Unisphere-Data-DS3-MIB

File: Unisphere-Data-DS3-MIB.mib (25127 bytes)

Imported modules

SNMPv2-SMI SNMPv2-CONF IF-MIB
SNMPv2-TC Unisphere-Data-TC Unisphere-Data-MIBs
PerfHist-TC-MIB RFC1407-MIB

Imported symbols

MODULE-IDENTITY OBJECT-TYPE Integer32
MODULE-COMPLIANCE OBJECT-GROUP ifIndex
InterfaceIndexOrZero TruthValue RowStatus
DisplayString UsdNextIfIndex usDataMibs
PerfCurrentCount PerfIntervalCount PerfTotalCount
dsx3FarEndCurrentEntry dsx3FarEndIntervalEntry dsx3FarEndTotalEntry

Defined Types

UsdDsx3ConfigEntry  
SEQUENCE    
  usdDsx3LineLength Integer32
  usdDsx3LineType INTEGER
  usdDsx3CellScramblerConfig INTEGER
  usdDsx3Channelization TruthValue
  usdDsx3InterfaceType INTEGER
  usdDsx3Application INTEGER
  usdDsx3Ds3Channel INTEGER
  usdDsx3LowerIfIndex InterfaceIndexOrZero
  usdDsx3RowStatus RowStatus
  usdDsx3Ds3DsuMode INTEGER
  usdDsx3Ds3BandwidthLimit INTEGER
  usdDsx3Ds3DsuScrambleMode INTEGER
  usdDsx3MdlCarrier INTEGER
  usdDsx3MdlTransmit INTEGER
  usdDsx3MdlEic DisplayString
  usdDsx3MdlLic DisplayString
  usdDsx3MdlFic DisplayString
  usdDsx3MdlUnit DisplayString
  usdDsx3MdlPfi DisplayString
  usdDsx3MdlPort DisplayString
  usdDsx3MdlGenerator DisplayString

UsdDsx3FarEndCurrentEntry  
SEQUENCE    
  usdDsx3FarEndCurrentInvalidSeconds PerfCurrentCount

UsdDsx3FarEndIntervalEntry  
SEQUENCE    
  usdDsx3FarEndIntervalInvalidSeconds PerfIntervalCount

UsdDsx3FarEndTotalEntry  
SEQUENCE    
  usdDsx3FarEndTotalInvalidSeconds PerfTotalCount

Defined Values

usdDs3MIB 1.3.6.1.4.1.4874.2.2.4
The DS3 MIB for the Unisphere Networks Inc. enterprise.
MODULE-IDENTITY    

usdDs3Objects 1.3.6.1.4.1.4874.2.2.4.1
OBJECT IDENTIFIER    

usdDsx3ConfigTable 1.3.6.1.4.1.4874.2.2.4.1.1
This table contains entries for DS3/E3 interfaces present in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdDsx3ConfigEntry

usdDsx3ConfigEntry 1.3.6.1.4.1.4874.2.2.4.1.1.1
Each entry describes the characteristics of an DS3/E3 interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdDsx3ConfigEntry  

usdDsx3LineLength 1.3.6.1.4.1.4874.2.2.4.1.1.1.1
The length of the DS3/E3 line in meters. This objects provides information for line build out circuitry. This object is only useful if the interface has configurable line build out circuitry.
Status: current Access: read-create
OBJECT-TYPE    
  Integer32 0..64000  

usdDsx3LineType 1.3.6.1.4.1.4874.2.2.4.1.1.1.2
This variable indicates the variety of DS3 C-bit or E3 application implementing this interface. The type of interface affects the interpretation of the usage and error statistics. The rate of DS3 is 44.736 Mbps and E3 is 34.368 Mbps. The dsx3ClearChannel value means that the C-bits are not used except for sending/receiving AIS. Note that this object represents the actual line type when the corresponding value of dsx3LineType is dsx3other(1). The values, in sequence, describe: TITLE: SPECIFICATION: dsx3M23 ANSI T1.107-1988 dsx3SYNTRAN ANSI T1.107-1988 dsx3CbitParity ANSI T1.107a-1989 dsx3ClearChannel ANSI T1.102-1987 e3G832 ITU-T G.832 e3Framed ITU-T G.751 e3Plcp ETSI T/NA(91)18. dsx3M23Plcp ATM Forum af-phy-0054.000 dsx3CbitParityPlcp ATM Forum af-phy-0054.000
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER usdDsx3other(1), usdDsx3M23(2), usdDsx3SYNTRAN(3), usdDsx3CbitParity(4), usdDsx3ClearChannel(5), usdE3G832(6), usdE3Framed(7), usdE3Plcp(8), usdDsx3M23Plcp(18), usdDsx3CbitParityPlcp(20)  

usdDsx3CellScramblerConfig 1.3.6.1.4.1.4874.2.2.4.1.1.1.3
This variable indicates the state of the ATM cell scrambler for interfaces which support ATM over DS3 or E3. For interfaces which do not support ATM, this object returns the value notSupported(3).
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER scramblerOn(1), scramblerOff(2), notSupported(3)  

usdDsx3Channelization 1.3.6.1.4.1.4874.2.2.4.1.1.1.4
The channelization setting for this DS3 interface; true(1) indicates channelization, false(2) indicates no channelization.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

usdDsx3InterfaceType 1.3.6.1.4.1.4874.2.2.4.1.1.1.5
The DS3 interface type setting.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ds3T3(0), ds3E3(1)  

usdDsx3Application 1.3.6.1.4.1.4874.2.2.4.1.1.1.6
The interface application setting.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ds3FrameOverDs3(0), ds3AtmOverDs3(1)  

usdDsx3Ds3Channel 1.3.6.1.4.1.4874.2.2.4.1.1.1.7
The DS3 channel setting. The range of channel settings depends on the line rate of the underlying interface.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 1..28  

usdDsx3LowerIfIndex 1.3.6.1.4.1.4874.2.2.4.1.1.1.8
The ifIndex of the interface over which this DS3 interface is to be layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation.
Status: current Access: read-create
OBJECT-TYPE    
  InterfaceIndexOrZero  

usdDsx3RowStatus 1.3.6.1.4.1.4874.2.2.4.1.1.1.9
Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support setting the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: usdDsx3RowStatus usdDsx3LowerIfIndex In addition, when creating an entry the following conditions must hold: A value for ifIndex must have been determined previously, by reading usdDsx3NextIfIndex. The interface identified by usdDsx3LowerIfIndex must exist. A corresponding entry in ifTable/ifXTable/usdIfTable is created/destroyed as a result of creating/destroying an entry in this table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

usdDsx3Ds3DsuMode 1.3.6.1.4.1.4874.2.2.4.1.1.1.10
The DSU configuration setting for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ds3DsuModeNone(0), ds3DsuLarsCom(2), ds3DsuDigitalLink(4)  

usdDsx3Ds3BandwidthLimit 1.3.6.1.4.1.4874.2.2.4.1.1.1.11
The DSU bandwidth configuration for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER 0..44210  

usdDsx3Ds3DsuScrambleMode 1.3.6.1.4.1.4874.2.2.4.1.1.1.12
The DSU scramble mode setting for this entry.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER ds3DsuScrambleDisabled(0), ds3DsuScrambleEnable(1)  

usdDsx3MdlCarrier 1.3.6.1.4.1.4874.2.2.4.1.1.1.13
Specifies the interface is used in carrier environment.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER disabled(0), enabled(1)  

usdDsx3MdlTransmit 1.3.6.1.4.1.4874.2.2.4.1.1.1.14
Specifies transmission enabling.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER path(1), idlesignal(2), testsignal(4), none(8)  

usdDsx3MdlEic 1.3.6.1.4.1.4874.2.2.4.1.1.1.15
This is the equipment identification code.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..10)  

usdDsx3MdlLic 1.3.6.1.4.1.4874.2.2.4.1.1.1.16
This is the location identification code.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..11)  

usdDsx3MdlFic 1.3.6.1.4.1.4874.2.2.4.1.1.1.17
This is the frame identification code.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..10)  

usdDsx3MdlUnit 1.3.6.1.4.1.4874.2.2.4.1.1.1.18
This is the unit identification code.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..6)  

usdDsx3MdlPfi 1.3.6.1.4.1.4874.2.2.4.1.1.1.19
This is the facility identification code to send in the MDL path message.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..38)  

usdDsx3MdlPort 1.3.6.1.4.1.4874.2.2.4.1.1.1.20
This is the equipment port number to send in the MDL idle signal message.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..38)  

usdDsx3MdlGenerator 1.3.6.1.4.1.4874.2.2.4.1.1.1.21
This is the generator number to send in the MDL test signal message.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..38)  

usdDs3NextIfIndex 1.3.6.1.4.1.4874.2.2.4.1.2
Coordinate ifIndex value allocation for entries in usdDsx3ConfigTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
Status: current Access: read-only
OBJECT-TYPE    
  UsdNextIfIndex  

usdDsx3FarEndCurrentTable 1.3.6.1.4.1.4874.2.2.4.1.3
This table contains entries for DS3/E3 interfaces present in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdDsx3FarEndCurrentEntry

usdDsx3FarEndCurrentEntry 1.3.6.1.4.1.4874.2.2.4.1.3.1
Each entry describes the characteristics of an DS3/E3 interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdDsx3FarEndCurrentEntry  

usdDsx3FarEndCurrentInvalidSeconds 1.3.6.1.4.1.4874.2.2.4.1.3.1.1
The counter associated with the number of Invalid Seconds encountered by a DS3/E3 interface in the current 15 minute interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfCurrentCount  

usdDsx3FarEndIntervalTable 1.3.6.1.4.1.4874.2.2.4.1.4
This table contains entries for DS3/E3 interfaces present in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdDsx3FarEndIntervalEntry

usdDsx3FarEndIntervalEntry 1.3.6.1.4.1.4874.2.2.4.1.4.1
Each entry describes the characteristics of an DS3/E3 interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdDsx3FarEndIntervalEntry  

usdDsx3FarEndIntervalInvalidSeconds 1.3.6.1.4.1.4874.2.2.4.1.4.1.1
The counter associated with the number of Invalid Seconds encountered by a DS3/E3 interface in one of the previous 96 individual 15 minute intervals.
Status: current Access: read-only
OBJECT-TYPE    
  PerfIntervalCount  

usdDsx3FarEndTotalTable 1.3.6.1.4.1.4874.2.2.4.1.5
This table contains entries for DS3/E3 interfaces present in the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UsdDsx3FarEndTotalEntry

usdDsx3FarEndTotalEntry 1.3.6.1.4.1.4874.2.2.4.1.5.1
Each entry describes the characteristics of an DS3/E3 interface.
Status: current Access: not-accessible
OBJECT-TYPE    
  UsdDsx3FarEndTotalEntry  

usdDsx3FarEndTotalInvalidSeconds 1.3.6.1.4.1.4874.2.2.4.1.5.1.1
The counter associated with the number of Invalid Seconds encountered by a DS3/E3 interface in the previous 24 hour interval.
Status: current Access: read-only
OBJECT-TYPE    
  PerfTotalCount  

usdDs3Conformance 1.3.6.1.4.1.4874.2.2.4.4
OBJECT IDENTIFIER    

usdDs3Compliances 1.3.6.1.4.1.4874.2.2.4.4.1
OBJECT IDENTIFIER    

usdDs3Groups 1.3.6.1.4.1.4874.2.2.4.4.2
OBJECT IDENTIFIER    

usdDs3Compliance 1.3.6.1.4.1.4874.2.2.4.4.1.1
Obsolete compliance statement for entities which implement the Unisphere DS3/E3 MIB. This statement became obsolete when support was added for line type and cell scrambler objects.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

usdDs3Compliance2 1.3.6.1.4.1.4874.2.2.4.4.1.2
Obsolete compliance statement for entities which implement the Unisphere DS3/E3 MIB. This statement became obsolete when support was added for DSU objects.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

usdDs3Compliance3 1.3.6.1.4.1.4874.2.2.4.4.1.3
Obsolete compliance statement for entities which implement the Unisphere DS3/E3 MIB. This statement became obsolete when support was added for dynamic DS3 interface objects.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

usdDs3Compliance4 1.3.6.1.4.1.4874.2.2.4.4.1.4
Obsolete compliance statement for entities which implement the Unisphere DS3/E3 MIB. This statement became obsolete when far end invalid seconds objects and more configuration objects were added.
Status: obsolete Access: read-only
MODULE-COMPLIANCE    

usdDs3Compliance5 1.3.6.1.4.1.4874.2.2.4.4.1.5
The compliance statement for entities which implement the Unisphere DS3/E3 MIB.
Status: current Access: read-only
MODULE-COMPLIANCE    

usdDs3Group 1.3.6.1.4.1.4874.2.2.4.4.2.1
Obsolete collection of objects providing management of DS3/E3 interfaces in a Unisphere product. This group became obsolete when support was added for line type and cell scrambler objects.
Status: obsolete Access: read-only
OBJECT-GROUP    

usdDs3Group2 1.3.6.1.4.1.4874.2.2.4.4.2.2
Obsolete collection of objects providing management of DS3/E3 interfaces in a Unisphere product. This group became obsolete when support was added for DSU configuration objects.
Status: obsolete Access: read-only
OBJECT-GROUP    

usdDs3Group3 1.3.6.1.4.1.4874.2.2.4.4.2.3
Obsolete collection of objects providing management of DS3/E3 interfaces in a Unisphere product. This group became obsolete when support was added for dynamic DS3 interface objects.
Status: obsolete Access: read-only
OBJECT-GROUP    

usdDs3Group4 1.3.6.1.4.1.4874.2.2.4.4.2.4
Obsolete collection of objects providing management of DS3/E3 interfaces in a Unisphere product. This group became obsolete when more configuration objects were added.
Status: obsolete Access: read-only
OBJECT-GROUP    

usdDs3Group5 1.3.6.1.4.1.4874.2.2.4.4.2.5
A collection of objects providing management of DS3/E3 interfaces in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP    

usdDs3FarEndGroup 1.3.6.1.4.1.4874.2.2.4.4.2.6
A collection of objects providing remote statistics information applicable to DS3 interfaces in a Unisphere product.
Status: current Access: read-only
OBJECT-GROUP