SLE-ISIS-MIB

File: SLE-ISIS-MIB.mib (105824 bytes)

Imported modules

DASAN-SMI SLE-TC-MIB SNMPv2-CONF
SNMPv2-SMI

Imported symbols

sleMgmt SleControlStatusType SleControlRequestResultType
OBJECT-GROUP TimeTicks IpAddress
Integer32 Unsigned32 Gauge32
OBJECT-TYPE MODULE-IDENTITY

Defined Types

SleISISProcInfoEntry  
SEQUENCE    
  sleISISProcInfoInstanceID Integer32
  sleISISProcInfoTag OCTET STRING
  sleISISProcBfdAllInterface INTEGER
  sleISISProcCapCspf INTEGER
  sleISISProcDynHostname INTEGER
  sleISISProcDynHostnameAreaTag INTEGER
  sleISISProcIgnLspErr INTEGER
  sleISISProcRouteHighPriorityTag Gauge32
  sleISISProcIspfLevel INTEGER
  sleISISProcIsTypeLevel INTEGER
  sleISISProcLspGenInterval INTEGER
  sleISISProcLspGenIntervalLevel INTEGER
  sleISISProcLspMtu INTEGER
  sleISISProcLspMtuLevel INTEGER
  sleISISProcLspRefreshInterval INTEGER
  sleISISProcMaxAreaAddressNum INTEGER
  sleISISProcMaxLspLifetime INTEGER
  sleISISProcMetricStyle INTEGER
  sleISISProcMetricStyleLevel INTEGER
  sleISISProcMplsTrafficEngLevel INTEGER
  sleISISProcMplsTrafficEngRouterID IpAddress
  sleISISProcPrcIntervalExpMinDelay INTEGER
  sleISISProcPrcIntervalExpMaxDelay INTEGER
  sleISISProcProtocolTopolgy INTEGER
  sleISISProcRestartTimerVal INTEGER
  sleISISProcRestartTimerLevel INTEGER
  sleISISProcSpfIntervalExpMin INTEGER
  sleISISProcSpfIntervalExpMax INTEGER
  sleISISProcSpfIntervalExpLevel INTEGER
  sleISISProcAuthMode INTEGER
  sleISISProcAuthModeLevel INTEGER
  sleISISProcAuthSendOnly INTEGER
  sleISISProcAuthSendOnlyLevel INTEGER
  sleISISProcDomPassVal OCTET STRING
  sleISISProcDomPassAuthSnp INTEGER
  sleISISProcAreaPassVal OCTET STRING
  sleISISProcAreaPassAuthSnp INTEGER
  sleISISProcSetOverloadBit INTEGER
  sleISISProcSetOverloadBitOnStartup INTEGER
  sleISISProcSetOverloadBitOnStartupInterval Integer32
  sleISISProcSetOverloadBitSuppress INTEGER
  sleISISProcWaitTimerVal INTEGER
  sleISISProcWaitTimerLevel INTEGER
  sleISISProcAuthenKeyChainL1 OCTET STRING
  sleISISProcAuthenKeyChainL2 OCTET STRING
  sleISISProcAuthenKeyChainL1L2 OCTET STRING

SleISISProcNetEntry  
SEQUENCE    
  sleISISProcNetInstanceID Integer32
  sleISISProcNetTitle OCTET STRING

SleISISProcDistanceV4Entry  
SEQUENCE    
  sleISISProcDistanceV4InstanceID Integer32
  sleISISProcDistanceV4Dist Integer32
  sleISISProcDistanceV4SytemID OCTET STRING
  sleISISProcDistanceV4AccessList OCTET STRING

SlsISISIfEntry  
SEQUENCE    
  sleISISIfIndex Integer32
  sleISISIfMplsLdpIgpSync INTEGER
  sleISISIfIpRouter INTEGER
  sleISISIfAuthSendLevel1 INTEGER
  sleISISIfAuthSendLevel2 INTEGER
  sleISISIfAuthModeMd5Levle1 INTEGER
  sleISISIfAuthModeMd5Levle2 INTEGER
  sleISISIfAuthModeTextLevle1 INTEGER
  sleISISIfAuthModeTextLevle2 INTEGER
  sleISISIfAuthKeyChainLevle1 OCTET STRING
  sleISISIfAuthKeyChainLevle2 OCTET STRING
  sleISISIfBfd INTEGER
  sleISISIfBfdDisable INTEGER
  sleISISIfCircuitType INTEGER
  sleISISIfCsnpIntervalLevel1 Integer32
  sleISISIfCsnpIntervalLevel2 Integer32
  sleISISIfHelloPadding INTEGER
  sleISISIfHelloIntervalLevel1 Integer32
  sleISISIfHelloIntervalLevel2 Integer32
  sleISISIfHelloIntervalMinimalLevel1 INTEGER
  sleISISIfHelloIntervalMinimalLevel2 INTEGER
  sleISISIfHelloMultiplierLevel1 Integer32
  sleISISIfHelloMultiplierLevel2 Integer32
  sleISISIfLspInterval Unsigned32
  sleISISIfMeshGroup Unsigned32
  sleISISIfMetricLevel1 Integer32
  sleISISIfMetricLevel2 Integer32
  sleISISIfNetwork INTEGER
  sleISISIfPriorityLevel1 Integer32
  sleISISIfPriorityLevel2 Integer32
  sleISISIfRestartHelloIntervalLevel1 Integer32
  sleISISIfRestartHelloIntervalLevel2 Integer32
  sleISISIfRetransmitInterval Integer32
  sleISISIfWideMetricLevel1 Integer32
  sleISISIfWideMetricLevel2 Integer32

SleISISIfStatusEntry  
SEQUENCE    
  sleISISIfStatusIfIndex Integer32
  sleIsisIfStatusIfStatus INTEGER
  sleIsisIfStatusIsisTag OCTET STRING
  sleIsisIfStatusNetworkType INTEGER
  sleIsisIfStatusCircuitType INTEGER
  sleIsisIfStatusLocalCircuitId Integer32
  sleIsisIfStatusExtendedLocalCircuitId Integer32
  sleIsisIfStatusLocalSnpa OCTET STRING
  sleIsisIfStatusLdpSyncHoldTimer Integer32
  sleIsisIfStatusLdpSyncRemainingTime Integer32
  sleIsisIfStatusCircuitL1Metric Integer32
  sleIsisIfStatusCircuitL1WideMetric Integer32
  sleIsisIfStatusCircuitL1Priority Integer32
  sleIsisIfStatusCircuitL1CircuitId Integer32
  sleIsisIfStatusCircuitL1ActiveAdjacencies Integer32
  sleIsisIfStatusCircuitL1LscpMtu Integer32
  sleIsisIfStatusCircuitL2Metric Integer32
  sleIsisIfStatusCircuitL2WideMetric Integer32
  sleIsisIfStatusCircuitL2Priority Integer32
  sleIsisIfStatusCircuitL2CircuitId Integer32
  sleIsisIfStatusCircuitL2ActiveAdjacencies Integer32
  sleIsisIfStatusCircuitL2LscpMtu Integer32
  sleIsisIfStatusL1HelloTimerBroadcast OCTET STRING
  sleIsisIfStatusL2HelloTimerBroadcast OCTET STRING
  sleIsisIfStatusL1HellotimerPoint2Point OCTET STRING
  sleIsisIfStatusL2HellotimerPoint2Point OCTET STRING

SleISISInstIfEntry  
SEQUENCE    
  sleISISInstIfInstanceId Integer32
  sleISISInstIfInterfaceId Integer32
  sleISISPassiveInterface INTEGER

SleISISInstRedistProtocolEntry  
SEQUENCE    
  sleISISInstRedistProtocolInstanceId Integer32
  sleISISInstRedistProtocolId INTEGER
  sleISISInstRedistProtocolMetric Gauge32
  sleISISInstRedistProtocolMetricType INTEGER
  sleISISInstRedistProtocolRouteLevelType INTEGER
  sleISISInstRedistProtocolRouteMapName OCTET STRING

SleISISInstRedistIsisProtocolEntry  
SEQUENCE    
  sleISISInstRedistIsisProtocolInstanceId Integer32
  sleISISInstRedistIsisProtocolInterAreaFromLv1ToLv2 INTEGER
  sleISISInstRedistIsisProtocolLv1Lv2DistributeList OCTET STRING
  sleISISInstRedistIsisProtocolInterAreaFromLv2ToLv1 INTEGER
  sleISISInstRedistIsisProtocolLv2Lv1DistributeList OCTET STRING

SleISISSummanryAddressEntry  
SEQUENCE    
  sleISISSummanryAddressInstanceId Integer32
  sleISISSummanryAddressIpValue IpAddress
  sleISISSummanryAddressIpNetmask Integer32
  sleISISSummanryAddressLevel INTEGER
  sleISISSummanryAddressMetric Integer32

SleISISDatabaseEntry  
SEQUENCE    
  sleISISDatabaseTag OCTET STRING
  sleISISDatabaseLevel Integer32
  sleISISDatabaseLspId OCTET STRING
  sleISISDatabaseLspSeqNum OCTET STRING
  sleISISDatabaseLspChecksum OCTET STRING
  sleISISDatabaseLspHoldtime OCTET STRING
  sleISISDatabaseAtt Integer32
  sleISISDatabaseP Integer32
  sleISISDatabaseOl Integer32

SleISISDatabaseDetailEntry  
SEQUENCE    
  sleISISDatabaseDetailTag OCTET STRING
  sleISISDatabaseDetailLevel INTEGER
  sleISISDatabaseDetailLspId OCTET STRING
  sleISISDatabaseDetailType INTEGER
  sleISISDatabaseDetailIndex Integer32
  sleISISDatabaseDetailPad OCTET STRING
  sleISISDatabaseDetailValue Integer32
  sleISISDatabaseDetailDescription OCTET STRING

Defined Values

sleISIS 1.3.6.1.4.1.6296.101.56
This MIB contains information about RIP version 2.
MODULE-IDENTITY    

sleISISBase 1.3.6.1.4.1.6296.101.56.1
OBJECT IDENTIFIER    

sleISISBaseInfo 1.3.6.1.4.1.6296.101.56.1.1
OBJECT IDENTIFIER    

sleISISRestartSuppressAdjacency 1.3.6.1.4.1.6296.101.56.1.1.1
ISIS restart suppress-adjacency
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISRestartHelper 1.3.6.1.4.1.6296.101.56.1.1.2
ISIS restart helper
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISRestartGracePeriod 1.3.6.1.4.1.6296.101.56.1.1.3
ISIS Graceful-restart period. Seconds: <1-65535> Specify the number of seconds in the grace period.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..65535  

sleISISBaseControl 1.3.6.1.4.1.6296.101.56.1.2
OBJECT IDENTIFIER    

sleISISControlRequest 1.3.6.1.4.1.6296.101.56.1.2.1
The request of a user command
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER setISISRestartSuppressAdj(1), setISISRestartHelper(2), setISISRestartGracefulPeriod(3), clearISISClnsNeighbors(4), clearISISClnsIsNeighbors(5), clearISISCounter(6), clearISISInterfaceCounter(7), clearISISProcess(8), clearISISRoute(9), retartISISGraceful(10), snmpRestartISIS(11)  

sleISISControlStatus 1.3.6.1.4.1.6296.101.56.1.2.2
The request of a user command
Status: current Access: read-only
OBJECT-TYPE    
  SleControlStatusType  

sleISISControlTimer 1.3.6.1.4.1.6296.101.56.1.2.3
The maximum time for the manager for a long running user command
Status: current Access: read-write
OBJECT-TYPE    
  Gauge32  

sleISISControlTimeStamp 1.3.6.1.4.1.6296.101.56.1.2.4
The time stamp of the last command(end of command)
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

sleISISControlReqResult 1.3.6.1.4.1.6296.101.56.1.2.5
The result of the last user command
Status: current Access: read-only
OBJECT-TYPE    
  SleControlRequestResultType  

sleISISControlRestartSuppressAdjacency 1.3.6.1.4.1.6296.101.56.1.2.6
Description.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER diable(0), enable(1)  

sleISISControlRestartHelper 1.3.6.1.4.1.6296.101.56.1.2.7
Description.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISControlRestartPeriod 1.3.6.1.4.1.6296.101.56.1.2.8
ISIS Graceful-restart period.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..1800  

sleISISControlClearSystemId 1.3.6.1.4.1.6296.101.56.1.2.9
System-ID Neighbor system ID in XXXX. XXXX. XXXX format.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

sleISISControlClearIfName 1.3.6.1.4.1.6296.101.56.1.2.10
Interface Name of ISIS for clear
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

sleISISControlClearRouteTag 1.3.6.1.4.1.6296.101.56.1.2.11
Routing area tag
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

sleISISControlClearRouteMode 1.3.6.1.4.1.6296.101.56.1.2.12
The route mode to clear. Redistribution: Clear ISIS local redistribution routes. all: Clear all of the ISIS routing table.s
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER redistribution(1), all(2)  

sleISISBaseNotification 1.3.6.1.4.1.6296.101.56.1.3
OBJECT IDENTIFIER    

sleISISProc 1.3.6.1.4.1.6296.101.56.2
OBJECT IDENTIFIER    

sleISISProcInfo 1.3.6.1.4.1.6296.101.56.2.1
OBJECT IDENTIFIER    

sleISISProcInfoTable 1.3.6.1.4.1.6296.101.56.2.1.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SleISISProcInfoEntry

sleISISProcInfoEntry 1.3.6.1.4.1.6296.101.56.2.1.1.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SleISISProcInfoEntry  

sleISISProcInfoInstanceID 1.3.6.1.4.1.6296.101.56.2.1.1.1.1
Instance ID of ISIS Process
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

sleISISProcInfoTag 1.3.6.1.4.1.6296.101.56.2.1.1.1.2
ISIS Process Tag
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISProcBfdAllInterface 1.3.6.1.4.1.6296.101.56.2.1.1.1.3
Enable BFD on all interfaces
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISProcCapCspf 1.3.6.1.4.1.6296.101.56.2.1.1.1.4
Enable Constrained Shortest Path First
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISProcDynHostname 1.3.6.1.4.1.6296.101.56.2.1.1.1.5
Enable dynamic hostname
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISProcDynHostnameAreaTag 1.3.6.1.4.1.6296.101.56.2.1.1.1.6
Use area-tag as hostname
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISProcIgnLspErr 1.3.6.1.4.1.6296.101.56.2.1.1.1.7
Ignore LSPs with bad checksums
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISProcRouteHighPriorityTag 1.3.6.1.4.1.6296.101.56.2.1.1.1.8
Sets the high priority of route
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 1..4294967295  

sleISISProcIspfLevel 1.3.6.1.4.1.6296.101.56.2.1.1.1.9
Enable incremental SPF for ISIS proces
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), level1(1), level1To2(2), level2only(3)  

sleISISProcIsTypeLevel 1.3.6.1.4.1.6296.101.56.2.1.1.1.10
IS Level for ISIS process
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), level1(1), level1To2(2), level2Only(3)  

sleISISProcLspGenInterval 1.3.6.1.4.1.6296.101.56.2.1.1.1.11
Minimum interval between regenerating same LSP
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..120  

sleISISProcLspGenIntervalLevel 1.3.6.1.4.1.6296.101.56.2.1.1.1.12
IS Level for ISIS process
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), level1(1), level2(2)  

sleISISProcLspMtu 1.3.6.1.4.1.6296.101.56.2.1.1.1.13
Set lsp MTU in bytes
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 512..1492  

sleISISProcLspMtuLevel 1.3.6.1.4.1.6296.101.56.2.1.1.1.14
IS Level for ISIS process
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), level1(1), level1To2(2), level2Only(3)  

sleISISProcLspRefreshInterval 1.3.6.1.4.1.6296.101.56.2.1.1.1.15
Set LSP refresh interval
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

sleISISProcMaxAreaAddressNum 1.3.6.1.4.1.6296.101.56.2.1.1.1.16
Configure isis maximum area address
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 3..254  

sleISISProcMaxLspLifetime 1.3.6.1.4.1.6296.101.56.2.1.1.1.17
Set maximum LSP lifetime
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 350..65535  

sleISISProcMetricStyle 1.3.6.1.4.1.6296.101.56.2.1.1.1.18
Use old-style (ISO 10589) or new-style packet formats
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), wide(1), wideTransition(2), transition(3), narrowTransition(4)  

sleISISProcMetricStyleLevel 1.3.6.1.4.1.6296.101.56.2.1.1.1.19
Level of Metric Style
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), level1(1), level1To2(2), level2Only(3)  

sleISISProcMplsTrafficEngLevel 1.3.6.1.4.1.6296.101.56.2.1.1.1.20
Traffice Engine level of MPLS routing protocol
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), level1(1), level2(2)  

sleISISProcMplsTrafficEngRouterID 1.3.6.1.4.1.6296.101.56.2.1.1.1.21
Traffice Engine Router ID of MPLS routing protoco
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

sleISISProcPrcIntervalExpMinDelay 1.3.6.1.4.1.6296.101.56.2.1.1.1.22
Use exponential backoff min delays between PRC calculation
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

sleISISProcPrcIntervalExpMaxDelay 1.3.6.1.4.1.6296.101.56.2.1.1.1.23
Use exponential backoff max delays between PRC calculation
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

sleISISProcProtocolTopolgy 1.3.6.1.4.1.6296.101.56.2.1.1.1.24
Protocol Topology
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISProcRestartTimerVal 1.3.6.1.4.1.6296.101.56.2.1.1.1.25
Restart timer interval
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 5..65535  

sleISISProcRestartTimerLevel 1.3.6.1.4.1.6296.101.56.2.1.1.1.26
Restart timer level
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), level1(1), level1To2(2), level2Only(3)  

sleISISProcSpfIntervalExpMin 1.3.6.1.4.1.6296.101.56.2.1.1.1.27
Use exponential backoff min delays between SPF calculations
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

sleISISProcSpfIntervalExpMax 1.3.6.1.4.1.6296.101.56.2.1.1.1.28
Use exponential backoff max delays between SPF calculations
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 0..2147483647  

sleISISProcSpfIntervalExpLevel 1.3.6.1.4.1.6296.101.56.2.1.1.1.29
Level of SPF Interval Exp
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), level1(1), level2(2)  

sleISISProcAuthMode 1.3.6.1.4.1.6296.101.56.2.1.1.1.30
Authentication mode of ISIS Process
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), md5(1), text(2), md5Text(3)  

sleISISProcAuthModeLevel 1.3.6.1.4.1.6296.101.56.2.1.1.1.31
Authentication level of ISIS Process
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), level1(1), level2(2)  

sleISISProcAuthSendOnly 1.3.6.1.4.1.6296.101.56.2.1.1.1.32
Authentication send-only
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISProcAuthSendOnlyLevel 1.3.6.1.4.1.6296.101.56.2.1.1.1.33
Level of Authentication send-only
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), level1(1), level2(2)  

sleISISProcDomPassVal 1.3.6.1.4.1.6296.101.56.2.1.1.1.34
ISIS Routing domain password
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

sleISISProcDomPassAuthSnp 1.3.6.1.4.1.6296.101.56.2.1.1.1.35
SNP Authentication of ISIS Routing domain
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), validate(1), sendOnly(2)  

sleISISProcAreaPassVal 1.3.6.1.4.1.6296.101.56.2.1.1.1.36
ISIS Routing Area password
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

sleISISProcAreaPassAuthSnp 1.3.6.1.4.1.6296.101.56.2.1.1.1.37
SNP Authentication of ISIS Routing Area
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), validate(1), sendOnly(2)  

sleISISProcSetOverloadBit 1.3.6.1.4.1.6296.101.56.2.1.1.1.38
Signal other routers not to use us in SPF
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISProcSetOverloadBitOnStartup 1.3.6.1.4.1.6296.101.56.2.1.1.1.39
Set overload-bit only temporarily after reboot
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), overload(1), waitForBgp(2)  

sleISISProcSetOverloadBitOnStartupInterval 1.3.6.1.4.1.6296.101.56.2.1.1.1.40
Time in seconds to advertise ourself as overloaded after reboot
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 5..86400  

sleISISProcSetOverloadBitSuppress 1.3.6.1.4.1.6296.101.56.2.1.1.1.41
If overload-bit set, suppress the following types of IP prefixes
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), external(1), interlevel(2)  

sleISISProcWaitTimerVal 1.3.6.1.4.1.6296.101.56.2.1.1.1.42
Set lsp MTU in bytes
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..65535  

sleISISProcWaitTimerLevel 1.3.6.1.4.1.6296.101.56.2.1.1.1.43
IS Level for ISIS process
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), level1(1), level1To2(2), level2Only(3)  

sleISISProcAuthenKeyChainL1 1.3.6.1.4.1.6296.101.56.2.1.1.1.44
The authentication key-chain with level1
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISProcAuthenKeyChainL2 1.3.6.1.4.1.6296.101.56.2.1.1.1.45
The authentication key-chain with level2.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISProcAuthenKeyChainL1L2 1.3.6.1.4.1.6296.101.56.2.1.1.1.46
The authentication key-chain with level1 and level2.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISProcInfoControl 1.3.6.1.4.1.6296.101.56.2.1.2
OBJECT IDENTIFIER    

sleISISProcInfoControlRequest 1.3.6.1.4.1.6296.101.56.2.1.2.1
Description.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER createISISProcess(1), deleteISISProcess(2), setISISProcBfdAllInterface(3), setISISProcCapabilityCspf(4), setISISProcDynamicHostname(5), setISISProcIgnoreLspErr(6), setISISProcRouteHighPriorityTag(7), setISISProcIspfLevel(8), setISISProcIsTypeLevel(9), setISISProcLspGenInterval(10), setISISProcLspMtu(11), setISISProcLspRefreshInterval(12), setISISProcMaxAreaAddress(13), setISISProcMaxLspLifetime(14), setISISProcMetricStyle(15), setISISProcMplsTrafficEngLevel(16), setISISProcMplsTrafficEngRouterID(17), setISISProcPrcIntervalExp(18), setISISProcProtocoalTopology(19), setISISProcRestartTimer(20), setISISProcSpfIntervalExp(21), setISISProcAuthMode(22), setISISProcAuthSendOnly(23), setISISProcDomPassword(24), setISISProcAreaPassword(25), setISISProcSetOverloadBit(26), setISISProcWaitTimer(27), setISISProcAuthenKeyChain(28), delISISProcAuthenKeyChain(29)  

sleISISProcInfoControlStatus 1.3.6.1.4.1.6296.101.56.2.1.2.2
Description.
Status: current Access: read-only
OBJECT-TYPE    
  SleControlStatusType  

sleISISProcInfoControlTimer 1.3.6.1.4.1.6296.101.56.2.1.2.3
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Gauge32  

sleISISProcInfoControlTimeStamp 1.3.6.1.4.1.6296.101.56.2.1.2.4
Description.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

sleISISProcInfoControlReqResult 1.3.6.1.4.1.6296.101.56.2.1.2.5
Description.
Status: current Access: read-only
OBJECT-TYPE    
  SleControlRequestResultType  

sleISISProcInfoControlTag 1.3.6.1.4.1.6296.101.56.2.1.2.6
ISIS Process Tag
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

sleISISProcInfoControlBfdAllInterface 1.3.6.1.4.1.6296.101.56.2.1.2.7
Enable BFD on all interfaces
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISProcInfoControlCapCspf 1.3.6.1.4.1.6296.101.56.2.1.2.8
Enable Constrained Shortest Path First
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISProcInfoControlDynHostname 1.3.6.1.4.1.6296.101.56.2.1.2.9
Enable dynamic hostname
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISProcInfoControlDynHostnameAreaTag 1.3.6.1.4.1.6296.101.56.2.1.2.10
Use area-tag as hostname
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISProcInfoControlIgnLspErr 1.3.6.1.4.1.6296.101.56.2.1.2.11
Ignore LSPs with bad checksums
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISProcInfoControlRouteHighPriorityTag 1.3.6.1.4.1.6296.101.56.2.1.2.12
Sets the high priority of route
Status: current Access: read-write
OBJECT-TYPE    
  Gauge32 1..4294967295  

sleISISProcInfoControlIspfLevel 1.3.6.1.4.1.6296.101.56.2.1.2.13
Enable incremental SPF for ISIS proces
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), level1(1), level1To2(2), level2Only(3)  

sleISISProcInfoControlIsTypeLevel 1.3.6.1.4.1.6296.101.56.2.1.2.14
IS Level for ISISprocess
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), level1(1), level1To2(2), level2Only(3)  

sleISISProcInfoControlLspGenInterval 1.3.6.1.4.1.6296.101.56.2.1.2.15
Minimum interval between regenerating same LSP
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..120  

sleISISProcInfoControlLspGenIntervalLevel 1.3.6.1.4.1.6296.101.56.2.1.2.16
IS Level for ISISprocess
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), level1(1), level2(2)  

sleISISProcInfoControlLspMtu 1.3.6.1.4.1.6296.101.56.2.1.2.17
Set lsp MTU in bytes
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 512..1492  

sleISISProcInfoControlLspMtuLevel 1.3.6.1.4.1.6296.101.56.2.1.2.18
IS Level for ISISprocess
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), level1(1), level1To2(2), level2Only(3)  

sleISISProcInfoControlLspRefreshInterval 1.3.6.1.4.1.6296.101.56.2.1.2.19
Set LSP refresh interval
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

sleISISProcInfoControlMaxAreaAddressNum 1.3.6.1.4.1.6296.101.56.2.1.2.20
Configure isis maximum area address
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 3..254  

sleISISProcInfoControlMaxLspLifetime 1.3.6.1.4.1.6296.101.56.2.1.2.21
Set maximum LSP lifetime
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 350..65535  

sleISISProcInfoControlMetricStyle 1.3.6.1.4.1.6296.101.56.2.1.2.22
Use old-style (ISO 10589) or new-style packet formats
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), wide(1), wideTransition(2), transition(3), narrowTransition(4)  

sleISISProcInfoControlMetricStyleLevel 1.3.6.1.4.1.6296.101.56.2.1.2.23
Level of Metric Style
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), level1(1), level1To2(2), level2Only(3)  

sleISISProcInfoControlMplsTrafficEngLevel 1.3.6.1.4.1.6296.101.56.2.1.2.24
Traffice Engine level of MPLS routing protocol
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), level1(1), level2(2)  

sleISISProcInfoControlMplsTrafficEngRouterID 1.3.6.1.4.1.6296.101.56.2.1.2.25
Traffice Engine Router ID of MPLS routing protocol
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sleISISProcInfoControlPrcIntervalExpMinDelay 1.3.6.1.4.1.6296.101.56.2.1.2.26
Use exponential backoff min delays between PRC calculation
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sleISISProcInfoControlPrcIntervalExpMaxDelay 1.3.6.1.4.1.6296.101.56.2.1.2.27
Use exponential backoff max delays between PRC calculation
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sleISISProcInfoControlProtocolTopolgy 1.3.6.1.4.1.6296.101.56.2.1.2.28
Protocol Topology
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISProcInfoControlRestartTimerVal 1.3.6.1.4.1.6296.101.56.2.1.2.29
Protocol Topology
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 5..65535  

sleISISProcInfoControlRestartTimerLevel 1.3.6.1.4.1.6296.101.56.2.1.2.30
Restart timer level
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), level1(1), level1To2(2), level2Only(3)  

sleISISProcInfoControlSpfIntervalExpMin 1.3.6.1.4.1.6296.101.56.2.1.2.31
Use exponential backoff min delays between SPF calculations
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sleISISProcInfoControlSpfIntervalExpMax 1.3.6.1.4.1.6296.101.56.2.1.2.32
Use exponential backoff max delays between SPF calculations
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 0..2147483647  

sleISISProcInfoControlSpfIntervalExpLevel 1.3.6.1.4.1.6296.101.56.2.1.2.33
Level of SPF Interval Exp
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), level1(1), level2(2)  

sleISISProcInfoControlAuthMode 1.3.6.1.4.1.6296.101.56.2.1.2.34
Authentication mode of ISIS Process
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), md5(1), text(2), md5Text(3)  

sleISISProcInfoControlAuthModeLevel 1.3.6.1.4.1.6296.101.56.2.1.2.35
Authentication level of ISIS Process
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), level1(1), level2(2)  

sleISISProcInfoControlAuthSendOnly 1.3.6.1.4.1.6296.101.56.2.1.2.36
Authentication send-only
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISProcInfoControlAuthSendOnlyLevel 1.3.6.1.4.1.6296.101.56.2.1.2.37
Level of Authentication send-only
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), level1(1), level2(2)  

sleISISProcInfoControlDomPassVal 1.3.6.1.4.1.6296.101.56.2.1.2.38
ISIS Routing domain password
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

sleISISProcInfoControlDomPassAuthSnp 1.3.6.1.4.1.6296.101.56.2.1.2.39
SNP Authentication of ISIS Routing domain
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), validate(1), sendOnly(2)  

sleISISProcInfoControlAreaPassVal 1.3.6.1.4.1.6296.101.56.2.1.2.40
ISIS Routing Area password
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

sleISISProcInfoControlAreaPassAuthSnp 1.3.6.1.4.1.6296.101.56.2.1.2.41
SNP Authentication of ISIS Routing domain
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), validate(1), sendOnly(2)  

sleISISProcInfoControlSetOverloadBit 1.3.6.1.4.1.6296.101.56.2.1.2.42
Signal other routers not to use us in SPF
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISProcInfoControlSetOverloadBitOnStartup 1.3.6.1.4.1.6296.101.56.2.1.2.43
Set overload-bit only temporarily after reboot
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), overload(1), waitForBgp(2)  

sleISISProcInfoControlSetOverloadBitOnStartupInterval 1.3.6.1.4.1.6296.101.56.2.1.2.44
Time in seconds to advertise ourself as overloaded after reboot
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 5..86400  

sleISISProcInfoControlSetOverloadBitSuppress 1.3.6.1.4.1.6296.101.56.2.1.2.45
If overload-bit set, suppress the following types of IP prefixes
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), external(1), interlevel(2)  

sleISISProcControlWaitTimerVal 1.3.6.1.4.1.6296.101.56.2.1.2.46
Set lsp MTU in bytes
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER 1..65535  

sleISISProcControlWaitTimerLevel 1.3.6.1.4.1.6296.101.56.2.1.2.47
Enable incremental SPF for ISIS proces
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), level1(1), level1To2(2), level2Only(3)  

sleISISProcControlAuthenkeyChain 1.3.6.1.4.1.6296.101.56.2.1.2.48
The authentication key-chain word.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

sleISISProcControlAuthenkeyChainLevel 1.3.6.1.4.1.6296.101.56.2.1.2.49
The authentication key-chain level.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER level1(1), level2(2), level1And2(3)  

sleISISProcInfoNotification 1.3.6.1.4.1.6296.101.56.2.1.3
OBJECT IDENTIFIER    

sleISISProcNet 1.3.6.1.4.1.6296.101.56.2.2
OBJECT IDENTIFIER    

sleISISProcNetTable 1.3.6.1.4.1.6296.101.56.2.2.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SleISISProcNetEntry

sleISISProcNetEntry 1.3.6.1.4.1.6296.101.56.2.2.1.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SleISISProcNetEntry  

sleISISProcNetInstanceID 1.3.6.1.4.1.6296.101.56.2.2.1.1.1
Description.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

sleISISProcNetTitle 1.3.6.1.4.1.6296.101.56.2.2.1.1.2
Description.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISProcNetControl 1.3.6.1.4.1.6296.101.56.2.2.2
OBJECT IDENTIFIER    

sleISISProcNetControlRequest 1.3.6.1.4.1.6296.101.56.2.2.2.1
Description.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER createISISProcNet(1), deleteISISProcNet(2)  

sleISISProcNetControlStatus 1.3.6.1.4.1.6296.101.56.2.2.2.2
Description.
Status: current Access: read-only
OBJECT-TYPE    
  SleControlStatusType  

sleISISProcNetControlTimer 1.3.6.1.4.1.6296.101.56.2.2.2.3
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Gauge32  

sleISISProcNetControlTimeStamp 1.3.6.1.4.1.6296.101.56.2.2.2.4
Description.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

sleISISProcNetControlReqResult 1.3.6.1.4.1.6296.101.56.2.2.2.5
Description.
Status: current Access: read-only
OBJECT-TYPE    
  SleControlRequestResultType  

sleISISProcNetControlInstanceID 1.3.6.1.4.1.6296.101.56.2.2.2.6
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

sleISISProcNetControlTitle 1.3.6.1.4.1.6296.101.56.2.2.2.7
Description.
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(0..512)  

sleISISProcNetNotification 1.3.6.1.4.1.6296.101.56.2.2.3
OBJECT IDENTIFIER    

sleISISProcDistanceV4 1.3.6.1.4.1.6296.101.56.2.3
OBJECT IDENTIFIER    

sleISISProcDistanceV4Table 1.3.6.1.4.1.6296.101.56.2.3.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SleISISProcDistanceV4Entry

sleISISProcDistanceV4Entry 1.3.6.1.4.1.6296.101.56.2.3.1.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SleISISProcDistanceV4Entry  

sleISISProcDistanceV4InstanceID 1.3.6.1.4.1.6296.101.56.2.3.1.1.1
ISIS Instance ID
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

sleISISProcDistanceV4Dist 1.3.6.1.4.1.6296.101.56.2.3.1.1.2
ISIS Administrative Distance range
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..255  

sleISISProcDistanceV4SytemID 1.3.6.1.4.1.6296.101.56.2.3.1.1.3
Source ID in XXXX.XXXX.XXXX format.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(0..112)  

sleISISProcDistanceV4AccessList 1.3.6.1.4.1.6296.101.56.2.3.1.1.4
Access-list name.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISProcDistanceV4Control 1.3.6.1.4.1.6296.101.56.2.3.2
OBJECT IDENTIFIER    

sleISISProcDistanceV4ControlRequest 1.3.6.1.4.1.6296.101.56.2.3.2.1
Description.
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER createRIPNetworkIfname(1), deleteRIPNetworkIfname(2)  

sleISISProcDistanceV4ControlStatus 1.3.6.1.4.1.6296.101.56.2.3.2.2
Description.
Status: current Access: read-only
OBJECT-TYPE    
  SleControlStatusType  

sleISISProcDistanceV4ControlTimer 1.3.6.1.4.1.6296.101.56.2.3.2.3
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Gauge32  

sleISISProcDistanceV4TimeStamp 1.3.6.1.4.1.6296.101.56.2.3.2.4
Description.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

sleISISProcDistanceV4ntrolReqResult 1.3.6.1.4.1.6296.101.56.2.3.2.5
Description.
Status: current Access: read-only
OBJECT-TYPE    
  SleControlRequestResultType  

sleISISProcDistanceV4ControlInstanceID 1.3.6.1.4.1.6296.101.56.2.3.2.6
Set the ISIS Instance ID
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

sleISISProcDistanceV4ControlDist 1.3.6.1.4.1.6296.101.56.2.3.2.7
ISIS Administrative Distance range
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..255  

sleISISProcDistanceV4ControlSytemID 1.3.6.1.4.1.6296.101.56.2.3.2.8
Source ID in XXXX.XXXX.XXXX format.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISProcDistanceV4ControlAccessList 1.3.6.1.4.1.6296.101.56.2.3.2.9
Access-list name.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISProcDistanceV4Notification 1.3.6.1.4.1.6296.101.56.2.3.3
OBJECT IDENTIFIER    

sleISISIf 1.3.6.1.4.1.6296.101.56.3
OBJECT IDENTIFIER    

slsISISIfTable 1.3.6.1.4.1.6296.101.56.3.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SlsISISIfEntry

slsISISIfEntry 1.3.6.1.4.1.6296.101.56.3.1.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SlsISISIfEntry  

sleISISIfIndex 1.3.6.1.4.1.6296.101.56.3.1.1.1
vlan interface index for isis protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

sleISISIfMplsLdpIgpSync 1.3.6.1.4.1.6296.101.56.3.1.1.2
Use this command to enable LDP-ISIS synchronization. 0 : diaable 1 : level-1 2 : level-1-2,(default) 3 : level-2
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER diaable(0), level1(1), level1To2(2), level2(3)  

sleISISIfIpRouter 1.3.6.1.4.1.6296.101.56.3.1.1.3
Use this command to enable ISIS IPv4 routing on the interface. 1 : enable 0 : disable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfAuthSendLevel1 1.3.6.1.4.1.6296.101.56.3.1.1.4
Use this command to set the send-only option to the interface-related packets. 1 : enable 0 : disable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfAuthSendLevel2 1.3.6.1.4.1.6296.101.56.3.1.1.5
Use this command to set the send-only option to the interface-related packets. 1 : enable 0 : disable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfAuthModeMd5Levle1 1.3.6.1.4.1.6296.101.56.3.1.1.6
Use this command to set the MD5 authentication mode. 1 : enable 0 : disable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfAuthModeMd5Levle2 1.3.6.1.4.1.6296.101.56.3.1.1.7
Use this command to set the MD5 authentication mode. 1 : enable 0 : disable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfAuthModeTextLevle1 1.3.6.1.4.1.6296.101.56.3.1.1.8
Use this command to set the MD5 authentication mode. 1 : enable 0 : disable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfAuthModeTextLevle2 1.3.6.1.4.1.6296.101.56.3.1.1.9
Use this command to set the MD5 authentication mode. 1 : enable 0 : disable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfAuthKeyChainLevle1 1.3.6.1.4.1.6296.101.56.3.1.1.10
Use this command to set the key chain to be used for authentication on the interface-related packets. disable : null string
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISIfAuthKeyChainLevle2 1.3.6.1.4.1.6296.101.56.3.1.1.11
Use this command to set the key chain to be used for authentication on the interface-related packets. disable : null string
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISIfBfd 1.3.6.1.4.1.6296.101.56.3.1.1.12
Use this command to enable/disable the BFD check on interface. 1 : enable 0 : disable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfBfdDisable 1.3.6.1.4.1.6296.101.56.3.1.1.13
Use this command to enable/disable the BFD check on interface. 1 : enable 0 : disable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfCircuitType 1.3.6.1.4.1.6296.101.56.3.1.1.14
Use this command to set the circuit type for the interface. 1 : level-1 2 : level-1-2,(default) 3 : level-2
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER level1(1), level1To2(2), level2(3)  

sleISISIfCsnpIntervalLevel1 1.3.6.1.4.1.6296.101.56.3.1.1.15
Use this command to set CSNP (Complete sequence number PDU) interval in seconds. range : 1 - 65535 default : 10
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

sleISISIfCsnpIntervalLevel2 1.3.6.1.4.1.6296.101.56.3.1.1.16
Use this command to set CSNP (Complete sequence number PDU) interval in seconds. range : 1 - 65535 default : 10
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

sleISISIfHelloPadding 1.3.6.1.4.1.6296.101.56.3.1.1.17
Use this command to configure the padding of the ISIS Hello packet. 1 : enable 0 : disable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfHelloIntervalLevel1 1.3.6.1.4.1.6296.101.56.3.1.1.18
Use this command to set the Hello interval in seconds. range : 1 - 65535 default : 10
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

sleISISIfHelloIntervalLevel2 1.3.6.1.4.1.6296.101.56.3.1.1.19
Use this command to set the Hello interval in seconds. range : 1 - 65535 default : 10
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

sleISISIfHelloIntervalMinimalLevel1 1.3.6.1.4.1.6296.101.56.3.1.1.20
Use this command to set the Hello interval in seconds. 1 : enable 0 : disable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfHelloIntervalMinimalLevel2 1.3.6.1.4.1.6296.101.56.3.1.1.21
Use this command to set the Hello interval in seconds. 1 : enable 0 : disable
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfHelloMultiplierLevel1 1.3.6.1.4.1.6296.101.56.3.1.1.22
Use this command to set multiplier for Hello holding time. range : 2 - 10 default : 3
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 2..10  

sleISISIfHelloMultiplierLevel2 1.3.6.1.4.1.6296.101.56.3.1.1.23
Use this command to set multiplier for Hello holding time. range : 2 - 10 default : 3
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 2..10  

sleISISIfLspInterval 1.3.6.1.4.1.6296.101.56.3.1.1.24
Use this command to set the Link State Packet (LSP) transmission interval. range : 1 - 4294967295 default : 33
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

sleISISIfMeshGroup 1.3.6.1.4.1.6296.101.56.3.1.1.25
Use this command to set Mesh Group ID on the current interface. range : 1 - 4294967295 disable : 0
Status: current Access: read-only
OBJECT-TYPE    
  Unsigned32 1..4294967295  

sleISISIfMetricLevel1 1.3.6.1.4.1.6296.101.56.3.1.1.26
Use this command to set default metric for the interface. range : 1 - 63 default : 10
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..63  

sleISISIfMetricLevel2 1.3.6.1.4.1.6296.101.56.3.1.1.27
Use this command to set default metric for the interface. range : 1 - 63 default : 10
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..63  

sleISISIfNetwork 1.3.6.1.4.1.6296.101.56.3.1.1.28
Use this command to change a broadcast interface network type to a point-to-point network type. 0 : disable 1 : broadcast 2 : point-to-point
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER disable(0), broadcast(1), pointToPoint(2)  

sleISISIfPriorityLevel1 1.3.6.1.4.1.6296.101.56.3.1.1.29
Use this command to set the priority for LAN DIS election. range : 0 - 127 default : 64
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..127  

sleISISIfPriorityLevel2 1.3.6.1.4.1.6296.101.56.3.1.1.30
Use this command to set the priority for LAN DIS election. range : 0 - 127 default : 64
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..127  

sleISISIfRestartHelloIntervalLevel1 1.3.6.1.4.1.6296.101.56.3.1.1.31
Use this command to configure the T1 timer, interval of ISIS Hello packet with restart TLV. range : 1 - 65535 default : 3
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

sleISISIfRestartHelloIntervalLevel2 1.3.6.1.4.1.6296.101.56.3.1.1.32
Use this command to configure the T1 timer, interval of ISIS Hello packet with restart TLV. range : 1 - 65535 default : 3
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

sleISISIfRetransmitInterval 1.3.6.1.4.1.6296.101.56.3.1.1.33
Use this command to set LSP retransmission interval. range : 0 - 65535 default : 5
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

sleISISIfWideMetricLevel1 1.3.6.1.4.1.6296.101.56.3.1.1.34
Use this command to set wide metric for the interface. range : 1 - 16777214 default : 10
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..16777214  

sleISISIfWideMetricLevel2 1.3.6.1.4.1.6296.101.56.3.1.1.35
Use this command to set wide metric for the interface. range : 1 - 16777214 default : 10
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..16777214  

sleISISIfControl 1.3.6.1.4.1.6296.101.56.3.2
OBJECT IDENTIFIER    

sleISISIfControlRequest 1.3.6.1.4.1.6296.101.56.3.2.1
Description.
Status: current Access: read-write
OBJECT-TYPE    
  SleControlRequestResultType setISISIfProfile(1)  

sleISISIfControlStatus 1.3.6.1.4.1.6296.101.56.3.2.2
Description.
Status: current Access: read-write
OBJECT-TYPE    
  SleControlStatusType  

sleISISIfControlTimer 1.3.6.1.4.1.6296.101.56.3.2.3
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Gauge32  

sleISISIfControlTimeStamp 1.3.6.1.4.1.6296.101.56.3.2.4
Description.
Status: current Access: read-write
OBJECT-TYPE    
  TimeTicks  

sleISISIfControlReqResult 1.3.6.1.4.1.6296.101.56.3.2.5
Description.
Status: current Access: read-write
OBJECT-TYPE    
  SleControlRequestResultType  

sleISISIfControlIndex 1.3.6.1.4.1.6296.101.56.3.2.6
vlan interface index for isis protocol.
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sleISISIfControlMplsLdpIgpSync 1.3.6.1.4.1.6296.101.56.3.2.7
Use this command to enable LDP-ISIS synchronization. 0 : diaable 1 : level-1 2 : level-1-2,(default) 3 : level-2
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), level1(1), level1To2(2), level2(3)  

sleISISIfControlIpRouter 1.3.6.1.4.1.6296.101.56.3.2.8
Use this command to enable ISIS IPv4 routing on the interface. 1 : enable 0 : disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER dissable(0), enable(1)  

sleISISIfControlAuthSendLevel1 1.3.6.1.4.1.6296.101.56.3.2.9
Use this command to set the send-only option to the interface-related packets. 1 : enable 0 : disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfControlAuthSendLevel2 1.3.6.1.4.1.6296.101.56.3.2.10
Use this command to set the send-only option to the interface-related packets. 1 : enable 0 : disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfControlAuthModeMd5Levle1 1.3.6.1.4.1.6296.101.56.3.2.11
Use this command to set the send-only option to the interface-related packets. 1 : enable 0 : disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfControlAuthModeMd5Levle2 1.3.6.1.4.1.6296.101.56.3.2.12
Use this command to set the send-only option to the interface-related packets. 1 : enable 0 : disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfControlAuthModeTextLevle1 1.3.6.1.4.1.6296.101.56.3.2.13
Use this command to set the send-only option to the interface-related packets. 1 : enable 0 : disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfControlAuthModeTextLevle2 1.3.6.1.4.1.6296.101.56.3.2.14
Use this command to set the send-only option to the interface-related packets. 1 : enable 0 : disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfControlAuthKeyChainLevle1 1.3.6.1.4.1.6296.101.56.3.2.15
Use this command to set the key chain to be used for authentication on the interface-related packets. disable : null string
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

sleISISIfControlAuthKeyChainLevle2 1.3.6.1.4.1.6296.101.56.3.2.16
Use this command to set the key chain to be used for authentication on the interface-related packets. disable : null string
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

sleISISIfControlBfd 1.3.6.1.4.1.6296.101.56.3.2.17
Use this command to enable/disable the BFD check on interface. 1 : enable 0 : disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfControlBfdDisable 1.3.6.1.4.1.6296.101.56.3.2.18
Use this command to enable/disable the BFD check on interface. 1 : enable 0 : disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfControlCircuitType 1.3.6.1.4.1.6296.101.56.3.2.19
Use this command to set the circuit type for the interface. 1 : level-1 2 : level-1-2,(default) 3 : level-2
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), level1(1), level1To2(2), level2(3)  

sleISISIfControlCsnpIntervalLevel1 1.3.6.1.4.1.6296.101.56.3.2.20
Use this command to set CSNP (Complete sequence number PDU) interval in seconds. range : 1 ? 65535 default : 10
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

sleISISIfControlCsnpIntervalLevel2 1.3.6.1.4.1.6296.101.56.3.2.21
Use this command to set CSNP (Complete sequence number PDU) interval in seconds. range : 1 ? 65535 default : 10
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

sleISISIfControlHelloPadding 1.3.6.1.4.1.6296.101.56.3.2.22
Use this command to configure the padding of the ISIS Hello packet. 1 : enable 0 : disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfControlHelloIntervalLevel1 1.3.6.1.4.1.6296.101.56.3.2.23
Use this command to set the Hello interval in seconds. range : 1 ? 65535 default : 10
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

sleISISIfControlHelloIntervalLevel2 1.3.6.1.4.1.6296.101.56.3.2.24
Use this command to set the Hello interval in seconds. range : 1 ? 65535 default : 10
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

sleISISIfControlHelloIntervalMinimalLevel1 1.3.6.1.4.1.6296.101.56.3.2.25
Use this command to set the Hello interval in seconds. 1 : enable 0 : disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfControlHelloIntervalMinimalLevel2 1.3.6.1.4.1.6296.101.56.3.2.26
Use this command to set the Hello interval in seconds. 1 : enable 0 : disable
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), enable(1)  

sleISISIfControlHelloMultiplierLevel1 1.3.6.1.4.1.6296.101.56.3.2.27
Use this command to set multiplier for Hello holding time. range : 2 ? 10 default : 3
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..10  

sleISISIfControlHelloMultiplierLevel2 1.3.6.1.4.1.6296.101.56.3.2.28
Use this command to set multiplier for Hello holding time. range : 2 ? 10 default : 3
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 2..10  

sleISISIfControlLspInterval 1.3.6.1.4.1.6296.101.56.3.2.29
Use this command to set the Link State Packet (LSP) transmission interval. range : 1 ? 4294967295 default : 33
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 2..4294967295  

sleISISIfControlMeshGroup 1.3.6.1.4.1.6296.101.56.3.2.30
Use this command to set Mesh Group ID on the current interface. range : 1 ? 4294967295 disable : 0
Status: current Access: read-write
OBJECT-TYPE    
  Unsigned32 0 | 1..4294967295  

sleISISIfControlMetricLevel1 1.3.6.1.4.1.6296.101.56.3.2.31
Use this command to set default metric for the interface. range : 1 ? 63 default : 10
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..63  

sleISISIfControlMetricLevel2 1.3.6.1.4.1.6296.101.56.3.2.32
Use this command to set default metric for the interface. range : 1 ? 63 default : 10
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..63  

sleISISIfControlNetwork 1.3.6.1.4.1.6296.101.56.3.2.33
Use this command to change a broadcast interface network type to a point-to-point network type. 0 : disable 1 : broadcast 2 : point-to-point
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER disable(0), broadcast(1), pointToPoint(2)  

sleISISIfControlPriorityLevel1 1.3.6.1.4.1.6296.101.56.3.2.34
Use this command to set the priority for LAN DIS election. range : 0 ? 127 default : 64
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..127  

sleISISIfControlPriorityLevel2 1.3.6.1.4.1.6296.101.56.3.2.35
Use this command to set the priority for LAN DIS election. range : 0 ? 127 default : 64
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..127  

sleISISIfControlRestartHelloIntervalLevel1 1.3.6.1.4.1.6296.101.56.3.2.36
Use this command to configure the T1 timer, interval of ISIS Hello packet with restart TLV. range : 1 ? 65535 default : 3
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

sleISISIfControlRestartHelloIntervalLevel2 1.3.6.1.4.1.6296.101.56.3.2.37
Use this command to configure the T1 timer, interval of ISIS Hello packet with restart TLV. range : 1 ? 65535 default : 3
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..65535  

sleISISIfControlRetransmitInterval 1.3.6.1.4.1.6296.101.56.3.2.38
Use this command to set LSP retransmission interval. range : 0 ? 65535 default : 5
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..65535  

sleISISIfControlWideMetricLevel1 1.3.6.1.4.1.6296.101.56.3.2.39
Use this command to set wide metric for the interface. range : 1 - 16777214 default : 10
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..16777214  

sleISISIfControlWideMetricLevel2 1.3.6.1.4.1.6296.101.56.3.2.40
Use this command to set wide metric for the interface. range : 1 - 16777214 default : 10
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..16777214  

slsISISNotification 1.3.6.1.4.1.6296.101.56.3.3
OBJECT IDENTIFIER    

sleISISIfStatusTable 1.3.6.1.4.1.6296.101.56.3.4
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SleISISIfStatusEntry

sleISISIfStatusEntry 1.3.6.1.4.1.6296.101.56.3.4.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SleISISIfStatusEntry  

sleISISIfStatusIfIndex 1.3.6.1.4.1.6296.101.56.3.4.1.1
vlan interface index for isis protocol.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

sleIsisIfStatusIfStatus 1.3.6.1.4.1.6296.101.56.3.4.1.2
The interface up/down status
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER down(0), up(1)  

sleIsisIfStatusIsisTag 1.3.6.1.4.1.6296.101.56.3.4.1.3
The ISIS tag
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleIsisIfStatusNetworkType 1.3.6.1.4.1.6296.101.56.3.4.1.4
The network type
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), broadcast(1), point2Point(2), loopback(3)  

sleIsisIfStatusCircuitType 1.3.6.1.4.1.6296.101.56.3.4.1.5
The circuit type
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), level1(1), level2(2), level1And2(3)  

sleIsisIfStatusLocalCircuitId 1.3.6.1.4.1.6296.101.56.3.4.1.6
The local circuit id
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleIsisIfStatusExtendedLocalCircuitId 1.3.6.1.4.1.6296.101.56.3.4.1.7
The extended local circuit id
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleIsisIfStatusLocalSnpa 1.3.6.1.4.1.6296.101.56.3.4.1.8
The local SNPA mac address
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleIsisIfStatusLdpSyncHoldTimer 1.3.6.1.4.1.6296.101.56.3.4.1.9
The LDP sync hold timer(sec)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleIsisIfStatusLdpSyncRemainingTime 1.3.6.1.4.1.6296.101.56.3.4.1.10
The LDP sync remaining time(sec)
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleIsisIfStatusCircuitL1Metric 1.3.6.1.4.1.6296.101.56.3.4.1.11
The narrow metric of level1
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleIsisIfStatusCircuitL1WideMetric 1.3.6.1.4.1.6296.101.56.3.4.1.12
The wide metric of level1
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleIsisIfStatusCircuitL1Priority 1.3.6.1.4.1.6296.101.56.3.4.1.13
The priority of level1
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleIsisIfStatusCircuitL1CircuitId 1.3.6.1.4.1.6296.101.56.3.4.1.14
The circuit id of level1
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleIsisIfStatusCircuitL1ActiveAdjacencies 1.3.6.1.4.1.6296.101.56.3.4.1.15
The active adjacencies of level1
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleIsisIfStatusCircuitL1LscpMtu 1.3.6.1.4.1.6296.101.56.3.4.1.16
The MTU of level1
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleIsisIfStatusCircuitL2Metric 1.3.6.1.4.1.6296.101.56.3.4.1.17
The narrow metric of level2
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleIsisIfStatusCircuitL2WideMetric 1.3.6.1.4.1.6296.101.56.3.4.1.18
The wide metric of level2
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleIsisIfStatusCircuitL2Priority 1.3.6.1.4.1.6296.101.56.3.4.1.19
The priority of level2
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleIsisIfStatusCircuitL2CircuitId 1.3.6.1.4.1.6296.101.56.3.4.1.20
The circuit id of level2
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleIsisIfStatusCircuitL2ActiveAdjacencies 1.3.6.1.4.1.6296.101.56.3.4.1.21
The active adjacencies of level2
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleIsisIfStatusCircuitL2LscpMtu 1.3.6.1.4.1.6296.101.56.3.4.1.22
The MTU of level2
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleIsisIfStatusL1HelloTimerBroadcast 1.3.6.1.4.1.6296.101.56.3.4.1.23
The Level1 hello timer of broadcast
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleIsisIfStatusL2HelloTimerBroadcast 1.3.6.1.4.1.6296.101.56.3.4.1.24
The Level2 hello timer of broadcast
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleIsisIfStatusL1HellotimerPoint2Point 1.3.6.1.4.1.6296.101.56.3.4.1.25
The Level1 hello timer of porint to point
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleIsisIfStatusL2HellotimerPoint2Point 1.3.6.1.4.1.6296.101.56.3.4.1.26
The Level2 hello timer of porint to point
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISInstIf 1.3.6.1.4.1.6296.101.56.4
OBJECT IDENTIFIER    

sleISISInstIfTable 1.3.6.1.4.1.6296.101.56.4.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SleISISInstIfEntry

sleISISInstIfEntry 1.3.6.1.4.1.6296.101.56.4.1.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SleISISInstIfEntry  

sleISISInstIfInstanceId 1.3.6.1.4.1.6296.101.56.4.1.1.1
The ISIS instance index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

sleISISInstIfInterfaceId 1.3.6.1.4.1.6296.101.56.4.1.1.2
The ISIS interface index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

sleISISPassiveInterface 1.3.6.1.4.1.6296.101.56.4.1.1.3
The passive interface configuration.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), enable(1)  

sleISISInstIfControl 1.3.6.1.4.1.6296.101.56.4.2
OBJECT IDENTIFIER    

sleISISInstIfControlRequest 1.3.6.1.4.1.6296.101.56.4.2.1
The request of a user command
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER setISISInstIfPassiveIf(1), delISISInstIfPassiveIf(2)  

sleISISInstIfControlStatus 1.3.6.1.4.1.6296.101.56.4.2.2
Description.
Status: current Access: read-only
OBJECT-TYPE    
  SleControlStatusType  

sleISISInstIfControlTimer 1.3.6.1.4.1.6296.101.56.4.2.3
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Gauge32  

sleISISInstIfControlTimeStamp 1.3.6.1.4.1.6296.101.56.4.2.4
Description.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

sleISISInstIfControlReqResult 1.3.6.1.4.1.6296.101.56.4.2.5
Description.
Status: current Access: read-only
OBJECT-TYPE    
  SleControlRequestResultType  

sleISISInstIfControlInstanceId 1.3.6.1.4.1.6296.101.56.4.2.6
The ISIS instance index
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sleISISInstIfControlInterfaceId 1.3.6.1.4.1.6296.101.56.4.2.7
The ISIS interface index ( 0 means all interface)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sleISISInstRedistribute 1.3.6.1.4.1.6296.101.56.5
OBJECT IDENTIFIER    

sleISISInstRedistProtocol 1.3.6.1.4.1.6296.101.56.5.1
OBJECT IDENTIFIER    

sleISISInstRedistProtocolTable 1.3.6.1.4.1.6296.101.56.5.1.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SleISISInstRedistProtocolEntry

sleISISInstRedistProtocolEntry 1.3.6.1.4.1.6296.101.56.5.1.1.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SleISISInstRedistProtocolEntry  

sleISISInstRedistProtocolInstanceId 1.3.6.1.4.1.6296.101.56.5.1.1.1.1
The ISIS instance index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

sleISISInstRedistProtocolId 1.3.6.1.4.1.6296.101.56.5.1.1.1.2
The ISIS instance index
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER kernel(1), connected(2), static(3), rip(4), ospf(5), bgp(6)  

sleISISInstRedistProtocolMetric 1.3.6.1.4.1.6296.101.56.5.1.1.1.3
The ISIS interface index
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..4261412864  

sleISISInstRedistProtocolMetricType 1.3.6.1.4.1.6296.101.56.5.1.1.1.4
The passive interface configuration.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(-1), internal(0), external(1)  

sleISISInstRedistProtocolRouteLevelType 1.3.6.1.4.1.6296.101.56.5.1.1.1.5
The passive interface configuration.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), level1(1), level2(2), level1To2(3)  

sleISISInstRedistProtocolRouteMapName 1.3.6.1.4.1.6296.101.56.5.1.1.1.6
The passive interface configuration.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISInstRedistProtocolControl 1.3.6.1.4.1.6296.101.56.5.1.2
OBJECT IDENTIFIER    

sleISISInstRedistProtocolControlRequest 1.3.6.1.4.1.6296.101.56.5.1.2.1
The request of a user command
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER setISISInstIfRedistProtocol(1), delISISInstIfRedistProtocol(2)  

sleISISInstRedistProtocolControlStatus 1.3.6.1.4.1.6296.101.56.5.1.2.2
Description.
Status: current Access: read-only
OBJECT-TYPE    
  SleControlStatusType  

sleISISInstRedistProtocolControlTimer 1.3.6.1.4.1.6296.101.56.5.1.2.3
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Gauge32  

sleISISInstRedistProtocolControlTimeStamp 1.3.6.1.4.1.6296.101.56.5.1.2.4
Description.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

sleISISInstRedistProtocolControlReqResult 1.3.6.1.4.1.6296.101.56.5.1.2.5
Description.
Status: current Access: read-only
OBJECT-TYPE    
  SleControlRequestResultType  

sleISISInstRedistProtocolControlInstanceId 1.3.6.1.4.1.6296.101.56.5.1.2.6
The ISIS instance index
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sleISISInstRedistProtocolControlId 1.3.6.1.4.1.6296.101.56.5.1.2.7
The ISIS interface index ( 0 means all interface)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER kernel(1), connected(2), static(3), rip(4), ospf(5), bgp(6)  

sleISISInstRedistProtocolControlMetric 1.3.6.1.4.1.6296.101.56.5.1.2.8
The ISIS interface index ( 0 means all interface)
Status: current Access: read-write
OBJECT-TYPE    
  Gauge32 0..4261412864  

sleISISInstRedistProtocolControlMetricType 1.3.6.1.4.1.6296.101.56.5.1.2.9
The ISIS interface index ( 0 means all interface)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(-1), internal(0), external(1)  

sleISISInstRedistProtocolControlRouteLevelType 1.3.6.1.4.1.6296.101.56.5.1.2.10
The ISIS interface index ( 0 means all interface)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), level1(1), level2(2), level1To2(3)  

sleISISInstRedistProtocolControlRouteMapName 1.3.6.1.4.1.6296.101.56.5.1.2.11
The ISIS interface index ( 0 means all interface)
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

sleISISInstRedistIsisProtocol 1.3.6.1.4.1.6296.101.56.5.2
OBJECT IDENTIFIER    

sleISISInstRedistIsisProtocolTable 1.3.6.1.4.1.6296.101.56.5.2.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SleISISInstRedistIsisProtocolEntry

sleISISInstRedistIsisProtocolEntry 1.3.6.1.4.1.6296.101.56.5.2.1.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SleISISInstRedistIsisProtocolEntry  

sleISISInstRedistIsisProtocolInstanceId 1.3.6.1.4.1.6296.101.56.5.2.1.1.1
The ISIS instance index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

sleISISInstRedistIsisProtocolInterAreaFromLv1ToLv2 1.3.6.1.4.1.6296.101.56.5.2.1.1.2
The ISIS instance index
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), enable(1)  

sleISISInstRedistIsisProtocolLv1Lv2DistributeList 1.3.6.1.4.1.6296.101.56.5.2.1.1.3
The ISIS interface index
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISInstRedistIsisProtocolInterAreaFromLv2ToLv1 1.3.6.1.4.1.6296.101.56.5.2.1.1.4
The passive interface configuration.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), enable(1)  

sleISISInstRedistIsisProtocolLv2Lv1DistributeList 1.3.6.1.4.1.6296.101.56.5.2.1.1.5
The passive interface configuration.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISInstRedistIsisProtocolControl 1.3.6.1.4.1.6296.101.56.5.2.2
OBJECT IDENTIFIER    

sleISISInstRedistIsisProtocolControlRequest 1.3.6.1.4.1.6296.101.56.5.2.2.1
The request of a user command
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER setISISInstRedistIsisLv1Lv2(1), delISISInstRedistIsisLv1Lv2(2), setISISInstRedistIsisLv2Lv1(3), delISISInstRedistIsisLv2Lv1(4)  

sleISISInstRedistIsisProtocolControlStatus 1.3.6.1.4.1.6296.101.56.5.2.2.2
Description.
Status: current Access: read-only
OBJECT-TYPE    
  SleControlStatusType  

sleISISInstRedistIsisProtocolControlTimer 1.3.6.1.4.1.6296.101.56.5.2.2.3
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Gauge32  

sleISISInstRedistIsisProtocolControlTimeStamp 1.3.6.1.4.1.6296.101.56.5.2.2.4
Description.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

sleISISInstRedistIsisProtocolControlReqResult 1.3.6.1.4.1.6296.101.56.5.2.2.5
Description.
Status: current Access: read-only
OBJECT-TYPE    
  SleControlRequestResultType  

sleISISInstRedistIsisProtocolControlInstanceId 1.3.6.1.4.1.6296.101.56.5.2.2.6
The ISIS instance index
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sleISISInstRedistIsisProtocolControlLv1Lv2DistributeList 1.3.6.1.4.1.6296.101.56.5.2.2.7
The ISIS interface index ( 0 means all interface)
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

sleISISInstRedistIsisProtocolControlLv2Lv1DistributeList 1.3.6.1.4.1.6296.101.56.5.2.2.8
The ISIS interface index ( 0 means all interface)
Status: current Access: read-write
OBJECT-TYPE    
  OCTET STRING  

sleISISSummanryAddress 1.3.6.1.4.1.6296.101.56.6
OBJECT IDENTIFIER    

sleISISSummanryAddressTable 1.3.6.1.4.1.6296.101.56.6.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SleISISSummanryAddressEntry

sleISISSummanryAddressEntry 1.3.6.1.4.1.6296.101.56.6.1.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SleISISSummanryAddressEntry  

sleISISSummanryAddressInstanceId 1.3.6.1.4.1.6296.101.56.6.1.1.1
The ISIS instance index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..65535  

sleISISSummanryAddressIpValue 1.3.6.1.4.1.6296.101.56.6.1.1.2
The ISIS interface index
Status: current Access: read-only
OBJECT-TYPE    
  IpAddress  

sleISISSummanryAddressIpNetmask 1.3.6.1.4.1.6296.101.56.6.1.1.3
The passive interface configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..32  

sleISISSummanryAddressLevel 1.3.6.1.4.1.6296.101.56.6.1.1.4
The passive interface configuration.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER none(0), level1(1), level2(2), level1To2(3)  

sleISISSummanryAddressMetric 1.3.6.1.4.1.6296.101.56.6.1.1.5
The passive interface configuration.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..63  

sleISISSummanryAddressControl 1.3.6.1.4.1.6296.101.56.6.2
OBJECT IDENTIFIER    

sleISISSummanryAddressControlRequest 1.3.6.1.4.1.6296.101.56.6.2.1
The request of a user command
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER setISISSummaryAddress(1), delISISSummaryAddress(2)  

sleISISSummanryAddressControlStatus 1.3.6.1.4.1.6296.101.56.6.2.2
Description.
Status: current Access: read-only
OBJECT-TYPE    
  SleControlStatusType  

sleISISSummanryAddressControlTimer 1.3.6.1.4.1.6296.101.56.6.2.3
Description.
Status: current Access: read-write
OBJECT-TYPE    
  Gauge32  

sleISISSummanryAddressControlTimeStamp 1.3.6.1.4.1.6296.101.56.6.2.4
Description.
Status: current Access: read-only
OBJECT-TYPE    
  TimeTicks  

sleISISSummanryAddressControlReqResult 1.3.6.1.4.1.6296.101.56.6.2.5
Description.
Status: current Access: read-only
OBJECT-TYPE    
  SleControlRequestResultType  

sleISISSummanryAddressControlInstanceId 1.3.6.1.4.1.6296.101.56.6.2.6
The ISIS instance index
Status: current Access: read-write
OBJECT-TYPE    
  Integer32  

sleISISSummanryAddressControlIpValue 1.3.6.1.4.1.6296.101.56.6.2.7
The ISIS interface index ( 0 means all interface)
Status: current Access: read-write
OBJECT-TYPE    
  IpAddress  

sleISISSummanryAddressControlIpNetmask 1.3.6.1.4.1.6296.101.56.6.2.8
The ISIS interface index ( 0 means all interface)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 0..32  

sleISISSummanryAddressControlLevel 1.3.6.1.4.1.6296.101.56.6.2.9
The ISIS interface index ( 0 means all interface)
Status: current Access: read-write
OBJECT-TYPE    
  INTEGER none(0), level1(1), level2(2), level1To2(3)  

sleISISSummanryAddressControlMetric 1.3.6.1.4.1.6296.101.56.6.2.10
The ISIS interface index ( 0 means all interface)
Status: current Access: read-write
OBJECT-TYPE    
  Integer32 1..63  

sleISISDatabase 1.3.6.1.4.1.6296.101.56.7
OBJECT IDENTIFIER    

sleISISDatabaseTable 1.3.6.1.4.1.6296.101.56.7.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SleISISDatabaseEntry

sleISISDatabaseEntry 1.3.6.1.4.1.6296.101.56.7.1.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SleISISDatabaseEntry  

sleISISDatabaseTag 1.3.6.1.4.1.6296.101.56.7.1.1.1
ISIS database tag ID
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISDatabaseLevel 1.3.6.1.4.1.6296.101.56.7.1.1.2
ISIS database level index
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 1..2  

sleISISDatabaseLspId 1.3.6.1.4.1.6296.101.56.7.1.1.3
ISIS database lsp ID
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISDatabaseLspSeqNum 1.3.6.1.4.1.6296.101.56.7.1.1.4
ISIS database lsp sequence number
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISDatabaseLspChecksum 1.3.6.1.4.1.6296.101.56.7.1.1.5
ISIS database lsp Checksum
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISDatabaseLspHoldtime 1.3.6.1.4.1.6296.101.56.7.1.1.6
ISIS database lsp Holdtime
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISDatabaseAtt 1.3.6.1.4.1.6296.101.56.7.1.1.7
ISIS database att
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleISISDatabaseP 1.3.6.1.4.1.6296.101.56.7.1.1.8
ISIS database partition
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleISISDatabaseOl 1.3.6.1.4.1.6296.101.56.7.1.1.9
ISIS database overload
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleISISDatabaseDetail 1.3.6.1.4.1.6296.101.56.8
OBJECT IDENTIFIER    

sleISISDatabaseDetailTable 1.3.6.1.4.1.6296.101.56.8.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SleISISDatabaseDetailEntry

sleISISDatabaseDetailEntry 1.3.6.1.4.1.6296.101.56.8.1.1
Description.
Status: current Access: not-accessible
OBJECT-TYPE    
  SleISISDatabaseDetailEntry  

sleISISDatabaseDetailTag 1.3.6.1.4.1.6296.101.56.8.1.1.1
ISIS database tag
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISDatabaseDetailLevel 1.3.6.1.4.1.6296.101.56.8.1.1.2
ISIS database level
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER null(0), level1(1), level2(2)  

sleISISDatabaseDetailLspId 1.3.6.1.4.1.6296.101.56.8.1.1.3
ISIS database lsp id
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISDatabaseDetailType 1.3.6.1.4.1.6296.101.56.8.1.1.4
ISIS database lsp detail type.
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER areaAddr(1), lspIsNeighbor(2), lspEsNeighbor(3), authInfo(10), extendedIsReachability(22), ipInternalReachability(128), protocolsSupportded(129), ipExternalReachability(130), ipIfAddr(132), ipAuthInfo(133), teRouteId(134), extendedIpReachability(135), hostname(137), sharedRiskLinkGroup(138), multiIsReachability(222), multiTopology(229), ipv6IfAddr(232), multiIpv4Reachability(235), ipv6Reachability(236), multiIpv6Reachability(237)  

sleISISDatabaseDetailIndex 1.3.6.1.4.1.6296.101.56.8.1.1.5
ISIS database detail index.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32 0..65535  

sleISISDatabaseDetailPad 1.3.6.1.4.1.6296.101.56.8.1.1.6
ISIS database lsp detail pad.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISDatabaseDetailValue 1.3.6.1.4.1.6296.101.56.8.1.1.7
ISIS database lsp detail vlaue.
Status: current Access: read-only
OBJECT-TYPE    
  Integer32  

sleISISDatabaseDetailDescription 1.3.6.1.4.1.6296.101.56.8.1.1.8
ISIS database detail description.
Status: current Access: read-only
OBJECT-TYPE    
  OCTET STRING  

sleISISGroup 1.3.6.1.4.1.6296.101.56.9
Description.
Status: current Access: read-only
OBJECT-GROUP    

Generation date: July 28, 2023, 16:18:13, Copyright © 2007 - 2022 - Circitor