TIMETRA-L2TP-MIB

File: TIMETRA-L2TP-MIB.mib (343521 bytes)

Imported modules

SNMPv2-SMI HCNUM-TC SNMPv2-TC
INET-ADDRESS-MIB IF-MIB SNMPv2-CONF
TIMETRA-GLOBAL-MIB TIMETRA-TC-MIB TIMETRA-VRTR-MIB
TIMETRA-CHASSIS-MIB TIMETRA-PPP-MIB TIMETRA-SERV-MIB

Imported symbols

Integer32 Unsigned32 Counter32
Gauge32 Counter64 TimeTicks
MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
CounterBasedGauge64 RowStatus TEXTUAL-CONVENTION
DisplayString TimeStamp TruthValue
MacAddress InetAddressPrefixLength InetAddress
InetAddressType InetPortNumber InetAddressIPv4
InterfaceIndexOrZero OBJECT-GROUP MODULE-COMPLIANCE
NOTIFICATION-GROUP timetraSRMIBModules tmnxSRObjs
tmnxSRConfs tmnxSRNotifyPrefix TmnxAdminState
TmnxOperState TmnxActionType TNamedItem
TNamedItemOrEmpty TItemDescription TmnxVRtrIDOrZero
TmnxServId TmnxSubIdentStringOrEmpty TmnxSubProfileStringOrEmpty
TmnxSubRadServAlgorithm TmnxSlaProfileStringOrEmpty TmnxAncpStringOrZero
TmnxSubMgtIntDestIdOrEmpty TmnxAppProfileStringOrEmpty TmnxDefSubIdSource
TmnxAsciiSpecification TmnxPppoeSessionInfoOrigin TmnxPppoeUserNameOrEmpty
TmnxPppoeSessionType TmnxManagedRouteStatus TmnxPppNcpProtocol
TDirection TPIRRateOverride TCIRRateOverride
TBurstSizeBytesOverride TQosOverrideType TmnxAccessLoopEncapDataLink
TmnxAccessLoopEncaps1 TmnxAccessLoopEncaps2 TmnxMlpppEpClass
TmnxSubNasPortPrefixType TmnxSubNasPortSuffixType TmnxSubNasPortTypeType
TmnxBinarySpecification vRtrID vRtrIfName
tmnxChassisIndex tmnxCardSlotNum tmnxMDASlotNum
TmnxPppCpState svcId iesIfIndex

Defined Types

TmnxAlwaysNeverOrDefault  
The TmnxAlwaysNeverOrDefault data type is an enumerated integer that describes a 'boolean-like' value that can be set to a default value. The value 'default' specifies that the actual value must be derived from another object of the same type with a wider scope.
TEXTUAL-CONVENTION    
  INTEGER default(1), never(2), always(3)  

TmnxAlwaysOrNever  
The TmnxAlwaysOrNever data type is an enumerated integer that describes a 'boolean value that can be used together with the 'TmnxAlwaysNeverOrDefault' data type. Use 'TmnxAlwaysOrNever' at the highest level and 'TmnxAlwaysNeverOrDefault' at lower levels of inheritance.
TEXTUAL-CONVENTION    
  INTEGER never(2), always(3)  

TmnxL2tpActionTypeDrain  
The TmnxL2tpActionTypeDrain data type is an enumerated integer that describes the values used to specify the type of drain action.
TEXTUAL-CONVENTION    
  INTEGER drain(0), stopDrain(1), notApplicable(2)  

TmnxL2tpAuthSecret  
The TmnxL2tpAuthSecret data type contains a shared secret used during the tunnel authentication phase of tunnel establishment.
TEXTUAL-CONVENTION    
  DisplayString Size(0..32)  

TmnxL2tpAvpHidingMode  
The TmnxL2tpAvpHidingMode data type is an enumerated integer that describes when the H bit is set in an L2TP Attribute Value Pair (AVP). The value 'never' specifies that the H bit is never set. The value 'sensitive' specifies that the H bit is only set for AVP's containing sensitive information. The value 'always' specifies that the H bit is set for all AVP's where it is allowed. The value 'default' specifies that the actual value must be derived from another object of the same type but a wider scope.
TEXTUAL-CONVENTION    
  INTEGER default(1), never(2), sensitive(3), always(4)  

TmnxL2tpCdnResult  
The TmnxL2tpCdnResult data type is an enumerated integer that indicates the result of a CDN (Call-Disconnect-Notify) message.
TEXTUAL-CONVENTION    
  INTEGER noError(0), lossCarrier(1), generalError(2), admin(3), noFacTemporary(4), noFacPermanent(5), invalidDest(6), noCarrier(7), busy(8), noDialTone(9), notEstab(10), noFraming(11)  

TmnxL2tpConnectionId  
The TmnxL2tpConnectionId data type contains an identification number for a Layer Two Tunneling Protocol Connection.
TEXTUAL-CONVENTION    
  Unsigned32 0..4294967295  

TmnxL2tpDoChallenge  
The TmnxL2tpDoChallenge data type is an enumerated integer that describes when challenge-response authentication is to be used. The value 'never' specifies that challenge-response authentication is never used. The value 'always' specifies that challenge-response authentication is always used. The value 'default' specifies that the actual value must be derived from another object of the same type but a wider scope.
TEXTUAL-CONVENTION    
  INTEGER default(1), never(2), always(3)  

TmnxL2tpErrorMessage  
The TmnxL2tpErrorMessage data type describes an L2TP error condition in human readable form.
TEXTUAL-CONVENTION    
  DisplayString Size(0..255)  

TmnxL2tpGeneralError  
The TmnxL2tpGeneralError data type is an enumerated integer that indicates types of errors that are not specific to any particular L2TP request, but rather to protocol or message format errors.
TEXTUAL-CONVENTION    
  INTEGER noError(0), noControl(1), wrongLength(2), fieldOutOfRange(3), insufficientRes(4), sessionIdInvalid(5), vendorSpecific(6), tryAnother(7), unknownMandatory(8)  

TmnxL2tpHostNameOrEmpty  
The TmnxL2tpHostNameOrEmpty data type contains a valid string to identify the host name of a Layer Two Tunneling Protocol Tunnel remote system (client) or server. An empty string indicates that no host name is defined.
TEXTUAL-CONVENTION    
  DisplayString Size(0..64)  

TmnxL2tpIsaGrpId  
The TmnxL2tpIsaGrpId data type contains an identification number for a Layer Two Tunneling Protocol Integrated Service Adaptor group.
TEXTUAL-CONVENTION    
  Unsigned32 1..4  

TmnxL2tpIsaGrpIdOrZero  
The TmnxL2tpIsaGrpIdOrZero data type contains an identification number for a Layer Two Tunneling Protocol Integrated Service Adaptor (ISA) group. The value zero means that no L2TP ISA Group is defined.
TEXTUAL-CONVENTION    
  Unsigned32 0..4  

TmnxL2tpIsaMdaLoadBalanceMethod  
The TmnxL2tpIsaMdaLoadBalanceMethod data type is an enumerated integer that describes how new sessions are assigned to an L2TP ISA MDA. The value 'perSession' specifies that the lowest granularity for load-balancing is a session; each session can be assigned to a different ISA MDA. The value 'perTunnel' specifies that the lowest granularity for load-balancing is a tunnel; all sessions associated with the same tunnel are assigned to the same ISA MDA; this may be useful or required in certain cases, for example: - MLPPP with multiple links per bundle; - HPol intermediate destination arbiters where the intermediate destination is an L2TP tunnel. The meaning of the value 'default' depends on the object.
TEXTUAL-CONVENTION    
  INTEGER default(0), perSession(1), perTunnel(2)  

TmnxL2tpIsaMdaOperState  
The TmnxL2tpIsaMdaOperState data type is an enumerated integer that describes the values used to identify the operational state of the L2TP ISA MDA.
TEXTUAL-CONVENTION    
  INTEGER unknown(1), inService(2), outOfService(3), draining(4), drained(5)  

TmnxL2tpLcpKaHoldUpMplier  
The TmnxL2tpLcpKaHoldUpMplier data type contains a number that specifies how many LCP keepalive messages can be missed before the related session is brought down. The value '0' specifies that the actual value must be derived from another object of the same type but a wider scope.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 1..5  

TmnxL2tpLcpKaInterval  
The TmnxL2tpLcpKaInterval data type contains a number that specifies the time interval in seconds at which LCP echo requests are transmitted. The value '0' specifies that the actual value must be derived from another object of the same type but a wider scope.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 10..300  

TmnxL2tpMlpppEndpointClass  
The TmnxL2tpMlpppEndpointClass data type is an enumerated integer that specifies the class of an MLPPP endpoint specification. This is used to identify a value to be transmitted in the MLPPP Endpoint Discriminator Option The value 'ipv4Address' specifies that a configured IPv4 address be used. The value 'macAddress' specifies that a configured IEEE 802.1 MAC address be used. The meaning of 'default' depends on the object.
TEXTUAL-CONVENTION    
  INTEGER default(0), ipv4Address(2), macAddress(3)  

TmnxL2tpMlpppMaxFragDelay  
The TmnxL2tpMlpppMaxFragDelay data type contains a number that specifies the maximum delay of a fragment, expressed in milliseconds. The meaning of the value '0' depends on the object.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 5..1000  

TmnxL2tpMlpppReassemblyTimeout  
The TmnxL2tpMlpppReassemblyTimeout data type contains a number that specifies the maximum time, expressed in milliseconds, that the system will keep incomplete packets while reassembling fragments. The value '0' specifies that the actual value must be derived from another object of the same type but a wider scope.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 100 | 1000  

TmnxL2tpPeerAddrChangePolicy  
The TmnxL2tpPeerAddrChangePolicy data type is an enumerated integer that specifies what to do in case the system receives a L2TP response from another address than the one the request was sent to. The value 'accept' specifies that this system accepts any source IP address change of received L2TP control messages related to a locally originated tunnel in the state 'waitReply' and rejects any peer address change for other tunnels; in case the new peer IP address is accepted, it is learned and used as destination address in subsequent L2TP messages. The value 'ignore' specifies that this system ignores any source IP address change of received L2TP control messages, does not learn any new peer IP address and does not change the destination address in subsequent L2TP messages. The value 'reject' specifies that this system rejects any source IP address change of received L2TP control messages and drops those messages.
TEXTUAL-CONVENTION    
  INTEGER accept(1), ignore(2), reject(3)  

TmnxL2tpPppAuthentication  
The TmnxL2tpPppAuthentication data type is an enumerated integer that specifies what PPP authentication protocol(s) must be negotiated during the LCP phase. The value 'prefChap' specifies that an attempt is made to negotiate CHAP first, possibly followed by an attempt to negotiate PAP. The value 'prefPap' specifies that an attempt is made to negotiate PAP first, possibly followed by an attempt to negotiate CHAP. The value 'default (0)' specifies that the actual value must be derived from another object of the same type but a wider scope.
TEXTUAL-CONVENTION    
  INTEGER default(0), pap(1), chap(2), prefChap(3), prefPap(4)  

TmnxL2tpPppMtu  
The TmnxL2tpPppMtu data type contains a number that specifies the largest IP packet that can be sent out without being fragmented. The value '0' specifies that the actual value must be derived from another object of the same type but a wider scope.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 512..9212  

TmnxL2tpReceiveWindowSize  
The TmnxL2tpReceiveWindowSize data type contains a number that specifies the Receive Window Size (RWS). The value '0' specifies that the actual value must be derived from another object of the same type but a wider scope.
TEXTUAL-CONVENTION    
  Unsigned32 0 | 4..1024  

TmnxL2tpRoles  
The TmnxL2tpRoles data type is a set of roles.
TEXTUAL-CONVENTION    
  BITS roleLAC(0), roleLNS(1)  

TmnxL2tpSeOperState  
The TmnxL2tpTuOperState data type is an enumerated integer that describes the values used to identify the operational state of the L2TP session.
TEXTUAL-CONVENTION    
  INTEGER unknown(0), idle(1), waitTunnel(2), waitReply(3), waitAcceptance(4), waitConnected(5), established(6), closed(7), closedByPeer(8)  

TmnxL2tpSessionAssignMethod  
The TmnxL2tpSessionAssignMethod data type is an enumerated integer that describes how new sessions are assigned to one of the set of suitable tunnels that are available or could be made available. The value 'existingFirst' specifies that the first suitable tunnel is used or set up for the first session and re-used for all subsequent sessions. The value 'weighted' specifies that the sessions are shared between the available tunnels; if necessary, new tunnels are set up until the maximum number is reached; the distribution aims at an equal ratio of the actual number of sessions to the maximum number of sessions.
TEXTUAL-CONVENTION    
  INTEGER existingFirst(1), weighted(2)  

TmnxL2tpSessionId  
The TmnxL2tpSessionId data type contains an identification number for a Layer Two Tunneling Protocol Session. This data type is only meaningful in the context of L2TP version 2; in this case, the range of valid values is (1..65535). In the context of L2TP version 3, the value must be equal to 0.
TEXTUAL-CONVENTION    
  Unsigned32 0..65535  

TmnxL2tpStopCcnResult  
The TmnxL2tpStopCcnResult data type is an enumerated integer that indicates the result of a 'StopCCN' (Stop-Control-Connection-Notification) message.
TEXTUAL-CONVENTION    
  INTEGER noError(0), generalReq(1), generalErr(2), alreadyExists(3), reqNotAuth(4), version(5), reqShutDown(6), fsmError(7)  

TmnxL2tpTgOperState  
The TmnxL2tpTgOperState data type is an enumerated integer that describes the values used to identify the operational state of the L2TP tunnel group.
TEXTUAL-CONVENTION    
  INTEGER active(1), drain(2)  

TmnxL2tpTransportType  
The TmnxL2tpTransportType data type is an enumerated integer that describes the transport type (aka type of Packet-Switched Network) used to carry the L2TP messages.
TEXTUAL-CONVENTION    
  INTEGER unknown(0), udpIp(1)  

TmnxL2tpTunnelDestructTO  
The period of time, expressed in seconds, that the data of a disconnected tunnel persists before being removed. If the system needs the resources taken by the disconnected tunnel data, it may remove the data earlier. The value '-2' means that the actual value must be derived from another object of the same type but with a wider scope.
TEXTUAL-CONVENTION    
  Integer32 -2 | 60..86400  

TmnxL2tpTunnelGroupName  
The TmnxL2tpTunnelGroupName data type contains a valid string to identify a Layer Two Tunneling Protocol Tunnel Group.
TEXTUAL-CONVENTION    
  DisplayString Size(1..63)  

TmnxL2tpTunnelGroupNameOrEmpty  
The TmnxL2tpTunnelGroupNameOrEmpty data type contains a valid string to identify a Layer Two Tunneling Protocol Tunnel Group. An empty string indicates that no Tunnel Group is defined.
TEXTUAL-CONVENTION    
  DisplayString Size(0..63)  

TmnxL2tpTunnelHelloInterval  
The time interval, expresssed in seconds, between two consecutive tunnel Hello messages. The value '-1' means that the keepalive function is disabled. The value '-2' means that the actual value must be derived from another object of the same type but with a wider scope.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 60..3600  

TmnxL2tpTunnelId  
The TmnxL2tpTunnelId data type contains an identification number for a Layer Two Tunneling Protocol Tunnel. This data type is only meaningful in the context of L2TP version 2; in this case, the range of valid values is (1..65535). In the context of L2TP version 3, the value must be equal to 0.
TEXTUAL-CONVENTION    
  Unsigned32 0..65535  

TmnxL2tpTunnelIdleTO  
The period of time, expressed in seconds, that an established tunnel with no active sessions persists before being disconnected. A value of '-1' leaves a tunnel up indefinitely. The value '-2' means that the actual value must be derived from another object of the same type but with a wider scope.
TEXTUAL-CONVENTION    
  Integer32 -2 | -1 | 0..3600  

TmnxL2tpTunnelMaxRetx  
The number of retries allowed for a tunnel before its control connection goes down. The value '-2' means that the actual value must be derived from another object of the same type but with a wider scope.
TEXTUAL-CONVENTION    
  Integer32 -2 | 2..7  

TmnxL2tpTunnelName  
The TmnxL2tpTunnelName data type contains a valid string to identify a Layer Two Tunneling Protocol Tunnel.
TEXTUAL-CONVENTION    
  DisplayString Size(1..63)  

TmnxL2tpTunnelNameOrEmpty  
The TmnxL2tpTunnelNameOrEmpty data type contains a valid string to identify a Layer Two Tunneling Protocol Tunnel. An empty string indicates that no Tunnel is defined.
TEXTUAL-CONVENTION    
  DisplayString Size(0..63)  

TmnxL2tpTunnelPreference  
The TmnxL2tpTunnelPreference data type contains a number that indicates the relative preference assigned to a tunnel. The value '0' corresponds to the highest preference.
TEXTUAL-CONVENTION    
  Unsigned32 0..16777215  

TmnxL2tpTunnelSessionLimit  
The number of sessions allowed.
TEXTUAL-CONVENTION    
  Integer32 1..131071  

TmnxL2tpTuOperState  
The TmnxL2tpTuOperState data type is an enumerated integer that describes the values used to identify the operational state of the L2TP tunnel.
TEXTUAL-CONVENTION    
  INTEGER unknown(1), idle(2), waitReply(3), waitConn(4), establishedIdle(5), established(6), draining(7), drained(8), closed(9), closedByPeer(10)  

TmnxL2tpTuProtStatsType  
The TmnxL2tpTuProtStatsType data type is an enumerated integer that describes the values used to identify the protocol statistics of the L2TP tunnel.
TEXTUAL-CONVENTION    
  INTEGER event(1), droppedMsgType(2), acceptedMsgType(3), originalTransmittedMsgType(4), retransmittedMsgType(5), incomingCDNresultCode(6), incomingStopCCNresultCode(7), incomingErrorCode(8), outgoingCDNresultCode(9), outgoingStopCCNresultCode(10), outgoingErrorCode(11)  

TmnxL2tpEntry  
SEQUENCE    
  tmnxL2tpLastMgmtChange TimeStamp
  tmnxL2tpAdminState TmnxAdminState
  tmnxL2tpSessionLimit TmnxL2tpTunnelSessionLimit
  tmnxL2tpReceiveWindowSize TmnxL2tpReceiveWindowSize
  tmnxL2tpRowStatus RowStatus
  tmnxL2tpPeerAddrChangePlcy TmnxL2tpPeerAddrChangePolicy
  tmnxL2tpAvpExclude BITS
  tmnxL2tpAvpCallingNumberSpec TmnxAsciiSpecification
  tmnxL2tpAccountingPolicy TNamedItemOrEmpty

TmnxL2tpStatEntry  
SEQUENCE    
  tmnxL2tpStatCleared TimeStamp
  tmnxL2tpStatTotalTunnels Counter32
  tmnxL2tpStatFailedTunnels Counter32
  tmnxL2tpStatFailedTuAuth Counter32
  tmnxL2tpStatActiveTunnels Gauge32
  tmnxL2tpStatTotalSessions Counter32
  tmnxL2tpStatFailedSessions Counter32
  tmnxL2tpStatActiveSessions Gauge32
  tmnxL2tpStatCurrentTunnels Gauge32
  tmnxL2tpStatCurrentSessions Gauge32

TmnxL2tpTgCfgEntry  
SEQUENCE    
  tmnxL2tpTgCfgName TmnxL2tpTunnelGroupName
  tmnxL2tpTgCfgRowStatus RowStatus
  tmnxL2tpTgCfgLastMgmtChange TimeStamp
  tmnxL2tpTgCfgDescription TItemDescription
  tmnxL2tpTgCfgAdminState TmnxAdminState
  tmnxL2tpTgCfgSecret TmnxL2tpAuthSecret
  tmnxL2tpTgCfgHelloInterval TmnxL2tpTunnelHelloInterval
  tmnxL2tpTgCfgIdleTO TmnxL2tpTunnelIdleTO
  tmnxL2tpTgCfgDestructTO TmnxL2tpTunnelDestructTO
  tmnxL2tpTgCfgMaxRetxEstab TmnxL2tpTunnelMaxRetx
  tmnxL2tpTgCfgMaxRetxNotEstab TmnxL2tpTunnelMaxRetx
  tmnxL2tpTgCfgSessionLimit TmnxL2tpTunnelSessionLimit
  tmnxL2tpTgCfgAvpHiding TmnxL2tpAvpHidingMode
  tmnxL2tpTgCfgSessionAssignMethod TmnxL2tpSessionAssignMethod
  tmnxL2tpTgCfgLocalName TmnxL2tpHostNameOrEmpty
  tmnxL2tpTgCfgDoChallenge TmnxL2tpDoChallenge
  tmnxL2tpTgCfgReceiveWindowSize TmnxL2tpReceiveWindowSize
  tmnxL2tpTgCfgIsaGrpId TmnxL2tpIsaGrpIdOrZero
  tmnxL2tpTgCfgAddrType InetAddressType
  tmnxL2tpTgCfgAddr InetAddress
  tmnxL2tpTgCfgLoadBalanceMethod TmnxL2tpIsaMdaLoadBalanceMethod
  tmnxL2tpTgCfgAccountingPolicy TNamedItemOrEmpty

TmnxL2tpLnsTgPppEntry  
SEQUENCE    
  tmnxL2tpLnsTgPppLastMgmtChange TimeStamp
  tmnxL2tpLnsTgPppAuthPlcy TNamedItemOrEmpty
  tmnxL2tpLnsTgPppAuthProtocol TmnxL2tpPppAuthentication
  tmnxL2tpLnsTgPppUserDb TNamedItemOrEmpty
  tmnxL2tpLnsTgPppDefaultService TmnxServId
  tmnxL2tpLnsTgPppDefaultGroupIf TNamedItemOrEmpty
  tmnxL2tpLnsTgPppProxyLcp TmnxAlwaysOrNever
  tmnxL2tpLnsTgPppProxyAuth TmnxAlwaysOrNever
  tmnxL2tpLnsTgPppMtu TmnxL2tpPppMtu
  tmnxL2tpLnsTgPppLcpKaInterval TmnxL2tpLcpKaInterval
  tmnxL2tpLnsTgPppLcpKaHoldUp TmnxL2tpLcpKaHoldUpMplier
  tmnxL2tpLnsTgPppIpcpSubnetNeg TmnxAlwaysOrNever

TmnxL2tpTgMlpppEntry  
SEQUENCE    
  tmnxL2tpTgMlpppLastMgmtChange TimeStamp
  tmnxL2tpTgMlpppAdminState TmnxAdminState
  tmnxL2tpTgMlpppMaxLinks Unsigned32
  tmnxL2tpTgMlpppInterleave TmnxAlwaysOrNever
  tmnxL2tpTgMlpppMaxFragDelay TmnxL2tpMlpppMaxFragDelay
  tmnxL2tpTgMlpppReassemblyTo TmnxL2tpMlpppReassemblyTimeout
  tmnxL2tpTgMlpppShortSeqNumberRx TmnxAlwaysOrNever
  tmnxL2tpTgMlpppEpClass TmnxL2tpMlpppEndpointClass
  tmnxL2tpTgMlpppEpIpv4Address InetAddressIPv4
  tmnxL2tpTgMlpppEpMacAddress MacAddress

TmnxL2tpTgStatEntry  
SEQUENCE    
  tmnxL2tpTgStatName TmnxL2tpTunnelGroupName
  tmnxL2tpTgStatState TmnxL2tpTgOperState
  tmnxL2tpTgStatCleared TimeStamp
  tmnxL2tpTgStatTotalTunnels Counter32
  tmnxL2tpTgStatFailedTunnels Counter32
  tmnxL2tpTgStatFailedTuAuth Counter32
  tmnxL2tpTgStatActiveTunnels Gauge32
  tmnxL2tpTgStatTunnels Gauge32
  tmnxL2tpTgStatTotalSessions Counter32
  tmnxL2tpTgStatFailedSessions Counter32
  tmnxL2tpTgStatActiveSessions Gauge32
  tmnxL2tpTgStatSessions Gauge32
  tmnxL2tpTgStatControlRxOctets CounterBasedGauge64
  tmnxL2tpTgStatControlRxOctetsLw Gauge32
  tmnxL2tpTgStatControlRxOctetsHw Gauge32
  tmnxL2tpTgStatControlRxPkts Gauge32
  tmnxL2tpTgStatControlTxOctets CounterBasedGauge64
  tmnxL2tpTgStatControlTxOctetsLw Gauge32
  tmnxL2tpTgStatControlTxOctetsHw Gauge32
  tmnxL2tpTgStatControlTxPkts Gauge32
  tmnxL2tpTgStatErrorTxPkts Gauge32
  tmnxL2tpTgStatErrorRxPkts Gauge32
  tmnxL2tpTgStatSessionLimit Gauge32
  tmnxL2tpTgStatSeAssignMethod TmnxL2tpSessionAssignMethod

TmnxL2tpTgTuEntry  
SEQUENCE    
  tmnxL2tpTgTuId TmnxL2tpConnectionId

TmnxL2tpTgDrainEntry  
SEQUENCE    
  tmnxL2tpTgDrain TmnxL2tpActionTypeDrain

TmnxL2tpTuCfgEntry  
SEQUENCE    
  tmnxL2tpTuCfgName TNamedItem
  tmnxL2tpTuCfgRowStatus RowStatus
  tmnxL2tpTuCfgLastMgmtChange TimeStamp
  tmnxL2tpTuCfgDescription TItemDescription
  tmnxL2tpTuCfgAdminState TmnxAdminState
  tmnxL2tpTuCfgPreference TmnxL2tpTunnelPreference
  tmnxL2tpTuCfgPeerAddrType InetAddressType
  tmnxL2tpTuCfgPeerAddr InetAddress
  tmnxL2tpTuCfgAddrType InetAddressType
  tmnxL2tpTuCfgAddr InetAddress
  tmnxL2tpTuCfgLocalName TmnxL2tpHostNameOrEmpty
  tmnxL2tpTuCfgRemoteName TmnxL2tpHostNameOrEmpty
  tmnxL2tpTuCfgSecret TmnxL2tpAuthSecret
  tmnxL2tpTuCfgHelloInterval TmnxL2tpTunnelHelloInterval
  tmnxL2tpTuCfgIdleTO TmnxL2tpTunnelIdleTO
  tmnxL2tpTuCfgDestructTO TmnxL2tpTunnelDestructTO
  tmnxL2tpTuCfgMaxRetxEstab TmnxL2tpTunnelMaxRetx
  tmnxL2tpTuCfgMaxRetxNotEstab TmnxL2tpTunnelMaxRetx
  tmnxL2tpTuCfgSessionLimit TmnxL2tpTunnelSessionLimit
  tmnxL2tpTuCfgAvpHiding TmnxL2tpAvpHidingMode
  tmnxL2tpTuCfgAutoEstab TruthValue
  tmnxL2tpTuCfgDoChallenge TmnxL2tpDoChallenge
  tmnxL2tpTuCfgReceiveWindowSize TmnxL2tpReceiveWindowSize
  tmnxL2tpTuCfgIsaGrpId TmnxL2tpIsaGrpIdOrZero
  tmnxL2tpTuCfgLoadBalanceMethod TmnxL2tpIsaMdaLoadBalanceMethod
  tmnxL2tpTuCfgAccountingPolicy TNamedItemOrEmpty

TmnxL2tpLnsTuPppEntry  
SEQUENCE    
  tmnxL2tpLnsTuPppLastMgmtChange TimeStamp
  tmnxL2tpLnsTuPppAuthPlcy TNamedItemOrEmpty
  tmnxL2tpLnsTuPppAuthProtocol TmnxL2tpPppAuthentication
  tmnxL2tpLnsTuPppUserDb TNamedItemOrEmpty
  tmnxL2tpLnsTuPppDefaultService TmnxServId
  tmnxL2tpLnsTuPppDefaultGroupIf TNamedItemOrEmpty
  tmnxL2tpLnsTuPppProxyLcp TmnxAlwaysNeverOrDefault
  tmnxL2tpLnsTuPppProxyAuth TmnxAlwaysNeverOrDefault
  tmnxL2tpLnsTuPppMtu TmnxL2tpPppMtu
  tmnxL2tpLnsTuPppLcpKaInterval TmnxL2tpLcpKaInterval
  tmnxL2tpLnsTuPppLcpKaHoldUp TmnxL2tpLcpKaHoldUpMplier
  tmnxL2tpLnsTuPppIpcpSubnetNeg TmnxAlwaysNeverOrDefault

TmnxL2tpTuMlpppEntry  
SEQUENCE    
  tmnxL2tpTuMlpppLastMgmtChange TimeStamp
  tmnxL2tpTuMlpppAdminState TmnxAdminState
  tmnxL2tpTuMlpppMaxLinks Unsigned32
  tmnxL2tpTuMlpppInterleave TmnxAlwaysNeverOrDefault
  tmnxL2tpTuMlpppMaxFragDelay TmnxL2tpMlpppMaxFragDelay
  tmnxL2tpTuMlpppReassemblyTo TmnxL2tpMlpppReassemblyTimeout
  tmnxL2tpTuMlpppShortSeqNumberRx TmnxAlwaysNeverOrDefault
  tmnxL2tpTuMlpppEpClass TmnxL2tpMlpppEndpointClass
  tmnxL2tpTuMlpppEpIpv4Address InetAddressIPv4
  tmnxL2tpTuMlpppEpMacAddress MacAddress

TmnxL2tpTuStatusEntry  
SEQUENCE    
  tmnxL2tpTuStatusId TmnxL2tpConnectionId
  tmnxL2tpTuStatusState TmnxL2tpTuOperState
  tmnxL2tpTuStatusTunnelId TmnxL2tpTunnelId
  tmnxL2tpTuStatusPreference TmnxL2tpTunnelPreference
  tmnxL2tpTuStatusPeerAddrType InetAddressType
  tmnxL2tpTuStatusPeerAddr InetAddress
  tmnxL2tpTuStatusAddrType InetAddressType
  tmnxL2tpTuStatusAddr InetAddress
  tmnxL2tpTuStatusLocalName TmnxL2tpHostNameOrEmpty
  tmnxL2tpTuStatusRemoteName TmnxL2tpHostNameOrEmpty
  tmnxL2tpTuStatusAssignmentId TmnxL2tpTunnelNameOrEmpty
  tmnxL2tpTuStatusHelloInterval TmnxL2tpTunnelHelloInterval
  tmnxL2tpTuStatusIdleTO TmnxL2tpTunnelIdleTO
  tmnxL2tpTuStatusDestructTO TmnxL2tpTunnelDestructTO
  tmnxL2tpTuStatusMaxRetxEstab TmnxL2tpTunnelMaxRetx
  tmnxL2tpTuStatusMaxRetxNotEstab TmnxL2tpTunnelMaxRetx
  tmnxL2tpTuStatusSessionLimit TmnxL2tpTunnelSessionLimit
  tmnxL2tpTuStatusAvpHiding TmnxL2tpAvpHidingMode
  tmnxL2tpTuStatusGroupName TmnxL2tpTunnelGroupNameOrEmpty
  tmnxL2tpTuStatusRemoteTunnelId TmnxL2tpTunnelId
  tmnxL2tpTuStatusRemoteConnId TmnxL2tpConnectionId
  tmnxL2tpTuStatusTransportType TmnxL2tpTransportType
  tmnxL2tpTuStatusUdpPort InetPortNumber
  tmnxL2tpTuStatusRemoteUdpPort InetPortNumber
  tmnxL2tpTuStatusStartTime TimeStamp
  tmnxL2tpTuStatusEstabTime TimeStamp
  tmnxL2tpTuStatusIdleTime TimeStamp
  tmnxL2tpTuStatusClosedTime TimeStamp
  tmnxL2tpTuStatusStopCcnResult TmnxL2tpStopCcnResult
  tmnxL2tpTuStatusGeneralError TmnxL2tpGeneralError
  tmnxL2tpTuStatusErrorMessage TmnxL2tpErrorMessage
  tmnxL2tpTuStatusDoChallenge TmnxL2tpDoChallenge
  tmnxL2tpTuStatusRws Unsigned32
  tmnxL2tpTuStatusTxDestAddrType InetAddressType
  tmnxL2tpTuStatusTxDestAddr InetAddress
  tmnxL2tpTuStatusRxSrcAddrType InetAddressType
  tmnxL2tpTuStatusRxSrcAddr InetAddress
  tmnxL2tpTuStatusAccountingPolicy TNamedItemOrEmpty

TmnxL2tpTuStatsEntry  
SEQUENCE    
  tmnxL2tpTuStatsLastCleared TimeStamp
  tmnxL2tpTuStatsTotalSessions Counter32
  tmnxL2tpTuStatsFailedSessions Counter32
  tmnxL2tpTuStatsActiveSessions Gauge32
  tmnxL2tpTuStatsSessions Gauge32
  tmnxL2tpTuStatsControlRxOctets Counter64
  tmnxL2tpTuStatsControlRxOctetsLw Counter32
  tmnxL2tpTuStatsControlRxOctetsHw Counter32
  tmnxL2tpTuStatsControlRxPkts Counter32
  tmnxL2tpTuStatsControlTxOctets Counter64
  tmnxL2tpTuStatsControlTxOctetsLw Counter32
  tmnxL2tpTuStatsControlTxOctetsHw Counter32
  tmnxL2tpTuStatsControlTxPkts Counter32
  tmnxL2tpTuStatsErrorTxPkts Counter32
  tmnxL2tpTuStatsErrorRxPkts Counter32
  tmnxL2tpTuStatsFsmMsgAccepted Counter32
  tmnxL2tpTuStatsFsmMsgDuplicateRx Counter32
  tmnxL2tpTuStatsFsmMsgOutOfWndwRx Counter32
  tmnxL2tpTuStatsQLengthUnsentMax Gauge32
  tmnxL2tpTuStatsQLengthUnsentCur Gauge32
  tmnxL2tpTuStatsQLengthAckMax Gauge32
  tmnxL2tpTuStatsQLengthAckCur Gauge32
  tmnxL2tpTuStatsWindowSizeCur Gauge32

TmnxL2tpTuProtStatsEntry  
SEQUENCE    
  tmnxL2tpTuProtStatsType TmnxL2tpTuProtStatsType
  tmnxL2tpTuProtStatsInstance Unsigned32
  tmnxL2tpTuProtStatsName DisplayString
  tmnxL2tpTuProtStatsVal Counter32

TmnxL2tpTuStartEntry  
SEQUENCE    
  tmnxL2tpTuStart TmnxActionType

TmnxL2tpTuStopEntry  
SEQUENCE    
  tmnxL2tpTuStop TmnxActionType

TmnxL2tpTuDrainEntry  
SEQUENCE    
  tmnxL2tpTuDrain TmnxL2tpActionTypeDrain

TmnxL2tpPeerStatEntry  
SEQUENCE    
  tmnxL2tpPeerStatRole INTEGER
  tmnxL2tpPeerStatActiveTunnels Gauge32
  tmnxL2tpPeerStatTunnels Gauge32
  tmnxL2tpPeerStatActiveSessions Gauge32
  tmnxL2tpPeerStatSessions Gauge32
  tmnxL2tpPeerStatDraining TruthValue
  tmnxL2tpPeerStatUnreachable TruthValue
  tmnxL2tpPeerStatUnreachableTime TimeStamp
  tmnxL2tpPeerStatControlRxOct Counter64
  tmnxL2tpPeerStatControlRxOctLw Counter32
  tmnxL2tpPeerStatControlRxOctHw Counter32
  tmnxL2tpPeerStatControlRxPkts Counter32
  tmnxL2tpPeerStatControlTxOct Counter64
  tmnxL2tpPeerStatControlTxOctLw Counter32
  tmnxL2tpPeerStatControlTxOctHw Counter32
  tmnxL2tpPeerStatControlTxPkts Counter32
  tmnxL2tpPeerStatErrorTxPkts Counter32
  tmnxL2tpPeerStatErrorRxPkts Counter32
  tmnxL2tpPeerStatMsgAccepted Counter32
  tmnxL2tpPeerStatMsgDuplicateRx Counter32
  tmnxL2tpPeerStatMsgOutOfWndwRx Counter32
  tmnxL2tpPeerStatRolesCapability TmnxL2tpRoles
  tmnxL2tpPeerStatRoles TmnxL2tpRoles
  tmnxL2tpPeerStatLastCleared TimeStamp

TmnxL2tpPeerTuEntry  
SEQUENCE    
  tmnxL2tpPeerTuId TmnxL2tpConnectionId

TmnxL2tpPeerProtStatsEntry  
SEQUENCE    
  tmnxL2tpPeerProtStatsTransport TmnxL2tpTransportType
  tmnxL2tpPeerProtStatsAddrType InetAddressType
  tmnxL2tpPeerProtStatsAddr InetAddress
  tmnxL2tpPeerProtStatsRemUdpPort InetPortNumber
  tmnxL2tpPeerProtStatsType TmnxL2tpTuProtStatsType
  tmnxL2tpPeerProtStatsInstance Unsigned32
  tmnxL2tpPeerProtStatsName DisplayString
  tmnxL2tpPeerProtStatsVal Counter32

TmnxL2tpPeerDrainEntry  
SEQUENCE    
  tmnxL2tpPeerDrain TmnxL2tpActionTypeDrain

TmnxL2tpSeStatusEntry  
SEQUENCE    
  tmnxL2tpSeStatusId TmnxL2tpConnectionId
  tmnxL2tpSeStatusState TmnxL2tpSeOperState
  tmnxL2tpSeStatusTunnelId TmnxL2tpTunnelId
  tmnxL2tpSeStatusTunnelConnId TmnxL2tpConnectionId
  tmnxL2tpSeStatusSessionId TmnxL2tpSessionId
  tmnxL2tpSeStatusRemoteTunnelId TmnxL2tpTunnelId
  tmnxL2tpSeStatusRemoteSessionId TmnxL2tpSessionId
  tmnxL2tpSeStatusRemoteConnId TmnxL2tpConnectionId
  tmnxL2tpSeStatusStartTime TimeStamp
  tmnxL2tpSeStatusEstabTime TimeStamp
  tmnxL2tpSeStatusClosedTime TimeStamp
  tmnxL2tpSeStatusCdnResult TmnxL2tpCdnResult
  tmnxL2tpSeStatusGeneralError TmnxL2tpGeneralError
  tmnxL2tpSeStatusErrorMessage TmnxL2tpErrorMessage
  tmnxL2tpSeStatusMlpppBundleIndex Unsigned32

TmnxL2tpLnsSePppEntry  
SEQUENCE    
  tmnxL2tpLnsSePppUpTime TimeTicks
  tmnxL2tpLnsSePppLcpState TmnxPppCpState
  tmnxL2tpLnsSePppIpcpState TmnxPppCpState
  tmnxL2tpLnsSePppPppMtu Unsigned32
  tmnxL2tpLnsSePppPppAuthProtocol INTEGER
  tmnxL2tpLnsSePppPppUserName TmnxPppoeUserNameOrEmpty
  tmnxL2tpLnsSePppSubIdent TmnxSubIdentStringOrEmpty
  tmnxL2tpLnsSePppOriginSubIdent TmnxPppoeSessionInfoOrigin
  tmnxL2tpLnsSePppSubProfString TmnxSubProfileStringOrEmpty
  tmnxL2tpLnsSePppSlaProfString TmnxSlaProfileStringOrEmpty
  tmnxL2tpLnsSePppAncpString TmnxAncpStringOrZero
  tmnxL2tpLnsSePppInterDestId TmnxSubMgtIntDestIdOrEmpty
  tmnxL2tpLnsSePppAppProfString TmnxAppProfileStringOrEmpty
  tmnxL2tpLnsSePppOriginStrings TmnxPppoeSessionInfoOrigin
  tmnxL2tpLnsSePppSessionTimeout Unsigned32
  tmnxL2tpLnsSePppIpAddrType InetAddressType
  tmnxL2tpLnsSePppIpAddr InetAddress
  tmnxL2tpLnsSePppPrimaryDnsType InetAddressType
  tmnxL2tpLnsSePppPrimaryDns InetAddress
  tmnxL2tpLnsSePppSecondaryDnsType InetAddressType
  tmnxL2tpLnsSePppSecondaryDns InetAddress
  tmnxL2tpLnsSePppPrimaryNbnsType InetAddressType
  tmnxL2tpLnsSePppPrimaryNbns InetAddress
  tmnxL2tpLnsSePppSecondNbnsType InetAddressType
  tmnxL2tpLnsSePppSecondNbns InetAddress
  tmnxL2tpLnsSePppOriginIpcpInfo TmnxPppoeSessionInfoOrigin
  tmnxL2tpLnsSePppCircuitId OCTET STRING
  tmnxL2tpLnsSePppRemoteId OCTET STRING
  tmnxL2tpLnsSePppAddressPool DisplayString
  tmnxL2tpLnsSePppType TmnxPppoeSessionType
  tmnxL2tpLnsSePppSvcId TmnxServId
  tmnxL2tpLnsSePppGrpIf InterfaceIndexOrZero
  tmnxL2tpLnsSePppL2tpVrtrId TmnxVRtrIDOrZero
  tmnxL2tpLnsSePppL2tpConnectionId Unsigned32
  tmnxL2tpLnsSePppCategoryMapName TNamedItemOrEmpty
  tmnxL2tpLnsSePppRadiusClassAttr OCTET STRING
  tmnxL2tpLnsSePppRadiusUserName DisplayString
  tmnxL2tpLnsSePppIpv6cpState TmnxPppCpState
  tmnxL2tpLnsSePppInterfaceId OCTET STRING
  tmnxL2tpLnsSePppOriginIpv6cpInfo TmnxPppoeSessionInfoOrigin
  tmnxL2tpLnsSePppIpv6DnsType InetAddressType
  tmnxL2tpLnsSePppIpv6Dns1 InetAddress
  tmnxL2tpLnsSePppIpv6Dns2 InetAddress
  tmnxL2tpLnsSePppIpv6DelPfxType InetAddressType
  tmnxL2tpLnsSePppIpv6DelPfxLen InetAddressPrefixLength
  tmnxL2tpLnsSePppIpv6DelPfx InetAddress
  tmnxL2tpLnsSePppIpv6PrefixType InetAddressType
  tmnxL2tpLnsSePppIpv6PrefixLen InetAddressPrefixLength
  tmnxL2tpLnsSePppIpv6Prefix InetAddress
  tmnxL2tpLnsSePppSubPppIndex Unsigned32

TmnxL2tpLnsSePppStatEntry  
SEQUENCE    
  tmnxL2tpLnsSePppStatRxUnkwnProto Counter32
  tmnxL2tpLnsSePppStatRxLcpConfRq Counter32
  tmnxL2tpLnsSePppStatRxLcpConfAk Counter32
  tmnxL2tpLnsSePppStatRxLcpConfNk Counter32
  tmnxL2tpLnsSePppStatRxLcpConfRj Counter32
  tmnxL2tpLnsSePppStatRxLcpTermRq Counter32
  tmnxL2tpLnsSePppStatRxLcpTermAk Counter32
  tmnxL2tpLnsSePppStatRxLcpCodeRj Counter32
  tmnxL2tpLnsSePppStatRxLcpEchoRq Counter32
  tmnxL2tpLnsSePppStatRxLcpEchoRep Counter32
  tmnxL2tpLnsSePppStatRxLcpProtRj Counter32
  tmnxL2tpLnsSePppStatRxLcpDiscRq Counter32
  tmnxL2tpLnsSePppStatTxLcpConfRq Counter32
  tmnxL2tpLnsSePppStatTxLcpConfAk Counter32
  tmnxL2tpLnsSePppStatTxLcpConfNk Counter32
  tmnxL2tpLnsSePppStatTxLcpConfRj Counter32
  tmnxL2tpLnsSePppStatTxLcpTermRq Counter32
  tmnxL2tpLnsSePppStatTxLcpTermAk Counter32
  tmnxL2tpLnsSePppStatTxLcpCodeRj Counter32
  tmnxL2tpLnsSePppStatTxLcpEchoRq Counter32
  tmnxL2tpLnsSePppStatTxLcpEchoRep Counter32
  tmnxL2tpLnsSePppStatTxLcpProtRj Counter32
  tmnxL2tpLnsSePppStatTxLcpDiscRq Counter32
  tmnxL2tpLnsSePppStatRxPapAuthRq Counter32
  tmnxL2tpLnsSePppStatTxPapAuthAk Counter32
  tmnxL2tpLnsSePppStatTxPapAuthNk Counter32
  tmnxL2tpLnsSePppStatRxChapResp Counter32
  tmnxL2tpLnsSePppStatTxChapChall Counter32
  tmnxL2tpLnsSePppStatTxChapSucc Counter32
  tmnxL2tpLnsSePppStatTxChapFail Counter32
  tmnxL2tpLnsSePppStatRxIpcpConfRq Counter32
  tmnxL2tpLnsSePppStatRxIpcpConfAk Counter32
  tmnxL2tpLnsSePppStatRxIpcpConfNk Counter32
  tmnxL2tpLnsSePppStatRxIpcpConfRj Counter32
  tmnxL2tpLnsSePppStatRxIpcpTermRq Counter32
  tmnxL2tpLnsSePppStatRxIpcpTermAk Counter32
  tmnxL2tpLnsSePppStatRxIpcpCodeRj Counter32
  tmnxL2tpLnsSePppStatTxIpcpConfRq Counter32
  tmnxL2tpLnsSePppStatTxIpcpConfAk Counter32
  tmnxL2tpLnsSePppStatTxIpcpConfNk Counter32
  tmnxL2tpLnsSePppStatTxIpcpConfRj Counter32
  tmnxL2tpLnsSePppStatTxIpcpTermRq Counter32
  tmnxL2tpLnsSePppStatTxIpcpTermAk Counter32
  tmnxL2tpLnsSePppStatTxIpcpCodeRj Counter32
  tmnxL2tpLnsSePppStatRxIpv6cpCfRq Counter32
  tmnxL2tpLnsSePppStatRxIpv6cpCfAk Counter32
  tmnxL2tpLnsSePppStatRxIpv6cpCfNk Counter32
  tmnxL2tpLnsSePppStatRxIpv6cpCfRj Counter32
  tmnxL2tpLnsSePppStatRxIpv6cpTmRq Counter32
  tmnxL2tpLnsSePppStatRxIpv6cpTmAk Counter32
  tmnxL2tpLnsSePppStatRxIpv6cpCdRj Counter32
  tmnxL2tpLnsSePppStatTxIpv6cpCfRq Counter32
  tmnxL2tpLnsSePppStatTxIpv6cpCfAk Counter32
  tmnxL2tpLnsSePppStatTxIpv6cpCfNk Counter32
  tmnxL2tpLnsSePppStatTxIpv6cpCfRj Counter32
  tmnxL2tpLnsSePppStatTxIpv6cpTmRq Counter32
  tmnxL2tpLnsSePppStatTxIpv6cpTmAk Counter32
  tmnxL2tpLnsSePppStatTxIpv6cpCdRj Counter32

TmnxL2tpLnsSeMRtEntry  
SEQUENCE    
  tmnxL2tpLnsSeMRtAddrType InetAddressType
  tmnxL2tpLnsSeMRtAddr InetAddress
  tmnxL2tpLnsSeMRtPrefixLen InetAddressPrefixLength
  tmnxL2tpLnsSeMRtStatus TmnxManagedRouteStatus

TmnxL2tpLnsSeOvrEntry  
SEQUENCE    
  tmnxL2tpLnsSeOvrDirection TDirection
  tmnxL2tpLnsSeOvrType TQosOverrideType
  tmnxL2tpLnsSeOvrTypeId Integer32
  tmnxL2tpLnsSeOvrTypeName TNamedItemOrEmpty
  tmnxL2tpLnsSeOvrPIR TPIRRateOverride
  tmnxL2tpLnsSeOvrCIR TCIRRateOverride
  tmnxL2tpLnsSeOvrCBS TBurstSizeBytesOverride
  tmnxL2tpLnsSeOvrMBS TBurstSizeBytesOverride

TmnxL2tpLnsSeAleEntry  
SEQUENCE    
  tmnxL2tpLnsSeAleDatalink TmnxAccessLoopEncapDataLink
  tmnxL2tpLnsSeAleEncaps1 TmnxAccessLoopEncaps1
  tmnxL2tpLnsSeAleEncaps2 TmnxAccessLoopEncaps2

TmnxL2tpSeStopEntry  
SEQUENCE    
  tmnxL2tpSeStop TmnxActionType

TmnxL2tpIsaGrpEntry  
SEQUENCE    
  tmnxL2tpIsaGrpId TmnxL2tpIsaGrpId
  tmnxL2tpIsaGrpRowStatus RowStatus
  tmnxL2tpIsaGrpLastMgmtChange TimeStamp
  tmnxL2tpIsaGrpDescription TItemDescription
  tmnxL2tpIsaGrpAdminState TmnxAdminState
  tmnxL2tpIsaGrpOperState TmnxOperState
  tmnxL2tpIsaGrpPortPlcy TNamedItemOrEmpty

TmnxL2tpIsaMdaEntry  
SEQUENCE    
  tmnxL2tpIsaMdaRowStatus RowStatus
  tmnxL2tpIsaMdaLastMgmtChange TimeStamp
  tmnxL2tpIsaMdaDrain TruthValue
  tmnxL2tpIsaMdaStop TmnxActionType

TmnxL2tpIsaMdaStatEntry  
SEQUENCE    
  tmnxL2tpIsaMdaStatOperState TmnxL2tpIsaMdaOperState
  tmnxL2tpIsaMdaStatSessions Gauge32

TmnxL2tpIsaMdaVRtrEntry  
SEQUENCE    
  tmnxL2tpIsaMdaVRtrOperState TmnxOperState

TmnxL2tpLnsIfEntry  
SEQUENCE    
  tmnxL2tpLnsIfLastMgmtChange TimeStamp
  tmnxL2tpLnsIfDescription TItemDescription
  tmnxL2tpLnsIfDefSubProfile TNamedItemOrEmpty
  tmnxL2tpLnsIfDefSlaProfile TNamedItemOrEmpty
  tmnxL2tpLnsIfDefAppProfile TNamedItemOrEmpty
  tmnxL2tpLnsIfSubIdentPolicy TNamedItemOrEmpty
  tmnxL2tpLnsIfDefSubIdent TmnxDefSubIdSource
  tmnxL2tpLnsIfDefSubIdentString DisplayString
  tmnxL2tpLnsIfDefFilterProfile TNamedItemOrEmpty

TmnxL2tpLacMlpppBundleEntry  
SEQUENCE    
  tmnxL2tpLacMlpppBundleIndex Unsigned32
  tmnxL2tpLacMlpppBundleSvcId TmnxServId
  tmnxL2tpLacMlpppBundleFwdTuId TmnxL2tpTunnelId
  tmnxL2tpLacMlpppBundleUserName TmnxPppoeUserNameOrEmpty
  tmnxL2tpLacMlpppBundleLocEpClass TmnxMlpppEpClass
  tmnxL2tpLacMlpppBundleLocEpAddr OCTET STRING
  tmnxL2tpLacMlpppBundleRemEpClass TmnxMlpppEpClass
  tmnxL2tpLacMlpppBundleRemEpAddr OCTET STRING

TmnxL2tpLacMlpppLinkEntry  
SEQUENCE    
  tmnxL2tpLacMlpppLinkState TmnxL2tpSeOperState

TmnxL2tpApEntry  
SEQUENCE    
  tmnxL2tpApName TNamedItem
  tmnxL2tpApRowStatus RowStatus
  tmnxL2tpApLastMgmtChange TimeStamp
  tmnxL2tpApDescription TItemDescription
  tmnxL2tpApType BITS
  tmnxL2tpApServerVRtrID TmnxVRtrIDOrZero
  tmnxL2tpApServerAlgorithm TmnxSubRadServAlgorithm
  tmnxL2tpApServerRetry Unsigned32
  tmnxL2tpApServerSrcAddrType InetAddressType
  tmnxL2tpApServerSrcAddr InetAddress
  tmnxL2tpApServerTimeout Unsigned32
  tmnxL2tpApIncludeAttributes BITS
  tmnxL2tpApRequestScriptPlcy TNamedItemOrEmpty
  tmnxL2tpApNasPortIdPfixType TmnxSubNasPortPrefixType
  tmnxL2tpApNasPortIdPfixString DisplayString
  tmnxL2tpApNasPortIdSfixType TmnxSubNasPortSuffixType
  tmnxL2tpApNasPortTypeType TmnxSubNasPortTypeType
  tmnxL2tpApNasPortTypeValue Unsigned32
  tmnxL2tpApNasPortBitspec TmnxBinarySpecification

TmnxL2tpApServEntry  
SEQUENCE    
  tmnxL2tpApServIndex Unsigned32
  tmnxL2tpApServRowStatus RowStatus
  tmnxL2tpApServLastMgmtChange TimeStamp
  tmnxL2tpApServAddrType InetAddressType
  tmnxL2tpApServAddr InetAddress
  tmnxL2tpApServSecret DisplayString
  tmnxL2tpApServAcctPort Unsigned32
  tmnxL2tpApServOperState TmnxOperState

TmnxL2tpApServStatsEntry  
SEQUENCE    
  tmnxL2tpApServStatsTxRequests Counter32
  tmnxL2tpApServStatsRxResponses Counter32
  tmnxL2tpApServStatsReqTimeout Counter32
  tmnxL2tpApServStatsReqSendFail Counter32
  tmnxL2tpApServStatsReqPending Counter32
  tmnxL2tpApServStatsRespInvAuth Counter32
  tmnxL2tpApServStatsSendRetries Counter32

Defined Values

timetraL2tpMIBModule 1.3.6.1.4.1.6527.1.1.3.60
This document is the SNMP MIB module to manage and provision the Layer Two Tunneling Protocol (L2TP) for the Alcatel-Lucent SROS device. Copyright 2009-2012 Alcatel-Lucent. All rights reserved. Reproduction of this document is authorized on the condition that the foregoing copyright notice is included. This SNMP MIB module (Specification) embodies Alcatel-Lucent's proprietary intellectual property. Alcatel-Lucent retains all title and ownership in the Specification, including any revisions. Alcatel-Lucent grants all interested parties a non-exclusive license to use and distribute an unmodified copy of this Specification in connection with management of Alcatel-Lucent products, and without fee, provided this copyright notice and license appear on all copies. This Specification is supplied 'as is', and Alcatel-Lucent makes no warranty, either express or implied, as to the use, operation, condition, or performance of the Specification.
MODULE-IDENTITY    

tmnxL2tp 1.3.6.1.4.1.6527.3.1.2.60
OBJECT IDENTIFIER    

tmnxL2tpObjs 1.3.6.1.4.1.6527.3.1.2.60.1
OBJECT IDENTIFIER    

tmnxL2tpNotificationObjs 1.3.6.1.4.1.6527.3.1.2.60.2
OBJECT IDENTIFIER    

tmnxL2tpConformance 1.3.6.1.4.1.6527.3.1.1.60
OBJECT IDENTIFIER    

tmnxL2tpCompliances 1.3.6.1.4.1.6527.3.1.1.60.1
OBJECT IDENTIFIER    

tmnxL2tpGroups 1.3.6.1.4.1.6527.3.1.1.60.2
OBJECT IDENTIFIER    

tmnxL2tpNotifyPrefix 1.3.6.1.4.1.6527.3.1.3.60
OBJECT IDENTIFIER    

tmnxL2tpNotifications 1.3.6.1.4.1.6527.3.1.3.60.0
OBJECT IDENTIFIER    

tmnxL2tpVrtrObjs 1.3.6.1.4.1.6527.3.1.2.60.1.1
OBJECT IDENTIFIER    

tmnxL2tpTgObjs 1.3.6.1.4.1.6527.3.1.2.60.1.2
OBJECT IDENTIFIER    

tmnxL2tpTunnelObjs 1.3.6.1.4.1.6527.3.1.2.60.1.3
OBJECT IDENTIFIER    

tmnxL2tpPeerObjs 1.3.6.1.4.1.6527.3.1.2.60.1.4
OBJECT IDENTIFIER    

tmnxL2tpSessionObjs 1.3.6.1.4.1.6527.3.1.2.60.1.5
OBJECT IDENTIFIER    

tmnxL2tpLnsIsaObjs 1.3.6.1.4.1.6527.3.1.2.60.1.6
OBJECT IDENTIFIER    

tmnxL2tpLnsSvcObjs 1.3.6.1.4.1.6527.3.1.2.60.1.7
OBJECT IDENTIFIER    

tmnxL2tpMlpppObjs 1.3.6.1.4.1.6527.3.1.2.60.1.8
OBJECT IDENTIFIER    

tmnxL2tpAccountingObjs 1.3.6.1.4.1.6527.3.1.2.60.1.100
OBJECT IDENTIFIER    

tmnxL2tpVrtrCfgObjs 1.3.6.1.4.1.6527.3.1.2.60.1.1.1
OBJECT IDENTIFIER    

tmnxL2tpVrtrStatObjs 1.3.6.1.4.1.6527.3.1.2.60.1.1.2
OBJECT IDENTIFIER    

tmnxL2tpTableLastCh 1.3.6.1.4.1.6527.3.1.2.60.1.10
The value of tmnxL2tpTableLastCh indicates the sysUpTime at the time of the most recent management-initiated change to the tmnxL2tpTable.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpTable 1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2
A table that contains L2TP configuration information about virtual routers. Rows in this table can be created or deleted via SNMP operations. Rows in this table are automatically deleted when the corresponding row in the vRtrConfTable is deleted. The conceptual row that corresponds to the Base router instance, however, is automatically created by the system, and cannot be created or deleted via SNMP operations.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpEntry

tmnxL2tpEntry 1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1
L2TP specific information about a virtual router. Each entry represents a L2TP protocol instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpEntry  

tmnxL2tpLastMgmtChange 1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1.1
The value of tmnxL2tpLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpAdminState 1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1.2
The value of the object tmnxL2tpAdminState specifies the administrative state of this L2TP protocol instance.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxAdminState  

tmnxL2tpSessionLimit 1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1.3
The value of tmnxL2tpSessionLimit specifies the maximum number of sessions in this L2TP protocol instance.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxL2tpTunnelSessionLimit  

tmnxL2tpReceiveWindowSize 1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1.4
The value of tmnxL2tpReceiveWindowSize specifies the Receive Window Size in this L2TP protocol instance. The value '0' is not allowed.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxL2tpReceiveWindowSize  

tmnxL2tpRowStatus 1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1.5
The value of tmnxL2tpRowStatus specifies the row status of this row.
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

tmnxL2tpPeerAddrChangePlcy 1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1.6
The value of the object tmnxL2tpPeerAddrChangePlcy specifies what to do in case the system receives a L2TP response from another address than the one the request was sent to, for a tunnel in this L2TP protocol instance.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxL2tpPeerAddrChangePolicy  

tmnxL2tpAvpExclude 1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1.7
The value of the object tmnxL2tpAvpExclude specifies what AVP's (Attribute Value Pairs) to exclude from L2TP control messages related to a session in this L2TP protocol instance.
Status: current Access: read-write
OBJECT-TYPE    
  BITS callingNumber(0)  

tmnxL2tpAvpCallingNumberSpec 1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1.8
The value of the object tmnxL2tpAvpCallingNumberSpec specifies what string to put in the Calling Number AVP, for L2TP control messages related to a session in this L2TP protocol instance. This value is not applicable if the 'callingNumber' bit is set in the object tmnxL2tpAvpExclude. ::= 'S' | 'c' | 's' | 'r' 'S' - system name, the value of TIMETRA-CHASSIS-MIB::tmnxChassisName 'c' - Agent Circuit Id 's' - SAP ID, formatted as a character string 'r' - Agent Remote Id An empty string is not allowed. Example: '%S %s' means 'the system name, followed by a blank space, followed by the SAP ID formatted as a string'.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxAsciiSpecification  

tmnxL2tpAccountingPolicy 1.3.6.1.4.1.6527.3.1.2.60.1.1.1.2.1.10
The value of the object tmnxL2tpAccountingPolicy specifies the RADIUS accounting policy to use in this L2TP protocol instance. It refers to a conceptual row in the tmnxL2tpApTable. The value of tmnxL2tpAccountingPolicy can be overruled by a non-empty value of tmnxL2tpTgCfgAccountingPolicy or tmnxL2tpTuCfgAccountingPolicy.
Status: current Access: read-write
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxL2tpStatTable 1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1
A table that contains L2TP configuration information about virtual routers. The system automatically creates an entry in this table for each virtual router where L2TP is supported. Only the Base router supports L2TP.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpStatEntry

tmnxL2tpStatEntry 1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1
L2TP specific information about a virtual router. Each entry represents a L2TP protocol instance.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpStatEntry  

tmnxL2tpStatCleared 1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.1
The value of the object tmnxL2tpStatCleared indicates the value of sysUpTime when the system statistics were cleared. The value zero indicates that the system statistics have not been cleared since the last re-initialization of the local network management subsystem.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpStatTotalTunnels 1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.2
The value of tmnxL2tpStatTotalTunnels indicates the total number of tunnel set up attempts since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpStatFailedTunnels 1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.3
The value of tmnxL2tpStatFailedTunnels indicates the number of tunnels that failed to reach the established state since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpStatFailedTuAuth 1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.4
The value of tmnxL2tpStatFailedTuAuth indicates the number of tunnels that failed authentication since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpStatActiveTunnels 1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.5
The value of tmnxL2tpStatActiveTunnels indicates the number of tunnels currently established.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpStatTotalSessions 1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.6
The value of tmnxL2tpStatTotalSessions indicates the number of session creation attempts since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpStatFailedSessions 1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.7
The value of tmnxL2tpStatFailedSessions indicates the number of sessions that failed to reach the established state since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpStatActiveSessions 1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.8
The value of tmnxL2tpStatActiveSessions indicates the number of sessions currently established.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpStatCurrentTunnels 1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.9
The value of tmnxL2tpStatCurrentTunnels indicates the actual number of tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpStatCurrentSessions 1.3.6.1.4.1.6527.3.1.2.60.1.1.2.1.1.10
The value of tmnxL2tpStatCurrentSessions indicates the actual number of sessions.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTgCfgObjs 1.3.6.1.4.1.6527.3.1.2.60.1.2.1
OBJECT IDENTIFIER    

tmnxL2tpTgStatObjs 1.3.6.1.4.1.6527.3.1.2.60.1.2.2
OBJECT IDENTIFIER    

tmnxL2tpTgOpObjs 1.3.6.1.4.1.6527.3.1.2.60.1.2.3
OBJECT IDENTIFIER    

tmnxL2tpTgCfgTableLastCh 1.3.6.1.4.1.6527.3.1.2.60.1.11
The value of the object tmnxL2tpTgCfgTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpTgCfgTable.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpTgCfgTable 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2
The L2TP Tunnel configuration table contains objects to configure L2TP Tunnel Groups.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpTgCfgEntry

tmnxL2tpTgCfgEntry 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1
Each conceptual row represents a Layer Two Tunneling Protocol Tunnel Group. Entries in this table can be created or deleted via SNMP operations.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpTgCfgEntry  

tmnxL2tpTgCfgName 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.1
The value of the object tmnxL2tpTgCfgName specifies the string to identify this Layer Two Tunneling Protocol Tunnel Group.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpTunnelGroupName  

tmnxL2tpTgCfgRowStatus 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.2
The value of tmnxL2tpTgCfgRowStatus specifies the row status of this row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxL2tpTgCfgLastMgmtChange 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.3
The value of tmnxL2tpTgCfgLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpTgCfgDescription 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.4
The value of tmnxL2tpTgCfgDescription specifies the description of this Layer Two Tunneling Protocol Tunnel Group.
Status: current Access: read-create
OBJECT-TYPE    
  TItemDescription  

tmnxL2tpTgCfgAdminState 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.5
The value of tmnxL2tpTgCfgAdminState specifies the administrative state of this Layer Two Tunneling Protocol Tunnel Group.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAdminState  

tmnxL2tpTgCfgSecret 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.6
The value of the object tmnxL2tpTgCfgSecret specifies the password to be used for the authentication of the tunnels in this Layer Two Tunneling Protocol Tunnel Group. For any given tunnel in this group, the value of tmnxL2tpTgCfgSecret can be overruled with the value of tmnxL2tpTuCfgSecret. This object will always return an empty string on a read.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpAuthSecret  

tmnxL2tpTgCfgHelloInterval 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.7
The value of tmnxL2tpTgCfgHelloInterval specifies the time interval between two consecutive tunnel Hello messages. A value of '-1' specifies that the keepalive function is disabled. The value '-2' is not allowed because this is the widest scope for TmnxL2tpTunnelHelloInterval.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpTunnelHelloInterval  

tmnxL2tpTgCfgIdleTO 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.8
The value of tmnxL2tpTgCfgIdleTO specifies the period of time that an established tunnel with no active sessions will persist before being disconnected. A value of -1 leaves the tunnel up indefinitely. The value '-2' is not allowed because this is the widest scope for TmnxL2tpTunnelIdleTO.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpTunnelIdleTO  

tmnxL2tpTgCfgDestructTO 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.9
The value of tmnxL2tpTgCfgDestructTO specifies the period of time that the data of a disconnected tunnel will persist before being removed. The value '-2' is not allowed because this is the widest scope for TmnxL2tpTunnelDestructTO.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpTunnelDestructTO  

tmnxL2tpTgCfgMaxRetxEstab 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.10
The value of tmnxL2tpTgCfgMaxRetxEstab specifies the number of retries allowed for established tunnels before their control connection goes down. The value '-2' is not allowed because this is the widest scope.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpTunnelMaxRetx  

tmnxL2tpTgCfgMaxRetxNotEstab 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.11
The value of tmnxL2tpTgCfgMaxRetxNotEstab specifies the number of retries allowed for unestablished tunnels before their control connection goes down. The value '-2' is not allowed because this is the widest scope.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpTunnelMaxRetx  

tmnxL2tpTgCfgSessionLimit 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.12
The value of tmnxL2tpTgCfgSessionLimit specifies the maximum number of sessions in this Layer Two Tunneling Protocol Tunnel Group.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpTunnelSessionLimit  

tmnxL2tpTgCfgAvpHiding 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.13
The value of the object tmnxL2tpTgCfgAvpHiding specifies the method to be used for the authentication of the tunnels in this Layer Two Tunneling Protocol Tunnel Group. The value 'default' is not allowed because this is the widest scope for TmnxL2tpAvpHidingMode.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpAvpHidingMode  

tmnxL2tpTgCfgSessionAssignMethod 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.14
The value of the object tmnxL2tpTgCfgSessionAssignMethod specifies the method to be used for the authentication of the tunnels in this Layer Two Tunneling Protocol Tunnel Group
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpSessionAssignMethod  

tmnxL2tpTgCfgLocalName 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.15
The value of the object tmnxL2tpTgCfgLocalName specifies the host name used by this system for the tunnels in this Layer Two Tunneling Protocol Tunnel Group during the authentication phase of tunnel establishment. This object is related to the RADIUS attribute Tunnel-Client-Auth-ID. It can be used to distinguish tunnels. An empty string specifies that the system name (SNMPv2-MIB::sysName) is used.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpHostNameOrEmpty  

tmnxL2tpTgCfgDoChallenge 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.16
The value of the object tmnxL2tpTgCfgDoChallenge specifies when challenge-response is to be used for the authentication of the tunnels in this Layer Two Tunneling Protocol Tunnel Group. The value 'default' is not allowed because this is the widest scope for TmnxL2tpDoChallenge.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpDoChallenge  

tmnxL2tpTgCfgReceiveWindowSize 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.17
The value of the object tmnxL2tpTgCfgReceiveWindowSize specifies the Receive Window Size of the tunnels in this L2TP Tunnel Group. The value zero specifies that the value must be set to the actual value of the object tmnxL2tpReceiveWindowSize.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpReceiveWindowSize  

tmnxL2tpTgCfgIsaGrpId 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.19
The value of tmnxL2tpTgCfgIsaGrpId specifies the L2TP Integrated Service Adaptor group for the tunnels in this L2TP Tunnel Group.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpIsaGrpIdOrZero  

tmnxL2tpTgCfgAddrType 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.20
The value of tmnxL2tpTgCfgAddrType specifies the address type of tmnxL2tpTgCfgAddr.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

tmnxL2tpTgCfgAddr 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.21
The value of tmnxL2tpTgCfgAddr specifies the local IP address of the tunnels in this L2TP Tunnel Group.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress Size(0|4|16)  

tmnxL2tpTgCfgLoadBalanceMethod 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.25
The value of the object tmnxL2tpTgCfgLoadBalanceMethod specifies the method to be used for load-balancing sessions across ISA MDA in this Layer Two Tunneling Protocol Tunnel Group. The value 'default' is not allowed.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpIsaMdaLoadBalanceMethod  

tmnxL2tpTgCfgAccountingPolicy 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.2.1.26
The value of the object tmnxL2tpTgCfgAccountingPolicy specifies the RADIUS accounting policy to be used in this Layer Two Tunneling Protocol Tunnel Group. It refers to a conceptual row in the tmnxL2tpApTable. The value of tmnxL2tpTgCfgAccountingPolicy can be overruled by a non-empty value of tmnxL2tpTuCfgAccountingPolicy. An empty string specifies that the value of tmnxL2tpAccountingPolicy must be used.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxL2tpLnsTgPppTableLastCh 1.3.6.1.4.1.6527.3.1.2.60.1.18
The value of the object tmnxL2tpLnsTgPppTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpLnsTgPppTable.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpLnsTgPppTable 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3
The L2TP Tunnel configuration table contains objects to configure PPP (Point to Point Protocol) on L2TP LNS Tunnel Groups. Entries in this table are automatically created and deleted by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpLnsTgPppEntry

tmnxL2tpLnsTgPppEntry 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1
Each conceptual row represents PPP information about a Layer Two Tunneling Protocol LNS Tunnel Group.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpLnsTgPppEntry  

tmnxL2tpLnsTgPppLastMgmtChange 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.1
The value of tmnxL2tpLnsTgPppLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpLnsTgPppAuthPlcy 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.2
The value of the object tmnxL2tpLnsTgPppAuthPlcy specifies the authentication policy used by this system for the tunnels in this L2TP LNS Tunnel Group during the authentication phase of tunnel establishment. An empty string specifies that no authentication policy is used.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxL2tpLnsTgPppAuthProtocol 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.3
The value of the object tmnxL2tpLnsTgPppAuthProtocol specifies for the tunnels in this L2TP LNS Tunnel Group what PPP authentication protocol(s) will be negotiated during the LCP phase. The value 'default' is not allowed.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpPppAuthentication  

tmnxL2tpLnsTgPppUserDb 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.4
The value of the object tmnxL2tpLnsTgPppUserDb specifies the local user database to use for PADI or PPP PAP/CHAP based authentication during the authentication phase of tunnel establishment. An empty string specifies that no local user database is used.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxL2tpLnsTgPppDefaultService 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.5
The value of tmnxL2tpLnsTgPppDefaultService specifies the service ID of the service where the PPP sessions are established when the authentication server does not specify the service ID.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxServId  

tmnxL2tpLnsTgPppDefaultGroupIf 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.6
The value of tmnxL2tpLnsTgPppDefaultGroupIf specifies the group interface where the PPP sessions are established when the authentication server does not specify the group interface.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxL2tpLnsTgPppProxyLcp 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.7
The value of tmnxL2tpLnsTgPppProxyLcp specifies if this system re-uses the result of the Link Control Protocol (LCP) negotiation done by the proxy (LAC). If the value of this object is 'always', the Proxy LCP AVPs received from the LAC are used to initiate the LCP on this system. If the value of this object is 'never', this system restarts the LCP negotiation with the remote system.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAlwaysOrNever  

tmnxL2tpLnsTgPppProxyAuth 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.8
The value of tmnxL2tpLnsTgPppProxyAuth specifies if this system re-uses the authentication done by the proxy (LAC). If the value of this object is 'always', the Authentication AVPs received from the LAC are accepted. If the value of this object is 'never', this system restarts the authentication of the remote system.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAlwaysOrNever  

tmnxL2tpLnsTgPppMtu 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.9
The value of tmnxL2tpLnsTgPppMtu specifies the MTU (Maximum Transmission Unit) for the tunnels in this L2TP LNS Tunnel Group. The value zero is not allowed.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpPppMtu  

tmnxL2tpLnsTgPppLcpKaInterval 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.10
The value of tmnxL2tpLnsTgPppLcpKaInterval specifies for the tunnels in this L2TP LNS Tunnel Group the time interval in seconds at which LCP echo requests are transmitted. The value '0' is not allowed.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpLcpKaInterval  

tmnxL2tpLnsTgPppLcpKaHoldUp 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.11
The value of tmnxL2tpLnsTgPppLcpKaHoldUp specifies for the tunnels in this L2TP LNS Tunnel Group how many LCP keepalive messages can be missed before the related session is brought down. The value '0' is not allowed.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpLcpKaHoldUpMplier  

tmnxL2tpLnsTgPppIpcpSubnetNeg 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.3.1.13
The value of tmnxL2tpLnsTgPppIpcpSubnetNeg specifies for the tunnels in this L2TP LNS Tunnel Group if IPCP subnet negotiation is enabled.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAlwaysOrNever  

tmnxL2tpTgMlpppTable 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4
The L2TP Tunnel configuration table contains objects to configure MLPPP (Multi Link Point to Point Protocol) on L2TP Tunnel Groups. Entries in this table are automatically created and deleted by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpTgMlpppEntry

tmnxL2tpTgMlpppEntry 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1
Each conceptual row represents MLPPP information about a Layer Two Tunneling Protocol LNS Tunnel Group.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpTgMlpppEntry  

tmnxL2tpTgMlpppLastMgmtChange 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1.1
The value of tmnxL2tpTgMlpppLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpTgMlpppAdminState 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1.2
The value of tmnxL2tpTgMlpppAdminState specifies the administrative state of MLPPP for this Layer Two Tunneling Protocol Tunnel Group.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAdminState  


tmnxL2tpTgMlpppInterleave 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1.4
The value of tmnxL2tpTgMlpppInterleave specifies if this system applies Link Fragmentation and Interleaving to the traffic sent from the LNS to the LAC. If the value of this object is 'always', downstream traffic is fragmented and interleaved, meaning that (non-fragmented) realtime traffic is interleaved with fragments of non-realtime traffic. If the value of this object is 'never', downstream traffic is only fragmented but not reordered according to priority. The value of this object is only relevant for tunnels where this system performs the LNS role.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAlwaysOrNever  

tmnxL2tpTgMlpppMaxFragDelay 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1.5
The value of tmnxL2tpTgMlpppMaxFragDelay specifies the maximum delay for fragments for the tunnels in this L2TP LNS Tunnel Group. The value zero means 'no fragmentation'. The value of this object is only relevant for tunnels where this system performs the LNS role.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpMlpppMaxFragDelay  

tmnxL2tpTgMlpppReassemblyTo 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1.6
The value of tmnxL2tpTgMlpppReassemblyTo specifies the reassembly timeout for fragments for the tunnels in this L2TP LNS Tunnel Group. The value zero is not allowed. The value of this object is only relevant for tunnels where this system performs the LNS role.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpMlpppReassemblyTimeout 100 | 1000  

tmnxL2tpTgMlpppShortSeqNumberRx 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1.7
The value of tmnxL2tpTgMlpppShortSeqNumberRx specifies if this system requests to receive short sequence numbers from the peer. If the value of this object is 'always', this system includes the Short Sequence Number Header Format Option in its LCP configuration options. If the value of this object is 'never', this system does not includes the Short Sequence Number Header Format Option in its LCP configuration options. The value of this object is only relevant for tunnels where this system performs the LNS role.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAlwaysOrNever  

tmnxL2tpTgMlpppEpClass 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1.8
The value of tmnxL2tpTgMlpppEpClass specifies the type of endpoint. If the value of 'tmnxL2tpTgMlpppEpClass' is equal to 'ipv4Address', the address for the MLPPP Endpoint Discriminator Option is taken from tmnxL2tpTgMlpppEpIpv4Address. If the value of 'tmnxL2tpTgMlpppEpClass' is equal to 'macAddress', the address for the MLPPP Endpoint Discriminator Option is taken from tmnxL2tpTgMlpppEpMacAddress. If the value of 'tmnxL2tpTgMlpppEpClass' is equal to 'default', the MLPPP Endpoint Discriminator Option must not be transmitted. A value other than 'default' is only relevant for tunnels where this system performs the LNS role.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpMlpppEndpointClass  

tmnxL2tpTgMlpppEpIpv4Address 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1.9
The value of tmnxL2tpTgMlpppEpIpv4Address specifies the class 2 address to use in the MLPPP Endpoint Discriminator Option. While the value of tmnxL2tpTgMlpppEpClass is equal to 'ipv4Address', a value of all zeroes specifies that the system IP address be used; otherwise, it means that no address is specified.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressIPv4  

tmnxL2tpTgMlpppEpMacAddress 1.3.6.1.4.1.6527.3.1.2.60.1.2.1.4.1.10
The value of tmnxL2tpTgMlpppEpMacAddress specifies the class 3 address to use in the MLPPP Endpoint Discriminator Option. While the value of tmnxL2tpTgMlpppEpClass is equal to 'macAddress', a value of all zeroes specifies that the system MAC address be used; otherwise, it means that no address is specified.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

tmnxL2tpTgStatTable 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1
The tmnxL2tpTgStatTable contains status and statistics information about Layer Two Tunneling Protocol Tunnel Groups. The tmnxL2tpTgStatTable has an entry for each L2TP Tunnel Group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpTgStatEntry

tmnxL2tpTgStatEntry 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1
Each row entry contains status and statistics about an L2TP tunnel group. Rows are created or removed automatically by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpTgStatEntry  

tmnxL2tpTgStatName 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.1
The value of the object tmnxL2tpTgStatName indicates the string to identify this Layer Two Tunneling Protocol Tunnel Group.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpTunnelGroupName  

tmnxL2tpTgStatState 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.2
The value of tmnxL2tpTgStatState indicates the operational state of this Layer Two Tunneling Protocol Tunnel Group.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpTgOperState  

tmnxL2tpTgStatCleared 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.3
The value of the object tmnxL2tpTgStatCleared indicates the value of sysUpTime when the tunnel group statistics were cleared. The value zero indicates that the statistics have not been cleared since the last re-initialization of the local network management subsystem.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpTgStatTotalTunnels 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.4
The value of tmnxL2tpTgStatTotalTunnels indicates the total number of tunnel set up attempts in this tunnel group since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpTgStatFailedTunnels 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.5
The value of tmnxL2tpTgStatFailedTunnels indicates the number of tunnels in this tunnel group that failed to reach the established state since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpTgStatFailedTuAuth 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.6
The value of tmnxL2tpTgStatFailedTuAuth indicates the number of tunnels in this tunnel group that failed authentication since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpTgStatActiveTunnels 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.7
The value of tmnxL2tpTgStatActiveTunnels indicates the number of tunnels currently established in this tunnel group.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTgStatTunnels 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.8
The value of tmnxL2tpTgStatTunnels indicates the actual number of tunnels in this tunnel group.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTgStatTotalSessions 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.9
The value of tmnxL2tpTgStatTotalSessions indicates the number of session creation attempts in this tunnel group since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpTgStatFailedSessions 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.10
The value of tmnxL2tpTgStatFailedSessions indicates the number of sessions in this tunnel group that failed to reach the established state since the last re-initialization of the local network management subsystem, or the last time the system statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpTgStatActiveSessions 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.11
The value of tmnxL2tpTgStatActiveSessions indicates the number of sessions currently established in this tunnel group.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTgStatSessions 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.12
The value of tmnxL2tpTgStatSessions indicates the actual number of sessions in this tunnel group.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTgStatControlRxOctets 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.13
The value of tmnxL2tpTgStatControlRxOctets indicates the number of control channel octets received by the current tunnels in this tunnel group.
Status: current Access: read-only
OBJECT-TYPE    
  CounterBasedGauge64  

tmnxL2tpTgStatControlRxOctetsLw 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.14
The value of tmnxL2tpTgStatControlRxOctetsLw indicates the lower 32-bits word of the value of tmnxL2tpTgStatControlRxOctets.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTgStatControlRxOctetsHw 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.15
The value of tmnxL2tpTgStatControlRxOctetsHw indicates the higher 32-bits word of the value of tmnxL2tpTgStatControlRxOctets.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTgStatControlRxPkts 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.16
The value of tmnxL2tpTgStatControlRxPkts indicates the accumulated number of control packets received by the current tunnels in this tunnel group.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTgStatControlTxOctets 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.17
The value of tmnxL2tpTgStatControlTxOctets indicates the accumulated number of control channel octets that were transmitted to the current tunnel endpoints in this tunnel group.
Status: current Access: read-only
OBJECT-TYPE    
  CounterBasedGauge64  

tmnxL2tpTgStatControlTxOctetsLw 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.18
The value of tmnxL2tpTgStatControlTxOctetsLw indicates the lower 32-bits word of the value of tmnxL2tpTgStatControlTxOctets.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTgStatControlTxOctetsHw 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.19
The value of tmnxL2tpTgStatControlTxOctetsHw indicates the higher 32-bits word of the value of tmnxL2tpTgStatControlTxOctets.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTgStatControlTxPkts 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.20
The value of tmnxL2tpTgStatControlTxPkts indicates the accumulated number of control packets that were transmitted to the current tunnel endpoints in this tunnel group.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTgStatErrorTxPkts 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.21
The value of tmnxL2tpTgStatErrorTxPkts indicates the accumulated number of packet transmission errors on the current tunnels in this tunnel group.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTgStatErrorRxPkts 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.22
The value of tmnxL2tpTgStatErrorRxPkts indicates the accumulated number of errored packets that were received on the current tunnels in this tunnel group.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTgStatSessionLimit 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.23
The value of tmnxL2tpTgStatSessionLimit indicates the actual session limit of this tunnel group.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTgStatSeAssignMethod 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.1.1.24
The value of the object tmnxL2tpTgStatSeAssignMethod indicates the latest actual method used for the authentication of the tunnels in this Layer Two Tunneling Protocol Tunnel Group. Note that the next tunnel that will be set up in this L2TP tunnel group may or may not use the same method, since the configuration of the RADIUS server may have changed in the meantime.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpSessionAssignMethod  

tmnxL2tpTgTuTable 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.2
The tmnxL2tpTgTuTable contains the set of active tunnels for each L2TP Tunnel Group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpTgTuEntry

tmnxL2tpTgTuEntry 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.2.1
Each row entry contains a tunnel identifier of an L2TP tunnel group. Rows are created or removed automatically by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpTgTuEntry  

tmnxL2tpTgTuId 1.3.6.1.4.1.6527.3.1.2.60.1.2.2.2.1.1
The value of the object tmnxL2tpTgTuId indicates the local identifier of a Layer Two Tunneling Protocol Tunnel. In L2TP version 2, it is the 16-bit tunnel ID. In L2TP version 3, it is the 32-bit control connection ID.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpConnectionId  

tmnxL2tpTgDrainTable 1.3.6.1.4.1.6527.3.1.2.60.1.2.3.1
The tmnxL2tpTgDrainTable has an entry for each active Layer Two Tunneling Protocol Tunnel Group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpTgDrainEntry

tmnxL2tpTgDrainEntry 1.3.6.1.4.1.6527.3.1.2.60.1.2.3.1.1
Each conceptual row presents an operations interface to drain a Layer Two Tunneling Protocol Tunnel Group. After a successful drain operation, the value of the object tmnxL2tpTgStatState of this tunnel group is equal to 'drain', and the value of the object tmnxL2tpTuStatusState is equal to 'draining' for all the tunnels of this L2TP tunnel group; none of these tunnels accept or establish new connections, while existing connections are timing out. Entries in this table are created and destroyed by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpTgDrainEntry  

tmnxL2tpTgDrain 1.3.6.1.4.1.6527.3.1.2.60.1.2.3.1.1.1
Setting this object to 'drain (0)' triggers an attempt to drain this L2TP tunnel group. Setting it to 'stopDrain (1)' stops the draining. Reading this object returns the value 'notApplicable'.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxL2tpActionTypeDrain  

tmnxL2tpTuCfgObjs 1.3.6.1.4.1.6527.3.1.2.60.1.3.1
OBJECT IDENTIFIER    

tmnxL2tpTuStatObjs 1.3.6.1.4.1.6527.3.1.2.60.1.3.2
OBJECT IDENTIFIER    

tmnxL2tpTuOpObjs 1.3.6.1.4.1.6527.3.1.2.60.1.3.3
OBJECT IDENTIFIER    

tmnxL2tpTuCfgTableLastCh 1.3.6.1.4.1.6527.3.1.2.60.1.12
The value of the object tmnxL2tpTuCfgTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpTuCfgTable.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpTuCfgTable 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2
The L2TP Tunnel configuration table contains objects to configure L2TP Tunnels.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpTuCfgEntry

tmnxL2tpTuCfgEntry 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1
Each conceptual row represents a Layer Two Tunneling Protocol Tunnel. Entries in this table can be created or deleted via SNMP operations.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpTuCfgEntry  

tmnxL2tpTuCfgName 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.1
The value of the object tmnxL2tpTuCfgName specifies the name of this Layer Two Tunneling Protocol Tunnel.
Status: current Access: not-accessible
OBJECT-TYPE    
  TNamedItem  

tmnxL2tpTuCfgRowStatus 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.2
The value of tmnxL2tpTuCfgRowStatus specifies the row status of this row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxL2tpTuCfgLastMgmtChange 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.3
The value of tmnxL2tpTuCfgLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpTuCfgDescription 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.4
The value of tmnxL2tpTuCfgDescription specifies the description of this Layer Two Tunneling Protocol Tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  TItemDescription  

tmnxL2tpTuCfgAdminState 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.5
The value of tmnxL2tpTuCfgAdminState specifies the administrative state of this Layer Two Tunneling Protocol Tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAdminState  

tmnxL2tpTuCfgPreference 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.6
The value of tmnxL2tpTuCfgPreference specifies the preference of this Layer Two Tunneling Protocol Tunnel. The value '0' corresponds to the highest preference.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpTunnelPreference  

tmnxL2tpTuCfgPeerAddrType 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.7
The value of tmnxL2tpTuCfgPeerAddrType specifies the address type of tmnxL2tpTuCfgPeerAddr.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

tmnxL2tpTuCfgPeerAddr 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.8
The value of tmnxL2tpTuCfgPeerAddr specifies the IP address of the peer.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress Size(0|4|16)  

tmnxL2tpTuCfgAddrType 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.9
The value of tmnxL2tpTuCfgAddrType specifies the address type of tmnxL2tpTuCfgAddr. The value 'unknown' specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgAddrType.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

tmnxL2tpTuCfgAddr 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.10
The value of tmnxL2tpTuCfgAddr specifies the local IP address of this Layer Two Tunneling Protocol Tunnel. The value ''H specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgAddr.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress Size(0|4|16)  

tmnxL2tpTuCfgLocalName 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.11
The value of the object tmnxL2tpTuCfgLocalName specifies the host name used by this system during the authentication phase of tunnel establishment. This object is related to the RADIUS attribute Tunnel-Client-Auth-ID. It can be used to distinguish tunnels. An empty string specifies that the value of the object tmnxL2tpTgCfgLocalName is used.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpHostNameOrEmpty  

tmnxL2tpTuCfgRemoteName 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.12
The value of the object tmnxL2tpTuCfgRemoteName specifies a string to be compared to the host name used by the tunnel peer during the authentication phase of tunnel establishment. This object is related to the RADIUS attribute Tunnel-Server-Auth-ID. It can be used to distinguish tunnels.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpHostNameOrEmpty  

tmnxL2tpTuCfgSecret 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.13
The value of the object tmnxL2tpTuCfgSecret specifies the password to be used for the authentication of this Layer Two Tunneling Protocol Tunnel. This value overrules the value of the object tmnxL2tpTgCfgSecret of the tunnel group this tunnel belongs to. This object will always return an empty string on a read.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpAuthSecret  

tmnxL2tpTuCfgHelloInterval 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.14
The value of tmnxL2tpTuCfgHelloInterval specifies the time interval between two consecutive tunnel Hello messages. A value of '-1' specifies that the keepalive function is disabled. A value of '-2' specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgHelloInterval.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpTunnelHelloInterval  

tmnxL2tpTuCfgIdleTO 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.15
The value of tmnxL2tpTuCfgIdleTO specifies the period of time that an established tunnel with no active sessions will persist before being disconnected. A value of -1 leaves the tunnel up indefinitely. A value of '-2' specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgIdleTO.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpTunnelIdleTO  

tmnxL2tpTuCfgDestructTO 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.16
The value of tmnxL2tpTuCfgDestructTO specifies the period of time that data of a disconnected tunnel will persist before being removed. A value of '-2' specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgDestructTO.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpTunnelDestructTO  

tmnxL2tpTuCfgMaxRetxEstab 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.17
The value of tmnxL2tpTuCfgMaxRetxEstab specifies the number of retries allowed for this Layer Two Tunneling Protocol Tunnel while it is established, before its control connection goes down.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpTunnelMaxRetx  

tmnxL2tpTuCfgMaxRetxNotEstab 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.18
The value of tmnxL2tpTuCfgMaxRetxNotEstab specifies the number of retries allowed for this Layer Two Tunneling Protocol Tunnel while it is unestablished, before its control connection goes down.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpTunnelMaxRetx  

tmnxL2tpTuCfgSessionLimit 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.19
The value of tmnxL2tpTuCfgSessionLimit specifies the maximum number of sessions allowed in this Layer Two Tunneling Protocol Tunnel.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpTunnelSessionLimit  

tmnxL2tpTuCfgAvpHiding 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.20
The value of tmnxL2tpTuCfgAvpHiding specifies when the H bit in the header of each Attribute Value Pair (AVP) is set for the L2TP control messages related to this Layer Two Tunneling Protocol Tunnel. The value 'default' specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgAvpHiding of the tunnel group this tunnel belongs to.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpAvpHidingMode  

tmnxL2tpTuCfgAutoEstab 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.21
The value of tmnxL2tpTuCfgAutoEstab specifies if this Layer Two Tunneling Protocol Tunnel is to be set up automatically by the system.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

tmnxL2tpTuCfgDoChallenge 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.22
The value of tmnxL2tpTuCfgDoChallenge specifies when challenge-response is to be used for the authentication of this Layer Two Tunneling Protocol Tunnel. The value 'default' specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgDoChallenge of the tunnel group this tunnel belongs to.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpDoChallenge  

tmnxL2tpTuCfgReceiveWindowSize 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.23
The value of tmnxL2tpTuCfgReceiveWindowSize specifies the Receive Window Size for this Layer Two Tunneling Protocol Tunnel. The value zero specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgReceiveWindowSize.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpReceiveWindowSize  

tmnxL2tpTuCfgIsaGrpId 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.24
The value of tmnxL2tpTuCfgDoChallenge specifies the L2TP Integrated Service Adaptor group of this Layer Two Tunneling Protocol Tunnel. The value zero specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgIsaGrpId of the tunnel group this tunnel belongs to.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpIsaGrpIdOrZero  

tmnxL2tpTuCfgLoadBalanceMethod 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.30
The value of the object tmnxL2tpTuCfgLoadBalanceMethod specifies the method to be used for load-balancing sessions across ISA MDA in this Layer Two Tunneling Protocol Tunnel. The value 'default' specifies that the value must be set to the actual value of the object tmnxL2tpTgCfgLoadBalanceMethod of the tunnel group this tunnel belongs to.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpIsaMdaLoadBalanceMethod  

tmnxL2tpTuCfgAccountingPolicy 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.2.1.31
The value of the object tmnxL2tpTuCfgAccountingPolicy specifies the RADIUS accounting policy to be used in this Layer Two Tunneling Protocol Tunnel. It refers to a conceptual row in the tmnxL2tpApTable. An empty string specifies that the value of tmnxL2tpTgCfgAccountingPolicy must be used
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxL2tpLnsTuPppTableLastCh 1.3.6.1.4.1.6527.3.1.2.60.1.19
The value of the object tmnxL2tpLnsTuPppTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpLnsTuPppTable.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpLnsTuPppTable 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3
The L2TP Tunnel configuration table contains objects to configure PPP (Point to Point Protocol) on L2TP LNS Tunnels. Entries in this table are automatically created and deleted by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpLnsTuPppEntry

tmnxL2tpLnsTuPppEntry 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1
Each conceptual row represents PPP information about a Layer Two Tunneling Protocol LNS Tunnel configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpLnsTuPppEntry  

tmnxL2tpLnsTuPppLastMgmtChange 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.1
The value of tmnxL2tpLnsTuPppLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpLnsTuPppAuthPlcy 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.2
The value of the object tmnxL2tpLnsTuPppAuthPlcy specifies the authentication policy used by this system during the authentication phase of session establishment. An empty string specifies that the actual value must be used of the object tmnxL2tpLnsTgPppAuthPlcy of the tunnel group this tunnel configuration belongs to.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxL2tpLnsTuPppAuthProtocol 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.3
The value of tmnxL2tpLnsTuPppAuthProtocol specifies what PPP authentication protocol(s) will be negotiated during the LCP phase for the sessions of this tunnel. The value zero specifies that the actual value must be used of the object tmnxL2tpLnsTgPppAuthProtocol.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpPppAuthentication  

tmnxL2tpLnsTuPppUserDb 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.4
The value of the object tmnxL2tpLnsTuPppUserDb specifies the local user database to use for PADI or PPP PAP/CHAP based authentication during the authentication phase of session establishment. An empty string specifies that the actual value must be used of the object tmnxL2tpLnsTgPppUserDb of the tunnel group this tunnel configuration belongs to.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxL2tpLnsTuPppDefaultService 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.5
The value of tmnxL2tpLnsTuPppDefaultService specifies the service ID of the service where the PPP sessions are established when the authentication server does not specify the service ID. The value zero specifies that that the actual value must be used of the object tmnxL2tpLnsTgPppDefaultService. If the value of tmnxL2tpLnsTuPppDefaultService is equal to zero, the value of tmnxL2tpLnsTuPppDefaultGroupIf must also be equal to zero.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxServId  

tmnxL2tpLnsTuPppDefaultGroupIf 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.6
The value of tmnxL2tpLnsTuPppDefaultGroupIf specifies the group interface where the PPP sessions are established when the authentication server does not specify the group interface. The empty string specifies that the actual value must be used of the object tmnxL2tpLnsTgPppDefaultGroupIf. If the value of tmnxL2tpLnsTuPppDefaultGroupIf is equal to zero, the value of tmnxL2tpLnsTuPppDefaultService must also be equal to zero.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxL2tpLnsTuPppProxyLcp 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.7
The value of tmnxL2tpLnsTuPppProxyLcp specifies if this system re-uses the result of the Link Control Protocol (LCP) negotiation done by the proxy (LAC). If the value of this object is 'always', the Proxy LCP AVPs received from the LAC are used to initiate the LCP on this system. If the value of this object is 'never', this system restarts the LCP negotiation with the remote system. The value 'default' specifies that the actual value must be used of the object tmnxL2tpLnsTgPppProxyLcp.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAlwaysNeverOrDefault  

tmnxL2tpLnsTuPppProxyAuth 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.8
The value of tmnxL2tpLnsTuPppProxyAuth specifies if this system re-uses the authentication done by the proxy (LAC). If the value of this object is 'always', the Authentication AVPs received from the LAC are accepted. If the value of this object is 'never', this system restarts the authentication of the remote system. The value 'default' specifies that the actual value must be used of the object tmnxL2tpLnsTgPppProxyAuth.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAlwaysNeverOrDefault  

tmnxL2tpLnsTuPppMtu 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.9
The value of tmnxL2tpLnsTuPppMtu specifies the MTU (Maximum Transmission Unit) for this tunnel. The value zero specifies that the actual value must be used of the object tmnxL2tpLnsTgPppMtu.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpPppMtu  

tmnxL2tpLnsTuPppLcpKaInterval 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.10
The value of tmnxL2tpLnsTuPppLcpKaInterval specifies the time interval in seconds at which LCP echo requests are transmitted for this tunnel. The value zero specifies that the actual value must be used of the object tmnxL2tpLnsTgPppLcpKaInterval. If the value of tmnxL2tpLnsTuPppLcpKaInterval is equal to zero, the value of tmnxL2tpLnsTuPppLcpKaHoldUp must also be equal to zero.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpLcpKaInterval  

tmnxL2tpLnsTuPppLcpKaHoldUp 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.11
The value of tmnxL2tpLnsTuPppLcpKaHoldUp specifies how many LCP keepalive messages can be missed before the related session is brought down. The value zero specifies that the actual value must be used of the object tmnxL2tpLnsTgPppLcpKaHoldUp. If the value of tmnxL2tpLnsTuPppLcpKaHoldUp is equal to zero, the value of tmnxL2tpLnsTuPppLcpKaInterval must also be equal to zero.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpLcpKaHoldUpMplier  

tmnxL2tpLnsTuPppIpcpSubnetNeg 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.3.1.13
The value of tmnxL2tpLnsTuPppIpcpSubnetNeg specifies if IPCP subnet negotiation is enabled.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAlwaysNeverOrDefault  

tmnxL2tpTuMlpppTable 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4
The L2TP Tunnel configuration table contains objects to configure MLPPP on L2TP Tunnels. Entries in this table are automatically created and deleted by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpTuMlpppEntry

tmnxL2tpTuMlpppEntry 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1
Each conceptual row represents MLPPP information about a Layer Two Tunneling Protocol LNS Tunnel configuration.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpTuMlpppEntry  

tmnxL2tpTuMlpppLastMgmtChange 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1.1
The value of tmnxL2tpTuMlpppLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpTuMlpppAdminState 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1.2
The value of tmnxL2tpTuMlpppAdminState specifies the administrative state of MLPPP for this Layer Two Tunneling Protocol Tunnel. The value 'noop' specifies that the actual value must be used of the object tmnxL2tpTgMlpppAdminState of the tunnel group this tunnel configuration belongs to.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAdminState  


tmnxL2tpTuMlpppInterleave 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1.4
The value of tmnxL2tpTuMlpppInterleave specifies if this system applies Link Fragmentation and Interleaving to the traffic sent from the LNS to the LAC. If the value of this object is 'always', downstream traffic is fragmented and interleaved, meaning that (non-fragmented) realtime traffic is interleaved with fragments of non-realtime traffic. If the value of this object is 'never', downstream traffic is only fragmented but not reordered according to priority. The value 'default' specifies that the actual value must be used of the object tmnxL2tpTgMlpppInterleave. The value of this object is only relevant for tunnels where this system performs the LNS role.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAlwaysNeverOrDefault  

tmnxL2tpTuMlpppMaxFragDelay 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1.5
The value of tmnxL2tpTuMlpppMaxFragDelay specifies the maximum delay of fragments for this L2TP Tunnel. The value zero specifies that the actual value must be used of the object tmnxL2tpTgMlpppMaxFragDelay of the tunnel group this tunnel configuration belongs to. The value of this object is only relevant for tunnels where this system performs the LNS role.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpMlpppMaxFragDelay  

tmnxL2tpTuMlpppReassemblyTo 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1.6
The value of tmnxL2tpTuMlpppReassemblyTo specifies the reassembly timeout for fragments for this L2TP Tunnel. The value zero specifies that the actual value must be used of the object tmnxL2tpTgMlpppReassemblyTo of the tunnel group this tunnel configuration belongs to. The value of this object is only relevant for tunnels where this system performs the LNS role.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpMlpppReassemblyTimeout  

tmnxL2tpTuMlpppShortSeqNumberRx 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1.7
The value of tmnxL2tpTuMlpppShortSeqNumberRx specifies if this system requests to receive short sequence numbers from the peer. If the value of this object is 'always', this system includes the Short Sequence Number Header Format Option in its LCP configuration options. If the value of this object is 'never', this system does not includes the Short Sequence Number Header Format Option in its LCP configuration options. The value of this object is only relevant for tunnels where this system performs the LNS role.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAlwaysNeverOrDefault  

tmnxL2tpTuMlpppEpClass 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1.8
The value of tmnxL2tpTuMlpppEpClass specifies the type of endpoint. If the value of 'tmnxL2tpTuMlpppEpClass' is equal to 'ipv4Address', the address for the MLPPP Endpoint Discriminator Option is taken from tmnxL2tpTuMlpppEpIpv4Address. If the value of 'tmnxL2tpTuMlpppEpClass' is equal to 'macAddress', the address for the MLPPP Endpoint Discriminator Option is taken from tmnxL2tpTuMlpppEpMacAddress. The value 'default' specifies that the actual value must be used of the object tmnxL2tpTgMlpppEpClass of the tunnel group this tunnel configuration belongs to. A value other than 'default' is only relevant for tunnels where this system performs the LNS role.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxL2tpMlpppEndpointClass  

tmnxL2tpTuMlpppEpIpv4Address 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1.9
The value of tmnxL2tpTuMlpppEpIpv4Address specifies the class 2 address to use in the MLPPP Endpoint Discriminator Option. While the value of tmnxL2tpTuMlpppEpClass is equal to 'ipv4Address', a value of all zeroes specifies that the system IP address be used; otherwise, it means that no address is specified.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressIPv4  

tmnxL2tpTuMlpppEpMacAddress 1.3.6.1.4.1.6527.3.1.2.60.1.3.1.4.1.10
The value of tmnxL2tpTuMlpppEpMacAddress specifies the class 3 address to use in the MLPPP Endpoint Discriminator Option. While the value of tmnxL2tpTuMlpppEpClass is equal to 'macAddress', a value of all zeroes specifies that the system MAC address be used; otherwise, it means that no address is specified.
Status: current Access: read-create
OBJECT-TYPE    
  MacAddress  

tmnxL2tpTuStatusTableLastCh 1.3.6.1.4.1.6527.3.1.2.60.1.13
The value of the object tmnxL2tpTuStatusTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpTuStatusTable.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpTuStatusTable 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2
The tmnxL2tpTuStatusTable has an entry for each Layer Two Tunneling Protocol Tunnel.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpTuStatusEntry

tmnxL2tpTuStatusEntry 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1
Each conceptual row represents a Layer Two Tunneling Protocol Tunnel. Entries in this table are created and destroyed by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpTuStatusEntry  

tmnxL2tpTuStatusId 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.1
The value of the object tmnxL2tpTuStatusId indicates the local identifier of this Layer Two Tunneling Protocol Tunnel. In L2TP version 2, it contains the 16-bit tunnel ID in the high-order bits. In L2TP version 3, it is the 32-bit control connection ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpConnectionId  

tmnxL2tpTuStatusState 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.2
The value of tmnxL2tpTuStatusState indicates the operational state of this Layer Two Tunneling Protocol Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpTuOperState  

tmnxL2tpTuStatusTunnelId 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.3
The value of the object tmnxL2tpTuStatusTunnelId indicates the local identifier of this Layer Two Tunneling Protocol Tunnel, when L2TP version 2 is used. In L2TP version 3, it is equal to zero.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpTunnelId  

tmnxL2tpTuStatusPreference 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.4
The value of tmnxL2tpTuStatusPreference indicates the preference of this Layer Two Tunneling Protocol Tunnel. The value '0' corresponds to the highest preference.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpTunnelPreference  

tmnxL2tpTuStatusPeerAddrType 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.5
The value of tmnxL2tpTuStatusPeerAddrType indicates the address type of tmnxL2tpTuStatusPeerAddr.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

tmnxL2tpTuStatusPeerAddr 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.6
The value of tmnxL2tpTuStatusPeerAddr indicates the IP address of the peer.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress Size(0|4|16)  

tmnxL2tpTuStatusAddrType 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.7
The value of tmnxL2tpTuStatusAddrType indicates the address type of tmnxL2tpTuStatusAddr.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

tmnxL2tpTuStatusAddr 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.8
The value of tmnxL2tpTuStatusAddr indicates the local IP address of this Layer Two Tunneling Protocol Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress Size(0|4|16)  

tmnxL2tpTuStatusLocalName 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.9
The value of the object tmnxL2tpTuStatusLocalName indicates the host name used by this system during the authentication phase of tunnel establishment. This object is related to the RADIUS attribute Tunnel-Client-Auth-ID. It can be used to distinguish tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpHostNameOrEmpty  

tmnxL2tpTuStatusRemoteName 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.10
The value of the object tmnxL2tpTuStatusRemoteName indicates a string that is compared to the host name used by the tunnel peer during the authentication phase of tunnel establishment. This object is related to the RADIUS attribute Tunnel-Server-Auth-ID. It can be used to distinguish tunnels.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpHostNameOrEmpty  

tmnxL2tpTuStatusAssignmentId 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.11
The value of the object tmnxL2tpTuStatusAssignmentId indicates a string that distinguishes this Layer Two Tunneling Protocol Tunnel. This object is related to the RADIUS attribute Tunnel-Assignment-ID. If this tunnel corresponds to an entry in the tmnxL2tpTuCfgTable, the value of this object is equal to the value of the object tmnxL2tpTuCfgName.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpTunnelNameOrEmpty  

tmnxL2tpTuStatusHelloInterval 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.13
The value of tmnxL2tpTuStatusHelloInterval indicates the time interval between two consecutive tunnel Hello messages. A value of '-1' indicates that the keepalive function is disabled.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpTunnelHelloInterval  

tmnxL2tpTuStatusIdleTO 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.14
The value of tmnxL2tpTuStatusIdleTO indicates the period of time that this Layer Two Tunneling Protocol Tunnel will persist while it has no active sessions before being disconnected. A value of -1 indicates that the tunnel will not be disconnected when it has no more active sessions.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpTunnelIdleTO  

tmnxL2tpTuStatusDestructTO 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.15
The value of tmnxL2tpTuStatusIdleTO indicates the period of time that data of this Layer Two Tunneling Protocol Tunnel will persist after it is disconnected.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpTunnelDestructTO  

tmnxL2tpTuStatusMaxRetxEstab 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.16
The value of tmnxL2tpTuStatusMaxRetxEstab indicates the number of retries allowed for this Layer Two Tunneling Protocol Tunnel while it is established, before its control connection goes down.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpTunnelMaxRetx  

tmnxL2tpTuStatusMaxRetxNotEstab 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.17
The value of tmnxL2tpTuStatusMaxRetxNotEstab indicates the number of retries allowed for this Layer Two Tunneling Protocol Tunnel while it is unestablished, before its control connection goes down.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpTunnelMaxRetx  

tmnxL2tpTuStatusSessionLimit 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.18
The value of tmnxL2tpTuStatusSessionLimit indicates the maximum number of sessions allowed in this Layer Two Tunneling Protocol Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpTunnelSessionLimit  

tmnxL2tpTuStatusAvpHiding 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.19
The value of tmnxL2tpTuStatusAvpHiding indicates when the H bit in the header of each Attribute Value Pair (AVP) is set for the L2TP control messages related to this Layer Two Tunneling Protocol Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpAvpHidingMode  

tmnxL2tpTuStatusGroupName 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.20
The value of tmnxL2tpTuStatusGroupName indicates the name of the tunnel group where this Layer Two Tunneling Protocol Tunnel belongs to.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpTunnelGroupNameOrEmpty  

tmnxL2tpTuStatusRemoteTunnelId 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.21
The value of the object tmnxL2tpTuStatusRemoteTunnelId indicates the identifier of this Layer Two Tunneling Protocol Tunnel used by the tunnel peer, when L2TP version 2 is used. In L2TP version 3, it is equal to zero.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpTunnelId  

tmnxL2tpTuStatusRemoteConnId 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.22
The value of the object tmnxL2tpTuStatusRemoteConnId indicates the identifier of this Layer Two Tunneling Protocol Tunnel used by the tunnel peer.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpConnectionId  

tmnxL2tpTuStatusTransportType 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.23
The value of the object tmnxL2tpTuStatusTransportType indicates the transport type used for the messages of this Layer Two Tunneling Protocol Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpTransportType  

tmnxL2tpTuStatusUdpPort 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.24
The value of tmnxL2tpTuStatusAddr indicates the local UDP port of this Layer Two Tunneling Protocol Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  InetPortNumber  

tmnxL2tpTuStatusRemoteUdpPort 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.25
The value of the object tmnxL2tpTuStatusRemoteUdpPort indicates the UDP port of this Layer Two Tunneling Protocol Tunnel used by the tunnel peer.
Status: current Access: read-only
OBJECT-TYPE    
  InetPortNumber  

tmnxL2tpTuStatusStartTime 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.26
The value of the object tmnxL2tpTuStatusStartTime indicates the value of sysUpTime when this Layer Two Tunneling Protocol Tunnel entered either the state 'waitReply' or 'waitConn'.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpTuStatusEstabTime 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.27
The value of the object tmnxL2tpTuStatusEstabTime indicates the value of sysUpTime when this Layer Two Tunneling Protocol Tunnel entered the state 'established'. The value zero means that this tunnel has not been established yet.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpTuStatusIdleTime 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.28
The value of the object tmnxL2tpTuStatusIdleTime indicates the value of sysUpTime when this Layer Two Tunneling Protocol Tunnel entered the state 'idle'. The value zero means that this tunnel has not become idle yet.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpTuStatusClosedTime 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.29
The value of the object tmnxL2tpTuStatusClosedTime indicates the value of sysUpTime when this Layer Two Tunneling Protocol Tunnel entered one of the closed states. The value zero means that this tunnel has not been closed yet.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpTuStatusStopCcnResult 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.30
The value of tmnxL2tpTuStatusStopCcnResult indicates the result of a StopCCN (Stop-Control-Connection-Notification) message related to this Layer Two Tunneling Protocol Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpStopCcnResult  

tmnxL2tpTuStatusGeneralError 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.31
The value of tmnxL2tpTuStatusGeneralError indicates an general error related to this Layer Two Tunneling Protocol Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpGeneralError  

tmnxL2tpTuStatusErrorMessage 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.32
The value of the object tmnxL2tpTuStatusErrorMessage indicates describes an error related to this Layer Two Tunneling Protocol Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpErrorMessage  

tmnxL2tpTuStatusDoChallenge 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.33
The value of tmnxL2tpTuStatusDoChallenge indicates when challenge-response is used for the authentication of this Layer Two Tunneling Protocol Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpDoChallenge  

tmnxL2tpTuStatusRws 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.34
The value of tmnxL2tpTuStatusRws indicates the actual Receive Window Size of this Layer Two Tunneling Protocol Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxL2tpTuStatusTxDestAddrType 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.35
The value of tmnxL2tpTuStatusTxDestAddrType indicates the address type of tmnxL2tpTuStatusTxDestAddr.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

tmnxL2tpTuStatusTxDestAddr 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.36
The value of tmnxL2tpTuStatusTxDestAddr indicates the destination IP address used while transmitting L2TP control messages for this Layer Two Tunneling Protocol Tunnel. The destination address can be different from the value of the object tmnxL2tpTuStatusPeerAddr in case the value of the object tmnxL2tpPeerAddrChangePlcy is equal to 'accept'.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress Size(0|4|16)  

tmnxL2tpTuStatusRxSrcAddrType 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.37
The value of tmnxL2tpTuStatusRxSrcAddrType indicates the address type of tmnxL2tpTuStatusRxSrcAddr.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddressType  

tmnxL2tpTuStatusRxSrcAddr 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.38
The value of tmnxL2tpTuStatusRxSrcAddr indicates the source IP address found in L2TP control messages received for this Layer Two Tunneling Protocol Tunnel. The source address can be different from the value of the object tmnxL2tpTuStatusAddr in case the value of the object tmnxL2tpPeerAddrChangePlcy is equal to 'accept' or 'ignore'.
Status: current Access: read-only
OBJECT-TYPE    
  InetAddress Size(0|4|16)  

tmnxL2tpTuStatusAccountingPolicy 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.2.1.40
The value of tmnxL2tpTuStatusAccountingPolicy indicates the RADIUS accounting policy of this Layer Two Tunneling Protocol Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxL2tpTuStatsTable 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3
The tmnxL2tpTuStatsTable has an entry for each Layer Two Tunneling Protocol Tunnel.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpTuStatsEntry

tmnxL2tpTuStatsEntry 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1
Each conceptual row represents statistics information of a Layer Two Tunneling Protocol Tunnel. Entries in this table are created and destroyed by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpTuStatsEntry  

tmnxL2tpTuStatsLastCleared 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.1
The value of the object tmnxL2tpTuStatsLastCleared indicates the value of sysUpTime when the contents of this conceptual row were cleared for the last time. The value zero means that the contents of this conceptual row have not yet been cleared.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpTuStatsTotalSessions 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.2
The value of tmnxL2tpTuStatsTotalSessions indicates the number of session creation attempts in this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpTuStatsFailedSessions 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.3
The value of tmnxL2tpTuStatsFailedSessions indicates the number of sessions in this tunnel that failed to reach the established state since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpTuStatsActiveSessions 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.4
The value of tmnxL2tpTuStatsActiveSessions indicates the number of sessions currently established in this tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTuStatsSessions 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.5
The value of tmnxL2tpTuStatsSessions indicates the actual number of sessions in this tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTuStatsControlRxOctets 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.6
The value of tmnxL2tpTuStatsControlRxOctets indicates the number of control channel octets received in this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

tmnxL2tpTuStatsControlRxOctetsLw 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.7
The value of tmnxL2tpTuStatsControlRxOctetsLw indicates the lower 32-bits word of the value of tmnxL2tpTuStatsControlRxOctets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpTuStatsControlRxOctetsHw 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.8
The value of tmnxL2tpTuStatsControlRxOctetsHw indicates the higher 32-bits word of the value of tmnxL2tpTuStatsControlRxOctets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpTuStatsControlRxPkts 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.9
The value of tmnxL2tpTuStatsControlRxPkts indicates the number of control packets received by this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpTuStatsControlTxOctets 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.10
The value of tmnxL2tpTuStatsControlTxOctets indicates the number of control channel octets that were transmitted to the current tunnel endpoints in this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

tmnxL2tpTuStatsControlTxOctetsLw 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.11
The value of tmnxL2tpTuStatsControlTxOctetsLw indicates the lower 32-bits word of the value of tmnxL2tpTuStatsControlTxOctets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpTuStatsControlTxOctetsHw 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.12
The value of tmnxL2tpTuStatsControlTxOctetsHw indicates the higher 32-bits word of the value of tmnxL2tpTuStatsControlTxOctets.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpTuStatsControlTxPkts 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.13
The value of tmnxL2tpTuStatsControlTxOctets indicates the number of control packets that were transmitted to the current tunnel endpoints in this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpTuStatsErrorTxPkts 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.14
The value of tmnxL2tpTuStatsErrorTxPkts indicates the number of packet transmission errors on this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpTuStatsErrorRxPkts 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.15
The value of tmnxL2tpTuStatsErrorRxPkts indicates the number of errored packets that were received on this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpTuStatsFsmMsgAccepted 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.16
The value of tmnxL2tpTuStatsFsmMsgAccepted indicates the number of Finite State Machine (FSM) messages that were accepted on this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpTuStatsFsmMsgDuplicateRx 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.17
The value of tmnxL2tpTuStatsFsmMsgDuplicateRx indicates the number of Finite State Machine (FSM) duplicate messages that were received on this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpTuStatsFsmMsgOutOfWndwRx 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.18
The value of tmnxL2tpTuStatsFsmMsgOutOfWndwRx indicates the number of Finite State Machine (FSM) messages that were received out of the receive window on this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpTuStatsQLengthUnsentMax 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.19
The value of tmnxL2tpTuStatsQLengthUnsentMax indicates the the maximum length of the unsent message queue on this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTuStatsQLengthUnsentCur 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.20
The value of tmnxL2tpTuStatsErrorRxPkts indicates the the current length of the unsent message queue on this tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTuStatsQLengthAckMax 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.21
The value of tmnxL2tpTuStatsErrorRxPkts indicates the the maximum length of the acknowledged message queue on this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTuStatsQLengthAckCur 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.22
The value of tmnxL2tpTuStatsErrorRxPkts indicates the the current length of the acknowledged message queue on this tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTuStatsWindowSizeCur 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.3.1.23
The value of tmnxL2tpTuStatsErrorRxPkts indicates the the current size of the receive window on this tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpTuProtStatsTable 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.4
The tmnxL2tpTuProtStatsTable shows protocol statistics information of Layer Two Tunneling Protocol Tunnels.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpTuProtStatsEntry

tmnxL2tpTuProtStatsEntry 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.4.1
Each conceptual row represents protocol statistics of a specific type. Entries in this table are created and destroyed by the system. Rows are only created where the statistics value is nonzero; this allows faster walking through this table; hence, it is recommended to perform only get-next-request operations to retrieve information from this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpTuProtStatsEntry  

tmnxL2tpTuProtStatsType 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.4.1.1
The value of the object tmnxL2tpTuProtStatsType indicates the type of L2TP protocol statistics contained in this conceptual row.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpTuProtStatsType  

tmnxL2tpTuProtStatsInstance 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.4.1.2
The value of the object tmnxL2tpTuProtStatsType indicates the instance identifier of the statistics contained in this conceptual row. For example: if the value of the object tmnxL2tpTuProtStatsType is equal to 'outgoingMsgType', the value of tmnxL2tpTuProtStatsInstance is a message identifier, e.g. instance '2' refers to '(SCCRP) Start-Control-Connection-Reply', and the value of tmnxL2tpTuProtStatsVal indicates the number of SCCRP messages transmitted for this tunnel. Unknown protocol messages are counted with instance zero.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

tmnxL2tpTuProtStatsName 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.4.1.3
The value of the object tmnxL2tpTuProtStatsType indicates the human-readable identifier of the statistics contained in this conceptual row. In the same example, the value of tmnxL2tpTuProtStatsName is '(SCCRP) Start-Control-Connection-Reply'.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..64)  

tmnxL2tpTuProtStatsVal 1.3.6.1.4.1.6527.3.1.2.60.1.3.2.4.1.4
The value of the object tmnxL2tpTuProtStatsType indicates the value of the statistics contained in this conceptual row.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpTuStartTable 1.3.6.1.4.1.6527.3.1.2.60.1.3.3.1
The tmnxL2tpTuStartTable has an entry for each Layer Two Tunneling Protocol Tunnel.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpTuStartEntry

tmnxL2tpTuStartEntry 1.3.6.1.4.1.6527.3.1.2.60.1.3.3.1.1
Each conceptual row presents an operations interface to start a Layer Two Tunneling Protocol Tunnel control connection. Entries in this table are created and destroyed by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpTuStartEntry  

tmnxL2tpTuStart 1.3.6.1.4.1.6527.3.1.2.60.1.3.3.1.1.1
Setting this object to 'doAction (1)' triggers an attempt to start the control connection for this L2TP tunnel. Reading this object returns the value 'notApplicable'.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxActionType  

tmnxL2tpTuStopTable 1.3.6.1.4.1.6527.3.1.2.60.1.3.3.2
The tmnxL2tpTuStopTable has an entry for each active Layer Two Tunneling Protocol Tunnel.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpTuStopEntry

tmnxL2tpTuStopEntry 1.3.6.1.4.1.6527.3.1.2.60.1.3.3.2.1
Each conceptual row presents an operations interface to stop a Layer Two Tunneling Protocol Tunnel control connection. Entries in this table are created and destroyed by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpTuStopEntry  

tmnxL2tpTuStop 1.3.6.1.4.1.6527.3.1.2.60.1.3.3.2.1.1
Setting this object to 'doAction (1)' triggers an attempt to stop the control connection for this L2TP tunnel. Reading this object returns the value 'notApplicable'.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxActionType  

tmnxL2tpTuDrainTable 1.3.6.1.4.1.6527.3.1.2.60.1.3.3.3
The tmnxL2tpTuDrainTable has an entry for each active Layer Two Tunneling Protocol Tunnel.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpTuDrainEntry

tmnxL2tpTuDrainEntry 1.3.6.1.4.1.6527.3.1.2.60.1.3.3.3.1
Each conceptual row presents an operations interface to drain a Layer Two Tunneling Protocol Tunnel. After a successful drain operation, the value of the object tmnxL2tpTuStatusState of this tunnel is equal to 'draining'; this tunnel does not accept or establish new connections, while existing connections are timing out. Entries in this table are created and destroyed by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpTuDrainEntry  

tmnxL2tpTuDrain 1.3.6.1.4.1.6527.3.1.2.60.1.3.3.3.1.1
Setting this object to 'drain (0)' triggers an attempt to drain this L2TP tunnel. Setting it to 'stopDrain (1)' stops the draining. Reading this object returns the value 'notApplicable'.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxL2tpActionTypeDrain  

tmnxL2tpPeerStatObjs 1.3.6.1.4.1.6527.3.1.2.60.1.4.1
OBJECT IDENTIFIER    

tmnxL2tpPeerOpObjs 1.3.6.1.4.1.6527.3.1.2.60.1.4.2
OBJECT IDENTIFIER    

tmnxL2tpPeerStatTable 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1
The tmnxL2tpPeerStatTable contains status and statistics information about L2TP peers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpPeerStatEntry

tmnxL2tpPeerStatEntry 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1
Each row entry represents status and statistics information about a particular L2TP peer. Rows are created or removed automatically by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpPeerStatEntry  

tmnxL2tpPeerStatRole 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.1
The value of tmnxL2tpPeerStatRole indicates the role of this system in relation to the peer.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER roleLAC(1), roleLNS(2)  

tmnxL2tpPeerStatActiveTunnels 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.2
The value of tmnxL2tpPeerStatActiveTunnels indicates the number of tunnels associated with this peer that are currently established.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpPeerStatTunnels 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.3
The value of tmnxL2tpPeerStatTunnels indicates the actual number of tunnels associated with this peer.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpPeerStatActiveSessions 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.4
The value of tmnxL2tpPeerStatActiveSessions indicates the number of sessions associated with this peer that are currently established.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpPeerStatSessions 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.5
The value of tmnxL2tpPeerStatSessions indicates the actual number of sessions associated with this peer.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpPeerStatDraining 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.6
The value of tmnxL2tpPeerStatDraining indicates if this peer is being drained.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

tmnxL2tpPeerStatUnreachable 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.7
The value of tmnxL2tpPeerStatUnreachable indicates if this peer is deemed unreachable.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

tmnxL2tpPeerStatUnreachableTime 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.8
The value of the object tmnxL2tpPeerStatUnreachableTime indicates the value of sysUpTime when the this peer was deemed unreachable for the last time. The value zero means that this peer has not been deemed unreachable yet.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpPeerStatControlRxOct 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.9
The value of tmnxL2tpPeerStatControlRxOct indicates the number of control channel octets received in this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

tmnxL2tpPeerStatControlRxOctLw 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.10
The value of tmnxL2tpPeerStatControlRxOctLw indicates the lower 32-bits word of the value of tmnxL2tpPeerStatControlRxOct.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpPeerStatControlRxOctHw 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.11
The value of tmnxL2tpPeerStatControlRxOctHw indicates the higher 32-bits word of the value of tmnxL2tpPeerStatControlRxOct.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpPeerStatControlRxPkts 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.12
The value of tmnxL2tpPeerStatControlRxPkts indicates the number of control packets received by this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpPeerStatControlTxOct 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.13
The value of tmnxL2tpPeerStatControlTxOct indicates the number of control channel octets that were transmitted to the current tunnel endpoints in this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter64  

tmnxL2tpPeerStatControlTxOctLw 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.14
The value of tmnxL2tpPeerStatControlTxOctLw indicates the lower 32-bits word of the value of tmnxL2tpPeerStatControlTxOct.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpPeerStatControlTxOctHw 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.15
The value of tmnxL2tpPeerStatControlTxOctHw indicates the higher 32-bits word of the value of tmnxL2tpPeerStatControlTxOct.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpPeerStatControlTxPkts 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.16
The value of tmnxL2tpPeerStatControlTxOct indicates the number of control packets that were transmitted to the current tunnel endpoints in this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpPeerStatErrorTxPkts 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.17
The value of tmnxL2tpPeerStatErrorTxPkts indicates the number of packet transmission errors on this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpPeerStatErrorRxPkts 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.18
The value of tmnxL2tpPeerStatErrorRxPkts indicates the number of errored packets that were received on this tunnel since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpPeerStatMsgAccepted 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.19
The value of tmnxL2tpPeerStatMsgAccepted indicates the number of Finite State Machine (FSM) messages that were accepted from this peer since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpPeerStatMsgDuplicateRx 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.20
The value of tmnxL2tpPeerStatMsgDuplicateRx indicates the number of Finite State Machine (FSM) duplicate messages that were received from this peer since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpPeerStatMsgOutOfWndwRx 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.21
The value of tmnxL2tpPeerStatMsgOutOfWndwRx indicates the number of Finite State Machine (FSM) messages that were received out of the receive window from this peer since the last re-initialization of the local network management subsystem, or the last time the tunnel statistics were cleared.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpPeerStatRolesCapability 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.22
The value of tmnxL2tpPeerStatRolesCapability indicates the roles that this system could perform in relation to the peer.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpRoles  

tmnxL2tpPeerStatRoles 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.23
The value of tmnxL2tpPeerStatRole indicates the actual roles of this system in relation to the peer.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpRoles  

tmnxL2tpPeerStatLastCleared 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.1.1.99
The value of the object tmnxL2tpPeerStatLastCleared indicates the value of sysUpTime when the contents of this conceptual row were cleared for the last time. The value zero means that the contents of this conceptual row have not yet been cleared.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpPeerTuTable 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.2
The tmnxL2tpPeerTuTable contains the set of active tunnels for each L2TP peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpPeerTuEntry

tmnxL2tpPeerTuEntry 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.2.1
Each row entry contains a tunnel identifier of an L2TP peer. Rows are created or removed automatically by the system. Note that all L2TP peers appear in this table with remote UDP port equal to 1701, regardless of the actual port in use.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpPeerTuEntry  

tmnxL2tpPeerTuId 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.2.1.1
The value of the object tmnxL2tpPeerTuId indicates the local identifier of a Layer Two Tunneling Protocol Tunnel.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpConnectionId  

tmnxL2tpPeerProtStatsTable 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3
The tmnxL2tpPeerProtStatsTable contains protocol statistics information about L2TP peers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpPeerProtStatsEntry

tmnxL2tpPeerProtStatsEntry 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3.1
Each conceptual row represents protocol statistics of a specific type for a specific L2TP peer. Entries in this table are created and destroyed by the system. Rows are only created where the statistics value is nonzero; this allows faster walking through this table; hence, it is recommended to perform only get-next-request operations to retrieve information from this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpPeerProtStatsEntry  

tmnxL2tpPeerProtStatsTransport 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3.1.1
The value of the object tmnxL2tpTuStatusTransportType indicates the transport type used for the messages to this L2TP peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpTransportType  

tmnxL2tpPeerProtStatsAddrType 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3.1.2
The value of tmnxL2tpPeerProtStatsAddrType indicates the address type of tmnxL2tpPeerProtStatsAddr.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

tmnxL2tpPeerProtStatsAddr 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3.1.3
The value of tmnxL2tpPeerProtStatsAddr indicates the IP address of the peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetAddress Size(0|4|16)  

tmnxL2tpPeerProtStatsRemUdpPort 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3.1.4
The value of the object tmnxL2tpPeerProtStatsRemUdpPort indicates the UDP port used by the tunnel peer.
Status: current Access: not-accessible
OBJECT-TYPE    
  InetPortNumber  

tmnxL2tpPeerProtStatsType 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3.1.5
The value of the object tmnxL2tpPeerProtStatsType indicates the type of L2TP protocol statistics contained in this conceptual row.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpTuProtStatsType  

tmnxL2tpPeerProtStatsInstance 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3.1.6
The value of the object tmnxL2tpPeerProtStatsInstance indicates the instance identifier of the statistics contained in this conceptual row. For example: if the value of the object tmnxL2tpPeerProtStatsType is equal to 'outgoingMsgType', the value of tmnxL2tpPeerProtStatsInstance is a message identifier, e.g. instance '2' refers to '(SCCRP) Start-Control-Connection-Reply', and the value of tmnxL2tpPeerProtStatsVal indicates the number of SCCRP messages transmitted for this tunnel. Unknown protocol messages are counted with instance zero.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

tmnxL2tpPeerProtStatsName 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3.1.7
The value of the object tmnxL2tpPeerProtStatsName indicates the human-readable identifier of the statistics contained in this conceptual row. In the same example, the value of tmnxL2tpPeerProtStatsName is '(SCCRP) Start-Control-Connection-Reply'.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..64)  

tmnxL2tpPeerProtStatsVal 1.3.6.1.4.1.6527.3.1.2.60.1.4.1.3.1.8
The value of the object tmnxL2tpPeerProtStatsVal indicates the value of the statistics contained in this conceptual row.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpPeerDrainTable 1.3.6.1.4.1.6527.3.1.2.60.1.4.2.1
The tmnxL2tpPeerDrainTable has an entry for each L2TP peer. Note that all L2TP peers appear in this table with remote UDP port equal to 1701, regardless of the actual port in use.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpPeerDrainEntry

tmnxL2tpPeerDrainEntry 1.3.6.1.4.1.6527.3.1.2.60.1.4.2.1.1
Each row entry presents an operations interface to drain all tunnels between this system and a particular L2TP peer. Rows are created or removed automatically by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpPeerDrainEntry  

tmnxL2tpPeerDrain 1.3.6.1.4.1.6527.3.1.2.60.1.4.2.1.1.1
Setting this object to 'drain (0)' triggers an attempt to drain all tunnels between this system and a particular L2TP peer. Setting it to 'stopDrain (1)' stops the draining. Reading this object returns the value 'notApplicable'.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxL2tpActionTypeDrain  

tmnxL2tpSeStatObjs 1.3.6.1.4.1.6527.3.1.2.60.1.5.1
OBJECT IDENTIFIER    

tmnxL2tpSeOpObjs 1.3.6.1.4.1.6527.3.1.2.60.1.5.2
OBJECT IDENTIFIER    

tmnxL2tpSeStatusTableLastCh 1.3.6.1.4.1.6527.3.1.2.60.1.14
The value of the object tmnxL2tpSeStatusTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpSeStatusTable.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpSeStatusTable 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1
The tmnxL2tpSeStatusTable has an entry for each Layer Two Tunneling Protocol Session.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpSeStatusEntry

tmnxL2tpSeStatusEntry 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1
Each conceptual row represents a Layer Two Tunneling Protocol Session. Entries in this table are created and destroyed by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpSeStatusEntry  

tmnxL2tpSeStatusId 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.1
The value of the object tmnxL2tpSeStatusId indicates the local identifier of this Layer Two Tunneling Protocol Session. In L2TP version 2, it contains the 16-bit session ID in the lower order bits and the 16-bit tunnel ID in the higher order bits. In L2TP version 3, it is the 32-bit session ID.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpConnectionId  

tmnxL2tpSeStatusState 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.2
The value of tmnxL2tpSeStatusState indicates the operational state of this Layer Two Tunneling Protocol Session.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpSeOperState  

tmnxL2tpSeStatusTunnelId 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.3
The value of the object tmnxL2tpSeStatusTunnelId indicates the identifier of the L2TP tunnel associated with this Layer Two Tunneling Protocol Session, when L2TP version 2 is used. In L2TP version 3, it is equal to zero.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpTunnelId  

tmnxL2tpSeStatusTunnelConnId 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.4
The value of the object tmnxL2tpSeStatusTunnelConnId indicates the identifier of the L2TP tunnel associated with this Layer Two Tunneling Protocol Session.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpConnectionId  

tmnxL2tpSeStatusSessionId 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.5
The value of the object tmnxL2tpSeStatusSessionId indicates the identifier of this Layer Two Tunneling Protocol Session, when L2TP version 2 is used. In L2TP version 3, it is equal to zero.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpSessionId  

tmnxL2tpSeStatusRemoteTunnelId 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.6
The value of the object tmnxL2tpSeStatusRemoteTunnelId indicates the identifier used by the tunnel peer of the L2TP tunnel associated with this Layer Two Tunneling Protocol Session , when L2TP version 2 is used. In L2TP version 3, it is equal to zero.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpTunnelId  

tmnxL2tpSeStatusRemoteSessionId 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.7
The value of the object tmnxL2tpSeStatusRemoteSessionId indicates the identifier of this Layer Two Tunneling Protocol Session used by the tunnel peer, when L2TP version 2 is used. In L2TP version 3, it is equal to zero.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpSessionId  

tmnxL2tpSeStatusRemoteConnId 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.8
The value of the object tmnxL2tpSeStatusRemoteConnId indicates the identifier of this Layer Two Tunneling Protocol Session used by the tunnel peer.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpConnectionId  

tmnxL2tpSeStatusStartTime 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.9
The value of the object tmnxL2tpSeStatusStartTime indicates the value of sysUpTime when this Layer Two Tunneling Protocol Session entered either the state 'idle', 'waitTunnel', 'waitReply' or 'waitAcceptance'.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpSeStatusEstabTime 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.10
The value of the object tmnxL2tpSeStatusEstabTime indicates the value of sysUpTime when this Layer Two Tunneling Protocol Session entered the state 'established'. The value zero means that this session has not been established yet.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpSeStatusClosedTime 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.11
The value of the object tmnxL2tpSeStatusClosedTime indicates the value of sysUpTime when this Layer Two Tunneling Protocol Session entered one of the closed states. The value zero means that this session has not been closed yet.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpSeStatusCdnResult 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.12
The value of tmnxL2tpSeStatusCdnResult indicates the result of a CDN (Call-Disconnect-Notify) message related to this Layer Two Tunneling Protocol Session.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpCdnResult  

tmnxL2tpSeStatusGeneralError 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.13
The value of tmnxL2tpSeStatusGeneralError indicates an general error related to this Layer Two Tunneling Protocol Session.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpGeneralError  

tmnxL2tpSeStatusErrorMessage 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.14
The value of the object tmnxL2tpSeStatusErrorMessage describes an error related to this Layer Two Tunneling Protocol Session.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpErrorMessage  

tmnxL2tpSeStatusMlpppBundleIndex 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.1.1.20
The value of the object tmnxL2tpSeStatusMlpppBundleIndex indicates the identifier of the MLPPP Bundle related to this Layer Two Tunneling Protocol Session. If an MLPPP bundle is associated with this session, the value of tmnxL2tpSeStatusMlpppBundleIndex is equal to the value of tmnxL2tpLacMlpppBundleIndex of the corresponding row in the tmnxL2tpLacMlpppBundleTable, in the same virtual router instance. If no MLPPP bundle is associated with this session, the value of this object is equal to zero.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxL2tpLnsSePppTableLastCh 1.3.6.1.4.1.6527.3.1.2.60.1.20
The value of the object tmnxL2tpLnsSePppTableLastCh indicates the value of sysUpTime at the time of the last update of an entry in the tmnxL2tpLnsSePppTable.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpLnsSePppTable 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2
The tmnxL2tpLnsSePppTable has an entry for each Layer Two Tunneling Protocol Session for which this system acts as LNS.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpLnsSePppEntry

tmnxL2tpLnsSePppEntry 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1
Each conceptual row represents a Layer Two Tunneling Protocol Session. Entries in this table are created and destroyed by the system. In release 9.0 and higher, this information is in the SUBSCRIBER-MGMT-MIB::tmnxSubPppTable. The corresponding row in that table can be directly retrieved using the value of the object tmnxL2tpLnsSePppSubPppIndex.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpLnsSePppEntry  

tmnxL2tpLnsSePppUpTime 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.3
The value of tmnxL2tpLnsSePppUpTime indicates how long (in hundredths of a second) that the session already exists in this table.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TimeTicks  

tmnxL2tpLnsSePppLcpState 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.4
The value of tmnxL2tpLnsSePppLcpState indicates the current state of the PPP Link Control Protocol of the session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxPppCpState  

tmnxL2tpLnsSePppIpcpState 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.5
The value of tmnxL2tpLnsSePppIpcpState indicates the current state of the PPP IP Control Protocol of the session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxPppCpState  

tmnxL2tpLnsSePppPppMtu 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.6
The value of tmnxL2tpLnsSePppPppMtu indicates the PPP MTU of the session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxL2tpLnsSePppPppAuthProtocol 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.7
The value of tmnxL2tpLnsSePppPppAuthProtocol indicates the PPP protocol used to authenticate the session. The value 'none' indicates that no PPP authentication was done. The value 'pap' indicates that authentication was done via the Password Authentication Protocol. The value 'chap' indicates that authentication was done via the Challenge-Handshake Authentication Protocol.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER none(1), pap(2), chap(3)  

tmnxL2tpLnsSePppPppUserName 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.8
The value of tmnxL2tpLnsSePppPppUserName indicates the user name learned during the PPP authentication phase.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxPppoeUserNameOrEmpty  

tmnxL2tpLnsSePppSubIdent 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.9
The value of tmnxL2tpLnsSePppSubIdent indicates the subscriber applicable for this session. The value of tmnxL2tpLnsSePppOriginSubIdent indicates from what source this subscriber identification was received.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxSubIdentStringOrEmpty  

tmnxL2tpLnsSePppOriginSubIdent 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.10
The value of tmnxL2tpLnsSePppOriginSubIdent indicates which source provided the subscriber.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxPppoeSessionInfoOrigin  

tmnxL2tpLnsSePppSubProfString 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.11
The value of tmnxL2tpLnsSePppSubProfString indicates the subscriber profile string applicable for this session. The value of tmnxL2tpLnsSePppOriginStrings indicates from what source this string was received.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxSubProfileStringOrEmpty  

tmnxL2tpLnsSePppSlaProfString 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.12
The value of tmnxL2tpLnsSePppSlaProfString indicates the SLA profile string applicable for this session. The value of tmnxL2tpLnsSePppOriginStrings indicates from what source this string was received.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxSlaProfileStringOrEmpty  

tmnxL2tpLnsSePppAncpString 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.13
The value of tmnxL2tpLnsSePppAncpString indicates the ANCP string applicable for this session. The value of tmnxL2tpLnsSePppOriginStrings indicates from what source this string was received.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxAncpStringOrZero  

tmnxL2tpLnsSePppInterDestId 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.14
The value of tmnxL2tpLnsSePppInterDestId indicates the intermediate destination identifier applicable for this session. The value of tmnxL2tpLnsSePppOriginStrings indicates from what source this string was received.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxSubMgtIntDestIdOrEmpty  

tmnxL2tpLnsSePppAppProfString 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.15
The value of tmnxL2tpLnsSePppAppProfString indicates the application profile string applicable for this session. The value of tmnxL2tpLnsSePppOriginStrings indicates from what source this string was received.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxAppProfileStringOrEmpty  

tmnxL2tpLnsSePppOriginStrings 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.16
The value of tmnxL2tpLnsSePppOriginStrings indicates which source provided the subscriber identification strings (subscriber profile string, SLA profile string, ANCP string, intermediate destination identifier and application profile string).
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxPppoeSessionInfoOrigin  

tmnxL2tpLnsSePppSessionTimeout 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.17
The value of tmnxL2tpLnsSePppSessionTimeout indicates the session timeout received from the Radius server (if applicable).
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32 0..65535  

tmnxL2tpLnsSePppIpAddrType 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.18
The value of tmnxL2tpLnsSePppIpAddrType indicates the address type of tmnxL2tpLnsSePppIpAddr.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InetAddressType  

tmnxL2tpLnsSePppIpAddr 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.19
The value of tmnxL2tpLnsSePppIpAddr indicates the IP address of the session. The value of tmnxL2tpLnsSePppOriginIpcpInfo indicates from what source this IP address was received.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InetAddress Size(0|4)  

tmnxL2tpLnsSePppPrimaryDnsType 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.20
The value of tmnxL2tpLnsSePppPrimaryDnsType indicates the address type of tmnxL2tpLnsSePppPrimaryDns.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InetAddressType  

tmnxL2tpLnsSePppPrimaryDns 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.21
The value of tmnxL2tpLnsSePppPrimaryDns indicates the primary DNS server. The value of this object is ''H when not applicable. The value of tmnxL2tpLnsSePppOriginIpcpInfo indicates from what source this IP address was received.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InetAddress Size(0|4)  

tmnxL2tpLnsSePppSecondaryDnsType 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.22
The value of tmnxL2tpLnsSePppSecondaryDnsType indicates the address type of tmnxL2tpLnsSePppSecondaryDns.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InetAddressType  

tmnxL2tpLnsSePppSecondaryDns 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.23
The value of tmnxL2tpLnsSePppSecondaryDns indicates the secondary DNS server. The value of this object is ''H when not applicable. The value of tmnxL2tpLnsSePppOriginIpcpInfo indicates from what source this IP address was received.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InetAddress Size(0|4)  

tmnxL2tpLnsSePppPrimaryNbnsType 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.24
The value of tmnxL2tpLnsSePppPrimaryNbnsType indicates the address type of tmnxL2tpLnsSePppPrimaryNbns.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InetAddressType  

tmnxL2tpLnsSePppPrimaryNbns 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.25
The value of tmnxL2tpLnsSePppPrimaryNbns indicates the primary NBNS server. The value of this object is ''H when not applicable. The value of tmnxL2tpLnsSePppOriginIpcpInfo indicates from what source this IP address was received.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InetAddress Size(0|4)  

tmnxL2tpLnsSePppSecondNbnsType 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.26
The value of tmnxL2tpLnsSePppSecondNbnsType indicates the address type of tmnxL2tpLnsSePppSecondNbns.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InetAddressType  

tmnxL2tpLnsSePppSecondNbns 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.27
The value of tmnxL2tpLnsSePppSecondNbns indicates the secondary NBNS server. The value of this object is ''H when not applicable. The value of tmnxL2tpLnsSePppOriginIpcpInfo indicates from what source this IP address was received.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InetAddress Size(0|4)  

tmnxL2tpLnsSePppOriginIpcpInfo 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.28
The value of tmnxL2tpLnsSePppOriginIpcpInfo indicates which source provided the IPCP information (IP, DNS and NBNS addresses).
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxPppoeSessionInfoOrigin  

tmnxL2tpLnsSePppCircuitId 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.29
The value of tmnxL2tpLnsSePppCircuitId indicates the value of the circuit-id sub-option.
Status: obsolete Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..256)  

tmnxL2tpLnsSePppRemoteId 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.30
The value of tmnxL2tpLnsSePppRemoteId indicates the value of the remote-id sub-option.
Status: obsolete Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..256)  

tmnxL2tpLnsSePppAddressPool 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.31
The value of tmnxL2tpLnsSePppAddressPool indicates the IP address pool which is used to search for an IP address for this session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

tmnxL2tpLnsSePppType 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.32
The value of tmnxL2tpLnsSePppType indicates the type of this session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxPppoeSessionType  

tmnxL2tpLnsSePppSvcId 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.33
The value of tmnxL2tpLnsSePppSvcId indicates the service ID of the IES/VPRN service to which this session belongs.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxServId  

tmnxL2tpLnsSePppGrpIf 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.34
The value of tmnxL2tpLnsSePppGrpIf indicates the interface index of the group-interface to which this session belongs.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InterfaceIndexOrZero  

tmnxL2tpLnsSePppL2tpVrtrId 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.35
The value of tmnxL2tpLnsSePppL2tpVrtrId indicates the virtual router ID of the L2TP session associated with this session. If there is no L2TP session associated with this session, the value of this object is equal to zero.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxVRtrIDOrZero  

tmnxL2tpLnsSePppL2tpConnectionId 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.36
The value of tmnxL2tpLnsSePppL2tpVrtrId indicates the connection ID of the L2TP session associated with this session. The values of tmnxL2tpLnsSePppL2tpVrtrId and tmnxL2tpLnsSePppL2tpConnectionId are the index in the table TIMETRA-L2TP-MIB::tmnxL2tpSeStatusTable of the L2TP session associated with this session. If there is no L2TP session associated with this session, the value of this object is equal to zero.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxL2tpLnsSePppCategoryMapName 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.37
The value of tmnxL2tpLnsSePppCategoryMapName indicates the category map name applicable for this session. The value of tmnxL2tpLnsSePppOriginStrings indicates from what source this string was received.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxL2tpLnsSePppRadiusClassAttr 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.38
The value of tmnxL2tpLnsSePppRadiusClassAttr indicates the Class attribute returned by the RADIUS server in an Access-Accept message. If no RADIUS authentication is performed for this session, or RADIUS did not return this attribute, the value of this object is empty.
Status: obsolete Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..64)  

tmnxL2tpLnsSePppRadiusUserName 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.39
The value of tmnxL2tpLnsSePppRadiusUserName indicates the User-Name attribute returned by the RADIUS server in an Access-Accept message. If RADIUS did not return this attribute, the value of this object is equal to the User-Name attribute sent in the original Access-Request message. If no RADIUS authentication is performed for this session, the value of this object is empty.
Status: obsolete Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..128)  

tmnxL2tpLnsSePppIpv6cpState 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.40
The value of tmnxL2tpLnsSePppIpv6cpState indicates the current state of the PPP IPv6 Control Protocol of the PPPoE session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxPppCpState  

tmnxL2tpLnsSePppInterfaceId 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.41
The value of tmnxL2tpLnsSePppInterfaceId indicates the value of the remote-id sub-option inserted by the PPPoE intermediate agent.
Status: obsolete Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

tmnxL2tpLnsSePppOriginIpv6cpInfo 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.42
The value of tmnxL2tpLnsSePppOriginIpv6cpInfo indicates which source provided the IPCP information (IP, DNS and NBNS addresses).
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxPppoeSessionInfoOrigin  

tmnxL2tpLnsSePppIpv6DnsType 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.43
The value of tmnxL2tpLnsSePppIpv6DnsType indicates the address type of tmnxL2tpLnsSePppIpv6Dns1/2.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InetAddressType  

tmnxL2tpLnsSePppIpv6Dns1 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.44
The value of tmnxL2tpLnsSePppIpv6Dns1 indicates the primary DNS server. The value of this object is ''H when not applicable. The value of tmnxL2tpLnsSePppOriginIpv6cpInfo indicates from what source this IP address was received.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InetAddress Size(0|16)  

tmnxL2tpLnsSePppIpv6Dns2 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.45
The value of tmnxL2tpLnsSePppIpv6Dns2 indicates the secondary DNS server. The value of this object is ''H when not applicable. The value of tmnxL2tpLnsSePppOriginIpv6cpInfo indicates from what source this IP address was received.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InetAddress Size(0|16)  

tmnxL2tpLnsSePppIpv6DelPfxType 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.46
The value of tmnxL2tpLnsSePppIpv6DelPfxType indicates the address type of tmnxL2tpLnsSePppIpv6DelPfx.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InetAddressType  

tmnxL2tpLnsSePppIpv6DelPfxLen 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.47
The value of tmnxL2tpLnsSePppIpv6DelPfxLen indicates the length of tmnxL2tpLnsSePppIpv6DelPfx.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InetAddressPrefixLength 0..128  

tmnxL2tpLnsSePppIpv6DelPfx 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.48
The value of tmnxL2tpLnsSePppIpv6DelPfx indicates the IPv6 prefix used for DHCPv6 prefix delegation.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InetAddress Size(0|16)  

tmnxL2tpLnsSePppIpv6PrefixType 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.49
The value of tmnxL2tpLnsSePppIpv6PrefixType indicates the address type of tmnxL2tpLnsSePppIpv6Prefix.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InetAddressType  

tmnxL2tpLnsSePppIpv6PrefixLen 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.50
The value of tmnxL2tpLnsSePppIpv6PrefixLen indicates the length of tmnxL2tpLnsSePppIpv6Prefix.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InetAddressPrefixLength 0..128  

tmnxL2tpLnsSePppIpv6Prefix 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.51
The value of tmnxL2tpLnsSePppIpv6Prefix indicates the IPv6 prefix used for stateless address autoconfiguration.
Status: obsolete Access: read-only
OBJECT-TYPE    
  InetAddress Size(0|16)  

tmnxL2tpLnsSePppSubPppIndex 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.2.1.52
The value of tmnxL2tpLnsSePppSubPppIndex indicates the local identifier of the subscriber PPP session. It is the index of the corresponding conceptual row in the TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppTable.
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32  

tmnxL2tpLnsSePppStatTable 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3
The tmnxL2tpLnsSePppStatTable has an entry for each Layer Two Tunneling Protocol Session for which this system acts as LNS. This table is replaced with TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppStatTable.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpLnsSePppStatEntry

tmnxL2tpLnsSePppStatEntry 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1
Each conceptual row represents a Layer Two Tunneling Protocol Session. Entries in this table are created and destroyed by the system.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpLnsSePppStatEntry  

tmnxL2tpLnsSePppStatRxUnkwnProto 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.2
The value of tmnxL2tpLnsSePppStatRxUnkwnProto indicates the number of packets with unknown PPP protocol received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxLcpConfRq 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.3
The value of tmnxL2tpLnsSePppStatRxLcpConfRq indicates the number of LCP configure requests received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxLcpConfAk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.4
The value of tmnxL2tpLnsSePppStatRxLcpConfAk indicates the number of LCP configure acknowledgements received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxLcpConfNk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.5
The value of tmnxL2tpLnsSePppStatRxLcpConfNk indicates the number of negative LCP configure acknowledgements received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxLcpConfRj 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.6
The value of tmnxL2tpLnsSePppStatRxLcpConfRj indicates the number of LCP configure rejects received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxLcpTermRq 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.7
The value of tmnxL2tpLnsSePppStatRxLcpTermRq indicates the number of LCP terminate requests received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxLcpTermAk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.8
The value of tmnxL2tpLnsSePppStatRxLcpTermAk indicates the number of LCP terminate acknowledgements received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxLcpCodeRj 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.9
The value of tmnxL2tpLnsSePppStatRxLcpCodeRj indicates the number of LCP code rejects received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxLcpEchoRq 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.10
The value of tmnxL2tpLnsSePppStatRxLcpEchoRq indicates the number of LCP echo requests received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxLcpEchoRep 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.11
The value of tmnxL2tpLnsSePppStatRxLcpEchoRep indicates the number of LCP echo replies received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxLcpProtRj 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.12
The value of tmnxL2tpLnsSePppStatRxLcpProtRj indicates the number of LCP protocol rejects received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxLcpDiscRq 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.13
The value of tmnxL2tpLnsSePppStatRxLcpDiscRq indicates the number of LCP discard requests received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxLcpConfRq 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.14
The value of tmnxL2tpLnsSePppStatTxLcpConfRq indicates the number of LCP configure requests transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxLcpConfAk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.15
The value of tmnxL2tpLnsSePppStatTxLcpConfAk indicates the number of LCP configure acknowledgements transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxLcpConfNk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.16
The value of tmnxL2tpLnsSePppStatTxLcpConfNk indicates the number of negative LCP configure acknowledgements transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxLcpConfRj 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.17
The value of tmnxL2tpLnsSePppStatTxLcpConfRj indicates the number of LCP configure rejects transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxLcpTermRq 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.18
The value of tmnxL2tpLnsSePppStatTxLcpTermRq indicates the number of LCP terminate requests transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxLcpTermAk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.19
The value of tmnxL2tpLnsSePppStatTxLcpTermAk indicates the number of LCP terminate acknowledgements transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxLcpCodeRj 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.20
The value of tmnxL2tpLnsSePppStatTxLcpCodeRj indicates the number of LCP code rejects transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxLcpEchoRq 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.21
The value of tmnxL2tpLnsSePppStatTxLcpEchoRq indicates the number of LCP echo requests transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxLcpEchoRep 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.22
The value of tmnxL2tpLnsSePppStatTxLcpEchoRep indicates the number of LCP echo replies transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxLcpProtRj 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.23
The value of tmnxL2tpLnsSePppStatTxLcpProtRj indicates the number of LCP protocol rejects transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxLcpDiscRq 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.24
The value of tmnxL2tpLnsSePppStatTxLcpDiscRq indicates the number of LCP discard requests transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxPapAuthRq 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.25
The value of tmnxL2tpLnsSePppStatRxPapAuthRq indicates the number of PAP authentication requests received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxPapAuthAk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.26
The value of tmnxL2tpLnsSePppStatTxPapAuthAk indicates the number of PAP authentication acknowledgements transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxPapAuthNk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.27
The value of tmnxL2tpLnsSePppStatTxPapAuthNk indicates the number of negative PAP authentication acknowledgements transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxChapResp 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.28
The value of tmnxL2tpLnsSePppStatRxChapResp indicates the number of CHAP authentication responses received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxChapChall 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.29
The value of tmnxL2tpLnsSePppStatTxChapChall indicates the number of CHAP authentication challenges transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxChapSucc 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.30
The value of tmnxL2tpLnsSePppStatTxChapSucc indicates the number of CHAP authentication acknowledgements transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxChapFail 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.31
The value of tmnxL2tpLnsSePppStatTxChapFail indicates the number of negative CHAP authentication acknowledgements transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxIpcpConfRq 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.32
The value of tmnxL2tpLnsSePppStatRxIpcpConfRq indicates the number of IPCP configure requests received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxIpcpConfAk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.33
The value of tmnxL2tpLnsSePppStatRxIpcpConfAk indicates the number of IPCP configure acknowledgements received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxIpcpConfNk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.34
The value of tmnxL2tpLnsSePppStatRxIpcpConfNk indicates the number of negative IPCP configure acknowledgements received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxIpcpConfRj 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.35
The value of tmnxL2tpLnsSePppStatRxIpcpConfRj indicates the number of IPCP configure rejects received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxIpcpTermRq 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.36
The value of tmnxL2tpLnsSePppStatRxIpcpTermRq indicates the number of IPCP terminate requests received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxIpcpTermAk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.37
The value of tmnxL2tpLnsSePppStatRxIpcpTermAk indicates the number of IPCP terminate acknowledgements received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxIpcpCodeRj 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.38
The value of tmnxL2tpLnsSePppStatRxIpcpCodeRj indicates the number of IPCP code rejects received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxIpcpConfRq 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.39
The value of tmnxL2tpLnsSePppStatTxIpcpConfRq indicates the number of IPCP configure requests transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxIpcpConfAk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.40
The value of tmnxL2tpLnsSePppStatTxIpcpConfAk indicates the number of IPCP configure acknowledgements transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxIpcpConfNk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.41
The value of tmnxL2tpLnsSePppStatTxIpcpConfNk indicates the number of negative IPCP configure acknowledgements transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxIpcpConfRj 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.42
The value of tmnxL2tpLnsSePppStatTxIpcpConfRj indicates the number of IPCP configure rejects transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxIpcpTermRq 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.43
The value of tmnxL2tpLnsSePppStatTxIpcpTermRq indicates the number of IPCP terminate requests transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxIpcpTermAk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.44
The value of tmnxL2tpLnsSePppStatTxIpcpTermAk indicates the number of IPCP terminate acknowledgements transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxIpcpCodeRj 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.45
The value of tmnxL2tpLnsSePppStatTxIpcpCodeRj indicates the number of IPCP code rejects transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxIpv6cpCfRq 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.46
The value of tmnxL2tpLnsSePppStatRxIpv6cpCfRq indicates the number of IPv6 Control Protocol (IPv6CP) configure requests received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxIpv6cpCfAk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.47
The value of tmnxL2tpLnsSePppStatRxIpv6cpCfAk indicates the number of IPv6CP configure acknowledgements received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxIpv6cpCfNk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.48
The value of tmnxL2tpLnsSePppStatRxIpv6cpCfNk indicates the number of negative IPv6CP configure acknowledgements received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxIpv6cpCfRj 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.49
The value of tmnxL2tpLnsSePppStatRxIpv6cpCfRj indicates the number of IPv6CP configure rejects received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxIpv6cpTmRq 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.50
The value of tmnxL2tpLnsSePppStatRxIpv6cpTmRq indicates the number of IPv6CP terminate requests received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxIpv6cpTmAk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.51
The value of tmnxL2tpLnsSePppStatRxIpv6cpTmAk indicates the number of IPv6CP terminate acknowledgements received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatRxIpv6cpCdRj 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.52
The value of tmnxL2tpLnsSePppStatRxIpv6cpCdRj indicates the number of IPv6CP code rejects received for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxIpv6cpCfRq 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.53
The value of tmnxL2tpLnsSePppStatTxIpv6cpCfRq indicates the number of IPv6CP configure requests transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxIpv6cpCfAk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.54
The value of tmnxL2tpLnsSePppStatTxIpv6cpCfAk indicates the number of IPv6CP configure acknowledgements transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxIpv6cpCfNk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.55
The value of tmnxL2tpLnsSePppStatTxIpv6cpCfNk indicates the number of negative IPv6CP configure acknowledgements transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxIpv6cpCfRj 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.56
The value of tmnxL2tpLnsSePppStatTxIpv6cpCfRj indicates the number of IPv6CP configure rejects transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxIpv6cpTmRq 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.57
The value of tmnxL2tpLnsSePppStatTxIpv6cpTmRq indicates the number of IPv6CP terminate requests transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxIpv6cpTmAk 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.58
The value of tmnxL2tpLnsSePppStatTxIpv6cpTmAk indicates the number of IPv6CP terminate acknowledgements transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSePppStatTxIpv6cpCdRj 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.3.1.59
The value of tmnxL2tpLnsSePppStatTxIpv6cpCdRj indicates the number of IPv6CP code rejects transmitted for this PPP session.
Status: obsolete Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpLnsSeMRtTable 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.4
The tmnxL2tpLnsSeMRtTable contains managed routes for Layer Two Tunneling Protocol Sessions for which this system acts as LNS. This table is replaced with TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppMRtTable
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpLnsSeMRtEntry

tmnxL2tpLnsSeMRtEntry 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.4.1
Each conceptual row represents a managed route of an L2TP session for which this system acts as LNS.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpLnsSeMRtEntry  

tmnxL2tpLnsSeMRtAddrType 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.4.1.1
The value of tmnxL2tpLnsSeMRtAddrType indicates the address type of tmnxL2tpLnsSeMRtAddr.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  InetAddressType  

tmnxL2tpLnsSeMRtAddr 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.4.1.2
The value of tmnxL2tpLnsSeMRtAddr indicates the IP address of the managed route.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  InetAddress Size(4|16)  

tmnxL2tpLnsSeMRtPrefixLen 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.4.1.3
The value of tmnxL2tpLnsSeMRtPrefixLen indicates the prefix length of the subnet associated with tmnxL2tpLnsSeMRtAddr.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  InetAddressPrefixLength  

tmnxL2tpLnsSeMRtStatus 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.4.1.4
The value of tmnxL2tpLnsSeMRtStatus indicates the state of this managed route.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxManagedRouteStatus  

tmnxL2tpLnsSeOvrTable 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6
The tmnxL2tpLnsSeOvrTable contains QoS (Quality of Service) overrides for Layer Two Tunneling Protocol Sessions for which this system acts as LNS. This table is replaced with TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppOvrTable.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpLnsSeOvrEntry

tmnxL2tpLnsSeOvrEntry 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6.1
Each conceptual row represents QoS overrides information of an L2TP session for which this system acts as LNS.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpLnsSeOvrEntry  

tmnxL2tpLnsSeOvrDirection 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6.1.1
The value of tmnxL2tpLnsSeOvrDirection indicates if this row specifies ingress or egress qos override parameters.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  TDirection 1 | 2  

tmnxL2tpLnsSeOvrType 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6.1.2
The value of tmnxL2tpLnsSeOvrType indicates what field has been overridden by this row.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  TQosOverrideType  

tmnxL2tpLnsSeOvrTypeId 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6.1.3
The value of tmnxL2tpLnsSeOvrTypeId indicates the ID of the queue/policer that has been overridden by this row. If the value of tmnxL2tpLnsSeOvrType is not 'queue (1)' or 'policer (2)', this field must be set to zero (0).
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  Integer32  

tmnxL2tpLnsSeOvrTypeName 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6.1.4
The value of tmnxL2tpLnsSeOvrTypeName indicates the name of the scheduler/arbiter that has been overridden by this row. If the value of tmnxL2tpLnsSeOvrType is not 'arbiter (4)' or 'scheduler (5)', this field must be set to zero (0).
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxL2tpLnsSeOvrPIR 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6.1.5
The value of tmnxL2tpLnsSeOvrPIR indicates the PIR rate in kbps allowed for the object overridden by this row.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TPIRRateOverride  

tmnxL2tpLnsSeOvrCIR 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6.1.6
The value of tmnxL2tpLnsSeOvrCIR indicates the CIR rate in kbps allowed for the object overridden by this row.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TCIRRateOverride  

tmnxL2tpLnsSeOvrCBS 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6.1.7
The value of tmnxL2tpLnsSeOvrCBS indicates the amount of reserved buffer space (in bytes) for the object overridden by this row.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TBurstSizeBytesOverride  

tmnxL2tpLnsSeOvrMBS 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.6.1.8
The value of tmnxL2tpLnsSeOvrMBS indicates the maximum amount of reserved buffer space (in bytes) for the object overridden by this row.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TBurstSizeBytesOverride  

tmnxL2tpLnsSeAleTableLastCh 1.3.6.1.4.1.6527.3.1.2.60.1.21
The value of the object tmnxL2tpLnsSeAleTableLastCh indicates the value of sysUpTime at the time of the last update of an entry in the tmnxL2tpLnsSeAleTable.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpLnsSeAleTable 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.7
The tmnxL2tpLnsSeAleTable contains Access Loop Encapsulation information for Layer Two Tunneling Protocol Sessions for which this system acts as LNS. This table is replaced with TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubPppAleTable.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpLnsSeAleEntry

tmnxL2tpLnsSeAleEntry 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.7.1
Each conceptual row represents access loop encapsulation information of an L2TP session for which this system acts as LNS.
Status: obsolete Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpLnsSeAleEntry  


tmnxL2tpLnsSeAleEncaps1 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.7.1.2
The value of tmnxL2tpLnsSeAleEncaps1 indicates the encapsulation used by the subscriber host on the DSL access loop.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxAccessLoopEncaps1  

tmnxL2tpLnsSeAleEncaps2 1.3.6.1.4.1.6527.3.1.2.60.1.5.1.7.1.3
The value of tmnxL2tpLnsSeAleEncaps2 indicates the encapsulation used by the subscriber host on the DSL access loop.
Status: obsolete Access: read-only
OBJECT-TYPE    
  TmnxAccessLoopEncaps2  

tmnxL2tpSeStopTable 1.3.6.1.4.1.6527.3.1.2.60.1.5.2.1
The tmnxL2tpSeStopTable has an entry for each active Layer Two Tunneling Protocol Session.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpSeStopEntry

tmnxL2tpSeStopEntry 1.3.6.1.4.1.6527.3.1.2.60.1.5.2.1.1
Each conceptual row presents an operations interface to stop a Layer Two Tunneling Protocol session. Entries in this table are created and destroyed by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpSeStopEntry  

tmnxL2tpSeStop 1.3.6.1.4.1.6527.3.1.2.60.1.5.2.1.1.1
Setting this object to 'doAction (1)' triggers an attempt to stop the control connection for this L2TP session. Reading this object returns the value 'notApplicable'.
Status: current Access: read-write
OBJECT-TYPE    
  TmnxActionType  

tmnxL2tpLnsIsaGrpObjs 1.3.6.1.4.1.6527.3.1.2.60.1.6.1
OBJECT IDENTIFIER    

tmnxL2tpIsaGrpTableLastCh 1.3.6.1.4.1.6527.3.1.2.60.1.15
The value of the object tmnxL2tpIsaGrpTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpIsaGrpTable.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpIsaGrpTable 1.3.6.1.4.1.6527.3.1.2.60.1.6.1.1
The tmnxL2tpIsaGrpTable contains objects to configure L2TP Integrated Service Adaptor (ISA) Groups. The ISA Groups are used for the L2TP Network Server (LNS) function. An L2TP ISA group is used to represent multiple hardware adaptors as a single entity, allowing for load balancing between multiple L2TP ISA's.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpIsaGrpEntry

tmnxL2tpIsaGrpEntry 1.3.6.1.4.1.6527.3.1.2.60.1.6.1.1.1
Each conceptual row represents a Layer Two Tunneling Protocol Integrated Service Adaptor Group. Entries in this table can be created or deleted via SNMP operations.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpIsaGrpEntry  

tmnxL2tpIsaGrpId 1.3.6.1.4.1.6527.3.1.2.60.1.6.1.1.1.1
The value of the object tmnxL2tpIsaGrpId specifies the identifier of the L2TP Integrated Service Adaptor group.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpIsaGrpId  

tmnxL2tpIsaGrpRowStatus 1.3.6.1.4.1.6527.3.1.2.60.1.6.1.1.1.2
The value of tmnxL2tpIsaGrpRowStatus specifies the row status of this row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxL2tpIsaGrpLastMgmtChange 1.3.6.1.4.1.6527.3.1.2.60.1.6.1.1.1.3
The value of tmnxL2tpIsaGrpLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpIsaGrpDescription 1.3.6.1.4.1.6527.3.1.2.60.1.6.1.1.1.4
The value of tmnxL2tpIsaGrpDescription specifies the description of this L2TP ISA group.
Status: current Access: read-create
OBJECT-TYPE    
  TItemDescription  

tmnxL2tpIsaGrpAdminState 1.3.6.1.4.1.6527.3.1.2.60.1.6.1.1.1.5
The value of tmnxL2tpIsaGrpAdminState specifies the administrative state of this L2TP ISA group.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxAdminState  

tmnxL2tpIsaGrpOperState 1.3.6.1.4.1.6527.3.1.2.60.1.6.1.1.1.6
The value of tmnxL2tpIsaGrpOperState indicates the operational status of this L2TP ISA group.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxOperState  

tmnxL2tpIsaGrpPortPlcy 1.3.6.1.4.1.6527.3.1.2.60.1.6.1.1.1.8
The value of tmnxL2tpIsaGrpPortPlcy specifies the port policy of this L2TP ISA group. This object refers to a row in the TIMETRA-PORT-MIB::tmnxPortPlcyTable. If a port policy is associated with an L2TP ISA group, ports created for this group can take applicable configuration from that port policy.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxL2tpLnsIsaMdaObjs 1.3.6.1.4.1.6527.3.1.2.60.1.6.2
OBJECT IDENTIFIER    

tmnxL2tpIsaMdaTableLastCh 1.3.6.1.4.1.6527.3.1.2.60.1.16
The value of the object tmnxL2tpIsaMdaTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpIsaMdaTable.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpIsaMdaTable 1.3.6.1.4.1.6527.3.1.2.60.1.6.2.1
The tmnxL2tpIsaMdaTable contains objects to configure the L2TP ISA Group Media Dependent Adapters (MDA).
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpIsaMdaEntry

tmnxL2tpIsaMdaEntry 1.3.6.1.4.1.6527.3.1.2.60.1.6.2.1.1
Each conceptual row represents an L2TP ISA Media Dependent Adapter (MDA) of an L2TP ISA Group. Entries in this table can be created or deleted via SNMP operations.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpIsaMdaEntry  

tmnxL2tpIsaMdaRowStatus 1.3.6.1.4.1.6527.3.1.2.60.1.6.2.1.1.1
The value of tmnxL2tpIsaMdaRowStatus specifies the row status of this row.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxL2tpIsaMdaLastMgmtChange 1.3.6.1.4.1.6527.3.1.2.60.1.6.2.1.1.2
The value of tmnxL2tpIsaMdaLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpIsaMdaDrain 1.3.6.1.4.1.6527.3.1.2.60.1.6.2.1.1.3
The value of tmnxL2tpIsaMdaDrain specifies if this MDA is drained from LNS tunnels.
Status: current Access: read-create
OBJECT-TYPE    
  TruthValue  

tmnxL2tpIsaMdaStop 1.3.6.1.4.1.6527.3.1.2.60.1.6.2.1.1.4
Setting the value of tmnxL2tpIsaMdaStop to 'doAction' triggers an attempt to stop all PPP sessions on this L2TP ISA MDA. Reading the value of tmnxL2tpIsaMdaStop results in 'not-applicable'.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxActionType  

tmnxL2tpLnsIsaMdaStatObjs 1.3.6.1.4.1.6527.3.1.2.60.1.6.3
OBJECT IDENTIFIER    

tmnxL2tpIsaMdaStatTableLastCh 1.3.6.1.4.1.6527.3.1.2.60.1.17
The value of the object tmnxL2tpIsaMdaStatTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpIsaGrpTable.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpIsaMdaStatTable 1.3.6.1.4.1.6527.3.1.2.60.1.6.3.1
The tmnxL2tpIsaMdaStatTable contains status and statistics information about the Media Dependent Adapters (MDA) of an L2TP ISA Group.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpIsaMdaStatEntry

tmnxL2tpIsaMdaStatEntry 1.3.6.1.4.1.6527.3.1.2.60.1.6.3.1.1
Each conceptual row contains status and statistics information about a Media Dependent Adapter (MDA) of an L2TP ISA Group. Entries in this table are created and removed automatically by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpIsaMdaStatEntry  

tmnxL2tpIsaMdaStatOperState 1.3.6.1.4.1.6527.3.1.2.60.1.6.3.1.1.1
The value of tmnxL2tpIsaMdaStatOperState indicates the operational state of this L2TP ISA MDA.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpIsaMdaOperState  

tmnxL2tpIsaMdaStatSessions 1.3.6.1.4.1.6527.3.1.2.60.1.6.3.1.1.2
The value of tmnxL2tpIsaMdaStatOperState indicates the actual number of PPP sessions on this L2TP ISA MDA.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

tmnxL2tpIsaMdaVRtrTable 1.3.6.1.4.1.6527.3.1.2.60.1.6.3.2
The tmnxL2tpIsaMdaVRtrTable contains status information about the L2TP ISA Group Media Dependent Adapters (MDA) with respect to the associated Virtual Routers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpIsaMdaVRtrEntry

tmnxL2tpIsaMdaVRtrEntry 1.3.6.1.4.1.6527.3.1.2.60.1.6.3.2.1
Each conceptual row represents the association of an L2TP ISA Media Dependent Adapter (MDA) and a Virtual Router. Entries in this table are created and removed automatically by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpIsaMdaVRtrEntry  

tmnxL2tpIsaMdaVRtrOperState 1.3.6.1.4.1.6527.3.1.2.60.1.6.3.2.1.1
The value of tmnxL2tpIsaMdaVRtrOperState indicates the operational state of this L2TP ISA MDA with respect to this Virtual Router.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxOperState  

tmnxL2tpLnsIfObjs 1.3.6.1.4.1.6527.3.1.2.60.1.7.1
OBJECT IDENTIFIER    

tmnxL2tpLnsIfTable 1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1
This table is supported for backwards compatibility; the recommended way to configure L2TP LNS Group-Interfaces is by means of the TIMETRA-SERV-MIB::svcIfSapCfgTable. The tmnxL2tpLnsIfTable contains objects to configure L2TP LNS Group-Interfaces. Entries in this table are created and destroyed by the system. The system automatically creates an entry in this table for each entry in the TIMETRA-SERV-MIB::iesIfTable where the value of iesIfType is equal to 'group' and the value of iesIfGroupInterfaceType is equal to 'lns'. Deletion of such a row in the iesIfTable results in the same fate for the corresponding row in this table.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpLnsIfEntry

tmnxL2tpLnsIfEntry 1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1
L2TP LNS specific information about a specific group interface. Unlike regular subscriber traffic, that enters the system through Service Access Points (SAP) on a group-interface, traffic for PPP subscriber sessions terminated by the LNS function, enters the system through a plain layer 3 interface; this traffic is relayed for processing to an L2TP ISA MDA; it re-enters through an internal LNS group interface; this entry allows to configure subscriber management parameters for PPP subscriber sessions.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpLnsIfEntry  

tmnxL2tpLnsIfLastMgmtChange 1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1.1
The value of tmnxL2tpLnsIfLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this table row.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpLnsIfDescription 1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1.2
The value of tmnxL2tpLnsIfDescription specifies the description of this L2TP LNS interface.
Status: current Access: read-create
OBJECT-TYPE    
  TItemDescription  

tmnxL2tpLnsIfDefSubProfile 1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1.3
The value of tmnxL2tpLnsIfDefSubProfile specifies the default subscriber profile of the subscribers of this LNS interface.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxL2tpLnsIfDefSlaProfile 1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1.4
The value of tmnxL2tpLnsIfDefSlaProfile specifies the default SLA profile of the subscribers of this LNS interface.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxL2tpLnsIfDefAppProfile 1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1.5
The value of tmnxL2tpLnsIfDefSlaProfile specifies the default application profile of the subscribers of this LNS interface.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxL2tpLnsIfSubIdentPolicy 1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1.6
The value of tmnxL2tpLnsIfSubIdentPolicy specifies the subscriber identification policy of the subscribers of this LNS interface.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxL2tpLnsIfDefSubIdent 1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1.7
The value of tmnxL2tpLnsIfDefSubIdent specifies the default subscriber identification of the subscribers of this LNS interface. This value is used in case no other source (like Radius) provides a subscriber identification string. If the value of this object is set to 'useSapId', the SAP-id will be used as the default subscriber identification string; in this case, tmnxL2tpLnsIfDefSubIdentString must contain the empty string, so any non-empty string in tmnxL2tpLnsIfDefSubIdentString will be set to an empty string. If the value of this object is set to 'useAutoId', the auto-generated subscriber identification string, as defined in tmnxSubMgmtAutoSubIdObjs, is used as the default subscriber identification string. In this case, tmnxL2tpLnsIfDefSubIdentString must contain the empty string, so any non-empty string in tmnxL2tpLnsIfDefSubIdentString will be set to an empty string. If the value of this object is set to 'useString', the value of tmnxL2tpLnsIfDefSubIdentString will be used as the default subscriber identification string; in this case, an empty tmnxL2tpLnsIfDefSubIdentString means that there is no default subscriber identification configured.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxDefSubIdSource  

tmnxL2tpLnsIfDefSubIdentString 1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1.8
The value of tmnxL2tpLnsIfDefSubIdentString specifies the default subscriber identification string applicable on the subscribers of this LNS interface.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..32)  

tmnxL2tpLnsIfDefFilterProfile 1.3.6.1.4.1.6527.3.1.2.60.1.7.1.1.1.9
The value of the object tmnxL2tpLnsIfDefFilterProfile specifies the default filter profile for this LNS interface. The specified filter profile needs to exists in the TIMETRA-SUBSCRIBER-MGMT-MIB::tmnxSubFilterProfileTable.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxL2tpLacMlpppBundleTable 1.3.6.1.4.1.6527.3.1.2.60.1.8.1
The tmnxL2tpLacMlpppBundleTable allows monitoring of MLPPP (Multi Link PPP) bundles of PPP sessions where this system acts as a LAC.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpLacMlpppBundleEntry

tmnxL2tpLacMlpppBundleEntry 1.3.6.1.4.1.6527.3.1.2.60.1.8.1.1
Each conceptual row represents an MLPPP Bundle associated with PPP sessions for which this system acts as a LAC. Entries in this table are created and destroyed by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpLacMlpppBundleEntry  

tmnxL2tpLacMlpppBundleIndex 1.3.6.1.4.1.6527.3.1.2.60.1.8.1.1.1
The value of the object tmnxL2tpLacMlpppBundleIndex indicates the local identifier of this MLPPP Bundle.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32  

tmnxL2tpLacMlpppBundleSvcId 1.3.6.1.4.1.6527.3.1.2.60.1.8.1.1.2
The value of tmnxL2tpLacMlpppBundleSvcId indicates the service ID of the IES/VPRN service to which this MLPPP bundle belongs.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxServId  

tmnxL2tpLacMlpppBundleFwdTuId 1.3.6.1.4.1.6527.3.1.2.60.1.8.1.1.3
The value of tmnxL2tpLacMlpppBundleFwdTuId indicates the LTS (L2TP Tunnel Stitching) tunnel ID if this bundle is associated with PPP sessions that are stitched to another L2TP tunnel. Otherwise, the value of tmnxL2tpLacMlpppBundleFwdTuId is equal to zero.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpTunnelId  

tmnxL2tpLacMlpppBundleUserName 1.3.6.1.4.1.6527.3.1.2.60.1.8.1.1.4
The value of tmnxL2tpLacMlpppBundleUserName indicates the user name of the subscriber associated with this MLPPP bundle, or another string used to identify that subscriber.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxPppoeUserNameOrEmpty  

tmnxL2tpLacMlpppBundleLocEpClass 1.3.6.1.4.1.6527.3.1.2.60.1.8.1.1.5
The value of tmnxL2tpLacMlpppBundleLocEpClass indicates the address class of the local endpoint. If the value of tmnxL2tpLacMlpppBundleLocEpClass is equal to 'null', the address class of the MLPPP Endpoint Discriminator option was not present in a received Configure-Request.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxMlpppEpClass  

tmnxL2tpLacMlpppBundleLocEpAddr 1.3.6.1.4.1.6527.3.1.2.60.1.8.1.1.6
The value of tmnxL2tpLacMlpppBundleLocEpAddr indicates the address of the local MLPPP Endpoint. Its interpretation depends on the value of tmnxL2tpLacMlpppBundleLocEpClass.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..20)  

tmnxL2tpLacMlpppBundleRemEpClass 1.3.6.1.4.1.6527.3.1.2.60.1.8.1.1.7
The value of tmnxL2tpLacMlpppBundleRemEpClass indicates the address class of the local endpoint. If the value of tmnxL2tpLacMlpppBundleRemEpClass is equal to 'null', the address class of the MLPPP Endpoint Discriminator option was not present in a received Configure-Request.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxMlpppEpClass  

tmnxL2tpLacMlpppBundleRemEpAddr 1.3.6.1.4.1.6527.3.1.2.60.1.8.1.1.8
The value of tmnxL2tpLacMlpppBundleRemEpAddr indicates the address of the local MLPPP Endpoint. Its interpretation depends on the value of tmnxL2tpLacMlpppBundleRemEpClass.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..20)  

tmnxL2tpLacMlpppLinkTable 1.3.6.1.4.1.6527.3.1.2.60.1.8.2
The tmnxL2tpLacMlpppLinkTable contains the subscriber MLPPP (Multi Link PPP) links where this system acts as a LAC, ordered per bundle.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpLacMlpppLinkEntry

tmnxL2tpLacMlpppLinkEntry 1.3.6.1.4.1.6527.3.1.2.60.1.8.2.1
Each conceptual row represents an MLPPP Link associated with a PPP session for which this system acts as a LAC. Entries in this table are created and destroyed by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpLacMlpppLinkEntry  

tmnxL2tpLacMlpppLinkState 1.3.6.1.4.1.6527.3.1.2.60.1.8.2.1.1
The value of tmnxL2tpLacMlpppLinkState indicates the operational state of the session associated with this MLPPP link.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxL2tpSeOperState  

tmnxL2tpApTable 1.3.6.1.4.1.6527.3.1.2.60.1.100.1
The tmnxL2tpApTable allows configuration of RADIUS based accounting policies for L2TP (Layer Two Tunneling Protocol) tunnel accounting.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpApEntry

tmnxL2tpApEntry 1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1
Each entry represents the configuration for an L2TP RADIUS Accounting Policy. Entries in this table can be created and deleted via SNMP SET operations to tmnxL2tpApRowStatus.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpApEntry  

tmnxL2tpApName 1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.1
The value of tmnxL2tpApName specifies the name of an L2TP RADIUS Accounting Policy.
Status: current Access: not-accessible
OBJECT-TYPE    
  TNamedItem  

tmnxL2tpApRowStatus 1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.2
The value of tmnxL2tpApRowStatus controls the creation and deletion of rows in the table. An attempt to delete a row that is referred to will fail with an inconsistentValue error.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxL2tpApLastMgmtChange 1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.3
The value of tmnxL2tpApLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this policy.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpApDescription 1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.4
The value of tmnxL2tpApDescription specifies the user provided description of this policy.
Status: current Access: read-create
OBJECT-TYPE    
  TItemDescription  

tmnxL2tpApType 0.1.1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.5
The value of tmnxL2tpApType specifies the type of accounting for the L2TP tunnels associated with this policy.
Status: current Access: read-create
OBJECT-TYPE    
  BITS session(0), tunnel(1)  

tmnxL2tpApServerVRtrID 1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.6
The value of tmnxL2tpApServerVRtrID specifies the virtual router instance applicable for the set of configured RADIUS servers (tmnxL2tpApRadServTable). The value of this object cannot be changed once a RADIUS server is configured for this policy. When the value is '0', both base and management router instances are available.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxVRtrIDOrZero  

tmnxL2tpApServerAlgorithm 1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.7
The value of tmnxL2tpApServerAlgorithm specifies the algorithm used to select a RADIUS server from the list of configured servers (tmnxL2tpApRadServTable).
Status: current Access: read-create
OBJECT-TYPE    
  TmnxSubRadServAlgorithm direct(1), roundRobin(2)  

tmnxL2tpApServerRetry 1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.8
The value of tmnxL2tpApServerRetry specifies the number of RADIUS requests towards the same RADIUS server.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..10  

tmnxL2tpApServerSrcAddrType 1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.9
The value of tmnxL2tpApServerSrcAddrType specifies the type of address stored in tmnxL2tpApServerSrcAddr.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

tmnxL2tpApServerSrcAddr 1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.10
The value of tmnxL2tpApServerSrcAddr specifies the source address of a RADIUS packet for L2TP accounting; it must be a valid unicast address (otherwise a wrongValue error is returned). If this object is configured with the address of a router interface (ref TIMETRA-VRTR-MIB::vRiaIpAddress) the RADIUS client uses it while making a request to the server. If the address is not configured or is not the address of one of the interfaces, the source address is based on the address of the RADIUS server; if the server address is in-band, the client uses the system IP address; if it is out-of-band, the source address is the address of the management interface (the addresses can be found in TIMETRA-VRTR-MIB::vRiaIpAddress).
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress Size(0|4|16)  

tmnxL2tpApServerTimeout 1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.11
The value of tmnxL2tpApServerTimeout specifies the timeout between retries towards the same RADIUS server.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..90  

tmnxL2tpApIncludeAttributes 1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.12
The value of tmnxL2tpApIncludeAttributes specifies what RADIUS attributes the system should include into RADIUS accounting messages.
Status: current Access: read-create
OBJECT-TYPE    
  BITS nasIdentifier(0), nasPort(1), nasPortId(2), nasPortType(3)  

tmnxL2tpApRequestScriptPlcy 1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.13
The value of tmnxL2tpApRequestScriptPlcy specifies the RADIUS script policy used to change the RADIUS attributes of the outgoing Accounting-Request messages.
Status: current Access: read-create
OBJECT-TYPE    
  TNamedItemOrEmpty  

tmnxL2tpApNasPortIdPfixType 1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.14
The value of tmnxL2tpApNasPortIdPfixType specifies what type of prefix will be added to the NAS-Port-Id attribute if included in RADIUS accounting-request messages. This field is only applicable if the 'nasPortId' bit is set in tmnxL2tpApIncludeAttributes.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxSubNasPortPrefixType  

tmnxL2tpApNasPortIdPfixString 1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.15
The value of tmnxL2tpApNasPortIdPfixString specifies the user configurable string to be added as prefix to the NAS-Port-Id attribute if included in RADIUS accounting-request messages. This field is only applicable if the 'nasPortId' bit is set in tmnxL2tpApIncludeAttributes and tmnxL2tpApNasPortIdPfixType is set to 'userString'.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0..8)  

tmnxL2tpApNasPortIdSfixType 1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.16
The value of tmnxL2tpApNasPortIdSfixType specifies what type of suffix will be added to the NAS-Port-Id attribute if included in RADIUS accounting-request messages. This field is only applicable if the 'nasPortId' bit is set in tmnxL2tpApIncludeAttributes.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxSubNasPortSuffixType  

tmnxL2tpApNasPortTypeType 1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.17
The value of tmnxL2tpApNasPortTypeType specifies what kind of value will be put in the RADIUS NAS-Port-Type attribute if included in RADIUS accounting-request messages. This field is only applicable if the 'nasPortType' bit is set in tmnxL2tpApIncludeAttributes.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxSubNasPortTypeType  

tmnxL2tpApNasPortTypeValue 1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.18
The value of tmnxL2tpApNasPortTypeValue specifies what value will be put in the RADIUS NAS-Port-Type attribute if included in RADIUS accounting-request messages. This field is only applicable if the 'nasPortType' bit is set in tmnxL2tpApIncludeAttributes and the value of the object tmnxL2tpApNasPortTypeType is equal to 'config'.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 0..255  

tmnxL2tpApNasPortBitspec 1.3.6.1.4.1.6527.3.1.2.60.1.100.1.1.19
The value of tmnxL2tpApNasPortBitspec specifies what number will be put in the RADIUS NAS-Port attribute if included in RADIUS accounting-request messages. This field is only applicable if the 'nasPort' bit is set in tmnxL2tpApIncludeAttributes. ::= 'o' | 'i' | 's' | 'm' | 'p' | 'v' | 'c' 'c' - ATM VCI (Virtual Channel Identifier) 'i' - inner VLAN ID 'm' - MDA number 'o' - outer VLAN ID 'p' - port number 's' - slot number 'v' - ATM VPI (Virtual Path Identifier) Maximum 32 bits can be specified. If less than 32 bits are specified, the least significant bits are used and the omitted higher bits are set to zero. Example: *12o*12i*2s01 means 'the 12 least significant bits of the outer VLAN ID, followed by the 12 least significant bits of the inner VLAN ID, followed by the two least significant bits of the slot number, followed by a zero and a one-bit', stored in network order in the least significant bits: 0000ooooooooooooiiiiiiiiiiiiss01.
Status: current Access: read-create
OBJECT-TYPE    
  TmnxBinarySpecification  

tmnxL2tpApServTable 1.3.6.1.4.1.6527.3.1.2.60.1.100.2
The tmnxL2tpApServTable allows the configuration of objects related to a particular RADIUS server associated with a particular L2TP RADIUS Accounting Policy.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpApServEntry

tmnxL2tpApServEntry 1.3.6.1.4.1.6527.3.1.2.60.1.100.2.1
Each entry represents the configuration for a particular RADIUS server. Entries in this table can be created and deleted via SNMP SET operations to tmnxL2tpApServRowStatus.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpApServEntry  

tmnxL2tpApServIndex 1.3.6.1.4.1.6527.3.1.2.60.1.100.2.1.1
The value of tmnxL2tpApServIndex specifies the index of this RADIUS server in the set of servers associated with this L2TP accounting policy.
Status: current Access: not-accessible
OBJECT-TYPE    
  Unsigned32 1..5  

tmnxL2tpApServRowStatus 1.3.6.1.4.1.6527.3.1.2.60.1.100.2.1.2
The value of tmnxL2tpApServRowStatus controls the creation and deletion of rows in the table.
Status: current Access: read-create
OBJECT-TYPE    
  RowStatus  

tmnxL2tpApServLastMgmtChange 1.3.6.1.4.1.6527.3.1.2.60.1.100.2.1.3
The value tmnxL2tpApServLastMgmtChange indicates the sysUpTime at the time of the most recent management-initiated change to this conceptual row.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpApServAddrType 1.3.6.1.4.1.6527.3.1.2.60.1.100.2.1.5
The value of tmnxL2tpApServAddrType specifies the type of address stored in tmnxL2tpApServAddr.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddressType  

tmnxL2tpApServAddr 1.3.6.1.4.1.6527.3.1.2.60.1.100.2.1.6
The value of tmnxL2tpApServAddr specifies the IP address of the RADIUS server. A valid unicast IP address must be specified at row creation time.
Status: current Access: read-create
OBJECT-TYPE    
  InetAddress Size(4|16)  

tmnxL2tpApServSecret 1.3.6.1.4.1.6527.3.1.2.60.1.100.2.1.7
The value of tmnxL2tpApServSecret specifies the secret key associated with the RADIUS server. A non-empty value must be specified at row creation time. An SNMP get request on this object always returns an empty string.
Status: current Access: read-create
OBJECT-TYPE    
  DisplayString Size(0|1..20)  

tmnxL2tpApServAcctPort 1.3.6.1.4.1.6527.3.1.2.60.1.100.2.1.8
The value of tmnxL2tpApServAcctPort specifies the UDP port number on which to contact the RADIUS server for accounting.
Status: current Access: read-create
OBJECT-TYPE    
  Unsigned32 1..65535  

tmnxL2tpApServOperState 1.3.6.1.4.1.6527.3.1.2.60.1.100.2.1.9
The value of tmnxL2tpApServOperState indicates the operational state of the RADIUS server.
Status: current Access: read-only
OBJECT-TYPE    
  TmnxOperState  

tmnxL2tpApServStatsTable 1.3.6.1.4.1.6527.3.1.2.60.1.100.3
The tmnxL2tpApServStatsTable presents statistics of l2tp-accounting-policies' RADIUS servers.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TmnxL2tpApServStatsEntry

tmnxL2tpApServStatsEntry 1.3.6.1.4.1.6527.3.1.2.60.1.100.3.1
Each row represents statistics about a specific server of a specify L2TP accounting policy. Rows in this table are created automatically by the system.
Status: current Access: not-accessible
OBJECT-TYPE    
  TmnxL2tpApServStatsEntry  

tmnxL2tpApServStatsTxRequests 1.3.6.1.4.1.6527.3.1.2.60.1.100.3.1.1
The value of tmnxL2tpApServStatsTxRequests indicates the number of RADIUS request packets transmitted for this server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpApServStatsRxResponses 1.3.6.1.4.1.6527.3.1.2.60.1.100.3.1.2
The value of tmnxL2tpApServStatsRxResponses indicates the number of RADIUS response packets received from this server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpApServStatsReqTimeout 1.3.6.1.4.1.6527.3.1.2.60.1.100.3.1.3
The value of tmnxL2tpApServStatsReqTimeout indicates the number of RADIUS requests that have timed out for this server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpApServStatsReqSendFail 1.3.6.1.4.1.6527.3.1.2.60.1.100.3.1.4
The value of tmnxL2tpApServStatsReqSendFail indicates the number of RADIUS request packets that could not be transmitted for this server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpApServStatsReqPending 1.3.6.1.4.1.6527.3.1.2.60.1.100.3.1.5
The value of tmnxL2tpApServStatsReqPending indicates the number of RADIUS requests that are currently pending for this server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpApServStatsRespInvAuth 1.3.6.1.4.1.6527.3.1.2.60.1.100.3.1.6
The value of tmnxL2tpApServStatsRespInvAuth indicates the number of RADIUS response packets with an invalid Authenticator received from this server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpApServStatsSendRetries 1.3.6.1.4.1.6527.3.1.2.60.1.100.3.1.7
The value of tmnxL2tpApServStatsSendRetries indicates the number of retries to a different server for a single accounting request for this connection with this RADIUS server.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

tmnxL2tpApTableLastCh 1.3.6.1.4.1.6527.3.1.2.60.1.100.100
The value of the object tmnxL2tpApTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpApTable.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpApServTableLastCh 1.3.6.1.4.1.6527.3.1.2.60.1.100.101
The value of the object tmnxL2tpApServTableLastCh indicates the value of sysUpTime at the time of the last modification of an entry in the tmnxL2tpApServTable.
Status: current Access: read-only
OBJECT-TYPE    
  TimeStamp  

tmnxL2tpNotifyDescription 1.3.6.1.4.1.6527.3.1.2.60.2.1
The object tmnxL2tpNotifyDescription is a printable character string.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  DisplayString  

tmnxL2tpPppNcpFailureProtocol 1.3.6.1.4.1.6527.3.1.2.60.2.20
The value of tmnxL2tpPppNcpFailureProtocol indicates the failing NCP protocol.
Status: current Access: accessible-for-notify
OBJECT-TYPE    
  TmnxPppNcpProtocol  

tmnxL2tpPeerUnreachable 1.3.6.1.4.1.6527.3.1.3.60.0.1
The tmnxL2tpPeerUnreachable notification is sent when an L2TP peer becomes unreachable and when it becomes reachable again.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

tmnxL2tpIsaMdaVRtrStateChange 1.3.6.1.4.1.6527.3.1.3.60.0.2
The tmnxL2tpIsaMdaVRtrStateChange notification is sent when the operational state of an L2TP ISA MDA with respect to a Virtual Router changes.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

tmnxL2tpLnsSePppSessionFailure 1.3.6.1.4.1.6527.3.1.3.60.0.3
The tmnxL2tpLnsSePppSessionFailure notification is sent when the system could not create a new session in the tmnxL2tpLnsSePppTable.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

tmnxL2tpLnsPppNcpFailure 1.3.6.1.4.1.6527.3.1.3.60.0.10
The tmnxL2tpLnsPppNcpFailure notification indicates that there is a NCP phase setup problem.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

tmnxL2tpApFailure 1.3.6.1.4.1.6527.3.1.3.60.0.11
The tmnxL2tpApFailure notification is generated when a RADIUS accounting request was not sent out successfully to any of the RADIUS servers in the indicated accounting policy.
Status: current Access: accessible-for-notify
NOTIFICATION-TYPE    

tmnxL2tpCfgGroup 1.3.6.1.4.1.6527.3.1.1.60.2.1
The group of objects providing management of L2TP instances on Alcatel-Lucent SROS series systems.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpTgCfgGroup 1.3.6.1.4.1.6527.3.1.1.60.2.2
The group of objects providing management of L2TP tunnel groups on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpTuCfgGroup 1.3.6.1.4.1.6527.3.1.1.60.2.3
The group of objects providing management of L2TP tunnels on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpStatGroup 1.3.6.1.4.1.6527.3.1.1.60.2.4
The group of objects providing monitoring of L2TP on Alcatel-Lucent SROS series systems.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpStatV8v0Group 1.3.6.1.4.1.6527.3.1.1.60.2.21
The group of objects providing monitoring of L2TP on Alcatel-Lucent SROS series systems release 8.0.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpTgStatGroup 1.3.6.1.4.1.6527.3.1.1.60.2.5
The group of objects providing monitoring of L2TP tunnel groups on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpTuStatGroup 1.3.6.1.4.1.6527.3.1.1.60.2.18
The group of objects providing monitoring of L2TP tunnels on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpPeerStatGroup 1.3.6.1.4.1.6527.3.1.1.60.2.7
The group of objects providing monitoring of L2TP peers on Alcatel-Lucent SROS series systems.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpPeerStatV8v0Group 1.3.6.1.4.1.6527.3.1.1.60.2.19
The group of objects providing monitoring of L2TP peers on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpSeStatGroup 1.3.6.1.4.1.6527.3.1.1.60.2.8
The group of objects providing monitoring of L2TP sessions on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpPeerOpGroup 1.3.6.1.4.1.6527.3.1.1.60.2.9
The group of objects providing monitoring of L2TP peers on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpTgOpGroup 1.3.6.1.4.1.6527.3.1.1.60.2.10
The group of objects providing operations on L2TP tunnel groups on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpTuOpGroup 1.3.6.1.4.1.6527.3.1.1.60.2.11
The group of objects providing operations on L2TP tunnels on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpLnsIsaGroup 1.3.6.1.4.1.6527.3.1.1.60.2.12
The group of objects providing configuration of L2TP Integrated Service Adaptors (ISA) on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpLnsIsaStatGroup 1.3.6.1.4.1.6527.3.1.1.60.2.13
The group of objects providing monitoring of L2TP Integrated Service Adaptors (ISA) on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpLnsTgGroup 1.3.6.1.4.1.6527.3.1.1.60.2.14
The group of objects providing management of L2TP LNS tunnel groups on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpLnsTuGroup 1.3.6.1.4.1.6527.3.1.1.60.2.15
The group of objects providing management of L2TP LNS tunnels on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpLnsSeGroup 1.3.6.1.4.1.6527.3.1.1.60.2.16
The group of objects providing monitoring of L2TP LNS PPP sessions on Alcatel-Lucent SROS series systems.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpCfgV8v0Group 1.3.6.1.4.1.6527.3.1.1.60.2.17
The group of objects providing management of L2TP instances on Alcatel-Lucent SROS series systems release 8.0.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpLnsIfGroup 1.3.6.1.4.1.6527.3.1.1.60.2.20
The group of objects providing configuration of L2TP LNS group interfaces on Alcatel-Lucent SROS series systems.
Status: obsolete Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpSeOpGroup 1.3.6.1.4.1.6527.3.1.1.60.2.22
The group of objects providing operations on L2TP sessions on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpLnsTgV9v0Group 1.3.6.1.4.1.6527.3.1.1.60.2.30
The group of objects providing management of L2TP LNS tunnel groups on Alcatel-Lucent SROS series systems that were added in release 9.0.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpLnsTuV9v0Group 1.3.6.1.4.1.6527.3.1.1.60.2.31
The group of objects providing management of L2TP LNS tunnels on Alcatel-Lucent SROS series systems that were added in release 9.0.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpLnsIfV9v0Group 1.3.6.1.4.1.6527.3.1.1.60.2.32
The group of objects providing configuration of L2TP LNS group interfaces on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpMlpppGroup 1.3.6.1.4.1.6527.3.1.1.60.2.40
The group of objects providing management of MLPPP for L2TP tunnels on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpLnsSeV9v0Group 1.3.6.1.4.1.6527.3.1.1.60.2.41
The group of objects providing monitoring of L2TP LNS PPP sessions in release 9.0 of Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpFilterProfileV9v0Group 1.3.6.1.4.1.6527.3.1.1.60.2.42
The group of objects providing configuration of Filter Profiles on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpTgV10v0Group 1.3.6.1.4.1.6527.3.1.1.60.2.43
The group of objects providing management of L2TP LNS tunnel groups on Alcatel-Lucent SROS series systems that were added in release 10.0.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpTuV10v0Group 1.3.6.1.4.1.6527.3.1.1.60.2.44
The group of objects providing management of L2TP LNS tunnels on Alcatel-Lucent SROS series systems that were added in release 10.0.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpAccountingGroup 1.3.6.1.4.1.6527.3.1.1.60.2.45
The group of objects providing management of RADIUS accounting for L2TP tunnels on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpLnsIsaV10v0Group 1.3.6.1.4.1.6527.3.1.1.60.2.46
The group of objects providing configuration of L2TP Integrated Service Adaptors (ISA) added in release 10.0 of Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpObsoletedObjsV9v0Group 1.3.6.1.4.1.6527.3.1.1.60.2.97
The group of objects that were obsoleted in release 9.0 of Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpObsoletedObjsV8v0Group 1.3.6.1.4.1.6527.3.1.1.60.2.98
The group of objects that were obsoleted in release 8.0 of Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpNotifyObjsGroup 1.3.6.1.4.1.6527.3.1.1.60.2.99
The group of notification objects supporting L2TP notifications on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpNotifyObjsV9v0Group 1.3.6.1.4.1.6527.3.1.1.60.2.102
The group of notification objects supporting L2TP notifications on Alcatel-Lucent SROS series systems added in release 9.0.
Status: current Access: accessible-for-notify
OBJECT-GROUP    

tmnxL2tpNotifyGroup 1.3.6.1.4.1.6527.3.1.1.60.2.100
The group of notifications supporting L2TP on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

tmnxL2tpNotifyV9v0Group 1.3.6.1.4.1.6527.3.1.1.60.2.101
The group of notifications supporting L2TP on Alcatel-Lucent SROS series systems added in release 9.0.
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

tmnxL2tpNotifyV10v0Group 1.3.6.1.4.1.6527.3.1.1.60.2.103
The group of notifications supporting L2TP on Alcatel-Lucent SROS series systems added in release 10.0.
Status: current Access: accessible-for-notify
NOTIFICATION-GROUP    

tmnxL2tpCompliance 1.3.6.1.4.1.6527.3.1.1.60.1.1
The compliance statement for management of L2TP on Alcatel-Lucent SROS series systems.
Status: obsolete Access: accessible-for-notify
MODULE-COMPLIANCE    

tmnxL2tpStatCompliance 1.3.6.1.4.1.6527.3.1.1.60.1.2
The compliance statement for monitoring of L2TP on Alcatel-Lucent SROS series systems.
Status: obsolete Access: accessible-for-notify
MODULE-COMPLIANCE    

tmnxL2tpOpCompliance 1.3.6.1.4.1.6527.3.1.1.60.1.3
The compliance statement for L2TP operations on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

tmnxL2tpLnsCompliance 1.3.6.1.4.1.6527.3.1.1.60.1.4
The compliance statement for management of L2TP LNS on Alcatel-Lucent SROS series systems.
Status: obsolete Access: accessible-for-notify
MODULE-COMPLIANCE    

tmnxL2tpNotifyCompliance 1.3.6.1.4.1.6527.3.1.1.60.1.5
The compliance statement for L2TP notifications on Alcatel-Lucent SROS series systems.
Status: obsolete Access: accessible-for-notify
MODULE-COMPLIANCE    

tmnxL2tpV8v0Compliance 1.3.6.1.4.1.6527.3.1.1.60.1.6
The compliance statement for management of L2TP on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

tmnxL2tpStatV8v0Compliance 1.3.6.1.4.1.6527.3.1.1.60.1.7
The compliance statement for monitoring of L2TP on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

tmnxL2tpLnsV9v0Compliance 1.3.6.1.4.1.6527.3.1.1.60.1.10
The compliance statement for management of L2TP LNS on Alcatel-Lucent SROS series systems.
Status: obsolete Access: accessible-for-notify
MODULE-COMPLIANCE    

tmnxL2tpNotifyV9v0Compliance 1.3.6.1.4.1.6527.3.1.1.60.1.11
The compliance statement for L2TP notifications on Alcatel-Lucent SROS series systems.
Status: obsolete Access: accessible-for-notify
MODULE-COMPLIANCE    

tmnxL2tpMlpppCompliance 1.3.6.1.4.1.6527.3.1.1.60.1.12
The compliance statement for management of MLPPP (Multi Link Point to Point Protocol) for L2TP on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

tmnxL2tpV10v0Compliance 1.3.6.1.4.1.6527.3.1.1.60.1.13
The compliance statement for management of L2TP on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

tmnxL2tpNotifyV10v0Compliance 1.3.6.1.4.1.6527.3.1.1.60.1.14
The compliance statement for L2TP notifications on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

tmnxL2tpLnsV10v0Compliance 1.3.6.1.4.1.6527.3.1.1.60.1.15
The compliance statement for management of L2TP LNS on Alcatel-Lucent SROS series systems.
Status: current Access: accessible-for-notify
MODULE-COMPLIANCE    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor