SDSL-STATS-MIB

File: SDSL-STATS-MIB.mib (35786 bytes)

Imported modules

SNMPv2-SMI SNMPv2-TC IF-MIB
NNCGNI0001-SMI

Imported symbols

MODULE-IDENTITY OBJECT-TYPE NOTIFICATION-TYPE
Counter32 Gauge32 TEXTUAL-CONVENTION
TruthValue ifIndex nncExtensions

Defined Types

NncSdslLineStatusEntry  
SEQUENCE    
  nncSdslLineStatus INTEGER

NncSdslNearEndRawEntry  
SEQUENCE    
  nncSdslNearEndRawLOS Counter32
  nncSdslNearEndRawLowNM Counter32
  nncSdslNearEndRawLPR Counter32
  nncSdslNearEndRawLOCD Counter32
  nncSdslNearEndRawCRCError Counter32

NncSdslNearEndCurr15MinEntry  
SEQUENCE    
  nncSdslNearEndCurr15MinTimeElapsed Gauge32
  nncSdslNearEndCurr15MinLOSS Gauge32
  nncSdslNearEndCurr15MinLOSWS Gauge32
  nncSdslNearEndCurr15MinLowNMS Gauge32
  nncSdslNearEndCurr15MinLPRS Gauge32
  nncSdslNearEndCurr15MinErrS Gauge32

NncSdslNearEndCurr1DayEntry  
SEQUENCE    
  nncSdslNearEndCurr1DayTimeElapsed Gauge32
  nncSdslNearEndCurr1DayLOSS Gauge32
  nncSdslNearEndCurr1DayLOSWS Gauge32
  nncSdslNearEndCurr1DayLowNMS Gauge32
  nncSdslNearEndCurr1DayLPRS Gauge32
  nncSdslNearEndCurr1DayErrS Gauge32

NncSdslNearEndPrev1DayEntry  
SEQUENCE    
  nncSdslNearEndPrev1DayMoniSecs Gauge32
  nncSdslNearEndPrev1DayLOSS Gauge32
  nncSdslNearEndPrev1DayLOSWS Gauge32
  nncSdslNearEndPrev1DayLowNMS Gauge32
  nncSdslNearEndPrev1DayLPRS Gauge32
  nncSdslNearEndPrev1DayErrS Gauge32
  nncSdslNearEndPrev1DayValidData TruthValue

NncSdslFarEndAllEntry  
SEQUENCE    
  nncSdslFarEndRawLOCD Counter32
  nncSdslFarEndCurr15MinTimeElapsed Gauge32
  nncSdslFarEndCurr15MinErrS Gauge32
  nncSdslFarEndCurr1DayTimeElapsed Gauge32
  nncSdslFarEndCurr1DayErrS Gauge32
  nncSdslFarEndPrev1DayMoniSecs Gauge32
  nncSdslFarEndPrev1DayErrS Gauge32
  nncSdslFarEndPrev1DayValidData TruthValue

NncSdslNearEndIntEntry  
SEQUENCE    
  nncSdslNearEndIntNumber INTEGER
  nncSdslNearEndIntLOSS Gauge32
  nncSdslNearEndIntLOSWS Gauge32
  nncSdslNearEndIntLowNMS Gauge32
  nncSdslNearEndIntLPRS Gauge32
  nncSdslNearEndIntErrS Gauge32
  nncSdslNearEndIntValidData TruthValue

NncSdslFarEndIntEntry  
SEQUENCE    
  nncSdslFarEndIntNumber INTEGER
  nncSdslFarEndIntErrS Gauge32
  nncSdslFarEndIntValidData TruthValue

Defined Values

nncSdslStatistics 1.3.6.1.4.1.123.3.64
This module contains definitions for SDSL Ports Stats.
MODULE-IDENTITY    

nncSdslStatisticsObjects 1.3.6.1.4.1.123.3.64.1
OBJECT IDENTIFIER    

nncSdslLineStatusTable 1.3.6.1.4.1.123.3.64.1.1
Table that contains the Status of all SDSL Lines.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NncSdslLineStatusEntry

nncSdslLineStatusEntry 1.3.6.1.4.1.123.3.64.1.1.1
The Status of an SDSL Line.
Status: current Access: not-accessible
OBJECT-TYPE    
  NncSdslLineStatusEntry  

nncSdslLineStatus 1.3.6.1.4.1.123.3.64.1.1.1.1
Status indicates current state of the line. Unknown 0 Operational 1 Near End Loss Of Cell Delineation 2 Near End Loss Of Signal 3 Near End Loss Of Power 34
Status: current Access: read-only
OBJECT-TYPE    
  INTEGER 1..34  

nncSdslNearEndRawTable 1.3.6.1.4.1.123.3.64.1.2
Table that contains the Near End RAW Stats of all SDSL Ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NncSdslNearEndRawEntry

nncSdslNearEndRawEntry 1.3.6.1.4.1.123.3.64.1.2.1
The Near End Raw Stats of an SDSL Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  NncSdslNearEndRawEntry  

nncSdslNearEndRawLOS 1.3.6.1.4.1.123.3.64.1.2.1.1
Count of the number of Loss of Signal failures since system reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nncSdslNearEndRawLowNM 1.3.6.1.4.1.123.3.64.1.2.1.2
Count of the number of Low Noise Margin failures since system reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nncSdslNearEndRawLPR 1.3.6.1.4.1.123.3.64.1.2.1.3
Count of the number of Loss of Power failures since system reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nncSdslNearEndRawLOCD 1.3.6.1.4.1.123.3.64.1.2.1.4
Count of the number of Loss of Cell Delineation failures since system reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nncSdslNearEndRawCRCError 1.3.6.1.4.1.123.3.64.1.2.1.5
Count of the number of CRC Errors since system reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nncSdslNearEndCurr15MinTable 1.3.6.1.4.1.123.3.64.1.3
Table that contains the Near End 15 minutes current Stats of all SDSL Ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NncSdslNearEndCurr15MinEntry

nncSdslNearEndCurr15MinEntry 1.3.6.1.4.1.123.3.64.1.3.1
The Near End 15 minutes current Stats of an SDSL Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  NncSdslNearEndCurr15MinEntry  

nncSdslNearEndCurr15MinTimeElapsed 1.3.6.1.4.1.123.3.64.1.3.1.1
Total elapsed seconds in this interval. A full interval is 900 seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..900  

nncSdslNearEndCurr15MinLOSS 1.3.6.1.4.1.123.3.64.1.3.1.2
Count of the number of seconds in Loss of Signal status not due to a Loss of Power in the current 15 minutes interval.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndCurr15MinLOSWS 1.3.6.1.4.1.123.3.64.1.3.1.3
Count of the number of seconds in Loss of Synch Word status not followed by a Loss of Signal in the current 15 minutes interval.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndCurr15MinLowNMS 1.3.6.1.4.1.123.3.64.1.3.1.4
Count of the number of seconds in Low Noise Margin status in the current 15 minutes interval.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndCurr15MinLPRS 1.3.6.1.4.1.123.3.64.1.3.1.5
Count of the number of seconds in Loss of Power status in the current 15 minutes interval.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndCurr15MinErrS 1.3.6.1.4.1.123.3.64.1.3.1.6
Count of Errored Seconds in the current 15 minutes interval. The errored second parameter is a count of one-second intervals containing one or more of the anomolies or defects previously defined.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndCurr1DayTable 1.3.6.1.4.1.123.3.64.1.4
Table that contains the Near End 1 Day current Stats of all SDSL Ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NncSdslNearEndCurr1DayEntry

nncSdslNearEndCurr1DayEntry 1.3.6.1.4.1.123.3.64.1.4.1
The Near End 1 Day current Stats of an SDSL Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  NncSdslNearEndCurr1DayEntry  

nncSdslNearEndCurr1DayTimeElapsed 1.3.6.1.4.1.123.3.64.1.4.1.1
Number of seconds that have elapses since the beginning of the current 1 Day interval.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndCurr1DayLOSS 1.3.6.1.4.1.123.3.64.1.4.1.2
Count of the number of seconds in Loss of Signal status not due to a Loss of Power during the current day.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndCurr1DayLOSWS 1.3.6.1.4.1.123.3.64.1.4.1.3
Count of the number of seconds in Loss of Synch Word status not followed by a Loss of Signal during the current day.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndCurr1DayLowNMS 1.3.6.1.4.1.123.3.64.1.4.1.4
Count of the number of seconds in Low Noise Margin status during the current day.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndCurr1DayLPRS 1.3.6.1.4.1.123.3.64.1.4.1.5
Count of the number of seconds in Loss of Power status during the current day.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndCurr1DayErrS 1.3.6.1.4.1.123.3.64.1.4.1.6
Count of Errored Seconds during the current day. The errored second parameter is a count of one-second intervals containing one or more of the anomolies or defects previously defined.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndPrev1DayTable 1.3.6.1.4.1.123.3.64.1.5
Table that contains the Near End 1 DAY PREVIOUS Stats of all SDSL Ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NncSdslNearEndPrev1DayEntry

nncSdslNearEndPrev1DayEntry 1.3.6.1.4.1.123.3.64.1.5.1
The Near End 1 Day PREVIOUS Stats of an SDSL Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  NncSdslNearEndPrev1DayEntry  

nncSdslNearEndPrev1DayMoniSecs 1.3.6.1.4.1.123.3.64.1.5.1.1
The time in the PREVIOUS 1-day interval over which the performance monitoring information is actually counted. This value will normally be the same as the total interval duration except in a situation where performance monitoring information can not be collected for any reason. Typically Elapsed 1-day Time will be copied into Monitored Seconds when the 1-day roll-over occurs.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndPrev1DayLOSS 1.3.6.1.4.1.123.3.64.1.5.1.2
Count of the number of seconds in Loss of Signal status not due to a Loss of Power within the most recent PREVIOUS 1 day period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndPrev1DayLOSWS 1.3.6.1.4.1.123.3.64.1.5.1.3
Count of the number of seconds in Loss of Synch Word status not followed by a Loss of Signal within the most recent PREVIOUS 1 day period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndPrev1DayLowNMS 1.3.6.1.4.1.123.3.64.1.5.1.4
Count of the number of seconds in Low Noise Margin status within the most recent PREVIOUS 1 day period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndPrev1DayLPRS 1.3.6.1.4.1.123.3.64.1.5.1.5
Count of the number of seconds in Loss of Power status within the most recent PREVIOUS 1 day period.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndPrev1DayErrS 1.3.6.1.4.1.123.3.64.1.5.1.6
Count of Errored Seconds within the most recent PREVIOUS 1 day period. The errored second parameter is a count of one-second intervals containing one or more of the anomolies or defects previously defined.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndPrev1DayValidData 1.3.6.1.4.1.123.3.64.1.5.1.7
This variable indicates if there is valid data for this interval.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

nncSdslFarEndAllTable 1.3.6.1.4.1.123.3.64.1.6
Table that contains ALL the Far End Stats of all SDSL Ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NncSdslFarEndAllEntry

nncSdslFarEndAllEntry 1.3.6.1.4.1.123.3.64.1.6.1
ALL the Far End Stats of an SDSL Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  NncSdslFarEndAllEntry  

nncSdslFarEndRawLOCD 1.3.6.1.4.1.123.3.64.1.6.1.1
Count of the number of Loss of Cell Delineation failures since system reset.
Status: current Access: read-only
OBJECT-TYPE    
  Counter32  

nncSdslFarEndCurr15MinTimeElapsed 1.3.6.1.4.1.123.3.64.1.6.1.2
Total elapsed seconds in this interval. A full interval is 900 seconds.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32 0..900  

nncSdslFarEndCurr15MinErrS 1.3.6.1.4.1.123.3.64.1.6.1.3
Count of Errored Seconds in the current 15 minutes interval. The errored second parameter is a count of one-second intervals containing one or more of the anomolies or defects previously defined.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslFarEndCurr1DayTimeElapsed 1.3.6.1.4.1.123.3.64.1.6.1.4
Number of seconds that have elapses since the beginning of the current 1 Day interval.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslFarEndCurr1DayErrS 1.3.6.1.4.1.123.3.64.1.6.1.5
Count of Errored Seconds in the current 15 minutes interval. The errored second parameter is a count of one-second intervals containing one or more of the anomolies or defects previously defined.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslFarEndPrev1DayMoniSecs 1.3.6.1.4.1.123.3.64.1.6.1.6
The time in the PREVIOUS 1-day interval over which the performance monitoring information is actually counted. This value will normally be the same as the total interval duration except in a situation where performance monitoring information can not be collected for any reason. Typically Elapsed 1-day Time will be copied into Monitored Seconds when the 1-day roll-over occurs.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslFarEndPrev1DayErrS 1.3.6.1.4.1.123.3.64.1.6.1.7
Count of Errored Seconds within the most recent PREVIOUS 1 day period. The errored second parameter is a count of one-second intervals containing one or more of the anomolies or defects previously defined.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslFarEndPrev1DayValidData 1.3.6.1.4.1.123.3.64.1.6.1.8
This variable indicates if there is valid data for this interval.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

nncSdslNearEndIntTable 1.3.6.1.4.1.123.3.64.1.7
Table that contains the Near End 15 Minutes Intervals Stats of all SDSL Ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NncSdslNearEndIntEntry

nncSdslNearEndIntEntry 1.3.6.1.4.1.123.3.64.1.7.1
One interval of Near End Stats of an SDSL Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  NncSdslNearEndIntEntry  

nncSdslNearEndIntNumber 1.3.6.1.4.1.123.3.64.1.7.1.1
Performance Data Interval number. 1 is the the most recent interval; interval 96 is 24 hours ago. Interval 2..96 are optional.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..96  

nncSdslNearEndIntLOSS 1.3.6.1.4.1.123.3.64.1.7.1.2
Count of seconds in the interval when there was Loss of Signal not due to a Loss of Power.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndIntLOSWS 1.3.6.1.4.1.123.3.64.1.7.1.3
Count of seconds in the interval when there was Loss of Signal not folloew by Loss of Signal.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndIntLowNMS 1.3.6.1.4.1.123.3.64.1.7.1.4
Count of seconds in the interval when there was Low Noise Margin.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndIntLPRS 1.3.6.1.4.1.123.3.64.1.7.1.5
Count of seconds in the interval when there was Loss of Power.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndIntErrS 1.3.6.1.4.1.123.3.64.1.7.1.6
Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more of the anomolies or defects previously defined.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslNearEndIntValidData 1.3.6.1.4.1.123.3.64.1.7.1.7
This variable indicates if there is valid data for this interval.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue  

nncSdslFarEndIntTable 1.3.6.1.4.1.123.3.64.1.8
Table that contains the Far End 15 Minutes Intervals Stats of all SDSL Ports.
Status: current Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    NncSdslFarEndIntEntry

nncSdslFarEndIntEntry 1.3.6.1.4.1.123.3.64.1.8.1
One interval of Far End Stats of an SDSL Port.
Status: current Access: not-accessible
OBJECT-TYPE    
  NncSdslFarEndIntEntry  

nncSdslFarEndIntNumber 1.3.6.1.4.1.123.3.64.1.8.1.1
Performance Data Interval number. 1 is the the most recent interval; interval 96 is 24 hours ago. Interval 2..96 are optional.
Status: current Access: not-accessible
OBJECT-TYPE    
  INTEGER 1..96  

nncSdslFarEndIntErrS 1.3.6.1.4.1.123.3.64.1.8.1.2
Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more of the anomolies or defects previously defined.
Status: current Access: read-only
OBJECT-TYPE    
  Gauge32  

nncSdslFarEndIntValidData 1.3.6.1.4.1.123.3.64.1.8.1.3
This variable indicates if there is valid data for this interval.
Status: current Access: read-only
OBJECT-TYPE    
  TruthValue