TIMETRA-OAM-PM-MIB

File: TIMETRA-OAM-PM-MIB.mib (306601 bytes)

Imported modules

IEEE8021-CFM-MIB INET-ADDRESS-MIB SNMPv2-CONF
SNMPv2-SMI SNMPv2-TC TIMETRA-GLOBAL-MIB
TIMETRA-SERV-MIB TIMETRA-TC-MIB

Imported symbols

Dot1agCfmMepIdOrZero InetAddress InetAddressPrefixLength
InetAddressType InetPortNumber MODULE-COMPLIANCE
NOTIFICATION-GROUP OBJECT-GROUP MODULE-IDENTITY
NOTIFICATION-TYPE OBJECT-TYPE Counter32
Counter64 Integer32 Unsigned32
DateAndTime MacAddress RowStatus
TEXTUAL-CONVENTION TimeStamp TruthValue
timetraSRMIBModules tmnxSRConfs tmnxSRNotifyPrefix
tmnxSRObjs svcId TFCName
TItemDescription TNamedItem TNamedItemOrEmpty
TmnxEnabledDisabled TmnxEnabledDisabledOrNA TmnxOperState
TProfile

Defined Types

TmnxOamPmBinGroupId  
An object of type TmnxOamPmBinGroupId identifies an OAM Performance Monitoring bin group.
TEXTUAL-CONVENTION    
  Unsigned32 1..255  

TmxnOamPmBinNums  
An object of type TmxnOamPmBinNums specifies a set of OAM Performance Monitoring delay bin numbers.
TEXTUAL-CONVENTION    
  BITS bin0(0), bin1(1), bin2(2), bin3(3), bin4(4), bin5(5), bin6(6), bin7(7), bin8(8), bin9(9)  

TmnxOamPmBinType  
An object of type TmnxOamPmBinType specifies the type of an OAM Performance Monitoring bin. Values: fd(1) A Frame Delay (FD) bin, as defined in MEF-35. fdr(2) A Frame Delay Range (FDR) bin, as defined in MEF-35. ifdv(3) An Inter-Frame Delay Variation (IFDV) bin, as defined in MEF-35.
TEXTUAL-CONVENTION    
  INTEGER fd(1), fdr(2), ifdv(3)  

TmnxOamPmCfgBinNum  
An object of type TmnxOamPmCfgBinNum specifies the bin number of a configurable OAM Performance Monitoring delay bin. Bin zero is defined, but it is not configurable.
TEXTUAL-CONVENTION    
  Unsigned32 1..9  

TmnxOamPmCfgBinNumOrNone  
An object of type TmnxOamPmCfgBinNumOrNone specifies the bin number of a configurable OAM Performance Monitoring delay bin, or indicates that no bin is specified. Bin zero is defined, but it is not configurable.
TEXTUAL-CONVENTION    
  Integer32 -1 | 1..9  

TmnxOamPmDetectableTxError  
An object of type TmnxOamPmDetectableTxError indicates the reason for the inability (if any) to launch test frames for the specified test. The code points are as follows. none (1) - no transmit failure has been detected txPortDown (2) - the transmit port is operationally down noTxPort (3) - an egress has not been found ethParentAdminDown (4) - the parent (e.g. the SAP, SDP, service, or port) of the MEP is administratively down ethNoMepOrAdminDown (5) - the test's MEP is not fully configured or the MEP is administratively down unexpectedError (6) - transmission failed due to unexpected conditions, such as failed memory allocation, traffic congestion, or failure to obtain the necessary resources noService (7) - the service associated with this test session was not found serviceAdminDown (8) - the service associated with this test session is administratively down serviceOperDown (9) - the service associated with this test session is operationally down noRoute (10) - there is no IP route to the destination address noInterface (11) - there is no IP interface that matches the configured forwarding interface noDirectInterface (12) - there is no appropriate IP interface for bypass-routing to the destination address sourceInterfaceDown (13) - the IP interface associated with the source address is down sourceIpNotLocal (14) - the source address is not local nextHopIpIsLocal (15) - the next-hop address is local
TEXTUAL-CONVENTION    
  INTEGER none(1), txPortDown(2), noTxPort(3), ethParentAdminDown(4), ethNoMepOrAdminDown(5), unexpectedError(6), noService(7), serviceAdminDown(8), serviceOperDown(9), noRoute(10), noInterface(11), noDirectInterface(12), sourceInterfaceDown(13), sourceIpNotLocal(14), nextHopIpIsLocal(15)  

TmnxOamPmForwardBackward  
An object of type TmnxOamPmForwardBackward specifies the MEF-35 traffic flow direction of an OAM-PM loss test. The code points are as follows. forward (1) - refers to the loss of traffic flowing away from the test originator. backward (2) - refers to the loss of traffic flowing toward the test originator.
TEXTUAL-CONVENTION    
  INTEGER forward(1), backward(2)  

TmnxOamPmForwardBackwardAggr  
An object of type TmnxOamPmForwardBackwardAggr specifies the traffic flow direction type of an OAM-PM loss threshold. The code points are as follows. forward (1) - apply the threshold to the counter for traffic flowing away from the test originator. backward (2) - apply the threshold to the counter for traffic flowing toward the test originator. aggregate(3) - apply the threshold to the sum of the forward and backward counters.
TEXTUAL-CONVENTION    
  INTEGER forward(1), backward(2), aggregate(3)  

TmnxOamPmForwardBackwardTwoWay  
An object of type TmnxOamPmForwardBackwardTwoWay specifies the MEF-35 traffic flow direction of an OAM-PM delay test. The code points are as follows. forward (1) - refers to the one-way delay of traffic flowing away from the test originator. backward (2) - refers to the one-way delay of traffic flowing toward the test originator. twoWay (3) - refers to two way delay.
TEXTUAL-CONVENTION    
  INTEGER forward(1), backward(2), twoWay(3)  

TmnxOamPmMeasIntervalDuration  
An object of type TmnxOamPmMeasIntervalDuration specifies the duration of an OAM Performance Monitoring measurement interval. Values: miRaw(1) A raw measurement interval starts when the associated test starts, and ends when the associated test ends. mi15Minutes(2) A 15 minute measurement interval, as defined in MEF-35 Section 9.1.6. mi1Hour(3) A one hour measurement interval. mi1Day(4) A one day measurement interval. mi5Minutes(5) A five minute measurement interval.
TEXTUAL-CONVENTION    
  INTEGER miRaw(1), mi15Minutes(2), mi1Hour(3), mi1Day(4), mi5Minutes(5)  

TmnxOamPmCfgMeasIntervalDuration  
An object of type TmnxOamPmCfgMeasIntervalDuration specifies the duration of a configurable OAM Performance Monitoring measurement interval. This TEXTUAL-CONVENTION is the same as TmnxOamPmMeasIntervalDuration, except the 'miRaw(1)' code point is absent here (because raw measurement intervals are not configurable).
TEXTUAL-CONVENTION    
  INTEGER mi15Minutes(2), mi1Hour(3), mi1Day(4), mi5Minutes(5)  

TmnxOamPmSessionType  
An object of type TmnxOamPmSessionType specifies the type of an OAM Performance Monitoring session. Values: proactive(1) Test the service using a proactive session, as specified in MEF-35 Section 9.1.2. onDemand(2) Test the service using an on-demand session, as specified in MEF-35 Section 9.1.2.
TEXTUAL-CONVENTION    
  INTEGER proactive(1), onDemand(2)  

TmnxOamPmStsIntvlNum  
An object of type TmnxOamPmStsIntvlNum specifies the interval number of a Measurement Interval Data Set.
TEXTUAL-CONVENTION    
  Unsigned32 1..4294967295  

TmnxOamPmStsTcaOperState  
An object of type TmnxOamPmStsTcaOperState indicates the operational state of the Threshold Crossing Alerts (TCAs) for the specified indices. The code points are as follows. The conditions are evaluated in the order shown. pending(1) 'pending(1)' is returned if the threshold configuration for the specified indices changed during the current measurement interval. active(2) If the specified indices have a default clear threshold configured, 'active(2)' is returned if the current measurement interval has generated a Raise TCA (i.e. tmnxOamPmThrRaise). If the specified indices have a non-default clear threshold configured, 'active(2)' is returned if the most recent TCA generated was a Raise (i.e. tmnxOamPmThrRaise). notActive(3) 'notActive(3)' is returned for all other conditions (e.g. thresholding is not configured for the specified indices).
TEXTUAL-CONVENTION    
  INTEGER pending(1), active(2), notActive(3)  

TmnxOamPmTestFamily  
An object of type TmnxOamPmTestFamily specifies the type of the service to be tested by an OAM Performance Monitoring test. Values: ethernet(1) Test an Ethernet service, as specified in MEF-35 Section 7. ip(2) Test an IP service.
TEXTUAL-CONVENTION    
  INTEGER ethernet(1), ip(2)  

TmnxOamPmTestType  
An object of type TmnxOamPmTestType specifies the type of an OAM Performance Monitoring test. Values: dmm(1) A Delay Measurement test, as specified in MEF-35 Section 10.1. slm(2) A Synthetic Loss Measurement test, as specified in MEF-35 Section 10.2. twampLight(3) A TWAMP-Light delay and/or loss test, using the TWAMP-Light protocol defined in RFC 5357, Appendix I. lmm(4) An ETH-LM test, as specified in Y.1731 Section 8.1.
TEXTUAL-CONVENTION    
  INTEGER dmm(1), slm(2), twampLight(3), lmm(4)  

TmnxOamPmCfgBinGroupEntry  
SEQUENCE    
  tmnxOamPmCfgBinGroupId TmnxOamPmBinGroupId
  tmnxOamPmCfgBinGroupRowStatus RowStatus
  tmnxOamPmCfgBinGroupAdminStatus TmnxEnabledDisabled
  tmnxOamPmCfgBinGroupDescription TItemDescription
  tmnxOamPmCfgBinGroupFdBinCount Unsigned32
  tmnxOamPmCfgBinGroupFdrBinCount Unsigned32
  tmnxOamPmCfgBinGroupIfdvBinCount Unsigned32

TmnxOamPmCfgBinEntry  
SEQUENCE    
  tmnxOamPmCfgBinType TmnxOamPmBinType
  tmnxOamPmCfgBinNum TmnxOamPmCfgBinNum
  tmnxOamPmCfgBinLowerBound Unsigned32

TmnxOamPmCfgSessEntry  
SEQUENCE    
  tmnxOamPmCfgSessName TNamedItem
  tmnxOamPmCfgSessRowStatus RowStatus
  tmnxOamPmCfgSessTestFamily TmnxOamPmTestFamily
  tmnxOamPmCfgSessType TmnxOamPmSessionType
  tmnxOamPmCfgSessBinGroupId TmnxOamPmBinGroupId
  tmnxOamPmCfgSessDescription TItemDescription

TmnxOamPmCfgSessEthEntry  
SEQUENCE    
  tmnxOamPmCfgSessEthSrcMepId Dot1agCfmMepIdOrZero
  tmnxOamPmCfgSessEthSrcMdIndex Unsigned32
  tmnxOamPmCfgSessEthSrcMaIndex Unsigned32
  tmnxOamPmCfgSessEthPriority Unsigned32
  tmnxOamPmCfgSessEthDestMacAddr MacAddress

TmnxOamPmCfgDelayDmmEntry  
SEQUENCE    
  tmnxOamPmCfgDelayDmmRowStatus RowStatus
  tmnxOamPmCfgDelayDmmAdminStatus TmnxEnabledDisabled
  tmnxOamPmCfgDelayDmmOnDmndStatus TmnxEnabledDisabledOrNA
  tmnxOamPmCfgDelayDmmTestId Unsigned32
  tmnxOamPmCfgDelayDmmInterval Unsigned32
  tmnxOamPmCfgDelayDmmDataTlvSize Unsigned32
  tmnxOamPmCfgDelayDmmTestDuration Unsigned32
  tmnxOamPmCfgDelayDmmRunTimeLeft Unsigned32

TmnxOamPmCfgLossSlmEntry  
SEQUENCE    
  tmnxOamPmCfgLossSlmRowStatus RowStatus
  tmnxOamPmCfgLossSlmAdminStatus TmnxEnabledDisabled
  tmnxOamPmCfgLossSlmOnDmndStatus TmnxEnabledDisabledOrNA
  tmnxOamPmCfgLossSlmTestId Unsigned32
  tmnxOamPmCfgLossSlmInterval Unsigned32
  tmnxOamPmCfgLossSlmDataTlvSize Unsigned32
  tmnxOamPmCfgLossSlmTxFrmsPerDelT Unsigned32
  tmnxOamPmCfgLossSlmConsecDeltaTs Unsigned32
  tmnxOamPmCfgLossSlmChliThreshold Unsigned32
  tmnxOamPmCfgLossSlmFlrThreshold Unsigned32
  tmnxOamPmCfgLossSlmTestDuration Unsigned32
  tmnxOamPmCfgLossSlmRunTimeLeft Unsigned32

TmnxOamPmCfgMeasIntvlEntry  
SEQUENCE    
  tmnxOamPmCfgMeasIntvlDuration TmnxOamPmCfgMeasIntervalDuration
  tmnxOamPmCfgMeasIntvlRowStatus RowStatus
  tmnxOamPmCfgMeasIntvlAccntPolicy Unsigned32
  tmnxOamPmCfgMeasIntvlsStored Unsigned32
  tmnxOamPmCfgMeasIntvlBoundaryTyp INTEGER
  tmnxOamPmCfgMeasIntvlClockOffset Unsigned32
  tmnxOamPmCfgMeasIntvlDelayTCAs TmnxEnabledDisabled
  tmnxOamPmCfgMeasIntvlLossTCAs TmnxEnabledDisabled
  tmnxOamPmCfgMeasIntvlTCAs TmnxEnabledDisabled

TmnxOamPmCfgSessIpEntry  
SEQUENCE    
  tmnxOamPmCfgSessIpServiceId Unsigned32
  tmnxOamPmCfgSessIpSrcAddressType InetAddressType
  tmnxOamPmCfgSessIpSrcAddress InetAddress
  tmnxOamPmCfgSessIpDstAddressType InetAddressType
  tmnxOamPmCfgSessIpDstAddress InetAddress
  tmnxOamPmCfgSessIpDstUdpPort InetPortNumber
  tmnxOamPmCfgSessIpBypassRouting TruthValue
  tmnxOamPmCfgSessIpEgressIfName TNamedItemOrEmpty
  tmnxOamPmCfgSessIpNhAddressType InetAddressType
  tmnxOamPmCfgSessIpNhAddress InetAddress
  tmnxOamPmCfgSessIpForwardClass TFCName
  tmnxOamPmCfgSessIpProfile TProfile
  tmnxOamPmCfgSessIpTtl Unsigned32
  tmnxOamPmCfgSessIpSrcUdpPort InetPortNumber

TmnxOamPmCfgTwampLtEntry  
SEQUENCE    
  tmnxOamPmCfgTwampLtRowStatus RowStatus
  tmnxOamPmCfgTwampLtAdminStatus TmnxEnabledDisabled
  tmnxOamPmCfgTwampLtOnDmndStatus TmnxEnabledDisabledOrNA
  tmnxOamPmCfgTwampLtTestId Unsigned32
  tmnxOamPmCfgTwampLtInterval Unsigned32
  tmnxOamPmCfgTwampLtPadSize Unsigned32
  tmnxOamPmCfgTwampLtTestDuration Unsigned32
  tmnxOamPmCfgTwampLtRunTimeLeft Unsigned32
  tmnxOamPmCfgTwampLtCollectStats INTEGER
  tmnxOamPmCfgTwampLtTxFrmsPerDelT Unsigned32
  tmnxOamPmCfgTwampLtConsecDeltaTs Unsigned32
  tmnxOamPmCfgTwampLtChliThreshold Unsigned32
  tmnxOamPmCfgTwampLtFlrThreshold Unsigned32

TmnxOamPmCfgTwlRflEntry  
SEQUENCE    
  tmnxOamPmCfgTwlRflRowStatus RowStatus
  tmnxOamPmCfgTwlRflAdminStatus TmnxEnabledDisabled
  tmnxOamPmCfgTwlRflDescription TItemDescription
  tmnxOamPmCfgTwlRflListenUdpPort Unsigned32

TmnxOamPmCfgTwlRflPfxEntry  
SEQUENCE    
  tmnxOamPmCfgTwlRflPfxPrefixType InetAddressType
  tmnxOamPmCfgTwlRflPfxPrefix InetAddress
  tmnxOamPmCfgTwlRflPfxPrefixLen InetAddressPrefixLength
  tmnxOamPmCfgTwlRflPfxRowStatus RowStatus
  tmnxOamPmCfgTwlRflPfxDescription TItemDescription

TmnxOamPmCfgLossLmmEntry  
SEQUENCE    
  tmnxOamPmCfgLossLmmRowStatus RowStatus
  tmnxOamPmCfgLossLmmAdminStatus TmnxEnabledDisabled
  tmnxOamPmCfgLossLmmOnDmndStatus TmnxEnabledDisabledOrNA
  tmnxOamPmCfgLossLmmTestId Unsigned32
  tmnxOamPmCfgLossLmmInterval Unsigned32
  tmnxOamPmCfgLossLmmTestDuration Unsigned32
  tmnxOamPmCfgLossLmmRunTimeLeft Unsigned32
  tmnxOamPmCfgLossLmmTxFrmsPerDelT Unsigned32
  tmnxOamPmCfgLossLmmConsecDeltaTs Unsigned32
  tmnxOamPmCfgLossLmmChliThreshold Unsigned32
  tmnxOamPmCfgLossLmmFlrThreshold Unsigned32
  tmnxOamPmCfgLossLmmAvAdminStatus TmnxEnabledDisabled

TmnxOamPmCfgThrLossFwBwEntry  
SEQUENCE    
  tmnxOamPmCfgTestType TmnxOamPmTestType
  tmnxOamPmCfgForwardBackward TmnxOamPmForwardBackward
  tmnxOamPmCfgThrLossAvgFlrRaise Integer32
  tmnxOamPmCfgThrLossAvgFlrClear Integer32

TmnxOamPmCfgThrLossFwBwAgEntry  
SEQUENCE    
  tmnxOamPmCfgForwardBackwardAggr TmnxOamPmForwardBackwardAggr
  tmnxOamPmCfgThrLossChliRaise Integer32
  tmnxOamPmCfgThrLossChliClear Integer32
  tmnxOamPmCfgThrLossHliRaise Integer32
  tmnxOamPmCfgThrLossHliClear Integer32
  tmnxOamPmCfgThrLossUnavlIndRaise Integer32
  tmnxOamPmCfgThrLossUnavlIndClear Integer32
  tmnxOamPmCfgThrLossUndtAvlRaise Integer32
  tmnxOamPmCfgThrLossUndtAvlClear Integer32
  tmnxOamPmCfgThrLossUndtUnavlRais Integer32
  tmnxOamPmCfgThrLossUndtUnavlClr Integer32

TmnxOamPmCfgThrDelayEntry  
SEQUENCE    
  tmnxOamPmCfgForwardBackward2Way TmnxOamPmForwardBackwardTwoWay
  tmnxOamPmCfgThrDelayLowestBin Unsigned32
  tmnxOamPmCfgThrDelayRaise Integer32
  tmnxOamPmCfgThrDelayClear Integer32
  tmnxOamPmCfgThrDelayExclBinFrTca TmnxOamPmCfgBinNumOrNone

TmnxOamPmCfgBinGrpTypeDirEntry  
SEQUENCE    
  tmnxOamPmCfgBgTyDirExclBinsFrAvg TmxnOamPmBinNums

TmnxOamPmStsBaseEntry  
SEQUENCE    
  tmnxOamPmStsBaseTestType TmnxOamPmTestType
  tmnxOamPmStsMeasIntvlDuration TmnxOamPmMeasIntervalDuration
  tmnxOamPmStsIntvlNum TmnxOamPmStsIntvlNum
  tmnxOamPmStsBaseOperStatus INTEGER
  tmnxOamPmStsBaseSuspect TruthValue
  tmnxOamPmStsBaseStartTime DateAndTime
  tmnxOamPmStsBaseElapsedTime Unsigned32
  tmnxOamPmStsBaseTestFramesTx Unsigned32
  tmnxOamPmStsBaseTestFramesRx Unsigned32

TmnxOamPmStsMeasIntvlIndexEntry  
SEQUENCE    
  tmnxOamPmStsMeasIntvlIndexNewest TmnxOamPmStsIntvlNum

TmnxOamPmStsLossSlmEntry  
SEQUENCE    
  tmnxOamPmStsLossSlmTxFwd Unsigned32
  tmnxOamPmStsLossSlmRxFwd Unsigned32
  tmnxOamPmStsLossSlmTxBwd Unsigned32
  tmnxOamPmStsLossSlmRxBwd Unsigned32
  tmnxOamPmStsLossSlmAvailIndFwd Unsigned32
  tmnxOamPmStsLossSlmAvailIndBwd Unsigned32
  tmnxOamPmStsLossSlmUnavlIndFwd Unsigned32
  tmnxOamPmStsLossSlmUnavlIndBwd Unsigned32
  tmnxOamPmStsLossSlmUndtAvlFwd Unsigned32
  tmnxOamPmStsLossSlmUndtUnavlFwd Unsigned32
  tmnxOamPmStsLossSlmUndtAvlBwd Unsigned32
  tmnxOamPmStsLossSlmUndtUnavlBwd Unsigned32
  tmnxOamPmStsLossSlmHliFwd Unsigned32
  tmnxOamPmStsLossSlmHliBwd Unsigned32
  tmnxOamPmStsLossSlmChliFwd Unsigned32
  tmnxOamPmStsLossSlmChliBwd Unsigned32
  tmnxOamPmStsLossSlmMinFlrFwd Unsigned32
  tmnxOamPmStsLossSlmMaxFlrFwd Unsigned32
  tmnxOamPmStsLossSlmAvgFlrFwd Unsigned32
  tmnxOamPmStsLossSlmMinFlrBwd Unsigned32
  tmnxOamPmStsLossSlmMaxFlrBwd Unsigned32
  tmnxOamPmStsLossSlmAvgFlrBwd Unsigned32

TmnxOamPmStsDelayDmmEntry  
SEQUENCE    
  tmnxOamPmStsDelayDmmFwdMin Unsigned32
  tmnxOamPmStsDelayDmmFwdMax Unsigned32
  tmnxOamPmStsDelayDmmFwdAvg Unsigned32
  tmnxOamPmStsDelayDmmBwdMin Unsigned32
  tmnxOamPmStsDelayDmmBwdMax Unsigned32
  tmnxOamPmStsDelayDmmBwdAvg Unsigned32
  tmnxOamPmStsDelayDmm2wyMin Unsigned32
  tmnxOamPmStsDelayDmm2wyMax Unsigned32
  tmnxOamPmStsDelayDmm2wyAvg Unsigned32

TmnxOamPmStsDelayDmmBinEntry  
SEQUENCE    
  tmnxOamPmStsDelayDmmBinNum Unsigned32
  tmnxOamPmStsDelayDmmBinFwdCount Unsigned32
  tmnxOamPmStsDelayDmmBinBwdCount Unsigned32
  tmnxOamPmStsDelayDmmBin2wyCount Unsigned32

TmnxOamPmStsTwlRflEntry  
SEQUENCE    
  tmnxOamPmStsTwlRflUpTime Unsigned32
  tmnxOamPmStsTwlRflFramesRx Unsigned32
  tmnxOamPmStsTwlRflFramesTx Unsigned32

TmnxOamPmStsDelayTwlEntry  
SEQUENCE    
  tmnxOamPmStsDelayTwlFwdMin Unsigned32
  tmnxOamPmStsDelayTwlFwdMax Unsigned32
  tmnxOamPmStsDelayTwlFwdAvg Unsigned32
  tmnxOamPmStsDelayTwlBwdMin Unsigned32
  tmnxOamPmStsDelayTwlBwdMax Unsigned32
  tmnxOamPmStsDelayTwlBwdAvg Unsigned32
  tmnxOamPmStsDelayTwl2wyMin Unsigned32
  tmnxOamPmStsDelayTwl2wyMax Unsigned32
  tmnxOamPmStsDelayTwl2wyAvg Unsigned32

TmnxOamPmStsDelayTwlBinEntry  
SEQUENCE    
  tmnxOamPmStsDelayTwlBinNum Unsigned32
  tmnxOamPmStsDelayTwlBinFwdCount Unsigned32
  tmnxOamPmStsDelayTwlBinBwdCount Unsigned32
  tmnxOamPmStsDelayTwlBin2wyCount Unsigned32

TmnxOamPmStsLossLmmEntry  
SEQUENCE    
  tmnxOamPmStsLossLmmTxFwd Counter64
  tmnxOamPmStsLossLmmRxFwd Counter64
  tmnxOamPmStsLossLmmTxBwd Counter64
  tmnxOamPmStsLossLmmRxBwd Counter64
  tmnxOamPmStsLossLmmMinFlrFwd Unsigned32
  tmnxOamPmStsLossLmmMaxFlrFwd Unsigned32
  tmnxOamPmStsLossLmmAvgFlrFwd Unsigned32
  tmnxOamPmStsLossLmmMinFlrBwd Unsigned32
  tmnxOamPmStsLossLmmMaxFlrBwd Unsigned32
  tmnxOamPmStsLossLmmAvgFlrBwd Unsigned32
  tmnxOamPmStsLossLmmAvailIndFwd Counter32
  tmnxOamPmStsLossLmmAvailIndBwd Counter32
  tmnxOamPmStsLossLmmUnavlIndFwd Counter32
  tmnxOamPmStsLossLmmUnavlIndBwd Counter32
  tmnxOamPmStsLossLmmUndtAvlFwd Counter32
  tmnxOamPmStsLossLmmUndtUnavlFwd Counter32
  tmnxOamPmStsLossLmmUndtAvlBwd Counter32
  tmnxOamPmStsLossLmmUndtUnavlBwd Counter32
  tmnxOamPmStsLossLmmHliFwd Counter32
  tmnxOamPmStsLossLmmHliBwd Counter32
  tmnxOamPmStsLossLmmChliFwd Counter32
  tmnxOamPmStsLossLmmChliBwd Counter32
  tmnxOamPmStsLossLmmUndetDelTsFwd Counter32
  tmnxOamPmStsLossLmmUndetDelTsBwd Counter32

TmnxOamPmStsLossTwlEntry  
SEQUENCE    
  tmnxOamPmStsLossTwlTxFwd Counter32
  tmnxOamPmStsLossTwlRxFwd Counter32
  tmnxOamPmStsLossTwlTxBwd Counter32
  tmnxOamPmStsLossTwlRxBwd Counter32
  tmnxOamPmStsLossTwlAvailIndFwd Counter32
  tmnxOamPmStsLossTwlAvailIndBwd Counter32
  tmnxOamPmStsLossTwlUnavlIndFwd Counter32
  tmnxOamPmStsLossTwlUnavlIndBwd Counter32
  tmnxOamPmStsLossTwlUndtAvlFwd Counter32
  tmnxOamPmStsLossTwlUndtUnavlFwd Counter32
  tmnxOamPmStsLossTwlUndtAvlBwd Counter32
  tmnxOamPmStsLossTwlUndtUnavlBwd Counter32
  tmnxOamPmStsLossTwlHliFwd Counter32
  tmnxOamPmStsLossTwlHliBwd Counter32
  tmnxOamPmStsLossTwlChliFwd Counter32
  tmnxOamPmStsLossTwlChliBwd Counter32
  tmnxOamPmStsLossTwlMinFlrFwd Unsigned32
  tmnxOamPmStsLossTwlMaxFlrFwd Unsigned32
  tmnxOamPmStsLossTwlAvgFlrFwd Unsigned32
  tmnxOamPmStsLossTwlMinFlrBwd Unsigned32
  tmnxOamPmStsLossTwlMaxFlrBwd Unsigned32
  tmnxOamPmStsLossTwlAvgFlrBwd Unsigned32

TmnxOamPmStsTcaDelayEntry  
SEQUENCE    
  tmnxOamPmStsTcaDelayLastTime DateAndTime
  tmnxOamPmStsTcaDelayOperState TmnxOamPmStsTcaOperState

TmnxOamPmStsTcaLossFwBwAgEntry  
SEQUENCE    
  tmnxOamPmStsTcaLossChliLastTime DateAndTime
  tmnxOamPmStsTcaLossChliOperState TmnxOamPmStsTcaOperState
  tmnxOamPmStsTcaLossHliLastTime DateAndTime
  tmnxOamPmStsTcaLossHliOperState TmnxOamPmStsTcaOperState
  tmnxOamPmStsTcaLossUnavlIndLTime DateAndTime
  tmnxOamPmStsTcaLossUnavlIndOprSt TmnxOamPmStsTcaOperState
  tmnxOamPmStsTcaLossUndtAvlLTime DateAndTime
  tmnxOamPmStsTcaLossUndtAvlOperSt TmnxOamPmStsTcaOperState
  tmnxOamPmStsTcaLossUndtUnavlLTim DateAndTime
  tmnxOamPmStsTcaLossUndtUnavlOpSt TmnxOamPmStsTcaOperState

TmnxOamPmStsTcaLossFwBwEntry  
SEQUENCE    
  tmnxOamPmStsTcaLossAvgFlrLstTime DateAndTime
  tmnxOamPmStsTcaLossAvgFlrOperSt TmnxOamPmStsTcaOperState

TmnxOamPmStsSessIpEntry  
SEQUENCE    
  tmnxOamPmStsSessIpSrcUdpPort InetPortNumber

TmnxOamPmStsTestEntry  
SEQUENCE    
  tmnxOamPmStsTestDetectTxError TmnxOamPmDetectableTxError

Defined Values

timetraOamPmMIBModule 1.3.6.1.4.1.6527.1.1.3.92
This document is the SNMP MIB module for the Nokia SROS implementation of Service OAM Performance Monitoring. Copyright 2013-2016 Nokia. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Nokia's proprietary intellectual property. Nokia retains all title and ownership in the Specification, including any revisions. Nokia grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Nokia products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied `as is', and Nokia makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
MODULE-IDENTITY    

tmnxOamPmObjs 1.3.6.1.4.1.6527.3.1.2.92
OBJECT IDENTIFIER    

tmnxOamPmCfgObjs 1.3.6.1.4.1.6527.3.1.2.92.1
OBJECT IDENTIFIER    

tmnxOamPmCfgScalarObjs 1.3.6.1.4.1.6527.3.1.2.92.1.1
OBJECT IDENTIFIER    

tmnxOamPmTableLastChgObjs 1.3.6.1.4.1.6527.3.1.2.92.1.2
OBJECT IDENTIFIER    

tmnxOamPmCfgTableObjs 1.3.6.1.4.1.6527.3.1.2.92.1.3
OBJECT IDENTIFIER    

tmnxOamPmStatsObjs 1.3.6.1.4.1.6527.3.1.2.92.2
OBJECT IDENTIFIER    

tmnxOamPmStatsScalarObjs 1.3.6.1.4.1.6527.3.1.2.92.2.1
OBJECT IDENTIFIER    

tmnxOamPmStatsTableObjs 1.3.6.1.4.1.6527.3.1.2.92.2.2
OBJECT IDENTIFIER    

tmnxOamPmNotificationObjs 1.3.6.1.4.1.6527.3.1.2.92.3
OBJECT IDENTIFIER    

tmnxOamPmNotifyPrefix 1.3.6.1.4.1.6527.3.1.3.92
OBJECT IDENTIFIER    

tmnxOamPmNotifications 1.3.6.1.4.1.6527.3.1.3.92.0
OBJECT IDENTIFIER    

tmnxOamPmConformance 1.3.6.1.4.1.6527.3.1.1.92
OBJECT IDENTIFIER    

tmnxOamPmCompliances 1.3.6.1.4.1.6527.3.1.1.92.1
OBJECT IDENTIFIER    

tmnxOamPmObjGroups 1.3.6.1.4.1.6527.3.1.1.92.2
OBJECT IDENTIFIER    

tmnxOamPmV12v0ObjGroups 1.3.6.1.4.1.6527.3.1.1.92.2.1
OBJECT IDENTIFIER    

tmnxOamPmV13v0ObjGroups 1.3.6.1.4.1.6527.3.1.1.92.2.2
OBJECT IDENTIFIER    

tmnxOamPmV14v0ObjGroups 1.3.6.1.4.1.6527.3.1.1.92.2.3
OBJECT IDENTIFIER    

tmnxOamPmNotifGroups 1.3.6.1.4.1.6527.3.1.1.92.3
OBJECT IDENTIFIER    

tmnxOamPmV12v0NotifGroups 1.3.6.1.4.1.6527.3.1.1.92.3.1
OBJECT IDENTIFIER    

tmnxOamPmV13v0NotifGroups 1.3.6.1.4.1.6527.3.1.1.92.3.2
OBJECT IDENTIFIER    

tmnxOamPmNfyObjGroups 1.3.6.1.4.1.6527.3.1.1.92.4
OBJECT IDENTIFIER    

tmnxOamPmV12v0NfyObjGroups 1.3.6.1.4.1.6527.3.1.1.92.4.1
OBJECT IDENTIFIER    

tmnxOamPmV13v0NfyObjGroups 1.3.6.1.4.1.6527.3.1.1.92.4.2
OBJECT IDENTIFIER    

tmnxOamPmV14v0NfyObjGroups 1.3.6.1.4.1.6527.3.1.1.92.4.3
OBJECT IDENTIFIER    

tmnxOamPmCfgTwlRflInactTimer 1.3.6.1.4.1.6527.3.1.2.92.1.1.1
The value of tmnxOamPmCfgTwlRflInactTimer specifies the system inactivity timeout for TWAMP-Light reflectors. A TWAMP-Light reflector replies to TWAMP-Test PDUs. When a reflector sees a TWAMP-Test PDU for a new session (i.e. a {source IP address, source UDP port, destination IP address} triple which is not known to the reflector), the reflector allocates a record for the session. The record is used to ensure that reply PDUs sent for the session have consecutive sequence numbers. When a reflector sees tmnxOamPmCfgTwlRflInactTimer seconds pass without receiving a TWAMP-Test PDU for a particular session, an inactivity timeout has occurred, so the record allocated to the session is freed.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 10..100  

tmnxOamPmCfgBinGroupTableLastChg 1.3.6.1.4.1.6527.3.1.2.92.1.2.1
The value of tmnxOamPmCfgBinGroupTableLastChg indicates the time, since system startup, when tmnxOamPmCfgBinGroupTable last changed. If tmnxOamPmCfgBinGroupTable has not changed since system startup, zero is returned.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxOamPmCfgBinTableLastChg 1.3.6.1.4.1.6527.3.1.2.92.1.2.2
The value of tmnxOamPmCfgBinTableLastChg indicates the time, since system startup, when tmnxOamPmCfgBinTable last changed. If tmnxOamPmCfgBinTable has not changed since system startup, zero is returned.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxOamPmCfgSessTableLastChg 1.3.6.1.4.1.6527.3.1.2.92.1.2.3
The value of tmnxOamPmCfgSessTableLastChg indicates the time, since system startup, when tmnxOamPmCfgSessTable last changed. If tmnxOamPmCfgSessTable has not changed since system startup, zero is returned.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxOamPmCfgSessEthTableLastChg 1.3.6.1.4.1.6527.3.1.2.92.1.2.4
The value of tmnxOamPmCfgSessEthTableLastChg indicates the time, since system startup, when tmnxOamPmCfgSessEthTable last changed. If tmnxOamPmCfgSessEthTable has not changed since system startup, zero is returned.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxOamPmCfgDelayDmmTableLastChg 1.3.6.1.4.1.6527.3.1.2.92.1.2.5
The value of tmnxOamPmCfgDelayDmmTableLastChg indicates the time, since system startup, when tmnxOamPmCfgDelayDmmTable last changed. If tmnxOamPmCfgDelayDmmTable has not changed since system startup, zero is returned.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxOamPmCfgLossSlmTableLastChg 1.3.6.1.4.1.6527.3.1.2.92.1.2.6
The value of tmnxOamPmCfgLossSlmTableLastChg indicates the time, since system startup, when tmnxOamPmCfgLossSlmTable last changed. If tmnxOamPmCfgLossSlmTable has not changed since system startup, zero is returned.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxOamPmCfgMeasIntvlTableLstChg 1.3.6.1.4.1.6527.3.1.2.92.1.2.7
The value of tmnxOamPmCfgMeasIntvlTableLstChg indicates the time, since system startup, when tmnxOamPmCfgMeasIntvlTable last changed. If tmnxOamPmCfgMeasIntvlTable has not changed since system startup, zero is returned.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxOamPmCfgSessIpTableLastChg 1.3.6.1.4.1.6527.3.1.2.92.1.2.8
The value of tmnxOamPmCfgSessIpTableLastChg indicates the time, since system startup, when tmnxOamPmCfgSessIpTable last changed. If tmnxOamPmCfgSessIpTable has not changed since system startup, zero is returned.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxOamPmCfgTwampLtTableLastChg 1.3.6.1.4.1.6527.3.1.2.92.1.2.9
The value of tmnxOamPmCfgTwampLtTableLastChg indicates the time, since system startup, when tmnxOamPmCfgTwampLtTable last changed. If tmnxOamPmCfgTwampLtTable has not changed since system startup, zero is returned.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxOamPmCfgTwlRflTableLastChg 1.3.6.1.4.1.6527.3.1.2.92.1.2.10
The value of tmnxOamPmCfgTwlRflTableLastChg indicates the time, since system startup, when tmnxOamPmCfgTwlRflTable last changed. If tmnxOamPmCfgTwlRflTable has not changed since system startup, zero is returned.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxOamPmCfgTwlRflPfxTableLstChg 1.3.6.1.4.1.6527.3.1.2.92.1.2.11
The value of tmnxOamPmCfgTwlRflPfxTableLstChg indicates the time, since system startup, when tmnxOamPmCfgTwlRflPfxTable last changed. If tmnxOamPmCfgTwlRflPfxTable has not changed since system startup, zero is returned.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxOamPmCfgLossLmmTableLastChg 1.3.6.1.4.1.6527.3.1.2.92.1.2.12
The value of tmnxOamPmCfgLossLmmTableLastChg indicates the time, since system startup, when tmnxOamPmCfgLossLmmTable last changed. If tmnxOamPmCfgLossLmmTable has not changed since system startup, zero is returned.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxOamPmCfgThrLossFwBwTableLChg 1.3.6.1.4.1.6527.3.1.2.92.1.2.13
The value of tmnxOamPmCfgThrLossFwBwTableLChg indicates the time, since system startup, when tmnxOamPmCfgThrLossFwBwTable last changed. If tmnxOamPmCfgThrLossFwBwTable has not changed since system startup, zero is returned.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxOamPmCfgThrLossFwBwAgTableLC 1.3.6.1.4.1.6527.3.1.2.92.1.2.14
The value of tmnxOamPmCfgThrLossFwBwAgTableLC indicates the time, since system startup, when tmnxOamPmCfgThrLossFwBwAgTable last changed. If tmnxOamPmCfgThrLossFwBwAgTable has not changed since system startup, zero is returned.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxOamPmCfgThrDelayTableLastChg 1.3.6.1.4.1.6527.3.1.2.92.1.2.15
The value of tmnxOamPmCfgThrDelayTableLastChg indicates the time, since system startup, when tmnxOamPmCfgThrDelayTable last changed. If tmnxOamPmCfgThrDelayTable has not changed since system startup, zero is returned.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxOamPmCfgBinGrpTypeDirTableLC 1.3.6.1.4.1.6527.3.1.2.92.1.2.16
The value of tmnxOamPmCfgBinGrpTypeDirTableLC indicates the time, since system startup, when tmnxOamPmCfgBinGrpTypeDirTable last changed. If tmnxOamPmCfgBinGrpTypeDirTable has not changed since system startup, zero is returned.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxOamPmCfgBinGroupTable 1.3.6.1.4.1.6527.3.1.2.92.1.3.1
tmnxOamPmCfgBinGroupTable contains the configuration information for OAM Performance Monitoring bin groups.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmCfgBinGroupEntry

tmnxOamPmCfgBinGroupEntry 1.3.6.1.4.1.6527.3.1.2.92.1.3.1.1
tmnxOamPmCfgBinGroupEntry contains the configuration information for one OAM Performance Monitoring bin group. Bin group 1 is created by the system on a CPM restart. The configuration of bin group 1 is shown in the following table. Object Value -------------------------------- ------------------------------ tmnxOamPmCfgBinGroupId 1 tmnxOamPmCfgBinGroupRowStatus active(1) tmnxOamPmCfgBinGroupAdminStatus enabled(1) tmnxOamPmCfgBinGroupDescription 'OAM PM default bin group (not modifiable)' tmnxOamPmCfgBinGroupFdBinCount 3 tmnxOamPmCfgBinGroupFdrBinCount 2 tmnxOamPmCfgBinGroupIfdvBinCount 2 Bin group 1 cannot be changed or destroyed. The rest of the rows in this table are created or destroyed using tmnxOamPmCfgBinGroupRowStatus. When a row is created, the following objects must be set in the SNMP Set PDU: tmnxOamPmCfgBinGroupRowStatus tmnxOamPmCfgBinGroupFdBinCount tmnxOamPmCfgBinGroupFdrBinCount tmnxOamPmCfgBinGroupIfdvBinCount The value of the following objects cannot be changed after their row is created: tmnxOamPmCfgBinGroupFdBinCount tmnxOamPmCfgBinGroupFdrBinCount tmnxOamPmCfgBinGroupIfdvBinCount A row can be destroyed if its administrative status (tmnxOamPmCfgBinGroupAdminStatus) is disabled, and no OAM Performance Monitoring sessions refer to the bin group.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmCfgBinGroupEntry  

tmnxOamPmCfgBinGroupId 1.3.6.1.4.1.6527.3.1.2.92.1.3.1.1.1
The value of tmnxOamPmCfgBinGroupId specifies the bin group to be configured or read.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmBinGroupId  

tmnxOamPmCfgBinGroupRowStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.1.1.2
The value of tmnxOamPmCfgBinGroupRowStatus specifies the status of the configuration row for the specified bin group.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxOamPmCfgBinGroupAdminStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.1.1.3
The value of tmnxOamPmCfgBinGroupAdminStatus specifies whether or not the specified bin group is administratively enabled. An attempt to set this object to 'disabled(2)' will be rejected if tests referring to the specified bin group are enabled. An attempt to set this object to 'enabled(1)' will be rejected if one (or more) of the three sets of lower bounds for the specified bin group (as configured using tmnxOamPmCfgBinLowerBound) is not in strictly ascending order. For example, tmnxOamPmCfgBinGroupAdminStatus.255 cannot be set to 'enabled(1)' if the following lower bound values are configured. Object ID Value (in microseconds) ------------------------------------- ----------------------- tmnxOamPmCfgBinLowerBound.255.fd(1).1 5000 tmnxOamPmCfgBinLowerBound.255.fd(1).2 5000 tmnxOamPmCfgBinLowerBound.255.fd(1).3 5002 Setting this object to 'disabled(2)' deletes ALL the OAM-PM statistics for each test belonging to each session which refers to the specified bin group. For example, if session 'Sess1' has a DMM test and an SLM test configured, and 'Sess1' uses bin-group 255, then disabling bin-group 255 will delete all the DMM and SLM statistics for 'Sess1'.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabled  

tmnxOamPmCfgBinGroupDescription 1.3.6.1.4.1.6527.3.1.2.92.1.3.1.1.4
The value of tmnxOamPmCfgBinGroupDescription specifies the descriptive text for the specified bin group.
Status: current Access: read-create
OBJECT-TYPE    
  TItemDescription  

tmnxOamPmCfgBinGroupFdBinCount 1.3.6.1.4.1.6527.3.1.2.92.1.3.1.1.5
The value of tmnxOamPmCfgBinGroupFdBinCount specifies the number of Frame Delay bins to be created for the specified bin group. There is no default value for this object. A value must be provided on row creation. See the DESCRIPTION clause for tmnxOamPmCfgBinGroupEntry for more information.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 2..10  

tmnxOamPmCfgBinGroupFdrBinCount 1.3.6.1.4.1.6527.3.1.2.92.1.3.1.1.6
The value of tmnxOamPmCfgBinGroupFdrBinCount specifies the number of Frame Delay Range bins to be created for the specified bin group. There is no default value for this object. A value must be provided on row creation. See the DESCRIPTION clause for tmnxOamPmCfgBinGroupEntry for more information.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 2..10  

tmnxOamPmCfgBinGroupIfdvBinCount 1.3.6.1.4.1.6527.3.1.2.92.1.3.1.1.7
The value of tmnxOamPmCfgBinGroupIfdvBinCount specifies the number of Inter-Frame Delay Variation bins to be created for the specified bin group. There is no default value for this object. A value must be provided on row creation. See the DESCRIPTION clause for tmnxOamPmCfgBinGroupEntry for more information.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 2..10  

tmnxOamPmCfgBinTable 1.3.6.1.4.1.6527.3.1.2.92.1.3.2
tmnxOamPmCfgBinTable contains the configuration information for OAM Performance Monitoring bins.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmCfgBinEntry

tmnxOamPmCfgBinEntry 1.3.6.1.4.1.6527.3.1.2.92.1.3.2.1
tmnxOamPmCfgBinEntry contains the configuration information for one OAM Performance Monitoring bin. Rows are created in this table when one (or more) of the following objects is set: tmnxOamPmCfgBinGroupFdBinCount, tmnxOamPmCfgBinGroupFdrBinCount, or tmnxOamPmCfgBinGroupIfdvBinCount. Suppose, for example, that the following values are set for bin group 255. Object Value ------------------------------------ ----- tmnxOamPmCfgBinGroupFdBinCount.255 4 tmnxOamPmCfgBinGroupFdrBinCount.255 3 tmnxOamPmCfgBinGroupIfdvBinCount.255 2 Then, the following rows will be created in this table (where index columns are underlined with '#', column names have been abbreviated by replacing 'tmnxOamPmCfg' with '_', and the _BinLowerBound column shows the default values). _BinGroupId _BinGroupType _BinId _BinLowerBound (microsec) ########### ############# ###### ------------------------- 255 fd(1) 1 5000 255 fd(1) 2 10000 255 fd(1) 3 15000 255 fdr(2) 1 5000 255 fdr(2) 2 10000 255 ifdv(3) 1 5000 Note that tmnxOamPmCfgBinGroupFdBinCount.255 is 4, but there are only three corresponding rows in this table. The fourth bin is bin 0, which has a hard coded lower bound of 0 microseconds. Bin 0 never has a row in this table. The lower bounds for a particular {tmnxOamPmCfgBinGroupId, tmnxOamPmCfgBinType} pair must be strictly ascending. See the tmnxOamPmCfgBinGroupAdminStatus DESCRIPTION clause for more information.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmCfgBinEntry  

tmnxOamPmCfgBinType 1.3.6.1.4.1.6527.3.1.2.92.1.3.2.1.1
The value of tmnxOamPmCfgBinType specifies the type of the bin to be configured or read.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmBinType  

tmnxOamPmCfgBinNum 1.3.6.1.4.1.6527.3.1.2.92.1.3.2.1.2
The value of tmnxOamPmCfgBinNum specifies the number of the bin to be configured or read.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmCfgBinNum  

tmnxOamPmCfgBinLowerBound 1.3.6.1.4.1.6527.3.1.2.92.1.3.2.1.3
The value of tmnxOamPmCfgBinLowerBound specifies the lower bound (in microseconds) for the specified bin. A lower bound can be changed if the administrative state (i.e. tmnxOamPmCfgBinGroupAdminStatus) for the parent bin group is disabled. Please see additional restrictions on setting lower bounds in the tmnxOamPmCfgBinEntry DESCRIPTION clause. The default lower bound for bin number 1 is 5000 microseconds. The default lower bound for a subsequent bin number is computed using defLowerBound(n) = defLowerBound(n-1) + (5000 microseconds).
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..4294967295  

tmnxOamPmCfgSessTable 1.3.6.1.4.1.6527.3.1.2.92.1.3.3
tmnxOamPmCfgSessTable contains the configuration information for OAM Performance Monitoring sessions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmCfgSessEntry

tmnxOamPmCfgSessEntry 1.3.6.1.4.1.6527.3.1.2.92.1.3.3.1
tmnxOamPmCfgSessEntry contains the configuration information for one OAM Performance Monitoring session. Rows are created or destroyed by SNMP Set operations on tmnxOamPmCfgSessRowStatus. An attempt to change the tmnxOamPmCfgSessBinGroupId value in a row (or an attempt to destroy the row) for a particular session will be rejected if an administratively enabled test (e.g. an SLM test) exists for the session.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmCfgSessEntry  

tmnxOamPmCfgSessName 1.3.6.1.4.1.6527.3.1.2.92.1.3.3.1.1
The value of tmnxOamPmCfgSessName specifies the name of the session to be configured or read.
Status: current Access: not-accessible
OBJECT-TYPE    
  TNamedItem  

tmnxOamPmCfgSessRowStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.3.1.2
The value of tmnxOamPmCfgSessRowStatus specifies the status of the configuration row for the specified session.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxOamPmCfgSessTestFamily 1.3.6.1.4.1.6527.3.1.2.92.1.3.3.1.3
The value of tmnxOamPmCfgSessTestFamily specifies the type of service (e.g. 'ethernet(1)') to be tested by the specified session. When a session is created, tmnxOamPmCfgSessRowStatus and tmnxOamPmCfgSessTestFamily must be specified in the same SNMP Set PDU. After a session is created, tmnxOamPmCfgSessTestFamily cannot be changed.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxOamPmTestFamily  

tmnxOamPmCfgSessType 1.3.6.1.4.1.6527.3.1.2.92.1.3.3.1.4
The value of tmnxOamPmCfgSessType specifies the type (e.g. 'onDemand(2)') of the specified session. When a session is created, tmnxOamPmCfgSessRowStatus and tmnxOamPmCfgSessType can be specified in the same SNMP Set PDU. Or, tmnxOamPmCfgSessType can be left at its default value. After a session is created, tmnxOamPmCfgSessType cannot be changed.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxOamPmSessionType  

tmnxOamPmCfgSessBinGroupId 1.3.6.1.4.1.6527.3.1.2.92.1.3.3.1.5
The value of tmnxOamPmCfgSessBinGroupId specifies the bin group to be used by the specified session. Changing the bin group for a session deletes ALL the OAM-PM statistics for the session's tests.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxOamPmBinGroupId  

tmnxOamPmCfgSessDescription 1.3.6.1.4.1.6527.3.1.2.92.1.3.3.1.6
The value of tmnxOamPmCfgSessDescription specifies the descriptive text for the specified session.
Status: current Access: read-create
OBJECT-TYPE    
  TItemDescription  

tmnxOamPmCfgSessEthTable 1.3.6.1.4.1.6527.3.1.2.92.1.3.4
tmnxOamPmCfgSessEthTable contains the Ethernet endpoint configuration information for OAM Performance Monitoring sessions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmCfgSessEthEntry

tmnxOamPmCfgSessEthEntry 1.3.6.1.4.1.6527.3.1.2.92.1.3.4.1
tmnxOamPmCfgSessEthEntry contains the Ethernet endpoint configuration information for one OAM Performance Monitoring session. A row is created when a tmnxOamPmCfgSessTable row is created with tmnxOamPmCfgSessTestFamily = 'ethernet(1)'. A row is destroyed when a tmnxOamPmCfgSessTable row with tmnxOamPmCfgSessTestFamily = 'ethernet(1)' is destroyed. An attempt to change a value in a row for a particular session will be rejected if an administratively enabled test (e.g. an SLM test) exists for the session.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmCfgSessEthEntry  

tmnxOamPmCfgSessEthSrcMepId 1.3.6.1.4.1.6527.3.1.2.92.1.3.4.1.1
The value of tmnxOamPmCfgSessEthSrcMepId specifies the source Ethernet Maintenance association End Point (MEP) identifier to be used by the specified session. Zero indicates a value has not been configured.
Status: current Access: read-write
OBJECT-TYPE    
  Dot1agCfmMepIdOrZero  

tmnxOamPmCfgSessEthSrcMdIndex 1.3.6.1.4.1.6527.3.1.2.92.1.3.4.1.2
The value of tmnxOamPmCfgSessEthSrcMdIndex specifies the source Ethernet Maintenance Domain (MD) index to be used by the specified session. Zero indicates a value has not been configured.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmCfgSessEthSrcMaIndex 1.3.6.1.4.1.6527.3.1.2.92.1.3.4.1.3
The value of tmnxOamPmCfgSessEthSrcMaIndex specifies the source Ethernet Maintenance Association (MA) index to be used by the specified session. Zero indicates a value has not been configured.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmCfgSessEthPriority 1.3.6.1.4.1.6527.3.1.2.92.1.3.4.1.4
The value of tmnxOamPmCfgSessEthPriority specifies the value to be copied into the priority field when launching a test PDU for the specified session.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..7  

tmnxOamPmCfgSessEthDestMacAddr 1.3.6.1.4.1.6527.3.1.2.92.1.3.4.1.5
The value of tmnxOamPmCfgSessEthDestMacAddr specifies the destination MAC address for the specified session. The all-zeros MAC address indicates a value has not been configured.
Status: current Access: read-write
OBJECT-TYPE    
  MacAddress  

tmnxOamPmCfgDelayDmmTable 1.3.6.1.4.1.6527.3.1.2.92.1.3.5
tmnxOamPmCfgDelayDmmTable contains the configuration information for OAM Performance Monitoring Delay Measurement Message (DMM) tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmCfgDelayDmmEntry

tmnxOamPmCfgDelayDmmEntry 1.3.6.1.4.1.6527.3.1.2.92.1.3.5.1
tmnxOamPmCfgDelayDmmEntry contains the configuration information for one OAM Performance Monitoring Delay Measurement Message (DMM) test. Rows are created or destroyed by SNMP Set operations on tmnxOamPmCfgDelayDmmRowStatus. An attempt to change any value in a row (except tmnxOamPmCfgDelayDmmAdminStatus and tmnxOamPmCfgDelayDmmOnDmndStatus) will be rejected if tmnxOamPmCfgDelayDmmAdminStatus is 'enabled(1)'.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmCfgDelayDmmEntry  

tmnxOamPmCfgDelayDmmRowStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.5.1.1
The value of tmnxOamPmCfgDelayDmmRowStatus specifies the status of the configuration row for the specified session's DMM test. An attempt to create a row for a session with tmnxOamPmCfgSessTestFamily other than 'ethernet(1)' will be rejected.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxOamPmCfgDelayDmmAdminStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.5.1.2
The value of tmnxOamPmCfgDelayDmmAdminStatus specifies whether or not the specified session's DMM test is administratively enabled. If the session type (tmnxOamPmCfgSessType) is 'proactive(1)', setting tmnxOamPmCfgDelayDmmAdminStatus to 'enabled(1)'/'disabled(2)' starts/stops the test. If the session type is 'onDemand(2)', see the DESCRIPTION clause for tmnxOamPmCfgDelayDmmOnDmndStatus for information on starting/stopping the test. An attempt to set this object to 'enabled(1)' will be rejected if the tmnxOamPmCfgSessEthTable row for the specified session has incomplete endpoint information for the test (e.g. if tmnxOamPmCfgSessEthDestMacAddr is the all-zeroes MAC address).
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabled  

tmnxOamPmCfgDelayDmmOnDmndStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.5.1.3
The value of tmnxOamPmCfgDelayDmmOnDmndStatus specifies the status of the on-demand DMM test for the specified session. Values: 'enabled(1)' Set by an SNMP manager to start an on-demand DMM test. The test will start if tmnxOamPmCfgDelayDmmAdminStatus is 'enabled(1)'. 'disabled(2)' Set by an SNMP manager to stop an on-demand DMM test. Set by SROS to indicate an on-demand DMM test has stopped running because the configured period for the test (i.e. tmnxOamPmCfgDelayDmmTestDuration) has ended. Set by SROS for an on-demand DMM test when tmnxOamPmCfgDelayDmmAdminStatus is set to 'disabled(2)'. 'notApplicable(3)' This code point is the only acceptable value for a proactive DMM test. An attempt to set this code point for an on-demand DMM test will be rejected. The default value is 'disabled(2)' for an on-demand DMM test, and 'notApplicable(3)' for a proactive DMM test.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabledOrNA  

tmnxOamPmCfgDelayDmmTestId 1.3.6.1.4.1.6527.3.1.2.92.1.3.5.1.4
The value of tmnxOamPmCfgDelayDmmTestId specifies the test identifier for the specified session's DMM test. When a DMM test is created, tmnxOamPmCfgDelayDmmRowStatus and tmnxOamPmCfgDelayDmmTestId must be specified in the same SNMP Set PDU. When a Y.1731 DMM PDU is being built, the test identifier is copied into the PDU's Test ID TLV. An attempt to add a duplicate test identifier to this table will be rejected. Test identifier values larger than 2147483647 are reserved for internal use.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..2147483647  

tmnxOamPmCfgDelayDmmInterval 1.3.6.1.4.1.6527.3.1.2.92.1.3.5.1.5
The value of tmnxOamPmCfgDelayDmmInterval specifies the elapsed time between transmission of Y.1731 DMM PDUs for the specified session's DMM test.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 100 | 1000 | 10000  

tmnxOamPmCfgDelayDmmDataTlvSize 1.3.6.1.4.1.6527.3.1.2.92.1.3.5.1.6
The value of tmnxOamPmCfgDelayDmmDataTlvSize specifies the amount of padding to be added to each launched Y.1731 DMM PDU for the specified session's DMM test. Zero specifies that a Data TLV should not be added to each launched Y.1731 DMM PDU. A value larger than zero specifies the total size (including the header) of the Data TLV added to each launched Y.1731 DMM PDU.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0 | 3..2000  

tmnxOamPmCfgDelayDmmTestDuration 1.3.6.1.4.1.6527.3.1.2.92.1.3.5.1.7
The value of tmnxOamPmCfgDelayDmmTestDuration specifies the test duration for the specified session's DMM test. Zero specifies a test which runs until it is manually stopped. An attempt to set a non-zero value will be rejected if tmnxOamPmCfgSessType is 'proactive(1)'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..86400  

tmnxOamPmCfgDelayDmmRunTimeLeft 1.3.6.1.4.1.6527.3.1.2.92.1.3.5.1.8
The value of tmnxOamPmCfgDelayDmmRunTimeLeft indicates the run time remaining for the specified session's DMM test. For example, suppose a DMM test has the following configuration: tmnxOamPmCfgSessType tmnxOamPmCfgDelayDmmTestDuration -------------------- -------------------------------- 'onDemand(2)' 1000 (seconds) Then, when the DMM test is started (see tmnxOamPmCfgDelayDmmOnDmndStatus), tmnxOamPmCfgDelayDmmRunTimeLeft is initialized to 1000 seconds. After a minute, tmnxOamPmCfgDelayDmmRunTimeLeft is 940 seconds. If tmnxOamPmCfgSessType is 'proactive(1)', zero is always returned (because a proactive test runs until it is manually stopped). If tmnxOamPmCfgSessType is 'onDemand(2)' and the test is stopped (see tmnxOamPmCfgDelayDmmOnDmndStatus), zero is returned (because the test is not running).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..86400  

tmnxOamPmCfgLossSlmTable 1.3.6.1.4.1.6527.3.1.2.92.1.3.6
tmnxOamPmCfgLossSlmTable contains the configuration information for OAM Performance Monitoring Synthetic Loss Message (SLM) tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmCfgLossSlmEntry

tmnxOamPmCfgLossSlmEntry 1.3.6.1.4.1.6527.3.1.2.92.1.3.6.1
tmnxOamPmCfgLossSlmEntry contains the configuration information for one OAM Performance Monitoring Synthetic Loss Message (SLM) test. Rows are created or destroyed by SNMP Set operations on tmnxOamPmCfgLossSlmRowStatus. An attempt to change any value in a row (except tmnxOamPmCfgLossSlmAdminStatus and tmnxOamPmCfgLossSlmOnDmndStatus) will be rejected if tmnxOamPmCfgLossSlmAdminStatus is 'enabled(1)'. The following objects must all be set together in one SNMP Set PDU: tmnxOamPmCfgLossSlmChliThreshold, tmnxOamPmCfgLossSlmConsecDeltaTs, tmnxOamPmCfgLossSlmInterval, and tmnxOamPmCfgLossSlmTxFrmsPerDelT.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmCfgLossSlmEntry  

tmnxOamPmCfgLossSlmRowStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.6.1.1
The value of tmnxOamPmCfgLossSlmRowStatus specifies the status of the configuration row for the specified session's SLM test. An attempt to create a row for a session with tmnxOamPmCfgSessTestFamily other than 'ethernet(1)' will be rejected.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxOamPmCfgLossSlmAdminStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.6.1.2
The value of tmnxOamPmCfgLossSlmAdminStatus specifies whether or not the specified session's SLM test is administratively enabled. If the session type (tmnxOamPmCfgSessType) is 'proactive(1)', setting tmnxOamPmCfgLossSlmAdminStatus to 'enabled(1)'/'disabled(2)' starts/stops the test. If the session type is 'onDemand(2)', see the DESCRIPTION clause for tmnxOamPmCfgLossSlmOnDmndStatus for information on starting/stopping the test. An attempt to set this object to 'enabled(1)' will be rejected if the tmnxOamPmCfgSessEthTable row for the specified session has incomplete endpoint information for the test (e.g. if tmnxOamPmCfgSessEthDestMacAddr is the all-zeroes MAC address).
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabled  

tmnxOamPmCfgLossSlmOnDmndStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.6.1.3
The value of tmnxOamPmCfgLossSlmOnDmndStatus specifies the status of the on-demand SLM test for the specified session. Values: 'enabled(1)' Set by an SNMP manager to start an on-demand SLM test. The test will start if tmnxOamPmCfgLossSlmAdminStatus is 'enabled(1)'. 'disabled(2)' Set by an SNMP manager to stop an on-demand SLM test. Set by SROS to indicate an on-demand SLM test has stopped running because the configured period for the test (i.e. tmnxOamPmCfgLossSlmTestDuration) has ended. Set by SROS for an on-demand SLM test when tmnxOamPmCfgLossSlmAdminStatus is set to 'disabled(2)'. 'notApplicable(3)' This code point is the only acceptable value for a proactive SLM test. An attempt to set this code point for an on-demand SLM test will be rejected. The default value is 'disabled(2)' for an on-demand SLM test, and 'notApplicable(3)' for a proactive SLM test.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabledOrNA  

tmnxOamPmCfgLossSlmTestId 1.3.6.1.4.1.6527.3.1.2.92.1.3.6.1.4
The value of tmnxOamPmCfgLossSlmTestId specifies the test identifier for the specified session's SLM test. When an SLM test is created, tmnxOamPmCfgLossSlmRowStatus and tmnxOamPmCfgLossSlmTestId must be specified in the same SNMP Set PDU. When a Y.1731 SLM PDU is being built, the test identifier is copied into the PDU's Test ID field. An attempt to add a duplicate test identifier to this table will be rejected. Test identifier values larger than 2147483647 are reserved for internal use.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..2147483647  

tmnxOamPmCfgLossSlmInterval 1.3.6.1.4.1.6527.3.1.2.92.1.3.6.1.5
The value of tmnxOamPmCfgLossSlmInterval specifies the elapsed time between transmission of Y.1731 SLM PDUs for the specified session's SLM test.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 100 | 1000  

tmnxOamPmCfgLossSlmDataTlvSize 1.3.6.1.4.1.6527.3.1.2.92.1.3.6.1.6
The value of tmnxOamPmCfgLossSlmDataTlvSize specifies the amount of padding to be added to each launched Y.1731 SLM PDU for the specified session's SLM test. Zero specifies that a Data TLV should not be added to each launched Y.1731 SLM PDU. A value larger than zero specifies the total size (including the header) of the Data TLV added to each launched Y.1731 SLM PDU.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0 | 3..2000  

tmnxOamPmCfgLossSlmTxFrmsPerDelT 1.3.6.1.4.1.6527.3.1.2.92.1.3.6.1.7
The value of tmnxOamPmCfgLossSlmTxFrmsPerDelT specifies the number of Y.1731 SLM frames to send in one MEF-35 'delta_t' (also known as 'Small Time Interval') for the specified session's SLM test. Expressed in milliseconds, delta_t = tmnxOamPmCfgLossSlmTxFrmsPerDelT * tmnxOamPmCfgLossSlmInterval.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..50  

tmnxOamPmCfgLossSlmConsecDeltaTs 1.3.6.1.4.1.6527.3.1.2.92.1.3.6.1.8
The value of tmnxOamPmCfgLossSlmConsecDeltaTs specifies the number of consecutive MEF-35 'delta_t's (also known as 'Small Time Intervals') which constitute a MEF-35 'Availability Window' for the specified session's SLM test. The duration of an Availability Window (in milliseconds) is tmnxOamPmCfgLossSlmTxFrmsPerDelT * tmnxOamPmCfgLossSlmInterval * tmnxOamPmCfgLossSlmConsecDeltaTs. An attempt to change the duration of an Availability Window to more than 10,000 milliseconds will be rejected. An attempt to change tmnxOamPmCfgLossSlmConsecDeltaTs to a value less than or equal to tmnxOamPmCfgLossSlmChliThreshold will be rejected.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 2..10  

tmnxOamPmCfgLossSlmChliThreshold 1.3.6.1.4.1.6527.3.1.2.92.1.3.6.1.9
The value of tmnxOamPmCfgLossSlmChliThreshold specifies the MEF-35 Consecutive High Loss Interval (CHLI) threshold for the specified session's SLM test. An attempt to change tmnxOamPmCfgLossSlmChliThreshold to a value greater than or equal to tmnxOamPmCfgLossSlmConsecDeltaTs will be rejected.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..9  

tmnxOamPmCfgLossSlmFlrThreshold 1.3.6.1.4.1.6527.3.1.2.92.1.3.6.1.10
The value of tmnxOamPmCfgLossSlmFlrThreshold specifies the MEF-35 Frame Loss Ratio (FLR) threshold for the specified session's SLM test. The FLR threshold is used to decide if a MEF-35 Small Time Interval (also known as delta_t) is Available or Unavailable.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..100  

tmnxOamPmCfgLossSlmTestDuration 1.3.6.1.4.1.6527.3.1.2.92.1.3.6.1.11
The value of tmnxOamPmCfgLossSlmTestDuration specifies the test duration for the specified session's SLM test. Zero specifies a test which runs until it is manually stopped. An attempt to set a non-zero value will be rejected if tmnxOamPmCfgSessType is 'proactive(1)'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..86400  

tmnxOamPmCfgLossSlmRunTimeLeft 1.3.6.1.4.1.6527.3.1.2.92.1.3.6.1.12
The value of tmnxOamPmCfgLossSlmRunTimeLeft indicates the run time remaining for the specified session's SLM test. For example, suppose an SLM test has the following configuration: tmnxOamPmCfgSessType tmnxOamPmCfgLossSlmTestDuration -------------------- -------------------------------- 'onDemand(2)' 1000 (seconds) Then, when the SLM test is started (see tmnxOamPmCfgLossSlmOnDmndStatus), tmnxOamPmCfgLossSlmRunTimeLeft is initialized to 1000 seconds. After a minute, tmnxOamPmCfgLossSlmRunTimeLeft is 940 seconds. If tmnxOamPmCfgSessType is 'proactive(1)', zero is always returned (because a proactive test runs until it is manually stopped). If tmnxOamPmCfgSessType is 'onDemand(2)' and the test is stopped (see tmnxOamPmCfgLossSlmOnDmndStatus), zero is returned (because the test is not running).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..86400  

tmnxOamPmCfgMeasIntvlTable 1.3.6.1.4.1.6527.3.1.2.92.1.3.7
tmnxOamPmCfgMeasIntvlTable contains the configuration information for OAM Performance Monitoring measurement intervals.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmCfgMeasIntvlEntry

tmnxOamPmCfgMeasIntvlEntry 1.3.6.1.4.1.6527.3.1.2.92.1.3.7.1
tmnxOamPmCfgMeasIntvlEntry contains the configuration information for the OAM Performance Monitoring measurement interval associated with the specified session and measurement interval duration. Rows are created or destroyed by SNMP Set operations on tmnxOamPmCfgMeasIntvlRowStatus.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmCfgMeasIntvlEntry  

tmnxOamPmCfgMeasIntvlDuration 1.3.6.1.4.1.6527.3.1.2.92.1.3.7.1.1
The value of tmnxOamPmCfgMeasIntvlDuration specifies the duration of the measurement interval (e.g. 'mi15Minutes(2)') to be read or configured.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmCfgMeasIntervalDuration  

tmnxOamPmCfgMeasIntvlRowStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.7.1.2
The value of tmnxOamPmCfgMeasIntvlRowStatus specifies the status of the configuration row for the specified session and measurement interval duration.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxOamPmCfgMeasIntvlAccntPolicy 1.3.6.1.4.1.6527.3.1.2.92.1.3.7.1.3
The value of tmnxOamPmCfgMeasIntvlAccntPolicy specifies the accounting policy for the specified session and measurement interval duration. Zero specifies that the specified session and measurement interval duration has no associated accounting policy.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0 | 1..99  

tmnxOamPmCfgMeasIntvlsStored 1.3.6.1.4.1.6527.3.1.2.92.1.3.7.1.4
The value of tmnxOamPmCfgMeasIntvlsStored specifies the maximum number of historical measurement intervals which can be read using SNMP Get operations. For example, suppose tmnxOamPmCfgMeasIntvlsStored is 32 in the row indexed by {'mySess1', 'mi15Minutes(2)'}. Suppose 'mySess1' has a DMM test which has been running for at least 8 hours (i.e. 15 minutes/interval * 32 intervals). Then, the number of SNMP accessible 15 minute intervals for the test is shown in the following table. Test State Number of SNMP Accessible 15 Minute Intervals ---------- ----------------------------------------------------------- running 33 (i.e. 32 historical intervals, and the current interval) stopped 32 (i.e. 32 historical intervals) At the moment when a test is stopped, the current interval becomes the newest historical interval. If that makes the total number of historical intervals larger than tmnxOamPmCfgMeasIntvlsStored, the oldest historical interval is made SNMP inaccessible. In a typical configuration, older statistics are recorded in a local file (see tmnxOamPmCfgMeasIntvlAccntPolicy). Statistics in the file are not SNMP accessible. The range and default of tmnxOamPmCfgMeasIntvlsStored varies with the row's measurement interval duration index value, as follows. tmnxOamPmCfgMeasIntvlDuration Intvls Stored Range Intvls Stored Default ----------------------------- ------------------- --------------------- 'mi5Minutes(5)' 1..96 32 'mi15Minutes(2)' 1..96 32 'mi1Hour(3)' 1..24 8 'mi1Day(4)' 1..1 1 The following limit is enforced per session (where 'S' is the session name): tmnxOamPmCfgMeasIntvlsStored.S.mi5Minutes(5) + tmnxOamPmCfgMeasIntvlsStored.S.mi15Minutes(2) <= 96.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..96  

tmnxOamPmCfgMeasIntvlBoundaryTyp 1.3.6.1.4.1.6527.3.1.2.92.1.3.7.1.5
The value of tmnxOamPmCfgMeasIntvlBoundaryTyp specifies whether or not the start of each measurement interval is aligned to the wall clock. Values: clockAligned(1) For example, if the specified tmnxOamPmCfgMeasIntvlDuration is 'mi1Day(4)', the first measurement interval for the test will start at midnight (UTC). See the DESCRIPTION clause for tmnxOamPmCfgMeasIntvlClockOffset for additional information. testRelative(2) The first measurement interval for the test will start when the test starts.
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER clockAligned(1), testRelative(2)  

tmnxOamPmCfgMeasIntvlClockOffset 1.3.6.1.4.1.6527.3.1.2.92.1.3.7.1.6
The value of tmnxOamPmCfgMeasIntvlClockOffset specifies the offset (in seconds) for the start of a measurement interval. For example, the following set of values will result in each one day measurement interval for the specified session starting 6 seconds after midnight (UTC). Object Value -------------------------------- ----------------- tmnxOamPmCfgMeasIntvlDuration 'mi1Day(4)' tmnxOamPmCfgMeasIntvlBoundaryTyp 'clockAligned(1)' tmnxOamPmCfgMeasIntvlClockOffset 6 This value must be less than tmnxOamPmCfgMeasIntvlDuration (expressed in seconds). For example, if tmnxOamPmCfgMeasIntvlDuration is 'mi15Minutes(2)' (i.e. 900 seconds), this value must be in the range 0..899. An attempt to set this object to a non-zero value when tmnxOamPmCfgMeasIntvlBoundaryTyp is 'testRelative(2)' will be rejected.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..86399  

tmnxOamPmCfgMeasIntvlDelayTCAs 1.3.6.1.4.1.6527.3.1.2.92.1.3.7.1.7
The value of tmnxOamPmCfgMeasIntvlDelayTCAs specifies the administrative state of delay Threshold Crossing Alerts (TCAs) for this measurement interval. Delay TCAs are administratively enabled if both tmnxOamPmCfgMeasIntvlDelayTCAs and tmnxOamPmCfgMeasIntvlTCAs are 'enabled(1)'. Delay TCAs are configured using tmnxOamPmCfgThrDelayTable.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabled  

tmnxOamPmCfgMeasIntvlLossTCAs 1.3.6.1.4.1.6527.3.1.2.92.1.3.7.1.8
The value of tmnxOamPmCfgMeasIntvlLossTCAs specifies the administrative state of loss Threshold Crossing Alerts (TCAs) for this measurement interval. Loss TCAs are administratively enabled if both tmnxOamPmCfgMeasIntvlLossTCAs and tmnxOamPmCfgMeasIntvlTCAs are 'enabled(1)'. Loss TCAs are configured using tmnxOamPmCfgThrLossFwBwTable and tmnxOamPmCfgThrLossFwBwAgTable.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabled  

tmnxOamPmCfgMeasIntvlTCAs 1.3.6.1.4.1.6527.3.1.2.92.1.3.7.1.9
The value of tmnxOamPmCfgMeasIntvlTCAs specifies the administrative state of Threshold Crossing Alerts (TCAs) for this measurement interval. Delay TCAs are administratively enabled if both tmnxOamPmCfgMeasIntvlDelayTCAs and tmnxOamPmCfgMeasIntvlTCAs are 'enabled(1)'. Loss TCAs are administratively enabled if both tmnxOamPmCfgMeasIntvlLossTCAs and tmnxOamPmCfgMeasIntvlTCAs are 'enabled(1)'.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabled  

tmnxOamPmCfgSessIpTable 1.3.6.1.4.1.6527.3.1.2.92.1.3.8
tmnxOamPmCfgSessIpTable contains the IP endpoint configuration for the IP tests belonging to OAM Performance Monitoring sessions.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmCfgSessIpEntry

tmnxOamPmCfgSessIpEntry 1.3.6.1.4.1.6527.3.1.2.92.1.3.8.1
tmnxOamPmCfgSessIpEntry contains the IP endpoint configuration for the IP tests belonging to one OAM Performance Monitoring session. A row is created when a tmnxOamPmCfgSessTable row is created with tmnxOamPmCfgSessTestFamily = 'ip(2)'. A row is destroyed when a tmnxOamPmCfgSessTable row with tmnxOamPmCfgSessTestFamily = 'ip(2)' is destroyed. An attempt to change a value in a row for a particular session will be rejected if an administratively enabled test (e.g. a TWAMP-Light test) exists for the session.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmCfgSessIpEntry  

tmnxOamPmCfgSessIpServiceId 1.3.6.1.4.1.6527.3.1.2.92.1.3.8.1.1
The value of tmnxOamPmCfgSessIpServiceId specifies the virtual router to be used by IP tests belonging to the specified session. Zero specifies the Base virtual router, as defined in TIMETRA-VRTR-MIB::vRtrConfTable. A value larger than zero should be the service identifier of a VPRN service (as configured by setting TIMETRA-SERV-MIB::svcType to 'vprn(4)'). Otherwise, the session's test(s) will fail.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..2147483647  

tmnxOamPmCfgSessIpSrcAddressType 1.3.6.1.4.1.6527.3.1.2.92.1.3.8.1.2
The value of tmnxOamPmCfgSessIpSrcAddressType specifies the address type of tmnxOamPmCfgSessIpSrcAddress.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

tmnxOamPmCfgSessIpSrcAddress 1.3.6.1.4.1.6527.3.1.2.92.1.3.8.1.3
The value of tmnxOamPmCfgSessIpSrcAddress specifies the source IP address to be used by IP tests belonging to the specified session. tmnxOamPmCfgSessIpSrcAddressType and tmnxOamPmCfgSessIpSrcAddress must be set in one SNMP PDU.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress Size(0|4|16)  

tmnxOamPmCfgSessIpDstAddressType 1.3.6.1.4.1.6527.3.1.2.92.1.3.8.1.4
The value of tmnxOamPmCfgSessIpDstAddressType specifies the address type of tmnxOamPmCfgSessIpDstAddress.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

tmnxOamPmCfgSessIpDstAddress 1.3.6.1.4.1.6527.3.1.2.92.1.3.8.1.5
The value of tmnxOamPmCfgSessIpDstAddress specifies the destination IP address to be used by IP tests belonging to the specified session. tmnxOamPmCfgSessIpDstAddressType and tmnxOamPmCfgSessIpDstAddress must be set in one SNMP PDU.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress Size(0|4|16)  

tmnxOamPmCfgSessIpDstUdpPort 1.3.6.1.4.1.6527.3.1.2.92.1.3.8.1.6
The value of tmnxOamPmCfgSessIpDstUdpPort specifies the destination UDP port to be used by IP tests belonging to the specified session. Zero indicates that no destination UDP port has been configured.
Status: current Access: read-write
OBJECT-TYPE    
  InetPortNumber  

tmnxOamPmCfgSessIpBypassRouting 1.3.6.1.4.1.6527.3.1.2.92.1.3.8.1.7
The value of tmnxOamPmCfgSessIpBypassRouting specifies whether or not to send the ping request (for an IP test which belongs to the specified session) to a host on a directly attached network, bypassing the routing table. At most one of tmnxOamPmCfgSessIpBypassRouting, tmnxOamPmCfgSessIpEgressIfName, and tmnxOamPmCfgSessIpNhAddress can be set to a non-default value.
Status: current Access: read-write
OBJECT-TYPE    
  TruthValue  

tmnxOamPmCfgSessIpEgressIfName 1.3.6.1.4.1.6527.3.1.2.92.1.3.8.1.8
The value of tmnxOamPmCfgSessIpEgressIfName specifies the name of the interface to be used to transmit a ping request (for an IP test which belongs to the specified session). At most one of tmnxOamPmCfgSessIpBypassRouting, tmnxOamPmCfgSessIpEgressIfName, and tmnxOamPmCfgSessIpNhAddress can be set to a non-default value.
Status: current Access: read-write
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxOamPmCfgSessIpNhAddressType 1.3.6.1.4.1.6527.3.1.2.92.1.3.8.1.9
The value of tmnxOamPmCfgSessIpNhAddressType specifies the address type of tmnxOamPmCfgSessIpNhAddress.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddressType  

tmnxOamPmCfgSessIpNhAddress 1.3.6.1.4.1.6527.3.1.2.92.1.3.8.1.10
The value of tmnxOamPmCfgSessIpNhAddress specifies the next-hop IP address to be used by IP tests belonging to the specified session. tmnxOamPmCfgSessIpNhAddressType and tmnxOamPmCfgSessIpNhAddress must be set in one SNMP PDU. At most one of tmnxOamPmCfgSessIpBypassRouting, tmnxOamPmCfgSessIpEgressIfName, and tmnxOamPmCfgSessIpNhAddress can be set to a non-default value.
Status: current Access: read-write
OBJECT-TYPE    
  InetAddress Size(0|4|16)  

tmnxOamPmCfgSessIpForwardClass 1.3.6.1.4.1.6527.3.1.2.92.1.3.8.1.11
The value of tmnxOamPmCfgSessIpForwardClass specifies the forwarding class name to be used when launching a ping request for an IP test belonging to the specified session. The forwarding class name must be present in the index column of TIMETRA-QOS-MIB::tFCNameTable.
Status: current Access: read-write
OBJECT-TYPE    
  TFCName  

tmnxOamPmCfgSessIpProfile 1.3.6.1.4.1.6527.3.1.2.92.1.3.8.1.12
The value of tmnxOamPmCfgSessIpProfile specifies the profile to be used when launching a ping request for an IP test belonging to the specified session.
Status: current Access: read-write
OBJECT-TYPE    
  TProfile  

tmnxOamPmCfgSessIpTtl 1.3.6.1.4.1.6527.3.1.2.92.1.3.8.1.13
The value of tmnxOamPmCfgSessIpTtl specifies the time-to-live to be used when launching a ping request for an IP test belonging to the specified session.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 1..255  

tmnxOamPmCfgSessIpSrcUdpPort 1.3.6.1.4.1.6527.3.1.2.92.1.3.8.1.14
The value of tmnxOamPmCfgSessIpSrcUdpPort specifies the source UDP port to be used by IP tests belonging to the specified session. A source UDP port is allocated when the TWAMP-Light test for the specified session has its administrative status (i.e. tmnxOamPmCfgTwampLtAdminStatus) changed to 'enabled(1)'. The port is deallocated when the TWAMP-Light test has its administrative status changed to 'disabled(2)'. When allocating a source UDP port: 1. If tmnxOamPmCfgSessIpSrcUdpPort is zero, the source UDP port is allocated from the dynamic pool of UDP ports. 2. If tmnxOamPmCfgSessIpSrcUdpPort is non-zero, the source UDP port with port number equal to tmnxOamPmCfgSessIpSrcUdpPort is allocated. The read-only object tmnxOamPmStsSessIpSrcUdpPort indicates the allocated UDP port number.
Status: current Access: read-write
OBJECT-TYPE    
  InetPortNumber 0 | 64374..64383  

tmnxOamPmCfgTwampLtTable 1.3.6.1.4.1.6527.3.1.2.92.1.3.9
tmnxOamPmCfgTwampLtTable contains the configuration information for OAM Performance Monitoring TWAMP-Light (Two-Way Active Measurement Protocol, Light) tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmCfgTwampLtEntry

tmnxOamPmCfgTwampLtEntry 1.3.6.1.4.1.6527.3.1.2.92.1.3.9.1
tmnxOamPmCfgTwampLtEntry contains the configuration information for the OAM Performance Monitoring TWAMP-Light test for the specified session. Rows are created or destroyed by SNMP Set operations on tmnxOamPmCfgTwampLtRowStatus. An attempt to change any value in a row (except tmnxOamPmCfgTwampLtAdminStatus and tmnxOamPmCfgTwampLtOnDmndStatus) will be rejected if tmnxOamPmCfgTwampLtAdminStatus is 'enabled(1)'.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmCfgTwampLtEntry  

tmnxOamPmCfgTwampLtRowStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.9.1.1
The value of tmnxOamPmCfgTwampLtRowStatus specifies the status of the configuration row for the specified session's TWAMP-Light test. An attempt to create a row for a session with tmnxOamPmCfgSessTestFamily other than 'ip(2)' will be rejected.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxOamPmCfgTwampLtAdminStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.9.1.2
The value of tmnxOamPmCfgTwampLtAdminStatus specifies whether or not the specified session's TWAMP-Light test is administratively enabled. If the session type (tmnxOamPmCfgSessType) is 'proactive(1)', setting tmnxOamPmCfgTwampLtAdminStatus to 'enabled(1)'/'disabled(2)' starts/stops the test. If the session type is 'onDemand(2)', see the DESCRIPTION clause for tmnxOamPmCfgTwampLtOnDmndStatus for information on starting/stopping the test. An attempt to set this object to 'enabled(1)' will be rejected if the tmnxOamPmCfgSessIpTable row for the specified session has incomplete information for the test (e.g. if tmnxOamPmCfgSessIpSrcAddressType is 'unknown(0)').
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabled  

tmnxOamPmCfgTwampLtOnDmndStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.9.1.3
The value of tmnxOamPmCfgTwampLtOnDmndStatus specifies the status of the on-demand TWAMP-Light test for the specified session. Values: 'enabled(1)' Set by an SNMP manager to start an on-demand TWAMP-Light test. The test will start if tmnxOamPmCfgTwampLtAdminStatus is 'enabled(1)'. 'disabled(2)' Set by an SNMP manager to stop an on-demand TWAMP-Light test. Set by SROS to indicate an on-demand TWAMP-Light test has stopped running because the configured period for the test (i.e. tmnxOamPmCfgTwampLtTestDuration) has ended. Set by SROS for an on-demand TWAMP-Light test when tmnxOamPmCfgTwampLtAdminStatus is set to 'disabled(2)'. 'notApplicable(3)' This code point is the only acceptable value for a proactive TWAMP-Light test. An attempt to set this code point for an on-demand TWAMP-Light test will be rejected. The default value is 'disabled(2)' for an on-demand TWAMP-Light test, and 'notApplicable(3)' for a proactive TWAMP-Light test.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabledOrNA  

tmnxOamPmCfgTwampLtTestId 1.3.6.1.4.1.6527.3.1.2.92.1.3.9.1.4
The value of tmnxOamPmCfgTwampLtTestId specifies the test identifier for the specified session's TWAMP-Light test. When a TWAMP-Light test is created, tmnxOamPmCfgTwampLtRowStatus and tmnxOamPmCfgTwampLtTestId must be specified in the same SNMP Set PDU. An attempt to add a duplicate test identifier to this table will be rejected. Test identifier values larger than 2147483647 are reserved for internal use.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..2147483647  

tmnxOamPmCfgTwampLtInterval 1.3.6.1.4.1.6527.3.1.2.92.1.3.9.1.5
The value of tmnxOamPmCfgTwampLtInterval specifies the elapsed time between transmission of TWAMP-Test PDUs for the specified session's TWAMP-Light test.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 100 | 1000 | 10000  

tmnxOamPmCfgTwampLtPadSize 1.3.6.1.4.1.6527.3.1.2.92.1.3.9.1.6
The value of tmnxOamPmCfgTwampLtPadSize specifies the amount of padding to be added to each launched TWAMP-Test PDU for the specified session's TWAMP-Light test.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..2000  

tmnxOamPmCfgTwampLtTestDuration 1.3.6.1.4.1.6527.3.1.2.92.1.3.9.1.7
The value of tmnxOamPmCfgTwampLtTestDuration specifies the test duration for the specified session's TWAMP-Light test. Zero specifies a test which runs until it is manually stopped. An attempt to set a non-zero value will be rejected if tmnxOamPmCfgSessType is 'proactive(1)'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..86400  

tmnxOamPmCfgTwampLtRunTimeLeft 1.3.6.1.4.1.6527.3.1.2.92.1.3.9.1.8
The value of tmnxOamPmCfgTwampLtRunTimeLeft indicates the run time remaining for the specified session's TWAMP-Light test. For example, suppose a TWAMP-Light test has the following configuration: tmnxOamPmCfgSessType tmnxOamPmCfgTwampLtTestDuration -------------------- ------------------------------- 'onDemand(2)' 1000 (seconds) Then, when the TWAMP-Light test is started (see tmnxOamPmCfgTwampLtOnDmndStatus), tmnxOamPmCfgTwampLtRunTimeLeft is initialized to 1000 seconds. After a minute, tmnxOamPmCfgTwampLtRunTimeLeft is 940 seconds. If tmnxOamPmCfgSessType is 'proactive(1)', zero is always returned (because a proactive test runs until it is manually stopped). If tmnxOamPmCfgSessType is 'onDemand(2)' and the test is stopped (see tmnxOamPmCfgTwampLtOnDmndStatus), zero is returned (because the test is not running).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..86400  

tmnxOamPmCfgTwampLtCollectStats 1.3.6.1.4.1.6527.3.1.2.92.1.3.9.1.9
The value of tmnxOamPmCfgTwampLtCollectStats specifies the type(s) of statistics to collect while the TWAMP-Light test is running. Code points: collectDelayStats(1) - collect TWAMP-Light delay statistics (readable using tmnxOamPmStsDelayTwlTable and tmnxOamPmStsDelayTwlBinTable) collectLossStats(2) - collect TWAMP-Light loss statistics (readable using tmnxOamPmStsLossTwlTable) collectDelayAndLossStats(3) - collectDelayStats(1) and collectLossStats(2), simultaneously
Status: current Access: read-create
OBJECT-TYPE    
  INTEGER collectDelayStats(1), collectLossStats(2), collectDelayAndLossStats(3)  

tmnxOamPmCfgTwampLtTxFrmsPerDelT 1.3.6.1.4.1.6527.3.1.2.92.1.3.9.1.10
The value of tmnxOamPmCfgTwampLtTxFrmsPerDelT specifies the number of TWAMP-Light frames to send in one MEF-35 'delta_t' (also known as 'Small Time Interval') when computing loss statistics for the specified session's TWAMP-Light test. The loss parameters used by SROS for TWAMP-Light tests (e.g. tmnxOamPmCfgTwampLtTxFrmsPerDelT) are modelled after the MEF-35 loss parameters defined for Synthetic Loss Measurement (SLM) tests. Hence, the REFERENCE text for this object is a MEF-35 SLM section. Expressed in milliseconds, delta_t = tmnxOamPmCfgTwampLtTxFrmsPerDelT * tmnxOamPmCfgTwampLtInterval.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..50  

tmnxOamPmCfgTwampLtConsecDeltaTs 1.3.6.1.4.1.6527.3.1.2.92.1.3.9.1.11
The value of tmnxOamPmCfgTwampLtConsecDeltaTs specifies the number of consecutive MEF-35 'delta_t's (also known as 'Small Time Intervals') which constitute a MEF-35 'Availability Window' when computing loss statistics for the specified session's TWAMP-Light test. The loss parameters used by SROS for TWAMP-Light tests (e.g. tmnxOamPmCfgTwampLtConsecDeltaTs) are modelled after the MEF-35 loss parameters defined for Synthetic Loss Measurement (SLM) tests. Hence, the REFERENCE text for this object is a MEF-35 SLM section. The duration of an Availability Window (in milliseconds) is tmnxOamPmCfgTwampLtTxFrmsPerDelT * tmnxOamPmCfgTwampLtInterval * tmnxOamPmCfgTwampLtConsecDeltaTs. An attempt to change the duration of an Availability Window to more than 100,000 milliseconds will be rejected. An attempt to change tmnxOamPmCfgTwampLtConsecDeltaTs to a value less than or equal to tmnxOamPmCfgTwampLtChliThreshold will be rejected.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 2..10  

tmnxOamPmCfgTwampLtChliThreshold 1.3.6.1.4.1.6527.3.1.2.92.1.3.9.1.12
The value of tmnxOamPmCfgTwampLtChliThreshold specifies the MEF-35 Consecutive High Loss Interval (CHLI) threshold for the specified session's TWAMP-Light test. The loss parameters used by SROS for TWAMP-Light tests (e.g. tmnxOamPmCfgTwampLtChliThreshold) are modelled after the MEF-35 loss parameters defined for Synthetic Loss Measurement (SLM) tests. Hence, the REFERENCE text for this object is a MEF-35 SLM section. An attempt to change tmnxOamPmCfgTwampLtChliThreshold to a value greater than or equal to tmnxOamPmCfgTwampLtConsecDeltaTs will be rejected.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..9  

tmnxOamPmCfgTwampLtFlrThreshold 1.3.6.1.4.1.6527.3.1.2.92.1.3.9.1.13
The value of tmnxOamPmCfgTwampLtFlrThreshold specifies the MEF-35 Frame Loss Ratio (FLR) threshold for the specified session's TWAMP-Light test. The FLR threshold is used to decide if a MEF-35 Small Time Interval (also known as delta_t) is Available or Unavailable. The loss parameters used by SROS for TWAMP-Light tests (e.g. tmnxOamPmCfgTwampLtFlrThreshold) are modelled after the MEF-35 loss parameters defined for Synthetic Loss Measurement (SLM) tests. Hence, the REFERENCE text for this object is a MEF-35 SLM section.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..100  

tmnxOamPmCfgTwlRflTable 1.3.6.1.4.1.6527.3.1.2.92.1.3.10
tmnxOamPmCfgTwlRflTable contains the configuration information for OAM Performance Monitoring TWAMP-Light (Two-Way Active Measurement Protocol, Light) reflectors. A TWAMP-Light reflector responds to TWAMP-Test frames.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmCfgTwlRflEntry

tmnxOamPmCfgTwlRflEntry 1.3.6.1.4.1.6527.3.1.2.92.1.3.10.1
tmnxOamPmCfgTwlRflEntry contains the configuration information for the OAM Performance Monitoring TWAMP-Light reflector for the virtual router specified by the given service identifier. Service identifier zero specifies the Base virtual router (i.e. the virtual router with TIMETRA-VRTR-MIB::vRtrName = 'Base'). A service identifier larger than zero must be the service identifier of a VPRN service (i.e. a service with TIMETRA-SERV-MIB::svcType = 'vprn(4)'). Rows are created or destroyed by SNMP Set operations on tmnxOamPmCfgTwlRflRowStatus. A row indexed by a VPRN service identifier is destroyed when the VPRN service is destroyed.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmCfgTwlRflEntry  

tmnxOamPmCfgTwlRflRowStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.10.1.1
The value of tmnxOamPmCfgTwlRflRowStatus specifies the status of the configuration row for the TWAMP-Light reflector for the virtual router specified by the given service identifier. When a reflector is created, tmnxOamPmCfgTwlRflRowStatus and tmnxOamPmCfgTwlRflListenUdpPort must be specified in the same SNMP Set PDU.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxOamPmCfgTwlRflAdminStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.10.1.2
The value of tmnxOamPmCfgTwlRflAdminStatus specifies whether or not the specified TWAMP-Light reflector is administratively enabled. tmnxOamPmCfgTwlRflListenUdpPort cannot be changed while tmnxOamPmCfgTwlRflAdminStatus is 'enabled(1)'.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabled  

tmnxOamPmCfgTwlRflDescription 1.3.6.1.4.1.6527.3.1.2.92.1.3.10.1.3
The value of tmnxOamPmCfgTwlRflDescription specifies the descriptive text for the specified TWAMP-Light reflector.
Status: current Access: read-create
OBJECT-TYPE    
  TItemDescription  

tmnxOamPmCfgTwlRflListenUdpPort 1.3.6.1.4.1.6527.3.1.2.92.1.3.10.1.4
The value of tmnxOamPmCfgTwlRflListenUdpPort specifies the UDP port on which the specified TWAMP-Light reflector listens for TWAMP PDUs. When a reflector is created, tmnxOamPmCfgTwlRflRowStatus and tmnxOamPmCfgTwlRflListenUdpPort must be specified in the same SNMP Set PDU. tmnxOamPmCfgTwlRflListenUdpPort cannot be changed while tmnxOamPmCfgTwlRflAdminStatus is 'enabled(1)'. The valid range is (64364..64373). For backwards compatibility reasons, the range has not been restricted in the MIB definition.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1024..65535  

tmnxOamPmCfgTwlRflPfxTable 1.3.6.1.4.1.6527.3.1.2.92.1.3.11
tmnxOamPmCfgTwlRflPfxTable contains the configuration information for OAM Performance Monitoring TWAMP-Light (Two-Way Active Measurement Protocol, Light) reflector prefixes. The set of prefixes configured for a TWAMP-Light reflector defines a set of valid source addresses for the reflector. When the reflector is validating an incoming TWAMP-Test PDU, the PDU is rejected (and counted) if its source address is invalid.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmCfgTwlRflPfxEntry

tmnxOamPmCfgTwlRflPfxEntry 1.3.6.1.4.1.6527.3.1.2.92.1.3.11.1
tmnxOamPmCfgTwlRflPfxEntry contains the configuration information for the OAM Performance Monitoring TWAMP-Light reflector prefix specified by the indices. Rows are created or destroyed by SNMP Set operations on tmnxOamPmCfgTwlRflPfxRowStatus. Rows are destroyed when the corresponding tmnxOamPmCfgTwlRflTable row is destroyed.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmCfgTwlRflPfxEntry  

tmnxOamPmCfgTwlRflPfxPrefixType 1.3.6.1.4.1.6527.3.1.2.92.1.3.11.1.1
The value of tmnxOamPmCfgTwlRflPfxPrefixType specifies the prefix type of tmnxOamPmCfgTwlRflPfxPrefix.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

tmnxOamPmCfgTwlRflPfxPrefix 1.3.6.1.4.1.6527.3.1.2.92.1.3.11.1.2
The value of tmnxOamPmCfgTwlRflPfxPrefix (in combination with tmnxOamPmCfgTwlRflPfxPrefixType and tmnxOamPmCfgTwlRflPfxPrefixLen) specifies a valid source prefix for the TWAMP-Light reflector specified by the given service identifier. A TWAMP-Test PDU with an invalid source address (i.e. a source address which matches none of the prefixes configured against the reflector) will be counted and dropped by the reflector. Therefore, if no prefixes are configured against a reflector, the reflector will drop and count all incoming PDUs. Configuring the prefix 0.0.0.0/0 instructs the reflector to accept the source address in each incoming IPv4 TWAMP-Test PDU. Configuring the prefix 0::0/0 instructs the reflector to accept the source address in each incoming IPv6 TWAMP-Test PDU.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress Size(4|16)  

tmnxOamPmCfgTwlRflPfxPrefixLen 1.3.6.1.4.1.6527.3.1.2.92.1.3.11.1.3
The value of tmnxOamPmCfgTwlRflPfxPrefixLen (in combination with tmnxOamPmCfgTwlRflPfxPrefixType and tmnxOamPmCfgTwlRflPfxPrefix) specifies a valid source prefix for the TWAMP-Light reflector specified by the given service identifier.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressPrefixLength 0..128  

tmnxOamPmCfgTwlRflPfxRowStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.11.1.4
The value of tmnxOamPmCfgTwlRflPfxRowStatus specifies the status of the configuration row for the specified TWAMP-Light reflector prefix. An attempt to create a row will be rejected if there is no row with the same svcId in tmnxOamPmCfgTwlRflTable.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxOamPmCfgTwlRflPfxDescription 1.3.6.1.4.1.6527.3.1.2.92.1.3.11.1.5
The value of tmnxOamPmCfgTwlRflPfxDescription specifies the descriptive text for the specified TWAMP-Light reflector prefix.
Status: current Access: read-create
OBJECT-TYPE    
  TItemDescription  

tmnxOamPmCfgLossLmmTable 1.3.6.1.4.1.6527.3.1.2.92.1.3.12
tmnxOamPmCfgLossLmmTable contains the configuration information for OAM Performance Monitoring Loss Measurement Message (LMM) tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmCfgLossLmmEntry

tmnxOamPmCfgLossLmmEntry 1.3.6.1.4.1.6527.3.1.2.92.1.3.12.1
tmnxOamPmCfgLossLmmEntry contains the configuration information for one OAM Performance Monitoring Loss Measurement Message (LMM) test. Rows are created or destroyed by SNMP Set operations on tmnxOamPmCfgLossLmmRowStatus. An attempt to change any value in a row (except tmnxOamPmCfgLossLmmAdminStatus and tmnxOamPmCfgLossLmmOnDmndStatus) will be rejected if tmnxOamPmCfgLossLmmAdminStatus is 'enabled(1)'. The following objects must all be set together in one SNMP Set PDU: tmnxOamPmCfgLossLmmChliThreshold, tmnxOamPmCfgLossLmmConsecDeltaTs, and tmnxOamPmCfgLossLmmTxFrmsPerDelT.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmCfgLossLmmEntry  

tmnxOamPmCfgLossLmmRowStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.12.1.1
The value of tmnxOamPmCfgLossLmmRowStatus specifies the status of the configuration row for the specified session's LMM test. An attempt to create a row for a session with tmnxOamPmCfgSessTestFamily other than 'ethernet(1)' will be rejected.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxOamPmCfgLossLmmAdminStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.12.1.2
The value of tmnxOamPmCfgLossLmmAdminStatus specifies whether or not the specified session's LMM test is administratively enabled. If the session type (tmnxOamPmCfgSessType) is 'proactive(1)', setting tmnxOamPmCfgLossLmmAdminStatus to 'enabled(1)'/'disabled(2)' starts/stops the test. If the session type is 'onDemand(2)', see the DESCRIPTION clause for tmnxOamPmCfgLossLmmOnDmndStatus for information on starting/stopping the test. An attempt to set this object to 'enabled(1)' will be rejected if the tmnxOamPmCfgSessEthTable row for the specified session has incomplete endpoint information for the test (e.g. if tmnxOamPmCfgSessEthDestMacAddr is the all-zeroes MAC address).
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabled  

tmnxOamPmCfgLossLmmOnDmndStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.12.1.3
The value of tmnxOamPmCfgLossLmmOnDmndStatus specifies the status of the on-demand LMM test for the specified session. Values: 'enabled(1)' Set by an SNMP manager to start an on-demand LMM test. The test will start if tmnxOamPmCfgLossLmmAdminStatus is 'enabled(1)'. 'disabled(2)' Set by an SNMP manager to stop an on-demand LMM test. Set by SROS to indicate an on-demand LMM test has stopped running because the configured period for the test (i.e. tmnxOamPmCfgLossLmmTestDuration) has ended. Set by SROS for an on-demand LMM test when tmnxOamPmCfgLossLmmAdminStatus is set to 'disabled(2)'. 'notApplicable(3)' This code point is the only acceptable value for a proactive LMM test. An attempt to set this code point for an on-demand LMM test will be rejected. The default value is 'disabled(2)' for an on-demand LMM test, and 'notApplicable(3)' for a proactive LMM test.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabledOrNA  

tmnxOamPmCfgLossLmmTestId 1.3.6.1.4.1.6527.3.1.2.92.1.3.12.1.4
The value of tmnxOamPmCfgLossLmmTestId specifies the test identifier for the specified session's LMM test. When an LMM test is created, tmnxOamPmCfgLossLmmRowStatus and tmnxOamPmCfgLossLmmTestId must be specified in the same SNMP Set PDU. An attempt to add a duplicate test identifier to this table will be rejected. Test identifier values larger than 2147483647 are reserved for internal use.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..2147483647  

tmnxOamPmCfgLossLmmInterval 1.3.6.1.4.1.6527.3.1.2.92.1.3.12.1.5
The value of tmnxOamPmCfgLossLmmInterval specifies the elapsed time between transmission of Y.1731 LMM PDUs for the specified session's LMM test.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 100 | 1000 | 10000  

tmnxOamPmCfgLossLmmTestDuration 1.3.6.1.4.1.6527.3.1.2.92.1.3.12.1.6
The value of tmnxOamPmCfgLossLmmTestDuration specifies the test duration for the specified session's LMM test. Zero specifies a test which runs until it is manually stopped. An attempt to set a non-zero value will be rejected if tmnxOamPmCfgSessType is 'proactive(1)'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..86400  

tmnxOamPmCfgLossLmmRunTimeLeft 1.3.6.1.4.1.6527.3.1.2.92.1.3.12.1.7
The value of tmnxOamPmCfgLossLmmRunTimeLeft indicates the run time remaining for the specified session's LMM test. For example, suppose an LMM test has the following configuration: tmnxOamPmCfgSessType tmnxOamPmCfgLossLmmTestDuration -------------------- -------------------------------- 'onDemand(2)' 1000 (seconds) Then, when the LMM test is started (see tmnxOamPmCfgLossLmmOnDmndStatus), tmnxOamPmCfgLossLmmRunTimeLeft is initialized to 1000 seconds. After a minute, tmnxOamPmCfgLossLmmRunTimeLeft is 940 seconds. If tmnxOamPmCfgSessType is 'proactive(1)', zero is always returned (because a proactive test runs until it is manually stopped). If tmnxOamPmCfgSessType is 'onDemand(2)' and the test is stopped (see tmnxOamPmCfgLossLmmOnDmndStatus), zero is returned (because the test is not running).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..86400  

tmnxOamPmCfgLossLmmTxFrmsPerDelT 1.3.6.1.4.1.6527.3.1.2.92.1.3.12.1.8
The value of tmnxOamPmCfgLossLmmTxFrmsPerDelT specifies the number of LMM frames to send in one MEF-35 'delta_t' (also known as 'Small Time Interval') when computing availability statistics for the specified session's LMM test. The availability parameters used by SROS for LMM tests (e.g. tmnxOamPmCfgLossLmmTxFrmsPerDelT) are modelled after the MEF-35 availability parameters defined for Synthetic Loss Measurement (SLM) tests. Hence, the REFERENCE text for this object is a MEF-35 SLM section. Expressed in milliseconds, delta_t = tmnxOamPmCfgLossLmmTxFrmsPerDelT * tmnxOamPmCfgLossLmmInterval.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..50  

tmnxOamPmCfgLossLmmConsecDeltaTs 1.3.6.1.4.1.6527.3.1.2.92.1.3.12.1.9
The value of tmnxOamPmCfgLossLmmConsecDeltaTs specifies the number of consecutive MEF-35 'delta_t's (also known as 'Small Time Intervals') which constitute a MEF-35 'Availability Window' when computing availability statistics for the specified session's LMM test. The availability parameters used by SROS for LMM tests (e.g. tmnxOamPmCfgLossLmmConsecDeltaTs) are modelled after the MEF-35 availability parameters defined for Synthetic Loss Measurement (SLM) tests. Hence, the REFERENCE text for this object is a MEF-35 SLM section. The duration of an Availability Window (in milliseconds) is tmnxOamPmCfgLossLmmTxFrmsPerDelT * tmnxOamPmCfgLossLmmInterval * tmnxOamPmCfgLossLmmConsecDeltaTs. An attempt to change the duration of an Availability Window to more than 100,000 milliseconds will be rejected. An attempt to change tmnxOamPmCfgLossLmmConsecDeltaTs to a value less than or equal to tmnxOamPmCfgLossLmmChliThreshold will be rejected.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 2..10  

tmnxOamPmCfgLossLmmChliThreshold 1.3.6.1.4.1.6527.3.1.2.92.1.3.12.1.10
The value of tmnxOamPmCfgLossLmmChliThreshold specifies the MEF-35 Consecutive High Loss Interval (CHLI) threshold for the specified session's LMM test. The availability parameters used by SROS for LMM tests (e.g. tmnxOamPmCfgLossLmmChliThreshold) are modelled after the MEF-35 availability parameters defined for Synthetic Loss Measurement (SLM) tests. Hence, the REFERENCE text for this object is a MEF-35 SLM section. An attempt to change tmnxOamPmCfgLossLmmChliThreshold to a value greater than or equal to tmnxOamPmCfgLossLmmConsecDeltaTs will be rejected.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..9  

tmnxOamPmCfgLossLmmFlrThreshold 1.3.6.1.4.1.6527.3.1.2.92.1.3.12.1.11
The value of tmnxOamPmCfgLossLmmFlrThreshold specifies the MEF-35 Frame Loss Ratio (FLR) threshold for the specified session's LMM test. The FLR threshold is used to decide if a MEF-35 'delta_t' (also known as 'Small Time Interval') is Available or Unavailable. The availability parameters used by SROS for LMM tests (e.g. tmnxOamPmCfgLossLmmFlrThreshold) are modelled after the MEF-35 availability parameters defined for Synthetic Loss Measurement (SLM) tests. Hence, the REFERENCE text for this object is a MEF-35 SLM section.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..100  

tmnxOamPmCfgLossLmmAvAdminStatus 1.3.6.1.4.1.6527.3.1.2.92.1.3.12.1.12
The value of tmnxOamPmCfgLossLmmAvAdminStatus specifies whether or not collection of availability statistics is enabled for the specified session's LMM test. When the value of tmnxOamPmCfgLossLmmAvAdminStatus is 'disabled(2)', the following configuration objects are ignored: tmnxOamPmCfgLossLmmChliThreshold, tmnxOamPmCfgLossLmmConsecDeltaTs, tmnxOamPmCfgLossLmmFlrThreshold, and tmnxOamPmCfgLossLmmTxFrmsPerDelT. When the value of tmnxOamPmCfgLossLmmAvAdminStatus is 'disabled(2)', the value of each of the following counters is always zero: tmnxOamPmStsLossLmmAvailIndBwd, tmnxOamPmStsLossLmmAvailIndFwd, tmnxOamPmStsLossLmmChliBwd, tmnxOamPmStsLossLmmChliFwd, tmnxOamPmStsLossLmmHliBwd, tmnxOamPmStsLossLmmHliFwd, tmnxOamPmStsLossLmmUnavlIndBwd, tmnxOamPmStsLossLmmUnavlIndFwd, tmnxOamPmStsLossLmmUndetDelTsBwd, tmnxOamPmStsLossLmmUndetDelTsFwd, tmnxOamPmStsLossLmmUndtAvlBwd, tmnxOamPmStsLossLmmUndtAvlFwd, tmnxOamPmStsLossLmmUndtUnavlBwd, and tmnxOamPmStsLossLmmUndtUnavlFwd. When the counters listed above are stuck at zero, the corresponding TCA raise thresholds (for the specified LMM test) are never met or exceeded. The corresponding TCA raise thresholds are configured using the following objects: tmnxOamPmCfgThrLossChliRaise, tmnxOamPmCfgThrLossHliRaise, tmnxOamPmCfgThrLossUnavlIndRaise, tmnxOamPmCfgThrLossUndtAvlRaise, or tmnxOamPmCfgThrLossUndtUnavlRais.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxEnabledDisabled  

tmnxOamPmCfgThrLossFwBwTable 1.3.6.1.4.1.6527.3.1.2.92.1.3.13
tmnxOamPmCfgThrLossFwBwTable contains configured thresholds for OAM Performance Monitoring loss TCAs. The subset of the loss thresholds that are only configurable in the forward and backward directions is configured using this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmCfgThrLossFwBwEntry

tmnxOamPmCfgThrLossFwBwEntry 1.3.6.1.4.1.6527.3.1.2.92.1.3.13.1
tmnxOamPmCfgThrLossFwBwEntry contains the configured thresholds for the forward or backward direction of one OAM-PM loss test. For example, a row may contain the configurable thresholds for the forward direction for the SLM test belonging to OAM-PM session OAM_PM_Eth_session_1. SROS creates/destroys two rows (forward and backward) in this table for each OAM-PM loss test created/destroyed. A manager creates a loss test using: tmnxOamPmCfgLossLmmRowStatus, tmnxOamPmCfgLossSlmRowStatus, or tmnxOamPmCfgTwampLtRowStatus.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmCfgThrLossFwBwEntry  

tmnxOamPmCfgTestType 1.3.6.1.4.1.6527.3.1.2.92.1.3.13.1.1
The value of tmnxOamPmCfgTestType specifies the test type index of the row. The test types supporting loss thresholds are 'slm(2)', 'twampLight(3)', and 'lmm(4)'.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmTestType  

tmnxOamPmCfgForwardBackward 1.3.6.1.4.1.6527.3.1.2.92.1.3.13.1.2
The value of tmnxOamPmCfgForwardBackward specifies the direction index of the row.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmForwardBackward  

tmnxOamPmCfgThrLossAvgFlrRaise 1.3.6.1.4.1.6527.3.1.2.92.1.3.13.1.3
The value of tmnxOamPmCfgThrLossAvgFlrRaise specifies the raise threshold for the average Frame Loss Ratio (FLR). Depending on the specified indices, tmnxOamPmCfgThrLossAvgFlrRaise is the raise threshold for: tmnxOamPmStsLossSlmAvgFlrFwd, tmnxOamPmStsLossSlmAvgFlrBwd, tmnxOamPmStsLossLmmAvgFlrFwd, tmnxOamPmStsLossLmmAvgFlrBwd, tmnxOamPmStsLossTwlAvgFlrFwd, or tmnxOamPmStsLossTwlAvgFlrBwd. For example, suppose: 1. OAM-PM loss TCAs are enabled for the 'mi15minutes(2)' measurement interval of the OAM-PM session OAM_PM_Eth_session_1 (using tmnxOamPmCfgMeasIntvlLossTCAs and tmnxOamPmCfgMeasIntvlTCAs). 2. tmnxOamPmCfgThrLossAvgFlrRaise is set to 5000 (i.e. 5.000%) for the indices {OAM_PM_Eth_session_1, 'slm(2)', 'forward(1)'}. 3. At the end of a 15 minute interval belonging to OAM_PM_Eth_session_1's SLM test, the average FLR (i.e. tmnxOamPmStsLossSlmAvgFlrFwd) is 5000 (i.e. 5.000%) or more. 4. Generating an average FLR Raise TCA is allowed (e.g. the most recent average FLR TCA for the specified indices was a Clear). Then, SROS generates an average FLR Raise TCA (using tmnxOamPmThrRaise) at the end of the 15-minute interval, for the forward direction. Negative one specifies that average FLR thresholding is disabled for the specified indices (i.e. SROS will not generate a Raise TCA, or a Clear TCA). tmnxOamPmCfgThrLossAvgFlrRaise must be greater than tmnxOamPmCfgThrLossAvgFlrClear. Exception: the combination tmnxOamPmCfgThrLossAvgFlrRaise=-1 and tmnxOamPmCfgThrLossAvgFlrClear=-1 is supported. tmnxOamPmCfgThrLossAvgFlrRaise and tmnxOamPmCfgThrLossAvgFlrClear must be set in the same SNMP Set PDU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1 | 1..100000  

tmnxOamPmCfgThrLossAvgFlrClear 1.3.6.1.4.1.6527.3.1.2.92.1.3.13.1.4
The value of tmnxOamPmCfgThrLossAvgFlrClear specifies the clear threshold for the average Frame Loss Ratio (FLR). Depending on the specified indices, tmnxOamPmCfgThrLossAvgFlrClear is the clear threshold for: tmnxOamPmStsLossSlmAvgFlrFwd, tmnxOamPmStsLossSlmAvgFlrBwd, tmnxOamPmStsLossLmmAvgFlrFwd, tmnxOamPmStsLossLmmAvgFlrBwd, tmnxOamPmStsLossTwlAvgFlrFwd, or tmnxOamPmStsLossTwlAvgFlrBwd. For example, suppose: 1. OAM-PM loss TCAs are enabled for the 'mi15minutes(2)' measurement interval of the OAM-PM session OAM_PM_Eth_session_1 (using tmnxOamPmCfgMeasIntvlLossTCAs and tmnxOamPmCfgMeasIntvlTCAs). 2. tmnxOamPmCfgThrLossAvgFlrClear is set to 4000 (i.e. 4.000%) for the indices {OAM_PM_Eth_session_1, 'slm(2)', 'forward(1)'}. 3. A previous 15 minute interval belonging to OAM_PM_Eth_session_1's SLM test generated an average FLR Raise TCA for the forward direction (see tmnxOamPmCfgThrLossAvgFlrRaise). The TCA has not been cleared. 4. The just-closed 15-minute interval has an average forward FLR for the forward direction (i.e. tmnxOamPmStsLossSlmAvgFlrFwd) of 4000 (i.e. 4.000%), or less. Then, SROS generates an average FLR Clear TCA (using tmnxOamPmThrClear) at the end of the 15-minute interval, for the forward direction. If tmnxOamPmCfgThrLossAvgFlrRaise > 0 AND tmnxOamPmCfgThrLossAvgFlrClear >= 0, average FLR Clear TCAs can be generated for the specified indices. In this case, the maximum number of average FLR TCAs that will be generated for the specified indices across (for example) two 15 minute intervals is two: Raise and Clear. If tmnxOamPmCfgThrLossAvgFlrRaise > 0 AND tmnxOamPmCfgThrLossAvgFlrClear = -1, no average FLR Clear TCAs will be generated for the specified indices. In this case, the maximum number of average FLR TCAs that will be generated for the specified indices across (for example) two 15 minute intervals is two: Raise and Raise. tmnxOamPmCfgThrLossAvgFlrRaise must be greater than tmnxOamPmCfgThrLossAvgFlrClear. Exception: the combination tmnxOamPmCfgThrLossAvgFlrRaise=-1 and tmnxOamPmCfgThrLossAvgFlrClear=-1 is supported. tmnxOamPmCfgThrLossAvgFlrClear and tmnxOamPmCfgThrLossAvgFlrClear must be set in the same SNMP Set PDU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1 | 0..99999  

tmnxOamPmCfgThrLossFwBwAgTable 1.3.6.1.4.1.6527.3.1.2.92.1.3.14
tmnxOamPmCfgThrLossFwBwAgTable contains configured thresholds for OAM Performance Monitoring loss TCAs. The subset of the loss thresholds that are configurable in the forward, backward, and aggregate directions is configured using this table. An aggregate loss threshold applies to the sum of a forward loss counter and a backward loss counter.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmCfgThrLossFwBwAgEntry

tmnxOamPmCfgThrLossFwBwAgEntry 1.3.6.1.4.1.6527.3.1.2.92.1.3.14.1
tmnxOamPmCfgThrLossFwBwAgEntry contains the configured thresholds for the forward, backward, or aggregate direction of one OAM-PM loss test. For example, a row may contain the configurable thresholds for the forward direction for the SLM test belonging to OAM-PM session OAM_PM_Eth_session_1. SROS creates/destroys three rows (forward, backward, and aggregate) in this table for each OAM-PM LMM, SLM or TWAMP-Light test created/destroyed. A manager creates an LMM, SLM or TWAMP-Light test using: tmnxOamPmCfgLossLmmRowStatus, tmnxOamPmCfgLossSlmRowStatus, or tmnxOamPmCfgTwampLtRowStatus.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmCfgThrLossFwBwAgEntry  

tmnxOamPmCfgForwardBackwardAggr 1.3.6.1.4.1.6527.3.1.2.92.1.3.14.1.1
The value of tmnxOamPmCfgForwardBackwardAggr specifies the direction index of the row.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmForwardBackwardAggr  

tmnxOamPmCfgThrLossChliRaise 1.3.6.1.4.1.6527.3.1.2.92.1.3.14.1.2
The value of tmnxOamPmCfgThrLossChliRaise specifies the raise threshold for Consecutive High Loss Intervals (CHLIs). Depending on the specified indices, tmnxOamPmCfgThrLossChliRaise is the raise threshold for: tmnxOamPmStsLossLmmChliBwd, tmnxOamPmStsLossLmmChliFwd + tmnxOamPmStsLossLmmChliBwd, tmnxOamPmStsLossLmmChliFwd, tmnxOamPmStsLossSlmChliBwd, tmnxOamPmStsLossSlmChliFwd + tmnxOamPmStsLossSlmChliBwd, tmnxOamPmStsLossSlmChliFwd, tmnxOamPmStsLossTwlChliBwd, tmnxOamPmStsLossTwlChliFwd + tmnxOamPmStsLossTwlChliBwd, or tmnxOamPmStsLossTwlChliFwd. For example, suppose: 1. OAM-PM loss TCAs are enabled for the 'mi15minutes(2)' measurement interval of the OAM-PM session OAM_PM_Eth_session_1 (using tmnxOamPmCfgMeasIntvlLossTCAs and tmnxOamPmCfgMeasIntvlTCAs). 2. tmnxOamPmCfgThrLossChliRaise is set to 7 for the indices {OAM_PM_Eth_session_1, 'slm(2)', 'forward(1)'}. 3. A 15 minute interval belonging to OAM_PM_Eth_session_1's SLM test has its forward CHLI count (i.e. tmnxOamPmStsLossSlmChliFwd) increase to 7. 4. Generating a CHLI Raise TCA is allowed (e.g. the most recent CHLI TCA for the specified indices was a Clear). Then, SROS immediately generates a CHLI Raise TCA (using tmnxOamPmThrRaise) for the 15-minute interval, for the forward direction. Negative one specifies that CHLI thresholding is disabled for the specified indices (i.e. SROS will not generate a Raise TCA, or a Clear TCA). tmnxOamPmCfgThrLossChliRaise must be greater than tmnxOamPmCfgThrLossChliClear. Exception: the combination tmnxOamPmCfgThrLossChliRaise=-1 and tmnxOamPmCfgThrLossChliClear=-1 is supported. tmnxOamPmCfgThrLossChliRaise and tmnxOamPmCfgThrLossChliClear must be set in the same SNMP Set PDU. The upper bound of this object is the maximum number of MEF-35 'delta_t' time intervals (also known as 'Small Time Intervals') which can occur in a 24 hour measurement interval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1 | 1..864000  

tmnxOamPmCfgThrLossChliClear 1.3.6.1.4.1.6527.3.1.2.92.1.3.14.1.3
The value of tmnxOamPmCfgThrLossChliClear specifies the clear threshold for Consecutive High Loss Intervals (CHLIs). tmnxOamPmCfgThrLossChliClear is the clear threshold for the list of counters specified in the tmnxOamPmCfgThrLossChliRaise DESCRIPTION clause. For example, suppose: 1. OAM-PM loss TCAs are enabled for the 'mi15minutes(2)' measurement interval of the OAM-PM session OAM_PM_Eth_session_1 (using tmnxOamPmCfgMeasIntvlLossTCAs and tmnxOamPmCfgMeasIntvlTCAs). 2. tmnxOamPmCfgThrLossChliClear is set to 5 for the indices {OAM_PM_Eth_session_1, 'slm(2)', 'forward(1)'}. 3. A previous 15 minute interval belonging to OAM_PM_Eth_session_1's SLM test generated a CHLI Raise TCA for the forward direction (see tmnxOamPmCfgThrLossChliRaise). The TCA has not been cleared. 4. The just-closed 15-minute interval has an forward CHLI count for the forward direction (i.e. tmnxOamPmStsLossSlmChliFwd) of 5, or less. Then, SROS generates a CHLI Clear TCA (using tmnxOamPmThrClear) for the 15-minute interval, for the forward direction. If tmnxOamPmCfgThrLossChliRaise>0 AND tmnxOamPmCfgThrLossChliClear>=0, CHLI Clear TCAs can be generated for the specified indices. In this case, the maximum number of CHLI TCAs that will be generated for the specified indices across (for example) two 15 minute intervals is two: Raise and Clear. If tmnxOamPmCfgThrLossChliRaise>0 AND tmnxOamPmCfgThrLossChliClear=-1, no CHLI Clear TCAs will be generated for the specified indices. In this case, the maximum number of CHLI TCAs that will be generated for the specified indices across (for example) two 15 minute intervals is two: Raise and Raise. tmnxOamPmCfgThrLossChliRaise must be greater than tmnxOamPmCfgThrLossChliClear. Exception: the combination tmnxOamPmCfgThrLossChliRaise=-1 and tmnxOamPmCfgThrLossChliClear=-1 is supported. tmnxOamPmCfgThrLossChliClear and tmnxOamPmCfgThrLossChliClear must be set in the same SNMP Set PDU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1 | 0..863999  

tmnxOamPmCfgThrLossHliRaise 1.3.6.1.4.1.6527.3.1.2.92.1.3.14.1.4
The value of tmnxOamPmCfgThrLossHliRaise specifies the raise threshold for High Loss Intervals (HLIs). tmnxOamPmCfgThrLossHliRaise has the same operating principles as tmnxOamPmCfgThrLossChliRaise. Depending on the specified indices, tmnxOamPmCfgThrLossHliRaise is the raise threshold for: tmnxOamPmStsLossLmmHliBwd, tmnxOamPmStsLossLmmHliFwd + tmnxOamPmStsLossLmmHliBwd, tmnxOamPmStsLossLmmHliFwd, tmnxOamPmStsLossSlmHliBwd, tmnxOamPmStsLossSlmHliFwd + tmnxOamPmStsLossSlmHliBwd, tmnxOamPmStsLossSlmHliFwd, tmnxOamPmStsLossTwlHliBwd, tmnxOamPmStsLossTwlHliFwd + tmnxOamPmStsLossTwlHliBwd, or tmnxOamPmStsLossTwlHliFwd.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1 | 1..864000  

tmnxOamPmCfgThrLossHliClear 1.3.6.1.4.1.6527.3.1.2.92.1.3.14.1.5
The value of tmnxOamPmCfgThrLossHliClear specifies the clear threshold for High Loss Intervals (HLIs). tmnxOamPmCfgThrLossHliClear has the same operating principles as tmnxOamPmCfgThrLossChliClear. tmnxOamPmCfgThrLossHliClear is the clear threshold for the list of counters specified in the tmnxOamPmCfgThrLossHliRaise DESCRIPTION clause.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1 | 0..863999  

tmnxOamPmCfgThrLossUnavlIndRaise 1.3.6.1.4.1.6527.3.1.2.92.1.3.14.1.6
The value of tmnxOamPmCfgThrLossUnavlIndRaise specifies the raise threshold for the number of availability indicators evaluated as Unavailable. tmnxOamPmCfgThrLossUnavlIndRaise has the same operating principles as tmnxOamPmCfgThrLossChliRaise. Depending on the specified indices, tmnxOamPmCfgThrLossUnavlIndRaise is the raise threshold for: tmnxOamPmStsLossLmmUnavlIndBwd, tmnxOamPmStsLossLmmUnavlIndFwd + tmnxOamPmStsLossLmmUnavlIndBwd, tmnxOamPmStsLossLmmUnavlIndFwd, tmnxOamPmStsLossSlmUnavlIndBwd, tmnxOamPmStsLossSlmUnavlIndFwd + tmnxOamPmStsLossSlmUnavlIndBwd, tmnxOamPmStsLossSlmUnavlIndFwd, tmnxOamPmStsLossTwlUnavlIndBwd, tmnxOamPmStsLossTwlUnavlIndFwd + tmnxOamPmStsLossTwlUnavlIndBwd, or tmnxOamPmStsLossTwlUnavlIndFwd.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1 | 1..864000  

tmnxOamPmCfgThrLossUnavlIndClear 1.3.6.1.4.1.6527.3.1.2.92.1.3.14.1.7
The value of tmnxOamPmCfgThrLossUnavlIndClear specifies the clear threshold for the number of availability indicators evaluated as Unavailable. tmnxOamPmCfgThrLossUnavlIndClear has the same operating principles as tmnxOamPmCfgThrLossChliClear. tmnxOamPmCfgThrLossUnavlIndClear is the clear threshold for the list of counters specified in the tmnxOamPmCfgThrLossUnavlIndRaise DESCRIPTION clause.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1 | 0..863999  

tmnxOamPmCfgThrLossUndtAvlRaise 1.3.6.1.4.1.6527.3.1.2.92.1.3.14.1.8
The value of tmnxOamPmCfgThrLossUndtAvlRaise specifies the raise threshold for the number of availability indicators evaluated as Available based on extrapolation from the previous state. tmnxOamPmCfgThrLossUndtAvlRaise has the same operating principles as tmnxOamPmCfgThrLossChliRaise. Depending on the specified indices, tmnxOamPmCfgThrLossUndtAvlRaise is the raise threshold for: tmnxOamPmStsLossLmmUndtAvlBwd, tmnxOamPmStsLossLmmUndtAvlFwd + tmnxOamPmStsLossLmmUndtAvlBwd, tmnxOamPmStsLossLmmUndtAvlFwd, tmnxOamPmStsLossSlmUndtAvlBwd, tmnxOamPmStsLossSlmUndtAvlFwd + tmnxOamPmStsLossSlmUndtAvlBwd, tmnxOamPmStsLossSlmUndtAvlFwd, tmnxOamPmStsLossTwlUndtAvlBwd, tmnxOamPmStsLossTwlUndtAvlFwd + tmnxOamPmStsLossTwlUndtAvlBwd, or tmnxOamPmStsLossTwlUndtAvlFwd.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1 | 1..864000  

tmnxOamPmCfgThrLossUndtAvlClear 1.3.6.1.4.1.6527.3.1.2.92.1.3.14.1.9
The value of tmnxOamPmCfgThrLossUndtAvlClear specifies the clear threshold for the number of availability indicators evaluated as Available based on extrapolation from the previous state. tmnxOamPmCfgThrLossUndtAvlClear has the same operating principles as tmnxOamPmCfgThrLossChliClear. tmnxOamPmCfgThrLossUndtAvlClear is the clear threshold for the list of counters specified in the tmnxOamPmCfgThrLossUndtAvlRaise DESCRIPTION clause.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1 | 0..863999  

tmnxOamPmCfgThrLossUndtUnavlRais 1.3.6.1.4.1.6527.3.1.2.92.1.3.14.1.10
The value of tmnxOamPmCfgThrLossUndtUnavlRais specifies the raise threshold for the number of availability indicators evaluated as Unavailable based on extrapolation from the previous state. tmnxOamPmCfgThrLossUndtUnavlRais has the same operating principles as tmnxOamPmCfgThrLossChliRaise. Depending on the specified indices, tmnxOamPmCfgThrLossUndtUnavlRais is the raise threshold for: tmnxOamPmStsLossLmmUndtUnavlBwd, tmnxOamPmStsLossLmmUndtUnavlFwd + tmnxOamPmStsLossLmmUndtUnavlBwd, tmnxOamPmStsLossLmmUndtUnavlFwd, tmnxOamPmStsLossSlmUndtUnavlBwd, tmnxOamPmStsLossSlmUndtUnavlFwd + tmnxOamPmStsLossSlmUndtUnavlBwd, tmnxOamPmStsLossSlmUndtUnavlFwd, tmnxOamPmStsLossTwlUndtUnavlBwd, tmnxOamPmStsLossTwlUndtUnavlFwd + tmnxOamPmStsLossTwlUndtUnavlBwd, or tmnxOamPmStsLossTwlUndtUnavlFwd.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1 | 1..864000  

tmnxOamPmCfgThrLossUndtUnavlClr 1.3.6.1.4.1.6527.3.1.2.92.1.3.14.1.11
The value of tmnxOamPmCfgThrLossUndtUnavlClr specifies the clear threshold for the number of availability indicators evaluated as Unavailable based on extrapolation from the previous state. tmnxOamPmCfgThrLossUndtUnavlClr has the same operating principles as tmnxOamPmCfgThrLossChliClear. tmnxOamPmCfgThrLossUndtUnavlClr is the clear threshold for the list of counters specified in the tmnxOamPmCfgThrLossUndtUnavlRais DESCRIPTION clause.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1 | 0..863999  

tmnxOamPmCfgThrDelayTable 1.3.6.1.4.1.6527.3.1.2.92.1.3.15
tmnxOamPmCfgThrDelayTable contains threshold configuration for OAM Performance Monitoring delay TCAs.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmCfgThrDelayEntry

tmnxOamPmCfgThrDelayEntry 1.3.6.1.4.1.6527.3.1.2.92.1.3.15.1
tmnxOamPmCfgThrDelayEntry contains the threshold configuration for one OAM-PM bin group, bin type, and direction. For example, a row may contain the threshold configuration for bin group 255, bin type 'ifdv(3)', and direction 'twoWay(3)'. SROS creates/destroys nine rows (i.e. {'fd(1)', 'fdr(2)', 'ifdv(3)'} x {'forward(1)', 'backward(2)', 'twoWay(3)'}) when an OAM-PM bin group is created/destroyed. A manager creates/destroys an OAM-PM bin group using tmnxOamPmCfgBinGroupRowStatus. The objects in this table cannot be changed from the default value when the index value tmnxOamPmCfgBinGroupId is 1.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmCfgThrDelayEntry  

tmnxOamPmCfgForwardBackward2Way 1.3.6.1.4.1.6527.3.1.2.92.1.3.15.1.1
The value of tmnxOamPmCfgForwardBackward2Way specifies the direction of the row to be configured or read.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmForwardBackwardTwoWay  

tmnxOamPmCfgThrDelayLowestBin 1.3.6.1.4.1.6527.3.1.2.92.1.3.15.1.2
The value of tmnxOamPmCfgThrDelayLowestBin specifies the lowest OAM-PM delay bin to be used when applying a configured Raise or Clear delay threshold. The usage is described in the tmnxOamPmCfgThrDelayRaise and tmnxOamPmCfgThrDelayClear DESCRIPTION clauses.
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0..9  

tmnxOamPmCfgThrDelayRaise 1.3.6.1.4.1.6527.3.1.2.92.1.3.15.1.3
The value of tmnxOamPmCfgThrDelayRaise specifies the OAM-PM raise threshold for excessive delay. For example, suppose: 1. tmnxOamPmCfgThrDelayRaise=1000 and tmnxOamPmCfgThrDelayLowestBin=7 for the index values 255, 'ifdv(3)', 'twoWay(3)'. 2. Bin group 255 has been configured with 10 Inter-Frame Delay Variation (IFDV) bins (numbered 0..9), using tmnxOamPmCfgBinGroupIfdvBinCount. 3. The OAM-PM session 'oamPmSession1' is configured to use bin group 255 (using tmnxOamPmCfgSessBinGroupId). 4. OAM-PM delay TCAs are enabled for the measurement interval with indices 'oamPmSession1', 'mi15Minutes(2)' (using tmnxOamPmCfgMeasIntvlDelayTCAs and tmnxOamPmCfgMeasIntvlTCAs). 5. During a 15 minute interval belonging to a DMM test which belongs to 'oamPmSession1', the following inequality becomes true (where only the last two indices of the object are shown, and the last index is a bin number): tmnxOamPmStsDelayDmmBin2wyCount.ifdv(3).7 + tmnxOamPmStsDelayDmmBin2wyCount.ifdv(3).8 + tmnxOamPmStsDelayDmmBin2wyCount.ifdv(3).9 >= 1000 Then, a delay Raise TCA (using tmnxOamPmThrRaise) will be generated immediately. The TCA suppression and configuration rules for tmnxOamPmCfgThrDelayRaise and tmnxOamPmCfgThrDelayClear are the same as the rules for tmnxOamPmCfgThrLossChliRaise and tmnxOamPmCfgThrLossChliClear. The upper bound of this object is the maximum number of DMM PDUs (or TWAMP-Test PDUs) which can be sent in the longest supported (i.e. 24 hour) measurement interval.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1 | 1..864000  

tmnxOamPmCfgThrDelayClear 1.3.6.1.4.1.6527.3.1.2.92.1.3.15.1.4
The value of tmnxOamPmCfgThrDelayClear specifies the OAM-PM clear threshold for excessive delay. For example, suppose: 1. tmnxOamPmCfgThrDelayClear=900 and tmnxOamPmCfgThrDelayLowestBin=7 for the index values 255, 'ifdv(3)', 'twoWay(3)'. 2. Bin group 255 has been configured with 10 Inter-Frame Delay Variation (IFDV) bins (numbered 0..9), using tmnxOamPmCfgBinGroupIfdvBinCount. 3. The OAM-PM session 'oamPmSession1' is configured to use bin group 255 (using tmnxOamPmCfgSessBinGroupId). 4. OAM-PM delay TCAs are enabled for the measurement interval with indices 'oamPmSession1', 'mi15Minutes(2)' (using tmnxOamPmCfgMeasIntvlDelayTCAs and tmnxOamPmCfgMeasIntvlTCAs). 5. At the end of a 15 minute interval belonging to a DMM test which belongs to 'oamPmSession1', the following inequality is true (where only the last two indices of the object are shown, and the last index is a bin number): tmnxOamPmStsDelayDmmBin2wyCount.ifdv(3).7 + tmnxOamPmStsDelayDmmBin2wyCount.ifdv(3).8 + tmnxOamPmStsDelayDmmBin2wyCount.ifdv(3).9 <= 900 6. Generating a delay Clear TCA is allowed (i.e. the most recent delay TCA for the specified indices was a Raise). Then, a delay Clear TCA (using tmnxOamPmThrClear) will be generated. The TCA suppression and configuration rules for tmnxOamPmCfgThrDelayRaise and tmnxOamPmCfgThrDelayClear are the same as the rules for tmnxOamPmCfgThrLossChliRaise and tmnxOamPmCfgThrLossChliClear.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 -1 | 0..863999  

tmnxOamPmCfgThrDelayExclBinFrTca 1.3.6.1.4.1.6527.3.1.2.92.1.3.15.1.5
The value of tmnxOamPmCfgThrDelayExclBinFrTca specifies the bin number of the lowest delay bin to be excluded from the OAM-PM TCA calculations for the specified bin group, bin type, and direction. Configuring tmnxOamPmCfgThrDelayExclBinFrTca allows outlier high delay frames to be ignored when deciding to raise or clear a delay TCA. For example, suppose the following values are configured for bin group 255. Object Value ---------------------------------------------------- ----- tmnxOamPmCfgBinGroupFdBinCount.255 10 tmnxOamPmCfgThrDelayLowestBin.255.fd(1).forward(1) 6 tmnxOamPmCfgThrDelayExclBinFrTca.255.fd(1).forward(1) 8 Then, the decision to raise or clear a Frame Delay (FD) TCA for the forward direction will be made based on the packet counts in bins 6 and 7 (while ignoring the packet counts in bins 8 and 9). Configuring tmnxOamPmCfgThrDelayExclBinFrTca to the value -1 specifies that no bins are to be excluded. Configuring tmnxOamPmCfgThrDelayExclBinFrTca does not affect the value of delay bin packet counters (e.g. tmnxOamPmStsDelayDmmBinFwdCount). An attempt to change tmnxOamPmCfgThrDelayExclBinFrTca to a non-default value will be rejected if the specified bin does not exist. Bins are created using: tmnxOamPmCfgBinGroupFdBinCount, tmnxOamPmCfgBinGroupFdrBinCount, tmnxOamPmCfgBinGroupIfdvBinCount, and tmnxOamPmCfgBinGroupRowStatus. An attempt to change tmnxOamPmCfgThrDelayExclBinFrTca to a non-default value will be rejected if tmnxOamPmCfgThrDelayExclBinFrTca is less than or equal to tmnxOamPmCfgThrDelayLowestBin. An attempt to change tmnxOamPmCfgThrDelayExclBinFrTca will be rejected if the specified bin group (i.e. tmnxOamPmCfgBinGroupId) is 1. tmnxOamPmCfgThrDelayExclBinFrTca can be changed regardless of the specified bin group's administrative status (i.e. tmnxOamPmCfgBinGroupAdminStatus).
Status: current Access: read-write
OBJECT-TYPE    
  TmnxOamPmCfgBinNumOrNone  

tmnxOamPmCfgBinGrpTypeDirTable 1.3.6.1.4.1.6527.3.1.2.92.1.3.16
tmnxOamPmCfgBinGrpTypeDirTable contains configuration information for the delay bins to be excluded from OAM Performance Monitoring average delay calculations.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmCfgBinGrpTypeDirEntry

tmnxOamPmCfgBinGrpTypeDirEntry 1.3.6.1.4.1.6527.3.1.2.92.1.3.16.1
tmnxOamPmCfgBinGrpTypeDirEntry contains the delay bins to be excluded from OAM-PM average delay calculations for one OAM-PM bin group, bin type, and direction.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmCfgBinGrpTypeDirEntry  

tmnxOamPmCfgBgTyDirExclBinsFrAvg 1.3.6.1.4.1.6527.3.1.2.92.1.3.16.1.1
The value of tmnxOamPmCfgBgTyDirExclBinsFrAvg specifies the set of delay bins to be excluded from OAM-PM average delay calculations for the specified bin group, bin type, and direction. Configuring a set of delay bins using tmnxOamPmCfgBgTyDirExclBinsFrAvg allows outlier delay values to be excluded from average delay calculations. For example, suppose tmnxOamPmCfgBgTyDirExclBinsFrAvg has the value { bin0, bin9 } for bin group 255, bin type 'ifdv(3)', and the forward direction. Suppose the configured lower bounds for {bin group 255, bin type 'ifdv(3)'} are as follows. Bin Number Lower Bound (microseconds) ---------- -------------------------- 0 0 (not configurable) 1 1 2 5000 3 10000 4 15000 5 20000 6 25000 7 30000 8 35000 9 40000 Then, the average forward IFDV delay calculations for tests using bin group 255 will ignore any delay measurement that is less than 1 microsecond, or greater than or equal to 40000 microseconds. The following objects present the result of an average delay calculation: tmnxOamPmStsDelayDmmFwdAvg, tmnxOamPmStsDelayDmmBwdAvg, tmnxOamPmStsDelayDmm2wyAvg, tmnxOamPmStsDelayTwlFwdAvg, tmnxOamPmStsDelayTwlBwdAvg, and tmnxOamPmStsDelayTwl2wyAvg. Configuring tmnxOamPmCfgBgTyDirExclBinsFrAvg does not affect minimum delay or maximum delay calculations. An attempt to change tmnxOamPmCfgBgTyDirExclBinsFrAvg will be rejected if the specified bin group (i.e. tmnxOamPmCfgBinGroupId) is 1. An attempt to change tmnxOamPmCfgBgTyDirExclBinsFrAvg will be rejected if the specified bin group's administrative status (i.e. tmnxOamPmCfgBinGroupAdminStatus) is enabled.
Status: current Access: read-write
OBJECT-TYPE    
  TmxnOamPmBinNums  

tmnxOamPmStsBaseTable 1.3.6.1.4.1.6527.3.1.2.92.2.2.1
tmnxOamPmStsBaseTable contains the base statistics for OAM Performance Monitoring Measurement Interval Data Sets. The statistics in this table are common to all test types (e.g. DMM and SLM tests).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmStsBaseEntry

tmnxOamPmStsBaseEntry 1.3.6.1.4.1.6527.3.1.2.92.2.2.1.1
tmnxOamPmStsBaseEntry contains the base statistics for one OAM Performance Monitoring Measurement Interval Data Set. Rows are created in this table when a test is started (e.g. using tmnxOamPmCfgDelayDmmAdminStatus and tmnxOamPmCfgDelayDmmOnDmndStatus). At that time, a row for the current interval (with the index value tmnxOamPmStsIntvlNum=1) is created for each row with a matching session name in tmnxOamPmCfgMeasIntvlTable. In addition, a row is created in this table for the test's 'miRaw(1)' interval. After that, the timed creation and destruction of rows in this table is explained using the following example. Suppose the configured number of intervals to be retained is as follows (where index columns are underlined with octothorpes, and 'tmnxOamPm' is abbreviated as '_'): _CfgSessName _CfgMeasIntvlDuration _CfgMeasIntvlsStored ############ ##################### -------------------- 'mySess1' 'mi15Minutes(2)' 3 Suppose statistics collection started at t = 0 (minutes). Suppose the following rows exist in tmnxOamPmStsBaseTable at t = 59 (minutes): _CfgSessName _StsBaseTestType _StsIntvlDuration _StsIntvlNum ############ ################ ################# ############ 'mySess1' 'dmm(1)' 'mi15Minutes(2)' 1 'mySess1' 'dmm(1)' 'mi15Minutes(2)' 2 'mySess1' 'dmm(1)' 'mi15Minutes(2)' 3 'mySess1' 'dmm(1)' 'mi15Minutes(2)' 4 The interval numbers are assigned as follows: 1 - the historical interval ended at t = 15 minutes 2 - the historical interval ended at t = 30 minutes 3 - the historical interval ended at t = 45 minutes 4 - the current interval Then, after the next 15 minute interval ends (e.g. at t = 61 minutes), the following rows will exist: _CfgSessName _StsBaseTestType _StsIntvlDuration _StsIntvlNum ############ ################ ################# ############ 'mySess1' 'dmm(1)' 'mi15Minutes(2)' 2 'mySess1' 'dmm(1)' 'mi15Minutes(2)' 3 'mySess1' 'dmm(1)' 'mi15Minutes(2)' 4 'mySess1' 'dmm(1)' 'mi15Minutes(2)' 5 The interval numbers are assigned as follows: 2 - the historical interval ended at t = 30 minutes 3 - the historical interval ended at t = 45 minutes 4 - the historical interval ended at t = 60 minutes 5 - the current interval The row with interval number 1 was destroyed, because tmnxOamPmCfgMeasIntvlsStored=3 specifies that at most three historical intervals be retained. Rows are also destroyed in this table when the corresponding tmnxOamPmCfgMeasIntvlTable row is destroyed. When the index value tmnxOamPmStsMeasIntvlDuration is 'miRaw(1)', only one interval is available (i.e. tmnxOamPmStsIntvlNum = 1). When a test is running, the measurement interval data set for a test's 'miRaw(1)' measurement interval duration can be cleared using TIMETRA-CLEAR-MIB::tmnxClearAction and tmnxClearParams. The change to the objects in the specified row is as follows. Object Change on Clear Operation ---------------------------- -------------------------------------- tmnxOamPmStsBaseOperStatus No change tmnxOamPmStsBaseSuspect Set to 'true(1)' tmnxOamPmStsBaseStartTime Set to UTC time of the clear operation tmnxOamPmStsBaseElapsedTime Set to zero tmnxOamPmStsBaseTestFramesTx Set to zero tmnxOamPmStsBaseTestFramesRx Set to zero Measurement interval data sets for measurement interval durations other than 'miRaw(1)' cannot be cleared.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmStsBaseEntry  

tmnxOamPmStsBaseTestType 1.3.6.1.4.1.6527.3.1.2.92.2.2.1.1.1
The value of tmnxOamPmStsBaseTestType specifies the type of test for which statistics are to be read (e.g. 'dmm(1)').
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmTestType  

tmnxOamPmStsMeasIntvlDuration 1.3.6.1.4.1.6527.3.1.2.92.2.2.1.1.2
The value of tmnxOamPmStsMeasIntvlDuration specifies the duration of the interval of the statistics to be read (e.g. 'mi15Minutes(2)').
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmMeasIntervalDuration  

tmnxOamPmStsIntvlNum 1.3.6.1.4.1.6527.3.1.2.92.2.2.1.1.3
The value of tmnxOamPmStsIntvlNum specifies the interval number of the statistics to be read. The system's creation and destruction of interval numbers is described in the tmnxOamPmStsBaseEntry DESCRIPTION clause.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmStsIntvlNum  

tmnxOamPmStsBaseOperStatus 1.3.6.1.4.1.6527.3.1.2.92.2.2.1.1.4
The value of tmnxOamPmStsBaseOperStatus indicates the operational status of the specified measurement interval data set. If the interval is historical and the operational status is 'inProgress(1)', the interval is closing (i.e. waiting for a response for the final test request sent).
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER inProgress(1), completed(2)  

tmnxOamPmStsBaseSuspect 1.3.6.1.4.1.6527.3.1.2.92.2.2.1.1.5
The value of tmnxOamPmStsBaseSuspect indicates whether or not the specified measurement interval data set contains suspect information.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

tmnxOamPmStsBaseStartTime 1.3.6.1.4.1.6527.3.1.2.92.2.2.1.1.6
The value of tmnxOamPmStsBaseStartTime indicates the start time (in UTC) of the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime Size(8)  

tmnxOamPmStsBaseElapsedTime 1.3.6.1.4.1.6527.3.1.2.92.2.2.1.1.7
The value of tmnxOamPmStsBaseElapsedTime indicates the time elapsed since data collection started for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsBaseTestFramesTx 1.3.6.1.4.1.6527.3.1.2.92.2.2.1.1.8
The value of tmnxOamPmStsBaseTestFramesTx indicates the number of test frames sent for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsBaseTestFramesRx 1.3.6.1.4.1.6527.3.1.2.92.2.2.1.1.9
The value of tmnxOamPmStsBaseTestFramesRx indicates the number of test frames received for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsMeasIntvlIndexTable 1.3.6.1.4.1.6527.3.1.2.92.2.2.2
tmnxOamPmStsMeasIntvlIndexTable contains the interval number of the newest interval for all the active combinations of session, test type (e.g. 'dmm(1)'), and interval duration (e.g. 'mi15Minutes(2)').
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmStsMeasIntvlIndexEntry

tmnxOamPmStsMeasIntvlIndexEntry 1.3.6.1.4.1.6527.3.1.2.92.2.2.2.1
tmnxOamPmStsMeasIntvlIndexEntry contains the interval number of the newest interval for the specified combination of session, test type (e.g. 'dmm(1)'), and interval duration (e.g. 'mi15Minutes(2)'). Rows are created in this table when a test is enabled (e.g. using tmnxOamPmCfgDelayDmmAdminStatus and tmnxOamPmCfgDelayDmmOnDmndStatus). A row is destroyed in this table when the corresponding tmnxOamPmCfgMeasIntvlTable row is destroyed.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmStsMeasIntvlIndexEntry  

tmnxOamPmStsMeasIntvlIndexNewest 1.3.6.1.4.1.6527.3.1.2.92.2.2.2.1.1
The value of tmnxOamPmStsMeasIntvlIndexNewest indicates the interval number of the newest interval for the specified session, test type (e.g. 'dmm(1)'), and interval duration (e.g. 'mi15Minutes(2)'). This value is provided as the tmnxOamPmStsIntvlNum index value when reading a row for the newest interval in an OAM-PM statistics table. For a running test, the newest interval is the current interval. For a stopped test, the newest interval is the most recent historical interval. A stopped test does not have a current interval. The interval number of the oldest interval for the specified session, test type, and interval duration can be computed from this value. For a running test, the formula is interval_number_of_the_oldest_interval = MAX(tmnxOamPmStsMeasIntvlIndexNewest-tmnxOamPmCfgMeasIntvlsStored, 1). For a stopped test, the formula is interval_number_of_the_oldest_interval = MAX(tmnxOamPmStsMeasIntvlIndexNewest-tmnxOamPmCfgMeasIntvlsStored+1,1).
Status: current Access: read-only
OBJECT-TYPE    
  TmnxOamPmStsIntvlNum  

tmnxOamPmStsLossSlmTable 1.3.6.1.4.1.6527.3.1.2.92.2.2.3
tmnxOamPmStsLossSlmTable contains the frame loss statistics for OAM Performance Monitoring SLM (Synthetic Loss Measurement) tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmStsLossSlmEntry

tmnxOamPmStsLossSlmEntry 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1
tmnxOamPmStsLossSlmEntry contains the SLM test statistics for one OAM Performance Monitoring Measurement Interval Data Set. A row is created in this table when a tmnxOamPmStsBaseTable row is created with tmnxOamPmStsBaseTestType = 'slm(2)'. A row is destroyed in this table when the corresponding tmnxOamPmStsBaseTable row is destroyed. When a test is running, the SLM statistics for a test's raw (i.e. 'miRaw(1)') measurement interval duration can be cleared using TIMETRA-CLEAR-MIB::tmnxClearAction and tmnxClearParams. A successful clear operation zeros all the raw SLM statistics for the specified session.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmStsLossSlmEntry  

tmnxOamPmStsLossSlmTxFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.1
The value of tmnxOamPmStsLossSlmTxFwd indicates the number of SLM request frames transmitted in the forward direction for the specified measurement interval data set. A frame is counted if the SLM Availability state is Available at transmit time (as specified in MEF-35 Section 9.2.5). A simple count of the frames transmitted for the test is available in tmnxOamPmStsBaseTestFramesTx.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsLossSlmRxFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.2
The value of tmnxOamPmStsLossSlmRxFwd indicates the number of SLM request frames received in the forward direction for the specified measurement interval data set. A frame is counted if the SLM Availability state is Available at receive time (as specified in MEF-35 Section 9.2.5). A simple count of the frames received for the test is available in tmnxOamPmStsBaseTestFramesRx.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsLossSlmTxBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.3
The value of tmnxOamPmStsLossSlmTxBwd indicates the number of SLR reply frames transmitted in the backward direction for the specified measurement interval data set. A frame is counted if the SLM Availability state is Available at transmit time (as specified in MEF-35 Section 9.2.5). A simple count of the frames transmitted for the test is available in tmnxOamPmStsBaseTestFramesTx.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsLossSlmRxBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.4
The value of tmnxOamPmStsLossSlmRxBwd indicates the number of SLR reply frames received in the backward direction for the specified measurement interval data set. A frame is counted if the SLM Availability state is Available at receive time (as specified in MEF-35 Section 9.2.5). A simple count of the frames received for the test is available in tmnxOamPmStsBaseTestFramesRx.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsLossSlmAvailIndFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.5
The value of tmnxOamPmStsLossSlmAvailIndFwd indicates the number of availability indicators evaluated as Available in the forward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsLossSlmAvailIndBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.6
The value of tmnxOamPmStsLossSlmAvailIndBwd indicates the number of availability indicators evaluated as Available in the backward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsLossSlmUnavlIndFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.7
The value of tmnxOamPmStsLossSlmUnavlIndFwd indicates the number of availability indicators evaluated as Unavailable in the forward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsLossSlmUnavlIndBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.8
The value of tmnxOamPmStsLossSlmUnavlIndBwd indicates the number of availability indicators evaluated as Unavailable in the backward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsLossSlmUndtAvlFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.9
The value of tmnxOamPmStsLossSlmUndtAvlFwd indicates the number of availability indicators evaluated as Available in the forward direction based on extrapolation from the previous state. For example, this counter will be incremented when: 1. It is time to calculate an availability indicator, and 2. All the probe requests used to calculate the availability indicator have timed out, and 3. The most recently declared availability indicator in the forward direction was Available. In that case, the result is considered undetermined because no information is available to indicate if the problem is in the forward direction or the backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsLossSlmUndtUnavlFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.10
The value of tmnxOamPmStsLossSlmUndtUnavlFwd indicates the number of availability indicators evaluated as Unavailable in the forward direction based on extrapolation from the previous state. For example, this counter will be incremented when: 1. It is time to calculate an availability indicator, and 2. All the probe requests used to calculate the availability indicator have timed out, and 3. The most recently declared availability indicator in the forward direction was Unavailable. In that case, the result is considered undetermined because no information is available to indicate if the problem is in the forward direction or the backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsLossSlmUndtAvlBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.11
The value of tmnxOamPmStsLossSlmUndtAvlBwd indicates the number of availability indicators evaluated as Available in the backward direction based on extrapolation from the previous state. For example, this counter will be incremented when: 1. It is time to calculate an availability indicator, and 2. All the probe requests used to calculate the availability indicator have timed out, and 3. The most recently declared availability indicator in the backward direction was Available. In that case, the result is considered undetermined because no information is available to indicate if the problem is in the forward direction or the backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsLossSlmUndtUnavlBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.12
The value of tmnxOamPmStsLossSlmUndtUnavlBwd indicates the number of availability indicators evaluated as Unavailable in the backward direction based on extrapolation from the previous state. For example, this counter will be incremented when: 1. It is time to calculate an availability indicator, and 2. All the probe requests used to calculate the availability indicator have timed out, and 3. The most recently declared availability indicator in the backward direction was Unavailable. In that case, the result is considered undetermined because no information is available to indicate if the problem is in the forward direction or the backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsLossSlmHliFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.13
The value of tmnxOamPmStsLossSlmHliFwd indicates the number of High Loss Intervals (HLIs) in the forward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsLossSlmHliBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.14
The value of tmnxOamPmStsLossSlmHliBwd indicates the number of High Loss Intervals (HLIs) in the backward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsLossSlmChliFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.15
The value of tmnxOamPmStsLossSlmChliFwd indicates the number of Consecutive High Loss Intervals (CHLIs) in the forward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsLossSlmChliBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.16
The value of tmnxOamPmStsLossSlmChliBwd indicates the number of Consecutive High Loss Intervals (CHLIs) in the backward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsLossSlmMinFlrFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.17
The value of tmnxOamPmStsLossSlmMinFlrFwd indicates the minimum Frame Loss Ratio (FLR) in the forward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

tmnxOamPmStsLossSlmMaxFlrFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.18
The value of tmnxOamPmStsLossSlmMaxFlrFwd indicates the maximum Frame Loss Ratio (FLR) in the forward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

tmnxOamPmStsLossSlmAvgFlrFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.19
The value of tmnxOamPmStsLossSlmAvgFlrFwd indicates the average Frame Loss Ratio (FLR) in the forward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

tmnxOamPmStsLossSlmMinFlrBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.20
The value of tmnxOamPmStsLossSlmMinFlrBwd indicates the minimum Frame Loss Ratio (FLR) in the backward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

tmnxOamPmStsLossSlmMaxFlrBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.21
The value of tmnxOamPmStsLossSlmMaxFlrBwd indicates the maximum Frame Loss Ratio (FLR) in the backward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

tmnxOamPmStsLossSlmAvgFlrBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.3.1.22
The value of tmnxOamPmStsLossSlmAvgFlrBwd indicates the average Frame Loss Ratio (FLR) in the backward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

tmnxOamPmStsDelayDmmTable 1.3.6.1.4.1.6527.3.1.2.92.2.2.4
tmnxOamPmStsDelayDmmTable contains the summarized DMM (Delay Measurement Message) statistics for OAM Performance Monitoring Measurement Interval Data Sets.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmStsDelayDmmEntry

tmnxOamPmStsDelayDmmEntry 1.3.6.1.4.1.6527.3.1.2.92.2.2.4.1
tmnxOamPmStsDelayDmmEntry contains the summarized DMM (Delay Measurement Message) statistics for one OAM Performance Monitoring Measurement Interval Data Set. When a row is created in tmnxOamPmStsBaseTable with tmnxOamPmStsBaseTestType = 'dmm(1)', three rows are created in this table. The three rows have the following values in the tmnxOamPmCfgBinType index column: 'fd(1)', 'fdr(2)', and 'ifdv(3)'. Rows are destroyed in this table when the corresponding tmnxOamPmStsBaseTable row is destroyed. When a test is running, the DMM statistics for a test's raw (i.e. 'miRaw(1)') measurement interval duration can be cleared using TIMETRA-CLEAR-MIB::tmnxClearAction and tmnxClearParams. A successful clear operation zeros all the raw DMM statistics for the specified session.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmStsDelayDmmEntry  

tmnxOamPmStsDelayDmmFwdMin 1.3.6.1.4.1.6527.3.1.2.92.2.2.4.1.1
The value of tmnxOamPmStsDelayDmmFwdMin indicates the minimum delay in the forward direction for the specified session, interval duration (e.g. 'mi15Minutes(2)'), interval number, and bin type (e.g. 'fd(1)').
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayDmmFwdMax 1.3.6.1.4.1.6527.3.1.2.92.2.2.4.1.2
The value of tmnxOamPmStsDelayDmmFwdMax indicates the maximum delay in the forward direction for the specified session, interval duration (e.g. 'mi15Minutes(2)'), interval number, and bin type (e.g. 'fd(1)').
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayDmmFwdAvg 1.3.6.1.4.1.6527.3.1.2.92.2.2.4.1.3
The value of tmnxOamPmStsDelayDmmFwdAvg indicates the average delay in the forward direction for the specified session, interval duration (e.g. 'mi15Minutes(2)'), interval number, and bin type (e.g. 'fd(1)').
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayDmmBwdMin 1.3.6.1.4.1.6527.3.1.2.92.2.2.4.1.4
The value of tmnxOamPmStsDelayDmmBwdMin indicates the minimum delay in the backward direction for the specified session, interval duration (e.g. 'mi15Minutes(2)'), interval number, and bin type (e.g. 'fd(1)').
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayDmmBwdMax 1.3.6.1.4.1.6527.3.1.2.92.2.2.4.1.5
The value of tmnxOamPmStsDelayDmmBwdMax indicates the maximum delay in the backward direction for the specified session, interval duration (e.g. 'mi15Minutes(2)'), interval number, and bin type (e.g. 'fd(1)').
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayDmmBwdAvg 1.3.6.1.4.1.6527.3.1.2.92.2.2.4.1.6
The value of tmnxOamPmStsDelayDmmBwdAvg indicates the average delay in the backward direction for the specified session, interval duration (e.g. 'mi15Minutes(2)'), interval number, and bin type (e.g. 'fd(1)').
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayDmm2wyMin 1.3.6.1.4.1.6527.3.1.2.92.2.2.4.1.7
The value of tmnxOamPmStsDelayDmm2wyMin indicates the minimum two-way delay for the specified session, interval duration (e.g. 'mi15Minutes(2)'), interval number, and bin type (e.g. 'fd(1)').
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayDmm2wyMax 1.3.6.1.4.1.6527.3.1.2.92.2.2.4.1.8
The value of tmnxOamPmStsDelayDmm2wyMax indicates the maximum two-way delay for the specified session, interval duration (e.g. 'mi15Minutes(2)'), interval number, and bin type (e.g. 'fd(1)').
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayDmm2wyAvg 1.3.6.1.4.1.6527.3.1.2.92.2.2.4.1.9
The value of tmnxOamPmStsDelayDmm2wyAvg indicates the average two-way delay for the specified session, interval duration (e.g. 'mi15Minutes(2)'), interval number, and bin type (e.g. 'fd(1)').
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayDmmBinTable 1.3.6.1.4.1.6527.3.1.2.92.2.2.5
tmnxOamPmStsDelayDmmBinTable contains the per-bin DMM (Delay Measurement Message) statistics for OAM Performance Monitoring Measurement Interval Data Sets.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmStsDelayDmmBinEntry

tmnxOamPmStsDelayDmmBinEntry 1.3.6.1.4.1.6527.3.1.2.92.2.2.5.1
tmnxOamPmStsDelayDmmBinEntry contains the per-bin DMM (Delay Measurement Message) statistics for one OAM Performance Monitoring Measurement Interval Data Set. Rows are created in this table when a corresponding row is created in tmnxOamPmStsDelayDmmTable. If the tmnxOamPmStsDelayDmmTable row is created with the index value tmnxOamPmCfgBinType = 'fd(1)', then the the number of rows created in this table is tmnxOamPmCfgBinGroupFdBinCount. Similarly, 'fdr(2)' and 'ifdv(3)'. Rows are destroyed in this table when the corresponding tmnxOamPmStsDelayDmmTable row is destroyed. When a test is running, the DMM statistics for a test's raw (i.e. 'miRaw(1)') measurement interval duration can be cleared using TIMETRA-CLEAR-MIB::tmnxClearAction and tmnxClearParams. A successful clear operation zeros all the raw DMM statistics for the specified session.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmStsDelayDmmBinEntry  

tmnxOamPmStsDelayDmmBinNum 1.3.6.1.4.1.6527.3.1.2.92.2.2.5.1.1
The value of tmnxOamPmStsDelayDmmBinNum specifies the bin number of the statistics to be read.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..9  

tmnxOamPmStsDelayDmmBinFwdCount 1.3.6.1.4.1.6527.3.1.2.92.2.2.5.1.2
The value of tmnxOamPmStsDelayDmmBinFwdCount indicates the number of measurements in the forward direction that fall within the configured range (in microseconds) of the specified bin. For example, suppose the index values for this object are as follows (where the index names are abbreviated, and index columns are underlined with octothorpes). _SessName _IntvlDuration _IntvlNum _BinType _BinNum ########## ################ ######### ######## ####### 'dmmSess1' 'mi15Minutes(2)' 1 'fd(1)' 9 Then, the value of this object indicates the number of DMM measurements (in microseconds) in the forward direction in the first interval of 'dmmSess1' that fit in the highest configured delay range (as configured using tmnxOamPmCfgBinLowerBound).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayDmmBinBwdCount 1.3.6.1.4.1.6527.3.1.2.92.2.2.5.1.3
The value of tmnxOamPmStsDelayDmmBinBwdCount indicates the number of measurements in the backward direction that fall within the configured range (in microseconds) of the specified bin. For example, suppose the index values for this object are as follows (where the index names are abbreviated, and index columns are underlined with octothorpes). _SessName _IntvlDuration _IntvlNum _BinType _BinNum ########## ################ ######### ######## ####### 'dmmSess1' 'mi15Minutes(2)' 1 'fd(1)' 0 Then, the value of this object indicates the number of DMM measurements (in microseconds) in the backward direction in the first interval of 'dmmSess1' that fit in the lowest configured delay range (as configured using tmnxOamPmCfgBinLowerBound).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayDmmBin2wyCount 1.3.6.1.4.1.6527.3.1.2.92.2.2.5.1.4
The value of tmnxOamPmStsDelayDmmBin2wyCount indicates the number of two-way measurements that fall within the configured range (in microseconds) of the specified bin. For example, suppose the index values for this object are as follows (where the index names are abbreviated, and index columns are underlined with octothorpes). _SessName _IntvlDuration _IntvlNum _BinType _BinNum ########## ################ ######### ######## ####### 'dmmSess1' 'mi15Minutes(2)' 1 'fd(1)' 0 Then, the value of this object indicates the number of two-way DMM measurements (in microseconds) in the first interval of 'dmmSess1' that fit in the lowest configured delay range (as configured using tmnxOamPmCfgBinLowerBound).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsTwlRflTable 1.3.6.1.4.1.6527.3.1.2.92.2.2.6
tmnxOamPmStsTwlRflTable contains the statistics for OAM Performance Monitoring TWAMP-Light reflectors.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmStsTwlRflEntry

tmnxOamPmStsTwlRflEntry 1.3.6.1.4.1.6527.3.1.2.92.2.2.6.1
tmnxOamPmStsTwlRflEntry contains the statistics for the specified OAM Performance Monitoring TWAMP-Light reflector. SROS creates a row in this table when a corresponding row is created in tmnxOamPmCfgTwlRflTable. SROS destroys a row in this table when a corresponding row is destroyed in tmnxOamPmCfgTwlRflTable. The encoding of the index is explained in the DESCRIPTION clause for tmnxOamPmCfgTwlRflEntry.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmStsTwlRflEntry  

tmnxOamPmStsTwlRflUpTime 1.3.6.1.4.1.6527.3.1.2.92.2.2.6.1.1
The value of tmnxOamPmStsTwlRflUpTime indicates the time elapsed since the most recent transition of the reflector's administrative status to 'enabled(1)'. Zero is returned if the reflector's administrative status is 'disabled(2)'.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsTwlRflFramesRx 1.3.6.1.4.1.6527.3.1.2.92.2.2.6.1.2
The value of tmnxOamPmStsTwlRflFramesRx indicates the number of TWAMP-Test frames received by the specified reflector.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsTwlRflFramesTx 1.3.6.1.4.1.6527.3.1.2.92.2.2.6.1.3
The value of tmnxOamPmStsTwlRflFramesTx indicates the number of TWAMP-Test frames transmitted by the specified reflector.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayTwlTable 1.3.6.1.4.1.6527.3.1.2.92.2.2.7
tmnxOamPmStsDelayTwlTable contains TWAMP-Light (Two-Way Active Measurement Protocol, Light) frame delay summary statistics. The frame delay summary statistics kept for TWAMP-Light tests are the same as the frame delay summary statistics specified for Ethernet DMM (Delay Measurement Message) tests in MEF-35 requirement R66.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmStsDelayTwlEntry

tmnxOamPmStsDelayTwlEntry 1.3.6.1.4.1.6527.3.1.2.92.2.2.7.1
tmnxOamPmStsDelayTwlEntry contains the TWAMP-Light frame delay summary statistics for one OAM Performance Monitoring Measurement Interval Data Set. When a row is created in tmnxOamPmStsBaseTable with tmnxOamPmStsBaseTestType = 'twampLight(3)' (provided tmnxOamPmCfgTwampLtCollectStats is 'collectDelayStats(1)' or 'collectDelayAndLossStats(3)'), three rows are created in this table. The three rows have the following values in the tmnxOamPmCfgBinType index column: 'fd(1)', 'fdr(2)', and 'ifdv(3)'. Rows are destroyed in this table when the corresponding tmnxOamPmStsBaseTable row is destroyed. When a TWAMP-Light test is running, all the test's raw statistics can be cleared using TIMETRA-CLEAR-MIB::tmnxClearAction and tmnxClearParams. A successful clear operation zeros the TWAMP-Light delay and TWAMP-Light loss raw statistics for the specified session.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmStsDelayTwlEntry  

tmnxOamPmStsDelayTwlFwdMin 1.3.6.1.4.1.6527.3.1.2.92.2.2.7.1.1
The value of tmnxOamPmStsDelayTwlFwdMin indicates the minimum delay in the forward direction for the specified session, interval duration (e.g. 'mi15Minutes(2)'), interval number, and bin type (e.g. 'fd(1)').
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayTwlFwdMax 1.3.6.1.4.1.6527.3.1.2.92.2.2.7.1.2
The value of tmnxOamPmStsDelayTwlFwdMax indicates the maximum delay in the forward direction for the specified session, interval duration (e.g. 'mi15Minutes(2)'), interval number, and bin type (e.g. 'fd(1)').
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayTwlFwdAvg 1.3.6.1.4.1.6527.3.1.2.92.2.2.7.1.3
The value of tmnxOamPmStsDelayTwlFwdAvg indicates the average delay in the forward direction for the specified session, interval duration (e.g. 'mi15Minutes(2)'), interval number, and bin type (e.g. 'fd(1)').
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayTwlBwdMin 1.3.6.1.4.1.6527.3.1.2.92.2.2.7.1.4
The value of tmnxOamPmStsDelayTwlBwdMin indicates the minimum delay in the backward direction for the specified session, interval duration (e.g. 'mi15Minutes(2)'), interval number, and bin type (e.g. 'fd(1)').
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayTwlBwdMax 1.3.6.1.4.1.6527.3.1.2.92.2.2.7.1.5
The value of tmnxOamPmStsDelayTwlBwdMax indicates the maximum delay in the backward direction for the specified session, interval duration (e.g. 'mi15Minutes(2)'), interval number, and bin type (e.g. 'fd(1)').
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayTwlBwdAvg 1.3.6.1.4.1.6527.3.1.2.92.2.2.7.1.6
The value of tmnxOamPmStsDelayTwlBwdAvg indicates the average delay in the backward direction for the specified session, interval duration (e.g. 'mi15Minutes(2)'), interval number, and bin type (e.g. 'fd(1)').
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayTwl2wyMin 1.3.6.1.4.1.6527.3.1.2.92.2.2.7.1.7
The value of tmnxOamPmStsDelayTwl2wyMin indicates the minimum two-way delay for the specified session, interval duration (e.g. 'mi15Minutes(2)'), interval number, and bin type (e.g. 'fd(1)').
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayTwl2wyMax 1.3.6.1.4.1.6527.3.1.2.92.2.2.7.1.8
The value of tmnxOamPmStsDelayTwl2wyMax indicates the maximum two-way delay for the specified session, interval duration (e.g. 'mi15Minutes(2)'), interval number, and bin type (e.g. 'fd(1)').
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayTwl2wyAvg 1.3.6.1.4.1.6527.3.1.2.92.2.2.7.1.9
The value of tmnxOamPmStsDelayTwl2wyAvg indicates the average two-way delay for the specified session, interval duration (e.g. 'mi15Minutes(2)'), interval number, and bin type (e.g. 'fd(1)').
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayTwlBinTable 1.3.6.1.4.1.6527.3.1.2.92.2.2.8
tmnxOamPmStsDelayTwlBinTable contains TWAMP-Light (Two-Way Active Measurement Protocol, Light) frame delay per-bin statistics. The frame delay per-bin statistics kept for TWAMP-Light tests are the same as the frame delay per-bin statistics specified for Ethernet DMM (Delay Measurement Message) tests in MEF-35 requirement R66.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmStsDelayTwlBinEntry

tmnxOamPmStsDelayTwlBinEntry 1.3.6.1.4.1.6527.3.1.2.92.2.2.8.1
tmnxOamPmStsDelayTwlBinEntry contains the TWAMP-Light frame delay per-bin statistics for one OAM Performance Monitoring Measurement Interval Data Set. Rows are created in this table when a corresponding row is created in tmnxOamPmStsDelayTwlTable. If the tmnxOamPmStsDelayTwlTable row is created with the index value tmnxOamPmCfgBinType = 'fd(1)', then the the number of rows created in this table is tmnxOamPmCfgBinGroupFdBinCount. Similarly, 'fdr(2)' and 'ifdv(3)'. Rows are destroyed in this table when the corresponding tmnxOamPmStsDelayTwlTable row is destroyed. When a test is running, the TWAMP-Light statistics for a test's raw (i.e. 'miRaw(1)') measurement interval duration can be cleared using TIMETRA-CLEAR-MIB::tmnxClearAction and tmnxClearParams. A successful clear operation zeros the TWAMP-Light delay and TWAMP-Light loss raw statistics for the specified session..
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmStsDelayTwlBinEntry  

tmnxOamPmStsDelayTwlBinNum 1.3.6.1.4.1.6527.3.1.2.92.2.2.8.1.1
The value of tmnxOamPmStsDelayTwlBinNum specifies the bin number of the statistics to be read.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 0..9  

tmnxOamPmStsDelayTwlBinFwdCount 1.3.6.1.4.1.6527.3.1.2.92.2.2.8.1.2
The value of tmnxOamPmStsDelayTwlBinFwdCount indicates the number of TWAMP-Light frame delay measurements in the forward direction that fall within the configured range (in microseconds) of the specified bin. For example, suppose the index values for this object are as follows (where the index names are abbreviated, and index columns are underlined with octothorpes). _SessName _IntvlDuration _IntvlNum _BinType _BinNum ########## ################ ######### ######## ####### 'twlSess1' 'mi15Minutes(2)' 1 'fd(1)' 9 Then, the value of this object indicates the number of TWAMP-Light frame delay measurements (in microseconds) in the forward direction in the first interval of 'twlSess1' that fit in the highest configured delay range (as configured using tmnxOamPmCfgBinLowerBound).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayTwlBinBwdCount 1.3.6.1.4.1.6527.3.1.2.92.2.2.8.1.3
The value of tmnxOamPmStsDelayTwlBinBwdCount indicates the number of TWAMP-Light frame delay measurements in the backward direction that fall within the configured range (in microseconds) of the specified bin. For example, suppose the index values for this object are as follows (where the index names are abbreviated, and index columns are underlined with octothorpes). _SessName _IntvlDuration _IntvlNum _BinType _BinNum ########## ################ ######### ######## ####### 'twlSess1' 'mi15Minutes(2)' 1 'fd(1)' 0 Then, the value of this object indicates the number of TWAMP-Light frame delay measurements (in microseconds) in the backward direction in the first interval of 'twlSess1' that fit in the lowest configured delay range (as configured using tmnxOamPmCfgBinLowerBound).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsDelayTwlBin2wyCount 1.3.6.1.4.1.6527.3.1.2.92.2.2.8.1.4
The value of tmnxOamPmStsDelayTwlBin2wyCount indicates the number of TWAMP-Light two-way frame delay measurements that fall within the configured range (in microseconds) of the specified bin. For example, suppose the index values for this object are as follows (where the index names are abbreviated, and index columns are underlined with octothorpes). _SessName _IntvlDuration _IntvlNum _BinType _BinNum ########## ################ ######### ######## ####### 'twlSess1' 'mi15Minutes(2)' 1 'fd(1)' 0 Then, the value of this object indicates the number of TWAMP-Light two-way frame delay measurements (in microseconds) in the first interval of 'twlSess1' that fit in the lowest configured delay range (as configured using tmnxOamPmCfgBinLowerBound).
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmStsLossLmmTable 1.3.6.1.4.1.6527.3.1.2.92.2.2.9
tmnxOamPmStsLossLmmTable contains the frame loss statistics for OAM Performance Monitoring LMM (Loss Measurement Message) tests.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmStsLossLmmEntry

tmnxOamPmStsLossLmmEntry 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1
tmnxOamPmStsLossLmmEntry contains the LMM test statistics for one OAM Performance Monitoring Measurement Interval Data Set. A row is created in this table when a tmnxOamPmStsBaseTable row is created with tmnxOamPmStsBaseTestType = 'lmm(4)'. A row is destroyed in this table when the corresponding tmnxOamPmStsBaseTable row is destroyed. The following objects are modelled after the MEF-35 loss parameters defined for Synthetic Loss Measurement (SLM) tests: tmnxOamPmStsLossLmmAvailIndBwd, tmnxOamPmStsLossLmmAvailIndFwd, tmnxOamPmStsLossLmmChliBwd, tmnxOamPmStsLossLmmChliFwd, tmnxOamPmStsLossLmmHliBwd, tmnxOamPmStsLossLmmHliFwd, tmnxOamPmStsLossLmmUnavlIndBwd, and tmnxOamPmStsLossLmmUnavlIndFwd. Hence, the REFERENCE text for this object is a MEF-35 SLM section. The value of tmnxOamPmCfgLossLmmAvAdminStatus controls the value of several objects in this table. See the tmnxOamPmCfgLossLmmAvAdminStatus DESCRIPTION clause for more information. When a test is running, the LMM statistics for a test's raw (i.e. 'miRaw(1)') measurement interval duration can be cleared using TIMETRA-CLEAR-MIB::tmnxClearAction and tmnxClearParams. A successful clear operation zeros all raw LMM statistics for the specified session.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmStsLossLmmEntry  

tmnxOamPmStsLossLmmTxFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.1
The value of tmnxOamPmStsLossLmmTxFwd indicates the number of service frames transmitted in the forward direction for the specified measurement interval data set. This counter is computed using the procedures in Y.1731 Section 8.1.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

tmnxOamPmStsLossLmmRxFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.2
The value of tmnxOamPmStsLossLmmRxFwd indicates the number of service frames received in the forward direction for the specified measurement interval data set. This counter is computed using the procedures in Y.1731 Section 8.1.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

tmnxOamPmStsLossLmmTxBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.3
The value of tmnxOamPmStsLossLmmTxBwd indicates the number of service frames transmitted in the backward direction for the specified measurement interval data set. This counter is computed using the procedures in Y.1731 Section 8.1.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

tmnxOamPmStsLossLmmRxBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.4
The value of tmnxOamPmStsLossLmmRxBwd indicates the number of service frames received in the backward direction for the specified measurement interval data set. This counter is computed using the procedures in Y.1731 Section 8.1.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

tmnxOamPmStsLossLmmMinFlrFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.5
The value of tmnxOamPmStsLossLmmMinFlrFwd indicates the minimum Frame Loss Ratio (FLR) in the forward direction for the specified measurement interval data set. This value is computed using the procedures in Y.1731 Section 8.1.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

tmnxOamPmStsLossLmmMaxFlrFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.6
The value of tmnxOamPmStsLossLmmMaxFlrFwd indicates the maximum Frame Loss Ratio (FLR) in the forward direction for the specified measurement interval data set. This value is computed using the procedures in Y.1731 Section 8.1.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

tmnxOamPmStsLossLmmAvgFlrFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.7
The value of tmnxOamPmStsLossLmmAvgFlrFwd indicates the average Frame Loss Ratio (FLR) in the forward direction for the specified measurement interval data set. This value is computed using the procedures in Y.1731 Section 8.1.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

tmnxOamPmStsLossLmmMinFlrBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.8
The value of tmnxOamPmStsLossLmmMinFlrBwd indicates the minimum Frame Loss Ratio (FLR) in the backward direction for the specified measurement interval data set. This value is computed using the procedures in Y.1731 Section 8.1.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

tmnxOamPmStsLossLmmMaxFlrBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.9
The value of tmnxOamPmStsLossLmmMaxFlrBwd indicates the maximum Frame Loss Ratio (FLR) in the backward direction for the specified measurement interval data set. This value is computed using the procedures in Y.1731 Section 8.1.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

tmnxOamPmStsLossLmmAvgFlrBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.10
The value of tmnxOamPmStsLossLmmAvgFlrBwd indicates the average Frame Loss Ratio (FLR) in the backward direction for the specified measurement interval data set. This value is computed using the procedures in Y.1731 Section 8.1.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

tmnxOamPmStsLossLmmAvailIndFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.11
The value of tmnxOamPmStsLossLmmAvailIndFwd indicates the number of availability indicators evaluated as Available in the forward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossLmmAvailIndBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.12
The value of tmnxOamPmStsLossLmmAvailIndBwd indicates the number of availability indicators evaluated as Available in the backward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossLmmUnavlIndFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.13
The value of tmnxOamPmStsLossLmmUnavlIndFwd indicates the number of availability indicators evaluated as Unavailable in the forward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossLmmUnavlIndBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.14
The value of tmnxOamPmStsLossLmmUnavlIndBwd indicates the number of availability indicators evaluated as Unavailable in the backward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossLmmUndtAvlFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.15
The value of tmnxOamPmStsLossLmmUndtAvlFwd indicates the number of availability indicators evaluated as Undetermined Available, in the forward direction. This counter is incremented when: 1. It is time to calculate an availability indicator, and 2. No Loss Measurement Replies (LMRs) have been received within the availability window, and 3. The most recently declared availability indicator in the forward direction was Available. In that case, the availability indicator is Undetermined Available because: 1. No information is available to indicate if the problem is in the forward direction or the backward direction, and 2. We extrapolate from the previous state (i.e. Available).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossLmmUndtUnavlFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.16
The value of tmnxOamPmStsLossLmmUndtUnavlFwd indicates the number of availability indicators evaluated as Undetermined Unavailable, in the forward direction. This counter is incremented when: 1. It is time to calculate an availability indicator, and 2. No Loss Measurement Replies (LMRs) have been received within the availability window, and 3. The most recently declared availability indicator in the forward direction was Unavailable. In that case, the availability indicator is Undetermined Unavailable because: 1. No information is available to indicate if the problem is in the forward direction or the backward direction, and 2. We extrapolate from the previous state (i.e. Unavailable).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossLmmUndtAvlBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.17
The value of tmnxOamPmStsLossLmmUndtAvlBwd indicates the number of availability indicators evaluated as Undetermined Available, in the backward direction. This counter is incremented when: 1. It is time to calculate an availability indicator, and 2. No Loss Measurement Replies (LMRs) have been received within the availability window, and 3. The most recently declared availability indicator in the backward direction was Available. In that case, the availability indicator is Undetermined Available because: 1. No information is available to indicate if the problem is in the forward direction or the backward direction, and 2. We extrapolate from the previous state (i.e. Available).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossLmmUndtUnavlBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.18
The value of tmnxOamPmStsLossLmmUndtUnavlBwd indicates the number of availability indicators evaluated as Undetermined Unavailable, in the backward direction. This counter is incremented when: 1. It is time to calculate an availability indicator, and 2. No Loss Measurement Replies (LMRs) have been received within the availability window, and 3. The most recently declared availability indicator in the backward direction was Unavailable. In that case, the availability indicator is Undetermined Unavailable because: 1. No information is available to indicate if the problem is in the forward direction or the backward direction, and 2. We extrapolate from the previous state (i.e. Unavailable).
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossLmmHliFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.19
The value of tmnxOamPmStsLossLmmHliFwd indicates the number of High Loss Intervals (HLIs) in the forward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossLmmHliBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.20
The value of tmnxOamPmStsLossLmmHliBwd indicates the number of High Loss Intervals (HLIs) in the backward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossLmmChliFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.21
The value of tmnxOamPmStsLossLmmChliFwd indicates the number of Consecutive High Loss Intervals (CHLIs) in the forward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossLmmChliBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.22
The value of tmnxOamPmStsLossLmmChliBwd indicates the number of Consecutive High Loss Intervals (CHLIs) in the backward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossLmmUndetDelTsFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.23
The value of tmnxOamPmStsLossLmmUndetDelTsFwd indicates the number of undetermined MEF-35 'delta_t's (also known as 'Small Time Intervals') for the forward direction for the specified measurement interval data set. An undetermined delta_t occurs when no Loss Measurement Reply (LMR) PDUs are received during the time interval. This counter is incremented because of a problem with the data path, or because the MEF-35 delta_t for this test is too short. delta_t is configured using tmnxOamPmCfgLossLmmInterval and tmnxOamPmCfgLossLmmTxFrmsPerDelT.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossLmmUndetDelTsBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.9.1.24
The value of tmnxOamPmStsLossLmmUndetDelTsBwd indicates the number of undetermined MEF-35 'delta_t's (also known as 'Small Time Intervals') for the backward direction for the specified measurement interval data set. An undetermined delta_t occurs when no Loss Measurement Reply (LMR) PDUs are received during the time interval. This counter is incremented because of a problem with the data path, or because the MEF-35 delta_t for this test is too short. delta_t is configured using tmnxOamPmCfgLossLmmInterval and tmnxOamPmCfgLossLmmTxFrmsPerDelT.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossTwlTable 1.3.6.1.4.1.6527.3.1.2.92.2.2.10
tmnxOamPmStsLossTwlTable contains TWAMP-Light (Two-Way Active Measurement Protocol, Light) frame loss statistics. The frame loss statistics kept for TWAMP-Light tests are the same as the frame loss statistics specified for Ethernet SLM (Synthetic Loss Measurement) tests in MEF-35 section 10.2.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmStsLossTwlEntry

tmnxOamPmStsLossTwlEntry 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1
tmnxOamPmStsLossTwlEntry contains the TWAMP-Light loss test statistics for one OAM Performance Monitoring Measurement Interval Data Set. A row is created in this table when a tmnxOamPmStsBaseTable row is created with tmnxOamPmStsBaseTestType = 'twampLight(3)' (provided tmnxOamPmCfgTwampLtCollectStats is 'collectLossStats(2)' or 'collectDelayAndLossStats(3)'). A row is destroyed in this table when the corresponding tmnxOamPmStsBaseTable row is destroyed. When a TWAMP-Light test is running, all the test's raw statistics can be cleared using TIMETRA-CLEAR-MIB::tmnxClearAction and tmnxClearParams. A successful clear operation zeros the TWAMP-Light delay and TWAMP-Light loss raw statistics for the specified session.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmStsLossTwlEntry  

tmnxOamPmStsLossTwlTxFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.1
The value of tmnxOamPmStsLossTwlTxFwd indicates the number of TWAMP-Light request frames transmitted in the forward direction for the specified measurement interval data set. A frame is counted if the TWAMP-Light Availability state is Available at transmit time (as specified in MEF-35 Section 9.2.5). A simple count of the frames transmitted for the test is available in tmnxOamPmStsBaseTestFramesTx.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossTwlRxFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.2
The value of tmnxOamPmStsLossTwlRxFwd indicates the number of TWAMP-Light request frames received in the forward direction for the specified measurement interval data set. A frame is counted if the TWAMP-Light Availability state is Available at receive time (as specified in MEF-35 Section 9.2.5). A simple count of the frames received for the test is available in tmnxOamPmStsBaseTestFramesRx.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossTwlTxBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.3
The value of tmnxOamPmStsLossTwlTxBwd indicates the number of TWAMP-Light reply frames transmitted in the backward direction for the specified measurement interval data set. A frame is counted if the TWAMP-Light Availability state is Available at transmit time (as specified in MEF-35 Section 9.2.5). A simple count of the frames transmitted for the test is available in tmnxOamPmStsBaseTestFramesTx.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossTwlRxBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.4
The value of tmnxOamPmStsLossTwlRxBwd indicates the number of TWAMP-Light reply frames received in the backward direction for the specified measurement interval data set. A frame is counted if the TWAMP-Light Availability state is Available at receive time (as specified in MEF-35 Section 9.2.5). A simple count of the frames received for the test is available in tmnxOamPmStsBaseTestFramesRx.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossTwlAvailIndFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.5
The value of tmnxOamPmStsLossTwlAvailIndFwd indicates the number of availability indicators evaluated as Available in the forward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossTwlAvailIndBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.6
The value of tmnxOamPmStsLossTwlAvailIndBwd indicates the number of availability indicators evaluated as Available in the backward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossTwlUnavlIndFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.7
The value of tmnxOamPmStsLossTwlUnavlIndFwd indicates the number of availability indicators evaluated as Unavailable in the forward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossTwlUnavlIndBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.8
The value of tmnxOamPmStsLossTwlUnavlIndBwd indicates the number of availability indicators evaluated as Unavailable in the backward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossTwlUndtAvlFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.9
The value of tmnxOamPmStsLossTwlUndtAvlFwd indicates the number of availability indicators evaluated as Available in the forward direction, based on extrapolation from the previous state. For example, this counter will be incremented when: 1. It is time to calculate an availability indicator, and 2. All the probe requests used to calculate the availability indicator have timed out, and 3. The most recently declared availability indicator in the forward direction was Available. In that case, the result is considered undetermined because no information is available to indicate if the problem is in the forward direction or the backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossTwlUndtUnavlFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.10
The value of tmnxOamPmStsLossTwlUndtUnavlFwd indicates the number of availability indicators evaluated as Unavailable in the forward direction, based on extrapolation from the previous state. For example, this counter will be incremented when: 1. It is time to calculate an availability indicator, and 2. All the probe requests used to calculate the availability indicator have timed out, and 3. The most recently declared availability indicator in the forward direction was Unavailable. In that case, the result is considered undetermined because no information is available to indicate if the problem is in the forward direction or the backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossTwlUndtAvlBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.11
The value of tmnxOamPmStsLossTwlUndtAvlBwd indicates the number of availability indicators evaluated as Available in the backward direction, based on extrapolation from the previous state. For example, this counter will be incremented when: 1. It is time to calculate an availability indicator, and 2. All the probe requests used to calculate the availability indicator have timed out, and 3. The most recently declared availability indicator in the backward direction was Available. In that case, the result is considered undetermined because no information is available to indicate if the problem is in the forward direction or the backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossTwlUndtUnavlBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.12
The value of tmnxOamPmStsLossTwlUndtUnavlBwd indicates the number of availability indicators evaluated as Unavailable in the backward direction, based on extrapolation from the previous state. For example, this counter will be incremented when: 1. It is time to calculate an availability indicator, and 2. All the probe requests used to calculate the availability indicator have timed out, and 3. The most recently declared availability indicator in the backward direction was Unavailable. In that case, the result is considered undetermined because no information is available to indicate if the problem is in the forward direction or the backward direction.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossTwlHliFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.13
The value of tmnxOamPmStsLossTwlHliFwd indicates the number of High Loss Intervals (HLIs) in the forward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossTwlHliBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.14
The value of tmnxOamPmStsLossTwlHliBwd indicates the number of High Loss Intervals (HLIs) in the backward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossTwlChliFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.15
The value of tmnxOamPmStsLossTwlChliFwd indicates the number of Consecutive High Loss Intervals (CHLIs) in the forward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossTwlChliBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.16
The value of tmnxOamPmStsLossTwlChliBwd indicates the number of Consecutive High Loss Intervals (CHLIs) in the backward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxOamPmStsLossTwlMinFlrFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.17
The value of tmnxOamPmStsLossTwlMinFlrFwd indicates the minimum Frame Loss Ratio (FLR) in the forward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

tmnxOamPmStsLossTwlMaxFlrFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.18
The value of tmnxOamPmStsLossTwlMaxFlrFwd indicates the maximum Frame Loss Ratio (FLR) in the forward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

tmnxOamPmStsLossTwlAvgFlrFwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.19
The value of tmnxOamPmStsLossTwlAvgFlrFwd indicates the average Frame Loss Ratio (FLR) in the forward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

tmnxOamPmStsLossTwlMinFlrBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.20
The value of tmnxOamPmStsLossTwlMinFlrBwd indicates the minimum Frame Loss Ratio (FLR) in the backward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

tmnxOamPmStsLossTwlMaxFlrBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.21
The value of tmnxOamPmStsLossTwlMaxFlrBwd indicates the maximum Frame Loss Ratio (FLR) in the backward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

tmnxOamPmStsLossTwlAvgFlrBwd 1.3.6.1.4.1.6527.3.1.2.92.2.2.10.1.22
The value of tmnxOamPmStsLossTwlAvgFlrBwd indicates the average Frame Loss Ratio (FLR) in the backward direction for the specified measurement interval data set.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 0..100000  

tmnxOamPmStsTcaDelayTable 1.3.6.1.4.1.6527.3.1.2.92.2.2.11
tmnxOamPmStsTcaDelayTable contains statistics for delay-based OAM-PM Threshold Crossing Alerts (TCAs).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmStsTcaDelayEntry

tmnxOamPmStsTcaDelayEntry 1.3.6.1.4.1.6527.3.1.2.92.2.2.11.1
tmnxOamPmStsTcaDelayEntry contains the OAM-PM delay TCA statistics for the combination of an OAM-PM session name, test type, bin type, and direction (e.g. {'oam_pm_sess_1', 'dmm(1)', 'ifdv(3)', 'twoWay(3)'}). Nine rows are created/destroyed in this table when a delay test is created/destroyed. A delay test is created/destroyed using tmnxOamPmCfgDelayDmmRowStatus or tmnxOamPmCfgTwampLtRowStatus. The nine rows are indexed by the session name, the test type, and the nine combinations of bin type and direction.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmStsTcaDelayEntry  

tmnxOamPmStsTcaDelayLastTime 1.3.6.1.4.1.6527.3.1.2.92.2.2.11.1.1
The value of tmnxOamPmStsTcaDelayLastTime indicates the UTC date and time at the start of the measurement interval which generated the most recent delay-based Raise or Clear TCA for the specified indices. Measurement interval start times are reported using tmnxOamPmStsBaseStartTime. The TCAs are tmnxOamPmThrRaise and tmnxOamPmThrClear. DateAndTime.year = 0 is returned if no TCAs have been generated for the specified indices since system start up.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime Size(8)  

tmnxOamPmStsTcaDelayOperState 1.3.6.1.4.1.6527.3.1.2.92.2.2.11.1.2
The value of tmnxOamPmStsTcaDelayOperState indicates the operational state of delay-based TCAs for the specified indices.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxOamPmStsTcaOperState  

tmnxOamPmStsTcaLossFwBwAgTable 1.3.6.1.4.1.6527.3.1.2.92.2.2.12
tmnxOamPmStsTcaLossFwBwAgTable contains statistics for loss-based OAM-PM Threshold Crossing Alerts (TCAs). The subset of the TCA loss statistics that are kept in the forward, backward, and aggregate directions is available using this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmStsTcaLossFwBwAgEntry

tmnxOamPmStsTcaLossFwBwAgEntry 1.3.6.1.4.1.6527.3.1.2.92.2.2.12.1
tmnxOamPmStsTcaLossFwBwAgEntry contains the TCA statistics for the forward, backward, or aggregate direction of one OAM-PM loss test. For example, a row may contain TCA statistics for the forward direction for the SLM test belonging to OAM-PM session OAM_PM_Eth_session_1.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmStsTcaLossFwBwAgEntry  

tmnxOamPmStsTcaLossChliLastTime 1.3.6.1.4.1.6527.3.1.2.92.2.2.12.1.1
The value of tmnxOamPmStsTcaLossChliLastTime indicates the UTC date and time at the start of the measurement interval which generated the most recent Consecutive High Loss Interval (CHLI) Raise or Clear TCA for the specified indices. Measurement interval start times are reported using tmnxOamPmStsBaseStartTime. The TCAs are tmnxOamPmThrRaise and tmnxOamPmThrClear. DateAndTime.year = 0 is returned if no CHLI TCAs have been generated for the specified indices since system start up.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime Size(8)  

tmnxOamPmStsTcaLossChliOperState 1.3.6.1.4.1.6527.3.1.2.92.2.2.12.1.2
The value of tmnxOamPmStsTcaLossChliOperState indicates the operational state of Consecutive High Loss Interval (CHLI) TCAs for the specified indices.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxOamPmStsTcaOperState  

tmnxOamPmStsTcaLossHliLastTime 1.3.6.1.4.1.6527.3.1.2.92.2.2.12.1.3
The value of tmnxOamPmStsTcaLossHliLastTime indicates the UTC date and time at the start of the measurement interval which generated the most recent High Loss Interval (HLI) Raise or Clear TCA for the specified indices. Measurement interval start times are reported using tmnxOamPmStsBaseStartTime. The TCAs are tmnxOamPmThrRaise and tmnxOamPmThrClear. DateAndTime.year = 0 is returned if no HLI TCAs have been generated for the specified indices since system start up.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime Size(8)  

tmnxOamPmStsTcaLossHliOperState 1.3.6.1.4.1.6527.3.1.2.92.2.2.12.1.4
The value of tmnxOamPmStsTcaLossHliOperState indicates the operational state of High Loss Interval (HLI) TCAs for the specified indices.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxOamPmStsTcaOperState  

tmnxOamPmStsTcaLossUnavlIndLTime 1.3.6.1.4.1.6527.3.1.2.92.2.2.12.1.5
The value of tmnxOamPmStsTcaLossUnavlIndLTime indicates the UTC date and time at the start of the measurement interval which generated the most recent Unavailability Indicator Raise or Clear TCA for the specified indices. Measurement interval start times are reported using tmnxOamPmStsBaseStartTime. The TCAs are tmnxOamPmThrRaise and tmnxOamPmThrClear. DateAndTime.year = 0 is returned if no Unavailability Indicator TCAs have been generated for the specified indices since system start up.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime Size(8)  

tmnxOamPmStsTcaLossUnavlIndOprSt 1.3.6.1.4.1.6527.3.1.2.92.2.2.12.1.6
The value of tmnxOamPmStsTcaLossUnavlIndOprSt indicates the operational state of Unavailability Indicator TCAs for the specified indices.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxOamPmStsTcaOperState  

tmnxOamPmStsTcaLossUndtAvlLTime 1.3.6.1.4.1.6527.3.1.2.92.2.2.12.1.7
The value of tmnxOamPmStsTcaLossUndtAvlLTime indicates the UTC date and time at the start of the measurement interval which generated the most recent Undetermined Availability Indicator Raise or Clear TCA for the specified indices. Measurement interval start times are reported using tmnxOamPmStsBaseStartTime. The TCAs are tmnxOamPmThrRaise and tmnxOamPmThrClear. DateAndTime.year = 0 is returned if no Undetermined Availability Indicator TCAs have been generated for the specified indices since system start up.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime Size(8)  

tmnxOamPmStsTcaLossUndtAvlOperSt 1.3.6.1.4.1.6527.3.1.2.92.2.2.12.1.8
The value of tmnxOamPmStsTcaLossUndtAvlOperSt indicates the operational state of Undetermined Availability Indicator TCAs for the specified indices.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxOamPmStsTcaOperState  

tmnxOamPmStsTcaLossUndtUnavlLTim 1.3.6.1.4.1.6527.3.1.2.92.2.2.12.1.9
The value of tmnxOamPmStsTcaLossUndtUnavlLTim indicates the UTC date and time at the start of the measurement interval which generated the most recent Undetermined Unavailability Indicator Raise or Clear TCA for the specified indices. Measurement interval start times are reported using tmnxOamPmStsBaseStartTime. The TCAs are tmnxOamPmThrRaise and tmnxOamPmThrClear. DateAndTime.year = 0 is returned if no Undetermined Unavailability Indicator TCAs have been generated for the specified indices since system start up.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime Size(8)  

tmnxOamPmStsTcaLossUndtUnavlOpSt 1.3.6.1.4.1.6527.3.1.2.92.2.2.12.1.10
The value of tmnxOamPmStsTcaLossUndtUnavlOpSt indicates the operational state of Undetermined Unavailability Indicator TCAs for the specified indices.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxOamPmStsTcaOperState  

tmnxOamPmStsTcaLossFwBwTable 1.3.6.1.4.1.6527.3.1.2.92.2.2.13
tmnxOamPmStsTcaLossFwBwTable contains statistics for loss-based OAM-PM Threshold Crossing Alerts (TCAs). The subset of the TCA loss statistics that are kept in the forward and backward directions is available using this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmStsTcaLossFwBwEntry

tmnxOamPmStsTcaLossFwBwEntry 1.3.6.1.4.1.6527.3.1.2.92.2.2.13.1
tmnxOamPmStsTcaLossFwBwEntry contains TCA statistics for the forward or backward direction of one OAM-PM loss test. For example, a row may contain TCA statistics for the forward direction for the SLM test belonging to OAM-PM session OAM_PM_Eth_session_1.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmStsTcaLossFwBwEntry  

tmnxOamPmStsTcaLossAvgFlrLstTime 1.3.6.1.4.1.6527.3.1.2.92.2.2.13.1.1
The value of tmnxOamPmStsTcaLossAvgFlrLstTime indicates the UTC date and time at the start of the measurement interval which generated the most recent Average Frame Loss Ratio (FLR) Raise or Clear TCA for the specified indices. Measurement interval start times are reported using tmnxOamPmStsBaseStartTime. The TCAs are tmnxOamPmThrRaise and tmnxOamPmThrClear. DateAndTime.year = 0 is returned if no Average FLR TCAs have been generated for the specified indices since system start up.
Status: current Access: read-only
OBJECT-TYPE    
  DateAndTime Size(8)  

tmnxOamPmStsTcaLossAvgFlrOperSt 1.3.6.1.4.1.6527.3.1.2.92.2.2.13.1.2
The value of tmnxOamPmStsTcaLossAvgFlrOperSt indicates the operational state of Average Frame Loss Ratio (FLR) TCAs for the specified indices.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxOamPmStsTcaOperState  

tmnxOamPmStsSessIpTable 1.3.6.1.4.1.6527.3.1.2.92.2.2.14
tmnxOamPmStsSessIpTable contains status information for OAM-PM sessions with tmnxOamPmCfgSessTestFamily equal to 'ip(2)'.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmStsSessIpEntry

tmnxOamPmStsSessIpEntry 1.3.6.1.4.1.6527.3.1.2.92.2.2.14.1
tmnxOamPmStsSessIpEntry contains status information for an OAM-PM session with tmnxOamPmCfgSessTestFamily equal to 'ip(2)'.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmStsSessIpEntry  

tmnxOamPmStsSessIpSrcUdpPort 1.3.6.1.4.1.6527.3.1.2.92.2.2.14.1.1
The value of tmnxOamPmStsSessIpSrcUdpPort indicates the source UDP port allocated for the specified OAM-PM IP session. The allocation of source UDP ports is described in the DESCRIPTION clause of tmnxOamPmCfgSessIpSrcUdpPort. If the source UDP port has not been successfully allocated (or has been deallocated), tmnxOamPmStsSessIpSrcUdpPort is zero.
Status: current Access: read-only
OBJECT-TYPE    
  InetPortNumber  

tmnxOamPmStsTestTable 1.3.6.1.4.1.6527.3.1.2.92.2.2.15
tmnxOamPmStsTestTable contains status information for OAM-PM tests. Additional test status information is available in tmnxOamPmCfgDelayDmmTable, tmnxOamPmCfgLossLmmTable, tmnxOamPmCfgLossSlmTable, and tmnxOamPmCfgTwampLtTable.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxOamPmStsTestEntry

tmnxOamPmStsTestEntry 1.3.6.1.4.1.6527.3.1.2.92.2.2.15.1
tmnxOamPmStsTestEntry contains status information for the OAM-PM test specified by the indices. A row is created/destroyed in this table when an OAM-PM test is created/destroyed. An OAM-PM test is created/destroyed using tmnxOamPmCfgDelayDmmRowStatus, tmnxOamPmCfgLossLmmRowStatus, tmnxOamPmCfgLossSlmRowStatus, or tmnxOamPmCfgTwampLtRowStatus.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxOamPmStsTestEntry  

tmnxOamPmStsTestDetectTxError 1.3.6.1.4.1.6527.3.1.2.92.2.2.15.1.1
The value of tmnxOamPmStsTestDetectTxError indicates a reason for the specified test's current inability (if any) to launch request frames. For example, 'ethParentAdminDown(4)' could be returned for an SLM test if the MEP to be tested is associated with a SAP which is administratively down. Not all request frame transmit failures are detected by this mechanism. It is possible that 'none(1)' will be returned when the test is unable to transmit frames.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxOamPmDetectableTxError  

tmnxOamPmNotifThrType 1.3.6.1.4.1.6527.3.1.2.92.3.1
The value of tmnxOamPmNotifThrType indicates the type of the OAM-PM threshold crossing being reported. The code points are as follows. delay (1) - a threshold (e.g.tmnxOamPmCfgThrDelayRaise) on a MEF-35 delay count has been crossed lossAvgFlr (2) - a threshold (e.g. tmnxOamPmCfgThrLossAvgFlrClear) on a MEF-35 Average Frame Loss Ratio (FLR) has been crossed lossChli (3) - a threshold (e.g. tmnxOamPmCfgThrLossChliRaise) on a MEF-35 Consecutive High Loss Interval (CHLI) count has been crossed lossHlii (4) - a threshold (e.g. tmnxOamPmCfgThrLossHliClear) on a MEF-35 High Loss Interval (HLI) count has been crossed lossUnavail (5) - a threshold (e.g. tmnxOamPmCfgThrLossUnavlIndRaise) on a MEF-35 Unavailability Indicator count has been crossed lossUndetAvail (6) - a threshold (e.g. tmnxOamPmCfgThrLossUndtAvlClear) on an Undetermined Availability Indicator count has been crossed lossUndetUnavail(7) - a threshold (e.g. tmnxOamPmCfgThrLossUndtUnavlRais) on an Undetermined Unavailability Indicator count has been crossed
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER delay(1), lossAvgFlr(2), lossChli(3), lossHli(4), lossUnavail(5), lossUndetAvail(6), lossUndetUnavail(7)  

tmnxOamPmNotifThrDirection 1.3.6.1.4.1.6527.3.1.2.92.3.2
The value of tmnxOamPmNotifThrDirection indicates the traffic flow direction of the OAM-PM threshold crossing being reported. The semantics of the code points are documented in the DESCRIPTION clauses of TmnxOamPmForwardBackwardAggr and TmnxOamPmForwardBackwardTwoWay.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER forward(1), backward(2), twoWay(3), aggregate(4)  

tmnxOamPmNotifThrDelayBinType 1.3.6.1.4.1.6527.3.1.2.92.3.3
The value of tmnxOamPmNotifThrDelayBinType indicates the bin type of the OAM-PM delay threshold crossing being reported. 'notApplicable(0)' is used for loss tests (i.e. when tmnxOamPmNotifThrType is not 'delay(1)'). The semantics of the other code points are documented in the DESCRIPTION clause of TmnxOamPmBinType.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER notApplicable(0), fd(1), fdr(2), ifdv(3)  

tmnxOamPmNotifThrStateType 1.3.6.1.4.1.6527.3.1.2.92.3.4
The value of tmnxOamPmNotifThrStateType indicates whether or not the OAM-PM threshold crossing being reported is stateful. The code points are as follows. stateful (1) - a clearing threshold is defined for the condition. stateless(2) - a clearing threshold is not defined for the condition. The DESCRIPTION clause of tmnxOamPmCfgThrLossChliClear explains the change in behavior when a clearing threshold is defined.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  INTEGER stateful(1), stateless(2)  

tmnxOamPmNotifThrCfgRaise 1.3.6.1.4.1.6527.3.1.2.92.3.5
The value of tmnxOamPmNotifThrCfgRaise indicates the configured raise threshold for the OAM-PM Raise trap being reported. The value reported is one of the following (where the selection is made by other objects in the trap): tmnxOamPmCfgThrDelayRaise, tmnxOamPmCfgThrLossAvgFlrRaise, tmnxOamPmCfgThrLossChliRaise, tmnxOamPmCfgThrLossHliRaise, tmnxOamPmCfgThrLossUnavlIndRaise, tmnxOamPmCfgThrLossUndtAvlRaise, or tmnxOamPmCfgThrLossUndtUnavlRais.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmNotifThrCfgClear 1.3.6.1.4.1.6527.3.1.2.92.3.6
The value of tmnxOamPmNotifThrCfgClear indicates the configured clear threshold for the OAM-PM Clear trap being reported. The value reported is one of the following (where the selection is made by other objects in the trap): tmnxOamPmCfgThrDelayClear, tmnxOamPmCfgThrLossAvgFlrClear, tmnxOamPmCfgThrLossChliClear, tmnxOamPmCfgThrLossHliClear, tmnxOamPmCfgThrLossUnavlIndClear, tmnxOamPmCfgThrLossUndtAvlClear, or tmnxOamPmCfgThrLossUndtUnavlClr.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmNotifThrOperRaise 1.3.6.1.4.1.6527.3.1.2.92.3.7
The value of tmnxOamPmNotifThrOperRaise indicates the value of the delay or loss counter which met or exceeded tmnxOamPmNotifThrCfgRaise, resulting in the OAM-PM Raise trap being reported. The value reported is one of the following (where the selection is made by other objects in the trap): tmnxOamPmStsDelayDmmBin2wyCount, tmnxOamPmStsDelayDmmBinBwdCount, tmnxOamPmStsDelayDmmBinFwdCount, tmnxOamPmStsDelayTwlBin2wyCount, tmnxOamPmStsDelayTwlBinBwdCount, tmnxOamPmStsDelayTwlBinFwdCount, tmnxOamPmStsLossLmmAvgFlrBwd, tmnxOamPmStsLossLmmAvgFlrFwd, tmnxOamPmStsLossLmmChliBwd, tmnxOamPmStsLossLmmChliFwd + tmnxOamPmStsLossLmmChliBwd, tmnxOamPmStsLossLmmChliFwd, tmnxOamPmStsLossLmmHliBwd, tmnxOamPmStsLossLmmHliFwd + tmnxOamPmStsLossLmmHliBwd, tmnxOamPmStsLossLmmHliFwd, tmnxOamPmStsLossLmmUnavlIndBwd, tmnxOamPmStsLossLmmUnavlIndFwd + tmnxOamPmStsLossLmmUnavlIndBwd, tmnxOamPmStsLossLmmUnavlIndFwd, tmnxOamPmStsLossLmmUndtAvlBwd, tmnxOamPmStsLossLmmUndtAvlFwd + tmnxOamPmStsLossLmmUndtAvlBwd, tmnxOamPmStsLossLmmUndtAvlFwd, tmnxOamPmStsLossLmmUndtUnavlBwd, tmnxOamPmStsLossLmmUndtUnavlFwd + tmnxOamPmStsLossLmmUndtUnavlBwd, tmnxOamPmStsLossLmmUndtUnavlFwd, tmnxOamPmStsLossSlmAvgFlrBwd, tmnxOamPmStsLossSlmAvgFlrFwd, tmnxOamPmStsLossSlmChliBwd, tmnxOamPmStsLossSlmChliFwd + tmnxOamPmStsLossSlmChliBwd, tmnxOamPmStsLossSlmChliFwd, tmnxOamPmStsLossSlmHliBwd, tmnxOamPmStsLossSlmHliFwd + tmnxOamPmStsLossSlmHliBwd, tmnxOamPmStsLossSlmHliFwd, tmnxOamPmStsLossSlmUnavlIndBwd, tmnxOamPmStsLossSlmUnavlIndFwd + tmnxOamPmStsLossSlmUnavlIndBwd, tmnxOamPmStsLossSlmUnavlIndFwd, tmnxOamPmStsLossSlmUndtAvlBwd, tmnxOamPmStsLossSlmUndtAvlFwd + tmnxOamPmStsLossSlmUndtAvlBwd, tmnxOamPmStsLossSlmUndtAvlFwd, tmnxOamPmStsLossSlmUndtUnavlBwd, tmnxOamPmStsLossSlmUndtUnavlFwd + tmnxOamPmStsLossSlmUndtUnavlBwd, tmnxOamPmStsLossSlmUndtUnavlFwd, tmnxOamPmStsLossTwlAvgFlrBwd, tmnxOamPmStsLossTwlAvgFlrFwd, tmnxOamPmStsLossTwlChliBwd, tmnxOamPmStsLossTwlChliFwd + tmnxOamPmStsLossTwlChliBwd, tmnxOamPmStsLossTwlChliFwd, tmnxOamPmStsLossTwlHliBwd, tmnxOamPmStsLossTwlHliFwd + tmnxOamPmStsLossTwlHliBwd, tmnxOamPmStsLossTwlHliFwd, tmnxOamPmStsLossTwlUnavlIndBwd, tmnxOamPmStsLossTwlUnavlIndFwd + tmnxOamPmStsLossTwlUnavlIndBwd, tmnxOamPmStsLossTwlUnavlIndFwd, tmnxOamPmStsLossTwlUndtAvlBwd, tmnxOamPmStsLossTwlUndtAvlFwd + tmnxOamPmStsLossTwlUndtAvlBwd, tmnxOamPmStsLossTwlUndtAvlFwd, tmnxOamPmStsLossTwlUndtUnavlBwd, tmnxOamPmStsLossTwlUndtUnavlFwd + tmnxOamPmStsLossTwlUndtUnavlBwd, or tmnxOamPmStsLossTwlUndtUnavlFwd. One of the '2wy' values is reported when tmnxOamPmNotifThrDirection is 'twoWay(3)'. One of the summed values is reported when tmnxOamPmNotifThrDirection is 'aggregate(4)'.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmNotifThrOperClear 1.3.6.1.4.1.6527.3.1.2.92.3.8
The value of tmnxOamPmNotifThrOperClear indicates the value of the delay or loss counter which met or fell below tmnxOamPmNotifThrCfgClear, resulting in the OAM-PM Clear trap being reported. The value reported is one of the values shown in the tmnxOamPmNotifThrOperRaise DESCRIPTION clause.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmNotifThrBinLowerBound 1.3.6.1.4.1.6527.3.1.2.92.3.9
The value of tmnxOamPmNotifThrBinLowerBound indicates the configured lower bound (in microseconds) of the MEF-35 delay bin which is the subject of the enclosing notification. When this object is part of a tmnxOamPmThrRaise notification, the notification was raised because the number of PDUs with delay greater than or equal to tmnxOamPmNotifThrBinLowerBound (in the specified measurement interval) met or exceeded the configured threshold tmnxOamPmCfgThrDelayRaise. When this object is part of a tmnxOamPmThrClear notification, the notification was raised because the number of PDUs with delay greater than or equal to tmnxOamPmNotifThrBinLowerBound (in the specified measurement interval) was less than or equal to the configured threshold tmnxOamPmCfgThrDelayClear. For example, suppose an OAM-PM delay raise threshold is configured with tmnxOamPmCfgThrDelayRaise = 1000 and tmnxOamPmCfgThrDelayLowestBin = 6. Suppose the configured lower bound (i.e. tmnxOamPmCfgBinLowerBound) for the specified bin 6 is 30,000 microseconds. Then, if the count of PDUs with delay at or above 30,000 microseconds (e.g. tmnxOamPmStsDelayDmmBin2wyCount) is 1000, and a TCA is raised, this object will report 30,000. This value must be ignored if the enclosing notification is a loss TCA (i.e. when tmnxOamPmNotifThrType is not 'delay(1)').
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  Unsigned32  

tmnxOamPmThrRaise 1.3.6.1.4.1.6527.3.1.3.92.0.1
[CAUSE] A tmnxOamPmThrRaise trap is sent when an OAM-PM loss or delay counter meets or exceeds its configured raise threshold. If an Average Frame Loss Ratio (FLR) threshold (i.e. tmnxOamPmCfgThrLossAvgFlrRaise) is met or exceeded, the tmnxOamPmThrRaise trap is sent at the end of the measurement interval. If another type of threshold (e.g. tmnxOamPmCfgThrLossHliRaise) is met or exceeded, the tmnxOamPmThrRaise trap is sent when the problem is detected. The Average FLR threshold is a special case because the measured Average FLR can fluctuate during a measurement interval. At most one tmnxOamPmThrRaise trap is sent per threshold type during one OAM-PM measurement interval. For example, at most one tmnxOamPmThrRaise trap is sent to record an excessive High Loss Indicator (HLI) count in the forward direction seen in a particular 15 minute interval belonging to the SLM test belonging to OAM-PM session 'oamPmSession1'. OAM-PM thresholds are explained in the DESCRIPTION clauses of tmnxOamPmCfgThrDelayTable, tmnxOamPmCfgThrLossFwBwAgTable, and tmnxOamPmCfgThrLossFwBwTable. OAM-PM counters are explained in the DESCRIPTION clauses of the tmnxOamPmStatsTableObjs tables. [EFFECT] For an LMM test, the loss of live traffic has met or exceeded a configured threshold. For the other test types, the loss or delay of OAM-PM test probes has met or exceeded a configured threshold, indicating possible excessive loss or excessive delay of live traffic. [RECOVERY] Fix the cause of the excessive loss or excessive delay.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

tmnxOamPmThrClear 1.3.6.1.4.1.6527.3.1.3.92.0.2
[CAUSE] A tmnxOamPmThrClear trap is sent at the end of an OAM-PM measurement interval when a loss or delay counter meets or falls below its configured clear threshold. At most one tmnxOamPmThrClear trap is sent per tmnxOamPmThrRaise trap. OAM-PM thresholds are explained in the DESCRIPTION clauses of tmnxOamPmCfgThrDelayTable, tmnxOamPmCfgThrLossFwBwAgTable, and tmnxOamPmCfgThrLossFwBwTable. OAM-PM counters are explained in the DESCRIPTION clauses of the tmnxOamPmStatsTableObjs tables. [EFFECT] For an LMM test, the loss of live traffic has met or fallen below a configured threshold. For other test types, the loss or delay of OAM-PM test probes has met or fallen below a configured threshold, indicating a possible improvement in the loss or delay of live traffic. [RECOVERY] No recovery is required for this trap.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

tmnxOamPmV12v0Compliance 1.3.6.1.4.1.6527.3.1.1.92.1.1
The compliance statement for management of OAM Performance Monitoring on Nokia SROS series systems, release 12.0.
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

tmnxOamPmV13v0Compliance 1.3.6.1.4.1.6527.3.1.1.92.1.2
The compliance statement for management of additional OAM Performance Monitoring objects on Nokia SROS series systems, release 13.0.
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

tmnxOamPmV14v0Compliance 1.3.6.1.4.1.6527.3.1.1.92.1.3
The compliance statement for management of additional OAM Performance Monitoring objects on Nokia SROS series systems, release 14.0.
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

tmnxOamPmV12v0ObjGroup 1.3.6.1.4.1.6527.3.1.1.92.2.1.1
The group of objects supporting the OAM Performance Monitoring functionality on Nokia SROS Release 12.0.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxOamPmV13v0ObjGroup 1.3.6.1.4.1.6527.3.1.1.92.2.2.1
The group of additional objects supporting the OAM Performance Monitoring functionality on Nokia SROS Release 13.0.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxOamPmV14v0ObjGroup 1.3.6.1.4.1.6527.3.1.1.92.2.3.1
The group of additional objects supporting the OAM Performance Monitoring functionality on Nokia SROS Release 14.0.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxOamPmV13v0NotifyObjsGroup 1.3.6.1.4.1.6527.3.1.1.92.4.2.1
The group of accessible-for-notify objects supporting the OAM Performance Monitoring functionality on Nokia SROS Release 13.0.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxOamPmV14v0NotifyObjsGroup 1.3.6.1.4.1.6527.3.1.1.92.4.3.1
The group of accessible-for-notify objects supporting the OAM Performance Monitoring functionality on Nokia SROS Release 14.0.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxOamPmV13v0NotifGroup 1.3.6.1.4.1.6527.3.1.1.92.3.2.1
The group of OAM Performance Monitoring notifications supported by Nokia SROS Release 13.0.
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP