SONUS-SS7-SERVICES-MIB

File: SONUS-SS7-SERVICES-MIB.mib (97370 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC SONUS-COMMON-MIB
SONUS-SMI SONUS-TC

Imported symbols

Integer32 IpAddress MODULE-IDENTITY
NOTIFICATION-TYPE OBJECT-TYPE DisplayString
RowStatus TEXTUAL-CONVENTION sonusEventClass
sonusEventDescription sonusEventLevel sonusServicesMIBs
PointCode SonusName SonusPointCode
SonusPointCodeFormat

Defined Types

SonusSs7GatewayLinkSelection  
The SS7 Gateway link selection value.
TEXTUAL-CONVENTION    
  INTEGER primary(1), secondary(2), none(3), primaryAlt(4), secondaryAlt(5)  

SonusSs7GatewayEntry  
SEQUENCE    
  sonusSs7GatewayIndex Integer32
  sonusSs7GatewayState INTEGER
  sonusSs7GatewayName SonusName
  sonusSs7GatewaySocketType INTEGER
  sonusSs7GatewayActiveHost INTEGER
  sonusSs7GatewayPriHostName DisplayString
  sonusSs7GatewayPriHostIpaddr IpAddress
  sonusSs7GatewayPriHostMode INTEGER
  sonusSs7GatewayPriHostOosDelayTimer Integer32
  sonusSs7GatewaySecHostName DisplayString
  sonusSs7GatewaySecHostIpaddr IpAddress
  sonusSs7GatewaySecHostMode INTEGER
  sonusSs7GatewaySecHostOosDelayTimer Integer32
  sonusSs7GatewayRowStatus RowStatus
  sonusSs7GatewayPriAltHostIpaddr IpAddress
  sonusSs7GatewaySecAltHostIpaddr IpAddress
  sonusSs7GatewayGwType INTEGER
  sonusSs7GatewayServerTcpPort Integer32
  sonusSs7GatewayClientTcpPort Integer32
  sonusSs7GatewayPriTaliTrafficControl INTEGER
  sonusSs7GatewayPriAltTaliTrafficControl INTEGER
  sonusSs7GatewaySecTaliTrafficControl INTEGER
  sonusSs7GatewaySecAltTaliTrafficControl INTEGER
  sonusSs7GatewayTimerTaliT1 Integer32
  sonusSs7GatewayTimerTaliT2 Integer32
  sonusSs7GatewayTimerTaliT3 Integer32
  sonusSs7GatewayTimerTaliT4 Integer32
  sonusSs7GatewayTaliSs7Type INTEGER
  sonusSs7GatewaySlsBits Integer32
  sonusSs7GatewayTaliIsupNormalization INTEGER
  sonusSs7GatewayTaliPstnPresentation INTEGER
  sonusSs7GatewayTaliGroupCode DisplayString

SonusSs7GatewayStatusEntry  
SEQUENCE    
  sonusSs7GatewayStatusIndex Integer32
  sonusSs7GatewayNextHost SonusSs7GatewayLinkSelection
  sonusSs7GatewaySelectHost SonusSs7GatewayLinkSelection
  sonusSs7GatewayPriTaliConnState INTEGER
  sonusSs7GatewaySecTaliConnState INTEGER
  sonusSs7GatewayPriAltTaliConnState INTEGER
  sonusSs7GatewaySecAltTaliConnState INTEGER
  sonusSs7GatewayPriNearEndTaliVersion DisplayString
  sonusSs7GatewayPriFarEndTaliVersion DisplayString
  sonusSs7GatewayPriAltNearEndTaliVersion DisplayString
  sonusSs7GatewayPriAltFarEndTaliVersion DisplayString
  sonusSs7GatewaySecNearEndTaliVersion DisplayString
  sonusSs7GatewaySecFarEndTaliVersion DisplayString
  sonusSs7GatewaySecAltNearEndTaliVersion DisplayString
  sonusSs7GatewaySecAltFarEndTaliVersion DisplayString

SonusSs7GatewayPSStatusEntry  
SEQUENCE    
  sonusSs7GatewayPSStatusIndex Integer32
  sonusSs7GatewayPSStatusPSIndex INTEGER
  sonusSs7GatewayPSStatusPrimaryCE Integer32
  sonusSs7GatewayPSStatusActiveLink Integer32

SonusSs7GatewayLinkStatusEntry  
SEQUENCE    
  sonusSs7GatewayStatusLinkIndex Integer32
  sonusSs7GatewayStatusLinkPSIndex INTEGER
  sonusSs7GatewayStatusLinkHostIndex Integer32
  sonusSs7GatewayStatusHostName DisplayString
  sonusSs7GatewayStatusHostIpaddr IpAddress
  sonusSs7GatewayStatusHostState INTEGER
  sonusSs7GatewayStatusHostCE Integer32

SonusSs7NodeStatusEntry  
SEQUENCE    
  sonusSs7NodeStatusIndex Integer32
  sonusSs7NodeStatIsup INTEGER
  sonusSs7NodeStatMtp INTEGER

SonusSs7NodeEntry  
SEQUENCE    
  sonusSs7NodeIndex Integer32
  sonusSs7NodeState INTEGER
  sonusSs7NodeName SonusName
  sonusSs7NodePointCode PointCode
  sonusSs7NodeServices INTEGER
  sonusSs7NodeProtocol INTEGER
  sonusSs7NodeTcapSsn Integer32
  sonusSs7NodeIsupStatus INTEGER
  sonusSs7NodeTcapStatus INTEGER
  sonusSs7NodeMtpStatus INTEGER
  sonusSs7NodeGatewayAssignment DisplayString
  sonusSs7NodeNativePointCode Integer32
  sonusSs7NodeMode INTEGER
  sonusSs7NodeConnCntrl INTEGER
  sonusSs7NodeRowStatus RowStatus
  sonusSs7NodeStdPointCode SonusPointCode
  sonusSs7NodePointCodeSize Integer32
  sonusSs7NodePointCodeFormatType SonusPointCodeFormat
  sonusSs7NodeServerProtocol INTEGER
  sonusSs7NodeHandShakeInterval Integer32
  sonusSs7NodeTimerT1 Integer32
  sonusSs7NodeTimerT2 Integer32
  sonusSs7NodeTimerT3 Integer32
  sonusSs7NodeTimerT4 Integer32
  sonusSs7NodeTimerT5 Integer32
  sonusSs7NodeTimerT6 Integer32
  sonusSs7NodeTimerT7 Integer32
  sonusSs7NodeTimerT8 Integer32
  sonusSs7NodeTimerT9 Integer32
  sonusSs7NodeTimerT10 Integer32
  sonusSs7NodeTimerT11 Integer32
  sonusSs7NodeTimerT12 Integer32
  sonusSs7NodeTimerT13 Integer32
  sonusSs7NodeTimerT14 Integer32
  sonusSs7NodeTimerT15 Integer32
  sonusSs7NodeTimerT16 Integer32
  sonusSs7NodeTimerT17 Integer32
  sonusSs7NodeTimerT18 Integer32
  sonusSs7NodeTimerT19 Integer32
  sonusSs7NodeTimerT20 Integer32
  sonusSs7NodeTimerT21 Integer32
  sonusSs7NodeTimerT22 Integer32
  sonusSs7NodeTimerT23 Integer32
  sonusSs7NodeTimerT24 Integer32
  sonusSs7NodeTimerT25 Integer32
  sonusSs7NodeTimerT26 Integer32
  sonusSs7NodeTimerT27 Integer32
  sonusSs7NodeTimerT28 Integer32
  sonusSs7NodeTimerT29 Integer32
  sonusSs7NodeTimerT30 Integer32
  sonusSs7NodeTimerT31 Integer32
  sonusSs7NodeTimerT32 Integer32
  sonusSs7NodeTimerT33 Integer32
  sonusSs7NodeTimerT34 Integer32
  sonusSs7NodeTimerT35 Integer32
  sonusSs7NodeTimerT36 Integer32
  sonusSs7NodeTimerT37 Integer32
  sonusSs7NodeTimerT38 Integer32
  sonusSs7NodeTimerT39 Integer32
  sonusSs7NodeTimerT40 Integer32
  sonusSs7NodeTimerTAcc Integer32
  sonusSs7NodeTimerTCcr Integer32
  sonusSs7NodeTimerTCcrr Integer32
  sonusSs7NodeTimerTCgb Integer32
  sonusSs7NodeTimerTCra Integer32
  sonusSs7NodeTimerTCrm Integer32
  sonusSs7NodeTimerTCvt Integer32
  sonusSs7NodeTimerTExm Integer32
  sonusSs7NodeTimerTGrs Integer32
  sonusSs7NodeTimerTHga Integer32
  sonusSs7NodeTimerTScga Integer32
  sonusSs7NodeTimerTScgad Integer32
  sonusSs7NodeApplProfileName DisplayString
  sonusSs7NodeNetworkInd INTEGER
  sonusSs7NodeSlsBits Integer32
  sonusSs7NodeTimerTA Integer32
  sonusSs7NodeTimerTBlom Integer32
  sonusSs7NodeTimerTCotd Integer32
  sonusSs7NodeTimerTCotl Integer32
  sonusSs7NodeTimerTSus Integer32

SonusSs7NodeProfileEntry  
SEQUENCE    
  sonusSs7NodeProfileIndex Integer32
  sonusSs7NodeProfileName SonusName
  sonusSs7PointCodeSize Integer32
  sonusSs7PointCodeFormatType SonusPointCodeFormat
  sonusSs7ServerProtocol INTEGER
  sonusSs7HandShakeInterval Integer32
  sonusSs7TimerT1 Integer32
  sonusSs7TimerT2 Integer32
  sonusSs7TimerT3 Integer32
  sonusSs7TimerT4 Integer32
  sonusSs7TimerT5 Integer32
  sonusSs7TimerT6 Integer32
  sonusSs7TimerT7 Integer32
  sonusSs7TimerT8 Integer32
  sonusSs7TimerT9 Integer32
  sonusSs7TimerT10 Integer32
  sonusSs7TimerT11 Integer32
  sonusSs7TimerT12 Integer32
  sonusSs7TimerT13 Integer32
  sonusSs7TimerT14 Integer32
  sonusSs7TimerT15 Integer32
  sonusSs7TimerT16 Integer32
  sonusSs7TimerT17 Integer32
  sonusSs7TimerT18 Integer32
  sonusSs7TimerT19 Integer32
  sonusSs7TimerT20 Integer32
  sonusSs7TimerT21 Integer32
  sonusSs7TimerT22 Integer32
  sonusSs7TimerT23 Integer32
  sonusSs7TimerT24 Integer32
  sonusSs7TimerT25 Integer32
  sonusSs7TimerT26 Integer32
  sonusSs7TimerT27 Integer32
  sonusSs7TimerT28 Integer32
  sonusSs7TimerT29 Integer32
  sonusSs7TimerT30 Integer32
  sonusSs7TimerT31 Integer32
  sonusSs7TimerT32 Integer32
  sonusSs7TimerT33 Integer32
  sonusSs7TimerT34 Integer32
  sonusSs7TimerT35 Integer32
  sonusSs7TimerT36 Integer32
  sonusSs7TimerT37 Integer32
  sonusSs7TimerT38 Integer32
  sonusSs7TimerT39 Integer32
  sonusSs7TimerT40 Integer32
  sonusSs7TimerTAcc Integer32
  sonusSs7TimerTCcr Integer32
  sonusSs7TimerTCcrr Integer32
  sonusSs7TimerTCgb Integer32
  sonusSs7TimerTCra Integer32
  sonusSs7TimerTCrm Integer32
  sonusSs7TimerTCvt Integer32
  sonusSs7TimerTExm Integer32
  sonusSs7TimerTGrs Integer32
  sonusSs7TimerTHga Integer32
  sonusSs7TimerTScga Integer32
  sonusSs7TimerTScgad Integer32
  sonusSs7NodeProfileState INTEGER
  sonusSs7NodeProfileRowStatus RowStatus
  sonusSs7NodeProfileNetworkInd INTEGER
  sonusSs7SlsBits Integer32
  sonusSs7TimerTA Integer32
  sonusSs7TimerTBlom Integer32
  sonusSs7TimerTCotd Integer32
  sonusSs7TimerTCotl Integer32
  sonusSs7TimerTSus Integer32

Defined Values

sonusSs7ServicesMIB 1.3.6.1.4.1.2879.2.5.3
The MIB Module for SS7 Gateway and SS7 Node Configuration.
MODULE-IDENTITY    

sonusSs7ServicesMIBObjects 1.3.6.1.4.1.2879.2.5.3.1
OBJECT IDENTIFIER    

sonusSs7Gateway 1.3.6.1.4.1.2879.2.5.3.1.1
OBJECT IDENTIFIER    

sonusSs7GatewayNextIndex 1.3.6.1.4.1.2879.2.5.3.1.1.1
The next valid index to use when creating an entry in the sonusSs7GatewayTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sonusSs7GatewayTable 1.3.6.1.4.1.2879.2.5.3.1.1.2
This table specifies the SS7 Gateway list for the GSX9000 node.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonusSs7GatewayEntry

sonusSs7GatewayEntry 1.3.6.1.4.1.2879.2.5.3.1.1.2.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SonusSs7GatewayEntry  

sonusSs7GatewayIndex 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.1
Identifies the target SS7 Gateway entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sonusSs7GatewayState 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.2
The administrative state of this SS7 Gateway entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

sonusSs7GatewayName 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.3
The name of this SS7 Gateway instance.
Status: current Access: read-write
OBJECT-TYPE    
  SonusName  

sonusSs7GatewaySocketType 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.4
Indicates the type of socket interface used by the GSX9000 node for connections to the SS7 Gateway platform.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER tcp(1)  

sonusSs7GatewayActiveHost 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.5
This status value has been replaced by sonusSs7GatewayNextHost and sonusSs7GatewaySelectHost.
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), none(3)  

sonusSs7GatewayPriHostName 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.6
The host name of the primary link to the SS7 Gateway platform.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..39)  

sonusSs7GatewayPriHostIpaddr 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.7
Specifies the IP Address of the primary link to the SS7 Gateway platform.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sonusSs7GatewayPriHostMode 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.8
Specifies the service mode of the primary link to the SS7 Gateway platform.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER inService(1), outOfService(2)  

sonusSs7GatewayPriHostOosDelayTimer 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.9
This element is used to delay the action of taking the primary host link out of service for a specified number of minutes.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1440  

sonusSs7GatewaySecHostName 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.10
The host name of the secondary link to the SS7 Gateway platform.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..39)  

sonusSs7GatewaySecHostIpaddr 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.11
Specifies the IP Address of the secondary link to the SS7 Gateway platform.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sonusSs7GatewaySecHostMode 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.12
Specifies the service mode of the secondary link to the SS7 Gateway platform.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER inService(1), outOfService(2)  

sonusSs7GatewaySecHostOosDelayTimer 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.13
This element is used to delay the action of taking the secondary host link out of service for a specified number of minutes.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1440  

sonusSs7GatewayRowStatus 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.14
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

sonusSs7GatewayPriAltHostIpaddr 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.15
Specifies the alternate IP Address of the primary link to the SS7 Gateway platform.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sonusSs7GatewaySecAltHostIpaddr 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.16
Specifies the alternate IP Address of the secondary link to the SS7 Gateway platform.
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sonusSs7GatewayGwType 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.17
Gateway type is identified by the gateway protocol it uses
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER tali(1), dgms(2)  

sonusSs7GatewayServerTcpPort 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.18
TCP port for the server of TALI connection
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1024..65535  

sonusSs7GatewayClientTcpPort 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.19
TCP port for the client of TALI connection
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1024..65535  

sonusSs7GatewayPriTaliTrafficControl 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.20
Control the ss7 traffic on the primary TALI connection
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allow(1), prohibit(2)  

sonusSs7GatewayPriAltTaliTrafficControl 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.21
Control the ss7 traffic on the primary TALI connection
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allow(1), prohibit(2)  

sonusSs7GatewaySecTaliTrafficControl 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.22
Control the ss7 traffic on the secondary TALI connection
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allow(1), prohibit(2)  

sonusSs7GatewaySecAltTaliTrafficControl 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.23
Control the ss7 traffic on the secondary TALI connection
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER allow(1), prohibit(2)  

sonusSs7GatewayTimerTaliT1 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.24
Send a TALI-TEST upon the expiry of T1 in millisecond.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 100..60000  

sonusSs7GatewayTimerTaliT2 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.25
Guard timer in millisecond for the return of TALI-ALLO or TALI-PROH in response to a TALI-TEST sent earlier.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 100..60000  

sonusSs7GatewayTimerTaliT3 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.26
T3 in millisecond reprsents how long the near end can continue to process received messages after sending TALI-PROH.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 100..60000  

sonusSs7GatewayTimerTaliT4 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.27
Send a TALI-MONI upon the expiry of T4 in millisecond.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 100..60000  

sonusSs7GatewayTaliSs7Type 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.28
SS7 protocol types used over TALI
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ansi(1), ituIntl(2), ituNatl(3)  

sonusSs7GatewaySlsBits 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.29
The number of SLS bits to use
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..8  

sonusSs7GatewayTaliIsupNormalization 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.30
ISUP message format over TALI -- normalized or raw
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER norm(1), raw(2)  

sonusSs7GatewayTaliPstnPresentation 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.31
ISUP types over TALI
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER q767(1), etsiIsup(2), ukIsup(3), grIsup(4)  

sonusSs7GatewayTaliGroupCode 1.3.6.1.4.1.2879.2.5.3.1.1.2.1.32
Group Code in ASCII
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(2)  

sonusSs7GatewayStatusTable 1.3.6.1.4.1.2879.2.5.3.1.1.3
Status Table of the SS7 Gateway for the GSX9000 node.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonusSs7GatewayStatusEntry

sonusSs7GatewayStatusEntry 1.3.6.1.4.1.2879.2.5.3.1.1.3.1
List of SS7 Gateway status elements.
Status: current Access: not-accessible
OBJECT-TYPE    
  SonusSs7GatewayStatusEntry  

sonusSs7GatewayStatusIndex 1.3.6.1.4.1.2879.2.5.3.1.1.3.1.1
Identifies the SS7 Gateway status entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sonusSs7GatewayNextHost 1.3.6.1.4.1.2879.2.5.3.1.1.3.1.2
Indicates which host link connection to the SS7 Gateway is next to be selected. If there is none, then this element is set to none.
Status: current Access: read-only
OBJECT-TYPE    
  SonusSs7GatewayLinkSelection  

sonusSs7GatewaySelectHost 1.3.6.1.4.1.2879.2.5.3.1.1.3.1.3
Indicates which host link connection to the SS7 Gateway is selected to be tried. If there is none, then this element is set to none.
Status: current Access: read-only
OBJECT-TYPE    
  SonusSs7GatewayLinkSelection  

sonusSs7GatewayPriTaliConnState 1.3.6.1.4.1.2879.2.5.3.1.1.3.1.4
TALI state of the primary connection for this SS7 gateway.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER oos(1), connecting(2), nepFep(3), nepFea(4), neaFep(5), neaFea(6)  

sonusSs7GatewaySecTaliConnState 1.3.6.1.4.1.2879.2.5.3.1.1.3.1.5
TALI state of the secondary connection for this SS7 gateway.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER oos(1), connecting(2), nepFep(3), nepFea(4), neaFep(5), neaFea(6)  

sonusSs7GatewayPriAltTaliConnState 1.3.6.1.4.1.2879.2.5.3.1.1.3.1.6
TALI state of the primary alt connection for this SS7 gateway.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER oos(1), connecting(2), nepFep(3), nepFea(4), neaFep(5), neaFea(6)  

sonusSs7GatewaySecAltTaliConnState 1.3.6.1.4.1.2879.2.5.3.1.1.3.1.7
TALI state of the secondary alt connection for this SS7 gateway.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER oos(1), connecting(2), nepFep(3), nepFea(4), neaFep(5), neaFea(6)  

sonusSs7GatewayPriNearEndTaliVersion 1.3.6.1.4.1.2879.2.5.3.1.1.3.1.8
TALI protocol version at the near end of the pri conncection
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(7)  

sonusSs7GatewayPriFarEndTaliVersion 1.3.6.1.4.1.2879.2.5.3.1.1.3.1.9
TALI protocol version at the far end of the pri connection
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(7)  

sonusSs7GatewayPriAltNearEndTaliVersion 1.3.6.1.4.1.2879.2.5.3.1.1.3.1.10
TALI protocol version at the near end of the pri-alt conn.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(7)  

sonusSs7GatewayPriAltFarEndTaliVersion 1.3.6.1.4.1.2879.2.5.3.1.1.3.1.11
TALI protocol version at the far end of the pri-alt connection
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(7)  

sonusSs7GatewaySecNearEndTaliVersion 1.3.6.1.4.1.2879.2.5.3.1.1.3.1.12
TALI protocol version at the near end of the sec conncection
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(7)  

sonusSs7GatewaySecFarEndTaliVersion 1.3.6.1.4.1.2879.2.5.3.1.1.3.1.13
TALI protocol version at the far end of the sec connection
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(7)  

sonusSs7GatewaySecAltNearEndTaliVersion 1.3.6.1.4.1.2879.2.5.3.1.1.3.1.14
TALI protocol version at the near end of the sec-alt conn.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(7)  

sonusSs7GatewaySecAltFarEndTaliVersion 1.3.6.1.4.1.2879.2.5.3.1.1.3.1.15
TALI protocol version at the far end of the sec-alt connection
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(7)  

sonusSs7GatewayPSStatusTable 1.3.6.1.4.1.2879.2.5.3.1.1.4
Status Table of the SS7 Gateway of a PRIMARY or SECONDARY for the GSX9000 node.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonusSs7GatewayPSStatusEntry

sonusSs7GatewayPSStatusEntry 1.3.6.1.4.1.2879.2.5.3.1.1.4.1
List of SS7 Gateway status elements.
Status: current Access: not-accessible
OBJECT-TYPE    
  SonusSs7GatewayPSStatusEntry  

sonusSs7GatewayPSStatusIndex 1.3.6.1.4.1.2879.2.5.3.1.1.4.1.1
Identifies the SS7 Gateway status entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sonusSs7GatewayPSStatusPSIndex 1.3.6.1.4.1.2879.2.5.3.1.1.4.1.2
Identifies the SS7 Gateway link status entry.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER primary(0), secondary(1), primaryAlt(2), secondaryAlt(3)  

sonusSs7GatewayPSStatusPrimaryCE 1.3.6.1.4.1.2879.2.5.3.1.1.4.1.3
Identifies the link Primary CE value.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  


sonusSs7GatewayLinkStatusTable 1.3.6.1.4.1.2879.2.5.3.1.1.5
Link Status Table of a SS7 Gateway for the GSX9000 node.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonusSs7GatewayLinkStatusEntry

sonusSs7GatewayLinkStatusEntry 1.3.6.1.4.1.2879.2.5.3.1.1.5.1
List of SS7 Gateway Link Status elements.
Status: current Access: not-accessible
OBJECT-TYPE    
  SonusSs7GatewayLinkStatusEntry  

sonusSs7GatewayStatusLinkIndex 1.3.6.1.4.1.2879.2.5.3.1.1.5.1.1
Identifies the SS7 Gateway status link entry gateway index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sonusSs7GatewayStatusLinkPSIndex 1.3.6.1.4.1.2879.2.5.3.1.1.5.1.2
Identifies the SS7 Gateway status link entry primary or secondary index.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER primary(1), secondary(2), primaryAlt(3), secondaryAlt(4)  

sonusSs7GatewayStatusLinkHostIndex 1.3.6.1.4.1.2879.2.5.3.1.1.5.1.3
Identifies the SS7 Gateway host status link entry index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sonusSs7GatewayStatusHostName 1.3.6.1.4.1.2879.2.5.3.1.1.5.1.4
The host name of the Link link to the SS7 Gateway platform.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..39)  

sonusSs7GatewayStatusHostIpaddr 1.3.6.1.4.1.2879.2.5.3.1.1.5.1.5
Specifies the IP Address of the link to the SS7 Gateway platform.
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

sonusSs7GatewayStatusHostState 1.3.6.1.4.1.2879.2.5.3.1.1.5.1.6
The state of host link to the SS7 Gateway platform.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER empty(1), init(2), available(3), broken(4)  

sonusSs7GatewayStatusHostCE 1.3.6.1.4.1.2879.2.5.3.1.1.5.1.7
The CE of host link to the SS7 Gateway platform.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sonusSs7NodeStatusTable 1.3.6.1.4.1.2879.2.5.3.1.1.6
Status Table of the SS7 Node for the GSX9000 node.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonusSs7NodeStatusEntry

sonusSs7NodeStatusEntry 1.3.6.1.4.1.2879.2.5.3.1.1.6.1
List of SS7 Node status elements.
Status: current Access: not-accessible
OBJECT-TYPE    
  SonusSs7NodeStatusEntry  

sonusSs7NodeStatusIndex 1.3.6.1.4.1.2879.2.5.3.1.1.6.1.1
Identifies the SS7 Node status entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sonusSs7NodeStatIsup 1.3.6.1.4.1.2879.2.5.3.1.1.6.1.2
Specifies the operating status of the ISUP service within this SS7 Node.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER offline(1), active(2), initializing(3), failed(4), disabled(5), congested(6)  

sonusSs7NodeStatMtp 1.3.6.1.4.1.2879.2.5.3.1.1.6.1.3
Specifies the current MTP status for this SS7 Node.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER paused(1), resumed(2)  

sonusSs7Node 1.3.6.1.4.1.2879.2.5.3.1.2
OBJECT IDENTIFIER    

sonusSs7NodeNextIndex 1.3.6.1.4.1.2879.2.5.3.1.2.1
The next valid index to use when creating an entry in the sonusSs7NodeTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sonusSs7NodeTable 1.3.6.1.4.1.2879.2.5.3.1.2.2
This table specifies the SS7 Node list for the GSX9000 node.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonusSs7NodeEntry

sonusSs7NodeEntry 1.3.6.1.4.1.2879.2.5.3.1.2.2.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SonusSs7NodeEntry  

sonusSs7NodeIndex 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.1
Identifies the target SS7 Node entry.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sonusSs7NodeState 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.2
The administrative state of this SS7 Node entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

sonusSs7NodeName 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.3
The name of this SS7 Node instance.
Status: current Access: read-write
OBJECT-TYPE    
  SonusName  

sonusSs7NodePointCode 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.4
The SS7 point code assigned to this SS7 Node entry.
Status: current Access: read-write
OBJECT-TYPE    
  PointCode  

sonusSs7NodeServices 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.5
The type of SS7 services (ISUP, TCAP, or both) supported by this SS7 Node entry. As of GSX release 3.02.00, isupOnly is now the only vaild option for this entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER isupOnly(1), tcapOnly(2), isupAndTcap(3)  

sonusSs7NodeProtocol 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.6
The SS7 protocol type supported by this SS7 Node entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER ansi(1), itu(2), etsi(3), japan(4)  

sonusSs7NodeTcapSsn 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.7
If Tcap is supported by this SS7 Node, specifies the Sub System Number for this node entry. This object is obsoleted as of GSX release 3.02.00.
Status: obsolete Access: read-write
OBJECT-TYPE    
  Integer32  

sonusSs7NodeIsupStatus 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.8
This status value has been replaced by sonusSs7NodeStatIsup
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER offline(1), active(2), initializing(3), failed(4), disabled(5), congested(6)  

sonusSs7NodeTcapStatus 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.9
Specifies the operating status of the TCAP service within this SS7 Node. This object is obsoleted as of GSX release 3.02.00.
Status: obsolete Access: read-only
OBJECT-TYPE    
  INTEGER offline(1), active(2), initializing(3), failed(4), disabled(5), congested(6)  

sonusSs7NodeMtpStatus 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.10
This status value has been replaced by sonusSs7NodeStatMtp
Status: deprecated Access: read-only
OBJECT-TYPE    
  INTEGER paused(1), resumed(2)  

sonusSs7NodeGatewayAssignment 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.11
The name of the SS7 Gateway to which this SS7 Node is assigned.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(1..23)  

sonusSs7NodeNativePointCode 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.12
The native point code of the SS7 node. e.g. For ITU the point code is in 3 bit 8 bit 3 bit format adding up to 14 bits whereas ANSI uses a 8bit 8bit 8bit format adding up to 24 bits.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sonusSs7NodeMode 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.13
Specifies the service mode for this SS7 Node.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER inService(1), outOfService(2)  

sonusSs7NodeConnCntrl 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.14
Specifies when the Node will establish an ISUP connection with the SS7 Gateway. This parameter is used to minimize unnecessary connections to the SS7 Gateway for ISUP services, allowing the GSX to only establish the ISUP connections that are required by ISUP circuits on a particular shelf. When set to always, the ISUP service connection will be established when the node is enabled. When set to asNeeded, the ISUP service connection will be established only if there are ISUP circuits assigned to this node. This parameter only applies to ISUP service registration.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER always(1), asNeeded(2)  

sonusSs7NodeRowStatus 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.15
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

sonusSs7NodeStdPointCode 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.16
Octet string of the point code. This gives the actual representation the user entered.
Status: current Access: read-write
OBJECT-TYPE    
  SonusPointCode  

sonusSs7NodePointCodeSize 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.17
Indicates the total number of bits in the point code.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..32  

sonusSs7NodePointCodeFormatType 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.18
The Point Code format type being defined.
Status: current Access: read-write
OBJECT-TYPE    
  SonusPointCodeFormat  

sonusSs7NodeServerProtocol 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.19
The interface used between the SS7 gateway and the SS7 client on the GSX9000
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dgmsProp(1), dgmsRaw(2), tekTali(3)  

sonusSs7NodeHandShakeInterval 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.20
HandShake interval between the client and the server in seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..255  

sonusSs7NodeTimerT1 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.21
The Timer T1 could be changed from its default using this entry. The valid ranges are 4 - 15 seconds for ANSI and 15 - 60 Seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..60  

sonusSs7NodeTimerT2 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.22
The Timer T2 could be changed from its default using this entry. The valid value for ITU is 3 Minutes. This timer has no relevence in the ANSI network.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..255  

sonusSs7NodeTimerT3 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.23
The T3 timer is started on receipt of an Overload message in the ITU network. This has no relevence in the ANSI network. The valid ITU recommended value is 120 Seconds
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..255  

sonusSs7NodeTimerT4 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.24
The Timer T4 could be changed from its default using this entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 300..900  

sonusSs7NodeTimerT5 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.25
The T5 Timer is started when the release message is sent. The valid values as per the specifications are 60 seconds for the ANSI and 300 to 900 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..900  

sonusSs7NodeTimerT6 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.26
The timer T6 is started when the suspend message is received. The valid range for this timer is 1 to 120 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..120  

sonusSs7NodeTimerT7 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.27
The Timer T7 could be changed from its default using this entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 20..30  

sonusSs7NodeTimerT8 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.28
The T8 timer is timer to be started with continuity check has been indicated in the IAM. The valid range is 10 to 15 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10..15  

sonusSs7NodeTimerT9 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.29
The Timer T9 started when outgoing international exchange recieves an ACM. The valid range is 120 to 240 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 120..240  

sonusSs7NodeTimerT10 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.30
The Timer T10 is started when the last digit is recived in interworking situations. This timer has no relevence to ANSI.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..6  

sonusSs7NodeTimerT11 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.31
The Timer T11 is started when the latest address message is received in interworking situations. The valid range is 15 to 20 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 15..20  

sonusSs7NodeTimerT12 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.32
The Timer T12 is started when a blocking message is sent. The valid ranges are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..60  

sonusSs7NodeTimerT13 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.33
The Timer T13 is started when the initial blocking messge is sent. The valid value for ANSI is 60 seconds and for ITU is between 300 and 900 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..900  

sonusSs7NodeTimerT14 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.34
The Timer T14 is started when an unblocking message is sent. The valid values are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..60  

sonusSs7NodeTimerT15 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.35
The Timer T15 is started when the initial unblocking message is sent. The valid values are 60 seconds for ANSI and 300 to 900 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..900  

sonusSs7NodeTimerT16 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.36
The Timer T16 is started when the reset circuit is started which was not due to expiry of T5. The valid ranges are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..60  

sonusSs7NodeTimerT17 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.37
The Timer T17 is started when initial reset message is sent. The valid values are 60 seconds for ANSI and 300 to 900 for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..900  

sonusSs7NodeTimerT18 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.38
The Timer T18 is started when circuit group blocking message is sent. The valid values are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..60  

sonusSs7NodeTimerT19 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.39
The Timer T19 is started when initial group blocking message is sent. The valid values are 60 seconds for ANSI and 300 to 900 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..900  

sonusSs7NodeTimerT20 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.40
The Timer T20 is started when group unblocking message is sent. The valid ranges are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..60  

sonusSs7NodeTimerT21 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.41
The Timer T21 is started when initial group blocking message is sent. The valid values are 60 seconds for ANSI and 300 to 900 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..900  

sonusSs7NodeTimerT22 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.42
The Timer T22 is started when circuit group reset message is sent. The valid values are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..60  

sonusSs7NodeTimerT23 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.43
The Timer T23 is started when initial group reset message is sent. The valid values are 60 seconds for the ANSI and 300 to 900 seconds for the ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..900  

sonusSs7NodeTimerT24 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.44
The Timer T24 is started when check tone is sent. The value is less than 2 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..2  

sonusSs7NodeTimerT25 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.45
The Timer T25 is started when initial continuity check failure is detected. The range is 1 to 10 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..10  

sonusSs7NodeTimerT26 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.46
The Timer T26 is started when a second or subsequent continuity failure is detected. The valid value are 60 to 180 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..180  

sonusSs7NodeTimerT27 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.47
The Timer T27 is started when a continuity fail message is recieved. The valid values are more than 180 seconds for ANSI and 240 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 180..36000  

sonusSs7NodeTimerT28 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.48
The Timer T28 is started when Circuit Query Message is sent. The valid value is 10 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 5..12  

sonusSs7NodeTimerT29 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.49
The Timer T29 is started when Congestion indication is received when T29 is not running. The valid range is 300 to 600 milli second. This timer has no relevence for ANSI.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 300..600  

sonusSs7NodeTimerT30 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.50
The Timer T30 is stared when congestion indication is recieved when T29 is not running. The valid range is 5 to 10 seconds for the ITU. This timer has no relevence under ANSI.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 5..10  

sonusSs7NodeTimerT31 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.51
The Timer T31 is started on release of ISUP signalling connection based on CO SCCP. The value should be set to greater than 360 seconds
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 360..65520  

sonusSs7NodeTimerT32 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.52
The Timer T32 is started when the first end-to-end message is recived. Under ANSI this timer is started after the response to such a message is sent. The valid values are 3 to 5 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 3..5  

sonusSs7NodeTimerT33 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.53
The Timer T33 is started when Information Request Message is sent. The valid range is 12 to 15 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 12..15  

sonusSs7NodeTimerT34 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.54
The Timer T34 is started when Loop Back Acknowledgement is sent under ANSI. The Timer T34 is started when segmentation is received for IAM, ACM, CPG, ANM or CON under ITU. The valid range for ANSI is 10 to 15 seconds. The valid range for ITU is 2 to 4 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..15  

sonusSs7NodeTimerT35 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.55
The Timer T35 is started when the last digit recieved is not an ST digit or the fixed number of digits have been recieved. This procedure is only valid for overlap hence ITU. This timer has no relevence in ANSI.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 15..20  

sonusSs7NodeTimerT36 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.56
The Timer T36 is started when IAM is recived with a segmentation indication for ANSI. This timer is started when transit or incoming international exchange recieves Continuity check request message. The valid range for ANSI is 2 to 4 seconds and 10 to 15 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..15  

sonusSs7NodeTimerT37 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.57
The Timer T37 is started when User Part Availability test is started under ANSI. This timer is started when a request for and Echo control device is sent to another exchange under ITU. The valid value for ANSI is 30 seconds and for ITU is 2 to 4 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..30  

sonusSs7NodeTimerT38 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.58
The Timer T38 is started when a suspend message is sent to the preceding switch. This timer is only relevent under ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10..60  

sonusSs7NodeTimerT39 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.59
The Timer T39 is started when MCID request is sent. It is only relevent in the ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

sonusSs7NodeTimerT40 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.60
The Timer T40 could be changed from its default using this entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

sonusSs7NodeTimerTAcc 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.61
Automatic Congestion Control Timer as per ANSI T1.113.4 - 1995. The value of the timer is 5 Seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 3..8  

sonusSs7NodeTimerTCcr 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.62
Continuity Check Request Timer. The value As per ANSI T1.113.4 - 1995 is 2 Seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..3  

sonusSs7NodeTimerTCcrr 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.63
Continuity Check Failed Recived. The value as per ANSI T1.113.4 - 1995 is 20 Seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 16..31  

sonusSs7NodeTimerTCgb 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.64
Timer started on recipt of a Circuit Group Block Message. The value as per ANSI T1.113.4 - 1995 is 5 Seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 3..8  

sonusSs7NodeTimerTCra 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.65
Timer started when Circuit Reservation Acknowledgment is sent. The time value as per ANSI T1.113.4 - 1995 is 20 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 16..31  

sonusSs7NodeTimerTCrm 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.66
This timer is started when the circuit reservation message is sent. The value as per ANSI T1.113.4 - 1995 is 3 - 4 Seconds. The default is set to 4 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 3..4  

sonusSs7NodeTimerTCvt 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.67
The Timer T CVT is started when the Circuit Validation Test message is sent. This message is only valid for ANSI.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 5..12  

sonusSs7NodeTimerTExm 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.68
The Timer Exm,d is started when IAM is sent to the succeeding network. This timer has no relevence in the ITU. This timer is in milliseconds
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

sonusSs7NodeTimerTGrs 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.69
This timer is started when a circuit group reset message is received. This timer is only relevent in the ANSI network.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 3..8  

sonusSs7NodeTimerTHga 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.70
This timer is started on recognition of carrier loss. It is only relevent in ANSI network. The valid range is 0 to 300 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..300  

sonusSs7NodeTimerTScga 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.71
This timer is started when initial demand continuity check fails in the SCGA group. The valid range for this timer is 0 to 120 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..120  

sonusSs7NodeTimerTScgad 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.72
This timer is started failure of demand continuity check in the SCGA group.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 5..120  

sonusSs7NodeApplProfileName 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.73
The SS7 Node Profile to be applied to the node. The values here are a snap shot only and might have changed since they were set.
Status: current Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..23)  

sonusSs7NodeNetworkInd 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.74
The setting of the Network Indicator used for this SS7 Node entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER intl0(1), intl1(2), natl0(3), natl1(4)  

sonusSs7NodeSlsBits 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.75
The number of SLS bits to use
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..8  

sonusSs7NodeTimerTA 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.76
The Bellcore specific timer TA is the guard timer on outgoing SS7 circuit before idling. The value of this timer is 0 to 1000 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1000  

sonusSs7NodeTimerTBlom 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.77
The Bellcore specific timer TBlom is started when blocking a circuit due to a BLO, and after any call is released; used to notify maintenance.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 240..360  

sonusSs7NodeTimerTCotd 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.78
The Bellcore specific timer TCOTd is started when sending IAM requesting continuity check. The value of this timer is in milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..500  

sonusSs7NodeTimerTCotl 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.79
The Bellcore specific timer TCOTl is started when receiving second COT coded failed, awaiting receipt of CCR.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 240..300  

sonusSs7NodeTimerTSus 1.3.6.1.4.1.2879.2.5.3.1.2.2.1.80
The Bellcore specific timer TSUS is started when a SUS message is sent by the terminating switch, awaiting called party off-hook or REL.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 14..16  

sonusSs7NodeProfile 1.3.6.1.4.1.2879.2.5.3.1.3
OBJECT IDENTIFIER    

sonusSs7NodeProfileNextIndex 1.3.6.1.4.1.2879.2.5.3.1.3.1
The next valid index to use when creating an entry in the sonusSs7NodeProfileTable.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sonusSs7NodeProfileTable 1.3.6.1.4.1.2879.2.5.3.1.3.2
This table specifies the SS7 Node Profile list for the GSX9000 node.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SonusSs7NodeProfileEntry

sonusSs7NodeProfileEntry 1.3.6.1.4.1.2879.2.5.3.1.3.2.1
Tok_String
Status: current Access: not-accessible
OBJECT-TYPE    
  SonusSs7NodeProfileEntry  

sonusSs7NodeProfileIndex 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.1
Identifies the SS7 Node Profile entry
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sonusSs7NodeProfileName 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.2
The name of the Node Profile
Status: current Access: read-write
OBJECT-TYPE    
  SonusName  

sonusSs7PointCodeSize 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.3
Indicates the total number of bits in the point code.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..32  

sonusSs7PointCodeFormatType 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.4
The Point Code format type being defined.
Status: current Access: read-write
OBJECT-TYPE    
  SonusPointCodeFormat  

sonusSs7ServerProtocol 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.5
The interface used between the SS7 gateway and the SS7 client on the GSX9000
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dgmsProp(1), dgmsRaw(2), tekTali(3)  

sonusSs7HandShakeInterval 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.6
HandShake interval between the client and the server in seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..255  

sonusSs7TimerT1 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.7
The Timer T1 could be changed from its default using this entry. The valid ranges are 4 - 15 seconds for ANSI and 15 - 60 Seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..60  

sonusSs7TimerT2 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.8
The Timer T2 could be changed from its default using this entry. The valid value for ITU is 3 Minutes. This timer has no relevence in the ANSI network.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..255  

sonusSs7TimerT3 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.9
The T3 timer is started on receipt of an Overload message in the ITU network. This has no relevence in the ANSI network. The valid ITU recommended value is 120 Seconds
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..255  

sonusSs7TimerT4 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.10
The Timer T4 could be changed from its default using this entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 300..900  

sonusSs7TimerT5 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.11
The T5 Timer is started when the release message is sent. The valid values as per the specifications are 60 seconds for the ANSI and 300 to 900 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..900  

sonusSs7TimerT6 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.12
The timer T6 is started when the suspend message is received. The valid range for this timer is 10 to 32 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10..32  

sonusSs7TimerT7 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.13
The Timer T7 could be changed from its default using this entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 20..30  

sonusSs7TimerT8 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.14
The T8 timer is timer to be started with continuity check has been indicated in the IAM. The valid range is 10 to 15 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10..15  

sonusSs7TimerT9 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.15
The Timer T9 started when outgoing international exchange recieves an ACM. The valid range is 120 to 240 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 120..240  

sonusSs7TimerT10 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.16
The Timer T10 is started when the last digit is recived in interworking situations. This timer has no relevence to ANSI.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 240..360  

sonusSs7TimerT11 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.17
The Timer T11 is started when the latest address message is received in interworking situations. The valid range is 15 to 20 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 15..20  

sonusSs7TimerT12 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.18
The Timer T12 is started when a blocking message is sent. The valid ranges are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..60  

sonusSs7TimerT13 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.19
The Timer T13 is started when the initial blocking messge is sent. The valid value for ANSI is 60 seconds and for ITU is between 300 and 900 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..900  

sonusSs7TimerT14 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.20
The Timer T14 is started when an unblocking message is sent. The valid values are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..60  

sonusSs7TimerT15 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.21
The Timer T15 is started when the initial unblocking message is sent. The valid values are 60 seconds for ANSI and 300 to 900 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..900  

sonusSs7TimerT16 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.22
The Timer T16 is started when the reset circuit is started which was not due to expiry of T5. The valid ranges are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..60  

sonusSs7TimerT17 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.23
The Timer T17 is started when initial reset message is sent. The valid values are 60 seconds for ANSI and 300 to 900 for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..900  

sonusSs7TimerT18 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.24
The Timer T18 is started when circuit group blocking message is sent. The valid values are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..60  

sonusSs7TimerT19 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.25
The Timer T19 is started when initial group blocking message is sent. The valid values are 60 seconds for ANSI and 300 to 900 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..900  

sonusSs7TimerT20 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.26
The Timer T20 is started when group unblocking message is sent. The valid ranges are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..60  

sonusSs7TimerT21 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.27
The Timer T21 is started when initial group blocking message is sent. The valid values are 60 seconds for ANSI and 300 to 900 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..900  

sonusSs7TimerT22 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.28
The Timer T22 is started when circuit group reset message is sent. The valid values are 4 to 15 seconds for ANSI and 15 to 60 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..60  

sonusSs7TimerT23 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.29
The Timer T23 is started when initial group reset message is sent. The valid values are 60 seconds for the ANSI and 300 to 900 seconds for the ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..900  

sonusSs7TimerT24 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.30
The Timer T24 is started when check tone is sent. The value is less than 2 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..2  

sonusSs7TimerT25 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.31
The Timer T25 is started when initial continuity check failure is detected. The range is 1 to 10 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..10  

sonusSs7TimerT26 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.32
The Timer T26 is started when a second or subsequent continuity failure is detected. The valid value are 60 to 180 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 60..180  

sonusSs7TimerT27 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.33
The Timer T27 is started when a continuity fail message is recieved. The valid values are more than 180 seconds for ANSI and 240 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 180..36000  

sonusSs7TimerT28 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.34
The Timer T28 is started when Circuit Query Message is sent. The valid value is 10 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 5..12  

sonusSs7TimerT29 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.35
The Timer T29 is started when Congestion indication is received when T29 is not running. The valid range is 300 to 600 milli second. This timer has no relevence for ANSI.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 300..600  

sonusSs7TimerT30 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.36
The Timer T30 is stared when congestion indication is recieved when T29 is not running. The valid range is 5 to 10 seconds for the ITU. This timer has no relevence under ANSI.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 5..10  

sonusSs7TimerT31 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.37
The Timer T31 is started on release of ISUP signalling connection based on CO SCCP. The value should be set to greater than 360 seconds
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 360..65520  

sonusSs7TimerT32 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.38
The Timer T32 is started when the first end-to-end message is recived. Under ANSI this timer is started after the response to such a message is sent. The valid values are 3 to 5 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 3..5  

sonusSs7TimerT33 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.39
The Timer T33 is started when Information Request Message is sent. The valid range is 12 to 15 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 12..15  

sonusSs7TimerT34 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.40
The Timer T34 is started when Loop Back Acknowledgement is sent under ANSI. The Timer T34 is started when segmentation is received for IAM, ACM, CPG, ANM or CON under ITU. The valid range for ANSI is 10 to 15 seconds. The valid range for ITU is 2 to 4 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..15  

sonusSs7TimerT35 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.41
The Timer T35 is started when the last digit recieved is not an ST digit or the fixed number of digits have been recieved. This procedure is only valid for overlap hence ITU. This timer has no relevence in ANSI.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 15..20  

sonusSs7TimerT36 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.42
The Timer T36 is started when IAM is recived with a segmentation indication for ANSI. This timer is started when transit or incoming international exchange recieves Continuity check request message. The valid range for ANSI is 2 to 4 seconds and 10 to 15 seconds for ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..15  

sonusSs7TimerT37 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.43
The Timer T37 is started when User Part Availability test is started under ANSI. This timer is started when a request for and Echo control device is sent to another exchange under ITU. The valid value for ANSI is 30 seconds and for ITU is 2 to 4 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..30  

sonusSs7TimerT38 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.44
The Timer T38 is started when a suspend message is sent to the preceding switch. This timer is only relevent under ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 10..60  

sonusSs7TimerT39 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.45
The Timer T39 is started when MCID request is sent. It is only relevent in the ITU.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

sonusSs7TimerT40 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.46
The Timer T40 could be changed from its default using this entry.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

sonusSs7TimerTAcc 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.47
Automatic Congestion Control Timer as per ANSI T1.113.4 - 1995. The value of the timer is 5 Seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 3..8  

sonusSs7TimerTCcr 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.48
Continuity Check Request Timer. The value As per ANSI T1.113.4 - 1995 is 2 Seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..3  

sonusSs7TimerTCcrr 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.49
Continuity Check Failed Recived. The value as per ANSI T1.113.4 - 1995 is 20 Seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 16..31  

sonusSs7TimerTCgb 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.50
Timer started on recipt of a Circuit Group Block Message. The value as per ANSI T1.113.4 - 1995 is 5 Seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 3..8  

sonusSs7TimerTCra 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.51
Timer started when Circuit Reservation Acknowledgment is sent. The time value as per ANSI T1.113.4 - 1995 is 20 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 16..31  

sonusSs7TimerTCrm 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.52
This timer is started when the circuit reservation message is sent. The value as per ANSI T1.113.4 - 1995 is 3 - 4 Seconds. The default is set to 4 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 3..4  

sonusSs7TimerTCvt 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.53
The Timer T CVT is started when the Circuit Validation Test message is sent. This message is only valid for ANSI.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 5..12  

sonusSs7TimerTExm 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.54
The Timer Exm,d is started when IAM is sent to the succeeding network. This timer has no relevence in the ITU. This timer is in milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

sonusSs7TimerTGrs 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.55
This timer is started when a circuit group reset message is received. This timer is only relevent in the ANSI network.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 3..8  

sonusSs7TimerTHga 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.56
This timer is started on recognition of carrier loss. It is only relevent in ANSI network. The valid range is 0 to 300 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..300  

sonusSs7TimerTScga 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.57
This timer is started when initial demand continuity check fails in the SCGA group. The valid range for this timer is 0 to 120 seconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..120  

sonusSs7TimerTScgad 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.58
This timer is started failure of demand continuity check in the SCGA group.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 5..120  

sonusSs7NodeProfileState 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.59
The administrative state of this object.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disabled(1), enabled(2)  

sonusSs7NodeProfileRowStatus 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.60
Tok_String
Status: current Access: read-write
OBJECT-TYPE    
  RowStatus  

sonusSs7NodeProfileNetworkInd 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.61
The setting of the Network Indicator used for this SS7 Node entry.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER intl0(1), intl1(2), natl0(3), natl1(4)  

sonusSs7SlsBits 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.62
The number of SLS bits to use
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 4..8  

sonusSs7TimerTA 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.63
The Bellcore specific timer TA is started when a RLC message is sent by the switch. The value of this timer is 0 to 1000 milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1000  

sonusSs7TimerTBlom 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.64
The Bellcore specific timer TBlom is started when blocking a circuit due to a BLO, and after any call is released; used to notify maintenance.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 240..360  

sonusSs7TimerTCotd 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.65
The Bellcore specific timer TCOTd is started when sending IAM requesting continuity check. The value of this timer is in milliseconds.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..500  

sonusSs7TimerTCotl 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.66
The Bellcore specific timer TCOTl is started when receiving second COT coded failed, awaiting receipt of CCR.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 240..300  

sonusSs7TimerTSus 1.3.6.1.4.1.2879.2.5.3.1.3.2.1.67
The Bellcore specific timer TSUS is started when a SUS message is sent by the terminating switch, awaiting called party off-hook or REL.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 14..16  

sonusSs7ServicesMIBNotifications 1.3.6.1.4.1.2879.2.5.3.2
OBJECT IDENTIFIER    

sonusSs7ServicesMIBNotificationsPrefix 1.3.6.1.4.1.2879.2.5.3.2.0
OBJECT IDENTIFIER    

sonusSs7ServicesMIBNotificationsObjects 1.3.6.1.4.1.2879.2.5.3.2.1
OBJECT IDENTIFIER    

sonusSs7NodeServiceType 1.3.6.1.4.1.2879.2.5.3.2.1.1
The type of service supported by this SS7 node connection (ISUP or TCAP).
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..6)  

sonusSs7NodeStateChangeReason 1.3.6.1.4.1.2879.2.5.3.2.1.2
The reason why this SS7 node connection has changed state.
Status: current Access: read-only
OBJECT-TYPE    
  DisplayString Size(1..101)  

sonusSs7NodeCurrentState 1.3.6.1.4.1.2879.2.5.3.2.1.3
The current state of this SS7 node connection.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER offline(1), active(2), initializing(3), failed(4), disabled(5), congested(6)  

sonusSs7NodeAffectedPointCode 1.3.6.1.4.1.2879.2.5.3.2.1.4
The SS7 point code affected by this MTP state change.
Status: current Access: read-only
OBJECT-TYPE    
  PointCode  

sonusSs7NodeConnectionEstablishedNotification 1.3.6.1.4.1.2879.2.5.3.2.0.1
This trap indicates that a connection has been established to the specified SS7 gateway. Information provided by this trap includes the name of the connected SS7 node, the name of the SS7 gateway on which the node resides, and the type of SS7 service that has been established (ISUP or TCAP).
Status: current Access: read-only
NOTIFICATION-TYPE    

sonusSs7NodeConnectionFailedNotification 1.3.6.1.4.1.2879.2.5.3.2.0.2
This trap indicates that an established connection to an SS7 gateway has failed. Information provided by this trap includes the name of the failed SS7 node, the name of the SS7 gateway on which the node resides, the type of SS7 service affected by this failure, and the reason why the connection has failed.
Status: current Access: read-only
NOTIFICATION-TYPE    

sonusSs7NodeConnectionStateChangeNotification 1.3.6.1.4.1.2879.2.5.3.2.0.3
This trap indicates that an established connection to an SS7 gateway has changed state. Information provided by this trap includes the name of the affected SS7 node, the name of the SS7 gateway on which the node resides, the type of SS7 service affected by this failure, the new state of the node, and the reason for the state change.
Status: current Access: read-only
NOTIFICATION-TYPE    

sonusSs7NodeMtpStateChangeNotification 1.3.6.1.4.1.2879.2.5.3.2.0.4
This trap indicates that a MTP state change event has been received from the SS7 gateway, affecting the specified destination (or remote) point code (DPC). Information provided by this trap includes the name of the affected SS7 node, the name of the SS7 gateway on which the node resides, the updated MTP state, and the DPC affected by this event.
Status: current Access: read-only
NOTIFICATION-TYPE