configuration associated with a different card type that previously occupied the slot. fabricLimit Card resource requirements exceed available fabric capacity. imageError Software image for card is missing or invalid.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	none(0), unknown(1), assessing(2), admin(3), cardMismatch(4), fabricLimit(5), imageError(6)

usdERXSysSlotExpectedCardType		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.8
Type of card associated with this slot through prior presence. After the card is removed, this association persists (and inhibits operation of a different card type in this slot, if one is inserted) until usdERXSysSlotControl is set to 'flush'.
Status: current	Access: read-only
OBJECT-TYPE
	UsdSysCardType

usdERXSysSlotControl		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.9
Administrative control of this slot: noOperation Setting this value has no effect. flush Flushes configuration associated with a card type that previously occupied this slot. Used to explicitly confirm that the slot is now empty, or contains a different card type. Card must be disabled when this value is asserted. See description for usdERXSysSlotDisableReason. reset Resets the slot. forceFailover Forces the slot to failover to backup. noBoot Deconfigure primary release file for the slot. noBootBackup Deconfigure backup release file for the slot.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noOperation(0), flush(1), reset(2), forceFailover(3), noBoot(4), noBootBackup(5)

usdERXSysSlotCpuUtilPct		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.10
Percentage of CPU utilization. A value of -1 indicates the utilization is unknown.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-1..100

usdERXSysSlotMemUtilPct		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.11
Percentage of memory utilization. A value of -1 indicates the utilization is unknown.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	-1..100

usdERXSysSlotIoaPresent		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.12
Indicates whether the card's corresponding I/O adapter is present.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

usdERXSysSlotPortCount		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.13
Number of physical ports for the EXPECTED card type for this slot. NOTE: In event of a card mismatch in this slot, the port count for the CURRENT card in this slot is not recognized/reported until the configuration for the EXPECTED card is explicitly flushed via usdERXSysSlotControl.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

usdERXSysSlotLastChange		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.14
The value of sysUpTime when the value of usdERXSysSlotOperStatus last changed.
Status: current	Access: read-only
OBJECT-TYPE
	TimeTicks

usdERXSysSlotRedundancyLockout		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.15
Exerts administrative control to enable/disable Redundancy protection for the slot.
Status: current	Access: read-write
OBJECT-TYPE
	UsdEnable

usdERXSysSlotRedundancyGroupId		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.16
Identifies the Redundancy group as derived from hardware settings.
Status: current	Access: read-only
OBJECT-TYPE
	Unsigned32

usdERXSysSlotSpareServer		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.17
True only if the line card in slot is a spare redundant server.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

usdERXSysSlotAssociatedSlot		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.18
If the module is a primary card and the spare is acting on its behalf, then the value of this object is the slot number of the associated spare. If the module is a primary card and is active (not spared), then the value of this object is the cards actual slot number. If the module is a spare card and it is active, then the value of this object is the slot number of the primary card that is being spared for. If the module is a spare and it is inactive, then the value of this object is the its own slot number. If module is not part of a redundancy group, or the slot is empty, the value of this object is 255.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

usdERXSysSlotRevertControl		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.19
Per-slot revert control: off Disable slot revert. immediate Slot is to revert immediately (asap). timeAndDate Slot is to revert at time specified by usdRxSysSlotRedundancyRevertTime.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	off(0), immediate(1), timeAndDate(2)

usdERXSysSlotRedundancyRevertTime		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.20
The date and time associated with the timeAndDate (delayed) revert operation.
Status: current	Access: read-write
OBJECT-TYPE
	DateAndTime

usdERXSysSlotBootReleaseFile		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.21
The local boot release file name for this slot, with extension .rel.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..128)

usdERXSysSlotBootBackupReleaseFile		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.22
The local backup boot release file name for this slot, with extension .rel.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..128)

usdERXSysSlotSerialNumber		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.23
The serial number of the card in this slot.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..10)

usdERXSysSlotAssemblyPartNumber		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.24
The part number of the card in this slot.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..10)

usdERXSysSlotAssemblyRev		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.25
The revision number of the card assembly in this slot.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..3)

usdERXSysSlotIoaSerialNumber		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.26
The serial number of the I/O adaptor on the card in this slot.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..10)

usdERXSysSlotIoaAssemblyPartNumber		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.27
The part number of the I/O adaptor on the card in this slot.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..10)

usdERXSysSlotIoaAssemblyRev		1.3.6.1.4.1.4874.2.2.17.1.4.2.1.28
The revision number of the I/O adaptor assembly on the card in this slot.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..3)

usdERXSysPortTable		1.3.6.1.4.1.4874.2.2.17.1.5.1
Table of system physical ports. The information in this table reflects the ports for the EXPECTED card type in each slot; in event of a card mismatch, this table permits navigation of the existing configuration of the expected card type.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		UsdERXSysPortEntry

usdERXSysPortEntry		1.3.6.1.4.1.4874.2.2.17.1.5.1.1
A table entry describing a physical port of the system.
Status: current	Access: not-accessible
OBJECT-TYPE
	UsdERXSysPortEntry

usdERXSysPortIndex		1.3.6.1.4.1.4874.2.2.17.1.5.1.1.1
Port number of this physical port, relative to the slot in which it resides. Each physical port is uniquely distinguished by its slot/port pair. NOTE: Port numbers are zero-based.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..255

usdERXSysPortDescr		1.3.6.1.4.1.4874.2.2.17.1.5.1.1.2
Textual description of this port.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..63)

usdERXSysPortType		1.3.6.1.4.1.4874.2.2.17.1.5.1.1.3
Type of the physical port: unknown Unknown port type. eth Ethernet. ct3 Channelized T3. oc3c OC-3c (SONET/SDH). ut3Atm Unchannelized T3 (ATM service). ut3Frame Unchannelized T3 (Frame service). ue3Atm Unchannelized E3 (ATM service). ue3Frame Unchannelized E3 (Frame service). ce1 Channelized E1. ct1 Channelized T1. oc12Pos OC-12 (POS/SDH). oc12Atm OC-12 (ATM service). oc3Pos OC-3 (POS/SDH). oc3Atm OC-3 (ATM service). coc3 Channelized OC-3. coc12 Channelized OC-12. oc12Server OC-12 (Server card). hssi High Speed Serial Interface. v35 X.21/V.35.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), eth(1), ct3(2), oc3c(3), ut3Atm(4), ut3Frame(5), ue3Atm(6), ue3Frame(7), ce1(8), ct1(9), oc12cPos(10), oc12cAtm(11), oc3cPos(12), oc3cAtm(13), coc3(14), coc12(15), oc12Server(16), hssi(17), v35(18)

usdERXSysPortIfIndex		1.3.6.1.4.1.4874.2.2.17.1.5.1.1.4
The ifIndex of the Interfaces MIB ifTable entry corresponding to this physical port; if zero, the ifIndex is unknown or does not exist.
Status: current	Access: read-only
OBJECT-TYPE
	InterfaceIndexOrZero

usdERXSysPowerTable		1.3.6.1.4.1.4874.2.2.17.1.6.1
Table of system power elements.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		UsdERXSysPowerEntry

usdERXSysPowerEntry		1.3.6.1.4.1.4874.2.2.17.1.6.1.1
A table entry describing status of a system power element.
Status: current	Access: not-accessible
OBJECT-TYPE
	UsdERXSysPowerEntry

usdERXSysPowerIndex		1.3.6.1.4.1.4874.2.2.17.1.6.1.1.1
Arbitrary integer index to distinguish entries in this table.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..255

usdERXSysPowerDescr		1.3.6.1.4.1.4874.2.2.17.1.6.1.1.2
Textual description of this power element.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..63)

usdERXSysPowerStatus		1.3.6.1.4.1.4874.2.2.17.1.6.1.1.3
The status of the power element: inactive No power available from this element. active Power available from this element.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	inactive(0), active(1)

usdERXSysTempFanStatus		1.3.6.1.4.1.4874.2.2.17.1.7.1
Status of fan subsystem. ok All components operational warning The fan subsystem has a non-critical failure. failed The fan subsystem has a critical failure, or has been removed, and is now non-operational.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	failed(0), ok(1), warning(2)

usdERXSysTempTable		1.3.6.1.4.1.4874.2.2.17.1.7.2
Table of system temperature sensors. Sensors are distributed across the chassis, at least one sensor per populated slot.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		UsdERXSysTempEntry

usdERXSysTempEntry		1.3.6.1.4.1.4874.2.2.17.1.7.2.1
A table entry describing status of a temperature sensor.
Status: current	Access: not-accessible
OBJECT-TYPE
	UsdERXSysTempEntry

usdERXSysTempIndex		1.3.6.1.4.1.4874.2.2.17.1.7.2.1.1
Arbitrary integer index to distinguish sensors associated with the same chassis slot.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..255

usdERXSysTempDescr		1.3.6.1.4.1.4874.2.2.17.1.7.2.1.2
Textual description of this sensor.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..63)

usdERXSysTempStatus		1.3.6.1.4.1.4874.2.2.17.1.7.2.1.3
The status of a temperature sensor: unknown unknown failed failed tooLow below nominal range nominal within nominal range tooHigh above nominal range tooLowWarning near lower limit tooHighWarning near upper limit
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	unknown(0), failed(1), tooLow(2), nominal(3), tooHigh(4), tooLowWarning(5), tooHighWarning(6)

usdERXSysTempValue		1.3.6.1.4.1.4874.2.2.17.1.7.2.1.4
The temperature measured by this sensor in degrees Celsius. This measurement is valid only if the value of the corresponding usdERXSysTempStatus is nominal.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32

usdERXSysTempProtectionStatus		1.3.6.1.4.1.4874.2.2.17.1.7.3
Thermal protection status: monitoring monitoring inHoldOff hold off time has begun activatedHoldOffExpired hold off time has expired, the system is in thermal protection mode activatedTempTooHigh temperature too high, the system is in thermal protection mode
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	monitoring(1), inHoldOff(2), activatedHoldOffExpired(3), activatedTempTooHigh(4)

usdERXSysTempProtectionHoldOffTime		1.3.6.1.4.1.4874.2.2.17.1.7.4
The time, in seconds, before the system enters thermal protection mode after a critical fan subsystem failure is detected.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..1200

usdERXSysTempProtectionHoldOffTimeRemaining		1.3.6.1.4.1.4874.2.2.17.1.7.5
The time remaining, in seconds, before the system enters thermal protection mode while the thermal protection status is set to inHoldOff. The value decrements every second until it reaches zero, and the status changes to activatedHoldOffExpired. When the thermal protection status is not inHoldOff or activatedHoldOffExpired, the value is set to the hold off time.
Status: current	Access: read-only
OBJECT-TYPE
	Integer32	0..1200

usdERXSysSubsystemTable		1.3.6.1.4.1.4874.2.2.17.1.8.1
Table of subsystems.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		UsdERXSysSubsystemEntry

usdERXSysSubsystemEntry		1.3.6.1.4.1.4874.2.2.17.1.8.1.1
A table entry containing information pertaining to a subsystem.
Status: current	Access: not-accessible
OBJECT-TYPE
	UsdERXSysSubsystemEntry

usdERXSysSubsystemIndex		1.3.6.1.4.1.4874.2.2.17.1.8.1.1.1
Subsystem number.
Status: current	Access: not-accessible
OBJECT-TYPE
	Integer32	0..255

usdERXSysSubsystemName		1.3.6.1.4.1.4874.2.2.17.1.8.1.1.2
The name of the subsystem.
Status: current	Access: read-only
OBJECT-TYPE
	DisplayString	Size(0..128)

usdERXSysSubsystemControl		1.3.6.1.4.1.4874.2.2.17.1.8.1.1.3
Administrative control of this subsystem: noOperation Setting this value has no effect. noBoot Deconfigure primary release file for the subsystem. noBootBackup Deconfigure backup release file for the subsystem.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	noOperation(0), noBoot(1), noBootBackup(2)

usdERXSysSubsystemBootReleaseFile		1.3.6.1.4.1.4874.2.2.17.1.8.1.1.4
The local boot release file name for this subsystem, with extension .rel.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..128)

usdERXSysSubsystemBootBackupReleaseFile		1.3.6.1.4.1.4874.2.2.17.1.8.1.1.5
The local backup boot release file name for this subsystem, with extension .rel.
Status: current	Access: read-write
OBJECT-TYPE
	DisplayString	Size(0..128)

usdERXSysSlotOperStatusChange		1.3.6.1.4.1.4874.2.2.17.0.1
Reports a status change for a slot. This trap is generated on a transition into a stable state (online or disabled) or on a transition out of online.
Status: current	Access: read-write
NOTIFICATION-TYPE

usdERXSysPowerStatusChange		1.3.6.1.4.1.4874.2.2.17.0.2
Reports a change in the status of a power element.
Status: current	Access: read-write
NOTIFICATION-TYPE

usdERXSysTempFanStatusChange		1.3.6.1.4.1.4874.2.2.17.0.3
Reports a transition between the three states of the fan subsystem. When the fan subsystem transitions to the failed state the thermal protection hold off time begins.
Status: current	Access: read-write
NOTIFICATION-TYPE

usdERXSysTempStatusChange		1.3.6.1.4.1.4874.2.2.17.0.4
Reports a change in the temperature status. When the status transitions to the tooHigh state the system enters thermal protection mode.
Status: current	Access: read-write
NOTIFICATION-TYPE

usdERXSysHighMemUtil		1.3.6.1.4.1.4874.2.2.17.0.5
Report system memory utilization has met the conditions of usdERXSysHighMemUtilThreshold.
Status: current	Access: read-write
NOTIFICATION-TYPE

usdERXSysAbatedMemUtil		1.3.6.1.4.1.4874.2.2.17.0.6
Reports system memory utilization has met the conditions of usdERXSysAbatedMemUtilThreshold.
Status: current	Access: read-write
NOTIFICATION-TYPE

usdERXSysTempProtectionStatusChange		1.3.6.1.4.1.4874.2.2.17.0.7
Notification about changes in the state of Thermal Protection. This notification is sent when the tempProtectionStatus changes. It is also sent when the holdOffTimeRemaining is 50% of the holdOffTime.
Status: current	Access: read-write
NOTIFICATION-TYPE

usdERXSysCompliances		1.3.6.1.4.1.4874.2.2.17.2.1
OBJECT IDENTIFIER

usdERXSysGroups		1.3.6.1.4.1.4874.2.2.17.2.2
OBJECT IDENTIFIER

usdERXSysCompliance		1.3.6.1.4.1.4874.2.2.17.2.1.1
Obsolete compliance statement for entities which implement the ERX System MIB. This compliance statement became obsolete when new slot information objects were added.
Status: obsolete	Access: read-write
MODULE-COMPLIANCE

usdERXSysCompliance1		1.3.6.1.4.1.4874.2.2.17.2.1.2
Obsolete compliance statement for entities which implement the ERX System MIB. This compliance statement became obsolete when the timing group was added.
Status: obsolete	Access: read-write
MODULE-COMPLIANCE

usdERXSysCompliance2		1.3.6.1.4.1.4874.2.2.17.2.1.3
Obsolete compliance statement for entities which implement the ERX System MIB. This compliance statement became obsolete when new memory information objects and notifications were added.
Status: obsolete	Access: read-write
MODULE-COMPLIANCE

usdERXSysCompliance3		1.3.6.1.4.1.4874.2.2.17.2.1.4
Obsolete compliance statement for entities which implement the ERX System MIB. This compliance statement became obsolete when new system temperature information objects and notifications were added.
Status: obsolete	Access: read-write
MODULE-COMPLIANCE

usdERXSysCompliance4		1.3.6.1.4.1.4874.2.2.17.2.1.5
The compliance statement for entities which implement the ERX System MIB.
Status: current	Access: read-write
MODULE-COMPLIANCE

usdERXSysGroup		1.3.6.1.4.1.4874.2.2.17.2.2.1
Obsolete collection of management objects pertaining to system capabilities in a Juniper product. This group became obsolete when new slot information objects were added.
Status: obsolete	Access: read-write
OBJECT-GROUP

usdERXSysNotifyGroup		1.3.6.1.4.1.4874.2.2.17.2.2.2
Obsolete collection of management notifications pertaining to system operations in a Juniper product. This group became obsolete when new memory threshold notificaitons were added.
Status: obsolete	Access: read-write
NOTIFICATION-GROUP

usdERXSysGeneralGroup		1.3.6.1.4.1.4874.2.2.17.2.2.3
Obsolete collection of management objects pertaining to general system capabilities in a Juniper product. This group became obsolete when new memory management objects were added.
Status: obsolete	Access: read-write
OBJECT-GROUP

usdERXSysFabricGroup		1.3.6.1.4.1.4874.2.2.17.2.2.4
A collection of management objects pertaining to system fabric capabilities in a Juniper product.
Status: current	Access: read-write
OBJECT-GROUP

usdERXSysNvsGroup		1.3.6.1.4.1.4874.2.2.17.2.2.5
A collection of management objects pertaining to non-volitile storage subsystem capabilities in a Juniper product.
Status: current	Access: read-write
OBJECT-GROUP

usdERXSysSlotGroup		1.3.6.1.4.1.4874.2.2.17.2.2.6
A collection of management objects pertaining to slot-specific system capabilities in a Juniper product.
Status: current	Access: read-write
OBJECT-GROUP

usdERXSysPortGroup		1.3.6.1.4.1.4874.2.2.17.2.2.7
A collection of management objects pertaining to port-related system capabilities in a Juniper product.
Status: current	Access: read-write
OBJECT-GROUP

usdERXSysPowerGroup		1.3.6.1.4.1.4874.2.2.17.2.2.8
A collection of management objects pertaining to the power subsystem capabilities in a Juniper product.
Status: current	Access: read-write
OBJECT-GROUP

usdERXSysTemperatureGroup		1.3.6.1.4.1.4874.2.2.17.2.2.9
Obsolete collection of management objects pertaining to system temperature monitoring capabilities in a Juniper product. This group became obsolete when temperature shutdown parameters were added.
Status: obsolete	Access: read-write
OBJECT-GROUP

usdERXSysSubsystemGroup		1.3.6.1.4.1.4874.2.2.17.2.2.10
A collection of management objects pertaining to subsystem capabilities in a Juniper product.
Status: current	Access: read-write
OBJECT-GROUP

usdERXSysTimingGroup		1.3.6.1.4.1.4874.2.2.17.2.2.11
A collection of management objects pertaining to system timing capabilities in a Juniper product.
Status: current	Access: read-write
OBJECT-GROUP

usdERXSysGeneralGroup2		1.3.6.1.4.1.4874.2.2.17.2.2.12
A collection of management objects pertaining to general system capabilities in a Juniper product.
Status: current	Access: read-write
OBJECT-GROUP

usdERXSysNotifyGroup2		1.3.6.1.4.1.4874.2.2.17.2.2.13
Obsolete collection of management notifications pertaining to system operations in a Juniper product. This group became obsolete when the tempProtectionStatusChange notification was added.
Status: obsolete	Access: read-write
NOTIFICATION-GROUP

usdERXSysTemperatureGroup2		1.3.6.1.4.1.4874.2.2.17.2.2.14
A collection of management objects pertaining to system temperature monitoring capabilities in a Juniper product.
Status: current	Access: read-write
OBJECT-GROUP

usdERXSysNotifyGroup3		1.3.6.1.4.1.4874.2.2.17.2.2.15
A collection of management notifications pertaining to system operations in a Juniper product.
Status: current	Access: read-write
NOTIFICATION-GROUP