UPS-MIB

File: UPS-MIB.mib (66844 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SNMPv2-CONF

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
OBJECT-IDENTITY Counter32 Gauge32
Integer32 mib-2 DisplayString
TimeStamp TimeInterval TestAndIncr
AutonomousType MODULE-COMPLIANCE OBJECT-GROUP

Defined Types

PositiveInteger  
This data type is a non-zero and non-negative value.
TEXTUAL-CONVENTION    
  INTEGER 1..2147483647  

NonNegativeInteger  
This data type is a non-negative value.
TEXTUAL-CONVENTION    
  INTEGER 0..2147483647  

UpsInputEntry  
SEQUENCE    
  upsInputLineIndex PositiveInteger
  upsInputFrequency NonNegativeInteger
  upsInputVoltage NonNegativeInteger
  upsInputCurrent NonNegativeInteger
  upsInputTruePower NonNegativeInteger

UpsOutputEntry  
SEQUENCE    
  upsOutputLineIndex PositiveInteger
  upsOutputVoltage NonNegativeInteger
  upsOutputCurrent NonNegativeInteger
  upsOutputPower NonNegativeInteger
  upsOutputPercentLoad INTEGER

UpsBypassEntry  
SEQUENCE    
  upsBypassLineIndex PositiveInteger
  upsBypassVoltage NonNegativeInteger
  upsBypassCurrent NonNegativeInteger
  upsBypassPower NonNegativeInteger

UpsAlarmEntry  
SEQUENCE    
  upsAlarmId PositiveInteger
  upsAlarmDescr AutonomousType
  upsAlarmTime TimeStamp

Defined Values

upsMIB 1.3.6.1.2.1.33
The MIB module to describe Uninterruptible Power Supplies.
MODULE-IDENTITY    

upsObjects 1.3.6.1.2.1.33.1
OBJECT IDENTIFIER    

upsIdent 1.3.6.1.2.1.33.1.1
OBJECT IDENTIFIER    

upsIdentManufacturer 1.3.6.1.2.1.33.1.1.1
The name of the UPS manufacturer.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..31)  

upsIdentModel 1.3.6.1.2.1.33.1.1.2
The UPS Model designation.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsIdentUPSSoftwareVersion 1.3.6.1.2.1.33.1.1.3
The UPS firmware/software version(s). This variable may or may not have the same value as upsIdentAgentSoftwareVersion in some implementations.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsIdentAgentSoftwareVersion 1.3.6.1.2.1.33.1.1.4
The UPS agent software version. This variable may or may not have the same value as upsIdentUPSSoftwareVersion in some implementations.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsIdentName 1.3.6.1.2.1.33.1.1.5
A string identifying the UPS. This object should be set by the administrator.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsIdentAttachedDevices 1.3.6.1.2.1.33.1.1.6
A string identifying the devices attached to the output(s) of the UPS. This object should be set by the administrator.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..63)  

upsBattery 1.3.6.1.2.1.33.1.2
OBJECT IDENTIFIER    

upsBatteryStatus 1.3.6.1.2.1.33.1.2.1
The indication of the capacity remaining in the UPS system's batteries. A value of batteryNormal indicates that the remaining run-time is greater than upsConfigLowBattTime. A value of batteryLow indicates that the remaining battery run-time is less than or equal to upsConfigLowBattTime. A value of batteryDepleted indicates that the UPS will be unable to sustain the present load when and if the utility power is lost (including the possibility that the utility power is currently absent and the UPS is unable to sustain the output).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(1), batteryNormal(2), batteryLow(3), batteryDepleted(4)  

upsSecondsOnBattery 1.3.6.1.2.1.33.1.2.2
If the unit is on battery power, the elapsed time since the UPS last switched to battery power, or the time since the network management subsystem was last restarted, whichever is less. Zero shall be returned if the unit is not on battery power.
Status: current Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsEstimatedMinutesRemaining 1.3.6.1.2.1.33.1.2.3
An estimate of the time to battery charge depletion under the present load conditions if the utility power is off and remains off, or if it were to be lost and remain off.
Status: current Access: read-only
OBJECT-TYPE    
  PositiveInteger  

upsEstimatedChargeRemaining 1.3.6.1.2.1.33.1.2.4
An estimate of the battery charge remaining expressed as a percent of full charge.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..100  

upsBatteryVoltage 1.3.6.1.2.1.33.1.2.5
The magnitude of the present battery voltage.
Status: current Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsBatteryCurrent 1.3.6.1.2.1.33.1.2.6
The present battery current.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

upsBatteryTemperature 1.3.6.1.2.1.33.1.2.7
The ambient temperature at or near the UPS Battery casing.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

upsInput 1.3.6.1.2.1.33.1.3
OBJECT IDENTIFIER    

upsInputLineBads 1.3.6.1.2.1.33.1.3.1
A count of the number of times the input entered an out-of-tolerance condition as defined by the manufacturer. This count is incremented by one each time the input transitions from zero out-of-tolerance lines to one or more input lines out-of-tolerance.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

upsInputNumLines 1.3.6.1.2.1.33.1.3.2
The number of input lines utilized in this device. This variable indicates the number of rows in the input table.
Status: current Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsInputTable 1.3.6.1.2.1.33.1.3.3
A list of input table entries. The number of entries is given by the value of upsInputNumLines.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UpsInputEntry

upsInputEntry 1.3.6.1.2.1.33.1.3.3.1
An entry containing information applicable to a particular input line.
Status: current Access: not-accessible
OBJECT-TYPE    
  UpsInputEntry  

upsInputLineIndex 1.3.6.1.2.1.33.1.3.3.1.1
The input line identifier.
Status: current Access: not-accessible
OBJECT-TYPE    
  PositiveInteger  

upsInputFrequency 1.3.6.1.2.1.33.1.3.3.1.2
The present input frequency.
Status: current Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsInputVoltage 1.3.6.1.2.1.33.1.3.3.1.3
The magnitude of the present input voltage.
Status: current Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsInputCurrent 1.3.6.1.2.1.33.1.3.3.1.4
The magnitude of the present input current.
Status: current Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsInputTruePower 1.3.6.1.2.1.33.1.3.3.1.5
The magnitude of the present input true power.
Status: current Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutput 1.3.6.1.2.1.33.1.4
OBJECT IDENTIFIER    

upsOutputSource 1.3.6.1.2.1.33.1.4.1
The present source of output power. The enumeration none(2) indicates that there is no source of output power (and therefore no output power), for example, the system has opened the output breaker.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER other(1), none(2), normal(3), bypass(4), battery(5), booster(6), reducer(7)  

upsOutputFrequency 1.3.6.1.2.1.33.1.4.2
The present output frequency.
Status: current Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputNumLines 1.3.6.1.2.1.33.1.4.3
The number of output lines utilized in this device. This variable indicates the number of rows in the output table.
Status: current Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputTable 1.3.6.1.2.1.33.1.4.4
A list of output table entries. The number of entries is given by the value of upsOutputNumLines.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UpsOutputEntry

upsOutputEntry 1.3.6.1.2.1.33.1.4.4.1
An entry containing information applicable to a particular output line.
Status: current Access: not-accessible
OBJECT-TYPE    
  UpsOutputEntry  

upsOutputLineIndex 1.3.6.1.2.1.33.1.4.4.1.1
The output line identifier.
Status: current Access: not-accessible
OBJECT-TYPE    
  PositiveInteger  

upsOutputVoltage 1.3.6.1.2.1.33.1.4.4.1.2
The present output voltage.
Status: current Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputCurrent 1.3.6.1.2.1.33.1.4.4.1.3
The present output current.
Status: current Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputPower 1.3.6.1.2.1.33.1.4.4.1.4
The present output true power.
Status: current Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsOutputPercentLoad 1.3.6.1.2.1.33.1.4.4.1.5
The percentage of the UPS power capacity presently being used on this output line, i.e., the greater of the percent load of true power capacity and the percent load of VA.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..200  

upsBypass 1.3.6.1.2.1.33.1.5
OBJECT IDENTIFIER    

upsBypassFrequency 1.3.6.1.2.1.33.1.5.1
The present bypass frequency.
Status: current Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsBypassNumLines 1.3.6.1.2.1.33.1.5.2
The number of bypass lines utilized in this device. This entry indicates the number of rows in the bypass table.
Status: current Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsBypassTable 1.3.6.1.2.1.33.1.5.3
A list of bypass table entries. The number of entries is given by the value of upsBypassNumLines.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UpsBypassEntry

upsBypassEntry 1.3.6.1.2.1.33.1.5.3.1
An entry containing information applicable to a particular bypass input.
Status: current Access: not-accessible
OBJECT-TYPE    
  UpsBypassEntry  

upsBypassLineIndex 1.3.6.1.2.1.33.1.5.3.1.1
The bypass line identifier.
Status: current Access: not-accessible
OBJECT-TYPE    
  PositiveInteger  

upsBypassVoltage 1.3.6.1.2.1.33.1.5.3.1.2
The present bypass voltage.
Status: current Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsBypassCurrent 1.3.6.1.2.1.33.1.5.3.1.3
The present bypass current.
Status: current Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsBypassPower 1.3.6.1.2.1.33.1.5.3.1.4
The present true power conveyed by the bypass.
Status: current Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsAlarm 1.3.6.1.2.1.33.1.6
OBJECT IDENTIFIER    

upsAlarmsPresent 1.3.6.1.2.1.33.1.6.1
The present number of active alarm conditions.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

upsAlarmTable 1.3.6.1.2.1.33.1.6.2
A list of alarm table entries. The table contains zero, one, or many rows at any moment, depending upon the number of alarm conditions in effect. The table is initially empty at agent startup. The agent creates a row in the table each time a condition is detected and deletes that row when that condition no longer pertains. The agent creates the first row with upsAlarmId equal to 1, and increments the value of upsAlarmId each time a new row is created, wrapping to the first free value greater than or equal to 1 when the maximum value of upsAlarmId would otherwise be exceeded. Consequently, after multiple operations, the table may become sparse, e.g., containing entries for rows 95, 100, 101, and 203 and the entries should not be assumed to be in chronological order because upsAlarmId might have wrapped. Alarms are named by an AutonomousType (OBJECT IDENTIFIER), upsAlarmDescr, to allow a single table to reflect well known alarms plus alarms defined by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. No two rows will have the same value of upsAlarmDescr, since alarms define conditions. In order to meet this requirement, care should be taken in the definition of alarm conditions to insure that a system cannot enter the same condition multiple times simultaneously. The number of rows in the table at any given time is reflected by the value of upsAlarmsPresent.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    UpsAlarmEntry

upsAlarmEntry 1.3.6.1.2.1.33.1.6.2.1
An entry containing information applicable to a particular alarm.
Status: current Access: not-accessible
OBJECT-TYPE    
  UpsAlarmEntry  

upsAlarmId 1.3.6.1.2.1.33.1.6.2.1.1
A unique identifier for an alarm condition. This value must remain constant.
Status: current Access: not-accessible
OBJECT-TYPE    
  PositiveInteger  

upsAlarmDescr 1.3.6.1.2.1.33.1.6.2.1.2
A reference to an alarm description object. The object referenced should not be accessible, but rather be used to provide a unique description of the alarm condition.
Status: current Access: read-only
OBJECT-TYPE    
  AutonomousType  

upsAlarmTime 1.3.6.1.2.1.33.1.6.2.1.3
The value of sysUpTime when the alarm condition was detected. If the alarm condition was detected at the time of agent startup and presumably existed before agent startup, the value of upsAlarmTime shall equal 0.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

upsWellKnownAlarms 1.3.6.1.2.1.33.1.6.3
OBJECT IDENTIFIER    

upsAlarmBatteryBad 1.3.6.1.2.1.33.1.6.3.1
One or more batteries have been determined to require replacement.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmOnBattery 1.3.6.1.2.1.33.1.6.3.2
The UPS is drawing power from the batteries.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmLowBattery 1.3.6.1.2.1.33.1.6.3.3
The remaining battery run-time is less than or equal to upsConfigLowBattTime.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmDepletedBattery 1.3.6.1.2.1.33.1.6.3.4
The UPS will be unable to sustain the present load when and if the utility power is lost.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmTempBad 1.3.6.1.2.1.33.1.6.3.5
A temperature is out of tolerance.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmInputBad 1.3.6.1.2.1.33.1.6.3.6
An input condition is out of tolerance.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmOutputBad 1.3.6.1.2.1.33.1.6.3.7
An output condition (other than OutputOverload) is out of tolerance.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmOutputOverload 1.3.6.1.2.1.33.1.6.3.8
The output load exceeds the UPS output capacity.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmOnBypass 1.3.6.1.2.1.33.1.6.3.9
The Bypass is presently engaged on the UPS.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmBypassBad 1.3.6.1.2.1.33.1.6.3.10
The Bypass is out of tolerance.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmOutputOffAsRequested 1.3.6.1.2.1.33.1.6.3.11
The UPS has shutdown as requested, i.e., the output is off.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmUpsOffAsRequested 1.3.6.1.2.1.33.1.6.3.12
The entire UPS has shutdown as commanded.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmChargerFailed 1.3.6.1.2.1.33.1.6.3.13
An uncorrected problem has been detected within the UPS charger subsystem.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmUpsOutputOff 1.3.6.1.2.1.33.1.6.3.14
The output of the UPS is in the off state.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmUpsSystemOff 1.3.6.1.2.1.33.1.6.3.15
The UPS system is in the off state.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmFanFailure 1.3.6.1.2.1.33.1.6.3.16
The failure of one or more fans in the UPS has been detected.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmFuseFailure 1.3.6.1.2.1.33.1.6.3.17
The failure of one or more fuses has been detected.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmGeneralFault 1.3.6.1.2.1.33.1.6.3.18
A general fault in the UPS has been detected.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmDiagnosticTestFailed 1.3.6.1.2.1.33.1.6.3.19
The result of the last diagnostic test indicates a failure.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmCommunicationsLost 1.3.6.1.2.1.33.1.6.3.20
A problem has been encountered in the communications between the agent and the UPS.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmAwaitingPower 1.3.6.1.2.1.33.1.6.3.21
The UPS output is off and the UPS is awaiting the return of input power.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmShutdownPending 1.3.6.1.2.1.33.1.6.3.22
A upsShutdownAfterDelay countdown is underway.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmShutdownImminent 1.3.6.1.2.1.33.1.6.3.23
The UPS will turn off power to the load in less than 5 seconds; this may be either a timed shutdown or a low battery shutdown.
Status: current Access: read-only
OBJECT-IDENTITY    

upsAlarmTestInProgress 1.3.6.1.2.1.33.1.6.3.24
A test is in progress, as initiated and indicated by the Test Group. Tests initiated via other implementation-specific mechanisms can indicate the presence of the testing in the alarm table, if desired, via a OBJECT-IDENTITY macro in the MIB document specific to that implementation and are outside the scope of this OBJECT-IDENTITY.
Status: current Access: read-only
OBJECT-IDENTITY    

upsTest 1.3.6.1.2.1.33.1.7
OBJECT IDENTIFIER    

upsTestId 1.3.6.1.2.1.33.1.7.1
The test is named by an OBJECT IDENTIFIER which allows a standard mechanism for the initiation of tests, including the well known tests identified in this document as well as those introduced by a particular implementation, i.e., as documented in the private enterprise MIB definition for the device. Setting this variable initiates the named test. Sets to this variable require the presence of upsTestSpinLock in the same SNMP message. The set request will be rejected with an appropriate error message if the requested test cannot be performed, including attempts to start a test when another test is already in progress. The status of the current or last test is maintained in upsTestResultsSummary. Tests in progress may be aborted by setting the upsTestId variable to upsTestAbortTestInProgress. Read operations return the value of the name of the test in progress if a test is in progress or the name of the last test performed if no test is in progress, unless no test has been run, in which case the well known value upsTestNoTestsInitiated is returned.
Status: current Access: read-write
OBJECT-TYPE    
  OBJECT IDENTIFIER  

upsTestSpinLock 1.3.6.1.2.1.33.1.7.2
A spin lock on the test subsystem. The spinlock is used as follows. Before starting a test, a manager-station should make sure that a test is not in progress as follows: try_again: get (upsTestSpinLock) while (upsTestResultsSummary == inProgress) { /* loop while a test is running for another manager */ short delay get (upsTestSpinLock) } lock_value = upsTestSpinLock /* no test in progress, start the test */ set (upsTestSpinLock = lock_value, upsTestId = requested_test) if (error_index == 1) { /* (upsTestSpinLock failed) */ /* if problem is not access control, then some other manager slipped in ahead of us */ goto try_again } if (error_index == 2) { /* (upsTestId) */ /* cannot perform the test */ give up } /* test started ok */ /* wait for test completion by polling upsTestResultsSummary */ get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) while (upsTestResultsSummary == inProgress) { short delay get (upsTestSpinLock, upsTestResultsSummary, upsTestResultsDetail) } /* when test completes, retrieve any additional test results */ /* if upsTestSpinLock == lock_value + 1, then these are our test */ /* results (as opposed to another manager's */ The initial value of upsTestSpinLock at agent initialization shall be 1.
Status: current Access: read-write
OBJECT-TYPE    
  TestAndIncr  

upsTestResultsSummary 1.3.6.1.2.1.33.1.7.3
The results of the current or last UPS diagnostics test performed. The values for donePass(1), doneWarning(2), and doneError(3) indicate that the test completed either successfully, with a warning, or with an error, respectively. The value aborted(4) is returned for tests which are aborted by setting the value of upsTestId to upsTestAbortTestInProgress. Tests which have not yet concluded are indicated by inProgress(5). The value noTestsInitiated(6) indicates that no previous test results are available, such as is the case when no tests have been run since the last reinitialization of the network management subsystem and the system has no provision for non- volatile storage of test results.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER donePass(1), doneWarning(2), doneError(3), aborted(4), inProgress(5), noTestsInitiated(6)  

upsTestResultsDetail 1.3.6.1.2.1.33.1.7.4
Additional information about upsTestResultsSummary. If no additional information available, a zero length string is returned.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..255)  

upsTestStartTime 1.3.6.1.2.1.33.1.7.5
The value of sysUpTime at the time the test in progress was initiated, or, if no test is in progress, the time the previous test was initiated. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestStartTime has the value 0.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

upsTestElapsedTime 1.3.6.1.2.1.33.1.7.6
The amount of time, in TimeTicks, since the test in progress was initiated, or, if no test is in progress, the previous test took to complete. If the value of upsTestResultsSummary is noTestsInitiated(6), upsTestElapsedTime has the value 0.
Status: current Access: read-only
OBJECT-TYPE    
  TimeInterval  

upsWellKnownTests 1.3.6.1.2.1.33.1.7.7
OBJECT IDENTIFIER    

upsTestNoTestsInitiated 1.3.6.1.2.1.33.1.7.7.1
No tests have been initiated and no test is in progress.
Status: current Access: read-only
OBJECT-IDENTITY    

upsTestAbortTestInProgress 1.3.6.1.2.1.33.1.7.7.2
The test in progress is to be aborted / the test in progress was aborted.
Status: current Access: read-only
OBJECT-IDENTITY    

upsTestGeneralSystemsTest 1.3.6.1.2.1.33.1.7.7.3
The manufacturer's standard test of UPS device systems.
Status: current Access: read-only
OBJECT-IDENTITY    

upsTestQuickBatteryTest 1.3.6.1.2.1.33.1.7.7.4
A test that is sufficient to determine if the battery needs replacement.
Status: current Access: read-only
OBJECT-IDENTITY    

upsTestDeepBatteryCalibration 1.3.6.1.2.1.33.1.7.7.5
The system is placed on battery to a discharge level, set by the manufacturer, sufficient to determine battery replacement and battery run-time with a high degree of confidence. WARNING: this test will leave the battery in a low charge state and will require time for recharging to a level sufficient to provide normal battery duration for the protected load.
Status: current Access: read-only
OBJECT-IDENTITY    

upsControl 1.3.6.1.2.1.33.1.8
OBJECT IDENTIFIER    

upsShutdownType 1.3.6.1.2.1.33.1.8.1
This object determines the nature of the action to be taken at the time when the countdown of the upsShutdownAfterDelay and upsRebootWithDuration objects reaches zero. Setting this object to output(1) indicates that shutdown requests should cause only the output of the UPS to turn off. Setting this object to system(2) indicates that shutdown requests will cause the entire UPS system to turn off.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER output(1), system(2)  

upsShutdownAfterDelay 1.3.6.1.2.1.33.1.8.2
Setting this object will shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) after the indicated number of seconds, or less if the UPS batteries become depleted. Setting this object to 0 will cause the shutdown to occur immediately. Setting this object to -1 will abort the countdown. If the system is already in the desired state at the time the countdown reaches 0, then nothing will happen. That is, there is no additional action at that time if upsShutdownType = system and the system is already off. Similarly, there is no additional action at that time if upsShutdownType = output and the output is already off. When read, upsShutdownAfterDelay will return the number of seconds remaining until shutdown, or -1 if no shutdown countdown is in effect. On some systems, if the agent is restarted while a shutdown countdown is in effect, the countdown may be aborted. Sets to this object override any upsShutdownAfterDelay already in effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -1..2147483648  

upsStartupAfterDelay 1.3.6.1.2.1.33.1.8.3
Setting this object will start the output after the indicated number of seconds, including starting the UPS, if necessary. Setting this object to 0 will cause the startup to occur immediately. Setting this object to -1 will abort the countdown. If the output is already on at the time the countdown reaches 0, then nothing will happen. Sets to this object override the effect of any upsStartupAfterDelay countdown or upsRebootWithDuration countdown in progress. When read, upsStartupAfterDelay will return the number of seconds until startup, or -1 if no startup countdown is in effect. If the countdown expires during a utility failure, the startup shall not occur until the utility power is restored. On some systems, if the agent is restarted while a startup countdown is in effect, the countdown is aborted.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -1..2147483648  

upsRebootWithDuration 1.3.6.1.2.1.33.1.8.4
Setting this object will immediately shutdown (i.e., turn off) either the UPS output or the UPS system (as determined by the value of upsShutdownType at the time of shutdown) for a period equal to the indicated number of seconds, after which time the output will be started, including starting the UPS, if necessary. If the number of seconds required to perform the request is greater than the requested duration, then the requested shutdown and startup cycle shall be performed in the minimum time possible, but in no case shall this require more than the requested duration plus 60 seconds. When read, upsRebootWithDuration shall return the number of seconds remaining in the countdown, or -1 if no countdown is in progress. If the startup should occur during a utility failure, the startup shall not occur until the utility power is restored.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER -1..300  

upsAutoRestart 1.3.6.1.2.1.33.1.8.5
Setting this object to 'on' will cause the UPS system to restart after a shutdown if the shutdown occurred during a power loss as a result of either a upsShutdownAfterDelay or an internal battery depleted condition. Setting this object to 'off' will prevent the UPS system from restarting after a shutdown until an operator manually or remotely explicitly restarts it. If the UPS is in a startup or reboot countdown, then the UPS will not restart until that delay has been satisfied.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER on(1), off(2)  

upsConfig 1.3.6.1.2.1.33.1.9
OBJECT IDENTIFIER    

upsConfigInputVoltage 1.3.6.1.2.1.33.1.9.1
The magnitude of the nominal input voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.
Status: current Access: read-write
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigInputFreq 1.3.6.1.2.1.33.1.9.2
The nominal input frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.
Status: current Access: read-write
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigOutputVoltage 1.3.6.1.2.1.33.1.9.3
The magnitude of the nominal output voltage. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.
Status: current Access: read-write
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigOutputFreq 1.3.6.1.2.1.33.1.9.4
The nominal output frequency. On those systems which support read-write access to this object, if there is an attempt to set this variable to a value that is not supported, the request must be rejected and the agent shall respond with an appropriate error message, i.e., badValue for SNMPv1, or inconsistentValue for SNMPv2.
Status: current Access: read-write
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigOutputVA 1.3.6.1.2.1.33.1.9.5
The magnitude of the nominal Volt-Amp rating.
Status: current Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigOutputPower 1.3.6.1.2.1.33.1.9.6
The magnitude of the nominal true power rating.
Status: current Access: read-only
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigLowBattTime 1.3.6.1.2.1.33.1.9.7
The value of upsEstimatedMinutesRemaining at which a lowBattery condition is declared. For agents which support only discrete (discontinuous) values, then the agent shall round up to the next supported value. If the requested value is larger than the largest supported value, then the largest supported value shall be selected.
Status: current Access: read-write
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigAudibleStatus 1.3.6.1.2.1.33.1.9.8
The requested state of the audible alarm. When in the disabled state, the audible alarm should never sound. The enabled state is self-describing. Setting this object to muted(3) when the audible alarm is sounding shall temporarily silence the alarm. It will remain muted until it would normally stop sounding and the value returned for read operations during this period shall equal muted(3). At the end of this period, the value shall revert to enabled(2). Writes of the value muted(3) when the audible alarm is not sounding shall be accepted but otherwise shall have no effect.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2), muted(3)  

upsConfigLowVoltageTransferPoint 1.3.6.1.2.1.33.1.9.9
The minimum input line voltage allowed before the UPS system transfers to battery backup.
Status: current Access: read-write
OBJECT-TYPE    
  NonNegativeInteger  

upsConfigHighVoltageTransferPoint 1.3.6.1.2.1.33.1.9.10
The maximum line voltage allowed before the UPS system transfers to battery backup.
Status: current Access: read-write
OBJECT-TYPE    
  NonNegativeInteger  

upsTraps 1.3.6.1.2.1.33.2
OBJECT IDENTIFIER    

upsTrapOnBattery 1.3.6.1.2.1.33.2.1
The UPS is operating on battery power. This trap is persistent and is resent at one minute intervals until the UPS either turns off or is no longer running on battery.
Status: current Access: read-write
NOTIFICATION-TYPE    

upsTrapTestCompleted 1.3.6.1.2.1.33.2.2
This trap is sent upon completion of a UPS diagnostic test.
Status: current Access: read-write
NOTIFICATION-TYPE    

upsTrapAlarmEntryAdded 1.3.6.1.2.1.33.2.3
This trap is sent each time an alarm is inserted into to the alarm table. It is sent on the insertion of all alarms except for upsAlarmOnBattery and upsAlarmTestInProgress.
Status: current Access: read-write
NOTIFICATION-TYPE    

upsTrapAlarmEntryRemoved 1.3.6.1.2.1.33.2.4
This trap is sent each time an alarm is removed from the alarm table. It is sent on the removal of all alarms except for upsAlarmTestInProgress.
Status: current Access: read-write
NOTIFICATION-TYPE    

upsConformance 1.3.6.1.2.1.33.3
OBJECT IDENTIFIER    

upsCompliances 1.3.6.1.2.1.33.3.1
OBJECT IDENTIFIER    

upsSubsetCompliance 1.3.6.1.2.1.33.3.1.1
The compliance statement for UPSs that only support the two-contact communication protocol.
Status: current Access: read-only
MODULE-COMPLIANCE    

upsBasicCompliance 1.3.6.1.2.1.33.3.1.2
The compliance statement for UPSs that support full-featured functions, such as control.
Status: current Access: read-only
MODULE-COMPLIANCE    

upsFullCompliance 1.3.6.1.2.1.33.3.1.3
The compliance statement for UPSs that support advanced full-featured functions.
Status: current Access: read-only
MODULE-COMPLIANCE    

upsGroups 1.3.6.1.2.1.33.3.2
OBJECT IDENTIFIER    

upsSubsetGroups 1.3.6.1.2.1.33.3.2.1
OBJECT IDENTIFIER    

upsSubsetIdentGroup 1.3.6.1.2.1.33.3.2.1.1
The upsSubsetIdentGroup defines objects which are common across all UPSs which meet subset compliance. Most devices which conform to the upsSubsetIdentGroup will provide access to these objects via a proxy agent. If the proxy agent is compatible with multiple UPS types, configuration of the proxy agent will require specifying some of these values, either individually, or as a group (perhaps through a table lookup mechanism based on the UPS model number).
Status: current Access: read-only
OBJECT-GROUP    

upsSubsetBatteryGroup 1.3.6.1.2.1.33.3.2.1.2
The upsSubsetBatteryGroup defines the objects that are common to battery groups of two-contact UPSs.
Status: current Access: read-only
OBJECT-GROUP    

upsSubsetInputGroup 1.3.6.1.2.1.33.3.2.1.3
The upsSubsetInputGroup defines the objects that are common to the Input groups of two-contact UPSs.
Status: current Access: read-only
OBJECT-GROUP    

upsSubsetOutputGroup 1.3.6.1.2.1.33.3.2.1.4
The upsSubsetOutputGroup defines the objects that are common to the Output groups of two-contact UPSs.
Status: current Access: read-only
OBJECT-GROUP    

upsSubsetAlarmGroup 1.3.6.1.2.1.33.3.2.1.6
The upsSubsetAlarmGroup defines the objects that are common to the Alarm groups of two-contact UPSs.
Status: current Access: read-only
OBJECT-GROUP    

upsSubsetControlGroup 1.3.6.1.2.1.33.3.2.1.8
The upsSubsetControlGroup defines the objects that are common to the Control groups of two-contact UPSs.
Status: current Access: read-only
OBJECT-GROUP    

upsSubsetConfigGroup 1.3.6.1.2.1.33.3.2.1.9
The upsSubsetConfigGroup defines the objects that are common to the Config groups of two-contact UPSs.
Status: current Access: read-only
OBJECT-GROUP    

upsBasicGroups 1.3.6.1.2.1.33.3.2.2
OBJECT IDENTIFIER    

upsBasicIdentGroup 1.3.6.1.2.1.33.3.2.2.1
The upsBasicIdentGroup defines objects which are common to the Ident group of compliant UPSs which support basic functions.
Status: current Access: read-only
OBJECT-GROUP    

upsBasicBatteryGroup 1.3.6.1.2.1.33.3.2.2.2
The upsBasicBatteryGroup defines the objects that are common to the battery groups of compliant UPSs which support basic functions.
Status: current Access: read-only
OBJECT-GROUP    

upsBasicInputGroup 1.3.6.1.2.1.33.3.2.2.3
The upsBasicInputGroup defines the objects that are common to the Input groups of compliant UPSs which support basic functions.
Status: current Access: read-only
OBJECT-GROUP    

upsBasicOutputGroup 1.3.6.1.2.1.33.3.2.2.4
The upsBasicOutputGroup defines the objects that are common to the Output groups of compliant UPSs which support basic functions.
Status: current Access: read-only
OBJECT-GROUP    

upsBasicBypassGroup 1.3.6.1.2.1.33.3.2.2.5
The upsBasicBypassGroup defines the objects that are common to the Bypass groups of compliant UPSs which support basic functions.
Status: current Access: read-only
OBJECT-GROUP    

upsBasicAlarmGroup 1.3.6.1.2.1.33.3.2.2.6
The upsBasicAlarmGroup defines the objects that are common to the Alarm groups of compliant UPSs which support basic functions.
Status: current Access: read-only
OBJECT-GROUP    

upsBasicTestGroup 1.3.6.1.2.1.33.3.2.2.7
The upsBasicTestGroup defines the objects that are common to the Test groups of compliant UPSs which support basic functions.
Status: current Access: read-only
OBJECT-GROUP    

upsBasicControlGroup 1.3.6.1.2.1.33.3.2.2.8
The upsBasicControlGroup defines the objects that are common to the Control groups of compliant UPSs which support basic functions.
Status: current Access: read-only
OBJECT-GROUP    

upsBasicConfigGroup 1.3.6.1.2.1.33.3.2.2.9
The upsBasicConfigGroup defines the objects that are common to the Config groups of UPSs which support basic functions.
Status: current Access: read-only
OBJECT-GROUP    

upsFullGroups 1.3.6.1.2.1.33.3.2.3
OBJECT IDENTIFIER    

upsFullIdentGroup 1.3.6.1.2.1.33.3.2.3.1
The upsFullIdentGroup defines objects which are common to the Ident group of fully compliant UPSs.
Status: current Access: read-only
OBJECT-GROUP    

upsFullBatteryGroup 1.3.6.1.2.1.33.3.2.3.2
The upsFullBatteryGroup defines the objects that are common to the battery groups of fully compliant UPSs.
Status: current Access: read-only
OBJECT-GROUP    

upsFullInputGroup 1.3.6.1.2.1.33.3.2.3.3
The upsFullInputGroup defines the objects that are common to the Input groups of fully compliant UPSs.
Status: current Access: read-only
OBJECT-GROUP    

upsFullOutputGroup 1.3.6.1.2.1.33.3.2.3.4
The upsFullOutputGroup defines the objects that are common to the Output groups of fully compliant UPSs.
Status: current Access: read-only
OBJECT-GROUP    

upsFullBypassGroup 1.3.6.1.2.1.33.3.2.3.5
The upsFullBypassGroup defines the objects that are common to the Bypass groups of fully compliant UPSs.
Status: current Access: read-only
OBJECT-GROUP    

upsFullAlarmGroup 1.3.6.1.2.1.33.3.2.3.6
The upsFullAlarmGroup defines the objects that are common to the Alarm groups of fully compliant UPSs.
Status: current Access: read-only
OBJECT-GROUP    

upsFullTestGroup 1.3.6.1.2.1.33.3.2.3.7
The upsFullTestGroup defines the objects that are common to the Test groups of fully compliant UPSs.
Status: current Access: read-only
OBJECT-GROUP    

upsFullControlGroup 1.3.6.1.2.1.33.3.2.3.8
The upsFullControlGroup defines the objects that are common to the Control groups of fully compliant UPSs.
Status: current Access: read-only
OBJECT-GROUP    

upsFullConfigGroup 1.3.6.1.2.1.33.3.2.3.9
The upsFullConfigGroup defines the objects that are common to the Config groups of fully compliant UPSs.
Status: current Access: read-only
OBJECT-GROUP