SW-COMMON-MIB

File: SW-COMMON-MIB.mib (12504 bytes)

Imported modules

RFC-1212 RFC1155-SMI

Imported symbols

OBJECT-TYPE enterprises

Defined Types

SwL2DevAlarmPowerEntry  
SEQUENCE    
  swL2DevAlarmPowerIndex INTEGER
  swL2DevAlarmPowerTemperature INTEGER
  swL2DevAlarmPowerVolt INTEGER
  swL2DevAlarmPowerCurrent INTEGER
  swL2DevAlarmPowerFan INTEGER

SwL2DevAlarmSystemFanEntry  
SEQUENCE    
  swL2DevAlarmSystemFanIndex INTEGER
  swL2DevAlarmSystemFanState INTEGER

Defined Values

marconi 1.3.6.1.4.1.326
OBJECT IDENTIFIER    

systems 1.3.6.1.4.1.326.2
OBJECT IDENTIFIER    

external 1.3.6.1.4.1.326.2.20
OBJECT IDENTIFIER    


dlinkcommon 1.3.6.1.4.1.326.2.20.1.1
OBJECT IDENTIFIER    

golf 1.3.6.1.4.1.326.2.20.1.2
OBJECT IDENTIFIER    

golfproducts 1.3.6.1.4.1.326.2.20.1.2.1
OBJECT IDENTIFIER    

es2000 1.3.6.1.4.1.326.2.20.1.2.1.3
OBJECT IDENTIFIER    

golfcommon 1.3.6.1.4.1.326.2.20.1.2.2
OBJECT IDENTIFIER    

marconi-mgmt 1.3.6.1.4.1.326.2.20.1.2.2.2
OBJECT IDENTIFIER    

es2000Mgmt 1.3.6.1.4.1.326.2.20.1.2.2.2.28
OBJECT IDENTIFIER    

swL2Mgmt 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2
OBJECT IDENTIFIER    

swL2DevMgmt 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1
OBJECT IDENTIFIER    

swL2DevCtrl 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.1
OBJECT IDENTIFIER    

swL2DevCtrlStpState 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.1.1
This object can be enabled or disabled spanning tree algorithm during runtime of the system.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2DevCtrlPartitionModeState 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.1.2
This object used to enable or disable port auto partition. When the object apply for all ports of the device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2DevCtrlTableLockState 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.1.3
This object indicates whether the address table is locked. In other words, the address table doesn't learn any more new address. The aging timer is suspended when the address table is locked. As long as the table is locked, all of the frames are dropped if the destination can not be found in the address.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2DevCtrlHOLState 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.1.4
The object provides a way to prevent HOL (Head Of Line) blocking between ports. HOL protection may prevent forwarding a packet to a blocking port. The idea relies on the assumption that it is better to discard packets destined to blocking ports, then to let them consume more and more buffers in the input-port's Rx-counters because eventually these input ports may become totally blocked. The meanings of the values are: other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disabled(2) - HOL function disable for device. enabled(3) - HOL function enable for device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2DevCtrlAddrLookupModesAndHitRate 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.1.5
According to the differnet address looke mode setting, to enlarge the address table size is possible in device. But there is side effect as the higher level you have, the lower thorughput device has. That means Level 0 get the smallest table size, but get better performace. We recommand the user use the Level 1 as defualt setting.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER level0(1), level1(2), level2(3), level3(4), level4(5), level5(6), level6(7), level7(8)  

swL2DevCtrlBuzzerState 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.1.6
Controls buzzer state to be disabled or enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3)  

swL2DevCtrlBuzzerTest 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.1.7
Tests buzzer to bibi. First of all, any unsigned integer can be used to set.
Status: mandatory Access: write-only
OBJECT-TYPE    
  INTEGER  

swL2DevAlarm 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2
OBJECT IDENTIFIER    

swL2DevAlarmPartition 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.1
Depending on this object, the device send a trap or not when any one of the device's ports was partitioned.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2DevAlarmNewRoot 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.2
When the device has become the new root of the Spanning Tree, this object decide whether to send a new root trap.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2DevAlarmTopChange 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.3
This object determines to send a trap or not when the switch topology was changed. If the object is enabled(3), the topologyChange trap is sent by the device when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. For the same port tranition, the device doesn't send the trap if this object value is disabled or other.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2DevAlarmLinkChange 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.4
This object determines to send a trap or not when the link was changed. If the object is enabled(3), the Link Change trap is sent by the device when any of its ports link change. The device doesn't send the trap if this object value is disabled or other.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2DevAlarmPowerTable 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.5
A table that controls error state to bibi about power module.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2DevAlarmPowerEntry

swL2DevAlarmPowerEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.5.1
A list of controlling informations for power module.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwL2DevAlarmPowerEntry  

swL2DevAlarmPowerIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.5.1.1
ID of the power module.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swL2DevAlarmPowerTemperature 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.5.1.2
Controls temperature error state in power module.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2DevAlarmPowerVolt 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.5.1.3
Controls volt error state in power module.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2DevAlarmPowerCurrent 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.5.1.4
Controls current error state in power module.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2DevAlarmPowerFan 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.5.1.5
Controls fan error state in power module.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)  

swL2DevAlarmSystemFanTable 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.6
A table that controls error state to bibi about system fans.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SwL2DevAlarmSystemFanEntry

swL2DevAlarmSystemFanEntry 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.6.1
A list of controlling informations for system fans.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SwL2DevAlarmSystemFanEntry  

swL2DevAlarmSystemFanIndex 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.6.1.1
ID of the system fans.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

swL2DevAlarmSystemFanState 1.3.6.1.4.1.326.2.20.1.2.2.2.28.2.1.2.6.1.2
Controls system fan error state.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER other(1), disabled(2), enabled(3), notAvailable(4)