SIAE-MAB-MIB
File:
SIAE-MAB-MIB.mib (21794 bytes)
Imported modules
Imported symbols
Defined Types
MabBwCalculationMethod |
|
This Textual Convention describes the method of calculation of the
radio bandwitdh (or the throughput of an interface):
- average: Average Tx BW value across the observation interval
- min: Minimum Tx BW value across the observation interval
- max: Maximum Tx BW value across the observation interval
|
TEXTUAL-CONVENTION |
|
|
|
|
INTEGER |
average(1), min(2), max(3) |
|
MabPduCompliance |
|
This Textual Convention describes the compliance of the MAB PDU
sent by a MAB PDU sender:
- stdMcmCompliant: PDU format is compliant with [1]
- extMcmCompliant: PDU format is compliant with [2]
- ituG8013Compliant: PDU format is compliant with [4]
Since [3] and [4] are a draft edition at the time when this MIB
is being written, the value ituG8013Compliant(3) is defined for
future use.
|
TEXTUAL-CONVENTION |
|
|
|
|
INTEGER |
stdMcmCompliant(1), extMcmCompliant(2), ituG8013Compliant(3) |
|
MabSenderOption |
|
This Textual Convention describes the supported option of a
MAB PDU sender:
- enableAlways: Enable periodic PDU sending even if the
current bandwidth is equal to the nominal
bandwidth.
- enableSignalFail: PDU are transmitted periodically when the
link fails in the tranmit direction. If the
NE usually sends PDUs also when the radio
bandwitdh (or the throughput of an interface)
is null, this option has no effect.
|
TEXTUAL-CONVENTION |
|
|
|
|
BITS |
enableAlways(0), enableSignalFail(1) |
|
MabSensorEntry |
|
SEQUENCE |
|
|
|
|
mabSensorIndex |
Integer32 |
|
|
mabSensorRowStatus |
RowStatus |
|
|
mabSensorAdminStatus |
INTEGER |
|
|
mabSensorIfIndex |
InterfaceIndex |
|
|
mabSensorLinkId |
Integer32 |
|
|
mabSensorBwMode |
MabBwCalculationMethod |
|
|
mabSensorHoldoffTime |
Integer32 |
|
|
mabSensorObservationTime |
Integer32 |
|
|
mabSensorFastTime |
Integer32 |
|
|
mabSensorFastCount |
Integer32 |
|
MabSensorStatusEntry |
|
SEQUENCE |
|
|
|
|
mabSensorNominalBw |
Integer32 |
|
|
mabSensorCurrentBw |
Integer32 |
|
MabPduSenderEntry |
|
SEQUENCE |
|
|
|
|
mabPduSenderIndex |
Integer32 |
|
|
mabPduSenderRowStatus |
RowStatus |
|
|
mabPduSenderAdminStatus |
INTEGER |
|
|
mabPduSenderIfIndex |
InterfaceIndex |
|
|
mabPduSenderSensorIndex |
Integer32 |
|
|
mabPduSenderVlanId |
Integer32 |
|
|
mabPduSenderPcp |
Integer32 |
|
|
mabPduSenderOamMaintLevel |
Integer32 |
|
|
mabPduSenderDAType |
INTEGER |
|
|
mabPduSenderUnicastDA |
MacAddress |
|
|
mabPduSenderOption |
MabSenderOption |
|
|
mabPduSenderPduCompliance |
MabPduCompliance |
|
Defined Values
mabMib |
1.3.6.1.4.1.3373.1103.93 |
Microwave Adaptive Bandwidth (MAB)
This management information module supports the configuration of
the MW Capacity Management (MCM) feature developed by
SIAE MICROELETTRONICA and Cisco that offers reliable QoS and
optimized performances even under worst radio propagation
conditions.
The extension to the original functionality, consisting of the
Link ID TLV, is considered by this MIB.
|
MODULE-IDENTITY |
|
|
|
mabMibVersion |
1.3.6.1.4.1.3373.1103.93.1 |
Numerical version of this module.
The string version of this MIB have the following format:
XX.YY.ZZ
so, for example, the value 1 should be interpreted as 00.00.01
and the value 10001 should be interpreted as 01.00.01.
|
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
INTEGER |
|
|
mabSensorTable |
1.3.6.1.4.1.3373.1103.93.2 |
Table with MAB sensors entries. Each sensor is associated to a
interface, usually an interface with the physical layer
consisting of a radio link, and comapares the current bandwidth
(throughput) with the nominal one. When nominal and current
bandwidth doesn't match to PDU senders associated with a sensor
is required to send a MAB PDU every observation time.
|
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
MabSensorEntry |
|
mabSensorEntry |
1.3.6.1.4.1.3373.1103.93.2.1 |
A row in the mabSensorTable.
|
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
MabSensorEntry |
|
|
mabSensorIndex |
1.3.6.1.4.1.3373.1103.93.2.1.1 |
This object identifies the MAB sensor inside the Network Element.
|
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
mabSensorRowStatus |
1.3.6.1.4.1.3373.1103.93.2.1.2 |
The status of this MAB sensor entry.
An entry may not exist in the active state unless all
objects in the entry have an appropriate value: mabSensorIfIndex
must be set to a valid ifIndex number. Otherwise, the error
inconsistentValue is returned on the attempt to set active this
row.
When set to notInService changes may be made to mabSensorIfIndex.
Other objects can be changed when mabSensorRowStatus is set to
active.
A sensor can not be deleted if there is any MAB PDU sender
associated with it.
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
RowStatus |
|
|
mabSensorAdminStatus |
1.3.6.1.4.1.3373.1103.93.2.1.3 |
Administative status of the MAB sensor.
The value down(1) turn off all MAB advisers associated with
this sensor.
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
INTEGER |
down(1), up(2) |
|
mabSensorIfIndex |
1.3.6.1.4.1.3373.1103.93.2.1.4 |
This object accepts a greater than zero value to identify an
interface in ifTable. The throughput of the selected interface
is monitored and notified to all MAB PDU sender associated with
this sensor.
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
InterfaceIndex |
|
|
mabSensorLinkId |
1.3.6.1.4.1.3373.1103.93.2.1.5 |
This object set the (radio) link identifier that will be inserted
in the Link ID TLV of the MAB PDU.
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
mabSensorBwMode |
1.3.6.1.4.1.3373.1103.93.2.1.6 |
This object defines the method of calculation of the current
bandwidth. The value of this parameter is sent inside MAB PDUs.
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
MabBwCalculationMethod |
|
|
mabSensorHoldoffTime |
1.3.6.1.4.1.3373.1103.93.2.1.7 |
This object defines the wait time (in seconds) for MAB protocol
before sending packets if the current bandwidth (throughput)
is lower than the nominal.
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
Integer32 |
10..60 |
|
mabSensorObservationTime |
1.3.6.1.4.1.3373.1103.93.2.1.8 |
This object defines the observation time (in seconds) for MAB
protocol during which calculate the minimum, maximum and average
value of the current bandwidth (throughput). At the end of each
period, a MAB PDU is sent by every MAB PDU sender associated with
this sensor.
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
Integer32 |
1 | 10 | 60 |
|
mabSensorFastTime |
1.3.6.1.4.1.3373.1103.93.2.1.9 |
This value is used in place of mabSensorObservationTime for the
first mabSensorFastCount PDU packets sent by a MAB PDU sender.
The value of mabSensorFastTime must be less than or equal to
mabSensorObservationTime.
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
Integer32 |
1..59 |
|
mabSensorFastCount |
1.3.6.1.4.1.3373.1103.93.2.1.10 |
This value specifies how many MAB PDU packets are sent every
mabSensorFastTime before to use the standard observation time
(mabSensorObservationTime).
Zero means which quick sending of packets is disabled.
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
Integer32 |
0..60 |
|
mabSensorStatusTable |
1.3.6.1.4.1.3373.1103.93.3 |
Table with the status of MAB sensor entries. For each row in
mabSensorTable a row is created in this table.
|
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
MabSensorStatusEntry |
|
mabSensorStatusEntry |
1.3.6.1.4.1.3373.1103.93.3.1 |
A row in the mabSensorTable.
|
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
MabSensorStatusEntry |
|
|
mabSensorNominalBw |
1.3.6.1.4.1.3373.1103.93.3.1.1 |
This object reports the nominal bandwidth (throughput) of the
interface selected by mabSensorIfIndex.
|
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
mabSensorCurrentBw |
1.3.6.1.4.1.3373.1103.93.3.1.2 |
This object reports the current bandwidth (throughput) of the
interface selected by mabSensorIfIndex and calculated according
to the method set in mabSensorBwMode.
|
Status: current |
Access: read-only |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
mabPduSenderTable |
1.3.6.1.4.1.3373.1103.93.4 |
Table with MAB PDU sender entries. Each PDU sender refers to an
ifIndex in ifTable on which to send a PDU MAB and a sensor that
triggers the sending.
|
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
SEQUENCE OF |
|
|
|
|
MabPduSenderEntry |
|
mabPduSenderEntry |
1.3.6.1.4.1.3373.1103.93.4.1 |
A row in the mabPduSenderTable.
|
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
MabPduSenderEntry |
|
|
mabPduSenderIndex |
1.3.6.1.4.1.3373.1103.93.4.1.1 |
This object identifies the MAB PDU sender inside the Network
Element.
|
Status: current |
Access: not-accessible |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
mabPduSenderRowStatus |
1.3.6.1.4.1.3373.1103.93.4.1.2 |
The status of this mabPduSender entry.
An entry may not exist in the active state unless all objects in
the entry have an appropriate value: mabPduSenderIfIndex must be
set to a valid ifIndex number and mabPduSenderSensorIndex must be
set to a valid MAB sensor, Otherwise, the error inconsistentValue
is returned on the attempt to set active this row.
When set to notInService changes may be made to mabPduSenderIfIndex,
mabPduSenderSensorIndex. Other objects can be changed when
mabPduSenderRowStatus is set to active.
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
RowStatus |
|
|
mabPduSenderAdminStatus |
1.3.6.1.4.1.3373.1103.93.4.1.3 |
Administative status of the MAB PDU sender.
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
INTEGER |
down(1), up(2) |
|
mabPduSenderIfIndex |
1.3.6.1.4.1.3373.1103.93.4.1.4 |
This object accepts a greater than zero value to identify an
interface in ifTable. MAB PDU is sent over this interface.
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
InterfaceIndex |
|
|
mabPduSenderSensorIndex |
1.3.6.1.4.1.3373.1103.93.4.1.5 |
This object associates a MAB sensor to this PDU sender.
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
Integer32 |
|
|
mabPduSenderVlanId |
1.3.6.1.4.1.3373.1103.93.4.1.6 |
This object defines the VLAN identifier used to tag the MAB PDU.
Zero means the PDU is not tagged.
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
Integer32 |
0 | 1..4094 |
|
mabPduSenderPcp |
1.3.6.1.4.1.3373.1103.93.4.1.7 |
This object defines packet priority written into the tag of
the MAB PDU.
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
Integer32 |
0..7 |
|
mabPduSenderOamMaintLevel |
1.3.6.1.4.1.3373.1103.93.4.1.8 |
This object defines the OAM maintenance level of the MAB PDU.
The multicast destination address of the PDU is according to
the selected maintenance level:
01-80-C2-00-00-3x
where x = Maintenance Level
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
Integer32 |
0..7 |
|
mabPduSenderDAType |
1.3.6.1.4.1.3373.1103.93.4.1.9 |
This object defines the destination MAC address type of the PDU:
- multicastDA(1): Multicast Class 1 Destination Address (DA)
- unicastDA(2): Unicast Destination Address (DA)
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
INTEGER |
multicastDA(1), unicastDA(2) |
|
mabPduSenderUnicastDA |
1.3.6.1.4.1.3373.1103.93.4.1.10 |
This object defines the unuicast destination address of the PDU
when mabPduSenderDAType is set to unicastDA(2).
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
MacAddress |
|
|
mabPduSenderOption |
1.3.6.1.4.1.3373.1103.93.4.1.11 |
This object enable the option supported by the MAB PDU sender:
- enableAlways: Enable periodic PDU sending even if the
current bandwidth is equal to the nominal
bandwidth.
- enableSignalFail: PDU are transmitted periodically when the
link fails in the tranmit direction. If the
NE usually sends PDUs also when the radio
bandwitdh (or the throughput of an interface)
is null, this option has no effect.
|
Status: current |
Access: read-create |
OBJECT-TYPE |
|
|
|
|
MabSenderOption |
|
|