SL-SONET-SUP-PM-MIB

File: SL-SONET-SUP-PM-MIB.mib (93181 bytes)

Imported modules

SNMPv2-SMI	SNMPv2-TC	SNMPv2-CONF
PerfHist-TC-MIB	SONET-MIB	IF-MIB
SL-SONET-MIB

Imported symbols

MODULE-IDENTITY	OBJECT-TYPE	NOTIFICATION-TYPE
Integer32	transmission	Gauge32
TruthValue	DateAndTime	OBJECT-GROUP
NOTIFICATION-GROUP	MODULE-COMPLIANCE	PerfCurrentCount
PerfIntervalCount	PerfTotalCount	sonetMediumEntry
sonetSectionCurrentEntry	sonetSectionIntervalEntry	sonetLineCurrentEntry
sonetLineIntervalEntry	sonetFarEndLineCurrentEntry	sonetFarEndLineIntervalEntry
sonetPathCurrentEntry	sonetPathIntervalEntry	sonetFarEndPathCurrentEntry
sonetFarEndPathIntervalEntry	sonetVTCurrentEntry	sonetVTIntervalEntry
sonetFarEndVTCurrentEntry	sonetFarEndVTIntervalEntry	ifIndex
slSonetMib

Defined Types

SonetSectionDefaultThresholdEntry
SEQUENCE
	sonetSectionDefaultThresholdRate	INTEGER
	sonetSectionDefaultCVThreshold	INTEGER
	sonetSectionDefaultESThreshold	INTEGER
	sonetSectionDefaultSESThreshold	INTEGER
	sonetSectionDefaultSEFSThreshold	INTEGER
	sonetSectionDefaultDayCVThreshold	INTEGER
	sonetSectionDefaultDayESThreshold	INTEGER
	sonetSectionDefaultDaySESThreshold	INTEGER
	sonetSectionDefaultDaySEFSThreshold	INTEGER

SonetSectionThresholdEntry
SEQUENCE
	sonetSectionCurrentCVThreshold	INTEGER
	sonetSectionCurrentESThreshold	INTEGER
	sonetSectionCurrentSESThreshold	INTEGER
	sonetSectionCurrentSEFSThreshold	INTEGER
	sonetSectionDayCVThreshold	INTEGER
	sonetSectionDayESThreshold	INTEGER
	sonetSectionDaySESThreshold	INTEGER
	sonetSectionDaySEFSThreshold	INTEGER

SonetSectionDayEntry
SEQUENCE
	sonetSectionDayNumber	INTEGER
	sonetSectionDayStartTime	DateAndTime
	sonetSectionDayValidData	TruthValue
	sonetSectionDayCVs	PerfTotalCount
	sonetSectionDayESs	PerfTotalCount
	sonetSectionDaySESs	PerfTotalCount
	sonetSectionDaySEFSs	PerfTotalCount
	sonetSectionDayTcaFlag	TruthValue
	sonetSectionDayReset	INTEGER

SonetLineDefaultThresholdEntry
SEQUENCE
	sonetLineDefaultThresholdDirection	INTEGER
	sonetLineDefaultThresholdRate	INTEGER
	sonetLineDefaultCVThreshold	INTEGER
	sonetLineDefaultESThreshold	INTEGER
	sonetLineDefaultSESThreshold	INTEGER
	sonetLineDefaultUASThreshold	INTEGER
	sonetLineDefaultDayCVThreshold	INTEGER
	sonetLineDefaultDayESThreshold	INTEGER
	sonetLineDefaultDaySESThreshold	INTEGER
	sonetLineDefaultDayUASThreshold	INTEGER

SonetLineThresholdEntry
SEQUENCE
	sonetLineThresholdDirection	INTEGER
	sonetLineCurrentCVThreshold	INTEGER
	sonetLineCurrentESThreshold	INTEGER
	sonetLineCurrentSESThreshold	INTEGER
	sonetLineCurrentUASThreshold	INTEGER
	sonetLineDayCVThreshold	INTEGER
	sonetLineDayESThreshold	INTEGER
	sonetLineDaySESThreshold	INTEGER
	sonetLineDayUASThreshold	INTEGER

SonetLineDayEntry
SEQUENCE
	sonetLineDayNumber	INTEGER
	sonetLineDayStartTime	DateAndTime
	sonetLineDayValidData	TruthValue
	sonetLineDayCVs	PerfTotalCount
	sonetLineDayESs	PerfTotalCount
	sonetLineDaySESs	PerfTotalCount
	sonetLineDayUASs	PerfTotalCount
	sonetLineDayPSC	PerfTotalCount
	sonetLineDayPSD	PerfTotalCount
	sonetLineDayFCs	PerfTotalCount
	sonetLineDayTcaFlag	TruthValue
	sonetLineDayReset	INTEGER

SonetFarEndLineDayEntry
SEQUENCE
	sonetFarEndLineDayNumber	INTEGER
	sonetFarEndLineDayStartTime	DateAndTime
	sonetFarEndLineDayValidData	TruthValue
	sonetFarEndLineDayCVs	PerfTotalCount
	sonetFarEndLineDayESs	PerfTotalCount
	sonetFarEndLineDaySESs	PerfTotalCount
	sonetFarEndLineDayUASs	PerfTotalCount
	sonetFarEndLineDayFCs	PerfTotalCount
	sonetFarEndLineDayTcaFlag	TruthValue
	sonetFarEndLineDayReset	INTEGER

SonetPathDefaultThresholdEntry
SEQUENCE
	sonetPathDefaultThresholdDirection	INTEGER
	sonetPathDefaultThresholdRate	INTEGER
	sonetPathDefaultCVThreshold	INTEGER
	sonetPathDefaultESThreshold	INTEGER
	sonetPathDefaultSESThreshold	INTEGER
	sonetPathDefaultUASThreshold	INTEGER
	sonetPathDefaultDayCVThreshold	INTEGER
	sonetPathDefaultDayESThreshold	INTEGER
	sonetPathDefaultDaySESThreshold	INTEGER
	sonetPathDefaultDayUASThreshold	INTEGER

SonetPathThresholdEntry
SEQUENCE
	sonetPathThresholdDirection	INTEGER
	sonetPathCurrentCVThreshold	INTEGER
	sonetPathCurrentESThreshold	INTEGER
	sonetPathCurrentSESThreshold	INTEGER
	sonetPathCurrentUASThreshold	INTEGER
	sonetPathDayCVThreshold	INTEGER
	sonetPathDayESThreshold	INTEGER
	sonetPathDaySESThreshold	INTEGER
	sonetPathDayUASThreshold	INTEGER

SonetPathDayEntry
SEQUENCE
	sonetPathDayNumber	INTEGER
	sonetPathDayStartTime	DateAndTime
	sonetPathDayValidData	TruthValue
	sonetPathDayCVs	PerfTotalCount
	sonetPathDayESs	PerfTotalCount
	sonetPathDaySESs	PerfTotalCount
	sonetPathDayUASs	PerfTotalCount
	sonetPathDayFCs	PerfTotalCount
	sonetPathDayTcaFlag	TruthValue
	sonetPathDayEBs	PerfTotalCount
	sonetPathDayReset	INTEGER

SonetFarEndPathDayEntry
SEQUENCE
	sonetFarEndPathDayNumber	INTEGER
	sonetFarEndPathDayStartTime	DateAndTime
	sonetFarEndPathDayValidData	TruthValue
	sonetFarEndPathDayCVs	PerfTotalCount
	sonetFarEndPathDayESs	PerfTotalCount
	sonetFarEndPathDaySESs	PerfTotalCount
	sonetFarEndPathDayUASs	PerfTotalCount
	sonetFarEndPathDayFCs	PerfTotalCount
	sonetFarEndPathDayTcaFlag	TruthValue
	sonetFarEndPathDayEBs	PerfTotalCount
	sonetFarEndPathDayReset	INTEGER

SonetVTDefaultThresholdEntry
SEQUENCE
	sonetVTDefaultThresholdDirection	INTEGER
	sonetVTDefaultThresholdRate	INTEGER
	sonetVTDefaultCVThreshold	INTEGER
	sonetVTDefaultESThreshold	INTEGER
	sonetVTDefaultSESThreshold	INTEGER
	sonetVTDefaultUASThreshold	INTEGER
	sonetVTDefaultDayCVThreshold	INTEGER
	sonetVTDefaultDayESThreshold	INTEGER
	sonetVTDefaultDaySESThreshold	INTEGER
	sonetVTDefaultDayUASThreshold	INTEGER

SonetVTThresholdEntry
SEQUENCE
	sonetVTCurrentCVThreshold	INTEGER
	sonetVTCurrentESThreshold	INTEGER
	sonetVTCurrentSESThreshold	INTEGER
	sonetVTCurrentUASThreshold	INTEGER
	sonetVTDayCVThreshold	INTEGER
	sonetVTDayESThreshold	INTEGER
	sonetVTDaySESThreshold	INTEGER
	sonetVTDayUASThreshold	INTEGER

SonetVTDayEntry
SEQUENCE
	sonetVTDayNumber	INTEGER
	sonetVTDayStartTime	DateAndTime
	sonetVTDayValidData	TruthValue
	sonetVTDayFCs	PerfTotalCount
	sonetVTDayCVs	PerfTotalCount
	sonetVTDayESs	PerfTotalCount
	sonetVTDaySESs	PerfTotalCount
	sonetVTDayUASs	PerfTotalCount
	sonetVTDayEBs	PerfTotalCount
	sonetVTDayTcaFlag	TruthValue
	sonetVTDayReset	INTEGER

SonetFarEndVTDayEntry
SEQUENCE
	sonetFarEndVTDayNumber	INTEGER
	sonetFarEndVTDayStartTime	DateAndTime
	sonetFarEndVTDayValidData	TruthValue
	sonetFarEndVTDayFCs	PerfTotalCount
	sonetFarEndVTDayCVs	PerfTotalCount
	sonetFarEndVTDayESs	PerfTotalCount
	sonetFarEndVTDaySESs	PerfTotalCount
	sonetFarEndVTDayUASs	PerfTotalCount
	sonetFarEndVTDayEBs	PerfTotalCount
	sonetFarEndVTDayTcaFlag	TruthValue
	sonetFarEndVTDayReset	INTEGER

Defined Values

sonetSupPmMIB		1.3.6.1.4.1.4515.1.6.3
This MIB module provides extensions to the SONET-MIB (RFC 2558) objects. It provides definitions for management information that supports those parts of ANSI T1.231-1997 that are not covered by the SONET-MIB.
MODULE-IDENTITY

sonetSupObjects		1.3.6.1.4.1.4515.1.6.3.1
OBJECT IDENTIFIER

sonetSupObjectsPath		1.3.6.1.4.1.4515.1.6.3.2
OBJECT IDENTIFIER

sonetSupObjectsVT		1.3.6.1.4.1.4515.1.6.3.3
OBJECT IDENTIFIER

sonetSupConfig		1.3.6.1.4.1.4515.1.6.3.1.1
OBJECT IDENTIFIER

sonetSupMedium		1.3.6.1.4.1.4515.1.6.3.1.2
OBJECT IDENTIFIER

sonetSupSection		1.3.6.1.4.1.4515.1.6.3.1.3
OBJECT IDENTIFIER

sonetSupLine		1.3.6.1.4.1.4515.1.6.3.1.4
OBJECT IDENTIFIER

sonetSupFarEndLine		1.3.6.1.4.1.4515.1.6.3.1.5
OBJECT IDENTIFIER

sonetSupPath		1.3.6.1.4.1.4515.1.6.3.2.1
OBJECT IDENTIFIER

sonetSupFarEndPath		1.3.6.1.4.1.4515.1.6.3.2.2
OBJECT IDENTIFIER

sonetSupVT		1.3.6.1.4.1.4515.1.6.3.3.1
OBJECT IDENTIFIER

sonetSupFarEndVT		1.3.6.1.4.1.4515.1.6.3.3.2
OBJECT IDENTIFIER

sonetSectionDefaultThresholdTable		1.3.6.1.4.1.4515.1.6.3.1.3.1
The table of default thresholds for SONET section counters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SonetSectionDefaultThresholdEntry

sonetSectionDefaultThresholdEntry		1.3.6.1.4.1.4515.1.6.3.1.3.1.1
An entry in the table of default thresholds. The table has a variable for each counter type and accumulation period combination, but uses an index to indetify the digital signal rate. The agent must provide a set of default threshold values for all rates that the NE supports. The agent may make these variables read-only.
Status: current	Access: not-accessible
OBJECT-TYPE
	SonetSectionDefaultThresholdEntry

sonetSectionDefaultThresholdRate		1.3.6.1.4.1.4515.1.6.3.1.3.1.1.1
The digital signal rate for which the default threshold values apply.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	oc1(1), oc3(2), oc12(3), oc24(4), oc48(5), oc192(6)

sonetSectionDefaultCVThreshold		1.3.6.1.4.1.4515.1.6.3.1.3.1.1.2
The default value for SONET CV-S counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetSectionDefaultESThreshold		1.3.6.1.4.1.4515.1.6.3.1.3.1.1.3
The default value for SONET ES-S counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetSectionDefaultSESThreshold		1.3.6.1.4.1.4515.1.6.3.1.3.1.1.6
The default value for SONET SES-S counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetSectionDefaultSEFSThreshold		1.3.6.1.4.1.4515.1.6.3.1.3.1.1.7
The default value for SONET SEFS-S counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetSectionDefaultDayCVThreshold		1.3.6.1.4.1.4515.1.6.3.1.3.1.1.8
The default value for SONET CV-S counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetSectionDefaultDayESThreshold		1.3.6.1.4.1.4515.1.6.3.1.3.1.1.9
The default value for SONET ES-S counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetSectionDefaultDaySESThreshold		1.3.6.1.4.1.4515.1.6.3.1.3.1.1.12
The default value for SONET SES-S counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetSectionDefaultDaySEFSThreshold		1.3.6.1.4.1.4515.1.6.3.1.3.1.1.13
The default value for SONET SEFS-S counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetSectionThresholdTable		1.3.6.1.4.1.4515.1.6.3.1.3.2
The table of trap threshold values for SONET section counters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SonetSectionThresholdEntry

sonetSectionThresholdEntry		1.3.6.1.4.1.4515.1.6.3.1.3.2.1
An entry in the table of SONET Section trap thresholds.
Status: current	Access: not-accessible
OBJECT-TYPE
	SonetSectionThresholdEntry

sonetSectionCurrentCVThreshold		1.3.6.1.4.1.4515.1.6.3.1.3.2.1.1
The trap threshold value for the interface's current 15-minute interval CV-S counter. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetSectionCurrentESThreshold		1.3.6.1.4.1.4515.1.6.3.1.3.2.1.2
The trap threshold value for the interface's current 15-minute interval ES-S counter. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetSectionCurrentSESThreshold		1.3.6.1.4.1.4515.1.6.3.1.3.2.1.5
The trap threshold value for the interface's current 15-minute interval SES-S counter. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetSectionCurrentSEFSThreshold		1.3.6.1.4.1.4515.1.6.3.1.3.2.1.6
The trap threshold value for the interface's current 15-minute interval SEFS-S counter. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetSectionDayCVThreshold		1.3.6.1.4.1.4515.1.6.3.1.3.2.1.7
The trap threshold value for the interface's current day CV-S counter. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetSectionDayESThreshold		1.3.6.1.4.1.4515.1.6.3.1.3.2.1.8
The trap threshold value for the interface's current day ES-S counter. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetSectionDaySESThreshold		1.3.6.1.4.1.4515.1.6.3.1.3.2.1.11
The trap threshold value for the interface's current day SES-S counter. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetSectionDaySEFSThreshold		1.3.6.1.4.1.4515.1.6.3.1.3.2.1.12
The trap threshold value for the interface's current day SEFS-S counter. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetSectionDayTable		1.3.6.1.4.1.4515.1.6.3.1.3.15
The SONET Section Day table. Contains various statistics collected by each SONET Section over multiple 1-day intervals of operation.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SonetSectionDayEntry

sonetSectionDayEntry		1.3.6.1.4.1.4515.1.6.3.1.3.15.1
An entry in the SONET Section Day table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SonetSectionDayEntry

sonetSectionDayNumber		1.3.6.1.4.1.4515.1.6.3.1.3.15.1.1
A number which identifies the 1-day interval for which the set of section related statistics is available. The number is between 1 and n, where n is the number of 1-day intervals supported by the agent. The interval identified by 1 is the current 1-day interval, 2 is the previous (most recently completed) 1-day interval and n is the least recently completed 1-day interval. Interval 0 is used for the Untimed counters.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..33

sonetSectionDayStartTime		1.3.6.1.4.1.4515.1.6.3.1.3.15.1.2
This variable indicates the date and time at which this 1-day interval of sections measurements began on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

sonetSectionDayValidData		1.3.6.1.4.1.4515.1.6.3.1.3.15.1.3
This variable assumes the value true(1) if the data stored for this interval is both valid and complete. It is set to false(2) if the data stored for this interval is incomplete or otherwise invalid because (a) the data stored for this interval is for a period greater or less than 24 hours, or (b) some data is missing.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

sonetSectionDayCVs		1.3.6.1.4.1.4515.1.6.3.1.3.15.1.4
The section code violation (CV-S) count is the number of BIP-8 errors which were detected at the SONET section layer interface in a previous 1-day interval. Each section BIP-8 can detect up to eight errors per STS-N frame, with each error incrementing the CV counter. CVs for the section layer are collected using the BIP-8 in the B1 byte located in the section overhead of STS-1 number 1.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetSectionDayESs		1.3.6.1.4.1.4515.1.6.3.1.3.15.1.5
The section errored second (ES-S) count is the number of 1-second intervals containing one or more BIP-8 error (B1 byte), one or more SEF defects, or one or more LOS defects which were encountered by the SONET section layer interface in a previous 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetSectionDaySESs		1.3.6.1.4.1.4515.1.6.3.1.3.15.1.8
The section severely errored second (SES-S) count is the number of 1-second intervals containing sonetSevereErrorThreshold or more BIP-8 errors (B1 byte), one or more SEF defects, or one or more LOS defects which were encountered by the SONET section layer interface in a previous 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetSectionDaySEFSs		1.3.6.1.4.1.4515.1.6.3.1.3.15.1.9
The section severely errored frame second (SEFS-S) count is the number of 1-second intervals containing one or more SEF defects which were encountered by the SONET section layer interface in a previous 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetSectionDayTcaFlag		1.3.6.1.4.1.4515.1.6.3.1.3.15.1.10
TRUE if one of the counters crossed the threshold during the day.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

sonetSectionDayReset		1.3.6.1.4.1.4515.1.6.3.1.3.15.1.11
Writing this object reset the PM counters of this interval.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetLineDefaultThresholdTable		1.3.6.1.4.1.4515.1.6.3.1.4.1
The table of default thresholds for SONET Line counters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SonetLineDefaultThresholdEntry

sonetLineDefaultThresholdEntry		1.3.6.1.4.1.4515.1.6.3.1.4.1.1
An entry in the table of default thresholds. The table has a variable for each counter type and accumulation period combination, but uses indexes to indetify the digital signal direction and rate. The agent must provide a set of default threshold values for all rates that the NE supports. The agent may make these variables read-only.
Status: current	Access: not-accessible
OBJECT-TYPE
	SonetLineDefaultThresholdEntry

sonetLineDefaultThresholdDirection		1.3.6.1.4.1.4515.1.6.3.1.4.1.1.1
The digital signal direction for which the default threshold values apply.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	nearEnd(1), farEnd(2)

sonetLineDefaultThresholdRate		1.3.6.1.4.1.4515.1.6.3.1.4.1.1.2
The digital signal rate for which the default threshold values apply.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	vt1dot5(1), vtg(2), oc1(3), oc3(4), oc12(5), oc24(6), oc48(7), oc192(8)

sonetLineDefaultCVThreshold		1.3.6.1.4.1.4515.1.6.3.1.4.1.1.3
The default value for SONET CV-L and CV-LFE counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetLineDefaultESThreshold		1.3.6.1.4.1.4515.1.6.3.1.4.1.1.4
The default value for SONET ES-L and ES-LFE counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetLineDefaultSESThreshold		1.3.6.1.4.1.4515.1.6.3.1.4.1.1.7
The default value for SONET SES-L and SES-LFE counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetLineDefaultUASThreshold		1.3.6.1.4.1.4515.1.6.3.1.4.1.1.9
The default value for SONET UAS-L and UAS-LFE counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetLineDefaultDayCVThreshold		1.3.6.1.4.1.4515.1.6.3.1.4.1.1.10
The default value for SONET CV-L and CV-LFE counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetLineDefaultDayESThreshold		1.3.6.1.4.1.4515.1.6.3.1.4.1.1.11
The default value for SONET ES-L and ES-LFE counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetLineDefaultDaySESThreshold		1.3.6.1.4.1.4515.1.6.3.1.4.1.1.14
The default value for SONET SES-L and SES-LFE counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetLineDefaultDayUASThreshold		1.3.6.1.4.1.4515.1.6.3.1.4.1.1.16
The default value for SONET UAS-L and UAS-LFE counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetLineThresholdTable		1.3.6.1.4.1.4515.1.6.3.1.4.2
The table of trap threshold values for SONET Line counters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SonetLineThresholdEntry

sonetLineThresholdEntry		1.3.6.1.4.1.4515.1.6.3.1.4.2.1
An entry in the table of SONET Line trap thresholds.
Status: current	Access: not-accessible
OBJECT-TYPE
	SonetLineThresholdEntry

sonetLineThresholdDirection		1.3.6.1.4.1.4515.1.6.3.1.4.2.1.1
The digital signal direction for which the threshold values apply.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	nearEnd(1), farEnd(2)

sonetLineCurrentCVThreshold		1.3.6.1.4.1.4515.1.6.3.1.4.2.1.2
The trap threshold value for the interface's current 15-minute interval CV-L and CV-LFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetLineCurrentESThreshold		1.3.6.1.4.1.4515.1.6.3.1.4.2.1.3
The trap threshold value for the interface's current 15-minute interval ES-L and ES-LFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetLineCurrentSESThreshold		1.3.6.1.4.1.4515.1.6.3.1.4.2.1.4
The trap threshold value for the interface's current 15-minute interval SES-L and SES-LFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetLineCurrentUASThreshold		1.3.6.1.4.1.4515.1.6.3.1.4.2.1.5
The trap threshold value for the interface's current 15-minute interval UAS-L and UAS-LFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetLineDayCVThreshold		1.3.6.1.4.1.4515.1.6.3.1.4.2.1.6
The trap threshold value for the interface's current day CV-L and CV-LFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetLineDayESThreshold		1.3.6.1.4.1.4515.1.6.3.1.4.2.1.7
The trap threshold value for the interface's current day ES-L and ES-LFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetLineDaySESThreshold		1.3.6.1.4.1.4515.1.6.3.1.4.2.1.8
The trap threshold value for the interface's current day SES-L and SES-LFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

sonetLineDayUASThreshold		1.3.6.1.4.1.4515.1.6.3.1.4.2.1.9
The trap threshold value for the interface's current day UAS-L and UAS-LFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetLineDayTable		1.3.6.1.4.1.4515.1.6.3.1.4.5
The SONET Line Day table. Contains various statistics collected by each SONET line over multiple 1-day intervals of operation.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SonetLineDayEntry

sonetLineDayEntry		1.3.6.1.4.1.4515.1.6.3.1.4.5.1
An entry in the SONET Line Day table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SonetLineDayEntry

sonetLineDayNumber		1.3.6.1.4.1.4515.1.6.3.1.4.5.1.1
A number which identifies the 1-day interval for which the set of near-end line related statistics is available. The number is between 1 and n, where n is the number of 1-day intervals supported by the agent. The interval identified by 1 is the current 1-day interval, 2 is the previous (most recently completed) 1-day interval and n is the least recently completed 1-day interval. Interval 0 is used for the Untimed counters.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	0..33

sonetLineDayStartTime		1.3.6.1.4.1.4515.1.6.3.1.4.5.1.2
This variable indicates the date and time at which this 1-day interval of near-end line measurements began on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

sonetLineDayValidData		1.3.6.1.4.1.4515.1.6.3.1.4.5.1.3
This variable assumes the value true(1) if the data stored for this interval is both valid and complete. It is set to false(2) if the data stored for this interval is incomplete or otherwise invalid because (a) the data stored for this interval is for a period greater or less than 24 hours, or (b) some data is missing.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

sonetLineDayCVs		1.3.6.1.4.1.4515.1.6.3.1.4.5.1.5
The line code violation (CV-L) count is the number of BIP-8 errors which were detected at the SONET line layer interface in a previous 1-day interval. Each line BIP-8 can detect up to eight errors per STS-1 frame, with each error incrementing the CV counter. CVs for the line layer are collected using the BIP-8s in the B2 byte located in the line overhead of STS-1. (Since all CVs on an STS-N line are counted together, this is equivalent to counting each error in the BIP-8N contained in the B2 bytes of the STS-N line overhead.) Thus, on an STS-N signal, up to 8 x N CVs may occure in each STS-N frame.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetLineDayESs		1.3.6.1.4.1.4515.1.6.3.1.4.5.1.6
The line errored second (ES-L) count is the number of 1-second intervals containing one or more EDC error (B2 byte), or one or more AIS-L defects which were encountered by the SONET line layer interface in a previous 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetLineDaySESs		1.3.6.1.4.1.4515.1.6.3.1.4.5.1.9
The line severely errored second (SES-L) is a count of 1-second intervals containing sonetSevereErrorThreshold or more EDC errors (B2 byte) or one or more AIS-L defects which were encountered by the SONET line layer interface in a previous 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetLineDayUASs		1.3.6.1.4.1.4515.1.6.3.1.4.5.1.10
The line unavailable second (UAS-L) is a count of 1-second intervals for which the SONET line was unavailable during a previous 1-day interval. The SONET line becomes unavailable at the onset of 10 contiguous SES-Ls. The 10 SES-Ls are included in unavailable time. Once unavailable, the SONET line becomes available at the onset of 10 contiguous seconds with no SES-Ls. The 10 seconds with no SES-Ls are excluded from unavailable time.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetLineDayPSC		1.3.6.1.4.1.4515.1.6.3.1.4.5.1.11
The number of protection switching occured.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetLineDayPSD		1.3.6.1.4.1.4515.1.6.3.1.4.5.1.12
The length of time in seconds, where the protection unit was in service and the working unit was out of service, during the day.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetLineDayFCs		1.3.6.1.4.1.4515.1.6.3.1.4.5.1.13
The number of failure counts occured during the day.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetLineDayTcaFlag		1.3.6.1.4.1.4515.1.6.3.1.4.5.1.14
TRUE if one of the counters crossed the threshold during the day.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

sonetLineDayReset		1.3.6.1.4.1.4515.1.6.3.1.4.5.1.15
Writing this object reset the PM counters of this interval.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetFarEndLineDayTable		1.3.6.1.4.1.4515.1.6.3.1.5.3
The SONET Far End Line Day table. Contains various statistics collected by each SONET line over multiple 1-day intervals of operation.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SonetFarEndLineDayEntry

sonetFarEndLineDayEntry		1.3.6.1.4.1.4515.1.6.3.1.5.3.1
An entry in the SONET Far End Line Day table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SonetFarEndLineDayEntry

sonetFarEndLineDayNumber		1.3.6.1.4.1.4515.1.6.3.1.5.3.1.1
A number which identifies the 1-day interval for which the set of far-end line related statistics is available. The number is between 1 and n, where n is the number of 1-day intervals supported by the agent. The interval identified by 1 is the current 1-day interval, 2 is the previous (most recently completed) 1-day interval and n is the least recently completed 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..33

sonetFarEndLineDayStartTime		1.3.6.1.4.1.4515.1.6.3.1.5.3.1.2
This variable indicates the date and time at which this 1-day interval of far-end line measurements began on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

sonetFarEndLineDayValidData		1.3.6.1.4.1.4515.1.6.3.1.5.3.1.3
This variable assumes the value true(1) if the data stored for this interval is both valid and complete. It is set to false(2) if the data stored for this interval is incomplete or otherwise invalid because (a) the data stored for this interval is for a period greater or less than 24 hours, or (b) some data is missing (e.g., when a near-end defect prevents some far-end data from being collected).
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

sonetFarEndLineDayCVs		1.3.6.1.4.1.4515.1.6.3.1.5.3.1.5
The far-end line code violation (CV-LFE) count is the number of REI-Ls which were detected at the SONET line layer interface in a previous 1-day interval. For EC-1 or OC-1, REI-L is bits 5 to 8 of the M0 byte; for EC-N or OC-N (N>2), M1 byte.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetFarEndLineDayESs		1.3.6.1.4.1.4515.1.6.3.1.5.3.1.6
The far-end line errored second (ES-LFE) count is the number of 1-second intervals containing one or more REDC-Ls, or one or more RDI-L defects which were encountered by the SONET line layer interface in a previous 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetFarEndLineDaySESs		1.3.6.1.4.1.4515.1.6.3.1.5.3.1.9
The far-end line severely errored second (SES-LFE) is a count of 1-second intervals containing sonetSevereErrorThreshold or more REDC-Ls or one or more RDI-L defects which were detected by the SONET line layer interface in a previous 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetFarEndLineDayUASs		1.3.6.1.4.1.4515.1.6.3.1.5.3.1.10
The far-end line unavailable second (UAS-LFE) is a count of 1-second intervals for which the SONET line was unavailable during a previous 1-day interval. The SONET line becomes unavailable at the onset of 10 contiguous SES-LEFs. The 10 SES-LEFs are included in unavailable time. Once unavailable, the SONET line becomes available at the onset of 10 contiguous seconds with no SES-LEFs. The 10 seconds with no SES-LEFs are excluded from unavailable time.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetFarEndLineDayFCs		1.3.6.1.4.1.4515.1.6.3.1.5.3.1.11
The far-end line failures count.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetFarEndLineDayTcaFlag		1.3.6.1.4.1.4515.1.6.3.1.5.3.1.12
TRUE if one of the counters crossed the threshold during the day.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

sonetFarEndLineDayReset		1.3.6.1.4.1.4515.1.6.3.1.5.3.1.13
Writing this object reset the PM counters of this interval.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetPathDefaultThresholdTable		1.3.6.1.4.1.4515.1.6.3.2.1.1
The table of default thresholds for SONET Path counters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SonetPathDefaultThresholdEntry

sonetPathDefaultThresholdEntry		1.3.6.1.4.1.4515.1.6.3.2.1.1.1
An entry in the table of default thresholds. The table has a variable for each counter type and accumulation period combination, but uses indexes to indetify the digital signal direction and rate. The agent must provide a set of default threshold values for all rates that the NE supports. The agent may make these variables read-only.
Status: current	Access: not-accessible
OBJECT-TYPE
	SonetPathDefaultThresholdEntry

sonetPathDefaultThresholdDirection		1.3.6.1.4.1.4515.1.6.3.2.1.1.1.1
The digital signal direction for which the default threshold values apply.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	nearEnd(1), farEnd(2)

sonetPathDefaultThresholdRate		1.3.6.1.4.1.4515.1.6.3.2.1.1.1.2
The path digital signal rate for which the default threshold values apply.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	sts1(1), sts3(2), sts12(3), sts24(4), sts48(5), sts192(6)

sonetPathDefaultCVThreshold		1.3.6.1.4.1.4515.1.6.3.2.1.1.1.3
The default value for SONET CV-P and CV-PFE counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetPathDefaultESThreshold		1.3.6.1.4.1.4515.1.6.3.2.1.1.1.4
The default value for SONET ES-P and ES-PFE counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetPathDefaultSESThreshold		1.3.6.1.4.1.4515.1.6.3.2.1.1.1.7
The default value for SONET SES-P and SES-PFE counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetPathDefaultUASThreshold		1.3.6.1.4.1.4515.1.6.3.2.1.1.1.8
The default value for SONET UAS-P and UAS-PFE counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetPathDefaultDayCVThreshold		1.3.6.1.4.1.4515.1.6.3.2.1.1.1.16
The default value for SONET CV-P and CV-PFE counter 1-day interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetPathDefaultDayESThreshold		1.3.6.1.4.1.4515.1.6.3.2.1.1.1.17
The default value for SONET ES-P and ES-PFE counter 1-day interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetPathDefaultDaySESThreshold		1.3.6.1.4.1.4515.1.6.3.2.1.1.1.20
The default value for SONET SES-P and SES-PFE counter 1-day interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetPathDefaultDayUASThreshold		1.3.6.1.4.1.4515.1.6.3.2.1.1.1.21
The default value for SONET UAS-P and UAS-PFE counter 1-day interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetPathThresholdTable		1.3.6.1.4.1.4515.1.6.3.2.1.2
The table of trap threshold values for SONET Path counters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SonetPathThresholdEntry

sonetPathThresholdEntry		1.3.6.1.4.1.4515.1.6.3.2.1.2.1
An entry in the table of SONET Path trap thresholds.
Status: current	Access: not-accessible
OBJECT-TYPE
	SonetPathThresholdEntry

sonetPathThresholdDirection		1.3.6.1.4.1.4515.1.6.3.2.1.2.1.1
The digital signal direction for which the threshold values apply.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	nearEnd(1), farEnd(2)

sonetPathCurrentCVThreshold		1.3.6.1.4.1.4515.1.6.3.2.1.2.1.2
The trap threshold value for the interface's current 15-minute interval CV-P and CV-PFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetPathCurrentESThreshold		1.3.6.1.4.1.4515.1.6.3.2.1.2.1.3
The trap threshold value for the interface's current 15-minute interval ES-P and ES-PFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetPathCurrentSESThreshold		1.3.6.1.4.1.4515.1.6.3.2.1.2.1.4
The trap threshold value for the interface's current 15-minute interval SES-P and SES-PFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetPathCurrentUASThreshold		1.3.6.1.4.1.4515.1.6.3.2.1.2.1.5
The trap threshold value for the interface's current 15-minute interval UAS-P and UAS-PFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetPathDayCVThreshold		1.3.6.1.4.1.4515.1.6.3.2.1.2.1.6
The trap threshold value for the interface's current 1-day CV-P and CV-PFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetPathDayESThreshold		1.3.6.1.4.1.4515.1.6.3.2.1.2.1.7
The trap threshold value for the interface's current 1-day ES-P and ES-PFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetPathDaySESThreshold		1.3.6.1.4.1.4515.1.6.3.2.1.2.1.8
The trap threshold value for the interface's current 1-day SES-P and SES-PFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetPathDayUASThreshold		1.3.6.1.4.1.4515.1.6.3.2.1.2.1.9
The trap threshold value for the interface's current 1-day UAS-P and UAS-PFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetPathDayTable		1.3.6.1.4.1.4515.1.6.3.2.1.17
The SONET Path Day table. Contains performance statistics collected by each SONET Path over multiple 1-day intervals of operation.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SonetPathDayEntry

sonetPathDayEntry		1.3.6.1.4.1.4515.1.6.3.2.1.17.1
An entry in the SONET Path Day table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SonetPathDayEntry

sonetPathDayNumber		1.3.6.1.4.1.4515.1.6.3.2.1.17.1.1
A number which identifies the 1-day interval for which the set of near-end path related statistics is available. The number is between 1 and n, where n is the number of 1-day intervals supported by the agent. The interval identified by 1 is the current 1-day interval, 2 is the previous (most recently completed) 1-day interval and n is the least recently completed 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..33

sonetPathDayStartTime		1.3.6.1.4.1.4515.1.6.3.2.1.17.1.2
This variable indicates the date and time at which the 1-day interval of measurements began on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

sonetPathDayValidData		1.3.6.1.4.1.4515.1.6.3.2.1.17.1.3
This variable assumes the value true(1) if the data stored for this interval is both valid and complete. It is set to false(2) if the data stored for this interval is incomplete or otherwise invalid because (a) the data stored for this interval is for a period greater or less than 24 hours, or (b) some data is missing.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

sonetPathDayCVs		1.3.6.1.4.1.4515.1.6.3.2.1.17.1.5
The path code violation (CV-P) count is the number of BIP-8 errors which were detected at the STS-path layer interface in a previous 1-day interval. CVs for the path layer are collected using the BIP-8 in the B3 byte located in the STS-path overhead.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetPathDayESs		1.3.6.1.4.1.4515.1.6.3.2.1.17.1.6
The path errored second (ES-P) count is the number of 1-second intervals containing one or more EDC error (B3 byte), or one or more AIS-P, LOP-P, TIM-P or UNEQ-P defects which were encountered by the SONET path layer interface in a previous 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetPathDaySESs		1.3.6.1.4.1.4515.1.6.3.2.1.17.1.9
The path severely errored second (SES-P) is a count of 1-second intervals containing sonetSevereErrorThreshold or more EDC error (B3 byte), or one or more AIS-P, LOP-P, TIM-P or UNEQ-P defects which were encountered by the SONET path layer interface in a previous 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetPathDayUASs		1.3.6.1.4.1.4515.1.6.3.2.1.17.1.10
The path unavailable second (UAS-P) is a count of 1-second intervals for which the SONET STS-path was unavailable during a previous 1-day interval. The SONET STS-path becomes unavailable at the onset of 10 contiguous SES-Ps. The 10 SES-Ps are included in unavailable time. Once unavailable, the SONET STS-path becomes available at the onset of 10 contiguous seconds with no SES-Ps. The 10 seconds with no SES-Ps are excluded from unavailable time.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetPathDayFCs		1.3.6.1.4.1.4515.1.6.3.2.1.17.1.11
The number path failures count during a day.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetPathDayTcaFlag		1.3.6.1.4.1.4515.1.6.3.2.1.17.1.12
TRUE if one of the counters crossed the threshold during the day.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

sonetPathDayEBs		1.3.6.1.4.1.4515.1.6.3.2.1.17.1.13
The number path blocks in which one or more bits are in error counted during a day.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetPathDayReset		1.3.6.1.4.1.4515.1.6.3.2.1.17.1.14
Writing this object reset the PM counters of this interval.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetFarEndPathDayTable		1.3.6.1.4.1.4515.1.6.3.2.2.3
The SONET Far End Path Day table. Contains various statistics collected by each SONET Far End Path over multiple 1-day intervals of operation.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SonetFarEndPathDayEntry

sonetFarEndPathDayEntry		1.3.6.1.4.1.4515.1.6.3.2.2.3.1
An entry in the SONET Far End Path Day table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SonetFarEndPathDayEntry

sonetFarEndPathDayNumber		1.3.6.1.4.1.4515.1.6.3.2.2.3.1.1
A number which identifies the 1-day interval for which the set of far-end path related statistics is available. The number is between 1 and n, where n is the number of 1-day intervals supported by the agent. The interval identified by 1 is the current 1-day interval, 2 is the previous (most recently completed) 1-day interval and n is the least recently completed 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4

sonetFarEndPathDayStartTime		1.3.6.1.4.1.4515.1.6.3.2.2.3.1.2
This variable indicates the date and time at which the current interval of measurements began.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

sonetFarEndPathDayValidData		1.3.6.1.4.1.4515.1.6.3.2.2.3.1.3
This variable assumes the value true(1) if the data stored for this interval is both valid and complete. It is set to false(2) if the data stored for this interval is incomplete or otherwise invalid because (a) the data stored for this interval is for a period greater or less than 24 hours, or (b) some data is missing (e.g., when a near-end defect prevents some far-end data from being collected).
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

sonetFarEndPathDayCVs		1.3.6.1.4.1.4515.1.6.3.2.2.3.1.5
The far-end path code violation (CV-PFE) count is the number of REI-Ps (bit 1-4 in G1 byte) which were detected at the SONET STS-path layer interface in a previous 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetFarEndPathDayESs		1.3.6.1.4.1.4515.1.6.3.2.2.3.1.6
The far-end path errored second (ES-PFE) count is the number of 1-second intervals containing one or more REDC-P, or one or more RDI-P, ERDI-P server or ERDI-P connectivity defects which were encountered by the SONET STS-path layer interface in a previous 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetFarEndPathDaySESs		1.3.6.1.4.1.4515.1.6.3.2.2.3.1.9
The far-end path severely errored second (SES-PFE) is a count of 1-second intervals containing sonetSevereErrorThreshold or more REDC-Ps or one or more RDI-P, ERDI-P server or ERDI-P connectivity defects which were detected by the SONET STS-path layer interface in a previous 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetFarEndPathDayUASs		1.3.6.1.4.1.4515.1.6.3.2.2.3.1.10
The far-end path unavailable second (UAS-PFE) is a count of 1-second intervals for which the SONET STS-path was unavailable during a previous 1-day interval. The SONET STS-path becomes unavailable at the onset of 10 contiguous SES-PFEs. The 10 SES-PFEs are included in unavailable time. Once unavailable, the SONET STS-path becomes available at the onset of 10 contiguous seconds with no SES-PFEs. The 10 seconds with no SES-PFEs are excluded from unavailable time.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetFarEndPathDayFCs		1.3.6.1.4.1.4515.1.6.3.2.2.3.1.11
The far-end path failures count.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetFarEndPathDayTcaFlag		1.3.6.1.4.1.4515.1.6.3.2.2.3.1.12
TRUE if one of the counters crossed the threshold during the day.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

sonetFarEndPathDayEBs		1.3.6.1.4.1.4515.1.6.3.2.2.3.1.13
The count of far-end path blocks in which one or more bits are in error.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetFarEndPathDayReset		1.3.6.1.4.1.4515.1.6.3.2.2.3.1.14
Writing this object reset the PM counters of this interval.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetVTDefaultThresholdTable		1.3.6.1.4.1.4515.1.6.3.3.1.1
The table of default thresholds for SONET Path counters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SonetVTDefaultThresholdEntry

sonetVTDefaultThresholdEntry		1.3.6.1.4.1.4515.1.6.3.3.1.1.1
An entry in the table of default thresholds. The table has a variable for each counter type and accumulation period combination, but uses indexes to indetify the digital signal direction and rate. The agent must provide a set of default threshold values for all rates that the NE supports. The agent may make these variables read-only.
Status: current	Access: not-accessible
OBJECT-TYPE
	SonetVTDefaultThresholdEntry

sonetVTDefaultThresholdDirection		1.3.6.1.4.1.4515.1.6.3.3.1.1.1.1
The digital signal direction for which the default threshold values apply.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	nearEnd(1), farEnd(2)

sonetVTDefaultThresholdRate		1.3.6.1.4.1.4515.1.6.3.3.1.1.1.2
The path digital signal rate for which the default threshold values apply.
Status: current	Access: not-accessible
OBJECT-TYPE
	INTEGER	vt1dot5(1), vtg(2)

sonetVTDefaultCVThreshold		1.3.6.1.4.1.4515.1.6.3.3.1.1.1.3
The default value for SONET CV-V and CV-VFE counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..16383

sonetVTDefaultESThreshold		1.3.6.1.4.1.4515.1.6.3.3.1.1.1.4
The default value for SONET ES-V and ES-VFE counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..900

sonetVTDefaultSESThreshold		1.3.6.1.4.1.4515.1.6.3.3.1.1.1.5
The default value for SONET SES-V and SES-VFE counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..900

sonetVTDefaultUASThreshold		1.3.6.1.4.1.4515.1.6.3.3.1.1.1.6
The default value for SONET UAS-V and UAS-VFE counter 15-minute interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..900

sonetVTDefaultDayCVThreshold		1.3.6.1.4.1.4515.1.6.3.3.1.1.1.7
The default value for SONET CV-V and CV-VFE counter 1-day interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..1048575

sonetVTDefaultDayESThreshold		1.3.6.1.4.1.4515.1.6.3.3.1.1.1.8
The default value for SONET ES-V and ES-VFE counter 1-day interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..65535

sonetVTDefaultDaySESThreshold		1.3.6.1.4.1.4515.1.6.3.3.1.1.1.9
The default value for SONET SES-V and SES-VFE counter 1-day interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..4095

sonetVTDefaultDayUASThreshold		1.3.6.1.4.1.4515.1.6.3.3.1.1.1.10
The default value for SONET UAS-V and UAS-VFE counter 1-day interval thresholds.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	1..4095

sonetVTThresholdTable		1.3.6.1.4.1.4515.1.6.3.3.1.2
The table of trap threshold values for SONET Path counters.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SonetVTThresholdEntry

sonetVTThresholdEntry		1.3.6.1.4.1.4515.1.6.3.3.1.2.1
An entry in the table of SONET Path trap thresholds.
Status: current	Access: not-accessible
OBJECT-TYPE
	SonetVTThresholdEntry

sonetVTCurrentCVThreshold		1.3.6.1.4.1.4515.1.6.3.3.1.2.1.1
The trap threshold value for the interface's current 15-minute interval CV-V and CV-VFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..900

sonetVTCurrentESThreshold		1.3.6.1.4.1.4515.1.6.3.3.1.2.1.2
The trap threshold value for the interface's current 15-minute interval ES-V and ES-VFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..900

sonetVTCurrentSESThreshold		1.3.6.1.4.1.4515.1.6.3.3.1.2.1.3
The trap threshold value for the interface's current 15-minute interval SES-V and SES-VFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..900

sonetVTCurrentUASThreshold		1.3.6.1.4.1.4515.1.6.3.3.1.2.1.4
The trap threshold value for the interface's current 15-minute interval UAS-V and UAS-VFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..900

sonetVTDayCVThreshold		1.3.6.1.4.1.4515.1.6.3.3.1.2.1.5
The trap threshold value for the interface's current 1-day CV-V and CV-VFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

sonetVTDayESThreshold		1.3.6.1.4.1.4515.1.6.3.3.1.2.1.6
The trap threshold value for the interface's current 1-day ES-V and ES-VFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

sonetVTDaySESThreshold		1.3.6.1.4.1.4515.1.6.3.3.1.2.1.7
The trap threshold value for the interface's current 1-day SES-V and SES-VFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

sonetVTDayUASThreshold		1.3.6.1.4.1.4515.1.6.3.3.1.2.1.8
The trap threshold value for the interface's current 1-day UAS-V and UAS-VFE counters. A value of zero indicates that the default threshold value is to be used.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER	0..65535

sonetVTDayTable		1.3.6.1.4.1.4515.1.6.3.3.1.17
The SONET Path Day table. Contains performance statistics collected by each SONET Path over multiple 1-day intervals of operation.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SonetVTDayEntry

sonetVTDayEntry		1.3.6.1.4.1.4515.1.6.3.3.1.17.1
An entry in the SONET Path Day table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SonetVTDayEntry

sonetVTDayNumber		1.3.6.1.4.1.4515.1.6.3.3.1.17.1.1
A number which identifies the 1-day interval for which the set of near-end path related statistics is available. The number is between 1 and n, where n is the number of 1-day intervals supported by the agent. The interval identified by 1 is the current 1-day interval, 2 is the previous (most recently completed) 1-day interval and n is the least recently completed 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..33

sonetVTDayStartTime		1.3.6.1.4.1.4515.1.6.3.3.1.17.1.2
This variable indicates the date and time at which the 1-day interval of measurements began on this interface.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

sonetVTDayValidData		1.3.6.1.4.1.4515.1.6.3.3.1.17.1.3
This variable assumes the value true(1) if the data stored for this interval is both valid and complete. It is set to false(2) if the data stored for this interval is incomplete or otherwise invalid because (a) the data stored for this interval is for a period greater or less than 24 hours, or (b) some data is missing.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

sonetVTDayFCs		1.3.6.1.4.1.4515.1.6.3.3.1.17.1.4
The near-end path failure count (FC-V) is the number of occurences of near-end path failure events encountered by the SONET path layer interface in a previous 1-day interval. A near-end path failure event begins when the first of any of LOP-V, AIS-V or UNEQ-V failures is declared; a near-end path failure event ends when all LOP-V, AIS-V and UNEQ-V failures have cleared.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetVTDayCVs		1.3.6.1.4.1.4515.1.6.3.3.1.17.1.5
The path code violation (CV-V) count is the number of BIP-2 errors which were detected at the VT-path layer interface in a previous 1-day interval. CVs for the path layer are collected using the BIP-2 in the V5 byte located in the VT-path overhead.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetVTDayESs		1.3.6.1.4.1.4515.1.6.3.3.1.17.1.6
The path errored second (ES-V) count is the number of 1-second intervals containing one or more EDC error (V5 byte), or one or more AIS-V, LOP-V or UNEQ-V defects which were encountered by the SONET path layer interface in a previous 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetVTDaySESs		1.3.6.1.4.1.4515.1.6.3.3.1.17.1.7
The path severely errored second (SES-V) is a count of 1-second intervals containing sonetSevereErrorThreshold or more EDC error (V5 byte), or one or more AIS-V, LOP-V or UNEQ-V defects which were encountered by the SONET path layer interface in a previous 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetVTDayUASs		1.3.6.1.4.1.4515.1.6.3.3.1.17.1.8
The path unavailable second (UAS-V) is a count of 1-second intervals for which the SONET VT-path was unavailable during a previous 1-day interval. The SONET VT-path becomes unavailable at the onset of 10 contiguous SES-Vs. The 10 SES-Vs are included in unavailable time. Once unavailable, the SONET VT-path becomes available at the onset of 10 contiguous seconds with no SES-Vs. The 10 seconds with no SES-Vs are excluded from unavailable time.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetVTDayEBs		1.3.6.1.4.1.4515.1.6.3.3.1.17.1.9
The number VT path blocks in which one or more bits are in error counted during a day.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetVTDayTcaFlag		1.3.6.1.4.1.4515.1.6.3.3.1.17.1.10
TRUE if one of the counters crossed the threshold during the day.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

sonetVTDayReset		1.3.6.1.4.1.4515.1.6.3.3.1.17.1.11
Writing this object reset the PM counters of this interval.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetFarEndVTDayTable		1.3.6.1.4.1.4515.1.6.3.3.2.3
The SONET Far End Path Day table. Contains various statistics collected by each SONET Far End Path over multiple 1-day intervals of operation.
Status: current	Access: not-accessible
OBJECT-TYPE
	SEQUENCE OF
		SonetFarEndVTDayEntry

sonetFarEndVTDayEntry		1.3.6.1.4.1.4515.1.6.3.3.2.3.1
An entry in the SONET Far End Path Day table.
Status: current	Access: not-accessible
OBJECT-TYPE
	SonetFarEndVTDayEntry

sonetFarEndVTDayNumber		1.3.6.1.4.1.4515.1.6.3.3.2.3.1.1
A number which identifies the 1-day interval for which the set of far-end VT-path related statistics is available. The number is between 1 and n, where n is the number of 1-day intervals supported by the agent. The interval identified by 1 is the current 1-day interval, 2 is the previous (most recently completed) 1-day interval and n is the least recently completed 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	INTEGER	1..4

sonetFarEndVTDayStartTime		1.3.6.1.4.1.4515.1.6.3.3.2.3.1.2
This variable indicates the date and time at which the current interval of measurements began.
Status: current	Access: read-only
OBJECT-TYPE
	DateAndTime

sonetFarEndVTDayValidData		1.3.6.1.4.1.4515.1.6.3.3.2.3.1.3
This variable assumes the value true(1) if the data stored for this interval is both valid and complete. It is set to false(2) if the data stored for this interval is incomplete or otherwise invalid because (a) the data stored for this interval is for a period greater or less than 24 hours, or (b) some data is missing (e.g., when a near-end defect prevents some far-end data from being collected).
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

sonetFarEndVTDayFCs		1.3.6.1.4.1.4515.1.6.3.3.2.3.1.4
The far-end path failure count (FC-VFE) is the number of occurences of far-end path failure events detected by the SONET VT-path layer interface in a previous 1-day interval. A far-end path failure event begins when the first of any remote failure indication (RFI-V, RFI-V server, or RFI-V connectivity) failure is declared; a far-end path failure event ends when all RFI-V, RFI-V server, or RFI-V connectivity failures are cleared.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetFarEndVTDayCVs		1.3.6.1.4.1.4515.1.6.3.3.2.3.1.5
The far-end path code violation (CV-VFE) count is the number of REI-Vs (bit 1-4 in G1 byte) which were detected at the SONET VT-path layer interface in a previous 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetFarEndVTDayESs		1.3.6.1.4.1.4515.1.6.3.3.2.3.1.6
The far-end path errored second (ES-VFE) count is the number of 1-second intervals containing one or more REDC-V, or one or more RDI-V, ERDI-V server or ERDI-V connectivity defects which were encountered by the SONET VT-path layer interface in a previous 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetFarEndVTDaySESs		1.3.6.1.4.1.4515.1.6.3.3.2.3.1.7
The far-end path severely errored second (SES-VFE) is a count of 1-second intervals containing sonetSevereErrorThreshold or more REDC-Vs or one or more RDI-V, ERDI-V server or ERDI-V connectivity defects which were detected by the SONET VT-path layer interface in a previous 1-day interval.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetFarEndVTDayUASs		1.3.6.1.4.1.4515.1.6.3.3.2.3.1.8
The far-end path unavailable second (UAS-VFE) is a count of 1-second intervals for which the SONET VT-path was unavailable during a previous 1-day interval. The SONET VT-path becomes unavailable at the onset of 10 contiguous SES-VFEs. The 10 SES-VFEs are included in unavailable time. Once unavailable, the SONET VT-path becomes available at the onset of 10 contiguous seconds with no SES-VFEs. The 10 seconds with no SES-VFEs are excluded from unavailable time.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetFarEndVTDayEBs		1.3.6.1.4.1.4515.1.6.3.3.2.3.1.9
The number VT path blocks in which one or more bits are in error counted during a day detected by the Far End.
Status: current	Access: read-only
OBJECT-TYPE
	PerfTotalCount

sonetFarEndVTDayTcaFlag		1.3.6.1.4.1.4515.1.6.3.3.2.3.1.10
TRUE if one of the counters crossed the threshold during the day.
Status: current	Access: read-only
OBJECT-TYPE
	TruthValue

sonetFarEndVTDayReset		1.3.6.1.4.1.4515.1.6.3.3.2.3.1.11
Writing this object reset the PM counters of this interval.
Status: current	Access: read-write
OBJECT-TYPE
	INTEGER

sonetTrap		1.3.6.1.4.1.4515.1.6.3.1.6
OBJECT IDENTIFIER

sonetCounterId		1.3.6.1.4.1.4515.1.6.3.1.6.1
The OBJECT IDENTIFIER of the instance of the SONET counter that has crossed its threshold.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	OBJECT IDENTIFIER

sonetCounterValue		1.3.6.1.4.1.4515.1.6.3.1.6.2
The current value of the SONET counter that has crossed its threshold.
Status: current	Access: accessible-for-notify
OBJECT-TYPE
	Integer32

sonetThresholdCrossing		1.3.6.1.4.1.4515.1.6.3.1.6.3
This notification signifies that a counter has crossed its designated threshold. The term 'threshold crossing' means that a threshold has been reached or exceeded. A threshold crossing alert message (trap) signifies a performance degredation at or above the preset threshold value.
Status: current	Access: accessible-for-notify
NOTIFICATION-TYPE