SANMgrV1-MIB

File: SANMgrV1-MIB.mib (134152 bytes)

Imported modules

RFC1155-SMI RFC-1212 RFC1213-MIB
RFC-1215

Imported symbols

TimeTicks IpAddress Gauge
enterprises experimental OBJECT-TYPE
DisplayString TRAP-TYPE

Defined Types

ProductID  
OBJECT IDENTIFIER    

PathlightProduct  
INTEGER sanGateway(1), sanRouter(2), sanBridge(3), adicFCR2(4), dellFCR2(5), siemensFCR2(6), sanHoneoye(7), adicHoneoye(8), dellHoneoye(9), siemensHoneoye(10), ibmGatewayModule(11)    

Boolean  
INTEGER true(1), false(2)    

RowStatus  
INTEGER active(1), notInService(2), notReady(3), createAndGo(4), createAndWait(5), destroy(6)    

LogCommand  
INTEGER idle(0), snapshot(1), scroll(2), save(3), clear(4), removeFile(5), logModeCurrent(6), logModeAbsolute(7), doHealthCheck(8)    

PltStatus  
INTEGER failed(1), down(2), testing(3), up(4)    

FcStatus  
INTEGER configWait(0), loopInit(1), login(2), ready(3), lostSync(4), error(5), reinit(6), nonPart(7), failed(8)    

Interface  
INTEGER none(0), sanGateway(1), ssa(2), fibreChannel(3), scsi(4), ethernet(5), unknown(6), any(7), sanReplication(8)    

Reset  
INTEGER run(0), reset(1), reboot(2)    

BaudRate  
INTEGER baud9600(0), baud19200(1), baud38400(2)    

HealthCheckLevel  
INTEGER none(0), system(1), interface(2), simpleDevice(3), deviceReady(4)    

LogViewingLevel  
INTEGER private(0), notice(1), warning(2), information(3)    

DeviceType  
INTEGER directAccess(0), sequentialAccess(1), printer(2), processor(3), worm(4), cd(5), scanner(6), opticalMemory(7), mediumChanger(8), communications(9), ascIt81(10), ascIt82(11), storageArrayController(12), enclosure(13), simplifiedDirectAccess(14), opticalCardReader(15), unknown(31)    

VendorIDInt  
INTEGER unknown(0), symbios(4096), amd(4130), qlogic(4215), pathlight(4537)    

FibreMedia  
INTEGER unknown(0), copper(1), shortWaveOptical(2), longWaveOptical(3), shortWaveOpticalDual(4), longWaveOpticalDual(5), shortWaveOpticalLongDistance(6), longWaveOpticalLongDistance(7), gbicSWOneGB(8), gbicLW1300OneGB(9), gbicLW1300HPOneGB(10), gbicLW1550HPOneGB(11), gbicCopperHSSDCOneGB(12), gbicCopperDB9OneGB(13), gbicSWTwoGB(14), gbicLW1300TwoGB(15), gbicLW1300HPTwoGB(16), gbicLW1550HPTwoGB(17), gbicCopperHSSDCTwoGB(18), gbicCopperDB9TwoGB(19), noGBIC(20)    

FibrePort  
INTEGER nodeLoop(0), node(1), fabricLoop(3), fabric(4), none(255)    

FibreLoopIDMode  
INTEGER soft(0), hard(1)    

FibrePortMode  
INTEGER privateTargetOnly(1), privateInitiatorOnly(2), privateTargetAndInitiator(3), publicTargetOnly(17), publicInitiatorOnly(18), publicTargetAndInitiator(19)    

FibreConnOptions  
INTEGER loopOnly(0), pointToPointOnly(1), loopPreferred(2), pointToPointPreferred(3)    

SsaSpeed  
INTEGER ssa80(1), ssa160(2)    

PathingAlgorithm  
INTEGER default(0), skipInitiators(1), unknown(2)    

ScsiSpeed  
INTEGER async(0), fast(1), ultra(2), ultra2(3), ultra160(4)    

ScsiRole  
INTEGER target(0), initiator(1)    

ScsiTermination  
INTEGER disabled(0), enabled(1), notPresent(2)    

ScsiCardType  
INTEGER none(0), differentialNoTermination(1), differentialTerminated(2), singleEndedNoTermination(3), singleEndedTerminated(4), unknown(5), lowVoltageSingleEnded(6), lowVoltageDifferential(7), lowVoltageMultiFunction(8)    

ScsiAnsiLevel  
INTEGER notScsi(0), scsi-1(1), scsi-2(2), scsi-3(3)    

LogEntry  
SEQUENCE    
  paIndex INTEGER
  paTime TimeTicks
  paProducer INTEGER
  paEventClass INTEGER
  paEventCode INTEGER
  paSeq INTEGER
  paEventVars DisplayString Size(0..256)

DevEntry  
SEQUENCE    
  pdIndex INTEGER
  pdUID DisplayString Size(16)
  pdType DeviceType
  pdVendor DisplayString Size(8)
  pdProduct DisplayString Size(16)
  pdBlockSize INTEGER
  pdCapacity Gauge
  pdAccess INTEGER
  pdRemovable Boolean
  pdStatus PltStatus
  pdSpeed INTEGER
  pdWidth INTEGER
  pdSerial DisplayString Size(0..32)
  pdIdentify INTEGER
  pdInterfaceType Interface
  pdBus INTEGER
  pdId INTEGER
  pdLun INTEGER
  pdCtlrIndex INTEGER
  pdHWRev DisplayString Size(0..32)
  pdFWRev DisplayString Size(0..32)
  pdReset Reset
  pdStatusBits INTEGER
  pdScsiAnsiLevel ScsiAnsiLevel
  pdTargetLun INTEGER
  pdIpAddress IpAddress

CtlrEntry  
SEQUENCE    
  pcIndex INTEGER
  pcType Interface
  pcVendorId VendorIDInt
  pcProductId INTEGER
  pcRevision DisplayString Size(0..32)
  pcSubVendor INTEGER
  pcSubProduct INTEGER
  pcMaxBurst INTEGER
  pcLatency INTEGER 0..255
  pcIdentify INTEGER
  pcPCIBus INTEGER
  pcPCIDev INTEGER
  pcPCIFunc INTEGER
  pcReset Reset
  pcRescan Boolean
  pcLED OCTET STRING Size(2)
  pcHWRev DisplayString Size(0..32)
  pcFWRev DisplayString Size(0..32)
  pcPCISlot INTEGER
  pcPMCSlot INTEGER
  pcPCIClass OCTET STRING Size(3)
  pcSplitMode Boolean
  pcChannelMask Gauge
  pcPortHostType DisplayString Size(0..32)

FcCtlrEntry  
SEQUENCE    
  fcStatus FcStatus
  fcMaxSpeed Gauge
  fcWWID DisplayString Size(17)
  fcFWRev DisplayString Size(0..32)
  fcHWRev DisplayString Size(0..32)
  fcLoopID INTEGER -1..127
  fcFrameSize INTEGER
  fcPortType FibrePort
  fcMedia FibreMedia
  fcSerialNumber DisplayString Size(0..32)
  fcLoopIDMode FibreLoopIDMode
  fcALPhysicalAddress INTEGER
  fcPortMode FibrePortMode
  fcConnectionOptions FibreConnOptions
  fcCtlrChipType INTEGER
  fcTapeFeature Boolean
  fcHardID INTEGER -1..256
  fcCurrentSpeedSetting INTEGER
  fcCurrentSpeed INTEGER
  fcFrameBufferSize INTEGER
  fcLinkFailureCount INTEGER
  fcLossSyncCount INTEGER
  fcLossSignalCount INTEGER
  fcProtocolErrorCount INTEGER
  fcInvalidTxWordCount INTEGER
  fcInvalidCRCCount INTEGER
  fcWWNodeName DisplayString Size(17)

SSACtlrEntry  
SEQUENCE    
  ssaStatus1 PltStatus
  ssaStatus2 PltStatus
  ssaSpeed SsaSpeed
  ssaUID DisplayString Size(16)
  ssaFWRev DisplayString Size(0..32)
  ssaMaxTarg Gauge
  ssaMaxInit Gauge
  ssaPathAlg PathingAlgorithm
  ssaHWRev DisplayString Size(0..32)
  ssaMasterPriority INTEGER 0..7
  ssaSATAQuota INTEGER 0..255
  ssaSATBQuota INTEGER 0..255
  ssaSATIQuota INTEGER 0..255

SCSICtlrEntry  
SEQUENCE    
  scsiStatus PltStatus
  scsiSpeed ScsiSpeed
  scsiRole ScsiRole
  scsiHostId INTEGER
  scsiMaxSpeed ScsiSpeed
  scsiTerm ScsiTermination
  scsiIoCard ScsiCardType
  scsiMaxIds INTEGER
  scsiMaxLuns INTEGER
  scsiMaxWidth INTEGER
  scsiFWRev DisplayString Size(0..32)
  scsiHWRev DisplayString Size(0..32)
  scsiResetOnPowerUp Boolean
  scsiMultiInitEnabled Boolean
  scsiAlternateHostId INTEGER

TrapDestEntry  
SEQUENCE    
  pnIndex INTEGER
  pnIPAddr IpAddress
  pnUdpPort INTEGER 0..65535
  pnTrapStyle INTEGER

InitiatorEntry  
SEQUENCE    
  hostIndex INTEGER
  hostRowStatus INTEGER
  hostWWName DisplayString Size(0..32)
  hostName DisplayString Size(0..32)
  hostType DisplayString Size(0..32)
  hostPortID DisplayString Size(0..32)
  hostSANConnection INTEGER
  hostConnectionType INTEGER
  hostITLData OCTET STRING Size(256)
  hostIPAddr IpAddress

ScsiMapEntry  
SEQUENCE    
  scsiMapRowStatus RowStatus
  scsiMapPort INTEGER
  scsiMapTid INTEGER
  scsiMapLun INTEGER
  scsiMapAssignedLun INTEGER
  scsiMapComments DisplayString Size(0..80)
  scsiMapPdIndex INTEGER

DevMapEntry  
SEQUENCE    
  dmRowStatus RowStatus
  dmAssignedLun INTEGER
  dmType Interface
  dmPort INTEGER
  dmTargetId INTEGER
  dmTargetLun INTEGER
  dmUid OCTET STRING Size(8)

SRSDevEntry  
SEQUENCE    
  srsDevId INTEGER
  srsDevState INTEGER
  srsDevCommand INTEGER
  srsDevAssignedLun INTEGER
  srsDevMemberCount INTEGER
  srsDevMembersOnline INTEGER
  srsDevFlags INTEGER
  srsDevSizeInBlocks Gauge
  srsDevBlockSize INTEGER
  srsDevPrimary INTEGER

SRSMemEntry  
SEQUENCE    
  srsMemDeviceId INTEGER
  srsMemId INTEGER
  srsMemState INTEGER
  srsMemCommand INTEGER
  srsMemType INTEGER
  srsMemSyncPoint INTEGER
  srsMemAssignedLun INTEGER
  srsMemReadOptions INTEGER
  srsMemWriteOptions INTEGER

EnvDataEntry  
SEQUENCE    
  envDataId INTEGER
  envDataName DisplayString Size(0..64)
  envNominalLo DisplayString Size(0..32)
  envNominalHi DisplayString Size(0..32)
  envWarningLo DisplayString Size(0..32)
  envWarningHi DisplayString Size(0..32)
  envCurValue DisplayString Size(0..32)
  envCurStatus DisplayString Size(0..32)
  envUnit DisplayString Size(0..32)

Defined Values

pathlight 0.1.2935
OBJECT IDENTIFIER    

products 0.1.2935.1
OBJECT IDENTIFIER    

agent 0.1.2935.2
OBJECT IDENTIFIER    

devices 0.1.2935.3
OBJECT IDENTIFIER    

controllers 0.1.2935.4
OBJECT IDENTIFIER    

notification 0.1.2935.5
OBJECT IDENTIFIER    

panelLED 0.1.2935.6
OBJECT IDENTIFIER    

paHost 0.1.2935.7
OBJECT IDENTIFIER    

scsiMap 0.1.2935.8
OBJECT IDENTIFIER    

deviceMap 0.1.2935.9
OBJECT IDENTIFIER    

replication 0.1.2935.10
OBJECT IDENTIFIER    

envData 0.1.2935.11
OBJECT IDENTIFIER    

trapDefinition 0.1.2935.1000
OBJECT IDENTIFIER    

sanGateway 0.1.2935.1.1
OBJECT IDENTIFIER    

sanGateway1 1.1
OBJECT IDENTIFIER    

sanGateway2 1.2
OBJECT IDENTIFIER    

paIdentify 0.1.2935.2.1
Flash the READY light on the SAN Data Gateway front panel. A non-zero value turns the LED on for the specified number of seconds. Zero turns LED off.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

paReboot 0.1.2935.2.2
Writing a reboot(2) value here causes immediate reboot.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Reset  

paHealthCheckValue 0.1.2935.2.3
Value in percent of health check tests passed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

paHealthCheckLevel 0.1.2935.2.4
Scrutiny level of health check function.
Status: mandatory Access: read-write
OBJECT-TYPE    
  HealthCheckLevel  

paHealthCheckInterval 0.1.2935.2.5
Health Check interval in minutes.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

paEvRptLevel 0.1.2935.2.6
Used when retrieving Event Log. Events with log level greater than paEvRptLevel are not retrieved.
Status: mandatory Access: read-write
OBJECT-TYPE    
  LogViewingLevel  

paEventLogLevels 0.1.2935.2.7
Each of 255 event types has an 8-bit level used when reading log. Currently valid LogLevel range is 0-3.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(256)  

paTrapThresholds 0.1.2935.2.8
Each of 255 event types has an 8-bit threshold. When the number of events exceeds the Trap Threshold, a trap is generated and sent to all parties listed in the trap destination table (also under SNMP control) . Threshold 0 means Never Threshold 1 means Always Threshold 2 - 255 means Number of events per 10 minute period
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(256)  

paBaudRate 0.1.2935.2.9
Serial baud rate for SAN Gateway Service Port. Currently, the Agent does not support baud rate change: the rate is hard-coded to 19200 baud.
Status: mandatory Access: read-write
OBJECT-TYPE    
  BaudRate  

paEventLog 0.1.2935.2.10
Entry point for the Agent Event Log Table.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    LogEntry

paEventLogEntry 0.1.2935.2.10.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  LogEntry  

paIndex 0.1.2935.2.10.1.1
MIB EventLogEntry Table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

paTime 0.1.2935.2.10.1.2
Time stamp (since boot).
Status: mandatory Access: read-only
OBJECT-TYPE    
  TimeTicks  

paProducer 0.1.2935.2.10.1.3
Numeric identifier for this event's producer.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

paEventClass 0.1.2935.2.10.1.4
Numeric identifier for this event's class.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

paEventCode 0.1.2935.2.10.1.5
Numeric code for this event.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

paSeq 0.1.2935.2.10.1.6
Sequence number (relative record number) since boot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

paEventVars 0.1.2935.2.10.1.7
Text description of event.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..256)  

paLogSize 0.1.2935.2.11
Number of records in entire event log. (Not just current records since boot.)
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

paCommand 0.1.2935.2.12
Used for issuing command to SNMP agent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  LogCommand  

paLogBoot 0.1.2935.2.13
Absolute index of first log entry at boot.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

paLogNCurrent 0.1.2935.2.14
SNMP Get (read) returns number of records since boot subject to viewing level filtering. SNMP Set (write) copies this number of records since boot (subject to level filtering) into a buffer from which records are read. This mode of use is deprecated. The preferred way to get the event log since boot is to read paLogBoot, set paEvRptLevel and do a series of SNMP GetNext calls starting at instance paLogBoot until end of event log MIB table is reached.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

paLogChronFirst 0.1.2935.2.15
Used to request range of records from paLogChronFirst to paLogChronLast
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

paLogChronLast 0.1.2935.2.16
Used to request range of records from paLogChronFirst to paLogChronLast
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

paLogScroll 0.1.2935.2.17
Used to request previous/next range of records event log
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

paLogFilename 0.1.2935.2.18
Used to save event log to a file.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..128)  

paEnvironmentState 0.1.2935.2.19
Temperature and Voltage Status of SAN Data Gateway: ********************************** (LSB) bit 0 Auxiliary Power bit 1 Main Power bit 2 Temperature Warning bit 3 Temperature Alarm
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

paGatewayFWRev 0.1.2935.2.20
SAN Data Gateway Firmware Revision information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

paGatewayHWRev 0.1.2935.2.21
SAN Data Gateway Hardware Revision information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

paSnmpFWRev 0.1.2935.2.22
SNMP Agent Firmware Revision information.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

paRidTag 0.1.2935.2.23
SAN Data Gateway RIDTag.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..128)  

paSerialNumber 0.1.2935.2.24
SAN Data Gateway Serial Number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

paServerVersion 0.1.2935.2.25
Remote Management software writes Server version information here to customize SNMP Agent behavior.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

paProductType 0.1.2935.2.26
Type of SAN device
Status: mandatory Access: read-only
OBJECT-TYPE    
  PathlightProduct  

paVPSEnabled 0.1.2935.2.27
State of ITL Access Control enable.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Boolean  

paLicenseKey 0.1.2935.2.28
Used to pass feature enabling license keys.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..64)  

paThirdPartyCopyEnabled 0.1.2935.2.29
State of Extended 3rd Party Copy enable. Enabled means that a valid license key has been entered for this feature.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Boolean  

paVPSStatus 0.1.2935.2.30
State of Virtual Private SAN feature. bit 0 : active or inactive. bit 1 : licensed or not licensed. Bit 1 is redundant with MIB var paVPSEnabled. Writing 1 to bit 0 makes VPS active if licensed. Writing 0 to bit 0 makes VPS inactive if licensed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

paThirdPartyCopyStatus 0.1.2935.2.31
State of Extended 3rd Party Copy feature. bit 0 : active or inactive. bit 1 : licensed or not licensed. Bit 1 is redundant with MIB var paThirdPartyCopyEnabled. Writing 1 to bit 0 makes Third Party Copy active if licensed. Writing 0 to bit 0 makes Third Party Copy inactive if licensed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

paCommandControlLUN 0.1.2935.2.32
Gateway/Router Command and Control LUN
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

paSanDirectorEnabled 0.1.2935.2.33
State of SAN Director Support for this device. To enable, user must write a valid license key to OID paLicenseKey or enter the license key from the service port.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Boolean  

paNodeName 0.1.2935.2.34
SAN Gateway Node Name.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(8)  

paVPMStatus 0.1.2935.2.35
State of Virtual Private Map feature. bit 0 : active or inactive. bit 1 : licensed or not licensed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

paSRSStatus 0.1.2935.2.36
State of SAN Replication Services feature. bit 0 : active or inactive. bit 1 : licensed or not licensed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

paEthernetType 0.1.2935.2.37
Current Ethernet Speed.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString  

paTrapSequenceNumber 0.1.2935.2.38
Sequence number of last trap sent by this SNMP Agent.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

paSysNodeNameMode 0.1.2935.2.39
Algorithm used when computing Fibre Channel World Wide Node Name for each port. If the value is sameForEachPort(0), then the World Wide Node Name is the same for each port and computed based on the World Wide Node Name of the gateway. If the value is differentForEachPort(1), then the World Wide Node Name is different for each port, computed based on the World Wide Port Name for that port.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER sameForEachPort(0), differentForEachPort(1)  

pdDevices 0.1.2935.3.1
Pathlight Physical Device Group *********************************** Each device attached to the Gateway has an entry here.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DevEntry

pdDevEntry 0.1.2935.3.1.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DevEntry  

pdIndex 0.1.2935.3.1.1.1
MIB table index
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdUID 0.1.2935.3.1.1.2
Universal Identifier
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(16)  

pdType 0.1.2935.3.1.1.3
Device Type i.e. disk/tape/cd etc.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DeviceType  

pdVendor 0.1.2935.3.1.1.4
Device Vendor
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(8)  

pdProduct 0.1.2935.3.1.1.5
Device Product Identifier
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(16)  

pdBlockSize 0.1.2935.3.1.1.6
Block size in Bytes
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdCapacity 0.1.2935.3.1.1.7
Capacity in BLOCKS (see pdBlockSize)
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

pdAccess 0.1.2935.3.1.1.8
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdRemovable 0.1.2935.3.1.1.9
Is device removable ?
Status: mandatory Access: read-only
OBJECT-TYPE    
  Boolean  

pdStatus 0.1.2935.3.1.1.10
Device Status
Status: mandatory Access: read-only
OBJECT-TYPE    
  PltStatus  

pdSpeed 0.1.2935.3.1.1.11
Device Speed in MBytes/second
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdWidth 0.1.2935.3.1.1.12
Data path width in bits
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdSerial 0.1.2935.3.1.1.13
Device Serial Number
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

pdIdentify 0.1.2935.3.1.1.14
Number of seconds to flash identifying LED. Write here to flash LED on device if supported by Gateway and device. Zero turns LED off.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

pdInterfaceType 0.1.2935.3.1.1.15
This device's type of communication interface.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Interface  

pdBus 0.1.2935.3.1.1.16
SCSI bus number
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdId 0.1.2935.3.1.1.17
SCSI Address ID
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdLun 0.1.2935.3.1.1.18
SCSI Logical Unit Number.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdCtlrIndex 0.1.2935.3.1.1.19
Index of this device's controller in the Controllers MIB table and type-specific controller tables
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdHWRev 0.1.2935.3.1.1.20
Device hardware revision number/identifier
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

pdFWRev 0.1.2935.3.1.1.21
Device firmware revision number/identifier
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

pdReset 0.1.2935.3.1.1.22
Generic device reset if supported. Write reset(1) here to reset device if supported by Gateway firmware and device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Reset  

pdStatusBits 0.1.2935.3.1.1.23
Device status bits as per SCSI spec.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdScsiAnsiLevel 0.1.2935.3.1.1.24
Device SCSI level.
Status: mandatory Access: read-only
OBJECT-TYPE    
  ScsiAnsiLevel  

pdTargetLun 0.1.2935.3.1.1.25
This target device's Logical Unit Number as seen from attached host.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pdIpAddress 0.1.2935.3.1.1.26
This target device's IP Address if applicable. In case of SAN Gateway or Router, this information is used to allow arbitrary drill-down capability.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

pcControllers 0.1.2935.4.1
Pathlight Controller Group ******************************* All controllers installed in the SAN Data Gateway have an entry here AND a parallel entry in the controller-type specific table (Fibre Channnel, SSA, or SCSI).
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    CtlrEntry

pcCtlrEntry 0.1.2935.4.1.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  CtlrEntry  

pcIndex 0.1.2935.4.1.1.1
MIB Table index.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pcType 0.1.2935.4.1.1.2
Communication Interface type.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Interface  

pcVendorId 0.1.2935.4.1.1.3
Integer vendor ID for this controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  VendorIDInt  

pcProductId 0.1.2935.4.1.1.4
Vendor's integer ID for this controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pcRevision 0.1.2935.4.1.1.5
Revision information for this controller. See also pcHWRev and pcFWRev.
Status: deprecated Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

pcSubVendor 0.1.2935.4.1.1.6
Integer sub-vendor ID for this controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pcSubProduct 0.1.2935.4.1.1.7
Vendor's integer sub-product ID for this controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pcMaxBurst 0.1.2935.4.1.1.8
Maximum burst transfer rate in MBytes/second
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

pcLatency 0.1.2935.4.1.1.9
Latency Timer in Clock Ticks.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..255  

pcIdentify 0.1.2935.4.1.1.10
Reserved for flashing identifying LED on device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

pcPCIBus 0.1.2935.4.1.1.11
PCI Bus number in SAN Data Gateway for this controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pcPCIDev 0.1.2935.4.1.1.12
PCI device number in SAN Data Gateway for this controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pcPCIFunc 0.1.2935.4.1.1.13
PCI Function number in SAN Data Gateway for this contoller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pcReset 0.1.2935.4.1.1.14
Generic controller reset variable. Not supported for all controller types.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Reset  

pcRescan 0.1.2935.4.1.1.15
Writing true(1) here causes controller to rescan its bus if rescan is supported for this controller type.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Boolean  

pcLED 0.1.2935.4.1.1.16
Is LED on?
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(2)  

pcHWRev 0.1.2935.4.1.1.17
Hardware revision for this controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

pcFWRev 0.1.2935.4.1.1.18
Firmware revision for this controller
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

pcPCISlot 0.1.2935.4.1.1.19
Location of Channel Card on PCI bus
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pcPMCSlot 0.1.2935.4.1.1.20
Location of Card: PMC 1, 2 or 3. 0=> Not a PMC card
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

pcPCIClass 0.1.2935.4.1.1.21
Device class code as per PCI specification.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(3)  

pcSplitMode 0.1.2935.4.1.1.22
Enable/Disable Split Mode for this controller.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Boolean  

pcChannelMask 0.1.2935.4.1.1.23
Specifies access permissions for this initiator in bits 0 through 18 ************************************************* -* SCSI Channels *- Bit 0 => Is access DISALLOWED to SCSI channel 1 ? Bit 1 => Is access DISALLOWED to SCSI channel 2 ? Bit 2 => Is access DISALLOWED to SCSI channel 3 ? Bit 3 => Is access DISALLOWED to SCSI channel 4 ? -* Ultra SCSI Channels *- Bit 4 => Is access DISALLOWED to Ultra SCSI channel 1 ? Bit 5 => Is access DISALLOWED to Ultra SCSI channel 2 ? Bit 6 => Is access DISALLOWED to Ultra SCSI channel 3 ? Bit 7 => Is access DISALLOWED to Ultra SCSI channel 4 ? Bit 8 => Is access DISALLOWED to Ultra SCSI channel 5 ? Bit 9 => Is access DISALLOWED to Ultra SCSI channel 6 ? -* Fibre Channel *- Bit 10 => Is access DISALLOWED to Fibre Channel 1 ? Bit 11 => Is access DISALLOWED to Fibre Channel 2 ? Bit 12 => Is access DISALLOWED to Fibre Channel 3 ? Bit 13 => Is access DISALLOWED to Fibre Channel 4 ? Bit 14 => Is access DISALLOWED to Fibre Channel 5 ? Bit 15 => Is access DISALLOWED to Fibre Channel 6 ? -* SSA Channels *- Bit 16 => Is access DISALLOWED to SSA channel 1 ? Bit 17 => Is access DISALLOWED to SSA Channel 2 ? Bit 18 => Is access DISALLOWED to SSA Channel 3 ?
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

pcPortHostType 0.1.2935.4.1.1.24
Host type for this port. Used if VPS is not enabled.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

pcFCCtlrs 0.1.2935.4.2
Entry point for Fibre Channel Controller Device Group ****************************************************** This table parallels the Controller Table: a Fibre Channel controller with pcIndex N in the controller table appears here as index N as well, and in general there are rows in this table which are empty.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    FcCtlrEntry

fcCtlrEntry 0.1.2935.4.2.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  FcCtlrEntry  

fcStatus 0.1.2935.4.2.1.1
Status of the Fibre Channel Controller
Status: mandatory Access: read-only
OBJECT-TYPE    
  FcStatus  

fcMaxSpeed 0.1.2935.4.2.1.2
Maximum Transfer Speed in MBytes per second.
Status: mandatory Access: read-only
OBJECT-TYPE    
  Gauge  

fcWWID 0.1.2935.4.2.1.3
World Wide Identifier for this Fibre Channel Controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(17)  

fcFWRev 0.1.2935.4.2.1.4
Firmware revision number/identifier for this Fibre Channel Controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

fcHWRev 0.1.2935.4.2.1.5
Hardware revision number/identifier for this Fibre Channel Controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

fcLoopID 0.1.2935.4.2.1.6
Fibre Channel Loop ID. soft = -1
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -1..127  

fcFrameSize 0.1.2935.4.2.1.7
Fibre Channel frame size.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

fcPortType 0.1.2935.4.2.1.8
Fibre Channel Port Type
Status: mandatory Access: read-write
OBJECT-TYPE    
  FibrePort  

fcMedia 0.1.2935.4.2.1.9
Media type for this Fibre Channel Controller
Status: mandatory Access: read-only
OBJECT-TYPE    
  FibreMedia  

fcSerialNumber 0.1.2935.4.2.1.10
Serial Number for this Fibre Channel Controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

fcLoopIDMode 0.1.2935.4.2.1.11
Fibre Channel Loop ID mode (soft or hard)
Status: mandatory Access: read-only
OBJECT-TYPE    
  FibreLoopIDMode  

fcALPhysicalAddress 0.1.2935.4.2.1.12
Arbitrated Loop Physical Address (ALPA)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fcPortMode 0.1.2935.4.2.1.13
Fibre Channel Port Mode.
Status: mandatory Access: read-write
OBJECT-TYPE    
  FibrePortMode  

fcConnectionOptions 0.1.2935.4.2.1.14
Connection options for ISP2200 FC chip. Values 4 - 8 are reserved.
Status: mandatory Access: read-write
OBJECT-TYPE    
  FibreConnOptions  

fcCtlrChipType 0.1.2935.4.2.1.15
Type of Fibre Channel controller chip. Valid types are 2100 , 2200 for QLogic ISP2100 and ISP2200 chips.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fcTapeFeature 0.1.2935.4.2.1.16
Status of Fibre Channel Tape Specification support. true means this controller supports FC Tape false means this controller does not support FC Tape
Status: mandatory Access: read-only
OBJECT-TYPE    
  Boolean  

fcHardID 0.1.2935.4.2.1.17
Fibre Channel Hard ID, the preferred loop ID for this controller. Even if the controller is in Hard Loop ID mode, the actual loop ID is not guaranteed to be fcHardID.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -1..256  

fcCurrentSpeedSetting 0.1.2935.4.2.1.18
Speed in Gb/sec. 0: Auto, 1: 1Gb, 2: 2Gb
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

fcCurrentSpeed 0.1.2935.4.2.1.19
Current Speed Indicator Gb/sec.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fcFrameBufferSize 0.1.2935.4.2.1.20
Fibre Channel Frame Buffer Size
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fcLinkFailureCount 0.1.2935.4.2.1.21
Fibre Channel Link Failure Count
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fcLossSyncCount 0.1.2935.4.2.1.22
Fibre Channel Loss of Sync Count
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fcLossSignalCount 0.1.2935.4.2.1.23
Fibre Channel Loss of Signal Count
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fcProtocolErrorCount 0.1.2935.4.2.1.24
Fibre Channel Primitive Sequence Protocol Error Count
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fcInvalidTxWordCount 0.1.2935.4.2.1.25
Fibre Channel Invalid Transmission Word Count
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fcInvalidCRCCount 0.1.2935.4.2.1.26
Fibre Channel Invalid CRC Count
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

fcWWNodeName 0.1.2935.4.2.1.27
The World Wide Node Name for this Fibre Channel Controller. The Node Name for this port may computer strictly on the World Wide Node Name for the gateway, or on a per port basis which uses the World Wide Port Name (fcWWID), thus giving each port a different Node Name. See paSysNodeNameMode to get or set which algorithm is in use.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(17)  

pcSSACtlrs 0.1.2935.4.3
Entry point for SSA Controller Device Group **************************************************** This table parallels the Controller Table: an SSA controller with pcIndex N in the controller table appears here as row index N as well, and in general there are rows in this table which are empty.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SSACtlrEntry

ssaCtlrEntry 0.1.2935.4.3.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SSACtlrEntry  

ssaStatus1 0.1.2935.4.3.1.1
Status on port 1 of dual port SSA card
Status: mandatory Access: read-only
OBJECT-TYPE    
  PltStatus  

ssaStatus2 0.1.2935.4.3.1.2
Status on port 2 of dual port SSA card
Status: mandatory Access: read-only
OBJECT-TYPE    
  PltStatus  

ssaSpeed 0.1.2935.4.3.1.3
SSA transfer speed 80 Mbytes/second or 160 MBytes/second
Status: mandatory Access: read-write
OBJECT-TYPE    
  SsaSpeed  

ssaUID 0.1.2935.4.3.1.4
Universal Identifier for this SSA Controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(16)  

ssaFWRev 0.1.2935.4.3.1.5
Firmware revision number/identifier for this SSA controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

ssaMaxTarg 0.1.2935.4.3.1.6
Maximum number of targets supported.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

ssaMaxInit 0.1.2935.4.3.1.7
Maximum number of initiators supported.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

ssaPathAlg 0.1.2935.4.3.1.8
SSA pathing algorithm.
Status: mandatory Access: read-write
OBJECT-TYPE    
  PathingAlgorithm  

ssaHWRev 0.1.2935.4.3.1.9
Hardware revision number/identifier for this SSA controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

ssaMasterPriority 0.1.2935.4.3.1.10
The SSA Master Priority of an SSA node is a number from 0 to 7. SSA initiators elect a master based on this priority. If more than one SSA node has the same priority then the node with the highest UID is elected. Pathlight SSA host adapters default to a Master Priority of 4. SAN Gateway SSA Target adapters default to a priority of 5 to ensure that the Gateway node will be master in a multi-initiator loop. This value should never be set to 7 because this is the priority used to guarantee mastership to a node that is entering Service Mode.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..7  

ssaSATAQuota 0.1.2935.4.3.1.11
The SSA SAT Quota A parameter is an 8 bit number that determines 'the maximum number of frames which can be originated from this port before the port is SATisfied and forwards the SAT character. A value of zero means that no SATs are forwarded or issued from this port.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

ssaSATBQuota 0.1.2935.4.3.1.12
The SSA SAT Quota B parameter is an 8 bit number that determines 'the maximum number of frames which this port can originate without forwarding a SAT character. A value of zero means that an infinite number of frames can be sent without being subject to SAT pacing.'
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

ssaSATIQuota 0.1.2935.4.3.1.13
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER 0..255  

pcSCSICtlrs 0.1.2935.4.4
Entry point for SCSI Controller Device Group **************************************************** This table parallels the Controller Table: a SCSI controller with pcIndex N in the controller table appears here as row index N as well, and in general there are rows in this table which are empty.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SCSICtlrEntry

scsiCtlrEntry 0.1.2935.4.4.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SCSICtlrEntry  

scsiStatus 0.1.2935.4.4.1.1
Status for this SCSI controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  PltStatus  

scsiSpeed 0.1.2935.4.4.1.2
SCSI Transaction speed.
Status: mandatory Access: read-write
OBJECT-TYPE    
  ScsiSpeed  

scsiRole 0.1.2935.4.4.1.3
Is this a Target or Initiator ?
Status: mandatory Access: read-write
OBJECT-TYPE    
  ScsiRole  

scsiHostId 0.1.2935.4.4.1.4
Host ID defaults to 7.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..15  

scsiMaxSpeed 0.1.2935.4.4.1.5
Maximum Speed of this SCSI Channel.
Status: mandatory Access: read-write
OBJECT-TYPE    
  ScsiSpeed  

scsiTerm 0.1.2935.4.4.1.6
State of internal SCSI bus terminations, if any.
Status: mandatory Access: read-write
OBJECT-TYPE    
  ScsiTermination  

scsiIoCard 0.1.2935.4.4.1.7
Type of SCSI controller hardware.
Status: mandatory Access: read-only
OBJECT-TYPE    
  ScsiCardType  

scsiMaxIds 0.1.2935.4.4.1.8
Maximum Number of IDs for this SCSI controller.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scsiMaxLuns 0.1.2935.4.4.1.9
Maximum Number of LUNs for this SCSI controller.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scsiMaxWidth 0.1.2935.4.4.1.10
Maximum transfer width in bits.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scsiHWRev 0.1.2935.4.4.1.11
Hardware revision for this SCSI controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

scsiFWRev 0.1.2935.4.4.1.12
Firmware revision for this SCSI controller.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

scsiResetOnPowerUp 0.1.2935.4.4.1.13
Enables/Disables SCSI bus reset upon Gateway power-up for this SCSI controller.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Boolean  

scsiMultiInitEnabled 0.1.2935.4.4.1.14
Enables/Disables multi-initiator support on for this SCSI controller.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Boolean  

scsiAlternateHostId 0.1.2935.4.4.1.15
Alternate Host ID for this SCSI controller. -1 means use automatic.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER -1..15  

pnTrapDest 0.1.2935.5.1
Trap destination Group Table ****************************************** A list of IP addresses to which SNMP Traps are sent in parallel using UDP Port 162.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    TrapDestEntry

pnTrapDestEntry 0.1.2935.5.1.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  TrapDestEntry  

pnIndex 0.1.2935.5.1.1.1
Index into TrapDest table
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

pnIPAddr 0.1.2935.5.1.1.2
IP Address of destination entity to which traps are sent.
Status: mandatory Access: read-write
OBJECT-TYPE    
  IpAddress  

pnUdpPort 0.1.2935.5.1.1.3
UDP Port on which traps are sent to this entity.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER 0..65535  

pnTrapStyle 0.1.2935.5.1.1.4
Style to be used when building a trap PDU to be sent to this entity. A value of proprietary(1) selects the proprietary format used by the Pathlight SAN Director management application. A value of rfc1215(2) selects the format as described in the RFC 1215 TRAP-TYPE objects included in this MIB document. The default is proprietary(1).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER proprietary(1), rfc1215(2)  

ledReady 0.1.2935.6.1
ON/OFF state of READY LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

ledAuxPower 0.1.2935.6.2
ON/OFF state of AUXILIARY POWER LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

ledMainPower 0.1.2935.6.3
ON/OFF state of MAIN POWER LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

ledTempAlarm 0.1.2935.6.4
ON/OFF state of Temperature Alarm LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

ledTempWarn 0.1.2935.6.5
ON/OFF state of Temperature Warning LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

ledEtherCollision 0.1.2935.6.6
Is Ethernet Collison LED on?
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

ledEtherTransmit 0.1.2935.6.7
ON/OFF state of Ethernet Transmit LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  


ledScsi1 0.1.2935.6.9
ON/OFF state of SCSI Channel 1 LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

ledScsi2 0.1.2935.6.10
ON/OFF state of SCSI Channel 2 LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

ledScsi3 0.1.2935.6.11
ON/OFF state of SCSI Channel 3 LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

ledScsi4 0.1.2935.6.12
ON/OFF state of SCSI Channel 4 LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

ledActivity1 0.1.2935.6.13
ON/OFF state of Network Connection Channel 1 Activity LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

ledActivity2 0.1.2935.6.14
ON/OFF state of Network Connection Channel 2 Activity LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

ledActivity3 0.1.2935.6.15
ON/OFF state of Network Connection Channel 3 Activity LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

ledStatus1 0.1.2935.6.16
ON/OFF state of Network Connection Channel 1 Status LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

ledStatus2 0.1.2935.6.17
ON/OFF state of Network Connection Channel 2 Status LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

ledStatus3 0.1.2935.6.18
ON/OFF state of Network Connection Channel 1 Status LED.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

ledAll 0.1.2935.6.19
All LED values in one INTEGER Value *********************************************** Bit 0 Ready Bit 8 Scsi1 Bit 1 AuxPower Bit 9 Scsi2 Bit 2 MainPower Bit 10 Scsi3 Bit 3 TempAlarm Bit 11 Scsi4 Bit 4 TempWarn Bit 12 Activity1 Bit 5 EtherCollision Bit 13 Activity2 Bit 6 EtherTransmit Bit 14 Activity3 Bit 7 EtherLink Bit 15 Status1 Bit 16 Status2 Bit 17 Status3 Bit 18 Error Bit 19 Ethernet Speed
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

ledError 0.1.2935.6.20
Turned on to indicate an Alarm or Warning condition.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

ledEthernetSpeed 0.1.2935.6.21
ON/OFF state of Ethernet Speed indicator LED. 0 means 10 Base-T , 1 means 100 Base-T.
Status: mandatory Access: read-only
OBJECT-TYPE    
  OCTET STRING Size(1)  

hostCommand 0.1.2935.7.1
Used to issue commands to ITL control software.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

hostInitiator 0.1.2935.7.2
Attached Host Group Table *************************** List of attached hosts and pertinent information.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    InitiatorEntry

hostInitiatorEntry 0.1.2935.7.2.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  InitiatorEntry  

hostIndex 0.1.2935.7.2.1.1
Index into Host Initiator table
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

hostRowStatus 0.1.2935.7.2.1.2
Row Status for this row.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

hostWWName 0.1.2935.7.2.1.3
World Wide name of this Initiator.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

hostName 0.1.2935.7.2.1.4
Name for this Initiator.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

hostType 0.1.2935.7.2.1.5
Operating System and other host environment information.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

hostPortID 0.1.2935.7.2.1.6
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..32)  

hostSANConnection 0.1.2935.7.2.1.7
SAN Connection (1-6) to which this host is connected.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

hostConnectionType 0.1.2935.7.2.1.8
Type of SAN connection (FCAL , etc.)
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

hostITLData 0.1.2935.7.2.1.9
ITL Access Control data for this host. 256 possible LUNs with one Byte of data per LUN.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(256)  

hostIPAddr 0.1.2935.7.2.1.10
IP Address of this host. Host is not required to have an IP address.
Status: mandatory Access: read-only
OBJECT-TYPE    
  IpAddress  

scsiMapCommand 0.1.2935.8.1
Used to issue commands to SCSI Channel map map routines.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scsiChannelMap 0.1.2935.8.2
SCSI Channel Device Map Table ****************************** List of devices presented to SCSI attached initiator. The initiator sees a series of (Target ID , LUN ) SCSI targets which are mapped to a logical device identified by a Pathlight assigned LUN.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    ScsiMapEntry

scsiMapEntry 0.1.2935.8.2.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  ScsiMapEntry  

scsiMapRowStatus 0.1.2935.8.2.1.1
Specifies the state of the row.
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

scsiMapPort 0.1.2935.8.2.1.2
SCSI port (bus) number for this entry (1 thru 10).
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scsiMapTid 0.1.2935.8.2.1.3
SCSI Target ID for this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scsiMapLun 0.1.2935.8.2.1.4
SCSI LUN for this entry.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

scsiMapAssignedLun 0.1.2935.8.2.1.5
Pathlight LUN assigned to this entry. This assigned LUN maps to some device connected to the Gateway/Router by some other means (FC, SSA, SCSI, ...).
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

scsiMapComments 0.1.2935.8.2.1.6
User's comments for this entry.
Status: mandatory Access: read-write
OBJECT-TYPE    
  DisplayString Size(0..80)  

scsiMapPdIndex 0.1.2935.8.2.1.7
Index into Pathlight SANMgr MIB Device Table ( pd group ). The Device Table has more detailed information about attached devices.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

deviceMapCommand 0.1.2935.9.1
Used to issue commands to device map map routines.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER clearCopy(1), commit(2), winnow(3), mapClearDatabase(4)  

dmDeviceMap 0.1.2935.9.2
Device Map Group *********************************** Each device attached to the Gateway has an entry here. Historical data of devices not presently connected may also appear here.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    DevMapEntry

dmDevMapEntry 0.1.2935.9.2.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  DevMapEntry  

dmRowStatus 0.1.2935.9.2.1.1
Row Control Object for this row
Status: mandatory Access: read-write
OBJECT-TYPE    
  RowStatus  

dmAssignedLun 0.1.2935.9.2.1.2
Logical Unit Number assigned to this attached device. Range is 0 thru 255.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

dmType 0.1.2935.9.2.1.3
Type of device (FC, SCSI, SNA, SSA).
Status: mandatory Access: read-write
OBJECT-TYPE    
  Interface  

dmPort 0.1.2935.9.2.1.4
SAN Gateway Port to which this device is connected. May be 1 thru 10 for SCSI, 1 thru 6 for Fibre Channel, 1 thru 3 for SSA.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

dmTargetId 0.1.2935.9.2.1.5
The Target ID of the attached target device. This is the actual target ID of the device, not fabricated by the Gateway or Router.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

dmTargetLun 0.1.2935.9.2.1.6
The Logical Unit Number of the attached target device. This is the actual LUN of the device, not fabricated by the Gateway or Router.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

dmUid 0.1.2935.9.2.1.7
A universally unique identifier for this target device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  OCTET STRING Size(8)  

srsDevTable 0.1.2935.10.1
Entry point for SAN Replication Service Device Group ***************************************************** Each SAN Replication Service Device has an entry in this table
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SRSDevEntry

srsDevEntry 0.1.2935.10.1.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SRSDevEntry  

srsDevId 0.1.2935.10.1.1.1
Device ID for this SRS Device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srsDevState 0.1.2935.10.1.1.2
State of this LUN Replicated Device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), initialized(1), online(2), error(3), deleted(4)  

srsDevCommand 0.1.2935.10.1.1.3
Used to invoke SAN Replication Services API commands. Parameters may be passed in the same SNMP Set varbind list with the srsDevCommand as the last varbind. ********************************************* create(1) - Creates a new SRS Device delete(2) - Deletes an existing SRS Device
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER create(1), remove(2)  

srsDevAssignedLun 0.1.2935.10.1.1.4
Assigned LUN of the SAN Replication Service Device's Primary.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

srsDevMemberCount 0.1.2935.10.1.1.5
Number of members of this LUN Replicated Device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srsDevMembersOnline 0.1.2935.10.1.1.6
Number of members online.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srsDevFlags 0.1.2935.10.1.1.7
SCSI device flags for this SAN Replication Service Device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

srsDevSizeInBlocks 0.1.2935.10.1.1.8
Size in blocks of this SAN Replication Services Device.
Status: mandatory Access: read-write
OBJECT-TYPE    
  Gauge  

srsDevBlockSize 0.1.2935.10.1.1.9
Block size in octets.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

srsDevPrimary 0.1.2935.10.1.1.10
The Assigned LUN of this SRS Device's Primary.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

srsMemTable 0.1.2935.10.2
Entry point for SAN Replication Services Member Group ***************************************************** This table lists the Members of each SRS Device.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    SRSMemEntry

srsMemEntry 0.1.2935.10.2.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SRSMemEntry  

srsMemDeviceId 0.1.2935.10.2.1.1
Device ID of the SAN Replication Services Device to which this member belongs.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srsMemId 0.1.2935.10.2.1.2
Member ID (index) of this member device.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srsMemState 0.1.2935.10.2.1.3
State of this SAN Replication Services Device Member.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER unknown(0), online(1), synchronized(2), synchronizing(3), suspended(4), readError(5), writeError(6), offline(7)  

srsMemCommand 0.1.2935.10.2.1.4
Used to invoke SAN Replication Services API methods. Parameters may be passed in the same SNMP Set varbind list with the lrmCommand as the last varbind.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER memberAdd(1), suspend(2), resume(3), remove(4), primarySet(5), fullSynchronize(6), quickSynchronize(7), memberChange(8)  

srsMemType 0.1.2935.10.2.1.5
Is this device a primary or secondary member.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER primary(1), secondary(2)  

srsMemSyncPoint 0.1.2935.10.2.1.6
Number of blocks synchronized so far. Used for monitoring synchronization.
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

srsMemAssignedLun 0.1.2935.10.2.1.7
Assigned LUN for this SRS Member.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER  

srsMemReadOptions 0.1.2935.10.2.1.8
SRS Member read options.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER enabled(0), disabled(1)  

srsMemWriteOptions 0.1.2935.10.2.1.9
SRS Member write options.
Status: mandatory Access: read-write
OBJECT-TYPE    
  INTEGER synchronous(0), asynchronous(1)  

envDataTable 0.1.2935.11.1
Entry point for Environmental Data Group ***************************************************** This table lists the attributes of each environmental data.
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  SEQUENCE OF  
    EnvDataEntry

envDataEntry 0.1.2935.11.1.1
Status: mandatory Access: not-accessible
OBJECT-TYPE    
  EnvDataEntry  

envDataId 0.1.2935.11.1.1.1
Tok_String
Status: mandatory Access: read-only
OBJECT-TYPE    
  INTEGER  

envDataName 0.1.2935.11.1.1.2
Name of this environmental data
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..64)  

envNominalLo 0.1.2935.11.1.1.3
Minimum value for Nominal status Warning state occurs if the current value is less than this
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

envNominalHi 0.1.2935.11.1.1.4
Maximum Value for Nominal status Warning state occurs if the current value is greater than this.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

envWarningLo 0.1.2935.11.1.1.5
Minimum value for Warning status Alarm state occurs if the current value is less than this
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

envWarningHi 0.1.2935.11.1.1.6
Maximum Value for Warning status Alarm state occurs if the current value is greater than this.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

envCurValue 0.1.2935.11.1.1.7
Current Value.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

envCurStatus 0.1.2935.11.1.1.8
Current Status: Nominal, Warning, or Alarm.
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

envUnit 0.1.2935.11.1.1.9
Unit
Status: mandatory Access: read-only
OBJECT-TYPE    
  DisplayString Size(0..32)  

ssaPortUpEvent 1
An SSA Port Up Event has occurred.
TRAP-TYPE    

ssaPortDownEvent 2
An SSA Port Down Event has occurred.
TRAP-TYPE    

ssaUidAddedEvent 3
An SSA UID Added Event has occurred.
TRAP-TYPE    

ssaUidRemovedEvent 4
An SSA UID Removed Event has occurred.
TRAP-TYPE    

ssaWebReconfiguredEvent 5
An SSA Web Reconfigured Event has occurred.
TRAP-TYPE    

ssaAsyncErrorEvent 6
An SSA Async Error Event has occurred.
TRAP-TYPE    

ssaAdapterEvent 7
An SSA Adapter Event has occurred.
TRAP-TYPE    

senseDataEvent 8
Sense Data recorded following a check condition. Normally, the host system will request and process sense data, and then perform error recovery.
TRAP-TYPE    

unitAttentionEvent 9
A LUN reports a unit attention condition on a non-removable media device.
TRAP-TYPE    

ibfEvent 10
An Internal Bus Fault event has occurred.
TRAP-TYPE    

temperatureChangeEvent 11
A temperature sensor has reported a change from one of three possible states to a another. The possible states are OK, High, Very High. The display string contained in the varbind paEventVars indicates the initial and final temperature state.
TRAP-TYPE    

timeReferenceEvent 12
Tok_String
TRAP-TYPE    

shutdownEvent 13
This unit is shutting down as a result of a restart request.
TRAP-TYPE    

diagnosticEvent 14
This event is used for diagnostic purposes.
TRAP-TYPE    

configurationEvent 15
Tok_String
TRAP-TYPE    

unexpectedScsiInterruptEvent 16
A SCSI bus reports an unexpected interrupt.
TRAP-TYPE    

lipResetEvent 17
A Fibre Channel interface reports a LIP reset was received from a host.
TRAP-TYPE    

fcSystemErrorEvent 18
A Fibre Channel interace reports a system error.
TRAP-TYPE    

fcRequestTransferErrorEvent 19
A Fibre Channel interface reports an error processing a request.
TRAP-TYPE    

fcResponseTransferErrorEvent 20
A Fibre Channel interface reports an error processing a response.
TRAP-TYPE    

memoryFaultEvent 21
Processor memory fault detected.
TRAP-TYPE    

fcLipEvent 22
A Fibre Channel interface detected a LIP.
TRAP-TYPE    

fcLoopUpEvent 23
A Fibre Channel interface reports loop up.
TRAP-TYPE    

fcLoopDownEvent 24
A Fibre Channel interface reports loop down.
TRAP-TYPE    

pciBusParityErrorEvent 25
Parity error detected on unit internal PCI bus.
TRAP-TYPE    

pciInterfaceErrorEvent 26
Interface error detected on unit internal PCI bus.
TRAP-TYPE    

scsiDeviceAddedEvent 27
A device has been added to a SCSI bus.
TRAP-TYPE    

scsiBusResetEvent 28
A SCSI interface reports a bus reset was detected.
TRAP-TYPE    

deviceAddedEvent 29
This unit has added a device to its configuration table. Note: This trap is held off until the unit has been up for 60 seconds.
TRAP-TYPE    

deviceRemovedEvent 30
This unit has removed a device from its configuration table.
TRAP-TYPE    

loggingStartedEvent 31
Event logging service has started.
TRAP-TYPE    

loggingStoppedEvent 32
Event logging service has stopped.
TRAP-TYPE    

interfaceBusFaultEvent 33
An interface has detected a bus fault. The display string contained in varbind paEventVars contains the details of which interface detected the fault.
TRAP-TYPE    

interfaceDeviceFaultEvent 34
An interface has detected a device fault. The display string contained in varbind paEventVars contains the details of which interface detected the fault.
TRAP-TYPE    

scsiUnexpectedDisconnectEvent 35
A SCSI interface has reported an unexpected disconnect by a device.
TRAP-TYPE    

scsiParityErrorEvent 36
A SCSI interface has detected a parity error on the bus.
TRAP-TYPE    

fcPortDatabaseChangeEvent 37
Fibre Channel port databse change detected.
TRAP-TYPE    

ddfMemoryErrorEvent 38
An error was detected on the Direct Data Flow memory board.
TRAP-TYPE    

fcDirectoryServerChangeEvent 39
The Directory Server on the Fibre Channel fabric has changed.
TRAP-TYPE    

lunLimitExcededEvent 40
The maximum LUN limit has been exceded, too many devices connected.
TRAP-TYPE    

fcTransferFailureEvent 41
Fibre Channel transfer error.
TRAP-TYPE    

deviceLimitExcededEvent 42
The maximum device limit has been exceded, the persistent device map database is full.
TRAP-TYPE    

fcDebugDumpEvent 43
A Fibre Channel interface driver has reported a a debug dump.
TRAP-TYPE    

excessiveScsiBusErrorsEvent 44
Tok_String
TRAP-TYPE    

memoryScrubberErrorEvent 45
Tok_String
TRAP-TYPE    

srsDeviceCreatedEvent 46
A new SAN Replication Services device has been created
TRAP-TYPE    

srsDeviceOnlineEvent 47
A SAN Replication Services device has entered the online state.
TRAP-TYPE    

srsDeviceRemovedEvent 48
A SAN Replication Services device has been removed (deleted).
TRAP-TYPE    

srsDeviceFailedEvent 49
A SAN Replication Services device has failed.
TRAP-TYPE    

srsMemberAddedEvent 50
A new member LUN has been added to a SAN Replication Services device.
TRAP-TYPE    

srsMemberSuspendedEvent 51
A SAN Replication Services member has been suspended.
TRAP-TYPE    

srsMemberRemovedEvent 52
A SAN Replication Services member has been removed.
TRAP-TYPE    

srsMemberSyncStartedEvent 53
A SAN Replication Service member has begun synchronization to the primary member.
TRAP-TYPE    

srsMemberSyncDoneEvent 54
A SAN Replication Service member has completed synchronization to the primary member.
TRAP-TYPE    

srsMemberSyncErrorEvent 55
An error was detect during synchronization of a SAN Replication Service member to the primary member.
TRAP-TYPE    

srsMemberRetryEvent 56
A command issued to a SAN Replication Services member has failed and is being retried.
TRAP-TYPE    

srsMemberErrorEvent 57
A command issued to a SAN Replication Services member has resulted in an error.
TRAP-TYPE    

envPowerNominalEvent 58
Power has returned to nominal state from a warning or alarm state.
TRAP-TYPE    

envPowerWarningEvent 59
Power has entered a warning state from a nominal state (power degrading) or alarm state (power improving).
TRAP-TYPE    

envPowerAlarmEvent 60
Power has entered an alarm state.
TRAP-TYPE    

envTemperatureNominalEvent 61
Inlet air, outlet air, or I/O processor temperature has returned to nominal state from a warning or alarm state.
TRAP-TYPE    

envInletTemperatureWarningEvent 62
Inlet air temperature has entered a warning state from a nominal state (temperature increasing) or an alarm state (temperature decreasing).
TRAP-TYPE    

envInletTemperatureAlarmEvent 63
Inlet air temperature has entered an alarm state.
TRAP-TYPE    

envOutletTemperatureWarningEvent 64
Outlet air temperature has entered a warning state from a nominal state (temperature increasing) or an alarm state (temperature decreasing).
TRAP-TYPE    

envOutletTemperatureAlarmEvent 65
Outlet air temperature has entered an alarm state.
TRAP-TYPE    

envFanNominalEvent 66
Fan has entered a nominal state from a fault state.
TRAP-TYPE    

envFanWarningEvent 67
Fan has entered a warning range (tachometer fans only).
TRAP-TYPE    

envFanAlarmEvent 68
Fan has entered an alarm range (tachometer fans) or is stalled (rotor stall fans).
TRAP-TYPE    

eccMemoryErrorEvent 69
Error correcting code memory has detected an error.
TRAP-TYPE    

firmwareUploadCompleteEvent 70
Firmware upload process has completed.
TRAP-TYPE    

restartCompleteEvent 71
Restart process has completed.
TRAP-TYPE    

maxInitiatorsExceededEvent 72
Maximum number of initiators has been exceeded.
TRAP-TYPE    

powerSupplyOutOfSpecEvent 100
The main power supply voltage is out of specified operating range.
TRAP-TYPE    

auxPowerOutOfSpecEvent 101
The auxillary power supply voltage is out of specified operating range.
TRAP-TYPE    

newTemperatureChangeEvent 102
Temperature change detected since last report. The possible temperature states are OK, High, and Very High.
TRAP-TYPE    

newPciErrorsEvent 103
Tok_String
TRAP-TYPE    

newMemoryParityErrorsEvent 104
Tok_String
TRAP-TYPE    

pciBusInterfaceErrorEvent 105
Tok_String
TRAP-TYPE    

fcInterfaceFailureEvent 106
Fibre Channel interface failed Health Check.
TRAP-TYPE    

scsiInterfaceFailureEvent 107
SCSI interface failed Health Check.
TRAP-TYPE    

ssaInterfaceFailureEvent 108
SSA interface failed Health Check.
TRAP-TYPE    

deviceFailureEvent 109
Target device failed Health Check.
TRAP-TYPE    

fcLinkStatusChangeEvent 110
Fibre Channel link status has changed.
TRAP-TYPE    

newFcTranferErrorsEvent 111
New Fibre Channel transfer errors were detected since last report.
TRAP-TYPE    

logWillOverwriteEvent 150
The event log circular buffer is about to wrap, overwriting the oldest entries.
TRAP-TYPE    

bootCompletedEvent 4444
This unit has completed its boot sequence and is ready for SNMP communication with management applications. During the time period between the initiation of the boot (or reboot) sequence and the issuing of the bootCompletedEvent trap, certain data objects may not be completely initialized. As such, management applications should not attempt to retrieve data via SNMP until the bootCompletedEvent is issued.
TRAP-TYPE